No punchdowns needed with this feed-through panel.

JPM804A-R2
February
2010
MT1000A-85-R4
JPM806A-R2
JPM808A-R2
JPM810A-R2
Feed-Through CAT5e Patch Panels
No punchdowns needed with this feed-through
BLACK BOX
panel.
®
• Unique design features RJ-45 plugs on both sides of the patch panel.
• Feed-through connectors provide super-easy cable management.
• Perfect for voice and data transmission up to 1 Gigabit.
Specifications
Overview
Standards — Category 5e
The Feed-Through CAT5e Patch Panels meet Category 5e
performance requirements and provide patching without
punching down the wires to the ports. These sturdy panels
install in relay racks or communications cabinets.
Connectors — JPM804A-R2: (24) shielded RJ-45 on front, (24) shielded RJ-45 on back;
JPM806A-R2: (48) shielded RJ-45 on front, (48) shielded
RJ-45 on back;
JPM808A-R2: (24) unshielded RJ-45 on front,
(24) unshielded RJ-45 on back;
JPM810A-R2: (48) unshielded RJ-45 on front,
(48) unshielded RJ-45 on back
Size — JPM804A-R2, JPM808A-R2: 1.75"H (1U) x 19"W x
4.5"D (4.4 x 48.3 x 11.4 cm);
JPM806A-R2, JPM810A-R2: 3.5"H (2U) x 19"W x 4.5"D
(8.9 x 48.3 x 11.4 cm)
Weight — JPM804A-R2: 1.485 lb. (0.675 kg); JPM806A-R2: 2.78 lb. (1.265 kg);
JPM808A-R2: 1.18 lb. (0.54 kg);
JPM810A-R2: 2.18 lb. (0.993 kg)
After ordering a CAT5e Patch Panel, you should have received
the following items:
• (1) CAT5e Patch Panel
• (1) cable management bar for JPM804A-R2 and
JPM808A-R2, or (2) cable management bars for
JPM806A-R2 and JPM810A-R2
• (4) 10-32 cuphead screws
• (4) 12-24 cuphead screws
• This users’ manual
If anything is missing or damaged, please contact Black Box at
724-746-5500.
For installation instructions, turn this page over…
Customer
Support
Information
Order toll-free in the U.S.: Call 877-877-BBOX (outside U.S. call 724-746-5500)
FREE technical support 24 hours a day, 7 days a week: Call 724-746-5500 or fax 724-746-0746
Mailing address: Black Box Corporation, 1000 Park Drive, Lawrence, PA 15055-1018
Web site: www.blackbox.com • E-mail: info@blackbox.com
Installation
Use the Feed-Through CAT5e Patch Panels with or without the cable management bar. It neatly organizes and supports the
cables that are installed in rear of the patch panel.
Without using the cable management bar:
1. Find an empty rack space on a relay rack or communications cabinet.
2. Install the panel with the supplied 10-32 or 12-24 cuphead screws.
3. Install the RJ-45 patch cables on the front and rear connectors to make the connections.
Using the cable management bar:
1. Remove the two cuphead screws from each side of the patch panel.
2. Position the cable management bar on the patch panel and reinstall the two cuphead screws.
3. Install a patch cable in one of the panel’s rear ports. Unscrew the corresponding silver clip behind the installed port and
position the patch cable under the silver bracket. Tighten the screw.
4. For a 48-port patch panel (JPM806A-R2 or JPM810A-R2), repeat Steps 1 through 3 to install the second cable management
bar.
Installation is complete.
© Copyright 2011. Black Box Corporation. All rights reserved. Printed in U.S.A. Black Box® and the Double Diamond logo are registered trademarks of BB Technologies, Inc. Any third-party
trademarks appearing in this manual are acknowledged to be the property of their respective owners.
JPM804A-R2, version 2
FREE, live, 24/7 Tech Support is just 30 seconds away.
724-746-5500 | blackbox.com
Download PDF
Similar pages