Safety and Reference - CNET Content Solutions

OWNER’S MANUAL
Safety and Reference
LED TV*
*LG LED TV applies LCD screen with LED backlights.
Please read this manual carefully before operating your set and
retain it for future reference.
www.lg.com
Safety instructions
Please read these safety precautions carefully before
using the product.
ENGLISH
WARNING
Make sure to connect Mains cable to compliant AC mains socket with
Grounded earth pin. (Except for devices which are not grounded on
earth.) Otherwise possibility you may be electrocuted or injured.
Do not place the TV and/or remote control in the following
environments:
• A location exposed to direct sunlight
• An area with high humidity such as a bathroom
• Near any heat source such as stoves and other devices that
produce heat
• Near kitchen counters or humidifiers where they can easily be
exposed to steam or oil
• An area exposed to rain or wind
• Near containers of water such as vases
Otherwise, this may result in fire, electric shock, malfunction or product
deformation.
Do not place the product where it might be exposed to dust. This may
cause a fire hazard.
Mains Plug is the TV connecting/disconnecting device to AC mains
electric supply. This plug must remain readily attached and operable
when TV is in use.
Do not touch the power plug with wet hands. Additionally, if the cord
pin is wet or covered with dust, dry the power plug completely or wipe
dust off. You may be electrocuted due to excess moisture.
Insert power cable plug completely into wall socket otherwise if not
secured completely into socket, fire ignition may break out.
Ensure the power cord does not come into contact with hot objects
such as a heater. This may cause a fire or an electric shock hazard.
Do not place a heavy object, or the product itself, on power cables.
Otherwise, this may result in fire or electric shock.
Bend antenna cable between inside and outside building to prevent
rain from flowing in. This may cause water damaged inside the Product
and could give an electric shock.
When mounting TV onto wall make sure to neatly install and isolate
cabling from rear of TV as to not create possibility of electric shock /
fire hazard.
Do not plug too many electrical devices into a single multiple electrical
outlet. Otherwise, this may result in fire due to over-heating.
2
Des
ENGLISH
Do not drop the product or let it fall over when connecting external
devices. Otherwise, this may result in injury or damage to the product.
Do not drop metallic objects such as coins, hair pins, chopsticks or wire
into the product, or inflammable objects such as paper and matches.
Children must pay particular attention. Electrical shock, fire or injury
can occur. If a foreign object is dropped into the product, unplug the
power cord and contact the service centre.
icca
nt
Keep the anti-moisture packing material or vinyl packing out of the
reach of children. Anti-moisture material is harmful if swallowed. If
swallowed by mistake, force the patient to vomit and visit the nearest
hospital. Additionally, vinyl packing can cause suffocation. Keep it out
of the reach of children.
Do not let your children climb or cling onto the TV.
Otherwise, the TV may fall over, which may cause serious injury.
Dispose of used batteries carefully to ensure that a small child does not
consume them. Please seek Doctor- Medical Attention immediately if
child consumes batteries.
Do not insert any metal objects/conductors (like a metal chopstick/
cutlery/screwdriver) between power cable plug and input Wall Socket
while it is connected to the input terminal on the wall. Additionally,
do not touch the power cable right after plugging into the wall input
terminal. You may be electrocuted. (Depending on model)
Do not put or store inflammable substances near the product. There is a
danger of combustion/explosion or fire due to careless handling of the
inflammable substances.
Do not spray water on the product or scrub with an inflammable
substance (thinner or benzene). Fire or electric shock accident can
occur.
Do not allow any impact, shock or any objects to fall into the unit,
and do not drop anything onto the screen. You may be injured or the
product can be damaged.
Never touch this product or antenna during a thunder or lighting storm.
You may be electrocuted.
Never touch the wall outlet when there is leakage of gas, open the
windows and ventilate. It may cause a fire or a burn by a spark.
Do not disassemble, repair or modify the product at your own
discretion. Fire or electric shock accident can occur.
Contact the service centre for check, calibration or repair.
3
CAUTION
ENGLISH
If any of the following occur, unplug the product immediately and
contact your local service centre.
• The product has been impacted by shock
• The product has been damaged
• Foreign objects have entered the product
• The product produced smoke or a strange smell
This may result in fire or electric shock.
Unplug the TV from AC mains wall socket if you do not intend to use the
TV for a long period of time. Accumulated dust can cause fire hazard
and insulation deterioration can cause electric leakage/shock/fire.
Install the product where no radio wave occurs.
There should be enough distance between an outside antenna and
power lines to keep the former from touching the latter even when the
antenna falls. This may cause an electric shock.
Do not install the product on places such as unstable shelves or inclined
surfaces. Also avoid places where there is vibration or where the
product cannot be fully supported. Otherwise, the product may fall or
flip over, which may cause injury or damage to the product.
Apparatus shall not be exposed to dripping or splashing and no objects
filled with liquids, such as vases, shall be placed on the apparatus.
Do not install this product on a wall if it could be exposed to oil or oil
mist. This may damage the product and cause it to fall.
If water enters or comes into contact with TV, AC adapter or power
cord please disconnect the power cord and contact service centre
immediately. Otherwise, this may result in electric shock or fire.
If you install the TV on a stand, you need to take actions to prevent the
product from overturning. Otherwise, the product may fall over, which
may cause injury.
If you intend to mount the product to a wall, attach VESA standard
mounting interface (optional parts) to the back of the product. When
you install the set to use the wall mounting bracket (optional parts), fix
it carefully so as not to drop.
Only use the attachments / accessories specified by the manufacturer.
