®

1.9 4WD ELECTRIC SCALE CRAWLER RTR

ECX01009 | ECX01009I

Congratulations on your purchase of the ECX

®

Barrage

™

1.9 4WD Electric Scaler.

This model introduces you to the sport of RC driving.

INSTRUCTION MANUAL

BEDIENUNGSANLEITUNG

MANUEL D’UTILISATION

MANUALE DI ISTRUZIONI

Herzlichen Glückwunsch zum kauf des ECX Barrage 1.9 4WD Electric Scaler.

Dieses Modell ist der gelungende Einstieg in die Welt des RC Cars Sports.

Nous vous félicitons pour l’achat de l’ECX Barrage 1,9 4WD électrique. Ce modèle vous permettra de découvrir l’univers du RC.

Congratulazioni per l’acquisto dell’ECX Barrage 1.9 4WD Electric Scaler. Questo modello dà accesso al mondo degli automodelli radiocomandati.

EN

NOTICE

All instructions, warranties and other collateral documents are subject to change at the sole discretion of Horizon Hobby, LLC. For up-to-date product literature, visit http://www.horizonhobby.com and click on the support tab for this product.

MEANING OF SPECIAL LANGUAGE

The following terms are used throughout the product literature to indicate various levels of potential harm when operating this product:

NOTICE: Procedures, which if not properly followed, create a possibility of physical property damage AND little or no possibility of injury.

CAUTION: Procedures, which if not properly followed, create the probability of physical property damage AND a possibility of serious injury.

WARNING: Procedures, which if not properly followed, create the probability of property damage, collateral damage, and serious injury OR create a high probability of superficial injury.

WARNING: Read the ENTIRE instruction manual to become familiar with the features of the product before operating. Failure to operate the product correctly can result in damage to the product, personal property and cause serious injury.

This is a sophisticated hobby product and NOT a toy. It must be operated with caution and common sense and requires some basic mechanical ability.

Failure to operate this Product in a safe and responsible manner could result in injury or damage to the product or other property. This product is not intended for use by children without direct adult supervision. Do not use with incompatible components or alter this product in any way outside of the instructions provided by Horizon Hobby, LLC. This manual contains instructions for safety, operation and maintenance. It is essential to read and follow all the instructions and warnings in the manual, prior to assembly, setup or use, in order to operate correctly and avoid damage or serious injury.

Age Recommendation: Not for children under 14 years. This is not a toy.

Safety Precautions and Warnings

As the user of this product, you are solely responsible for operating in a manner that does not endanger yourself and others or result in damage to the product or property of others.

This model is controlled by a radio signal subject to interference from many sources outside your control. This interference can cause momentary loss of control, so it is advisable to always keep a safe distance in all directions around your model as this margin will help avoid collisions or injury.

• Never operate your model with low transmitter batteries.

• Always operate your model in open spaces away from full-size vehicles, traffic and people.

• Never operate the model in the street or in populated areas for any reason.

• Carefully follow the directions and warnings for this and any optional support equipment (chargers, rechargeable battery packs, etc.) you use.

• Keep all chemicals, small parts and anything electrical out of the reach of children.

• Never lick or place any portion of the model in your mouth as it could cause serious injury or even death.

• Exercise caution when using tools and sharp instruments.

• Take care during maintenance as some parts may have sharp edges.

• Immediately after using your model, do NOT touch equipment such as the motor, electronic speed control and battery, because they generate high temperatures. You may burn yourself seriously touching them.

• Do not put fingers or any objects inside rotating and moving parts, as this may cause damage or serious injury.

• Always turn on your transmitter before you turn on the receiver in the car.

Always turn off the receiver before turning your transmitter off.

• Keep the wheels of the model off the ground when checking the operation of the radio equipment.

WATER-RESISTANT VEHICLE WITH WATERPROOF ELECTRONICS

Your new Horizon Hobby vehicle has been designed and built with a combination of waterproof and water-resistant components to allow you to operate the product in many “wet conditions,” including puddles, creeks, wet grass, snow and even rain.

While the entire vehicle is highly water-resistant, it is not completely waterproof and your vehicle should NOT be treated like a submarine.

The various electronic components used in the vehicle, such as the

Electronic Speed Control (ESC) and servo(s) are waterproof, however, most of the mechanical components are water-resistant and should not be submerged.

Metal parts, including the bearings, hinge pins, screws and nuts, as well as the contacts in the electrical cables, will be susceptible to corrosion if additional maintenance is not performed after running in wet conditions.

To maximize the long-term performance of your vehicle and to keep the warranty intact, the procedures described in the “Wet Conditions

Maintenance” section below must be performed regularly if you choose to run in wet conditions. If you are not willing to perform the additional care and maintenance required, then you should not operate the vehicle in those conditions.

CAUTION: Failure to exercise caution while using this product and complying with the following precautions could result in product malfunction and/or void the warranty.

General Precautions

• Read through the wet conditions maintenance procedures and make sure that you have all the tools you will need to properly maintain your vehicle.

• Not all batteries can be used in wet conditions. Consult the battery manufacturer before use. Do not use Li-Po batteries in wet conditions.

• The included transmitter is not waterproof or water-resistant. If using a different transmitter than the one included, consult your transmitter's manual or the manufacturer before operation.

• Never operate your transmitter or vehicle where lightning may be present.

