Intel® Server System SR1530SH/
SR1530HSH User’s Guide
A Guide for Technically Qualified Assemblers of Intel® Identified Subassemblies/
Products
Intel Order Number E12554-007
Disclaimer
Information in this document is provided in connection with Intel® products. No license, express or implied, by
estoppel or otherwise, to any intellectual property rights is granted by this document. Except as provided in Intel's
Terms and Conditions of Sale for such products, Intel assumes no liability whatsoever, and Intel disclaims any
express or implied warranty, relating to sale and/or use of Intel products including liability or warranties relating to
fitness for a particular purpose, merchantability, or infringement of any patent, copyright or other intellectual property
right. Intel products are not designed, intended or authorized for use in any medical, life saving, or life sustaining
applications or for any other application in which the failure of the Intel product could create a situation where
personal injury or death may occur. Intel may make changes to specifications and product descriptions at any time,
without notice.
Intel server boards contain a number of high-density VLSI and power delivery components that need adequate
airflow for cooling. Intel's own chassis are designed and tested to meet the intended thermal requirements of these
components when the fully integrated system is used together. It is the responsibility of the system integrator that
chooses not to use Intel developed server building blocks to consult vendor datasheets and operating parameters to
determine the amount of airflow required for their specific application and environmental conditions. Intel Corporation
can not be held responsible if components fail or the server board does not operate correctly when used outside any
of their published operating or non-operating limits.
Intel and Intel Xeon are trademarks or registered trademarks of Intel Corporation or its subsidiaries in the United
States and other countries.
* Other names and brands may be claimed as the property of others.
Copyright © 2007-2010, Intel Corporation. All Rights Reserved
ii
Intel® Server System SR1530SH/SR1530HSH User’s Guide
Safety Information
Important Safety Instructions
Read all caution and safety statements in this document before performing any of the
instructions. See also Intel Server Boards and Server Chassis Safety Information on the
Intel® Server Deployment Toolkit CD and/or at http://support.intel.com/support/
motherboards/server/sb/cs-010770.htm.
Wichtige Sicherheitshinweise
Lesen Sie zunächst sämtliche Warnund Sicherheitshinweise in diesem Dokument, bevor
Sie eine der Anweisungen ausführen. Beachten Sie hierzu auch die Sicherheitshinweise zu
Intel-Serverplatinen und Servergehäusen auf der Intel® Server Deployment Toolkit CD
oder unter http://support.intel.com/support/motherboards/server/sb/cs-010770.htm.
Consignes de sécurité
Lisez attention toutes les consignes de sécurité et les mises en garde indiquées dans ce
document avant de suivre toute instruction. Consultez Intel Server Boards and Server
Chassis Safety Information sur le Intel® Server Deployment Toolkit CD ou bien rendezvous sur le site http://support.intel.com/support/motherboards/server/sb/cs-010770.htm.
Instrucciones de seguridad importantes
Lea todas las declaraciones de seguridad y precaución de este documento antes de realizar
cualquiera de las instrucciones. Vea Intel Server Boards and Server Chassis Safety
Information en el Intel® Server Deployment Toolkit CD y/o en http://support.intel.com/
support/motherboards/server/sb/cs-010770.htm.
Intel® Server System SR1530SH/SR1530HSH User’s Guide
iii
重要安全指导
在执行任何指令之前,请阅读本文档中的所有注意事项及安全声明。 和/或
http://support.intel.com/support/motherboards/server/sb/CS-010770.htm 上的 Intel
Server Boards and Server Chassis Safety Information(《Intel
服务器主板与服务器机箱安全信息》)。
iv
Intel® Server System SR1530SH/SR1530HSH User’s Guide
Warnings
Heed safety instructions: Before working with your server product, whether you are
using this guide or any other resource as a reference, pay close attention to the safety
instructions. You must adhere to the assembly instructions in this guide to ensure and
maintain compliance with existing product certifications and approvals. Use only the
described, regulated components specified in this guide. Use of other products/
components will void the UL listing and other regulatory approvals of the product and
will most likely result in noncompliance with product regulations in the region(s) in which
the product is sold.
System power on/off: The power button DOES NOT turn off the system AC power. To
remove power from system, you must unplug the AC power cord from the wall outlet.
Make sure the AC power cord is unplugged before you open the chassis, add, or remove
any components.
Hazardous conditions, devices and cables: Hazardous electrical conditions may be
present on power, telephone, and communication cables. Turn off the server and
disconnect the power cord, telecommunications systems, networks, and modems attached
to the server before opening it. Otherwise, personal injury or equipment damage can
result.
Electrostatic discharge (ESD) and ESD protection: ESD can damage disk drives,
boards, and other parts. We recommend that you perform all procedures in this chapter
only at an ESD workstation. If one is not available, provide some ESD protection by
wearing an antistatic wrist strap attached to chassis ground any unpainted metal surface on
your server when handling parts.
ESD and handling boards: Always handle boards carefully. They can be extremely
sensitive to ESD. Hold boards only by their edges. After removing a board from its
protective wrapper or from the server, place the board component side up on a grounded,
static free surface. Use a conductive foam pad if available but not the board wrapper. Do
not slide board over any surface.
Installing or removing jumpers: A jumper is a small plastic encased conductor that slips
over two jumper pins. Some jumpers have a small tab on top that you can grip with your
fingertips or with a pair of fine needle nosed pliers. If your jumpers do not have such a tab,
take care when using needle nosed pliers to remove or install a jumper; grip the narrow
sides of the jumper with the pliers, never the wide sides. Gripping the wide sides can
damage the contacts inside the jumper, causing intermittent problems with the function
controlled by that jumper. Take care to grip with, but not squeeze, the pliers or other tool
you use to remove a jumper, or you may bend or break the pins on the board.