Only use an authorized AC adapter and power cord approved by
LG Electronics. Otherwise, this may result in fire, electric shock,
malfunction or product deformation.
When installing the antenna, consult with a qualified service
technician. If not installed by a qualified technician, this may create a
fire hazard or an electric shock hazard.
Never Disassemble the AC adapter or power cord. This may result in fire
or electric shock.
4
Do not turn the product On/Off by plugging-in or unplugging the power
plug to the wall outlet. (Do not use the power plug for switch.) It may
cause mechanical failure or could give an electric shock.
Only use the specified type of battery. This could cause damage to the
remote control.
Please follow the installation instructions below to prevent the product
from overheating.
Do not mix new batteries with old batteries. This may cause the
batteries to overheat and leak.
ENGLISH
We recommend that you maintain a distance of at least 2 to 7 times
the diagonal screen size when watching TV. If you watch TV for a long
period of time, this may cause blurred vision.
• The distance between the product and the wall should be more
than 10 cm.
• Do not install the product in a place with no ventilation (e.g., on a
bookshelf or in a cupboard).
• Do not install the product on a carpet or cushion.
• Make sure the air vent is not blocked by a tablecloth or curtain.
Otherwise, this may result in fire.
Batteries should not be exposed to excessive heat. For example, keep
away from direct Sunlight , open fireplace and electric heaters.
Do not place non-rechargeable batteries in charging device.
Make sure there are no objects between the remote control and its
sensor.
Signal from Remote Control can be interrupted due to external/internal
lighting eg Sunlight, fluorescent lighting. If this occurs turn off lighting
or darken viewing area.
When connecting external devices such as video game consoles, make
sure the connecting cables are long enough. Otherwise, the product
may fall over, which may cause injury or damage the product.
Take care not to touch the ventilation openings when watching the TV
for long periods as the ventilation openings may become hot. This does
not affect the operation or performance of the product.
Periodically examine the cord of your appliance, and if its appearance
indicates damage or deterioration, unplug it, discontinue use of the
appliance, and have the cord replaced with an exact replacement part
by an authorized servicer.
Prevent dust collecting on the power plug pins or outlet. This may cause
a fire hazard.
Protect the power cord from physical or mechanical abuse, such as
being twisted, kinked, pinched, closed in a door, or walked upon. Pay
particular attention to plugs, wall outlets, and the point where the cord
exits the appliance.
5
ENGLISH
Do not press strongly upon the panel with a hand or sharp object such
as nail, pencil or pen, or make a scratch on it, as it may cause damage
to screen.
Avoid touching the screen or holding your finger(s) against it for long
periods of time. Doing so may produce some temporary or permanent
distortion/damage to screen.
When cleaning the product and its components, unplug the power
first and wipe it with a soft cloth. Applying excessive force may cause
scratches or discolouration. Do not spray with water or wipe with a wet
cloth. Never use glass cleaner, car or industrial shiner, abrasives or wax,
benzene, alcohol etc., which can damage the product and its panel.
Otherwise, this may result in fire, electric shock or product damage
(deformation, corrosion or breakage).
As long as this unit is connected to the AC wall outlet, it is not
disconnected from the AC power source even if you turn off this unit
by SWITCH.
When unplugging the cable, grab the plug and unplug it, by pulling at
the plug.
Don’t pull at the cord to unplug the power cord from the power board,
as this could be hazardous.
When moving the product, make sure you turn the power off first. Then,
unplug the power cables, antenna cables and all connecting cables.
The TV set or power cord may be damaged, which may create a fire
hazard or cause electric shock.
6
When moving or unpacking the product, work in pairs because the
product is heavy. Otherwise, this may result in injury.
Contact the service centre once a year to clean the internal parts of the
product.
Accumulated dust can cause mechanical failure.
Refer all servicing to qualified service personnel. Servicing is required
when the apparatus has been damaged in any way, such as power
supply cord or plug is damaged, liquid has been spilled or objects have
fallen into the apparatus, the apparatus has been exposed to rain or
moisture, does not operate normally, or has been dropped.
If the product feels cold to the touch, there may be a small “flicker”
when it is turned on. This is normal, there is nothing wrong with
product.
The panel is a high technology display product with resolution of two
million to six million pixels. You may see tiny black dots and/or brightly
coloured dots (red, blue or green) at a size of 1 ppm on the panel. This
does not indicate a malfunction and does not affect the performance
and reliability of the product.
This phenomenon also occurs in third-party products and is not subject
to exchange or refund.
Viewing 3D imaging (Only 3D
models)
WARNING
Displaying a still image for a prolonged period of time may cause image
sticking. Avoid displaying a fixed image on the TV screen for a long
period of time.
Generated Sound
“Cracking” noise: A cracking noise that occurs when watching or turning
off the TV is generated by plastic thermal contraction due to temperature and humidity. This noise is common for products where thermal
deformation is required. Electrical circuit humming/panel buzzing:
A low level noise is generated from a high-speed switching circuit,
which supplies a large amount of current to operate a product. It varies
depending on the product.
This generated sound does not affect the performance and reliability
of the product.
Do not use high voltage electrical goods near the TV (e.g. electric
mosquito-swatter). This may result in product malfunction.
ENGLISH
You may find different brightness and color of the panel depending on
your viewing position(left/right/top/down).
This phenomenon occurs due to the characteristic of the panel. It is not
related with the product performance, and it is not malfunction.
Viewing environment
• Viewing Time
-- When watching 3D contents, take 5 - 15 minute breaks every
hour. Viewing 3D contents for a long period of time may cause
headache, dizziness, fatigue or eye strain.
