[密级]机密
技术要求:
1.四色印刷
2.第一页为封面和封底
3.规格为A5,按A5规格输出菲林和印刷
英文用户手册
DTC36610W(3606)
BEKO土耳其
标记 处数 分区 更改文件号 签 名
会 签
设 计
审批
认 证
校 对
日期
1
日期
比例
阶段标记
REV. 03
1:1
数
量
共 1 张
第 1 张
6720601341
80G双胶
佛山市顺德区美的
洗涤电器制造有限公司
Dishwasher
User’s Manual
DTC36610W
EN
www.beko.com.tr
For detailed operating method read the corresponding content on the instruction manual.
Switch on the appliance
Fill the detergent dispenser
Touch the Power switch button to switch on the appliance, Open the door.
With each wash cycle.
Compartment
For programmes with pre-wash only.
C
(Follow the user instructions!)
Check the rinse aid level
Check the regeneration
salt level
Load the baskets
Select a programme
Running the dishwasher
Changing the programme
Add forgotten dishes in the
dishwasher.
If the appliance is switched
off during a wash cycle.
Switch off the appliance
Turn off the water tap,
unload the baskets
Electric indicator on control panel (if provided).
(On models with water softener system only.)
Electric indicator on control panel (if provided).
If there is no salt warning light in the control panel
(for some models), you can estimate when to fill the salt into
the softener by the number of cycles the dishwasher has run.
Scrape off any large amount of leftover food. Soften remnants of burnt food in pans,
then load the baskets. Refer to the dishwasher loading instructions.
Close the door,Touch the programme button until the selected programme lights up.
( See the section entitled“Operation instruction”)
Turn on the water tap and touch the Start/Pause button. The machine will start working
after about 10 seconds.
1. A running cycle can only be modified if it has been running for a short time. Otherwise the detergent
may have already been released and the water already drained. If this is the case, the detergent
dispenser must be refilled.
2. Press the Start/Pause button ,than press the program button more than 3 seconds to cancel the
running programme.
3. Select a new programme.
4. Restart the dishwasher.
1.Touch the start/pause button to stop the machine.
2.Open the door.
3.Add the forgotten dishes.
4.Close the door, then touch the start/pause button, the dishwasher will
start running again after 10 seconds.
Open the door carefully.
Hot steam may escape
when the door is opened!
If the appliance is switched off during a wash cycle, when switched
on again, please re-select the washing cycle and operate the dishwasher
according to the original Power-on state ).
When the working cycle has finished, the buzzer of the dishwasher will sound 8 times, then stop.
Turn off the appliance using the Power button.
Since the appliance is standing by, it will power off automaticly after 30 minutes without any operation.
Warning: wait a few minutes (about 15 minutes) before unloading the dishwasher to avoid handling
the dishes and utensils while they are still hot and more susceptible to break.
They will also dry better.Unload the appliance, starting from the lower basket.
Manufactured by Arcelik A.S.Karaagac Cd.No:2, 34445 Sutluce,Beyoglu,Istanbul,Turkey
Dear Customer,
Please carefully read this manual before using the
dishwasher, it will help you to use and maintain the
dishwasher properly.
Keep it to refer to it at a later date.
Pass it on to any subsequent owner of the appliance.
This manual contains sections on safety Instructions,
Operating Instructions, Installation Instructions and
Troubleshooting Tips, etc.
Control Panel...................................................3
Dishwasher Features.................................... ...3
A、Loading the Salt into the Softener.................4
B、Fill the Rinse Aid Dispenser.........................5
C、Function of Detergent .................................6
Attention before or after loading the Dishwasher
Baskets..........................................................9
Loading the Basket...........................................9
Cutlery Basket..............................................10
To review the section on troubleshooting Tips
will help you to solve some common problems
by yourself .
If you can not solve the problems by yourself ,
please ask for the help of professional technicians.
Wash Cycle Table...........................................11
Turning on the Appliance................................11
Change the Programme.............. .... ................12
At the end of the Wash Cycle...........................12
Filtering System.............................................13
Caring for the Dishwasher..................... . .........14
The manufacturer, following a policy of constant
development and updating of the product, may
make modifications without giving prior notice.
Positioning the Appliance................... .. ..........16
About Power Connection........................ . .......16
Water Connection.................................. . .......16
Connection of Drain Hoses..................... . .......17
Start of dishwasher............................. .. .. .. ......18
This user manual shall also be got from the
manufacturer or responsible vendor.
Before calling for service........................... . .....19
Error codes.................................... . ..............20
Technical information.............................. .. .....21
When using your dishwasher,
follow the precautions listed below:
This appliance is intended to be used in household
and similar applications such as:
-staff kitchen areas in shops, offices and other
working environments;
-farm houses;
-by clients in hotels, motels and other residential type
environments;
-bed and breakfast type environments.
