Datasheet - Data Display Group

Datasheet
SGD
GVTSA4TNBL4E0
SG-01-015
The information contained in this document has been carefully researched and is, to the best
of our knowledge, accurate. However, we assume no liability for any product failures or
damages, immediate or consequential, resulting from the use of the information provided
herein. Our products are not intended for use in systems in which failures of product could
result in personal injury. All trademarks mentioned herein are property of their respective
owners. All specifications are subject to change without notice.
Product Specification
Model:
GVTSA4TNBL4E0
Rev. No.
Issued Date.
Page.
B
2012, SEP. 28
1 / 24
Thin-Film-Transistor LCD Module
Model: GVTSA4TNBL4E0
Acceptance
Solomon Goldentek Display Corp.
NO. 18 Ta-Yeh St., Ta-Fa Industrial Park,Ta-Liao
Hsiang, Kaohsiung Hsien 831, TAIWAN , R.O.C.
FAX: 886-7-7886800
Approved and Checked by
Approved by
Checked by
Made by
SGD
SGD
SGD
2012.09.28
2012.09.28
2012.09.28
呂家祥
蘇俊豪
趙長慶
Product Specification
Model:
GVTSA4TNBL4E0
Rev. No.
Issued Date.
Page.
B
2012, SEP. 28
2 / 24
Revise Records
Rev.
Date
A
2012/05/17
B
2012/09/28
Special Notes
Note1.
Note2.
Note3.
Note4.
Note5.
Contents
Written
Approved
Preliminary Specification
Aron Jau
James Lu
Update brightness 1300cd/m21500cd/m2
Aron Jau
James Lu
Product Specification
Model:
GVTSA4TNBL4E0
Rev. No.
Issued Date.
Page.
B
2012, SEP. 28
3 / 24
Contents
1.
1.1
1.2
2.
3.
3.1
3.2
3.3
3.4
4.
4.1
5.
5.1
5.2
5.3
6.
7.
8.
9.
General Description and Features
Features
LCD Module
Mechanical Information
Electrical Specifications
Absolute Max. Ratings
DC Electrical Characteristics of the Backlight
AC Timing Characteristic of The LCD
LVDS Switching Characteristics
Optical Characteristics
Optical characteristic of the LCD
I/O Terminal
Pin Assignment
Back-light
Block Diagram
Displayed Color and Input Data
Reliability Condition
Dimensional Outlines
Incoming Inspection Standards
4
4
4
4
5
5
8
9
11
13
13
16
16
17
17
18
19
20
21
Product Specification
Model:
GVTSA4TNBL4E0
Rev. No.
Issued Date.
Page.
B
2012, SEP. 28
4 / 24
1. General Description and Features
GVTSA4TNBL4E0 is a transmissive type color active matrix TFT (Thin Film Transistor) liquid crystal display
(LCD) that uses amorphous silicon TFT as a switching device. This model is composed of a TFT-LCD
module, a receiver circuit, and a back-light unit. Graphics and texts can be displayed on a WVGA 800 (W)
x 3 x 600 (H) dots (4:3 aspect ratio) with 262,144 colors by supplying 18 bits data signal (6bits/each
color). The following table described the features of GVTSA4TNBL4E0.
1.1 Features
-
Transmissive and back-light with 30 LEDs are available.
-
TN (Twisted Nematic) mode.
-
LVDS Receiver 18 bit Interface.
-
High brightness
1.2 LCD Module
Item
Specification
Unit
10.4 inches
Diagonal
800 (H) x 600 (V)
Pixel
211.2 (H) x 158.4 (V)
mm
243 (H) x 185.6 (V) x 7.3 (T)
mm
Normally white mode/ Transmissive
--
Surface Treatment
Anti-glare(AG)
--
Pixel Arrangement
R,G,B Vertical Stripe
--
192 x 180.5
um
262k
--
6 o’clock
--
LVDS Receiver 18 bit Interface
--
Screen Size
Display Resolution
Active Area
Outline Dimension
Display Mode
Pixel Size
Display Color
Viewing Direction
Input Interface
2.