Those that have a photosensitive seizure or
chronic illness
• Some users may experience a seizure or other abnormal symptoms
when they are exposed to a flashing light or particular pattern
from 3D contents.
• Do not watch 3D videos if you feel nausea, are pregnant and/ or
have a chronic illness such as epilepsy, cardiac disorder, or blood
pressure disease, etc.
• 3D Contents are not recommended to those who suffer from stereo
blindness or stereo anomaly. Double images or discomfort in
viewing may be experienced.
• If you have strabismus (cross-eyed), amblyopia (weak eyesight) or
astigmatism, you may have trouble sensing depth and easily feel
fatigue due to double images. It is advised to take frequent breaks
than the average adult.
• If your eyesight varies between your right and left eye, revise your
eyesight prior to watching 3D contents.
Symptoms which require discontinuation or
refraining from watching 3D contents
• Do not watch 3D contents when you feel fatigue from lack of sleep,
overwork or drinking.
• When these symptoms are experienced, stop using/watching 3D
contents and get enough rest until the symptom subsides.
-- Consult your doctor when the symptoms persist. Symptoms may
include headache, eyeball pain, dizziness, nausea, palpitation,
blurriness, discomfort, double image, visual inconvenience or
fatigue.
7
CAUTION
Viewing environment
ENGLISH
• Viewing Distance
-- Maintain a distance of at least twice the screen diagonal
length when watching 3D contents. If you feel discomfort in
viewing 3D contents, move further away from the TV.
Viewing age
• Infants/Children
-- Usage/ Viewing 3D contents for children under the age of 6 are
prohibited.
-- Children under the age of 10 may overreact and become overly
excited because their vision is in development (for example:
trying to touch the screen or trying to jump into it). Special
monitoring and extra attention is required for children watching
3D contents.
-- Children have greater binocular disparity of 3D presentations
than adults because the distance between the eyes is
shorter than that of adults. Therefore they will perceive more
stereoscopic depth compared to adults for the same 3D image.
• Teenagers
-- Teenagers under the age of 19 may react with sensitivity due
to stimulation from light in 3D contents. Advise them to refrain
from watching 3D contents for a long time when they are tired.
• Elderly
-- The elderly may perceive less 3D effect compared to the young.
Do not sit closer to the TV than the recommended distance.
Cautions when using the 3D glasses
• Make sure to use LG 3D glasses. Otherwise, you may not be able to
view 3D videos properly.
• Do not use 3D glasses instead of your normal glasses, sunglasses or
protective goggles.
• Using modified 3D glasses may cause eye strain or image
distortion.
• Do not keep your 3D glasses in extremely high or low
temperatures. It will cause deformation.
• The 3D glasses are fragile and are easily scratched. Always use a
soft, clean piece of cloth when wiping the lenses. Do not scratch
the lenses of the 3D glasses with sharp objects or clean/wipe them
with chemicals.
8
Preparing
NOTE
• If the TV is turned on for the first time after it was shipped from the
factory, initialization of the TV may take a few minutes.
• Image shown may differ from your TV.
• Your TV’s OSD (On Screen Display) may differ slightly from that
shown in this manual.
• The available menus and options may differ from the input source
or product model that you are using.
• New features may be added to this TV in the future.
• The TV can be placed in standby mode in order to reduce the power
consumption. And the TV should be turned off if it will not be
watched for some time, as this will reduce energy consumption.
• The energy consumed during use can be significantly reduced if the
level of brightness of the picture is reduced, and this will reduce
the overall running cost.
• The items supplied with your product may vary depending on the
model.
• Product specifications or contents of this manual may be changed
without prior notice due to upgrade of product functions.
• For an optimal connection, HDMI cables and USB devices should
have bezels less than 10 mm thick and 18 mm width. Use an
extension cable that supports USB 2.0 if the USB cable or USB
memory stick does not fit into your TV’s USB port.
B
B
A
A
*A <
= 10 mm
*B <
= 18 mm
• Use a certified cable with the HDMI logo attached.
• If you do not use a certified HDMI cable, the screen may not display
or a connection error may occur. (Recommended HDMI Cable Types)
- High-Speed HDMI®/TM Cable (3 m or less)
- High-Speed HDMI®/TM Cable with Ethernet (3 m or less)
CAUTION
• Do not use any unapproved items to ensure the safety and product
life span.
• Any damage or injuries caused by using unapproved items are not
covered by the warranty.
• Some models have a thin film attached on to the screen and this
must not be removed.
• When attaching the stand to the TV set, place the screen facing
down on a cushioned table or flat surface to protect the screen
from scratches.
• Make sure that the screws are inserted correctly and fastened
securely. (If they are not fastened securely enough, the TV may tilt
forward after being installed.) Do not use too much force and over
tighten the screws; otherwise screw may be damaged and not
tighten correctly.
Lifting and moving the TV
Separate purchase items can be changed or modified for quality
improvement without any notification. Contact your dealer to buy these
items. These devices only work with certain models.
The model name or design may be changed depending on the upgrade
of product functions, manufacturer’s circumstances or policies.
Please note the following advice to prevent the TV from being scratched
or damaged and for safe transportation regardless of its type and size.
(Depending on model)
AG-F***
Cinema 3D Glasses
AN-MR600
Magic Remote
ENGLISH
Separate purchase
• It is recommended to move the TV in the box or packing material
that the TV originally came in.
• Before moving or lifting the TV, disconnect the power cord and
all cables.
• When holding the TV, the screen should face away from you to
avoid damage.
LG Audio Device
Maintenance
• Hold the top and bottom of the TV frame firmly. Make sure not to
hold the transparent part, speaker, or speaker grill area.
