Catalogue 2012
1
2
Catalogue 2012
New Products 2012......................................................................................................... 4 - 5
GTi Pro LITE..................................................................................................................... 6 - 7
GTi Pro HVLP and Trans-Tech Spray Guns............................................................................ 8 - 9
PRi Pro Trans-Tech Gravity Feed Primer Spray Gun........................................................... 10 - 11
SRi Pro HVLP Spot Repair Gravity Feed Spray Gun ......................................................... 12 - 13
GFG Pro Conventional Gravity Feed Spray Gun.............................................................. 14 - 15
FLG-5 General Purpose Gravity and Suction Feed Spray Guns.......................................... 16 - 17
DAGR Airbrush............................................................................................................ 18 - 19
GTi Pro Compliant Suction and Pressure Feed Spray Guns................................................ 20 - 21
GTi Pro LITE Suction and Pressure Feed Spray Guns......................................................... 22 - 23
JGA Pro Conventional Suction and Pressure Feed Spray Guns........................................... 24 - 25
Pro Clean.................................................................................................................... 26 - 27
DMG Air Dryer Guns and Systems........................................................................................28
DGi Pro Gauges.................................................................................................................29
DeKups....................................................................................................................... 30 - 31
Pro Visor..................................................................................................................... 32 - 33
MPV-627 Air Fed Half Mask Outfit................................................................................. 34 - 35
Valuair and Freedom Half Mask Respirators...........................................................................36
DVFR-1 Filter Regulator........................................................................................................37
DVFR-2 Filter Regulator Coalescer.........................................................................................38
DVFR-3 Filter Regulator........................................................................................................39
DVFR-8 Filter Regulator Coalescer with Activated Carbon Filter.................................................40
Finishline Economy Regulators..............................................................................................41
Accessories - Gravity and Suction Cups.................................................................................42
Accessories - Spray Gun............................................................................................... 43 - 44
Accessories - Hoses and Connections....................................................................................45
KBII 2.3 Litre Remote Cup............................................................................................. 46 - 47
Binks DVP Double Diaphragm Fluid Pump....................................................................... 48 - 49
Binks Air Assisted Airless Pump...................................................................................... 50 - 51
Binks Pressure Feed Tank............................................................................................... 52 - 53
Evercoat Products......................................................................................................... 54 - 55
CVi...................................................................................................................................56
GTiW / GTiG / PRi............................................................................................................57
GTiP / GTiS.......................................................................................................................58
SRi / SRiW........................................................................................................................59
VRiS & P / VRiG.......................................................................................................... 60 - 61
JGAS.................................................................................................................................62
GFG..................................................................................................................................63
MPV-623...........................................................................................................................64
MPV-517...........................................................................................................................65
Conditions of Sale........................................................................................................ 66 - 68
Notes......................................................................................................................... 69 - 70
ATEX.................................................................................................................................71
Catalogue 2012
3
GTi Pro LITE and Pro LITE Digital
A lightweight gun that delivers heavyweight performance...
Resplendent in a bright gold, deep anodised metallic finish the GTi Pro LITE
and Pro LITE Digital become the latest members of the “i-system pro” gun family
alongside the SRi Pro SMART repair gun, the PRi Pro Primer gun and of course
it’s big brother the GTi Pro DIGITAL.
Unlike previous mid-size guns the Pro LITE
features full size air caps and shares the same
fluid tips as the GTi Pro. Developed for busy
professional painters who require the ultimate
in quality finishes. A range of three advanced
technology air caps (one HVLP and two High
Efficiency) for optimum application performance
with the latest solvent and waterborne coatings
are available.
AVAILABLE
SPRING 2012
All new ergonomic gun body design with even
better fit and balance for comfort and control.
The three high efficiency fluid tips provide superb
versatility across a range of climatic conditions and
viscosities. Coaxial, low kick air valve design gives
smoother feel for even greater air and paint control
for ease of fade-outs and blend-ins. Simplified, user
friendly components provide faster, easier cleaning
and maintenance.
SEE PAGE 6.
The Pro Visor
The Pro Visor is the world’s first air fed respirator to be designed specifically for
the paint spraying industry and not just for personal protection. The technically
advanced design provides the perfect combination of safety and comfort in the
spray booth, with excellent freedom of movement.
The Pro Visor disperses breathing air gently around the lightweight visor at a
positive pressure with no misting or discomfort, ensuring every sprayer can
work at their best. The wrap around visor provides excellent and much wider
peripheral vision than sprayers will be used to, while the removable peak can
help reduce glare from spray booth lighting. There is also plenty of room to
cater for sprayers who wear spectacles.
Perfect fit is vital to a sprayer’s comfort and ensures they perform to the best
of their ability, that’s why the Pro Visor is the first to be designed with a three
dimensional, adjustable and anti-static head band.
This means the Pro Visor can be re-sized for the head circumference, via the
rear knob, the sprayer’s head height can be adjusted at the top of the head
band, while head width can be changed be using a set of three spacers.
The innovative design of the waist belt fitment ensures the single air supply line for both breathing air and spraying air can
be used on either the sprayer’s left or right side, while the wide air connection configuration means the supply hose is pointed
away from the spray area. Professional refinishers using the Pro Visor system will appreciate that the spray gun supply hose
swivels both radially and laterally, ensuring better spray dynamics without the hose restricting the sprayer’s movement, while the
waist belt filter element can be removed and replaced in seconds.
SEE PAGE 32.
4
Catalogue 2012
Pro Clean
Pro Clean is the latest addition to the Pro System and represents a
quantum leap in spray gun cleaning technology. It’s faster, cleaner,
more efficient, highly effective, and significantly reduces solvent use and
wastage when compared to traditional spray gun cleaning machines.
It takes on average, just 20 seconds to clean a spray gun using Pro
Clean.
All you do is remove the paint cup, connect the gun to the airline and
position the gun in the Pro Clean unit. Trigger for 3-4 seconds, the
cleaning fluid in the aerosol is pumped through the paint cup adaptor,
the gun is triggered to clear all the fluid passages of any paint residue.
After cleaning the cap using the same system and another blow through,
using the integral air system the gun is clean and ready for the next job.
Solidly constructed in stainless steel, the compact Pro CLEAN unit can
be wall mounted to maximise floor space in the mixing room and can
be used for either solvent borne and waterborne materials. The aerosol
cleaning fluids for solvent (colour coded orange) and waterborne (colour
coded blue) are simply dropped into the holder in the top of the machine
and one 500 ml can will clean up to 32 spray guns.
SEE PAGE 26.
GTi Pro LITE Suction and Pressure - AVAILABLE SPRING 2012
Designed specifically for the commercial vehicle market the GTi PRO LITE suction and pressure
feed spray guns make light work of heavy vehicles thanks to the new ergonomic gun body
design and full sized air caps.
We’ve taken the tried and tested coaxial, low kick air
valve design from the gravity Pro Lite and incorporated
it into the design of the suction and pressure guns. The
new design produces a much smoother trigger action
providing greater air and fluid control.
It’s lighter too thanks to the new body design and weight
saving aluminium control knobs and air cap retaining ring.
Another new feature to the Pro LITE Suction and Pressure
is the “Quick Clean” coating. This highly durable coating
is ideal for the tough commercial vehicle market where the
guns could be prone to knocks and scratches under chassis
and wheel arches. Along with its durability you’ll also find
it’s quicker to clean too.
SEE PAGE 22.
Images of GTi Pro LITE Suction & Pressure guns are computer generated and for illustration purposes only - not actual guns. Details on our website as soon as available.
Catalogue 2012
5
DIGITAL AVAILABLE
SPRING 2012
A new lightweight DeVilbiss spray gun developed for busy professional painters
needing the ultimate in quality finishes.
Range of three advanced technology air caps (one HVLP and two High Efficiency) for optimum
application performance with the latest solvent and waterborne coatings.
All new ergonomic gun body design with even better fit and balance for comfort and control.
Three high efficiency fluid tips provide superb versatility across a range of climatic conditions
and viscosities.
Coaxial, low kick air valve design gives smoother feel for even greater air and paint control
for ease of fade-outs and blend-ins.
Simplified, user friendly components provide faster, easier cleaning and maintenance.
art Number Explanation
P
PROL - TE10 - B - 13
Model
HV30 HVLP
Air Cap
Air Cap
Base
TE10 High Efficiency
Air Cap
Specification
Air Inlet Pressure
Air Consumption
Air Inlet Thread
2.0 bar (29psi) for TE Caps
1.75 bar (25 psi) for HV Cap
TE10: 270 l/min (9.5 cfm)
TE20: 360 l/min (12.7 cfm)
HV30: 460 l/min (16.3 cfm)
1/4” Universal
Fluid Tip
TE20 High Efficiency
Air Cap
Cup Capacity
Weight (gun only)
Weight (gun & cup)
Air Cap
Air Cap Retaining Ring
Fluid Tip
Fluid Needle
560 mls
446 gms
620 gms
Plated Brass
Clear Anodised Aluminium
Stainless Steel
Stainless Steel
GTiPro LITE Spray Gun Kits
When ordering please specify the air cap of your choice (HV30, TE10, TE20), the tip size of your choice (12, 13 or 14) and the
paint type marking required on your gun B=BASE, C=CLEAR.
Part No Examples Description
PROL-TE10C-13
GTiPro LITE kit with TE10 High Efficiency air cap, #13 fluid tip, marked as “Clear”
PROL-HV30B-D-12
Digital GTiPro LITE kit with HV30 High Efficiency air cap, #12 fluid tip, marked as “Base”
- available Spring 2012
Kit includes GTi Pro LITE gun, gravity cup, paint filter, brush, torx key, set of 4 identification rings and combination spanner
MPV-60-K3
Accessories
Part No
PRO-102-HV30-K
PRO-102-TE10-K
PRO-102-TE20-K
PROL-455-****-**
PRO-200-**-K
PRO-301-K
PRO-470
SN-406
DGIPRO-502-BAR
DGIPRO-504-K
MPV-60-K3
HAF-507-K12
4900-5-1-K3
KGP-5-K5
6
Description
HV30 HVLP Air Cap and retaining ring
TE10 High Efficiency Air Cap and retaining ring
TE20 High Efficiency Air Cap and retaining ring
Air cap, fluid tip and needle kit
Fluid Nozzle Size Numbers 12, 13 & 14
Pro LITE Fluid Needle
Spray Gun Service/Repair Kit
Gun wrench, Torx & flat back screwdriver, cleaning brush and colour ID rings
Digital gauge for air inlet fitting - Reads in bars
Digital gauge for spreader valve assembly for GTiPro LITE - reads in bars
- available Spring 2012
Pack of three male quick detach uni swivel - fits to gun air inlet
Lightweight in-line air filter (pack of 12).
Pack of three cleaning brushes
Pack of 5 gravity cup filters for GFC cups
HAF-507-K12
PRO-470
**** = Air Cap
** = Fluid tip size
Catalogue 2012
Ref
No
1
2
3
4
5
6
7
8
9
10
11
12
13
Description
Air Cap Retaining Clip
TE10 High Efficiency Air Cap & Ring
TE20 High Efficiency Air Cap & Ring
HV30 HVLP Air Cap & Ring
Air Cap Retaining Ring & Seals
Fluid Nozzle 12, 13 or 14
Spray Head Seal (kit of 2)
Spray Head & Seal Kit
Fluid Needle
Fluid Adjusting Knob
Spreader Valve Assembly
Packing, Spring & Packing Nut Kit
Needle Spring Kit
Trigger, Stud & Screw Kit
Air Inlet
Catalogue 2012
Part Number
JGA-156-K5
PRO-102-TE10-K
PRO-102-TE20-K
PRO-102-HV30-K
PRO-420-K
PRO-200**-K
SN-18-1-K2
SN-69-K
PRO-301-K
SN-67-C-K
PRO-406-K
SN-404-K
PRO-472-K3
SP-617-CR-K
SN-9-K
Ref Description
No
14 Colour ID Ring Kit (4 Colours)
15 Airflow Valve (Cheater)
16 Air Valve Kit
17 Body Housing
18 Gravity Cup Kit
19 Drip Check Lid (kit of 5)
20 Gravity Cup Lid
21 Filter
22 Torx Key & Spanner
23 Torx Key
Service Parts
Spray Gun repair kit
Seal and Pin Kit, kit of 5
Circlip, Kit of 5
Part Number
SN-26-K4
PRO-407-K
PRO-471
SN-66-K
GFC-501
GFC-2-K5
GFC-402
KGP-5-K5
SN-406
SPN-8-K2
PRO-470
GTI-428-K5
25746-007-K5
7
High Performance, Base and
Clearcoat Technology Spray guns
A totally new DeVilbiss spray gun developed for busy professional painters needing the
ultimate in quality finishes.
The gun can be purchased with or without the DGi Pro pod Digital gauge factory fitted (this
gauge can also be retrofitted to standard guns).
Four advanced technology air caps (one HVLP and three Trans-Tech) for optimum
application performance with the latest solvent and waterborne coatings.
All new ergonomic gun body design with even better fit and balance for comfort
and control.
New ultra high flow fluid tips provide superb versatility across a range of viscosities.
Revolutionary air valve design gives smoother feel for even greater air and
paint control for ease of fade-outs and blend-ins.
Simplified, user friendly components provide easy cleaning and maintenance.
art Number Explanation
P
GTIPRO - T1 - B - D - 13
Model
No H1 HVLP
Air Cap
Air Cap
BaseDigital Models Fluid Tip
No T1 Trans-Tech
Air Cap
Specification
Air Inlet Pressure
Air Consumption
Air Inlet Thread
2.0 bar (29psi)
T1: 280 l/min (9.9 cfm)
T2: 350 l/min (12.4 cfm)
H1 450 l/min (15.9 cfm)
T110: 265 l/min (9.4 cfm)
1/4” Universal
No T2 Trans-Tech
Air Cap
Cup Capacity
Weight (gun & cup)
Digital Weight (gun & cup)
Air Cap & Ring
Fluid Tip
Fluid Needle
No T110 Trans-Tech
Air Cap
560 mls
768 gms
823 gms
Plated Brass
Stainless Steel
Stainless Steel
GTi Pro Spray Gun Kits
When ordering please specify the air cap of your choice (H1, T1 or T2), the tip size of your choice (12, 13 or 14) and the paint type
marking required on your gun B=BASE, C=CLEAR and add in a –D if you require the gun complete with digital pod gauge.
DGIPRO-503-BAR-K
Part No Examples Description
GTIPRO-T1C-13
Gun with a T1 Trans-Tech air cap, a #13 fluid tip and marked as “CLEAR”
GTIPRO-H1B-D-12
Digital Gun with a H1 HVLP air cap, a #12 fluid tip and marked as “BASE”
Kit includes GTi PRO Gravity gun, cup, paint filter, brush, set of 4 identification rings and combination spanner
Accessories
Part No
PRO-100-H1-K
PRO-100-T1-K
PRO-100-T2-K
PRO-100-T110-K
PRO-450-***-**
PRO-200-**-K
PRO-300-K
PRO-415-1
SN-406
DGIPRO-502-BAR
DGIPRO-503-BAR-K
MPV-60-K3
HAF-507-K12
4900-5-1-K3
KGP-5-K5
PRO-15-K3
8
Description
H1 HVLP Air Cap and retaining ring
T1 Trans-Tech Air Cap and retaining ring
T2 Trans-Tech Air Cap and retaining ring
T110 Trans-Tech Air Cap and retaining ring
Air cap, fluid tip and needle kit
Fluid Nozzle Size Numbers 12, 13 & 14
Fluid Needle
Spray Gun Service/Repair Kit
Gun wrench, Torx & flat back screwdriver, cleaning brush and colour ID rings
Digital Gauge - Reads in bars
Digital gauge for spreader valve assembly for GTiPro - reads in bars
Male Quick Detach Uni Swivel - fits to gun air inlet
Lightweight in-line air filter (pack of 12)
Pack of three cleaning brushes
Pack of 5 gravity cup filters for GFC cups
ProClip - snap on trigger locking clip
MPV-60-K3
HAF-507-K12
PRO-415-1
*** = Air Cap
** = Fluid tip size
Catalogue 2012
Ref
No
Description
Part Number
Ref
No
Description
Part Number
1
Air Cap Retaining Clip
JGA-156-K5
14
Air Inlet
SN-40-K
2
T1 Trans-tech Aircap & Ring
PRO-100-T1-K
15
Colour ID Ring Kit (4 Colours)
SN-26-K4
T2 Trans-tech Aircap & Ring
PRO-100-T2-K
16
Airflow Valve
PRO-411-K
H1 HVLP Aircap & Ring
PRO-100-H1-K
17
Baffle plate
SN-41-K
3
Air Cap Retaining Ring & Seals
PRO-405-K
18
Gravity Cup Kit
GFC-501
4
Fluid Nozzle – 12, 13, 14
PRO-200-**-K
19
Drip Check Lid (kit of 5)
GFC-2-K5
5
Spray Head Seal (kit of 2)
SN-18-1-K2
20
Gravity Cup Lid
GFC-402
6
Spray Head & Seal Kit
SN-17-1-K
21
Filter
KGP-5-K5
7
Body Bushing & Seal
SN-6-K
22
Torx Key
SPN-8-K2
8
Fluid Needle
PRO-300-K
23
Trigger Stud & Torx Screw (kit of 5)
SN-405-K5
9
Fluid Adjusting Knob, Spring & Pad Kit
PRO-3-K
24
Needle spring and pad kit
SN-4-K3
10
Spreader Valve Assembly
PRO-402-K
25
Air valve seal & service tool
SN-34-K5
11
Packing, Spring & Packing Nut Kit
SN-404-K
Service Parts
12
Air Valve Replacement Kit
SN-402-K
Spray Gun repair kit
PRO-415-1
13
Trigger, Stud & Screw Kit
SN-21-K
Seal and Pin Kit, kit of 5
GTI-428-K5
®
®
Catalogue 2012
9
HIGH PERFORMANCE, GRAVITY FEED,
PRIMER SPRAY GUN
Advanced technology P1 Trans-Tech Air Cap.
Suitable for all primers including latest generation waterbase materials.
Fluid Tip sizes available for fillers, surfacers and polyesters.
First class atomisation and material distribution.
Utilises new design air valve for smooth triggering control.
All new ergonomic gun body with improved “fit and feel”.
Large spray patterns for fast and easy application.
