Introduction
Important Information and
Customer Assistance
Important Information
Operating Instructions
The Cobra line of quality products includes:
Federal Laws Governing the Use of Radar Detectors
It is not against federal law to receive radar transmissions with your Cobra radar/
laser detector. The Communications Act of 1924 guarantees your right to receive
radio transmissions on any frequency. Local laws that contravene this Act, while illegal,
may be enforced by your local law enforcement officials until and unless
they are prohibited from doing so by federal court action.
Safe Driving
Motorists, as well as operators of emergency or service vehicles, are expected to
exercise all due caution while using this product, and to obey all applicable traffic
laws. Do not attempt to change settings of the unit while in motion.
Security of Your Vehicle
Before leaving your vehicle, always remember to conceal your radar detector
in order to reduce the possibility of break-in and theft.
CB Radios
Dash Cams
Radar Detectors
Customer Assistance
Marine VHF Radios
Power Inverters
Accessories
For more information or to
order any of our products,
please visit our website:
www.cobra.com
Nothing Comes Close to a Cobra®
English
RADAR/LASER PROTECTION
RAD500G
Please go to www.cobra.com
to download the Spanish
versionof this manual.
Printed in the Philippines
Part No. 480-1107-P
Version A
©2017 Cobra Electronics Corporation
6500 West Cortland Street
Chicago, Illinois 60707 USA
www.cobra.com
Nothing Comes Close to a Cobra®
A1
Controls Indicators and Connections
Introduction
Controls, Indicators and Connections
12V DC
Power Jack
Speaker
Menu Button
To select
detector
settings.
Windshield
Bracket
Mount
•
False Button
Press to lock out false
alerts. Press and hold
to set user locations.
USB
Port
Introduction
Display and Product Features
Easy-to-Read Display
Signal Strength
Radar Band
Radar/Laser Protection
Detects all radar and laser guns.
LaserEye
Detects laser signals from both front and rear.
Dim Button
For adjusting the
display brightness.
Mute Button
For manual mute of audio
alerts, changing standby
screens, turning Quiet
Drive on/off.
SEN Button
Adjust sensitivity
and filtering modes
to reduce unwanted
alerts.
Frequency
Congratulations! You’ve made a smart choice by purchasing a radar/laser
detector from Cobra. Just look at some of the sophisticated features and
capabilities your new unit includes:
Manual Lock-Out
Allows you to lock-out locations with false alerts.
On-Off/Volume Control
Allows you to adjust the
volume of the alerts.
•
Product Features
GPS-Ready
Internal GPS receiver alerts you to known speed
trap and red light/speed camera locations.
LaserEye
For detection of
rear laser signals.
NOTES
VoiceAlert
Digital voice announcements keep your eyes on
the road.
QuietDrive™
Quiet Drive is a muted driving mode for times
when a driver wants less audible feedback while
talking with passengers, on the phone, etc.
Premium Anti-Falsing Circuitry
Automatically reduces false alerts from
erroneous sources including vehicle collision
avoidance systems, traffic flow monitoring
devices and other radar detectors.
•
Updatable IVT FilterTM
User updatable system automatically reduces
false alerts from moving In-Vehicle Technology
sources such as collision avoidance systems and
adaptive cruise control.
White OLED Display
Bright display with band identification icons
and numeric signal strength meter.
Sensitivity Modes
Multiple sensitivity modes to reduce
false alerts.
Auto Mute
Automatically mutes audio for sustained
alerts.
Dual Language
English and Spanish voice and text alerts.
User Updates
Micro-USB port allows users to access
future software updates as well as download
the latest known speed trap and red-light/speed
camera locations.
This booklet describes the simple steps for mounting and setting up your detector.
It also provides helpful information about how radar and laser guns are used and
how you can interpret the alerts you receive.
A2
English
Nothing Comes Close to a Cobra®
A3
Nothing Comes Close to a Cobra®
20
Contents
Introduction
Introduction
Important Information. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Controls, Indicators and Connections. . . . . . . . . . . . . . . . . . . . . .