• Do not operate your vehicle where it could come in contact with salt water (ocean water or water on salt-covered roads), contaminated or polluted water. Salt water is very conductive and highly corrosive, so use caution.

• Even minimal water contact can reduce the life of your motor if it has not been certified as water-resistant or waterproof. If the motor becomes excessively wet, apply very light throttle until the water is mostly removed from the motor. Running a wet motor at high speeds may rapidly damage the motor.

• Driving in wet conditions can reduce the life of the motor. The additional resistance of operating in water causes excess strain. Alter the gear ratio by using a smaller pinion or larger spur gear. This will increase torque (and motor life) when running in mud, deeper puddles, or any wet conditions that will increase the load on the motor for an extended period of time.

2

Wet Conditions Maintenance

• Remove the battery pack(s) and dry the contacts. If you have an air compressor or a can of compressed air, blow out any water that may be inside the recessed connector housing.

• Remove the tires/wheels from the vehicle and gently rinse the mud and dirt off with a garden hose. Avoid rinsing the bearings and transmission.

NOTICE: Never use a pressure washer to clean your vehicle.

• Use an air compressor or a can of compressed air to dry the vehicle and help remove any water that may have gotten into small crevices or corners.

• Spray the bearings, drive train, fasteners and other metal parts with a water-displacing light oil or lubricant. Do not spray the motor.

• Let the vehicle air dry before you store it. Water (and oil) may continue to drip for a few hours.

• Increase the frequency of disassembly, inspection and lubrication of the following:

• Front and rear axle hub assembly bearings.

• All transmission cases, gears and differentials.

• Motor—clean with an aerosol motor cleaner and re-oil the bushings with lightweight motor oil.

EN

Transmitter

Frequency 2.4GHz

Battery AA x 4

Servo

Power Supply

Output Torque

Operating Speed

Size

4.8V~6V

5 oz (1.5 kg-cm)

0.15sec/60 degrees of travel

40 x 20.3 x 38mm

SPECIFICATIONS

Electronic Speed Control (ESC)

Input Voltage

Electric Capacity

PWM Frequency

BEC Voltage

Size

Weight

6.0–8.4V

60A ESC

1kHz

5V/2A

46.5 x 34 x 28.5mm

65 g

COMPONENTS

• ECX

®

Barrage

™

Scaler

• ECX

®

2.4GHz 2-CH V3 Transmitter

• AA (4) Batteries

• 100mAh NiMH Wall Charger with EC3™ Connector

• Dynamite ® Speedpack ® 900mAh NiMH battery with

EC3™ Connector

• Dynamite

®

Tazer™ 370 Brushed Motor

• Dynamite

®

60A WP FWD/REV Brushed ESC

• ECX

®

2.4GHz 2-CH V3 Receiver

• Spektrum™ Digital Servo (SPMS602)

TABLE OF CONTENTS

Quick Start....................................................................................................4

Vehicle Preparations ....................................................................................4

Charging the Vehicle Battery .......................................................................4

Charging Warnings ......................................................................................4

Installing the Battery....................................................................................5

Transmitter Controls .....................................................................................5

Installing Transmitter Batteries ...................................................................5

Binding .........................................................................................................6

Getting Started.............................................................................................6

Operation......................................................................................................7

When You Are Finished................................................................................7

Motor Care ...................................................................................................7

Maintenance ................................................................................................8

Setting the Gear Mesh.................................................................................8

Electronic Speed Control (ESC) ....................................................................8

Troubleshooting Guide .................................................................................9

Limited Warranty .......................................................................................10

Warranty and Service Contact Information ...............................................11

FCC Information..........................................................................................11

IC Information.............................................................................................11

Replacement Parts .............................................................................. 40–41

Optional Parts.............................................................................................41

Parts Diagram...................................................................................... 41–43

1.9 4WD ELECTRIC SCALE CRAWLER RTR

3

EN

QUICK START

Please read the entire manual to gain a full understanding of the vehicle, fine-tuning the setup and performing maintenance.

1. Read the safety precautions found in this manual.

2. Charge a battery for the vehicle. Refer to the included charging warnings and instructions for battery charging information.

3. Install the AA batteries in the transmitter. Only use alkaline or rechargeable batteries.

4. Install the fully charged battery in the vehicle.

5. Power ON the transmitter and then the vehicle. Wait 5 seconds for the ESC to initialize. Always power the transmitter ON before the vehicle and power it OFF after the vehicle has been powered OFF.

6. Check the steering and throttle control directions. Verify that the servos are moving in the correct direction.

7. Drive your vehicle.

8. Perform any necessary maintenance.

VEHICLE PREPARATIONS

CHARGING THE VEHICLE BATTERY

NOTICE: Never charge a battery in the vehicle or damage may result.

CHARGING WARNINGS

WARNING: Failure to exercise caution while using this product and comply with the following warnings could result in product malfunction, electrical issues, excessive heat, FIRE, and ultimately injury and property damage.

1. Connect the NiMH battery to the battery charger.

2. Connect the charger to an AC power outlet.

3. Allow the NiMH battery to charge for 9 hours.

• NEVER LEAVE CHARGING BATTERIES UNATTENDED.

• NEVER CHARGE BATTERIES OVERNIGHT.

• Read all safety precautions and literature prior to use of this product.

• Never leave the battery and charger unattended during use.