Cleaning your TV
Clean your TV regularly to keep the best performance and to extend the
product lifespan.
• Make sure to turn the power off and disconnect the power cord and
all other cables first.
• When the TV is left unattended and unused for a long time,
disconnect the power cord from the wall outlet to prevent possible
damage from lightning or power surges.
Screen, frame, cabinet and stand
• When transporting a large TV, there should be at least 2 people.
• When transporting the TV by hand, hold the TV as shown in the
following illustration.
To remove dust or light dirt, wipe the surface with a dry, clean, and
soft cloth.
To remove major dirt, wipe the surface with a soft cloth dampened in
clean water or a diluted mild detergent. Then wipe immediately with
a dry cloth.
• Avoid touching the screen at all times, as this may result in damage
to the screen.
• Do not push, rub, or hit the screen surface with your fingernail or a
sharp object, as this may result in scratches and image distortions.
• Do not use any chemicals as this may damage the product.
• Do not spray liquid onto the surface. If water enters the TV, it may
result in fire, electric shock, or malfunction.
Power cord
Remove the accumulated dust or dirt on the power cord regularly.
• When transporting the TV, do not expose the TV to jolts or
excessive vibration.
• When transporting the TV, keep the TV upright, never turn the TV
on its side or tilt towards the left or right.
• Do not apply excessive pressure to cause flexing /bending of frame
chassis as it may damage screen.
• When handling the TV, be careful not to damage the protruding
joystick button.
CAUTION
• Avoid touching the screen at all times, as this may result in damage
to the screen.
• Do not move the TV by holding the cable holders, as the cable
holders may break, and injuries and damage to the TV may occur.
9
Using the joystick button
Adjusting the menu
(Image shown may differ from your TV.)
When the TV is turned on, press the joystick button one time. You can
adjust the Menu items moving the joystick button up, down, left or
right.
ENGLISH
You can simply operate the TV functions, pressing or moving the joystick
button up, down, left or right.
Joystick Button
Turns the power off.
Clears on-screen displays and returns to TV viewing.
Changes the input source.
Accesses the Quick Settings.
NOTE
Basic functions
When the TV is turned off, place your
finger on the joystick button and
press it once and release it.
When the TV is turned on, place
your finger on the joystick button
and press it once for a few seconds
Power Off
and release it. All running apps will
close, and any recording in progress
will stop.
If you place your finger over the
Volume
joystick button and move it left or
Control
right, you can adjust the volume level
you want.
If you place your finger over the
Programmes joystick button and move it up or
Control
down, you can scrolls through the
saved programmes you want.
Power On
• When your finger over the joystick button and push it to the up,
down, left or right, be careful not to press the joystick button. If you
press the joystick button first, you may not be able to adjust the
volume level and saved programmes.
Mounting on a table
(Image shown may differ from your TV.)
1 Lift and tilt the TV into its upright position on a table. • Leave a 10 cm (minimum) space from the wall for proper
ventilation.
10 cm
10 cm
10 cm
10 cm
10 cm
2 Connect the power cord to a wall outlet.
CAUTION
• Do not place the TV near or on sources of heat, as this may result in
fire or other damage.
10
Using the kensington security
system
(This feature is not available for all models.)
Attach an optional wall mount bracket at the rear of the TV carefully
and install the wall mount bracket on a solid wall perpendicular to
the floor. When you attach the TV to other building materials, please
contact qualified personnel. LG recommends that wall mounting be
performed by a qualified professional installer. We recommend the use
of LG’s wall mount bracket. LG’s wall mount bracket is easy to move with
cables connected. When you do not use LG’s wall mount bracket, please
use a wall mount bracket where the device is adequately secured to the
wall with enough space to allow connectivity to external devices. It is
advised to connect all the cables before installing fixed wall mounts.
ENGLISH
• Image shown may differ from your TV.
The Kensington security system connector is located at the rear of the
TV. For more information of installation and using, refer to the manual
provided with the Kensington security system or visit http://www.
kensington.com. Connect the Kensington security system cable between
the TV and a table.
Mounting on a wall
10 cm
10 cm
10 cm
Securing the TV to a wall
10 cm
(This feature is not available for all models.)
Make sure to use screws and wall mount bracket that meet the VESA
standard. Standard dimensions for the wall mount kits are described in
the following table.
Separate purchase (Wall mounting bracket)
1 Insert and tighten the eye-bolts, or TV brackets and bolts on the back
of the TV.
Model
• If there are bolts inserted at the eye-bolts position, remove the
bolts first.
2 Mount the wall brackets with the bolts to the wall.
Match the location of the wall bracket and the eye-bolts on the rear
of the TV.
VESA (mm) (A x B)
Standard screw
Number of screws
3 Connect the eye-bolts and wall brackets tightly with a sturdy rope.
Make sure to keep the rope horizontal with the flat surface.
CAUTION
49/55UX96**
300 x 300
M6
4
LSW350B
Wall mount bracket
MSW240
60UX96**
300 x 300
M6
4
LSW350B
A
B
• Make sure that children do not climb on or hang on the TV.
NOTE
• Use a platform or cabinet that is strong and large enough to
support the TV securely.
• Brackets, bolts and ropes are not provided. You can obtain
additional accessories from your local dealer.
11
CAUTION
ENGLISH
• Disconnect the power first, and then move or install the TV.
Otherwise electric shock may occur.
• Remove the stand before installing the TV on a wall mount by
performing the stand attachment in reverse.
• If you install the TV on a ceiling or slanted wall, it may fall and
result in severe injury. Use an authorised LG wall mount and
contact the local dealer or qualified personnel.
