Catalogue 2014
1
GTi Pro LITE.............................................................................................................................................4 - 5
GTi Pro HVLP and Trans-Tech Spray Guns..............................................................................................6 - 7
PRi Pro Trans-Tech Gravity Feed Primer Spray Gun................................................................................8 - 9
SRi Pro LITE and MICRO.....................................................................................................................10 - 11
SRi Pro HVLP Spot Repair Gravity Feed Spray Gun............................................................................12 - 13
GPi . ....................................................................................................................................................14 - 15
GFG Pro Conventional Gravity Feed Spray Gun.................................................................................16 - 17
FLG-5 General Purpose Gravity and Suction Feed Spray Guns..........................................................18 - 19
DAGR Airbrush....................................................................................................................................20 - 21
GTi Pro Compliant Suction and Pressure Feed Spray Guns................................................................22 - 23
GTi Pro LITE Suction and Pressure Feed Spray Guns..........................................................................24 - 25
JGA Pro Conventional Suction and Pressure Feed Spray Guns..........................................................26 - 27
Startingline Gun.........................................................................................................................................28
Pro Clean....................................................................................................................................................29
Shim Mask..................................................................................................................................................30
DMG Air Dryer Guns and Systems.............................................................................................................31
DGi Pro Gauges.........................................................................................................................................32
DeKups.......................................................................................................................................................33
CLEAN Range......................................................................................................................................34 - 35
Pro Visor..............................................................................................................................................36 - 37
MPV-627 Air Fed Half Mask Outfit......................................................................................................38 - 39
Valuair and Freedom Half Mask Respirators...............................................................................................40
ProAir-1 Filter Regulator.............................................................................................................................41
ProAir-2 Filter Regulator Coalescer............................................................................................................42
ProAir-3 Filter Regulator.............................................................................................................................43
Finishline Economy Regulators..................................................................................................................44
Gun Spares.................................................................................................................................................45
Accessories - Gravity and Suction Cups.....................................................................................................46
Accessories - Spray Gun......................................................................................................................47 - 48
Accessories - Hoses and Connections........................................................................................................49
KBII 2.3 Litre Remote Cup...................................................................................................................50 - 51
DX Pumps............................................................................................................................................52 - 53
MXL Pumps.........................................................................................................................................54 - 55
Binks Pressure Feed Tank....................................................................................................................56 - 57
DVFR Filter Regulators........................................................................................................................58 - 59
CVi..............................................................................................................................................................60
GTiW / GTiG / PRi......................................................................................................................................61
GTiP / GTiS.................................................................................................................................................62
SRi / SRiW...................................................................................................................................................63
VRiS & P / VRiG...................................................................................................................................64 - 65
JGAS...........................................................................................................................................................66
GFG............................................................................................................................................................67
MPV-623.....................................................................................................................................................68
MPV-616.....................................................................................................................................................69
Data Sheets.........................................................................................................................................70 - 95
Conditions of Sale...............................................................................................................................96 - 98
ATEX...........................................................................................................................................................99
Catalogue 2015
3
A lightweight DeVilbiss spray gun developed for busy professional painters needing the
ultimate in quality finishes.
Range of four advanced technology air caps (one HVLP and three High Efficiency) for
optimum application performance with the latest solvent and waterborne coatings.
Ergonomic gun body design with even better fit and balance for comfort and control.
Four high efficiency fluid tips provide superb versatility across a range of climatic
conditions and viscosities.
Coaxial, low kick air valve design gives smoother feel for even greater air and paint
control for ease of fade-outs and blend-ins.
art Number Explanation
P
PROL - TE10 - B - 13
Model
HV30 HVLP
Air Cap
Air Cap
Base
TE10 High Efficiency
Air Cap
Specification
Air Inlet Pressure
Air Consumption
Air Inlet Thread
2.0 bar (29psi) for TE Caps
1.75 bar (25 psi) for HV Cap
TE10: 270 l/min (9.5 cfm)
TE20: 360 l/min (12.7 cfm)
HV30: 460 l/min (16.3 cfm)
T110: 265 l/min (9.4 cfm)
1/4” Universal
Fluid Tip
TE20 High Efficiency
Air Cap
Cup Capacity
Weight (gun only)
Weight (gun & cup)
Air Cap
Air Cap Retaining Ring
Fluid Tip
Fluid Needle
T110 High Efficiency
Air Cap
560 mls
446 gms
620 gms
Plated Brass
Clear Anodised Aluminium
Stainless Steel
Stainless Steel
KGP-5-K5
GTi Pro LITE Spray Gun Kits
When ordering please specify the air cap of your choice (HV30, TE10, TE20, T110), the tip size of your choice (12, 13 or 14) and the paint type
marking required on your gun B=BASE, C=CLEAR.
Part No Examples
PROL-TE10C-13
PROL-HV30B-D-12
4900-5-1-K3
Description
GTi Pro LITE kit with TE10 High Efficiency air cap, #13 fluid tip, marked as “Clear”
Digital GTi Pro LITE kit with HV30 High Efficiency air cap, #12 fluid tip, marked as “Base”
Kit includes GTi Pro LITE gun, gravity cup, paint filter, brush, torx key, set of 4 identification rings and combination spanner
Accessories
Part No
PRO-102-HV30-K
PRO-102-TE10-K
PRO-102-TE20-K
PRO-102-T110-K
PROL-455-****-**
PRO-200-**-K
PRO-301-K
PRO-470
SN-406
DGIPRO-502-BAR
DGIPRO-504-BAR-K
MPV-60-K3
HAF-507-K12
4900-5-1-K3
KGP-5-K5
4
MPV-60-K3
Description
HV30 HVLP Air Cap and retaining ring
TE10 High Efficiency Air Cap and retaining ring
TE20 High Efficiency Air Cap and retaining ring
T110 High Efficiency Air Cap and retaining ring
Air cap, fluid tip and needle kit
Fluid Tip - Size Numbers 12, 13 & 14
Pro LITE Fluid Needle
Spray Gun Service/Repair Kit
Gun wrench, Torx & flat back screwdriver, cleaning brush and colour ID rings
Digital gauge for air inlet fitting - Reads in bars
Digital gauge for spreader valve assembly for GTi Pro LITE - reads in bars
Pack of three male quick detach uni swivel - fits to gun air inlet
Lightweight in-line air filter (pack of 12)
Pack of three cleaning brushes
Pack of 5 gravity cup filters for GFC cups
HAF-507-K12
PRO-470
**** = Air Cap
** = Fluid tip size
Catalogue 2015
PRO-470 Repair Kit includes:
Packing, Spring & Packing Nut
SN-404
Trigger Stud & Screw*
Spray Head Seal
SN-18-1
Seal and Pin Kit
GTI-428-K5
Needle Spring
PRO-472
*Not sold separately
Ref
No
1
2
3
4
5
6
7
8
9
10
Description
Air Cap Retaining Clip
TE10 High Efficiency Air Cap & Ring
TE20 High Efficiency Air Cap & Ring
HV30 HVLP Air Cap & Ring
T110 High Efficiency Air Cap & Ring
Air Cap Retaining Ring & Seals
Fluid Tip 12, 13 or 14
Spray Head Seal (kit of 2)
Spray Head & Seal Kit
Fluid Needle
Fluid Adjusting Knob
Spreader Valve Assembly
Packing, Spring & Packing Nut Kit
Catalogue 2015
Part Number
JGA-156-K5
PRO-102-TE10-K
PRO-102-TE20-K
PRO-102-HV30-K
PRO-102-T110-K
PRO-420-K
PRO-200**-K
SN-18-1-K2
SN-69-K
PRO-301-K
SN-67-C-K
PRO-406-K
SN-404-K
Ref
No
11
12
13
14
15
16
17
18
19
20
21
22
23
Description
Needle Spring Kit
Trigger, Stud & Screw Kit
Air Inlet
Colour ID Ring Kit (4 Colours)
Airflow Valve (Cheater)
Air Valve Kit
Body Housing
Gravity Cup Kit
Drip Check Lid (kit of 5)
Gravity Cup Lid
Filter
Torx Key & Spanner
Torx Key
Part Number
PRO-472-K3
SP-617-CR-K
SN-9-K
SN-26-K4
PRO-407-K
PRO-471
SN-66-K
GFC-501
GFC-2-K5
GFC-402
KGP-5-K5
SN-406
SPN-8-K2
5
High Performance, Base and Clearcoat Technology
Spray guns
The gun can be purchased with or without the DGi Pro pod Digital gauge factory fitted (this
gauge can also be retrofitted to standard guns).
Four advanced technology air caps (one HVLP and three Trans-Tech) for optimum
application performance with the latest solvent and waterborne coatings.
Ergonomic gun body design with even better fit and balance for comfort
and control.
Ultra high flow fluid tips provide superb versatility across a range of viscosities.
Revolutionary air valve design gives smoother feel for even greater air and paint
control for ease of fade-outs and blend-ins.
Simplified, user friendly components provide easy cleaning and maintenance.
art Number Explanation
P
GTIPRO - T1 - B - D - 13
Model
No H1 HVLP
Air Cap
Air Cap
BaseDigital Models Fluid Tip
No T1 Trans-Tech
Air Cap
Specification
Air Inlet Pressure
Air Consumption
Air Inlet Thread
2.0 bar (29psi)
T1: 280 l/min (9.9 cfm)
T2: 350 l/min (12.4 cfm)
H1 450 l/min (15.9 cfm)
T110: 265 l/min (9.4 cfm)
1/4” Universal
No T2 Trans-Tech
Air Cap
Cup Capacity
Weight (gun & cup)
Digital Weight (gun & cup)
Air Cap & Ring
Fluid Tip
Fluid Needle
No T110 Trans-Tech
Air Cap
560 mls
768 gms
823 gms
Plated Brass
Stainless Steel
Stainless Steel
DGIPRO-503BAR-K
GTi Pro Spray Gun Kits
When ordering please specify the air cap of your choice (H1, T1 or T2), the tip size of your choice (12, 13 or 14) and the paint type
marking required on your gun B=BASE, C=CLEAR and add in a –D if you require the gun complete with digital pod gauge.
Part No Examples
GTIPRO-T1C-13
GTIPRO-H1B-D-12
Description
Gun with a T1 Trans-Tech air cap, a #13 fluid tip and marked as “CLEAR”
Digital Gun with a H1 HVLP air cap, a #12 fluid tip and marked as “BASE”
Kit includes GTi PRO Gravity gun, cup, paint filter, brush, set of 4 identification rings and combination spanner
MPV-60-K3
Accessories
Part No
PRO-100-H1-K
PRO-100-T1-K
PRO-100-T2-K
PRO-100-T110-K
PRO-450-***-**
PRO-200-**-K
PRO-300-K
PRO-415-1
SN-406
DGIPRO-502-BAR
DGIPRO-503-BAR-K
MPV-60-K3
HAF-507-K12
4900-5-1-K3
KGP-5-K5
PRO-15-K3
6
Description
H1 HVLP Air Cap and retaining ring
T1 Trans-Tech Air Cap and retaining ring
T2 Trans-Tech Air Cap and retaining ring
T110 Trans-Tech Air Cap and retaining ring
Air cap, fluid tip and needle kit
Fluid Tip - Size Numbers 12, 13 & 14
Fluid Needle
Spray Gun Service/Repair Kit
Gun wrench, Torx & flat back screwdriver, cleaning brush and colour ID rings
Digital Gauge - Reads in bars
Digital gauge for spreader valve assembly for GTi Pro - reads in bars
Male Quick Detach Uni Swivel - fits to gun air inlet
Lightweight in-line air filter (pack of 12)
Pack of three cleaning brushes
Pack of 5 gravity cup filters for GFC cups
ProClip - snap on trigger locking clip
HAF-507-K12
PRO-415-1
*** = Air Cap
** = Fluid tip size
Catalogue 2015
PRO-415-1 Repair Kit includes:
Seal & Pin Kit (5 Pack)
Fluid Needle Spring (Sub Assy)
Needle Packing
Body Bushing Gasket
Trigger Stud
Sprayhead Gasket
Screw
Separator
Ref
No
Description
Part Number
1
Air Cap Retaining Clip
2
T1 Trans-tech® Aircap & Ring
T2 Trans-tech Aircap & Ring
H1 HVLP Aircap & Ring
3
4
GTI-428 K5
SN-409
SN-404
SN-8
SN-13
SN-18-1
SN-22
SRIPRO-2
Ref
No
Description
JGA-156-K5
13
Trigger, Stud & Screw Kit
SN-21-K
PRO-100-T1-K
14
Insert – Pack of 5 (with DGi Pod Only)
SN-57-K5
PRO-100-T2-K
15
Air Inlet
SN-40-K
PRO-100-H1-K
16
Colour ID Ring Kit (4 Colours)
SN-26-K4
Air Cap Retaining Ring & Seals
PRO-405-K
17
Airflow Valve
PRO-411-K
Fluid Tip – 12, 13, 14
PRO-200-**-K
18
Baffle plate
SN-41-K
5
Spray Head Seal (kit of 2)
SN-18-1-K2
19
Gravity Cup Kit
GFC-501
6
Spray Head & Seal Kit
SN-17-1-K
20
Drip Check Lid (kit of 5)
GFC-2-K5
7
Body Bushing & Seal
SN-6-K
21
Gravity Cup Lid
GFC-402
8
Fluid Needle
PRO-300-K
22
Filter
KGP-5-K5
9
Fluid Adjusting Knob, Spring & Pad Kit
PRO-3-K
23
Torx Key
SPN-8-K2
10
Spreader Valve Assembly
PRO-402-K
24
Trigger Stud & Torx Screw (kit of 5)
SN-405-K5
11
Packing, Spring & Packing Nut Kit
SN-404-K
25
Needle spring and pad kit
SN-4-K3
12
Air Valve Replacement Kit
SN-402-K
26
Air valve seal & service tool
SN-34-K5
®
Catalogue 2015
Part Number
7
HIGH PERFORMANCE, GRAVITY FEED, PRIMER SPRAY GUN
Advanced technology P1 Trans-Tech Air Cap.
Suitable for all primers including latest generation waterbase materials.
Fluid Tip sizes available for fillers, surfacers and polyesters.
First class atomisation and material distribution.
Utilises new design air valve for smooth triggering control.
All new ergonomic gun body with improved “fit and feel”.
Large spray patterns for fast and easy application.
Drop forged body with tough anodised finish for protection.
art Number Explanation
P
PRiPRO - P1P - XX
Model
Air Cap
Fluid Tip
Specification
Air Inlet Pressure
2.0 bar (29psi)
Air Consumption
300 l/min (10.6 cfm)
Air Inlet Thread
1/4” Universal
Cup Capacity
560 mls
Weight (gun & cup)
760 gms
Air Cap & Ring
Plated Brass
Fluid Tip
Stainless Steel
Fluid Needle
Stainless Steel
No P1
Trans-Tech Air Cap
PRi Spray Gun Kits
Part No
Description
PRiPRO-P1P-14
Gravity Gun & Cup – P1 Air Cap & No. 14 Fluid Tip
PRiPRO-P1P-16
Gravity Gun & Cup – P1 Air Cap & No. 16 Fluid Tip
PRiPRO-P1P-18
Gravity Gun & Cup – P1 Air Cap & No. 18 Fluid Tip
PRiPRO-P1P-20
Gravity Gun & Cup – P1 Air Cap & No. 20 Fluid Tip
PRiPRO-P1P-25
Gravity Gun & Cup – P1 Air Cap & No. 25 Fluid Tip
DGIPRO-502-BAR
Kit includes PRiPRO Gravity Gun, cup, paint filter, brush and multi-fit spanner
Accessories
Part No
Description
PRIPRO-100-P1-K
Air cap and retaining ring
PRIPRO-210-**-K
Fluid Tip - Size Numbers 14,16,18, 20 & 25
PRIPRO-310--K
Fluid needle
PRO-415-1
Spray gun repair kit – includes seals, packing and springs
DGIPRO-502-BAR
Digital pressure gauge – reads in bars
HAF-507-K12
Lightweight, in-line air filter (pack of 12)
KGP-5-K5
Pack of gravity cup filters for GFC cups
GFC-501
Replacement gravity cup complete (0.6 litre)
4900-5-1-K3
Pack of three cleaning brushes
MPV-60-K3
Male quick detach Uni swivel stem to fit onto gun air inlet
GFV-50-F
Gravity gun bench top stand
GFG-6
Wall mounting bracket for gun and cup
PRO-15-K3
ProClip - snap on trigger locking clip
** = Fluid tip size
8
KGP-5-K5
GFV-50-F
MPV-60-K
Catalogue 2015
PRO-415-1 Repair Kit includes:
Seal & Pin Kit (5 Pack)
Fluid Needle Spring (Sub Assy)
Needle Packing
Body Bushing Gasket
Trigger Stud
Sprayhead Gasket
Screw
Separator
Ref
No
Description
Part Number
Ref
No
Description
GTI-428 K5
SN-409
SN-404
SN-8
SN-13
SN-18-1
SN-22
SRIPRO-2
Part Number
1
Air Cap Retaining Clip
JGA-156-K5
14
Air valve seal & service tool
SN-34-K5
2
Trans-tech® Aircap
PRIPRO-100-P1-K
15
Air Inlet
SN-40-K
3
Air Cap Retaining Ring & Seals
PRO-405-K
16
Colour ID Ring Kit (4 Colours)
SN-26-K4
4
Fluid Tip – 14, 16, 18, 20, 25
PRIPRO-210-**-K
17
Airflow Valve
PRO-411-K
5
Spray Head Seal (kit of 2)
SN-18-1-K2
18
Baffle plate
SN-41-K
6
Spray Head & Seal Kit
SN-17-1-K
19
Gravity Cup Kit
GFC-501
7
Body Bushing & Seal
SN-6-K
20
Drip Check Lid (kit of 5)
GFC-2-K5
8
Fluid Needle
PRIPRO-310-K
21
Gravity Cup Lid
GFC-402
9
Fluid Adjusting Knob, Spring & Pad Kit
PRO-3-K
22
Filter
KGP-5-K5
10
Spreader Valve Assembly
PRO-402-K
23
Torx Key
SPN-8-K2
11
Packing, Spring & Packing Nut Kit
SN-404-K
24
Trigger Stud & Torx Screw (kit of 5)
SN-405-K5
12
Air Valve Replacement Kit
SN-402-K
25
Needle spring and pad kit
SN-4-K3
13
Trigger, Stud & Screw Kit
SN-21-K
Catalogue 2015
9
COMPLIANT SMART / SPOT REPAIR GRAVITY FEED
SPRAY GUN
Two new models of SRi Gravity Gun for small scale repair work.
SRI Pro Micro has lighter trigger control allowing for greater control for Micro repairs.
New lightweight SRI Pro for improved handling.
Ergonomic gun body with improved fit, feel, comfort and control.
Balanced air valve design for precision control of paint and air.
Different air cap choices to suit all latest refinishing materials.
A range of tip sizes for varying viscosities and control preferences.
Renowned DeVilbiss atomisation quality and even paint distribution.
art Number Explanation
P
SRiPROL - TE5 - 08
SRiPROM -MC1 - 06M
Model
Air Cap
Fluid Tip
Specification
Air Consumption:
HV5: 135 l/min (4.8 cfm) @ 2.0 bar (30 psi)
TE5: 100 l/min (3.5 cfm) @ 2.0 bar (30 psi)
RS1: 55 l/min (1.9 cfm) @ 1.0 bar (15psi)
MC1: 50 l/min (1.8 cfm) @ 1.0 bar (15psi)
SRi Pro MICRO only
Air inlet thread
1/4” Universal
Cup Capacity
125 mls
Weight (gun & cup)
455 gms
Air cap & ring
Plated Brass
Fluid Tip
Stainless Steel
Needle
Stainless Steel
No TE5
High Efficiency
Air Cap
No HV5
HVLP Air Cap
No MC1
High Efficiency
Air Cap
SRi Pro Gravity Spot Repair Spray Gun Kits (Specify the air cap & tip size required)
Part No
Description
SRIPROL-TE5-08
Gravity Feed Gun with TE5 High Efficiency air cap & No. 08 fluid tip
SRIPROL-HV5-10
Gravity Feed Gun with HV5 HVLP air cap & size No. 10 fluid tip
SRIPROM-MC1-06
Gravity Feed Gun with MICRO air cap & size No. 06 fluid tip
The kit contains: a spray gun with chosen cap tip set up, gravity cup, pouring funnel, spanner, torx key and cleaning brush.
Accessories
10
Part No
Description
SRIPRO-102-HV5-K
HVLP Air Cap and retaining ring
SRIPRO-102-TE5-K
High-Efficiency Air Cap and retaining ring
SRIPRO-102-MC1-BL-K
High-Efficiency Micro Air Cap and retaining ring
SRIPRO-102-RS1-K
Round spray (hornless) cap - priming, pinstriping
SRIPRO-200-**-K
Fluid Tip - Sizes No. 08, No. 10, No. 12 & No. 14
SRIPRO-210-06M-K
Fluid Tip - Micro only
SRIPRO-300-08-10-K
Fluid Needle for No. 08 & No. 10 fluid tip
SRIPRO-300-12-14-K
Fluid Needle for No. 12 & No. 14 fluid tip
SRIPRO-310-06M-K
Fluid Needle - Micro only
SPN-8-K2
Torx & flat blade Screwdriver - Trigger & Needle Packing
MPV-60-K3
Male Quick Detach Uni Swivel - fits to gun air inlet
SRi-65-K2
Pack of two cleaning brushes
PRO-415-1
SRi service kit – includes seals, packing and springs
SRi-510
125ml Acetal gravity cup
SRi-51-K12
Pack of 12 SRi cup pouring funnels
SRi-478-K12
Pack of 12 SRi Gravity Cups & 12 coloured lids
SRi-42-K3
Pack of 3 cone filters
DGIPRO-502-BAR
Digital Gauge - Reads in bars
SRIPRO-102-RS1-K
SPN-8-K2 &
SRi-50-K2
MPV-60-K3
DGiPRO-502-BAR
Catalogue 2015
NEW
201FOR
5
PRO-415-1 Repair Kit includes:
Separator(Kit of 5)
Body Bushing & Seal
Needle Spring
Needle Spring Pad
Spreader Valve Seal
Packing, Spring & Packing Nut Kit
Trigger Stud Screw (T20 Torx)
Trigger Stud
Valve Pin
SRIPRO-2K
SN-404-K
-
Ref. Description
No
Part No.
1
HVLP Air Cap & Ring
SRIPRO-102-HV5-K
High Efficiency Air Cap & Ring
SRIPRO-102-TE5-K
Ref. Description
No
Part No.
Round Spray Air Cap & Ring
SRIPRO-102-RS1-K
10
Stud and Screw kit
SN-405-K5
High Efficiency Micro Air Cap & Ring
SRIPRO-102-MC1-BL-K
11
Trigger, Stud & Screw Kit
SN-42-K
Fluid Tip (** = 08, 10, 12 or 14)
SRIPRO-200-**-K
12
Air Inlet
SN-40-K
Fluid Tip (Micro only)
SRIPRO-210-06M-K
13
Colour ID Ring Kit (4 Colours)
SN-26-K4
3
Separator
SRIPRO-2-K5
14
Airflow Valve
PRO-408-K
4
Fluid Needle for No. 08 & No. 10 Fluid Tips SRIPRO-300-08-10-K
Airflow Valve (Micro)
PRO-408-BL-K
2
Fluid Needle for No. 12 & No. 14 Fluid Tips SRIPRO-300-12-14-K
15
Gravity Cup Kit
SRI-510
Fluid Needle for SRiPRO Micro
SRIPRO-310-06M-K
16
Filter
SRI-42-K3
Fluid Adjusting Knob
SN-81-K
17
Drip Check Lid (kit of 5)
GFC-2-K5
Fluid Adjusting Knob (Micro only)
SN-81-BL-K
18
Funnel kit of 12
SRI-51-K12
Spreader Valve Assembly
SRIPRO-402-K
19
Spanner kit of 2
SRI-50-K2
Spreader Valve Assembly (Micro only)
SRIPRO-402-BL-K
20
Torx Key
SPN-8-K2
7
Body Bushing & Seal
SN-6-K
21
Needle spring and pad kit
SN-423-K3
8
Packing, Spring & Packing Nut Kit
SN-404-K
22
Air valve seal & service tool
SN-34-K5
9
Air Valve Assembly
SN-402-K
23
Gravity Cup Lid
SRI-414-K2
5
6
Catalogue 2015
11
COMPLIANT SMART / SPOT REPAIR GRAVITY FEED
SPRAY GUN
Totally redesigned SRi gravity gun for small scale repair work.
Ergonomic gun body with improved fit, feel, comfort and control.
Balanced air valve design for precision control of paint and air.
Three compliant air cap choices to suit all latest refinishing materials.
A range of four tip sizes for varying viscosities and control preferences.
Renowned DeVilbiss atomisation quality and even paint distribution.
Faster, easier maintenance from user-friendly fittings and adjustments.
Rugged drop forged body with anodised finish for protection.
art Number Explanation
P
SRiPRO -
Model
TS1
-
Air Cap
08
Fluid Tip
Specification
Air Consumption:
HS1: 135 l/min (4.8 cfm) @ 2.0 bar (30 psi)
TS1: 100 l/min (3.5 cfm) @ 2.0 bar (30 psi)
No HS1
Air Cap HVLP
RS1: 55 l/min (1.9 cfm) @ 1.0 bar (15psi)
Air inlet thread
1/4” Universal
Cup Capacity
125 mls
Weight (gun & cup)
500 gms
Air cap & ring
Plated Brass
Fluid Tip
Stainless Steel
Needle
Stainless Steel
No TS1
Air Cap Trans Tech
SRi Pro Gravity Spot Repair Spray Gun Kits (Specify the air cap & tip size required)
Part No
Description
SRIPRO-TS1-08
Gravity Feed Gun with TS1 Trans-Tech cap & No. 08 fluid tip
SRIPRO-HS1-10
Gravity Feed Gun with HS1 HVLP cap & size No. 10 fluid tip
The kit contains: a spray gun with chosen cap tip set up, gravity cup, pouring funnel, spanner, torx key and cleaning brush.
SRIPRO-100-RS1-K
Accessories
12
Part No
Description
SRIPRO-100-HS1-K
HVLP Air Cap and retaining ring
SRIPRO-100-TS1-K
Trans-Tech Air Cap and retaining ring
SRIPRO-100-RS1-K
Round spray (hornless) cap - priming, pinstriping
SRIPRO-200-**-K
Fluid Tip - Sizes No. 08, No. 10, No. 12 & No. 14
SRIPRO-300-08-10-K
Fluid Needle for No. 08 & No. 10 fluid tip
SRIPRO-300-12-14-K
Fluid Needle for No. 12 & No. 14 fluid tip
SPN-8-K2
Torx & flat blade Screwdriver - Trigger & Needle Packing
MPV-60-K3
Male Quick Detach Uni Swivel - fits to gun air inlet
SRi-65-K2
Pack of two cleaning brushes
PRO-415-1
SRi service kit – includes seals, packing and springs
SRi-510
125ml Acetal gravity cup
SRi-51-K12
Pack of 12 SRi cup pouring funnels
SRi-478-K12
Pack of 12 SRi Gravity Cups & 12 coloured lids
SRi-42-K3
Pack of 3 cone filters
DGIPRO-502-BAR
Digital Gauge - Reads in bars
SPN-8-K2 &
SRi-50-K2
MPV-60-K3
DGiPRO-502-BAR
Catalogue 2015
PRO-415-1 Repair Kit includes:
Seal & Pin Kit (5 Pack)
Fluid Needle Spring (Sub Assy)
Needle Packing
Body Bushing Gasket
Trigger Stud
Sprayhead Gasket
Screw
Separator
GTI-428 K5
SN-409
SN-404
SN-8
SN-13
SN-18-1
SN-22
SRIPRO-2
Ref.
No
Description
Part No.
Ref.
No
Description
Part No.
1
HVLP Air Cap & Ring
SRIPRO-100-HS1-K
10
Stud and Screw kit
SN-405-K5
Trans-Tech Air Cap & Ring
SRIPRO-100-TS1-K
11
Trigger, Stud & Screw Kit
SN-42-K
Round Spray Air Cap & Ring
SRIPRO-100-RS1-K
12
Air Inlet
SN-40-K
2
Fluid Tip (** = 08, 10, 12 or 14)
SRIPRO-200-**-K
13
Colour ID Ring Kit (4 Colours)
SN-26-K4
3
Separator
SRIPRO-2-K5
14
Airflow Valve
PRO-404-K
4
Fluid Needle for No. 08 & No. 10 Fluid Tips SRIPRO-300-0810-K
15
Gravity Cup Kit
SRI-510
16
Filter
SRI-42-K3
17
Drip Check Lid (kit of 5)
GFC-2-K5
18
Funnel kit of 12
SRI-51-K12
19
Spanner kit of 2
SRI-50-K2
20
Torx Key
SPN-8-K2
21
Needle spring and pad kit
SN-4-K3
22
Air valve seal & service tool
SN-34-K5
23
Gravity Cup Lid
SRI-414-K2
Fluid Needle for No. 12 & No. 14 Fluid Tips SRIPRO-300-1214-K
5
Fluid Adjusting Knob, Spring & Pad Kit
PRO-3-K
6
Spreader Valve Assembly
SRIPRO-401-K
7
Body Bushing & Seal
SN-6-K
8
Packing, Spring & Packing Nut Kit
SN-404-K
9
Air Valve Assembly
SN-402-K
Catalogue 2015
13
GENERAL PURPOSE SPRAY GUN
Cost-effective i-system spray gun, for General Purpose applications around the
bodyshop.
