308360C Stainless Steel Dura-Flo 1200 Pumps (ATEX)

Instructions – Parts List
Parts
STAINLESS STEEL
Dura–Flot 1200 Pumps
308360C
With Severe–Duty Rod and Cylinder
Part No. 237516 Pump, Series A,
21:1 Ratio, with Bulldogr Air Motor
14.5 MPa (145 bar, 2100 psi) Maximum Fluid Working Pressure
0.7 MPa (7 bar, 100 psi) Maximum Air Input Pressure
Part No. 237517 Pump, Series A,
13:1 Ratio, with Senatorr Air Motor
9 MPa (90 bar, 1300 psi) Maximum Fluid Working Pressure
0.7 MPa (7 bar, 100 psi) Maximum Air Input Pressure
Model 237517
04143
Model 237516
Read warnings and instructions.
See page 2 for model numbers and
maximum working pressures.
GRACO INC.ąP.O. BOX 1441ąMINNEAPOLIS, MNą55440-1441
Copyright 2002, Graco Inc. is registered to I.S. EN ISO 9001
04140
Table of Contents
Warnings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2
Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
Operation/Maintenance . . . . . . . . . . . . . . . . . . . . . . . . . 8
Troubleshooting Chart . . . . . . . . . . . . . . . . . . . . . . . . . 11
Service . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12
Required Tools . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12
Disconnecting the Displacement Pump . . . . . . . 12
Reconnecting the Displacement Pump . . . . . . . . 12
Displacement Pump Service . . . . . . . . . . . . . . . . 14
Parts Drawings and Parts Lists . . . . . . . . . . . . . . . . . . 18
Pump Assemblies . . . . . . . . . . . . . . . . . . . . . . . . . . 18
Displacement Pump . . . . . . . . . . . . . . . . . . . . . . . . 19
Technical Data . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21
Dimensions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23
Mounting Hole Layout . . . . . . . . . . . . . . . . . . . . . . . . . . 23
Graco Standard Warranty . . . . . . . . . . . . . . . . . . . . . . 24
Graco Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24
Symbols
Warning Symbol
WARNING
This symbol alerts you to the possibility of serious
injury or death if you do not follow the instructions.
Caution Symbol
CAUTION
This symbol alerts you to the possibility of damage to
or destruction of equipment if you do not follow the
instructions.
WARNING
EQUIPMENT MISUSE HAZARD
Equipment misuse can cause the equipment to rupture or malfunction and result in serious injury.
INSTRUCTIONS
D This equipment is for professional use only.
D Read all instruction manuals, tags, and labels before operating the equipment.
D Use the equipment only for its intended purpose. If you are not sure, call Graco Technical Assistance at 1–800–543–0339.
D Do not alter or modify this equipment.
D Check equipment daily. Repair or replace worn or damaged parts immediately.
D Do not exceed the maximum working pressure of the lowest rated system component. Refer to the
Technical Data on pages 21–22 for the maximum working pressure of this equipment.
D Use fluids and solvents which are compatible with the equipment wetted parts. Refer to the Technical Data section of all equipment manuals. Read the fluid and solvent manufacturer’s warnings.
D Do not use hoses to pull equipment.
D Route hoses away from traffic areas, sharp edges, moving parts, and hot surfaces. Do not expose
Graco hoses to temperatures above 82_C (180_F) or below –40_C (–40_F).
D Wear hearing protection when operating this equipment.
D Do not lift pressurized equipment.
D Comply with all applicable local, state, and national fire, electrical, and safety regulations.
2
308360
WARNING
INJECTION HAZARD
Spray from the gun, leaks or ruptured components can inject fluid into your body and cause extremely
serious injury, including the need for amputation. Fluid splashed in the eyes or on the skin can also
cause serious injury.
D Fluid injected into the skin might look like just a cut, but it is a serious injury. Get immediate medical attention.
D Do not point the gun at anyone or at any part of the body.
D Do not put your hand or fingers over the spray tip.
D Do not stop or deflect leaks with your hand, body, glove or rag.
D Do not “blow back” fluid; this is not an air spray system.
D Always have the tip guard and the trigger guard on the gun when spraying.
D Check the gun diffuser operation weekly. Refer to the gun manual.
D Be sure the gun trigger safety operates before spraying.
D Lock the gun trigger safety when you stop spraying.
D Follow the Pressure Relief Procedure on page 8 if the spray tip clogs and before cleaning,
checking or servicing the equipment.
D Tighten all fluid connections before operating the equipment.
D Check the hoses, tubes, and couplings daily. Replace worn or damaged parts immediately.
Do not repair high pressure couplings; you must replace the entire hose.
D Fluid hoses must have spring guards on both ends, to help protect them from rupture caused by
kinks or bends near the couplings.
MOVING PARTS HAZARD
Moving parts, such as the air motor piston, can pinch or amputate your fingers.
D Keep clear of all moving parts when starting or operating the pump.
D Before servicing the equipment, follow the Pressure Relief Procedure on page 8 to prevent the
equipment from starting unexpectedly.
308360
3
WARNING
FIRE AND EXPLOSION HAZARD
Improper grounding, poor ventilation, open flames or sparks can cause a hazardous condition and result in a fire or explosion and serious injury.
D Ground the equipment and the object being sprayed. Refer to Grounding on page 5.
D If there is any static sparking or you feel an electric shock while using this equipment, stop spraying immediately. Do not use the equipment until you identify and correct the problem.
D Provide fresh air ventilation to avoid the buildup of flammable fumes from solvents or the fluid being sprayed.
D Keep the spray area free of debris, including solvent, rags, and gasoline.
D Electrically disconnect all equipment in the spray area.
D Extinguish all open flames or pilot lights in the spray area.
D Do not smoke in the spray area.
D Do not turn on or off any light switch in the spray area while operating or if fumes are present.
D Do not operate a gasoline engine in the spray area.
TOXIC FLUID HAZARD
Hazardous fluid or toxic fumes can cause serious injury or death if splashed in the eyes or on the skin,
inhaled, or swallowed.
D Know the specific hazards of the fluid you are using.