This appliance can be used by children aged from 8
years and above and persons with reduced physical,
sensory or mental capabilities or lack of experience
and knowledge if they have been given supervision
or instruction concerning use of the appliance in a
safe way and understand the hazards involved.
Children shall not play with the appliance. Cleaning
and user maintenance shall not be made by children
without supervision.(For EN60335-1 )
This appliance is not intended for use by persons
(including children )with reduced physical, sensory
or mental capabilities, or lack of experience and
knowledge ,unless they have been given supervision
or instruction concerning use of the appliance by a
person responsible for their safety.(For IEC60335-1 )
This appliance is for indoor use only, for household
use only.
To protect against the risk of electrical shock, do not
immerse the unit, cord or plug in water or other liquid.
Please unplug before cleaning and maintenance the
appliance .
Use a soft cloth moisten with mild soap, and then use
a dry cloth to wipe it again.
This appliance must be earthed. In the event of a
malfunction or breakdown, grounding will reduce the risk
of an electric shock by providing a path of least
resistance of electric current. This appliance is equipped
with a cord having an equipment-earthing conductor
and a earthing plug.
The plug must be plugged into an appropriate outlet that
is installed and earthed in accordance with all local
codes and ordinances.
Improper connection of the equipment-earthing
conductor can result in the risk of an electric shock.
Check with a qualified electrician or service
representative if you are in doubt whether the appliance
is properly grounded.
Do not modify the plug provided with the appliance;
If it does not fit the outlet.
Have a proper outlet installed by a qualified electrician.
Do not abuse, sit on, or stand on the door or dish rack of
the dishwasher.
Do not operate your dishwasher unless all enclosure
panels are properly in place.
Open the door very carefully if the dishwasher is
operating, there is a risk of water squirting out.
Do not place any heavy objects on or stand on the door
when it is open. The appliance could tip forward.
When loading items to be washed:
1) Locate sharp items so that they are not likely to
damage the door seal;
2) Warning: Knives and other utensils with sharp points
must be loaded in the basket with their points down or
placed in a horizontal position.
Check that the detergent comparment is empty after
completion of the wash cycle.
Do not wash plastic items unless they are marked
dishwasher safe or the equivalent.
For plastic items not so marked, check the manufacturer's
recommendations.
Use only detergent and rinse additives designed for
an automatic dishwasher.
Never use soap, laundry detergent, or hand washing
detergent in your dishwasher.
Children should be supervised to ensure that they do not
play with the appliance.
The door should not be left open, since this could increase
the risk of tripping.
If the supply cord is damaged, it must be replaced by the
manufacturer or its service agent or a similarly qualified
person in order to avoid a hazard.
During installation, the power supply must not be
excessively or dangerously bent or flattened.
Do not tamper with controls.
The appliance is to be connected to the water mains using
new hose sets and that old hose-sets should not be reused.
The maximum number of place settings to be washed
is 6.
The maximum permissible inlet water pressure is 1MPa.
The minimum permissible inlet water pressure is 0.04MPa.
Safety and Environment Instructions
1170-1380W
0.04-1.00MPa
To get the best performance from your dishwasher, read all operating instructions
before using it for the first time.
2
4
1
Program indicator light:
--Intensive
--Glass
--Normal
--90min
--ECO
--Rapid
3
Program Selector: Press the button to select
wash cycles
4
Delay Button : To press. the button to delay.
7
3
4
7 4
4
6
5
Start/Pause Button: Press this button to start
or pause the dishwasher .
Power Button: To turn on/off the power supply.
2
8
4
6
Salt Warning Light : To be on when the softener
needs to be refilled.
7
Rinse Aid Warning Light : To be on when the
rinse aid dispenser needs to be refilled.
8
Display screen: to show the reminding time
and the state(running state, delay time etc ) .
8
Front view
Back View
2
4
1
5
6
9
3
1
Salt Container
3
Cutlery Basket
5
Rinse Aid Dispenser
7
Cup Shelf
2
Detergent Dispenser
4
Filter assembly
6
Spray Arms
8
Basket
3
10
9
Inlet pipe connector
10 Drain pipe connector
If your model have no water softener, you may skip this section.
Always use salt intended for use with dishwasher.
The salt container is located beneath the basket and should be filled as follows:
Attention!
Only use salt specifically designed for use in dishwashers! All other types of
salt not specifically designed for use in a dishwasher, especially table salt, will
damage the water softener. in case of damages caused by the use of unsuitable
salt the manufacturer does not give any warranty nor is liable for any caused
damages.
Only fill with salt just before starting one of the complete washing programmes.
This will prevent any grains of salt or salty water, which may have been split,
remaining of the bottom of the machine for any period of time, which may cause
corrosion.