Featuring the latest GTi Pro forged aluminium gun body with
lightweight aluminium controls, for that legendary fit and feel
synonymous with DeVilbiss ergonomics.
Fitted with the new GP1 High Efficiency air cap for perfect atomisation.
Ideal for a wide range of materials including enamels, synthetics, primers,
2 pack commercial paints as well as materials that demand high or fast application rates.
Available with a choice of 1.6mm or 1.8mm fluid tips, providing the flexibility required
for General Purpose duty.
art Number Explanation
P
GPi - GP1 - 18
Model
Air Cap
Fluid Tip
Specification
Air Inlet Pressure
2.0 bar (29psi)
Air Consumption
270 l/min (9.5cfm)
Air Inlet Thread
1/4” Universal
Fluid Flow
1.4 - 100-180
1.6 - 180-280
No GP1
High Efficiency Air Cap
1.8 - 200-350
Pattern
280-320 mm
Cup Capacity
560 mls
Weight (gun & cup)
683 gms
Air Cap & Ring
Plated Brass
Fluid Tip
Stainless Steel
Fluid Needle
Stainless Steel
GPi Spray Gun Kits
Part No
Description
GPI-GP1-14
Gravity gun & cup kit – GPI air cap & 1.4mm fluid tip
GPI-GP1-16
Gravity gun & cup kit – GPI air cap & 1.6mm fluid tip
GPI-GP1-18
Gravity gun & cup kit – GPI air cap & 1.8mm fluid tip
Accessories
Part No
Description
PRO-102-GP1-K
Air Cap
PROC-215-**-K
Fluid Tip
PRO-306-16-18-K
Needle
PRO-415-1
Spray Gun Service/Repair Kit
SN-406
Gun wrench, Torx & flat back screwdriver, cleaning brush and colour ID rings
HAV-501-B
In-Line Air Adjusting Valve
MPV-60-K3
Male Quick Detach Uni Swivel - fits to gun air inlet
HAF-507-K12
Lightweight in-line air filter (pack of 12)
4900-5-1-K3
Pack of three cleaning brushes
KGP-5-K5
Pack of 5 gravity cup filters for GFC cups
PRO-15-K3
ProClip - snap on trigger locking clip
GFV-50-F
Gravity Gun Stands
** = Fluid tip size
14
HAV-501-B
KGP-5-K5
GFV-50-F
MPV-60-K3
Catalogue 2015
PRO-415-1 Repair Kit includes:
Seal & Pin Kit (5 Pack)
Fluid Needle Spring (Sub Assy)
Needle Packing
Body Bushing Gasket
Trigger Stud
Sprayhead Gasket
Screw
Separator
Ref
No
Description
1
Air Cap Retaining Clip
2
3
Ref
No
Description
JGA-156-K5
13
Trigger, Stud & Screw Kit
SN-21-K
Air Cap
PRO-102-GP1-K
14
Air Valve Seal & Service Tool
SN-34-K5
Air Cap Retaining Ring & Seals
PRO-405-K
15
Air Inlet
SN-40-K
4
Fluid Tip – 14, 16, 18
PROC-215-**-K
16
Colour ID Ring Kit (4 Colours)
SN-26-K4
5
Spray Head Seal (kit of 2)
SN-18-1-K2
17
Airflow Valve
PRO-407-K
6
Spray Head & Seal Kit
SN-17-1-K
18
Baffle plate
SN-41-K
7
Body Bushing & Seal
SN-6-K
19
Gravity Cup Kit
GFC-501
8
Fluid Needle for No. 12 & No. 14 Fluid Tips
PRO-306-12-14-K
20
Drip Check Lid (kit of 5)
GFC-2-K5
Fluid Needle for No. 16 & No. 18 Fluid Tips
PRO-306-16-18-K
21
Gravity Cup Lid
GFC-402
9
Fluid Adjusting Knob
PRO-3
22
Filter
KGP-5-K5
10
Spreader Valve Assembly
PRO-406-K
23
Trigger Stud & Torx Screw (kit of 5)
SN-405-K5
11
Packing, Spring & Packing Nut Kit
SN-404-K
24
Needle spring and pad kit
SN-4-K3
12
Air Valve Replacement Kit
SN-402-K
25
Air valve seal & service tool
SN-34-K5
Catalogue 2015
Part Number
GTI-428 K5
SN-409
SN-404
SN-8
SN-13
SN-18-1
SN-22
SRIPRO-2
Part Number
15
PROFESSIONAL Conventional Gravity Feed Spray Gun
Totally redesigned GFG gun for professional use.
Renowned DeVilbiss atomisation quality and even paint distribution.
Air valve design for ultra smooth triggering and control.
Rugged drop forged body with anodised finish for protection.
A choice of two advanced technology air caps to suit solids and metallics.
Three fluid tip sizes for varying viscosities and control preferences.
Ergonomic gun body with improved fit, feel, comfort and control.
Faster, easier maintenance from user-friendly fittings and adjustments.
art Number Explanation
P
GFGPRO - C1 - XX
Model
Air Cap
Fluid Tip
No C1
Air Cap
No C2
Air Cap
Specification
Air Inlet Pressure
Air Consumption
Air Inlet Thread
C1: 2.5 - 3.0 bar (30 - 45 psi)
C2: 2.5 - 4.0 bar (30 - 60 psi)
C1: 300 l/min (10.6 cfm) @ 3.0 bar
C2: 305 l/min (12.8 cfm) @ 3.0 bar
1/4” Universal
Cup Capacity
Weight (gun & cup)
Air Cap & Ring
Fluid Tip
Fluid Needle
560 mls
768 gms
Plated Brass
Stainless Steel
Stainless Steel
DGIPRO-502-BAR
GFG-Pro Spray Gun Kits
When ordering please specify the air cap of your choice (C1 or C2) and the tip size of your choice (14, 16 or 18).
Part No Examples
GFGPRO-C1-14
GFGPRO-C1-16
GFGPRO-C2-18
Description
Gravity Gun & Cup - C1 air cap and No. 14 fluid tip
Gravity Gun & Cup - C1 air cap and No. 16 fluid tip
Gravity Gun & Cup - C2 air cap and No. 18 fluid tip
MPV-60-K3
Kit includes GFG PRO Gravity gun, cup, paint filter, brush and multi-fit spanner
Accessories
Part No
PROC-120-C1-K
PROC-120-C2-K
PROC-220-**-K
GFGPRO-320-K
PRO-415-1
SPN-8-K2
SN-406
DGIPRO-502-BAR
MPV-60-K3
HAF-507-K12
4900-5-1-K3
KGP-5-K5
PRO-15-K3
16
Description
C1 Air Cap and retaining ring
C2 Air Cap and retaining ring
Fluid Tip - Size Numbers 14, 16 & 18
Fluid Needle
Spray Gun Service/Repair Kit
Torx & flat blade Screwdriver - Trigger & Needle Packing
Gun wrench, Torx & flat back screwdriver, cleaning brush and colour ID rings
Digital Gauge - Reads in bars
Male Quick Detach Uni Swivel - fits to gun air inlet
Lightweight in-line air filter (pack of 12)
Pack of three cleaning brushes
Pack of 5 gravity cup filters for GFC cups
ProClip - snap on trigger locking clip
HAF-507-K12
PRO-415-1
** = Fluid tip size
Catalogue 2015
PRO-415-1 Repair Kit includes:
Seal & Pin Kit (5 Pack)
Fluid Needle Spring (Sub Assy)
Needle Packing
Body Bushing Gasket
Trigger Stud
Sprayhead Gasket
Screw
Separator
Ref
No
Description
1
Air Cap Retaining Clip
2
Ref
No
Description
JGA-156-K5
13
Trigger, Stud & Screw Kit
SN-21-K
C1 Aircap & Ring
PROC-120-C1-K
14
Air valve seal & service tool
SN-34-K5
C2 Aircap & Ring
PROC-120-C2-K
15
Air Inlet
SN-40-K
3
Air Cap Retaining Ring & Seals
PRO-405-K
16
Colour ID Ring Kit (4 Colours)
SN-26-K4
4
Fluid Tip
PROC-220-**-K
17
Airflow Valve
PRO-411-K
5
Spray Head Seal (kit of 2)
SN-18-1-K2
18
Baffle plate
SN-41-K
6
Spray Head & Seal Kit
SN-17-1-K
19
Gravity Cup Kit
GFC-501
7
Body Bushing & Seal
SN-6-K
20
Drip Check Lid (kit of 5)
GFC-2-K5
8
Fluid Needle
GFGPRO-320-K
21
Gravity Cup Lid
GFC-402
9
Fluid Adjusting Knob, Spring & Pad Kit
PRO-3-K
22
Filter
KGP-5-K5
10
Spreader Valve Assembly
PRO-402-K
23
Torx Key
SPN-8-K2
11
Packing, Spring & Packing Nut Kit
SN-404-K
24
Trigger Stud & Torx Screw (kit of 5)
SN-405-K5
12
Air Valve Replacement Kit
SN-402-K
25
Needle spring and pad kit
SN-4-K3
Catalogue 2015
Part Number
GTI-428 K5
SN-409
SN-404
SN-8
SN-13
SN-18-1
SN-22
SRIPRO-2
Part Number
17
FLG-5 General Purpose Spray Gun
General purpose compliant spray gun for a wide range of refinish paints and coatings.
®
Operates with unique and efficient DeVilbiss Trans-Tech Atomisation Technology.
Ergonomically shaped gun handle for positive grip and comfort.
Smooth action trigger with exceptionally light pull for fatigue free operation.
Ultra lightweight but strong, cast aluminium gun body.
Full controls of pattern shape, fluid flow rate and air inlet pressure.
Precision engineered brass air cap and stainless steel fluid tips.
Choice of gravity or suction models with large capacity cups.
NOT SUITABLE FOR USE WITH WATERBORNE MATERIALS.
art Number Explanation
P
FLG - G5 - 14
Model Gravity/Air Cap
Fluid Tip
Specification
Air inlet Pressure
2.0 bar (29 psi) – Suction & Gravity
Air Consumption
277 l/min (9.8 cfm)
Air Inlet Thread
1⁄4” Universal
Cup Capacity
Gravity 560 mls, Suction 1140 mls
Weight (gun & cup)
Gravity 642 gms, Suction 934 gms
Air Cap
Plated brass
Retaining Ring
Plated brass
Fluid Tip
Stainless Steel
Fluid Needle
Stainless Steel
FLG-5 Air Cap
FLG-5 Spray Gun Kit
Part No
Description
FLG-G5-14
Gravity Gun & Cup Kit – No 5 Air Cap & 1.4 mm Fluid Tip
FLG-G5-18
Gravity Gun & Cup Kit – No 5 Air Cap & 1.8 mm Fluid Tip
FLG-S5-18
Suction Gun & Cup Kit – No 5 Air Cap & 1.8 mm Fluid Tip
4900-5-1-K3
Spares and Accessories
18
Part No
Description
FLG-0001-5
No 5 Trans-Tech Air Cap (Fits Gravity & Suction)
SGK-0023
Air Cap Retaining Ring
SGK-0012-14
1.4 mm fluid tip for gravity gun
SGK-0012-20
2.0 mm fluid tip for gravity gun
SGK-0014-18
1.8 mm fluid tip for suction and gravity guns
SGK-0430-18
Fluid Needle (for 1.8 mm tip – Suction Gun)
SGK-0420
Fluid Needle (for 2.0 mm tip – Gravity Gun)
SGK-0418
Fluid Needle (for 1.8 mm tip – Gravity Gun)
SGK-0414
Fluid Needle (for 1.4mm - Gravity Gun)
SGK-0043-K10
Fluid Tip seal (pack of 10)
K-5030
Baffle Replacement Kit
K-5040
Repair kit – seals and springs – includes service tool
KGP-5-K5
Pack of gravity cup filters for GFC cup
MPV-60-K3
Male, quick detach, universal swivel – fits to gun air inlet
4900-5-1-K3
Pack of three cleaning brushes
KK-4584
Spray gun cleaning tool kit – purpose made brushes & tools
SGK-0537
Needle Packing
HAV-501-B
KK-4584
KGP-5-K5
Catalogue 2015
Ref
No
1
2
3
Description - Gravity Gun
Retaining ring
Air cap
Fluid tip 1.4mm, Fluid tip 1.8mm
Fluid tip 2.0mm (available
separately)
Gasket
Baffle
Packing
U-cup seal
Air-valve seat
Air-valve stem
Air-valve spring
Fluid needle 1.4mm
Fluid needle 1.8mm
Fluid needle 2.0mm (available
separately)
Filter
Lid assembly
Drip free vent lid kit of 5
Cup assembly
Assembly tool
4
5
6
7
8
9
10
11
12
13
14
15
16
*
Seal, baffle and gasket
replacement kit, items 4, 5, 6, 7,
8, 9, 10, and 16
Baffle replacement kit, items 4
and 5.
•
Part Number
SGK-0023
FLG-0001-5
SGK-0012-14
SGK-0014-18
SGK-0012-20
SGK-0043-K10* •
*•
*
*
*
*
*
SGK-0414
SGK-0418
SGK-0420
KGP-5-K5
GFC-402
GFC-2-K5
GFC-501
*
K-5040
K-5030
Ref
No
Description Suction Gun
1
Retaining ring
SGK-0023
2
Air cap
FLG-0001-5
3
Fluid tip 1.8mm
SGK-0014-18
4
Gasket
SGK-0043-K10* •
5
Baffle
*•
6
Packing
SGK-0337*
7
U-cup seal
*
8
Air-valve seat
*
9
Air-valve stem
*
10
Air-valve spring
*
11
Fluid needle 1.8mm
SGK-0430-18
12
Assembly tool
*
*
Seal, baffle and
gasket replacement
kit, items 4, 5, 6, 7,
8, 9, and 10
K-5040
•
Baffle replacement
kit, items 4 and 5
K-5030
Catalogue 2015
Part Number
19
GRAVITY FEED AIRBRUSH PERFORMANCE &
VERSATILITY FOR AUTOMOTIVE ARTISTS
Sprays most automotive paints and lacquers.
Hairline detail to high paint-flow shading and
gradual fades.
Lightweight, well balanced with smooth double
action trigger.
Crown cap standard for fine lines and needle
protection.
Copper, nickel and chrome plated body.
Pre-set handle for precise control of paint flow.
Removable 9 mls (1/3rd oz) gravity cup.
Solvent proof fluid passages, PTFE needle packing.
Part Number
DGR - 501G - 35
Precision made and hand tested in the U.S.A.
Specification
Operating Pressure
1.3 – 3.5 bar (20 -50 psi)
Max inlet pressure
12 bar (175 psi)
Fluid tip
0.35mm
Cup Capacity
9 mls (1/3 fl/oz)
Airbrush plating
Nickel, copper, chrome
Needle Packing
PTFE (solvent proof)
Hose: Inside diameter
3.2 mm (1/8”)
Air Hose connection
1⁄4” NPS (M)
Universal fluid threaded connector
3/8”
DAGR Airbrush Kit and Accessories
20
Part No
Description
DGR-501G-35
DAGR Gravity Airbrush - 0.65mm – 9 CC Cup/lid (1/3 fl/oz)
DGR-123
3m (10’) Braided Nylon Air Hose with loose nut 1⁄4” swivel connections.
DGR-121K
Repair Kit - ‘O’ Rings, needle spring and washers
DGR-124
3m (10’) Braided Air Hose with QD
DGR-127
Quick Disconnect Kit
Catalogue 2015
Ref.
No.
Description
Part No.
Ref.
No.
Description
Part No.
1
Crown cap
DGR-101
14
Spring guide
DGR-111
2
Air cap (for .35mm Tip)
DGR-103-35
15
Needle locknut
DGR-112
3
Head cap
DGR-104
16
Needle (for .35mm tip)
DGR-113-35
4
Tip (.35mm)
DGR-105-35
17
Cutaway handle w/pre-set
DGR-114
*5
O-ring (head cap & handle)
-
* 18
O-ring (pre-set needle knob)
-
6
Packing and nut assembly (PTFE)
DGR-106K
19
Pre-set needle knob
DGR-116
7
Air valve casing
DGR-107
20
1/4 oz. (7 cc) cup and lid
DGR-117
1/3 oz. (9 cc) cup and lid (standard)
DGR-118
8
Air valve kit
DGR-108K
21
*9
Air valve washer
-
22
1/2 oz. (14 cc) cup and lid
DGR-119
Cup lid
DGR-120
10
Trigger assembly
DGR-109
23
11
Trigger buttons ergo-pack (4 types)
DGR-122K
Repair Kit
12
Needle guide, rocker, & spring
DGR-110K
* 13
Needle spring
-
Catalogue 2015
DAGR repair kit - includes item numbers 5, 9,
13 & 18
DGR-121K
21
COMPLIANT Suction & PRESSURE Feed Spray GunS
Totally redesigned GTi Pro gun for suction or pressure feed duty. Ergonomic gun body with improved fit, feel, comfort and controls.
Suitable for use with a suction cup or pumps, tanks or remote feed cups.
Four compliant air cap choices to suit solids, metallics, bases and clears.
A range of pressure & suction tip sizes for varying viscosities and control preferences.
Balanced air valve design for ultra smooth triggering and control.
Renowned DeVilbiss atomisation quality and even paint distribution.
Faster, easier maintenance from user-friendly fittings and adjustments.
Rugged drop forged body with anodised finish for protection.
art Number Explanation
P
GTISPRO (or GTIPPRO) - T1 - XX
Model
No H1 HVLP
Air Cap
Air Cap
No T1 Trans-Tech
Air Cap
Fluid Tip
No T2 Trans-Tech
Air Cap
No T4 Trans-Tech
Air Cap
GTiP-Pro only
Specification
Air Inlet Pressure
H1, T1, T2, T3 & T4 air caps 2.0 bar (30 psi)
Fluid inlet thread
Universal 3/8” BSP/NPS
Air Consumption
H1: 450 l/min (16 cfm) @ 2.0 bar (30 psi)
Max static air inlet pressure
P1 = 12 bar (175 psi)
 
T1: 280 l/min (10 cfm) @ 2.0 bar (30 psi)
Max static fluid inlet pressure
P2 = 14 bar (203 psi)
 
T2: 350 l/min (12 cfm) @ 2.0 bar (30 psi)
Air cap & ring
Plated Brass
 
T4: 330 l/min (11.7 cfm) @ 2.0 bar (30 psi)
450 l/min (15.9 cfm) @ 3.0 bar (44 psi)
Fluid Tip & Needle
Stainless Steel
Suction gun & cup weight
1070 gms
Universal 1/4” BSP/NPS
Pressure gun weight
650 gms
Air inlet thread
DGIPRO-502-BAR
GTi Pro Suction / Pressure Spray Gun Kits
When ordering please specify the air cap and tip size required.
Part No Examples
Description
GTISPRO-T1-16
Suction Feed Gun with T1 air cap and No. 16 fluid tip
GTIPPRO-T2-085
Pressure Feed Gun with T2 air cap and No. 085 fluid tip
MPV-60-K3
GTI Pro kits include: suction cup with filter (suction kits only), cleaning brush, torx key, set of 4 identification rings and
combination spanner
Accessories
22
Part No
Description
PRO-100-H1-K
HVLP Air Cap and retaining ring
PRO-100-T1-K
Trans-Tech Air Cap and retaining ring
PRO-100-T2-K
Trans-Tech Air Cap and retaining ring
PRO-100-T4-K
Trans-Tech Air Cap and retaining ring
PRO-200-**-K
Suction/Pressure Fluid Tip - Size Numbers 16, 18 & 20
PRO-315-K
Suction/Pressure Fluid Needle for 16, 18 & 20 Tip sizes
PRO-205-**-K
Pressure Fluid Tip - Size Numbers 085, 10, 12 & 14
PRO-305-085-10-K
Pressure Fluid Needle for 085 & 10 Tip sizes
PRO-305-12-14-K
Pressure Fluid Needle for 12 & 14 Tip sizes
PRO-415-1
Spray Gun Service/Repair Kit
SPN-8-K2
Torx & flat blade Screwdriver - Trigger & Needle Packing
DGIPRO-502-BAR
Digital Gauge - Reads in bars
MPV-60-K3
Male Quick Detach Uni Swivel - fits to gun air inlet
HAF-507-K12
Lightweight in-line air filter.
4900-5-1-K3
Pack of three cleaning brushes
VSA-512
Strainer Assembly
KR-484-K10
PRO-415-1
HAF-507-K12
** = Fluid tip size
Catalogue 2015
PRO-415-1 Repair Kit includes:
Seal & Pin Kit (5 Pack)
Fluid Needle Spring (Sub Assy)
Needle Packing
Body Bushing Gasket
Trigger Stud
Sprayhead Gasket
Screw
Separator
GTI-428 K5
SN-409
SN-404
SN-8
SN-13
SN-18-1
SN-22
SRIPRO-2
Ref.
No.
Description
Part No.
Ref.
No.
Description
Part No.
1
Air Cap Retaining Ring
PRO-405-K
15
Trigger, Stud & Screw Kit
SN-21-K
2
Air Cap Retaining Clip
JGA-156-K5
16
Air Inlet
SN-40-K
3
Aircap & Ring
See page 22
17
Colour ID Ring Kit (4 Colours)
SN-26-K4
4
Fluid Tip
See page 22
18
Airflow Valve
PRO-411-K
5
Baffle Plate
SN-41-K
19
Stud and Screw kit
SN-405-K5
6
Spray Head Seal (kit of 2)
SN-18-1-K2
20
Torx Key
SPN-8-K2
7
Spray Head & Seal Kit
SN-17-1-K
21
Fluid Inlet Connector Kit
PRO-12-K
8
Body Bushing & Seal
SN-6-K
22
Cup Lid Assembly
KR-4001-B
9
Fluid Needle
See page 22
23
Lid Gaskets - kit of 3
KR-11-K3
10
Fluid Adjusting Knob, Spring & Pad Kit
PRO-3-K
24
Drip Free Diaphragms - Kit of 5
KR-115-K5
11
Spreader Valve Assembly
PRO-404-K
25
Cup Only
KR-466-K
12
Packing, Spring & Packing Nut Kit
SN-404-K
26
Complete Cup Assembly
KR-566-1-B
13
Air Valve Seal
SN-34-K5
27
Needle spring and pad kit
SN-4-K3
14
Air Valve Assembly
SN-402-K
Catalogue 2015
23
COMPLIANT SUCTION & PRESSURE FEED SPRAY GUNS
The lightweight gun, redesigned for suction or pressure feed duty.
Ergonomic gun body design with even better fit and balance for comfort and control.
A range of pressure & suction tip sizes for varying viscosities and control preferences.
Four compliant air cap choices to suit all materials and coatings.
Utilises coaxial air valve design for ultra-smooth triggering and control.
Renowned DeVilbiss atomisation quality and even paint distribution.
Faster, easier maintenance from user-friendly fittings and adjustments.
art Number Explanation
P
PROSL - TE10 - 18
Model
Air Cap Fluid Tip
TE10 High Efficiency
Air Cap
TE20 High Efficiency
Air Cap
Specification
Air Inlet Pressure
Air Consumption
Air Inlet Thread
Fluid Inlet Thread
Max Static air inlet pressure
Max Static fluid inlet pressure
2.0 bar (29psi)
TE10: 270 l/min (9.5 cfm)
TE20: 360 l/min (12.7 cfm)
TE30: 365 l/min (12.9 cfm)
TE40: 350 l/min (12.4 cfm)
Universal 1/4” BSP/NPS
Universal 3/8” BSP/NPS
P1 = 12 bar (175 psi)
P2 = 15 bar (215 psi)
TE30 High Efficiency
Air Cap
TE40 High Efficiency
Air Cap
(Pressure only)
(Pressure only)
Suction Cup Capacity
Weight (gun only)
Weight (gun & suction cup)
Air Cap
Air Cap Retaining Ring
Fluid Tip
Fluid Needle
1 litre
490 gms
925 gms
Plated Brass
Clear Anodised Aluminium
Stainless Steel
Stainless Steel
DGIPRO-502-BAR
GTi Pro LITE Spray Gun Kits
When ordering please specify the air cap of your choice and the tip size of your choice.
Part No Examples
PROSL-TE10-16
PROPL-TE40-10
Description
Suction gun & cup kit with TE10 High Efficiency air cap & #16 fluid tip
Pressure gun kit with TE40 High Efficiency air cap & #10 fluid tip
GTI Pro LITE kits include: suction cup with filter (suction kits only), cleaning brush, torx key, set of 4 identification rings and combination spanner
MPV-60-K3
Accessories
24
Part No
PRO-102-TE10-K
PRO-102-TE20-K
PRO-102-TE30-K
PRO-102-TE40-K
PRO-200-**-K
PRO-205-**-K
PRO-325-K
PRO-320-085-10-K
PRO-320-12-14-K
PRO-470
SN-406
DGIPRO-502-BAR
MPV-60-K3
HAF-507-K12
4900-5-1-K3
Description
TE10 High Efficiency Air Cap and retaining ring
TE20 High Efficiency Air Cap and retaining ring
TE30 High Efficiency Air Cap and retaining ring
TE40 High Efficiency Air Cap and retaining ring
Fluid Tip – Suction feed - Size Numbers 16, 18 & 20
Fluid Tip – Pressure feed – Size Numbers (085, 10, 12 & 14)
Suction Fluid Needle for 16, 18 & 20
Pressure Fluid Needle for 085 & 10 tip sizes
Pressure Fluid Needle for 12 & 14 tip sizes
Spray Gun Service/Repair Kit
Gun wrench, Torx & flat back screwdriver, cleaning brush and colour ID rings
Digital gauge for air inlet fitting - Reads in bars
Pack of three male quick detach uni swivel - fits to gun air inlet
Lightweight in-line air filter (pack of 12)
Pack of three cleaning brushes
VSA-512
Strainer Assembly
HAF-507-K12
PRO-470
**** = Air Cap
** = Fluid tip size
Catalogue 2015
PRO-470 Repair Kit includes:
Packing, Spring & Packing Nut
SN-404
Trigger Stud & Screw*
Spray Head Seal
SN-18-1
Seal and Pin Kit
GTI-428-K5
Needle Spring
PRO-472
*Not sold separately
Ref
No
Description
Part Number
Ref
No
Description
Part Number
1
Air Cap Retaining Ring & Seal
PRO-420-K
14
Air Inlet Kit
SN-9-K
2
Air Cap Retaining Clip
JGA-156-K5
15
Packing, spring and packing nut kit
SN-404-K
3
High Efficiency Aircap & Ring
See Page 24
16
Trigger, stud & Screw Kit
SP-617-CR-K
4
Fluid Tip Kit
See Page 24
17
Airflow valve
PRO-407-K
5
Spray Head Seal
SN-18-1-K2
18
Circlip - kit of 5
25746-007-K5
6
Spray Head Kit
SN-69-K
19
Fluid inlet kit
ADV-7-K
Suction Cup Models only
7
Spreader Valve Assembly
PRO-408-K
8
Air Valve Kit
PRO-471
20
Suction cup kit
KR-566-1-1B
9
Fluid Needle
See Page 24
21
Cup lid gasket - kit of 3
KR-11-K3
10
Housing
SN-66-K
22
Drip check Diaphragm (kit of 5)
KR-115-K5
11
Fluid Adjusting Knob
SN-67-C-K
23
Filter - kit of 10
KR-484-K10
12
Colour ID Ring Kit (4 Colours)
SN-26-K4
24
Lid assembly
KR-4001-B
13
Needle spring kit
PRO-472-K3
25
Cup
KR-466-K
Catalogue 2015
25
PROFESSIONAL Conventional Suction &
PRESSURE Feed Spray Gun
Totally redesigned JGA gun for professional use.
Renowned DeVilbiss atomisation quality and even paint distribution.
Balanced air valve design for ultra smooth triggering and control.
Rugged drop forged body with anodised finish for protection.
A choice of three advanced technology air caps to suit solids and metallics.
Three fluid tip sizes for varying viscosities and control preferences.
Ergonomic gun body with improved fit, feel, comfort and control.
Faster, easier maintenance from user-friendly fittings and adjustments.
art Number Explanation
P
JGASPRO (or JGAPPRO) - C1 - XX
Model
Air Cap
Fluid Tip
No C2 Air Cap
No C1 Air Cap
No C3 Air Cap
Specification
Air Inlet Pressure
Air Consumption
Air Inlet Thread
C1: 2.5 - 3.0 bar (30 - 45 psi)
C2: 2.5 - 4.0 bar (30 - 58 psi)
C3: 2.5 - 4.0 bar (30 - 58 psi)
C1: 300 l/min (10.6 cfm) @ 3.0 bar
C2: 305 l/min (12.8 cfm) @ 3.0 bar
C3: 410 l/min (14.5 cfm) @ 3.0 bar
1/4” Universal
Fluid Inlet Thread
Cup Capacity
Weight (gun & cup, S)
Weight (gun, P)
Air Cap & Ring
Fluid Tip
Fluid Needle
3/8” Universal
1000 mls
1070 gms
650 gms
Plated Brass
Stainless Steel
Stainless Steel
JGA-Pro Spray Gun Kits
When ordering please specify the air cap (C1, C2 or C3) and the tip size of choice (12, 14, 16, 18 or 085).
