AUDIO/VIDEO CONTROL RECEIVER
RX-5022VSL
RX-5022V
FM/AM TUNING
PTY–PTY SEARCH–PTY
FM/AM PRESET
UP
UP
DOWN
DOWN
AUDIO/VIDEO CONTROL RECEIVER
FM MODE
STANDBY
MASTER VOLUME
MEMORY
STANDBY/ON
SURROUND ON/OFF
FM MODE
INPUT ANALOG
DVD
VCR
TV SOUND
CD
TAPE/CDR
FM/AM
INPUT DIGITAL
ADJUST SETTING
INPUT ATT
SURROUND MODE
CONTROL
DOWN
UP
SPEAKERS ON/OFF
SOURCE NAME
PHONES
INSTRUCTIONS
For Customer Use:
Enter below the Model No. and Serial
No. which are located either on the rear,
bottom or side of the cabinet. Retain this
information for future reference.
Model No.
Serial No.
LVT0850-007A
[A]
RX-5022VSL[A]_COVER_f
1
02.3.25, 9:35 AM
Warnings, Cautions and Others
switch!
Caution ––
Disconnect the mains plug to shut the power off completely.
switch in any position does not disconnect the mains
The
line. The power can be remote controlled.
CAUTION
To reduce the risk of electrical shocks, fire, etc.:
1. Do not remove screws, covers or cabinet.
2. Do not expose this appliance to rain or moisture.
CAUTION
• Do not block the ventilation openings or holes.
(If the ventilation openings or holes are blocked by a
newspaper or cloth, etc., the heat may not be able to get
out.)
• Do not place any naked flame sources, such as lighted
candles, on the apparatus.
• When discarding batteries, environmental problems must
be considered and local rules or laws governing the
disposal of these batteries must be followed strictly.
• Do not expose this apparatus to rain, moisture, dripping
or splashing and that no objects filled with liquids such as
vases, shall be placed on the apparatus.
G-1
RX-5022VSL[A]Safety_f
1
02.3.25, 9:34 AM
Caution: Proper Ventilation
To avoid risk of electric shock and fire and to protect from
damage.
Locate the apparatus as follows:
Front:
No obstructions open spacing.
Sides:
No obstructions in 10 cm from the sides.
Top:
No obstructions in 10 cm from the top.
Back:
No obstructions in 15 cm from the back
Bottom:
No obstructions, place on the level surface.
In addition, maintain the best possible air circulation as illustrated.
Spacing 15 cm or more
RX-5022VSL
Wall or obstructions
Front
Stand height 15 cm or more
Floor
G-2
RX-5022VSL[A]Safety_f
2
02.3.25, 9:34 AM
Table of Contents
Parts Identification ...................................... 2
Getting Started ........................................... 3
Before Installation ...................................................................... 3
Checking the Supplied Accessories ........................................... 3
Putting Batteries in the Remote Control .................................... 3
Connecting the FM and AM Antennas ....................................... 4
Connecting the Speakers ............................................................ 5
Connecting Audio/Video Components ....................................... 6
Connecting the Power Cord ....................................................... 7
Basic Operations ......................................... 8
Turning On the Power ................................................................ 8
Selecting the Source to Play ....................................................... 8
Adjusting the Volume ................................................................. 9
Listening Only with Headphones ............................................... 9
Turning Off the Sounds Temporarily—Muting ........................ 10
Turning Off the Power with the Sleep Timer ........................... 10
Basic Settings ........................................... 11
Setting the Digital Input (DIGITAL IN) Terminals ................. 11
Selecting the Analog or Digital Input Mode ............................ 11
Setting the Speaker Information ............................................... 12
Sound Adjustments .................................... 15
Attenuating the Input Signal .................................................... 15
Adjusting the Front Speakers Output Balance ......................... 15
Adjusting the Tone ................................................................... 15
Adjusting the Subwoofer Output Level .................................... 15
Tuner Operations ....................................... 16
Tuning in Stations Manually .................................................... 16
Using Preset Tuning ................................................................. 16
Selecting the FM Reception Mode ........................................... 17
Creating Realistic Sound Fields ................... 18
About Relations between Speaker Layout and
Surround Modes ................................................................. 20
Using Dolby Pro Logic II, Dolby Digital and
DTS Digital Surround ........................................................ 21
Using DAP Modes and All Channel Stereo ............................. 23
COMPU LINK Remote Control System ......... 24
Operating JVC's Audio/Video
Components .......................................... 25
Operating Audio Components .................................................. 25
Operating Video Components .................................................. 27
Troubleshooting ......................................... 28
Specifications ............................................ 29
Remote
ONLY
This mark indicates that the remote control CAN
ONLY be used for the operation explained.
Remote
NOT
This mark indicates that the remote control CANNOT
be used for the operation explained. Use buttons on
the front panel.
1
EN01-07.RX-5022VSL[A]_f
1
02.3.25, 9:30 AM
Parts Identification
Table of Contents / Parts Identification
Front Panel
2
3
FM/AM TUNING
FM/AM PRESET
1
45
7 89
6
p
RX-5022V AUDIO/VIDEO CONTROL RECEIVER
UP
UP
DOWN
DOWN
FM MODE
ANALOG
DIGITAL AUTO
LINEAR PCM
DIGITAL
STANDBY
MEMORY
TUNED STEREO
SPK
L
C
S
VOLUME
MASTER VOLUME
RS
CH-
STANDBY/ON
DVD
SURROUND ON/OFF
AUTO MUTING SLEEP
PRO LOGIC ΙΙ DSP H.PHONE INPUT ATT
R
S.WFR LFE
LS
INPUT ANALOG
VCR
TV SOUND
INPUT DIGITAL
ADJUST SETTING
INPUT ATT
CD
SURROUND MODE
TAPE/CDR
FM/AM
CONTROL
DOWN
UP
SPEAKERS ON/OFF
SOURCE NAME
PHONES
q
w e
r t y
u
i
o
See pages in the parentheses for details.
Remote Control
A/V CONTROL
RECEIVER
STANDBY/ON
CENTER
AUDIO
TEST
1
1
3
2
EFFECT
REAR L
4
REAR R
7/P
8
ENTER
0
9
DVD
SLEEP
SOUND
q
REW
FF
REC PAUSE
CD–DISC
w
4
TAPE/CDR
CD
DVD
FM/AM
TV SOUND
VCR
ANALOG
/DIGITAL
e
FM MODE
6
ON/OFF
TV/VIDEO SURROUND
7
8
9
MUTING
MODE
VCR CH
TV CH
r
t
y
u
TV VOLUME
VOLUME
REMOTE CONTROL RM - SRX5022U
y
u
i
o
3
5
1
2
3
4
5
6
7
8
9
p
q
w
e
r
t
10
100
RETURN
p
VCR
SUBWOOFER
10
2
TV
6
5
MENU
Front Panel
STANDBY/ON
button and STANDBY lamp (8)
FM/AM TUNING UP/ DOWN buttons (16)
FM/AM PRESET UP/ DOWN buttons (16, 17)
FM MODE button (17)
MEMORY button (16, 17)
Display (8)
ADJUST button (15, 22, 23)
Remote sensor (3)
SETTING button (11 – 14)
MASTER VOLUME control (9)
PHONES jack (9)
SURROUND ON/OFF button (20, 22, 23)
SURROUND MODE button (20, 22, 23)
SPEAKERS ON/OFF button (9)
• INPUT ANALOG button (11)
• INPUT ATT button (15)
INPUT DIGITAL button (11, 12)
Source selecting buttons (8, 9, 11, 16, 17)
DVD, VCR, TV SOUND, CD, TAPE/CDR, FM/AM
SOURCE NAME button (8)
CONTROL UP5/DOWN∞ buttons
Remote Control
1 • 10 keys for selecting preset channels (17)
• 10 keys for adjusting sound (15, 22, 23)
• 10 keys for operating audio/video components (25 – 27)
2 SOUND button (15, 22, 23)
3 Operating buttons for audio/video components
(25 – 27)
4 REC PAUSE button (26, 27)
5 Source selecting buttons (8, 9, 11, 16, 17, 25 – 27)
TAPE/CDR, CD, DVD, FM/AM, TV SOUND, VCR
6 FM MODE button (17)
7 TV/VIDEO button (27)
8 TV CH (channel) +/– buttons (27)
9 VCR CH (channel) +/– buttons (27)
p STANDBY/ON
buttons (8, 27)
AUDIO, TV, VCR, DVD
q SLEEP button (10)
w CD–DISC button (26)
e ANALOG/DIGITAL button (11, 12)
r SURROUND ON/OFF and SURROUND MODE buttons
(20, 21, 23, 25)
t MUTING button (10)
y TV VOLUME +/– buttons (27)
u VOLUME +/– button (9)
2
EN01-07.RX-5022VSL[A]_f
2
02.3.25, 9:30 AM
Getting Started
Before Installation
General Precautions
• DO NOT insert any metal object into the unit.
• DO NOT disassemble the unit or remove screws, covers, or
cabinet.
• DO NOT expose the unit to rain or moisture.
Putting Batteries in the Remote Control
Before using the remote control, put two supplied batteries first.
• When using the remote control, aim the remote control directly at
the remote sensor on the unit.
1 On the back of the remote control, remove the
battery cover.
Locations
• Install the unit in a location that is level and protected from
moisture.
• The temperature around the unit must be between –5˚C and 35˚C
(23˚F and 95˚F).
• Make sure there is good ventilation around the unit. Poor
ventilation could cause overheating and damage the unit.
Handling the unit
• DO NOT touch the power cord with wet hands.
• DO NOT pull on the power cord to unplug the cord. When
unplugging the cord, always grasp the plug so as not to damage
the cord.
• Keep the power cord away from the connecting cords and the
antenna. The power cord may cause noise or screen interference. It
is recommended to use a coaxial cable for antenna connection,
since it is well-shielded against interference.
• When a power failure occurs, or when you unplug the power cord,
the preset settings such as preset FM/AM channels and sound
adjustments may be erased in a few days.
2 Insert batteries.
• Make sure to match the polarity: (+) to (+) and (–) to (–).
Checking the Supplied Accessories
Check to be sure you have all of the following supplied accessories.
The number in the parentheses indicates the quantity of the pieces
supplied.
3 Replace the cover.
• Remote Control (1)
• Batteries (2)
• AM Loop Antenna (1)
• FM Antenna (1)
If anything is missing, contact your dealer immediately.
If the range or effectiveness of the remote control decreases, replace
the batteries. Use two R6P(SUM-3)/AA(15F) type dry-cell batteries.
CAUTION:
Follow these precautions to avoid leaking or cracking cells:
• Place batteries in the remote control so they match the polarity:
(+) to (+) and (–) to (–).
• Use the correct type of batteries. Batteries that look similar may
differ in voltage.
• Always replace both batteries at the same time.
• Do not expose batteries to heat or flame.
3
EN01-07.RX-5022VSL[A]_f
3
02.3.25, 9:30 AM
AM Loop Antenna
(supplied)
Getting Started
Connecting the FM and AM Antennas
Outdoor FM antenna (not supplied)
If FM reception is poor, connect outdoor FM antenna.
75
FMAXIAL
Supplied FM
antenna
ANTENNA
75
FMAXIAL
or
CO
CO
Standard type
outdoor FM antenna
(not supplied)
FM 75
COAXIAL
FM antenna (supplied)
Extend the supplied FM antenna horizontally.
Snap the tabs on the loop
into the slots of the base
to assemble the AM loop
antenna.
AM
LOOP
AM
EXT
If AM reception is poor, connect outdoor
single vinyl-covered wire (not supplied).
NT
FROKERS
EA LEFT
SP T
RIGH
1
2
NA
TEN FM 75IAL
AN
AX
3
CO
LEFT
T
RIGH
CD
L2
ITA
DIG
( CD
D
DV
) OUT
)
(RECE
TAPR
/CD
L IN
ITA
DIG
DIO
AU
Connect the AM loop antenna supplied to the AM LOOP
terminals.
Turn the loop until you have the best reception.
• If the reception is poor, connect an outdoor single vinylcovered wire (not supplied) to the AM EXT terminal. (Keep the
AM loop antenna connected.)