A Remove the basket and then unscrew and remove the cap from the salt container.
B Before first wash, add 1lt. of water in the salt container of your machine.
C Place the end of the funnel (supplied) into the hole and introduce about 1kg of salt.
It is normal for a small amount of water to come out of the salt container.
D After filling the container , screw the cap tightly back clockwise.
E Usually, the salt warning light will be cease to be illuminated within 2-6 days after the salt container has been filled with
salt.
F Immediately after filling the salt into the salt container, a washing programme should be started
Otherwise filter system, pump or other important parts of the machine may be damaged by salty
water. It is out of warranty.
1. The salt container must only be refilled when the salt warning light in the control panel comes on.
Depending on how fully the salt dissolves, the salt warning light may still be on even though the
salt container is filled.
If there is no salt warning light in the control panel (For some Models),you can judge when to load
the salt into the softener by the cycles that the dishwasher had run.
2. If there are spills of the salt, a soak or a rapid program should be run to remove the excess salt.
Adjusting Salt Consumption
Step 1: Enter the status of salt adjustment
Close the door, within 60 seconds after power on, Touch Start/Reset button and hold for 5 seconds,
the machine will enter setting mode.
4
Step 2: select a certain level of salt consumption
Touch the Start/pause button to select the proper set according to your local environment,
the sets will change in the following sequence: H1->H2->H3->H4->H5->H6;
Step 3: Exit the status of salt adjustment
Without any operation in five seconds, the machine will exit from set mode, the machine is into standby status
There are 6 levels of salt consumption in all.It is recommended to select the level according to below table:
Water Hardness level
dH
1)
mmol/l
2)
Setting on the
water softener
0-5
0-0.9
1
6-11
1.0-2.0
2
12-17
2.1-3.0
3
18-22
3.1-4.0
4*
23-34
4.1-6.1
5
35-45
6.2-8.0
6
Digital display stalls
1) German degree of measurement for the water hardness
2) millimol, internationel unit for water hardness
*) factory setting
Contact your local water board for information on the hardness of your water supply.
Rinse Aid Dispenser
The rinse aid is released during the final rinse to prevent water from forming droplets on your dishes. That can leave
spots and streaks. It also improves drying by allowing water to sheet off the dishes. Your dishwasher is designed to
use liquid rinse aids. The rinse aid dispenser is located inside the door next to the detergent dispenser. To fill the
dispenser, open the cap and pour the rinse aid into the dispenser until the level indicator turns completely black.
The volume of the rinse aid container is about 110ml.
Function of Rinse Aid
Rinse aid is automatically added during the last rinse, ensuring thorough rinsing, and spot and streak free drying.
5
Function of Rinse Aid
Rinse aid is automatically added during the last rinse, ensuring thorough rinsing, and spot and streak free drying.
Attention!
Only use branded rinse aid for dishwasher. Never fill the rinse aid dispenser with any other substances
(e.g. Dishwasher cleaning agent, liquid detergent). This would damage the appliance.
When to Refill the Rinse Aid Dispenser
If there is no rinse-aid warning light in the control panel, you can judge the amount of rinse-aid by the color
of the optical level indicator " "located next to the cap. When the rinse-aid container is full, the whole
indicator will be dark .As the rinse-aid diminishes, the size of the dark dot decreases. You should never let
the rinse aid get below 1 / 4 full.
C (Rinse-Aid indicator)
As the rinse aid diminishes, the size of the black dot
on the rinse aid level indicator changes, as illustrated below.
Full
3 / 4 full
1 / 2 full
1 / 4 full - Should refill to eliminate spotting
Empty
1
2
3
To open the dispenser, turn the cap to the "open" (left) arrow and lift it out.
Pour the rinse aid into the dispenser, being careful not to overfill.
Replace the cap by inserting it aligned with "open" arrow and turning it to the closed (right) arrow.
Clean up any rinse aid split during filling with an absorbent cloth to avoid excessive foaming
during the next wash. Don't forget to replace the cap before you close dishwasher door.
Adjusting Rinse Aid Dispenser
The rinse aid dispenser has six or four settings. Always start with the dispenser
set on "4". If spots and poor drying are problems, increase the amount of rinse
aid dispensed by removing the dispenser lid and rotating the dial to "5". If the
dishes still are not drying properly or are spotted, adjust the dial to the next
higher number until your dishes are spot-free. The recommended setting is "4".
(Factory value is "4".)
Increase the dose if there are drops of water or lime spots on the dishes after washing.
Reduce it if there are sticky whitish stains on your dishes or a bluish film on glassware or
knife blades.
Detergents with its chemical ingredients are necessary to remove dirt, crush dirt and transport it out of the dishwasher.