D Store hazardous fluid in an approved container. Dispose of hazardous fluid according to all local,
state and national guidelines.
D Always wear protective eyewear, gloves, clothing and respirator as recommended by the fluid and
solvent manufacturer.
4
308360
Installation
3. Air compressor: follow manufacturer’s recommendations.
General Information
NOTE: Reference numbers and letters in parentheses
in the text refer to the callouts in the figures and the
parts drawing.
NOTE: Always use Genuine Graco Parts and Accessories, available from your Graco distributor. Refer to
Product Data Sheet, Form No. 305713 (Senator
Pumps) and Form No. 305714 (Bulldog Pumps). If you
supply your own accessories, be sure they are adequately sized and pressure rated for your system.
Grounding
WARNING
FIRE AND EXPLOSION HAZARD
Before operating the pump, ground the
system as explained below. Also read
the section FIRE OR EXPLOSION HAZARD on page 4.
4. Spray gun: ground through connection to a properly grounded fluid hose and pump.
5. Fluid supply container: follow your local code.
6. Object being sprayed: follow your local code.
7. Solvent pails used when flushing: follow your local
code. Use only metal pails, which are conductive,
placed on a grounded surface. Do not place the
pail on a nonconductive surface, such as paper or
cardboard, which interrupts the grounding continuity.
8. To maintain grounding continuity when flushing or
relieving pressure, hold a metal part of the spray
gun firmly to the side of a grounded metal pail,
then trigger the gun.
System Accessories
1. Pump: use a ground wire and clamp. See Fig. 1.
Loosen the grounding lug locknut (W) and washer
(X). Insert one end of a 1.5 mm@ (12 ga) minimum
ground wire (Y) into the slot in lug (Z) and tighten
the locknut securely. Connect the other end of the
wire to a true earth ground. Order Part No. 237569
Ground Wire and Clamp.
Fig. 2 is only a guide for selecting and installing
system components and accessories. Contact your
Graco representative or Graco Technical Assistance
(1–800–543–0339) for assistance in designing a
system to suit your particular needs.
Air and Fluid Hoses
Be sure all air hoses (H) and fluid hoses (N and P) are
properly sized and pressure-rated for your system.
Use only electrically conductive hoses. Fluid hoses
must have spring guards on both ends. Use a whip
hose (P) and a swivel (R) between the main fluid hose
(N) and the gun (S) to allow freer gun movement.
W
X
Y
Z
Mounting Accessories
Fig. 1
Mount the pump (A) to suit the type of installation
planned. Fig. 2 illustrates a wall mount system. Pump
dimensions and the mounting hole layout are shown
on page 23.
2. Air and fluid hoses: use only electrically conductive
hoses.
If you are using a floor stand, refer to its separate
manual for installation and operation instructions.
0864
308360
5
Installation
System Accessories (continued)
D
A pump runaway valve (C) senses when the
pump is running too fast and automatically shuts
off the air to the motor. A pump which runs too fast
can be seriously damaged.
D
An air manifold (G) has a 3/4 npsm(f) swivel air
inlet. It mounts to the pump support bracket, and
provides ports for connecting lines to air-powered
accessories.
D
An air line filter (J) removes harmful dirt and
moisture from the compressed air supply. Also,
install a drain valve (W) at the bottom of each air
line drop, to drain off moisture.
D
A second bleed-type air valve (K) isolates the air
line accessories for servicing. Locate upstream
from all other air line accessories.
WARNING
A bleed-type master air valve (E) and a fluid drain
valve (M) are required in your system. These accessories help reduce the risk of serious injury, including fluid injection and splashing of fluid in the
eyes or on the skin, and injury from moving parts if
you are adjusting or repairing the pump.
The bleed-type master air valve relieves air trapped
between this valve and the pump after the air is
shut off. Trapped air can cause the pump to cycle
unexpectedly. Locate the valve close to the pump.
Order Part No. 107141.
The fluid drain valve assists in relieving fluid pressure in the displacement pump, hose, and gun.
Triggering the gun to relieve pressure may not be
sufficient. Order Part No. 235992.
Fluid Line Accessories
Install the following accessories in the locations shown
in Fig. 2, using adapters as necessary:
D
A fluid filter (L) with a 60 mesh (250 micron)
stainless steel element, to filter particles from the
fluid as it leaves the pump.
D
A fluid drain valve (M), which is required in your
system, helps relieve fluid pressure in the hose
and gun (see the WARNING at left).
D
A gun (S) dispenses the fluid. The gun shown in
Fig. 2 is an airless spray gun for light to medium
viscosity fluids.
D
A gun swivel (R) allows freer gun movement.
D
A suction kit (T) allows the pump to draw fluid
from a supply container.
Air Line Accessories
Install the following accessories in the locations shown
in Fig. 2, using adapters as necessary:
D
D
D
6
An air line lubricator (D) provides automatic air
motor lubrication.
A bleed-type master air valve (E) is required in
your system to relieve air trapped between it and
the air motor when the valve is closed (see the
WARNING above). Be sure the bleed valve is easily accessible from the pump, and is located
downstream from the air regulator.
CAUTION
An air regulator (F) controls pump speed and outlet pressure by adjusting the air pressure to the
pump. Locate the regulator close to the pump, but
upstream from the bleed-type master air valve.
308360
To prevent intake valve damage, always apply PTFE
tape to the female threads of the intake valve before
connecting a suction hose or fitting to the intake.
