GIL150operate manual.cdr

GIL-150
Banknote Fitness Sor ter
* The update of this manual may not be simultaneous with the product.
All features should be referred to the actual product
PREFACE
Thank you for using Banknote Fitness Sorter. By adapting the technology
of CIS, UV, MG and IR, GIL-150 can perfectly do value-counting, counterfeit
-detection and fitness -sorting .
Overview of main functions
*
*
*
*
*
Fitness Sorting
Version Sorting / Orientation & Direction Sorting / Denomination Sorting;
Value-Counting / Piece-Counting / Mix-Counting / Counterfeit-Detecting;
(Pre-set) Batch-Counting;
Series Number (Optional)
Before using the unit, Please carefully read this manual
2
CONTENT
PREFACE
OPERATION GUIDANCE
Overview of control display----10
POINTS FOR ATTENTION
Norms of safety operation --------1
Icon Description--------------------12
Requirements of placing banknotes --2
Function operations- --- ------14
TROUBLESHOOTING
Daily check-up ---------------3
Ttroubleshooting -----------20
APPEARANCE and PARAMETERS
Error Code- - - - - - - - - - - - - ----21
Overview of Front part ----- -----4
Overview of Rear part ----- ------5
Feeding Part Description ---------6
Technical Specification ----------7
MAINTENANCE
Instructions of maintenance---22
PACKING LIST
Packing list --------------23
Parameter Set-up -------------8
POINTS for ATTENTION
Nor ms of Safety Operation
DO NO T place the product near heat sources, such as stove or heater
DO NOT use the product in the damp or dusty environment.
DO NOT try to dissassemble or repair the product by yourself, which may cause accidents.
DO NOT place heavy objects or liquid containers, such as a beverage can, on the product.
DO NOT try to open or operate the product by force.
DO NOT unplug the product holding its electric cord, such action may cause electric shock or fire.
Make sure to apply proper grounding, using the plug. Short-circuit may cause electric shock.
Make sure to shut power off before putting your hands inside the product for such purposes
as replacing a fuse or checking the components.
In order to avoid the electric shot, please
be sure the machine is perfectly connected to
the power.Before maintain or open the machine,
please be sure the power is off and the plug is
disconnected.
1
1
POINTS of ATTENTION
Requirement of Place Banknotes
DO NOT insert banknotes, which are severely damaged, wet or mixed with alien substances
Make sure that no other objects enter into the product, including your hands and hairs, when inserting
and counting banknotes.
Straighten the folds or corners of banknotes before insertion.
Banknotes should be properly arranged and put on the hopper as shown below.
figure 2
figure 1
2
2
POINTS
of ATTENTION
注意事项
Daily check up
Remember to switch off the power and unplug the produce prior to the checkup
Do not use chemicals to clean machine and inside sensors. some chemical will corrode
machine. Instead, it is recommended to use the brush to clean and remove any alien objects
Do not press the LCD with a sharp object, such as pen or pin.
Monthly check the condition of power cable as follows:
If there are any cracks on the cable
If the power cable is connected to the plug perfectly
figure 3
3
APPEARANCE and PARAMETERS
Over view of Front Par t
figure 4
Upper Compartment Cover
Touch Screen
Guide shaft
Reject Pocket
Front cover
11
Stacker
4
APPEARANCE and PARAMETERS
Over view of Rear Par t
figure 5
Lower Compartment Cover
AC Power Input
110V/220V
Print port
Power switch
5
APPEARANCE and PARAMETERS
Feeding Par t Description
Before work the machine, Please adjust the interval of feeding part till a proper thickness.
figure 6
Note:
The interval should be equal to the thickness
of one piece of banknote, so as to ensure the
machine can feed banknotes smoothly.
Otherwise, inadequate interval will bring
about skew banknotes or double banknotes,
feed into the machine. It is recommended that
only professional people is allowed to adjust.