Most of commercial quality detergents are suitable for this purpose.
6
Normally new pulverised detergent is without phosphate, thus he water softener function of
phosphate is not given. In this case we recommend to fill salt in the salt container even when
the hardness of water is only 6 °dH. If detergents without phosphate were used in case of hard water
often white spots appear at dishes and glasses. In this case please add more detergent to reach
better results. Detergents without chlorine do only bleach a little. Strong and coloured spots will not
removed completely. In this case please choose a program with higher temperature.
Concentrated Detergent
Based on their chemical composition, detergents can be split in two basic types:
Conventional, alkaline detergents with caustic components.
Low alkaline concentrated detergents with natural enzymes.
The use of Normal washing program in combination with concentrated detergent reduces
pollution and is good for your dishes.
Detergent Tablets
Detergent tablets of different brands dissolve at different speeds. For this reason some
detergent tablets cannot dissolve and develop their full cleaning power during short
Programs. Therefore please use long programs when using detergent tablets, to
ensure the complete removal of detergent residuals.
Detergent Dispenser
The dispenser must be refilled before the start of each wash cycle following the instructions
provided in the Wash Cycle Table . Your dishwasher uses less detergent and rinse aid then
conventional dishwasher. Generally, only one tablespoon of detergent is needed for
a normal wash load. More heavily soiled items need more detergent. Always add the
detergent just before starting the dishwasher, otherwise it could get damp and will not
dissolve properly.
Adding detergent to dispenser
If the lid is closed: push the latch to open.
Always add the detergent just before starting each wash cycle.
Only use branded detergent and rinse aid for dishwasher.
7
Dishwasher detergent is corrosive!
Take care to keep it out of reach of children.
Proper Use of Detergent
Only use detergent specifically made for use in dishwashers. Keep your detergent fresh and dry.
Don't put powder detergent into the dispenser until you're ready to wash dishes.
A
B
Fill in detergent dispenser
Fill the detergent dispenser with detergent.
The marking indicates the dosing levels, as
illustrated on right:
A
Location of main wash cycle detergent.
B
Location of pre-wash cycle detergent
Please observe the manufacturers dosing and storage
Recommendations as stated on the detergent packaging.
Close the lid and press until it locks in place.
If the dishes are heavily soiled, place an additional
detergent dose in the pre-wash detergent chamber. This detergent will take effect during the pre-wash phase.
You see information about the amount of detergent for the single program on the page9.
Please be aware that soiling levels and water hardness can effect wash results.
Please observe the manufacturer's recommendations on the detergent packaging.
Consider buying utensils which are identified as dishwasher-proof.
Use a mild detergent that is described as 'kind to dishes'. If necessary, seek further
information from detergent manufacturers.
For particular items, select a program with as low temperature as possible.
To prevent damage, do not take glass and cutlery out of the dishwasher immediately
after the program has ended.
Not suitable for use
Limited suitability
Cutlery with wooden, horn china or
mother-of-pearl handles.
Plastic items that are not heat resistant.
Older cutlery with glued parts that is not
temperature resistant.
Bonded cutlery items or dishes.
Pewter or copper items.
Crystal glass.
Steel items subject to rusting.
Wooden platters.
Items made from synthetic fibres.
Some types of glasses can become
dull after a large number of washes.
Silver and aluminium parts have a
tendency to discolour during washing.
Glazed patterns may fade if machine
washed frequently.
8
(For the best performance of the dishwasher, follow these loading guidelines.
Features and appearance of baskets and cutlery baskets may vary from your model.)
Scrape off any large food paritcles. Soften remnants of burnt food in pans
It is not necessary to rinse the dishes under running water.
Place objects in the dishwasher in following way:
1.Items such as cups, glasses, pots/pans, etc. are face downwards.
2.Curved items, or those with recesses, should be loaded at aslant so that water can run off.
3.All utensils are stacked securely and can not tip over.
4.All utensils are placed in the way that the spray arms can rotated freely during washing.
Very small items should not be washed in the dishwasher as they could easily fall out of the basket.
Load hollow items such as cups, glasses, pans etc. with the opening facing downwards so that
water cannot collect in the container or a deep base.
Dishes and items of cutlery must not lie inside one another, or cover each other.
To avoid damage to glasses, they must not be touched.
Long bladed knives stored in an upright position are a potential hazard!
Long and/or sharp items of cutlery such as carving knives must be positioned
horizontally in the basket.
Please do not overload your dishwasher. This is important for good results and for
reasonable energy consumption.
Position the dishes and cookware so that they will not get moved by the spray of water.
2
1
Cups
Medium serving bowl
3
4
Glasses
Saucers
5
6
Dish
Oval platter
7
8
Dinner plates
Soup plates
10
99
Dessert dishes
Cutlery basket
11
Serving spoons
9
Position the dishes and cookware so that they do not get moved by the spray of water.