• Never allow children under 14 years of age to charge battery packs.

• Never attempt to charge dead or damaged batteries.

• Never charge a battery if the cable has been pinched or shorted.

• Never allow batteries or charger to come into contact with moisture at any time.

• Never charge batteries in extremely hot or cold places (recommended between 50–80°F (10–26°C)) or place in direct sunlight.

• Always use only Ni-MH rechargeable batteries. This charger cannot charge batteries such as “heavy duty,” “alkaline,” “mercury” or

“lithium” battery.

• Always connect to the charger correctly.

• Always disconnect the battery and charger after charging and let them cool between charges.

• Always inspect the battery before charging.

• Always terminate all processes and contact Horizon Hobby if the product malfunctions.

• Always make sure you know the specifications of the battery to be charged or discharged to ensure it meets the requirements of this charger.

• Always constantly monitor the temperature of the battery pack while charging.

• Always end the charging process if the charger or battery becomes hot to the touch or starts to change form during the charge process.

• Always charge in a well ventilated area.

4

INSTALLING THE BATTERY

1. Remove the vehicle body.

2. Install a fully charged battery.

3. Secure the battery pack using the hook and loop straps.

4. Connect the battery pack to the ESC power connector.

CAUTION: Connecting the battery to the ESC with reversed polarity will cause damage to the ESC, the battery or both. Damage caused by incorrectly connecting the battery is not covered under warranty.

TRANSMITTER CONTROLS

BATTERY LEVEL INDICATOR

Solid Red and Green:

Battery voltage is good

(above 4V).

Solid Red: Battery voltage is critically low (below

4V). Replace transmitter batteries.

THROTTLE DUAL RATE

Adjusts the maximum amount of throttle the vehicle can be given

STEERING DUAL RATE

Adjusts the amount the steering moves when the steering wheel is turned left or right

REVERSE SWITCH

Allows you to change the direction of steering (ST.

REV) and throttle (TH. REV) controls (Ensure proper function with a radio system test).

POWER SWITCH

Power on or off the transmitter

STEERING WHEEL

THROTTLE TRIM

Adjusts the neutral point of the electronic speed control

Control steering.

Right and Left steering

THROTTLE TRIGGER

STEERING TRIM

Adjust to make the vehicle drive straight with no input at the steering wheel

Reverse

Controls power to the motor for forward or reverse

Forward

Stop

INSTALLING TRANSMITTER BATTERIES

This transmitter requires 4 AA batteries.

1. Remove the battery cover from the transmitter.

2. Install the batteries as shown.

3. Install the battery cover.

CAUTION: If using rechargeable batteries, charge only rechargeable batteries. Charging non-rechargeable batteries may cause the batteries to burst, resulting in injury to persons and/or damage to property.

CAUTION: Risk of explosion if battery is replaced by an incorrect type. Dispose of used batteries according to national regulations.

1.9 4WD ELECTRIC SCALE CRAWLER RTR

5

EN

EN

BINDING

The included transmitter and receiver are bound at the factory. If you need to rebind, follow the instructions below.

1. Power off the transmitter and ESC.

2. Connect a fully charged battery pack to the ESC.

3. Power on the ESC. The RED LED on the receiver flashes.

4. Press and release the bind button (A) on the receiver.

The RED LED on the receiver flashes rapidly.

5. Power on the transmitter.

6. The RED LED on the receiver turns solid when the radio system is bound.

You must rebind when binding the receiver to a different transmitter.

A

NOTICE: Do not attempt to bind the transmitter and receiver if there are other compatible transmitters in bind mode within 400 feet. Doing so may result in unexpected binding.

GETTING STARTED

1. Power on the transmitter.

2. Connect the battery to the Electronic Speed Control

(ESC) / Receiver unit and power on the vehicle .

3. Perform a test of the transmitter’s control of the vehicle with the vehicle’s wheels off the ground.

4. Start driving slowly, and, if the vehicle does not go straight, adjust the steering trim dial on the transmitter.

IMPORTANT: Seat the motor brushes by driving smoothly on a flat surface during use of the first battery charge. Properly seating the motor brushes will increase the life and performance of the motor.

6

OPERATION

• ALWAYS turn on your transmitter before you turn on the receiver in the vehicle. Always power off the receiver before turning your transmitter off.

• ALWAYS operate your vehicle in a wide open area. Operating the vehicle in a small space or indoors can cause overheating at low speeds. Operating at low speed increases heat in the electronic speed control (ESC). Overheating can damage the vehicle and failure may result.

EN

1. Power off the ESC.

WHEN YOU ARE FINISHED

2. Disconnect the battery.

3. Power off the transmitter.

4. Remove the battery from the vehicle.

5. Recharge the battery.

MOTOR CARE

• Seat the motor brushes by driving smoothly on a flat surface during use of the first battery charge. Failing to do so can greatly

reduce motor performance and functional life.

• Prolong motor life by preventing overheating conditions.

Undue motor wear results from frequent turns, stops and starts, pushing objects, driving in deep water and tall grass, and driving continuously up hill. Allow the motor to cool completely

before running the vehicle.

• Over-temperature protection is installed on the ESC to prevent circuit damage, but cannot protect the motor from driving against heavy resistance.