Intel® Server System SR1530SH/SR1530HSH User’s Guide
v
vi
Intel® Server System SR1530SH/SR1530HSH User’s Guide
Preface
About this Manual
Thank you for purchasing and using the Intel® Server System SR1530SH/SR1530HSH.
This manual is written for system technicians responsible for troubleshooting, upgrading,
and repairing this server system. This document provides reference information, feature
information, and step-by-step instructions on how to add and replace components on the
server system. For the latest version of this manual, see http://support.intel.com/support/
motherboards/server/S3200SH/.
Manual Organization
Chapter 1 provides an overview of the server system. In this chapter, you will find a list of
the server system features, illustrations of the product, and product diagrams to help you
identify components and their locations.
Chapter 2 provides instructions on using the utilities shipped with the board or that may be
required to update the system. This includes how to navigate through the BIOS Setup
screens, perform a BIOS update, and reset the password or CMOS. Information about the
specific BIOS settings and screens is available in the Intel® Server Board S3200SH/
S3210SH Technical Product Specification. See Table 1 for a link to the Technical Product
Specification.
Chapter 3 provides instructions on adding and replacing components. Use this chapter for
step-by-step instructions and diagrams for installing or replacing components such as the
fans, power supply, drives, and other components.
At the back of this manual, you will find technical specifications, troubleshooting tips,
regulatory information, complete safety information, “getting help” information, and the
warranty.
Intel® Server System SR1530SH/SR1530HSH User’s Guide
vii
Product Contents
The Intel® Server System SR1530SH/SR1530HSH ships with the Intel® Server Board
S3200SHL.
There are two versions of this server system: the Intel® Server System SR1530SH and the
Intel® Server System SR1530HSH. The contents of each server system are listed below.
Intel® Server System SR1530SH Contents
Your Intel® Server System SR1530SH ships with the following items:
• One Intel® Server Board S3200SHL installed in the server system
• One 350-W power supply module, installed in the server system
• Three cooling fans, with attached cables, installed in the server system:
— One PCI cooling fan
— Two system blower fans
• One passive heat sink, mounted behind the hard drives, next to the blower fans in the
server system
•
•
•
•
One hard disk drive 0 bracket, in the server system product box
One hard disk drive 1 bracket, installed in the server system
One slimline optical drive installation kit, in the server system product box
Screws:
— 6-32# flat-head screws for attaching the slimline optical drive and hard disk
drives to the chassis, and for attaching hard disk drives to the hard disk drive
brackets
— One 6-32# pan-head screw for the hard disk drive attached to the chassis
— Four M1.5 screws for attaching the brackets to the slimline optical drive
•
•
•
•
Rack handles, in the server system product box
Standard front panel, installed in the server system
One rail kit, in a separate box
Cables:
— Two SATA cables, installed in the server system
— One front panel USB cable, installed in the server system
— One front panel cable, installed in the server system
• Documentation, drivers, and installation CD
viii
Intel® Server System SR1530SH/SR1530HSH User’s Guide
Intel® Server System SR1530HSH Contents
Your Intel® Server System SR1530HSH ships with the following items:
•
•
•
•
•
•
•
One Intel® Server Board S3200SHL, installed in the server system
One 350-W power supply module, installed in the server system
Two system blower cooling fans, installed in the server system
One passive heat sink, attached to the hard disk drive 0 location in the server system
Three hard disk drive carriers, installed in the server system
One slimline optical drive installation kit, in the server system product box
Screws:
— 6-32# flat-head screws for attaching the slimline optical drive and hard disk
drives to the chassis, and for attaching hard disk drives to the hard disk drive
brackets
— One 6-32# pan-head screw for the hard disk drive attached to the chassis
— Four M1.5 screws for attaching the brackets to the slimline optical drive
•
•
•
•
Rack handles, in the server system product box
Standard front panel, installed in the server system
One rail kit, in a separate box
Cables:
— Three SATA cables, installed in the server system
— One front panel USB cable, installed in the server system
— One front panel cable, installed in the server system
• Documentation, drivers, and installation CD
Intel® Server System SR1530SH/SR1530HSH User’s Guide
ix
Server System References
If you need more information about this product or information about the accessories that
you can use with this server chassis, use the following resources.
Table 1. Server System References
For this Information or
Software
Use this Document or Software
Technical information
about the server chassis,
including sub-system
overviews and
mechanical drawings
Intel® Server System SR1530SH/SR1530HSH Technical Product
Specification
Technical information
about the server board,
including board layout,
connector pin-outs, timing
information, mechanical
drawings, and LED
information
Intel® Server Board S3200SH/S3210SH Technical Product
Specification
If you just received this
product and need to
install it
Intel® Server System SR1530SH/SR1530HSH Quick Start User's
Guide
Accessories or other Intel
server products
Spares/Parts List and Configuration Guide
http://support.intel.com/support/motherboards/server/s3200sh/
http://support.intel.com/support/motherboards/server/s3200sh/
You can find this in the product box.