+
+
–
CE
AN
N : ED
TIO IMP
CAU KER
SPEA
8
–
16
–
–
AM
OP
LO
AM
EXIT
D
DV
T
OU )
(REC
R
VC
INY)
(PLA
EO
VID
T
OU )
(REC
R
VC
AM antenna connection
+
INY)
(PLA
FER
OO
BW
SU OUT
INY)
(PLA
TV
T
RIGH
+
-4
NK
U LI O)
MP HR
CO(SYNC
OR
NIT
MOOUT
L1
ITA )
DIG(DVD
TER
CEN KER
EA
SP
R
REA RS
EAKE
SP LEFT
D
UN
SO
LEFT
T
RIGH DIO
AU
Notes:
• If the AM loop antenna wire is covered with vinyl,
remove the vinyl while twisting it as shown to the
right.
• Make sure the antenna conductors do not touch any
other terminals, connecting cords and power cord.
This could cause poor reception.
FM antenna connection
Connect the supplied FM antenna to the FM 75 Ω COAXIAL
terminal as temporary measure.
Extend the supplied FM antenna horizontally.
• If the reception is poor, connect an outdoor FM antenna (not
supplied). Before attaching a 75 Ω coaxial cable (with a
standard type connector), disconnect the supplied FM antenna.
4
EN01-07.RX-5022VSL[A]_f
4
02.3.25, 9:30 AM
Getting Started
Speaker layout diagram
Connecting the Speakers
After connecting the front, center, rear speakers and/or a subwoofer,
set the speaker setting information properly to obtain the best
possible Surround effect. For details, see pages 12 to 14.
CAUTION:
“NO” for the subwoofer, “LARGE” for the front speakers,
and “SMALL” for the center and rear speakers are initial
settings. To get best possible sound, change the subwoofer
and speaker settings to fit your listening conditions. (See
pages 12 and 13).
Use speakers with the SPEAKER IMPEDANCE indicated by the
speaker terminals.
Center
speaker
Connecting the front, center and rear speakers
1
2
Left front
speaker
3
Subwoofer
Right front
speaker
RX-5022R AUDIO/VIDEO CONTROL RECEIVER
FM/AM TUNING
FM/AM PRESET
UP
UP
DOWN
DOWN
DIMMER
FM MODE
PTY SEARCH
TA/NEWS/INFO
DISPLAY MODE
STANDBY
1
MEMORY
MASTER VOLUME
STANDBY/ON
D I G I T A L
SURROUND
DVD
SURROUND ON/OFF
INPUT ANALOG
VCR
TV SOUND
TAPE/CDR
FM/AM
INPUT DIGITAL
ADJUST SETTING
INPUT ATT
CD
SURROUND MODE
CONTROL
DOWN
UP
SPEAKERS ON/OFF
SOURCE NAME
PHONES
2
Left rear
speaker
For each speaker, connect the (+) and (–) terminals on the rear panel
to the (+) and (–) terminals marked on the speakers.
Right rear
speaker
1 Cut, twist and remove the insulation at the end of
each speaker cord.
2 Open the terminal (1), then insert the speaker
cord (2).
3 Close the terminal.
T
ON
FR ERS
EAK T
SP LEF
+
HT
RIG
NA 75
TEN FM XIAL
AN
TER
CEN ER
EAK
SP
COA
L2
ITA
DIG
( CD
T
LEF
D
DV
) OUT
C)
(RE E
TAPR
/CD
L IN
ITA
DIG
+
–
CE
: EDAN
ION IMP
CAUT ER
SPEAK
8
–
16
–
–
AM
EXIT
AMP
LOO
D
DV
HT
RIG
CD
Connecting the subwoofer speaker
+
+
K-4
U LIN O)
MP HR
CO(SYNC
OR
NIT
MOOUT
L1
ITA
DIG(DVD)
AR
RE ERS
EAK
SP LEFT
HT
RIG
IO
AUD
T
OUC)
(RE
R
VC
IN
AY)
(PL
EO
VID
IN
AY)
(PL
T
OUC)
(RE
R
VC
IN
AY)
(PL
By connecting a subwoofer, you can enhance the bass or reproduce
the original LFE signals recorded in the digital software.
Powered subwoofer
TV
D
UN
HT
SO
RIG
T
LEF
FER
OO
BW
SU OUT
IO
AUD
FER
OO
BW
SU OUT
To
subwoofer
SUBWOOFER
OUT
Connect the input jack of a powered subwoofer to the
SUBWOOFER OUT jack on the rear panel, using a cable with RCA
pin plugs (not supplied).
• Refer also to the manual supplied with your subwoofer.
NT
FROKERS
EA FT
SP T LE
+
H
RIG
TER
CEN KER
EA
SP
R
REAERS
EAK
SP LEFT
HT
+
+
–
CE
AN
N : ED
TIO IMP
CAUAKER
E
SP 16
8
RIG
–
–
To left
front speaker
+
Since bass sound is non-directional, you can place a
subwoofer wherever you like. Normally place it in front of
you.
To left
rear speaker
–
To center speaker
To right front speaker
To right rear speaker
5
EN01-07.RX-5022VSL[A]_f
5
02.3.25, 9:31 AM
Cassette deck or CD recorder
Cassette deck
Turn off all components before connections.
To audio input
Audio Components
• CD player*
• Cassette deck
or CD recorder*
To audio output
PHONO
You can connect the following audio/video components to this
receiver. Refer also to the manuals supplied with your components.
CD
Video Components
• TV*
• VCR
• DVD player*
CD
OUT
(REC)
TAPE
CDR
IN
(PLAY)
* You can connect these components using the methods described in
“Analog connections” (below) or in “Digital connections” (see page 7).
OUT
(REC)
Analog connections
Audio component connections
VCR
IN
(PLAY)
Use the cables with RCA pin plugs (not supplied).
Connect the white plug to the audio left jack, and the red plug to the
audio right jack.
TV SOUND
RIGHT
LEFT
AUDIO
CAUTION:
If you connect a sound-enhancing device such as a graphic equalizer
between the source components and this receiver, the sound output
through this receiver may be distorted.
To audio input
To audio output
CD recorder
Note:
You can connect either a cassette deck or a CD recorder to the TAPE/
CDR jacks. When connecting a CD recorder to the TAPE/CDR jacks,
change the source name to “CDR,” which will be shown on the display
when selected as the source. See page 8 for details.
CD player
CD player
CD
If your audio components have a COMPU LINK jack
See also page 24 for detailed information about the connection and
the COMPU LINK remote control system.
OUT
(REC)
To audio output
TAPE
CDR
IN
(PLAY)
Video component connections
OUT
(REC)
Use the cables with RCA pin plugs (not supplied).
Connect the white plug to the audio left jack, the red plug to the
audio right jack, and the yellow plug to the video jack.
VCR
IN
(PLAY)
TV
TV SOUND
TV
RIGHT
CD
LEFT
AUDIO
OUT
(REC)
MONITOR
OUT
TAPE
CDR
To audio
output
IN
(PLAY)
DVD
OUT
(REC)
OUT
(REC)
VCR
VCR
IN
(PLAY)
IN
(PLAY)
VIDEO
TV SOUND
RIGHT
LEFT
AUDIO
To video input
Connect the TV to the MONITOR OUT jack to view the
playback picture from the other connected video
components.
6
EN01-07.RX-5022VSL[A]_f
6
02.3.25, 9:31 AM
Getting Started
Connecting Audio/Video Components
Getting Started
IMPORTANT:
VCR
VCR
A
C
D
B
CD
OUT
(REC)
MONITOR
OUT
TAPE
CDR
IN
(PLAY)
DVD
OUT
(REC)
OUT
(REC)
VCR
VCR
IN
(PLAY)
• When connecting the DVD player or digital TV using the digital
terminal, you also need to connect it to the video jack on the rear.
Without connecting it to the video jack, you can view no playback
picture.
• After connecting the components using the DIGITAL IN terminals,
set the followings correctly if necessary:
– Set the digital input (DIGITAL IN) terminal setting correctly. For
details, see “Setting the Digital Input (DIGITAL IN) Terminals” on
page 11.
– Select the digital input mode correctly. For details, see “Selecting
the Analog or Digital Input Mode” on page 11.
Digital TV
DVD player
IN
(PLAY)
VIDEO
TV SOUND
CD player
RIGHT
CD recorder
LEFT
AUDIO
Å
ı
Ç
Î
To left/right channel audio output
To left/right channel audio input
To video output
To video input
When the component has a digital
coaxial output terminal, connect it to the
DIGITAL 1 (DVD) terminal, using the
digital coaxial cable (not supplied).
DVD player
DVD player
A
RIGHT
DIGITAL 1
(DVD)
B
Before connecting a digital
optical cable, unplug the
protective plug.
MONITOR
OUT
LEFT
DVD
When the component has a digital
optical output terminal, connect it to the
DIGITAL 2 (CD) terminal, using the
digital optical cable (not supplied).
DIGITAL 2 ( CD )
DIGITAL IN
DVD
AUDIO
OUT
(REC)
VCR
Notes:
IN
(PLAY)
VIDEO
Å To front left/right channel audio output (or to audio mixed
output)
ı To video output
• When shipped from the factory, the DIGITAL IN terminals have
been set for use with the following components.
– DIGITAL 1 (coaxial): For DVD player
– DIGITAL 2 (optical): For CD player
• When you want to operate the CD player or CD recorder using the
COMPU LINK remote control system, connect the target
component also as described in “Analog connections” (see page 6).
Note:
To enjoy the software encoded with Dolby Digital or DTS Digital
Surround, you must connect the DVD player using the digital terminal
on the rear of this receiver. (See “Digital connections” below.)
Connecting the Power Cord
Before plugging the power cord into an AC outlet, make sure that all
connections have been made.
Plug the power cord into an AC outlet.
Digital connections
This receiver is equipped with two DIGITAL IN terminals—one
digital coaxial terminal and one digital optical terminal.
You can connect any component to one of the digital terminals using
a digital coaxial cable (not supplied) or digital optical cable (not
supplied).
CAUTIONS:
• Do not touch the power cord with wet hands.
• Do not pull on the power cord to unplug the cord. When
unplugging the cord, always grasp the plug so as not to damage
the cord.
7
EN01-07.RX-5022VSL[A]_f
7
02.3.25, 9:31 AM
Basic Operations
Remote Control
Display
STANDBY lamp
A/V CONTROL
RECEIVER
STANDBY/ON
CENTER
AUDIO
TEST
1
EFFECT
REAR L
5
4
RX-5022V AUDIO/VIDEO CONTROL RECEIVER
7/P
FM/AM PRESET
UP
FM MODE
8
10
UP
ANALOG
DIGITAL AUTO
LINEAR PCM
DIGITAL
MEMORY
DOWN
DOWN
TUNED STEREO
SPK
L
C
AUTO MUTING SLEEP
S
PRO LOGIC ΙΙ DSP H.PHONE INPUT ATT
R
MASTER VOLUME
VOLUME
9
INPUT ANALOG
PTY–PTY SEARCH–PTY
REW
FF
DVD
VCR
TV SOUND
CD
TAPE/CDR
FM/AM
INPUT DIGITAL
Source
selecting
buttons
ADJUST SETTING
INPUT ATT
SURROUND MODE
SLEEP
SOUND
REC PAUSE
SURROUND ON/OFF
DVD
CONTROL
DOWN
UP
SPEAKERS ON/OFF
TAPE/CDR
CD
DVD
FM/AM
TV SOUND
VCR
ANALOG
/DIGITAL
FM MODE
ON/OFF
SOURCE NAME
TV/VIDEO SURROUND
MUTING
MODE
VCR CH
TV CH
TV VOLUME
VOLUME
Source
SOURCE
selecting NAME
buttons
SPEAKERS
ON/OFF
STANDBY/ON
Turning On the Power
Press STANDBY/ON
remote control).
(or STANDBY/ON
AUDIO on the
STANDBY/ON
STANDBY
AUDIO
STANDBY/ON
From the remote control
The STANDBY lamp goes off. The name of the current source (or
station frequency) appears on the display.
Current source name appears
SPK
L
C
R
VOLUME
S.WFR LFE
LS
S
: Select the DVD player.
: Select the VCR.
: Select the TV sound.
: Select the CD player.
: Select the cassette deck (or the CD recorder).
: Select an FM or AM broadcast.
• Each time you press the button, the band
alternates between FM and AM.