1.9 4WD ELECTRIC SCALE CRAWLER RTR

7

EN

MAINTENANCE

SETTING THE GEAR MESH

The gear mesh has already been set at the factory. Setting the gear mesh is only necessary when changing motors or gears.

You must remove the vehicle’s gear cover (A) to make this adjustment.

Proper gear mesh (how the gear teeth meet) is important to the performance of the vehicle. When the gear mesh is too loose, the spur gear could be damaged by the pinion gear of the motor. If the mesh is too tight, speed could be limited and the motor and ESC will overheat.

Set the gear mesh by following these simple steps:

1. Loosen the 2 motor screws (B).

2. Put a small piece of paper (C) between the pinion and spur gears.

3. Push the gears together while tightening the motor screws.

B

C

A

4. Rotate the gears to remove the paper. The gearing should move a small amount.

5. Reinstall the gear cover.

ELECTRONIC SPEED CONTROL (ESC)

Connecting

1. Connect the RED (+) ESC wire to the RED (+) motor wire.

2. Connect the BLACK (–) ESC wire to the BLACK (–) motor wire.

NOTICE: Always disconnect the battery from the ESC when you have finished operating your vehicle. The ESC’s switch only controls power to the receiver and servos. The ESC will continue to draw current when connected to the battery, resulting in possible damage to the battery through over-discharge.

Calibrating

Ensure proper ESC function by calibrating the ESC to your transmitter inputs.

1. Power OFF the ESC.

2. Ensure your transmitter is powered ON, the throttle is not reversed, the throttle trim is neutral and the throttle travel range is at 100%.

3. Keep the throttle at neutral and power ON the ESC.

4. The ESC automatically calibrates the throttle range after 3 seconds.

5. One long beep will sound when the ESC is ready to run.

Programming

The ESC comes with two jumpers pre-installed in the MODE: Forward/

Brake/Reverse) and BATT: Ni-MH configurations.

To change the mode to F/B/R (forward/brake/reverse) or F/R (forward/ reverse) or change the battery type to Li-Po:

1. Power OFF the ESC.

2. Disconnect the jumper from the default port and connect it to the desired port.

3. Power ON the ESC.

If the jumpers are lost or not installed, the ESC will default to MODE:

F/B/R and BATT: Li-Po.

WARNING: Do not connect bind plugs or receiver servo leads into the ESC programming port. Doing so may damge the ESC and/or components.

Mode

Battery

(BATT)

Forward/

Brake/

Reverse

(F/B/R)

Forward/

Brake

(F/B)

Li-Po Ni-MH

Forward/

Reverse

(F/R ((Crawler

Mode))

8

TROUBLESHOOTING GUIDE

Problem

Short Run Time

Sluggish Action

Controls Reversed

Motor/ESC overheat

Does Not Operate

Poor Range

The system will not connect

Possible Cause

Battery damaged/not charged

Motor dirty

Motor dirty

Bind in drivetrain

Vehicle battery is not charged

ST. REV or TH. REV

Over-geared for the driving environment

Transmitter batteries low

Transmitter powered off

ESC powered off

Vehicle battery is not charged

Dual-rate (D/R) steering and/or throttle knobs on transmitter are turned to zero

Transmitter batteries low

Receiver antenna damaged

Transmitter and receiver too near each other

Transmitter and receiver too near large metal objects (vehicles, etc.)

Throttle trim out of center on transmitter

Solution

Check/change battery

Check/clean

Check/clean

Clean/adjust

Replace/recharge

Change switch position

Install smaller pinion on the motor

Replace/recharge

Power on

Power on

Replace/recharge

Adjust dual-rate (D/R) steering and/or throttle knobs to 10

Replace/recharge

Check/repair/replace

Move transmitter 3.3–9.8ft (1–3m) from receiver

Move away from large metal objects (vehicles, etc.)

Set throttle trim on transmitter to zero. Turn off and on transmitter and vehicle

Rebind transmitter and receiver

Receiver accidentally put in bind mode so receiver is no longer bound

The receiver goes into failsafe mode a short distance away from the transmitter

Check the receiver antenna to be sure it is not cut or damaged

The receiver quits responding during operation

Receiver and transmitter are not bound

Vehicle moves forward or backward without input from user

Car does not drive straight

Low battery voltage

Loose or damaged wires or connectors between battery and receiver

Transmitter accidentally put in bind mode, ending bind to receiver

Throttle trim on transmitter not centered

Steering trim on transmitter not centered

No steering or lack of steering

Steering dual-rate (D/R) not adjusted correctly

Servo failed

No throttle or lack of throttle

Clicking noise in transmission area

Throttle dual-rate (D/R) not adjusted correctly

ESC failed

Motor failed

Dirt or rocks in spur gear

Motor moved away from spur gear

Make sure the antenna is in the antenna tube

Contact Horizon Product Support

Completely recharge battery

Do a check of the wires and connection between battery and receiver. Repair or replace wires and/or connectors

Bind transmitter to receiver

Adjust throttle trim to set neutral point

Adjust steering trim so vehicle drives straight

Adjusts steering dual-rate (D/R) knob on transmitter to desired steering throw

Contact Horizon Product Support

Adjust the throttle dual-rate (D/R) knob on transmitter to desired steering throw

Contact Horizon Product Support

Contact Horizon Product Support

Remove gear cover and inspect. If necessary, replace gear

Reset gear mesh

EN

1.9 4WD ELECTRIC SCALE CRAWLER RTR

9

EN

LIMITED WARRANTY

What this Warranty Covers

Horizon Hobby, LLC, (Horizon) warrants to the original purchaser that the product purchased (the “Product”) will be free from defects in materials and workmanship at the date of purchase. that you may need any assistance. For questions or assistance, please visit our website at www.horizonhobby.com, submit a Product Support Inquiry, or call the toll free telephone number referenced in the Warranty and Service

Contact Information section to speak with a Product Support representative.