Installation
TYPICAL INSTALLATION
KEY
A
B
C
D
E
F
G
H
J
K
Electrically Conductive Air Supply Hose
Air Line Filter
Bleed-Type Master Air Valve
(for accessories)
L Fluid Filter
M Fluid Drain Valve (required)
N Electrically Conductive
Fluid Supply Hose
Pump
Wall Bracket
Pump Runaway Valve
Air Line Lubricator
Bleed-Type Master Air Valve
(required, for pump)
Pump Air Regulator
Air Manifold
J
P
R
S
T
Y
Fluid Whip Hose
Gun Swivel
Airless Spray Gun
Suction Kit
Ground Wire and Clamp
(required; see page 5
for installation instructions)
W Air Line Drain Valve
K
MAIN AIR LINE
Y
D
A
S
E
F
C
G
B
H
R
P
L
N
W
M
T
04177
Fig. 2
308360
7
Operation/Maintenance
Pressure Relief Procedure
WARNING
INJECTION HAZARD
The system pressure must be manually
relieved to prevent the system from
starting or spraying accidentally. Fluid
under high pressure can be injected through the
skin and cause serious injury. To reduce the risk of
an injury from injection, splashing fluid, or moving
parts, follow the Pressure Relief Procedure
whenever you:
D
D
D
D
are instructed to relieve the pressure,
stop spraying,
check or service any of the system equipment,
or install or clean the spray tips.
Packing Nut/Wet-Cup
Before starting, fill the packing nut (2) 1/3 full with
Graco Throat Seal Liquid (TSL) or compatible solvent.
See Fig. 3.
WARNING
To reduce the risk of serious injury whenever you
are instructed to relieve pressure, always follow the
Pressure Relief Procedure at left.
The packing nut is torqued at the factory and is ready
for operation. If it becomes loose and there is leaking
from the throat packings, relieve the pressure, then
torque the nut to 136–149 N.m (100–110 ft-lb) using
the supplied wrench (110). Do this whenever necessary. Do not overtighten the packing nut.
1. Lock the gun/valve trigger safety.
2. Shut off the air supply to the pump.
Model
237516
Shown
3. Close the bleed-type master air valve (required in
your system).
4. Unlock the gun/valve trigger safety.
5. Hold a metal part of the gun firmly to the side of a
grounded metal pail, and trigger the gun to relieve
pressure.
6. Lock the gun/valve trigger safety.
1
2
110
7. Open the drain valve (required in your system),
having a container ready to catch the drainage.
8. Leave the drain valve open until you are ready to
spray again.
1
If you suspect that the spray tip or hose is completely
clogged, or that pressure has not been fully relieved
after following the steps above, very slowly loosen the
tip guard retaining nut or hose end coupling and relieve
pressure gradually, then loosen completely. Now clear
the tip or hose.
8
308360
Torque to 136–149 N.m
(100–110 ft-lb)
04143
Fig. 3
Operation/Maintenance
Flush the Pump Before First Use
The pump is tested with lightweight oil, which is left in
to protect the pump parts. If the fluid you are using
may be contaminated by the oil, flush it out with a
compatible solvent. See Flushing on page 10.
Starting and Adjusting the Pump
1. See Fig. 2. Connect the suction kit (T) to the
pump’s fluid inlet. Place the tube into the fluid supply.
CAUTION
To prevent intake valve damage, always apply PTFE
tape to the female threads of the intake valve before
connecting a suction hose or fitting to the intake.
2. Close the air regulator (F).
3. Open the pump’s bleed-type master air valve (E).
4. Hold a metal part of the gun (S) firmly to the side
of a grounded metal pail and hold the trigger open.
5. Slowly open the regulator until the pump starts.
6. Cycle the pump slowly until all air is pushed out
and the pump and hoses are fully primed.
7. Release the gun trigger and lock the trigger safety.
The pump should stall against pressure.
8. If the pump fails to prime properly, open the drain
valve (M). Use the drain valve as a priming valve
until the fluid flows from the valve. Close the valve.
NOTE: When changing fluid containers with the hose
and gun already primed, open the drain valve (M) to
help prime the pump and vent air before it enters the
hose. Close the drain valve when all air is eliminated.
CAUTION
Do not allow the pump to run dry. It will quickly accelerate to a high speed, causing damage. If your pump
is running too fast, stop it immediately and check the
fluid supply. If the container is empty and air has
been pumped into the lines, refill the container and
prime the pump and the lines, or flush and leave it
filled with a compatible solvent. Eliminate all air from
the fluid system.
9. With the pump and lines primed, and with adequate air pressure and volume supplied, the pump
will start and stop as you open and close the gun.
In a circulating system, the pump will speed up or
slow down on demand, until the air supply is shut
off.
WARNING
COMPONENT RUPTURE HAZARD
To reduce the risk of overpressurizing
your system, which could cause component rupture and serious injury, never
exceed the specified Maximum Incoming Air Pressure to the pump (see the Technical Data, on
pages 21 and 22).
10. Use the air regulator (F) to control pump speed
and fluid pressure. Always use the lowest air pressure necessary to get the desired results. Higher
pressures cause premature tip and pump wear.
308360
9
Operation/Maintenance
Shutdown and Care of the Pump
WARNING
To reduce the risk of serious injury whenever you
are instructed to relieve pressure, always follow the
Pressure Relief Procedure on page 8.
For overnight shutdown, stop the pump at the bottom
of its stroke to prevent fluid from drying on the exposed displacement rod and damaging the throat
packings. Relieve the pressure.
Flush with a fluid that is compatible with the fluid you
are pumping and with the wetted parts in your system.
Check with your fluid manufacturer or supplier for recommended flushing fluids and flushing frequency. Always flush the pump before fluid dries on the displacement rod.
WARNING
To reduce the risk of serious injury whenever you
are instructed to relieve pressure, always follow the
Pressure Relief Procedure on page 8.
1. Relieve the pressure.
Always flush the pump before the fluid dries on the
displacement rod. See Flushing below.
3. Hold a metal part of the gun firmly to the side of a
grounded metal pail.
Flushing
WARNING
FIRE AND EXPLOSION HAZARD
Before flushing, read the section FIRE
OR EXPLOSION HAZARD on page 4.
Be sure the entire system and flushing
pails are properly grounded. Refer to
Grounding on page 5.
10
2. Remove the spray tip from the gun.
308360
4. Start the pump. Always use the lowest possible
fluid pressure when flushing.
5. Trigger the gun.
6. Flush the system until clear solvent flows from the
gun.
7. Relieve the pressure.
Troubleshooting Chart
WARNING
To reduce the risk of serious injury whenever you
are instructed to relieve pressure, always follow the
Pressure Relief Procedure on page 8.