Notes:
On the front panel
ANALOG
MUTING
VOLUME
+/–
REMOTE CONTROL RM - SRX5022U
MASTER
VOLUME
DVD
VCR
TV SOUND
CD *
TAPE/CDR *
FM/AM *
SLEEP
CD–DISC
PHONES
PHONES
jack
STANDBY/
ON
AUDIO
10
100
RS
CH-
STANDBY/ON
0
RETURN
S.WFR LFE
LS
VCR
SUBWOOFER
ENTER
FM/AM TUNING
TV
6
REAR R
MENU
STANDBY
3
2
• When connecting a CD recorder (to the TAPE/CDR jacks), change
the source name that appears on the display. See below for details.
• When you have connected some digital source components using
the digital terminals (see page 7), you need to select the digital
input mode (see page 11).
• When you press one of the source selecting buttons on the remote
control marked above with an asterisk (*), the receiver
automatically turns on.
RS
CH-
Changing the source name
Current volume level is shown here
To turn off the power (into standby mode)
(or
Press STANDBY/ON
AUDIO on the remote
STANDBY/ON
control) again.
The STANDBY lamp on the front panel lights up.
STANDBY
When you connect the CD recorder to the TAPE/
CDR jacks on the rear panel and select the CD
recorder as the source, change the source name
shown on the display.
Remote
NOT
STANDBY/ON
1 Press TAPE/CDR (SOURCE NAME).
TAPE/CDR
• Make sure “TAPE” appears on the display.
Note:
SOURCE NAME
A small amount of power is consumed in standby mode. To turn the
power off completely, unplug the AC power cord.
Selecting the Source to Play
Press one of the source selecting buttons. The selected source name
appears on the display.
DVD
CD
VCR
TAPE/CDR
TV SOUND
TAPE/CDR
CD
DVD
FM/AM
TV SOUND
VCR
FM/AM
SOURCE NAME
On the front panel
From the remote control
2 Press and hold SOURCE NAME
(TAPE/CDR) until “ASSIGN CDR” appears on the display.
To change the source name from “CDR” to “TAPE,” repeat the
same procedure above (in step 1, make sure “CDR” appears on the
display).
Note:
Without changing the source name, you can still use the connected
component. However, there may be some inconvenience.
– “TAPE” will appear on the display when you select the CD
recorder.
– You cannot use the digital input (see page 11) for the CD recorder.
– You cannot use the COMPU LINK remote control system (see page
24) to operate the CD recorder.
8
EN08-17.RX-5022VSL[A]_f
8
02.3.25, 9:31 AM
Getting Started / Basic Operation
Front Panel
Basic Operations
Selecting different sources for picture and
sound
You can watch picture from a video component while listening to
sound from another component.
Listening Only with Headphones
You must turn off the speakers when you listen with headphones.
1 Connect a pair of headphones to the PHONES jack on the front
Press one of the audio source selecting buttons (CD, TAPE/CDR,
FM/AM), while viewing the picture from a video component such as
the VCR or DVD player, etc.
DVD
VCR
TV SOUND
CD
TAPE/CDR
FM/AM
TAPE/CDR
CD
DVD
FM/AM
TV SOUND
VCR
panel.
2 Press SPEAKERS ON/OFF.
• “HEADPHONE” appears for a while and the H. PHONE
indicator lights up on the display.
The H. PHONE indicator lights up.
ANALOG
SOURCE NAME
L
On the front panel
R
H.PHONE
From the remote control
Note:
Once you have selected a video source, pictures of the selected
source are sent to the TV until you select another video source.
Adjusting the Volume
On the front panel:
MASTER VOLUME
To increase the volume, turn MASTER
VOLUME clockwise.
To decrease the volume, turn it
counterclockwise.
From the remote control:
This cancels the Surround mode currently selected, and activates
the HEADPHONE mode.
HEADPHONE mode
When using the headphones, following signals are output
regardless of your speaker setting:
— For 2 channel sources, the front left and right channel signals
are output directly from the headphones.
— For multichannel sources, the front left and right, center, and
rear channel signals are down-mixed and then output from the
headphones.
You can enjoy multichannel sound sources using the
headphones.
To increase the volume, press VOLUME +.
To decrease the volume, press VOLUME –.
VOLUME
CAUTION:
Always set the volume to the minimum before starting any source. If
the volume is set at its high level, the sudden blast of sound energy
can permanently damage your hearing and/or ruin your speakers.
CAUTION:
Be sure to turn down the volume:
• Before connecting or putting on headphones, as high volume can
damage both the headphones and your hearing.
• Before turning on speakers again, as high volume may output from
the speakers.
Note:
The volume level can be adjusted within the range of “0” (minimum) to
“50” (maximum).
9
EN08-17.RX-5022VSL[A]_f
9
02.3.25, 9:31 AM
Remote
ONLY
Press MUTING on the remote control to mute
the sound through all speakers and headphones
connected.
• “MUTING” appears on the display and the volume
turns off (the volume level indicator goes off).
MUTING
L
C
R
S.WFR LFE
S
LS
This receiver memorizes sound settings for each source when:
• you turn off the power,
• you change the source, and
• you assign the source name.
When you change the source, the memorized settings for the
newly selected source are automatically recalled.
The following can be stored for each source:
• Input attenuator mode (see page 15)
• Balance (see page 15)
• Tone adjustment (see page 15)
• Subwoofer output level (see page 15)
• Surround mode selection (see pages 21 – 23 )
SPK
ANALOG
Basic adjustment auto memory
RS
CH-
Notes:
To restore the sound, press MUTING again.
• Turning MASTER VOLUME on the front panel or pressing
VOLUME +/– on the remote control also restores the sound.
• You cannot assign and store different settings for digital input
mode and analog input mode.
• If the source is FM or AM, you can assign a different setting for
each band.
For recording
Turning Off the Power
with the Sleep Timer
Remote
ONLY
You can fall asleep while listening to music—Sleep Timer.
Press SLEEP on the remote control repeatedly.
• The SLEEP indicator lights up on the display, and the
shut-off time changes in 10 minutes intervals.
ANALOG
SPK
L
C
SLEEP
SLEEP
You can record any sources playing through the receiver to a
cassette deck (or a CD recorder) connected to the TAPE/CDR
jacks and the VCR connected to the VCR jacks at the same time.
While recording, you can listen to the selected sound source at
whatever sound level you like without affecting the sound levels
of the recording.
Note:
The output volume level, tone adjustment (see page 15), and
Surround modes (see page 18) cannot affect the recording.
R
S.WFR LFE
LS
S
RS
Signal and speaker indicators on the display
CH-
10
20
30
40
50
60
0 (Canceled)
90
80
70
L
C
R
S.WFR LFE
LS
When the shut-off time comes
The receiver turns off automatically.
To check or change the time remaining until the shut-off time
Press SLEEP once.
The remaining time (in minutes) until the shut-off time appears.
• To change the shut-off time, press SLEEP repeatedly.
To cancel the Sleep Timer
Press SLEEP repeatedly until “SLEEP 0 MIN” appears on the
display. (The SLEEP indicator goes off.)
• Turning off the power also cancels the Sleep Timer.
Speaker indicators
Signal indicators
S
ANALOG
DIGITAL AUTO
LINEAR PCM
DIGITAL
RS
SPK
L
C
ONETOUCH
R
PRO LOGIC ΙΙ
L
C
R
S.WFR LFE
LS
S
RS
CH-
S.WFR LFE
LS
S
RS
The following signal indicators light up—:
L : •When digital input is selected: Lights up when the left
channel signal comes in.
• When analog input is selected: Always lights up.
R : • When digital input is selected: Lights up when the right
channel signal comes in.
• When analog input is selected: Always lights up.
C : When the center channel signal comes in.
LS : When the left rear channel signal comes in.
RS : When the right rear channel signal comes in.
S : When the monaural rear channel signal or 2 channel Dolby
Surround encoded signal comes in.
LFE: When the LFE channel signal comes in.
The speaker indicators light up when both of the following
conditions satisfied:
• The corresponding speaker is activated, and
• The corresponding speaker is required for the current playback.
Note:
When “SUBWOOFER” is set to “YES” (see page 12),
up.
S.WFR
lights
10
EN08-17.RX-5022VSL[A]_f
10
02.3.25, 9:31 AM
Basic Operation
Turning Off the Sounds
Temporarily—Muting
Basic Settings
Front Panel
Remote Control
Display
A/V CONTROL
RECEIVER
STANDBY/ON
CENTER
AUDIO
TEST
1
EFFECT
REAR L
4
RX-5022V AUDIO/VIDEO CONTROL RECEIVER
FM/AM PRESET
UP
UP
DOWN
DOWN
MEMORY
TUNED STEREO
SPK
L
C
AUTO MUTING SLEEP
PRO LOGIC ΙΙ DSP H.PHONE INPUT ATT
R
DVD
10
0
RETURN
RS
S
SUBWOOFER
10
MASTER VOLUME
VOLUME
S.WFR LFE
LS
VCR
9
8
ENTER
ANALOG
DIGITAL AUTO
LINEAR PCM
DIGITAL
STANDBY
100
SLEEP
SOUND
CH-
STANDBY/ON
TV
REAR R
7/P
FM MODE
6
5
MENU
FM/AM TUNING
3
2
PTY–PTY SEARCH–PTY
REW
FF
DVD
SURROUND ON/OFF
INPUT ANALOG
VCR
REC PAUSE
TV SOUND
INPUT DIGITAL
Source
selecting
buttons
ADJUST SETTING
INPUT ATT
CD
SURROUND MODE
TAPE/CDR
FM/AM
CONTROL
DOWN
UP
SPEAKERS ON/OFF
SOURCE NAME
CD–DISC
TAPE/CDR
CD
DVD
FM/AM
TV SOUND
VCR
ANALOG/
DIGITAL
ANALOG
/DIGITAL
FM MODE
ON/OFF
TV/VIDEO SURROUND
PHONES
MUTING
MODE
VCR CH
TV CH
TV VOLUME
VOLUME
INPUT
ANALOG
INPUT
DIGITAL
SETTING
Source
selecting
buttons
REMOTE CONTROL RM - SRX5022U
CONTROL
UP 5/DOWN ∞
Setting the Digital Input
[DIGITAL IN] Terminals
Remote
NOT
Selecting the Analog or Digital Input
Mode
When you use the digital input terminals, register what components
are connected to which terminals (DIGITAL 1/2) so that the correct
source name will appear when you select the digital source.
When you have connected digital source components using both the
analog connection (see page 6) and the digital connection (see page
7) methods, you need to select the input mode correctly.
Before you start, remember...
There is a time limit in doing the following steps. If the setting is
canceled before you finish, start from step 1 again.
1
1
Press SETTING repeatedly until
“DIGITAL IN” appears on the display.
SETTING
The display changes to show the current setting.
Press one of the source selecting buttons—DVD,
TV SOUND, CD, or TAPE/CDR*—for which you
want to change the input mode.
DVD
VCR
TV SOUND
CD
TAPE/CDR
FM/AM
DIGITAL 2 terminal setting
TAPE/CDR
CD
DVD
FM/AM
TV SOUND
VCR
SOURCE NAME
S.WFR LFE
LS
S
On the front panel
RS
CH-
From the remote control
Note:
DIGITAL 1 terminal setting
* Among the sources listed above, you can select the digital input
only for the sources which you have selected the digital input
terminals for. (See “Setting the Digital Input (DIGITAL IN)
Terminals.”)
* “1DVD 2CD” is the initial setting. If you have already
changed the setting, another combination will be shown.
2
Press CONTROL UP 5/DOWN ∞ to
select the appropriate digital terminal
setting.
CONTROL
DOWN
UP
• Each time you press the button, the display
changes to show the following:
1 DVD 2 CD j 1 DVD 2 TV j
1 CD 2 DVD j 1 CD 2 TV j
1 TV 2 DVD j 1 TV 2 CD j
1 CDR 2 DVD j 1 CDR 2 CD j
(back to the beginning)
1 DVD 2 CDR j
1 CD 2 CDR j
1 TV 2 CDR j
1 CDR 2 TV j
2
Select digital input mode.
On the front panel:
Press INPUT DIGITAL.
INPUT DIGITAL
“DIGITAL AUTO” appears on the display
and the indicator for the detected signals also
lights up.
To change the input mode back to analog
input, press INPUT ANALOG.
“ANALOG” appears on the display for a
while.
INPUT ANALOG
INPUT ATT
From the remote control:
Note:
When shipped from the factory, the DIGITAL IN terminals can be used
as the digital input for the following components.