What is Not Covered

This warranty is not transferable and does not cover (i) cosmetic damage, (ii) damage due to acts of God, accident, misuse, abuse, negligence, commercial use, or due to improper use, installation, operation or maintenance, (iii) modification of or to any part of the Product, (iv) attempted service by anyone other than a Horizon Hobby authorized service center, (v) Product not purchased from an authorized Horizon dealer, or (vi) Product not compliant with applicable technical regulations or (vii) use that violates any applicable laws, rules, or regulations.

OTHER THAN THE EXPRESS WARRANTY ABOVE, HORIZON MAKES NO

OTHER WARRANTY OR REPRESENTATION, AND HEREBY DISCLAIMS ANY

AND ALL IMPLIED WARRANTIES, INCLUDING, WITHOUT LIMITATION, THE

IMPLIED WARRANTIES OF NON-INFRINGEMENT, MERCHANTABILITY AND

FITNESS FOR A PARTICULAR PURPOSE. THE PURCHASER ACKNOWLEDGES

THAT THEY ALONE HAVE DETERMINED THAT THE PRODUCT WILL SUITABLY

MEET THE REQUIREMENTS OF THE PURCHASER’S INTENDED USE.

Purchaser’s Remedy

Horizon’s sole obligation and purchaser’s sole and exclusive remedy shall be that Horizon will, at its option, either (i) service, or (ii) replace, any Product determined by Horizon to be defective. Horizon reserves the right to inspect any and all Product(s) involved in a warranty claim. Service or replacement decisions are at the sole discretion of Horizon. Proof of purchase is required for all warranty claims. SERVICE OR REPLACEMENT AS PROVIDED UNDER

THIS WARRANTY IS THE PURCHASER’S SOLE AND EXCLUSIVE REMEDY.

Inspection or Services

If this Product needs to be inspected or serviced and is compliant in the country you live and use the Product in, please use the Horizon Online Service Request submission process found on our website or call Horizon to obtain a Return

Merchandise Authorization (RMA) number. Pack the Product securely using a shipping carton. Please note that original boxes may be included, but are not designed to withstand the rigors of shipping without additional protection.

Ship via a carrier that provides tracking and insurance for lost or damaged parcels, as Horizon is not responsible for merchandise until it arrives and is accepted at our facility. An Online Service Request is available at http://www.

horizonhobby.com/content/service-center_render-service-center. If you do not have internet access, please contact Horizon Product Support to obtain a

RMA number along with instructions for submitting your product for service.

When calling Horizon, you will be asked to provide your complete name, street address, email address and phone number where you can be reached during business hours. When sending product into Horizon, please include your RMA number, a list of the included items, and a brief summary of the problem. A copy of your original sales receipt must be included for warranty consideration.

Be sure your name, address, and RMA number are clearly written on the outside of the shipping carton.

NOTICE: Do not ship Li-Po batteries to Horizon. If you have any issue with a Li-Po battery, please contact the appropriate Horizon

Product Support office.

Warranty Requirements

For Warranty consideration, you must include your original sales

receipt verifying the proof-of-purchase date. Provided warranty conditions have been met, your Product will be serviced or replaced free of charge. Service or replacement decisions are at the sole discretion of Horizon.

Limitation of Liability

HORIZON SHALL NOT BE LIABLE FOR SPECIAL, INDIRECT, INCIDENTAL

OR CONSEQUENTIAL DAMAGES, LOSS OF PROFITS OR PRODUCTION OR

COMMERCIAL LOSS IN ANY WAY, REGARDLESS OF WHETHER SUCH CLAIM

IS BASED IN CONTRACT, WARRANTY, TORT, NEGLIGENCE, STRICT LIABILITY

OR ANY OTHER THEORY OF LIABILITY, EVEN IF HORIZON HAS BEEN

ADVISED OF THE POSSIBILITY OF SUCH DAMAGES. Further, in no event shall the liability of Horizon exceed the individual price of the Product on which liability is asserted. As Horizon has no control over use, setup, final assembly, modification or misuse, no liability shall be assumed nor accepted for any resulting damage or injury. By the act of use, setup or assembly, the user accepts all resulting liability. If you as the purchaser or user are not prepared to accept the liability associated with the use of the Product, purchaser is advised to return the Product immediately in new and unused condition to the place of purchase.

Law

These terms are governed by Illinois law (without regard to conflict of law principals). This warranty gives you specific legal rights, and you may also have other rights which vary from state to state. Horizon reserves the right to change or modify this warranty at any time without notice.

