Regency HZ33CE Gas Fireplace - Regency Ignite Dealer Portal Login

Regency HZ33CE
Gas Fireplace
Owners &
Installation Manual
MODEL: HZ33CE-NG Natural Gas
HZ33CE-LP Propane
HZ33CE Video
www.regency-fire.com
WARNING:
If the information in these instructions are not followed exactly,
a fire or explosion may result causing property damage,
personal injury or loss of life.
FOR YOUR SAFETY
What to do if you smell gas:
Do not try to light any appliance
Do not touch any electrical switch:
do not use any phone in your
FOR YOUR SAFETY
building.
Do not store or use gasoline or other flammable vapors and Immediately call your gas supplier
liquids in the vicinity of this or any other appliance.
from a neighbour's phone. Follow
the gas supplier's instructions.
Installation and service must be performed by a qualified
If you cannot reach your gas
installer, service agency or the gas supplier.
supplier, call the fire department.
Tested by:
919-120a
Installer: Please complete the details on the back cover
and leave this manual with the homeowner.
Homeowner: Please keep these instructions for future reference.
FPI FIREPLACE PRODUCTS INTERNATIONAL LTD. 6988 Venture St., Delta, BC Canada, V4G 1H4
11/18/14
To the New Owner:
Congratulations!
You are the owner of a state-of-the-art Gas Fireplace by REGENCY®. The HZ33CE has been
designed to provide you with all the warmth and charm of a fire at the flick of a switch. The model
HZ33CE has been approved by Warnock Hersey for both safety and efficiency. As it also bears
our own mark, it promises to provide you with economy, comfort and security for many trouble
free years to follow. Please take a moment now to acquaint yourself with these instructions and
the many features of your Regency® Fireplace.
Horizon Benefits Video
2
HZ33CE Video
Regency HZ33CE Gas Fireplace
MANUFACTURED MOBILE HOME REQUIREMENTS
INFORMATION FOR MOBILE/MANUFACTURED HOMES AFTER FIRST SALE
This Regency® product has been tested and listed by Warnock Hersey as a Direct Vent Wall Furnace to the following standards: VENTED
GAS FIREPLACE HEATERS ANSI Z21.88 - 2009 / CSA 2.33 - 2009 and GAS-FIRED APPLIANCES FOR USE AT HIGH ALTITUDES CAN
/ CGA 2.17-M91.
This Direct Vent System Appliance must be installed in accordance with the manufacturer's installation instructions and the Manufactured
Home Construction and Safety Standard, Title 24 CFR, Part 3280, or the current Standard of Fire Safety Criteria for Manufactured Home
Installations, Sites, and Communities ANSI/NFPA 501A, and with CAN/CSA Z240-MH Mobile Home Standard in Canada.
This appliance installation must comply with the manufacturer's installation instructions and local codes, if any. In the absence of local codes
follow the current National Fuel Gas Code, ANSI Z223.1 and the current National Electrical Code ANSI/NFPA 70 in the U.S.A., and the current
CAN/CGA B149 Gas Installation Code and the current Canadian Electrical Code CSA C22.1 in Canada.
This appliance comes equipped with a dedicated #8 Ground Lug for attachment of the ground wire to the steel chassis as applicable to local
codes.
The appliance, when installed, must be electrically grounded in accordance with local codes or, in the absence of local codes, with the
National Electrical Code, ANSI/NFPA 70, or the Canadian Electrical Code, CSA C22.1.
This appliance may only be installed in an aftermarket permanently located, manufactured (U.S.A only) or mobile home, where not prohibited
by local codes.
This appliance can only be used with the type of gas indicated on the rating plate. This appliance is not convertible for use with other gases,
unless a certified kit is used. (Kit # 434-972).
Ensure that structural members are not cut or weakened during installation.
Regency HZ33CE Gas Fireplace
3
TABLE OF CONTENTS
SAFETY LABEL
Copy of Safety Decal......................................................5
REQUIREMENTS
MA Code - CO Detector.................................................6
DIMENSIONS
Unit Dimensions.............................................................7
4 sided faceplate Dimensions........................................7
Mantel Dimensions.........................................................7
INSTALLATION
Important Message .......................................................8
Before You Start.............................................................8
General Safety Information............................................8
Installation Checklist.......................................................9
Locating Your Gas Fireplace..........................................9
Clearances...................................................................10
Mantel Leg Clearances................................................ 11
Mantel Clearances....................................................... 11
Framing & Finishing.....................................................12
Tile Finish.............................................................12
Important message...............................................13
Clean Finish..........................................................14
Framing Dimensions....................................................15
Venting Introduction......................................................16
Exterior Vent Termination Requirements......................17
Regency® Direct Vent flex System ...............................18
Rigid Pipe Venting Systems.........................................19
4" X 6-5/8" RigiD Pipe Cross Reference Chart.............20
Rigid Pipe Venting Arrangements ................................22
Vertical Termination with Co-Linear Flex System.........23
Venting Arrangements - Vertical Terminations .............24
Unit installation with Horizontal termination..................29
Unit installation with Vertical Termination.....................30
Gas Line Installation.....................................................30
Pilot Adjustment............................................................31
High Elevation..............................................................31
886 S.I.T. Valve Description..........................................31
Gas Pipe Pressure Testing...........................................31
Conversion from NG to LP...........................................32
Wiring Diagrams ..........................................................38
Proflame system GT ....................................................38
Proflame system GTM .................................................39
Proflame system GTMF with optional fan....................39
4
Installing the Optional Fan (Prior to unit installation)....41
Optional fan Wiring Diagram .......................................42
Installing the Optional Fan (installed unit)....................42
Optional Wall Thermostat ............................................44
Battery Installation........................................................44
Optional Remote Control..............................................44
Wall Switch...................................................................44
Aeration Adjustment.....................................................44
Optional Reflective Panel Installation...........................45
Glass Crystals AND optional stones.............................46
Installation On Burner and Firebox Floor.....................46
Optional Spa Stones Installation .................................46
Optional log set Installation..........................................47
Glass screen guard and Glass Door installation..........50
Standard Flush Door and screen.................................50
Optional 4-sided faceplate installation..................51
Optional mantel installation...................................52
OPERATING INSTRUCTIONS
Operating Instructions..................................................53
First Fire.......................................................................53
Lighting Procedure.......................................................53
Shutdown Procedure....................................................53
Normal Operating Sounds of Gas Appliances..............53
Copy of Lighting Plate Instructions...............................54
MAINTENANCE
Maintenance Instructions.............................................55
General Vent Maintenance...........................................55
Glass Door...................................................................55
Glass Replacement..............................................55
Valve Tray Replacement...............................................56
PARTS LIST
Main Assembly.............................................................57
Accessories..................................................................58
WARRANTY
The Warranty: Limited Lifetime ....................................59
Regency HZ33CE Gas Fireplace
SAFETY LABEL
This is a copy of the label that accompanies each HZ33CE Direct Vent Gas Fireplace. We have printed a copy of the contents here for your review.
NOTE: Regency® units are constantly being improved. Check the label on the unit and if there is a difference, the label on the unit is the correct one.
COPY OF SAFETY DECAL
Duplicate S/N
Listed: VENTED GAS FIREPLACE HEATER
Certified for/Certifiée pour: CANADA and U.S.A.
Tested to: CAN/CGA-2.17-M91(R2009)
ANSI Z21.88-2009/CSA 2.33-2009
406
DO NOT REMOVE THIS LABEL / NE PAS ENLEVER CETTE ÉTIQUETTE
Serial No./ No de serie
406
4001172
MAY BE INSTALLED IN MANUFACTURED (MOBILE) HOMES AFTER FIRST SALE.
NATURAL GAS: Model HZ33CE-NG
Model/Modele:
HZ33CE-NG
Minimum supply pressure 5"
Manifold pressure high 3.5"
Manifold pressure low
1.6"
# 47
Orifice size
12,000
Minimum input
17,000
Maximum input
0-4500
Altitude
Model/Modele:
HZ33CE-LP
Minimum supply pressure 11"
Manifold pressure high 10"
Manifold pressure low
6.4"
Orifice size
# 56
Minimum input
12,500
15,000
Maximum input
0-4500
Altitude
WC
WC
WC
DMS
Btu/h
Btu/h
ft/pi
Minimum Clearances to Combustibles
Degagement Minimum De Materiaux Combustibles
Ceiling
0" Clearance to
combustibles from:
Sides, bottom and rear of unit
*Top - 3-1/2" (89mm) non-combustible
material required above unit.
A
APPAREIL FONCTIONNANT AU NATURAL GAS
CONCU POUR ETRE POELE: Modéle HZ33CE-NG
(1.25 kPa)
(0.87 kPa)
(0.39 kPa)
(3.51 kW)
(4.98 kW)
(0-1372 m)
PROPANE: Model HZ33CE-LP
Pression d'allimentation minimum
Pression a la tubulure d'échappement élevée
Pression a la tubulure d'échappement basse
Grandeur de l'injecteur
Débit Califorique minimum selon
Débit Caliorfique maximum selon
l'altitude
Wall
Ceiling Clearances from
Top Opening of Unit:
(A) 30" (762mm)
Side Wall Clearance from
Side Opening of Unit:
B) 9"(229mm)
APPAREIL FONCTIONNANT AU PROPANE
CONCU POUR ETRE POELE: Modéle HZ33CE-LP
WC (2.73 kPa) Pression d'allimentation minimum
WC (2.49 kPa) Pression a la tubulure d'échappement élevée
WC (1.59 kPa) Pression a la tubulure d'échappement basse
Grandeur de l'injecteur
DMS
Btu/h (3.66 kW) Débit Califorique minimum selon
Btu/h (4.39 kW) Débit Caliorfique maximum selon
ft/pi
(0-1372 m) l'altitude
Floor Clearance:
C) 0”
C
Floor
DOOR SEAL: Please check that
the door is properly sealed
Alcove Clearances
D) Min. Width 84" (1219mm)
E) Max. Depth 36" (914mm)
(See Instruction Manual for Detailed Instructions)
This appliance must be installed in accordance with local codes, if any; if none, follow the National Fuel Gas Code, ANSI Z223.1, or Natural Gas and Propane Installation Code, CSA B149.1.
This appliance must be installed in accordance with the Standard CAN/CSA Z240 MH, Mobile Housing, in Canada, or with the Manufactured Home Construction and Safety Standard, Title 24 CFR, Part 3280, in the
United States, or when such a standard is not applicable, ANSI/NCSBCS A225.1/NFPA 501A, Manufactured Home Installations Standard
This appliance is only for use with the type of gas indicated on the rating plate and may be installed in an aftermarket, permanently located, manufactured (mobile) home where not prohibited by local codes. See
owner's manual for details. Fan (Part # 432-917)
Installer l'appareil selon les codes ou règlements locaux, ou, en l'absence de tels règlements, selon les codes d'installation ANSI Z223.1, National Fuel Gas Code ou CSA-B149.1 en vigueur.
Installer l'appareil selon la norme CAN/CSA-Z240, Série MM, Maison mobiles ou CAN/CSA-Z240 VC, Véhicules de camping, ou la norme 24 CFR Part 3280, Manufactured Home Construction and Safety Standard.
Si ces normes ne sont pas pertinentes, utilisez la norme ANSI/NCSBCS A225.1/NFPA 501A, Manufactured Home Installations Standard.
Cet appareil doit être utilize uniquement avec le type de gaz indiqué sur la plaque signalétique. Cet appareil peut être installé dans une maison préfabriquée ou mobile (É.-U. seulement) installée à demeure si les
règlements locaux le permettent. Voir la notice de l'utilisateur pour plus de renseignements. Cet appareil ne peut pas être utilisé avec d'autres gaz sauf si une trousse de conversion certifiée est fournie.
This vented gas fireplace heater is not for use with air filters.
Ne pas utiliser de filtre à air avec ce foyer au gaz à évacuation.
Electrical supply / Électrique 115VAC, 1.13 A, 60Hz.
For use with glass doors certified with the appliance only
Pour utilisation uniquement avec les portes en verre certifiées avec l'appareil
VENTED GAS FIREPLACE HEATER - NOT FOR USE WITH SOLID FUELS.
FOYER AU GAZ À ÉVACUATION - NE PAS UTILISER AVEC DUCOMBUSTIBLE SOLIDE.
FPI Fireplace Products International Ltd.
Delta, BC, Canada
Made in Canada / Fabrique au Canada
919-119
For the State of Massachusetts, installation
and repair must be done by a plumber or
gas fitter licensed in the Commonwealth of
Massachusetts.
For the State of Massachusetts, flexible connectors shall not exceed 36 inches in length.
For the State of Massachusetts, the appliances individual manual shut-off must be a
t-handle type valve.
The State of Massachusetts requires the
installation of a carbon monoxide alarm in
accordance with NFPA 720 and a CO alarm
with battery back up in the same room where
the gas appliance is installed.
Regency HZ33CE Gas Fireplace
5
REQUIREMENTS
MA Code - CO Detector
(for the State of Massachusetts only)
5.08: Modifications to NFPA-54, Chapter 10
(2) Revise 10.8.3 by adding the following additional requirements:
(a) For all side wall horizontally vented gas fueled equipment installed in every dwelling, building or structure used in whole or in part for
residential purposes, including those owned or operated by the Commonwealth and where the side wall exhaust vent termination is less than
seven (7) feet above finished grade in the area of the venting, including but not limited to decks and porches, the following requirements shall
be satisfied:
1. INSTALLATION OF CARBON MONOXIDE DETECTORS. At the time of installation of the side wall horizontal vented gas fueled
equipment, the installing plumber or gasfitter shall observe that a hard wired carbon monoxide detector with an alarm and battery back-up is
installed on the floor level where the gas equipment is to be installed. In addition, the installing plumber or gasfitter shall observe that a battery
operated or hard wired carbon monoxide detector with an alarm is installed on each additional level of the dwelling, building or structure
served by the side wall horizontal vented gas fueled equipment. It shall be the responsibility of the property owner to secure the services of
qualified licensed professionals for the installation of hard wired carbon monoxide detectors
a. In the event that the side wall horizontally vented gas fueled equipment is installed in a crawl space or an attic, the hard wired carbon
monoxide detector with alarm and battery back-up may be installed on the next adjacent floor level.
b. In the event that the requirements of this subdivision can not be met at the time of completion of installation, the owner shall have a period of
thirty (30) days to comply with the above requirements; provided, however, that during said thirty (30) day period, a battery operated carbon
monoxide detector with an alarm shall be installed.
2. APPROVED CARBON MONOXIDE DETECTORS. Each carbon monoxide detector as required in accordance with the above provisions
shall comply with NFPA 720 and be ANSI/UL 2034 listed and IAS certified.
3. SIGNAGE. A metal or plastic identification plate shall be permanently mounted to the exterior of the building at a minimum height of eight
(8) feet above grade directly in line with the exhaust vent terminal for the horizontally vented gas fueled heating appliance or equipment. The
sign shall read, in print size no less than one-half (1/2) inch in size, "GAS VENT DIRECTLY BELOW. KEEP CLEAR OF ALL
OBSTRUCTIONS".
4. INSPECTION. The state or local gas inspector of the side wall horizontally vented gas fueled equipment shall not approve the installation
unless, upon inspection, the inspector observes carbon monoxide detectors and signage installed in accordance with the provisions of 248 CMR
5.08(2)(a)1 through 4.
(b) EXEMPTIONS: The following equipment is exempt from 248 CMR 5.08(2)(a)1 through 4:
1. The equipment listed in Chapter 10 entitled "Equipment Not Required To Be Vented" in the most current edition of NFPA 54 as adopted by
the Board; and
2. Product Approved side wall horizontally vented gas fueled equipment installed in a room or structure separate from the dwelling, building or
structure used in whole or in part for residential purposes.