– DIGITAL 1 (coaxial): For DVD player
– DIGITAL 2 (optical): For CD player
Press ANALOG/DIGITAL.
ANALOG
/DIGITAL
• Each time you press the button, the input mode
alternates between the analog input (“ANALOG”)
and the digital input (“DIGITAL AUTO”).
TO BE CONTINUED TO THE NEXT PAGE
11
EN08-17.RX-5022VSL[A]_f
11
02.3.25, 9:31 AM
ANALOG
: Select this for the analog input mode.
(Initial setting when shipped from the
factory.)
If the following symptoms occur while playing Dolby Digital or
DTS Digital Surround software with “DIGITAL AUTO”
selected, follow the procedure below.
• Sound does not come out at the beginning of playback.
• Noise comes out while searching or skipping chapters or tracks.
1 Press INPUT DIGITAL (or ANALOG/DIGITAL on the remote
control).
• “DIGITAL AUTO” appears on the display.
Remote
NOT
Setting the Speaker Information
To obtain the best possible sound or effect from the Surround modes
(see page 18), register the following speakers and subwoofer
information after all connections are completed.
The followings are items you can set:
• Subwoofer information—SUBWOOFER
• Speaker size—FRNT SP, CNTR SP, REAR SP
• Speaker distance—UNIT, FRNT DIS, CNTR DIS, REAR DIS
• Crossover frequency—CROSS
• Low frequency effect attenuator—LFE ATT
• Dynamic range compression—D. COMP
Before you start, remember...
There is a time limit in doing the following steps. If the setting is
canceled before you finish, start from step 1 again.
2 Press CONTROL UP 5/DOWN ∞ to select
Remote
“DOLBY DIGITAL” or “DTS SURROUND”
NOT
while “DIGITAL AUTO” still remains on the
display.
• Each time you press the button, the digital input mode
changes as follows:
When “DOLBY DIGITAL” or “DTS SURROUND”
is selected, “DIGITAL AUTO” goes off.
SPK
DIGITAL AUTO
L
C
LS
S
Subwoofer information
Register whether you have connected a subwoofer or not.
R
S.WFR LFE
DIGITAL
“NO” for the subwoofer, “LARGE” for the front speakers,
and “SMALL” for the center and rear speakers are initial
settings. To get best possible sound, change the subwoofer
and speaker settings to fit your listening conditions.
RS
CH-
DIGITAL AUTO
1
Press SETTING repeatedly until
“SUBWOOFER” (with the current
setting) appears on the display.
2
Press CONTROL UP 5/DOWN ∞ to
register whether you have connected a
subwoofer or not.
DTS SURROUND
DOLBY DIGITAL
• To play back software encoded with Dolby Digital, select
“DOLBY DIGITAL.”
• To play back software encoded with DTS Digital Surround,
select “DTS SURROUND.”
Note:
When you turn off the power or select another source, “DOLBY
DIGITAL” and “DTS SURROUND” are canceled and the digital input
mode is automatically reset to “DIGITAL AUTO.”
The followings are the analog/digital signal indicators on the display
to indicate what type of the signal comes into the receiver.
T SETTING
CONTROL
DOWN
UP
• Each time you press the button, the subwoofer
setting alternates between “YES” and “NO.”
YES
: Select this when you have connected a subwoofer.
You can adjust the subwoofer output level
(see page 15).
NO
: Select this when you have not connected or have
disconnected a subwoofer.
ANALOG
: Lights when the analog input is selected.
LINEAR PCM : Lights when Linear PCM signals come in.
DIGITAL : • Lights when Dolby Digital signals come in.
• Flashes when “DOLBY DIGITAL” is
selected for software not encoded with
Dolby Digital signals.
: • Lights when DTS signals come in.
• Flashes when “DTS SURROUND” is
selected for software not encoded with DTS
signals.
Note:
When “DIGITAL AUTO” cannot recognize the incoming signals, no
digital signal indicators light up on the display.
12
EN08-17.RX-5022VSL[A]_f
12
02.3.25, 9:32 AM
Basic Settings
DIGITAL AUTO : Select this for the digital input mode. The
receiver automatically detects the
incoming signal format. (The DIGITAL
AUTO indicator lights up on the display,
then the digital signal indicator for the
detected signals lights up.)
Basic Settings
Speaker size
Speaker distance
Register the sizes of all the connected speakers.
• When you change your speakers, register the information about
the speakers again.
Register the unit you use, then the speaker distance from your
listening point.
• If you have set the unit before, start from step 3.
1
1
2
T SETTING
Press SETTING repeatedly until
“FRNT SP (Front speaker),” “CNTR
SP (Center speaker)” or “REAR SP
(Rear speaker)” (with the current setting)
appears on the display.
Press CONTROL UP 5/DOWN ∞ to
select the appropriate item about the
speaker selected in the above step.
CONTROL
DOWN
UP
Press SETTING repeatedly until
“UNIT” (with the current setting)*
appears on the display.
SETTING
* “METER” is the initial setting. If you have already changed
the setting, “FEET” will be shown.
2
Press CONTROL UP 5/DOWN ∞ to
select the unit.
CONTROL
DOWN
UP
• Each time you press the button, the setting
alternates between “METER” and “FEET.”
• Each time you press the button, the display
changes as follows:
METER : Speaker distance is shown in meter.
SMALL
LARGE
FEET
: Speaker distance is shown in feet.
NONE
3
LARGE : Select this when the speaker size is relatively large.
(See “Notes” below.)
SMALL : Select this when the speaker size is relatively small.
(See “Notes” below.)
NONE
3
The display shows the current setting in the unit selected in step 2.
* “3.0m” is the initial setting for meter and “10FT” is for feet. If
you have already changed the setting, another value will be
shown.
: Select this when you have not connected a speaker.
(Not selectable for the front speakers)
Repeat steps 1 and 2 to select the appropriate
items for other speakers.
Notes:
• Keep the following comment in mind as reference when adjusting.
– If the size of the cone speaker unit built in your speaker is greater
than 12 cm, select “LARGE,” and if it is smaller than 12 cm,
select “SMALL.”
• If you have selected “NO” for the subwoofer setting, you can only
select “LARGE” for the front speaker setting.
• If you have selected “SMALL” for the front speaker setting, you
cannot select “LARGE” for the center and rear speaker settings.
SETTING
Press SETTING repeatedly until
“FRNT DIS (Front distance),” “CNTR
DIS (Center distance)” or “REAR DIS
(Rear distance)” (with the current setting)*
appears on the display.
4
Press CONTROL UP 5/DOWN ∞ to
select the appropriate speaker
distance.
CONTROL
DOWN
UP
• If you have selected “METER” in step 2, the
value is changed from “0.3m” to “9.0m” by 0.3 m step.
• If you have selected “FEET” in step 2, the value is changed
from “1FT” to “30FT” by 1 foot step.
Left front
speaker
Center speaker
Right front
speaker
3.0 m
(10 feet)
2.7 m
(9 feet)
2.4 m
(8 feet)
2.1 m
(7 feet)
Left rear
speaker
Right rear
speaker
Example: In this case,
set “FRNT DIS” to “3.0m” or “10FT,”
set “CNTR DIS” to “2.7m” or “9FT” and,
set “REAR DIS” to “2.4m” or “8FT.”
Note:
If you have selected “NONE” for the center and rear speakers
setting, you cannot set the speaker distance for the center and
rear speakers.
13
EN08-17.RX-5022VSL[A]_f
13
02.3.25, 9:32 AM
Low frequency effect attenuator
Small speakers cannot reproduce the bass sounds efficiently. If you
use a small speaker in any position, this receiver automatically
reallocates the bass sound elements assigned to the small speaker to
the large speakers.
To use this function properly, set this crossover frequency level
according to the size of the small speaker connected.
• If you have selected “LARGE” for all speakers, this function will
not take effect (“CROSS OFF” appears).
If the bass sound is distorted while playing back software using
Dolby Digital or DTS Digital Surround, follow the procedure
below:
• This function takes effect only when the subwoofer (LFE) signals
come in, (with “SUBWOOFER” set to “YES”).
1
Press SETTING repeatedly until
“CROSS (Crossover)” (with the current
setting)* appears on the display.
SETTING
* “100HZ” is the initial setting. If you have already
changed the setting, another frequency will be shown.
2
Press CONTROL UP 5/DOWN ∞ to
select the crossover frequency level
you like to use.
1
100HZ
200HZ
SETTING
* “0dB” is the initial setting. If you have already changed the
setting, “–10dB” will be shown.
2
CONTROL
DOWN
UP
Press CONTROL UP 5/DOWN ∞ to
select the low frequency effect
attenuator level.
CONTROL
DOWN
UP
• Each time you press the button, the setting
alternates between “0dB” and “–10dB.”
• Each time you press the button, the crossover
frequency level changes as follows:
80HZ
Press SETTING repeatedly until “LFE
ATT (Low Frequency Effect
Attenuator)” (with the current setting)*
appears on the display.
0dB
: Normally select this.
–10dB
120HZ
: Select this when the bass sound is distorted.
150HZ
Note:
Crossover frequency is not valid for the HEADPHONE mode.
Dynamic range compression
You can compress the dynamic range (difference between maximum
sound and minimum sound) of the reproduced sound. This is useful
when enjoying surround sound at night.
• This function takes effect only when playing back a source using
Dolby Digital.
1
Press SETTING repeatedly until
“D. COMP (Dynamic range
compression)” (with the current
setting)* appears on the display.
SETTING
* “MID” is the initial setting. If you have already changed the
setting, another setting will be shown.
2
Press CONTROL UP 5/DOWN ∞ to
select the appropriate compression
level.
CONTROL
DOWN
UP
• Each time you press the button, the
display changes as follows:
MID
OFF
MAX
OFF : Select this when you want to enjoy surround with its
full dynamic range. (No effect applied.)
MID
: Select this when you want to reduce the dynamic range
a little.
MAX : Select this when you want to apply the compression
effect fully. (Useful at night.)
14
EN08-17.RX-5022VSL[A]_f
14
02.3.25, 9:32 AM
Basic Settings
Crossover frequency
Sound Adjustments
Remote Control
Front Panel
Display
A/V CONTROL
RECEIVER
STANDBY/ON
CENTER
AUDIO
TEST
1
REAR L
5
4
FM/AM TUNING
FM/AM PRESET
UP
SUBWOOFER +/–
FM MODE
8
DOWN
TUNED STEREO
SPK
L
C
AUTO MUTING SLEEP
PRO LOGIC ΙΙ DSP H.PHONE INPUT ATT
R
10
0
S.WFR LFE
LS
S
RS
DVD
10
100
SLEEP
SOUND
SOUND
MASTER VOLUME
VOLUME
VCR
9
SUBWOOFER
ENTER
RETURN
ANALOG
DIGITAL AUTO
LINEAR PCM
DIGITAL
MEMORY
DOWN
7/P
UP
STANDBY
TV
6
REAR R
MENU
RX-5022V AUDIO/VIDEO CONTROL RECEIVER
3
2
EFFECT
PTY–PTY SEARCH–PTY
REW
FF
CH-
STANDBY/ON
REC PAUSE
DVD
SURROUND ON/OFF
INPUT ANALOG
VCR
TV SOUND
INPUT DIGITAL
CD–DISC
TAPE/CDR
CD
FM/AM
TV SOUND
DVD
ADJUST SETTING
ANALOG
/DIGITAL
VCR
INPUT ATT
CD
SURROUND MODE
TAPE/CDR
FM/AM
FM MODE
CONTROL
DOWN
UP
ON/OFF
SPEAKERS ON/OFF
TV/VIDEO SURROUND
MUTING
MODE
SOURCE NAME
PHONES
VCR CH
TV CH
TV VOLUME
VOLUME
REMOTE CONTROL RM- SRX5022U
INPUT ATT
ADJUST
CONTROL UP 5/DOWN ∞
Once each of following settings has been adjusted, this receiver
memorizes the adjustment for each source.
1
Remote
NOT
Attenuating the Input Signal
Press and hold INPUT ATT (INPUT
ANALOG) so that the INPUT ATT
indicator lights up on the display.
BASS
INPUT ATT
Adjusting the Front Speakers
Output Balance
TREBLE : To adjust the treble (–10 to +10).
2
Before you start, remember...