1 Forks
2 Soup spoons
3 Dessert spoons
4 Teaspoons
5 Knives
6 Serving spoons
7 Gravy ladles
8 Serving forks
Do not let any item extend through bottom.
Always load sharp utensils with the sharp point down!
10
Intensive
Normal
(*EN 50242)
For heaviest soiled crockery,
and normally soiled pots、
pans、dishes etc with dried
on soiling.
Pre-wash ( 50℃)
Wash (70 ℃)
Rinse
Rinse
Rinse (70 ℃)
Drying
For normally soiled loads,
such as pots, plates,
glasses and lightly
soiled pans.
Pre-wash
Wash (60 ℃)
Rinse
Rinse (70 ℃)
Drying
This is standard programme,
it is suitable to clean normally
soiled tableware and it is the
most efficient programme in
terms of its combined energy
and water consumption for
that type of tableware.
Pre-wash
Wash (50 ℃)
Rinse
Rinse (70 ℃)
Drying
Glass
For lightly soiled loads,
such as glasses, crystal and
fine china.
Wash (45 ℃)
Rinse
Rinse (60 ℃)
Drying
90 min
For lightly soiled crockery
and glass.
Wash(65 ℃)
Rinse(70 ℃)
Drying
Rapid
Wash (40 ℃)
A shorter wash for lightly soiled Rinse
loads and quick wash.
Rinse (40 ℃)
3/15g
( 1 tablet)
140
0.9
10
3/15g
( 1 tablet)
120
0.7
8
3/15g
( 1 tablet )
180
0.61
6.5
18g
( 1 tablet )
75
0.5
7.0
18g
( 1 tablet )
90
0.65
7.0
30
0.23
6
15g
*EN 50242 : This programme is the test cycle. The information for comparability test
in accordance with EN 50242, as follows:
Capacity: 6 setting
Rinse aid setting: 6
The power consumption of off-mode is 0.45W
left-on mode is 0.49W
Starting a wash cycle...
Draw out the basket(see the section entitled “Loading the Dishwasher”).
Pour in the detergent (see the section entitled “Salt,
Detergent and Rinse Aid”).
Insert the plug into the socket. The power supply is 220-240
VAC 50 HZ, the specification of the socket is 10 A 250 VAC.
Make sure that the water supply is turned on to full pressure.
Touch the program button , the wash program will be changed as follows direction
ECO-> Glass->90 min->Rapid ->Intensive->Normal ;
If a program is selected, the response light will light. Then touch the
Start/Pause button, the dishwasher begins to start.
When you touch the Start/Pause button to pause during washing,
the program light will stop blinking and the dishwasher will mooing
every minute unless you touch the Start/Pause button to start.
11
Premise: You can modify the washing program, If the dishwasher just
worked for a short time. Otherwise, the detergent may have already been
released, and the appliance may have already drained the wash water. in this
case, the detergent dispenser must be refilled (see the section entitled
" Detergent " ).
Touch S tart/Pause Button to pause the machine when the door is closed ,Touch
Program Button more than three seconds the machine will be in stand by state ,
then you can change the program to the desired cycle setting (see the section
entitled " Starting a wash program" ).
The program lights show the status of the dishwasher:
a) One of the program lights on----------stand by or pause.
b) One of the program lights blinking----- running.
If you open the door during washing, the machine will pause. When you close the door
the machine will keep on working after 10 seconds.
Your model has broken remember function, the machine will go on to finish the selected
program after the power cut.
A forgotten dish can be added any time before the detergent cup opens.
4 Add forgotten dishes.
1 Touch the Start/Pause button.
2 Open the door a little to stop the washing.
5
Close the door.
the spray arms stop working,you can open the door
3 After
completely.
6
Touch the Start/Pause button, the dishwasher will run
after 10 seconds.
When the working cycle has finished, the buzzer of dishwasher will sound 8 seconds, then stop. Turn off
the appliance using the ON/OFF button, shut off the water supply and open the door of the dishwasher.
Wait a few minutes before unloading the dishwasher to avoid scald, the dishes and utensils
are still hot and more susceptible to breakage. They will also dry better.
Switch Off the Dishwasher
1.Switch off the dishwasher by pressing the ON/OFF button.
2.Turn off the water tap!
Open the door carefully.
Hot dishes are sensitive to knocks. The dishes should be allowed to cool down around 15 minutes
before removing from the appliance.
Open the dishwasher's door, leave it ajar and wait a few minutes before removing the dishes. In this way they
will be cooler and the drying will be improved.
Unloading the dishwasher
It is normal that the dishwasher is wet inside.