Mechanical Information
Item
Module Size
Weight
Min.
Typ.
Max.
Unit
Horizontal (H)
--
243
--
mm
Vertical (V)
--
185.6
--
mm
Thickness (T)
--
7.3
--
mm
(1)
--
(TBD)
--
g
--
Note (1) Not Include Component. Refer to the Outline Dimension Drawing as attached.
Note
Product Specification
Model:
3.
GVTSA4TNBL4E0
Rev. No.
Issued Date.
Page.
B
2012, SEP. 28
5 / 24
Electrical Specifications
3.1 Absolute Max. Ratings
3.1.1
Absolute Ratings of Environment
If the operating condition exceeds the following absolute maximum ratings, the TFT LCD module may be
damaged permanently.
(Ta=252°C, GND=0)
Item
Symbol
Min.
Max.
Unit
Note
Storage temperature
TSTG
-30
80
°C
(1)
Operating temperature
TOPR
-20
70
°C
(1)
Note (1) Only operation is guarantied at operating temperature. Contrast, response time, another
display quality are evaluated at +25°C.
Product Specification
Model:
GVTSA4TNBL4E0
Rev. No.
Issued Date.
Page.
B
2012, SEP. 28
6 / 24
3.1.2 Electrical Absolute Maximum Ratings
(VSS=GND=0)
Parameter
Power supply Logic voltage
Permissive input ripple voltage
Symbol
Min.
Max.
Unit
VDD
-0.3
4.0
V
VRF
--
100
mVp-p
Remark
VDD=+3.3V
(1) Device is subject to be damaged permanently if stresses beyond those absolute maximum ratings
listed above.
3.1.3 Backlight Unitfe
(VSS=GND=0)
Parameter
Symbol
Min.
Max.
Unit
Current of Backlight Unit
IB
--
600
mA
Voltage of Backlight Unit
VB
--
22
V
3.1.4 Display On/Off Sequence
Remark
Product Specification
Model:
3.1.5
GVTSA4TNBL4E0
Rev. No.
Issued Date.
Page.
B
2012, SEP. 28
7 / 24
DC Electrical Characteristics of the TFT LCD
(Ta=252°C, VSS=GND=0)
Item
Symbol
Min.
Typ.
Max.
Unit
Power supply Logic Voltage
VDD
3.0
3.3
3.6
V
H Level
VIH
0.7xVDD
-
VDD
V
L Level
VIL
0
-
0.3xVDD
V
ICC
-
(180)
(220)
mA
Input Voltage for
logic
Power Supply current
Note1:
fv =60Hz , Ta=25°C , Display pattern : Black pattern
Remark
Note 1
Product Specification
Model:
GVTSA4TNBL4E0
Rev. No.
Issued Date.
Page.
B
2012, SEP. 28
8 / 24
3.2 DC Electrical Characteristics of the Backlight
The Back-light system is an edge-lighting type with 30 white LED (Light Emitting Diode)s.
(Ta= 252°C)
Characteristics
Symbol
Min.
Typ.
Max.
Unit
Forward Voltage
VB
(17)
(18)
(21.6)
V
Forward Current
IB
-
500
600
mA
(1)
Power Consumption
PBL
-
9000
12960
mW
(2)
-
(50000)
(60000)
-
hr
(3)
LED Life time
Note (1) LEDs in 6 series x 5 parallel type.
(2) Where IB =500mA, VB = 18, PBL = VB × IB
(3) The environmental conducted under ambient air flow ,at Ta=25±2°C, 60%RH±5%
Note
Product Specification
Model:
GVTSA4TNBL4E0
Rev. No.
Issued Date.
Page.
B
2012, SEP. 28
9 / 24
3.3 AC Timing Characteristic of The LCD
3.3.1
Tliming Condition
Signal
DCLK
Horizontal
Timing
Vertical
Timing
3.3.2
Parameter
Symbol
Min.