There is a time limit in doing the following steps. If the setting is
canceled before you finish, start from step 1 again.
Press ADJUST repeatedly until
“BALANCE” (with the current setting)*
appears on the display.
You can adjust the subwoofer output level if you have connected a
subwoofer and set the subwoofer information correctly—“YES.”
On the front panel:
Before you start, remember...
There is a time limit in doing the following steps. If the setting is
canceled before you finish, start from step 1 again.
1
ADJUST SETT
CONTROL
DOWN
UP
• Pressing CONTROL UP 5 decreases the
left channel output from “CNTR” (Center) to
“L–21.”
• Pressing CONTROL DOWN ∞ decreases
the right channel output from “CNTR” (Center) to “R–21.”
Adjusting the Tone
Remote
NOT
You can adjust the bass and treble sounds as you like.
Before you start, remember...
There is a time limit in doing the following steps. If the setting is
canceled before you finish, start from step 1 again.
Press ADJUST repeatedly until
“SUBWFR (Subwoofer)” (with the
current setting)* appears on the
display.
15
ADJUST SETTIN
* “0” is the initial setting. If you have already changed the
setting, another number (level) will be shown.
2
Press CONTROL UP 5/DOWN ∞ to
adjust the subwoofer output level
(–10 to +10).
CONTROL
DOWN
UP
From the remote control:
1
Press SOUND.
SOUND
The 10 keys are activated for sound adjustments.
2
Press SUBWOOFER +/– to adjust
the subwoofer output level
(–10 to +10).
SUBWOOFER
0
10
100
Note:
Subwoofer output level cannot be adjusted when using headphones.
15
EN08-17.RX-5022VSL[A]_f
CONTROL
DOWN
UP
• Each time you press the button, the sound
level changes by ±2 steps.
* “CNTR” (Center) is the initial setting. If you have already
changed the setting, another setting will be shown.
Press CONTROL UP 5/DOWN ∞
to adjust the balance.
Press CONTROL UP 5/DOWN ∞ to
adjust the bass or treble sounds level.
Adjusting the Subwoofer Output Level
Remote
NOT
If the sounds you hear from the front right and left speakers are
unequal, you can adjust the speakers output balance.
2
: To adjust the bass (–10 to +10).
INPUT ANALOG
• Each time you press and hold the button, the Input Attenuator
mode turns on (“INPUT ATT ON”) or off (“INPUT
NORMAL”).
1
ADJUST SETTIN
* “0” is the initial setting. If you have already changed the
setting, another number (level) will be shown.
When the input level of the analog source is too high, the sounds
will be distorted. If this happens, you need to attenuate the input
signal level to prevent the sound distortion.
1
Press ADJUST repeatedly until “BASS”
or “TREBLE” (with the current
setting)* appears on the display.
02.3.25, 9:32 AM
Tuner Operations
Sound Adjustments / Tuner Operations
Front Panel
Remote Control
FM/AM
FM/AM
TUNING
PRESET
UP/DOWN UP/DOWN FM MODE
A/V CONTROL
RECEIVER
STANDBY/ON
CENTER
AUDIO
TEST
1
Display
EFFECT
REAR L
4
10 keys
REAR R
7/P
SUBWOOFER
10
FM/AM PRESET
VCR
9
8
ENTER
UP
TV
6
5
MENU
DVD
10
0
100
RETURN
RX-5022V AUDIO/VIDEO CONTROL RECEIVER
FM/AM TUNING
3
2
SLEEP
SOUND
PTY–PTY SEARCH–PTY
REW
FF
FM MODE
UP
ANALOG
DIGITAL AUTO
LINEAR PCM
DIGITAL
STANDBY
MEMORY
DOWN
DOWN
TUNED STEREO
SPK
L
C
AUTO MUTING SLEEP
PRO LOGIC ΙΙ DSP H.PHONE INPUT ATT
R
MASTER VOLUME
VOLUME
REC PAUSE
CD–DISC
S.WFR LFE
LS
S
RS
CH-
STANDBY/ON
DVD
SURROUND ON/OFF
INPUT ANALOG
VCR
FM/AM
FM MODE
TV SOUND
INPUT DIGITAL
ADJUST SETTING
INPUT ATT
CD
SURROUND MODE
TAPE/CDR
FM/AM
CONTROL
DOWN
UP
TAPE/CDR
CD
DVD
FM/AM
TV SOUND
VCR
ANALOG
/DIGITAL
FM MODE
ON/OFF
TV/VIDEO SURROUND
MUTING
MODE
SPEAKERS ON/OFF
SOURCE NAME
VCR CH
TV CH
TV VOLUME
PHONES
VOLUME
REMOTE CONTROL RM-SRX5022U
MEMORY
FM/AM
Tuning in Stations Manually
1
Using Preset Tuning
Press FM/AM to select the band (FM or AM).
The last received station of the selected band is tuned in.
FM/AM
FM/AM
To store the preset stations
From the remote control
On the front panel
• Each time you press the button, the band alternates between
FM and AM.
ANALOG
TUNED STEREO
SPK
L
C
Once a station is assigned to a channel number, the station can be
quickly tuned. You can preset up to 30 FM and 15 AM stations.
Before you start, remember...
There is a time limit in doing the following steps. If the setting is
canceled before you finish, start from step 2 again.
1
AUTO MUTING
R
VOLUME
S.WFR LFE
LS
S
Ex.: When the FM band is selected.
Press FM/AM TUNING UP/DOWN
until you find the frequency you want.
• Pressing FM/AM TUNING UP increases
the frequency.
• Pressing FM/AM TUNING DOWN
decreases the frequency.
Tune in the station you want to preset
(see “Tuning in Stations Manually”).
• If you want to store the FM reception mode for this station,
select the FM reception mode you want. See “Selecting the
FM Reception Mode” on page 17.
RS
CH-
2
Remote
NOT
ANALOG
TUNED STEREO
SPK
L
Remote
NOT
C
AUTO MUTING
R
VOLUME
S.WFR LFE
LS
RS
S
CH-
FM/AM TUNING
UP
2
Press MEMORY.
MEMORY
“CH-” appears and the channel number position starts
flashing on the display for about 5 seconds.
DOWN
ANALOG
TUNED STEREO
SPK
L
C
AUTO MUTING
R
VOLUME
S.WFR LFE
LS
RS
S
Notes:
CH-
• When you press and hold FM/AM TUNING UP/DOWN for a few
seconds in step 2, the frequency keeps changing until a station is
tuned in.
• When a station of sufficient signal strength is tuned in, the TUNED
indicator lights up on the display.
• When an FM stereo program is received, the STEREO indicator
also lights up.
3
Press FM/AM PRESET UP/
DOWN to select a channel number
while the channel number position
is flashing.
ANALOG
TUNED STEREO
SPK
L
C
R
FM/AM PRESET
UP
DOWN
AUTO MUTING
VOLUME
S.WFR LFE
LS
S
RS
CH-
16
EN08-17.RX-5022VSL[A]_f
16
02.3.25, 9:32 AM
Tuner Operations
4
Press MEMORY again while the
selected channel number is flashing
on the display.
Selecting the FM Reception Mode
MEMORY
When an FM stereo broadcast is hard to receive or noisy, you can
change the FM reception mode while receiving an FM broadcast.
• You can store the FM reception mode for each preset station (see
page 16).
The selected channel number stops flashing.
The station is assigned to the selected channel number.
ANALOG
TUNED STEREO
SPK
L
C
AUTO MUTING
R
1
VOLUME
S.WFR LFE
LS
S
RS
CH-
5
Repeat steps 1 to 4 until you store all the stations
you want.
While listening to an FM station, press FM
MODE.
• Each time you press the button, the FM reception mode
alternates between “AUTO” and “MONO.”
FM MODE
FM MODE
To erase a stored preset station
Storing a new station on a used number erases the previously stored
one.
On the front panel
ANALOG
1
L
C
TUNED STEREO
S
ANALOG
L
LS
Press FM/AM PRESET UP/ DOWN
until you find the channel you want.
DOWN
Press FM/AM to select the band (FM or
AM).
Press 10 keys to select a preset
channel number.
•
•
•
•
For channel number 5, press 5.
For channel number 15, press +10 then 5.
For channel number 20, press +10 then 10.
For channel number 30, press +10, +10,
then 10.
RS
MONO
: Select this to improve the reception (but stereo
effect will be lost).
In this mode, you will hear noise while tuning into
the stations. The AUTO MUTING indicator goes
off from the display. (The STEREO indicator also
goes off.)
UP
FM/AM
The last received station of the selected band is tuned
in and the10 keys now work for tuner operation.
• Each time you press the button, the band
alternates between FM and AM.
2
S
: Normally select this.
When a program is broadcasted in stereo, you will
hear stereo sound; when in monaural, you will
hear monaural sounds. This mode is also useful to
suppress static noise between stations. The AUTO
MUTING indicator lights up on the display.
(Initial setting)
FM/AM PRESET
From the remote control:
1
R
AUTO
VOLUME
RS
• Pressing FM/AM PRESET UP increases
the channel numbers.
• Pressing FM/AM PRESET DOWN
decreases the channel numbers.
C
CH-
AUTO MUTING
R
TUNED
SPK
S.WFR LFE
CH-
2
To restore the stereo effect
Select “AUTO” in step 1.
TEST
1
CENTER
2
EFFECT
4
5
7/P
10
RETURN
6
REAR R
MENU
ENTER
3
REAR L
8
9
SUBWOOFER
0
10
100
17
EN08-17.RX-5022VSL[A]_f
17
AUTO MUTING
R
RS
FM/AM
S.WFR LFE
LS
S
CH-
The last received station of the selected band is
tuned in.
• Each time you press the button, the band
alternates between FM and AM.
SPK
C
S.WFR LFE
LS
Press FM/AM to select the band
(FM or AM).
ANALOG
TUNED STEREO
SPK
L
To tune in a preset station
On the front panel:
From the remote control
02.3.25, 9:32 AM
Creating Realistic Sound Fields
■ Dolby Surround
Dolby Pro Logic II*
Dolby Pro Logic II has a newly developed multichannel playback
format to decode all 2 channel sources—regular stereo source and
Dolby Surround encoded source—into 5.1 channel.
Matrix-based encoding/decoding method for Dolby Pro Logic II
makes no limitation for the cutoff frequency of the rear treble and
enables stereo rear sound compared to conventional Dolby Pro
Logic.
Dolby Pro Logic II enables to reproduce spacious sound from
original sound without adding any new sounds and tonal colorations.
Dolby Pro Logic II has two modes—Movie mode and Music mode:
Pro Logic II Movie (PL II MOVIE)—suitable for reproduction of
DOLBY SURROUND .
Dolby Surround encoded sources bearing the mark
You can enjoy soundfield very close to the one created with discrete
5.1 channel sounds.
Pro Logic II Music (PL II MUSIC)—suitable for reproduction of
any 2 channel stereo music sources. You can enjoy wide and deep
sound by using this mode. For this mode, Panorama control can be
selected, which gives “wraparound” sound effect with side-wall
image.
• When Dolby Pro Logic II is activated,
indicator lights up on the display.
PRO LOGIC II
Dolby Digital*
Used to reproduce multichannel sound tracks of the software
).
encoded with Dolby Digital (
• To enjoy the software encoded with Dolby Digital, connect the
source component using the digital terminal on the rear of this
receiver. (See page 7.)
D I G I T A L
Dolby Digital 5.1 ch encoding method (so-called discrete
multichannel digital audio format) records and digitally compresses
the left front channel, right front channel, center channel, left rear
channel, right rear channel, and LFE channel signals.
Since each channel is completely independent from the other
channel signals to avoid interference, you can obtain much better
sound quality with much stereo and surround effects.
Note:
Dolby Digital software can be roughly grouped into two categories
—multichannel (up to “5.1” channel) and 2 channel software. To enjoy
surround sounds while playing Dolby Digital 2 ch software, you can
use Dolby Pro Logic II.
■ DTS Digital Surround**
Used to reproduce multichannel sound tracks of the software
encoded with DTS Digital Surround (
).
• To enjoy the software encoded with DTS Digital Surround,
connect the source component using the digital terminal on the
rear of this receiver. (See page 7.)
DTS Digital Surround is another discrete multichannel digital
audio format available on CD, LD, and DVD software.