It is dangerous to open the door when washing,
because the hot water may scald you.
12
The filter prevent larger remnants of food or other objects from getting inside the pump.
The filter system consists of a coarse filter, a flat (Main filter)
and a micro filter (fine filter).
C
Main filter
A
Food and soil particles trapped by this filter are pulverized by a
special jet on the spray arm and washed down to drain.
B
Fine filter
B
This filter holds soil and food residues in the sump area and
prevents it from being redeposited on the dishes during a cycle.
A
Coarse filter
C
Larger items, such as pieces of bone or glass, that could block
the drain are trapped in the coarse filter. To remove the items
caught by this filter, gently squeeze the tap on the top of this
filter and lift it out.
Filter assembly
The filter efficiently removes food particles from the wash water, allowing it to be recycled during the cycle.
For best performance and results, the filter assembly must be cleaned regularly. For this reason, it is a good idea to
remove the larger food particles trapping in the filter after each wash cycle by rinsing the filter and cup under
running water. To remove the filter assembly, pull the cup handle in the upward direction.
Never run the dishwasher without the filters in place.
The dishwasher must never be used without the filters.
Improper replacement of the filter may reduce the performance level of the appliance
and damage dishes and utensils.
Step 1:Contrarotate the filter assembly(A,B and C),
then lift it all up.
C
B
A
Step 2: Lift B and C up from A;
C
B
Step 3: Separate B and C.
A
If do it from step1 to step 3, the filter system will be removed; while if do it from Step 3 to Step 1,
the filter system will be installed.
13
Notes:
- Inspect the filters for blocking after every time the dishwasher has been used.
- By unscrewing the coarse filter, you can remove the filter system.Remove any food remnants and
clean the filters under running water.
The entire filter assembly should be cleaned once a week.
Cleaning The Filter
To clean the coarse filter and the fine filter, use a cleaning brush. Reassemble the filter parts as shown in the figures
on the last page and reinsert the entire assembly in the dishwasher, positioning in its seat and pressing downward.
When cleaning the filters, don't knock on them. Otherwise, the filters could be
contorted and the performance of dishwasher could be decreased.
The control panel can be cleaned by using a lightly dampened cloth. After cleaning,make sure to dry it thoroughly.
For the exterior use a good appliance polish wax.
Never use sharp objects, scouring pads or harsh cleaners on any part of the dishwasher.
Cleaning The Door
To clean the edge around the door, you should use only a soft warm,
damp cloth. To avoid penetration of water into the door lock and
electrical components, do not use a spray cleaner of any kind.
Never use a spray cleaner to clean the door panel as it may damage the door lock
and electrical components.
Abrasive agents or some paper towel should not be used because of the risk of
scratching or leaving spots on the stainless steel surface.
Protect Against Freezing
please take frost protection measures on the dishwasher in winter. E ach time a fter washing cycles,
please operate as follows:
1. Cut off electrical power to the dishwasher.
2. Turn off the water supply and disconnect the water inlet pipe from the water valve.
3. Drain water from the inlet pipe and water valve (Use a pan to catch the water)
4. Reconnect the water inlet pipe to the water valve.
5. Remove the filter at the bottom of the tub and use a sponge to soak up water in the sump.
If your dishwasher cannot work because of the ice, please contact authorised service person.
14
Cleaning the Spray Arms
The spray arms can be easily removed for periodic cleaning
of the nozzles to prevent possible clogging. Wash them
under running water and carefully replace them in their seats,
checking that their rotary movement is in no way impeded.
Grasp the middle of the spray arm, pull it upwards to remove
it. Wash the arms under a jet of running water and replace it
carefully to its seat. After reassembly, check that the spray
arms rotate freely. Otherwise, check that they have been
installed correctly.
When not in use for a long time
After Every Wash
It is recommend that you run a wash cycle with the
dishwasher empty and then remove the plug from the
socket, turn off the water supply and leave the door of
the appliance slightly open. This will help the door
seals to last longer and prevent odours from forming
within the appliance.
After every wash, turn off the water supply to the
appliance and leave the door slightly open so that
moisture and odors are not trapped inside.
Remove the Plug
Before cleaning or performing maintenance, always
remove the plug from the socket.
Moving the Appliance
No Solvents or Abrasive Cleaning
To clean the exterior and rubber parts of the dishwasher,
do not use solvents or abrasive cleaning products.
Only use a cloth with warm soapy water.
To remove spots or stains from the surface of the
interior, use a cloth dampened with water with a little
vinegar, or a cleaning product made specifically for
dishwashers.
If the appliance must be moved, try to keep it in the
vertical position. If absolutely necessary, it can be
positioned on its back.
Seals
One of the factors that cause odors to form in the
dishwasher is food that remains trapped in the seals.