Typ.
Max.
Unit.
CLK frequency
fclk
-
40
50
MHz
CLK period
tclk
20
25
-
ns
CLK pulse duty
tcwh
40
50
60
%
One Horizontal Line
th
862
1056
1200
DCLK
Horizontal Display Area
thd
-
800
-
DCLK
HS pulse width
thpw
1
-
40
DCLK
HS Back Porch
thb
46
46
46
DCLK
HS Front Porch
thfp
16
210
354
DCLK
VS period time
tv
624
635
700
TH
Vertical Display Area
tvd
-
600
-
TH
VS pulse width
tvpw
1
-
20
TH
VS Back Porch
tvb
23
23
23
TH
VS Front Porch
tvfp
1
12
77
TH
Remark
blanking
blanking
Clock and Data input waveforms
Parameter
Symbol
Min.
Typ.
Max.
Unit.
HS setup time
Thst
8
-
-
ns
HS hold time
Thhd
8
-
-
ns
VS setup time
Tvst
8
-
-
ns
VS hold time
Tvhd
8
-
-
ns
Data setup time
Tdsu
8
-
-
ns
Data hold time
Tdhd
8
-
-
ns
DE setup time
Tesu
8
-
-
ns
DE hold time
Tehd
8
-
-
ns
CLKIN cycle time
Tcph
20
-
ns
Remark
Product Specification
Model:
3.3.3
Timing Characteristic
3.3.3.1 Horizontal Timing
GVTSA4TNBL4E0
Rev. No.
Issued Date.
Page.
B
2012, SEP. 28
10 / 24
Product Specification
Model:
GVTSA4TNBL4E0
Rev. No.
Issued Date.
Page.
B
2012, SEP. 28
11 / 24
3.3.3.2 Vertical Timing
3.4 LVDS Switching Characteristic
3.4.1 LVDS Timing Condition
Symbol
Parameter
Min.
Typ.
Max.
Unit.
VDD = 3.0 - 3.6V
11.76
T
50.0
ns
VDD = 2.5 - 3.6V
14.28
T
50.0
ns
tRCP
CLK OUT Period
tRCH
CLK OUT High Time
-
4T/7
-
ns
tRCL
CLK OUT Low Time
-
3T/7
-
ns
tRCD
RCLK +/- to CLK OUT Delay
-
5T/7
-
ns
tRS
TTL Data Setup to CLK OUT
0.35T-0.3
-
-
ns
tRH
TTL Data Hold from CKL OUT
0.45T-1.6
-
-
ns
tTLH
TTL Low to High Transition Time
-
2.0
3.0
ns
tTHL
TTL High to Low Transition Time
-
1.8
3.0
ns
tRIP1
Input Data Position0 (T = 11.76ns)
-0.4
0.0
0.4
ns
tRIP0
Input Data Position1 (T = 11.76ns)
T/7-0.4
T/7
T/7+0.4
ns
tRIP6
Input Data Position2 (T = 11.76ns)
2T/7-0.4
2T/7
2T/7+0.4
ns
tRIP5
Input Data Position3 (T = 11.76ns)
3T/7-0.4
3T/7
3T/7+0.4
ns
tRIP4
Input Data Position4 (T = 11.76ns)
4T/7-0.4
4T/7
4T/7+0.4
ns
tRIP3
Input Data Position5 (T = 11.76ns)
5T/7-0.4
5T/7
5T/7+0.4
ns
tRIP2
Input Data Position6 (T = 11.76ns)
6T/7-0.4
6T/7
6T/7+0.4
ns
tRPLL
Phase Lock Loop Set
10.0
ms
Note
Product Specification
Model:
3.4.2 LVDS AC Timing
GVTSA4TNBL4E0
Rev. No.
Issued Date.
Page.