Drop forged body with tough anodised finish for protection.
art Number Explanation
P
PRiPRO - P1P - XX
Model
Air Cap
Fluid Tip
Specification
Air Inlet Pressure
2.0 bar (29psi)
Air Consumption
300 l/min (10.6 cfm)
Air Inlet Thread
1/4” Universal
Cup Capacity
560 mls
Weight (gun & cup)
760 gms
Air Cap & Ring
Plated Brass
Fluid Tip
Stainless Steel
Fluid Needle
Stainless Steel
PRi Spray Gun Kits
Part No
Description
PRiPRO-P1P-14
Gravity Gun & Cup – P1 Air Cap & No. 14 Fluid Tip
PRiPRO-P1P-16
Gravity Gun & Cup – P1 Air Cap & No. 16 Fluid Tip
PRiPRO-P1P-18
Gravity Gun & Cup – P1 Air Cap & No. 18 Fluid Tip
PRiPRO-P1P-20
Gravity Gun & Cup – P1 Air Cap & No. 20 Fluid Tip
PRiPRO-P1P-25
Gravity Gun & Cup – P1 Air Cap & No. 25 Fluid Tip
Kit includes PRiPRO Gravity Gun, cup, paint filter, brush and multi-fit spanner
No P1 Trans-Tech
Air Cap
DGIPRO-502-BAR
Accessories
Part No
Description
PRIPRO-100-P1-K
Air cap and retaining ring
PRIPRO-210-**-K
Fluid Nozzle - Size Numbers 14,16,18, 20 & 25
PRIPRO-310--K
Fluid needle
PRO-415-1
Spray gun repair kit – includes seals, packing and springs
DGIPRO-502-BAR
Digital pressure gauge – reads in bars
HAF-507-K12
Lightweight, in-line air filter (pack of 12)
KGP-5-K5
Pack of gravity cup filters for GFC cups
GFC-501
Replacement gravity cup complete (0.6 litre)
4900-5-1-K3
Pack of three cleaning brushes
MPV-60-K3
Male quick detach Uni swivel stem to fit onto gun air inlet
GFV-50F
Gravity gun bench top stand
GFG-6
Wall mounting bracket for gun and cup
PRO-15-K3
ProClip - snap on trigger locking clip
** = Fluid tip size
10
KGP-5-K5
GFV-50F
MPV-60-K
Catalogue 2012
Ref
No
Description
Part Number
Ref
No
Description
Part Number
1
Air Cap Retaining Clip
JGA-156-K5
15
Colour ID Ring Kit (4 Colours)
SN-26-K4
2
Trans-tech® Aircap
PRIPRO-100-P1-K
16
Airflow Valve
PRO-411-K
3
Air Cap Retaining Ring & Seals
PRO-405-K
17
Baffle plate
SN-41-K
4
Fluid Nozzle – 14, 16, 18, 20, 25
PRIPRO-210-**-K
18
Gravity Cup Kit
GFC-501
5
Spray Head Seal (kit of 2)
SN-18-1-K2
19
Drip Check Lid (kit of 5)
GFC-2-K5
6
Spray Head & Seal Kit
SN-17-1-K
20
Gravity Cup Lid
GFC-402
7
Body Bushing & Seal
SN-6-K
21
Filter
KGP-5-K5
8
Fluid Needle
PRIPRO-310-K
22
Torx Key
SPN-8-K2
9
Fluid Adjusting Knob, Spring & Pad Kit
PRO-3-K
23
Trigger Stud & Torx Screw (kit of 5)
SN-405-K5
10
Spreader Valve Assembly
PRO-402-K
24
Needle spring and pad kit
SN-4-K3
11
Packing, Spring & Packing Nut Kit
SN-404-K
25
Air valve seal & service tool
SN-34-K5
Service Parts
12
Air Valve Replacement Kit
SN-402-K
13
Trigger, Stud & Screw Kit
SN-21-K
Spray Gun repair kit
PRO-415-1
14
Air Inlet
SN-40-K
Seal and Pin Kit, kit of 5
GTI-428-K5
Catalogue 2012
11
COMPLIANT SMART / SPOT REPAIR
GRAVITY FEED SPRAY GUN
Totally redesigned SRi gravity gun for small scale repair work.
New, more ergonomic gun body with improved fit, feel, comfort and controls.
New balanced air valve design for precision control of paint and air.
Three compliant air cap choices to suit all latest refinishing materials.
A range of four nozzle sizes for varying viscosities and control preferences.
Renowned DeVilbiss atomisation quality and even paint distribution.
Faster, easier maintenance from user-friendly fittings and adjustments.
Rugged drop forged body with anodised finish for protection.
art Number Explanation
P
SRiPRO - TS1 - 08
Model
Air Cap
Fluid Tip
Specification
Air Consumption:
HS1: 135 l/min (4.8 cfm) @ 2.0 bar (30 psi)
TS1: 100 l/min (3.5 cfm) @ 2.0 bar (30 psi)
RS1: 55 l/min (1.9 cfm) @ 1.0 bar (15psi)
Air inlet thread
1/4” Universal
Cup Capacity
125 mls
Weight (gun & cup)
500 gms
Air cap & ring
Plated Brass
Fluid Nozzle &
Stainless Steel
Needle
Stainless Steel
SRi Pro Gravity Spot Repair Spray Gun Kits
No HS1
Air Cap HVLP
No TS1
Air Cap Trans Tech
(Specify the air cap & nozzle size required)
Part No
Description
SRIPRO-TS1-08
Gravity Feed Gun with TS1 Trans-Tech cap & No. 08 fluid tip
SRIPRO-HS1-10
Gravity Feed Gun with HS1 HVLP cap & size No. 10 fluid tip
Kit contents are spray gun with chosen cap tip set up, permanent and semi-disposable cups, pouring funnel,
spanner, torx key and cleaning brush.
SRIPRO-100-RS1-K
Accessories
12
Part No
Description
SRIPRO-100-HS1-K
HVLP Air Cap and retaining ring
SRIPRO-100-TS1-K
Trans-Tech Air Cap and retaining ring
SRIPRO-100-RS1-K
Round spray (hornless) cap - priming, pinstriping
SRIPRO-200-**-K
Fluid Nozzles - Sizes No. 08, No. 10, No. 12 & No. 14
SRIPRO-300-08-10-K
Fluid Needle for No. 08 & No. 10 fluid nozzles
SRIPRO-300-12-14-K
Fluid Needle for No. 12 & No. 14 fluid nozzles
SPN-8-K2
Torx & flat blade Screwdriver - Trigger & Needle Packing
MPV-60-K3
Male Quick Detach Uni Swivel - fits to gun air inlet
SRi-65-K2
Pack of two cleaning brushes
PRO-415-1
SRi service kit – includes seals, packing and springs
SRi-510
125ml Acetal gravity cup
SRi-51-K12
Pack of 12 SRi cup pouring funnels
SRi-478-K12
Pack of 12 SRi Gravity Cups & 12 coloured lids
SRi-480-K3
Black cup and lid for UV paint – Pack of 3
SRi-42-K3
Pack of 3 cone filters
DGIPRO-502-BAR
Digital Gauge - Reads in bars
SPN-8-K2 &
SRi-50-K2
MPV-60-K3
DGiPRO-502-BAR
Catalogue 2012
Ref.
No
Description
Part No.
Ref.
No
Description
Part No.
1
HVLP Air Cap & Ring
SRIPRO-100-HS1-K
12
Air Inlet
SN-40-K
Trans-Tech Air Cap & Ring
SRIPRO-100-TS1-K
13
Colour ID Ring Kit (4 Colours)
SN-26-K4
Round Spray Air Cap & Ring
SRIPRO-100-RS1-K
14
Airflow Valve
PRO-404-K
2
Fluid Nozzle (** = 08, 10, 12 or 14)
SRIPRO-200-**-K
15
Gravity Cup Kit
SRI-510
3
Separator
SRIPRO-2-K5
16
Filter
SRI-42-K3
Fluid Needle for No. 08 & No. 10 Fluid
Nozzles
SRIPRO-300-08-10-K
17
Drip Check Lid (kit of 5)
GFC-2-K5
18
Funnel kit of 12
SRI-51-K12
Fluid Needle for No. 12 & No. 14 Fluid
Nozzles
SRIPRO-300-12-14-K
19
Spanner kit of 2
SRI-50-K2
5
Fluid Adjusting Knob, Spring & Pad Kit
PRO-3-K
20
Torx Key
SPN-8-K2
21
Needle spring and pad kit
SN-4-K3
6
Spreader Valve Assembly
SRIPRO-401-K
22
Air valve seal & service tool
SN-34-K5
7
Body Bushing & Seal
SN-6-K
23
Gravity Cup Lid
SRI-414-K2
8
Packing, Spring & Packing Nut Kit
SN-404-K
Service Parts
9
Air Valve Assembly
SN-402-K
10
Stud and Screw kit
SN-405-K5
11
Trigger, Stud & Screw Kit
SN-42-K
4
Catalogue 2012
Seal and Pin Kit, kit of 5
GTI-428-K5
Spray gun repair kit - includes seals, packing PRO-415-1
and springs
13
PROFESSIONAL Conventional Gravity Feed
Spray Gun
Totally redesigned GFG gun for professional use.
Renowned DeVilbiss atomisation quality and even paint distribution.
Utlises new air valve design for ultra smooth triggering and control.
Rugged drop forged body with anodised finish for protection.
A choice of two advanced technology air caps to suit solids and metallics.
Three fluid tip sizes for varying viscosities and control preferences.
New, more ergonomic gun body with improved fit, feel, comfort and control.
Faster, easier maintenance from user-friendly fittings and adjustments.
art Number Explanation
P
GFGPRO - C1 - XX
Model
Air Cap
Fluid Tip
No C1
Air Cap
No C2
Air Cap
Specification
Air Inlet Pressure
Air Consumption
Air Inlet Thread
C1: 2.5 - 3.0 bar (30 - 45 psi)
C2: 2.5 - 4.0 bar (30 - 60 psi)
C1: 300 l/min (10.6 cfm) @ 3.0 bar
C2: 305 l/min (12.8 cfm) @ 3.0 bar
1/4” Universal
Cup Capacity
Weight (gun & cup)
Air Cap & Ring
Fluid Tip
Fluid Needle
560 mls
768 gms
Plated Brass
Stainless Steel
Stainless Steel
GFG-Pro Spray Gun Kits
DGIPRO-502-BAR
When ordering please specify the air cap of your choice (C1 or C2) and the tip size of your choice (14, 16 or 18).
Part No Examples Description
GFGPRO-C1-14
Gravity Gun & Cup - C1 air cap and No. 14 fluid tip
GFGPRO-C1-16
Gravity Gun & Cup - C1 air cap and No. 16 fluid tip
GFGPRO-C2-18
Gravity Gun & Cup - C2 air cap and No. 18 fluid tip
Kit includes GFG PRO Gravity gun, cup, paint filter, brush and multi-fit spanner
MPV-60-K3
Accessories
Part No
PROC-120-C1-K
PROC-120-C2-K
PROC-220-**-K
GFGPRO-320-K
PRO-415-1
SPN-8-K2
SN-406
DGIPRO-502-BAR
MPV-60-K3
HAF-507-K12
4900-5-1-K3
KGP-5-K5
PRO-15-K3
14
Description
C1 Air Cap and retaining ring
C2 Air Cap and retaining ring
Fluid Nozzle Size Numbers 14, 16 & 18
Fluid Needle
Spray Gun Service/Repair Kit
Torx & flat blade Screwdriver - Trigger & Needle Packing
Gun wrench, Torx & flat back screwdriver, cleaning brush and colour ID rings
Digital Gauge - Reads in bars
Male Quick Detach Uni Swivel - fits to gun air inlet
Lightweight in-line air filter (pack of 12)
Pack of three cleaning brushes
Pack of 5 gravity cup filters for GFC cups
ProClip - snap on trigger locking clip
HAF-507-K12
PRO-415-1
** = Fluid tip size
Catalogue 2012
Ref
No
Description
Part Number
Ref
No
Description
Part Number
1
Air Cap Retaining Clip
JGA-156-K5
14
Air Inlet
SN-40-K
2
C1 Aircap & Ring
PROC-120-C1-K
15
Colour ID Ring Kit (4 Colours)
SN-26-K4
C2 Aircap & Ring
PROC-120-C2-K
16
Airflow Valve
PRO-411-K
3
Air Cap Retaining Ring & Seals
PRO-405-K
17
Baffle plate
SN-41-K
4
Fluid Nozzle
PROC-220-**-K
18
Gravity Cup Kit
GFC-501
5
Spray Head Seal (kit of 2)
SN-18-1-K2
19
Drip Check Lid (kit of 5)
GFC-2-K5
6
Spray Head & Seal Kit
SN-17-1-K
20
Gravity Cup Lid
GFC-402
7
Body Bushing & Seal
SN-6-K
21
Filter
KGP-5-K5
8
Fluid Needle
GFGPRO-320-K
22
Torx Key
SPN-8-K2
9
Fluid Adjusting Knob, Spring & Pad Kit
PRO-3-K
23
Trigger Stud & Torx Screw (kit of 5)
SN-405-K5
10
Spreader Valve Assembly
PRO-402-K
24
Needle spring and pad kit
SN-4-K3
11
Packing, Spring & Packing Nut Kit
SN-404-K
25
Air valve seal & service tool
SN-34-K5
12
Air Valve Replacement Kit
SN-402-K
Service Parts
13
Trigger, Stud & Screw Kit
SN-21-K
Catalogue 2012
Spray Gun repair kit
PRO-415-1
Seal and Pin Kit, kit of 5
GTI-428-K5
15
FLG-5
General Purpose Spray Gun
General purpose compliant spray gun for a wide range of refinish
paints and coatings.
Operates with unique and efficient DeVilbiss Trans-Tech®
Atomisation Technology.
Ergonomically shaped gun handle for positive grip and comfort.
Smooth action trigger with exceptionally light pull for fatigue free
operation.
Ultra lightweight but strong, cast aluminium gun body.
Full controls of pattern shape, fluid flow rate and air inlet pressure.
Precision engineered brass air cap and stainless steel fluid tips.
Choice of gravity or suction models with large capacity cups.
NOT SUITABLE FOR USE WITH WATERBORNE MATERIALS.
art Number Explanation
P
FLG - G5 - 14
ModelGravity/Air Cap
Fluid Tip
Specification
Air inlet Pressure
2.0 bar (29 psi) – Suction & Gravity
Air Consumption
277 l/min (9.8 cfm)
Air Inlet Thread
1⁄4” Universal
Cup Capacity
Gravity 560 mls, Suction 1140 mls
Weight (gun & cup)
Gravity 642 gms, Suction 934 gms
Air Cap
Plated brass
Retaining Ring
Plated brass
Fluid Tip
Stainless Steel
Fluid Needle
Stainless Steel
FLG-5 Air Cap
FLG-5 Spray Gun Kit
Part No
Description
FLG-G5-14
Gravity Gun & Cup Kit – No 5 Air Cap & 1.4 mm Fluid Tip
FLG-G5-18
Gravity Gun & Cup Kit – No 5 Air Cap & 1.8 mm Fluid Tip
FLG-S5-18
Suction Gun & Cup Kit – No 5 Air Cap & 1.8 mm Fluid Tip
HAV-501-B
Spares and Accessories
Part No
Description
FLG-0001-5
No 5 Trans-Tech Air Cap (Fits Gravity & Suction)
SGK-0023
Air Cap Retaining Ring
SGK-0012-14
1.4 mm fluid tip for gravity gun
SGK-0012-20
2.0 mm fluid tip for gravity gun
SGK-0014-18
1.8 mm fluid tip for suction and gravity guns
SGK-0430-18
Fluid Needle (for 1.8 mm tip – Suction Gun)
SGK-0420
Fluid Needle (for 2.0 mm tip – Gravity Gun)
SGK-0418
Fluid Needle (for 1.8 mm tip – Gravity Gun)
SGK-0414
Fluid Needle (for 1.4mm - Gravity Gun)
SGK-0043-K10
Fluid Tip seal (pack of 10)
K-5030
Baffle Replacement Kit
K-5040
Repair kit – seals and springs – includes service tool
KGP-5-K5
Pack of gravity cup filters for GFC cup
MPV-60-K3
Male, quick detach, universal swivel – fits to gun air inlet
4900-5-1-K3
Pack of three cleaning brushes
KK -4584
Spray gun cleaning tool kit – purpose made brushes & tools
SGK-0537
Needle Packing
16
KK-4584
KGP-5-K5
GFV-50F
Catalogue 2012
Ref Description - Suction Gun
No
Part Number
Ref Description - Gravity Gun
No
Part Number
1
Retaining ring
SGK-0023
1
Retaining ring
SGK-0023
2
Air cap
FLG-0001-5
2
Air cap
FLG-0001-5
3
Fluid tip 1.4mm, Fluid tip 1.8mm
SGK-0012-14
SGK-0014-18
3
Fluid tip 1.8mm
SGK-0014-18
4
Gasket
SGK-0043-K10* •
5
Baffle
*•
6
Packing
*
7
U-cup seal
*
8
Air-valve seat
*
9
Air-valve stem
*
10
Air-valve spring
*
11
Fluid needle 1.8mm
SGK-0430-18
12
Assembly tool
*
*
Seal, baffle and gasket replacement kit, items
4, 5, 6, 7, 8, 9, 10, and 17
K-5040
Baffle replacement kit, items 4 and 5
K-5030
•
Catalogue 2012
Fluid tip 2.0mm (available separately)
SGK-0012-20
4
Gasket
SGK-0043-K10* •
5
Baffle
*•
6
Packing
SGK-0537*
7
U-cup seal
*
8
Air-valve seat
*
9
Air-valve stem
*
10
Air-valve spring
11
Fluid needle 1.4mm
SGK-0414
Fluid needle 1.8mm
SGK-0418
Fluid needle 2.0mm (available separately)
SGK-0420
12
Filter
KGP-5-K5
13
Lid assembly
GFC-402
14
Drip free vent lid kit of 5
GFC-2-K5
15
Cup assembly
GFC-501
16
Assembly tool
*
*
Seal, baffle and gasket replacement kit, items
4, 5, 6, 7, 8, 9, 10, and 16
K-5040
•
Baffle replacement kit, items 4 and 5.
K-5030
*
17
GRAVITY FEED AIRBRUSH
PERFORMANCE & VERSATILITY
FOR AUTOMOTIVE ARTISTS
Sprays most automotive
paints and lacquers.
Hairline detail to high
paint-flow shading and
gradual fades.
Lightweight, well balanced
with smooth double action
trigger.
Crown cap standard for fine lines
and needle protection.