Periodic cleaning with a damp sponge will prevent this
from occurring.
Electrical Shock Hazard
Disconnect electrical power
before installing dishwasher.
The installation of the pipes
and electrical equipments
should be done by qualified
professionals.
Failure to do so can result in
death or electrical shock.
The installation position of dishwasher should be near the existing water inlet tap and drain
outlet and power socket.
One side of the cabinet sink should be chosen to facilitate the connection of drain
hoses of the dishwasher.
15
Position the appliance on a table or similar support. The back should rest against the wall behind it,
and the sides, along the adjacent cabinets or wall. The dishwasher is equipped with water supply
and drain hoses that can be positioned to the right or the left to facilitate proper installation.
For personal safety:
Do not use an extension cord or an adapter plug
with this appliance.
Do not cut or remove the earthing under any
circumstances .
Connection from the power cord.
Please look at the rating label to know the rating voltage and connect the dishwasher to the appropriate power supply.
Use the required fuse 10 amp, time delay fuse or circuit breaker recommended and provide separate circuit serving
only this appliance.
Ensure the voltage and frequency of the power being corresponds to
those on the rating plate. Only insert the plug into an electrical socket which is earthed
properly. If the electrical socket to which the appliance must be connected is not
appropriate for the plug , replace the socket, rather than using a adaptors or the like as
they could cause overheating and burns.
Connect the cold water supply hose to a threaded 3/4(inch) connector and make sure
that it is fastened tightly in place. If the water pipes are new or have not been used for
an extended period of time, let the water run to make sure that the water is clear and
free of impurities. If this precaution is not taken, there is a risk that the water inlet can
get blocked and damage the appliance.
Please Note: If the supplied hose cloes not fit your tap, please contact your local
plumbing supply center where adapters are available for purchase.
please close the hydrant after using.
16
Insert the drain hose into a drain pipe with a minimum diameter of 4cm, or let it
run into the sink, making sure to avoid bending or crimping it. The free end of the
hose must be at a height lower than 60cm and must not be immersed into water to
avoid the backflow of it.
Counter
NOTE
The top of the hose
must be less than
600mm.
Front
Drain pipe
A
B
φ 40mm
17
How to Drain Excess Water From Hoses
If the sink is more than1000 mm higher than the floor, the excess water in hoses cannot be drained directly
into the sink. It will be necessary to drain excess water from hoses into a bowl or suitable
container that is held outside and lower than the sink.
Water Outlet
Connect the water drain hose. The drain hose must be correctly fitted to avoid water leaks.
Ensure that the water drain hose is not kinked or squashed.
Extension Hose
If you need a drain hose extension, make sure to use a similar drain hose.
It must be no longer than 4 metres,otherwise the cleaning effect of the dishwasher could be reduced.
The following things should be checked before starting the dishwasher.
1 The dishwasher is level and fixed properly.
2
3
4
5
6
7
The inlet valve is open.
Inlet hose connections are fully tightened and not leaking.
The wires are tightly connected.
The power is switched on.
The inlet and drain hoses are not kinked.
All packing and print materials should be taken out of the dishwasher.
After installation, please make sure to keep this manual.
The content of this manual is very helpful to the users.
18
Technical
problems
Fuse blown, or the
circuit breaker tripped.
Replace fuse or reset circuit breaker. Remove any other
appliances sharing the same circuit with the dishwasher
Power supply is not
turned on.
Make sure the dishwasher is turned on and the door is
closed securely.
Make sure the power cord is properly plugged into the
wall socket.
Door of dishwasher
not properly closed.
Make sure to close the door property and latch it.
Kink in drain hose
Check drain hose.
Filter clogged.
Check the coarse filter.
(see section titled " Cleaning The Filter ")
Kitchen sink clogged.
Check kitchen sink to make sure it is draining well.
If the problem is the kitchen sink not draining ,you may need
a plumber rather than a serviceman for dishwasher.
Improper detergent
Use only the special dishwasher detergent to avoid
suds. If this occurred, open the dishwasher and let suds
evaporate. Add 1 gallon of cold water to the tub. Close
and latch the dishwasher, then Start any wash cycle
to drain out the water. Repeat if necessary.
Spilled rinse-aid
Always wipe up rinse-aid spills immediately.
Detergent with
colourant was used.
Make sure that the detergent is the one without
colourant.
Hard water minerals
To clean the interior, use a damp sponge with
dishwasher detergent and wear rubber gloves.
Never use any other cleaner than dishwasher
detergent for the risk of foaming or suds.
General
problems
The affected items are
not corrosion resistant.
Noise
A programme was not
run after dishwasher
salt was added.
Traces of salt have
got into the wash cycle.
Always run the Quick wash programme .
without any crockery in the dishwasher and
without selecting the Turbo function (if present),
after adding dishwasher salt.