(c) MANUFACTURER REQUIREMENTS - GAS EQUIPMENT VENTING SYSTEM PROVIDED. When the manufacturer of Product
Approved side wall horizontally vented gas equipment provides a venting system design or venting system components with the equipment, the
instructions provided by the manufacturer for installation of the equipment and the venting system shall include:
1. Detailed instructions for the installation of the venting system design or the venting system components; and
2. A complete parts list for the venting system design or venting system.
(d) MANUFACTURER REQUIREMENTS - GAS EQUIPMENT VENTING SYSTEM NOT PROVIDED. When the manufacturer of a
Product Approved side wall horizontally vented gas fueled equipment does not provide the parts for venting the flue gases, but identifies
"special venting systems", the following requirements shall be satisfied by the manufacturer:
1. The referenced "special venting system" instructions shall be included with the appliance or equipment installation instructions; and
2. The "special venting systems" shall be Product Approved by the Board, and the instructions for that system shall include a parts list and
detailed installation instructions.
(e) A copy of all installation instructions for all Product Approved side wall horizontally vented gas fueled equipment, all venting instructions,
all parts lists for venting instructions, and/or all venting design instructions shall remain with the appliance or equipmentat the completion of
the installation.
6
Regency HZ33CE Gas Fireplace
DIMENSIONS
UNIT DIMENSIONS
16"
407mm
23"
584mm
2-1/2"
[64mm]
26-1/16"
(662mm)
29-1/4"
742mm
21-3/8"
543mm
16"
(406mm)
NAILING STRIP
29-1/4"
742mm
34-9/16"
[878mm]
3"
(76mm)
26"
660mm
29-7/16"
747mm
4 SIDED FACEPLATE DIMENSIONS
MANTEL DIMENSIONS
42-5/16"
(1074mm)
47-9/16"
(1207mm)
3"
(76mm)
5-1/8"
(130mm)
5"
(127mm)
6-3/8"
(162mm)
29-9/16"
(750mm)
2"
(51mm)
Regency HZ33CE Gas Fireplace
35-1/2"
(901mm)
36-3/4"
(933mm)
21-1/2"
(545mm)
9"
(229mm)
9"
(229mm)
8-1/8"
(206mm)
52-1/8"
(1324mm)
7
INSTALLATION
IMPORTANT MESSAGE
SAVE THESE
INSTRUCTIONS
The HZ33CE™ Fireplace must be installed in
accordance with these instructions. Carefully read
all the instructions in this manual first. Consult the
"authority having jurisdiction" to determine the need
for a permit prior to starting the installation. It is the
responsibility of the installer to ensure this fireplace
is installed in compliance with manufacturers
instructions and all applicable codes.
BEFORE YOU START
Safe installation and operation of this appliance
requires common sense, however, we are required
by the Canadian Safety Standards and ANSI
Standards to make you aware of the following:
INSTALLATION AND REPAIR SHOULD
BE DONE BY AN AUTHORIZED
SERVICE PERSON. THE APPLIANCE
SHOULD BE INSPECTED BEFORE
USE AND AT LEAST ANNUALLY BY A
PROFESSIONAL SERVICE PERSON.
MORE FREQUENT CLEANING MAY
BE REQUIRED DUE TO EXCESSIVE
LINT FROM CARPETING, BEDDING
MATERIAL, ETC. IT IS IMPERATIVETHAT
CONTROL COMPARTMENTS, BURNERS
AND CIRCULATING AIR PASSAGEWAYS
OF THE APPLIANCE BE KEPT CLEAN.
DUE TO HIGH TEMPERATURES, THE
APPLIANCE SHOULD BE LOCATED
OUT OF TRAFFIC AND AWAY FROM
FURNITURE AND DRAPERIES.
WARNING: FAILURE TO INSTALL THIS
APPLIANCE CORRECTLY WILL VOID
YOUR WARRANTY AND MAY CAUSE A
SERIOUS HOUSE FIRE.
CHILDREN AND ADULTS SHOULD BE
ALERTED TO THE HAZARDS OF HIGH
SURFACE TEMPERATURES, ESPECIALLY THE FIREPLACE GLASS, AND
SHOULD STAY AWAY TO AVOID BURNS
OR CLOTHING IGNITION.
8
YOUNG CHILDREN SHOULD BE CAREFULLY SUPERVISED WHEN THEY ARE
IN THE SAME AREA AS THE APPLIANCE. TODDLERS, YOUNG CHILDREN
AND OTHERS MAY BE SUSCEPTIBLE
TO ACCIDENTAL CONTACT BURNS. A
PHYSICAL BARRIERS IS RECOMMENDED IF THERE ARE AT RISK INDIVIDUAL
IN THE HOUSE. TO RESTRICT ACCESS
TO A FIREPLACE OR STOVE, INSTALL
AN ADJUSTABLE SAFETY GATE TO
KEEP TODDLERS, YOUNG CHILDREN
AND OTHER AT RISK INDIVIDUALS OUT
OF THE ROOM AND AWAY FROM HOT
SURFACES.
CLOTHING OR OTHER FLAMMABLE
MATERIAL SHOULD NOT BE PLACED
ON OR NEAR THE APPLIANCE.
ANY SAFETY SCREEN, GUARD, OR
BARRIER REMOVED FOR SERVICING
THE APPLIANCE, MUST BE REPLACED
PRIORTO OPERATINGTHE APPLIANCE.
IF THE BARRIER BECOMES DAMAGED,
THE BARRIER SHALL BE REPLACED
WITHTHE MANUFACTURER'S BARRIER
FOR THIS APPLIANCE.
GENERAL SAFETY
INFORMATION
5. Inspect the venting system annually for blockage
and any signs of deterioration. 6. Venting terminals shall not be recessed into a
wall or siding.
7. Any safety glass removed for servicing must be
replaced prior to operating the appliance.
8. To prevent injury, do not allow anyone who is
unfamiliar with the operation to use the fireplace.
9. Wear gloves and safety glasses for protection
while doing required maintenance.
10.Be aware of electrical wiring locations in walls
and ceilings when cutting holes for termination.
11.Under no circumstances should this appliance
be modified. Parts that have to be removed for
servicing should be replaced prior to operating
this appliance.
12.Installation and any repairs to this appliance
should be done by an authorized service person. A professional service person should be
called to inspect this appliance annually. Make
it a practice to have all of your gas appliances
checked annually.
13.Do not slam shut or strike the glass door.
14.Under no circumstances should any solid fuels
(wood, paper, cardboard, coal, etc.) be used in
this appliance.
15.The appliance area must be kept clear and
free of combustible materials, (gases and other
flammable vapours and liquids).
Emissions from burning wood or gas could
contain chemicals known to the State of
California to cause cancer, birth defects or
other reproductive harm.
1. The appliance installation must conform with
local codes or, in the absence of local codes,
with the current Canadian or National Gas
Codes, CAN1-B149 or ANSI Z223.1 Installation
Codes.
2. The appliance when installed, must be electrically grounded in accordance with local codes,
or in the absence of local codes with the current
National Electrical Code, ANSI/NFPA 70 or CSA
C22.1 Canadian Electrical Code.
3. See general construction and assembly instructions. The appliance and vent should be
enclosed.
4. This appliance must be connected to the specified vent and termination cap to the outside of
the building envelope. Never vent to another
room or inside a building. Make sure that the
vent is fitted as per Venting instructions.
Regency HZ33CE Gas Fireplace
INSTALLATION
INSTALLATION
CHECKLIST
1. Locate appliance:
a) Room location (Refer to "Locating Your
Gas fireplace" section)
b) Clearances to Combustibles (Refer to
"Clearances" section)
c) Mantle Clearances (Refer to "Mantel
Clearances" section)
d) Framing & Finishing Requirements (Refer to "Framing & Finishing" section)
e) Venting Requirements (Refer to "Venting"
section)
This includes:
1. Clocking the appliance to ensure the correct
firing rate (rate noted on label), after burning
appliance for 15 minutes.
2. If required, adjusting the primary air to ensure
that the flame does not carbon. First allow
the unit to burn for 15-20 min. to stabilize.
CAUTION: Any alteration to the product that
causes sooting or carboning that results
in damage is not the responsibility of the
manufacturer.
2. Assemble Top and Side Standoffs (Refer to
"Unit Assembly Prior to Installation).
3. Slide unit into place.
LOCATING YOUR
GAS FIREPLACE
4. Install vent (Refer to "Venting Arrangement"
sections).
1. When selecting a location for your fireplace,
ensure that the clearances are met.
5. Make gas connections (Refer to "Gas Line
Installation section).
2. The appliance must be installed on a flat,
solid, continuous surface For example a
wood, metal or concrete floor or in a raised (on
the wall) application. The appliance must be
installed on a metal or wood panel extending
the full width and depth of the appliance.
6. Test the pilot (Refer to "Pilot Adjustment"
section).
7. Test Gas Pressure (Refer to "Gas Pipe Pressure Testing" section).
8. Install 4 AA batteries in the battery pack or
optional AC power adaptor.
9. Install standard and optional features. Refer
to the following sections:
a)
Optional Reflective Panels
b)
Glass Crystals or Optional Ceramic
Stones
c)
Remote Control or Wall Thermostat d)
Optional Fan Assembly
e)
Optional 4 sided Faceplate
f) Optional Mantel
10.Wall Mounted ON/OFF Switch:
Use the toggle wall switch supplied with the
manual package. Use of a “decor” switch
causes higher resistance which is a problem
on gas fireplaces.
4. This appliance is Listed for bedroom installations when used with a listed Millivolt
Thermostat. Some areas may have further
requirements, check local codes before
installation.
5. The HZ33CE Gas Fireplace is approved for
alcove installations, see "Clearances" section
for details.
6. We recommend that you plan your installation
on paper using exact measurements for
clearances and floor protection before
actually installing this appliance. Have an
authorized inspector, dealer, or installer
review your plans before installation.
Note: For vent terminations refer to "Exterior
Vent Termination Locations" section.
3. The HZ33CE Gas Fireplace can be installed
in a recessed position or framed out into the
room as in A, B, C and D. See Diagram 1.
A) Flat on Wall
Diagram 1
11.Final check.
Before leaving this unit with the customer, the
installer must ensure that the appliance is firing
correctly and operation fully explained to
customer.
Regency HZ33CE Gas Fireplace
B) Flat on Wall Corner
C) Recessed into Wall/Alcove
D) Corner
9
INSTALLATION
CLEARANCES
The clearances listed below are Minimum distances unless otherwise stated:
A major cause of chimney related fires is failure to maintain required clearances (air space) to combustible materials. It is of the greatest
importance that this fireplace and vent system be installed only in accordance with these instructions.
Caution Requirements
The top, back and sides of the fireplace are defined by
standoffs. The metal ends of the standoff may NOT
be recessed into combustible construction.
WARNING
Fire hazard is an extreme risk
if these clearances (air space) to combustible materials are not
adhered to. It is of greatest importance that this fireplace and vent
system be installed only in accordance with these instructions.
C
C
F
G
Close to Ceiling
Clearance:
A: *Front Floor Clearance (min.)
0"
Measured From:
Underside of Unit
B: *Sidewall (on one side)
9" (229mm)
Side Opening of Unit
C: *Ceiling
(room and/or alcove)
30" (762mm)
Top Opening of Unit
D: Alcove Width
84" (1219mm)
Sidewall to Sidewall (Minimum)
E: Alcove Depth
36" (914mm)
Front to Back Wall (Maximum)
F: Mantel
12" (305mm)
G:Mantel Clearances
10
Dimension
15-3/4" (400mm)
Flue Clearances
Horizontal - Top
Horiztonal - Side
Horiztonal - Bottom
Vertical (Flex Vent)
Vertical (Rigid)
2-1/2"
1-1/2"
1-1/2"
1-1/2"
1-1/4"
From Top Opening of Unit
Regency HZ33CE Gas Fireplace
INSTALLATION
MANTEL CLEARANCES
Due to the extreme heat this fireplace emits, the
mantel clearances are critical. Combustible mantel
clearances from top of front facing are shown in the
diagram on the right.
Note: Ensure the paint that is used on the mantel
and the facing is "heat resistant" or the
paint may discolour.
16
10
8
6
4
0
Note: A non-combustible mantel may be
installed at a lower height if the framing
is made of metal studs covered with a
non-combustible board.
Mantel Clearances
12
2
12" (305mm)
Drywall
7-1/2"(191mm)
14
0” - 3-1/2" (89mm)
12
10
15-3/4" (400mm)
8
6
13-3/4"(349mm)
4
Non-combustible material
11-3/4"(298mm)
3"(76mm)
Standoff
2
0
24-1/4"(616mm)
to floor
Top opening
of Unit
Side View
MANTEL LEG CLEARANCES
Combustible mantel leg clearances from side of unit as per diagram:
Top View
0-3
Side opening of Unit
6-3/4"
Allowable mantel leg projection
9"
Regency HZ33CE Gas Fireplace
11
INSTALLATION
FRAMING & FINISHING
1. There are 8 (eight) side nailing strips and one top nailing strip available on the unit. One set of four (4) are for a clean finish installation, the other set are
for a tile finish installation as they are set back 1/2" (13mm). The top nailing strip is adjustable to 1/2" (13mm).
2. Bend the required four (4) nailing strips to 90º.
3. Attach top nailing strip with one (1) screw (located at the back of the nailing strip). Adjust to required position, flush or back 1/2" and tighten screw.
Adjustable Top
Nailing Strip
Nailing strip for
Clean Finish (set
flush with unit)
Nailing strip for
Tile Finish (set
back 1/2")
Nailing strip for
Tile Finish (set
back 1/2")
Nailing strip for
Clean Finish (set
flush with unit)
1. Frame in the enclosure for the unit with framing material.
Note:When constructing the framed opening, please ensure there is access to install the gas lines when the unit is installed.
2. For exterior walls, insulate the enclosure to the same degree as the rest of the house; apply vapour barrier and drywall, as per local installation codes.
(Do not insulate the fireplace itself.)
WARNING: Failure to insulate and add vapor barriers to the inside of the exterior wall will result in operational and performance problems
including, but not limited to: excessive condensation on glass doors, poor flame package, carbon, blue flames etc. These are not product
related issues.
3. The unit does not have to be completely enclosed in a chase. You must maintain clearances from the vent to combustible materials: See "Clearances"
section. Combustible materials can be laid against the side and back standoffs and the stove base.
4. Tile Finish Option 1: Drywall may be installed onto the unit as shown below to create a surface to apply finishing materials such as tile, slate, etc. Drywall cannot extend beyond the metal surface of the unit.
5. Tile Finish Option 2: If applying a non-combustible finishing material (tile,slate,etc) the material can be installed directly onto the metal surface (clean
front) of the unit in the area shown below.
TILE FINISH
Combustible
Material
Non-combustible Material (3-1/2" x 34-9/16")
Non-combustible
Finishing Material
(ie. tile)
Supplied with Unit
Nailing Strip -1/2" back from unit face
1-1/2
(38mm)
21-3/8"
[542mm]
Ensure finished
material is
brought to lip
Non-combustible
Finishing Material
(ie. tile)
29-7/16"
747mm
12
Combustible
Material
Regency HZ33CE Gas Fireplace
INSTALLATION
IMPORTANT
Regency Fireplace Products are designed, produced, tested and certified to the highest industry standards.
The finishing of the walls surrounding your Regency Horizon Fireplace is as critical as the installation itself.
The temperatures around linear gas fireplaces are typically higher than would be acceptable for combustible materials. Your Regency Horizon Fireplace is no exception to this
rule. Therefore, the units are specified with non-combustible required materials to specific dimensions above and around the units. This is due to these areas reaching higher
temperature levels than required/acceptable for a combustible material. To obtain the best, most durable finish around your fireplace, this calls for a high level of care and attention
to the preparation and finish around this appliance, using only the highest quality materials, able to withstand the temperatures produced.
By following the installation instructions in the manual exactly, you will increase your chances of a damage free finish.
While every precaution is taken in providing the recommendations on preparation and finish, given the variations in paint quality, with temperature limits and workmanship in
application, Regency is unable to guarantee the life of the joint compounds, paint or any other finish materials or workmanship applied to or used in any application surrounding
the fireplace. This includes framing as well as finishing.