Copper, nickel and chrome plated body.
Pre-set handle for precise control of paint
flow.
Removable 9 mls (1/3rd oz) gravity cup.
Solvent proof fluid passages, Teflon® needle packing.
Precision made and hand tested in the U.S.A.
Part Number
Specification
DGR - 501G - 35
Operating Pressure
1.3 – 3.5 bar (20 -50 psi)
Max inlet pressure
12 bar (175 psi)
Fluid tip
0.35mm
Cup Capacity
9 mls (1/3 fl/oz)
Airbrush plating
Nickel, copper, chrome
Needle Packing
Teflon®(solvent proof)
Hose: Inside diameter
3.2 mm (1/8”)
Air Hose connection
1⁄4” NPS (M)
Universal fluid threaded
connector
3/8”
DAGR Airbrush Kit and Accessories
18
Part No
Description
DGR-501G-35
DAGR Gravity Airbrush - 0.65mm – 9 CC Cup/lid (1/3 fl/oz)
DGR-123
3 m (10’) Braided Nylon Air Hose with loose nut 1⁄4” swivel connections.
DGR-121K
Repair Kit - ‘O’ Rings, needle spring and washers
DGR-124
3m (10’) Braided Air Hose with QD
Catalogue 2012
Description
Part No.
Ref.
No.
Description
Part No.
1
Crown cap
DGR-101
14
Spring guide
DGR-111
2
Air cap (for .35mm nozzle)
DGR-103-35
15
Needle locknut
DGR-112
3
Head cap
DGR-104
16
Needle (for .35mm nozzle)
DGR-113-35
17
Cutaway handle w/pre-set
DGR-114
O-ring (pre-set needle knob)
-
Ref.
No.
4
Nozzle (.35mm)
DGR-105-35
*5
O-ring (head cap & handle)
-
6
Packing and nut assembly (Teflon)
DGR-106K
19
Pre-set needle knob
DGR-116
1/4 oz.(7 cc) cup and lid
DGR-117
* 18
7
Air valve casing
DGR-107
20
8
Air valve kit
DGR-108K
21
1/3 oz.(9 cc) cup and lid (standard)
DGR-118
*9
Air valve washer
-
22
1/2 oz.(14 cc) cup and lid
DGR-119
10
Trigger assembly
DGR-109
23
Cup lid
DGR-120
11
Trigger buttons ergo-pack (4 types)
DGR-122K
Repair Kit
12
Needle guide, rocker, & spring
DGR-110K
* 13
Needle spring
-
Catalogue 2012
DAGR repair kit - includes item numbers 5, 9,
13 & 18
DGR-121K
19
COMPLIANT Suction & PRESSURE
Feed Spray GunS
Totally redesigned GTi Pro gun for suction or pressure feed duty. New, more ergonomic gun body with improved fit, feel, comfort and controls.
Suitable for use with a suction cup or pumps, tanks or remote feed cups.
Four compliant air cap choices to suit solids, metallics, bases and clears.
A range of pressure & suction nozzle sizes for varying viscosities and control preferences.
Utilises new air valve design for ultra smooth triggering and control.
Renowned DeVilbiss atomisation quality and even paint distribution.
Faster, easier maintenance from user-friendly fittings and adjustments.
Rugged drop forged body with anodised finish for protection.
art Number Explanation
P
GTISPRO (or GTIPPRO) - T1 - XX
Model
Air Cap
No T1 Trans-Tech
Air Cap
No H1 HVLP
Air Cap
Fluid Tip
No T2 Trans-Tech
Air Cap
No T4 Trans-Tech
Air Cap
GTiP-Pro only
Specification
Air Inlet Pressure
Air Consumption
 
 
 
Air inlet thread
Fluid inlet thread
H1, T1, T2, T3 & T4 air caps 2.0 bar (30 psi)
H1: 450 l/min (16 cfm) @ 2.0 bar (30 psi)
T1: 280 l/min (10 cfm) @ 2.0 bar (30 psi)
T2: 350 l/min (12 cfm) @ 2.0 bar (30 psi)
T4: 330 l/min (11.7 cfm) @ 2.0 bar (30 psi)
450 l/min (15.9 cfm) @ 3.0 bar (44 psi)
Universal 1/4” BSP/NPS
Universal 3/8” BSP/NPS
Max static air inlet
pressure
Max static fluid inlet
pressure
Air cap & ring
Fluid Nozzle & Needle
Suction gun & cup weight
Pressure gun weight
P1 = 12 bar (175 psi)
P2 = 14 bar (203 psi)
Plated Brass
Stainless Steel
1070 gms
650 gms
GTi Pro Suction / Pressure Spray Gun Kits
When ordering please specify the air cap and nozzle size required.
Part No Examples
Description
GTISPRO-T1-16
Suction Feed Gun with T1 air cap and No. 16 fluid nozzle
GTIPPRO-T2-085
Pressure Feed Gun with T2 air cap and No. 085 fluid nozzle
DGIPRO-502-BAR
GTI Pro kits include: suction cup with filter (suction kits only), cleaning brush, torx key, set of 4 identification rings
and combination spanner
Accessories
Part No
Description
PRO-100-H1-K
HVLP Air Cap and retaining ring
PRO-100-T1-K
Trans-Tech Air Cap and retaining ring
PRO-100-T2-K
Trans-Tech Air Cap and retaining ring
PRO-100-T4-K
Trans-Tech Air Cap and retaining ring
PRO-200-**-K
Suction/Pressure Fluid Nozzles- Size Numbers 16, 18 & 20
PRO-315-K
Suction/Pressure Fluid Needle for 16, 18 & 20 Nozzle sizes
PRO-205-**-K
Pressure Fluid Nozzle Size Numbers 085, 10, 12 & 14
PRO-305-085-10-K
Pressure Fluid Needle for 085 & 10 Nozzle sizes
PRO-305-12-14-K
Pressure Fluid Needle for 12 & 14 Nozzle sizes
PRO-415-1
Spray Gun Service/Repair Kit
SPN-8-K2
Torx & flat blade Screwdriver - Trigger & Needle Packing
DGIPRO-502-BAR
Digital Gauge - Reads in bars
MPV-60-K3
Male Quick Detach Uni Swivel - fits to gun air inlet
HAF-507-K12
Lightweight in-line air filter.
4900-5-1-K3
Pack of three cleaning brushes
MPV-60-K3
KR-484-K10
** = Fluid tip size
PRO-415-1
20
Catalogue 2012
Ref.
No.
Description
Part No.
Ref.
No.
Description
Part No.
1
Air Cap Retaining Ring
PRO-405-K
16
Air Inlet
SN-40-K
Colour ID Ring Kit (4 Colours)
SN-26-K4
2
Air Cap Retaining Clip
JGA-156-K5
17
3
Aircap & Ring
See page 20
18
Airflow Valve
PRO-411-K
4
Fluid Nozzle
See page 20
19
Stud and Screw kit
SN-405-K5
5
Baffle Plate
SN-41-K
20
Torx Key
SPN-8-K2
6
Spray Head Seal (kit of 2)
SN-18-1-K2
21
Fluid Inlet Connector Kit
PRO-12-K
7
Spray Head & Seal Kit
SN-17-1-K
22
Cup Lid Assembly
KR-4001-B
8
Body Bushing & Seal
SN-6-K
23
Lid Gaskets - kit of 3
KR-11-K3
9
Fluid Needle
See page 20
24
Drip Free Diaphragms - Kit of 5
KR-115-K5
10
Fluid Adjusting Knob, Spring & Pad Kit
PRO-3-K
25
Cup Only
KR-466-K
11
Spreader Valve Assembly
PRO-404-K
26
Complete Cup Assembly
KR-566-1-B
12
Packing, Spring & Packing Nut Kit
SN-404-K
27
Needle spring and pad kit
SN-4-K3
Service Parts
13
Air Valve Seal
SN-34-K5
14
Air Valve Assembly
SN-402-K
Spray Gun repair kit
PRO-415-1
15
Trigger, Stud & Screw Kit
SN-21-K
Seal and Pin Kit, kit of 5
GTI-428-K5
Catalogue 2012
21
2012
G
N
I
R
P
S
E
AVAILABL
The new lightweight gun but redesigned for suction or pressure feed duty.
All new ergonomic gun body design with even better fit and balance for comfort and control.
A range of pressure & suction nozzle sizes for varying viscosities and control preferences.
Four compliant air cap choices to suit all materials and coatings.
Utilises new coaxial air valve design for ultra-smooth triggering and control.
Renowned DeVilbiss atomisation quality and even paint distribution.
Faster, easier maintenance from user-friendly fittings and adjustments.
Rugged drop forged body with the new tough, durable “Quick Clean” coating.
art Number Explanation
P
PROSL - TE10 - 18
Model
TE10 High Efficiency
Air Cap
Air Cap Fluid Tip
TE20 High Efficiency
Air Cap
Specification
Air Inlet Pressure
Air Consumption
Air Inlet Thread
Fluid Inlet Thread
Max Static air inlet
pressure
Max Static fluid inlet
pressure
2.0 bar (29psi)
TE10: 270 l/min (9.5 cfm)
TE20: 360 l/min (12.7 cfm)
TE30: 365 l/min (12.9 cfm)
TE40: 350 l/min (12.4 cfm)
Universal 1/4” BSP/NPS
Universal 3/8” BSP/NPS
P1 = 12 bar (175 psi)
P2 = 15 bar (215 psi)
TE30 High Efficiency
Air Cap
(Pressure only)
Suction Cup Capacity
Weight (gun only)
Weight (gun &
suction cup)
Air Cap
Air Cap Retaining
Ring
Fluid Tip
Fluid Needle
TE40 High Efficiency
Air Cap
(Pressure only)
1 litre
490 gms
925 gms
Plated Brass
Clear Anodised Aluminium
Images of GTi Pro LITE Suction & Pressure
guns are computer generated and for
illustration purposes only - not actual guns.
Details on our website as soon as available.
Stainless Steel
Stainless Steel
GTiPro LITE Spray Gun Kits
When ordering please specify the air cap of your choice and the tip size of your choice.
Part No Examples Description
PROSL-TE10-16
Suction gun & cup kit with TE10 High Efficiency air cap & #16 fluid tip
PROPL-TE40-10
Pressure gun kit with TE40 High Efficiency air cap & #10 fluid tip
DGIPRO-502-BAR
GTI Pro LITE kits include: suction cup with filter (suction kits only), cleaning brush, torx key, set of 4 identification rings and combination spanner
Accessories
Part No
PRO-102-TE10-K
PRO-102-TE20-K
PRO-102-TE30-K
PRO-102-TE40-K
PRO-200-**-K
PRO-205-**-K
PRO-325-K
PRO-320-085-10-K
PRO-320-12-14-K
PROL-455-****-**
PRO-470
SN-406
DGIPRO-502-BAR
MPV-60-K3
HAF-507-K12
4900-5-1-K3
22
Description
TE10 High Efficiency Air Cap and retaining ring
TE20 High Efficiency Air Cap and retaining ring
TE30 High Efficiency Air Cap and retaining ring
TE40 High Efficiency Air Cap and retaining ring
Fluid Nozzle – Suction feed - Size Numbers 16, 18 & 20
Fluid Nozzle – Pressure feed – Size Numbers (0.85, 1.0, 1.2 & 1.4)
Suction Fluid Needle for 1.6, 1.8 & 2.0
Pressure Fluid Needle for 0.85 & 1.0 nozzle sizes
Pressure Fluid Needle for 1.2 & 1.4 nozzle sizes
Air cap, fluid tip and needle kit
Spray Gun Service/Repair Kit
Gun wrench, Torx & flat back screwdriver, cleaning brush and colour ID rings
Digital gauge for air inlet fitting - Reads in bars
Pack of three male quick detach uni swivel - fits to gun air inlet
Lightweight in-line air filter (pack of 12).
Pack of three cleaning brushes
MPV-60-K3
HAF-507-K12
PRO-470
**** = Air Cap
** = Fluid tip size
Catalogue 2012
Ref
No
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
Description
Air Cap Retaining Ring & Seal
Air Cap Retaining Clip
High Efficiency Aircap & Ring
Fluid Nozzle Kit
Spray Head Seal
Spray Head Kit
Spreader Valve Assembly
Air Valve Kit
Fluid Needle
Housing
Fluid Adjusting Knob
Colour ID Ring Kit (4 Colours)
Needle spring kit
Air Inlet Kit
Packing, spring and packing nut kit
Catalogue 2012
Part Number
PRO-420-K
JGA-156-K5
See Page 22
See Page 22
SN-18-1-K2
SN-69-K
PRO-404-K
PRO-471
See Page 22
SN-66-K
SN-67-C-K
SN26-K4
PRO-472-K3
SN-9-K
SN-404-K
Ref Description
No
16 Trigger, stud & Screw Kit
17 Airflow valve
18 Circlip - kit of 5
19 Fluid inlet kit
Suction Cup Models only
20 Suction cup kit
21 Cup lid gasket - kit of 3
22 Drip check Diaphragm (kit of 5)
23 Filter - kit of 10
24 Lid assembly
25 Cup
Service Parts
26 Tool kit
Spray Gun Repair kit
Seal and Pin Kit, kit of 5
Part Number
SP-617-CR-K
PRO-407-K
25746-007-K5
ADV-7-K
KR-566-1-1B
KR-11-K3
KR-115-K5
KR-484-K10
KR-4001-B
KR-466-K
SN-406
PRO-470
GTI-428-K5
23
PROFESSIONAL Conventional
Suction & PRESSURE Feed Spray Gun
Totally redesigned JGA gun for professional use.
Renowned DeVilbiss atomisation quality and even paint distribution.
Utlises new air valve design for ultra smooth triggering and control.
Rugged drop forged body with anodised finish for protection.
A choice of two advanced technology air caps to suit solids and metallics.
Three fluid tip sizes for varying viscosities and control preferences.
New, more ergonomic gun body with improved fit, feel, comfort and control.
Faster, easier maintenance from user-friendly fittings and adjustments.
art Number Explanation
P
JGASPRO (or JGAPPRO) - C1 - XX
Model
Air Cap
No C2 Air Cap
No C1 Air Cap
Fluid Tip
No C3 Air Cap
Specification
Air Inlet Pressure
Air Consumption
Air Inlet Thread
C1: 2.5 - 3.0 bar (30 - 45 psi)
C2: 2.5 - 4.0 bar (30 - 58 psi)
C3: 2.5 - 4.0 bar (30 - 58 psi)
C1: 300 l/min (10.6 cfm) @ 3.0 bar
C2: 305 l/min (12.8 cfm) @ 3.0 bar
C3: 410 l/min (14.5 cfm) @ 3.0 bar
1/4” Universal
Fluid Inlet Thread
Cup Capacity
Weight (gun & cup, S)
Weight (gun, P)
Air Cap & Ring
Fluid Tip
Fluid Needle
3/8” Universal
1000 mls
1070 gms
650 gms
Plated Brass
Stainless Steel
Stainless Steel
JGA-Pro Spray Gun Kits
When ordering please specify the air cap (C1, C2 or C3) and the tip size of choice (12, 14, 16, 18 or 085).
Part No Examples Description
JGASPRO-C1-16
Suction Feed Gun with C1 air cap and No. 16 fluid tip
JGAPPRO-C3-085
Pressure Feed Gun with C3 air cap and No. 085 fluid tip
JGA Pro kits include: suction cup with filter (suction kits only), cleaning brush, torx key, set of 4 identification rings
and combination spanner
DGIPRO-502-BAR
Accessories
Part No
PROC-120-C1-K
PROC-120-C2-K
PROC-120-C3-K
PROC-220-**-K
JGAPRO-330-K
PROC-230-**-K
PRO-305-085-10-K
PRO-305-12-14-K
PRO-415-1
SPN-8-K2
SN-406
DGIPRO-502-BAR
MPV-60-K3
HAF-507-K12
4900-5-1-K3
KR-484-K10
** = Fluid nozzle size
24
Description
C1 Air Cap and retaining ring
C2 Air Cap and retaining ring
C3 Air Cap and retaining ring
Suction Fluid Nozzle Size Numbers 16 or 18
Suction Fluid Needle for 14, 16 or 18 Fluid Nozzles
Pressure Fluid Nozzle Size Numbers 085, 10, 12 or 14
Pressure Fluid Needle to match 085 & 10 Nozzle sizes
Pressure Fluid Needle to match 12 & 14 Nozzle sizes
Spray Gun Service/Repair Kit
Torx & flat blade Screwdriver for - Trigger & Needle Packing
Gun wrench, Torx & flat back screwdriver, cleaning brush and colour ID rings
Digital Gauge - Reads in bars
Male Quick Detach Uni Swivel - fits to gun air inlet
Lightweight in-line air filter.
Pack of three cleaning brushes
Pack of 10 suction cup paint strainers
MPV-60-K3
KR-484-K10
PRO-415-1
Catalogue 2012
Ref.
No.
Description
Part No.
Ref.
No.
Description
Part No.
1
Air Cap Retaining Ring
PRO-405-K
16
Air Inlet
SN-40-K
2
Air Cap Retaining Clip
JGA-156-K5
17
Colour ID Ring Kit (4 Colours)
SN-26-K4
3
Aircap & Ring
See page 24
18
Airflow Valve
PRO-411-K
Stud and Screw kit
SN-405-K5
Torx Key
SPN-8-K2
4
Fluid Nozzle
See page 24
19
5
Baffle Plate
SN-41-K
20
6
Spray Head Seal (kit of 2)
SN-18-1-K2
21
Fluid Inlet Connector Kit
PRO-12-K
Cup Lid Assembly
KR-4001-B
Lid Gaskets - kit of 3
KR-11-K3
7
Spray Head & Seal Kit
SN-17-1-K
22
8
Body Bushing & Seal
SN-6-K
23
9
Fluid Needle
See page 24
24
Drip Free Diaphragms - Kit of 5
KR-115-K5
10
Fluid Adjusting Knob, Spring & Pad Kit
PRO-3-K
25
Cup Only
KR-466-K
11
Spreader Valve Assembly
PRO-404-K
26
Complete Cup Assembly
KR-566-1-B
Needle spring and pad kit
SN-4-K3
12
Packing, Spring & Packing Nut Kit
SN-404-K
27
13
Air Valve Seal
SN-34-K5
Service Parts
14
Air Valve Assembly
SN-402-K
Spray Gun repair kit
PRO-415-1
SN-21-K
Seal and Pin Kit, kit of 5
GTI-428-K5
15
Trigger, Stud & Screw Kit
Catalogue 2012
25
Pro Clean Gun Wash
Cleaning Machine
Pro Clean is faster, cleaner and more efficient than
conventional gun wash machines.