WARRANTY SERVICES

Questions, Assistance, and Services

Your local hobby store and/or place of purchase cannot provide warranty support or service. Once assembly, setup or use of the Product has been started, you must contact your local distributor or Horizon directly. This will enable Horizon to better answer your questions and service you in the event

Non-Warranty Service

Should your service not be covered by warranty, service will be completed and payment will be required without notification or estimate of the expense unless the expense exceeds 50% of the

retail purchase cost. By submitting the item for service you are agreeing to payment of the service without notification. Service estimates are available upon request. You must include this request with your item submitted for service. Non-warranty service estimates will be billed a minimum of ½ hour of labor. In addition you will be billed for return freight. Horizon accepts money orders and cashier’s checks, as well as Visa, MasterCard, American Express, and Discover cards. By submitting any item to Horizon for service, you are agreeing to Horizon’s Terms and Conditions found on our website http://www.

horizonhobby.com/content/service-center_render-service-center.

ATTENTION: Horizon service is limited to Product compliant in the country of use and ownership. If received, a non-compliant

Product will not be serviced. Further, the sender will be responsible for arranging return shipment of the un-serviced

Product, through a carrier of the sender’s choice and at the sender’s expense. Horizon will hold non-compliant Product for a period of 60 days from notification, after which it will be discarded.

10/15

10

WARRANTY AND SERVICE CONTACT INFORMATION

Country of

Purchase

Horizon Hobby Contact Information

United States of America

Horizon Service Center

(Repairs and Repair Requests)

Horizon Product Support

(Product Technical Assistance) servicecenter.horizonhobby.com/

RequestForm/ [email protected]

European Union

Sales

Horizon Technischer Service

Sales: Horizon Hobby GmbH

877-504-0233 [email protected]

800-338-4639 [email protected]

+49 (0) 4121 2655 100

Address

4105 Fieldstone Rd

Champaign, Illinois, 61822 USA

Hanskampring 9

D 22885 Barsbüttel, Germany

EN

FCC INFORMATION

FCC Number: BRWECX13002 This device complies with part 15 of the FCC rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.

CAUTION: Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.

This product contains a radio transmitter with wireless technology which has been tested and found to be compliant with the applicable regulations governing a radio transmitter in the 2.400GHz to 2.4835GHz frequency range.

Antenna Separation Distance

When operating your Spektrum transmitter, please be sure to maintain a separation distance of at least 5 cm between your body

(excluding fingers, hands, wrists, ankles and feet) and the antenna to meet RF exposure safety requirements as determined by FCC regulations.

The following illustrations show the approximate 5 cm RF exposure area and typical hand placement when operating your Spektrum transmitter.

IC INFORMATION

IC Number: 6157A-ECX13002 This device complies with Industry Canada license-exempt RSS standard(s). Operation is subject to the following two conditions:

(1) this device may not cause interference, and (2) this device must accept any interference, including interference that may cause undesired operation of the device.

EU Compliance Statement: Horizon Hobby, LLC hereby declares that this product is in compliance with the essential requirements and other relevant provisions of the R&TTE, EMC, and LVD

Directives.

A copy of the EU Declaration of Conformity is available online at: http://www.horizonhobby.com/content/support-render-compliance.

Instructions for disposal of WEEE by users in the European Union

This product must not be disposed of with other waste. Instead, it is the user’s responsibility to dispose of their waste equipment by handing it over to a designated collections point for the recycling of waste electrical and electronic equipment. The separate collection and recycling of your waste equipment at the time of disposal will help to conserve natural resources and ensure that it is recycled in a manner that protects human health and the environment. For more information about where you can drop off your waste equipment for recycling, please contact your local city office, your household waste disposal service or where you purchased the product.

1.9 4WD ELECTRIC SCALE CRAWLER RTR

11

ECX211014

ECX211015

ECX211016

ECX211017

ECX211018

ECX211019

ECX211020

ECX211021

ECX212009

ECX212010

Replacement Parts / Ersatzteile / Pièces de rechange / Pezzi di ricambio

Part #

DYNS1209

DYNS2210

ECX1015

ECX13002

ECX13003

Description

Tazer 370 motor

Beschreibung

Motor: Tazer 370

WP 60A Bürstenregler

Vorwärts/rückwärts

WP 60A FWD/REV Brushed

ESC

5x10x4mm Ball Bearing (8) Kugellager 5x10x4mm (8)

2.4GHz Surface TX, 2-CH, V3 2.4GHz 2 Kanal Sender V3

2.4GHz RX Waterproof,

2-Channel V3

2.4GHz 2 Kanal Empfänger wasserfesten V3

Description

Moteur: Tazer 370

WP 60A Contrôleur à balais avant/ arrière

Roulements 5x10x4mm (8)

2.4GHz Emetteur 2 voies, V3

2.4GHz Récepteur étanche 2 voies

V3

Descrizione

Motore: Tazer 370

WP 60A ESC con spazzole avanti/ indietro

Cuscinetto a sfere 5x10x4mm (8)

2-Ch trasmettitore, V3

2.4GHz ricevitore impermeabile

2Ch, V3

ECX210011

ECX211009

ECX212012

ECX212018

ECX212019

ECX212020

ECX212021

ECX212022

ECX212023

ECX212024

ECX212025

ECX212026

ECX212027

ECX212028

ECX213002

ECX214010

ECX214011

1.9 Barrage Carrosserie peinte Carrozzeria, verniciata: 1.9 Barrage

Servo Mount: 1/18 4WD

Temper

Front/Rear Bumper Set: 1.9

Barrage

Servohalter: 1/18 4WD

Temper

Stoßfänger Vorne/Hinten: 1.9

Barrage

1/18 4WD Temper: Support de servo Supporto servo: 1/18 4WD Temper

1.9 Barrage: Set de pare-choc Av/Arr Set paraurti ant/post: 1.9 Barrage

Bumper Mount: 1.9 Barrage Stoßfängerhalter: 1.9 Barrage 1.9 Barrage: Support de pare-choc Supporto paraurti: 1.9 Barrage