Over time natural convection from any fireplace can cause discoloration in the area directly above the appliance. Lower quality paints, under-prepared finishes, poor applications,
and any framing discrepancies or in the installation can cause this discoloration process to be expedited.
Discoloration is not the responsibility of Regency Fireplace Products. This is outwith the control of Regency Fireplace Products Ltd., therefore not covered under any part of the
warranty policy.
While discoloration is not the responsibility of Regency Fireplace Products, we believe careful attention to the recommendations provided here will result in an aesthetically
pleasing result free of issues outlined above.
Regency HZ33CE Gas Fireplace
13
INSTALLATION
CLEAN FINISH
6. If applying a non-combustible facing it may be installed over the metal surface (clean front) of the unit in the area shown below.
WOOD STUD
Combustible
Material
1/2" DRYWALL
Non-combustible Material (3-1/2" x 34-9/16")
DO NOT EXTEND
DRYWALL ONTO METAL
SURFACE OF UNIT.
NON COMBUSTIBLE BOARD SUPPLIED WITH UNIT
Supplied with Unit
Non-combustible
Finishing Material
3-1/2"
[89mm]
Nailing Strip -flush with unit
NON-COMBUSTIBLE FACING
FOR CLEAN LOOK
(ie. PAINTED FINISH)
34-9/16"
878mm
Ensure finished
material is
brought to lip
1-1/2
(38mm)
33-7/16"
[849mm]
1/2" DRYWALL
Non-combustible
Finishing Material
Combustible
Material
Combustible and Non-combustible Facing and Finishing
Materials around unit.
NOTE: The 3-1/2" x 34-9/16" non combustible material supplied with this unit can be replaced if trying to achieve a clean finish. A large piece of non combustible material (ie. 4' x 8' x 1/2") can be used to eliminate taped seams on or near unit.
7. Non-combustible material (ie. tile, slate, etc.) may be brought up to the edge of the glass door of the unit. Minimum clearances must be adhered to, this
will assure ease of glass door removal and access to the lower panel.
NOTE: Non-combustible finishing materials may be of any thickness desired.
3-1/2"
[89mm]
NON COMBUSTIBLE BOARD SUPPLIED WITH UNIT
J Style trim or metal
corner bead may be
used to finish edges
21-3/8"
[542mm]
NO FACING OR
FINISHING MATERIAL
IN THIS AREA
No Combustible
Materials in this Area
33-7/16"
[849mm]
5-3/16"
[132mm]
21-3/8"
[542mm]
2-1/2"
[64mm]
No Combustible
Materials in this Area
29-7/16"
747mm
34-9/16"
878mm
Minimum Clearances for Finishing Materials
29-7/16"
747mm
Trim materials
IMPORTANT FINISHING DETAIL NOTE:
Before placing unit into final position - it is important to know the
total thickness / height of finished hearth (tile, carpet, etc.) The base
of the fireplace, 4 sided faceplate or mantel should be level or higher
than the finished hearth height.
Note:All non-combustible facing material should butt up cleanly to the flanges around the firebox opening. Rough edges may be visible from an angle.
To maintain a clean finished edge - facing material edges
may be finished with a J-style trim or metal cornerbead (both
materials available at your local building or hardware store).
IMPORTANT: Materials used must be NON-COMBUSTIBLE.
14
Regency HZ33CE Gas Fireplace
INSTALLATION
FRAMING DIMENSIONS
NOTE: If this is an outside corner, the minimum distance between the vent
and the outside corner is 6" (15cm)
with AstroCap termination cap or 12"
(30cm) with Rigid Vent termination
cap. (For example Dura-Vent)
Framing Dimensions
Description
HZ33CE
G
Framing Width
35"(889mm)
H
Framing Height *
I
Framing Rise from Floor
0" (when not using a surround)
2" min (when using Mantel)
3-5/16" min (when using 4 sided Faceplate)
J * For Finish with Tile Surround
Framing Depth Vertical
Horizontal
22-3/4" (578mm) Vertical Rise
19-3/4" (502mm) Rigid / 16" (406mm) Flex
K
Corner Wall Length
38-15/16" (988mm)
L
Corner Facing Wall Width
55-1/2" (1410mm)
31-3/4" (806mm)
M
Framed Chase Ceiling*
36" (914mm) Rigid
32" (812mm) Flex
N
Vent Centerline Height*
30" (762mm) Rigid
26" (660mm) Flex
O
Gas Connection Height*
P
Gas Connection Inset*
7-3/16" (183mm)
Q
Gas Connection Width*
3" (76mm)
1 1/2" (38mm)
* Measured from base of unit.
Regency HZ33CE Gas Fireplace
15
INSTALLATION
VENTING INTRODUCTION
The HZ33CE uses the "balanced flue" technology Co-Axial system. The inner liner vents products of combustion to the outside while the outer
liner draws outside combustion air into the combustion chamber thereby eliminating the need to use heated room air for combustion and losing
warm room air up the chimney.
There are 5 vent systems approved for use with the HZ33CE: the Regency® Direct Vent Flex System for Horizontal Terminations only and the
Simpson Dura-Vent, Selkirk Direct-Temp, Amerivent Direct Vent and Security Secure Vent Systems for Horizontal and Vertical Terminations (see
following "Venting" Sections for more details).
Note: These flue pipes must not be connected to any other appliance.
The gas appliance and vent system must be vented directly to the outside of the building, and never be attached to a chimney serving a separate
solid fuel or gas burning appliance. Each direct vent gas appliance must use it's own separate vent system. Common vent systems are prohibited.
(See "Rigid Pipe Venting System" for more details and exceptions).
NOTE: Ensure compliance with the outside vent terminal location before cutting hole as both dimensions must be met.
16
Regency HZ33CE Gas Fireplace
INSTALLATION
EXTERIOR VENT TERMINATION REQUIREMENTS
Minimum Clearance Requirements
Canada1
USA2
A
Clearance above grade, veranda, porch, deck, or balcony
12"(30cm)
12"(30cm)
B
Clearance to window or door that may be opened
12"(30cm)
9" (23cm)
C
Clearance to permanently closed window
*
*
D
Vertical clearance to ventilated soffit located above the terminal within a horizontal distance of 2 feet (61cm)
from the center line of the terminal (check with the local code)
18"(46cm)
18"(46cm)
E
Clearance to unventilated soffit
15"(38cm)
15"(38cm)
F
Clearance to outside corner: with AstroCap Termination Cap.
6"(15cm)
6"(15cm)
Clearance to outside corner: with all other approved Termination Caps.
12"(30cm)
12"(30cm)
G
Clearance to inside corner: with AstroCap Termination Cap
6"(15cm)
6"(15cm)
Clearance to inside corner: with all other approved Termination Caps.
12"(30cm)
12"(30cm)
H
Clearance to each side of center line extended above meter/regulator assembly
36"(90cm)a
*
J
Clearance to service regulator vent outlet
36"(90cm)
*
K
Clearance to non-mechanical air supply inlet to building or the combustion air inlet to any other appliance
12"(30cm)
9" (23cm)
L
Clearance to a mechanical air supply inlet
#3' (91cm) above if within 10' (3m) horizontally.
72"(1.8m)
36"(90cm)b
M
Clearance above paved sidewalk or a paved driveway located on public property
84"(2.1m)┼
*
N
Clearance under veranda, porch, deck, or balcony
12"(30cm)‡
*
1
In accordance with current CSA B149.1, Natural Gas and Propane Installation Code
In accordance with the current ANSI Z223.1/NFPA 54, National Fuel Gas Code
A vent shall not terminate directly above a sidewalk or paved driveway which is located between two single family dwellings and serves both dwellings
‡ Permitted only if veranda, porch, deck, or balcony is fully open on a minimum of two sides beneath the floor
* Clearance in accordance with local installation codes and the requirements of the gas supplier
a 3 feet (91cm) within a height of 15 feet (4.5m) above the meter / regulator assembly
b 3 feet (91cm) above - if within 10 feet (3m) horizontally 2
┼
Regency HZ33CE Gas Fireplace
17
INSTALLATION
REGENCY® DIRECT VENT FLEX SYSTEM
Horizontal Terminations Only
This venting system, in combination with the HZ33CE-4 Direct Vent Gas Fireplace, have been tested and listed as a direct vent heater system by Warnock Hersey.
The location of the termination cap must conform to the requirements in the "Exterior Vent Terminal Locations" Section .
Regency® Direct Vent Flex Termination Kit (Part # 946-513. includes all the parts needed to install the HZ33CE with a maximum run of 2 feet. If
installing the HZ33CE-4 with a continuous vent length of more than 2 ft (.6m) to a maximum of 10 ft. (3.0m) use Kit # 946-515 (4 ft) or 946-516 (10 ft) or
see "Rigid Pipe Venting Systems" Section for alternate venting arrangements.
AstroCap Flex Kits
1
6-7/8" dia. flexible liner (kit length)
2
4" dia. flexible liner (kit length)
3
spring spacers (3.
4
thimble (2.
5
AstroCap termination cap (1.
6
screws (12.
7
tube of Mill Pac (1.
8
plated screws (8.
9
screws #8 x 1-1/2" drill point,
stainless steel (4.
Notes:
1. Liner sections should be continuous
without any joints or seams.
2. Only Flex pipe purchased from Regency®
may be used for Flex installations.
Alternate
Horizontal
Termination
Caps
MINIMUM
MINIMUM
RIGID PIPE CENTER-LINE
FLEX KIT CENTER-LINE
Wherever necessary due to
external location of cap, the
AstroCap can be replaced
with the FPI Riser Vent Termination Cap.
Note: - Unit must be raised by 1".
18
Regency HZ33CE Gas Fireplace
INSTALLATION
RIGID PIPE VENTING SYSTEMS
Horizontal or Vertical Terminations
The minimum components required for a basic
horizontal termination are:
1
1
1
1
1
AstroCap Horizontal Termination Cap
45o Elbow
Rigid Pipe Adaptor
Wall Thimble
Length of pipe to suit wall thickness
(see chart)
For siding other than vinyl, furring strips may
be used, instead of the vinyl siding standoff, to
create a level surface to mount the vent terminal.
The Terminal must not be recessed into siding.
If a Vinyl Siding Standoff is required (it must
be used with vinyl siding), measure to outside
surface of wall without siding and add 2 inches.
Vertical
Terminal
Storm Collar
Vinyl Siding
Standoff (Optional)
Flashing
Horizontal
Termination Cap
# 946-523/P
Ceiling Firestop
Wall Thimble
Adj.Pipe Length
11" - 14-5/8”
Pipe Length
Horizontal
Termination Cap
#946-523/P
90o Elbow
Vinyl Siding
Standoff (Optional)
Pipe Length
Alternate
Horizontal
Termination
Caps
Wall Thimble
Pipe Length
o
45 Elbow
Rigid Pipe Adapter
# 510-994
WARNING:
Do not combine venting components from
different venting systems.
Exception: However, use of the the AstroCapTM
and FPI Riser is acceptable with all systems.
19-3/4"
(502mm)
27"
(686mm)
Flat Wall Installation
Max.
Wall
Vent Length
Thickness (inches) Required (inches)
7 - 1/4" 6"
10 - 1/4"
9"
13 - 1/4"
12"
8 -1/4" 3" to 7" Slip
13 - 1/4"
3"
to 14-1/2 " Slip
This product has been evaluated by Intertek
for using a Rigid Pipe Adaptor in conjunction
with Duravent Direct-Vent , Selkirk Direct-Temp,
Ameri Vent Direct venting and Security Secure
Vent systems. Use of these systems with the
Rigid Pipe adaptor is deemed acceptable
and does not affect the Intertek WHI listing of
components.
When using Rigid Vent other than
Simpson Dura-Vent, 3 screws must be
used to secure rigid pipe to adaptor.
The FPI AstroCapTM and FPI Riser Vent terminal are certified for installations using FPI venting systems as well as Simpson Dura-Vent® Direct Vent,
American Metal Products Ameri Vent Direct Vent, Security Secure Vent®, Selkirk Direct-Temp. AstroCapTM is a proprietary trademark of FPI Fireplace
Products International Ltd. Dura-Vent® and Direct Vent are registered and/or proprietary trademarks of Simpson Dura-Vent Co. Inc.
Regency HZ33CE Gas Fireplace
19
INSTALLATION
4" X 6-5/8" RIGID PIPE CROSS REFERENCE CHART
4” X 6- 5/8” RIGID
CROSSall
REFERENCE
CHARTare available directly from FPI.
Components from different Manufacturers
may notPIPE
be mixed. Not
Rigid Pipe components
Components from different Manufacturers may not be mixed. Not all rigid pipe components are available directly from Regency.
Description
Simpson
Direct Vent Pro®
Selkirk
Direct Temp™
American Metal
Products®
Metal-Fab™
Sure Seal
Security
ICC Excel
Secure- Vent®
Direct
Amerivent Direct
6” Pipe Length-Galvanized
46DVA-06
4DT-6
N/A
4D6
SV4L6
TC-4DL6
6” Pipe Length-Black
46DVA-06B
4DT-6B
N/A
4D6B
SV4LB6
TC-4DL6B
7” Pipe Length-Galvanized
N/A
N/A
4D7
N/A
N/A
N/A
7” Pipe Length-Black
N/A
N/A
4D7B
N/A
N/A
N/A
9” Pipe Length-Galvanized
46DVA-09
4DT-9
N/A
N/A
N/A
N/A
9” Pipe Length-Black
46DVA-09B
4DT-9B
N/A
N/A
N/A
N/A
12” Pipe Length-Galvanized
46DVA-12
4DT-12
4D12
4D12
SV4L12
TC-4DL1
12” Pipe Length-Black
46DVA-12B
4DT-12B
4D12B
4D12B
SV4LB12
TC-4DL1B
18” Pipe Length-Galvanized
46DVA-18
4DT-18
4D18
4D18
SV4LA
TC-4DL18
18” Pipe Length-Black
46DVA-18B
4DT-18B
4D18B
4D18B
SV4LA
TC-4DL18B
24” Pipe Length-Galvanized
46DVA-24
4DT-24
4D24
4D24
SV4L24
TC-4DL2
24” Pipe Length-Black
46DVA-24B
4DT-24B
4D24B
4D24B
SV4LB24
TC-4DL2B
36” Pipe Length-Galvanized
46DVA-36
4DT-36
4D36
4D36
SV4L36
TC-4DL3
36” Pipe Length-Black
46DVA-36B
4DT-36B
4D36B
4D36B
SV4LB36
TC-4DL3B
48” Pipe Length-Galvanized
46DVA-48
4DT-48
4D48
4D48
SV4L48
TC-4DL4
48” Pipe Length-Black
46DVA-48B
4DT-48B
4D48B
4D48B
SV4LB48
TC-4DL4B
60” Pipe Length-Galvanized
46DVA-60
4DT-60
N/A
N/A
N/A
N/A
60” Pipe Length-Black
46DVA-60B
4DT-60B
N/A
N/A
N/A
N/A
Adjustable Length 3”-10”-Galvanized
N/A
N/A
N/A
4DAL
N/A
TC-4DLT
Adjustable Length 3”-10”-Black
N/A
N/A
N/A
4DALB
N/A
TC-4DLTB
Adjustable Length 7”-Galvanized
N/A
N/A
4D7A
N/A
N/A
N/A
Adjustable Length 7”-Black
N/A
N/A
4D7AB
N/A
N/A
N/A
Extension Pipe 8-1/2”-Galvanized
46DVA-08A
N/A
N/A
N/A
N/A
N/A
Extension Pipe 8-1/2”-Black
46DVA-08AB
N/A
N/A
N/A
N/A
N/A
Adjustable Length 12”-Galvanized
N/A
N/A
4D12A
N/A
SV4LA12
N/A
Adjustable Length 12”-Black
N/A
N/A
4D12A
N/A
SV4LBA12
N/A
Extension Pipe 16”-Galvanized
46DVA-16A
N/A
N/A
N/A
N/A
N/A
Extension Pipe 16”-Black
46DVA-16AB
N/A
N/A
N/A
N/A
N/A
45º Elbow-Galvanized
46DVA-E45
4DT-EL45
4D45L
N/A
N/A
TE-4DE45
45º Elbow-Black
46DVA-E45B
4DT-EL45B
4DT-EL45B
N/A
N/A
TE-4DE45B
45º Elbow Swivel-Galvanized
See 46DVA-E45
N/A
N/A
4D45L
SV4E45
N/A
45º Elbow Swivel-Black
See 46DVA-E45B
N/A
N/A
4D45LB
SV4EB45
N/A
90º Elbow-Galvanized
46DVA-E90
4DT-EL90S
4DT-EL90S
N/A
N/A
TE-4DE90
90º Elbow-Black
46DVA-E90B
4DT-EL90SB
4DT-EL90SB
N/A
SV4EBR90-1
TE-4DE90B
90º Elbow, Swivel-Galvanized
See 46DVA-E90
N/A
N/A
4D90L
SV4E90-1
N/A
90º Elbow, Swivel-Black
See 46DVA-E90B
N/A
N/A
4D90LB
SV4EB90-1
N/A
90º Starter Elbow, Swivel-Galvanized
N/A
N/A
N/A
4D90A
N/A
N/A
Adaptor*
N/A
N/A
N/A
4D90L
N/A
N/A
Ceiling Support
N/A
4DT-CS
4DFSP
4DSP
SV4SD
TE-4DE45
Cathedral Support Box
46DVA-CS
4DT-CSS
4DRSB
4DRS
SV4CSB
TE-4DE45B
Wall Support/Band
46DVA-WS
4DT-WS/B
4DWS
4DWS
SV4BM
N/A
Offset Support
46DVA-ES (N/A - FPI)
4DT-OS
N/A
N/A
SV4SU
N/A
Wall Thimble-Black
46DVA-WT
4DT-WT
4DWT
4DWT
SV4RSM
TE-4DE90
Wall Thimble Support/Ceiling Support
46DVA-DC
N/A
N/A
N/A
SV4PF
TE-4DE90B
Firestop Spacer
46DVA-FS
4DT-FS
4DFSP
4DFS
SV4BF
N/A
Trim Plate-Black
N/A
4DT-TP
4DFPB
4DCP
SV4LA
N/A
20
Regency HZ33CE Gas Fireplace
INSTALLATION
Description
Selkirk
Simpson
American Metal
Products®
Direct Temp™
Direct Vent Pro®
Metal-Fab™
Sure Seal
Security
ICC Excel
Secure- Vent®
Direct
Amerivent Direct
Attic Insulation Shield 12”
46DVA-IS N/A@ FPI
N/A
4DAIS12
N/A
SV4RSA
N/A
Attic Insulation Shield - Cold Climates 36”
N/A
N/A
4DAIS12
N/A
N/A
TM-4AS
Basic Horizontal Termination Kit (A)
Disc.