Pro Clean can be used for waterborne and solvent
applications.
Significantly reduces solvent use and wastage
dramatically reducing gun cleaning costs.
Fresh solvent is used every time ensuring no
contamination and rapid colour changes.
The compact unit can be wall mounted to maximise
floor space in the mix room.
500ml colour coded waterborne and solvent aerosols
are easily clipped in and out of the machine.
One 500 ml can will clean up to 32 spray guns.
Part Number: DEV-FHAZ1006
Specification
Dimensions
H: 900 mm
W: 245 mm
D: 275 mm
Weight
9 kg
Max Air Pressure
8 bar (116 psi)
Min Air Pressure
6 bar (86 psi)
ATEX Safety Approval
CE Ex II 3G c IIA T6
Pro Clean Gun Wash Machine
Part No
Description
DEV-FHAZ1006
Complete Pro Clean unit
DEV-FHFZ1010
Pro Clean Waterborne Aerosol
DEV-FHFZ1011
Pro Clean Solvent Aerosol
SAVE TIME:
Less than a minute for a completely clean spray gun
SAVE COST:
One 500ml can of cleaner will clean up to 32 spray guns
SAVE SPACE:
Can be wall mounted to keep the floor space clear
SAVE WASTE:
Highly efficient, less than 16 ml of cleaning solution to
clean a gun
26
Catalogue 2012
Remove the paint cup and
connect the gun to the
airline.
Place the gun into the air cap
receiver and trigger for 3-4
seconds.
One press of the cleaning
solution is pumped through
the spray gun cup adaptor.
…and the gun triggered to
clear all the fluid passages of
any paint residue. Repeat.
Press the air button to blow
dry the fluid passages.
Lower the aerosol down to its
bottom position…
…to clean air cap.
Wipe the air cap with a clean
cloth and the gun is ready
for use.
Efficient
Pro CLEAN is compact, can be wall mounted to maximise floor space in the mixing room and can be used
for solvent borne and waterborne materials. The aerosol cleaning solutions for solvent (colour coded
orange) and waterborne (colour coded blue) are simply placed in the machine and one 500 ml can will clean
up to 32 spray guns.
Economical
Research has shown that on average Pro CLEAN significantly reduces gun cleaning costs. Pro CLEAN
doesn’t need regular bulk solvent replacement and recycling as it uses a fraction of the solvent used by
conventional machines.
Ecological
Pro CLEAN uses very small amounts of solvent, significantly reducing waste. There is no splashing and
solvent vapour is virtually eliminated. Nevertheless, the machine has extraction options on both sides of the
unit.
Catalogue 2012
27
DMG Air Dryer Guns
and Systems
A versatile system to speed up the drying process.
DMG guns multiply their intake by a factor of 7 to give
generous air volumes.
A fully adjustable aerodry stand provides full dryer flexibility.
Solvent resistant for cleaning in gun wash machines.
DMG guns feature intake debris filters and shut-off valves.
Specification
Air consumption per gun @3.4 bar (50psi)
325 l/min (11.5cfm)
Recommended working pressure range
2-4 bar (30 – 60 psi)
Noise level at 3.4 bar (50psi)
83 dba
DMG Air Dryer Systems
Part No
Description
DMG-501-K
Single Air Dryer gun – boxed
DMG-620
Two gun stand system with hose
Accessories
28
Part No
Description
DMG-5-K3
Pack of 3 dryer inlet filters
DMG-520-K
Air dryer stand and hose
H-6086-B
10m Air hose with female quick detach and swivel/loose nut
fittings
MPV-424
Female, self sealing, QD air line fitting
MPV-5
Male stem, QD air line fitting with 1/4” BSP(F)
Ref No
Description
Part Number
1
Single Air Dryer Gun
DMG-501-K
2
Female QD
MPV-424
3
Filter pack of 3
DMG-5-K3
Catalogue 2012
DGIPRO-503-BAR-K
(For GTi Pro)
Perfectly positioned for easy checking.
Accurate digital “bar” read-out of working pressure.
Retrofits to GTi Pro or PRi Pro gravity guns.
Optimise your gun performance as you work.
Accurate readings to within 0.05 bar (0.7 psi).
Fully ATEX Approved – totally gun washer safe.
Air flow “cheater” valve adjusts the gauge.
Fitted in minutes - replaces standard spreader valve.
2-3 year battery life – factory replacement service.
DGIPRO-504-BAR-K
(For GTi Pro LITE)
Available Spring 2012
Digital air pressure gauge and control valve.
Resolution steps in increments of
0.05 bar.
Ultra smooth action control valve.
Fits directly to gun air inlet.
1/4“ Universal threads – swivel nut
at outlet.
Fully ATEX Approved – totally gun
washer safe.
Fits in line or directly onto tools and
supply lines.
Very tough to withstand bodyshop duty.
Lasts many times longer than
analogue dial units.
DGIPRO-502-BAR
Specification
Air Connections (m & f)
Accuracy
Part numbers
1/4” Universal (BSP/NPS)
+ or – 1%
DGIPRO-503-BAR-K
DGi PRO pod gauge - Retrofit to GTI Pro guns only
DGIPRO-504-BAR-K
DGi PRO pod gauge - Retrofit to GTI Pro LITE guns
only - available Spring 2012
DGIPRO-502-BAR
DGI Pro Air inlet gauge & adjusting valve
Resolution steps
0.05 bar (0.7 psi)
Max static inlet pressure
12 bar (175 psi)
Housing
Die cast aluminium, nickel/chrome
plated.
Spare parts:
DGI Pro adjusting valve seals
SN-52-K5
Readout window
Toughened glass
Male quick detach swivel
MPV-60-K3
ATEX safety approval
CE Ex 11 1G EEx ia IIC T4
Air inlet aperture inserts
SN-57-K5
Catalogue 2012
29
THE NEW GENERATION IN
DISPOSABLE PAINT CUP SYSTEMS
The DeVilbiss DeKups disposable cup system is the
quick, easy and secure way to spray.
The lightweight cup liner collapses easily providing a
constant paint flow and minimal paint wastage which is
better for your bodyshop and the environment.
l Stable and positive cup to gun location.
l Consistent paint flow, reduced risk of spray
performance changes.
l Practical 710cc size gives ideal weight to quantity ratio.
l Choice of disc filters for waterborne basecoats or washable stick
filters for clears and primers.
l Supplied in convenient wall mounting dispenser packs.
l Lightweight gun adaptor with spiral lock mechanism.
l No threads on outer cup lids to get contaminated and stubborn.
l Storage plugs for liners supplied in the kit.
l Funnels for liner top ups and gun flushing bottles available.
Ready to use, dispenser wall pack complete with 50 disposable
lids and liners. Constant paint flow for accurate colour matching.
Spray at any angle even upside-down.
DPC-611-K2
DPC-602
DPC-610-K50
DPC-607
Part No
Description
DPC-610-K50
DeKups disposable cup system kit – 50 liners, 50 lids, 20 disc filters, 10 stick filters and 10 plugs
DPC-611-K2
Reusable lid and sleeve kit
DPC-602
9oz. disposable lids & liners
DPC-607
9oz. re-usable lid & sleeve kit
30
Catalogue 2012
DPC-10
DPC-11
DPC-13
DPC-52-K1
DPC-78
DPC-80
DPC-23
DPC-501
DPC-42-K20
DPC-6-K10
DPC-27-K10
DPC-22-K3
DPC-8-K2
DPC-62-K10/DPC-63-K10
& DPC-60-K10
Part No
Description
Part No
Description
DPC-10
Adapter for SATA NR 2/3000, RP, KLC, MCB &
Jet 90 series & Sata 96719
DPC-6-K10
Plug Kit (Pack Of 10)
DPC-22-K3
Disposable funnel
DPC-8-K2
Cleaning Bottle
DPC-60-K10
9oz. Measuring Guide (10 Pack)
DPC-62-K10
Measuring guide 2:1 & 3:1
DPC-63-K10
Measuring guide 4:1 & 5:1
DPC-DISP
Dispenser for disposable liners and lids
DPC-TRAN
Disposable Transit Kit
DPC-11
DPC-13
DPC-23
DPC-52-K1
DPC-78
DPC-80
Adapter for SATA NR95, Iwata LPH-400 &
W400LV
Adaptor for Sagola (DeKup)
DPC-501
DPC-42-K20
DPC-27-K10
Adaptor 9oz – for SRI PRO
Adaptor for SATA Minijet QCC
Adaptor For Iwata Supernova
Adapter for DeVilbiss GTi, PRI, GFG, Binks M1G,
Sharpe Cobalt, Platinum & Titanium
Adapter for SATA QC
Disc Filet Kit – 125 micron filter screen
Stick Filter – 200 Micron filter screen
DPC-65-K24
9oz 125micron Disc Filter (24 Pack)
GTIDK-T110B-13
Burgundy GTi Pro fitted with T110 Cap, Size 13
tip & “BASE” laser markings plus DeKup Sampler.
GTIDK-T110B-D-13 Burgundy GTi Pro fitted with T110 Cap, Size 13
tip, a DIGITAL Pro Pod Gauge & “Base” laser
marking plus DeKup Sampler
GTi Pro DIGITAL Kits with DeKups Starter Kit
A Refinisher GTI Pro Gravity kit or GTi Pro Digital Gravity kit is available to enable
you to trial the DeKups system. The following components are included:
1
3
1
1
1
1
x
x
x
x
x
x
DPC 80 Gun Adaptor
3 x DPC-2 Disposable Lids
DPC-18 Disposable Liner
1 x DPC-4 Reusable Lid
DPC56 Reusable Liner
1 x DPC-27 Stick Filter
DPC-42 Disc Filter - Waterbase
DPC-6 Storage Plug
SB-E-4-280 DeKup Instruction Leaflet
Please note that the adaptor will be fitted and tightened into the gun body so it is
ready for immediate use.
Catalogue 2012
31
Gun supply hose swivels both radially and laterally, ensuring
better spray dynamics without the hose restricting the sprayers
movement.
Left or right sided waist belt fitment without having to change
the air fitting configuration.
The Pro Visor disperses breathing air gently around the
lightweight visor at a positive pressure with no misting or
discomfort, ensuring every sprayer can work at their best.
The wrap around visor provides excellent and much wider
peripheral vision than sprayers will be used to, while the
removable peak can help reduce glare from spray booth
lighting.
Specification
Protection:
Carbon Filter Life:
Supply Pressure:
Air Flow Rate:
Noise level @ 160 l/min:
Approvals:
Zone Classifications:
APF = 40 / NPF = 200
3 months
4.0 bar (60 psi) minimum to 7.0 bar (100 psi) maximum
128 – 160 l/min (4.5 – 5.7 SCFM)
69.7 db
PPE directive 89/686/EEC. Conforms to EN 14594:2005 Class 3A
Suitable for use in Zones 1 and 2 Hazardous Areas (gas groups IIA and IIB)
Pro Visor Outfit
PROV-600
Complete air fed visor outfit with waistbelt
MPV-463
Accessories
32
Part No
Description
PROV-20-K
Belt & regulator
PROV-21-K
Peak
PROV-22-K10
Peel off visors pack of 10
PROV-22-K50
Peel off visors pack of 50
PROV-23-K
Belt and buckle
PROV-25-K
Acetate visor face seal and air tube
PROV-26-K
Storage bag
PROV-27-K4
Filter element (pk 4)
PROV-28-K4
Comfort brow band (pk 4)
PROV-29-K
Visor head piece & breathing tube
PROV-30-K
Spacers & knobs (16 items - 1 set)
PROV-31-K
Filter cap & seal
PROV-32-K
Y-piece assembly
PROV-33-K
QD connector with reducer
PROV-406-K
Gun hose (1.2 m)
H-6085-QD
10 metre length air-hose complete with male and female QD’s
H-6065-B
10 metre length air hose complete with re-usable fittings.
MPV-424
Female self-sealing, QD air line fitting
MPV-10
Male-stem, QD air line fitting with ¼” BSP(M)
MPV-5
Male-stem, QD air line fitting with ¼” BSP(F)
MPV- 462
Female self-sealing QD fitting (2 male and 2 females)
MPV-463
Kit of 4 QD fittings for wasitbelt to mask/visor
PROV-21-K
PROV-27-K4
PROV-22-K10
MPV-60-K3
Catalogue 2012
Ref
No
Description
Part Number
1
Pro-Visor complete unit
PROV-600
Ref
No
Description
Part Number
2
Belt & Regulator
PROV-20-K
11
Comfort brow band (Pack 4)
PROV-28-K4
3
Peak
PROV-21-K
12
10m Air hose - 5/16”ID male & female QD’s
H-6085-QD
4
Tear-off visors pack of 10
PROV-22-K10
13
Tear-off visors pack of 50
PROV-22-K50
10m Air hose - 5/16”ID, ¼” BSP G swivel F
connectors
H-6065-B
5
6
Belt and buckle
PROV-23-K
14
Visor head piece & breathing air tube
PROV-29-K
Spacer, stud & knob (set of all sizes)
PROV-30-K
7
1.2m Hose (To Spray Gun)
PROV-406-K
15
8
Rigid acetate visor face seal and air tube
PROV-25-K
16
Filter cap & seal
PROV-31-K
Y-Piece Assembly
PROV-32-K
Connector
PROV-33-K
9
Storage bag
PROV-26-K
17
10
Filter element (Pack 4)
PROV-27-K4
18
Catalogue 2012
33
Complete Air-Fed Half-Mask Outfit
A single airline supplies breathing and spraying air.
One piece high specification goggles are included.
The facepiece incorporates dual exhalation valves
and an air inlet diffuser.
Waistbelt incorporates odour filter and pre-set
mask air regulator.
Outfit includes high quality gun hose (1.2m x 8mm
bore).
Specification
Protection
APF=20 ( not suitable for use with Isocyanates)
Carbon Filter Life
1000 hours
Supply Pressure
3.8 bar (55 psi)
- At hose supply connection max 7 bar (100 psi)
MPV-627 Outfit
Part No
Description
MPV-627
Complete air-fed half-mask outfit
Accessories
Part No
Description
MPV-506-2
Complete half-mask with cotton rimlet, hood & air tube
MPV-4006
One piece protective goggles for use with half mask
MPV-486
Half mask rubber facepiece only
MPV-489-K2
Half-mask exhalation valve
MPV-17-K10
Cotton mask-to-face rimlet-kit of 10
MPV-487
Rubber strap harness for half mask
MPV-488
Half-mask clear air tube assembly with mini QD fitting
H-6085-QD
10 metre length air hose complete with male and female QD’s
H-6065-B
10 metre length air hose complete with re-usable fittings
MPV-518
Complete waistbelt with regulator, filter cartridges & QD’s
MPV-22
Replaceable waistbelt filter cartridge
MPV-455
Waistbelt regulator (does not include belt or QD)
MPV- 519
Waistbelt filter housing
MPV-2-K5
Disposable elasticated ‘Tyvek’ protective hood – kit of 5
MPV-456
Rubber spray gun hose (4’ long, 5/16” bore with QD fittings)
MPV-458
Stowage bag for masks or visors
MPV-424
Female, self sealing, QD air line fitting
MPV-10
Male stem, QD air line fitting with 1/4” BSP(M)
MPV-5
Male stem, QD air line fitting with 1/4” BSP(F)
MPV-462
Female self sealing QD fitting with 1/4” BSP (F)
MPV-463
Kit of 4 QD’s fittings (2 male a 2 females)
MPV-442
Female miniature QD fittings for waistbelt to mask / visor
MPV-20
Male miniature QD stem for waistbelt to mask / visor
MPV-4006
MPV-22
MPV-463
MPV-60-K3
H-6085-QD
34
Catalogue 2012
Ref
No
Description
Part No.
Ref
No
Description
Part No.
1
Mask Assembly (ref nos 2-8)
MPV-506-2
13
Quick detachable stem
MPV-10
2
Facepiece
MPV-486
14
Quick detachable connector
MPV-424
15
3
Exhalation Valve (kit of 2)
MPV-489-K2
4
Kit of 10 cotton rimlets
MPV-17-K10
5
Harness
MPV-487
16
10m length M-F QD Fittings #
H-6085-QD
10m length 1/4” Re-usable Fittings #
H-6065-B
Gun hose assembly
MPV-456
6
Hoods (kit of 5 )
MPV-2-K5
17
Quick detachable stem
MPV-5
7
Tube and mask diffuser assy
MPV-488
18
Stowage bag
MPV-458
8
Quick detachable stem
MPV-20
19
Goggle
MPV-4006
9
Quick detachable connector
MPV-442
19a
Goggle protection strip (kit of 10)
MPV-59-K10
10
Regulator and housing
MPV-455
20
Waistbelt assembly
MPV-518
# Not part of outfit, order separately
11
Disposable filter
MPV-22
12
Waistbelt & filter housing
MPV-519
Catalogue 2012
35
“Valuair” Half-Mask Respirator
Lightweight, soft, pliable facepiece.
“Freedom” Half-Mask Respirator
Easy bayonet fitting filter cartridges.
Lightweight, dual filter, semi-disposable half
mask respirator.
Comfortable elasticated / moulded headstrap
cradle.
Can be used up to a maximum of 28 days.
Maintenance free and requires no spare parts.
Replaceable A2 specification cartridges
supplied as standard.
Low nose bridge helps to accommodate
goggles for optimum vision.
Pre filters to extend the service life of the main
filter cartridges.
Headstrap has no buckles or fasteners and is
comfortable and easy to use.
Specification – A2 Filters
Specification – A2 Filters
A2 filters are for use against organic vapours with boiling points
above 650°C.
A2 filters are for use against organic vapours with boiling points
above 650°C.
The Valuair mask with A2 filter cartridges can therefore be used
in areas of contamination up to 10 x the Occupational Exposure
levels set by the Health and Safety Executive.
The Freedom mask with A2 filter cartridges can therefore be used
in areas of contamination up to 10 x the Occupational Exposure
levels set by the Health and Safety Executive.
Suitable for use with cellulose paints, primers, lacquers and
varnishes but not suitable for use with Isocyanates.
Suitable for use with cellulose paints, primers, lacquers and
varnishes but not suitable for use with Isocyanates.
Assigned Protection Factor of 10.
Assigned Protection Factor of 10.