Display. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Product Features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Main Icons
Intro
Operation
Secondary Icons
Notice
n Icons
Intro
ondary Icons
Operation
Customer
Assistance
A1
A2
A3
A3
Your Detector
Installation. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2
Getting Started . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
Buttons . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
Customer
Warranty
SEN. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
Assistance
Using the FALSE Button . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
MUTE. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
Quiet Drive . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
Battery Voltage. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
DIM. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
Menu-User Settings. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
Detail. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
AutoMute. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
Language . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
Screen Saver. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
Smart Power. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
System Info. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
Restore Defaults. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
Menu-Alert Settings. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
Low Car Voltage . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
Radar Alerts. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
Radar Detector-Detector Alerts. . . . . . . . . . . . . . . . . . . . . . . . . . . 10
Understanding Radar and Laser . . . . . . . . . . . . . . . . . . . . . . . . . . 10
Radar Speed Monitoring Systems. . . . . . . . . . . . . . . . . . . . . . . 10
VG-2 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
Spectre RDD. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11
Laser Alerts. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11
LIDAR . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11
Menu-GPS Settings. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12
Location-Based Alerts (LBAs). . . . . . . . . . . . . . . . . . . . . . . . . . 12
Customer Information
Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13
Warranty
Maintenance. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13
Limited 1-Year Warranty . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14
Product Service & Optional Accessories. . . . . . . . . . . . . . . . . . . 15
FCC Statement & Trademark Acknowledgement. . . . . . . . . . . . . . 16
Nothing Comes Close to a Cobra®
1
Installation
Your Detector
Intro
Operation
Customer
Warranty
Intro
Assistance
Installation
Where to mount your unit
•
You will get optimum performance from your detector if you mount it at a point
approximately in the center of the vehicle, as low as possible on the front windshield
without obstructing the unit’s view of the road either to the front or rear. You can
also mount it directly on the dashboard. Make sure the detector is level/parallel to
the road.
Secondary Icons
Windshield
Mounting
Notice
Installation
Your Detector
Dashboard Mounting
Operation
Customer
Assistance
Windshield mounting
Warranty
1. Attach the rubber cups
to the bracket.
Secondary Icons
2. Make sure the rubber cups and your windshield are clean.
Notice
3. Push the bracket firmly onto
the windshield.
4. Attach the detector to
the bracket. Check that
the unit is parallel to the
road’s surface.
The detector must level/parallel to the road
5. To adjust the angle if
necessary, gently push or
pull on the bracket to bend
it. DO NOT use the detector
to bend the bracket.
Incorrect
Incorrect
Correct
Radar and laser signals pass through glass but not through other materials and
objects. Objects that can block or weaken incoming signals include:
n
Windshield wiper blades
n
Mirrored sun screens
n
Dark tinting at the top of the windshield
n
2
English
Heated windshields currently available on some vehicles
(Instaclear for Ford, Electriclear for GM). Consult your dealer
to see if you have this option.
6. Plug the power cord
into the detector.
7. Plug the cigarette lighter
adapter on the power cord
into your vehicle’s cigarette
lighter.
Nothing Comes Close to a Cobra®
3
Installation
Your Detector
Intro
Operation
Customer
Assistance
Dashboard Mounting
Warranty
Getting Started
Your Detector
Intro
Operation
Customer
Getting
Started
Assistance
Warranty
•
To Turn On The Unit And Adjust The Audio Volume
1. P lace the detector on the dashboard to find a location
where the unit has a clear, level view of the road and is
parallel to the road’s surface. The angle CANNOT be
adjusted after mounting
Secondary Icons
Notice
2. Remove the paper backing
from one side of the hookand-loop fastener.
3. Attach the pad to the
dashboard at your chosen
location and remove the other paper backing.
4. Attach the detector to the
hook-and-loop fastener. You
can remove and reattach the
unit as often as you like.
5. Plug the power cord into the
detector.