This is available from your Intel field representative or on the Server
Configurator Tool at:
http://serverconfigurator.intel.com/default.aspx
x
Hardware (peripheral
boards, adapter cards)
and operating systems
that have been tested
with this product
Tested Hardware Operating Systems List (THOL)
To make sure your
system falls within the
allowed power budget
Power Budget Tool
For software to manage
your Intel® server
Intel® System Management
For diagnostics test
software
Diagnostics
http://support.intel.com/support/motherboards/server/s3200sh/
http://support.intel.com/support/motherboards/server/s3200sh/
http://support.intel.com/support/motherboards/server/s3200sh/
http://support.intel.com/support/motherboards/server/s3200sh/
Intel® Server System SR1530SH/SR1530HSH User’s Guide
Table of Contents
Safety Information ..................................................................................................... iii
Important Safety Instructions ................................................................................................ iii
Wichtige Sicherheitshinweise ............................................................................................... iii
Consignes de sécurité .......................................................................................................... iii
Instrucciones de seguridad importantes ............................................................................... iii
Warnings ................................................................................................................................ v
Preface ....................................................................................................................... vii
About this Manual ................................................................................................................ vii
Manual Organization ............................................................................................................ vii
Product Contents .................................................................................................................viii
Intel® Server System SR1530SH Contents .................................................................viii
Intel® Server System SR1530HSH Contents ............................................................... ix
Server System References .................................................................................................... x
Chapter 1: Server System Features .......................................................................... 1
Chassis Component Identification ......................................................................................... 5
System Front Panel (SR1530SH) .................................................................................. 5
System Front Panel (SR1530HSH) ............................................................................... 6
System Rear .................................................................................................................. 7
Peripheral Devices (SR1530SH) ................................................................................... 7
Peripheral Devices (SR1530HSH) ................................................................................ 8
Hard Disk Drives ............................................................................................................ 8
Slimline Optical Drive Carrier ........................................................................................ 9
Internal Components (SR1530SH) ..............................................................................10
Internal Components (SR1530HSH) ...........................................................................11
Server Board Connectors/Components ...............................................................................12
Configuration Jumpers ......................................................................................................... 13
Hardware Requirements ......................................................................................................14
Processor ....................................................................................................................14
Memory ........................................................................................................................14
Chapter 2: Server Utilities ........................................................................................ 15
Using the BIOS Setup Utility ................................................................................................15
Starting Setup ..............................................................................................................15
If You Cannot Access Setup ........................................................................................15
Setup Menus ...............................................................................................................15
Upgrading the BIOS .............................................................................................................17
Preparing for the Upgrade ...........................................................................................17
Upgrading the BIOS ....................................................................................................18
Intel® Server System SR1530SH / SR1530HSH User’s Guide
xi
Clearing the CMOS ............................................................................................................. 19
Chapter 3: Hardware Installations and Upgrades ..................................................21
Before You Begin ................................................................................................................ 21
Tools and Supplies Needed ........................................................................................ 21
System References ..................................................................................................... 21
Removing and Installing the Front Bezel ............................................................................. 22
Removing the Front Bezel ........................................................................................... 22
Installing the Front Bezel ............................................................................................. 23
Removing and Installing the Server Cover .......................................................................... 24
Removing the Server System Cover ........................................................................... 24
Installing the Server System Cover ............................................................................. 26
Removing and Installing the Processor Air Duct ................................................................. 27
Removing the Processor Air Duct ............................................................................... 27
Installing the Processor Air Duct ................................................................................. 29
Installing and Removing Memory ........................................................................................ 30
Installing DIMMs .......................................................................................................... 31
Removing DIMMs ........................................................................................................ 32
Replacing the Processor ..................................................................................................... 33
Removing the Heat Sink and Processor ..................................................................... 33
Installing the Processor ............................................................................................... 34
Installing the Heat Sink ............................................................................................... 36
Installing and Removing a Hard Drive (SR1530SH) ........................................................... 37
Installing a Hard Disk Drive (SR1530SH) ................................................................... 37
Removing a Hard Disk Drive (SR1530SH) ................................................................. 41
Installing and Removing a Hot-Swap SATA Drive (SR1530HSH) ...................................... 43
Installing a Hot-Swap SATA Drive (SR1530HSH) ...................................................... 43
Removing a Hot-Swap SATA Drive (SR1530HSH) .................................................... 45
Installing or Removing a Slimline Optical Drive (SR1530SH) ............................................. 46
Installing a Slimline Optical Drive ................................................................................ 46
Removing a Slimline Optical Drive .............................................................................. 49
Installing or Removing a Slimline Optical Drive (SR1530HSH) ........................................... 52
Installing a Slimline Optical Drive (SR1530HSH) ........................................................ 52
Removing a Slimline Optical Drive (SR1530HSH) ...................................................... 53
Installing and Removing the PCIe* Riser Assembly ............................................................ 55
Removing the PCIe* Riser Assembly .......................................................................... 55
Installing the PCIe* Riser Assembly ............................................................................ 56
Installing or Replacing a PCIe* Riser Card ......................................................................... 57
Removing a PCIe* Riser Card .................................................................................... 57
Installing a PCIe* Riser Card ...................................................................................... 58
Installing and Removing a PCI Add-in Card ........................................................................ 59
Installing a PCI Add-in Card ........................................................................................ 59
Removing a PCI Add-in Card ...................................................................................... 60
Replacing the Server Board ................................................................................................ 62
xii
Intel® Server System SR1530SH / SR1530HSH User’s Guide