4DT-HKA
4DHTK2
4DHTKA
SV-SHK
N/A
Horizontal Termination Kit (B)
46DVA-KHA
4DT-HKB
4DHTK1
4DHTKB
SV-HK
N/A
Vertical Termination Kit
Disc.
4DT-VKC
4DHTK
4DHTK
SV-FK
N/A
High Wind Vertical Cap
46DVA-VCH
N/A
N/A
N/A
N/A
TM-4VT
High Wind Horizontal Cap
46DVA-HC
N/A
N/A
N/A
N/A
TM-4DHT
(Changed Components)
Horizontal Square Termination Cap
See 46DVA-HC
4DT-HHC
4DHC
4DHT
SV4CHC-1
TM-4HT
Vertical Termination Cap
46DVA-VC
4DT-HVC
4DVC
4DVT
SV4CGV-1
TM-4VT
Storm Collar
46DVA-08A
4DT-SC
4DSC
4DSC
SV4FC
TM-SC
Adjustable Flashing 0/12-6/12
46DVA-F6
4DT-ST14
4D12S
4DST14
SV4STC14
TF-4FA
Adjustable Flashing 6/12-12/12
46DVA-FLA
4DT-ST36
4D36S
4DST36
SV4STC36
TF-4FB
Vinyl Siding Standoff
46DVA-VSS
4DT-VS
N/A
4DVS
SV4VS
TM-VSS
Vinyl Siding Shield Plate
N/A
4DT-VSP
N/A
N/A
SV4VS
N/A
Snorkel Termination 14”
46DVA-SNKL
N/A
N/A
N/A
N/A
TM-4ST14
Snorkel Termination 36”
N/A
N/A
N/A
N/A
N/A
TM-4ST36
Restrictor Disk
N/A
N/A
N/A
N/A
N/A
TM-4DS
Extended Vertical Termination Cap
N/A
N/A
N/A
N/A
N/A
N/A
Chimney Conversion Kit A (USA only)
46DVA-KCA
N/A
N/A
N/A
N/A
TM-4CA6
Chimney Conversion Kit B (USA only)
46DVA-KCB
N/A
N/A
N/A
N/A
TM-4CA7
Chimney Conversion Kit C (USA only)
46DVA-KCC
N/A
N/A
N/A
N/A
TM-4CA8
Chimney Conversion Kit Masonry
(USA only)
46DVA-KMC
N/A
N/A
N/A
N/A
N/A
Wall Firestop
46DVA-WFS
N/A
N/A
N/A
N/A
TM-4TR
Colinear Flex Connectors
46DVA-ADF
N/A
N/A
N/A
N/A
N/A
FPI
946-506/P
Vent Guard (Optional) for AstroCap
946-205
Vinyl Siding Shield for Riser Vent Terminal
510-994
Rigid Pipe Adaptor (Must use with all rigid piping)
946-208/P
Vent Guard (Optional) for Riser Vent Terminal
640-530/P
Riser Vent Terminal
946-523/P
AstroCap Horizontal Cap
946-605
Starter Collar Increaser 4” x 6-5/8” to 5” x 8”
946-206
Vinyl Siding Standoff for AstroCap
Note: When using Metal-Fab Sure Seal Rigid Piping - please note that the Adaptor (4DDA) must be used in conjunction with FPI Rigid Pipe Adaptor (510-994).
Offset Pipe Selection: Use this table to determine offset pipe lengths.
Pipe Length
(L)
4” x 6-5/8” Venting
Run (X)
Rise (Y)
For specific instructions on venting components - visit the
manufacturers website listed below.
0” (0mm)
4-7/8” (124mm)
13-7/8” (340mm)
Simpson Direct Vent Pro: www.duravent.com
6” (152mm)
8” (203mm)
16-1/2” (419mm)
Selkirk Direct-Temp: www.selkirkcorp.com
9” (229mm)
10-1/8” (257mm)
18-5/8” (473mm)
American Metal Products: www.americanmetalproducts.com
12” (305mm)
12-1/4” (311mm)
20-3/4” (527mm)
Metal-Fab Sure Seal: www.mtlfab.com
24” (610mm)
20-5/8” (524mm)
29-1/8” (740mm)
Security Secure Vent: www.securitychimneys.com
36” (914mm)
29” (737mm)
37-1/2” (953mm)
Industrial Chimney Company: www.icc-rsf.com
48” (1219mm)
37-7/16” (951mm)
45-15/16” (1167mm)
Note: Horizontal runs of vent must be level, or have a 1/4” rise for every 1 foot of run towards the termination.
Never allow the vent to run downward - this could cause high temperatures and may present a possible fire hazard.
Regency Fireplace Products . 6988 Venture St. . Delta, BC . Canada . V4G 1H4 . 604-946-5155 . www.regency-fire.com
Regency HZ33CE Gas Fireplace
21
INSTALLATION
RIGID PIPE VENTING ARRANGEMENTS
Vertical Terminations
(Propane & Natural Gas)
The shaded area in the diagram shows all allowable combinations of straight vertical and offset to vertical terminations, using one 90o elbow, with rigid pipe
vent systems for Propane and Natural Gas.
•
•
•
•
Unit must be raised 1".
Firestops are required at each floor level and whenever passing through a wall.
Maintain clearances to combustibles.
Vent must be supported at offsets.
Note: Must use optional rigid pipe adapter when using rigid vent systems (Part # 510-994..
22
Regency HZ33CE Gas Fireplace
INSTALLATION
VERTICAL TERMINATION
WITH CO-LINEAR FLEX SYSTEM
Masonry chimneys may take various contours which the flexible liner will accommodate. However,
keep the flexible liner as straight as possible, avoid unnecessary bending.
THE APPLIANCE MUST NOT BE
CONNECTED TO A CHIMNEY FLUE
SERVING A SEPARATE SOLID FUEL
BURNING APPLIANCE.
The Air Intake pipe must be attached to the inlet air collar of the termination cap.
This appliance is designed to be attached to
two 3" (76mm) co-linear aluminium flex running
the full length of the chimney. See the "Venting
Arrangements - Vertical Terminations" Section
for minimum and maximum heights.
Co-linear DV
Vertical Termination
Cap # 946-529
A maximum
of two certified
joiner kits
may be used
per length.
#948-305
35 ft (11m)
Required Parts:
Part #
Description
946-529
Co-linear DV Vertical
Termination Cap
948-305
3" Flex - 35 ft.
946-563
Co-Axial to Co-Linear Adapter Kit
which contains the following:
Co-linear Flex Adapter Outer Pipe
Inner Pipe Adapter
510-994
Rigid Pipe Adaptor
46DVA-E45 45o Elbow
Alternate Approved Caps
46DVA-VC Vertical Termination Cap
46DVA-VCH High Wind Cap
46DVAGK 3" Co-linear Adapter with flashing
Flex Liner
Exhaust
Flue
Outer
Pipe
with Kit#
946-563
Air Intake
Pipe Length
Co-Linear
Flex
Adapter
with Kit#
946-563
Rigid Pipe Adaptor
# 510-994
45o Elbow
Inner Pipe
Adapter
with Kit#
946-563
Regency HZ33CE Gas Fireplace
23
INSTALLATION
VENTING ARRANGEMENTS - VERTICAL TERMINATIONS
with Co-linear Flex System for both
Residential & Manufactured Homes
into Masonry Fireplaces
30' (9.1m) Max.
8' (2.4m) Min.
30”
(762mm)
30”
(762mm)
Floor
Floor
Horizontal Distance (Feet)
Vertical Height (feet)
8' (2.4m) Min.
30' (9.1m) Max.
30
2’ (51mm) max.
Vertical Height (feet)
8' (2.4m) Min.
30' (9.1m) Max.
30
30”
(762mm)
Vertical Height (feet)
30
Horizontal Distance (Feet)
Horizontal Distance (Feet)
The shaded area in the diagrams show
the allowable vertical terminations.
24
Regency HZ33CE Gas Fireplace
INSTALLATION
RIGID PIPE VENTING ARRANGEMENTS
Horizontal Terminations
REGENCY® DIRECT VENT SYSTEM (FLEX)
(Propane & Natural Gas)
This diagram shows all allowable combinations of vertical runs with horizontal terminations, using one 45o and one 90o elbow (two 45o elbows equal one 90o
elbow).
Note: Must use optional rigid pipe adaptor (Part # 510-994. when using rigid pipe vent systems. (Refer "Rigid Pipe Venting Systems" Section)
0
2
Horizontal (Feet)
4
6
8
10
12
14
16
18
20
16
14
Vertical Height (Feet)
12
10
8
A vent guard should be used whenever the
termination is lower than the specified minimum
or as per local codes.
6
4
30” (762mm) / 26” (660mm) when using flex
Minimum
Height
Requirement
2
8"(0.2m)
0
2’ (0.6m)
• Maintain clearances to combustibles.
• Horizontal vent must be supported every 3 feet.
• Firestops are required at each floor level and whenever passing through a wall.
Minimum
Simpson Dura-Vent Center-Line
Regency HZ33CE Gas Fireplace
Note: Regency® Direct Vent System (Flex)
is only approved for horizontal
terminations.
Minimum
Flex Kit Center-Line
25
INSTALLATION
Horizontal Venting with Two (2. 90o Elbows
Horizontal Venting with Three (3. 90o Elbows
One 90o elbow = Two 45o elbows.
Option
V
H + H1
A)
1' Min.
3' Max.
B)
2' Min.
4' Max.
C)
3' Min.
5' Max.
D)
4' Min.
6' Max.
E)
5' Min.
7' Max.
F)
6' Min.
8' Max.
One 90o elbow = Two 45o elbows.
With these options, maximum
total pipe length is 30 feet
with minimum of 6 feet total
vertical and maximum 8 feet
total horizontal.
Option
H
V
H+H1+H2
A)
1' Max.
1' Min.
3' Max.
B)
2' Max.
3' Min.
5' Max.
C)
3' Max.
5' Min.
6' Max.
Please note minimum 1
foot between 90o elbows is
required.
D)
4' Max.
7' Min.
7' Max.
E)
5' Max.
9' Min.
8' Max.
F)
6' Max.
11' Min.
9' Max.
With these options,
maximum total pipe
length is 30 feet with
minimum of 11 feet
total ver tical and
maximum 9 feet total
horizontal.
Please
note
minimum 1 foot
o
between 90 elbows
is required.
Horizontal Venting with Two (2. 90o Elbows
One 90o elbow = Two 45o elbows.
26
Option
H
V
H+H1
A)
1' Max.
1' Min.
3' Max.
B)
2' Max.
2' Min.
5' Max.
C)
3' Max.
4' Min.
6' Max.
D)
4' Max.
6' Min.
7' Max.
E)
5' Max.
8' Min.
8' Max.
With these options,
maximum total pipe
length is 30 feet with
minimum of 8 feet total
vertical and maximum
8 feet total horizontal.
Please note minimum
1 foot between 90o
elbows is required.
Regency HZ33CE Gas Fireplace
INSTALLATION
Horizontal Venting with Three (3. 90o Elbows
One 90o elbow = Two 45o elbows.
Option
V
H
V+V1
H+H1
A)
2' Min.
1' Max.
3' Min.
4' Max.
B)
3' Min.
2' Max.
4' Min.
5' Max.
C)
4' Min.
3' Max.
6' Min.
6' Max.
D)
5' Min.
4' Max.
8' Min.
7' Max.
E)
6' Min.
5' Max.
10' Min.
8' Max.
F)
7' Min.
6' Max.
12' Min.
9' Max.
With these options,
maximum total pipe
length is 30 feet with
minimum of 12 feet
total ver tical and
maximum 9 feet total
horizontal.
Please
note
minimum 1 foot
o
between 90 elbows
is required.
Vertical Venting with Two (2. 90o Elbows
Vertical Venting with Two (2. 90o Elbows
One 90 elbow = Two 45 elbows.
o
Option
V
H
o
V+V1
A)
1' Min. 4' Max.
2' Min.
B)
2' Min. 5' Max.
3' Min.
C)
3' Min. 6' Max.
4' Min.
D)
4' Min. 7' Max.
5' Min.
E)
5' Min. 8' Max.
6' Min.
With these options,
maximum total pipe
length is 30 feet with
minimum of 6 feet total
vertical and maximum 8
feet total horizontal.
Please note minimum
1 foot between 90 o
elbows is required.
One 90o elbow = Two 45o elbows.
Option
H + H1
V
A)
2' Max.
2' Min.
B)
3' Max.
3' Min.
C)
4' Max.
4' Min.
D)
5' Max.
5' Min.
E)
6' Max.
6' Min.
With these options, maximum
total pipe length is 30 feet
with minimum of 6 feet total
vertical and maximum 6 feet
total horizontal.
Please note minimum 1
foot between 90o elbows is
required.
For additional vertical venting with
2 x 90o elbows, refer to "Rigid Pipe
Venting Arrangements" Section.