Chassis Set: 1.9 Barrage Chassis: 1.9 Barrage 1.9 Barrage: Châssis Set telaio: 1.9 Barrage

Skid Plate: 1.9 Barrage

Shock Tower: 1.9 Barrage

Unterfahrschutz: 1.9 Barrage

Dämpferbrücke: 1.9 Barrage

1.9 Barrage: Plaques de protection

1.9 Barrage: Support d’amortisseurs

Piastra di protezione: 1.9 Barrage

Torre ammortizz.: 1.9 Barrage

Body Post: 1.9 Barrage Karosseriehalter: 1.9 Barrage 1.9 Barrage: Supports de carrosserie Supporti carrozzeria: 1.9 Barrage

Chassis Brace (2): 1.9 Barrage Chassishalter (2): 1.9 Barrage 1.9 Barrage: Renforts de châssis (2) Rinforzo telaio (2): 1.9 Barrage

ESC & Battery Tray: 1.9

Barrage

Regler und akkuhalter: 1.9

Barrage

1.9 Barrage: Support de batterie et contrôleur

Spool 38T: 1/18 4WD Temper Spool 38T: 1/18 4WD Temper 1/18 4WD Temper: Spool 38T

Supporto batteria e ESC: 1.9

Barrage

Corona 38T: 1/18 4WD Temper

Axle Pinion Gear 14T: 1/18

4WD Temper

Transmission Assembled: 1/18

4WD Temper

Spur Gear 48P 60T(1): 1/18

4WD Temper

Pinion Gear, 48P 16T: 1.9

Barrage

Transmission Outdrive: 1.9

Barrage

Driveshaft (2): 1.9 Barrage

Rear Hub (2): 1.9 Barrage

Rear Axle (2): 1.9 Barrage

Ritzel 14T: 1/18 4WD Temper

Abtrieb montiert: 1/18 4WD

Temper

Hauptzahnrad 48P 60T(1): 1/18

4WD Temper

Ritzel, 48P 16T: 1.9 Barrage

Anriebsklauen: 1.9 Barrage

Radträger Hinten (2): 1.9

Barrage

Radachse hinten (2): 1.9

Barrage

1/18 4WD Temper: Pignon 14T

1/18 4WD Temper: Transmission assembleés

1/18 4WD Temper: Couronne 48P

60T(1)

1.9 Barrage: Pignon, 48P 16T

1.9 Barrage: Noix de sortie de transmission

Antriebswelle (2): 1.9 Barrage 1.9 Barrage: Cardan (2)

1.9 Barrage: Fusée arrière (2)

1.9 Barrage: Axe de roue arrière (2)

Pignone 14T: 1/18 4WD Temper

Trasmissione montati: 1/18 4WD

Temper

Corona 48P 60T(1): 1/18 4WD

Temper

Pignone, 48P 16T: 1.9 Barrage

Bicchierini transmissione: 1.9

Barrage

Albero trasmissione (2): 1.9 Barrage

Mozzo posteriore (2): 1.9 Barrage

Front CV Shaft, Set (2): 1.9

Barrage

Front/Rear Diff Case V2: 1.9

Barrage

Steering Spindle V2: 1.9

Barrage

Front/Rear Hub Set, V2: 1.9

Barrage

CV Wellen Set Vorne (2): 1.9

Barrage

Diffgehäuse Vorne/Hinten V2:

1.9 Barrage

Lenkspindel V2: 1.9 Barrage

1.9 Barrage: Hexagone 12mm, large

1.9 Barrage: Set de cardans CVD avant (2)

1.9 Barrage: Boitiers de différentiel

Av/Arr V2

1.9 Barrage: Set de fusées V2

1.9 Barrage: Set d’étriers Av/Arr, V2

Mozzi ruota posteriori (2): 1.9

Barrage

Trascinatore 12 mm, largo: 1.9

Barrage

Set alberi CV anteriore (2): 1.9

Barrage

Scatola diffeenziale ant/post V2:

1.9 Barrage

Fusello sterzo V2: 1.9 Barrage

Set hub ant/post, V2: 1.9 Barrage

F/R Shocks Assembled (2): 1.9

Barrage

Molded Link (2): 1/18 4WD

Temper

Träger Set Vorne/Hinten, V2:

1.9 Barrage

Dämpfer montiert Vorne/

Hinten (2): 1.9 Barrage

Anlenkungen welle (2): 1/18

4WD Temper

Servo Linkage (2): 1.9 Barrage Servoarm (2): 1.9 Barrage

1.9 Barrage: Amortisseurs Av/Arr assemblés (2)

Biellette moulé (2): 1/18 4WD

Temper

1.9 Barrage - Biellette (2)

Ammortizzatori montati ant/post

(2): 1.9 Barrage

Collegamento stampato (2): 1/18

4WD Temper

Collegamento servo (2): 1.9

Barrage

40

Replacement Parts / Ersatzteile / Pièces de rechange / Pezzi di ricambio

Part # Description Beschreibung Description

ECX214012

ECX214013

ECX217001

Lower Link (2): 1.9 Barrage

Upper Link (2): 1.9 Barrage

Unterlenker (2): 1.9 Barrage

Oberlenker (2): 1.9 Barrage

1.9 Barrage: Tirant inférieur (2)

1.9 Barrage: Tirant supérieur (2)

1/18 4WD - Set de roulements de fusées

Descrizione

Collegamento inferiore (2): 1.9

Barrage

Collegamento superiore (2): 1.9

Barrage

Set supporto fusello/hub: 1/18

4WD All

ECX41004

ECX41006

SPMS602

Spindle/Hub Bearing Set: 1/18

4WD All

1.9 Wheel Black (2): 1.9

Barrage

1.9 Falken Wildpeak AT3 W

Tire (2)

SCT2 Digital Servo

ECX Spindelset/Lagerset:

1/18 4WD All

1.9 radkranz schwarz (2): 1.9

Barrage

Reifen 1.9 Falken Wildpeak

AT3 W (2)

SCT2 Digital Servo

1.9 Barrage - Jante 1,9 noire (2)

Servo digital SCT2

Ruota (2) 1.9 nera: 1.9 Barrage

SCT2 Digital Servo

Optional Parts / Optionale Teile / Liste des options / Elenco parti opzionali

Part #

DYN1471

Description

7.2V 1750mAh NiMH 6C Flat

Battery, EC3: Minis

Beschreibung

Flache Akkus Ni-MH 7,2V

1750mA, EC3: Mini 1/18

DYN1473

DYNC2000CA Prophet Sport NiMH 35W AC

Charger

ECX210010

7.2V 1200mAh Ni-MH Battery,

Long w/EC3: Minis

Body Set, Clear: 1.9 Barrage

Lange Akkus Ni-MH 7,2V

1750mA, EC3: Mini 1/18

Prophet Sport NiMH 35W

AC-Ladegerät

Body Set, transparent: 1.9

Barrage

ECX312005

ECX41005

Rear Hub Carrier, Alum: 1.9

Barrage

1.9 Wheel (2) White: 1.9

Barrage

Rädträger hinten, Alum: 1.9

Barrage

1.9 radkranz weiß (2): 1.9

Barrage

Description

Mini 1/18: Batterie plate Ni-MH

7,2V 1750mA, prise EC3

Mini 1/18: Batterie longue Ni-MH

7,2V 1200mA, prise EC3

Chargeur Prophet Sport AC Ni-MH

35W

1.9 Barrage: Carrosserie, transparente

1.9 Barrage: Set d’étriers arrière, aluminium

1.9 Barrage: Jante 1,9 blanche (2)

Descrizione

Batteria piatta 6C NiMH 1750 mAh 7,2 V, EC3: Minis

Batteria lunga NiMH 1200 mAh

7,2 V c/EC3: Minis

Caricabatteria AC Prophet Sport

NiMH 35 W

Carrozzeria trasparente: 1.9

Barriage

Supporto hub posteriore, allum.:

1.9 Barrage

Ruota (2) 1.9 bianca: 1.9 Barrage

ECX1048

ECX210011 - Painted / Painted / peinte / verniciata

ECX210010 - Clear / transparent / transparente / trasparente

ECX1048

ECX1048

ECX1048

ECX213002

ECX41006

ECX41004

ECX1060

1.9 4WD ELECTRIC SCALE CRAWLER RTR

41

PARTS DIAGRAM | EXPLOSIONSZEICHNUNG | VUE ÉCLATÉE DES PIÈCES |

ESPLOSO DEL MODELLO CON REFERENZA PEZZI

42

PARTS DIAGRAM | EXPLOSIONSZEICHNUNG | VUE ÉCLATÉE DES PIÈCES |

ESPLOSO DEL MODELLO CON REFERENZA PEZZI

FRONT AXLE | VORDERACHSE | HINTERACHSE | ASSE ANTERIORE

ECX211009

ECX216003

ECX216003

ECX212020

ECX212026

ECX217001

ECX216003

ECX214010

ECX212010

ECX217001

ECX217001

ECX212026

ECX212025

ECX212009

ECX216003

ECX216003

ECX217001

ECX214011

ECX216003

ECX216003

ECX216003

ECX212028

ECX217001

ECX216003

ECX212027

ECX212027

ECX217001

ECX212024

ECX212027

ECX216003

ECX212024

REAR AXLE | ESSIEU AVANT | ESSIEU ARRIÈRE | ASSE POSTERIORE

ECX212026

ECX216003

ECX212009

ECX212026

ECX217001

ECX212020

ECX212010

ECX217001

ECX212023

ECX212020

ECX217001

ECX217001

ECX216003

ECX312005

ECX212024

ECX216003

ECX217001

ECX212024

1.9 4WD ELECTRIC SCALE CRAWLER RTR

43

®

ECX01009 | ECX01009I www.ecxrc.com

© 2017 Horizon Hobby, LLC. ECX, the ECX logo, Barrage, Dynamite, Speedpack, Prophet, Tazer, EC3, and the Horizon Hobby logo are trademarks or registered trademarks of Horizon Hobby, LLC.

The Spektrum trademark is used with permission of Bachmann Industries, Inc. Patents Pending.

Updated 04/2017 52321.2