Removing the Server Board ........................................................................................62
Installing the Server Board ..........................................................................................64
Replacing the CMOS Battery ...............................................................................................65
Replacing the Power Supply (SR1530SH) ..........................................................................67
Replacing the Power Supply (SR1530HSH) ........................................................................72
Replacing the Front Panel Board (SR1530SH) ...................................................................74
Replacing the Front Panel Board (SR1530HSH) .................................................................76
Replacing a System Fan (SR1530SH) ................................................................................79
Replacing the System Blower Fans (SR1530SH) .......................................................79
Replacing a System Fan (SR1530HSH) ..............................................................................83
Replacing the System Blower Fans (SR1530HSH) .....................................................83
Installing and Removing the Rack Handles .........................................................................85
Installing the Rack Handles .........................................................................................85
Removing the Rack Handles .......................................................................................86
Appendix A: Technical Reference .......................................................................... 87
Cable Routing ......................................................................................................................87
Power Cable Routing (SR1530SH) .............................................................................88
Data Cable Routing (SR1530SH) ................................................................................89
Cable Routing (SR1530HSH) ......................................................................................90
350-W Single Power Supply Input Voltages ........................................................................91
350-W Single Power Supply Output Voltages .....................................................................91
System Environmental Specifications ..................................................................................92
Appendix B: Troubleshooting ................................................................................. 93
Resetting the System ...........................................................................................................93
Problems following Initial System Installation ......................................................................94
First Steps Checklist ....................................................................................................94
Hardware Diagnostic Testing ...............................................................................................95
Verifying Proper Operation of Key System Lights .......................................................95
Confirming Loading of the Operating System ..............................................................95
Specific Problems and Corrective Actions ...........................................................................95
Power Light Does Not Light .........................................................................................96
No Characters Appear on Screen ...............................................................................96
Characters Are Distorted or Incorrect ..........................................................................97
System Cooling Fans Do Not Rotate Properly ............................................................97
Drive Activity Light Does Not Light ..............................................................................98
CD-ROM Drive or DVD-ROM Drive Activity Light Does Not Light ...............................98
Cannot Connect to a Server ........................................................................................98
Problems with Network ................................................................................................99
System Boots when Installing PCI Card ....................................................................100
Problems with Newly Installed Application Software .................................................100
Problems with Application Software that Ran Correctly Earlier .................................100
Devices are not Recognized under Device Manager (Microsoft Windows* Operating System) ................................................................................................................101
Intel® Server System SR1530SH / SR1530HSH User’s Guide
xiii
Hard Drive(s) are not Recognized ............................................................................. 101
Bootable CD-ROM Disk Is Not Detected .................................................................. 101
LED Information ........................................................................................................ 102
BIOS POST Beep Codes .......................................................................................... 102
Appendix C: Installation/Assembly Safety Instructions .....................................103
English ............................................................................................................................... 103
Deutsch ............................................................................................................................. 105
Français ............................................................................................................................. 107
Español ............................................................................................................................. 109
Italiano ............................................................................................................................... 112
Appendix D: Safety Information ............................................................................115
English ............................................................................................................................... 115
Server Safety Information ......................................................................................... 115
Safety Warnings and Cautions .................................................................................. 115
Intended Application Uses ........................................................................................ 116
Site Selection ............................................................................................................ 116
Equipment Handling Practices .................................................................................. 116
Power and Electrical Warnings ................................................................................. 117
System Access Warnings ......................................................................................... 118
Rack Mount Warnings ............................................................................................... 118
Electrostatic Discharge (ESD) ................................................................................... 119
Other Hazards ........................................................................................................... 119
Deutsch ............................................................................................................................. 120
Sicherheitshinweise für den Server ........................................................................... 120
Sicherheitshinweise und Vorsichtsmaßnahmen ....................................................... 120
Zielbenutzer der Anwendung .................................................................................... 121
Standortauswahl ....................................................................................................... 121
Handhabung von Geräten ......................................................................................... 121
Warnungen zu Netzspannung und Elektrizität .......................................................... 122
Warnhinweise für den Systemzugang ....................................................................... 123
Warnhinweise für Racks ........................................................................................... 123
Elektrostatische Entladungen (ESD) ......................................................................... 124
Andere Gefahren ....................................................................................................... 124
Français ............................................................................................................................. 125
Consignes de securite sur le serveur ........................................................................ 125
Séurité: avertissements et mises en garde ............................................................... 125
Domaines d’utilisation prévus ................................................................................... 126
Sélection d’un emplacement ..................................................................................... 126
Pratiques de manipulation de l’équipement .............................................................. 127
Alimentation et avertissements en matiére d’électricité ............................................ 127
Avertissements sur le cordon d’alimentation ............................................................. 128
Avertissements sur l’accés au systéme .................................................................... 128
Avertissements sur le montage en rack .................................................................... 129
xiv
Intel® Server System SR1530SH / SR1530HSH User’s Guide
Décharges électrostatiques (ESD) ............................................................................130
Autres risques ............................................................................................................130
Périphériques laser ....................................................................................................131