Note:
The qualify of banknote-feeding is a
critically important to the product
performance
6
8
APPEARANCE
and PARAMETERS
注意事项
Technical specification
Banknote Sizes:100*50-190*90mm
Currency: Any currency
Counting Display:Touch Screen
Feed system:Roller Friction
Counting Speed:600/800/1000/1200 pcs/min
Interface: LAN,USB,RS-232
Power Consumption:150W
Sorting Speed: 600/800pcs/min
Net Weight:13kg
Series number speed:400/600pcs/min
Power Supply:220V/50Hz;110V/60Hz
Hopper Capacity: 500 notes
Stacker Capacity: 200 notes
Dimension(W*D*H):324*288*390mm
Reject Pocket Capacity: 100 notes
Reject Capacity:100notes
7
OPERATION GUIDANCE
Over view of control display
The function of virtual and operation keyboard are same
figure 9
Au t o
Curreny
Mi x
5
Mix
1.CF Function (Counterfeit Detection) CF
6
Report
Denom
CF
Count
2.ADD Function (Cumulative Counting) Add
3. Capacity of Reject Pocket setup (eg: 200)
Function
1 2
CF
ADD
3
4
69 B
32 S
4. Count Speed setup (eg: 800)
5. Auto/Manual mode setup Press START/STOP
Clear
button under the manual mode
6.Operating mode
START/STOP
button also has the function of clear the number or stop/start the machine during counting
10
OPERATION GUIDANCE
Menu
figure 10
Auto
Curreny
figure 11
Mix
5
7
Mix
6
P a s s wo r d s
8
Report
Denom
CF
Count
Function
1 2
CF
ADD
3
69 B
4
4
1
4
7
Clear
32 S
(The Openning Interface)
11
3
6
9
0
Press and Hold “START/STOP”
When the product is power-on, the openning
interface will be displayed as above. Press the
virtual button or the button aside to start operation
NOTE:
In order to avoid permanent damge on the
LCD, please do NOT use any sharp object
to do theoperation
2
5
8
4
APPEARANCE and PARAMETERS
Parameter Set-up
Set UP
Press and Hold START/STOP”
Type in PIN Code: 7890
Enter the interface of parameter set-up, as shown in Figure 7 & 8
figure 7
Pass words
1
1
4
7
ST A R T / S T O P
2
5
8
3
6
9
0
(Virtual Display)
8
APPEARANCE and PARAMETERS
Parameter Set-up
figure 8
Note:
Please change the parameter under
the guidance of professional people
MG
005
UV
005
IR
005
MT
005
SPEED
800
Note:
Setup:Click on the
parameterthat need to adjust,
and type in the value,
as shown in figure 11.
Definitions of Parameters
ATM:New/Old banknote sorting. (Factory setup is 5) The higher value, The more old banknotes will be sorted out
MG:Magnetism sensitivity. (Factory setup is 5) The higher value, The more sensitive MG will be.
UV:Ultra-Violat sensitivity. (Factory setup is 5) The higher value,The more sensitive UV will be.
IR:Infra-Red sensitivity. (Factory setup is 5) The higher value, The more sensitive IR will be.
MT:Magnetism thread. (Factory setup is 5) The higher value, The more sensitive MT will be.
Speed: Counting speed (Four options: 400/600/800/1200 pcs/min)
9
OPERATION GUIDANCE
Icon Description
Curren
Select the currency to work on
Report
Print out the result of one counting/operation.
C F
Switch ON/OFF the function of countfeit detection (UV/IR/MG/MT/3D/IMG).
Function
Batch
The batch unit for counting.
ADD
Switch ON/OFF accumulative count
AUTO
S/N
Switch automatic or manual counting
Switch ON/OFF Series Number Mode(Optional)
SORT
M - Face
Multi-banknotes face side sorting mode
M-Orient
Multi-banknotes orient side sorting mode
S-Face
Single-banknotes face side sorting mode
S-Orient
Single-banknotes orient side sorting mode
S-Version
Banknote version sorting mode
S-Denom
Switch ON/OFF Denomination Sorting Mode
12
OPERATION GUIDANCE
Icon Description
Fit
SAM
MIX
Switch ON/OFF fitness(New/Old)-sorting mode (Optional)
Password setup
Switch ON/OFF mix counting mode
Denom
Sort out the denomination which is determined
Count
Switch ON/OFF piece counting mode
Clear
13
FUNCTION OPERATIONS
MIX
Mix mode:Shows total amount and number of banknotes when mixed
denominations are counted together
Mix
Press The Button Enter Mix Function
Before banknotes are placed on the hopper, it is possible:
Aut/Man
To change automatic or manual counting
Add
To switch on/off accumulative count
CF
To s w i c h o n / o f f c o u n t f e i t f u n c t i o n
Batch
To print the result of the counting
Finish counting
To check the cause of rejection, by press R J , as shown in Figure 12
Shows total amount and number of banknotes by press print
15
14
FUNCTION OPERATIONS
RJ And Repor t
By press Rport To check the counting results, as shown in figure 12, such information as
counted denomination, the number of pieces, total value and rejected piece number
By press R J to check the cause of rejection, as shown in figure 13
(Please refer to the code definition in P23)
figure 12
1
2
5
10
20
50
100
Staker
*
*
*
*
*
*
*
0
figure 13
1
2
3
4
0
0
0
0
0
0
0
RJ 0
Total
E0
E0
E0
E0
U
U
U
U
M
M
M
M
W
W
W
W
Mt
Mt
Mt
Mt
T2
T2
T2
T2
Ir
Ir
Ir
Ir
W _ Ir _ N
W _ Ir _ N
W _ Ir _ N
W _ Ir _ N
0
Due to the cause of double or chain, the number of rejected notes may not be as same
as the number shown on the screen. Please re-count the rejected banknotes
15
FUNCTION OPERATIONS
COUNT
COUNT
Count mode: Counts the total number of banknotes without recognition of denomination
Press The Button Enter Count mode
Before banknotes are placed on the hopper, it is possible:
Aut/Man
To change automatic or manual counting
Add
To switch on/off accumulative count
CF
To s w i c h o n / o f f c o u n t f e i t f u n c t i o n
Batch
To print the result of the counting
Finish counting
To check the cause of rejection, by press R J
Shows total amount and number of banknotes by press print
15
16
FUNCTION OPERATIONS
Denomination sor ting
Deno
Denomination sorting mode : Sort out the denomination banknote, which is
initially counted
Press The Button Enter Denomination soring
Before banknotes are placed on the hopper, it is possible:
Aut/Man
To change automatic or manual counting
Add
To switch on/off accumulative count
CF
To s w i c h o n / o f f c o u n t f e i t f u n c t i o n
Batch
To print the result of the counting
Finish counting
To check the cause of rejection, by press R J
Shows total amount and number of banknotes by press print
17
15
FUNCTION OPERATIONS
FIT (optional)
Fit
Fitness sorting mode : Sort out New and Old banknotes separately, by IMAGE only.