The lid of softer
is loose.
Check the lip .Ensure the fix is fine.
The spray arm is
knocking against
an item in a basket.
Interrupt the program, and rearrange the items
which are obstructing the spray arm.
Item of crockery
are loose
in the wash cabinet.
Interrupt the program,
and rearrange the items of crockery.
This may be caused
by on-site installation
or the cross-section of
the piping.
This has no influence on dishwasher function.
if in doubt, contact a suitably qualified plumber.
19
Unsatis
-factory
washing
result
Unsatis
-factory
drying
result
The dishes were not
loaded correctly.
See notes in " Loading the Dishwasher Baskets ".
The programme was
not powerful enough.
Select a more intensive programme.
See" Wash Cycle Table ".
Not enough detergent
was dispensed.
Use more detergent, or change your detergent.
Item are blocking
the path of spray arms.
Rearrange the items so that the spray can rotate freely.
The filter combination
in the base of wash
cabinet is not clean or
is not correctly fitted.
This may cause
the spray arm jets
to get blocked.
Clean and/or fit the filter combination correctly.
Clean the spray arm jets. See "Cleaning the Spray
Arms".
Combination of soft
water and too much
detergent.
Use less detergent if you have soft water and select
a shortest cycle to wash the glassware and to get
them clean.
Aluminum utensils
have rubbed against
dishes.
Use a mild abrasive cleaner to eliminate those marks.
Dishes block
detergent cups.
Re-loading the dishes properly.
Improper loading
Load the dishwasher as suggested in the directions.
Too little rinse-aid
Increase the amount of rinse-aid/Refill the rinse-aid
dispenser.
Dishes are removed
too soon.
Do not empty your dishwasher immediately after
washing. Open the door slightly so that the steam can
escape. Begin unloading the dishwasher only once t
he dishes are barely warm to the touch. Empty the low
basket first. This prevents water form dropping off
dishes in the upper basket.
Wrong programme
selection
In short programmes the washing temperature is lower.
This also lowers cleaning performance. Choose a
programme with a long washing time.
Using cutlery with
a low-quality coating
Water drainage is more difficult with these items.
Cutlery or dishes of this type are not suitable for
washing in the dishwasher.
In case of malfunctions,the appliance will display error codes to warn you:
E1
Longer inlet time.
Faucet is not opened, or water intake is
restricted, or water pressure is too low.
E3
Not reach the setting temperature.
Malfunction of heat element
E4
Overflow.
Some element of the dishwasher leaks
E9
Keep touching a button more than 30 seconds.
Water or something on the button.
ED
Failure of communication between main PCB with display pcb
Open circuit or break wiring for the communication
If overflow occurs, turn off the main water supply before calling a service.
If there is water in the base pan because of an overfill or small leak,
the water should be removed before restarting the dishwasher.
20
Height :
Width :
Depth :
Voltage connected Load :
Water pressure:
Power supply:
Capacity:
21
438mm
550mm
500mm
see rating label
0.04-1.0MPa
see rating label
6 Place settings
Technical Data Sheet
Manufacturer
BEKO
Type / Description
DTC36610W
Standard place settings
6
Energy efficiency class
A+
Annual energy consumption
174 kWh
Energy consumption of the standard cleaning cycle
0.61 kWh
Power consumption of off-mode
0.45 W
Power consumption of left-on mode
0.49 W
Annual water consumption
1820 liter
Drying efficiency class
A
Standard cleaning cycle
ECO 50℃
Program duration of the standard cleaning cycle
180 min
Noise level
49 dB(A) re 1 pW
Mounting
Free standing
Could be built-in
Yes
Height
43.8 cm
Width
55 cm
Depth (with connectors)
50 cm
Power consumption
1170-1380 W
Rated voltage / frequency
220-240 V~ / 50 Hz
Water pressure (flow pressure)
0.4-10 bar = 0.04-1 MPa
NOTE:
A + + + (highest efficiency) to D (lowest efficiency)
Energy consumption “174” kWh per year, based on 280 standard cleaning cycles using cold water fill and
the consumption of the low power modes. Actual energy consumption will depend on how the appliance is used.
Water consumption “1820”litres per year, based on 280 standard cleaning cycles. Actual water consumption
will depend on how the appliance is used.
A (highest efficiency) to G (lowest efficiency)
This program is suitable for cleaning soiled normally soiled tableware and that it is the
most efficient programme in terms of its combined energy and water consumption for
that type of tableware.
The above values have been measured in accordance with standards under specified operating conditions.
Results may vary greatly according to quantity and pollution of the dishes, water hardness,
amount of detergent, etc.
The manual is based on the European Union's standards and rules.
22
Download PDF
Similar pages