Part No Examples
JGASPRO-C1-16
JGAPPRO-C3-085
Description
Suction Feed Gun with C1 air cap and No. 16 fluid tip
Pressure Feed Gun with C3 air cap and No. 085 fluid tip
DGIPRO-502-BAR
JGA Pro kits include: suction cup with filter (suction kits only), cleaning brush, torx key, set of 4 identification rings and
combination spanner
Accessories
26
Part No
PROC-120-C1-K
PROC-120-C2-K
PROC-120-C3-K
PROC-220-**-K
JGAPRO-330-K
PROC-230-**-K
PRO-305-085-10-K
PRO-305-12-14-K
PRO-415-1
SPN-8-K2
SN-406
DGIPRO-502-BAR
MPV-60-K3
HAF-507-K12
4900-5-1-K3
KR-484-K10
Description
C1 Air Cap and retaining ring
C2 Air Cap and retaining ring
C3 Air Cap and retaining ring
Suction Fluid Tip - Size Numbers 16 or 18
Suction Fluid Needle for 14, 16 or 18 Fluid Tips
Pressure Fluid Tip - Size Numbers 085, 10, 12 or 14
Pressure Fluid Needle to match 085 & 10 Tip sizes
Pressure Fluid Needle to match 12 & 14 Tip sizes
Spray Gun Service/Repair Kit
Torx & flat blade Screwdriver for - Trigger & Needle Packing
Gun wrench, Torx & flat back screwdriver, cleaning brush and colour ID rings
Digital Gauge - Reads in bars
Male Quick Detach Uni Swivel - fits to gun air inlet
Lightweight in-line air filter.
Pack of three cleaning brushes
Pack of 10 suction cup paint strainers
VSA-512
Strainer Assembly
MPV-60-K3
KR-484-K10
PRO-415-1
** = Fluid tip size
Catalogue 2015
PRO-415-1 Repair Kit includes:
Seal & Pin Kit (5 Pack)
Fluid Needle Spring (Sub Assy)
Needle Packing
Body Bushing Gasket
Trigger Stud
Sprayhead Gasket
Screw
Separator
GTI-428 K5
SN-409
SN-404
SN-8
SN-13
SN-18-1
SN-22
SRIPRO-2
Ref.
No.
Description
Part No.
Ref.
No.
Description
Part No.
1
Air Cap Retaining Ring
PRO-405-K
15
Trigger, Stud & Screw Kit
SN-21-K
2
Air Cap Retaining Clip
JGA-156-K5
16
Air Inlet
SN-40-K
Colour ID Ring Kit (4 Colours)
SN-26-K4
Airflow Valve
PRO-411-K
3
Aircap & Ring
See page 26
17
4
Fluid Tip
See page 26
18
5
Baffle Plate
SN-41-K
19
Stud and Screw kit
SN-405-K5
6
Spray Head Seal (kit of 2)
SN-18-1-K2
20
Torx Key
SPN-8-K2
7
Spray Head & Seal Kit
SN-17-1-K
21
Fluid Inlet Connector Kit
PRO-12-K
8
Body Bushing & Seal
SN-6-K
22
Cup Lid Assembly
KR-4001-B
9
Fluid Needle
See page 26
23
Lid Gaskets - kit of 3
KR-11-K3
10
Fluid Adjusting Knob, Spring & Pad Kit
PRO-3-K
24
Drip Free Diaphragms - Kit of 5
KR-115-K5
11
Spreader Valve Assembly
PRO-404-K
25
Cup Only
KR-466-K
12
Packing, Spring & Packing Nut Kit
SN-404-K
26
Complete Cup Assembly
KR-566-1-B
27
Needle spring and pad kit
SN-4-K3
13
Air Valve Seal
SN-34-K5
14
Air Valve Assembly
SN-402-K
Catalogue 2015
27
SLG-620 GENERAL PURPOSE BUDGET SPRAY GUN
General purpose gravity feed compliant spray gun.
Lightweight and strong aluminium construction.
Smooth fluid flow and pattern shape controls.
Ergonomically shaped handle for postitive grip.
Precision engineered brass air cap provies excellent atomisation
of most popular compliant automotive refinish materials.
Fitted with a tough Acetal 550ml cup.
The kit includes: a removable paint filter, a cleaning brush and universal spanner for
easy cleaning and maintenance
Specification
28
Air Inlet Pressure
2.0 Bar
Air Consumption
250 l/min (8.8 cfm)
Air Inlet Thread
1/4” Universal
Cup Capacity (gravity)
550ml
Weight (gun & cup)
Gun 480g / Cup 160g
Air Cap
Brass - Nickel Plated
Retaining Ring
Anodised Aluminium
Fluid Tip
Stainless Steel
Fluid Needle
Stainless Steel
Part No
Description
SLG-620-13
Gravity Gun with 1.3mm fluid tip
SLG-620-18
Gravity Gun with 1.8mm fluid tip
SLG-450
Gravity Cup and Lid
Catalogue 2015
Pro Clean Gun Wash Cleaning Machine
Faster, cleaner and more efficient than conventional gun
wash machines.
Can be used for waterborne and solvent applications.
Significantly reduces solvent use and wastage
dramatically reducing gun cleaning costs.
Fresh solvent is used every time ensuring no
contamination and rapid colour changes.
The compact unit can be wall mounted to maximise
floor space in the mix room.
500ml colour coded waterborne and solvent aerosols
are easily clipped in and out of the machine.
One 500ml can will clean up to 32 spray guns.
Part Number: DEV-FHAZ1006
Specification
Dimensions
H: 900 mm
W: 245 mm
D: 275 mm
Weight
9 kg
Max Air Pressure
8 bar (116 psi)
Min Air Pressure
6 bar (86 psi)
ATEX Safety Approval
CE Ex II 3G c IIA T6
Pro Clean Gun Wash Machine
Part No
Description
DEV-FHAZ1006
Complete Pro Clean unit
DEV-FHFZ1004
Pro Clean Waterborne Aerosol
DEV-FHFZ1013
Pro Clean Solvent Aerosol
SAVE TIME:
Less than a minute for a completely clean spray gun
SAVE COST:
One 500ml can of cleaner will clean up to 32 spray guns
SAVE SPACE:
Can be wall mounted to keep the floor space clear
SAVE WASTE:
Highly efficient, less than 16 ml of cleaning solution to clean
a gun
Catalogue 2015
29
Stainless steel masking stencil to prevent
rub-through when sanding or shaving
minor surface imperfections
Ideal for:
Paint and lacquer runs.
Imperfections.
Minimising area when
sanding paint-filled chips or
scratches.
Advantages:
Stainless steel 304 provides
hardness for re-use.
Chemically etched shapes
eliminates burred edges.
Choice of four stencil shapes.
Specification
Dimensions
H: 100 mm
D: 90 mm
W: 1 mm
Weight
13g each
Shim Mask
30
Part No
Description
SHIM-3
Pack of three stainless steel shim
masks
Catalogue 2015
DMG Air Dryer Guns and Systems
A versatile system to speed up the drying process.
DMG guns multiply their intake by a factor of 7 to give generous air volumes.
A fully adjustable aerodry stand provides full dryer flexibility.
Solvent resistant for cleaning in gun wash machines.
DMG guns feature intake debris filters and shut-off valves.
Specification
Air consumption per gun at 3.4 bar (50psi)
325 l/min (11.5cfm)
Recommended working pressure range
2-4 bar (30 – 60 psi)
Noise level at 3.4 bar (50psi)
83 dba
DMG Air Dryer Systems
Part No
Description
DMG-501-K
Single Air Dryer gun – boxed
DMG-620
Two gun stand system with hose
Accessories
Part No
Description
DMG-5-K3
Pack of 3 dryer inlet filters
DMG-520-K
Air dryer stand and hose
H-6086-B
10m Air hose with female quick detach and swivel/loose nut fittings
MPV-424
Female, self sealing, QD air line fitting
MPV-5
Male stem, QD air line fitting with 1/4” BSP (F)
Ref No
Description
Part Number
1
Single Air Dryer Gun
DMG-501-K
2
Female QD
MPV-424
3
Filter pack of 3
DMG-5-K3
Catalogue 2015
31
Perfectly positioned for easy checking.
Accurate digital “bar” read-out of working pressure.
Retrofits to GTi Pro or PRi Pro gravity guns.
Optimise your gun performance as you work.
Accurate readings to within 0.05 bar (0.7 psi).
Fully ATEX Approved – totally gun washer safe.
DGIPRO-503-BAR-K
(For GTi Pro)
Air flow “cheater” valve adjusts the gauge.
Fitted in minutes - replaces standard spreader valve.
DGIPRO-504-BAR-K
(For GTi Pro LITE)
Digital air pressure gauge and control valve.
Resolution steps in increments of 0.05 bar.
Ultra smooth action control valve.
Fits directly to gun air inlet.
1/4“ Universal threads – swivel nut at outlet.
Fully ATEX Approved – totally gun washer safe.
Fits in line or directly onto tools and supply lines.
Very tough to withstand bodyshop duty.
DGIPRO-502-BAR
Lasts many times longer than analogue dial units.
Specification
Air Connections (M & F)
1/4” Universal (BSP/NPS)
DGIPRO-503-BAR-K
DGi PRO pod gauge - Retrofit to GTI Pro guns
only
DGIPRO-504-BAR-K
DGi PRO pod gauge - Retrofit to GTI Pro LITE
guns only
DGI Pro Air inlet gauge & adjusting valve
Accuracy
+ or – 1%
Resolution steps
0.05 bar (0.7 psi)
Max static inlet pressure
12 bar (175 psi)
DGIPRO-502-BAR
Housing
Die cast aluminium, nickel/chrome
plated.
Spare parts
Readout window
Toughened glass
SN-52-K5
DGI Pro adjusting valve seals
CE Ex 11 1G EEx ia IIC T4
MPV-60-K3
Male quick detach swivel
SN-57-K5
Air inlet aperture inserts
ATEX safety approval
32
Part numbers
Catalogue 2015
DISPOSABLES: US PATENT NOS. 6,820,824 AND 7,374,111 OWNED BY 3M INNOVATIVE PROPERTIES CO.
ADDITIONAL US PATENTS: NOS. 7,353,964; 7,344,040; 7,086,549
EUROPEAN PATENT NO. 0 954 381 B2 OWNED BY 3M INNOVATIVE PROPERTIES CO.
RE-USABLES: U.S. PATENT NOS. 6,820,824 AND 7,374,111 OWNED BY 3M INNOVATIVE PROPERTIES CO.
ADDITIONAL U.S. PATENTS: NOS. 7,380,680; 7,354,074; 7,353,964; 7,350,418; 7,344,040; 7,263,893;
7,165,732; 7,086,549.
DEKUPS DISPOSABLE PAINT CUPS SYSTEMS
Stable and positive cup to gun location.
Consistent paint flow, reduced risk of spray performance changes.
Practical 710cc size gives ideal weight to quantity ratio.
Choice of disc filters for waterborne basecoats or washable stick filters for
clears and primers.
Supplied in convenient wall mounting dispenser packs.
Lightweight gun adaptor with spiral lock mechanism.
No threads on outer cup lids to get contaminated and stubborn.
Storage plugs for liners supplied in the kit.
Funnels for liner top ups and gun flushing bottles available.
Part No
Description
DPC-601
DeKups disposable cup system kit – 32 disposable liners,
32 disposable lids
DPC-606
Reusable lid and sleeve kit
DPC-602
9oz. disposable lids & liners
DPC-607
9oz. re-usable lid & sleeve kit
DPC-607
Part No
Description
Part No
Description
DPC-10
Adaptor for SATA NR 2/3000, RP, KLC, MCB &
Jet 90 series & Sata 96719
DPC-42-K20
Disc Filet Kit – 125 micron filter screen
DPC-27-K10
Stick Filter – 200 micron filter screen
DPC-65-K24
9.oz 125 micron Disc Filter (24 Pack)
DPC-6-K10
Plug Kit (Pack Of 10)
DPC-22-K3
Disposable funnel
DPC-8-K2
Cleaning Bottle
DPC-60-K10
9oz. Measuring Guide (10 Pack)
DPC-62-K10
Measuring guide 2:1 & 3:1
DPC-63-K10
Measuring guide 4:1 & 5:1
DPC-11
Adaptor for SATA NR95, Iwata LPH-400 &
W400LV
DPC-13
Adaptor for Sagola (DeKup)
DPC-23
Adaptor 9oz – for SRI PRO
DPC-502
Adaptor for SATA Minijet QCC
DPC-78
Adaptor For Iwata Supernova
DPC-80
Adaptor for DeVilbiss Pro LITE, GTi, PRI, GFG,
Binks M1G, Sharpe Cobalt, Platinum & Titanium
DPC-501
Adaptor for SATA QC
Catalogue 2015
33
Dirt Control Floor Coat
Benefits
Reduces airborne particles in the spray booth by over 50% and traps them on
the floor.
Significantly reduces de-nibbing and polishing time caused by dirt in the paint job.
Significantly reduces dust and dirt in the booth.
Perfect for portable/smart repair booths.
Easy To Use
Fast and easy once-a-day application using a pump sprayer.
Simply sweep up the dirt and overspray with a broom and apply
Dirt Control Floor Coat.
One 5 US gallon bucket should provide approximately 20
applications.
Innovative
Floor Coat neutralises particles’ electrical charge, allowing them to stick
together.
Traps particles on the floor, not on the vehicle.
Water-based, low VOC.
Part Number
Description
DC-FC-5
Dirt Control Floor Coat (5 US gals)
DC-PS-1
DeVilbiss Floor Coat Pump Sprayer
OVERALLS
Benefits
Built in hood with pull cords.
Vented under arm and back.
Front and rear pockets with Velcro fastening.
Elasticated waistband and cuffs for improved fit and operator comfort.
Front knee pockets with Velcro fasteners for insertion of kneeling pads.
Full length zip front fastening.
Anti Static.
Lint Free.
Lightweight and comfortable to wear.
Reusable.
Washable.
34
Part Number
Description
DC-OV-M
Medium overall
DC-OV-L
Large overall
DC-OV-XL
Extra large overall
DC-OV-XXL
Extra extra large overall
Catalogue 2015
NEW F0R 2015
THE HIGH EFFICIENCY CONSUMABLES RANGE by
ANTI-STATIC WIPE
Single-use treated wipe to eliminate static between refinish coats.
Benefits
Reduces dirt imperfections on plastic parts caused by static.
Lint free.
No VOCs.
Easy To Use
Simply wipe over the entire panel before spraying.
Innovative
Improved metallic orientation from reduction of static charges which can cause metallics to
orientate incorrectly.
Directions For Use
NOTE: For best results, the wipe must make contact with entire surface to be sprayed. USE
DRY ONLY.
1) Carefully wipe the entire surface to be sprayed with the DeVilbiss CLEAN™ Anti-Static
Wiper.
2) For best results, use even, firm, overlapping strokes as if you were spraying the surface.
Part Number
Description
DC-ASW-K12
Box of 12 individually packed Anti-Static Wipers
BUMPER PREP PAD
Single-use pre-saturated scuff pad for new unprimed bumpers or plastic parts.
Benefits
Reduces steps in bumper preparation processes, increasing efficiency.
Provides comprehensive abrasion for better paint adhesion.
Removes water-based and oil-based contaminants.
Easy To Use
TM
DeVilbiss CLEAN Bumper Prep Pad cleans, abrades and degreases in
one easy step.
Simply soak in water to activate the pad and start prepping your bumper.
Innovative
The Bumper Prep Pad provides a more consistent scratch pattern and
greatly improves paint adhesion.
Additional preparation products may not be needed as the Bumper
Prep Pad cleans, abrades, and degreases in one easy step.
Catalogue 2015
Part Number
Description
DC-BPP-K12
Box of 12 individually packed Bumper Prep Pads
35
Gun supply hose swivels both radially and laterally, ensuring
better spray dynamics without the hose restricting the sprayers
movement.
Left or right sided waist belt fitment without having to change
the air fitting configuration.
The Pro Visor disperses breathing air gently around the
lightweight visor at a positive pressure with no misting or
discomfort, ensuring every sprayer can work at their best.
The wrap around visor provides excellent and much wider
peripheral vision than sprayers will be used to, while the
removable peak can help reduce glare from spray booth lighting.
Specification
Protection:
Carbon Filter Life:
Supply Pressure:
Air Flow Rate:
Noise level @ 160 l/min:
Approvals:
Zone Classifications:
APF = 40 / NPF = 200
3 months
4.0 bar (60 psi) minimum to 7.0 bar (100 psi) maximum
128 – 160 l/min (4.5 – 5.7 SCFM)
69.7 db
PPE directive 89/686/EEC. Conforms to EN 14594:2005 Class 3A
Suitable for use in Zones 1 and 2 Hazardous Areas (gas groups IIA
and IIB)
Pro Visor Outfit
PROV-600
Complete air fed visor outfit with waistbelt
Accessories
36
MPV-463
Part No
Description
PROV-20-K
Belt & regulator
PROV-21-K
Peak
PROV-22-K10
Peel off visors pack of 10
PROV-22-K50
Peel off visors pack of 50
PROV-23-K
Belt and buckle
PROV-25-K
Acetate visor face seal and air tube
PROV-26-K
Storage bag
PROV-27-K4
Filter element (pk 4)
PROV-28-K4
Comfort brow band (pk 4)
PROV-29-K
Visor head piece & breathing tube
PROV-30-K
Spacers & knobs (16 items - 1 set)
PROV-31-K
Filter cap & seal
PROV-32-K
Y-piece assembly
PROV-33-K
QD connector with reducer
PROV-406-K
Gun hose (1.2 m)
H-6085-QD
10 metre length air-hose complete with male and female QD’s
H-6065-B
10 metre length air hose complete with re-usable fittings.
MPV-424
Female self-sealing, QD air line fitting
MPV-10
Male-stem, QD air line fitting with 1/4” BSP (M)
MPV-5
Male-stem, QD air line fitting with 1/4” BSP (F)
MPV-462
Female self-sealing QD fitting with 1/4” BSP (F)
MPV-463
Kit of 4 QD’s fittings (2 male and 2 females)
PROV-21-K
PROV-27-K4
PROV-22-K10
MPV-60-K3
Catalogue 2015
Ref
No
Description
Part Number
Ref
No
Description
Part Number
1
Pro Visor complete unit
PROV-600
10
Comfort brow band (Pack 4)
PROV-28-K4
2
Belt & Regulator
PROV-20-K
11
Visor head piece & breathing air tube
PROV-29-K
3
Peak
PROV-21-K
12
Spacer, stud & knob (set of all sizes)
PROV-30-K
4
Tear-off visors pack of 10
PROV-22-K10
13
Filter cap & seal
PROV-31-K
Tear-off visors pack of 50
PROV-22-K50
14
Y-Piece Assembly
PROV-32-K
5
Belt and buckle
PROV-23-K
15
Connector
PROV-33-K
6
1.2m Hose (To Spray Gun)
PROV-406-K
16
Filter Cap Seal
PROV-34-K4
7
Rigid acetate visor face seal and air tube
PROV-25-K
Hoses
8
Storage bag
PROV-26-K
10m Air hose - 5/16”ID male & female QD’s
H-6085-QD
9
Filter element (Pack 4)
PROV-27-K4
10m Air hose - 5/16”ID
H-6065-B
Catalogue 2015
37
Complete Air-Fed Half-Mask Outfit
A single airline supplies breathing and spraying air.
One piece high specification goggles are included.
The facepiece incorporates dual exhalation valves and an air
inlet diffuser.
Waistbelt incorporates odour filter and pre-set mask air
regulator.
Outfit includes high quality gun hose (1.2m x 8mm bore).
Specification
Protection
APF=20
Carbon Filter Life
1000 hours
Supply Pressure
3.8 bar (55 psi)
- At hose supply connection max 7 bar (100 psi)
MPV-627 Outfit
Part No
Description
MPV-627
Complete air-fed half-mask outfit
Accessories
38
Part No
Description
MPV-506-2
Complete half-mask with cotton rimlet, hood & air tube
MPV-4006
One piece protective goggles for use with half mask
MPV-486
Half mask rubber facepiece only
MPV-489-K2
Half-mask exhalation valve
MPV-17-K10
Cotton mask-to-face rimlet-kit of 10
MPV-487
Rubber strap harness for half mask
MPV-488
Half-mask clear air tube assembly with mini QD fitting
H-6085-QD
10 metre length air hose complete with male and female QD’s
H-6065-B
10 metre length air hose complete with re-usable fittings
MPV-518
Complete waistbelt with regulator, filter cartridges & QD’s
MPV-22
Replaceable waistbelt filter cartridge
MPV-455
Waistbelt regulator (does not include belt or QD)
MPV- 519
Waistbelt filter housing
MPV-2-K5
Disposable elasticated protective hood – kit of 5
MPV-456
Rubber spray gun hose (4’ long, 5/16” bore with QD fittings)
MPV-458
Stowage bag for masks or visors
MPV-424
Female, self-sealing, QD air line fitting
MPV-10
Male stem, QD air line fitting with 1/4” BSP (M)
MPV-5
Male stem, QD air line fitting with 1/4” BSP (F)
MPV-462
Female self sealing QD fitting with 1/4” BSP (F)
MPV-463
Kit of 4 QD’s fittings (2 male and 2 female)
MPV-442
Female miniature QD fittings for waistbelt to mask / visor
MPV-20
Male miniature QD stem for waistbelt to mask / visor
MPV-4006
MPV-22
MPV-463
MPV-60-K3
H-6085-QD
Catalogue 2015
Ref
No
Description
Part No.
Ref
No
Description
Part No.
1
Mask Assembly (ref nos 2-8)
MPV-506-2
13
Quick detachable stem
MPV-10
2
Facepiece
MPV-486
14
Quick detachable connector
MPV-424
15
3
Exhalation Valve (kit of 2)
MPV-489-K2
4
Kit of 10 cotton rimlets
MPV-17-K10
10m length M-F QD Fittings #
H-6085-QD
10m length 1/4” Re-usable Fittings #
H-6065-B
5
Harness
MPV-487
16
Gun hose assembly
MPV-456
6
Hoods (kit of 5)
MPV-2-K5
17
Quick detachable stem
MPV-5
7
Tube and mask diffuser assembly
MPV-488
18
Stowage bag
MPV-458
8
Quick detachable stem
MPV-20
19
Goggle
MPV-4006
9
Quick detachable connector
MPV-442
19a
Goggle protection strip (kit of 10)
MPV-59-K10
10
Regulator and housing
MPV-455
20
Waistbelt assembly
MPV-518
# Not part of outfit, order separately
11
Disposable filter
MPV-22
12
Waistbelt & filter housing
MPV-519
Catalogue 2015
39
“Valuair” Half-Mask Respirator
Lightweight, soft, pliable facepiece.
Easy bayonet fitting filter cartridges.
Lightweight, dual filter, semi-disposable half mask
respirator.
Comfortable elasticated / moulded headstrap
Can be used up to a maximum of 28 days.
Replaceable A2 specification cartridges supplied
Low nose bridge helps to accommodate goggles
Pre filters to extend the service life of the main
Headstrap has no buckles or fasteners and is
cradle.
as standard.
filter cartridges.
40
“Freedom” Half-Mask Respirator
Maintenance free and requires no spare parts.
for optimum vision.
comfortable and easy to use.
Specification – A2 Filters
Specification – A2 Filters
A2 filters are for use against organic vapours with boiling points
above 650°C.
A2 filters are for use against organic vapours with boiling points
above 650°C.
The Valuair mask with A2 filter cartridges can therefore be used
in areas of contamination up to 10 x the Occupational Exposure
levels set by the Health and Safety Executive.
The Freedom mask with A2 filter cartridges can therefore be
used in areas of contamination up to 10 x the Occupational
Exposure levels set by the Health and Safety Executive.
Suitable for use with cellulose paints, primers, lacquers and
varnishes but not suitable for use with Isocyanates.
Suitable for use with cellulose paints, primers, lacquers and
varnishes but not suitable for use with Isocyanates.
Assigned Protection Factor of 10.
Assigned Protection Factor of 10.
Part No
Description
Part No
Description
MPV-629
Valuair Cartridge Mask complete with A2
Filter cartridges and pre-filters
MPV-496
Freedom Cartridge Mask complete with A2
Filter cartridges
MPV-492
Pair of pre-filter covers plus ten filter pads
MPV-4006
MPV-494-K2
Pack of two A2 specification filter cartridges
One piece protective goggles for use with
half masks
MPV-4006
One piece protective goggles for use with
half masks
Catalogue 2015
AVA
SPR ILABL
ING
E
201
5
Pro AIR-1 Filter Regulator
Rolling diaphragm gives rapid response and sensitive air
pressure control.
Provides air filtered to 5 microns.
Maximum airflow 3500 l/min (124 cfm).
Three ball valve controlled outlets.
Tamperproof, removable and lockable air pressure control knobs.
Specification
Air Inlet Thread
1/2” BSP (F)
Regulated Outlets
3 Valved
Unregulated Outlets
N/A
Air Outlets (Ball Valves)
1/ 4” BSP (M)
Width (Overall)
175mm (6.9”)
Height (Overall)
280mm (11”)
Weight
2500 gms (88oz)
Capacity (maximum air flow)
3500 l/min (124cfm)
Maximum Air Inlet Pressure
13 bar (189 psi)
Maximum Regulated Outlet Pressure
0-8 bar (0-116psi)
Pressure Gauge
0-11 bar (0-160 psi)
Gauge port
1/8” BSP (F)
Air Filtration
Down to 5 microns
Drain Valve
Semi-Automatic
Maximum Pressure Drop
5% of Inlet Pressure
Maximum Operating Temperature
80°C (176°F)
Pro Air-1 Regulator
Part No
Description
PROAIR-1
3 Outlet Filter Regulator (90 cfm)
DV-9420601
Filter bowl removal tool
Ref No
Description
Part Number
1
Upper Cover Assembly
PROAIR-71
2
Filter (Air)
PROAIR-51
3
Metal Filter Bowl
PROAIR-72
4
Ball Valve
SER-3414-MF
5
Pressure Gauge
GA-319
(See Page 58 & 59 for current DVFR Range)
Catalogue 2015
41
AVA
SPR ILABL
ING
E
201
5
pro air-2 Filter Regulator COALESCER
High air flows for conventional and compliant spray guns.
Provides air filtered to 0.01 microns suitable for air-fed
respiratory outfits.
Maximum airflow of 3500 l/min (124cfm).
Three ball valve controlled outlets.
Rolling diaphragm gives rapid response and sensitive air pressure control.
Specification
Air Inlet Thread
1/2” BSP (F)
Regulated Outlets
3 Valved
Unregulated Outlets
N/A
Air Outlets (Ball Valves)
1/ 4” BSP (M)
Width (Overall)
240mm (9.5”)
Height (Overall)
280mm (11”)
Weight
3200 gms (113oz)
Capacity (maximum air flow)
3500 l/min (124cfm)
Maximum Air Inlet Pressure
13 bar (189 psi)
Maximum Regulated Outlet Pressure
0-8 bar (0-116psi)
Pressure Gauge
0-11 bar (0-160 psi)
Gauge port
1/8” BSP (F)
Air Filtration
Down to 0.01 microns *
Drain Valve
Semi-Automatic
Maximum Pressure Drop
10% of Inlet Pressure
Maximum Operating Temperature
80°C (176°F)
* Suitable for Breathing Air
Pro Air-2 Regulator
Part No
Description
PROAIR-2
3 Outlet Filter Regulator Coalescer (50 cfm)
DV-9420601
Filter bowl removal tool
Ref No
Description
Part Number
1
Upper Cover Assembly
PROAIR-71
2
Filter (Air)
PROAIR-51
2a
Filter Element Only
-
3
Metal Filter Bowl
PROAIR-72
4
Ball Valve
SER-3414-MF
5
Pressure Gauge
GA-319
6
Fine Filter (Oil)
PROAIR-52
7
Isolation Valve
DV-8000035
8
Filter Kit (Includes Items 2, 6)
PROAIR-62
(See Page 58 & 59 for current DVFR Range)
42
Catalogue 2015
AVA
SPR ILABL
ING
E
201
5
pro air-3 Filter Regulator
Coalescer with Activated Carbon Filter
High air flows for conventional and compliant
spray guns.
Provides air filtered to 0.01 microns suitable for
air-fed respiratory outfits.
Activated carbon filter removes oil carry over to 0.003 microns.
Maximum airflow of 3500 l/min (124cfm).
Three ball valve controlled outlets.
Rolling diaphragm gives rapid response and sensitive air
pressure control.