Press The Button Enter Fit Function
Before banknotes are placed on the hopper, it is possible:
Aut/Man
To change automatic or manual counting
Add
To switch on/off accumulative count
CF
To s w i c h o n / o f f c o u n t f e i t f u n c t i o n
Batch
To print the result of the counting
Finish counting
To check the cause of rejection, by press R J
Shows total amount and number of banknotes by press print
15
18
19
FUNCTION OPERATIONS
Version sor ting
S_Ver
Version sor ting mode: Sort out different version banknote separately, which is
initially counted
Press The Button Enter Version sorting
Before banknotes are placed on the hopper, it is possible:
Aut/Man
To change automatic or manual counting
Add
To switch on/off accumulative count
CF
To s w i c h o n / o f f c o u n t f e i t f u n c t i o n
Batch
To print the result of the counting
Finish counting
To check the cause of rejection, by press R J
Shows total amount and number of banknotes by press print
18
FUNCTION OPERATIONS
Orient sor ting
Orient
Orient sor ting mode: Sort out different side (front/back) or direction(left/right)
banknotes separately, which is initially counted.
Press The Button Enter Orient soring
Before banknotes are placed on the hopper, it is possible:
Aut/Man
To change automatic or manual counting
Add
To switch on/off accumulative count
CF
To s w i c h o n / o f f c o u n t f e i t f u n c t i o n
Batch
To print the result of the counting
Finish counting
To check the cause of rejection, by press R J
Shows total amount and number of banknotes by press print
19
TROUBLESHOOTING
Troubleshooting
If banknote is congested inside of the mahine during counting, the congest location will
be indicated as shown in below figure
figure 14
1
2
5
4
3
6
Congestion in point 1&2, do as folows
Open the upper compartment cover,
take out the banknote, and close gently
The sparkling point is the congest location:
1.The entry banknote-feeding part (see figure …)
2.Open the upper compartment cover, to find the banknote
3.Open the lower compartment cover, to find the banknote (see figure….)
4.Open the machine from the front, to find the banknote (See figure…)
5.Banknotes on the reject pocket
6.Banknotes on the staker pocket
Congestion in point 3, do as follows
Open the lower compartment cover,
take out the banknote, and close gently;
or Open the front cover as the congestion
in point 4&5, manually clockwise-turning
the wheel on the right-hand, the jammed
banknotes is possible to be moved out
Congestion in point 4 & 5 , do as follows
Open the front cover by press the
trimmer(RJ Pocket), and the other hand
lift the display part. Take out the
banknotes, and close gently.
20
Er ror Code
Code definition
C o d e D e s cr ip ti on
R em a rk s
Co de De sc ri pt ion
U
UV detection error
E1
Error left side reading notes image
M
MG detection error
E2
Error right side reading notes image
m
MG detection error
E3
Error up side reading notes image
W
Error banknotes too large
E4
Error low side reading notes image
D
Error banknotes double
E5
Error of size
Mt
Mt detection error
E6
Tilt is too large
IR
infrared detection error
E7
Out of bounds left border
De
double detection error
E8
refused to
W_
watermark detection error
E9
Error of width
IR_
infrared detection error
E10
Error of height
N
Too Old
E11
Error of top left corner
E12
Error of top right corner
E13
washed banknotes
E14
Error notes for holes or bends
E15
IR
21
counterfeit
R em a r k s
MAINTENANCE
Instructions of maintenance
Image sensor
Open the upper compartment, clean the sensor with brush or soft cloth. Close gently after cleanning.
MG sensor
Open the machine from the front, clean the sensor with brush or soft cloth. Close gently after cleanning
Thoroughfare
Clean the stacker and the pocket with brush or soft cloth.
Reject/Stacker Pocket
Clean the stacker and the pocket with brush or soft cloth.
NOTE:
The maintenance should be done
once a week
22
Packing List
Packing List
name
number
Operation manual
1
Power cable
1
QA
1
Brush
1
USB
1
23
Option
Download PDF
Similar pages