PROBLEM
1. Relieve the pressure.
2. Check all possible causes and problems before
disassembling the pump.
CAUSE
SOLUTION
The pump fails to oper- Restricted air line or an inadequate air Clear the line; increase the air supply.
ate.
supply; closed or clogged valves.
Check that the valves are open.
Obstructed fluid hose or gun;
the fluid hose ID is too small.
Open, clear*; use a hose with a larger ID.
Fluid has dried on the displacement rod. Clean the rod; always stop the pump at the bottom
of its stroke;
keep the wet-cup 1/3 filled with a compatible solvent.
Dirty, worn, or damaged motor parts.
Clean or repair; see the separate motor manual.
The pump operates, Restricted air line or an inadequate air Clear the line; increase the air supply.
but the output is low on supply; closed or clogged valves.
Check that the valves are open.
both strokes.
Obstructed fluid hose or gun;
the fluid hose ID is too small.
Open, clear*; use a hose with a larger ID.
Worn packings in the displacement Replace the packings.
pump.
The pump operates, Held open or worn intake valve.
but the output is low on
the downstroke.
Clear the valve; service.
The pump operates, Held open or worn piston valve or pack- Clear the valve; replace the packings.
but the output is low on ings.
the upstroke.
Erratic or accelerated Exhausted fluid supply.
pump speed.
Refill the supply and prime the pump.
Held open or worn piston valve or pack- Clear the valve; replace the packings.
ings.
Held open or worn intake valve.
*
Clear the valve; service.
To determine if the fluid hose or gun is obstructed, follow the Pressure Relief Procedure on page 8. Disconnect the fluid hose and place a container at the pump fluid outlet to catch any fluid. Turn on the air just enough
to start the pump. If the pump starts when the air is turned on, the obstruction is in the fluid hose or gun.
NOTE: If you experience air motor icing, call Graco Technical Assistance (1–800–543–0339).
308360
11
Service
Required Tools
D
D
D
D
D
D
D
D
Set of adjustable wrenches
Large pipe wrench
Torque wrench
Rubber mallet
O-ring pick
Large vise
Thread lubricant
Thread sealant
Disconnecting the Displacement Pump
1. Flush the pump, if possible. Stop the pump at the
bottom of its stroke.
WARNING
To reduce the risk of serious injury whenever you
are instructed to relieve pressure, always follow the
Pressure Relief Procedure on page 8.
2. Relieve the pressure.
3. Disconnect the air hose and the fluid hose.
4. Disconnect the displacement pump (109) from the
motor (101) as follows. Note the relative position of
the pump’s fluid outlet (U) to the air inlet (V) of the
motor. If the motor does not require servicing,
leave it attached to its mounting.
CAUTION
Be sure to use at least two people when lifting, moving, or disconnecting the pump. This pump is too
heavy for one person. If you are disconnecting the
displacement pump from a motor which is still
mounted (for example, on a wall bracket), be sure to
support the displacement pump while it is being disconnected, to prevent it from falling and causing injury or property damage. Do this by securely bracing
the pump, or by having at least two people hold it
while another disconnects it.
If the pump is mounted on a cart, slowly tip the cart
backward until the handle rests on the ground, then
disconnect the displacement pump.
12
308360
5. Using an adjustable wrench (or hammer and
punch), unscrew the coupling nut (106) from the
motor shaft (W). Do not lose or drop the coupling
collars (107). See Fig. 4.
6. Hold the tie rod flats with a wrench to keep the
rods from turning. Unscrew the nuts (108) from the
tie rods (105). Carefully remove the displacement
pump (109) from the motor (101).
7. Refer to page 14 for displacement pump service.
To service the air motor, refer to the separate motor manual, supplied.
Reconnecting the Displacement Pump
1. Make sure the coupling nut (106) and the coupling
collars (107) are in place on the displacement rod
(1). See Fig. 4.
2. Use at least two people to hold the displacement
pump while another reconnects it to the motor (see
the CAUTION at left). Orient the pump’s fluid outlet (U) to the air inlet (V) as was noted in step 4
under Disconnecting the Displacement Pump.
Position the displacement pump (109) on the tie
rods (105).
3. Screw the nuts (108) onto the tie rods (105) and
torque to 81–89 N.m (60–66 ft-lb).
4. Screw the coupling nut onto the motor shaft (W)
loosely. Hold the motor shaft flats with a wrench to
keep it from turning. Use an adjustable wrench to
tighten the coupling nut. Torque to 196–210 N.m
(145–155 ft-lb).
5. Reconnect all hoses. Reconnect the ground wire if
it was disconnected. Fill the packing nut (2) 1/3 full
of Graco Throat Seal Liquid or compatible solvent.
6. Turn on the air supply. Run the pump slowly to ensure proper operation.
WARNING
To reduce the risk of serious injury whenever you
are instructed to relieve pressure, always follow the
Pressure Relief Procedure on page 8.
7. Before returning the pump to production, relieve
the pressure and retorque the packing nut (2) to
136–149 N.m (100–110 ft-lb).
Service
V
Model 237516 Shown
101
W
110
107
106
2
1
3
105
3
108
2
1
109
U
1
Torque to 136–149 N.m (100–110 ft-lb)
2
Torque to 196–210 N.m (145–155 ft-lb)
3
Torque to 81–89 N.m (60–66 ft-lb)
04142
Fig. 4
308360
13
Service
DISPLACEMENT PUMP SERVICE
Disassembly
When disassembling the pump, lay out all the removed
parts in sequence, to ease reassembly.
NOTE: Packing Repair Kits are available. For the best
results, use all the new parts in the kit. Kit parts are
marked with an asterisk, for example (3*). You can
also convert the pump to different packing materials.
Refer to page 20.
1. Place the pump lengthwise in a large vise, with the
jaws on the outlet housing (7) as shown in Fig. 5.
Using the supplied wrench (110), loosen, but do
not remove, the packing nut (2).