6. Plug the cigarette lighter
adapter on the power
cord into your vehicle’s
cigarette lighter.
4
English
Rotate the On-Off/Volume
control clockwise (away
from you).
Secondary Icons
When GPS signals are
acquired. Notice
Audible Tone
Visual Display
“Testing”
Three beeps
“System Ready”
Audible Tone
Visual Display (GPS locked)
Chime
NOTE: In some vehicles, power is supplied to the cigarette lighter even
while the ignition is Off. If this is the case with your vehicle, you should
turn Off or unplug your detector when parking for lengthy periods.
SEN Button
Setting your detector to Low
or Medium
sensitivity delays the audio alerts
for weak X band and K band signals until they become stronger. (A single beep
will sound when the signal is first detected.) Also, additional filtering is done to
reduce false alerts while you are driving in, or near, urban areas where there are
many sources for conflicting X and K band signals such as microwave towers and
automatic door openers.
Icon
Sens Level
For
High
No filtering for maximum range
Medium
Minimal filtering to reduce unwanted alerts
Low
Maximum filtering to reduce unwanted alerts
Auto
When GPS is active, Auto Sens will automatically adjust
the SENS level based on your speed.
Using the FALSE Button
Manually lock-out false alerts from X and K band door openers and other annoying places. Please be careful to lock-out only those sources that you know are
permanent. An alert can be unlocked by pressing and holding the FALSE button
during that alert. You can also set your User Locations by pressing and holding
the FALSE button for a few seconds.
Nothing Comes Close to a Cobra®
5
Settings
Your Detector
Intro
Operation
Customer
MUTE ButtonAssistance
Warranty
Manual Mute: Your detector allows you to quickly turn OFF an audio alert by
momentarily pressing the MUTE button. If you press the MUTE button a second
time during the alert, the audio alert will be turned back ON. When an alert is
Secondary
Icons muted the audio icon on the display will change to
being
Your Detector
Intro
Settings
Operation
Customer
Warranty
Menu - UserAssistance
Settings
•
To change the User settings, enter the Menu by pressing the MENU button. A voice
announces “Menu” and the display will change to
Secondary Icons
USER GPS
ALERT
Press the DIM button to enter the User settings menu.
Press the MUTE or MENU
Notice
Quiet Drive is a muted driving mode for times when a driver wants less audible
feedback while talking with passengers, on the phone, etc. Only the first few
seconds of audio will be heard. This mode is Off by default.
This mode can be changed in the User Settings menu or by pressing and holding
the MUTE button for two seconds. When Quiet Drive is on the audio icon on the
display will change to
Battery Voltage
To display your vehicle’s battery voltage, press the MUTE button momentarily
while no signal is being detected.
DIM Button
You can choose from four settings for the brightness of the display. Repeatedly
push the DIM button to cycle through the settings. The factory setting is Bright.
buttons to switch between the User settings.
Notice
Press the DIM
or SEN buttons to change the selected User setting’s value.
The value that is shown on the display is the selected value. To exit the menu
simply wait several seconds or select Exit Menu.
USER SETTING
VALUE
Detail
More*/Less
Quiet Drive
Off*/On
Auto Mute
Off/On*
Voice
Off/On*
Language
English*/Spanish
Screen Saver
Off / 1 Minute* / 3 Minute
Smart Power
Off*/On
Display Car Voltage
Off*/On
System Info
Press the SEN button to display system information.
Restore Defaults
Press the SEN button to restore factory default settings
then press SEN button again to confirm (not displayed
until a setting has changed).
Exit Menu
Press the MUTE button to exit the menu.
* = Factory default setting
Detail
In the More detail mode, information about the radar band, signal strength and
frequency will be displayed.
In Less detail mode, only the threat level is displayed (see page 10).
6
English
Nothing Comes Close to a Cobra®
7
Settings
Your Detector
Intro
Operation
Customer
Your Detector
Warranty
Menu - UserAssistance
Settings
continued
Intro
•
AutoMute
AutoMute will automatically reduce the audio volume of all alerts after four
seconds for as long as the signal is detected. The factory setting for AutoMute
is On.