Part No
Description
Part No
Description
MPV-629
Valuair Cartridge Mask complete with A2
Filter cartridges and pre-filters
MPV-496
Freedom Cartridge Mask complete with A2
Filter cartridges
MPV-492
Pair of pre-filter covers plus ten filter pads
MPV-4006
MPV-494-K2
Pack of two A2 specification filter cartridges
One piece protective goggles for use with
half masks
MPV-4006
One piece protective goggles for use with
half masks
36
Catalogue 2012
DVFR-1 Filter Regulator
Rolling diaphragm gives rapid response and
sensitive air pressure control.
Provides air filtered to 5 microns.
Maximum airflow 3500 l/min (124 cfm).
Suitable for use in booth/oven up to 100°C (212°F).
Three ball valve controlled outlets.
Tamperproof, removable and lockable air pressure
control knobs.
Specification
Air Inlet Thread
1/2” BSP (F)
Regulated Outlets
3 Valved
Unregulated Outlets
NA
Air Outlets (Ball Valves)
1/ 4” BSP (M)
Width (Overall)
175mm (6.9”)
Height (Overall)
280mm (11”)
Weight
2500 gms (88oz)
Capacity (maximum air flow)
3500 l/min (124cfm)
Maximum Air Inlet Pressure
13 bar (189 psi)
Maximum Regulated Outlet Pressure
0-8 bar (0-116psi)
Maximum Operating Temperature
100°C (212°F)
Pressure Gauge
0-11 bar (0-160 psi)
Gauge port
1/8” BSP (F)
Air Filtration
Down to 5 microns
Drain Valve
Semi-Automatic
Maximum Pressure Drop
5% of Inlet Pressure
DVFR-1 Regulator
Part No
Description
DVFR-1
3 Outlet Filter Regulator (90 cfm)
DV-9451705
Replacement 5 micron filter element for DVFR-1
DV-9420601
Filter bowl removal tool
Ref No
Description
Part Number
1
Upper Cover Assembly
DV-9450806
2
Filter (Air)
DV-9451705
3
Metal Filter Bowl
DV-9453301-MET
4
Ball Valve
SER-3414-MF
5
Pressure Gauge
GA-319
6
Isolation Valve
DV-8000035
Catalogue 2012
DV-9451705
DV-9420601
37
DVFR-2 Filter Regulator
COALESCER
High air flows for conventional and compliant
spray guns.
Provides air filtered to 0.01 microns suitable for air-fed
respiratory outfits.
Maximum airflow of 3500 l/min (124cfm).
Suitable for use in booth/oven up to 100°C (212°F).
Three ball valve controlled outlets.
Rolling diaphragm gives rapid response and sensitive air
pressure control.
Specification
Air Inlet Thread
1/2” BSP (F)
Regulated Outlets
3 Valved
Unregulated Outlets
NA
Air Outlets (Ball Valves)
1/ 4” BSP (M)
Width (Overall)
240mm (9.5”)
Height (Overall)
280mm (11”)
Weight
3200 gms (113oz)
Capacity (maximum air flow)
3500 l/min (124cfm)
Maximum Air Inlet Pressure
13 bar (189 psi)
Maximum Regulated Outlet Pressure
0-8 bar (0-116psi)
Maximum Operating Temperature
100°C (212°F)
Pressure Gauge
0-11 bar (0-160 psi)
Gauge port
1/8” BSP (F)
Air Filtration
Down to 0.01 microns *
Drain Valve
Semi-Automatic
Maximum Pressure Drop
10% of Inlet Pressure
* Suitable for Breathing Air
DVFR-2 Regulator
38
Part No
Description
DVFR-2
3 Outlet Filter Regulator Coalescer (50 cfm)
DV-9451705
Replacement 5 micron filter element for DVFR-2
DV-9451711
Replacement 0.01 micron fine filter breathing air element for DVFR-2
DV-9420601
Filter bowl removal tool
Ref No
Description
Part Number
1
Upper Cover Assembly
DV-9450806
2
Filter (Air)
DV-9451705
3
Metal Filter Bowl
DV-9453301-MET
4
Ball Valve
SER-3414-MF
5
Pressure Gauge
GA-319
6
Fine Filter (Oil)
DV-9451711
7
Isolation Valve
DV-8000035
DV-9451705
& DV-9451711
DV-9420601
Catalogue 2012
DVFR-3 Filter Regulator
Dual filtration process provides air filtered to 20 microns.
Maximum airflow of 1700 l/min (60cfm).
Two ball valve controlled outlets.
Ideal for general workshop or prep deck duty.
Semi automatic filter drain.
Specification
Air Inlet Thread
1/2” BSP (F)
Regulated Outlets
2 Valved
Unregulated Outlets
NA
Air Outlets (Ball Valves)
1/ 4” BSP (M)
Width (Overall)
165mm (6.5”)
Height (Overall)
240mm (9.5”)
Weight
1341 gms (46oz)
Capacity (maximum air flow)
1700 l/min (60cfm)
Maximum Air Inlet Pressure
13 bar (189 psi)
Maximum Regulated Outlet Pressure
0-8 bar (0-116psi)
Maximum Operating Temperature
40°C (104°F)
Pressure Gauge
0-11 bar (0-160 psi)
Gauge port
1/8” BSP (F)
Air Filtration
Down to 20 microns
Drain Valve
Semi-Automatic
Maximum Pressure Drop
5% of Inlet Pressure
DVFR-3 Regulator
Part No
Description
DVFR-3
2 Outlet Filter Regulator (60 cfm)
9351706
Replacement 20 micron filter element for DVFR-3
Ref No
Description
Part Number
1
Upper Cover Assembly
DV-9350811
2
Filter
9351706
3
Metal Filter Bowl
DV-9353301
4
Ball Valve
SER-3414-MF
5
Pressure Gauge
GA-319
9351706
GA-319
Catalogue 2012
39
DVFR- 8 Filter Regulator
Coalescer with Activated Carbon Filter
High air flows for conventional and compliant spray guns.
Provides air filtered to 0.01 microns suitable for air-fed
respiratory outfits.
Activated carbon filter removes oil carry over to 0.003 ppm.
Maximum airflow of 3500 l/min (124cfm).
Suitable for use in booth/oven up to 100°C (212°F).
Three ball valve controlled outlets.
Rolling diaphragm gives rapid response and sensitive air
pressure control.
Specification
Air Inlet Thread
1/2” BSP (F)
Regulated Outlets
3 Valved
Unregulated Outlets
NA
Air Outlets (Ball Valves)
1/ 4” BSP (M)
Width (Overall)
305mm (12”)
Height (Overall)
280mm (11”)
Weight
3.3kg
Capacity (maximum air flow)
3500 l/min (124cfm)
Maximum Air Inlet Pressure
13 bar (189 psi)
Maximum Regulated Outlet Pressure
0-8 bar (0-116psi)
Maximum Operating Temperature
100°C (212°F)
Pressure Gauge
0-11 bar (0-160 psi)
Gauge port
1/8” BSP (F)
Air Filtration
Down to 0.01 microns *
Drain Valve
Semi-Automatic
Maximum Pressure Drop
10% of Inlet Pressure
* Suitable for Breathing Air
DVFR-8 Regulator
40
Part No
Description
DVFR-8
3 Outlet Filter Regulator Coalescer with activated carbon filter
DV-9451705
Replacement 5 micron filter element for DVFR-8
DV-9451711
Replacement 0.01 micron fine filter breathing air element for DVFR-8
DV-9451711-AC
Replacement 0.003 ppm activated carbon filter element for DVFR-8
DV-9420601
Filter bowl removal tool
Ref No
Description
Part Number
1
Upper Cover Assembly
DV-9450806
2
Filter (Air)
DV-9451705
3
Metal Filter Bowl
DV-9453301-MET
4
Ball Valve
SER-3414-MF
5
Pressure Gauge
GA-319
6
Fine Filter (Oil)
DV-9451711
7
Isolation Valve
DV-8000035
8
Activated Carbon Filter
DV-9451711-AC
DV-9451705
& DV-9451711
DV-9451711AC
Catalogue 2012
Economy Filter Regulators and Coalescers
FLFR-1 Filter Regulator
Air filtration down to 20 microns.
High quality manufacture.
Air flow of 70cfm (at 7 bar – 100psi inlet pressure).
Lockable and removable (tamperproof) control.
FLCF-1 Coalescing Filter
A 3/8” (port size) coalescing (fine oil) filter.
Air filtration down to 0.01 microns (suitable for
breathing air-fed visors/masks).
Replaceable filter element.
Maximum working pressure 18 bar (260 psi).
FLFR-1
FLCF-1
FLRC-1 – Filter Regulator Coaslescer
Compact, low cost single operator Filter Regulator and Coalescer.
Filtration down to 0.01 microns suitable for air mask or visor.
Not suitable for low bake temperatures.
FLRCAC-1
FLRCAC-1
FLRC-1
FLRCAC-1 Filter Regulator Coalescer with Activated
Carbon Filter
High efficiency filter designed to remove dirt, liquid oil
and water from spraying and breathing air.
Filtration down to 0.01 microns plus activated carbon filter
removing contaminants down to 0.003ppm.
Regulator Assemblies
Part No.
Description
Part No.
Description
FLFR-1
Single outlet Filter Regulator (70cfm)
XA-12
Replacement coalescing filter element
FLCF-1
Coalescing (fine oil) filter (25cfm)
AC-12
Replacement activated carbon filter
FLRC-1
Single outlet Filter Regulator Coalescer
9450802
Upper Cover
Single outlet filter regulator coalescer with activated
carbon filter
9450301
Metal Bowl
GA-319
Gauge
9450102
Replacement filter element
FLRCAC-1
Catalogue 2012
41
Gravity and Suction Cup Accessories
Gravity Feed Cups
Part No
Description
GFC-501
568ml (1 Pint) Acetal gravity cup for GTI / GFG
KGP-509-1
284ml (1/2 Pint) Nylon gravity cup for GFG
SRi-510
125ml Acetal gravity cup
SRi-42-K3
Pack of 3 cone filters
SRi-478-K12
Pack of 12, 125ml gravity cups for SRi
SRi-480-K3
Black cup and lid for UV paint
GFC-402
Lid assembly for GFC-501 gravity cup
KGP-401
Lid assembly for KGP-509 gravity cup
GFC-17-K5
Washer
GFC-2-K5
Pack of 5 drip check lids
KGP-5-K5
Pack of 5 gravity cup strainers for GFC-501 &
KGP-509
SRi-8-K6
Pack of 6 lids for SRi gravity cups
42
Suction Feed Cups
Part No
Description
KR-566-1-B
1 litre standard suction cup and lid assembly for JGA
KR-466-K
Cup only – 1 litre suction cup
KR-4001-B
Suction cup lid assembly for JGA cups
KR-115-K5
Pack of 5 drip free diaphragms
KR-11-K3
Pack of 3 Tri-Seal gaskets for KR suction cups
KR-69-K3
Pack of 3 Leather gaskets for suction cups
KR-483-K10
Kit of 10 mesh KR cup strainers – to fit 7/16” tube,
115 Micron
KR-484-K10
Kit of 10 mesh KR cup strainers – to fit 7/16” tube,
350 Micron
KR-110-K3
Kit of 3 Spot Pots
Catalogue 2012
In-Line Air Filters
l Lighweight, gun mounting air filter
l High efficiency action traps water, oil and dirt
l Tough solvent resistant Delrin® housing with 1/4” threads
Part No: HAF-507-K12
In-Line Air Adjusting Valve
l Fits neatly in-line at the gun air inlet
l Increase or decrease working pressure at the gun
l Calibrated up to 11 Bar (160 psi)
Part No: HAV-501-B
Gun Cleaning Brushes
l Ideal for a variety of gun cleaning jobs
l Tough resilient bristles for useful service
l Suitable size for cleaning most parts of the gun
Part No: 4900-5-1-K3 Pack of 3 brushes
Duster/Blow Guns
l Palm size trigger operated with diffused air flow
l Low noise factor
l Durable design
Part No: DGD-505-E
Viscosity Cups
l The fast, simple way to check out paint viscosity
l Tough durable and easy to clean
l Precision metal drain out insert
Part No: 7000-114-K2 Pack of 2 viscosity cups
Mixing Cups
l Easy to use, disposable mixing cups
l Made from solvent resistant clear polypropylene
l Calibrated with a 0-600 volumetric measurement scale
Part No: MC-1-K50 Pack of 50 cups
Trigger Clip
l Made for solvent resistant acetal
l Locks trigger in open position for gun wash machine
l Snaps in place for secure fit
Part No: PRO-15-K3
Professional Spray Gun Cleaning Kit
l Handy tool wrap style kit of purpose made cleaning brushes and tools
l Includes cleaning instructions and spray gun oil
l Keeps your spray guns in top working order
Part No: KK-4584
Spray Gun Service Kit
l Spray gun service/repair kit for GTIPRO and SRIPRO
Part Nos: PRO-415-1 – Service kit
Catalogue 2012
43
DGi PRO Digital Gauge
l The most accurate digital gauge available
l Clear and easy to read, just squeeze the trigger to set
l Smooth, accurate control even when wearing gloves
Part No: DGIPRO-502-BAR
DGi PRO pod
l Perfectly positioned for easy checking
l Accurate digital “bar” read-out of working pressure
l Accurate readings to within 0.05 bar (0.7 psi)
Part No: DGIPRO-503-BAR-K (GTi Pro)
Part No: DGIPRO-504-BAR-K (GTi Pro LITE) - available Spring 2012
Gravity Gun Stands
l Stable metal workbench gun stands
l Choice of 2 stands for 3 gravity guns or a single gun
l Single gun stand is ideal for SRi guns and full size guns
Part Nos: GGS-1 – 3 gun stand
GFV-50F – single gun stand
Gravity Cup Filters
l Effectively removes dirt, flakes and scum
l Keeps the finish blemish free
l Resistant to most solvents – easily cleaned
Part No: KGP-5-K5 - Pack of five filters
Suction Cup Filters
l Convenient, easy fit suction cup paint filters
l Keeps spray gun passages clear
l Removes dirt, flakes and scum
Part Nos: KR-484-K10
51 mesh filter screen (general purpose)
130 mesh filter screen (finer filtration)
KR-483-K10
Suction Cup Lid Gaskets
l Ready to use, purpose fit suction cup lid seals
l Choose between Tri-Seal or traditional leather gaskets
l Fits all DeVilbiss KR type suction cups
Part Nos: KR-11-K3 Tri-seal gaskets
KR-69-K3 Leather gaskets
Drip-Free Diaphragms
l Prevents suction cup leaks and vent hole blockages
l Allows the cup to be used at angles
l Fits snugly under the cup lid
Part No: KR-115-K5 (Pack of 5)
Spot Pots
l 0.5 litre capacity nylon cup insert cuts down on costly paint mixes
l Tapered base ensures that minimal quantities of paint can be utilised
l Quickly and easily cleaned for frequent colour changes
l Fits all 1 litre capacity KR type suction cups
Part No: KR-110-K3
44
Catalogue 2012
Hose & Fittings
l High Flow Air Hose with Connections
l High air flow, high quality rubber air hose
l 8mm (5/16”) bore ideal for use with conventional, compliant / HVLP spray guns, air fed breathing
equipment and other air tools.
Option 1
Option 2
10 metre length air hose complete with quality
10 metre length air hose complete with
chrome replaceable 1/4” swivel nut female
crimped female quick detach connection at
fittings either end.
one end and crimped male QD fitting at the
Part No: H-6065-B
other end.
Part No: H-6085-QD
Option 3
10 metre length air hose complete with crimped
female quick detach connection at one end and
crimped female loose nut fitting at the other
end.
Part No: H-6086-B
l High Flow Air Hose (by the metre) and connections
Option 1
Option 2
Air Hose Part No: H-7501
Air Hose Part No: H-7502
- 8mm (5/16”) bore red rubber air hose
- 9.5mm (3/8”) bore red rubber air hose
Connection Part No: PA-HC-4527
Connection Part No: PA-HC-4528
- 1/4” BSP Female (8mm (5/16”) hose bore)
- 1/4” BSP Female (9.5mm (3/8”) hose bore)
l Fluid Hose (by the metre) and connections
Option 1
Option 2
Fluid Hose Part No: H-7503
Fluid Hose Part No: H-7504
6mm (1/4”) bore black rubber fluid hose
9.5mm (3/8”) bore black rubber fluid hose
Connection Part No: PA-HC-4543
Connection Part No: PA-HC-4548
3/8” BSP Female (6mm (1/4”) hose bore)
3/8” BSP Female (9.5mm (3/8”) hose bore)
Quick detach fittings
l High flow connections – minimal pressure drops
l Ideal for spray guns, respirators, hoses and regulators
MPV-5 – Male quick detach stem with 1/4” female fitting: MPV-424 – Female quick detach connection with 1/4” male fitting: MPV-10 – Male quick detach stem with 1/4” male fitting: MPV-462 – Female quick detach with 1/4” female fitting: MPV-463 – Economy pack, includes 1 of each shown above: MPV-60-K3 – Male quick detach Uni Swivel stem with 1/4” female fitting: Catalogue 2012
45
KBII 2.3 LITRE
REMOTE CUP
2.3 litre capacity –
greater area coverage,
less refills.
Aluminium or stainless
steel options (for waterbase
materials).
Familiar gun grip handle
plus belt hook for operator
convenience.
At-the-job controls with lid
mounted pressure gauge.
Available complete with short cup to gun
air and fluid hoses
KB disposable liners make cleaning and colour changes
fast and simple.