Compared to Dolby Digital, audio compression ratio is relatively
low. This fact allows DTS Digital Surround format to add breadth
and depth to the reproduced sounds. As a result, DTS Digital
Surround features natural, solid and clear sound.
Typical Multichannel (5.1 ch) reproduction
Center
speaker
Left front
speaker
Subwoofer
Right front
speaker
RX-5020V AUDIO/VIDEO CONTROL RECEIVER
FM/AM TUNING
FM/AM PRESET
FM MODE
STANDBY
MASTER VOLUME
MEMORY
STANDBY/ON
D I G I T A L
SURROUND
SURROUND ON/OFF
INPUT ANALOG
SURROUND MODE
SPEAKERS ON/OFF
INPUT DIGITAL
ADJUST SETTING
DVD
VCR
TV SOUND
TAPE/CDR
FM/AM
INPUT ATT
CONTROL
DOWN
UP
CD
SOURCE NAME
PHONES
Left rear
speaker
* Manufactured under license from Dolby Laboratories. “Dolby,” “Pro
Logic,” and the double-D symbol are trademarks of Dolby
Laboratories. Confidential unpublished works. ©1992–1997 Dolby
Laboratories, Inc. All rights reserved.
Right rear
speaker
** Manufactured underlicense from Digital Theater Systems, Inc. US
PAT. No. 5,451,942 and other world-wide patents issued and
pending. “DTS” and “DTS Digital Surround” are trademarks of
Digital Theater Systems, Inc. Copyright 1996 Digital Theater
Systems, Inc. All rights reserved.
18
EN18-23.RX-5022VSL[A]_f
18
02.3.25, 9:33 AM
Tuner Operations / Creating Realistic Sound Fields
You can use the following Surround modes to reproduce a realistic
sound field:
■ Dolby Surround
• Dolby Pro Logic II
• Dolby Digital
■ DTS Digital Surround
■ DAP (Digital Acoustic Processor) modes
■ All Channel Stereo
Creating Realistic Sound Fields
■ DAP (Digital Acoustic Processor) modes
■ All Channel Stereo
DAP modes have been designed to create important acoustic
surround elements.
This mode can reproduce a larger stereo sound field using all the
connected (and activated) speakers.
The sound heard in a live club, dance club, hall or pavilion consists
of direct sound and indirect sound—early reflections and reflections
from behind. Direct sounds reach the listener directly without any
reflection. On the other hand, indirect sounds are delayed by the
distances of the ceiling and walls (see the diagram below).
These indirect sounds are important elements of the acoustic
surround effects. The DAP mode can reproduce a realistic sound
field by adding these indirect sounds.
All Channel Stereo can be used when the front and rear
speakers are connected to this receiver without respect to the
center speaker connection.
If the center speaker is connected and activated, the same phase of
the front left and right signals are output through the center speaker.
DAP modes can be used when the front and rear speakers are
connected to this receiver (without respect to the center speaker
connection: no sound comes out of the center speaker even if it is
connected).
All Channel Stereo can be used while reproducing 2 channel stereo
software, either analog or digital except Dolby Digital and DTS
Digital Surround.
• When All Channel Stereo is selected, the DSP indicator lights up
on the display.
All Channel Stereo reproduction
The following DAP modes are provided with this receiver:
LIVE CLUB
: Gives the feeling of a live music club with a low
ceiling.
DANCE CLUB : Gives a throbbing bass beat.
HALL
: Gives clear vocal and the feeling of a concert
hall.
PAVILION
: Gives the spacious feeling of a pavilion with a
high ceiling.
These DAP modes can be used to add the acoustic surround effects
while reproducing 2 channel stereo software—either analog or
digital except Dolby Digital and DTS Digital Surround—and can
give you a real “being there” feeling.
• When one of the DAP modes is selected, the DSP indicator lights
up on the display.
Sound reproduced from normal stereo
Creating sound field
Reflections from behind
Early reflections
Sound reproduced from All Channel Stereo
Direct sounds
䡬: Possible / ⳯: Impossible
Available Surround modes for each input signal
Mode SURROUND
Signals
OFF (stereo)
DOLBY
DIGITAL
DTS
SURROUND
PLII
MOVIE
PLII
MUSIC
LIVE
CLUB
DANCE
CLUB
HALL
PAVILION
ALL CH
STEREO
Dolby Digital
(Multichannel)
䡬
䡬
⳯
⳯
⳯
⳯
⳯
⳯
⳯
⳯
Dolby Digital
(2 channel)
䡬
⳯
⳯
䡬
䡬
⳯
⳯
⳯
⳯
⳯
DTS Digital
Surround
(Multichannel)
䡬
⳯
䡬
⳯
⳯
⳯
⳯
⳯
⳯
⳯
DTS Digital
Surround
(2 channel)
䡬
⳯
⳯
䡬
䡬
⳯
⳯
⳯
⳯
⳯
Linear PCM
䡬
⳯
⳯
䡬
䡬
䡬
䡬
䡬
䡬
䡬
Analog
䡬
⳯
⳯
䡬
䡬
䡬
䡬
䡬
䡬
䡬
19
EN18-23.RX-5022VSL[A]_f
19
02.3.25, 9:33 AM
Creating Realistic Sound Fields
About Relations between Speaker Layout and Surround Modes
Available Surround modes will vary depending on how many speakers are used with this receiver.
Make sure that you have set the speaker information correctly (see pages 12 to 14).
• If only front speakers are connected, you cannot use Surround modes.
• If rear speakers are not connected, you cannot use DAP modes and All Channel Stereo.
Speaker Layout
Available Surround modes
When the center and rear speakers
are connected (5 channels):
Turning on or off the Surround modes
Each time you press SURROUND ON/OFF, Surround modes turn on or off.
TUNED STEREO
SPK
Front
speaker
TV
Front
speaker
Center speaker
SURROUND ON/OFF
L
DIGITAL AUTO
LINEAR PCM
AUTO MUTING
PRO LOGIC ΙΙ DSP H.PHONE INPUT ATT
R
S.WFR
ON/OFF
SURROUND
(Remote)
(Front panel)
Last selected
Surround mode
SURROUND OFF
Ex.: “PL II MUSIC” has been selected.
Rear
speaker
Rear
speaker
Selecting the Surround modes
Each time you press SURROUND MODE, Surround modes change as follows:
TUNED STEREO
SPK
When the rear speakers are connected
(4 channels):
Front
speaker
TV
Front
speaker
SURROUND
SURROUND MODE
DIGITAL AUTO
LINEAR PCM
L
AUTO MUTING
PRO LOGIC ΙΙ DSP H.PHONE INPUT ATT
R
VOLUME
S.WFR
MODE
(Remote)
(Front panel)
PL II MOVIE
LIVE CLUB
HALL
ALL CH STEREO
PL II MUSIC
DANCE CLUB
PAVILION
(Back to the beginning)
Note:
Rear
speaker
Rear
speaker
When the center speaker is connected
(3 channels):
When the digital multichannel software such as Dolby Digital or DTS Digital
Surround is played back, the appropriate multichannel Surround mode is
automatically activated (“DOLBY DIGITAL” or “DTS SURROUND”) by pressing
SURROUND ON/OFF (with the digital input mode selected).
• For Dolby Digital 2 channel software, you need to select “PLII MUSIC” or
“PLII MOVIE” by pressing SURROUND MODE.
• For more details, see the table on page 19.
Turning on or off the Surround modes
Each time you press SURROUND ON/OFF, Surround modes turn on or off.
TUNED STEREO
SPK
SURROUND ON/OFF
DIGITAL AUTO
LINEAR PCM
L
AUTO MUTING
PRO LOGIC ΙΙ DSP H.PHONE INPUT ATT
R
S.WFR
ON/OFF
Front
speaker
TV
Center speaker
SURROUND
Front
speaker
(Remote)
(Front panel)
PL II MOVIE
or
PL II MUSIC
SURROUND OFF
Ex.: “PL II MUSIC” has been selected.
Selecting the Surround modes
Each time you press SURROUND MODE, Surround modes change as follows:
SURROUND
SURROUND MODE
(Remote)
TUNED STEREO
SPK
MODE
DIGITAL AUTO
LINEAR PCM
(Front panel)
L
R
AUTO MUTING
PRO LOGIC ΙΙ DSP H.PHONE INPUT ATT
S.WFR
PL II MOVIE
PL II MUSIC
Note:
When the digital multichannel software such as Dolby Digital or DTS Digital
Surround is played back, the appropriate multichannel Surround mode is
automatically activated (“DOLBY DIGITAL” or “DTS SURROUND”) by pressing
SURROUND ON/OFF (with the digital input mode selected).
• For Dolby Digital 2 channel software, you need to select “PLII MUSIC” or
“PLII MOVIE” by pressing SURROUND MODE.
• For more details, see the table on page 19.
20
EN18-23.RX-5022VSL[A]_f
20
02.3.25, 9:33 AM
Creating Realistic Sound Fields
Before you start, remember...
• Make sure that you have set the speaker information correctly (see pages 12 to 14).
• You cannot adjust the center speaker output level when you have set “CNTR SP” to “NONE.”
• You cannot adjust the rear speaker output levels when you have set “REAR SP” to “NONE.”
• Remember not to change the speaker setting while using any Surround modes; otherwise, it may be canceled when you deactivate the
speakers required for the Surround mode.
Front Panel
Display
RX-5022V AUDIO/VIDEO CONTROL RECEIVER
FM/AM TUNING
FM/AM PRESET
UP
FM MODE
UP
ANALOG
DIGITAL AUTO
LINEAR PCM
DIGITAL
STANDBY
MEMORY
DOWN
DOWN
TUNED STEREO
SPK
L
C
PRO LOGIC ΙΙ DSP H.PHONE INPUT ATT
R
AUTO MUTING SLEEP
MASTER VOLUME
VOLUME
S.WFR LFE
LS
S
RS
CH-
STANDBY/ON
SURROUND ON/OFF
INPUT ANALOG
DVD
VCR
TV SOUND
CD
TAPE/CDR
FM/AM
INPUT DIGITAL
ADJUST SETTING
INPUT ATT
SURROUND MODE
CONTROL
DOWN
UP
SPEAKERS ON/OFF
SOURCE NAME
PHONES
ADJUST CONTROL
UP 5/DOWN ∞
SURROUND SURROUND
MODE
ON/OFF
Using Dolby Pro Logic II, Dolby Digital
and DTS Digital Surround
Remote Control
CENTER +/–
TEST
A/V CONTROL
RECEIVER
STANDBY/ON
CENTER
AUDIO
TEST
SOUND
1
REAR L
4
REAR•L +/–
REAR R
7/P
8
VCR
9
SUBWOOFER
ENTER
10
0
DVD
REAR•R +/–
10
100
RETURN
SOUND
TV
6
5
MENU
From the remote control:
3
2
EFFECT
EFFECT
Once you have adjusted the sound, the adjustment is memorized for
each source.
• When playing back digital multichannel software (Dolby Digital
5.1 ch or DTS Digital Surround), the SURROUND MODE button
does not work.
SLEEP
It will be convenient for you to use the remote control for
adjustments, since you can make adjustments from your listening
point by using the test signal.
• For selecting Panorama control for Pro Logic II Music, use the
buttons on the front panel.
SOUND
1
PTY–PTY SEARCH–PTY
REW
FF
REC PAUSE
CD–DISC
TAPE/CDR
CD
DVD
FM/AM
TV SOUND
VCR
When playing back software encoded with Dolby Digital and DTS
Digital Surround, select the digital input mode (see page 11).
ANALOG
/DIGITAL
FM MODE
ON/OFF
TV/VIDEO SURROUND
MUTING
MODE
VCR CH
TV CH
Setting the analog or digital input mode for the
source you like to listen and start playing.
SURROUND
ON/OFF
SURROUND
MODE
TV VOLUME
VOLUME
REMOTE CONTROL RM - SRX5022U
2
Press SURROUND ON/OFF to
activate Surround mode.
ON/OFF
SURROUND
Each time you press the button, Surround mode
turns on and off alternately.
• If you are playing back software encoded with Dolby Digital
multichannel, “DOLBY DIGITAL” is selected.
• If you are playing back software encoded with DTS Digital
Surround, “DTS SURROUND” is selected.
SURROUND
• If you are playing back any software other
MODE
than above, you can select “PL II MUSIC” or
“PL II MOVIE” according to the source by
pressing SURROUND MODE. ( PRO
LOGIC II indicator lights up on the display.)