2. Apply a pipe wrench to the flats of the intake valve
(19). Unscrew the intake valve (19) from the intake
housing (18). Be careful to catch the intake ball
(17) as you remove the intake valve, so that it
does not fall and suffer damage. Remove the seal
(8) from the intake valve. Inspect the ball and the
seat (D) of the intake valve for wear or damage.
3. Apply a pipe wrench to the hex of the valve housing (18). The pump assembly may separate at joint
A or joint B.
CAUTION
To reduce the possibility of costly damage to the rod
(1) and cylinder (9), always use a rubber mallet to
drive the rod out of the cylinder. Never use a hammer.
D
If the assembly separates at joint A:
a. Unscrew the valve housing (18) from the cylinder. Using a rubber mallet, drive the displacement rod (1) and piston assembly out of the
outlet housing (7) and cylinder (9) until the piston comes free. Pull the rod and piston from
the cylinder, being careful not to scratch the
parts.
b. Unscrew the cylinder (9) from the outlet housing (7), using a pipe wrench. Remove the two
seals (8) from the cylinder. Shine a light into
the cylinder (9) to inspect the inner surface for
scoring or wear. Now go to step 4.
14
308360
D
If the assembly separates at joint B:
a. Unscrew the cylinder (9) and valve housing
(18) from the outlet housing (7). Gently pull the
cylinder and valve housing straight out of the
outlet housing; the displacement rod (1) and
piston assembly will come out with these
parts.
b. Place the valve housing (18) in the vise and
unscrew the cylinder (9) from the housing, using a pipe wrench. The displacement rod (1)
and piston assembly will remain in the cylinder.
c.
Using a rubber mallet, drive the displacement
rod (1) and piston assembly out of the cylinder
(9) until the piston comes free. Pull the rod and
piston from the cylinder, being careful not to
scratch the parts.
d. Remove the two seals (8) from the cylinder.
Shine a light into the cylinder (9) to inspect the
inner surface for scoring or wear. Now go to
step 4.
4. Place the flats of the piston seat housing (16) in a
vise, as shown in Fig. 6.
5. Using an adjustable wrench, unscrew the piston
ball housing (10) from the piston seat housing. Be
careful to catch the piston ball (11) as you separate the piston seat housing and ball housing, so
that it does not fall and suffer damage.
6. Examine the displacement rod (1) for scratches or
other damage. Only if the rod needs replacement, unscrew it from the piston ball housing (10),
using an adjustable wrench on the flats of the rod.
7. Remove the glands and v-packings (P) from the
piston seat housing (16). Inspect the ball (11), and
the seat (E) and guides (F) on the housing for
wear or damage. See Fig. 7.
8. Unscrew the packing nut (2) from the outlet housing (7). Remove the glands and v-packings (T).
See Fig. 7.
9. Clean all parts with a compatible solvent and inspect them for wear or damage.
Service
D
1
1
7
18
19
9
3
2
17*
8*
2
A
1
B
2
1
Torque to 325–353 N.m (240–260 ft-lb).
2
Lubricate.
3
Torque to 190–217 N.m (140–160 ft-lb).
03794A
Fig. 5
1
1
1
10
11*
1
10
1
16
16
1
03793A
Torque to 386–407 N.m (285–300 ft-lb).
Fig. 6
308360
15
Service
Reassembly
1. If it was necessary to remove the piston ball housing (10) from the displacement rod (1), clean the
threads of the rod and the ball housing. Screw the
ball housing onto the rod, hand tight. Place the
flats of the piston ball housing in a vise and torque
the rod to 386–407 N.m (285–300 ft-lb). See Fig.
7.
2. For standard displacement pump 237514, place
the piston packings on the piston seat housing (16)
in the following order, with the lips of the v-packings facing up: the female gland (15*), one PTFE
v-packing (14*), four leather
v-packings (12*), and the male gland (13*). See
the Piston Packing Stack Detail in Fig. 7.
NOTE: If your pump uses an optional packing configuration, or you want to convert the pump to a different
packing material, see page 20.
3. Place the flats of the piston seat housing (16) in a
vise. Place the ball (11*) on the housing. Screw the
piston ball housing (10) onto the piston seat housing hand tight, then torque to 386–407 N.m
(285–300 ft-lb). See Fig. 6.
4. For standard displacement pump 237514, lubricate
the throat packings and place them in the outlet
housing (7) in the following order, with the lips of
the v-packings facing down: the male gland (6*),
four leather v-packings (3*), one PTFE v-packing
(5*), and the female gland (4*). See the Throat
Packing Stack Detail in Fig. 7.
NOTE: If your pump uses an optional packing configuration, or you want to convert the pump to a different
packing material, see page 20.
5. Install the packing nut (2) loosely into the outlet
housing (7).
16
308360
6. Lubricate the piston packings. Slide the displacement rod (1) and piston assembly down into the
cylinder (9). The cylinder is symmetrical, so either
end may face up. Use a rubber mallet to drive the
rod into the cylinder, until the piston seat housing
(16) is near the bottom of the cylinder.
7. Install the seal (8*) on the top of the cylinder (9).
Lubricate the seal and the top threads of the cylinder.
8. Place the outlet housing (7) in a vise, as shown in
Fig. 5. Slide the displacement rod (1) up into the
outlet housing, then screw the cylinder (9) into the
outlet housing handtight. The threads will engage
easily until the seal (8*) contacts the sealing surface of the outlet housing. The top of the rod will
protrude from the packing nut (2).
9. Install the seal (8*) on the bottom of the cylinder
(9). Lubricate the seal and the threads of the cylinder. With the beveled ball stop surfaces (S) facing down (see Fig. 7), screw the intake housing
(18) onto the cylinder handtight. The threads will
engage easily until the seal contacts the sealing
surface of the intake housing.
10. Install the seal (8*) on the intake valve (19). Lubricate the seal and the threads of the intake valve.
Place the intake ball (17*) in the intake housing
(18), then screw the intake valve into the intake
housing handtight. The threads will engage easily
until the seal contacts the sealing surface of the
intake housing.
11. Using a pipe wrench, torque the intake housing
(18) to 325–353 N.m (240–260 ft-lb). This will
torque both cylinder joints (A and B). See Fig. 5.