Secondary Icons
Language
The detector can be set to either English or Spanish for all text and voice audio.
Notice
Screen Saver
Your detector has a SCREEN SAVER mode. When SCREEN SAVER is turned On
(factory default is 3 minutes), the screen will change to Dark from it’s Bright,
Dim, or Dimmer setting after the time interval selected. While the screen is Dark,
the scanner will be displayed dimly.
NOTE: While SCREEN SAVER is activated, any alert will turn the display back on
at the last brightness setting (Bright, Dim or Dimmer). Touching any button will
also turn On the display.
Smart Power
Your detector includes the SMARTPOWER feature that, when turned On, will put the
unit into Low Power mode 15 minutes after the car’s engine has been turned Off.
Before SMARTPOWER enters Low Power mode, you will hear three beeps and
SMARTPOWER will flash on the display. To return the unit to Normal Power mode
and exit Low Power mode, start the car, press any button or turn the unit Off and
then On again.
System Info
Displays information about the versions of software/firmware that are
installed on your detector, and the database of Location-Based Alerts (see
page 12).
Operation
Settings
Customer
Warranty
Menu - AlertAssistance
Settings
To change the Alert settings, enter the Menu by pressing the MENU button.
A voice announces “Menu” and the display will change to
Secondary Icons
USER GPS
•
ALERT
Press the SEN button to enter the Alert settings menu.
Press the MUTE or MENU
buttons to switch between the Alert settings.
Notice
Press the DIM
or SEN buttons to change the selected Alert setting’s value.
The value that is shown on the display is the selected value. To exit the menu
simply wait several seconds or select Exit Menu.
RADAR SETTING
VALUE
X Band
Off/On*
K Band
Off/On*
Ka Band
Off/On*
VG-2
Off*/On
Spectre
Off*/On
Laser
On*
Low V. Warning
Off*/On
Exit Menu
Press the MUTE
button to exit the menu.
* = Factory default setting
Low Car Voltage
Displays your car battery voltage and automatically warns you if this drops
below 10.9V. Your detector will then shut off to prevent further draining of
your car battery.
Restore Defaults
To return your detector to factory default settings, press the SEN Button.
Press the SEN Button again to confirm that you want to restore factory
settings. Press the MUTE Button to exit.
8
English
Nothing Comes Close to a Cobra®
9
Understanding Radar
Your Detector
Intro
Operation
Customer
Assistance
Radar Alerts
Your Detector
Warranty
Intro
•
In More detail mode the radar band, signal strength and frequency of the detected
radar signal will be displayed.
Signal Strength
Radar Band
Secondary Icons
Frequency
If you are a new user of radar detectors, you may want to use the Less detail
Notice
mode. In this
mode the display will only show one, two, or three bars which
indicate how likely the alert is to be a police radar or laser gun. This threat level
indication takes into account the laser or radar band, strength, and frequency of
the detected signal.
Level
Display
1
LOW
2
3
Low
Medium
HIGH
High
Understanding Radar and Laser
Radar Speed Monitoring Systems
•
Three band frequencies have been approved by the Federal Communications
Commission (FCC) for use by speed monitoring radar equipment:
X band
K band
Ka band
10.525 GHz
24.150 GHz
33.400 – 36.00 GHz
Your detector detects signals in all three radar bands.
VG-2
VG-2 is a “detector detector” that works by detecting low-level signals emitted
by most radar detectors. Your detector does not emit signals that can be detected
by VG-2, but does detect VG-2 signals and will alert you when a device is in use
near your vehicle.
10
English
Customer
Assistance
Spectre RDD’s
Warranty
Your detector can be spotted by Spectre IV+ RDDs, but is invisible to VG-2 and
Spectre I RDDs. You can choose whether you want to be alerted to VG-2 and
Spectre I & IV+ RDD signals. The factory setting for VG-2 and Spectre I & IV+
Secondary
Icons is Off. It is recommended to leave these Off unless you are concerned
alerts
about being monitored for having a radar detector. For non-commercial
vehicles, radar detectors are legal in the U.S. with the exception of Viginia and
Washington D.C.
