Installation Instructions

Installation
Instructions
6008.90X
VENETIAN™
DECK MOUNT BATH FILLER
Thank you for selecting American-Standard...
the benchmark of fine quality for over 100 years.
To ensure that your installation proceeds smoothly-please read these instructions carefully before you begin.
Certified to comply with ANSI A112.18.1M
M965014
To ensure that your installation proceeds smoothly-please read these instructions carefully before you begin.
Recommended Tools
ROUGHING-IN DIMENSIONS
6-1/2" to 12"
(165mm to 305mm)
7-1/2"
(191mm)
2" D.
(51mm) D.
2-9/16" D.
(66mm) D.
3"
(76mm)
Flat Blade Screwdriver
Tubing Cutter
8-3/16"
(211mm)
7-7/8"
(200mm)
2-1/16" D.
(52mm) D.
5"
(126mm)
MOUNTING
SURFACE
Adjustable Wrench
1-1/8 D.
*Wrench
3'
(76mm)
1-1/2 MAX.
(38mm) MAX.
1-3/16" MAX.
(30mm) MAX.
Channel Locks
1
SPOUT ASSEMBLY
CAUTION
3/4-14 MALE
N.P.T. INLETS
Turn off hot and cold water
supplies before beginning.
Install RUBBER RING (1) into recess of spout base.
Insert SPOUT SHANK (2) through center hole of MOUNTING LEDGE.
Make sure that the RUBBER RING (1) is properly seated in RECESS
of SPOUT BASE.
Assemble RUBBER WASHER (3) and BRASS WASHER (4) onto
SHANK (2). From underside of ledge secure SPOUT (6) into position
with LOCKNUT (5).
2
1-3/16 D.
(30mm) D.
(C)
(H)
*Hex key
*Supplied with Fitting
12 MAX.
(305mm)
1-1/16 D.
(27mm) D.
PREPARE TUBE AND TEE ASSEMBLY
Prepare TUBE and TEE ASSEMBLY (1) to fit center to center
VALVE (2) location (between 6-1/2" and 12"). If necessary,
cut and/or bend TUBING carefully. Make sure tube bend is
close to the TEE (1) so that it will not effect the compression
joint at the VALVE CONNECTION.
Remove COUPLING NUT (3) and FERRULE (4) from each
VALVE (2) and slide onto TUBING (5).
4
3
1
5
3
6-1/2" to 12"
(165mm to 305mm)
4
6
2
RECESS
1
MOUNTING
SURFACE
MOUNTING
SURFACE
3
4
5
2
NOTE
VALVE inlet is
3/4-inch NPT male.
3
VALVE ASSEMBLY
Install LOCKNUTS (1) and RUBBER WASHERS (2) onto valve shanks.
11
Push TUBING (3) ends into VALVE (4) side outlets. Insert VALVES (4)
into mounting holes from underside of ledge.
Press TEE (5) onto SPOUT SHANK (6) making certain that the O-RING (7) is
properly seated on SHANK (6). Push COUPLING (8) into TEE (5) and attach to
SPOUT SHANK (6) and tighten using a 10mm (3/8'') hex wrench. Tighten
COUPLING (8) using a 10mm (3/8") Hex wrench. (FOR 2064.900). Use
COUPLING (8a) for fitting less spray.
Thread of VALVE BODY (4) should extend at least 5/16 inch above MOUNTING
SURFACE (11). If necessary, adjust LOCKNUT (1).
9
10
9
Place RUBBER RING (10) into ESCUTCHEON ADAPTERS (9) and thread onto
valves until snug against internal stop.
Tighten LOCKNUT (1) with WRENCH supplied to secure VALVE (4) position.
10
4
Slide FERRULE (12) and COUPLING NUT (13) to outlet of VALVE (4) and tighten
COUPLING NUT (13) firmly.
7
12
Connect HOT water supply to inlet of left VALVE and COLD water supply to inlet of
right VALVE using appropriate connector.
10
5/16'' MIN.
4
9
4
6
13
HOT
11
12
3
MOUNTING
SURFACE
4
5
8
8a
2
Wrench
MOUNTING
SURFACE
13
1
COLD
INSTALL HANDLES
Push ADAPTER (1) on VALVE STEM (2), so that the hole of the
ADAPTER (1) without a spline is facing up. Fig. A. Tighten
STEM SCREW (3) to secure ADAPTER (1).
THREAD ON
TO DECK
ADAPTER
4
Find correct position of LEVER HANDLE ASSEMBLY (4) by adjusting
male teeth on ADAPTER (1) to female teeth in HANDLE (4).
TOP
1
Thread LEVER HANDLE ASSEMBLY (4) onto DECK ADAPTER (5)
until snug against mounting surface.
3
Fig. A.
2
SPLINE END DOWN
5
5
SERVICE
REMOVE
HANDLE
To change direction of handle rotation,
proceed as follows:
Turn valve to OFF position. Unthread HANDLE BASE (1) from DECK
ADAPTER (2).
HANDLE
ASSEMBLY
Pull HANDLE ASSEMBLY off VALVE STEM (3).
Remove SPRING CLIP (4). Lift STOP WASHER (5), turn 90˚ and replace.
Replace SPRING CLIP (4).
90˚
Find correct position of HANDLE ASSEMBLY by adjusting male teeth on
VALVE STEM (3) to female teeth in HANDLE.
Thread HANDLE ASSEMBLY onto DECK ADAPTER (2) until snug against
mounting surface.