Regency HZ33CE Gas Fireplace
27
INSTALLATION
Vertical Venting with Three (3. 90o Elbows
One 90o elbow = Two 45o elbows.
Option
A)
B)
C)
D)
E)
H
1' Max.
2' Max.
3' Max.
4' Max.
5' Max.
V
H + H1
1' Min. 3' Max.
2' Min. 4' Max.
3' Min.' 5' Max.
4' Min. 6' Max.
5' Min. 7' Max.
V + V1
3' Min.
5' Min.
7' Min.
9' Min.
11' Min.
With these options, max. total
pipe length is 30 feet with min.
of 11 feet total vertical and
max. 7 feet total horizontal.
Please note min. 1 foot
between 90 o elbows is
required.
Vertical Venting with Three (3. 90o Elbows
One 90o elbow = Two 45o elbows.
28
Option
A)
B)
C)
D)
E)
F)
V
2' Min.
3' Min.
4' Min.
5' Min.
6' Min.
7' Min.
H + H1
3' Max.
4' Max.
5' Max.
6' Max.
7' Max.
8' Max.
V + V1 With these options, max. total
4' Min. pipe length is 30 feet with min.
6' Min. of 10 feet total vertical and
7' Min. max. 8 feet total horizontal.
Please note min. 1 foot
8' Min. between 90 o elbows is
9' Min. required.
10' Min.
Regency HZ33CE Gas Fireplace
INSTALLATION
UNIT INSTALLATION WITH HORIZONTAL TERMINATION
Install the vent system according to the
manufacturer's instructions included with the
components.
1. Set the unit in its desired location. Check
to determine if wall studs or roof rafters
are in the way when the venting system is
attached. If this is the case, you may want
to adjust the location of the unit. Rough in
the gas preferably on the right side of the
unit and the electrical (junction block is on
the left side) on the left.
2. Direct Vent pipe and fittings are designed with
special twist-lock connections to connect the
venting system to the appliance flue outlet. A
twist-lock appliance adaptor is an available
option that must be used in conjunction with
the Simpson Dura-Vent Direct Vent system.
3. Put a bead of silicone inside the outer section
of the adapter and a bead of Fireplace Mate
on the inner collar. Slip the adapter over the
existing inner and outer flue collar and fasten
to the outer collar only with the 3 supplied
screws (drilling pilot holes will make this
easier). Level the fireplace and fasten it to
the framing using nails or screws through
the nailing strips.
4. Assemble the desired combination of pipe
and elbows to the appliance adaptor and
twist-lock for a solid connection.
Note:
a) Twist-lock procedure: Four indentations,
located on the female ends of pipes and
fittings, are designed to slide straight
onto the male ends of adjacent pipes
and fittings, by orienting the four pipe
indentations so they match and slide
in to the four entry slots on the male
ends, Dia. 1. Push the pipe sections
completely together, then twist-lock
one section clockwise approximately
one-quarter turn, until the two sections
are fully locked. The female locking lugs
will not be visible from the outside, on
the Black Pipe or fittings. They may be
located by examining the inside of the
female ends. NOTE: For best results and optimum
Diagram 1
performance with each approved venting
system, it is highly recommended to apply
“Mill-Pac” sealant (supplied) to every inner pipe connection. Failure to do so may
result in drafting or performance issues not
covered under warranty. Silicone (red RTV)
is optional.
b) Horizontal runs of vent must be
Regency HZ33CE Gas Fireplace
supported every three feet. Wall straps
are available for this purpose.
Diagram 2a
Riser Vent
Termination
5. Mark the wall for a 10" x 10" square hole.
The center of the square hole should line
up with the centerline of the horizontal pipe.
Cut and frame the 10 inch square hole
in the exterior wall where the vent will be
terminated. If the wall being penetrated is
constructed of non-combustible material, i.e.
masonry block or concrete, a 7"(178mm)
diameter (7-1/2"(191mm) dia. for flex) hole
is acceptable.
Note:
a) The horizontal run of vent must be level,
or have a 1/4 inch rise for every 1 foot
of run towards the termination. Never
allow the vent to run downward. This
could cause high temperatures and may
present the possibility of a fire.
b) The location of the horizontal vent
termination on an exterior wall must meet
all local and national building codes,
and must not be blocked or obstructed. See "Exterior Vent Terminal Locations"
Section.
c) Snorkel Terminations:
For installations requiring a vertical rise
on the exterior of the building, 14-inch
and 36-inch tall Snorkel Terminations
and the Riser Vent as shown in
Dia. 2 & 2a are available. Follow the
same installation procedures as used
for standard Horizontal Termination.
NEVER install the snorkel upside down.
Min. 6-1/4"*
(159mm)
If the Snorkel Termination must be
installed below grade, i.e. basement
application, proper drainage must
be provided to prevent water from
entering the Snorkel Termination. Refer
to Snorkel Installation instructions for
details. Do not attempt to enclose the
Snorkel within the wall, or any other
type of enclosure.
6. The arrow on the vent cap should
be pointing up. Insure that the 1-1/2"
clearances to combustible materials are
maintained (Dia. 3.. Install the termination
cap. AstroCapTM or all other approved
Horizontal Termination Caps may be used.
The four wood screws provided should
be replaced with appropriate fasteners for
stucco, brick, concrete, or other types of
Below Grade Snorkel Installation
Diagram 3
sidings.
Diagram 2
*As specified in CGA B149 Installation Code.
Local codes or regulations may require different
clearances.
Note: If installing termination on a siding
covered wall, a vinyl siding standoff
or furring strips must be used to
ensure that the termination is not
recessed into the siding.
7. Before connecting the horizontal run of
vent pipe to the vent termination, slide the
Wall Thimble (Part # 620-926. over the vent
pipe.
29
INSTALLATION
8. Slide the appliance and vent assembly
towards the wall carefully inserting the
vent pipe into the vent cap assembly. It is
important that the vent pipe extends into the
vent cap sufficient distance so as to result
in a minimum pipe overlap of 1-1/4 inches.
Secure the connection between the vent
pipe and the vent cap 3 sheet metal screws.
elbows. Ensure that all pipes and elbow
connections are in the fully twist-locked
position and sealed.
5. Cut a hole in the roof centered on the small
Diagram 4
9. Install wall thimble in the center of the
10" square and attach with wood screws
(Diagram 4..
NOTE: For best results and optimum
performance with each approved venting
system, it is highly recommended to apply
“Mill-Pac” sealant (supplied) to every inner pipe connection. Failure to do so may
result in drafting or performance issues not
covered under warranty. Silicone (red RTV)
is optional.
Diagram 4
UNIT INSTALLATION
WITH VERTICAL
TERMINATION
drilled hole placed in the roof in Step 2. The
hole should be of sufficient size to meet
the minimum requirements for clearance
to combustibles of 1-1/2". Slip the flashing
under the shingles (shingles should overlap
half the flashing) as per Diagram 3.
6. Continue to assemble pipe lengths.
3. A Firestop spacer must be installed in the
floor or ceiling of every level. To install the
Firestop spacer in a flat ceiling or wall, cut
a 10 inch square hole. Frame the hole as
shown in Diagram 2 and install the firestop.
4. Assemble the desired lengths of pipe and Diagram 2
30
locking it.
Note: Any closets or storage spaces, which
the vent passes through must be
enclosed.
1. Maintain the 1-1/2" clearances (air spaces) to
combustibles when passing through ceilings,
walls, roofs, enclosures, attic rafter, or other
nearby combustible surfaces. Do not pack
air spaces with insulation. Check "Venting"
Sections for the maximum
vertical rise of the venting system
and the maximum horizontal
offset limitations.
2. Set the gas appliance in its
desired location. Drop a plumb
bob down from the ceiling to
the position of the appliance
flue exit, and mark the location
where the vent will penetrate the
ceiling. Drill a small hole at this
point. Next, drop a plumb
bob from the roof to the
hole previously drilled in
the ceiling, and mark the
spot where the vent will
Diagram 1
penetrate the roof.
Roof Pitch Minimum Vent Height
Feet Meters
flat to 7/12
2
0.61
over 7/12 to 8/12
2
0.61
over 8/12 to 9/12
2
0.61
over 9/12 to 10/12
2.5
0.76
over 10/12 to 11/12
3.25
0.99
over 11/12 to 12/12
4
1.22
over 12/12 to 14/12
5
1.52
over 14/12 to 16/12
6
1.83
over 16/12 to 18/12
7
2.13
over 18/12 to 20/12
7.5
2.29
over 20/12 to 21/12
8
2.44
GAS LINE
INSTALLATION
Diagram 3: The upper half of the flashing is
installed under the roofing material and not
nailed down until the chimney is installed.
This allows for small adjustments.
Note: If an offset is necessary in the attic to
avoid obstructions, it is important to
support the vent pipe every 3 feet, to
avoid excessive stress on the elbows,
and possible separation. Wall straps
are available for this purpose.
Galvanized pipe is desirable above the roof line
due to its higher corrosion resistance. Continue
to add pipe sections through the flashing until
the height of the vent cap meets the minimum
height requirements specified in Dia. 4 or local
codes. Note that for steep roof pitches, the
vertical height must be increased. A poor
draft, or down drafting can result from high
wind conditions near big trees or adjoining
roof lines, in these cases, increasing the
vent height may solve the problem.
7. Ensure vent is vertical and secure the base
of the flashing to the roof with roofing rails,
slide storm collar over the pipe section and
seal with a mastic.
8. Install the vertical termination cap by twist-
The gas line is brought through the right side of
the appliance. The gas valve is situated on the
right hand side of the unit and the gas inlet is on
the right hand side of the valve.
The gas line connection may be made of rigid
pipe, copper pipe or an approved flex connector.
(If you are using rigid pipe, ensure that the valve
can be removed for servicing.) Since some
municipalities have additional local codes it is
always best to consult with your local authorities
and the CAN/CGA B149 installation code.
For USA installations follow local codes and/or the
current National Fuel Gas Code, ANSI Z223.1.
When using copper or flex connectors use only
approved fittings. Always provide a union so that
gas lines can be easily disconnected for servicing.
Flare nuts for copper lines and flex connectors
are usually considered to meet this requirement.
Important: Always check for gas leaks with a
soap and water solution or gas leak detector.
Do not use open flame for leak testing.
Regency HZ33CE Gas Fireplace
INSTALLATION
PILOT ADJUSTMENT
Periodically check the pilot flames. Correct
flame pattern has two strong blue flames:
1 flowing around the flame sensor and 1
flowing across the burner (it does not have
to be touching the burner).
Burner
Flame Sensor
HZ33CE-NG System Data
Conversion Kit# 434-972 (NG to LP)
For 0 to 4500 feet altitude
Burner Inlet Orifice Sizes: #47
Max. Input Rating 17,000 Btu/h
Min. Input Rating 12,000 Btu/h
Supply Pressure
min.5.0" w.c.
Manifold Pressure
(High) 3.5"+/- 0.3" w.c.
Pilot
Ignitor
Note: If you have an incorrect flame pattern,
contact your Regency® dealer for
further instructions.
Incorrect flame pattern will have small,
probably yellow flames, not coming into
proper contact with the rear burner or flame
sensor. HIGH ELEVATION
HZ33CE-LP System Data
For 0 to 4500 feet altitude
Burner Inlet Orifice Sizes: #56
Max. Input Rating 1 5 , 0 0 0 B t u / h Min. Input Rating 1 2 , 5 0 0 B t u / h Supply Pressure min.11.0" w.c.
Manifold Pressure
(High)
10"+/- 0.4"w.c.
This unit is approved in Canada for altitude to
4500 ft. (CAN/CGA-2.17-M91.. For Natural Gas
installations above 4500 ft. follow current CAN/
CGA-B149.1.
GAS PIPE PRESSURE
TESTING
The appliance must be isolated from the gas
supply piping system by closing its individual
manual shut-off valve during any pressure
testing of the gas supply piping system at test
pressures equal to or less than 1/2 psig. (3.45
kPa). Disconnect piping from valve at pressures
over 1/2 psig.
The manifold pressure is controlled by a regulator
built into the gas control, and should be checked
at the pressure test point.
Note: To properly check gas pressure, both
inlet and manifold pressures should
be checked using the valve pressure
ports on the valve.
1. Make sure the valve is in the "OFF" position.
2. Loosen the "IN" and/or "OUT" pressure tap(s),
turning counterclockwise with a 1/8" wide flat
screwdriver.
3. Attach manometer to "IN" and/or "OUT"
pressure tap(s) using a 5/16" ID hose.
4. Light the pilot and turn the valve to "ON"
position.
5. The pressure check should be carried out
with the unit burning and the setting should
be within the limits specified on the safety
label.
6. When finished reading manometer, turn
off the gas valve, disconnect the hose and
tighten the screw (clockwise) with a 1/8" flat
screwdriver. Note: Screw should be snug,
but do not over tighten.
886 S.I.T. VALVE DESCRIPTION
4
1.
2.
3.
4.
5.
6.
7.
3
Manual high/low adjustment
Pilot adjustment
Outlet Pressure Tap
Inlet Pressure Tap
Pilot Outlet
Main Gas Outlet
Main Gas Inlet
7
2
1
5
6
Regency HZ33CE Gas Fireplace
31
HZ33CE
INSTALLATION
Conversion
from NG toFROM
LPG NG TO LP
CONVERSION
KIT# 434-972
for HZ33CE
using
NOVA
Gas
Valve
For HZ33CE
usingSIT
SIT 886
886 NOVA
Gas
Valve
THIS CONVERSION
BE DONE BY MUST
A QUALIFIED
GAS FITTER
IF IN DOUBT DO
NOTFITTER
DO THIS CONVERSION !!
THISMUST
CONVERSION
BE DONE
BY A QUALIFIED
GAS
IF IN DOUBT DO NOT DO THIS CONVERSION !!
Each Kit contains one LPG
Conversion Kit # 434-972
3.
Remove 2 screws in location shown in
below - slide burner to the right then lift
out. (See Diagram 2)
6.
LPG Conversion Kit Contains:
Qty. Part #
Description
1
904-241
Burner Orifice #56
1
918-590
Decal "Converted to
LPG"
1
908-528
Red "LPG" label
1
904-529
5/32" Allen Key
1
910-101
LPG Injector
(Pilot Orifice)
1
911-009
Hi/Lo Conversion LP
1
919-126
Instruction Sheet
Installation of the LPG
Conversion Kit:
1. Shut off the gas supply
2. a) Remove the glass door.
Remove burner orifice with a 1/2"
wrench and discard. Use another
wrench to hold on to the elbow below
the orifice.
Diagram 5
Diagram 2
4. Pull off the pilot cap to expose the pilot
orifice.
b) Remove the Glass Crystals or
Ceramic Stones. Also remove
Inner Panels - if installed.
Burner Orifice
7.
Install the new burner orifice stamped
#56.
8.
Remove regulator and discard. Install Hi/
Lo pressure regulator onto the valve with
2 screws as shown below.
c) Remove the six (6) screws in locations
shown below to remove burner tray.
Diagram 3
5.
Unscrew the pilot orifice with the Allen
key and replace with the LPG pilot
orifice in the kit and replace pilot cap.
Diagram 6
9. Attach the label “This unit has been
converted to LPG” near or on top of the
serial # decal
10. Replace yellow “NG” label with red
“LPG” label
11. Reverse steps 2 - 1.
Diagram 1
12. Check for gas leaks.
13. Check inlet and outlet pressures.
14. Check operation of flame control.
Diagram 4
919-126
32
1
Installer Notice:
These instructions must be left
with the appliance
02/23/12
Regency HZ33CE Gas Fireplace
P33E / P33SE
/ P36E
INSTALLATION
GT REMOTE
REMOTE INSTALLATION
INSTALLATION
GT
1) Shut off the gas supply and disconnect all power to the unit.
8) Plug in receiver DC supply wire - as shown below.
2) Remove the louvers, bay door or faceplate if installed.
3) Disconnect battery pack - located on the floor of the unit, as shown
below and discard.
9) Install 4 - AA batteries into the receiver, ensure correct polarity.