• Do not over tighten the screws as this may cause damage to the TV
and void your warranty.
• Use the screws and wall mounts that meet the VESA standard. Any
damages or injuries by misuse or using an improper accessory are
not covered by the warranty.
NOTE
• Use the screws that are listed on the VESA standard screw
specifications.
• The wall mount kit includes an installation manual and necessary
parts.
• The wall mount bracket is not provided. You can obtain additional
accessories from your local dealer.
• The length of screws may differ depending on the wall mount.
Make sure to use the proper length.
• For more information, refer to the manual supplied with the wall
mount.
Connections (notifications)
Connect various external devices to the TV and switch input modes to
select an external device. For more information of external device’s
connection, refer to the manual provided with each device.
Available external devices are: HD receivers, DVD players, VCRs, audio
systems, USB storage devices, PC, gaming devices, and other external
devices.
NOTE
• The external device connection may differ from the model.
• Connect external devices to the TV regardless of the order of the
TV port.
• If you record a TV program on a DVD recorder or VCR, make sure to
connect the TV signal input cable to the TV through a DVD recorder
or VCR. For more information of recording, refer to the manual
provided with the connected device.
• Refer to the external equipment’s manual for operating
instructions.
• If you connect a gaming device to the TV, use the cable supplied
with the gaming device.
• In PC mode, there may be noise associated with the resolution,
vertical pattern, contrast or brightness. If noise is present, change
the PC output to another resolution, change the refresh rate to
another rate or adjust the brightness and contrast on the PICTURE
menu until the picture is clear.
• In PC mode, some resolution settings may not work properly
depending on the graphics card.
• Only a USB storage device is recognizable.
• If ULTRA HD content is played on your PC, video or audio may
become disrupted intermittently depending on your PC’s
performance. (Depending on model)
Antenna connection
Connect the TV to a wall antenna socket with an RF cable (75 Ω).
• Use a signal splitter to use more than 2 TVs.
• If the image quality is poor, install a signal amplifier properly to
improve the image quality.
• If the image quality is poor with an antenna connected, try to
realign the antenna in the correct direction.
• An antenna cable and converter are not supplied.
• Supported DTV Audio: MPEG, Dolby Digital, Dolby Digital Plus,
HE-AAC
• For a location that is not supported with ULTRA HD broadcasting,
this TV cannot receive ULTRA HD broadcasts directly. (Depending
on model)
12
Satellite dish connection
Speaker output setup
(Only satellite models)
ENGLISH
Connect the TV to a satellite dish to a satellite socket with a satellite RF
cable (75 Ω).
Euro scart connection
(Depending on model)
Transmits the video and audio signals from an external device to the
TV set. Connect the external device and the TV set with the euro scart
cable.
Output Type
Current
input mode
Digital TV
Analogue TV, AV
HDMI
AV
(TV Out1)
Digital TV
Control port for Speaker out
UP
Analogue TV
DOWN
1 TV Out : Outputs Analogue TV or Digital TV signals.
• Any Euro scart cable used must be signal shielded.
• When watching digital TV in 3D imaging mode, only 2D out signals
can be output through the SCART cable. (Only 3D models)
+
-
GND
RIGHT
CI module connection
(Depending on model)
View the encrypted (pay) services in digital TV mode.
• Check if the CI module is inserted into the PCMCIA card slot in the
right direction. If the module is not inserted properly, this can
cause damage to the TV and the PCMCIA card slot.
• If the TV does not display any video and audio when CI+ CAM is
connected, please contact to the Terrestrial/Cable/Satellite Service
Operator.
USB connection
(Depending on model)
Some USB Hubs may not work. If a USB device connected through a USB
Hub is not detected, connect it directly to the USB port on the TV.
LEFT
GND
NOTE
• Do not connect your headphones or earphones to the port for
connecting an external speaker.
• Use only with the 3 Pole 3.5mm Stereo Jack.
Method of volume control port
* Cable Spec.
Each Up/ Down pin is pulled to 3.3V
with CPU GPIO.
GND / UP / Down
CPU detects transition from 3.3V
to GND level for volume control.
13
Network setup
Other connections
Wired network connection
ENGLISH
This TV can be connected to a Pro:Centric server via the LAN port. After
making the physical connection, the TV needs to be set up for network
communication.
Connect the LAN port of the Modem or Router from Pro:Centric server
to the LAN port on the TV.
AUX LAN
2
LAN
Connect your TV to external devices. For the best picture and audio
quality, connect the external device and the TV with the HDMI cable.
Some separate cable is not provided.
Picture HDMI ULTRA HD Deep
Colour
-- On : Support 4K @ 50/60 Hz (4:4:4, 4:2:2, 4:2:0)
-- Off : Support 4K @ 50/60 Hz (4:2:0)
If the device connected to Input Port also supports ULTRA HD Deep
Colour, your picture may be clearer. However, if the device doesn’t
support it, it may not work properly. In that case, connect the device
to a different HDMI port or change the TV’s HDMI ULTRA HD Deep
Colour setting to Off.
(This feature is available on certain models which are supported
ULTRA HD Deep Colour only.)
• Remote control
1
The descriptions in this manual are based on the buttons on the remote
control. Please read this manual carefully and use the TV correctly.
Pro:Centric Server
Broadband Modem
Router
CAUTION
Broadband Modem
Pro:Centric Server
1 Connect the LAN port of the Modem or Router to the LAN port
on the TV.
2 Connect the LAN port of the PC to the AUX LAN port on the TV.
CAUTION
• Do not connect a modular phone cable to the LAN port.