Specification
Air Inlet and outlet connections threads
1/4” BSP (M)
Fluid outlet connection (to spray gun)
3/8” BSP (M)
Maximum working pressure
2.1 Bar (30 psi)
Maximum air supply pressure
8.6 bar (125 psi)
Height
183 mm
Weight (less hoses)
1.76 kg
Cup Capacity
2.3 litres
Spray Gun Kits for use with KBII
Part No
Description
GTIPPRO-**-***
Pressure Feed Gun with either H1, T1, T2, T3 or T4 air cap and either 085, 10, 12, 14,
16, 18 or 20 fluid nozzle
PROPL -**-***
GTi Pro LITE Pressure Feed Gun with either TE10, TE20, TE30 or TE40 air cap and either
085, 10, 12 or 14 fluid nozzle
JGAPPRO-**-***
Pressure Feed Gun with either C1, C2 or C3 air cap and either 085 12, 14, 16 or 18
fluid nozzle
Kit contents are spray gun, (suction cup with filter if appropriate), Torx key, brush and multi-fit spanner
** = Air Cap / *** = Fluid Tip
KBII Remote Cup kits
Part No
Description
KB-522
Aluminium Remote Cup without hoses
KB-522-SS
Stainless Steel Remote Cup without hoses
KB-622
Aluminium Remote Cup complete with air and fluid hoses
KK-5051
Accessories
46
Part No
Description
KB-422
Aluminium 2.3 Litre KBII Spare Cup Only for KB-522
KB-442
Stainless Steel 2.3 Litre KBII Spare Cup Only for KB-522-SS
KK-5051
Kit of 20 disposable liners plus lid diaphragms
H-6066-B
1.2m Air Hose Assembly with BSP Fittings
H-6067-B
1.5m Fluid Hose Assembly with BSP Fittings
KB-422
Catalogue 2012
Ref
No
Description
Part Number
Ref
No
Description
Part Number
1
Retaining Ring
KB-64
15
Regulator Assembly
KB-428-1
2
Slip Rings
KB-81-K5
16
Spring
-
3
Handle
KB-74
17
Valve
-
4
CD Nut
-
18
Valve Seat and Seal
-
5
Connector 1/4” BSP
JGA-158
19
Diaphragm
-
6
Pressure Relief Valve
KB-66
20
Slip Ring
-
7
Lid
Not available
21
Spring
-
8
Gauge
GA-355
22
Bonnet
-
9
Seal
KB-80-K5
23
Seal kit of 6
KB-60-K6
10
Locknut (KB-522) kit of 5
MBD-11-K5
24
Tube Assembly 3/8” BSP(KB-522-B)
KK-4997
-
Locknut -Stainless Steel (KB-522-SS) kit of 2
KB-97-K2
-
Tube Assembly 3/8” BSP STS (KB-522-SSB
KK-4996
Cup – Aluminum (KB-522)
KB-422
25
Check Valve and Seal Assembly
KB-444
Cup – Stainless Steel (KB-522-SS)
KB-442
26
Seal kit of 5
KB-101-K5
12
Check Valve kit of 3
KB-432-K3
Hose & Fittings
13
Seal kit of 5
KB-85-K5
Air hose 5/16" ID. 4ft BSPF
H-6066-B
14
Safety Valve
TIA-4355
Fluid hose 1/4" ID. 4.75ft BSP
H-6067-B
11
Catalogue 2012
47
Binks DVP Double Diaphragm Pump
Choice of pail or wall-mounted outfits.
Rapid delivery of up to 8.5 litres per minute.
Even material flow at up to 60 cycles / minute.
Economic air consumption at pressures up to
7 bar (100psi).
Designed for quick flushing and material
changes.
Specification
Pump Ratio
1:1
Regulated air pressure
7 bar
Max. paint viscosity (ford 4)
60 sec
Universal threaded fluid connector
1/4”
Max. temperature
90°C
Recommended operating speed: Cycle/min
60
Max. fluid pressure
7 bar
Max. fluid flow
8.5 l/min
Universal fluid threaded connector
3/8”
Part No
Description
DVP-610
Compact double diaphragm fluid pump. Complete with “Euro” lid for pail mounting (Pail
not included)
DVP-630
Compact double diaphragm fluid pump for wall mounting. Complete with wall mounting
bracket and suction wand.
H-7501
PA-HC-4527
8mm (5/16”) bore red rubber air hose
1/4” BSP Female (8mm (5/16”) hose bore)
H-7502
PA-HC-4528
9.5mm (3/8”) bore red rubber air hose
1/4” BSP Female (9.5mm (3/8”) hose bore)
H-7503
PA-HC-4543
6mm (1/4”) bore black rubber fluid hose
3/8” BSP Female (6mm (1/4”) hose bore)
H-7504
PA-HC-4548
9.5mm (3/8”) bore black rubber fluid hose
3/8” BSP Female (9.5mm (3/8”) hose bore)
Spray Gun Kits for use with DVP Pump Outfits
Part No
Description
GTIPPRO-**-***
Pressure Feed Gun with either H1, T1, T2, T3 or T4 air cap and either 085, 10, 12,
14, 16, 18 or 20 fluid nozzle
PROPL -**-***
GTi Pro LITE Pressure Feed Gun with either TE10, TE20, TE30 or TE40 air cap and
either 085, 10, 12 or 14 fluid nozzle
JGAPPRO-**-*** Pressure Feed Gun with either C1, C2 or C3 air cap and 085 12, 14, 16 or 18 fluid
nozzle
Hose by the metre
H-7501 &
PA-HC-4527
Kit contents are spray gun, (suction cup with filter if appropriate), Torx key, brush and multi-fit spanner
** = Air Cap / *** = Fluid Tip
Repair Kits
48
Part No
Repair Kit Reference
DVP-114
A
Description
Kit of 6 gaskets
KK-4630
B
Diaphragm and stud kit
KK-4631
C
Standard fluid valve kit
KK-4633
E
Reverse switch kit
KK-4634
F
Pneumatic distributor
Hose by the metre
H-7503 &
PA-HC-4543
Catalogue 2012
Service Kits
Ref No
Description
A
Kit of 6 gaskets
B
Diaphragm and stud kit
C
Standard fluid valve kit
E
Reverse switch kit
F
Pneumatic distributor
Ref No
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
Description
Cap screw
Handle
Cover
Nut
Disc spring
Top plate
Retaining nut
Diaphragm
Pressure plate
Gasket
Bush
O Ring
Stainless Steel valve seat
Teflon ball 16mm
Polyurethane ball 16mm
Stud
Stud
Teflon ball 14mm
Polyurethane ball 14mm
Bush
Body
Swivel elbow
Nylon tube
Manual restart stem
Catalogue 2012
Part Number
SSF-3153-ZN
SSH-460
DVP-22
SSF8151
ZZ-1660D
DVP-131
B
B
B
ABCDE
CD
CD
CD
C
D
B
DVP-75
C
D
CD
DVP-83
SSP-6462
ESTA-433-1
F
Ref No
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
Description
Distributor nut
Bottom plate
Cap screw
Retaining nut
Spring
Reverse valve
O valve seat
Manual restart stem
Air valve piston
Sleeve nut
Cylinder
O Ring
Slide valve
Air muffler
Gauge
Double nipple
Air regulator
Swivel elbow
O ring
Bush
Seal ring
Seal ring
O ring
Snap ring
Part Number
DVP-114
KK-4630
KK-4631
KK-4633
KK-4634
Part Number
F
DVP-130
SSF-3152
E
E
E
E
F
F
F
F
F
F
DVP-17
DVP-31
DVP-20
DVP-30
DVP-35
B
B
F
E
E
F
49
Air Assisted Airless Pump Outfits
Fully stainless steel wetted parts and fluid section.
Magnetic detent (patent) for quick stroke change over with no pulse.
Anti stall no ice design.
Large sight glass for visual packing inspection.
Solvent cup keeps packings well lubricated.
Self adjusting spring loaded packings.
Divorced pump design – zero potential for paint to enter air motor.
Durable design for heavy duty long working life.
CE marked and fully ATEX approved.
Specification
Pump Ratio
32:1
Max. Inlet Pressure
8.0 bar (120 psi)
Flow Rate Nominal
1.5 l/min
Flow Rate Max.
4.0 l/min
Volume/cycle
24 cm3
Max. Operating Pressure
256 (3600 psi)
Cylinder Diameter
85mm
Piston Stroke
75mm
Air consumption at 20 cycles/min
201 l/min
Air Assisted Airless Pump Outfits
Part No
Description
MX-0432W-AAA
Air Assisted Airless High Pressure Pump: 4 l/min – Wall mounted,
complete with high pressure filter and air regulator, twin air and fluid
hose and AAA 4400 spray gun.
MX-0432C-AAA
Air Assisted Airless High Pressure Pump: 4 l/min – Cart mounted,
complete with high pressure filter and air regulator, twin air and fluid
hose and AAA 4400 spray gun.
MX-0432T-AAA
Air Assisted Airless High Pressure Pump: 4 l/min – Tripod mounted,
complete with high pressure filter and air regulator, twin air and fluid
hose and AAA 4400 spray gun.
Accessories
50
Part No
Description
0110-009132
Filter insert for high pressure filter - 100 mesh
0110-009133
Filter insert for high pressure filter - 150 mesh
0110-009134
Filter insert for high pressure filter - 200 mesh
54-5788-K5
AAA 4400 spray gun filter kit of 5 - 60 mesh
54-5789-K5
AAA 4400 spray gun filter kit of 5 - 100 mesh
Catalogue 2012
Ref
No
Description
Part Number
Ref
No
Description
Part Number
1
Gun Body
-
12
54-5788-K5
2
Baffle Plate (Kit of 10)
SPA-71-K10
Fluid Filter 60 Mesh (Kit of 5)
(100 Mesh Filter (Kit of 5) 54-5789-K5)
3
Fluid Seat (4400PSI) (Tungsten Carbide)
54-5779-K
13
Fluid Inlet Swivel (1/4” NPS)
-
3A
Twist Tip Fluid Seat (4400PSI) (Tungsten
Carbide)
54-5832-K
14
Filter Adapter Nut
-
15
Air Inlet Fitting 1/4” NPS (Kit of 3)
SN-9-K3
4
Gasket (Kit of 10)
SPA-98-K10
16
Filter Bracket Screw
-
5
Flat Tip (Fine Finish Tips 9-XXXX-F)
114-XXXXX
17
Filter Bracket
-
5A
Twist Tip
9-XXX-75
18
Fluid Needle Assembly (4400 PSI)
-
5B
Twist Tip Brace (Kit of 2)
54-5801-K2
19
Blanking Needle Nut
54-5850
6
Flat Tip HVLP Air Cap
(Flat Tip Trans-Tech Air Cap 54-5797-K)
54-5795-K
20
Needle Spring Pad
-
6A
Twist Tip HVLP Air Cap
(Flat Tip Trans-Tech Air Cap 54-5798-K)
54-5796-K
21
Needle Spring (4400 PSI)
-
22
Spreader Valve Assembly
54-5815
7
Retaining Ring
54-5852
23
Body Bushing
-
8
Flat Tip Guard
54-5794
24
Body Bushing Gasket
-
8A
Twist Tip Guard
54-5793
25
Trigger Nut
-
9
Air Valve Assembly
SN-402-K
26
Trigger Screw
-
10
Trigger
-
27
Top Filter Seal
-
11
Fluid Tube Assembly
54-5780
28
Bottom Filter Seal
-
Catalogue 2012
51
Binks Pressure Feed Tank
Zinc plated tank shell for long service life.
Single regulator and gauge to control tank and air
pressure.
Zinc plated lid assemblies for solvent based coatings.
Positive 4 point lid clamping for secure operation.
High density polyethylene, tank liners ensure
efficient use.
Specification
Tank Capacity
9.5 litre
Maximum working Pressure
5.5 bar (80psi)
Safety Valve Set Pressure
5.5 bar (80psi)
Air Inlet Size
1/4” BSP (M)
Fluid Outlet Size
3/8” BSP (M)
Tank Shell
SA-620 H.R Steel Zinc plate 2.7mm (8 gauge)
Tank Lid
SA-414 H.R Steel Zinc plate 4.2mm (3/16”)
Fluid Tube
Steel, Galvanised Zinc Plate
Air Manifold
CRS Zinc Plated
Fluid Outlet
Steel, Galvanised Zinc Plate
Lid Gasket
Santoprene
Spray Gun Kits for use with KBII
Part No
Description
GTIPPRO-**-***
Pressure Feed Gun with either H1, T1, T2, T3 or T4 air cap and either 085, 10,
12, 14, 16, 18 or 20 fluid nozzle
PROPL -**-***
GTi Pro LITE Pressure Feed Gun with either TE10, TE20, TE30 or TE40 air cap and
either 085, 10, 12 or 14 fluid nozzle
JGAPPRO-**-*** Pressure Feed Gun with either C1, C2 or C3 air cap and 085 12, 14, 16 or 18
fluid nozzle
PT-78-K10
Kit contents are spray gun, (suction cup with filter if appropriate), Torx key, brush and multi-fit spanner
** = Air Cap / *** = Fluid Tip
Pressure Feed Tank
52
Part No
Description
83C-210-B
9.5 litre capacity zinc plated tank and lid assembly
PT-78-K10
Kit of 10 polyethylene inner liners for 9.5 litre capacity tank
VS-521
Paint filter (100 mesh) and housing – fits directly onto fluid outlet of tank - NPSM
VS-522
Paint filter (100 mesh) and housing – fits directly onto fluid outlet of tank - BSP
H-7501
PA-HC-4527
8mm (5/16”) bore red rubber air hose
1/4” BSP Female (8mm (5/16”) hose bore)
H-7502
PA-HC-4528
9.5mm (3/8”) bore red rubber air hose
1/4” BSP Female (9.5mm (3/8”) hose bore)
H-7503
PA-HC-4543
6mm (1/4”) bore black rubber fluid hose
3/8” BSP Female (6mm (1/4”) hose bore)
H-7504
PA-HC-4548
9.5mm (3/8”) bore black rubber fluid hose
3/8” BSP Female (9.5mm (3/8”) hose bore)
Hose by the metre
H-7501 &
PA-HC-4527
Hose by the metre
H-7503 &
PA-HC-4543
Catalogue 2012
Ref
No
Description
Part
Number
Ref
No
Description
Part
Number
1
Tank Assy. Kit (Includes Ref Nos. 1A, 13, 14,
15 & 16)
-
13
Thumb Screw
-
1A
Tank Shell
-
14
Yoke Assembly
-
2
Lid Gasket, Santoprene
PT-33-1
15
Cotter Pin, 3/32 x 1”
-
3
Lid, Zinc Plated
-
16
Hinge Pin
-
4
Gauge
83-2727
17
Fluid Tube
PT-31
5
Regulator
HAR-511
18
Tank Liner (Kit of 10)
PT-78-K10
6
90° Swivel Adaptor 1/4’ NPS (F) x 1/4’ NPT
(M)
SSP-30-ZN
-
Tank Liner (Kit of 60)
PT-78-K60
19
Hex Nipple 1/4’ NPT (M)
SSP-462-ZN
7
Cross 1/4’ NPT (F)
-
20
Air Relief Valve
SS-2707
8
Safety Valve - 80 psi
TIA-5080-CE
21
D.M Nipple
83-4233
9
Handle
PT-32
22
(NPS) Nipple 1/4 ‘ NPT (M) x 1/4’ NPS (M)
H-2009
10
Hex Nut 3/8’ – 16
-
(BSP) Nipple 1/4 ‘ NPT (M) x 1/4’ BSP (M)
2101004
11
Nipple 3/8’ NPT (M) x 3/8’ NPT (M)
AD-11
NPS) Nipple 3/8‘ NPT (M) x 1/4’ NPS (M)
83-4233
Nipple 3/8’ NPT (M) x 3/8’ BSP (M)
2101007
(BSP) Nipple 3/8‘ NPT (M) x 1/4’ BSP (M)
2101005
Street Elbow 3/8’ NPT (F) x 3/8’ (M) S.S
SSP-1939
12
Catalogue 2012
23
53
Rage Gold - Premium Grade Filler
Formulated with Hattonite for lubricated application and to reduce frictional heat during sanding. Stain
resistant for use with base / clear systems. Available in cartridge form for use with wall mounting dispenser
machine.
Container size: 1.5 Litre tin plus tube of hardener
Part No: FE101668-RG
Cartridge size: 1.6 Litre cartridge plus hardener cartridge
Part No: FE104168-RGDIS
Z-Grip - Non-Clogging Lightweight Filler
Provides superior surface adhesion and corrosion resistance on steel and aluminium. Easy, non-clog sanding.
Available in cartridge form for use with wall mounting dispenser machine.
Container size: 3 litre tin plus tube of hardener
Part No: FE101667-ZG
Cartridge size: 1.6 Litre cartridge plus hardener cartridge
Part No: FE104167-ZGDIS
EuroGold - Premium Lightweight European Style Mastic
A high build lightweight paste which is exceptionally easy to sand. It’s formulated with premium quality,
highly reactive resin for optimum speed and performance. EUROGOLD has excellent adhesion to zinc, steel,
aluminium and many plastics.
Container size: 1.5 litre tin plus tube of hardener
Part No: FE104271
Euro-Sand - Polyester finishing and blending putty
Ideal for filling and skim coating bodywork, pinholes, grind marks, low spots, and other surface imperfections.
Adheres well to steel, galvanized, other zinc coated steel, aluminum, and most rigid to semi-rigid fiberglass and
thermo-set plastics.
Container size: 1.5 litre tin plus tube of hardener
Part No: FE104270
Easy Sand - Pourable blending putty to intermix with Evercoat fillers
Tan coloured flowable polyester glazing putty for filling pinholes and grind marks. Self levels and is ideal for
skim coats. Available in pump action dispenser or 709ml tube.
Container size: 900ml pump action dispenser plus tube of hardener
Part No: FE101669-ES
Polyflex – Polyester Glazing Filler
A flexible polyester filler designed for filling minor imperfections in flexible bumpers and plastic parts prior to
applying spray filler. Approved surfaces: most rigid, semi-rigid and flexible plastics, steel, zinc coated steel and
aluminium.
Container size: 900 ml pump action dispenser plus tube of hardener
Part No: FE104411-PF
440Express
Evercoat 440Express is a liquid application that eliminates micro-pinholes on filled areas that may be
very hard to identify prior to primer application. Testing has shown, when used properly, 440Express will
eliminate up to 90% of all rework caused by micro-pinholes. All it takes is 30 seconds to a better repair.
Container size: 16 fl.oz. (473ml)
Part No: FE104440
Container size: 4 fl.oz. (118ml) with 12 applicators and 2 pads
Part No: FE104444
440 Express Applicators - pack of 12
Part No: FE104439
54
Catalogue 2012
Plastic Repair Adhesive - Medium Set and Fast Set Urethane
A two component urethane repair material that provides incredible strength and stability with a fast cure time.
This urethane material is used for non-structural repairs on fibreglass and automotive plastics.
Cartridge size: 250 ml - Medium Set
Part No: FE104185
Cartridge size: 250 ml - Fast Set
Part No: FE104187
Adhesive Mixing Tips - pack of 12
Part No: FE100817
Metal Bonding Adhesive - Fast Set
A fast setting modified acrylic adhesive for metal to metal surfaces. This adhesive is used for replacing door
skins, roofs, quarter panels, truck bedsides and other non-structural panels. Has excellent adhesion to bare
steel, galvanised steel and e-coated panels.