4) Remove DFC (digital firebox control box) from the floor of the unit.
10) Plug receiver wires into the back of the receiver and bundle wires
with the wire clip as shown below.
5)
Disconnect wire harness, ground wire and spark wire from DFC.
See attached wiring diagram for details.
Wire Clip
11) Install the heat shield to the receiver with two screws and attach to
the floor of the unit with a velcro pad.
6) Identify wires in the GT remote wiring harness.
(see wiring diagram.)
Heat Shield
7) Connect the TPTH and TH wires - green to green and white to
white as shown below. See attached wiring diagram for details.
TPTH
(white)
TH
(green)
12) Reverse steps 5 and 4.
13) Match the remote control to the receiver - see remote control
instructions.
14) Reverse steps 2 and 1.
15) Check to ensure there are no gas leaks.
Regency HZ33CE Gas Fireplace
918-857
33
1
10/13/09
INSTALLATION
P33E / P33SE / P36E
GTM REMOTE INSTALLATION
GTM REMOTE INSTALLATION
6) Identify wires in the GTM/GTMF remote wiring harness.
(see wiring diagram.)
1) Shut off the gas supply and disconnect all power to the unit.
2) Remove the louvers, bay door or faceplate if installed.
7) Connect the TPTH and TH wires - green to green and white to
white as shown below.
3) Disconnect battery pack - located on the floor of the unit, as shown
below and discard.
TPTH
TH
8) Plug in receiver DC supply wire - as shown below.
4) Remove DFC (digital firebox control box) from the floor of the unit.
9) Remove the hi/lo knob if installed by removing 2 screws as
shown below.
5) Disconnect wire harness, ground wire and spark wire from DFC.
DFC
34
918-858a
Regency HZ33CE Gas Fireplace
1
09/16/09
P33E / P33SE / P36E
INSTALLATION
10) Install the stepper motor in the same location the hi/lo knob was
removed from - with 2 screws as shown below.
15) Install 4-AA batteries into the receiver.
16) Bundle all wires together and clip with supplied wire clip - as
shown below.
11) Remove the receiver if installed - unplug the motor wire from the
back of the receiver - as shown below.
17) Install the heat shield to the receiver with two screws and attach
to the floor of the unit with a velcro pad - also peel off paper on
back side of wire clip and place wires conveniently in appliance.
Heat shield
12) Reattach wires from step 5.
13) Plug the stepper motor into the ‘motor wire as shown below.
18) Match the remote control to the receiver - see remote control
instructions.
Motor wire
19) Reverse steps 2 and 1.
20) Check to ensure there are no gas leaks.
14) To unattach these wires - un-clip from the wires on the stepper
motor side as shown below.
Press down this tab
Regency HZ33CE Gas Fireplace
918-858a
35
2
09/16/09
HZ33CE / HZ54E / P33E / P33CE / P36E
INSTALLATION
GTMF
REMOTE INSTALLATION
INSTALLATION
GTMF REMOTE
1) Shut off the gas supply and disconnect all power to the unit.
If installing stepper motor (part 946-693 or 946-694), see Steps 7 - 8.
If not installing stepper motor, proceed to Step 10.
2) Remove the louvers or faceplate, if installed.
3) Disconnect battery pack - located on the floor of the unit, as shown
below and discard.
Do not use battery pack with remote receiver or an AC adaptor.
The fan control module, which is included with the kit serves
as an AC adaptor.
7) Remove the hi/lo knob by removing 2 screws as shown below.
Be sure to remove diaphragm and spring - discard both.
8) Install the stepper motor in the same location the hi/lo knob was
removed from - with 2 screws as shown below.
4) Identify wires in the GTMF remote wiring harness.
(see wiring diagram in unit manual.)
5) Locate green and white ON/OFF wires on both Remote and Unit
wiring harnesses.
Connect the TPTH and TH wires - green to green and white to
white as shown below
TPTH
9) Connect stepper motor wire to the lead marked motor on the remote
wiring harness.
10) Install 4 - AA batteries into the receiver.
Ensure correct polarity.
TH
6) Plug in receiver DC supply wire from the unit wiring harness, to the
DFC supply from the remote wiring harness - as shown below.
36
918-867b
Regency HZ33CE Gas Fireplace
1
03/11/14
HZ33CE / HZ54E / P33E / P33CE / P36E
11) Plug ‘receiver’ wires into the back of the receiver and bundle wires
with the wire clip - as shown below.
INSTALLATION
14) Install the heat shield onto the fan control module - then install
onto the velcro pad located on the floor of the unit located left
of the receiver.
Note: HZ54E unit only - fan control module and the receiver are in a
different location than shown above.
15) Plug fan control module into receptacle located on the left hand
side of the unit.
16) Match the remote control to the receiver - see remote control
instructions.
17) Reverse steps 2 and 1.
18) Check to ensure there are no gas leaks. on the newly installed
stepper motor.
12) Install the heat shield to the receiver with two screws and attach to
the floor of the unit with a velcro pad.
Heat shield
13) From the remote wire harness, plug the FCM wire into the fan
control module. Be careful not to damage.
FCM wire
Fan Control Module
Regency HZ33CE Gas Fireplace
37
INSTALLATION
WIRING DIAGRAMS
This heater does not require a 120V A.C. supply for operation. In case of a power failure, the burner switch and the optional remote control/thermostat will
continue to operate. However, a 120V A.C. power supply is needed for the fan/blower operation.
(Do not cut the ground terminal off under any circumstances.)
NOTE: Even if the fan is not purchased with the unit, it is still a good idea to bring power to the receptacle box (provided with the unit) in case
the fan is installed at a later date.
Proflame System
886 ON/OFF Stand Alone
Illustrated Wire Diagram
Spark Electrode
Sense Electrode
EI Pilot
Surefire Switch
(IPI / CPI)
886 Proflame Valve
Pilot Ground Wire
Chassis Ground
Standard Main ON/OFF
Switch or Optional Wall Switch
Proflame DFC Board
DFC Wire Harness Assembly
Note: 4 AA batteries must be installed to operate
the burner switch.
Do not use a 9 volt battery.
Optional AC Adaptor
Battery Holder
1 of 10
IMPORTANT: If the optional remote control is used, the AA batteries normally installed into the battery holder must be removed. The AA batteries in the
receiver now operate the unit. Having AA batteries in both the battery holder and receiver will damage the gas valve.
PROFLAME SYSTEM GT
885
Proflame System
Configuration
886 GTMF
Wire Diagram
SureFire™ Switch
Optional AC Adaptor
38
Regency HZ33CE Gas Fireplace
INSTALLATION
PROFLAME SYSTEM GTM
IMPORTANT: If the optional remote control is used, the AA batteries normally installed into the battery holder must be removed. The AA batteries in the
receiver now operate the unit. Having AA batteries in both the battery holder and receiver will damage the gas valve.
Proflame System
885Configuration
886 GTMF
Wire Diagram
SureFire™ Switch
Optional AC Adaptor
PROFLAME SYSTEM GTMF WITH OPTIONAL FAN
1 of 10
Proflame System
Configuration
885
886 GTMF
Wire Diagram
SureFire™ Switch
Lockwasher
Star washer
Neutral
120V AC
60 Hz
Live
Black
Ground
Black
Nut
Fan
ground wire
Regency HZ33CE Gas Fireplace
Fan
Ground
#8 Ground Lug
(for mobile home)
White
Black
Green
Black
Black
Fan Thermodisc
(normally open)
NOTE: Wiring schematics for HZ54E (120 Volts),
plug-in fan circuit with speed control switch on wall.
39
INSTALLATION
AC POWER ADAPTOR INSTALLATION (FOR SUREFIRE SYSTEMS)
40
Regency HZ33CE Gas Fireplace
INSTALLATION
INSTALLING THE OPTIONAL FAN (PRIOR TO UNIT INSTALLATION)
120 Volt AC power is needed for the fan switch and blower. The fan can be hard wired
if desired. The grounded duplex receptacle should be installed into the supplied
receptacle box by a qualified electrician. The neutral (wider) slot of the polarized
receptacle should be at the top.
Unit must be grounded at all times. Do not cut the ground terminal off under
any circumstances.
6. Attach the fan control box to the Control Plate. (Diagrams 5 & 6.
Fan Control Box
An optional fan can been installed prior to unit installation by following these steps.
1. Remove lower base cover by tilting forward and lifting out each side to release.
(Diagram 1).
Lower Base
Cover
Bottom Panel
Diagram 1
Control Mounting Plate
Diagram 5
Diagram 6
7. Position the control plate assembly on the left hand side of the
firebox. Diagram 7
8. Secure the control plate assembly with 1 screw as shown in Diagram
8.
2. Loosen four (4)screws (two on each side) inside of the bottom panel of the clean
front, slide panel out.
Diagram 2
3. Turn the fan base on its side (with the base facing towards you) and then slide
the fan in towards the rear of the unit. Turn the fan upright and slip it over the
two mounting studs. Take care not to damage the insulation on the fan base.
Ensure that the fan blades do not rub against the valve tubing.
Diagram 8
Diagram 7
9. Secure the fan wires and power cord by attaching one of the adhesive backed wire holder clips (Part #910-199. onto the Fireplace
base. Use the second clip to bundle up the wires approximately 4"
from the control box. Ensure that there is no interference with the
wires when the faceplate and trim are installed and that no wires
will touch the hot metal surfaces or sharp edges.
10.Plug the fan power cord into the rear end of the receptacle box to
provide the maximum clearance.
11.Reverse Steps 1 and 2.
TO REMOVE THE FAN
Diagram 3
4. Connect fan ground cable to ground lug. Refer to wiring diagram.
5. Slide the thermodisc/cover assembly into the bracket clip on the underside of
the firebox (Diagram 4 ).
Check that no wires will touch hot surfaces. 1. Shut the power off.
2. Follow Steps 2 - 7 of `Installing the optional fan after unit is installed`.
3. Reverse Step 8 of `Installing the optional fan after unit is installed`.
Note: The bearings are lubricated for life. Do not lubricate them.
Make sure you vacuum the fan area on a regular basis.
IMPORTANT:
These fans collect a lot of dust from within your home. Ensure you
maintain these fan motors on a regular basis by vacuuming out
the fan blades and housing using a soft brush nozzle.
Diagram 4
Regency HZ33CE Gas Fireplace
41
INSTALLATION
OPTIONAL FAN WIRING DIAGRAM
Lockwasher
Star washer
Fan
Ground
#8 Ground Lug
(for mobile home)
Neutral
120V AC
60 Hz
Live
Ground
ON
Green
OFF
Black
Nut
Fan
ground wire
Rotary Speed
Control
Red
Red
Fan Thermodisc
(normally open)
NOTE: Wiring schematics for P36E-4 (120 Volts),
plug-in fan circuit with speed control switch on wall.
INSTALLING THE OPTIONAL FAN (INSTALLED UNIT)
120 Volt AC power is needed for the fan switch and blower. The fan can be
hard wired if desired. The grounded duplex receptacle should be installed into the supplied receptacle box by a qualified electrician. The neutral (wider)
slot of the polarized receptacle should be at the top.
6. Remove 2 screws in location shown below - slide burner to the right
then lift out. (See Diagram 2.
Unit must be grounded at all times. Do not cut the ground terminal off
under any circumstances.
1. Shut the power off.
2. Remove Flush door (See instructions in this Manual).
3. Remove inner panels (See instructions in this Manual).
4. Remove glass crystals or ceramic stones.
5. Remove the base tray by removing 6 screws in the locations shown
below.
Diagram 2
Diagram 1: Remove the 6 screws and then lift
out the base tray
42
Regency HZ33CE Gas Fireplace
INSTALLATION
7. Remove the 12 screws securing the valve tray assembly in place
(Diagram 3. and then lift the entire assembly out.
12.Remove lower base cover by lifting out (Diagram 7.
Diagram 7
13.Attach the fan control box to the Control Plate. (Diagrams 8 & 9).
Fan Control Box
Diagram 3
8. Manoeuvre fan into valve tray opening at base of firebox.
Control Mounting Plate
Diagram 8
Diagram 9
14.Position the control plate assembly on the left hand side of the firebox.
Diagram 10
15.Secure the control plate assembly with 1 screw as shown in Diagram
11.
Diagram 4
9. Secure fan by pushing fan down onto mounting pins located on floor of
unit. Take care not to damage the insulation on the fan base. Ensure
that the fan blades do not rub against the valve tubing. Diagram
5.
Diagram 10
Diagram 11
16.Secure the fan wires and power cord by attaching one of the adhesive
backed wire holder clips (Part #910-199. onto the Fireplace base.
Use the second clip to bundle up the wires approximately 4" from the
control box. Ensure that there is no interference with the wires when
the faceplate and trim are installed and that no wires will touch the hot
metal surfaces or sharp edges.
17.Plug the fan power cord into the rear end of the receptacle box to
provide the maximum clearance.
Diagram 5
10.Connect fan ground cable to ground lug. Refer to wiring diagram.
11. Slide the thermodisc/cover assembly into the bracket clip on the
underside of the firebox (Diagram 6 ).
Check that no wires will touch the hot surfaces. 18. Reverse Step 1-7.
TO REMOVE THE FAN
1. Shut the power off.
2. Reverse the above instructions.
Note: The bearings are lubricated for life. Do not lubricate them.
Make sure you vacuum the fan area on a regular basis.
Diagram 6
Regency HZ33CE Gas Fireplace
IMPORTANT:
These fans collect a lot of dust from within your home. Ensure you
maintain these fan motors on a regular basis by vacuuming out the
fan blades and housing using a soft brush nozzle.
43
INSTALLATION
Optional
WALL THERMOSTAT
Optional
REMOTE CONTROL
Use the Regency Remote Control Kit approved
for this unit. Use of other systems may void
your warranty.
®
A wall thermostat may be installed if desired,
connect the wires as per the wiring diagram.
Use table below to determine the maximum
wire length.
Note: Preferable if the thermostat is
installed on an interior wall.
Regency® offers an optional programmable
thermostat but any 250-750 millivolt rated nonanticipator type thermostat that is CSA, ULC or
UL approved may be used.
CAUTION
Do not wire millivolt
wall thermostat wires
to 120V wire.
Thermostat Wire Table
Recommended Maximum Lead Length
(Two-Wire) When Using Wall
Thermostat (CP-2 System)
Wire Size
Max. Length
14 GA.
50 Ft.
16 GA.
32 Ft.
18 GA.
20 Ft.
20 GA.
12 Ft.
22 GA.
9 Ft.
The remote control kit comes with a hand held
transmitter, a receiver and a wall mounting plate.
1. Choose a convenient location on the wall
to install the receiver and the receptacle
box (protection from extreme heat is very
important). Run wires from the fireplace to
that location. Use Thermostat Wire Table.
2. Connect the two wires to the gas valve. See
wiring diagram. Wall switch GT/GTM using
wire 0.584.907
CAUTION
Do not wire millivolt
remote control wires
to 120V wire.
3. Install 3 AAA alkaline batteries in transmitter
and 4 AA alkaline batteries in the receiver.
Install the receiver and its cover in the wall.
Switch the remote receiver to "remote"
mode. The remote control is now ready for
operation.
WALL SWITCH
1. Run the supplied wire through the right or
left side gas inlet opening. Be careful not
to damage wire.
Note: We recommend a maximum of 15'
of wire but if you wish to go with a
longer run, use the Thermostat Wire
Table.
2. Connect the wire to the wall switch and
install into the receptacle box. Also attach
wires to the valve as shown below.
CAUTION
Do not wire millivolt
wall switch wire
to 120V wire.
AERATION
ADJUSTMENT
The burner aeration is factory set but may need
adjusting due to either the local gas supply or
altitude. Open the air shutter for a blue flame by
pulling down on the rod or close for a more yellow
flame by pushing up on the rod.