• Since there are various connection methods, please follow the
specifications of your telecommunication carrier or internet service
provider.
14
To replace batteries, open the battery cover, replace batteries (1.5
V AAA) matching the and ends to the label inside the
compartment, and close the battery cover. To remove the batteries,
perform the installation actions in reverse.
• Do not mix old and new batteries, as this may damage the remote
control.
• The remote control will not be included for all sales market.
Make sure to point the remote control toward the remote control sensor
on the TV.
(Depending on model)
D
B
A
ENGLISH
C
A
C
(POWER) Turns the TV on or off.
Adjusts the brightness of the screen to reduce
energy consumption.
Shows the previous history.
Changes the input source.
Selects Radio, TV and DTV programme.
Number buttons Enters numbers.
Accesses the saved programme list.
(Space) Opens an empty space on the screen keyboard.
Returns to the previously viewed programme.
B
Adjusts the volume level.
Accesses the Home menu.
Resizes an image.
Mutes all sounds.
Scrolls through the saved programmes.
Moves to the previous or next screen.
Shows programme guide.
Displays and removes hotel interactive menu.
Views the information of the current programme and screen.
Navigation buttons (up/down/left/right) Scrolls through menus
or options.
Selects menus or options and confirms your input.
Accesses the Quick Settings.
(
) Returns to the previous level.
Clears on-screen displays and returns to TV viewing.
D
Coloured buttons These access special functions in some menus.
(
: Red,
: Green,
: Yellow,
: Blue)
Teletext buttons (
/
) These buttons are used for
teletext.
Recalls your preferred subtitle in digital mode.
Control buttons (
) Controls the Premium
contents, SmartShare menus or the SIMPLINK compatible devices
(USB or SIMPLINK).
Used for viewing 3D video. (depending on model)
Selects the MHP TV menu source. (depending on model)
By Pressing AD button, audio descriptions function will be
enabled. (depending on model)
Sets the alarm function. (depending on model)
15
Licenses
ENGLISH
Supported licenses may differ by model. For more information about
licenses, visit www.lg.com.
Manufactured under license from Dolby Laboratories.
Dolby and the double-D symbol are trademarks of Dolby
Laboratories.
The terms HDMI and HDMI High-Definition Multimedia Interface,
and the HDMI logo are trademarks or registered trademarks of HDMI
Licensing LLC in the United States and other countries.
Open source software
notice information
To obtain the source code under GPL, LGPL, MPL, and other open source
licenses, that is contained in this product, please visit http:// opensource.
lge.com.
In addition to the source code, all referred license terms, warranty
disclaimers and copyright notices are available for download.
LG Electronics will also provide open source code to you on CD-ROM
for a charge covering the cost of performing such distribution (such
as the cost of media, shipping, and handling) upon email request to
opensource@lge.com. This offer is valid for three (3) years from the date
on which you purchased the product.
Troubleshooting
This DivX Certified® device has passed rigorous testing to ensure it
plays DivX® video.
To play purchased DivX movies, first register your device at vod.divx.
com. Find your registration code in the DivX VOD section of your
device setup menu.
DivX Certified® to play DivX® video up to HD 1080p, including
premium content.
DivX®, DivX Certified® and associated logos are trademarks of DivX,
LLC and are used under license.
Covered by one or more of the following U.S. patents :
7,295,673; 7,460,668; 7,515,710; 7,519,274.
For DTS patents, see http://patents.dts.com. Manufactured under
license from DTS Licensing Limited. DTS, DTS-HD, the Symbol, & DTS
or DTS-HD and the Symbol together are registered trademarks of
DTS, Inc. © DTS, Inc. All Rights Reserved.
The software version can be updated for improvement in performance.
Customer needs to ensure the compatibility of customer’s equipment
with LGE software. If needed, please consult with LGE and upload
revised software version according to the guidance provided by LGE.
Cannot control the TV with the remote control.
• Check the remote control sensor on the product and try again.
• Check if there is any obstacle between the product and the remote
control.
• Check if the batteries are still working and properly installed (
to , to ).
No image display and no sound is produced.
• Check if the product is turned on.
• Check if the power cord is connected to a wall outlet.
• Check if there is a problem in the wall outlet by connecting other
products.
The TV turns off suddenly.
• Check the power control settings. The power supply may be
interrupted.
• Check if the Automatic Standby (Depending on model) / Sleep
Timer / Timer Power Off is activated in the Timers settings.
• If there is no signal while the TV is on, the TV will turn off
automatically after 15 minutes of inactivity.
When connecting to the PC (HDMI), ‘No signal’ or ‘Invalid Format’ is
displayed.
• Turn the TV off/on using the remote control.
• Reconnect the HDMI cable.
• Restart the PC with the TV on.
16
Specifications
Wireless module specification
ENGLISH
• Because band channel used by the country could be different, the user can not change or adjust the operating frequency and this product is set
for the regional frequency table.
• This device should be installed and operated with minimum distance 20 cm between the device and your body. And this phrase is for the
general statement for consideration of user environment.
0197
Wireless module (LGSBW41) specification
Wireless LAN
Standard
Bluetooth
0197
IEEE 802.11a/b/g/n
2400 to 2483.5 MHz
5150 to 5250 MHz
5725 to 5850 MHz (for Non EU)
Frequency Range
Output Power (Max.)
802.11a: 13 dBm
802.11b: 15 dBm
802.11g: 14 dBm
802.11n - 2.4 GHz: 16 dBm
802.11n - 5 GHz: 16 dBm
Standard
Bluetooth Version 4.0
Frequency Range
2400 to 2483.5 MHz
Output Power (Max.)