B
2012, SEP. 28
12 / 24
Product Specification
Model:
GVTSA4TNBL4E0
Rev. No.
Issued Date.
Page.
B
2012, SEP. 28
13 / 24
4. Optical Characteristics
4.1 Optical characteristic of the LCD
The following items are measured under stable conditions. The optical characteristics should be measured
in a dark room or equivalent state with the methods.
Measuring equipment: BM-7A
Item
Symbol
Brightness
B
Tr
Response time
Tf
Contrast ratio
CR
Luminance Uniformity
ΔL
Color
Chromaticity
(CIE 1931)
Viewing Angle
(6H)
Condition
Wx
White
Wy
Hor.
Ver.
=0
At
optimized
viewing
angle
=0
Normal
Viewing
Angle
R
L
U
D
CR10
Min
Type
Max
Unit
(1200)
(1500)
--
cd/m2
-
5
10
ms
--
15
20
ms
(300)
(500)
--
--
70
75
(0.270)
(0.320)
(0.370)
(0.300)
(0.350)
(0.400)
60
70
--
60
70
--
40
50
--
50
60
--
Note
.
%
--
Degree
BM-7A
Product Specification
Model:
GVTSA4TNBL4E0
Rev. No.
Issued Date.
Page.
B
2012, SEP. 28
14 / 24
a. Test equipment setup
After stabilizing and leaving the panel alone shall be warmed up for the stable operation of LCM,
the measurement should be executed. Measurement should be executed in a stable, windless, and
dark room. Optical specifications are measured by Topcon BM-7A(fast) with a viewing angle of 2
at a distance of 50cm and normal direction.
b. Definition of response time: Tr and Tf
The response time is defined as the following figure and shall be measured by switching the input
signal for “black” and “white”.
c.
Definition of contrast ratio:
Brightness measured when LCD is at “white state”
Contrast Ratio (CR) =

Brightness measured when LCD is at “black state”
d. Measured at the center area of the panel when all the input terminals of LCD panel are electrically
opened.
Product Specification
Model:
GVTSA4TNBL4E0
Rev. No.
Issued Date.
Page.
B
2012, SEP. 28
15 / 24
e. View Angle
f.
Definition of Luminance of White: Luminance of white at the center points
Light Source of Back-Light Unit
LED Type
g. Definition of White Uniformity
White Uniformity =
Min. luminance of white among 9-points

Max. luminance of white among 9-points
X
100%
Product Specification
Model:
5.
GVTSA4TNBL4E0
Rev. No.
Issued Date.
Page.
B
2012, SEP. 28
16 / 24
I/O Terminal
5.1
Pin Assignment (CN1 connector part No: MSB24013P20HA or equivalent.)
Pin No.
Symbol
I/O
Function
1
VDD
P
Power Supply Logic voltage +3.3V
2
VDD
P
Power Supply Logic voltage +3.3V
3
GND
P
Ground
4
GND
P
Ground
5
RxIN0-
I
Negative LVDS differential data input
6
RxIN0+
I
Positive LVDS differential data input
7
GND
P
Ground
8
RxIN1-
I
Negative LVDS differential data input
9
RxIN1+
I
Positive LVDS differential data input
10
GND
P
Ground
11
RxIN2-
I
Negative LVDS differential data input
12
RxIN2+
I
Positive LVDS differential data input
13
GND
P
Ground
14
RxCLKIN-
I
Negative LVDS differential clock input
15
RxCLKIN+
I
Positive LVDS differential clock input
16
GND
P
Ground
17
NC
-
No Connect
18
NC
-
No Connect
19
NC
-
No Connect
20
NC
-
No Connect
I: Input, O: Output, P: Power
Notes:
1) GND Pin must ground contact, can not be floating.
2) NC pin must no contact.
Remark
Product Specification
Model:
5.2
GVTSA4TNBL4E0
Issued Date.
Page.
B
2012, SEP. 28
17 / 24
Back-light (Connector Part No: JST:BHSR-02VS-01(N) or equivalent.)