Minimum Air Shutter Opening:
NG
NG with Logs NG with Stones 1/16"
3/16”
3/16”
LP
`
LP with Logs LP with Stones 3/16"
Full open
Full open
CAUTION: Carbon will be produced if air shutter
is tightly closed.
BATTERY INSTALLATION
Note: Any damage due to carboning
resulting from improperly setting
the aeration controls is NOT covered
under warranty.
1. 4 AA batteries must be installed in the battery pack to operate the burner switch.
2. Install 2 AA batteries per side and connect as shown below - the battery pack is located on the lower left side of the unit.
44
Regency HZ33CE Gas Fireplace
INSTALLATION
OPTIONAL REFLECTIVE PANEL INSTALLATION
Before installation, panels must be handled and cleaned as per instructions noted below:
Black Enamel Panels
• Black Enamel panels must be inspected for scratches and dimples prior to installation.
for damage after installation will not receive consideration.
All claims to be recorded at this time. Claims
• Black Enamel panels will discolor a little during normal operation.
This is normal and should not be considered a defect.
All hand and finger marks MUST be cleaned off with a soft cloth.
*fingerprints
before applying heat to the unit.
Use an ammonia based cleaner (ie. glass cleaner) to remove any
Failure to do this will result in burn stain on panels which you will be unable to remove. Not protected by product warranty.
1. Remove flush glass door and firebox base tray by removing 6 screws
in the locations shown below.
5. S
ecure back panel with panel bracket as shown below. This bracket
will come with the appliance and is enclosed in manual package.
Diagram 1: Remove the 6 screws - lift out base tray
Diagram 4
2. Remove 4 screws prior to top panel installation.
Do not remove this panel.
6. The side panels are installed last, slide in as shown in Diagram 5.
Note: The bend in the metal on the side panels should face inward
(toward the wall of the firebox - see Diagram 5). If the side panels
have been installed incorrectly the firebox base will not fit.
Diagram 1
3. Place the top panel in first, secure with 4 screws.
(See Diagram 2 for screw locations)
Diagram 2
Diagram 5
Diagram 6
7. Reinstall the firebox base and glass door.
Diagram 3
4. With the top panel in place - install back panel. The back panel fits
under the top panel, push the top panel up to fit back panel into
position. (Diagram 3)
Completed Panel Installation
Back Panel
Regency HZ33CE Gas Fireplace
Diagram 3
Note: Diagram is shown without a burner.
45
INSTALLATION
GLASS CRYSTALS AND OPTIONAL STONES
INSTALLATION ON BURNER AND FIREBOX FLOOR
Evenly spread the Glass Crystals or optional Ceramic Spa Stones over the burner.
Ensure the crystals (or stones) do not overlap too much as this will effect the flame pattern.
IMPORTANT NOTE:
Only the supplied approved Glass Crystals and Stones are to be used with these fireplaces. Use of any other type of glass crystals or stones can
alter the unit's performance, any damage caused by the use of any unapproved glass or stones will not be covered under warranty.
When using Ceramic Spa Stones DO NOT cover burner ports or pilot light that lead to pilot flame. Ensure the crystals or stones do not overlap
excessively as this will effect the flame pattern.
BURNER PACKAGES
Unit
*Glass Crystals
**Spa Stones
HZ33CE
4 lb
4 lb glass + 70 spa stones
Volcanic Stones
4 lb glass + 30 stones
NOTE: * Glass Crystals are available in 1lb and 5lb bags.
** Spa stone package contains 70 stones
3) Work Crystals from back to front
edge of Firebox Floor
Glass Crystals shown on Burner and Firebox Floor
1) Start installing Crystals on back of
Burner and Firebox Floor
2) Distribute Crystals evenly towards
front of Burner and Firebox Floor
4) Spread Crystals evenly over the
burner and firebox base
5) Ensure Crystals DO NOT block the
front of the pilot hood and flame to
light the burner
NOTE: Correct final glass installation of Crystals shown
in step 4 and 5.
The Burner and Firebox Floor should not be visible
when the flame is out.
OPTIONAL SPA STONES INSTALLATION (AROUND BURNER)
NOTE: Spa stones are NOT to be placed anywhere on the burner tube or Pilot assembly area.
46
Regency HZ33CE Gas Fireplace
HZ33CE/HZ30E
INSTALLATION
OPTIONAL LOG
SETINSTALLATION
INSTALLATION
HZ33CE/HZ30E
- LOG
Read the instructions below carefully and refer to the images. If the logs are broken do not use the unit until they are replaced. Broken
logs can interfere with pilot operation.
Improper positioning of the logs and lava embers may create carbon build-up and can alter the unit's performance which is not covered
under warranty.
*Satin black paint is included if touch ups are required.
6. Install log clip to lip on burner tray - position 9-1/2" from the left edge
of the burner tray to the centre of clip.
1
Rear Log
2
Right Log
3
Left Log
4
Front Right Log Piece
5
Front Left Log Piece - HZ33CE Only
Lava Embers/Rocks
9-1/2"
Log Clip - HZ33CE only
Log Brackets - HZ33CE / HZ30E
1
HZ33CE Log Bracket
HZ33CE Log Clip
7. Install Rear Log (1), seat on log clip and rest on left log bracket.
Right side of log should sit flush with the outside edge of the pilot hood.
2
1
3
5
4
Log 1 in position
1. Shut off gas and electrical supply, allow unit to cool to room temperature.
Log 1 end of Log flush
with edge of pilot hood
8. Place Log 5 on the glass crystals on the left side.
2. Remove flush glass door (see unit manual).
3. Carefully remove the logs from the packaging and unwrap them.
The logs are fragile, handle with care -never force into position.
1
4. Ensure glass crystals are installed on the burner.
HZ33CE = 4lbs HZ30E=1lb
5
HZ33CE INSTALL INSTRUCTIONS:
5. HZ33CE only- Install log bracket onto left side of burner with 2 screws
as shown below.
HZ33CE shown - Logs 1 and 5 in position.
9. Place Log 4 on the glass on the right side in location shown below.
5
HZ33CE - install
bracket, left side
919-265
Regency HZ33CE Gas Fireplace
4
HZ33CE shown - Logs 1,4 and 5 in position.
1
07/10/13
47
HZ33CE/HZ30E
INSTALLATION
9. Place Left Log (2 ) match pin landing on Log 2 with pin on Log 1, the
bottom should rest on the glass as shown below.
1. Install the log clips on the burner tray - measure 2-1/2" from theoutside
edge of the pilot hood to the outside edge of the log clip.
HZ33CE use bottom
pin landing
2
HZ30E INSTALL INSTRUCTIONS:
1
HZ33CE shown - Left Log (2) positioned to rest on Log 1 and
glass crystals.
10. Adjust position of Log 4 – log should sit as shown below, 14" from
the left outside of the burner tray.
Log clips installed
HZ30E
1
2
4
14"
11. Position Log 3, line up bottom pin landing on Log 3 with pin on
Log 1. The remainder of Log 3 will rest on the burner tray.
2. Position Back Log (1) by positioning centre of Log on centre of pilot
hood.Rest Log 1 on log clips.
Each end should rest on the lip of the burner tray – as shown below.
1
5
2
HZ33CE use
bottom pin
landing
4
3
12. Place lava embers/rocks on glass - ensure rocks do not block pilot.
Do not place lava rocks/embers too close to logs as this may cause
carboning.
13. Adjust aeration, see unit manual for setting.
HZ30E shown - Log 1 in position
3. Position Log 2, line up pin landing on Log 2 with pin on Log 1, remainder
of Log 2 rests on the burner tray as shown below.
HZ30E use top
pin landing
HZ33CE shown - Final Install
48 919-265
HZ30E shown - installing Log 2
2
07/10/13
Regency HZ33CE Gas
Fireplace
HZ33CE/HZ30E
INSTALLATION
4. Position Log 3, line up bottom pin landing on Log 3 with pin on Log 1.
The remainder of Log 3 will rest on the burner tray.
1
HZ30E use top
pin landing
2
3
HZ30E shown - Log 3 install
5. Place Left Log (4) piece on burner tray, part of the Log should sit on
the lip of the burner tray as shown below.
1
2
4
3
HZ30E shown - Log 3 install
6. Place lava embers/rocks on glass - ensure rocks do not block pilot.
Do not place lava rocks/embers too close to logs as this may cause
carboning.
7. Adjust aeration, see unit manual for setting.
HZ30E shown - Final Install
Regency HZ33CE Gas Fireplace
919-265
49
3
07/10/13
INSTALLATION
GLASS SCREEN GUARD AND GLASS DOOR INSTALLATION
STANDARD FLUSH DOOR AND SCREEN
Both the standard flush door and glass screen guard come with a
black frame. To install the glass screen guard simply hook the over top of
the flush glass door see Diagram 1. Install both screen and glass door
by hooking the top door flange onto the top of the unit and swing the door
towards the unit, Diagram 2. Be careful that the glass gasket does not roll
up; there must be a gap between the gasket and the door lip to ensure
that the door sits securely on the unit. See Diagram 3.
Glass Door
Screen Door
Diagram 2
Diagram 1
Diagram 3
Use the hook to pull the spring out until you can put the hook
into the slot on the bottom door bracket. Repeat for 2nd spring.
See Diagram 4.
Diagram 4
To remove the flush door and screen, reverse the above steps.
50
Regency HZ33CE Gas Fireplace
INSTALLATION
OPTIONAL 4-SIDED FACEPLATE INSTALLATION
If installing the optional faceplate ensure the combustible
and non combustible material around the unit are installed
flush with the unit. (See Diagram 1 below).
The faceplate cannot be installed if materials are not flush.
3. Line up the middle rib on backside of faceplate with middle indent on bracket.
This will centre the faceplate and allow 1/16" adjustment from side to side.
Combustible
Material
Non-combustible Material (3-1/2" x 36")
Nailing Strip -1/2" back from unit face
Middle Rib on Faceplate
Diagram 4 -Line up faceplate and bracket.
4. Lift faceplate up and lower gently onto bracket.
Combustible
Material
Diagram 1- Materials flush w/unit.
1. Install 2 middle screws on unit face - do not tighten. Slide
bracket over screws then tighten. Install 2 outer screws .
Install middle 2 screws on
to unit first
Diagram 2 -Bracket screw locations on unit.
Diagram 5 -Hang faceplate on bracket
2. Install four (4) wood screws, two (2) on each side of the
bracket into the wall studs as shown below.
Diagram 6 -Final Install
Diagram 3 -Bracket screw locations.
Regency HZ33CE Gas Fireplace
51
INSTALLATION
OPTIONAL MANTEL INSTALLATION
If installing the optional mantel ensure the combustible and
non combustible material around the unit are installed flush
with the unit. (See Diagram 1 below).
The mantel cannot be installed if materials are not flush.
3. Repeat steps 1 and 2 to install lower bracket - screw locations are shown
below.
Combustible
Material
Non-combustible Material (3-1/2" x 36")
Nailing Strip -1/2" back from unit face
4. Line up flange on hearth portion of mantel, with opening between bracket
and unit.
Combustible
Material
Diagram 1- Materials flush w/unit.
1. Install 2 middle screws on unit face - do not tighten. Slide
bracket over screws then tighten, install 2 outer screws .
5. Lift up mantel and line up the middle rib on backside of faceplate with
middle indent on bracket. This will centre the faceplate and allow 1/16"
adjustment from side to side.
Install middle 2 screws on
to unit first
Diagram 2 -Bracket screw locations on unit.
2. Install four (4) wood screws, two (2) on each side of the
bracket into the wall studs as shown below.
Diagram 3 -Bracket screw locations into stud.
Diagram 6 -Final Install
52
Regency HZ33CE Gas Fireplace
OPERATING INSTRUCTIONS
INSTALLATION
OPERATING
INSTRUCTIONS
1. Read and understand these instructions
before operating this appliance.
2. Check to see that all wiring is correct and
enclosed to prevent possible shock.
3. Check to ensure there are no gas leaks.
4. Make sure the glass in the glass door frame
is properly positioned. Never operate the
appliance with the glass removed.
5. Verify that the venting and cap are
unobstructed.
6. The unit should never be turned off, and on
again without a minimum of a 60 second
wait.
LIGHTING PROCEDURE
1. Turn on ON/OFF switch or press and release
on ON/OFF button once on the remote
control if being used.
3. The unit will turn on.
It is possible that you will hear some sounds from
your gas appliance.This is perfectly normal due to
the fact that there are various gauges and types
of steel used within your appliance. Listed below
are some examples. All are normal operating
sounds and should not be considered as defects
in your appliance.
Note: The first try for ignition will last approximately 60 seconds. If there is no flame ignition (rectification) the board will stop sparking
for approximately 35 seconds. After wait time
, the board will start second try for ignition
by sparking for approximately 60 seconds . If there is still no positive ignition the board
will go into lock out.
Burner Tray:
The burner tray is positioned directly under the
burner and is made of a different gauge material
from the rest of the firebox and body. Therefore,
the varying thicknesses of steel will expand and
contract at slightly different rates which can cause
"ticking" and "cracking" sounds. You should also
be aware that as there are temperature changes
within the unit these sounds will likely re-occur.
Again, this is normal for steel fireboxes.
2. After approximately 4 seconds the spark
ignition system will spark for 60 seconds to
light the main burner.
The system will need to be reset as follows:
FIRST FIRE
The FIRST FIRE in your heater is part of the
paint curing process. To ensure the paint is properly cured, it is recommended you burn your
fireplace for at least four (4. hours the first time.
When first operated, the unit will release an
odour caused by the curing of the paint and the
burning off of any oils remaining from manufacturing. Smoke detectors in the house may go off
at this time. Open a few windows to ventilate
the room for a couple of hours. The glass may
require cleaning.
NOTE:When the glass is cold and the appliance
is lit, it may cause condensation and fog
the glass. This condensation is normal
and will disappear in a few minutes as
the glass heats up.
DO NOT ATTEMPT TO CLEAN THE
GLASS WHILE IT IS STILL HOT!
NORMAL OPERATING
SOUNDS OF
GAS APPLIANCES
a) Turn the system off using ON/OFF switch
or press ON/OFF button - if using optional
remote.
b) After approximately 2 seconds turn on ON/
OFF switch or press ON/OFF button if using optional remote.
c) Repeat step 1.
SHUTDOWN
PROCEDURE
Pilot Flame:
While the pilot flame is on it can make a very
slight "whisper" sound.
Gas Control Valve:
As the gas control valve turns ON and OFF, a
dull clicking sound may be audible, this is normal
operation of a gas regulator or valve.
Unit Body/Firebox:
Different types and thicknesses of steel will
expand and contract at different rates resulting
in some "cracking" and "ticking" sounds will be
heard throughout the cycling process.
1. Turn ON/OFF switch or press and release
the ON/OFF button once if using optional
Remote Control.
2. If service is to be performed - you must
disconnect both sources of power to the
unit, the main power and battery.
DO NOT BURN THE UNIT WITHOUT THE
GLASS DOOR IN PLACE.
During the first few fires, a white film
may develop on the glass front as part of
the curing process. The glass should be
cleaned after the unit has cooled down
or the film will bake on and become very
difficult to remove. Use a non-abrasive
cleaner and DO NOT ATTEMPT TO CLEAN
THE GLASS WHILE IT IS HOT.
Regency HZ33CE Gas Fireplace
53
OPERATING INSTRUCTIONS
COPY OF LIGHTING PLATE INSTRUCTIONS
FOR YOUR SAFETY READ BEFORE LIGHTING
This appliance must be installed in accordance with local codes, if any;
if none, follow the National Fuel Gas Code, ANSI Z223.1/NFPA 54, or
Natural Gas and Propane Installation Codes, CSA B149.1.
WARNING: If you do not follow these instructions exactly, a fire or explosion may result
causing property damage, personal injury or loss of life. Improper installation, adjustment,
alteration, service or maintenance can cause injury or property damage. Refer to the owner’s
information manual provided with this appliance. For assistance or additional information
consult a qualified installer, service agency or gas supplier.