Specification
Air Inlet Thread
1/2” BSP (F)
Regulated Outlets
3 Valved
Unregulated Outlets
N/A
Air Outlets (Ball Valves)
1/ 4” BSP (M)
Width (Overall)
305mm (12”)
Height (Overall)
280mm (11”)
Weight
3.3kg
Capacity (maximum air flow)
3500 l/min (124cfm)
Maximum Air Inlet Pressure
13 bar (189 psi)
Maximum Regulated Outlet Pressure
0-8 bar (0-116psi)
Pressure Gauge
0-11 bar (0-160 psi)
Gauge port
1/8” BSP (F)
Air Filtration
Down to 0.01 microns *
Drain Valve
Semi-Automatic
Maximum Pressure Drop
10% of Inlet Pressure
Maximum Operating Temperature
80°C (176°F)
* Suitable for Breathing Air
Pro Air-3 Regulator
Part No
Description
PROAIR-3
3 Outlet Filter Regulator Coalescer with activated carbon filter
DV-9420601
Filter bowl removal tool
Ref No
Description
Part Number
1
Upper Cover Assembly
PROAIR-71
2
Filter (Air)
PROAIR-51
2a
Filter Element Only
-
3
Metal Filter Bowl
PROAIR-72
4
Ball Valve
SER-3414-MF
5
Pressure Gauge
GA-319
6
Fine Filter (Oil)
PROAIR-52
7
Isolation Valve
DV-8000035
8
Activated Carbon Filter
PROAIR-53
9
Filter Kit (Includes Items 2, 6, 8)
PROAIR-63
Catalogue 2015
(See Page 58 & 59 for current DVFR Range)
43
Economy Filter Regulators and Coalescers
Please Note: Economy
FLFR-1 Filter Regulator
Air filtration down to 20 microns.
Regulators are not suitable
High quality manufacture.
for low bake temperatures.
Air flow of 70cfm (at 7 bar – 100psi inlet pressure).
Lockable and removable (tamperproof) control.
FLCF-1 Coalescing Filter
FLFR-1
A 3/8” (port size) coalescing (fine oil) filter.
Air filtration down to 0.01 microns.
Replaceable filter element.
Maximum working pressure 18 bar (260 psi).
FLCF-1
FLRC-1 – Filter Regulator Coalescer
Compact, low cost single operator Filter Regulator and Coalescer.
Filtration down to 0.01 microns suitable for air mask or visor.
FLRCAC-1
FLRCAC-1
FLRC-1
FLRCAC-1 Filter Regulator Coalescer with Activated
Carbon Filter
High efficiency filter designed to remove dirt, liquid oil
and water from spraying and breathing air.
Filtration down to 0.01 microns plus activated carbon
filter removing contaminants down to 0.003 microns.
Regulator Assemblies
44
Part No.
Description
Part No.
Description
FLFR-1
Single outlet Filter Regulator (70cfm)
XA-12
Replacement coalescing filter element (FLRC + FLRCAC)
FLCF-1
Coalescing (fine oil) filter (25cfm)
AC-12
Replacement activated carbon filter (FLRCAC)
FLRC-1
Single outlet Filter Regulator Coalescer
9450802
Upper Cover (All)
FLRCAC-1
Single outlet filter regulator coalescer with activated
carbon filter
9450301
Metal Bowl (All)
GA-319
Gauge (FLFR+ FLRC+ FLRCAC)
9450102
Replacement filter element (FLFR, FLRC, FLRCAC)
Catalogue 2015
i-SYSTEM PRO AIR CAP, FLUID TIP AND NEEDLE KITS
Gun Model
GTi Pro Lite
GTI Pro Gravity
GTI Pro Suction
Kit Part No
PROL-455-HV30-12
PROL-455-TE10-12
PROL-455-TE20-12
PROL-455-HV30-13
PROL-455-TE10-13
PROL-455-TE20-13
PROL-455-HV30-14
PROL-455-TE10-14
PROL-455-TE20-14
PRO-450-H1-12
PRO-450-T1-12
PRO-450-T2-12
PRO-450-H1-13
PRO-450-T1-13
PRO-450-T2-13
PRO-450-H1-14
PRO-450-T1-14
PRO-450-T2-14
PRO-451-H1-16
PRO-451-T1-16
PRO-451-T2-16
PRO-451-H1-18
PRO-451-T1-18
PRO-451-T2-18
PRO-451-H1-20
PRO-451-T1-20
PRO-451-T2-20
PRO-451-T4-085
PRO-451-T4-10
PRO-451-T4-12
PRIPRO-450-P1-14
PRIPRO-450-P1-16
PRIPRO-450-P1-18
PRIPRO-450-P1-20
PRIPRO-450-P1-25
SRIPRO-450-TS1-08
SRIPRO-450-HS1-08
SRIPRO-450-TS1-10
SRIPRO-450-HS1-10
SRIPRO-450-TS1-12
SRIPRO-450-HS1-12
GTI Pro Pressure
PRO-451-T4-14
PRi Pro Gravity
SRi Pro
Catalogue 2015
45
Gravity and Suction Cup Accessories
Gravity Feed Cups
46
Part No
Description
GFC-501
568ml (1 Pint) Acetal gravity cup for GTI / GFG
KGP-509-1
284ml (1/2 Pint) Nylon gravity cup for GFG
SRi-510
125ml Acetal gravity cup
SRi-42-K3
Pack of 3 cone filters
Part No
Description
SRi-478-K12
Pack of 12, 125ml gravity cups for SRi
KR-566-1-B
GFC-402
Lid assembly for GFC-501 gravity cup
1 litre standard suction cup and lid assembly for
JGA
KGP-401
Lid assembly for KGP-509 gravity cup
KR-466-K
Cup only – 1 litre suction cup
GFC-17-K5
Washer
KR-4001-B
Suction cup lid assembly for JGA cups
GFC-2-K5
Pack of 5 drip check lids
KR-115-K5
Pack of 5 drip free diaphragms
KGP-5-K5
Pack of 5 gravity cup strainers for GFC-501 &
KGP-509
KR-11-K3
Pack of 3 Tri-Seal gaskets for KR suction cups
KR-69-K3
Pack of 3 Leather gaskets for suction cups
KR-483-K10
Kit of 10 mesh KR cup strainers – to fit 7/16” tube,
115 Micron
KR-484-K10
Kit of 10 mesh KR cup strainers – to fit 7/16” tube,
350 Micron
KR-110-K3
Kit of 3 Spot Pots
SRi-8-K6
Pack of 6 lids for SRi gravity cups
KR-459-K5
Mini cups
GFC-502
Gravity Cup Aluminium 1l
GFC-404-K2
Disposable Lid Kit (GFC-502)
Suction Feed Cups
Catalogue 2015
In-Line Air Filters
Lightweight, gun mounting air filter
High efficiency action traps water, oil and dirt
Tough solvent resistant acetal housing with 1/4” threads
Part No: HAF-507-K12
In-Line Air Adjusting Valve
Fits neatly in-line at the gun air inlet
Increase or decrease working pressure at the gun
Calibrated up to 11 Bar (160 psi)
Part No: HAV-501-B
Gun Cleaning Brushes
Ideal for a variety of gun cleaning jobs
Tough resilient bristles for useful service
Suitable size for cleaning most parts of the gun
Part No: 4900-5-1-K3 Pack of 3 brushes
Duster/Blow Guns
Palm size trigger operated with diffused air flow
Low noise factor
Durable design
Part No: DGD-505-E
Viscosity Cups
The fast, simple way to check out paint viscosity
Tough durable and easy to clean
Precision metal drain out insert
Part No: 7000-114-K2 Pack of 2 viscosity cups
Mixing Cups
Easy to use, disposable mixing cups
Made from solvent resistant clear polypropylene
Calibrated with a 0-600 volumetric measurement scale
Part No: MC-1-K50 Pack of 50 cups
Part No: MC-2-K50 Pack of 50 lids
Part No: MC-1-K1000 Pack of 1000 cups Part No: MC-2-K1000 Pack of 1000 lids
Trigger Clip
Made from solvent resistant acetal
Locks trigger in open position for gun wash machine
Snaps in place for secure fit
Part No: PRO-15-K3
Professional Spray Gun Cleaning Kit
Handy tool wrap style kit of purpose made cleaning brushes and tools
Includes cleaning instructions and spray gun oil
Keeps your spray guns in top working order
Part No: KK-4584
Spray Gun Service Kit
Spray gun service/repair kit for GTIPRO and SRIPRO
Part Nos: PRO-415-1 – Service kit
Catalogue 2015
47
DGi PRO Digital Gauge
The most accurate digital gauge available
Clear and easy to read, just squeeze the trigger to set
Smooth, accurate control even when wearing gloves
Part No: DGIPRO-502-BAR
DGi PRO pod
Perfectly positioned for easy checking
Accurate digital “bar” read-out of working pressure
Accurate readings to within 0.05 bar (0.7 psi)
Part No: DGIPRO-503-BAR-K (GTi Pro)
Part No: DGIPRO-504-BAR-K (GTi Pro LITE)
Gravity Gun Stands
Stable metal workbench gun stands
Choice of 2 stands for 3 gravity guns or a single gun
Single gun stand is ideal for SRi guns and full size guns
Part Nos: GGS-1 – 3 gun stand
GFV-50-F – single gun stand
Gravity Cup Filters
Effectively removes dirt, flakes and scum
Keeps the finish blemish free
Resistant to most solvents – easily cleaned
Part No: KGP-5-K5 - Pack of five filters
Suction Cup Filters
Convenient, easy fit suction cup paint filters
Keeps spray gun passages clear
Removes dirt, flakes and scum
Part Nos: KR-484-K10 51 mesh filter screen (general purpose)
KR-483-K10 130 mesh filter screen (finer filtration)
Suction Cup Lid Gaskets
Ready to use, purpose fit suction cup lid seals
Choose between Tri-Seal or traditional leather gaskets
Fits all DeVilbiss KR type suction cups
Part Nos: KR-11-K3 Tri-seal gaskets
KR-69-K3 Leather gaskets
Drip-Free Diaphragms
Prevents suction cup leaks and vent hole blockages
Allows the cup to be used at angles
Fits snugly under the cup lid
Part No: KR-115-K5 (Pack of 5)
Spot Pots
0.5 litre capacity nylon cup insert cuts down on costly paint mixes
Tapered base ensures that minimal quantities of paint can be utilised
Quickly and easily cleaned for frequent colour changes
Fits all 1 litre capacity KR type suction cups
Part No: KR-110-K3
Gun Lube
Pack of 10 gun lube sachets.
Part No: GL-1-K10
48
Catalogue 2015
Hose & Fittings
High Flow Air Hose with Connections.
High air flow, high quality rubber air hose.
8mm (5/16”) bore ideal for use with conventional, compliant / HVLP spray guns, air fed breathing equipment
and other air tools.
Option 1
Option 2
10 metre length air hose complete with
10 metre length air hose complete with
quality chrome replaceable 1/4” swivel nut
crimped female quick detach connection at
female fittings either end.
one end and crimped male QD fitting at the
Part No: H-6065-B
other end.
Part No: H-6085-QD
Option 3
10 metre length air hose complete with
crimped female quick detach connection at
one end and crimped female loose nut fitting
at the other end.
Part No: H-6086-B
High Flow Air Hose Assemblies
Red rubber air hose assemblies including 1/4” BSP connections
Part No
Description
Part No
Description
H-7501HA-1.2
1.2 metre, 5/16”ID Air Hose Assembly
– For KBII
H-7501HA-10
10 metre - 5/16”ID Air Hose Assembly
H-7501HA-5
5 metre, 5/16”ID Air Hose Assembly
H-7501HA-15
15 metre - 5/16”ID Air Hose Assembly
H-7501HA-7.5
7.5 metre - 5/16”ID Air Hose Assembly
H-7502HA-7.5
7.5 metre - 3/8”ID Air Hose Assembly
H-7502HA-10
10 metre - 3/8”ID Air Hose Assembly
H-7502HA-15
15 metre - 3/8” ID Air Hose Assembly
Air Hose Connections
Part No: PA-HC-4527
Part No: PA-HC-4528
1/4” BSP Female (8mm (5/16”) hose bore)
1/4” BSP Female (9.5mm (3/8”) hose bore)
Fluid Hose Assemblies
Black rubber fluid hose assemblies including 3/8” BSP connections
Part No
Description
Part No
Description
H-7503HA-1.45
1.45 metre 1/4” ID Fluid Hose
Assembly – For KBII
H-7503HA-10
10 metre 1/4” ID Fluid Hose Assembly
H-7503HA-5
5 metre 1/4” ID Fluid Hose Assembly
H-7503HA-15
15 metre 1/4” ID Fluid Hose Assembly
H-7503HA-7.5
7.5 metre 1/4” ID Fluid Hose Assembly
H-7504HA-10
10 metre 3/8” ID Fluid Hose Assembly
H-7504HA-15
15 metre 3/8” ID Fluid Hose Assembly
Fluid Hose Connections
Part No: PA-HC-4543
Part No: PA-HC-4548
3/8” BSP Female (6mm (1/4”) hose bore)
3/8” BSP Female (9.5mm (3/8”) hose bore)
Quick detach fittings
High flow connections – minimal pressure drops
Ideal for spray guns, respirators, hoses and regulators
MPV-5 – Male quick detach stem with 1/4” female fitting: MPV-424 – Female quick detach connection with 1/4” male fitting: MPV-10 – Male quick detach stem with 1/4” male fitting: MPV-462 – Female quick detach with 1/4” female fitting: MPV-463 – Economy pack, includes 1 of each shown in the picture to the right: MPV-60-K3 – Male quick detach Uni Swivel stem with 1/4” female fitting: Catalogue 2015
49
KBII 2.3 LITRE REMOTE CUP
2.3 litre capacity – greater area
coverage, less refills.
Aluminium or stainless steel options (for
waterbase materials).
Familiar gun grip handle plus belt hook
for operator convenience.
At-the-job controls with lid mounted pressure
gauge.
Available complete with short cup to gun air and
fluid hoses
KB disposable liners make cleaning and colour
changes fast and simple.
Specification
Air Inlet and outlet connections threads
1/4” BSP (M)
Fluid outlet connection (to spray gun)
3/8” BSP (M)
Maximum working pressure
2.1 Bar (30 psi)
Maximum air supply pressure
8.6 bar (125 psi)
Height
183 mm
Weight (less hoses)
1.76 kg
Cup Capacity
2.3 litres
Spray Gun Kits for use with KBII
Part No
Description
GTIPPRO-**-***
Pressure Feed Gun with either H1, T1, T2, T3 or T4 air cap and either 085, 10, 12, 14, 16, 18
or 20 fluid tip
PROPL -**-***
GTi Pro LITE Pressure Feed Gun with either TE10, TE20, TE30 or TE40 air cap and either 085,
10, 12 or 14 fluid tip
JGAPPRO-**-***
Pressure Feed Gun with either C1, C2 or C3 air cap and either 085 12, 14, 16 or 18 fluid tip
Kit contents are spray gun, (suction cup with filter if appropriate), Torx key, brush and multi-fit spanner
** = Air Cap / *** = Fluid Tip
KBII Remote Cup kits
Part No
Description
KB-522
Aluminium Remote Cup without hoses
KB-522-SS
Stainless Steel Remote Cup without hoses
KB-622
Aluminium Remote Cup complete with air and fluid hoses
KK-5051
Accessories
50
Part No
Description
KB-422
Aluminium 2.3 Litre KBII Spare Cup Only for KB-522
KB-442
Stainless Steel 2.3 Litre KBII Spare Cup Only for KB-522-SS
KK-5051
Kit of 20 disposable liners plus lid diaphragms
H-7501HA-1.2
1.2m Air Hose Assembly with BSP Fittings
H-7503HA-1.45
1.45m Fluid Hose Assembly with BSP Fittings
GA-355
Air Pressure Gauge for KBII - 0-30psi
KB-422
Catalogue 2015
Ref
No
Description
Part Number
Ref
No
Description
Part Number
1
Retaining Ring
KB-64
15
Regulator Assembly
KB-428-1
2
Slip Rings
KB-81-K5
16
Spring
-
3
Handle
KB-74
17
Valve
-
4
CD Nut
-
18
Valve Seat and Seal
-
5
Connector 1/4” BSP
JGA-158
19
Diaphragm
-
6
Pressure Relief Valve
KB-66
20
Slip Ring
-
7
Lid
Not available
21
Spring
-
8
Gauge
GA-355
22
Bonnet
-
9
Seal
KB-80-K5
23
Seal kit of 6
KB-60-K6
10
Locknut (KB-522) kit of 5
MBD-11-K5
24
Tube Assembly 3/8” BSP (KB-522-B)
KK-4997
11
Cup – Aluminium (KB-522)
KB-422
Tube Assembly 3/8” BSP STS (KB-522-SS)
KK-4996
Cup – Stainless Steel (KB-522-SS)
KB-442
25
Check Valve and Seal Assembly
KB-444
12
Check Valve kit of 3
KB-432-K3
26
Seal kit of 5
KB-101-K5
13
Seal kit of 5
KB-85-K5
Hose & Fittings
14
Safety Valve
TIA-4355
Catalogue 2015
1.2m Air Hose Assembly with BSP Fittings
H-7501HA-1.2
1.45m Fluid Hose Assembly with BSP Fittings
H-7503HA-1.45
51
BINKS DX SERIES: AIR OPERATED 1:1 RATIO DIAPHRAGM PUMPS
Acetal pump body with stainless steel balls and soft seats for universal paint compatibility.
The unique diaphragm design and “built in” fluid regulator provide consistent
pressure and readily adjustable paint flow.
The Non-stall air valve provides smooth, quiet and surge free paint delivery up
to 1000 cc/minute.
Clearly labelled Air regulators provide independent control of pump and
spray gun fluid and air pressures.
Quick release air, fluid inlet and outlet connections for faster maintenance.
Re-circulation/dump valve accessory for faster colour changes reducing down
time, saving time and money.
Pump outfit mountings include Cart, Wall and Tripod outfits with or without
spray guns & hoses.
Specification
Pump Ratio
1 to 1
Max. Air Pressure
7 Bar / 100 PSI
Max. Fluid Pressure
7 Bar / 100 PSI
Nominal Flow Volume / Cycle
0.07 Litres (0.018 US Gall)
Fluid Output @ 60 cycles/min
4.2 Litres / min (1.1 US Gall / min)
Max Recommended Continuous Cycle Rate
10 Cycles /min
Max Recommended Intermittent Cycle Rate
30 Cycles /min
Inlet Fluid Connection
3/8” Universal (BSPP/NPSM) Male or Female
Outlet Fluid Connection
3/8” Universal (BSPP/NPSM) Male or Female
Maximum Dry/Wet Lift
6.6m (21.8 feet)
Air Inlet
G1/4” (BSPP) Female
Fluid Regulator Pilot
Ø4 Tube
Air Volume / cycle @ 6.9Bar/100psi
0.77L (0.027SCFM)
Air Flow @ 10 cycles/min 6.9 bar/100psi
7.7L/min (0.27SCFM/min)
Air Flow @ 30 cycles/min 6.9 bar/100psi
23.2L/min (0.82SCFM/min)
Air Quality ISO 8573.1 Class 3.3.2 #
Dirt 5 microns
Water -20°C @ 7bar (940ppm)
Oil 0.1mg/m3
Non Lubricated
Noise Level
68db LAeq
Earth (Air Inlet Cover)
<1Ω
Weight – Bare Pump
2.2 Kg (4.9 lbs)
Spray Gun Kits for use with the DX Pump:
Part No
Description
PROPL -**-***
PROPL -**-*** GTi Pro LITE Pressure Feed Gun with either TE10, TE20, TE30
or TE40 air cap and either 085, 10, 12 or 14 fluid tip
DX Pump Outfits:
52
Part No
Description
DX70R3-CF2
Cart mounted pump outfit with filter and three air controls
DX70R3-TF2
Tripod mounted pump outfit with paint filter and three air controls
DX70R3-WF2
Wall mounted pump with paint filter and three air controls
Catalogue 2015
Ref. Description
No
1
Check valve seal kit x4
Part No.
2
Check valve kit x4
DXK-2
3
Diaphragm kit x2
DXK-3
4
Shaft & seal kit
DXK-4
5
End cap seal kit x2
DXK-5
6
Caps & screws x2
DXK-6
7
End cap nut x10
DXK-7
8
End Cap
DXK-8
DXK-1
Ref. Description
Part No.
No
9
Inlet, outlet & plug connector seal kit DXK-9
10
Male inlet connector kit
DXK-10
11
Female inlet connector kit
DXK-11
12
Male outlet connector kit
DXK-12
13
Female outlet connector kit
DXK-13
14
Air valve kit
DXK-14
15
Fluid regulator kit
DXK-15
16
Regulator cap & screws
DXK-16
17
Inlet (x2) & outlet (x2) clips
DXK-17
18
Cover, seal & screws
DXK-18
19
Female inlet / outlet thread seal x4
DXK-19
20
O-ring x5
DXK-20
21
O-ring x5
DXK-21
22
O-ring x5
DXK-22
23
O-ring x5
DXK-23
24
O-ring x5
DXK-24
25
Gasket x4
DXK-25
26
Blanking plate & screws ‡
DXK-26
27
Blanking gasket x 4 ‡
DXK-27
28
Insert ‡
DXK-28
29
Grounding cable 4m
0114-011798
‡ = parts for non-fluid regulator model
Catalogue 2015
53
32:1 HIGH PRESSURE PUMP WITH BINKS AA4400M AIR ASSISTED AIRLESS
Patented air valve technology. Enables pump to change over quickly
to significantly reduce pulsation.
Long lasting ceramic coated piston rods. Superior wear resistance
lasting up to three times longer than hard chrome pistons.
Designed to pump long with less downtime and extended packing
life. Self-adjusting sprint loaded fixed packings last up to three times
longer than the competition. Large sight glass for visual packing
inspection.
Air Assisted Airless HVLP & A75 guns provide the latest atomisation
technology.
Stainless Steel system – pump and gun.
Unique Trans-Tech or HVLP air caps provide a ‘softer fine spray’ for
superior finish quality and higher transfer efficiency than competitors.
Lightweight and Operator friendly design with lighter trigger pull
tension.
Easy to remove ‘in-line’ needle assembly for quick maintenance.
Adjustable needle packing and ‘balanced’ air valve design.
Gun handles Solvent and Waterborne coatings as standard.
Standard flat tips, fine finish tip and twist tip cleaner available with a
wide range of tips from 0.18mm to 0.89mm.
Part No.
Description
MXL432PU-C-F-ACG
Cart Mounted (Part No includes A4400M Gun)
MXL432PU-C-T-ACG
Tripod Mounted (Part No includes A4400M Gun)
Pump Specification
Gun Specification
Ratio
32:1
8.0 bar (116 psi)
Air/Fluid inlet thread
¼” Universal (M)
Max Inlet Pressure
Fluid passageways
Stainless Steel
Flow Rate Nominal
1.4 l/min
Gun Weight
490g
Flow Rate Max
4.0 l/min
Gun Body
Forged Aluminium
Volume/Cycle
24cm3
Max working fluid pressure
303 bar (4400 psi)
Max Operating Pressure
256 bar (3600 psi)
Max air inlet pressure
6.9 bar (100 psi)
Cylinder Diameter
85 mm
Seat
Tungsten Carbide
Piston Stroke
75 mm
Stainless steel inline paint filter
100 mesh
Air Consumption @ 20 cycles/min
147 l/min
Accessories
54
Part No
Description
0110-009132
Filter insert for high pressure filter - 100 mesh
0110-009133
Filter insert for high pressure filter - 150 mesh
0110-009134
Filter insert for high pressure filter - 200 mesh
54-5788-K5
AAA 4400 spray gun filter kit of 5 - 60 mesh
54-5789-K5
AAA 4400 spray gun filter kit of 5 - 100 mesh
FOR A DETAILED BREAKDOWN OF THE
MXL PUMPS PLEASE CONSULT YOUR
SERVICE BULLETIN OR CONTACT THE
DEVILBISS CUSTOMER SERVICE DEPARTMENT.
Catalogue 2015
Ref
No
Description
Part Number
Ref
No
Description
Part Number
1
Gun Body
-
12
Baffle Plate (Kit of 10)
SPA-71-K10
Fluid Filter 60 Mesh (Kit of 5)
(100 Mesh Filter (Kit of 5) 54-5789-K5)
54-5788-K5
2
3
Fluid Seat (4400 psi) (Tungsten Carbide)
54-5799-K
13
Fluid Inlet Swivel (1/4” NPS)
-
3A
Twist Tip Fluid Seat (4400 psi) (Tungsten
Carbide)
54-5832-K
14
Filter Adapter Nut
-
15
Air Inlet Fitting 1/4” NPS (Kit of 3)
SN-9-K3
4
Gasket (Kit of 10)
SPA-98-K10
16
Filter Bracket Screw
-
5
Flat Tip (Fine Finish Tips 9-XXXX-F)
114-XXXXX
17
Filter Bracket
-
5A
Twist Tip
9-XXX-75
18
Fluid Needle Assembly (4400 psi)
-
5B
Twist Tip Brace (Kit of 2)
54-7539-K2
19
Blanking Needle Nut
54-5850
6
Flat Tip HVLP Air Cap
(Flat Tip Trans-Tech Air Cap 54-5797-K)
54-5890-K
20
Needle Spring Pad
-
6A
Twist Tip HVLP Air Cap
(Flat Tip Trans-Tech Air Cap 54-5798-K)
54-5924-K
21
Needle Spring (4400 psi)
-
22
Spreader Valve Assembly
54-5815
7
Retaining Ring
54-5852
23
Body Bushing
-
8
Flat Tip Guard
54-5794
24
Body Bushing Gasket
-
8A
Twist Tip Guard
54-5921
25
Trigger Nut
-
9
Air Valve Assembly
SN-402-K
26
Trigger Screw
-
10
Trigger
-
27
Top Filter Seal
-
11
Fluid Tube Assembly
54-5780
28
Bottom Filter Seal
-
Catalogue 2015
55
Binks Pressure Feed Tank
Zinc plated tank shell for long service life.
Single regulator and gauge to control tank and air pressure.
Zinc plated lid assemblies for solvent based coatings.
Positive four point lid clamping for secure operation.
High density polyethylene, tank liners ensure efficient use.