Español ..............................................................................................................................131
Información de seguridad del servidor ......................................................................131
Advertencias y precauciones sobre seguridad ..........................................................131
Aplicaciones y usos previstos ....................................................................................132
Seleccién de la ubicación ..........................................................................................132
Manipulacién del equipo ............................................................................................133
Advertencias de alimentacién y eléctricas .................................................................133
Advertencias sobre el cable de alimentación ............................................................133
Advertencias el acceso al sistema ............................................................................134
Advertencias sobre el montaje en bastidor ...............................................................136
Descarga electrostática (ESD) ..................................................................................136
Otros riesgos .............................................................................................................137
Appendix E: Regulatory and Compliance Information ....................................... 143
Product Regulatory Compliance ........................................................................................143
Product Safety Compliance .......................................................................................143
Product EMC Compliance - Class A Compliance ......................................................144
Certifications/Registrations/Declarations ...................................................................145
Product Regulatory Compliance Markings ................................................................145
Electromagnetic Compatibility Notices ..............................................................................147
FCC Verification Statement (USA) ............................................................................147
Industry Canada (ICES-003) .....................................................................................148
Europe (CE Declaration of Conformity) .....................................................................148
VCCI (Japan) .............................................................................................................148
BSMI (Taiwan) ...........................................................................................................148
Korean Compliance (RRL) ........................................................................................149
Regulated Specified Components .............................................................................149
Restriction of Hazardous Substances (RoHS) Compliance ...............................................150
End-of-Life/Product Recycling ...........................................................................................150
Appendix F: Warranty ............................................................................................ 151
Limited Warranty for Intel® Chassis Subassembly Products .............................................151
Appendix G: Getting Help ...................................................................................... 155
World Wide Web ................................................................................................................155
Telephone ..........................................................................................................................155
Intel® Server System SR1530SH / SR1530HSH User’s Guide
xv
xvi
Intel® Server System SR1530SH / SR1530HSH User’s Guide
List of Tables
Table 1. Server System References ......................................................................................... x
Table 2. Intel® Server System SR1530SH / SR1530HSH Feature Summary ........................... 3
Table 3. NIC LED Descriptions .................................................................................................7
Table 4. Setup Menu Key Use ................................................................................................16
Table 5. Power Supply Output Capability ................................................................................91
Table 6. System Environmental Specifications .......................................................................92
Table 7. Resetting the System ................................................................................................93
Table 8. LED Information ...................................................................................................... 102
Table 9. POST Error Beep Codes .........................................................................................102
Table 10. Product Regulatory Compliance Markings ............................................................145
Intel® Server System SR1530SH / SR1530HSH User’s Guide
xvii
xviii
Intel® Server System SR1530SH / SR1530HSH User’s Guide
List of Figures
Figure 1. Intel® Server System SR1530SH............................................................................... 1
Figure 2. Intel® Server System SR1530HSH ............................................................................ 2
Figure 3. Front Controls and LEDs (SR1530SH) ...................................................................... 5
Figure 4. Front Controls and LEDs (SR1530HSH).................................................................... 6
Figure 5. Back Panel Connectors.............................................................................................. 7
Figure 6. System Components (SR1530SH) .......................................................................... 10
Figure 7. System Components (SR1530HSH)........................................................................ 11
Figure 8. S3200SH Connector and Component Locations ..................................................... 12
Figure 9. Configuration Jumper Descriptions .......................................................................... 13
Figure 10. Clear CMOS Jumper.............................................................................................. 19
Figure 11. Removing the Front Bezel...................................................................................... 22
Figure 12. Installing the Front Bezel........................................................................................ 23
Figure 13. Removing the Server System Cover (SR1530SH) ................................................ 24
Figure 14. Removing the Server System Cover (SR1530HSH).............................................. 25
Figure 15. Installing the Server System Cover (SR1530SH) .................................................. 26
Figure 16. Installing the Server System Cover (SR1530HSH)................................................ 27
Figure 17. Removing the Processor Air Duct (SR1530SH)..................................................... 28
Figure 18. Removing the Processor Air Duct (SR1530HSH) .................................................. 28
Figure 19. Installing the Processor Air Duct (SR1530SH)....................................................... 29
Figure 20. Installing the Processor Air Duct (SR1530HSH) .................................................... 30
Figure 21. Installing the Memory ............................................................................................. 31
Figure 22. Lifting the Processor Socket Handle ...................................................................... 34
Figure 23. Opening the Load Plate ......................................................................................... 34
Figure 24. Removing the Shipping Cover ............................................................................... 35
Figure 25. Installing the Processor.......................................................................................... 35
Figure 26. Removing the Protective Socket Cover ................................................................. 35
Figure 27. Installing the Heat Sink .......................................................................................... 36
Figure 28. Locating Drive Positions (SR1530SH) ................................................................... 38
Figure 29. Removing Drive Carrier from the Server System (SR1530SH) ............................. 38
Figure 30. Installing Drive into Drive Carrier (SR1530SH) ...................................................... 39
Figure 31. Install Drive Assembly into the Server System (SR1530SH) ................................. 39
Figure 32. Connecting Hard Drive Power and Data Cables (SR1530SH) .............................. 40
Figure 33. Removing Drive Carrier from the Server System (SR1530SH) ............................. 41
Figure 34. Locating Drive Positions (SR1530HSH)................................................................. 43
Figure 35. Removing the Drive Carrier (SR1530HSH)............................................................ 44
Figure 36. Installing Drive into Drive Carrier (SR1530HSH) ................................................... 44
Figure 37. Install Drive Assembly into the Server System (SR1530HSH) .............................. 45
Figure 38. Lifting PCI Cooling Fan from Mounting Pegs (SR1530SH).................................... 47
Figure 39. Removing the Knock-out from the Sheet Metal Panel ........................................... 47
Figure 40. Attaching the Optical Drive to the Brackets............................................................ 48
Figure 41. Installing the Optical Drive into the System............................................................ 48
Figure 42. Installing the PCI Cooling Fan (SR1530SH) .......................................................... 49
Intel® Server System SR1530SH / SR1530HSH User’s Guide
xix
Figure 43. Lifting PCI Cooling Fan from Mounting Pegs (SR1530SH) ...................................
Figure 44. Removing the Optical Drive from the Server System ............................................
Figure 45. Removing the Optical Drive Brackets ....................................................................