12. Using a pipe wrench, torque the intake valve (19)
to 190–217 N.m (140–150 ft-lb). See Fig. 5.
13. Torque the packing nut (2) to 136–149 N.m
(100–110 ft-lb).
14. Reconnect the displacement pump to the air motor
as explained on page 12.
Service
1
Torque to 136–149 N.m (100–110 ft-lb).
2
Torque to 325–353 N.m (240–260 ft-lb).
3
Torque to 386–407 N.m (285–300 ft-lb).
4
Lubricate.
2
5
Lips face up.
1
6
Lips face down.
7
See Throat Packing Detail at left.
8
See Piston Packing Detail at left.
9
Torque to 190–217 N.m (140–160 ft-lb).
1
7
Throat Packing Stack Detail
(Displacement Pump 237515 Shown;
see page 20 for options.)
7
T
2 (Ref)
*4
6
4
*3
*6
5*
6
4
4
*8
B
7 (Ref)
3
10
*11
F
Piston Packing Stack Detail
(Displacement Pump 237515 Shown;
see page 20 for options.)
9
E
18
10 (Ref)
8
9 (Ref)
P
2
16
16 (Ref)
3
A
*13
5
4
*12
14*
5
*15
17*
4
4
D
*8
18 (Ref)
*8 (Ref)
19
9
S
03634
Fig. 7
308360
17
Parts
Part No. 237516 Pump, Series A
21:1 Ratio, with Bulldog Air Motor
Part No. 237517 Pump, Series A
13:1 Ratio, with Senator Air Motor
102Y
102Y
101
101
107{
{105
107{
106{
{105
106{
110{
110{
109
{108
109
{108
{ These parts are included in
{ These parts are included in
Connection Kit 235417.
For applications requiring
stainless steel tie rods, order
Connection Kit 235418.
Connection Kit 235417.
For applications requiring
stainless steel tie rods, order
Connection Kit 235418.
04142
Ref.
No.
Part No.
Description
101
208356
AIR MOTOR, Bulldog
See 307–049 for parts
LABEL, warning
ROD, tie; 224 mm (8.82”)
shoulder to shoulder
NUT, coupling
COLLAR, coupling
NUT, hex; M16 x 2.0
PUMP, displacement
See page 19 for parts
WRENCH, spanner
102Y 176529
105{ 190000
106{
107{
108{
109
186925
184129
106166
237514
110{
112887
Qty.
1
1
3
1
2
3
1
1
Y Replacement Danger and Warning labels, tags and cards
are available at no cost.
18
308360
04141
Ref.
No.
Part No.
Description
101
217540
AIR MOTOR, Senator
See 307–592 for parts
LABEL, warning
ROD, tie; 224 mm (8.82”)
shoulder to shoulder
NUT, coupling
COLLAR, coupling
NUT, hex; M16 x 2.0
PUMP, displacement
See page 19 for parts
WRENCH, spanner
102Y 176529
105{ 190000
106{
107{
108{
109
186925
184129
106166
237514
110{
112887
Qty.
1
1
3
1
2
3
1
1
Y Replacement Danger and Warning labels, tags and cards
are available at no cost.
Parts
NOTE: The parts listed on this page are common to all displacement pumps covered in this manual. Refer to page 20
for the different packing configurations available.
* These parts are included in Repair Kit 237178, which may
be purchased separately for standard Displacement
Pump 237514. See page 20. They are also included in
Optional Kits 237179, 237180, and 237713.
Y Replacement Danger and Warning labels, tags and cards
are available at no cost.
Ref
No.
Part
No.
1
2
7
8*
9
10
11*
184487
236582
237186
109499
184540
189409
102972
16
222951
17*
108001
18
19
189396
236588
22
24Y
25Y
101748
172477
172479
Description
Qty
ROD, displacement; stainless steel
PACKING NUT; stainless steel
HOUSING, outlet; stainless steel
SEAL; PTFE r
CYLINDER; stainless steel
HOUSING, ball, piston; stainless steel
BALL, piston; stainless steel;
0.875” (22.2 mm) dia.
HOUSING, seat, piston valve;
stainless steel w/tungsten carbide seat
BALL, intake; stainless steel;
1.5” (38.1 mm) dia.
HOUSING, intake; stainless steel
VALVE, intake; stainless steel
w/tungsten carbide seat
PLUG, pipe, socket hd; 3/8 npt
TAG, warning (not shown)
TAG, warning (not shown)
1
1
1
3
1
1
1
1
1
1
1
1
1
1
2
10
Throat
Packing
Stack
(see page 20)
7
11*
22
Piston
Packing
Stack
(see page 20)
16
8*
1
18
*8
8*
17*
9
19
03630
308360
19
Packing Kits
Leather Packing Kit 237178, for Standard Displacement Pump 237514, Series A
Ref
No.
Part
No.
Description
3*
4*
5*
6*
12*
13*
14*
15*
184309
184179
109309
184229
184310
184230
109310
184180
V-PACKING, throat; leather
GLAND, throat, female; stainless steel
V-PACKING, throat; PTFE r
GLAND, throat, male; stainless steel
V-PACKING, piston; leather
GLAND, piston, male; stainless steel
V-PACKING, piston; PTFE r
GLAND, piston, female; stainless steel
THROAT PACKINGS:
LIPS FACE DOWN
Qty
4
1
1
1
4
1
1
1
PISTON PACKINGS:
LIPS FACE UP
*4
*13
5*
*3
*12
*6
*15
14*
LUBRICATE PACKINGS
0805
0806
* Kit also includes items 8, 11, and 17 (see page 19).
UHMWPE and Leather Packing Kit 237180, for Optional Displacement Pump 237515, Series A
Ref
No.
Part
No.