If you like to adjust sound, go to step 3.
TO BE CONTINUED TO THE NEXT PAGE
21
EN18-23.RX-5022VSL[A]_f
21
02.3.25, 9:33 AM
Press SOUND.
SOUND
3
The 10 keys are activated for sound adjustments.
4
Press TEST to check if you can hear the
sounds through all the speakers at the
equal level.
TEST
1
“TEST TONE L” starts flashing on the display, and a test tone
comes out of the speakers in the following order:
TEST TONE L
TEST TONE C
TEST TONE R
(Left front speaker)
(Center speaker)
(Right front speaker)
TEST TONE LS
TEST TONE RS
(Left rear speaker)
(Right rear speaker)
REAR L : To adjust the left rear speaker output level
(–10 to +10).
REAR R : To adjust the right rear speaker output level
(–10 to +10).
* “0” is the initial setting. If you have already changed the
setting, another number (level) will be shown.
• You can adjust the speaker output levels without outputting the
test tone.
• No test tone comes out of the center speaker when “CNTR SP”
is set to “NONE.”
• No test tone comes out of the rear speakers when “REAR SP”
is set to “NONE.”
Press TEST again to stop the test
tone.
REAR L
5
6
When you select “PL II MUSIC,” you can go to the
following adjustment.
REAR R
9
8
TEST
1
4
Turn on Panorama control or off.
1) Press ADJUST repeatedly until
“PANORAMA” (with the current
setting)* appears on the display.
You can also use the buttons on the front panel to adjust the
Surround modes. However, no test tone is available when using the
buttons on the front panel. So make adjustments while listening to
the sound of the source played back.
Setting the analog or digital input mode for the
source you like to listen and start playing.
2) Press CONTROL UP 5/
DOWN ∞ to select if you turn on
or off Panorama control.
Press SURROUND ON/OFF to
activate Surround mode.
ADJUST SETTING
SURROUND ON/OFF
Each time you press the button, Surround
mode turns on and off alternately.
• If you are playing back software encoded with Dolby Digital
multichannel, “DOLBY DIGITAL” is selected.
• If you are playing back software encoded with DTS Digital
Surround, “DTS SURROUND” is selected.
SURROUND MODE
• If you are playing back any software other
than above, you can select “PL II MUSIC”
or “PL II MOVIE” according to the source
by pressing SURROUND MODE. ( PRO
LOGIC II indicator lights up on the display.)
CONTROL
DOWN
UP
• Each time you press the button, “ON”
and “OFF” change alternately.
ON
: Select this when you like to enjoy
“wraparound” sound effect with side-wall
image.
OFF
: Select this when you like to enjoy
originally recorded sounds.
When playing back software encoded with Dolby Digital and DTS
Digital Surround, select the digital input mode (see page 11).
2
Remote
NOT
*“OFF” is the initial setting. If you have
already changed the setting, “ON” will be
shown.
On the front panel:
1
CONTROL
DOWN
UP
3) Repeat steps 1) and 2) to adjust
the other speaker levels.
3
2
Adjust the center speaker and rear speakers levels
comparing to the sound from the front speakers.
• To adjust the center speaker level, press
CENTER +/–.
• To adjust the left rear speaker level, press
REAR•L +/–.
• To adjust the right rear speaker level, press
REAR•R +/–.
6
2) Press CONTROL UP 5/
DOWN ∞ to adjust the selected
speaker output level.
CENTER
Adjust the speaker output levels
(–10 to +10).
ADJUST SETTING
CENTER : To adjust the center speaker output level
(–10 to +10).
Notes:
5
Adjust the speaker output levels.
1) Press ADJUST repeatedly until one
of the following indications (with the
current setting)* appears on the
display.
To cancel Surround mode
Press SURROUND ON/OFF again so that “SURROUND OFF”
appears on the display.
• If Surround mode is canceled while playing back multichannel
digital software, all channel signals are mixed and output through
the front speakers (and subwoofer, if you have connected a
subwoofer and set the subwoofer setting correctly—“YES”).
If you like to adjust sound, go to step 3.
22
EN18-23.RX-5022VSL[A]_f
22
02.3.25, 9:33 AM
Creating Realistic Sound Fields
3
Creating Realistic Sound Fields
Using DAP Modes and All Channel Stereo
Once you have adjusted the DAP modes and All Channel Stereo, the
adjustment is memorized for each source.
• You cannot use the DAP modes and All Channel Stereo if the rear
speakers are not connected or deactivated.
• You cannot adjust the effect level for “ALL CH STEREO.”
From the remote control:
2
Start playing 2 channel software—either analog
or Linear PCM—and select the source.
2
Press SURROUND ON/OFF to
activate Surround mode.
3
SURROUND MODE
Press SURROUND MODE
repeatedly until one of the DAP
modes—“LIVE CLUB,” “DANCE
CLUB,” “HALL,” “PAVILION”—
or “ALL CH STEREO” appears on the display.
The DSP indicator also lights up on the display.
If you like to adjust sound, go to step 4.
ON/OFF
SURROUND
When Surround mode turns on, the last selected
Surround mode will be activated.
• Each time you press the button, Surround mode turns on and
off alternately.
3
SURROUND ON/OFF
When the Surround mode turns on, the last
selected Surround mode will be activated.
• Each time you press the button, Surround mode turns on and
off alternately.
It will be convenient for you to use the remote control for adjustments,
since you can make adjustments from your listening point.
1
Press SURROUND ON/OFF to
activate Surround mode.
Press SURROUND MODE repeatedly
until one of the DAP modes—“LIVE
CLUB,” “DANCE CLUB,” “HALL,”
“PAVILION”—or “ALL CH
STEREO” appears on the display.
4
Adjust the speaker output levels.
ADJUST
1) Press ADJUST repeatedly until one
of the following indications (with the
current setting)* appears on the display.
SETTIN
REAR L : To adjust the left rear speaker output level
(–10 to +10).
SURROUND
MODE
REAR R : To adjust the right rear speaker output level
(–10 to +10).
The DSP indicator also lights up on the display.
CENTER : For “ALL CH STEREO” only—to adjust the
center speaker output level (–10 to +10).
If you like to adjust sound, go to step 4.
* “0” is the initial setting. If you have already changed the
setting, another number (level) will be shown.
4
Press SOUND.
2) Press CONTROL UP 5/DOWN ∞
to adjust the selected speaker
output level.
3) Repeat steps 1) and 2) to adjust
the other speaker level.
SOUND
The 10 keys are activated for sound adjustments.
5
Adjust the speakers output levels
(–10 to +10).
REAR L
5
• To adjust the left rear speaker level, press
REAR•L +/–.
• To adjust the right rear speaker level, press
REAR•R +/–.
REAR R
9
8
For “ALL CH STEREO” only:
• To adjust the center speaker level, press
CENTER +/–.
6
6
CENTER
EFFECT
4
• Each time you press the button, the effect
level changes as follows:
EFFECT 2
EFFECT 1
EFFECT 5
2) Press CONTROL UP 5/DOWN ∞
to select the effect level (1 to 5) you
want.
CONTROL
DOWN
UP
• Each time you press the button, the effect
level changes as follows:
EFFECT 2
EFFECT 3
EFFECT 1
EFFECT 4
EFFECT 4
EFFECT 5
As the number increases, selected mode becomes stronger
(normally set it to “EFFECT 3”).
Note:
You cannot select any DAP mode and All Channel Stereo when software
encoded with Dolby Digital or DTS Digital Surround is played back.
On the front panel:
Start playing 2 channel software—either analog
or Linear PCM—and select the source.
To cancel DAP modes and All Channel Stereo
Press SURROUND ON/OFF so that “SURROUND OFF” appears
on the display. The DSP indicator goes off.
23
EN18-23.RX-5022VSL[A]_f
SETTI
* “EFFECT 3” is the initial setting. If you have already
changed the setting, another setting will be shown.
EFFECT 3
As the number increases, selected mode becomes stronger
(normally set it to “EFFECT 3”).
1
For DAP modes only: Adjust the effect level.
ADJUST
1) Press ADJUST repeatedly until
“EFFECT” (with the current
setting)* appears on the display.
3
2
For DAP modes only:
Press EFFECT to select the effect
level (1 to 5) you want.
5
CONTROL
DOWN
UP
23
02.3.25, 9:33 AM
COMPU LINK Remote Control System
Automatic Power On/Off (Standby): only possible with the
COMPU LINK-3 and COMPU LINK-4
Both the CD player and cassette deck (or CD recorder) turn on and
off (standby) along with the receiver.
When you turn on the receiver, the CD player or cassette deck (or
CD recorder) will turn on automatically, depending on which
component has been previously selected.
When you turn off the receiver, both the CD player and cassette
deck (or CD recorder) will turn off (standby).
Synchronized Recording
Cassette deck
or
CD recorder
Synchronized recording means the cassette deck starts recording as
soon as a CD begins playing.
To use synchronized recording, follow these steps:
COMPU LINK-4
(SYNCHRO)
1 Put a tape in the cassette deck and a disc in the
CD player.
CD player
Notes:
• There are four versions of COMPU LINK remote control system.
This receiver is equipped with the fourth version—COMPU LINK-4.
This version is added systematic operations with the CD recorder to
the previous version—COMPU LINK-3.
• If your audio component has two COMPU LINK jacks, you can use
either one. If it has only one COMPU LINK jack, connect it so that it
is the last item in the series of components.
• To operate the cassette deck or CD recorder using the COMPU
LINK remote control system, set the source name correctly.
(See page 8.)
• Refer also to the manuals supplied with your audio components.
This remote control system allows you to use four functions listed
below.
2 Press the record (¶) button and the pause (8)
button on the cassette deck at the same time.
This puts the cassette deck into recording pause.
If you do not press the record (¶) button and pause (8) button at
the same time, the synchronized recording feature will not
operate.
3 Press the play (3) button on the CD player.
The source changes on the receiver, and as soon as play starts,
the cassette deck starts recording. When the play ends, the
cassette deck enters recording pause, and stops about 4 seconds
later.
Notes:
• During synchronized recording, the selected source cannot be
changed.
• If the power of any component is shut off during synchronized
recording, the COMPU LINK remote control system may not
operate properly. In this case, you must start again from the
beginning.
Remote Control through the Remote Sensor on the Receiver
You can control the connected audio components through the remote
sensor on the receiver using this remote control. Aim the remote
control directly at the remote sensor on the receiver. For details, see
pages 25 to 27.
Automatic Source Selection
3) button on a connected component or
When you press the play (3
on its own remote control, the receiver automatically turns on and
changes the source to the component. On the other hand, if you
select a new source on the receiver or on the remote control, the
selected component begins playing immediately.
In both cases, the previously selected source continues playing
without sound for a few seconds.
24
EN24-30.RX-5022VSL[A]_f
24
02.3.25, 9:34 AM
Creating Realistic Sound Fields / COMPU LINK Remote Control System
The COMPU LINK remote control system allows you to operate
JVC’s audio components through the remote sensor on the receiver.
To use this remote control system, you need to connect JVC’s audio
components through the COMPU LINK-4 (SYNCHRO) jacks (see
below) in addition to the connections using cables with RCA pin
plugs (see page 6).
• Make sure that the AC power cords of these components are
unplugged before connection. Plug the AC power cords only after
all connections are completed.
Operating JVC’s Audio/Video Components
You can use the remote control to operate other JVC’s
components.
Operating Audio Components
Sound Adjustment
You can always perform the following operations:
SURROUND ON/OFF : Turn on or off the Surround modes.
SURROUND MODE
: Select the Surround modes.
IMPORTANT:
To operate JVC’s audio components using this remote control:
• You need to connect JVC’s audio components through the COMPU
LINK (SYNCHRO) jacks (see page 24) in addition to the
connections using cables with RCA pin plugs (see page 6).
• Aim the remote control directly at the remote sensor on the receiver.
• If you use the buttons on the front panel, the remote control will not
operate that source. To operate a source with the remote control,
the source must be selected using source selecting buttons on the
remote control.
• To operate the cassette deck or CD recorder using the COMPU
LINK remote control system, set the source name correctly. (See
page 8.)
• Refer also to the manuals supplied with your audio components.
After pressing SOUND, you can use the following buttons for sound
adjustment:
SUBWOOFER +/–
: Adjust the subwoofer output level.