Specification
Tank Capacity
9.5 litre
Maximum working Pressure
5.5 bar (80psi)
Safety Valve Set Pressure
5.5 bar (80psi)
Air Inlet Size
1/4” BSP (M)
Fluid Outlet Size
3/8” BSP (M)
Tank Shell
SA-620 H.R Steel Zinc plate 2.7mm (8 gauge)
Tank Lid
SA-414 H.R Steel Zinc plate 4.2mm (3/16”)
Fluid Tube
Steel, Galvanised Zinc Plate
Air Manifold
CRS Zinc Plated
Fluid Outlet
Steel, Galvanised Zinc Plate
Lid Gasket
Santoprene ™
Spray Gun Kits for use with KBII
Part No
Description
GTIPPRO-**-***
Pressure Feed Gun with either H1, T1, T2, T3 or T4 air cap and either 085, 10, 12,
14, 16, 18 or 20 fluid tip
PROPL -**-***
GTi Pro LITE Pressure Feed Gun with either TE10, TE20, TE30 or TE40 air cap
and either 085, 10, 12 or 14 fluid tip
JGAPPRO-**-***
Pressure Feed Gun with either C1, C2 or C3 air cap and 085 12, 14, 16 or 18 fluid
tip
Kit contents are spray gun, (suction cup with filter if appropriate), Torx key, brush and multi-fit spanner
** = Air Cap / *** = Fluid Tip
Pressure Feed Tank
56
Part No
Description
83C-210-B
9.5 litre capacity zinc plated tank and lid assembly
PT-78-K10
Kit of 10 polyethylene inner liners for 9.5 litre capacity tank
VS-521
Paint filter (100 mesh) and housing – fits directly onto fluid outlet of tank NPSM
VS-522
Paint filter (100 mesh) and housing – fits directly onto fluid outlet of tank - BSP
H-7501
PA-HC-4527
8mm (5/16”) bore red rubber air hose
1/4” BSP Female (8mm (5/16”) hose bore)
H-7502
PA-HC-4528
9.5mm (3/8”) bore red rubber air hose
1/4” BSP Female (9.5mm (3/8”) hose bore)
H-7503
PA-HC-4543
6mm (1/4”) bore black rubber fluid hose
3/8” BSP Female (6mm (1/4”) hose bore)
H-7504
PA-HC-4548
9.5mm (3/8”) bore black rubber fluid hose
3/8” BSP Female (9.5mm (3/8”) hose bore)
PT-78-K10
Hose by the metre
H-7501 &
PA-HC-4527
Hose by the metre
H-7503 &
PA-HC-4543
Catalogue 2015
Ref
No
Description
Part Number
Ref
No
Description
Part Number
1
Tank Assembly Kit (Includes Ref Nos. 1A, 13,
14, 15 & 16)
-
13
Thumb Screw
-
1A
Tank Shell
-
14
Yoke Assembly
-
2
Lid Gasket, Santoprene
PT-33-1
15
Cotter Pin, 3/32 x 1”
-
3
Lid, Zinc Plated
-
16
Hinge Pin
-
4
Gauge
83-2727
17
Fluid Tube
PT-31
5
Regulator
HAR-511
18
Tank Liner (Kit of 10)
PT-78-K10
6
90° Swivel Adaptor 1/4’ NPS (F) x 1/4’ NPT (M)
SSP-30-ZN
Tank Liner (Kit of 60)
PT-78-K60
7
Cross 1/4’ NPT (F)
-
19
Hex Nipple 1/4’ NPT (M)
SSP-462-ZN
8
Safety Valve - 80 psi
TIA-5080-CE
20
Air Relief Valve
SS-2707
9
Handle
PT-32
21
D.M Nipple
83-4233
10
Hex Nut 3/8’ – 16
-
22
(NPS) Nipple 1/4 ‘ NPT (M) x 1/4’ NPS (M)
H-2008
11
Nipple 3/8’ NPT (M) x 3/8’ NPT (M)
AD-11
(BSP) Nipple 1/4 ‘ NPT (M) x 1/4’ BSP (M)
2101004
Nipple 3/8’ NPT (M) x 3/8’ BSP (M)
2101007
(NPS) Nipple 3/8‘ NPT (M) x 1/4’ NPS (M)
83-4233
Street Elbow 3/8’ NPT (F) x 3/8’ (M) S.S
SSP-1939
(BSP) Nipple 3/8‘ NPT (M) x 1/4’ BSP (M)
2101005
12
Catalogue 2015
23
57
DVFR-1 Filter Regulator
Specification
Air Inlet Thread
1/2” BSP (F)
Regulated Outlets
3 Valved
Unregulated Outlets
N/A
Air Outlets (Ball Valves)
1/ 4” BSP (M)
Width (Overall)
175mm (6.9”)
Height (Overall)
280mm (11”)
Weight
2500 gms (88oz)
Capacity (maximum air flow)
3500 l/min (124cfm)
Maximum Air Inlet Pressure
13 bar (189 psi)
Maximum Regulated Outlet Pressure
0-8 bar (0-116psi)
Pressure Gauge
0-11 bar (0-160 psi)
Gauge port
1/8” BSP (F)
Air Filtration
Down to 5 microns
Drain Valve
Semi-Automatic
Maximum Pressure Drop
5% of Inlet Pressure
Part No
Description
DVFR-1
3 Outlet Filter Regulator (90 cfm)
DV-9420601
Filter bowl removal tool
Ref No
Description
Part Number
1
Upper Cover Assembly
DV-9450806
2
Filter (Air)
DV-9451705
3
Metal Filter Bowl
DV-9453301-MET
4
Ball Valve
SER-3414-MF
5
Pressure Gauge
GA-319
6
Isolation Valve
DV-8000035
DVFR-2 Filter Regulator COALESCER
Specification
Air Inlet Thread
1/2” BSP (F)
Regulated Outlets
3 Valved
Unregulated Outlets
N/A
Air Outlets (Ball Valves)
1/ 4” BSP (M)
Width (Overall)
240mm (9.5”)
Height (Overall)
280mm (11”)
Weight
3200 gms (113oz)
Capacity (maximum air flow)
3500 l/min (124cfm)
Maximum Air Inlet Pressure
13 bar (189 psi)
Maximum Regulated Outlet Pressure
0-8 bar (0-116psi)
Pressure Gauge
0-11 bar (0-160 psi)
Gauge port
1/8” BSP (F)
Air Filtration
Down to 0.01 microns *
Drain Valve
Semi-Automatic
Maximum Pressure Drop
10% of Inlet Pressure
* Suitable for Breathing Air
58
Part No
Description
DVFR-2
3 Outlet Filter Regulator Coalescer (50 cfm)
DV-9420601
Filter bowl removal tool
Ref No
Description
Part Number
1
Upper Cover Assembly
DV-9450806
2
Filter (Air)
DV-9451705
3
Metal Filter Bowl
DV-9453301-MET
4
Ball Valve
SER-3414-MF
5
Pressure Gauge
GA-319
6
Fine Filter (Oil)
DV-9451711
7
Isolation Valve
DV-8000035
Catalogue 2015
DVFR-3 Filter Regulator
Specification
Air Inlet Thread
1/2” BSP (F)
Regulated Outlets
2 Valved
Unregulated Outlets
N/A
Air Outlets (Ball Valves)
1/ 4” BSP (M)
Width (Overall)
165mm (6.5”)
Height (Overall)
240mm (9.5”)
Weight
1341 gms (46oz)
Capacity (maximum air flow)
1700 l/min (60cfm)
Maximum Air Inlet Pressure
13 bar (189 psi)
Maximum Regulated Outlet Pressure
0-8 bar (0-116psi)
Maximum Operating Temperature
40°C (104°F)
Pressure Gauge
0-11 bar (0-160 psi)
Gauge port
1/8” BSP (F)
Air Filtration
Down to 20 microns
Drain Valve
Semi-Automatic
Maximum Pressure Drop
5% of Inlet Pressure
Part No
Description
DVFR-3
2 Outlet Filter Regulator (60 cfm)
Ref No
Description
Part Number
1
Upper Cover Assembly
DV-9350811
2
Filter
9351706
3
Metal Filter Bowl
DV-9353301
4
Ball Valve
SER-3414-MF
5
Pressure Gauge
GA-319
DVFR-8 Filter Regulator Coalescer with Activated Carbon Filter
Specification
Air Inlet Thread
1/2” BSP (F)
Regulated Outlets
3 Valved
Unregulated Outlets
N/A
Air Outlets (Ball Valves)
1/ 4” BSP (M)
Width (Overall)
305mm (12”)
Height (Overall)
280mm (11”)
Weight
3.3kg
Capacity (maximum air flow)
3500 l/min (124cfm)
Maximum Air Inlet Pressure
13 bar (189 psi)
Maximum Regulated Outlet Pressure
0-8 bar (0-116psi)
Pressure Gauge
0-11 bar (0-160 psi)
Gauge port
1/8” BSP (F)
Air Filtration
Down to 0.01 microns *
Drain Valve
Semi-Automatic
Maximum Pressure Drop
10% of Inlet Pressure
* Suitable for Breathing Air
Catalogue 2015
Part No
Description
DVFR-8
3 Outlet Filter Regulator Coalescer with activated carbon filter
DV-9420601
Filter bowl removal tool
Ref No
Description
Part Number
1
Upper Cover Assembly
DV-9450806
2
Filter (Air)
DV-9451705
3
Metal Filter Bowl
DV-9453301-MET
4
Ball Valve
SER-3414-MF
5
Pressure Gauge
GA-319
6
Fine Filter (Oil)
DV-9451711
7
Isolation Valve
DV-8000035
8
Activated Carbon Filter
DV-9451711-AC
59
60
Ref
No
Description
Part No.
Ref
No
Description
Part No.
1
Air Cap/Retaining ring
SP-100-510-K
13
Connector
SP-611-K
2
Tip (** = 1.0, 1.4, 1.6, 1.8, 2.0, 2.2mm)
SP-200S-**-K
14
Airflow Valve
SP-402-K
3
Separator
SP-623-K5
15
Fluid Inlet Connector and seal
SP-610–K
4
Packing
GTI-445-K2
16
Air Valve Service Kit
SPK-101-K
5
Spreader Valve
SP-401-K
17
Retaining Ring and Seals
SPK-102-K
6
Stud and Screw
GTI-408-K5
18
Spreader/ Cheater Service Kit
GTI-428-K5
7
Needle Adjusting Screw
SP-614-K
19
Circlip
25746-007-K5
8
Spring
SP-622-K5
20
Cup Lid Assembly
KR-4001-B
9
Needle (** = 1.0, 1.4, 1.6, 1.8, 2.0, 2.2mm)
SP-300S-**-K
21
Lid Gasket - Kit of 3
KR-11-K3
10
Airvalve housing + seal
SP-612-K
22
Drip Free Diaphragm - Kit of 5
KR-115-K5
11
Spindle
-
23
Cup
KR-466-K
12
Trigger
SP-617-K
24
Complete Cup
KR-566-1-B
Catalogue 2015
Ref
No
1
Description
Part Number
Ref
No
10
Description
Needle Adjusting Screw
Part Number
GTi-W Air Cap / Retaining ring
GTi-407-115
GTi-414-K
GTi-G Air Cap / Retaining ring
GTi-407-110
11
Valve Assembly
JGK-449-K
PRi Air Cap / Retaining ring
PRi-407-310
12
Trigger
GTI-108
1a
Spring Clip
JGA-156-K5
13
Connector
JGA-158
2
GTi-W Tip (1.3, 1.4 & 1.5mm)
GTi-213-**-K
14
Gun Hook
GFG-6
GTi-G Tip (1.2, 1.3, 1.4 & 1.5mm)
GTi-213-**-K
15
Airflow Valve
GTi-415-K
PRi Tip (1.6, 1.8, 2.0, 2.2 & 2.5mm)
PRi-2-**-K
16
1⁄2 Ltr Gravity Cup Kit
GFC-501
Baffle & Seal
GTi-425-K
17
Cup Lid
GFC-402
Baffle Seal – Kit of 5
GTi-33-K5
18
Drip Check Lid kit of 5
GFC-2-K5
3
4
Packing
GTi-445-K2
19
Filter
KGP-5-K5
5
Spreader Valve
GTi-404-K
20
Circlip
25746-007-K5
6
Stud and Screw
GTi-408-K5
21
Circlip
SST-8434-K5
7
GTi Needle
GTi-413-K
22
Seal & Pin Kit (+SST8434-K5)
GTi-428-K5
PRi Needle
PRi-3-K
23
Washer
GFC-17-K5
8
Spring and Pad
GTi-409-K5
24
Spring
JGV-262-K5
Service Kit for GTI gravity and suction 12,13,14,15,16,18,20,22 tip
GTI-416-**
Service Kit for PRi - 16,18,20,22,25 tip
PRi-416-**
9
Bushing
GTi-402-K
9a
Seal kit of 5
JGS-72-K5
Catalogue 2015
61
62
Ref. No
Description
Part Number
Ref. No
Description
Part Number
1
GTI-P air cap/retaining ring
GTI-407-123
11
Valve Assembly
JGK-449-K
GTI-S air cap/retaining ring
GTI-407-110
12
Trigger
GTI-108
Connector
JGA-158
1a
Spring Clip
JGA-156-K5
13
2
GTI-P Tip
GTi-213-**-K
14
Airflow Valve
GTI-415-K
GTI-S Tip
GTI-214-**-K
15
Lock Nut
JGA-51-K5
3
Baffle & Seal
GTI-425-K
16
Seal
23165-001
3a
Baffle seal—Kit of 5
GTI-33-K5
17
Fluid Inlet Connector and seal
JGA-159-K
4
Packing
GTi-445-K2
18
Cup lid assembly
KR-4001-B
5
Spreader Valve
GTI-405-K
19
Lid Gasket - kit of 3
KR-11-K3
6
Stud and Screw
GTI-408-K5
20
Drip free diaphragm - kit of 5
KR115-K5
7
GTI-P needle
GTi-449-**-K
21
Cup
KR-466-K
GTi-S needle (for GTI-214 Tip)
GTI-420-K
22
Complete cup
KR-566-1-B
8
Spring and Pad
GTI-409-K5
23
Circlip
25746-007-K5
9
Bushing
GTI-402-K
24
Circlip
SST-8434-K5
9a
Seal kit of 5
JGS-72-K5
25
Seal & Pin Kit
GTI-428-K5
10
Needle Adjusting Screw
GTI-414-K
26
Spring
JGV-262-K5
Catalogue 2015
Ref. No
Description
Part Number
Ref. No
Description
Part Number
1 (SRi)
Air Cap/Retaining ring Trans-Tech
SRI-407-210
11
Air Valve Assembly
SRI-404-K
SRI-407-200
12
Air Valve Stem Assembly
-
1 (SRiW)
Air Cap/Retaining ring HVLP
SRI-407-215
13
Trigger Stud and Screw Kit
SRI-412-K
2
3
Tip 0.7 mm & seal
SRI-2-07-K
14
Trigger
SRI-9-K
Tip 0.8 mm & seal
SRI-2-08-K
15 (SRi)
Air Inlet Adaptor
SRI-20-K
Tip 1.0 mm & seal
SRI-2-10-K
15 (SRiW)
Air Inlet Adaptor
SRI-40-K
Tip 1.2 mm & seal
SRI-2-12-K
16
Blanking Plug (to replace airflow valve)
SRI-21
Needle for 1.0 and 1.2 mm Tip
SRI-3-K
17
Airflow Valve
SRI-402-K
Needle for 0.7 and 0.8 mm Tip
SRI-37-K
18
Cup
SRI-510
4
Needle Spring
SRI-18-K2
19
Aircap Seal
SRI-35-K5
5
Needle Adjusting Knob
SRI-19-K2
20
Airvalve Spring
SRI-23-K2
6 (SRi)
Spreader Valve
SRI-401-K
21
Airvalve Seal
-
6 (SRiW)
Spreader Valve
SRI-415-K
22
Retaining Ring
-
7
Body Bushing and Seal Kit
SRI-17-K
23
Filter
SRI-42-K3
8
Seal
SRI-16-K5
24
Airvalve Body
-
25
Drip Check Lid Kit of 5
GFC-2-K5
Service Kit for SRi/SRI-W
SRI-416
9
Separator
SRI-6-K5
10
Needle Packing Kit of 3
SRI-411-K3
Catalogue 2015
63
64
Ref No
Description
1
Air Cap Retaining Clip
Ref No
Description
JGA-156-K5
2
Part No.
14
Colour ID Ring Kit (4 Colours)
SN-26-K4
Part No.
Suction Feed Trans-tech® Aircap
VRIPRO-100-TV1-K
15
Airflow Valve
ADV-401-K
Pressure Feed Trans-tech® Aircap
VRIPRO-100-TV2-K
16
Fluid Inlet Connector and seal
ADV-7-K
3
Air Cap Retaining Ring & Seals
ADV-403-K
17
Cup lid assembly
KR-4001-B
4
Fluid Tip - 0.85,14, 16, 18
SP-200S-**-K
18
Lid Gasket - kit of 3
KR-11-K3
5
Separator
SP-626-K5
19
Drip free diaphragm - kit of 5
KR115-K5
6
Body Bushing & Seal
SN-6-K
20
Cup
KR-466-K
7
Fluid Needle - 0.85, 1.4, 1.6, 1.8 mm
ADV-310-**-K
21
Complete cup
KR-566-1-B
8
Fluid Adjusting Knob, Spring & Pad Kit
ADV-6-K
22
Filter
KR-484-K10
9
Spreader Valve Assembly
ADV-401-K
23
Torx Key
SPN-8-K2
10
Packing, Spring & Packing Nut Kit
SN-404-K
24
Trigger Stud & Torx Screw (kit of 5)
SN-405-K5
11
Air Valve Replacement Kit
SN-402-K
Service Parts
12
Trigger, Stud & Screw Kit
SN-63-K
Spray Gun repair kit
PRO-415-1
13
Air Inlet
SN-9-K
Seal and Pin Kit, kit of 5
GTI-428-K5
Catalogue 2015
Ref No
Description
Ref No
Description
1
Air Cap Retaining Clip
JGA-156-K5
14
Colour ID Ring Kit (4 Colours)
SN-26-K4
2
Gravity Feed Trans-tech® Air Cap
VRIPRO-100-TV1-K
15
Airflow Valve
ADV-401-K
3
Air Cap Retaining Ring & Seals
ADV-403-K
16
Gravity Cup Kit
GFC-501
4
Fluid Tip 12 or 13
SP-200S-XX-K
17
Drip Check Lid (kit of 5)
GFC-2-K5
5
Separator
SP-626-K5
18
Gravity Cup Lid
GFC-402
6
Body Bushing & Seal
SN-6-K
19
Filter
KGP-5-K5
7
Fluid Needle 12 or 13
ADV-310-**-K
20
Spanner, Torx, Brush & ID Rings
SN-406
8
Fluid Adjusting Knob, Spring & Pad Kit
ADV-6-K
21
Torx Key
SPN-8-K2
9
Spreader Valve Assembly
ADV-402-K
22
Trigger Stud & Torx Screw (kit of 5)
SN-405-K5
10
Packing, Spring & Packing Nut Kit
SN-404-K
Service Parts
11
Air Valve Replacement Kit
SN-402-K
Spray Gun repair kit
PRO-415-1
12
Trigger, Stud & Screw Kit
SN-63-K
Seal and Pin Kit, kit of 5
GTI-428-K5
13
Air Inlet
SN-9-K
Catalogue 2015
Part No.
Part No.
65
66
Ref.
No
Description
Part No.
Ref.
No
Description
Part No.
1
Air Cap/Retaining ring (* = 186+ or 30+)
AV-4239-***
12
Trigger
GTI-108
1a
Spring Clip - Kit of 5
JGA-156-K5
13
Connector
JGA-158
2
Tip (* = EX-1.8mm, FF-1.4mm, FW-1.6mm)
AV-645-*
14
Airflow Valve
GTI-415-K
3
Baffle & Seal
JGD-402-K
15
Lock Nut - Kit of 5
JGA-51-K5
3a
Baffle seal - Kit of 5
GTI-33-K5
16
Seal
23165-001
4
Packing
GTi-445-K2
17
Fluid Inlet Connector and seal
JGA-159-K
5
Spreader Valve
GTI-405-K
18
Cup lid assembly
KR-4001-B
6
Stud and Screw
GTI-408-K5
19
Lid Gasket - kit of 3
KR-11-K3
7
Needle (*= DEX, FF or FW)
JGA-421*-K
20
Drip free diaphragm - kit of 5
KR115-K5
8
Spring - Kit of 5
GTI-409-K5
21
Cup
KR-466-K
9
Bushing
JGA-17
22
Complete cup
KR-566-1-B
9a
Seal - Kit of 5
JGS-72-K5
23
Circlip
25746-007-K5
10
Needle Adjusting Screw
GTI-414-K
24
Circlip
SST-8434-K5
11
Valve Assembly
JGK-449-K
25
Seal & Pin Kit ( + SST-8434-K5)
GTI-428-K5
26
Spring
JGV-262-K5
Catalogue 2015
Ref
No
Description
Part Number
Ref
No
Description
Part Number
1
Air Cap/Retaining ring * = 186 or 30
AV-4239-*
12
Trigger
GTI-108
1a
Spring Clip
JGA-156-K5
13
Connector 1/4
JGA-158
2
Tip (* = EX-1.8mm, FF-1.4mm, FW-1.6mm)
AV-645-*
14
Gun Hook
GFG-6
3
Baffle & Seal
JGD-402-K
15
Airflow Valve
GTI-415-K
4
Packing (kit of 2)
GTi-445-K2
16
1/2 Ltr Gravity Cup Kit
GFC-501
5
Spreader Valve
GTI-404-K
17
Cup Lid
GFC-402
6
Stud and Screw
GTI-408-K5
18
Drip Check Lid kit of 5
GFC-2-K5
7
Needle (* = DEX or FF)
JGA-421-*-K
19
Filter
KGP-5-K5
8
Spring
GTI-409-K5
20
Circlip
25746-007-K5
9
Bushing
JGA-17
21
Circlip
SST-8434-K5
9a
Seal - kit of 5
JGS-72-K5
22
Seal & Pin Kit
GTI-428-K5
10
Needle Adjusting Screw
GTI-414-K
23
Washer
GFC-17-K5
11
Valve Assembly
JGK-449-K
24
Spring
JGV-262-K5
Catalogue 2015
67
68
Ref
No
Description
Part Number
Part Number
Visor Assembly (Ref Nos 2-10)
MPV-526
Ref
No
Description
1
2
Quick Detachable Stem
MPV-20
12
Quick Detachable Connector
MPV-442
3
Clear Visor (kit of 5)
MPV-478-K5
13
Regulator and Housing
MPV-455
4
Visor Covers (kit of 10)
MPV-44-K10
14
Disposable Filter
MPV-22
5
Face Cartridge — Foam (kit of 5)
MPV-476-K5
15
Waistbelt and Filter Housing
MPV-519
6
Face Cartridge — Synthetic (kit of 5)
MPV-477-K5
16
Quick Detachable Stem
MPV-10
7
Neck Covers (kit of 5)
MPV-24-K5
17
Quick Detachable Connector
MPV-424
8
Hoods (kit of 5)
MPV-2-K5
18
10m length M-F QD Fittings
H-6085-QD
9
Stowage Bag
MPV-458
10m length 1/4” Re-usable Fittings
H-6065-B
10
Tube and Diffuser Assembly
MPV-457
19
Gun Hose Assembly
MPV-456
11
Waistbelt Assembly
MPV-518
20
Quick Detachable Stem
MPV-5
Catalogue 2015
Ref No
Description
Part
Number
Ref No
Description
Part
Number
1
Face mask assembly (Ref Nos 2-8)
MPV-517
10
Regulator and housing
MPV-455
2
Browguard assembly
MPV-453
11
Disposable filter
MPV-22
3
Face mask & seal assembly
MPV-454
12
Waistbelt and filter housing
MPV-519
4
Kit of 10 face mask covers
MPV-1-K10
13
Quick detachable stem
MPV-10
5
Kit of 5 neck covers
MPV-24-K5
14
Quick detachable connector
MPV-424
6
Kit of 5 hoods
MPV-2-K5
15
Gun hose assembly
MPV-456
7
Tube and diffuser assembly
MPV-457
16
Quick detachable assembly
MPV-5
8
Quick detachable stem
MPV-20
17
Stowage bag
MPV-458
9
Quick detachable connector
MPV-442
18
Waistbelt assembly
MPV-518
Catalogue 2015
69
WATERBASED
PRIMER FILLER
2K HS VOC PRIMER
FILLER
2K ETCH PRIMER
FILLER
HS 2K Primer
HC Primer 1K
HS Wet & Dry Sanding
Filler
HS 2K Primer
-
-
1.6 - 1.8 mm
1.6 - 1.8 mm
-
P1 (Trans-Tech)
1.3 mm
1.3 mm
1.3 mm
-
-
1.3 mm
H1 (HVLP)
1.4 mm
(2.2 bar)
-
1.4 mm
(2.2 bar)
-
-
1.4 mm
(2.2 bar)
T1 (Trans-Tech)
1.4 mm
(2.2 bar)
1.4 mm
(2.2 bar)
1.4 mm
(2.2 bar)
-
-
-
T2 (Trans-Tech)
1.4 mm
(2.2 bar)
-
1.4 mm
(2.2 bar)
-
-
-
T110 (Trans-Tech)
0.8 mm
0.8 mm
-
-
-
HS1 (HVLP)
-
-
-
-
-
SPRAY GUN SET UP SELECTOR: Gun Inlet Pressure 2.0 bar or as stated
Lackdatenblatt: Eingangsdruck: ca. 2.0 bar wie unten angegeben
PISTOLET ET TABLEAU DES REGLAGES: Pression à l’entrée du pistolet 2.0 bar ou comme indiqué
SCHEDA ALLESTIMENTO AEROGRAFO: pressione aria 2,0 bar o come indicato