Description
3*
4*
5*
6*
12*
13*
14*
15*
184309
184179
109259
184229
184310
184230
109260
184180
V-PACKING, throat; leather
GLAND, throat, female; stainless steel
V-PACKING, throat; UHMWPE
GLAND, throat, male; stainless steel
V-PACKING, piston; leather
GLAND, piston, male; stainless steel
V-PACKING, piston; UHMWPE
GLAND, piston, female; stainless steel
THROAT PACKINGS:
LIPS FACE DOWN
Qty
2
1
3
1
2
1
3
1
PISTON PACKINGS:
LIPS FACE UP
*4
*13
*5
3* *14
*6
*15
12*
LUBRICATE PACKINGS
0805
0806
* Kit also includes items 8, 11, and 17 (see page 19).
PTFErPacking Kit 237179, for Optional Displacement Pump 236490, Series A
Ref
No.
Part
No.
Description
4*
5*
6*
13*
14*
15*
184179
109309
184229
184230
109310
184180
GLAND, throat, female; stainless steel
V-PACKING, throat; PTFE r
GLAND, throat, male; stainless steel
GLAND, piston, male; stainless steel
V-PACKING, piston; PTFE r
GLAND, piston, female; stainless steel
THROAT PACKINGS:
LIPS FACE DOWN
Qty
1
5
1
1
5
1
PISTON PACKINGS:
LIPS FACE UP
*4
*13
*5
*14
*6
*15
LUBRICATE PACKINGS
* Kit also includes items 8, 11, and 17 (see page 19).
0805
0806
UHMWPE and PTFErPacking Kit 237713 (Optional)
Ref
No.
Part
No.
Description
3*
4*
5*
6*
12*
13*
14*
15*
109309
184179
109259
184229
109310
184230
109260
184180
V-PACKING, throat; PTFE r
GLAND, throat, female; stainless steel
V-PACKING, throat; UHMWPE
GLAND, throat, male; stainless steel
V-PACKING, piston; PTFE r
GLAND, piston, male; stainless steel
V-PACKING, piston; UHMWPE
GLAND, piston, female; stainless steel
*
20
Kit also includes items 8, 11, and 17 (see page 19).
308360
THROAT PACKINGS:
LIPS FACE DOWN
Qty
2
1
3
1
2
1
3
1
PISTON PACKINGS:
LIPS FACE UP
*4
*13
*5
3* *14
*6
*15
LUBRICATE PACKINGS
12*
0805
0806
Technical Data
(Model 237516 Bulldog Pump)
WARNING
Be sure that all fluids and solvents used are chemically compatible with the
Wetted Parts listed below. Always read the manufacturer’s literature before using fluid or solvent in this pump.
Ratio . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21:1
Maximum fluid working pressure . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 145 bar (2100 psi)
Maximum air input pressure . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7 bar (100 psi)
Pump cycles per 3.8 liters (1 gal.) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12.5
Fluid flow at 60 cycles/min . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17.4 liters/min (4.6 gpm)
Air motor piston effective area . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 248 cm (38 in. )
Stroke length . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 120 mm (4.75 in.)
Displacement pump effective area . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12 cm (1.86 in. )
Maximum pump operating temperature . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 82 C (180 F)
* Noise level at 100 psi, 25 cycles/min . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 94 dBa
* Sound power level at 100 psi, 25 cycles/min . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 109 dBa
Air inlet size . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3/4 npsm(f)
Fluid inlet size . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2” npt(f)
Fluid outlet size . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1” npt(f)
Weight . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . approx. 109 kg (240 lb)
Wetted parts . . . . . . . . . 316, 440 and 17–4 PH Grades of Stainless Steel; Tungsten Carbide;
PTFE; Glass-Filled PTFE; Leather
* Tested in accordance with ISO 3744.
KEY:
A
B
C
Fluid Outlet Pressure – Black Curves
Air Consumption – Gray Curves
7 bar (100 psi) Air Pressure
4.9 bar (70 psi) Air Pressure
2.8 bar (40 psi) Air Pressure
NOTE: Recommended pump speed for continuous operation
(to shaded area): 60 cpm
psi
bar
2500
175
2000
140
1500
105
12.5
25
cycles/min
37.5
50
150
4.20
B
100
2.80
A
C
B
500
35
gpm 0
liters/min
75 scfm
m#/min
250
7.00
200
5.60
A
1000
70
0
62.5
60
50
1.40
C
1
3.8
2
7.6
3
11.4
4
15.2
5
19.0
6
22.8
FLUID FLOW (NO. 10 WEIGHT OIL)
To find Fluid Outlet Pressure (bar/psi) at a specific fluid flow (lpm/gpm)
and operating air pressure (bar/psi):
1. Locate desired flow along bottom of chart.
2. Follow vertical line up to intersection with selected fluid outlet
pressure curve (black). Follow left to scale to read fluid outlet
pressure.
To find Pump Air Consumption (m /min or scfm) at a specific fluid flow
(lpm/gpm) and air pressure (bar/psi):
1. Locate desired flow along bottom of chart.
2. Read vertical line up to intersection with selected air consumption
curve (gray). Follow right to scale to read air consumption.
308360
21
Technical Data
(Model 237517 Senator Pump)
WARNING
Be sure that all fluids and solvents used are chemically compatible with the
Wetted Parts listed below. Always read the manufacturer’s literature before using fluid or solvent in this pump.
Ratio . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13:1
Maximum fluid working pressure . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 90 bar (1300 psi)
Maximum air input pressure . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7 bar (100 psi)
Pump cycles per 3.8 liters (1 gal.) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12.5
Fluid flow at 60 cycles/min . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17.4 liters/min (4.6 gpm)
Air motor piston effective area . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 154 cm (24 in. )
Stroke length . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 120 mm (4.75 in.)
Displacement pump effective area . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12 cm (1.86 in. )
Maximum pump operating temperature . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 82 C (180 F)
* Noise level at 100 psi, 25 cycles/min . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 93 dBa
* Sound power level at 100 psi, 25 cycles/min . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 108 dBa
Air inlet size . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3/4 npsm(f)
Fluid inlet size . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2” npt(f)
Fluid outlet size . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1” npt(f)
Weight . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . approx. 109 kg (240 lb)
Wetted parts . . . . . . . . . 316, 440 and 17–4 PH Grades of Stainless Steel; Tungsten Carbide;
PTFE; Glass-Filled PTFE; Leather
* Tested in accordance with ISO 3744.