Laser Alerts
Notice
With Laser signals you will always receive a full strength alert. In More Detail
mode the word Laser will be shown on the display along with the pulse rate of
the Laser signal. In Less Detail mode three signal strength bars will be shown.
•
LIDAR (Laser)
Threat
MED
Operation
Understanding LIDAR
The correct name for the technology that most people refer to as laser is
actually LIDAR, which stands for Light Detection and Ranging.
LIDAR operates much like radar. Its signal spreads out like a radar signal, though
not as widely. Unlike radar, LIDAR must have a clear line of sight to its target
vehicle throughout the entire measurement interval. Obstructions such as sign
posts, utility poles, tree branches, etc., will prevent valid speed measurement.
Some common questions about LIDAR include:
n D
oes weather have any affect on LIDAR?
Yes. Rain, snow, smoke, fog or airborne dust particles will reduce the
effective range of LIDAR and can, if dense enough, prevent its operation.
n C
an LIDAR operate through glass?
Yes. Newer LIDAR guns can obtain readings through most types of glass.
However, the laser pulse also can be received through glass to trigger an
alarm by your detector.
n C
an LIDAR operate while in motion?
No. Because LIDAR operates by line of sight, the person using it cannot drive
the vehicle, aim and operate the gun all at the same time.
n Is it legal for police to use LIDAR?
Yes, LIDAR is allowed to be used in all 50 States by police. Your detector
detects LIDAR (laser).
Nothing Comes Close to a Cobra®
11
Your Detector
Intro
GPS Settings
Operation
Customer
Assistance
Your Detector
Warranty
Intro
Menu - GPS Settings
•
To change GPS settings, enter the menu by pressing the MENU button. A voice
announces “Menu” and the display with change to
USER GPS
ALERT
Secondary Icons
Press the MUTE button to enter the GPS menu.
Press the MUTE or MENU buttons to switch between the GPS settings.
Press the DIM or SEN buttons to change the selected GPS setting’s value.
The value that is shown on the display is the selected value. To exit the menu
simply waitNotice
several seconds or select Exit Menu.
Operation
Customer
Assistance
Specifications
Warranty
•
Band and Frequencies
Band
X Band
K Band
Ka Band
Laser
VG-2
Secondary Icons
Frequencies
10.525
± 0.050
24.125
± 0.125
34.700
± 1.300
910 ± 50 nm
100
11.500
± 0.250
GHz
GHz
GHz
PPS
GHz
Notice
WARNING Modifications or parts substitutions not approved by
Cobra Electronics Corporation may violate FCC Rules and void your
authority to operate this equipment.
GPS SETTING
VALUE
Speed Units
MPH*/KPH
Speed Mute
Off*/10/15/20...65
Speed Alert
Off*/40/45/50...95
Speed Camera
On*/Off
Red Light Camera
On*/Off
Caution Area
On*/Off
Speed Trap
On*/Off
Lock Out
On*/Off
User Location
On*/Off
Delete User Location
Delete All User Locations
Maintenance
Lock Out Delete
Delete All Locked Out Locations
Your detector is designed and built to give you years of trouble-free performance
without the need for service. No routine Maintenance is required.
If your unit does not appear to be operating properly, please follow these
troubleshooting steps:
n Make sure the power cord is properly connected.
n M
ake sure the socket of your vehicle’s cigarette lighter is clean and free
of corrosion.
n M
ake sure the power cord’s cigarette lighter adapter is firmly seated in
your cigarette lighter.
U.S. Patent Number: 6,078,279
LBAs and Software Updates
Your detector is equipped with an internal GPS receiver to alert you to known
speed trap as well as red-light/speed camera locations. Refer to below LBA
icons for details.