4
3
5
2
M965014
6
HANDSHOWER INSTALLATION (For 2064.901 only)
11
Drop SPRAY ESCUTCHEON (1) through the fourth hole of the tub ledge (12" max from SPOUT
center) with SPRAY ESCUTCHEON (1) directed towards tub center. Be sure RUBBER RING (2)
is properly seated in SPRAY ESCUTCHEON (1). Install RUBBER WASHER (3), BRASS WASHER (4)
and LOCKNUT (5) from underside of ledge.
9
Secure SPRAY ESCUTCHEON (1) by tightening LOCKNUT (5).
Install SEAL (9) and connect HOSE (10) to outlet nipple at the bottom of TEE (7). Tighten firmly.
6
Slip SHOWER HOSE (8) with COUPLING NUT through SPRAY
HOLDER (6) and SPRAY ESCUTCHEON (1). Note: SPRAY
HOLDER (6) must be seperate from ESCUTCHEON (1) to
pass HOSE (8) through ESCUTCHEON.(1)
Insert SEAL (9) into SHOWER HOSE (8). Connect HOSE (8)
to HOSE (10).
Install SEAL (9) and connect HAND SHOWER (11) to
SPRAY HOSE (8).
3
9
7
9
4
8
MAKE WATER SUPPLY CONNECTIONS
HAND
SHOWER
Connect HOT water supply to LEFT INLET
UNION (1) and COLD water supply to
RIGHT INLET UNION (2). Pipe connections
are 3/4" NPT. Use sealant or Teflon tape
on pipe connections.
Do not solder directly to valve body.
7A
TRANSFER KNOB
TEST INSTALLED FAUCET
COLD
With HANDLES in OFF position, turn on
WATER SUPPLIES and check all connections
for leaks.
Operate both HANDLES to flush water lines
thoroughly.
2
Turn handles "off" and replace HAND SHOWER.
3/4" NPT
HOT
1
Lift HAND SHOWER from HOLDER, direct spray
into tub. Lift TRANSFER KNOB to check HAND
SHOWER and HOSES for leaks.
8
2
5
10
When not in use, HANDSHOWER should be seated
in the HOLDER.
NOTE
7
1
3/4" X 3/4" NPT UNION
(NOT SUPPLIED)
3/4" NPT
IMPORTANT: It is strongly recommended that access be
provided for all enclosed mechanical parts to this system.
Before the bathroom is completely finished, you may
want to remove spout, handshower, and handles to
avoid damage during construction.
2
VIEW "A"
To remove handles, reverse steps in section 4.
To remove SPOUT (1), proceed as follows:
Unthread LIFT ROD KNOB (2) and remove.
Remove PLUG BUTTON (3) and remove SET SCREW (4) using
4mm hex wrench supplied.
Lift SPOUT (1) off SHANK (5) carefully and remove RUBBER
RING (6).
Unthread SHANK SLEEVE (7) and remove from SHANK (5).
Reverse sequence to re-install SPOUT (1). Be sure RUBBER
RING (6) is properly seated in its recess at the base of the
SPOUT (1). Make certain SET SCREW (4) is properly aligned
and tight so that SPOUT (1) is locked in place.
9
1
3
4
6
VIEW "A"
Hex wench
(supplied)
7
5
CARE INSTRUCTIONS:
DO: SIMPLY RINSE THE PRODUCT CLEAN WITH CLEAR WATER. DRY WITH A SOFT COTTON FLANNEL CLOTH.
DO NOT: DO NOT CLEAN THE PRODUCT WITH SOAPS, ACID, POLISH, ABRASIVES, HARSH CLEANERS, OR A
CLOTH WITH A COARSE SURFACE.
M965014
VENETIAN ™
DECK-MOUNT
BATH FILLER
MODEL NUMBER
6008.90X
M962904-YYY0A
SPOUT KIT (6008.901)
M962903-YYY0A
SPOUT KIT (6008.900)
A922388-YYY0A
STREAM
STRAIGHTENER
M911903-0070A
SEAL
Replace the "YYY" with
appropriate finish code
M962591-YYY0A
HANDLE
ASSEMBLY
CHROME
SATIN NICKEL
002
295
M962902-YYY0A
TRANSFER
ROD ASSEMBLY
M950090-YYY0A
HAND SHOWER
M962592-YYY0A
DECK ADAPTER KIT
030275-0070A
SHANK SLEEVE KIT
030274-0070A
SHANK MOUNTING KIT
918555-0070A
HANDLE SCREW
918049-0070A
HANDLE ADAPTER
012668-0070A
SHANK KIT
994053-0070A
VALVE
028664-YYY0A
HAND SHOWER
HOLDER
M961634-0070A
VALVE
MOUNTING
KIT
028679-0070A
TUBE & TEE
ASSEMBLY
028699-0070A
COUPLING (FOR TRANSFER)
028698-0070A
COUPLING
012078-0070A
VALVE COUPLING KIT
HOT LINE FOR HELP
For toll-free information and answers to your questions, call:
1 (800) 442-1902
Weekdays 8:00 a.m. to 6:00 p.m. EST
IN CANADA 1-800-387-0369 (TORONTO 1-905-306-1093)
Weekdays 8:00 a.m. to 7:00 p.m. EST
A952849-0070A
CHECK VALVE
028667-0020A
HAND SHOWER HOSE
051343-0070A
HOSE KIT
IN MEXICO 01-800-839-12-00
Pr o d u c t n a me s liste d he re in are trademarks of American Standard Inc.
© AS Am e rica, I nc. 2009
M965014
Download PDF
Similar pages