CI Module (W x H x D)
Environment
condition
10 dBm or Lower
100.0 mm x 55.0 mm x 5.0 mm
Operating Temperature
0 °C to 40 °C
Operating Humidity
Less than 80 %
Storage Temperature
-20 °C to 60 °C
Storage Humidity
Less than 85 %
Digital TV
Analogue TV
Television system
DVB-T/T2*
DVB-C
DVB-S*/S2*
PAL/SECAM B/G/I/D/K,
SECAM L/L’
Programme coverage
VHF, UHF,
C-Band*, Ku-Band*
VHF: E2 to E12,
UHF : E21 to E69,
CATV: S1 to S20,
HYPER: S21 to S47
Maximum number of storable programmes
6,000
1,500
External antenna
impedance
75 Ω
* Only DVB-T2/C/S/S2 support models.
17
HDMI-PC supported Mode
HDMI-DTV supported Mode
ENGLISH
Resolution
Horizontal
Frequency (kHz)
Vertical Frequency
(Hz)
720 x 480
31.47
31.50
59.94
60.00
720 x 576
31.25
50.00
1280 x 720
44.96
45.00
37.50
59.94
60.00
50.00
28.12
33.72
33.75
26.97
27.00
33.71
33.75
56.25
67.43
67.50
53.95
54.00
56.25
61.43
67.50
112.50
135.00
135.00
53.95
54.00
56.25
61.43
67.50
112.50
135.00
135.00
50.00
59.94
60.00
23.97
24.00
29.97
30.00
50.00
59.94
60.00
23.98
24.00
25.00
29.97
30.00
50.00
59.94
60.00
23.98
24.00
25.00
29.97
30.00
50.00
59.94
60.00
1920 x 1080
3840 x 2160
1
4096 x 2160
1
1 : Only HDMI IN 1, HDMI IN 2 port
18
• PC audio is not supported
Resolution
Horizontal
Frequency (kHz)
Vertical Frequency
(Hz)
640 x 350
31.46
70.09
720 x 400
31.46
70.08
640 x 480
31.46
59.94
800 x 600
37.87
60.31
1024 x 768
48.36
60.00
1152 x 864
54.34
60.05
1280 x 1024
63.98
60.02
1360 x 768
47.71
60.01
1920 x 1080
67.50
60.00
67.50
56.25
54.00
53.95
54.00
30.00
25.00
24.00
23.97
24.00
3840 x 2160
4096 x 2160
3D supported mode (Only 3D models)
ENGLISH
• Video, which is input as below media contents is switched into the 3D screen automatically. The method for 3D digital broadcast may differ
depending on the signal environment. If video is not switched automatically into 3D, manually convert the settings to view 3D images. For
models supporting Miracast / Intel® WiDi, you can set the 3D mode.
3D supported mode automatically
Input
RF
Signal
Horizontal
Frequency (kHz)
Vertical
Frequency (Hz)
1280 x 720
37.50
50.00
1920 x 1080
28.13
50.00
640 x 480
720 x 480
31.46 / 31.50
59.94/ 60.00
Frame Packing, Line Alternative
Top & Bottom, Side by Side (Half), Side by Side (Full)
62.93 /63.00
59.94 / 60.00
31.25
50.00
USB
DTV
50.00
44.96 / 45.00
59.94 / 60.00
75.00
50.00
59.94 / 60.00
28.12
50.00
33.72 / 33.75
59.94 / 60.00
56.25
50.00
67.43/67.50
59.94 / 60.00
26.97 / 27.00
23.97 / 24.00
28.12
25.00
33.71 / 33.75
29.97 / 30.00
43.94 / 54.00
23.97 / 24.00
56.25
25.00
67.43 / 67.50
29.97 / 30.00
56.25
50.00
67.43 / 67.50
59.94 / 60.00
1080p
33.75
30.00
2160p
67.50
30.00
1920 x 1080
Frame Packing, Line Alternative
Top & Bottom, Side by Side (Half),
Side by Side (Full), Frame Packing
Top & Bottom, Side by Side (Half), Side by Side (Full)
Frame Packing, Line Alternative
37.50
89.91/90.00
HDMI
Top & Bottom, Side by Side (Half),
Side by Side (Full)
31.46 / 31.50
62.50
1280 x 720
2D to 3D, Side by Side, Top & Bottom
62.93 / 63.00
15.62
720 x 576
Playable 3D video format
Top & Bottom, Side by Side (Half), Side by Side (Full)
Frame Packing, Line Alternative
Top & Bottom, Side by Side (Half), Side by Side (Full)
Frame Packing
Top & Bottom, Side by Side (Half), Side by Side (Full)
Frame Packing, Line Alternative
Top & Bottom, Side by Side (Half)
Side by Side (Half), Top & Bottom, Checker Board, MPO (Photo),
JPS (Photo)
Signal
Playable 3D video format
Frame Compatible
Side by Side (Half), Top & Bottom
19
3D supported mode manually
Signal
Input
ENGLISH
DTV / ATV
(SCART)
HDMI-PC
Resolution
Horizontal
Frequency (kHz)
Vertical
Frequency (Hz)
HD / SD
-
-
SD
-
-
1024 x 768
48.36
1360 x 768
47.71
1920 x 1080
67.50
54.00
24.00
3840 x 2160
56.25
25.00
67.50
30.00
4096 x 2160
54.00
24.00
Others