LBA Types
AURA
LBA Types
Photo Enforcement Area
Speed Trap
Speed Camera
Caution Area
Red Light Camera
User Location
English
•
The known speed trap and red-light/speed camera locations (LBAs) data as
well as your detection software can be updated via the micro-USB port on your
detector. To update, connect your detector to a Windows®-based PC and go to
http://www.cobra.com/softwareupdates and select RAD500G to download the
latest data and/or software.
Location-Based Alerts (LBAs)
12
Specifications &
Maintenance
Live Police
AURA
•
•
Nothing Comes Close to a Cobra®
13
Your Detector
Intro
Operation
Warranty
Customer
Assistance
Warranty
Limited 1-Year Warranty
Customer Information
Intro
•
Cobra Electronics Corporation warrants that this product and the component parts
thereof, will be free of defects in workmanship and materials for a period of one year
from the date of first consumer purchase. This warranty may be enforced by the first
Secondary Icons
consumer purchaser. If the product is under warranty, it will be repaired or exchanged
depending on the model as determined at Cobra’s sole discretion. Such remedy shall
be your sole and exclusive remedy for any breach of warranty.
The procedure for obtaining service and support, and the applicability of this warranty,
will vary depending
on the country or jurisdiction in which you purchased and utilize
Notice
the product. For the details on obtaining product service, support and warranty please
visit www.cobra.com/support
Provided that the product is utilized within the U.S.A.- Cobra will, without charge,
repair or replace, at its option, defective products, products or component parts upon
delivery to the Cobra Factory Service department, accompanied by proof of the date of
first consumer purchase, such as a duplicated copy of a sales receipt. You must pay
any initial shipping charges required to ship the product for warranty service, but the
return charges, to an address in the U.S.A., will be at Cobra’s expense, if the product is
repaired or replaced under warranty.
Secondary Icons
Operation
Product Service & Support
and Optional Accessories
Customer
Assistance
Warranty
Product Service and Support
For products purchased in the U.S.A. you may also call 1-773-889-3087.
For Products Purchased in the U.S.A., if your product should require factory service, please
go to www.cobra.com/support and follow the instructions for returning your product to
the Cobra Factory Service Department for service.
Notice
Optional Accessories
You can find quality Cobra products and accessories at your local Cobra dealer,
or in the U.S.A., you can order directly from Cobra at www.cobra.com
Windshield
Mounting Bracket
Straight 12V DC
Power Cord
Coiled 12V DC
Power Cord
Straight Combination Radar
USB Cord
Includes suction cups
Includes plug and fuse
Exclusions: This limited warranty does not apply: 1) To any product damaged by
accident; 2) In the event of misuse, ordinary wear, failure to follow directions, or
improper maintenance of the product or as a result of unauthorized alterations or
repairs; 3) If the serial number has been altered, defaced, or removed; 4) If the product
was purchased or is utilized in a jurisdiction not covered by the limited warranty.
Item #545-159-N-001
Item #420-030-N-001
Includes plug and fuse
Item # 420-026-N-001
Includes plug and USB
Output
Item # PWR USB-01
All implied warranties, including warranties of merchantability and fitness for a
particular purpose are limited in duration to the length of this warranty. Cobra shall
not be liable for any incidental, consequential or other damages; including, without
limitation, damages resulting from loss of use or cost of installation.
Dual Port Power Adapter
This warranty gives you specific legal rights, and you may also have other rights which
may vary from state to state and country to country.
•
For any questions about operating or installing this new Cobra product, PLEASE CONTACT
COBRA FIRST…do not return this product to the retail store. The contact information for
Cobra will vary depending on the country in which you purchased and utilize the product.
For the latest contact information, please go to www.cobra.com/support
Includes adjustable plug
(up to 90˚) and fuse
Item # CLP-2B
Hardwire Cord for Radar
Includes fuse
Item # RA-PSCB
•
Install Mount
Includes 3M Dual Lock™
Item # 545-002
Some states and countries do not allow limitations on how long an implied warranty
lasts and/or do not allow the exclusion or limitation of incidental or consequential
damages, so the above limitations may not apply to you. This warranty gives you
specific legal rights, and you may also have other rights which vary from state to state
and country to country.