CONFIGURACIONES DE PISTOLAS: Presión a la entrada de la pistola 2.0 bar o según lo indicado
WET ON WET PRIMER
FILLER
Hydrocolor
-
TS1 (Trans-Tech)
WATERBORNE
BASECOAT
Brilliant Clear VOC
Proclear
VOC Duraclear
DeVilbiss Automotive Refinishing UK: +44 (0) 1202 571111 F: +33 (0) 4 75 75 27 80 D: +49 (0) 6074 403 251 Web: http://www.devilbisseu.com
COMPLIANT DIRECT
GLOSS AND CLEAR
P1 1.6-1.8
1-70 white and grey
8-145 2K HS grey
“Epoxy Primer Wet
on Wet”
Solid Colour 2K LD
Clearcoat
waterbase
topcoat
"HS Surfacer 2K
Wet on Wet"
HS Surfacer 2K
P1 1.6-1.8
1-7510/7520
Epoxy Primer
-
-
-
-
-
-
TE10 - 1.3
TE20 - 1.3
TE20 - 1.3
TE20 - 1.3-1.4
TE20 - 1.3-1.4
TE20 - 1.3-1.4
TE20 - 1.3-1.4
-
TE20 - 1.3-1.4
TE20 - 1.3-1.4
TE20 - 1.3-1.4
-
-
-
-
-
-
H1/T1/T110 1.3
-
-
-
-
-
TE20 - 1.3-1.4
-
-
-
-
-
BASE
-
-
-
-
-
CLEAR
T2 1.3
T2 1.3
T2 1.3-1.4
T2 1.3-1.4
T2 1.3-1.4
T2 1.3-1.4
-
T2 1.3-1.4
T2 1.3-1.4
T2 1.3-1.4
T2 1.3-1.4
-
-
-
-
-
-
CLEAR
DeVilbiss Automotive Refinishing UK: +44 (0) 1202 571111 F: +33 (0) 4 75 75 27 80 D: +49 (0) 6074 403 251 Web: http://www.devilbisseu.com
-
-
Series 3000
Series 3000 BEROTHANE
HS420
-
8-414 HS420 Clearcoat
-
8-214 HS Scratch
Resistant Clearcoat
-
-
8-104 HS Clearcoat
8-314 HS 420 Speed Clear
-
-
-
30-746/74640
Series 900, 900+
-
-
8-145/40 2K HS black
-
-
8-145/10 2K HS white
-
-
-
P1 1.6-1.8
8-145/40 2K HS black
-
-
-
-
-
BASE
8-145 2K HS grey
P1 1.6-1.8
8-145/10 2K HS white
P1 1.6-1.8
P1 1.4-1.6
1-15 / 1-17
Wash Primer
PRIMER
MATERIAL
CATEGORY
TS1 1.0-1.2
TS1 1.0-1.2
TS1 0.8-1.0
TS1 0.8-1.0
TS1 0.8-1.0
TS1 1.0-1.2
HS1/TS1 1.0-1.2
TS1 1.0-1.2
TS1 1.0-1.2
TS1 1.0-1.2
TS1 1.0-1.2
TS1 1.0-1.2
TS1 1.0-1.2
TS1 1.0-1.2
TS1 1.0-1.2
TS1 1.0-1.2
TS1 0.8-1.0
SMART
SPRAY GUN SET UP SELECTOR: Gun Inlet Pressure 2.0 bar or as stated
Lackdatenblatt: Eingangsdruck: ca. 2.0 bar wie unten angegeben
PISTOLET ET TABLEAU DES REGLAGES: Pression à l’entrée du pistolet 2.0 bar ou comme indiqué
SCHEDA ALLESTIMENTO AEROGRAFO: pressione aria 2,0 bar o come indicato
CONFIGURACIONES DE PISTOLAS: Presión a la entrada de la pistola 2.0 bar o según lo indicado
Primers
CATEGORY
CC6300 VOC Protect Clear
3750S-3760S Ultra
Productive VOC Clear
Cromax® Pro Waterborne
Basecoat
Cromax® Waterborne
Basecoat
Centari® 6000 Low
Emission Basecoat
Centari® 5035 Low
Emission 2K Topcoat
NS2602-NS2607 Non
Sanding Primer Surfacer
PS1061-PS1064-PS1067
Cromax Pro Surfacer
1051R/1057R High
Productive Surfacer
901R/907R Universal 2K
Plastic Primer
825R Wash Primer
Surfacer
635R Etching Primer
MATERIAL
-
-
-
-
-
-
-
P1-1.4
P1-1.6/1.8
P1-1.6/1.8
P1-1.4
P1-1.4
P1-1.4
PRIMER
-
-
-
-
TE10/TE20 - 1.2/1.3
TE20-1.2/1.3
TE20-1.2/1.3
TE20-1.2/1.3
TE10-1.3
-
-
-
-
-
BASE
TE20-1.2/1.3
TE20-1.2/1.3
TE20-1.2/1.3
TE20-1.2/1.3
TE20-1.2/1.3
-
-
-
TE20-1.2/1.3
TE10-1.3
-
-
-
-
-
CLEAR
-
-
-
-
-
T2-1.2/1.3
T2-1.2/1.3
T2-1.2/1.3
T2-1.2/1.3
T1-1.3
-
-
-
-
-
BASE
T2-1.2/1.3
T2-1.2/1.3
T2-1.2/1.3
T2-1.2/1.3
T2-1.2/1.3
-
-
-
T2-1.2/1.3
T1-1.3
-
-
-
-
-
CLEAR
HS1/TS1-1.0/1.2
HS1/TS1-1.0/1.2
HS1/TS1-1.0/1.2
HS1/TS1-1.0/1.2
HS1/TS1-1.0/1.2
HS1/TS1-1.0/1.2
HS1/TS1-1.0/1.2
HS1/TS1-1.0/1.2
HS1/TS1-1.0/1.2
TS1-0.8
TS1-1.0/1.2
TS1-1.0/1.2
TS1-0.8
TS1-0.8
TS1-0.8
SMART
SPRAY GUN SET UP SELECTOR: Gun Inlet Pressure 2.0 bar or as stated
Lackdatenblatt: Eingangsdruck: ca. 2.0 bar wie unten angegeben
PISTOLET ET TABLEAU DES REGLAGES: Pression à l’entrée du pistolet 2.0 bar ou comme indiqué
SCHEDA ALLESTIMENTO AEROGRAFO: pressione aria 2,0 bar o come indicato
CONFIGURACIONES DE PISTOLAS: Presión a la entrada de la pistola 2.0 bar o según lo indicado
Non Sanding
SURFACERS
CC6400 Standard VOC Clear
-
-
Clearcoats
Solventborne
Basecoat
Waterborne
Basecoat
SURFACERS
2k Single Stage
CC6600 Cromax Pro Star
Clear
-
DeVilbiss Automotive Refinishing UK: +44 (0) 1202 571111 F: +33 (0) 4 75 75 27 80 D: +49 (0) 6074 403 251 Web: http://www.devilbisseu.com
CC6700 Ultra Performance
Energy Clear
TE10 1.2-1.3
-
-
1.6-1.8
1.6-1.8
1.8-2.0
-
Plastic Primer
Epoxy Primer
4:1 Primer
5:1 HS Primer
UHS
SR
ETAVALUE
Base
Clear
-
-
-
-
-
-
-
-
-
BASE
T1 1.3 / T2 1.3
T1 1.3 / T2 1.3
T1 1.3 / T2 1.3
-
-
-
-
T1 1.2-1.3
-
CLEAR
DeVilbiss Automotive Refinishing UK: +44 (0) 1202 571111 F: +33 (0) 4 75 75 27 80 D: +49 (0) 6074 403 251 Web: http://www.devilbisseu.com
TE10 1.3/ TE20 1.3
TE10 1.3/ TE20 1.3
TE10 1.3/ TE20 1.3
-
-
-
1.4-1.6
1K Primer
Primer/Filler
CLEAR
BASE
MATERIAL
CATEGORY
PRIMER
TS1 0.8-1.0
TS1 0.8-1.0
TS1 0.8-1.0
-
-
TS1 1.0-1.2
-
TS1 0.8-1.0
TS1 1.0-1.2
SMART
SPRAY GUN SET UP SELECTOR: Gun Inlet Pressure 2.0 bar or as stated
Lackdatenblatt: Eingangsdruck: ca. 2.0 bar wie unten angegeben
PISTOLET ET TABLEAU DES REGLAGES: Pression à l’entrée du pistolet 2.0 bar ou comme indiqué
SCHEDA ALLESTIMENTO AEROGRAFO: pressione aria 2,0 bar o come indicato
CONFIGURACIONES DE PISTOLAS: Presión a la entrada de la pistola 2.0 bar o según lo indicado
Primers
Polyester
CATEGORY
Primer Filler 285-
Etch Primer Filler 283-150
VOC
UP Polyester Spray Filler
1006-26
MATERIAL
P1-1.6/1.8 @ 2.0 Bar
P1-1.6/1.8 @ 2.0 Bar
P1-2.5 @ 2.0 Bar
PRIMER
-
-
-
BASE
-
-
-
CLEAR
-
-
-
-
BASE
-
-
H1-1.3 @ 2.0 Bar
T1-1.3/1.4 @ 2.2 Bar
T2-1.3/1.4 @ 2.2 Bar
-
CLEAR
-
-
-
-
SMART
1.6 - 1.8 @ 2.0 BAR
1.6 - 1.8 @ 2.0 BAR
1.6 - 1.8 @ 2.0 BAR
-
GPi
SPRAY GUN SET UP SELECTOR: Gun Inlet Pressure 2.0 bar or as stated
Lackdatenblatt: Eingangsdruck: ca. 2.0 bar wie unten angegeben
PISTOLET ET TABLEAU DES REGLAGES: Pression à l’entrée du pistolet 2.0 bar ou comme indiqué
SCHEDA ALLESTIMENTO AEROGRAFO: pressione aria 2,0 bar o come indicato
CONFIGURACIONES DE PISTOLAS: Presión a la entrada de la pistola 2.0 bar o según lo indicado
Fillers
-
-
-
-
-
P1-1.6/1.8 @ 2.0 Bar
H1-1.3 @ 2.0 Bar
T1-1.3/1.4 @ 2.2 Bar
T2-1.3/1.4 @ 2.2 Bar
T110-1.3/1.4 @ 2.0 Bar
HS1-1.0/1.2 @ 1.5-2.0 Bar
TS1-1.0/1.2 @ 1.5-2.0 Bar
-
1K-Primer Filler 176-72
-
H1-1.3 @ 2.0 Bar
T1-1.3/1.4 @ 2.2 Bar
T2-1.3/1.4 @ 2.2 Bar
T110-1.3/1.4 @ 2.0 Bar
HS1-1.0/1.2 @ 1.5-2.0 Bar
TS1-1.0/1.2 @ 1.5-2.0 Bar
-
-
-
-
HS1-1.0/1.2 @ 1.5-2.0 Bar
TS1-1.0/1.2 @ 1.5-2.0 Bar
P1-1.4 @2.0 Bar
TE10-1.3/1.4 @ 2.0 Bar
TE20-1.3/1.4 @ 2.0 Bar
HV30-1.3 @ 1.75 Bar
H1-13 @ 2.0 Bar
T2-1.4 @ 2.2 Bar
-
TE10-1.3/1.4 @ 2.0 Bar
TE20-1.3/1.4 @ 2.0 Bar
HV30-1.3 @ 1.75 Bar
-
-
H1-13 @ 2.0 Bar
T2-1.4 @ 2.2 Bar
Non-Sanding-Filler 285VOC
TE20-1.4 @ 2.0 Bar
HV30-13 @ 1.75 Bar
-
Non Sanding
Primer
-
TE20-1.4 @ 2.0 Bar
HV30-13 @ 1.75 Bar
-
55-Line Basecoat
-
HS/VOC 2K-Topcoat 22-
Solventborne
Basecoat
90-Line Basecoat
2K Single Stage
Waterborne
Basecoat
-
-
HS1-1.0/1.2 @ 1.5-2.0 Bar
TS1-1.0/1.2 @ 1.5-2.0 Bar
HS / VOC Clearcoat 923-
-
CLEARCOATS
DeVilbiss Automotive Refinishing UK: +44 (0) 1202 571111 F: +33 (0) 4 75 75 27 80 D: +49 (0) 6074 403 251 Web: http://www.devilbisseu.com
H1-1.3 @ 2.0 Bar
T1-1.3/1.4 @ 2.2 Bar
T2-1.3/1.4 @ 2.2 Bar
T110-1.3/1.4 @ 2.0 Bar
TE10-1.3/1.4 @ 2.0 Bar
TE20-1.3/1.4 @ 2.0 Bar
HV30-1.3 @ 1.75 Bar
Clear
Base
Primer
CATEGORY
-
-
-
-
-
-
GYSO Gold Clear
GYSO Eco Clear
Top Klarlack S80
TE20-1,3/TE10-1,3
TE20-1,3/TE10-1,3
TE20-1,3/TE10-1,3
-
-
-
-
-
-
-
-
BASE
T2-1,3 / T1-1,3
T2-1,3 / T1-1,3
T2-1,3 / T1-1,3
-
-
-
-
CLEAR
DeVilbiss Automotive Refinishing UK: +44 (0) 1202 571111 F: +33 (0) 4 75 75 27 80 D: +49 (0) 6074 403 251 Web: http://www.devilbisseu.com
-
-
-
-
P1-1,4
-
-
No sanding
-
CLEAR
-
P1-2,0
P1-1,8/1,6
Premium Füller
G20/G21/G22
Standard
BASE
Dickschicht
PRIMER
MATERIAL
TS1-1,0/1,2/1,4
TS1-1,0/1,2/1,4
TS1-1,0/1,2/1,4
-
TS1- 1,0/0,8
-
TS1- 1,2/1,4
SMART
SPRAY GUN SET UP SELECTOR: Gun Inlet Pressure 2.0 bar or as stated
Lackdatenblatt: Eingangsdruck: ca. 2.0 bar wie unten angegeben
PISTOLET ET TABLEAU DES REGLAGES: Pression à l’entrée du pistolet 2.0 bar ou comme indiqué
SCHEDA ALLESTIMENTO AEROGRAFO: pressione aria 2,0 bar o come indicato
CONFIGURACIONES DE PISTOLAS: Presión a la entrada de la pistola 2.0 bar o según lo indicado
primers & fillers
basecoats
topcoat
medium solids
clears
Kapci 810 Epoxy Primer
Kapci 880 2K Epoxy primer
Kapci 805 2K Wash primer
Kapci 800 1K Etch primer
Kapci 633 2K filler
Kapci 630 2K filler
Kapci 625 2K filler
GTi Pro
GTi Pro
GTi Pro
GTi Pro
GTi Pro
1.8 - 2.2 mm
1.6 - 1.8 mm
1.6 - 1.8 mm
1.6 - 1.8 mm
1.6 - 1.8 mm
1.6 - 1.8 mm
1.6 - 1.8 mm
P1 (Trans-Tech)
1.3 - 1.4 mm
1.3 - 1.4 mm
1.3 - 1.4 mm
1.2 - 1.3 mm
1.2 - 1.3 mm
1.2 - 1.3 mm
PRi
PRi
PRi
PRi
PRi
PRi
PRi
H1 (HVLP)
1.3 - 1.4 mm
1.3 - 1.4 mm
1.3 - 1.4 mm
1.3 - 1.4 mm
1.2 - 1.3 mm
1.2 - 1.3 mm
1.2 - 1.3 mm
PRi
-
-
-
-
-
-
T1 (Trans-Tech)
1.3 - 1.4 mm
1.3 - 1.4 mm
1.3 - 1.4 mm
1.3 - 1.4 mm
1.3 - 1.4 mm
1.2 - 1.3 mm
1.2 - 1.3 mm
1.2 - 1.3 mm
PRi
-
-
-
-
-
-
T2 (Trans-Tech)
1.3 - 1.4 mm
1.3 - 1.4 mm
1.3 - 1.4 mm
1.3 - 1.4 mm
1.3 - 1.4 mm
1.2 - 1.3 mm
1.2 - 1.3 mm
1.2 - 1.3 mm
PRi
-
-
-
-
-
-
T110 (Trans-Tech)
1.0 - 1.2 mm
1.0 - 1.2 mm
1.0 - 1.2 mm
1.0 - 1.2 mm
0.8 - 1.0 mm
0.8 - 1.0 mm
0.8 - 1.0 mm
0.8 - 1.0 mm
-
-
-
-
-
-
-
HS1 (HVLP)
1.0 - 1.2 mm
1.0 - 1.2 mm
1.0 - 1.2 mm
1.0 - 1.2 mm
0.8 - 1.0 mm
0.8 - 1.0 mm
0.8 - 1.0 mm
0.8 - 1.0 mm
-
-
-
-
-
-
-
SPRAY GUN SET UP SELECTOR: Gun Inlet Pressure 2.0 bar or as stated
Lackdatenblatt: Eingangsdruck: ca. 2.0 bar wie unten angegeben
PISTOLET ET TABLEAU DES REGLAGES: Pression à l’entrée du pistolet 2.0 bar ou comme indiqué
SCHEDA ALLESTIMENTO AEROGRAFO: pressione aria 2,0 bar o come indicato
CONFIGURACIONES DE PISTOLAS: Presión a la entrada de la pistola 2.0 bar o según lo indicado
Kapcibase 640 solid colour
basecoat
GTi Pro
1.3 - 1.4 mm
1.3 - 1.4 mm
TS1 (Trans-Tech)
Kapcibase 670 basecoats
GTi Pro
1.3 - 1.4 mm
Kapci Dima 9670
Waterborne basecoats
Kapcicyl 660 2K Acrylic
mixing system
Kapci 888 2K MS Acrylic
clear coat
GTi Pro
1.0 - 1.2 mm
1.0 - 1.2 mm
1.0 - 1.2 mm
1.0 - 1.2 mm
1.0 - 1.2 mm
1.3 - 1.4 mm
1.3 - 1.4 mm
1.0 - 1.2 mm
1.3 - 1.4 mm
1.3 - 1.4 mm
-
1.3 - 1.4 mm
1.3 - 1.4 mm
1.4 mm
1.3 - 1.4 mm
1.3 - 1.4 mm
-
GTi Pro
GTi Pro
-
DeVilbiss Automotive Refinishing UK: +44 (0) 1202 571111 F: +33 (0) 4 75 75 27 80 D: +49 (0) 6074 403 251 Web: http://www.devilbisseu.com
GTi Pro
Kapci 3001 2K MS Acrylic
clear coat
Kapci 3200 2K MS Acrylic
clear coat
Kapci 3300 2K MS Extra fast
drying acrylic clear coat
Kapci 9999 2K MS Acrylic
clear coat
Kapci 9999CN 2K MS Fast
drying acrylic clear coat
Kapci 6100 2K HS Acrylic
high solids clears clear
coat Low VOC
SPOT REPAIRS
SOLVENTBORNE
BASECOAT
WATERBORNE
BASECOAT
CLEARCOATS
2K SOLID COLOURS
NON SANDING
PRIMER
FILLERS
Smooth Surfacer
WASH PRIMER
POLYESTER
CATEGORY
-
Klar Top Clear
LM-12-1
-
-
-
-
-
-
-
-
-
-
TE10/TE20 1,2 - 1,3 mm
1,8 - 2,0 bar
TE10/TE20 1,2 - 1,3 mm
1,8 - 2,0 bar
TE10/TE20 1,2 - 1,3 mm
1,8 - 2,0 bar
TE10/TE20 1,2 - 1,3 mm
1,8 - 2,0 bar
-
-
-
-
-
TE10/TE20 1,2 - 1,3 mm
1,8 - 2,0 bar
TE20/HV30 1,2 - 1,3 mm
1,8 - 2,0 bar
TE20/HV30 1,2 - 1,3 mm
1,8 - 2,0 bar
-
-
-
-
-
-
-
TE110/T1/T2 1,3 - 1,4 mm
1,8 - 2,0 bar
T1/H1 1,2 - 1,3 mm
1,8 - 2,0 bar
T1/H1 1,2 - 1,3 mm
1,8 - 2,0 bar
-
-
-
-
HS1 0,8 mm
1,3 - 1,8 bar
TS1 1,0 mm
1,3 - 1,8 bar
-
-
-
-
-
TE110/T1/T2 1,3 - 1,4 mm
1,8 - 2,0 bar
TE110/T1/T2 1,3 - 1,4 mm
1,8 - 2,0 bar
TE110/T1/T2 1,3 - 1,4 mm
1,8 - 2,0 bar
TE110/T1/T2 1,3 - 1,4 mm
1,8 - 2,0 bar
-
-
-
-
-
-
-
-
-
SMART
-
-
-
-
-
-
TE110/T1 1,3 - 1,4 mm
1,5 - 2,0 bar
-
-
-
TE110/T1 1,3 - 1,4 mm
1,5 - 2,0 bar
-
-
CLEAR
-
BASE
DeVilbiss Automotive Refinishing UK: +44 (0) 1202 571111 F: +33 (0) 4 75 75 27 80 D: +49 (0) 6074 403 251 Web: http://www.devilbisseu.com
-
-
L-13-1
Clearcoats
-
L-12-1
-
-
Aqua Base
SB/WB basecoat
-
-
1,6 - 1,8 mm
1,5 - 2,0 bar
1,6 - 1,8 mm
1,5 - 2,0 bar
1,6 - 1,8 mm
1,5 - 2,0 bar
-
-
TE10/TE20 1,2 - 1,3 mm
1,5 - 2,0 bar
-
-
-
1,8 - 2,0 mm
1,5 - 2,0 bar
-
-
CLEAR
TE10 1,3 - 1,4 mm
1,5 - 2,0 bar
-
BASE
-
2,0 - 2,5 mm
1,5 - 2,0 bar
PRIMER
Klar Special Coatings 1K
Klar Special Coatings 2K
GF-11-3
GF-11-2
GF-11-1
GF-11-3 WoW
Polyester Based Primer
GPH-30.1
Polyester Spray Filler
MATERIAL
SPRAY GUN SET UP SELECTOR: Gun Inlet Pressure 2.0 bar or as stated
Lackdatenblatt: Eingangsdruck: ca. 2.0 bar wie unten angegeben
PISTOLET ET TABLEAU DES REGLAGES: Pression à l’entrée du pistolet 2.0 bar ou comme indiqué
SCHEDA ALLESTIMENTO AEROGRAFO: pressione aria 2,0 bar o come indicato
CONFIGURACIONES DE PISTOLAS: Presión a la entrada de la pistola 2.0 bar o según lo indicado
POLYESTER
CATEGORY
04804 MAC 85
MACROFAN HS ISOSEALER
04302/06/10 MACROFAN
AUTOLEVEL PRIMER
04806/10 MACROFAN
RAPID FILLER
04706/10 MACROFAN HS
HIGTFILLER
04384 -EPOFAN PRIMER
R-EC
05781 - CLEARPRIMER
05720 - MONOPRIMER
04363 - UNIVERSAL
PRIMER
04318 -FIX-O-DUR
04210 - POLYFAN RUSH
MATERIAL
P1 - 1,6/1,8
P1 - 1,6/1,8
P1 - 1,4/1,8
P1 - 1,4/1,8
P1 -1,6/1,8
P1-1,4
P1-1,4
P1-1,4
P1-1,4
P1-1,4
P1 - 2,0/2,5
PRIMER
-
-
-
-
-
-
-
-
-
-
-
-
BASE
TE 10 -1,3 /1,4
TE 20 - 1,4
-
-
-
-
-
-
-
-
-
-
-
CLEAR
-
-
-
-
-
-
-
-
-
-
-
-
-
BASE
T1/T2 -1,4
T1/T2 -1,4
-
-
-
-
-
T1 - 1,3
T1 - 1,3
T1 - 1,3
T1 - 1,3
T1 - 1,3
-
CLEAR
TS1 -1,0/1,2
TS1 -1,0/1,2
-
-
-
-
-
TS1 1,2
TS1 1,0
TS1 1,2
TS1 1,2
TS1 1,2
-
SMART
SPRAY GUN SET UP SELECTOR: Gun Inlet Pressure 2.0 bar or as stated
Lackdatenblatt: Eingangsdruck: ca. 2.0 bar wie unten angegeben
PISTOLET ET TABLEAU DES REGLAGES: Pression à l’entrée du pistolet 2.0 bar ou comme indiqué
SCHEDA ALLESTIMENTO AEROGRAFO: pressione aria 2,0 bar o come indicato
CONFIGURACIONES DE PISTOLAS: Presión a la entrada de la pistola 2.0 bar o según lo indicado
PRIMER
04384 EPOFAN PRIMER
R-EC
P1-1,4
-
SEALER
FILLER 2K
04384 EPOFAN PRIMER
R-EC
P1-1,4
DeVilbiss Automotive Refinishing UK: +44 (0) 1202 571111 F: +33 (0) 4 75 75 27 80 D: +49 (0) 6074 403 251 Web: http://www.devilbisseu.com
04804 - MAC 85 MACROFAN HS ISOSEALER
-
MC 421 MACROFAN PLUS
UHS 2:1
MC 422 MACROFAN ELITE
UHS 3:1
MC 450 MACROFAN
AUTOGARD UHS 3:1
MAC 1 MACROFAN HS
SYSTEM
MAC 4 MACROFAN UHS
SYSTEM TOP COAT
MAC 5 MACROFAN 1K TOP
COAT
WATERBORNE
TE 10 1,3 - HV30 1,3
-
-
-
-
-
-
-
-
TE 10 1,3/1,4
-
-
BASE
-
TE 20 - 1,3
TE 20 - 1,2/1,3
TE 20 - 1,2/1,3
TE 20 - 1,2/1,3
TE 20 - 1,2/1,3
TE 20 - 1,3
TE 20 -1,2
TE 20 - 1,3
-
TE 10/20 -1,3 /1,4
TE 10 -1,3 /1,4
CLEAR
T1 1,3 - H1 1,3
-
-
-
-
-
-
-
-
T1-1,2/13 H1 -1,3
-
-
BASE
-
T1 - 1,3
T1 - 1,2/1,3
T1 - 1,2/1,3
T1 - 1,2/1,3
T2 - 1,2
T1 - 1,2/1,3
T2 - 1,2
T1 - 1,2/1,3
-
T1/T2 -1,3-1,4
T1/T2 -1,3/1,4
CLEAR
DeVilbiss Automotive Refinishing UK: +44 (0) 1202 571111 F: +33 (0) 4 75 75 27 80 D: +49 (0) 6074 403 251 Web: http://www.devilbisseu.com
-
-
MC 420 MACROFAN UHS
2:1
HYDROFAN BASE COAT
-
MC 411 MACROFAN PROF
UHS 2:1
CLEARCOATS
SOLID COLOR
-
BSB BASE COAT
P1-1,4
04302/06/10 MACROFAN
AUTOLEVEL PRIMER
SOLVENTBORNE
P1-1,4
04122 - MAC 9 - MACROFAN
HI-GARD SEALER
SEALER (continued)
PRIMER
MATERIAL
CATEGORY
TS1 -1,0/1,2 HS1 - 08/1,0
TS1 -1,0/1,2
TS1 -1,0/1,2
TS1 -1,0/1,2
TS1 -1,0/1,2
TS1 -1,0/1,2
TS1 -1,0/1,2
TS1 -1,0/1,2
TS1 -1,0/1,2
TS1 1,2 HS 1- 08/1,0
TS1 -1,0/1,2
TS1 -1,0/1,2
SMART
SPRAY GUN SET UP SELECTOR: Gun Inlet Pressure 2.0 bar or as stated
Lackdatenblatt: Eingangsdruck: ca. 2.0 bar wie unten angegeben
PISTOLET ET TABLEAU DES REGLAGES: Pression à l’entrée du pistolet 2.0 bar ou comme indiqué
SCHEDA ALLESTIMENTO AEROGRAFO: pressione aria 2,0 bar o come indicato
CONFIGURACIONES DE PISTOLAS: Presión a la entrada de la pistola 2.0 bar o según lo indicado
2k HS Primer Filler
2k High Build Filler
2k Filler 540
2k Epoxy Primer
1k Multi Plastic Primer
1k Etch Primer
-
1.4 mm
1.8 mm
1.8 mm
1.8 mm
1.8 mm
1.4 mm
1.4 mm
P1 (Trans-Tech)
1.3 mm
1.3 mm
PRi
PRi
PRi
PRi
PRi
PRi
PRi
H1 (HVLP)
-
1.3 mm
1.3 mm
1.3 mm
PRi
PRi
PRi
PRi
PRi
PRi
T1 (Trans-Tech)
1.3 mm
-
-
1.3 mm
PRi
PRi
PRi
PRi
PRi
PRi
PRi
T2 (Trans-Tech)
1.3 mm
1.3 mm
-
1.3 mm
1.3 mm
1.3 mm
PRi
PRi
PRi
PRi
PRi
PRi
T110 (Trans-Tech)
-
-
0.8 mm
0.8 mm
-
-
-
-
-
-
-
-
HS1 (HVLP)
0.8 mm
0.8 mm
0.8 mm
0.8 mm
0.8 mm
0.8 mm
1.2 mm
1.2 mm
1.2 mm
1.2 mm
0.8 mm
0.8 mm
SPRAY GUN SET UP SELECTOR: Gun Inlet Pressure 2.0 bar or as stated
Lackdatenblatt: Eingangsdruck: ca. 2.0 bar wie unten angegeben
PISTOLET ET TABLEAU DES REGLAGES: Pression à l’entrée du pistolet 2.0 bar ou comme indiqué
SCHEDA ALLESTIMENTO AEROGRAFO: pressione aria 2,0 bar o come indicato
CONFIGURACIONES DE PISTOLAS: Presión a la entrada de la pistola 2.0 bar o según lo indicado
2k Filler 540 wet-on-wet
-
1.3 mm
1.3 mm
1.3 mm
Clearcoats
TS1 (Trans-Tech)
Non Sanding Primer
Topcoat HS 420
-
-
1.3 mm
Primers
2k Single Stage
Basecoat SB
-
-
Fillers
Waterborne Basecoat Basecoat WB
Solventborne
Basecoat
2k HS Premium Clear 420
-
DeVilbiss Automotive Refinishing UK: +44 (0) 1202 571111 F: +33 (0) 4 75 75 27 80 D: +49 (0) 6074 403 251 Web: http://www.devilbisseu.com
2k HS Fast Clear 420
P1-1.4/1.6
1.856.3504
Aquamax Basecoat
1.500/1550 XXXX
Waterborne
Basecoat
Clearcoats
MaxiCar HS Basecoat
1.180/181.XXXX
Solventborne
Basecoat
1.360.0340
1.360.0350
HS Clear 0300 1.360.0300
HP Clear UHS 1.360.0950
HP Clear 1.360.0900
-
UHS Duralit Extra 1.150.