Pin No.
Symbol
1
LEDA
Power Supply for LED backlight
2
LEDK
GND for LED backlight
5.3
Rev. No.
Function
RG B
TFT LCD PANEL
800(RGB)X600 dots
RG BRG B
RG B
Source Driver
&
Gate Driver
VDD,GND
RxIN0±,RxIN1±,
RxIN2±,RxCLKIN±
Red
White
Block Diagram
RG BRG B
Remark
Product Specification
Model:
6.
GVTSA4TNBL4E0
Rev. No.
Issued Date.
Page.
B
2012, SEP. 28
18 / 24
Displayed Color and Input Data
Basic
Color
Red
Green
Blue
Color
& Gray
Scale
Black
Red
Green
Blue
Cyan
Magenta
Yellow
White
Black
Red(1)
Red(2)
:
Red(31)
:
Red(62)
Red(63)
Black
Green(1)
Green(2)
:
Green(31)
:
Green(62)
Green(63)
Black
Blue(1)
Blue(2)
:
Blue(31)
:
Blue(62)
Blue(63)
Data Signal
R5 R4 R3 R2 R1 R0 G5 G4 G3 G2 G1 G0 B5 B4 B3 B2 B1 B0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
1
1
1
1
1
1
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
1
1
1
1
1
1
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
1
1
1
1
1
1
0
0
0
0
0
0
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
0
0
0
0
0
0
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
0
0
0
0
0
0
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
1
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
1
0
0
0
0
0
0
0
0
0
0
0
0
0
:
:
:
:
:
:
:
:
:
:
:
:
:
:
:
:
:
:
0
1
1
1
1
1
0
0
0
0
0
0
0
0
0
0
0
0
:
:
:
:
:
:
:
:
:
:
:
:
:
:
:
:
:
:
1
1
1
1
1
0
0
0
0
0
0
0
0
0
0
0
0
0
1
1
1
1
1
1
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
1
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
1
0
0
0
0
0
0
0
:
:
:
:
:
:
:
:
:
:
:
:
:
:
:
:
:
:
0
0
0
0
0
0
0
1
1
1
1
0
0
0
0
0
0
0
:
:
:
:
:
:
:
:
:
:
:
:
:
:
:
:
:
:
0
0
0
0
0
0
1
1
1
1
1
0
0
0
0
0
0
0
0
0
0
0
0
0
1
1
1
1
1
1
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
1
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
1
0
:
:
:
:
:
:
:
:
:
:
:
:
:
:
:
:
:
:
0
0
0
0
0
0
0
0
0
0
0
0
0
1
1
1
1
1
:
:
:
:
:
:
:
:
:
:
:
:
:
:
:
:
:
:
0
0
0
0
0
0
0
0
0
0
0
0
1
1
1
1
1
0
0
0
0
0
0
0
0
0
0
0
0
0
1
1
1
1
1
1
0 : Low level voltage, 1 :High level voltage
Each basic color can be displayed in 64 gray scales from 6 bit data signals. With the combination of total 18
bit data signals, the 262,144-color display can be achieved on the screen.
Product Specification
Model:
7.
GVTSA4TNBL4E0
Rev. No.
Issued Date.
Page.
B
2012, SEP. 28
19 / 24
Reliability Condition
No change on display and in operation under the following test condition.
Condition: Unless otherwise specified, tests will be conducted under the following condition.
Temperature: 205C.
Humidity: 655RH.
Tests will be not conducted under functioning state.
No.
Parameter
Condition
Notes
1
High Temperature Operating
70C2C, 240hrs (Operation state).
2
Low Temperature Operating
-20C2C, 240hrs (Operation state).
1
3
High Temperature Storage
80C2C, 240hrs.
2
4
Low Temperature Storage
-30C2C, 240hrs.
1,2
5
High Temperature and High
Humidity Operation Test
60C2C, 90%, 240hrs.