Figure 46. Installing the PCI Cooling Fan (SR1530SH)..........................................................
Figure 47. Attaching the Optical Drive to the Attachment Bracket..........................................
Figure 48. Installing the Optical Drive into the System ...........................................................
Figure 49. Removing the Optical Drive from the System........................................................
Figure 50. Removing the Optical Drive from the Attachment Bracket ....................................
Figure 51. Removing PCIe* Riser Assembly from the Server System ...................................
Figure 52. Installing PCIe* Riser Assembly into the Server System.......................................
Figure 53. Removing Riser Card from Riser Assembly ..........................................................
Figure 54. Installing Riser Card onto Riser Assembly ............................................................
Figure 55. Installing an Add-In Card .......................................................................................
Figure 56. Removing a Full Height Add-In Card .....................................................................
Figure 57. Removing the Server Board ..................................................................................
Figure 58. Installing the Server Board ....................................................................................
Figure 59. Replacing the CMOS Battery.................................................................................
Figure 60. Disconnecting Power Cables (SR1530SH) ...........................................................
Figure 61. Removing Power Supply from the Server System (SR1530SH) ...........................
Figure 62. Installing Power Supply Module into the Server System (SR1530SH)..................
Figure 63. Connecting Power Cables (SR1530SH)................................................................
Figure 64. Removing Power Supply from the Server System (SR1530HSH).........................
Figure 65. Installing Power Supply Module into the Server System (SR1530HSH) ...............
Figure 66. Removing Front Panel Board from the Server System (SR1530SH) ....................
Figure 67. Installing Front Panel Board into the Server System (SR1530SH)........................
Figure 68. Removing Front Panel Board from the Server System (SR1530HSH)..................
Figure 69. Removing Light Pipes from the Front Panel Board (SR1530HSH) .......................
Figure 70. Installing Front Panel Board into the Server System (SR1530HSH) .....................
Figure 71. Installing Light Pipes on the Front Panel Board (SR1530HSH).............................
Figure 72. Disconnecting System Blower Fans (SR1530SH).................................................
Figure 73. Removing Bracket and System Blower Fans from Server System (SR1530SH) ..
Figure 74. Removing Fan from Fan Bracket (SR1530SH) .....................................................
Figure 75. Connecting System Blower Fans (SR1530SH) .....................................................
Figure 76. Removing Fan from the Server System (SR1530HSH).........................................
Figure 77. Installing Fan into the Server System (SR1530HSH) ............................................
Figure 78. Installing the Rack Handle .....................................................................................
Figure 79. Removing the Rack Handle ...................................................................................
Figure 80. Power Cable Routing (SR1530SH) .......................................................................
Figure 81. Data Cable Routing (SR1530SH) ..........................................................................
Figure 82. Cable Routing (SR1530HSH) ................................................................................
xx
50
50
51
51
53
53
54
54
55
56
57
58
60
61
63
64
66
68
69
70
71
72
73
74
75
76
77
77
78
79
80
81
82
84
84
85
86
88
89
90
Intel® Server System SR1530SH / SR1530HSH User’s Guide
1
Server System Features
This chapter briefly describes the main features of the server system. This chapter
provides illustrations of the product, a list of the server system features, and diagrams
showing the location of important components and connections on the server system.
Figure 1. Intel® Server System SR1530SH
Note: Figure 1 is shown with an optional optical drive installed.
Intel® Server System SR1530SH/SR1530HSH User’s Guide
1
Figure 2. Intel® Server System SR1530HSH
Note: Figure 2 is shown with an optional optical drive installed.
2
Intel® Server System SR1530SH/SR1530HSH User’s Guide
Table 2 summarizes the features of the server system.
Table 2. Intel® Server System SR1530SH / SR1530HSH Feature Summary
Feature
Description
Dimensions (S1530SH)
•
•
•
•
1.69 inches high (4.29 centimeters)
17 inches wide (43.18 centimeters)
20 inches deep (50.80 centimeters)
20 pounds (9 kilograms)
Dimensions
(SR1530HSH)
•
•
•
•
1.69 inches high (4.29 centimeters)
17 inches wide (43.18 centimeters)
25.5 inches deep (648 centimeters)
23 pounds (10.43 kilograms)
Server Board
Intel® Server Board S3200SHL
Processor
Processor and Front Side Bus (FSB) support
•
•
•
Supports Intel® Xeon® processor 3000 series and Intel®
Xeon® processor 3100 series, and Intel® Xeon® processor
3200 series and Intel® Xeon® processor 3300 series
Supports Intel® dual-core technology
Supports Intel® Extended Memory System 64 Technology
(Intel® EM64T)
Memory
Four DIMM sockets supporting stacked DDR2 667/800 MHz ECC
or non-ECC unbuffered memory (up to 8 GB of total system
memory)
Chipset
Intel® 3200 Chipset, consisting of:
•
•
Peripheral Interfaces
Intel® 3200/3210 Memory Controller Hub (MCH)
Intel® I/O Controller Hub (ICH9R)
External connections:
•
•
•
•
Stacked PS/2* ports for keyboard and mouse
DB9 Serial A port
Two RJ-45 NIC connectors for 10/100/1000 Mb connections
Two USB 2.0 ports
Internal connections:
•
•
•
•
One USB port header, which supports two USB 2.0 ports
One DH10 Serial B header
Six Serial ATA connectors
ATX-compliant 24-pin front panel header
I/O Control
SMSC* SCH5027 controller
Video
On-board iBMC Server Engine* with integrated video adapter and
external 8 MB video memory
LAN
•
•
Intel® 10/100/1000 82566E Gigabit Ethernet Controller
Intel® 10/100/1000 82541PI Gigabit Ethernet Controller
Intel® Server System SR1530SH/SR1530HSH User’s Guide
3
Table 2. Intel® Server System SR1530SH / SR1530HSH Feature Summary
Feature
Expansion Capabilities
(optional accessory
required)
Hard Drives
Support for one of the following:
•
One low-profile riser slot supporting a 1U PCI Express* riser
card
SATA support, 3 Gb/s: capable of supporting up to two drives
(SR1530SH) or three drives (SR1530HSH)
Peripherals
•
Slimline bay for SATA optical drive (optional)
front panel
•
•
•
•
•
•
•
One USB port
Power/sleep button
Status LED
Power LED
Hard drive activity LED
NIC1 activity LED
NIC2 activity LED
Power Supply
Fans
System Management
4
Description
One 350-watt power supply module
•
•
Three non-redundant fans (SR1530SH)
Two non-redundant fans (SR1530HSH)
Intel® System Management Software
Intel® Server System SR1530SH/SR1530HSH User’s Guide
Chassis Component Identification
This section helps you identify the components of your server system. If you are near the
system, you can also use the Quick Reference Label on the inside of the chassis cover to
assist in identifying components.