XXXX
2K Single Stage
TE10-1.2/1.3
TE20-1.2/1.3
-
TE10-1.2/1.3
TE20-1.2/1.3
HV30-1.2/1.3 @ 1.75 Bar
-
-
TE10-1.2/1.3
TE20-1.2/1.3
HV30-1.2/1.3 @ 1.75 Bar
-
H1-1.2/1.3
T1-1.2/1.3
H1-1.2/1.3
T1-1.2/1.3
-
TE10-1.2/1.3
TE20-1.2/1.3
-
-
-
BASE
-
-
-
CLEAR
TE10-1.3
-
-
-
BASE
T1-1.2/1.3
T2-1.2/1.3
-
HS1-0.8/1.0
TS1-0.8/1.0
HS1-0.8/1.0
TS1-0.8/1.0
HS1-0.8/1.0
TS1-0.8/1.0
HS1-0.8/1.0
TS1-0.8/1.0
T1-1.2/1.3
T2-1.2/1.3
-
HS1-0.8/1.0
TS1-0.8/1.0
-
HS1-0.8/1.0
TS1-0.8/1.0
SMART
T1-1.3/1.4
-
-
CLEAR
DeVilbiss Automotive Refinishing UK: +44 (0) 1202 571111 F: +33 (0) 4 75 75 27 80 D: +49 (0) 6074 403 251 Web: http://www.devilbisseu.com
-
-
-
P1-1.4
HP Wet on Wet Primer
1.841.9101/9104/9106
HP Multigrey Filler
1.814.8700/8800/8900
P1-1.6/1.8
P1-1.4
1.815.7050
HP Epoxy Primer
1.855.990
P1-1.4
P1-1.4
1K Plastiprimer
1.823.1500
CFE Primer 7050
P1-1.4
PRIMER
Ecophos Primer 6020
MATERIAL
Non Sanding
Primer
Fillers
Primers
CATEGORY
SPRAY GUN SET UP SELECTOR: Gun Inlet Pressure 2.0 bar or as stated
Lackdatenblatt: Eingangsdruck: ca. 2.0 bar wie unten angegeben
PISTOLET ET TABLEAU DES REGLAGES: Pression à l’entrée du pistolet 2.0 bar ou comme indiqué
SCHEDA ALLESTIMENTO AEROGRAFO: pressione aria 2,0 bar o come indicato
CONFIGURACIONES DE PISTOLAS: Presión a la entrada de la pistola 2.0 bar o según lo indicado
CATEGORY
Mipa 2K-HS-Klarlack CS85
Mipa 2K-HS-Klarlack CX1
Mipa 2K-HS-Klarlack CX3
Mipa 2K-HS-Klarlack CC6
Mipa 2K-HS-Klarlack CC4
Mipa 2K-HS-Klarlack
C420
Mipa WBC 2-SchichtWasserbasislack
Mipa BC 2-SchichtBasislack
Mipa PUR HS 2K-AcrylDecklack
Mipa OC 2K-HS-AcrylDecklack
MATERIAL
-
-
-
-
-
-
-
-
-
-
-
PRIMER
-
-
-
-
-
-
-
-
TE10 1,2-1,3mm
TE10 1,2-1,3mm
-
-
BASE
TE10 1,2-1,3mm
TE10 1,2-1,3mm
TE10 1,2-1,3mm
TE10 1,2-1,3mm
TE10 1,2-1,3mm
TE10 1,2-1,3mm
TE10 1,2-1,3mm
TE10 1,2-1,3mm
TE10 1,2-1,3mm
-
-
TE10 1,2-1,3mm
TE10 1,2-1,3mm
CLEAR
-
-
-
-
-
-
-
-
-
T110 1,2-1,3mm
T110 1,2-1,3mm
-
-
BASE
T2/T110 1,2-1,3mm
T2/T110 1,2-1,3mm
T2/T110 1,2-1,3mm
T2/T110 1,2-1,3mm
T2/T110 1,2-1,3mm
T2/T110 1,2-1,3mm
T2/T110 1,2-1,3mm
T2/T110 1,2-1,3mm
T2/T110 1,2-1,3mm
-
-
T2/T110 1,2-1,3mm
T2/T110 1,2-1,3mm
CLEAR
HS1/TS1 1,0-1,2mm
HS1/TS1 1,0-1,2mm
HS1/TS1 1,0-1,2mm
HS1/TS1 1,0-1,2mm
HS1/TS1 1,0-1,2mm
HS1/TS1 1,0-1,2mm
HS1/TS1 1,0-1,2mm
HS1/TS1 1,0-1,2mm
HS1/TS1 1,0-1,2mm
HS1/TS1 1,2mm
HS1/TS1 1,0-1,2mm
-
-
SMART
SPRAY GUN SET UP SELECTOR: Gun Inlet Pressure 2.0 bar or as stated
Lackdatenblatt: Eingangsdruck: ca. 2.0 bar wie unten angegeben
PISTOLET ET TABLEAU DES REGLAGES: Pression à l’entrée du pistolet 2.0 bar ou comme indiqué
SCHEDA ALLESTIMENTO AEROGRAFO: pressione aria 2,0 bar o come indicato
CONFIGURACIONES DE PISTOLAS: Presión a la entrada de la pistola 2.0 bar o según lo indicado
Topcoats
Mipa 2K-HS-Klarlack CS44
-
-
Clearcoats
Basecoats
Mipa 2K-HS-Klarlack C85
-
DeVilbiss Automotive Refinishing UK: +44 (0) 1202 571111 F: +33 (0) 4 75 75 27 80 D: +49 (0) 6074 403 251 Web: http://www.devilbisseu.com
Mipa 2K-MS-Klarlack C75
P1 1,6mm
-
Mipa 2K-EP-Grundierfiller
Mipa 1K-Kunststoffprimer
-
-
-
-
-
-
-
-
-
-
-
-
BASE
TE10 1,2mm
-
-
-
-
-
TE10 1,3mm
-
-
-
-
-
CLEAR
-
-
-
-
-
-
-
-
-
-
-
-
BASE
T2/T110 1,2mm
-
-
-
-
-
T2/T110 1,3mm
-
-
-
-
-
CLEAR
DeVilbiss Automotive Refinishing UK: +44 (0) 1202 571111 F: +33 (0) 4 75 75 27 80 D: +49 (0) 6074 403 251 Web: http://www.devilbisseu.com
P1 1,4mm
Mipa 2K-Plastic-Grundierfiller
P1 1,4mm
Mipa F31 2K-HS-Direktfiller
P1 1,6-1,8mm
Mipa F41 2K-HS-Filler
P1 1,6-1,8mm
Mipa 2K-Acryl-Grundierfiller
10:1
P1 1,6-1,8mm
P1 1,4-1,6mm
Mipa 2K-Primer AZ
Mipa 4+1 Acrylfiller HS
P1 1,4-1,6mm
Mipa Aktivprimer
P1 1,3mm
P1 1,4-1,6mm
Mipa 2K-Primer CF
Mipa 2K-HS-Fillprimer
P1 1,4-1,6mm
Mipa Rapidprimer / Rapidfiller
Primer/Filler
PRIMER
MATERIAL
CATEGORY
-
-
-
-
-
-
-
-
-
-
-
-
SMART
SPRAY GUN SET UP SELECTOR: Gun Inlet Pressure 2.0 bar or as stated
Lackdatenblatt: Eingangsdruck: ca. 2.0 bar wie unten angegeben
PISTOLET ET TABLEAU DES REGLAGES: Pression à l’entrée du pistolet 2.0 bar ou comme indiqué
SCHEDA ALLESTIMENTO AEROGRAFO: pressione aria 2,0 bar o come indicato
CONFIGURACIONES DE PISTOLAS: Presión a la entrada de la pistola 2.0 bar o según lo indicado
P1-1.6/1.8
P1-1.4
PRIMER
-
-
-
BASE
TE10-1.2/1.3
TE20-1.2/1.3
TE10-1.3
-
-
CLEAR
H1-1.2/1.3
T1-1.2/1.3
-
-
-
-
BASE
-
T1-1.2/1.3
T2-1.2/1.3
T1-1.3/1.4
-
-
CLEAR
HS1-0.8/1.0
TS1-0.8/1.0
HS1-0.8/1.0
TS1-0.8/1.0
HS1-0.8/1.0
TS1-0.8/1.0
-
HS1-0.8/1.0
TS1-0.8/1.0
SMART
SPRAY GUN SET UP SELECTOR: Gun Inlet Pressure 2.0 bar or as stated
Lackdatenblatt: Eingangsdruck: ca. 2.0 bar wie unten angegeben
PISTOLET ET TABLEAU DES REGLAGES: Pression à l’entrée du pistolet 2.0 bar ou comme indiqué
SCHEDA ALLESTIMENTO AEROGRAFO: pressione aria 2,0 bar o come indicato
CONFIGURACIONES DE PISTOLAS: Presión a la entrada de la pistola 2.0 bar o según lo indicado
P1-1.4
-
-
MATERIAL
P565-3030/3031 Fast HS
Wet on Wet Primer
-
TE10-1.2/1.3
TE20-1.2/1.3
HV30-1.2/1.3 @ 1.75 Bar
CATEGORY
Non Sanding
Primer
2K HS Plus P471- Single
Layer Solid Colour System
-
Fillers
P565-5601/05/07 HS
Plus Primer Filler
P565-888/889 Fast High
Build Surfacer/Filler
P572-2001/2004 Priming
Plastic Substrates
P565-9868 Chromate
Free Wash Etch Primer
P565-9850 Chromate
Free Etch Primer
2K Single Stage
2K P422-Low VOC
Basecoat
HS1-0.8/1.0
TS1-0.8/1.0
Primers
Solventborne
Basecoat
-
HS1-0.8/1.0
TS1-0.8/1.0
H1-1.2/1.3
T1-1.2/1.3
T1-1.2/1.3
T2-1.2/1.3
-
-
TE10-1.2/1.3
TE20-1.2/1.3
HV30-1.2/1.3 @ 1.75 Bar
TE10-1.2/1.3
TE20-1.2/1.3
-
-
Aquabase Plus
P190-6512 2K SR Ceramic
Clearcoat
P190-6659 2K HS Plus Express
Clearcoat
P190-6676 HS Plus Clearcoat
DeVilbiss Automotive Refinishing UK: +44 (0) 1202 571111 F: +33 (0) 4 75 75 27 80 D: +49 (0) 6074 403 251 Web: http://www.devilbisseu.com
-
Waterborne
Basecoat
Clearcoats
P190-6680 2K HS Clearcoat
P190-6690 2K HS Plus Clearcoat
P190-7000 2K HS Clearcoat
Protect 340
Protect 360 1:1
WASH PRIMER
EPOXY PRIMER
WET-ON-WET
CLEARCOATS
FILLERS
NON SANDING
PRIMER
EPOXY PRIMER
Polyester Spray Filler
POLYESTER
-
P1 - 1.6/2.0
(1.5 - 2.0 bar)
P1 - 1.6/2.0
(1.5 - 2.0 bar)
Protect 330
Protect 350
Novakryl 530 Mat
-
-
TE10 - 1.4
(2.0 - 2.5 bar)
TE20 - 1.2/1.4
TE10/TE20 - 1.2/1.4
-
-
-
-
-
-
-
-
-
-
TE10/TE20 - 1.2/1.3
(1.5 - 2.0 bar)
-
-
-
-
-
-
-
TE10 - 1.2/1.3
(1.5 - 2.0 bar)
-
-
BASE
-
CLEAR
-
-
-
-
-
-
-
-
-
-
-
-
-
CLEAR
DeVilbiss Automotive Refinishing UK: +44 (0) 1202 571111 F: +33 (0) 4 75 75 27 80 D: +49 (0) 6074 403 251 Web: http://www.devilbisseu.com
-
-
-
P1 - 1.8/2.0
(1.5 - 2.0 bar)
Protect 310
-
-
P1 - 1.6/1.8
(1.5 - 2.0 bar)
Protect 300
Novakryl
540/570/580/590
-
-
-
P1 - 1.6/1.8
Protect 360 4:1 + 50%
-
-
-
-
-
BASE
Protect 330
Wet-on-Wet
P1 - 1.8/2.0
P1 - 2.5
-
-
P1-2.5
PRIMER
Protect 360 4:1 + 25%
Protect 360 4:1 + 10%
MATERIAL
CATEGORY
-
-
-
-
-
-
-
-
-
-
-
-
-
SMART
SPRAY GUN SET UP SELECTOR: Gun Inlet Pressure 2.0 bar or as stated
Lackdatenblatt: Eingangsdruck: ca. 2.0 bar wie unten angegeben
PISTOLET ET TABLEAU DES REGLAGES: Pression à l’entrée du pistolet 2.0 bar ou comme indiqué
SCHEDA ALLESTIMENTO AEROGRAFO: pressione aria 2,0 bar o come indicato
CONFIGURACIONES DE PISTOLAS: Presión a la entrada de la pistola 2.0 bar o según lo indicado
Epoxy Primer Wet
on Wet
PF131 2K HS grey, white
& black
PE130 white & grey
PE130 white & grey
PW170
-
1.6 - 1.8 mm
-
1.6 - 1.8 mm
1.6 - 1.8 mm
P1 (Trans-Tech)
-
-
-
-
-
-
H1 (HVLP)
-
1.3 mm
-
-
-
-
-
T1 (Trans-Tech)
1.2 - 1.3 mm
1.3 mm
-
1.3 - 1.4 mm
-
1.3 - 1.4 mm
-
1.3 - 1.4 mm
T2 (Trans-Tech)
-
-
-
1.3 mm
-
-
-
-
-
T110 (Trans-Tech)
-
-
-
-
-
-
-
-
-
HS1 (HVLP)
-
-
-
-
-
-
-
-
-
SPRAY GUN SET UP SELECTOR: Gun Inlet Pressure 2.0 bar or as stated
Lackdatenblatt: Eingangsdruck: ca. 2.0 bar wie unten angegeben
PISTOLET ET TABLEAU DES REGLAGES: Pression à l’entrée du pistolet 2.0 bar ou comme indiqué
SCHEDA ALLESTIMENTO AEROGRAFO: pressione aria 2,0 bar o come indicato
CONFIGURACIONES DE PISTOLAS: Presión a la entrada de la pistola 2.0 bar o según lo indicado
HS Surfacer 2K
PF131 2K HS grey, white
& black
-
-
-
1.3 mm
TS1 (Trans-Tech)
HS Surfacer 2K
Wet on Wet
Octobase Eco
-
-
-
Wash Primer
Waterbase
Topcoat
C150 2K HS
-
-
Epoxy Primer
Clearcoat
C248 HS420 gr/lt
-
DeVilbiss Automotive Refinishing UK: +44 (0) 1202 571111 F: +33 (0) 4 75 75 27 80 D: +49 (0) 6074 403 251 Web: http://www.devilbisseu.com
Octocoat 2K HS 420 gr/lt
Solid Colour 2K LD
Deltron Basecoat
Envirobase High
Performance
Solventborne
Basecoat
Waterborne
Basecoat
Clearcoats
UHS Deltron Progress
2K Single Stage
D8141 UHS Clearcoat
D8138/D8171 UHS
Premium Clearcoat
D8135 UHS
Rapid Clearcoat
D8122 CeramiClear
D8113 Matt Clearcoat
D8105 CeramiClear
D8501/D8505/D8507
HS Wet on Wet Primer
D8018/D8019/D8024
Greymatic Primer
Non Sanding
Primer
Fillers
D8092 Universal Etch
Primer
Primers
D8010/D8015/D8017
Rapid Greymatic Primer
MATERIAL
CATEGORY
TE10-1.2/1.3
TE20-1.2/1.3
-
TE10-1.2/1.3
TE20-1.2/1.3
HV30-1.2/1.3 @ 1.75 Bar
-
-
TE10-1.2/1.3
TE20-1.2/1.3
HV30-1.2/1.3 @ 1.75 Bar
-
H1-1.2/1.3
T1-1.2/1.3
H1-1.2/1.3
T1-1.2/1.3
-
TE10-1.2/1.3
TE20-1.2/1.3
-
-
-
BASE
-
-
-
CLEAR
TE10-1.3
-
-
-
BASE
T1-1.2/1.3
T2-1.2/1.3
-
HS1-0.8/1.0
TS1-0.8/1.0
HS1-0.8/1.0
TS1-0.8/1.0
HS1-0.8/1.0
TS1-0.8/1.0
HS1-0.8/1.0
TS1-0.8/1.0
T1-1.2/1.3
T2-1.2/1.3
-
HS1-0.8/1.0
TS1-0.8/1.0
-
HS1-0.8/1.0
TS1-0.8/1.0
SMART
T1-1.3/1.4
-
-
CLEAR
DeVilbiss Automotive Refinishing UK: +44 (0) 1202 571111 F: +33 (0) 4 75 75 27 80 D: +49 (0) 6074 403 251 Web: http://www.devilbisseu.com
-
-
-
-
P1-1.4
P1-1.6/1.8
P1-1.4
PRIMER
SPRAY GUN SET UP SELECTOR: Gun Inlet Pressure 2.0 bar or as stated
Lackdatenblatt: Eingangsdruck: ca. 2.0 bar wie unten angegeben
PISTOLET ET TABLEAU DES REGLAGES: Pression à l’entrée du pistolet 2.0 bar ou comme indiqué
SCHEDA ALLESTIMENTO AEROGRAFO: pressione aria 2,0 bar o come indicato
CONFIGURACIONES DE PISTOLAS: Presión a la entrada de la pistola 2.0 bar o según lo indicado
Polyester
CATEGORY
MULTI FILLER CP
MULTI FILLER BLACK CP
STOP FILLER II
MATERIAL
P1-1.6/1.8 @ 2.0 Bar
P1-1.6/1.8 @ 2.0 Bar
P1-2.5 @ 2.0 Bar
PRIMER
-
-
-
-
BASE
-
-
-
CLEAR
-
-
-
-
BASE
H1-1.3/1.4 @ 2.0 Bar
T1-1.3/1.4 @ 2.2 Bar
T2-1.3/1.4 @ 2.2 Bar
T110-1.3/1.4 @ 2.0 Bar
-
-
-
CLEAR
-
-
-
-
SMART
SPRAY GUN SET UP SELECTOR: Gun Inlet Pressure 2.0 bar or as stated
Lackdatenblatt: Eingangsdruck: ca. 2.0 bar wie unten angegeben
PISTOLET ET TABLEAU DES REGLAGES: Pression à l’entrée du pistolet 2.0 bar ou comme indiqué
SCHEDA ALLESTIMENTO AEROGRAFO: pressione aria 2,0 bar o come indicato
CONFIGURACIONES DE PISTOLAS: Presión a la entrada de la pistola 2.0 bar o según lo indicado
Fillers
HYDROFILLER II
P1-1.4 @2.0 Bar
TE10-1.3/1.4 @ 2.0 Bar
TE20-1.3/1.4 @ 2.0 Bar
HV30-14 @ 1.75 Bar
HS1-1.0/1.2 @ 1.5-2.0 Bar
TS1-1.0/1.2 @ 1.5-2.0 Bar
EXTRASEALER WHITE/
BLACK
-
H1-1.3 @ 2.0 Bar
T1-1.3/1.4 @ 2.2 Bar
T2-1.3/1.4 @ 2.2 Bar
T110-1.3/1.4 @ 2.0 Bar
HS1-1.0/1.2 @ 1.5-2.0 Bar
TS1-1.0/1.2 @ 1.5-2.0 Bar
DIAMONT
-
Solventborne
Basecoat
Non Sanding
Primer
-
-
HS1-1.0/1.2 @ 1.5-2.0 Bar
TS1-1.0/1.2 @ 1.5-2.0 Bar
-
TE10-1.3/1.4 @ 2.0 Bar
TE20-1.3/1.4 @ 2.0 Bar
HV30-14 @ 1.75 Bar
H1-13/1.4 @ 2.0 Bar
T2-1.3/1.4 @ 2.0 Bar
-
TE20-1.4 @ 2.0 Bar
HV30-14 @ 1.75 Bar
ONYX HD
-
Waterborne
Basecoat
UNO HD / UNO HD 420
-
H1-14 @ 2.0 Bar
T2-1.4 @ 2.0 Bar
HS1-1.0/1.2 @ 1.5-2.0 Bar
TS1-1.0/1.2 @ 1.5-2.0 Bar
-
-
Clearcoats
2K Single Stage
TE20-1.4 @ 2.0 Bar
HV30-14 @ 1.75 Bar
-
-
H1-1.3 @ 2.0 Bar
T1-1.3/1.4 @ 2.2 Bar
T2-1.3/1.4 @ 2.2 Bar
T110-1.3/1.4 @ 2.0 Bar
DeVilbiss Automotive Refinishing UK: +44 (0) 1202 571111 F: +33 (0) 4 75 75 27 80 D: +49 (0) 6074 403 251 Web: http://www.devilbisseu.com
TE10-1.3/1.4 @ 2.0 Bar
TE20-1.3/1.4 @ 2.0 Bar
HV30-14 @ 1.75 Bar
CHRONOTOP, DIAMONT MS,
STARTOP HS,
CRYSTALCLEAR CP,
CHRONOLUX CP,
SUPREMELUX CP
CLEAR LOW V.O.C.
2K SINGLE STAGE
CLEAR
KRONOX 3100 UHS
KRONOX 410 UHS/410
EXPRESS
KRONOX HS 420
DISOLAC + 980
DISOLAC + 990
DISOLAC + 992
DISOTRANS Low V.O.C.
VT141 EXPRESS
SUPERIOR 150 HS
PREMIUM 250 HS
ELITE 350 HS
DICROM
SOLVENTBORNE
BASECOAT
-
-
TE10-1,3@2.0 bar
HV30-1,3@1.7 bar
TE10-1,3@2.0 bar
HV30-1,3@1.7 bar
TE10-1,3/1,4@2.0 bar
TE20-1,3/1,4@2.0 bar
-
-
-
-
BASE
TE10-1,3/1,4@2.2 bar
TE20-1,3/1,4@2.2 bar
TE10-1,3/1,4@1.7 bar
TE20-1,3/1,4@1.7 bar
TE10-1,3/1,4@2.2 bar
TE20-1,3/1,4@2.2 bar
TE10-1,3/1,4@2.0 bar
TE20-1,3/1,4@2.0 bar
TE10-1,3/1,4@2.2 bar
TE20-1,3/1,4@2.2 bar
CLEAR
-
-
T1-1,3@2.0 bar
H1-1,3@1.7 bar
T1-1,3@2.0 bar
H1-1,3@1.7 bar
T1-1,3/1,4@2.0 bar
-
-
-
-
BASE
T1-1,3/1,4@2.2 bar
T2-1,3/1,4@2.2 bar
T1-1,3/1,4@1.7 bar
T2-1,3/1,4@1.7 bar
T1-1,3/1,4@2.2 bar
T2-1,3/1,4@2.2 bar
T1-1,3/1,4@2.0 bar
T2-1,3/1,4@2.0 bar
T1-1,3/1,4@2.2 bar
T2-1,3/1,4@2.2 bar
CLEAR
DeVilbiss Automotive Refinishing UK: +44 (0) 1202 571111 F: +33 (0) 4 75 75 27 80 D: +49 (0) 6074 403 251 Web: http://www.devilbisseu.com
-
-
P1-1,4@2.0 bar
HYDRAX water base
OPABASE ACQUA
P1-1,4@2.0 bar
P1-1,8@2.0 bar
P1-1,4/1,6@2.0 bar
P1-1,6/1,8@2.0 bar
P1-1,6/1,8@2.0 bar
P1-1,6/1,8@2.0 bar
P1-1,4@2.0 bar
P1-2,5@2.0 bar
PRIMER
VERSIS w/w
WATERBORNE
BASECOAT
PRIMER
SURVINIL
WASH PRIMER
MEGAX High build
MEGAX Surfacer
MULTYFILLER PLUS
MULTYFILLER EXPRESS
VERSIS
A80 Sprayable polyester
MATERIAL
POLYESTER
CATEGORY
-
TS1-1.0/1,2@1.5-1.7 bar
TS1-1.0/1,2@1.5-2.0 bar
HS1-1.0/1,2@1.5-2.0 bar
TS1-1.0/1,2@1.5-2.0 bar
HS1-1.0/1,2@1.5-2.0 bar
TS1-1.0/1,2@1.5-2.0 bar
HS1-1.0/1,2@1.5-2.0 bar
TS1-1.0/1,2@1.5-2.0 bar
-
HS1-1.0/1,2@1.5-2.0 bar
TS1-1.0/1,2@1.5-2.0 bar
-
SMART
SPRAY GUN SET UP SELECTOR: Gun Inlet Pressure 2.0 bar or as stated
Lackdatenblatt: Eingangsdruck: ca. 2.0 bar wie unten angegeben
PISTOLET ET TABLEAU DES REGLAGES: Pression à l’entrée du pistolet 2.0 bar ou comme indiqué
SCHEDA ALLESTIMENTO AEROGRAFO: pressione aria 2,0 bar o come indicato
CONFIGURACIONES DE PISTOLAS: Presión a la entrada de la pistola 2.0 bar o según lo indicado
Non Sanding
Primer
Fillers
Polyester
CATEGORY
UNO HD / UNO HD CP
EXTRASEALER WHITE/
BLACK
PERFECTFILLER
GREY / WHITE / BLACK
HYDROFILLER II
MULTI FILLER CP
MULTI FILLER BLACK CP
STOP FILLER II
MATERIAL
-
P1-1.4 @2.0 Bar
P1-1.6/1.8 @ 2.0 Bar
P1-1.6/1.8 @ 2.0 Bar
P1-1.6/1.8 @ 2.0 Bar
P1-2.5 @ 2.0 Bar
PRIMER
-
-
-
-
-
-
BASE
TE10-1.3/1.4 @ 2.0 Bar
TE20-1.3/1.4 @ 2.0 Bar
HV30-14 @ 1.75 Bar
-
-
-
-
CLEAR
-
-
-
-
-
BASE
-
-
-
-
CLEAR
-
-
-
-
SMART
1.6 - 1.8 @ 2.0 BAR
1.6 - 1.8 @ 2.0 BAR
-
-
GPi
SPRAY GUN SET UP SELECTOR: Gun Inlet Pressure 2.0 bar or as stated
Lackdatenblatt: Eingangsdruck: ca. 2.0 bar wie unten angegeben
PISTOLET ET TABLEAU DES REGLAGES: Pression à l’entrée du pistolet 2.0 bar ou comme indiqué
SCHEDA ALLESTIMENTO AEROGRAFO: pressione aria 2,0 bar o come indicato
CONFIGURACIONES DE PISTOLAS: Presión a la entrada de la pistola 2.0 bar o según lo indicado
2K Single Stage
TE20-1.4 @ 2.0 Bar
HV30-14 @ 1.75 Bar
-
H1-13/1.4 @ 2.0 Bar
T2-1.3/1.4 @ 2.0 Bar
-
-
-
HS1-1.0/1.2 @ 1.5-2.0 Bar
TS1-1.0/1.2 @ 1.5-2.0 Bar
HS1-1.0/1.2 @ 1.5-2.0
Bar TS1-1.0/1.2 @ 1.52.0 Bar
HS1-1.0/1.2 @ 1.5-2.0
Bar TS1-1.0/1.2 @ 1.52.0 Bar
-
-
-
-
-
H1-1.3/1.4 @ 2.0 Bar
T1-1.3/1.4 @ 2.2 Bar
T2-1.3/1.4 @ 2.2 Bar
T110-1.3/1.4 @ 2.0 Bar
H1-1.3 @ 2.0 Bar
T1-1.3/1.4 @ 2.2 Bar
T2-1.3/1.4 @ 2.2 Bar
T110-1.3/1.4 @ 2.0 Bar
TE10-1.3/1.4 @ 2.0 Bar
TE20-1.4 @ 2.0 Bar
HV30-14 @ 1.75 Bar
DIAMONT
H1-14 @ 2.0 Bar
T2-1.4 @ 2.0 Bar
-
-
Solventborne
Basecoat
-
HS1-1.0/1.2 @ 1.5-2.0 Bar
TS1-1.0/1.2 @ 1.5-2.0 Bar
TE20-1.4 @ 2.0 Bar
HV30-14 @ 1.75 Bar
ONYX HD
-
-
Waterborne
Basecoat
-
-
Clearcoats
H1-1.3 @ 2.0 Bar
T1-1.3/1.4 @ 2.2 Bar
T2-1.3/1.4 @ 2.2 Bar
T110-1.3/1.4 @ 2.0 Bar
DeVilbiss Automotive Refinishing UK: +44 (0) 1202 571111 F: +33 (0) 4 75 75 27 80 D: +49 (0) 6074 403 251 Web: http://www.devilbisseu.com
TE10-1.3/1.4 @ 2.0 Bar
TE20-1.3/1.4 @ 2.0 Bar
HV30-14 @ 1.75 Bar
CHRONOTOP, DIAMONT MS,
STARTOP HS,
CRYSTALCLEAR CP,
CHRONOLUX CP,
SUPREMELUX CP
-
Colorbuild Plus (Non
sanding)
Autocryl Plus LV MM
Autowave MM 2.0
Non Sanding
Primer
2K Single Stage
Clearcoats
Waterborne
Basecoat
-
Colorbuild Plus (Sanding)
Primer Surfacer EP II
Fillers
-
Autoclear LV Exclusive
Autoclear LV Superior
Autoclear Mix & Mat
Autoclear UV
Autoclear WB
-
TE10-1.3
HV30-1.3 @ 1.75 Bar
TE10-1.3/1.4
-
-
-
-
BASE
TE10-1.3 /1.4
TE20-1.3
-
-
H1-1.3
T110-1.3
T110-1.3/1.4
-
TE10-1.3
TE20-1.3
-
-
-
-
BASE
TE10-1.3/1.4
-
-
CLEAR
T110-1.3
T2-1.3
-
HS1-0.8/1.0
TS1-0.8/1.0
HS1-0.8/1.0
TS1-0.8/1.0
HS1-0.8/1.0
TS1-0.8/1.0
HS1-0.8/1.0
TS1-0.8/1.0
T110-1.3
T2-1.3
-
HS1-0.8/1.0
TS1-0.8/1.0
-
HS1-0.8/1.0
TS1-0.8/1.0
SMART
TE10-1.3/1.4
-
-
CLEAR
DeVilbiss Automotive Refinishing UK: +44 (0) 1202 571111 F: +33 (0) 4 75 75 27 80 D: +49 (0) 6074 403 251 Web: http://www.devilbisseu.com
-
Autowave MM
P1-1.4
P1-1.6/2.0
P1-1.4
Washprimer 1K CF
2K Plastic Primer
Primers
PRIMER
MATERIAL
CATEGORY
SPRAY GUN SET UP SELECTOR: Gun Inlet Pressure 2.0 bar or as stated
Lackdatenblatt: Eingangsdruck: ca. 2.0 bar wie unten angegeben
PISTOLET ET TABLEAU DES REGLAGES: Pression à l’entrée du pistolet 2.0 bar ou comme indiqué
SCHEDA ALLESTIMENTO AEROGRAFO: pressione aria 2,0 bar o come indicato
CONFIGURACIONES DE PISTOLAS: Presión a la entrada de la pistola 2.0 bar o según lo indicado
CATEGORY
Primers
Fillers
2k Single Stage
Solventborne
Basecoat
Waterborne Basecoat
Clearcoats
WB Filler 1K grey
HS Filler Qick Fill 3900
HS Filler - Primer 7900
2K Polyester Spray Filler
8080
-
-
-
-
-
1.4
1,4 - 1,8
1,6 - 2,5
2,0 - 2,5
-
-
1,4 - 1,6
PRIMER
-
-
-
-
-
-
-
-
-
-
-
-
-
BASE
1,2 - 1,3
1,3 - 1,4
1,3 - 1,4
-
-
-
1,3 -1,4
1,2 - 1,3
1,3 - 1,4
1,3 - 1,4
-
-
-
1,3 - 1,4
CLEAR
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
BASE
1,3 - 1,4
1,2 - 1,3
1,2 - 1,3
1,3 - 1,4
1,3 - 1,4
-
-
-
1,3 - 1,4
1,2 - 1,3
1,3 - 1,4
1,3 - 1,4
-
-
-
1,3 - 1,4
CLEAR
-
-
-
-
-
-
-
-
-
1.0
-
-
-
-
-
-
SMART
SPRAY GUN SET UP SELECTOR: Gun Inlet Pressure 2.0 bar or as stated
Lackdatenblatt: Eingangsdruck: ca. 2.0 bar wie unten angegeben
PISTOLET ET TABLEAU DES REGLAGES: Pression à l’entrée du pistolet 2.0 bar ou comme indiqué
SCHEDA ALLESTIMENTO AEROGRAFO: pressione aria 2,0 bar o come indicato
CONFIGURACIONES DE PISTOLAS: Presión a la entrada de la pistola 2.0 bar o según lo indicado
S.Mix 84
-
-
1,2 - 1,3
-
MATERIAL
Clear Coat Maxx 2
-
-
1,3 - 1,4
Clear Coat UHS Maxx 8
Express
Clear Coat UHS Maxx 8
Premium
Epoxy Primer 2110
Clear Coat Maxx 4
-
-
DeVilbiss Automotive Refinishing UK: +44 (0) 1202 571111 F: +33 (0) 4 75 75 27 80 D: +49 (0) 6074 403 251 Web: http://www.devilbisseu.com
-
Clear Coat Maxx Matt
-
Under 325 Wet-on-Wet
-
P1 - 1.6/1.8
(1.5 - 2.0 bar)
P1 - 1.6/1.8
(1.5 - 2.0 bar)
Under 355
Under 365
-
Spectral Wave
Klar 505/555
WATERBORNE
BASECOAT
-
Klar 575
Klar 535 Mat
-
-
-
-
HV30 - 1.3
(1.5 - 2.0 bar)
HV30 - 1.3
(1.5 - 2.0 bar)
-
TE10/TE20 - 1.2/1.4
(1.5 - 2.0 Bar)
TE20 - 1.2/1.4
(1.5 - 2.0 Bar)
-
TE10/TE20 - 1.2/1.3
(1.5 - 2.0 Bar)
TE10/TE20 - 1.2/1.3
(1.5 - 2.0 Bar)
H1 - 1.3
(1.5 - 2.0 bar)
H1 - 1.3
(1.5 - 2.0 bar)
-
-
-
-
-
TE10/TE20 - 1.2/1.4
-
-
-
-
TE10/TE20 - 1.3
(1.5 - 2.0 Bar)
-
-
-
TE20 - 1.3
(1.5 - 2.0 Bar)
TE10/TE20 - 1.2/1.3
(1.5 - 2.0 Bar)
-
-
BASE
TE10 - 1.2
(1.5 Bar)
TE10 - 1.2/1.3
CLEAR
T2 - 1.2/1.4
T110/T1/T2 - 1.2/1.4
T110/T1/T2 - 1.2/1.3
T110/T1/T2 - 1.2/1.3
-
-
T110/T1/T2 - 1.2/1.4
-
-
-
T1/T2 - 1.3
(1.5 - 2.0 Bar)
T1/T2 - 1.2/1.3
(1.5 - 2.0 Bar)
T2 - 1.3
(1.5 - 2.0 Bar)
TS1 - 1.0
(1.5 - 2.0 bar)
TS1 - 1.0
(1.5 - 2.0 bar)
TS1 - 1.0
(1.5 - 2.0 bar)
HS1 - 0.8
(1.5 - 2.0 bar)
HS1 - 0.8
(1.5 - 2.0 bar)
HS1 - 0.8
(1.5 - 2.0 bar)
-
-
-
-
-
-
-
-
-
T1 - 1.2/1.3
(1.5 - 2.0 Bar)
T1 - 1.2
(1.5 - 2.0 Bar)
SMART
CLEAR
DeVilbiss Automotive Refinishing UK: +44 (0) 1202 571111 F: +33 (0) 4 75 75 27 80 D: +49 (0) 6074 403 251 Web: http://www.devilbisseu.com
-
Klar 565
CLEARCOATS
-
Spectral Base
SOLVENTBORNE
BASECOAT
-
Spectral 2K
-
-
P1 - 1.6/1.8
(1.5 - 2.0 bar)
-
-
-
Under 365 Wet-on-Wet
Under 335
-
-
-
-
-
-
BASE
Under 335 Wet-on-Wet
2K SINGLE STAGE
FILLERS
NON SANDING
PRIMER
-
Under 385
EPOXY PRIMER
WET-ON-WET
-
Under 345
WASH PRIMER
PRIMER
MATERIAL
CATEGORY
SPRAY GUN SET UP SELECTOR: Gun Inlet Pressure 2.0 bar or as stated
Lackdatenblatt: Eingangsdruck: ca. 2.0 bar wie unten angegeben
PISTOLET ET TABLEAU DES REGLAGES: Pression à l’entrée du pistolet 2.0 bar ou comme indiqué
SCHEDA ALLESTIMENTO AEROGRAFO: pressione aria 2,0 bar o come indicato
CONFIGURACIONES DE PISTOLAS: Presión a la entrada de la pistola 2.0 bar o según lo indicado
Primers
CATEGORY
Permasolid® HS Clear
Coat 8034
Permahyd® Hi-TEC
Basecoat 480
Permahyd® Basecoat
Series 280/285
Permacron® Base Coat
Series 293/295
Permasolid® Automotive
Top Coat Series 275
Permacron® Elastic
Primer Surfacer 3300
Priomat® 1K Wash Primer
4085
Priomat® 1K Wash Primer
4075
MATERIAL
-
-
-
-
-
-
P1-1.4
P1-1.6/1.8
P1-1.6/1.8
P1-1.4
P1-1.4
P1-1.4
PRIMER
-
-
-
TE20-1.2/1.3
TE20-1.2/1.3
TE20-1.2/1.3
TE20-1.2/1.3
TE10-13
-
-
-
-
-
BASE
TE10-1.3
TE10-1.3
TE10-1.3
TE10-1.3
-
-
-
TE20-1.2/1.3
TE10-13
-
-
-
-
-
CLEAR
-
-
-
-
-
T2-1.2/1.3
T2-1.2/1.3
T2-1.2/1.3
T2-1.2/1.3
T1-13
-
-
-
-
-
BASE
T2-1.3
T2-1.3
T2-1.3
T2-1.3
T2-1.3
-
-
-
T2-1.2/1.3
T1-13
-
-
-
-
-
CLEAR
HS1/TS1-0.8/1.0
HS1/TS1-0.8/1.0
HS1/TS1-0.8/1.0
HS1/TS1-0.8/1.0
HS1/TS1-0.8/1.0
HS1/TS1-0.8/1.0
HS1/TS1-0.8/1.0
HS1/TS1-0.8/1.0
HS1/TS1-0.8/1.0
TS1-0.8
TS1-1.0/1.2
TS1-1.0/1.2
TS1-0.8
TS1-0.8
TS1-0.8
SMART
SPRAY GUN SET UP SELECTOR: Gun Inlet Pressure 2.0 bar or as stated
Lackdatenblatt: Eingangsdruck: ca. 2.0 bar wie unten angegeben
PISTOLET ET TABLEAU DES REGLAGES: Pression à l’entrée du pistolet 2.0 bar ou comme indiqué
SCHEDA ALLESTIMENTO AEROGRAFO: pressione aria 2,0 bar o come indicato
CONFIGURACIONES DE PISTOLAS: Presión a la entrada de la pistola 2.0 bar o según lo indicado
2k Single Stage
Permasolid® HS Clear
Coat 8055
-
-
TE10-1.3
Clearcoats
Non Sanding
Primer
Fillers
Solventborne
Basecoat
Permasolid® HS Diamond
Clear Coat 8450
-
-
Permasolid® HS Express
Surfacer 5250
Permasolid® HS
Performance Surfacer
5320
Permasolid® HS Vario
Primer Surfacer 5340
Waterborne
Basecoat
Permasolid® HS Optimum
Plus Clear 8650
-
DeVilbiss Automotive Refinishing UK: +44 (0) 1202 571111 F: +33 (0) 4 75 75 27 80 D: +49 (0) 6074 403 251 Web: http://www.devilbisseu.com
Permasolid® HS Speed
Clear Coat 8800
-
Standohyd® Basecoat
Standoblue® Basecoat
Standocryl® VOC Express
Clear K9530
Standocryl® VOC 2K
Clear K9550
Standocryl® VOC Xtra
Clear K9560
Standocryl® VOC
Platinum Clear K9570
Standocryl® VOC Xtreme
Clear K9580
Waterborne
Basecoat
CLEARCOATS
-
Standox Basecoat
Solventborne
Basecoat
-
-
-
-
-
TE20-1.2/1.3
TE20-1.2/1.3
TE20-1.2/1.3
TE20-1.2/1.3
TE10-13
-
-
-
-
-
BASE
TE10-1.3
TE10-1.3
TE10-1.3
TE10-1.3
TE10-1.3
-
-
-
TE20-1.2/1.3
TE10-13
-
-
-
-
-
CLEAR
-
-
-
-
-
T2-1.2/1.3
T2-1.2/1.3
T2-1.2/1.3
T2-1.2/1.3
T1-13
-
-
-
-
-
BASE
T2-1.3
T2-1.3
T2-1.3
T2-1.3
T2-1.3
-
-
-
T2-1.2/1.3
T1-13
-
-
-
-
-
CLEAR
DeVilbiss Automotive Refinishing UK: +44 (0) 1202 571111 F: +33 (0) 4 75 75 27 80 D: +49 (0) 6074 403 251 Web: http://www.devilbisseu.com
-
-
Standocryl® VOC Topcoat
2k Single Stage
P1-1.4
VOC Non Stop Primer
Surfacer U7580
P1-1.6/1.8
VOC Pro Filler
NON SANDING
PRIMER
P1-1.6/1.8
P1-1.4
Standoflex® 2KPrimer
Surfacer U3020
VOC XTRA Filler U7560
P1-1.4
1K Primer Filler
Fillers
P1-1.4
Etching Adhesion Primer
Primers
PRIMER
MATERIAL
CATEGORY
HS1/TS1-0.8/1.0
HS1/TS1-0.8/1.0
HS1/TS1-0.8/1.0
HS1/TS1-0.8/1.0
HS1/TS1-0.8/1.0
HS1/TS1-0.8/1.0
HS1/TS1-0.8/1.0
HS1/TS1-0.8/1.0
HS1/TS1-0.8/1.0
TS1-0.8
TS1-1.0/1.2
TS1-1.0/1.2
TS1-0.8
TS1-0.8
TS1-0.8
SMART
SPRAY GUN SET UP SELECTOR: Gun Inlet Pressure 2.0 bar or as stated
Lackdatenblatt: Eingangsdruck: ca. 2.0 bar wie unten angegeben
PISTOLET ET TABLEAU DES REGLAGES: Pression à l’entrée du pistolet 2.0 bar ou comme indiqué
SCHEDA ALLESTIMENTO AEROGRAFO: pressione aria 2,0 bar o come indicato
CONFIGURACIONES DE PISTOLAS: Presión a la entrada de la pistola 2.0 bar o según lo indicado
Conditions of Sale
accompany the equipment purchase order.