AVERTISSEMENT. Quiconque ne respecte pas à la lettre les instructions dans la présente notice
risquede déclencher un incendie ou une explosion entraînant des dommages, des blessures ou
la mort.
Une installation, d'ajustement, de modification, de service ou d'entretien peut provoquer
des blessures ou des dommages matériels. Reportez-vous au manuel du propriétaire de
l'information fournie avec cet appareil. Pour obtenir de l'aide ou des informations supplémentaires consulter un installateur qualifié, une agence de service ou fournisseur de gaz.
A) This appliance is equipped with an ignition device which automatically lights the pilot.
Do not try to light the pilot by hand.
B) BEFORE OPERATING smell all around the appliance area for gas. Be sure to smell next to the floor
because some gas is heavier than air and will settle on the floor.
WHAT TO DO IF YOU SMELL GAS
- Do not try to light any appliance.
- Do not touch any electric switch, do not use any phone in your building.
- Immediately call your gas supplier from a neighbours phone. Follow the gas supplier’s instructions.
- If you cannot reach your gas supplier, call the fire department.
C) Do not use this appliance if any part has been under water. Immediately call a qualified service
technician to inspect the appliance and replace any part of the control system and any
gas control which has been underwater.
A) Cet appareil est muni d’un dispositif d’allumage qui allume automatiquement la veilleuse.
Ne tentez pas d’allumer la veilleuse manuellement.
Part #: 918-628
Rev: B
Colours: Black on Grey, except
for parts indicated as being
Red.
Size:
July 17/09:
Feb. 18/10:
100%
w- 5.16"
h- 9.97"
Added french
Revised instructions
B) AVANT DE FAIRE FONCTIONNER, reniflez tout autour de l’appareil pour déceler une odeur
de gaz. Reniflez près du plancher, car certains gaz sont pluslourds que l’air et peuvent
s’accumuler au niveau du sol.
QUE FAIRE SI VOUS SENTEZ UNE ODEUR DE GAZ :
• Ne pas tenter d’allumer d’appareil
• Ne touchez à aucun interrupteur; ne pas vous servir des téléphones se trouvant dans le
bâtiment.
• Appelez immédiatement votre fournisseur de gaz depuis un voisin. Suivez les
instructions du fournisseur.
• Si vous ne pouvez rejoindre le fournisseur, appelez le service des incendies
C) N’utilisez pas cet appareil s’il a été plongé dansl’eau, même partiellement. Faites inspecter l’appareil par un technicien qualifié et remplacez toute partie du système de contrôle et toute commande qui ont été plongés dans l’eau.
CAUTION: Hot while in operation. Do not touch. Severe Burns may result. Due to high surface
temperatures keep children, clothing and furniture, gasoline and other liquids having flammable
vapors away. Keep burner and control compartment clean. See installation and operating
instructions accompanying appliance.
LIGHTING INSTRUCTIONS
1) Turn on ON/OFF switch
2) After approximately 4 seconds the spark ignition system will spark for 60 seconds to light the main
burner.
3) The unit will turn on.
Note: The first attempt to ignition will last approximately 60 seconds. If there is no flame ignition (rectification) the board will stop sparking for approximately 35 seconds. After this wait time, the board will start a
second try for ignition by sparking for approximately 60 seconds. If there is still no positive ignition after the
second attempt the board will go into lock out.
The system will need to be reset as follows (after going into lock out mode):
a) Wait 5 minutes - turn the system off using ON/OFF switch.
b) After approximately 2 seconds turn on ON/OFF switch or press ON/OFF button if using optional
remote.
c) Unit will repeat step 2.
1) Appuyez le bouton ON / OFF
2) Attendre 4 secondes. Le système d’allumage produira des étincelles pendant 60 secondes afin d’amorcer
le brûleur principal.
3) Les flammes s’allumeront.
Remarque : Au premier allumage, le système tente d’allumer les flammes pendant 60 secondes. Si l’essai est
infructueux, le système fait une pause de 35 secondes. C’est ce qu'on appelle l'étape de rectification. Ce délai
écoulé, le système tente à nouveau d'allumer les flammes en produisant des étincelles pendant 60 secondes.
Si les flammes ne s’allument toujours pas, le système se met en mode verrouillage.
Il faut alors le réinitialiser en suivant les étapes ci-dessous (pour le déverrouiller) :
a) Attendre 5 minutes et éteindre l’appareil en réglant l’interrupteur à la position « OFF »;
b) Attendre 2 secondes et rallumer le système à l’aide de l’interrupteur ou de la télécommande.
c) L'unité répétera l'étape 2.
TO TURN OFF GAS APPLIANCE
1)
2)
Turn off ON/OFF switch
If service is to be performed - you must disconnect power to the unit, from the battery pack, refer to
manual.
1)
2)
Appuyez sur le bouton ON / OFF
Si le service est effectuée, vous devez débrancher l'appareil, du bloc-piles, voir le manuel d'instruction
pour plus de détails.
DO NOT REMOVE THIS INSTRUCTION PLATE
54
918-628b
Regency HZ33CE Gas Fireplace
MAINTENANCE
MAINTENANCE
INSTRUCTIONS
GENERAL VENT
MAINTENANCE
1. Always turn off the gas valve before cleaning.
For relighting, refer to lighting instructions.
Keep the burner and control compartment
clean by brushing and vacuuming at least
once a year.
Conduct an inspection of the venting system
semi-annually. Recommended areas to inspect
as follows:
2. Clean appliance and door with a damp
cloth (never when unit is hot). Never use
an abrasive cleaner. The glass should be
cleaned with a gas fireplace glass cleaner.
The glass should be cleaned when it
starts looking cloudy.
3. The faceplate is finished in a heat resistant
paint and should only be refinished with heat
resistant paint. Regency® uses StoveBright
Paint - Metallic Black #6309.
4. Make a periodic check of burner for proper
position and condition. Visually check the
flame of the burner periodically, making sure
the flames are steady; not lifting or floating.
If there is a problem, call a qualified service
person.
5. The appliance and venting system must be
inspected before use, and at least annually,
by a qualified field service person, to ensure
that the flow of combustion and ventilation
air is not obstructed.
Note: Never operate the appliance without
the glass properly secured in place.
6. Do not use this appliance if any part has been
under water. Immediately call a qualified
service technician to inspect the appliance
and to replace any part of the control system
and any gas control which has been under
water.
7. In the event this appliance has been
serviced check that the vent-air system
has been properly resealed & reinstalled
in accordance with the manufacturer's
instructions.
8. Verify operation after servicing.
Regency HZ33CE Gas Fireplace
1. Check the Venting System for corrosion in
areas that are exposed to the elements.
These will appear as rust spots or
streaks, and in extreme cases, holes.
These components should be replaced
immediately.
2. Remove the Cap, and shine a flashlight
down the Vent. Remove any bird nests, or
other foreign material.
3. Check for evidences of excessive
condensation, such as water droplets forming
in the inner liner, and subsequently dripping
out the joints, Continuous condensation can
cause corrosion of caps, pipe, and fittings. It
may be caused by having excessive lateral
runs, too many elbows, and exterior portions
of the system being exposed to cold weather.
4. Inspect joints, to verify that no pipe
sections or fittings have been disturbed,
and consequently loosened. Also check
mechanical supports such as Wall Straps,
or plumbers' tape for rigidity.
GLASS GASKET
If the glass gasket requires replacement use a
tadpole glass gasket (Part # 936-155..
GLASS DOOR
Your Regency® fireplace is supplied with high
temperature 5mm-Ceramic glass. If your glass
requires cleaning, we recommend using an
approved glass cleaner available at all authorized
dealers. Do not use abrasive materials.
CAUTION & WARNINGS:
* Do not clean when the glass is hot.
* The use of substitute glass will void all product
warranties.
* Care must be taken to avoid breakage of the
glass.
* Do not strike or abuse the glass.
* Do not operate this fireplace without the glass
front or with a cracked or broken glass front.
* Wear gloves when removing damaged or
broken glass.
* Replacement of the glass panel(s) should be
done by a licensed or qualified service per
son.
GLASS REPLACEMENT
In the event that you break your glass by impact,
purchase your replacement from an authorized
Regency® dealer only.
Replacement glass is shipped already installed
into the door frame.
CAUTION: Wear gloves when
removing damaged or broken
glass.
WARNING: Do not operate the
appliance with the glass panels
removed, cracked or broken.
Replacement of the glass panels
should be done by a licensed or
qualified service person.
55
MAINTENANCE
VALVE TRAY REPLACEMENT
Removing Valve
8. Remove the 12 screws securing the valve tray assembly in place
(Diagram 4. and then lift the entire assembly out (Diagram 5..
1. Shut off the gas supply.
NOTE: Parts have been hidden to shown screw locations.
2. Remove the faceplate.
3. Open the flush door and remove the door.
4. Remove 6 screws in locations shown below to remove base tray and
pilot hood (See Diagram 1..
Diagram 4
Diagram 1: Remove the 6 screws and then lift
out the base tray
5. Remove 2 screws in location shown below - slide burner to the right
then lift out. (See Diagram 2.
Diagram 5: Lift out Valve Tray Assembly
Installing Valve
Diagram 2
1. Install new Valve Tray Assembly.
6. Disconnect the inlet gas line.
7. Disconnect the EV1, EV2, and ground wires from the valve - as shown
below.
Ground
Diagram 3
56
EV1
2. Reverse steps 8-1.
EV2
Regency HZ33CE Gas Fireplace
PARTS LIST
MAIN ASSEMBLY
Part #
Description
10
432-917
Fan Assembly
Orifice #47 NG
11
437-018
Access panel
904-241
Orifice #56 LP
12
437-024
Screen Frame
911-004
886 Proflame Valve
13
433-538
Door Assembly
437-023
**Clean Front Face
433-511
**Firebox Assembly
Not a replacement part
Part #
Description
1
770-523
Thermodisc Cage Assy
2
904-434
3
4
437-578
Valve Assembly
14
5
437-012
Bracket
15
6
437-525
Burner Assembly
**
7
437-015
Burner Filler Tray Assy
911-006
Pilot Assembly - NG
Pilot Cover
911-007
Pilot Assembly - LP
919-120
Manual
8
437-004
14
13
12
11
8
7
6
5
15
4
10
2
1
Regency HZ33CE Gas Fireplace
3
57
PARTS LIST
ACCESSORIES
Part #
Description
1
434-044
Enamel Panel Top
2
434-042
Enamel Panel Left
3
434-041
Enamel Panel Right
4
434-043
Enamel Panel Back
3
1
4
2
58
Regency HZ33CE Gas Fireplace
WARRANTY
Regency® Fireplace Products are designed with reliability and simplicity in mind. In addition, our internal Quality Assurance Team carefully inspects each unit
thoroughly before it leaves our facility. FPI Fireplace Products International Ltd. is pleased to extend this limited lifetime warranty to the original purchaser of a
Regency® Product. This warranty is not transferable.
The Warranty: Limited Lifetime
The combustion chamber, heat exchanger, burner tubes/pans, logs, glass crystals, ceramic spa stones, pebbles, brick panels and gold plating (against defective manufacture
only) are covered under the Limited Lifetime Warranty for five (5. years for parts and subsidized labour* and parts only thereafter.
Glass is covered for lifetime against thermal breakage only, parts and subsidized labour* for five (5. years and parts only thereafter from date of purchase.
External casting, surrounds and grills are covered against cracks and warps resulting from manufacturer defects, parts and subsidized labour* for three (3. years from the date
of purchase and parts only thereafter.
Special Finishes - One year on stainless steel panels, nickel overlays,nickel faceplates, brushed nickel and antique copper full screens and doors. You can expect some changes
in color as the product "ages" with constant heating and cooling. FPI warranties the product for any manufacturing defects on the original product. However, the manufacturers
warranty does not cover changing colors and marks, ie. finger prints, etc applied after the purchase of the product. Damage from the use of abrasive cleaners is not covered
by warranty.
Electrical and mechanical components such as blowers, switches, wiring, thermodiscs, FPI remote controls, spill switches, thermopiles, thermocouples, pilot assembly components,
and gas valves are covered for two years parts and one year subsidized labour* from the date of purchase. Blowers and valves replaced under warranty are considered repairs
and continue as if new with appliance. ie. twelve (12. months from original purchase date of appliance with a minimum of three (3. months coverage from date of replacement.
FPI venting components are covered parts and subsidized labour* for three (3. years from date of purchase.
Simpson Dura-Vent venting components (Direct Vent units) are covered by Simpson Dura-Vent Inc. warranty.
Repair/replacement parts purchased by the consumer from FPI after the original coverage has expired on the unit will carry a 90 day warranty, valid with a receipt only. Any item
shown to be defective will be repaired or replaced at our discretion. No labor coverage is included with these parts.
Conditions:
Any part or parts of this unit which in our judgement show evidence of such defects will be repaired or replaced at FPI's option, through an accredited distributor or agent provided
that the defective part be returned to the distributor or agent Transportation Prepaid, if requested.
Porcelain/Enamel - Absolute perfection is either guaranteed nor commercially possible. Any chips must be reported and inspected by an authorized dealer within three days of
installation. Reported damage after this time will be subject to rejection.
It is the general practice of FPI to charge for larger, higher priced replacement parts and issue credit once the replaced component has been returned to FPI and evaluated for
manufacturer defect.
The authorized selling dealer is responsible for all in-field service work carried out on your Regency® product. FPI will not be liable for results or costs of workmanship from
unauthorized service persons or dealers.
At all times FPI reserves the right to inspect product in the field which is claimed to be defective.
All claims must be submitted to FPI by authorized selling dealers. It is essential that all submitted claims provide all of the necessary information including customer name,
purchase date, serial #, type of unit, problem, and part or parts requested, without this information the warranty will be invalid.
Exclusions:
This limited Lifetime Warranty does not extend to or include paint, door or glass gasketing or trim.
At no time will FPI be liable for any consequential damages which exceed the purchase price of the unit. FPI has no obligation to enhance or modify any unit once manufactured.
ie. as products evolve, field modifications or upgrades will not be performed.
FPI will not be liable for travel costs for service work.
Installation and environmental problems are not the responsibility of the manufacturer and therefore are not covered under the terms of this warranty policy.
Embers, rockwool, gaskets, door handles and paint are not covered under the terms of this warranty policy.
Any unit which shows signs of neglect or misuse is not covered under the terms of this warranty policy.
The warranty will not extend to any part which has been tampered with or altered in any way, or in our judgment has been subject to misuse, improper installation, negligence
or accident, spillage or downdrafts caused by environmental or geographical conditions, inadequate ventilation, excessive offsets, negative air pressure caused by mechanical
systems such as furnaces, fans, clothes dryer, etc.
Freight damage to stoves and replacement parts is not covered by warranty and is subject to a claim against the freight carrier by the dealer.
FPI will not be liable for acts of God, or acts of terrorism, which cause malfunction of the appliance.
Performance problems due to operator error will not be covered by this warranty policy.
Products made or provided by other manufacturers and used in conjunction with the operation of this appliance without prior authorization from FPI, may nullify your warranty
on this product.
Any alteration to the unit which causes sooting or carboning that results in damage to the interior / exterior faceplate is not the responsibility of FPI.
* Subsidy according to job scale as predetermined by FPI.
Regency HZ33CE Gas Fireplace
59
Register your Regency® warranty online
www.regency-fire.com
Reasons to register your product online today!
• View and modify a list of all your registered products.
• Request automatic email notification of new product updates.
• Stay informed about the current promotions, events, and special offers on related products.
Installer: Please complete the following information
Dealer Name & Address:_______________________________________________
___________________________________________________________________
HZ33CE Video
Installer:____________________________________________________________
Phone #:____________________________________________________________
Date Installed:_ ______________________________________________________
Serial No.:___________________________________________________________ Regency Horizon and SureFire are trademarks of FPI Fireplace Products International Ltd.
© Copyright 2014, FPI Fireplace Products International Ltd. All rights reserved.
Printed in Canada
Download PDF
Similar pages