System Front Panel (SR1530SH)
The front of the server system includes the following buttons and LEDs.
A
B
C
D
E
F
G
AF001000
A.
USB Port
E.
Hard Disk Drive Activity LED
B.
Power Button
F.
NIC1 LED
C.
System Status LED
G.
NIC2 LED
D.
System Power LED
Figure 3. Front Controls and LEDs (SR1530SH)
Intel® Server System SR1530SH/SR1530HSH User’s Guide
5
System Front Panel (SR1530HSH)
The front of the server system includes the following buttons and LEDs.
E
B
A
C
D
G
F
AF001573
A.
NIC1 LED
E.
HDD Activity LED
B.
NIC2 LED
F.
USB Port
C.
Power LED
G.
Power Button
D.
System Status LED
H.
Figure 4. Front Controls and LEDs (SR1530HSH)
6
Intel® Server System SR1530SH/SR1530HSH User’s Guide
System Rear
A
B
C
D
I
H
G F
E
A.
AC Power Receptacle
F.
USB 0-1
B.
Mouse
G.
NIC 2 (10/100/1000 Mb)
C.
Serial Port A
H.
Video
D.
NIC 1 (10/100/1000 Mb)
I.
Keyboard
E.
PCI Add-in Card Bracket
AF002311
Figure 5. Back Panel Connectors
The NIC LEDs at the right and left of each NIC provide the following information.
Table 3. NIC LED Descriptions
LED
Left
Right
LED State
Description
Off
No network connection
Solid Amber
Network connection in place
Blinking Amber
Transmit/receive activity
Off
10 Mbps connection (if left LED is on or blinking)
Solid Amber
100 Mbps connection
Solid Green
1000 Mbps connection
Peripheral Devices (SR1530SH)
The server system provides locations and hardware for installing hard drives, slimline
CD-ROM drive, or DVD-ROM drive. You must purchase the drives separately. Available
options include:
• Slimline Optical Drive Bay
Intel® Server System SR1530SH/SR1530HSH User’s Guide
7
• Hard Disk Drive Bay HDD0 (located under the slimline optical drive bay)
• Hard Disk Drive Bay HDD1
Peripheral Devices (SR1530HSH)
The server system provides locations and hardware for installing hard drives, slimline
CD-ROM drive, or DVD-ROM drive. You must purchase the drives separately. Available
options include:
• Slimline Optical Drive Bay
• Hard Disk Drive Bay
Hard Disk Drives
The Intel® Server System SR1530SH/SR1530HSH provides six SATA ports. The six
SATA ports are near the front left side of the server board.
For instructions on installing hard drives, see “Installing and Removing a Hard Drive
(SR1530SH)” on page 37.
Note: Each drive can consume up to 17 W of power. Drives must be specified to run at a
maximum ambient temperature of 45 ° C.
Note: The Intel® Server System SR1530SH / SR1530HSH does not support all Serial ATA
(SATA) hard drives. See “Server System References” on page x for an Internet link to a
list of supported hardware.
8
Intel® Server System SR1530SH/SR1530HSH User’s Guide
Slimline Optical Drive Carrier
One slimline drive carrier is included with your server system; you must purchase the
optical drive separately. To use the slimline DVD drive provided by Intel, use order code
AXXSATADVDROM. To use the slimline DVD CDRW drive provided by Intel, use
order code AXXSATADVDRWROM.
Note: The Intel® Server System SR1530SH / SR1530HSH does not support all slimline optical
drives. See Table 1 on page x for an Internet link to a list of supported hardware. Intel
provides accessory kits for these drives.
For installation instructions for an optical drive, see “Installing or Removing a Slimline
Optical Drive (SR1530SH)” on page 46.
Intel® Server System SR1530SH/SR1530HSH User’s Guide
9
Internal Components (SR1530SH)
C
E
D
B
A
F
L
G
H
K
I
J
A
AF002314
A.
Rack Handles (two)
G.
Power Supply
B.
PCI Cooling Fan
H.
System Memory DIMM Sockets
C.
Server Board
I.
System Blower Fans (two)
D.
Processor Air Duct
J.
Hard Drive Bays
E.
PCIe* Riser Assembly
K.
Front Panel
F.
Processor and Heat Sink
L.