1,2
Total fixed amplitude: 1.5mm.
6
Vibration Test
Vibration Frequency: 1055Hz.
One cycle 60 seconds to 3 direction of X, Y, Z each 15
minutes.
3
To be measured after dropping from 60cm high on the
concrete surface in packing state.
Dropping method corner
dropping:
7.
Drop Test
A corner: Once edge
dropping.
B, C, D edge: Once face
dropping.
E, F, G face: Once.
Notes:
1. No dew condensation to be observed.
2. The function test shall be conducted after 4 hours storage at the normal temperature and
humidity after removed from the test chamber.
3. Vibration test will be conducted to the product itself without putting I in a container.
APPROVED
01
DATE
2012.04.19
SCALE
VERSION
NAME
OUTLINE
GVTSA4TNBL4E0
APPROVED
293\F:\圖紙\10.4\SVGA\GVTSA4TNBL4E0
FILE NAME
mm
DRAWN
1/1
CHECKED
MODEL NAME
TITLE
FINISH
UNIT
NO.
MATERIAL
DATE
GVTSA4TNBL4E0
±0.3
REVISION RECORD
Model:
TOLERANCE
1
8.
REV
Product Specification
Rev. No.
Issued Date.
Page.
B
2012, SEP. 28
20 / 24
Dimensional Outlines
Product Specification
Model:
GVTSA4TNBL4E0
Rev. No.
Issued Date.
Page.
B
2012, SEP. 28
21 / 24
9. Incoming Inspection Standards
9.1 Inspection and Environment Conditions
9.1.1 Inspection Conditions:
(1)Inspection Distance: 35 cm±5cm
(2)View Angle : Light-on Inspection Angle︰±5°
Cosmetic Inspection Angle︰±45°
Light-on Insp.
Cosmetic Insp.
45°
30cm~40cm
5°
90°
TFT-LCD
( perpendicular to LCD panel surface)
9.1.2 Environment Conditions:
Ambient Temperature
Ambient Humidity
Ambient
Illumination
23℃±5℃
55±10%RH
Cosmetic Inspection
more than 600 Lux
Functional Inspection
300~500 Lux
9.1.3 Sampling Conditions:
(1) Lot Size: Quantity of shipment lot per model
(2) Sampling Method:
Sampling Plan
AQL
Major Defect
Minor Defect
MIL-STD-105E
Normal Inspection, Single Sampling
Level II
1.0%
1.5%
(3) The classification of Major(MA) and Minor(MI) defects is shown as 3. Inspection Criteria.
Product Specification
Model:
GVTSA4TNBL4E0
Rev. No.
Issued Date.
Page.
B
2012, SEP. 28
22 / 24
9.1.4 Inspection Criteria
9.1.4.1 Cosmetic Inspection(Panel):
Item
Judgment Criteria
a
b
b
a
b
Chipping on Panel
Classification
a
b
c
MA
a≦3.0mm、b≦3.0mm、c≦t
( Bottom glass thickness)
Scratch on Panel
*Note-2
Bubble or Dent on
Panel
*Note-3
W≦0.05mm or L< 5mm: Ignored
0.05mm<W≦0.1mm and L≦5mm: N≦5
MI
W>0.1mm or L>5mm: Not allowed
D≦0.2mm: Ignored
0.2mm<D≦0.3mm: N≦5
MI
D>0.3mm: Not allowed
Panel Crack
MA
Not Allowed crack
Bezel Deformation
Bezel Oxidation
Bezel Scratch
Metal Squash Dent
/Flange(Front Side)
B/L High Voltage Wire
Denudation
Polarizer flaw or leak
out resin
Outline Dimension
Obvious deformation is not allowed.
Not allowed if it rusts continuously over 1 cm (It is out of
warranty with rusted tin plate)
MI
MI
L≦20mm , W≦0.2 , N≦3
MI
D(W)≦1,L≦3,N≦3;
MI
Not allowed
MA
Defect is defined as the active area.