KEY:
A
B
C
Fluid Outlet Pressure – Black Curves
Air Consumption – Gray Curves
7 bar (100 psi) Air Pressure
4.9 bar (70 psi) Air Pressure
2.8 bar (40 psi) Air Pressure
NOTE: Recommended pump speed for continuous operation
(to shaded area): 60 cpm
psi
bar
1500
105
1000
70
12.5
25
cycles/min
37.5
50
62.5
60
75 scfm
m#/min
150
4.20
A
100
2.80
B
500
35
A
50
1.40
B
C
C
0
gpm 0
liters/min
1
3.8
2
7.6
3
11.4
4
15.2
5
19.0
6
22.8
FLUID FLOW (NO. 10 WEIGHT OIL)
To find Fluid Outlet Pressure (bar/psi) at a specific fluid flow (lpm/gpm)
and operating air pressure (bar/psi):
1. Locate desired flow along bottom of chart.
2. Follow vertical line up to intersection with selected fluid outlet
pressure curve (black). Follow left to scale to read fluid outlet
pressure.
22
308360
To find Pump Air Consumption (m /min or scfm) at a specific fluid flow
(lpm/gpm) and air pressure (bar/psi):
1. Locate desired flow along bottom of chart.
2. Read vertical line up to intersection with selected air consumption
curve (gray). Follow right to scale to read air consumption.
Dimensions
Mounting Hole
Layout
Model 237516 Shown
94.28 mm
(3.712”)
G
101.6 mm
(4.0”)
94.28 mm
(3.712”)
C
50.8 mm
(2.0”)
A
Three M16 x
2.0
Holes
11.1 mm
(0.437”)
DIA (4)
88 mm
(3.464”)
0653
D
B
F
E
04143
Pump Model
A
B
C
D
E
F
G
237516
1134 mm
(44.65 in.)
590 mm
(23.23 in.)
544 mm
(21.42 in.)
257 mm
(10.12 in.)
2 in. npt(f)
1 in. npt(f)
3/4 npsm(f)
237517
1138 mm
(44.80 in.)
590 mm
(23.23 in.)
548 mm
(21.57 in.)
257 mm
(10.12 in.)
2 in. npt(f)
1 in. npt(f)
3/4 npsm(f)
308360
23
Graco Standard Warranty
Graco warrants all equipment manufactured by Graco and bearing its name to be free from defects in material and workmanship on the
date of sale by an authorized Graco distributor to the original purchaser for use. With the exception of any special, extended, or limited
warranty published by Graco, Graco will, for a period of twelve months from the date of sale, repair or replace any part of the equipment
determined by Graco to be defective. This warranty applies only when the equipment is installed, operated and maintained in accordance with Graco’s written recommendations.
This warranty does not cover, and Graco shall not be liable for general wear and tear, or any malfunction, damage or wear caused by
faulty installation, misapplication, abrasion, corrosion, inadequate or improper maintenance, negligence, accident, tampering, or substitution of non–Graco component parts. Nor shall Graco be liable for malfunction, damage or wear caused by the incompatibility of
Graco equipment with structures, accessories, equipment or materials not supplied by Graco, or the improper design, manufacture,
installation, operation or maintenance of structures, accessories, equipment or materials not supplied by Graco.
This warranty is conditioned upon the prepaid return of the equipment claimed to be defective to an authorized Graco distributor for
verification of the claimed defect. If the claimed defect is verified, Graco will repair or replace free of charge any defective parts. The
equipment will be returned to the original purchaser transportation prepaid. If inspection of the equipment does not disclose any defect
in material or workmanship, repairs will be made at a reasonable charge, which charges may include the costs of parts, labor, and
transportation.
THIS WARRANTY IS EXCLUSIVE, AND IS IN LIEU OF ANY OTHER WARRANTIES, EXPRESS OR IMPLIED, INCLUDING BUT
NOT LIMITED TO WARRANTY OF MERCHANTABILITY OR WARRANTY OF FITNESS FOR A PARTICULAR PURPOSE.
Graco’s sole obligation and buyer’s sole remedy for any breach of warranty shall be as set forth above. The buyer agrees that no other
remedy (including, but not limited to, incidental or consequential damages for lost profits, lost sales, injury to person or property, or any
other incidental or consequential loss) shall be available. Any action for breach of warranty must be brought within two (2) years of the
date of sale.
Graco makes no warranty, and disclaims all implied warranties of merchantability and fitness for a particular purpose in connection
with accessories, equipment, materials or components sold but not manufactured by Graco. These items sold, but not manufactured
by Graco (such as electric motors, switches, hose, etc.), are subject to the warranty, if any, of their manufacturer. Graco will provide
purchaser with reasonable assistance in making any claim for breach of these warranties.
In no event will Graco be liable for indirect, incidental, special or consequential damages resulting from Graco supplying equipment
hereunder, or the furnishing, performance, or use of any products or other goods sold hereto, whether due to a breach of contract,
breach of warranty, the negligence of Graco, or otherwise.
FOR GRACO CANADA CUSTOMERS
The parties acknowledge that they have required that the present document, as well as all documents, notices and legal proceedings
entered into, given or instituted pursuant hereto or relating directly or indirectly hereto, be drawn up in English. Les parties reconnaissent avoir convenu que la rédaction du présente document sera en Anglais, ainsi que tous documents, avis et procédures judiciaires
exécutés, donnés ou intentés à la suite de ou en rapport, directement ou indirectement, avec les procedures concernées.
Graco Information
TO PLACE AN ORDER, contact your Graco distributor, or call one of the following numbers
to identify the distributor closest to you:
1–800–367–4023 Toll Free
612–623–6921
612–378–3505 Fax
All written and visual data contained in this document reflects the latest product information available at the time of publication.
Graco reserves the right to make changes at any time without notice.
Sales Offices: Minneapolis, Detroit
International Offices: Belgium, Korea, Hong Kong, Japan
www.graco.com
PRINTED IN USA 308360 06/1995, Revised 02/2003
24
308360
Download PDF
Similar pages