FINISHING BRANDS UK LIMITED (“FBUK”)
4.2. Before signing the prints the Buyer shall check
equipment size, location of building, and all
interferences as shown on the drawings, data
sheets etc and clearances and note clearly and
comprehensively any changes or interferences on the
prints.
4.3. If Goods are to be made or any process is to be
applied in accordance with a specification, drawing
or design submitted by the Buyer, the Buyer shall
indemnify FBUK against all loss, damages, costs and
expenses awarded against or incurred by FBUK in
connection with or paid or agreed to be paid by FBUK
in settlement of any claim for infringement of any third
party rights which results from FBUK’s use of such
material.
4.4. If any claim is made against the Buyer that the Goods
supplied or their proper use infringe the intellectual
property rights of any other person, FBUK shall
indemnify the Buyer against all damages, costs and
expenses awarded against the Buyer in connection with
the claim provided that:
1. INTERPRETATION
1.1 In these Conditions:
Business Day:
a day (other than a Saturday, Sunday or public
holiday) when banks in London are open for
business.
Buyer: Is the person who accepts FBUK’s quotation or
whose order is accepted by FBUK.
Conditions: Are these conditions of sale and (unless the
context otherwise requires) includes any
special terms on the face of FBUK’s quotation
or acceptance of the Buyer’s order.
Contract: Is the contract for the purchase and sale of the
Goods and/or supply of services.
Goods:
Are the goods which FBUK is to supply.
2. BASIS OF THE SALE
2.1.
Subject to FBUK’s quotation, all Goods are sold and services
supplied subject to these Conditions to the exclusion of any
other terms and conditions.
2.2. No variation to these Conditions shall be binding unless agreed
in writing by a general manager of FBUK.
2.3.
FBUK’s employees or agents are not authorised to make any
representations unless confirmed by FBUK in writing. The
Buyer acknowledges that it does not rely on, and irrevocably
waives any claim it may have for damages for or the right to
rescind the Contract for any such representations which are not
so confirmed (unless such representations were fraudulently
made).
2.4.
2.5. Any advice or recommendation given by FBUK or its employees
or agents to the Buyer or its employees or agents which is not
confirmed in writing by FBUK is followed or acted upon entirely
at the Buyer’s own risk and FBUK shall not be liable for any such
advice or recommendation which is not so confirmed.
Any typographical, clerical or other error or omission in any
sales literature, quotation, price list, acceptance of offer, invoice
or other document or information issued by FBUK shall be
subject to correction without any liability on the part of FBUK.
3. ORDERS AND SPECIFICATIONS
3.1. Quotations are valid for 60 days only. No order submitted by
the Buyer shall be deemed to be accepted by FBUK unless and
until confirmed in writing by FBUK.
3.2. The Buyer is responsible for ensuring the accuracy of the terms
of any order and for giving FBUK any necessary information
within a sufficient time to enable FBUK to perform the Contract.
3.3. The quantity and description of and any specification for the
Goods or services shall be those set out in FBUK’s quotation
(if accepted by the Buyer) or FBUK’s acceptance of the Buyer’s
order.
3.4. FBUK reserves the right to make any changes in the
specification of the Goods (including materials and
components) which are required to conform with any
applicable law or, which do not materially affect their quality or
performance.
3.5. An order once accepted by FBUK may only be cancelled with
its written agreement and the Buyer shall indemnify FBUK in full
against all loss (including loss of profit), costs (including labour
and materials) and damages incurred by FBUK.
4. DRAWINGS AND SPECIFICATIONS
4.1. 96
Any specifications or drawings supplied remain FBUK’s
sole property and are subject to recall at any time
before FBUK’s quotation is accepted. Any drawings
supplied are not to be used for construction purposes.
Where FBUK’s quotation includes a drawing reference,
copy of any approved prints or equipment data
sheets, these must be signed by the Buyer and must
4.4.1. FBUK is given full control of any proceedings or
negotiations in connection with any such claim;
4.4.2.
the Buyer shall pay to FBUK all damages and costs (if
any) awarded in favour of the Buyer which are payable
by, or agreed with the consent of the Buyer (which
consent shall not be unreasonably withheld) to be paid
by, any other party in respect of any such claim; and
4.4.3. without prejudice to any duty of the Buyer at common
law, FBUK may require the Buyer to take such steps as
FBUK may reasonably require to mitigate or reduce any
such loss, damages, costs or expenses for which FBUK
is liable to indemnify the Buyer under this condition.
5. PREPARATION OF SITE
5.1. The Buyer shall obtain all necessary licences, permits and
permissions.
5.2. The Buyer shall clear the site for installation and make it ready
for the reception of the Goods. The Buyer shall keep the site
free from water, debris and obstructions, and make required
alterations to buildings and other equipment if required for the
proper clearance and support of the Goods.
5.3. The Buyer shall ensure that FBUK shall not be delayed by the
operations of others (including the Buyer) or the Buyer’s failure
to provide the conditions and facilities required. If such delays
cause extra visits by FBUK, these will be charged in addition.
5.4. The Buyer shall, at its own risk, unload the Goods and store
them close to the point of erection, provide safe and convenient
storage room for tools and materials, provide adequate work
room for FBUK personnel, give proper care to and provide
insurance against loss by fire and theft for all materials and
equipment prior to, during and after installation.
6. INSTALLATION LIABILITY
6.1. The Buyer shall provide the necessary foundations required,
carry out cutting away and making good, and grouting in
foundation bolts etc, and will provide a level concrete floor
for the plant of adequate strength. The Buyer shall be entirely
responsible for the exact siting of the Goods to meet the
Buyer’s requirements.
6.2. All gas, water, electrical and compressed air services (including
interconnecting wiring) shall be provided by the Buyer. All
building work such as cutting holes etc for stacks to be
undertaken by the Buyer.
6.3. If FBUK undertakes any of the work detailed in the previous
paragraphs to complete installation, such work shall be
charged in addition and FBUK shall not be responsible for any
consequential damage.
7. PLANT ACCEPTANCE/TAKING OVER
7.1. The Goods shall be deemed to have been accepted at the
earlier of:
Catalogue 2015
7.1.1.
When installation has been completed and the Goods
have passed or are deemed to have passed all tests
provided for in FBUK’s proposal; or
7.1.2. One calendar month after the Goods shall have been
put into use.
7.2. the Buyer that the Goods are available for collection or when
the Goods leave FBUK’s premises, whichever is the earlier.
11.2. The time of acceptance shall not be delayed because of
additions, minor omissions or defects which do not materially
affect the use of the Goods or if the Buyer is preventing FBUK
from completing the Contract.
11.2.1. hold the Goods as FBUK’s fiduciary agent and bailee,
and shall keep them separate from all other goods and
properly stored, protected and insured and identified
as FBUK’s property but may resell or use the Goods in
the ordinary course of its business;
8. PRICE
8.1. The price shall be FBUK’s quoted price (or if a quoted price is
no longer valid), the price stated in FBUK’s acknowledgement of
order. Prices are ex works.
8.2. FBUK may, by giving notice to the Buyer at any time before
delivery, increase the price to reflect any increase in the cost to
FBUK which is due to any factor beyond the control of FBUK.
8.3. Any applicable value added tax or other taxes or duties are
payable by the Buyer in addition.
8.4. Goods for export will be packed in good quality export cases
at the Buyer’s cost. Any special packing requirements of the
Buyer will attract an additional charge. Packing for parcel post
or air freight will be in an appropriately economic manner using
cartons and/or parcels.
11.2.2. (provided the Goods are still in existence and have
not been resold), deliver up the Goods to FBUK on
demand
11.2.3. and, if the Buyer fails to do so immediately, FBUK may
enter any premises of the Buyer or any third party
where the Goods are stored and repossess the Goods.
12. WARRANTIES AND LIABILITIES
12.1. FBUK warrants that it holds unencumbered title to the Goods
and will perform services with reasonable skill and care.
12.2. Subject to condition 12.3, FBUK warrants that the Goods will
correspond with their specification at the time of delivery and
will be free from defects in material and workmanship for 12
months from delivery.
12.3. The above warranty does not apply to any defect:
9. TERMS OF PAYMENT
9.1. Payment shall be made in accordance with FBUK’s quotation.
9.2. FBUK may recover the price, notwithstanding that delivery may
not have taken place and the property in the Goods has not
passed. The time of payment shall be of the essence of the
Contract.
9.3. 12.3.1. arising from any drawing, design or specification
supplied by the Buyer;
12.3.2. arising from fair wear and tear, improper use, storage
or installation or maintenance, failure to follow FBUK’s
instructions (whether oral or in writing), or alteration or
repair of the Goods without FBUK’s approval;
FBUK may charge the Buyer interest (both before and after any
judgement) on the amount unpaid, at the rate of 4 per cent per
annum above the base rate from time to time of HSBC Bank plc
until payment in full is made.
12.3.3. which is not immediately notified in writing to FBUK;
10. DELIVERY
10.1. 10.2. FBUK shall replace or repair free of charge the Goods (or the
part in question) returned to FBUK’s factory carriage paid which
do not meet the warranty in condition 12.2 or, at FBUK’s sole
discretion, refund to the Buyer the price of the Goods (or a
proportionate part of the price) but FBUK shall have no further
liability to the Buyer. The warranty on replacements or repairs
shall be to the end of the original warranty period. Repairs and
replacements will be delivered free within the UK and to the
nearest port or airport c.i.f. outside the UK.
12.5. 10.4.1. store the Goods until actual delivery and charge the
Buyer for the costs (including insurance) of storage; or
Subject as expressly provided in these Conditions, all
warranties, conditions, representations or other terms implied
by statute or common law are excluded to the fullest extent
permitted by law.
12.6. 10.4.2. sell the Goods at the best price readily obtainable and
(after deducting all storage, selling and other expenses)
account to the Buyer for the excess over sums owing
by the Buyer or charge the Buyer for any shortfall.
The following provisions set out FBUK’s entire liability whether
arising in contract, tort (including negligence), misrepresentation
(other than fraudulent misrepresentation) or otherwise
howsoever arising.
AND THE BUYER’S ATTENTION IS IN PARTICULAR DRAWN
TO THE FOLLOWING PROVISIONS OF THIS CONDITION
12.7. To the extent the law does not permit such liability to be
excluded:
The Goods may be delivered in instalments. Each delivery shall
constitute a separate contract and failure by FBUK to deliver
any one or more of the instalments in accordance with these
Conditions or any claim by the Buyer in respect of any one or
more instalments shall not entitle the Buyer to treat the Contract
as a whole as repudiated.
10.4. If the Buyer fails to take delivery of the Goods or fails to give
FBUK adequate delivery instructions within 14 days of their
availability FBUK may:
10.6. Where FBUK arranges forwarding of the Goods, the Buyer shall
notify FBUK and the carrier in writing within 48 hours of delivery
of any damage to the Goods or shortage in delivery.
The Buyer shall inspect the Goods on receipt and notify FBUK
of any defects within 7 days of delivery failing which the Buyer
shall be deemed to have accepted them. After acceptance the
Buyer shall not be entitled to reject Goods. The Buyer shall not
be entitled to reject the Goods for any defect or failure which is
so slight that it would be unreasonable to reject them.
11. RISK AND PROPERTY
11.1. 12.3.5. in items not manufactured by FBUK, when the Buyer
shall only be entitled to the benefit of any such
warranty as is given to FBUK by the manufacturer.
12.4. 10.3. 10.5. 12.3.4. if any sum owing by the Buyer to FBUK has not been
paid;
The method of delivery shall be in accordance with FBUK’s
quotation. The Buyer must obtain any import or export licences
required.
Any dates given for delivery of the Goods or provision of
services are approximate only and FBUK shall not be liable for
any delay howsoever caused. Time for delivery or performance
shall not be of the essence.
Notwithstanding any other provision of these Conditions, the
property in the Goods shall not pass to the Buyer until FBUK has
received in cash or cleared funds payment in full of all sums due
under the Contract and all other contracts between the Buyer
and FBUK (whether or not the sums due under those contracts
are immediately due and payable). Until then the Buyer shall:
12.7.1. FBUK’s liability to the Buyer for death or injury resulting
from its negligence shall not be limited;
12.7.2. FBUK accepts liability to the Buyer for damage to
the tangible property of the Buyer resulting from the
negligence of FBUK not exceeding £1,000,000 for
any one incident or series of incidents arising from a
common cause;
Risk in the Goods shall pass to the Buyer when FBUK notifies
Catalogue 2015
97
12.7.3. Save as otherwise expressly provided, FBUK’s entire
liability shall be limited to damages of an amount equal
to the price due under the Contract.
12.8. 12.9. Subject to condition 12.7.1 above, FBUK shall not be liable
for any increased costs, expenses, loss of profits, goodwill,
business, contracts, revenues or anticipated savings or any
type of special indirect or consequential loss (including loss or
damage suffered by the Buyer as a result of a claim by a third
party) even if such loss was reasonably foreseeable or FBUK had
been advised of the possibility of the Buyer incurring the same.
FBUK shall not be liable to the Buyer or be deemed to be in
breach of the Contract by reason of any delay in performing, or
any failure to perform, any of FBUK’s obligations, if the delay or
failure was due to any cause beyond FBUK’s reasonable control
including (without limitation) flood, fire, accident, transportation
delays, strikes, war or threat of war, sabotage, civil disturbance
or governmental action, disruption of supplies or services.
12.10. Save as otherwise expressly provided, the Buyer shall indemnify
FBUK against any cost, claim, expense, loss or liability made by
any person in connection with the Goods or their use.
replace and supersede any prior arrangement, understanding,
warranty or representation (other than any fraudulent
misrepresentation).
16.7.
FBUK’s rights are cumulative and in addition to any rights
available to it at common law.
16.8. The Contract shall be governed by the laws of England and
Wales and, subject to clause, 16.9 the parties submit to the
exclusive jurisdiction of the courts of England and Wales. For
the avoidance of doubt, the United Nations Convention on the
International Sale of Goods shall not apply to the Contract.
16.9.
Nothing in these Conditions shall limit the right of FBUK to take
proceedings against the Buyer in any other court of competent
jurisdiction, nor shall the taking of proceedings in any one or
more jurisdiction preclude the taking of proceedings in any
other jurisdiction, whether concurrently or not, to the extent
permitted by the law of such other jurisdiction.
16.10. No term of this contract shall be enforceable under the
Contracts (Rights of Third Parties) Act 1999 by a third party.
16.11
These Conditions are drafted in the English language. If these
Conditions are translated into any other language, the English
language text shall prevail.
16.12
Any notice given under or in connection with the Contract
shall be in the English language. All other documents provided
under or in connection with the Contract shall be in the English
language.
13. INSOLVENCY AND BREACH
13.1. If the Buyer fails to make any payment when due or breaches
any provision of the Contract; or FBUK reasonably apprehends
that the solvency of the Buyer may be in jeopardy FBUK may
cancel the Contract or suspend any further deliveries under the
Contract without any liability to the Buyer, and if the Goods
have been delivered but not paid for the price shall become
immediately due and payable notwithstanding any previous
agreement or arrangement to the contrary.
14. SAFETY, OPERATING AND MAINTENANCE INSTRUCTIONS
The Buyer’s attention is directed to the instructions for use and
cautionary notes supplied with the Goods, as well as other
technical literature.
15. STANDARD OF COATING ATTAINED
The Buyer shall follow FBUK’s instructions on operation and
maintenance. FBUK accepts no responsibility for unsatisfactory
results due to use of coating materials not recommended
in writing by FBUK or whose composition or quality when
supplied is different from that tested by FBUK when giving its
recommendation.
16. GENERAL
16.1. FBUK may assign its rights and obligations. The Buyer may not
assign its rights and obligations.
16.2. Any notice shall be in writing addressed to the addressee at
its registered office or principal place of business or such other
address as may have been notified by the party giving the
notice.
16.3. Any notice is deemed to have been received:
16.3.1. if delivered personally, at the time of delivery; or
16.3.2. if sent by commercial courier, at the time of signature
of the courier’s delivery receipt; or
16.3.3. in the case of pre-paid first class post or recorded
delivery, 9.00 am on the second Business Day after
posting; or
16.3.4. in the case of airmail, 9.00 am on the fifth Business Day
after posting.
98
16.4.
No delay or failure by FBUK in enforcing or partially enforcing
any provision of the Contract shall constitute a waiver of that
provision or any other provision. No waiver by FBUK shall be
considered as a waiver of any subsequent breach of the same or
any other provision. No waiver by FBUK shall be effective unless
in writing.
16.5. If any provision of these Conditions is held by any competent
authority to be invalid or unenforceable in whole or in part the
validity of the other provisions of these Conditions and the
remainder of the provision in question shall not be affected.
16.6. These Conditions constitute the entire agreement between
FBUK and the Buyer concerning the supply of the Goods and
Catalogue 2015
A guide to the DSEAR and ATEX Directives
What is DSEAR and ATEX?
The EU Directives 94/4/EC (ATEX 95) “Equipment for use in potentially explosive atmospheres” and the “Workplace directive” 1999/92/EC (ATEX
137) are the European directives, which ensure employers work practices and manufacturers of equipment used in potentially explosive atmospheres,
are safe and do not create potential explosion hazards. In other words, its all about health and safety at work for workers who handle and work with
flammable and dangerous materials, to ensure they are not at risk of an explosion from the equipment and work practices.
The ATEX directives are implemented into UK law by the regulations “Dangerous Substances and Explosive Atmospheres Regulations” known as
DSEAR 2002 and the “Equipment and protective systems for use in potentially explosive atmospheres” regulations 1996. DSEAR became mandatory
in July 2006. DSEAR is a legal Health and Safety requirement which is enforced by the HSE, local authorities and in part the fire service.
ATEX Compliance
As a manufacturer of equipment used in potentially explosive
atmospheres, we comply with this directive by applying the CE mark
along with the Explosion protection symbol
and other markings
to show compliance of that product.
Each piece of equipment must be marked with information to enable
the user to assess its suitability to be used in the environment it is
intended to be used in. The equipment could be marked with the
following;
l Name and address of Manufacturer
l The CE mark
l If the equipment has been certified by a Notified Body, their
reference follows the CE mark
l Equipment model number/name/type
l Year of manufacture
l The Explosion protection Symbol
l The equipment Group II and category 1, 2 or 3
l For Gas (G) e.g. Group 2, Cat 2 Gas
Workplace regulations DSEAR 2002
The ATEX 1999/92/EC workplace regulations are implemented in the
UK through the DSEAR 2002 Regulations. The duties for employers
and owners under DSEAR are;
l Carry out a risk assessment of work involving dangerous
substances and eliminate or reduce any risks identified.
l Provide equipment and procedures for accidents and
emergencies.
l Instruct and train employees.
l Areas where hazardous explosive atmospheres may occur are
classified into zones and where necessary marked with a specified
“EX” sign at their points of entry; (eg spray booths, mix rooms,
paint stores etc).
l Provide equipment and protective systems which comply
with ATEX Regulations appropriate for the Zone rating of the
hazardous area.
l Document all the above in an Explosion Protection Document.
Typical Markings found on Hazardous Area Equipment
Name and Address
of Manufacturer
Specific Marking of
Explosive Protection
Equipment
Group
Category
FINISHING BRANDS UK
BOURNEMOUTH
CE
Mark
FINISHING BRANDS
UK
and number BH11 9LH, UK
BOURNEMOUTH
of Notified
BH11 9LH, UK
Body
FINISHING BRANDS UK
BOURNEMOUTH
Model
BH11 9LH, UK
or Type
EC Type Examination Certificate
Number
Gas
or Dust
Protection
Concept
Gas Group
Temperature Class
Ambient
Temperature range
Example of DGi Serial Number:
First 2 numbers denote year, 3rd and 4th
denote month, eg March = 03, 5th and
6th denote day. remaining 5 numbers
are sequential, reset at 00001 at start of
New Year.
FINISHING BRANDS UK
BH11 9LH, UK
Typical
Markings
foundUK
on Sprayguns
FINISHING
BRANDS
BH11 9LH, UK
Name and Address
of Manufacturer
FINISHING BRANDS UK
BH11 9LH, UK
CE Mark
Model or Type
Equipment
Group
Category 2
Special
Conditions for
safe Use
Gas
Avoidance of Hazards associated with Spraying
flammable materials
The main hazard with spraying is electrostatic discharges and mechanically generated sparks. To avoid these ignition hazards, you should;
l Only use equipment CE marked to ATEX regulations. Most Finishing Brands Products are CE marked to ATEX eg Sprayguns, Digital Gauge, hoses.
If in doubt, contact your distributor or Finishing Brands.
l The equipment must be installed and used in accordance with the instructions provided by the manufacturer(s).
l Ensure metallic parts of the equipment are earthed and bonded together (e.g. pressure feed tanks and pumps) to avoid potential differences
between them. Metallic portable containers must be bonded and earthed. Check earth continuity at regular intervals. Keep earthing points clean.
l Use conductive air and fluid hoses to avoid static charging from air and fluid flows.
l Equip Operators with anti-static clothing and conductive footwear. Remove contaminated clothing if leaving the workplace into areas where
ignitions hazards may occur e.g. smoking.
l Clean equipment with non-flammable liquids, or use safety cans with flame arrestors for use with flammable liquids.
l Removal of paint residues with scrapers made of plastic or non-sparking materials (steel scrapers can create sparks). Coat walls with strippable/
peelable coatings to avoid removal of residues by mechanical means.
More information can be found at the HSE DSEAR website: http://www.hse.gov.uk/fireandexplosion/dsear.htm
Catalogue 2015
99
Download PDF
Similar pages