-
-
720 x 480
31.50
60.00
720 x 576
31.25
50.00
45.00
60.00
37.50
50.00
1280 x 720
1920 x 1080i
1920 x 1080p
HDMI-DTV
3840 x 2160
4096 x 2160
33.75
60.00
50.00
27.00
24.00
28.12
25.00
33.75
30.00
67.50
60.00
56.25
50.00
53.95
23.97
54.00
24.00
56.25
25.00
61.43
29.97
112.50
135.00
1 : Only HDMI IN 1, HDMI IN 2 port
20
2D to 3D, Side by Side (Half), Top & Bottom
2D to 3D, Side by Side (Half), Top & Bottom
60.00
28.12
67.50
Playable 3D video format
1
2D to 3D, Side by Side (Half),
Top & Bottom, Checker Board, Row Interleaving,
Column Interleaving
2D to 3D,
Side by Side (Half),
Top & Bottom (half)
2D to 3D,
Side by Side (Half),
Top & Bottom
2D to 3D, Side by Side (Half),
Top & Bottom, Checker Board, Row Interleaving,
Column Interleaving
2D to 3D, Side by Side (Half),
Top & Bottom
2D to 3D, Side by Side (Half),
Top & Bottom, Checker Board, Row Interleaving,
Column Interleaving
2D to 3D, Side by Side (Half),
Top & Bottom (Half)
30.00
50.00
60.00
2D to 3D, Side by Side (Half),
Top & Bottom
3D supported mode manually
Signal
Input
USB (Photo)
Miracast/
Intel® WiDi
Horizontal
Frequency (kHz)
Vertical
Frequency (Hz)
Playable 3D video format
Under 704 x 480
-
-
2D to 3D
Over 704 x 480
under 1080p
interlaced
-
-
2D to 3D, Side by Side (Half),
Top & Bottom
Over 704 x 480
under 1080p
progressive
-
50.00 / 60.00
-
Others
Over 2160p
-
24/25/30/50/60
Under 320 x 240
-
-
2D to 3D
Over 320 x 240
-
-
2D to 3D, Side by Side (Half), Top & Bottom
-
-
-
2D to 3D
ENGLISH
USB (Movie)
Resolution
2D to 3D, Side by Side (Half),
Top & Bottom, Checker Board, Row Interleaving, Column
Interleaving
2D to 3D, Side by Side (Half),
Top & Bottom
21
Photo format
ENGLISH
1
Video codec
File
Format
Format
Resolution
.jpeg, .jpg,
.jpe
JPEG
Minimum: 64 x 64
Maximum: 15,360 (W) x 8,640 (H) /
Progressive Type: 1,920 (W) x 1,440 (H)
.png
PNG
Minimum: 64 x 64
Maximum: 5,760 (W) x 5,760 (H)
.bmp
BMP
Minimum: 64 x 64
Maximum: 1,920 (W) x 1,080 (H)
.jps
JPS
.mpo
MPO
Minimum: 64 x 64
Maximum: 15,360 (W) x 8,640 (H)
1 : Only 3D mode
Audio format
File
Format
.mp3
.wav
.ogg
.wma
Item
Info
Bit rate
32 Kbps - 320 Kbps
Sample freq.
16 kHz - 48 kHz
Support
MPEG1, MPEG2
Channels
mono, stereo
Bit rate
-
Sample freq.
~384 kHz
Support
PCM
Channels
mono, stereo
Bit rate
64 Kbps - 500 Kbps
Sample freq.
8 kHz - 48 kHz
Support
Vorbis
Channels
mono, stereo
Bit rate
~1.5 Mbps
Sample freq.
8 kHz - 192 kHz
Support
WMA
Channels
up to 6 ch
• The number of supported programmes may vary depending on the
sample frequency.
22
Extenstion
.asf
.wmv
.divx
.avi
Codec
Video
VC-1 Advanced Profile (WMVA
excluded), VC-1 Simple and Main
Profiles
Audio
WMA Standard (WMA v1/WMA Speech
excluded), WMA 9 Professional
Video
DivX3.11, DivX4, DivX5, DivX6,
XViD(except 3 warp-point GMC), H.264/
AVC, Motion Jpeg, MPEG-4
Audio
MPEG-1 Layer I, II, MPEG-1 Layer III
(MP3), Dolby Digital, LPCM, ADPCM, DTS
.mp4
.m4v
.mov
Video
H.264/AVC, MPEG-4, HEVC
Audio
AAC, MPEG-1 Layer III (MP3)
.3gp
.3g2
Video
H.264/AVC, MPEG-4
Audio
AAC, AMR-NB, AMR-WB
Video
MPEG-2, MPEG-4, H.264/AVC, VP8,
VP9, HEVC
Audio
Dolby Digital, PCM, DTS, MPEG-1 Layer I,
II, MPEG-1 Layer III (MP3), AAC
.mkv
.ts
.trp
.tp
.mts
.mpg
.mpeg
.dat
.vob
.rm
.rmvb
Video
H.264/AVC, MPEG-2, HEVC
Audio
MPEG-1 Layer I, II, MPEG-1 Layer III
(MP3), Dolby Digital, Dolby Digital Plus,
AAC, PCM
Video
MPEG-1, MPEG-2
Audio
MPEG-1 Layer I, II, MPEG-1 Layer III
(MP3)
Video
MPEG-1, MPEG-2
Audio
Dolby Digital, MPEG-1 Layer I, II,
DVD-LPCM
Video
RV30, RV40
Audio
Realaudio6(cook), AAC LC, HE-AAC
• This feature is available in certain countries only.
Record the model number and serial number of the TV.
Refer to the label on the back cover and quote this
information to your dealer when requiring any service.
MODEL
SERIAL
Download PDF
Similar pages