Cartridge size: 250 ml
Part No: FE104112
Adhesive Mixing Tips - pack of 12
Part No: FE100817
Manual Caulking Gun
Manually operated 26:1 caulking gun to be used with Evercoat’s adhesive products. Part No: FE100830
Hardener
Fast, effective hardener – supplied with above products and also available separately.
Tube size: 28g tube or 78g tube. Part No: FE101474 (28g)
Part No: FE101475 (78g)
Durable Plastic Spreaders
For fast, smooth application of fillers and putties. Flexible, durable and reusable.
Pack of 3 spreaders
Part No: FE100381
Mixing Palette
Made from smooth, durable, heavy duty plastic. Bows for ease of clean up.
12” x 12” mixing area
Catalogue 2012
Part No: FE100155
55
Ref
No
Description
Part No.
Ref
No
Description
Part No.
1
Air Cap/Retaining ring
SP-100-510-K
13
Connector
SP-611-K
2
Nozzle (** = 1.0, 1.4, 1.6, 1.8, 2.0, 2.2mm)
SP-200S-**-K
14
Airflow Valve
SP-402-K
3
Separator
SP-623-K5
15
Fluid Inlet Connector and seal
SP-610–K
4
Packing
GTI-439-K2
16
Air Valve Service Kit
SPK-101-K
5
Spreader Valve
SP-401-K
17
RetainingRing and Seals
SPK-102-K
6
Stud and Screw
GTI-408-K5
18
Spreader/ Cheater Service Kit
GTI-428-K5
7
Needle Adjusting Screw
SP-614-K
19
Circlip
25746-007-K5
8
Spring
SP-622-K5
20
Cup Lid Assembly
KR-4001-B
9
Needle (** = 1.0, 1.4, 1.6, 1.8, 2.0, 2.2mm)
SP-300S-**-K
21
Lid Gasket - Kit of 3
KR-11-K3
10
Airvalve housing + seal
SP-612-K
22
Drip Free Diaphragm - Kit of 5
KR-115-K5
11
Spindle
-
23
Cup - Blue Anodised
KR-466-K
12
Trigger
SP-617-K
24
Complete Cup - Blue Anodised
KR-566-1-B
56
Catalogue 2012
Ref
No
1
Description
Part
Number
Ref
No
Description
Part
Number
GTi-W Air Cap / Retaining ring
GTi-407-115
10
Needle Adjusting Screw
GTi-414-K
GTi-G Air Cap / Retaining ring
GTi-407-110
11
Valve Assembly
JGK-449
PRi Air Cap / Retaining ring
PRi-407-310
12
Trigger
GTI-108
1a
Spring Clip
JGA-156-K5
13
Connector
JGA-158
2
GTi-W Nozzle (1.3, 1.4 & 1.5mm)
GTi-213-**-K
14
Gun Hook
GFG-6
GTi-G Nozzle (1.2, 1.3, 1.4 & 1.5mm)
GTi-213-**-K
15
Airflow Valve
GTi-415-K
PRi Nozzle (1.6, 1.8, 2.0, 2.2 & 2.5mm)
PRi-2-**-K
16
1⁄2 Ltr Gravity Cup Kit
GFC-501
3
Baffle & Seal
GTi-425-K
17
Cup Lid
GFC-402
4
Packing
5
Baffle Seal – Kit of 5
GTi-33-K5
18
Drip Check Lid kit of 5
GFC-2-K5
GTi-445-K2
19
Filter
KGP-5-K5
Spreader Valve
GTi-404-K
20
Circlip
25746-007-K5
6
Stud and Screw
GTi-408-K5
21
Circlip
SST-8434-K5
7
GTi Needle
GTi-413-K
22
Seal & Pin Kit (+SST8434-K5)
GTi-428-K5
PRi Needle
PRi-3-K
23
Washer
GFC-17-K5
GTi-409-K5
24
Spring
JGV-262-K5
Service Kit for GTI gravity and suction 12,13,14,15,16,18,20,22 nozzle
GTI-416-**
Service Kit for PRi - 16,18,20,22,25
nozzle
PRi-416-**
8
Spring and Pad
9
Bushing
GTi-402-K
9a
Seal kit of 5
JGS-72-K5
Catalogue 2012
57
Ref. No
Description
GTI-407-123
11
Valve Assembly
JGK-449
GTI-S air cap/retaining ring
GTI-407-110
12
Trigger
GTI-108
1a
Spring Clip
JGA-156-K5
13
Connector
JGA-158
2
GTI-P Nozzle
GTi-213-**-K
14
Airflow Valve
GTI-415-K
GTI-S Nozzle
GTI-214-**-K
15
Lock Nut
JGA-51-K5
3
Baffle & Seal
GTI-425-K
16
Seal
23165-001
3a
Baffle seal—Kit of 5
GTI-33-K5
17
Fluid Inlet Connector and seal
JGA-159-K
4
Packing
GTi-445-K2
18
Cup lid assembly
KR-4001-B
5
Spreader Valve
GTI-405-K
19
Lid Gasket - kit of 3
KR-11-K3
6
Stud and Screw
GTI-408-K5
20
Drip free diaphragm - kit of 5
KR115-K5
7
GTI-P needle
GTi-449-**-K
21
Cup
KR-466-K
22
Complete cup
KR566-1-B
Ref. No
Description
1
GTI-P air cap/retaining ring
Part
Number
Part
Number
GTi-S needle (for GTI-214 Tip)
GTI-420-K
8
Spring and Pad
GTI-409-K5
23
Circlip
25746-007-K5
9
Bushing
GTI-402-K
24
Circlip
SST-8434-K5
9a
Seal kit of 5
JGS-72-K5
25
Seal & Pin Kit
GTI-428-K5
10
Needle Adjusting Screw
GTI-414-K
26
Spring
JGV-262-K5
58
Catalogue 2012
Ref. No
Description
Part Number
Ref. No
Description
Part Number
1 (SRi)
Air Cap/Retaining ring Trans-Tech
SRI-407-210
11
Air Valve Assembly
SRI-404-K
SRI-407-200
12
Air Valve Stem Assembly
-
1 (SRiW)
Air Cap/Retaining ring HVLP
SRI-407-215
13
Trigger Stud and Screw Kit
SRI-412-K
2
Nozzle 0.7 mm & seal
SRI-2-07-K
14
Trigger
SRI-9-K
Nozzle 0.8 mm & seal
SRI-2-08-K
15 (SRi)
Air Inlet Adaptor
SRI-20-K
Nozzle 1.0 mm & seal
SRI-2-10-K
15 (SRiW)
Air Inlet Adaptor
SRI-40-K
Nozzle 1.2 mm & seal
SRI-2-12-K
16
SRI-21
Needle for 1.0 and 1.2 mm
Nozzle
SRI-3-K
Blanking Plug (to replace airflow
valve)
17
Airflow Valve
SRI-402-K
Needle for 0.7 and 0.8 mm
Nozzle
SRI-37-K
18
Cup
SRI-510
4
Needle Spring
SRI-18-K2
19
Aircap Seal
SRI-35-K5
5
Needle Adjusting Knob
SRI-19-K2
20
Airvalve Spring
SRI-23-K2
6 (SRi)
Spreader Valve
SRI-401-K
21
Airvalve Seal
-
6 (SRiW)
Spreader Valve
SRI-415-K
22
Retaining Ring
-
7
Body Bushing and Seal Kit
SRI-17-K
23
Filter
SRI-42-K3
8
Seal
SRI-16-K5
24
Airvalve Body
-
9
Separator
SRI-6-K5
25
Drip Check Lid Kit of 5
GFC-2-K5
10
Needle Packing Kit of 3
SRI-411-K3
Service Kit for SRi/SRI-W
SRI-416
3
Catalogue 2012
59
Ref Description
No
Part No.
Ref Description
No
Part No.
1
Air Cap Retaining Clip
JGA-156-K5
14
Colour ID Ring Kit (4 Colours)
SN-26-K4
2
Suction Feed Trans-tech® Aircap
VRIPRO-100-TV1-K
15
Airflow Valve
ADV-401-K
Pressure Feed Trans-tech® Aircap
VRIPRO-100-TV2-K
16
Fluid Inlet Connector and seal
ADV-7-K
3
Air Cap Retaining Ring & Seals
ADV-403-K
17
Cup lid assembly
KR-4001-B
4
Fluid Nozzle - 0.85,14, 16, 18
SP-200S-**-K
18
Lid Gasket - kit of 3
KR-11-K3
5
Separator
SP-626-K5
19
Drip free diaphragm - kit of 5
KR115-K5
6
Body Bushing & Seal
SN-6-K
20
Cup
KR-466-K
7
Fluid Needle - 0.85, 1.4, 1.6, 1.8 mm
ADV-310-**-K
21
Complete cup
KR-566-1-B
8
Fluid Adjusting Knob, Spring & Pad Kit
ADV-6-K
22
Filter
KR-484-K10
9
Spreader Valve Assembly
AV-401-K
23
Torx Key
SPN-8-K2
10
Packing, Spring & Packing Nut Kit
SN-404-K
24
Trigger Stud & Torx Screw (kit of 5)
SN-405-K5
SN-402-K
Service Parts
11
Air Valve Replacement Kit
12
Trigger, Stud & Screw Kit
SN-63-K
Spray Gun repair kit
PRO-415-1
13
Air Inlet
SN-9-K
Seal and Pin Kit, kit of 5
GTI-428-K5
60
Catalogue 2012
Ref
No
1
2
3
4
5
6
7
8
9
10
11
12
13
Description
Air Cap Retaining Clip
Gravity Feed Trans-tech® Air Cap
Air Cap Retaining Ring & Seals
Fluid Nozzle 12 or 13
Separator
Body Bushing & Seal
Fluid Needle 12 or 13
Fluid Adjusting Knob, Spring & Pad Kit
Spreader Valve Assembly
Packing, Spring & Packing Nut Kit
Air Valve Replacement Kit
Trigger, Stud & Screw Kit
Air Inlet
Catalogue 2012
Part No.
JGA-156-K5
VRIPRO-100-TV1
ADV-403-K
SP-200S-XX-K
SP-626-K5
SN-6-K
ADV-310-XX-K
ADV-6-K
ADV-402-K
SN-404-K
SN-402-K
SN-63-K
SN-9-K
Ref Description
No
14 Colour ID Ring Kit (4 Colours)
15 Airflow Valve
16 Gravity Cup Kit
17 Drip Check Lid (kit of 5)
18 Gravity Cup Lid
19 Filter
20 Spanner, Torx, Brush & ID Rings
21 Torx Key
22 Trigger Stud & Torx Screw (kit of 5)
Service Parts
Spray Gun repair kit
Seal and Pin Kit, kit of 5
Part No.
SN-26-K4
ADV-401-K
GFC-501
GFC-2-K5
GFC-402
KGP-5-K5
SN-406
SPN-8-K2
SN-405-K5
PRO-415-1
GTI-428-K5
61
Ref. No
Description
Part No.
Ref. No
Description
Part No.
1
Air Cap/Retaining ring (* = 186+
or 30+)
AV-4239-***
12
Trigger
GTI-108
1a
Spring Clip - Kit of 5
JGA-156-K5
2
Nozzle (* = EX-1.8mm, FF-1.4mm,
FW-1.6mm)
AV-645-*
3
Baffle & Seal
JGD-402-K
3a
Baffle seal - Kit of 5
GTI-33-K5
4
Packing
GTi-445-K2
5
Spreader Valve
GTI-405-K
6
Stud and Screw
GTI-408-K5
7
Needle (* = DEX or FF)
JGA-421*-K
8
Spring - Kit of 5
GTI-409-K5
9
Bushing
JGA-17
9a
Seal - Kit of 5
JGS-72-K5
10
Needle Adjusting Screw
GTI-414-K
11
Valve Assembly
JGK-449
62
13
Connector
JGA-158
14
Airflow Valve
GTI-415-K
15
Lock Nut - Kit of 5
JGA-51-K5
16
Seal
23165-001
17
Fluid Inlet Connector and seal
JGA-159-K
18
Cup lid assembly
KR-4001-B
19
Lid Gasket - kit of 3
KR-11-K3
20
Drip free diaphragm - kit of 5
KR115-K5
21
Cup
KR-466-K
22
Complete cup
KR-566-1-B
23
Circlip
25746-007-K5
24
Circlip
SST-8434-K5
25
Seal & Pin Kit ( + SST-8434-K5)
GTI-428-K5
26
Spring
JGV-262-K5
Catalogue 2012
Ref
No
Description
Part Number
Ref
No
Description
Part Number
1
Air Cap/Retaining ring * = 186 or 30
AV-4239-*
12
Trigger
GTI-108
1a
Spring Clip
JGA-156-K5
13
Connector 1/4
JGA-158
2
Nozzle (* = EX-1.8mm, FF-1.4mm, FW1.6mm)
AV-645-*
14
Gun Hook
GFG-6
3
Baffle & Seal
JGD-402-K
15
Airflow Valve
GTI-415-K
4
Packing (kit of 2)
GTi-445-K2
16
1/2 Ltr Gravity Cup Kit
GFC-501
5
Spreader Valve
GTI-404-K
6
Stud and Screw
GTI-408-K5
7
Needle (* = DEX or FF)
JGA-421-*-K
8
Spring
GTI-409-K5
9
Bushing
JGA-17
9a
Seal - kit of 5
JGS-72-K5
10
Needle Adjusting Screw
GTI-414-K
11
Valve Assembly
JGK-449
Catalogue 2012
17
Cup Lid
GFC-402
18
Drip Check Lid kit of 5
GFC-2-K5
19
Filter
KGP-5-K5
20
Circlip
25746-007-K5
21
Circlip
SST-8434-K5
22
Seal & Pin Kit
GTI-428-K5
23
Washer
GFC-17-K5
24
Spring
JGV-262-K5
63
Ref
No
Description
Part Number
1
Vizor Assembly (Ref Nos 2-10)
MPV-526
2
Quick Detachable Stem
MPV-20
Ref
No
Description
Part Number
3
Clear Vizor (kit of 5)
MPV-478-K5
13
Regulator and Housing
MPV-455
4
Vizor Covers (kit of 10)
MPV-44-K10
14
Disposable Filter
MPV-22
5
Face Cartridge — Foam (kit of 5)
MPV-476-K5
15
Waistbelt and Filter Housing
MPV-519
6
Face Cartridge — Tyvek (kit of 5)
MPV-477-K5
16
Quick Detachable Stem
MPV-10
7
Neck Covers (kit of 5)
MPV-24-K5
17
Quick Detachable Connector
MPV-424
8
Hoods (kit of 5)
MPV-2-K5
18
10m length M-F QD Fittings #
H-6085-QD
9
Stowage Bag
MPV-458
10m length 1/4” Re-usable Fittings #
H-6065-B
10
Tube and Diffuser Assembly
MPV-457
19
Gun Hose Assembly
MPV-456
11
Waistbelt Assembly
MPV-518
20
Quick Detachable Stem
MPV-5
12
Quick Detachable Connector
MPV-442
# Not part of outfit, order separately
64
Catalogue 2012
Ref
No
Description
Part
Number
Ref
No
Description
Part
Number
1
Face mask assembly (Ref Nos 2-8)
MPV-517
10
Regulator and housing
MPV-455
2
Browguard assembly
MPV-453
11
Disposable filter
MPV-22
3
Face mask & seal assembly
MPV-454
12
Waistbelt and filter housing
MPV-519
4
Kit of 10 face mask covers
MPV-1-K10
13
Quick detachable stem
MPV-10
5
Kit of 5 neck covers
MPV-24-K5
14
Quick detachable connector
MPV-424
6
Kit of 5 hoods
MPV-2-K5
15
Gun hose assembly
MPV-456
7
Tube and diffuser assembly
MPV-457
16
Quick detachable assembly
MPV-5
8
Quick detachable stem
MPV-20
17
Stowage bag
MPV-458
9
Quick detachable connector
MPV-442
18
Waistbelt assembly
MPV-518
# Not part of outfit, order separately
Catalogue 2012
65
Conditions of Sale
ITW Finishing Systems and Products, A Division of ITW Limited (“ITW”)
comprehensively any changes or interferences on the prints.
1. INTERPRETATION
1.1 In these Conditions:
4.3. If Goods are to be made or any process is to be applied in
accordance with a specification, drawing or design submitted
by the Buyer, the Buyer shall indemnify ITW against all loss,
damages, costs and expenses awarded against or incurred by
ITW in connection with or paid or agreed to be paid by ITW in
settlement of any claim for infringement of any third party rights
which results from ITW’s use of such material.
4.4. If any claim is made against the Buyer that the Goods supplied
or their proper use infringe the intellectual property rights of any
other person, ITW shall indemnify the Buyer against all damages,
costs and expenses awarded against the Buyer in connection with
the claim provided that:
Business Day: a day (other than a Saturday, Sunday or public
holiday) when banks in London are open for
business.
Buyer:
Is the person who accepts ITW’s quotation or
whose order is accepted by ITW.
Conditions: Are these conditions of sale and (unless the
context otherwise requires) includes any
special terms on the face of ITW’s quotation or
acceptance of the Buyer’s order.
Contract: Is the contract for the purchase and sale of the
Goods and/or supply of services.
Goods:
Are the goods which ITW is to supply.
4.4.1. ITW is given full control of any proceedings or
negotiations in connection with any such claim;
4.4.2.
2. BASIS OF THE SALE
2.1.
Subject to ITW’s quotation, all Goods are sold and services
supplied subject to these Conditions to the exclusion of any other
terms and conditions.
2.2. No variation to these Conditions shall be binding unless agreed
in writing by a general manager of ITW.
2.3.
ITW’s employees or agents are not authorised to make any
representations unless confirmed by ITW in writing. The Buyer
acknowledges that it does not rely on, and irrevocably waives
any claim it may have for damages for or the right to rescind the
Contract for any such representations which are not so confirmed
(unless such representations were fraudulently made).
the Buyer shall pay to ITW all damages and costs (if
any) awarded in favour of the Buyer which are payable
by, or agreed with the consent of the Buyer (which
consent shall not be unreasonably withheld) to be paid
by, any other party in respect of any such claim; and
4.4.3. without prejudice to any duty of the Buyer at common
law, ITW may require the Buyer to take such steps as
ITW may reasonably require to mitigate or reduce any
such loss, damages, costs or expenses for which ITW is
liable to indemnify the Buyer under this condition.
5. PREPARATION OF SITE
5.1. The Buyer shall obtain all necessary licences, permits and
permissions.
2.4.