14
English
Nothing Comes Close to a Cobra®
15
Customer Information
ntro
Operation
Customer
Assistance
FCC Statement &
Trademark Acknowledgement
NOTES
Warranty
FCC Statement
•
FCC NOTICE: This device complies with part 15 of FCC rules: Operation is subject to the following two
conditions: (1) This device may not cause harmful interference, and (2) This device must accept any
interference received including interference that may cause undesired operation.
NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device,
pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against
harmful interference in a residential installation. This equipment generates uses and can radiate radio
frequency energy and, if not installed and used in accordance with the instructions, may cause harmful
interference to radio communications. However, there is no guarantee that interference will not occur in a
particular installation. If this equipment does cause harmful interference to radio or television reception,
which can be determined by turning the equipment off and on, the user is encouraged to try to correct the
Notice
interference by one or more of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help.
Icons
AVIS FCC: Cet appareil est conforme à la partie 15 des règles de la FCC: Son fonctionnement est soumis aux deux
conditions suivantes: (1) Ce dispositif ne peut causer des interférences nuisibles, et (2) Cet appareil doit accepter
toute interférence reçue, y compris les interférences qui peuvent causer un mauvais fonctionnement.
NOTE: Cet équipement a été testé et jugé conforme aux limites d’un appareil numérique de classe B,
conformément à la partie 15 des règles de la FCC. Ces limites sont conçues pour fournir une protection
raisonnable contre les interférences nuisibles dans une installation résidentielle. Cet équipement
génère, utilise et peut émettre de l’énergie radiofréquence et, si non installé et utilisé conformément aux
instructions, il peut causer des interférences nuisibles aux communications radio. Cependant, il n’y a
aucune garantie que l’interférence ne se produira pas dans une installation particulière. Si cet appareil
provoque des interférences nuisibles à la réception radio ou de télévision, ce qui peut être déterminé
en mettant l’appareil hors tension, l’utilisateur est invité à essayer de corriger l’interférence par une ou
plusieurs des mesures suivantes:
- Réorienter ou déplacer l’antenne de réception.
- Augmenter la distance entre l’équipement et le récepteur.
- Branchez l’appareil dans une prise sur un circuit différent de celui auquel le récepteur est connecté.
- Consulter le revendeur ou un technicien radio / TV expérimenté.
Trademark Acknowledgement
•
Cobra®, DigiView®, EasySet®, Extra Sensory Detection®, LaserEye®, Nothing Comes Close to a Cobra®,
VG-2 Alert®, Xtreme Range Superheterodyne® and the snake design are registered trademarks of Cobra
Electronics Corporation, USA.
Cobra Electronics Corporation™, AURA™, IntelliLink™, IntelliScope™, IntelliView™, Revolution™ Series, IVT
Filter™, SmartPower™, Super-Xtreme Range Superheterodyne™, S-XRS™, and Voice Alert™ are trademarks
of Cobra Electronics Corporation, USA.
Instaclear® for Ford is a registered trademark of Ford Motor Company, Inc. Electriclear® for GM is a
registered trademark of General Motors Corporation. LTI Laser™ and LTI 20-20™ are trademarks of Laser
Technology, Inc. Kustom Laser™, Kustom Laser 340™ and ProLaser II™ are trademarks of Kustom Signals,
Inc. SpeedLaser™ is a trademark of Laser Atlanta. Stalker™ LIDAR is a trademark of Applied Concepts, Inc.
Spectre I™ and Spectre IV™ are trademarks of Stealth Micro Systems Pty. Ltd. SpeedLaser™ is a trademark
of Laser Atlanta, LLC. Interceptor VG-2™ is a trademark of TechniSonic Industries LTD.
16
English
Nothing Comes Close to a Cobra®
17
Download PDF
Similar pages