MI
Must in Spec, refer to related product spec.
MI
Product Specification
Model:
GVTSA4TNBL4E0
Rev. No.
Issued Date.
Page.
B
2012, SEP. 28
23 / 24
9.1.4.2 Functional Inspection:
Judgment Criteria
Item
Area(Note1)
I
Random
3 dots adjacent or more
0
0
0
0
Random
3
2 dots adjacent
0
3 dots adjacent or more
Point Defect
Classification
2
Bright dot 2 dots adjacent
Dark dot
O
Total Dot Defect
Distance between Bright
and Bright dot
Distance between Bright
Distance
and Dark dot
Distance between Dark
dot
0
0
5
L≧5mm
MI
L≧5mm
L≧5mm
(1) It is defined as Point Defect if defect area>0.5dot
(2) It is ignored if defect area≦0.5dot
(3)Weak point defect will be defined as Bright Dot if it can be
observed through ND filter 5%( Full Screen Black Inspection)
Line Defect
Obvious vertical or horizontal line defect is not allowed.
MA
Mura
Not allowed if it can be observed through ND Filter 5 %
MI
Foreign Material
in spot shape
*Note-3
D≦0.2mm: Ignored
0.2mm<D≦0.5mm: N≦8
MI
Foreign Material
in line
or spiral shape
*Note-4
Display
Function Abnormal
W≦0.05mm or L≦5mm: Ignored
0.05mm<W≦0.2mm and L1.0mm≦5mm: N≦8
D>0.5mm: Not allowed
MI
W>0.2mm or L>5mm: Not allowed
No Malfunction can be allowed
MA
Product Specification
Model:
Note-1︰
I/O Area Definition
GVTSA4TNBL4E0
Rev. No.
Issued Date.
Page.
B
2012, SEP. 28
24 / 24
Note-2︰ Polarizer Scratch
L
W
Note-3︰Spot Foreign Material
(W ≧L / 4 )
Note-4︰Line or Spiral Foreign Material
(W<L / 4)
L
W
(L  W )
D
2
L
W
Our company network supports you worldwide with offices in Germany, Great Britain, Italy, Turkey and the
USA. For more information please contact:
Distec GmbH
Display Technology Ltd.
Augsburger Str. 2b
5 The Oaks Business Village
82110 Germering
Revenge Road, Lordswood
Germany
Chatham, Kent, ME5 8LF
United Kingdom
Phone:
+49 (0)89 / 89 43 63-0
Phone:
+44 (0)1634 / 67 27 55
Fax:
+49 (0)89 / 89 43 63-131
Fax:
+44 (0)1634 / 67 27 54
E-Mail:
info@datadisplay-group.de
E-Mail:
info@datadisplay-group.co.uk
Internet:
www.datadisplay-group.de
Internet:
www.datadisplay-group.co.uk
Apollo Display Technologies, Corp.
87 Raynor Avenue, Unit 1Ronkonkoma, NY
11779
United States of America
Phone:
+1 631 / 580-43 60
Fax:
+1 631 / 580-43 70
E-Mail:
info@datadisplay-group.com
Internet: www.datadisplay-group.com
Sales Partner:
Sales Partner:
REM Italy s.a.s.
DATA DISPLAY BİLİŞİM TEKNOLOJİLERİ
di Michieletto Flavio & C.
İÇ VE DIŞ TİCARET LİMİTED ŞİRKETİ
Via Obbia Bassa, 10
Barbaros Mh Ak Zamabak Sk A Blok
I-35010 Trebaseleghe (PD)
D:143 Ataşehir/İstanbul
Italy
Turkey
Phone: +39 335 521 37 89
Phone: +90 (0)216 / 688 04 68
E-Mail: info@remitaly.com
Fax:
Internet:www.remitaly.com
E-Mail: info@data-display.com.tr
+90 (0)216 / 688 04 69
Internet:www.data-display.com.tr
Download PDF
Similar pages