CENTER +/–
: Adjust the center speaker output level.
REAR•L +/–
: Adjust the left rear speaker output level.
REAR•R +/–
: Adjust the right rear speaker output level.
EFFECT
: Select the DAP effect level.
TEST
: Turn on or off the test tone output.
Note:
After adjusting sounds, press the corresponding source selecting
button or CD-DISC to operate your target source by using the 10
keys; otherwise, the 10 keys cannot be used for operating your target
source.
A/V CONTROL
RECEIVER
STANDBY/ON
CENTER
AUDIO
TEST
1
3
2
REAR L
EFFECT
4
TV
6
5
REAR R
MENU
7/P
8
VCR
9
SUBWOOFER
ENTER
10
0
DVD
You can always perform the following operations:
FM/AM
: Alternate between FM and AM.
FM MODE
: Change the FM reception mode.
10
100
RETURN
Tuner
SLEEP
SOUND
PTY–PTY SEARCH–PTY
REW
FF
REC PAUSE
CD–DISC
TAPE/CDR
CD
DVD
FM/AM
TV SOUND
VCR
ANALOG
/DIGITAL
After pressing FM/AM, you can use the following buttons for tuner
operations:
1 – 10, +10
: Select a preset channel number directly.
• For channel number 5, press 5.
• For channel number 15, press +10, then 5.
• For channel number 20, press +10, then 10.
FM MODE
ON/OFF
TV/VIDEO SURROUND
MUTING
MODE
VCR CH
TV CH
TV VOLUME
VOLUME
REMOTE CONTROL RM - SRX5022U
25
EN24-30.RX-5022VSL[A]_f
25
02.3.25, 9:34 AM
Cassette deck
After pressing CD, you can use the following buttons for CD
operations:
After pressing TAPE/CDR, you can use the following buttons for
cassette deck operations:
3
: Start playback.
3
: Start playback.
4
: Return to the beginning of the current
(or previous) track.
FF
: Fast wind the tape from left to right.
REW
: Fast wind the tape from right to left.
¢
: Skip to the beginning of the next track.
7
: Stop playback or recording.
7
: Stop playback.
8
: Pause playback. To release it, press 3.
8
: Pause playback. To release it, press 3.
REC PAUSE
1 – 10, +10
: Select a track number directly.
• For track number 5, press 5.
• For track number 15, press +10, then 5.
• For track number 20, press +10, then 10.
: Press this button to enter recording pause.
Press this button then 3 to start recording.
CD changer
After pressing CD-DISC, you can use the following buttons for CD
changer operations:
3
: Start playback.
4
: Return to the beginning of the current
(or previous) track.
¢
: Skip to the beginning of the next track.
7
: Stop playback.
8
: Pause playback. To release it, press 3.
1 – 6, 7/P
: Select the number of a disc installed in a CD
changer.
Note:
Before starting the above operations, make sure that you have
changed the source name correctly. See page 8.
CD recorder
After pressing TAPE/CDR, you can use the following buttons for
CD recorder operations:
3
: Start playback.
4
: Return to the beginning of the current
(or previous) track.
¢
: Skip to the beginning of the next track.
7
: Stop playback or recording.
8
: Pause playback. To release it, press 3.
REC PAUSE
: Press this button to enter recording pause.
Press this button then 3 to start recording.
Note:
Before starting the above operations, make sure that you have
changed the source name correctly. See page 8.
26
EN24-30.RX-5022VSL[A]_f
26
02.3.25, 9:34 AM
Operating JVC‘s Audio/Video Components
CD player
Operating JVC’s Audio/Video Components
Operating Video Components
IMPORTANT:
To operate JVC’s video components using this remote control:
• Some JVC’s VCRs can accept two types of the control signals—
remote code “A” and “B.” Before using this remote control, make
sure that the remote control code of the VCR connected to the VCR
jacks is set to code “A.”
• Aim the remote control directly at the remote sensor on each
component, not on the receiver.
DVD menu operations
After pressing DVD (source selecting button),
you can use the following buttons for DVD
menu operations:
TEST
1
CENTER
2
EFFECT
4
7/P
10
RETURN
MENU
: Display or erase the menu screen.
5/∞
∞/3
3/2
2
: Select an item on the menu screen.
ENTER
: Enter a selected item.
6
REAR R
MENU
ENTER
3
REAR L
5
8
9
SUBWOOFER
0
10
100
VCR
You can always perform the following operations:
STANDBY/ON
VCR CH +/–
VCR
: Turn on or off a VCR.
: Change the TV channels on the VCR.
After pressing VCR (source selecting button), you can use the
following buttons for VCR operations:
3
: Start playback.
FF
: Fast wind a tape.
REW
: Rewind a tape.
7
: Stop playback or recording.
8
: Pause playback. To release it, press 3.
REC PAUSE
: Press this button to enter recording pause.
Press this button then 3 to start recording.
TV
You can always perform the following operations:
STANDBY/ON
TV : Turn on or off a TV.
TV/VIDEO
: Change the input mode (TV tuner and video
input).
TV VOLUME +/–
: Adjust the volume.
TV CH +/–
: Change the channels.
After pressing TV SOUND (source selecting button), you can use
the following buttons for TV operations:
1 – 9, 0, 100+ (+10)
: Select a channel.
RETURN (10)
: Function as the RETURN button.
DVD player
You can always perform the following operations:
STANDBY/ON
DVD
: Turn on or off a DVD player.
After pressing DVD (source selecting button), you can use the
following buttons for DVD operations:
3
: Start playback.
4
: Return to the beginning of the current
(or previous) chapter.
¢
: Skip to the beginning of the next chapter.
7
: Stop playback.
8
: Pause playback. To release it, press 3.
27
EN24-30.RX-5022VSL[A]_f
27
02.3.25, 9:34 AM
Troubleshooting
PROBLEM
POSSIBLE CAUSE
SOLUTION
The power does not come on.
The power cord is not plugged in.
Plug the power cord into an AC outlet.
No sound from speakers.
Speaker signal cables are not connected.
Check speaker wiring and reconnect if
necessary.
The SPEAKERS ON/OFF button is not
set correctly.
Press SPEAKERS ON/OFF button correctly.
An incorrect source is selected.
Select the correct source.
Muting is activated.
Press MUTING to cancel the mute.
An incorrect input mode (analog or
digital) is selected.
Select the correct input mode (analog or
digital).
Connections are incorrect.
Check connections.
For analog connections, see page 6.
For digital connections, see page 7.
Speaker signal cables are not connected
properly.
Check speaker wiring and reconnect if
necessary.
The balance is set to one extreme.
Adjust the balance properly (see page 15).
Incoming signal is too weak.
Connect an outdoor FM antenna or contact
your dealer.
The station is too far away.
Select a new station.
An incorrect antenna is used.
Check with your dealer to be sure you have
the correct antenna.
Antennas are not connected properly.
Check connections.
Occasional cracking noise during FM
reception.
Ignition noise from automobiles.
Move the antenna farther from automobile
traffic.
“OVERLOAD” starts flashing on the
display.
Speakers are overloaded because of high
volume.
on the front
1. Press STANDBY/ON
panel to turn off the receiver.
2. Stop the playback source.
3. Turn on the receiver again, and adjust the
volume.
Speakers are overloaded because of short
circuit of speaker terminals.
on the front panel,
Press STANDBY/ON
then check the speaker wiring.
If “OVERLOAD” does not disappear, unplug
the AC power cord, then plug it back again.
If speaker wiring is not short-circuited, contact
your dealer.
“DSP MICOM NG” starts flashing on the
display.
The built-in microcomputer is not
functioning correctly.
on the front panel to
Press STANDBY/ON
turn off the receiver. After unplugging the
power cord, consult your dealer.
The STANDBY lamp lights up after
turning on the power, but soon the
receiver turns off (into standby mode).
The receiver is overloaded because of a
high voltage.
on the front panel to
Press STANDBY/ON
turn off the receiver. After unplugging the
power cord, consult your dealer.
Remote control does not work.
There is an obstruction in front of the
remote sensor on the receiver.
Remove the obstruction.
Batteries are weak.
Replace batteries.
The remote control is not ready for your
intended operation.
Press SOUND or a source selecting button
first, then press the buttons you want to use.
(See pages 25 to 27).
Sound from one speaker only.
Continuous hiss or buzzing during FM
reception.
Remote control does not work as you
intend.
28
EN24-30.RX-5022VSL[A]_f
28
02.3.25, 9:34 AM
Operating JVC‘s Audio/Video Components / Troubleshooting
Use this chart to help you solve daily operational problems. If there is any problems you cannot solve, contact your JVC’s service center.
Specifications
Designs & specifications are subject to change without notice.
Amplifier
Output Power
At Stereo operation:
Front channels:
100 W per channel, min. RMS, both channels driven into 8 Ω at
1 kHz with no more than 0.9% total harmonic distortion.
(IEC268-3/DIN)
At Surround operation:
Audio
Audio Input Sensitivity/Impedance (1 kHz):
Front channels:
100 W per channel, min. RMS, driven into 8 Ω at 1 kHz, with no
more than 0.8% total harmonic distortion.
Center channel:
100 W, min. RMS, driven into 8 Ω at 1 kHz, with no more than
0.8% total harmonic distortion.
Rear channels:
100 W per channel, min. RMS, driven into 8 Ω at 1 kHz, with no
more than 0.8% total harmonic distortion.
CD, TAPE/CDR, TV SOUND, VCR, DVD:
220 mV/47 k Ω
Audio Input (DIGITAL IN)* :
Coaxial: DIGITAL 1 (DVD):
Optical: DIGITAL 2 (CD):
0.5 V (p-p)/75 Ω
–21 dBm to –15 dBm (660 nm ±30 nm)
* Corresponding to Linear PCM, Dolby Digital, and DTS Digital Surround
(with sampling frequency — 32 kHz, 44.1 kHz, 48 kHz).
Audio Output Level:
Signal-to-Noise Ratio (’66 IHF/DIN):
Frequency Response (8 Ω):
Tone Control:
TAPE/CDR, VCR:
220 mV
CD, TAPE/CDR, TV SOUND, VCR, DVD: 87 dB/67 dB
CD, TAPE/CDR, TV SOUND, VCR, DVD: 20 Hz to 20 kHz (±1 dB)
Bass (100 Hz):
Treble (10 kHz):
±10 dB
±10 dB
VCR, DVD:
1 V (p-p)/75 Ω
VCR, MONITOR OUT:
1 V (p-p)/75 Ω
Video
Video Input Sensitivity/Impedance:
Composite video:
Video Output Level/Impedance:
Composite video:
Synchronization:
Signal-to-Noise Ratio:
Negative
45 dB
29
EN24-30.RX-5022VSL[A]_f
29
02.3.25, 9:34 AM
Tuning Range:
87.50 MHz to 108.00 MHz
Usable Sensitivity:
Monaural:
17.0 dBf (1.95 µV/75 Ω)
50 dB Quieting Sensitivity:
Monaural:
Stereo:
21.3 dBf (3.2 µV/75 Ω)
41.3 dBf (31.5 µV/75 Ω)
Signal-to-Noise Ratio (IHF-A weighted):
Monaural:
Stereo:
78 dB at 85 dBf
73 dB at 85 dBf
Total Harmonic Distortion:
Monaural:
Stereo:
0.4% at 1 kHz
0.6% at 1 kHz
Stereo Separation at REC OUT:
Alternate Channel Selectivity:
Frequency Response:
Specifications
FM tuner (IHF)
35 dB at 1 kHz
45 dB: (±400 kHz)
30 Hz to 15 kHz: (+0.5 dB, –3 dB)
AM tuner
Tuning Range:
Usable Sensitivity:
Signal-to-Noise Ratio:
522 kHz to 1 629 kHz
Loop antenna:
400 µV/m
50 dB (100 mV/m)
General
Power Requirements:
AC 240V
Power Consumption:
200 W (at operation)
2 W (in standby mode)
Dimensions (W x H x D):
Mass:
, 50 Hz
435 mm x 146.5 mm x 416 mm
9.8 kg
30
EN24-30.RX-5022VSL[A]_f
30
02.3.25, 9:34 AM
VICTOR COMPANY OF JAPAN, LIMITED
V
EN
RX-5022VSL[A]_COVER_f
J
2
02.3.25, 9:35 AM
C
0402NHMMDWJEIN
Download PDF
Similar pages