Any advice or recommendation given by ITW or its employees
or agents to the Buyer or its employees or agents which is not
confirmed in writing by ITW is followed or acted upon entirely
at the Buyer’s own risk and ITW shall not be liable for any such
advice or recommendation which is not so confirmed.
5.2. The Buyer shall clear the site for installation and make it ready for
the reception of the Goods. The Buyer shall keep the site free from
water, debris and obstructions, and make required alterations
to buildings and other equipment if required for the proper
clearance and support of the Goods.
2.5. Any typographical, clerical or other error or omission in any sales
literature, quotation, price list, acceptance of offer, invoice or
other document or information issued by ITW shall be subject to
correction without any liability on the part of ITW.
5.3. The Buyer shall ensure that ITW shall not be delayed by the
operations of others (including the Buyer) or the Buyer’s failure to
provide the conditions and facilities required. If such delays cause
extra visits by ITW, these will be charged in addition.
5.4. The Buyer shall, at its own risk, unload the Goods and store them
close to the point of erection, provide safe and convenient storage
room for tools and materials, provide adequate work room
for ITW personnel, give proper care to and provide insurance
against loss by fire and theft for all materials and equipment prior
to, during and after installation.
3. ORDERS AND SPECIFICATIONS
3.1. Quotations are valid for 60 days only. No order submitted by the
Buyer shall be deemed to be accepted by ITW unless and until
confirmed in writing by ITW.
3.2. The Buyer is responsible for ensuring the accuracy of the terms of
any order and for giving ITW any necessary information within a
sufficient time to enable ITW to perform the Contract.
6.1. ITW reserves the right to make any changes in the specification
of the Goods (including materials and components) which are
required to conform with any applicable law or, which do not
materially affect their quality or performance.
The Buyer shall provide the necessary foundations required, carry
out cutting away and making good, and grouting in foundation
bolts etc, and will provide a level concrete floor for the plant of
adequate strength. The Buyer shall be entirely responsible for the
exact siting of the Goods to meet the Buyer’s requirements.
6.2. An order once accepted by ITW may only be cancelled with
its written agreement and the Buyer shall indemnify ITW in full
against all loss (including loss of profit), costs (including labour
and materials) and damages incurred by ITW.
All gas, water, electrical and compressed air services (including
interconnecting wiring) shall be provided by the Buyer. All
building work such as cutting holes etc for stacks to be undertaken
by the Buyer.
6.3. If ITW undertakes any of the work detailed in the previous
paragraphs to complete installation, such work shall be
charged in addition and ITW shall not be responsible for any
consequential damage.
3.3. The quantity and description of and any specification for the
Goods or services shall be those set out in ITW’s quotation (if
accepted by the Buyer) or ITW’s acceptance of the Buyer’s order.
3.4. 3.5. 6. INSTALLATION LIABILITY
4. DRAWINGS AND SPECIFICATIONS
4.1. 4.2. Any specifications or drawings supplied remain ITW’s sole
property and are subject to recall at any time before ITW’s
quotation is accepted. Any drawings supplied are not to be used
for construction purposes. Where ITW’s quotation includes a
drawing reference, copy of any approved prints or equipment
data sheets, these must be signed by the Buyer and must
accompany the equipment purchase order.
Before signing the prints the Buyer shall check equipment size,
location of building, and all interferences as shown on the
drawings, data sheets etc and clearances and note clearly and
66
7. PLANT ACCEPTANCE/TAKING OVER
7.1. The Goods shall be deemed to have been accepted at the earlier
of:
7.1.1.
When installation has been completed and the Goods
have passed or are deemed to have passed all tests
provided for in ITW’s proposal; or
7.1.2. One calendar month after the Goods shall have been put
into use.
Catalogue 2012
7.2. The time of acceptance shall not be delayed because of
additions, minor omissions or defects which do not materially
affect the use of the Goods or if the Buyer is preventing ITW from
completing the Contract.
immediately due and payable). Until then the Buyer shall:
11.2.1. hold the Goods as ITW’s fiduciary agent and bailee,
and shall keep them separate from all other goods and
properly stored, protected and insured and identified as
ITW’s property but may resell or use the Goods in the
ordinary course of its business;
8 PRICE
8.1. The price shall be ITW’s quoted price (or if a quoted price is no
longer valid), the price stated in ITW’s acknowledgement of order.
Prices are ex works.
8.2. ITW may, by giving notice to the Buyer at any time before
delivery, increase the price to reflect any increase in the cost to
ITW which is due to any factor beyond the control of ITW.
8.3. Any applicable value added tax or other taxes or duties are
payable by the Buyer in addition.
8.4. Goods for export will be packed in good quality export cases at
the Buyer’s cost. Any special packing requirements of the Buyer
will attract an additional charge. Packing for parcel post or air
freight will be in an appropriately economic manner using cartons
and/or parcels.
9. TERMS OF PAYMENT
9.1. Payment shall be made in accordance with ITW’s quotation.
9.2. ITW may recover the price, notwithstanding that delivery may not
have taken place and the property in the Goods has not passed.
The time of payment shall be of the essence of the Contract.
9.3. 11.2.2. (provided the Goods are still in existence and have not
been resold), deliver up the Goods to ITW on demand
11.2.3. and, if the Buyer fails to do so immediately, ITW may
enter any premises of the Buyer or any third party where
the Goods are stored and repossess the Goods.
12. WARRANTIES AND LIABILITIES
12.1. ITW warrants that it holds unencumbered title to the Goods and
will perform services with reasonable skill and care.
12.2. Subject to condition 12.3, ITW warrants that the Goods will
correspond with their specification at the time of delivery and will
be free from defects in material and workmanship for 12 months
from delivery.
12.3. The above warranty does not apply to any defect:
12.3.1. arising from any drawing, design or specification
supplied by the Buyer;
12.3.2. arising from fair wear and tear, improper use, storage
or installation or maintenance, failure to follow ITW’s
instructions (whether oral or in writing), or alteration or
repair of the Goods without ITW’s approval;
ITW may charge the Buyer interest (both before and after any
judgement) on the amount unpaid, at the rate of 4 per cent per
annum above the base rate from time to time of HSBC Bank plc
until payment in full is made.
12.3.3. which is not immediately notified in writing to ITW;
12.3.4. if any sum owing by the Buyer to ITW has not been
paid;
10. DELIVERY
10.1. The method of delivery shall be in accordance with ITW’s
quotation. The Buyer must obtain any import or export licences
required.
10.2. Any dates given for delivery of the Goods or provision of services
are approximate only and ITW shall not be liable for any delay
howsoever caused. Time for delivery or performance shall not be
of the essence.
10.3. The Goods may be delivered in instalments. Each delivery shall
constitute a separate contract and failure by ITW to deliver
any one or more of the instalments in accordance with these
Conditions or any claim by the Buyer in respect of any one or
more instalments shall not entitle the Buyer to treat the Contract as
a whole as repudiated.
10.4. If the Buyer fails to take delivery of the Goods or fails to give ITW
adequate delivery instructions within 14 days of their availability
ITW may:
10.4.1. store the Goods until actual delivery and charge the
Buyer for the costs (including insurance) of storage; or
10.4.2. sell the Goods at the best price readily obtainable and
(after deducting all storage, selling and other expenses)
account to the Buyer for the excess over sums owing by
the Buyer or charge the Buyer for any shortfall.
10.5. Where ITW arranges forwarding of the Goods, the Buyer shall
notify ITW and the carrier in writing within 48 hours of delivery of
any damage to the Goods or shortage in delivery.
10.6. The Buyer shall inspect the Goods on receipt and notify ITW of
any defects within 7 days of delivery failing which the Buyer
shall be deemed to have accepted them. After acceptance the
Buyer shall not be entitled to reject Goods. The Buyer shall not be
entitled to reject the Goods for any defect or failure which is so
slight that it would be unreasonable to reject them.
11. RISK AND PROPERTY
11.1. Risk in the Goods shall pass to the Buyer when ITW notifies the
Buyer that the Goods are available for collection or when the
Goods leave ITW’s premises, whichever is the earlier.
11.2. Notwithstanding any other provision of these Conditions, the
property in the Goods shall not pass to the Buyer until ITW has
received in cash or cleared funds payment in full of all sums due
under the Contract and all other contracts between the Buyer
and ITW (whether or not the sums due under those contracts are
Catalogue 2012
12.3.5. in items not manufactured by ITW, when the Buyer shall
only be entitled to the benefit of any such warranty as is
given to ITW by the manufacturer.
12.4. ITW shall replace or repair free of charge the Goods (or the part
in question) returned to ITW’s factory carriage paid which do not
meet the warranty in condition 12.2 or, at ITW’s sole discretion,
refund to the Buyer the price of the Goods (or a proportionate
part of the price) but ITW shall have no further liability to the
Buyer. The warranty on replacements or repairs shall be to the
end of the original warranty period. Repairs and replacements
will be delivered free within the UK and to the nearest port or
airport c.i.f. outside the UK.
12.5. Subject as expressly provided in these Conditions, all warranties,
conditions, representations or other terms implied by statute or
common law are excluded to the fullest extent permitted by law.
12.6. The following provisions set out ITW’s entire liability whether
arising in contract, tort (including negligence), misrepresentation
(other than fraudulent misrepresentation) or otherwise howsoever
arising.
AND THE BUYER’S ATTENTION IS IN PARTICULAR
DRAWN TO THE FOLLOWING PROVISIONS OF THIS
CONDITION
12.7. To the extent the law does not permit such liability to be excluded:
12.7.1. ITW’s liability to the Buyer for death or injury resulting
from its negligence shall not be limited;
12.7.2. ITW accepts liability to the Buyer for damage to
the tangible property of the Buyer resulting from the
negligence of ITW not exceeding £1,000,000 for
any one incident or series of incidents arising from a
common cause;
12.7.3. Save as otherwise expressly provided, ITW’s entire
liability shall be limited to damages of an amount equal
to the price due under the Contract.
12.8. Subject to condition 12.7.1 above, ITW shall not be liable for
any increased costs, expenses, loss of profits, goodwill, business,
contracts, revenues or anticipated savings or any type of special
indirect or consequential loss (including loss or damage suffered
by the Buyer as a result of a claim by a third party) even if such
loss was reasonably foreseeable or ITW had been advised of the
possibility of the Buyer incurring the same.
67
12.9. ITW shall not be liable to the Buyer or be deemed to be in
breach of the Contract by reason of any delay in performing, or
any failure to perform, any of ITW’s obligations, if the delay or
failure was due to any cause beyond ITW’s reasonable control
including (without limitation) flood, fire, accident, transportation
delays, strikes, war or threat of war, sabotage, civil disturbance
or governmental action, disruption of supplies or services.
12.10. Save as otherwise expressly provided, the Buyer shall indemnify
ITW against any cost, claim, expense, loss or liability made by
any person in connection with the Goods or their use.
13. INSOLVENCY AND BREACH
jurisdiction, whether concurrently or not, to the extent permitted by
the law of such other jurisdiction.
16.10. No term of this contract shall be enforceable under the Contracts
(Rights of Third Parties) Act 1999 by a third party.
16.11 These Conditions are drafted in the English language. If these
Conditions are translated into any other language, the English
language text shall prevail.
16.12 Any notice given under or in connection with the Contract shall be
in the English language. All other documents provided under or in
connection with the Contract shall be in the English language.
13.1. If the Buyer fails to make any payment when due or breaches any
provision of the Contract; or ITW reasonably apprehends that
the solvency of the Buyer may be in jeopardy ITW may cancel
the Contract or suspend any further deliveries under the Contract
without any liability to the Buyer, and if the Goods have been
delivered but not paid for the price shall become immediately
due and payable notwithstanding any previous agreement or
arrangement to the contrary.
14. SAFETY, OPERATING AND MAINTENANCE INSTRUCTIONS
The Buyer’s attention is directed to the instructions for use and
cautionary notes supplied with the Goods, as well as other
technical literature.
15. STANDARD OF COATING ATTAINED
The Buyer shall follow ITW’s instructions on operation and
maintenance. ITW accepts no responsibility for unsatisfactory
results due to use of coating materials not recommended in
writing by ITW or whose composition or quality when supplied is
different from that tested by ITW when giving its recommendation.
16. GENERAL
16.1. ITW may assign its rights and obligations. The Buyer may not
assign its rights and obligations.
16.2. Any notice shall be in writing addressed to the addressee at
its registered office or principal place of business or such other
address as may have been notified by the party giving the notice.
16.3. Any notice is deemed to have been received:
16.3.1. if delivered personally, at the time of delivery; or
16.3.2. if sent by commercial courier, at the time of signature of
the courier’s delivery receipt; or
16.3.3. in the case of pre-paid first class post or recorded
delivery, 9.00 am on the second Business Day after
posting; or
16.3.4. in the case of airmail, 9.00 am on the fifth Business Day
after posting.
16.4.
No delay or failure by ITW in enforcing or partially enforcing any
provision of the Contract shall constitute a waiver of that provision
or any other provision. No waiver by ITW shall be considered
as a waiver of any subsequent breach of the same or any other
provision. No waiver by ITW shall be effective unless in writing.
16.5. If any provision of these Conditions is held by any competent
authority to be invalid or unenforceable in whole or in part
the validity of the other provisions of these Conditions and the
remainder of the provision in question shall not be affected.
16.6. These Conditions constitute the entire agreement between ITW
and the Buyer concerning the supply of the Goods and replace
and supersede any prior arrangement, understanding, warranty
or representation (other than any fraudulent misrepresentation).
16.7.
ITW’s rights are cumulative and in addition to any rights
available to it at common law.
16.8. The Contract shall be governed by the laws of England and Wales
and, subject to clause, 16.9 the parties submit to the exclusive
jurisdiction of the courts of England and Wales. For the avoidance
of doubt, the United Nations Convention on the International Sale
of Goods shall not apply to the Contract.
16.9.
Nothing in these Conditions shall limit the right of ITW to take
proceedings against the Buyer in any other court of competent
jurisdiction, nor shall the taking of proceedings in any one or
more jurisdiction preclude the taking of proceedings in any other
68
Catalogue 2012
Catalogue 2012
69
70
Catalogue 2012
A guide to the DSEAR and ATEX Directives
What is DSEAR and ATEX?
The EU Directives 94/4/EC (ATEX 95) “Equipment for use in potentially explosive atmospheres” and the “Workplace directive” 1999/92/
EC (ATEX 137) are the European directives, which ensure employers work practices and manufacturers of equipment used in potentially
explosive atmospheres, are safe and do not create potential explosion hazards. In other words, its all about health and safety at work for
workers who handle and work with flammable and dangerous materials, to ensure they are not at risk of an explosion from the equipment
and work practices.
The ATEX directives are implemented into UK law by the regulations “Dangerous Substances and Explosive Atmospheres Regulations”
known as DSEAR 2002 and the “Equipment and protective systems for use in potentially explosive atmospheres” regulations 1996. DSEAR
became mandatory in July 2006. DSEAR is a legal Health and Safety requirement which is enforced by the HSE, local authorities and in
part the fire service.
ATEX Compliance
As a manufacturer of equipment used in potentially
explosive atmospheres, we comply with this directive by
applying the CE mark along with the Explosion protection
symbol
and other markings to show compliance
of that product.
Each piece of equipment must be marked with information
to enable the user to assess its suitability to be used in the
environment it is intended to be used in. The equipment
could be marked with the following;
l Name and address of Manufacturer
l The CE mark
l If the equipment has been certified by a Notified
Body, their reference follows the CE mark
l Equipment model number/name/type
l Year of manufacture
l The Explosion protection Symbol
l The equipment Group II and category 1, 2 or 3
l For Gas (G) e.g. Group 2, Cat 2 Gas
Typical Markings found on Hazardous Area Equipment
Name and Address
of Manufacturer
Specific Marking of
Explosive Protection
Equipment
Group
Category
Protection
Concept
CE Mark
and number
of Notified
Body
Gas Group
Temperature
Class
Ambient
Temperature
range
Model
or Type
EC Type Examination
Certificate Number
Gas
or Dust
Example of DGi Serial Number:
First 2 numbers denote year, 3rd and 4th
denote month, eg March = 03, 5th and
6th denote day. remaining 5 numbers
are sequential, reset at 00001 at start of
New Year.
Workplace regulations DSEAR 2002
The ATEX 1999/92/EC workplace regulations are
implemented in the UK through the DSEAR 2002
Regulations. The duties for employers and owners under
DSEAR are;
l Carry out a risk assessment of work involving
dangerous substances and eliminate or reduce any
risks identified.
l Provide equipment and procedures for accidents and
emergencies.
l Instruct and train employees.
l Areas where hazardous explosive atmospheres may
occur are classified into zones and where necessary
marked with a specified “EX” sign at their points of
entry; (eg spray booths, mix rooms, paint stores etc).
l Provide equipment and protective systems which
comply with ATEX Regulations appropriate for the
Zone rating of the hazardous area.
l Document all the above in an Explosion Protection
Document.
Typical Markings found on Sprayguns
Name and Address
of Manufacturer
Equipment Group
Category 2
CE Mark
Model or Type
Special
Conditions for
safe Use
Gas
Avoidance of Hazards associated with Spraying flammable materials
The main hazard with spraying is electrostatic discharges and mechanically generated sparks. To avoid these ignition hazards, you
should;
l Only use equipment CE marked to ATEX regulations. Most ITW Finishing Products are CE marked to ATEX eg Sprayguns, Digital
Gauge, hoses. If in doubt, contact your distributor or ITW Finishing.
l The equipment must be installed and used in accordance with the instructions provided by the manufacturer(s).
l Ensure metallic parts of the equipment are earthed and bonded together (e.g. pressure feed tanks and pumps) to avoid potential
differences between them. Metallic portable containers must be bonded and earthed. Check earth continuity at regular intervals. Keep
earthing points clean.
l Use conductive air and fluid hoses to avoid static charging from air and fluid flows.
l Equip Operators with anti-static clothing and conductive footwear. Remove contaminated clothing if leaving the workplace into areas
where ignitions hazards may occur e.g. smoking.
l Clean equipment with non-flammable liquids, or use safety cans with flame arrestors for use with flammable liquids.
l Removal of paint residues with scrapers made of plastic or non-sparking materials (steel scrapers can create sparks). Coat walls with
strippable/peelable coatings to avoid removal of residues by mechanical means.
More information can be found at the HSE DSEAR website: http://www.hse.gov.uk/fireandexplosion/dsear.htm
Catalogue 2012
71
72
Catalogue 2012
Download PDF
Similar pages