Slimline Optical Drive Bay
Figure 6. System Components (SR1530SH)
10
Intel® Server System SR1530SH/SR1530HSH User’s Guide
Internal Components (SR1530HSH)
C
D
F
E
B
A
G
H
M
L
K
I
J
A
AF002315
A.
Rack Handles (two)
H.
Power Supply
B.
PCI Air Baffle
I.
Front Panel Board
C.
System Blower Fans (two)
J.
Front Panel
D.
Processor Air Duct
K.
Hard Drive Carriers (two)
E.
Server Board
L.
Slimline Optical Drive Bay
F.
PCIe* Riser Assembly
M.
Hard Drive Carrier (one)
G.
Processor and Heat Sink
Figure 7. System Components (SR1530HSH)
Intel® Server System SR1530SH/SR1530HSH User’s Guide
11
Server Board Connectors/Components
A B
C
D E
F
G
H
I
GG
FF
J
EE
DD
CC
BB
AA
Z
Y
X
W VU
TS
R
Q P O
N M L
K
AF002310
A.
PCI (32bit/33MHz) Slot 1
B.
PCI (32bit/33MHz) Slot 2
C.
PCI Express* x8 (x4 lane)
D.
PCI Express* x16 (x1 lane)
E.
System Fan 1
F.
Back Panel Connectors
G.
Diagnostic LEDs
H.
Processor Fan 1 Connector
I.
2X4 Aux Power Connector
J.
Processor Socket
K.
Channel 2 DIMM Sockets
L.
Channel 1 DIMM Sockets
M.
System Fan 4 Connector
N.
System Fan 3 Connector
O.
Battery
P.
Main Power Connector
Q.
System Fan 2 Connector
R.
Floppy Connector
SATA 0
S.
HSBP
T.
U.
SATA1
V.
SATA 2
W. IPMB
X.
Front Panel Header
Y.
SATA 4
Z.
AA. SATA 3
SATA 5
BB. Internal USB
CC. External USB
DD. CMOS Clear Jumper
EE. Password Clear Jumper
FF. Recovery Mode Jumper
GG. Serial Port
Figure 8. S3200SH Connector and Component Locations
12
Intel® Server System SR1530SH/SR1530HSH User’s Guide
Configuration Jumpers
Diagnostic
LEDs
NIC 1
USB
USB
®
Intel 82566 E NIC Controller
BIT 1
LSB
NIC 2
3
Default
Update
NIC LED Functions
LED Color LED State NIC State
Off
LAN link is not established.
Left Green
External
USB
CPUFan 1
On
Blinking
CPU Power
CPU Socket
N/A
Right Green
Off
On
Yellow
On
LAN link is established.
LAN activity is occurring.
10 Mbit/sec data rate is selected.
100 Mbit/sec data rate is selected.
1000 Mbit/sec data rate is selected.
A
Internal
USB
SATA 3
DIMM B1
DIMM B2
J1E2
MS
KB
DIMM A1
DIMM A2
Password
Clear 2
Serial
VGA
Battery
3
Remove jumper for BIOS recovery
PCI Express* x16 (x16 Lane) Slot 6
J1E1
Default
Note: Refer to the Technical
Product Specification for
Diagnostic LED decoder list.
SysFan 1
PCI Express* x8
(x8 Lane) Slot 3
BIOS
Recovery 2
PCI 5V (32bit/33MHz) Slot 1
Serial
Port
PCI 5V (32bit/33MHz) Slot 2
Intel® 82541 NIC
BIT 2
MSB
SATA 5
CMOS
Clear 2
J1E3
3
Default
Main
Power
IPMB
HSBP
SATA 4
CLEAR
CMOS Front Panel
Header
SysFan 4
SATA 2
SATA 1
SATA 0
Floppy
SysFan 2
SysFan 3
A
Jumper Name
BIOS Recovery
Jumper Purpose
Jumper in normal position (pins 1-2) allows normal system
operation with correct BIOS settings. System will POST normally.
Jumper in maintenance mode (pins 2-3) allows Intel® AMT setting/
password reset.
Jumper removed is used to recover from a corrupted BIOS.
Bootable media with a valid BIOS ROM required.
Password Clear
Jumper in normal position (pins 1-2) allows the system to
successfully POST and boot to the operating system environment.
BIOS settings are kept intact.
Jumper in clear position (pins 2-3) initiates a clearing of password.
CMOS Clear
Jumper in normal position (pins 1-2) allows the system to
successfully POST and boot to the operating system environment.
BIOS settings are kept intact.
Jumper in clear position (pins 2-3) initiates a clearing of NVRAM
following POST. A system message confirms the CMOS clear
operation was successful. This setting enforces default BIOS
settings, which you can change by entering setup pressing F2, then
exiting setup pressing F10 and saving changes.
Figure 9. Configuration Jumper Descriptions
Intel® Server System SR1530SH/SR1530HSH User’s Guide
13
Hardware Requirements
To avoid integration difficulties and possible board damage, your system must meet the
following requirements outlined. For a list of qualified components, see the links under
“Server System References”.
Processor
Supports Intel® Xeon® processor 3000 series and Intel® Xeon® processor 3100 series,
and Intel® Xeon® processor 3200 series and Intel® Xeon® processor 3300 series.
For a complete list of supported processors, see the links under “Server System
References” on page x.
Memory
The Intel® Server System SR1530SH / SR1530HSH provides four DIMM sockets across
two banks, bank 1 and bank 2. Bank 1 consists of DIMM sockets A1 and B1. Bank 2
consists of DIMM sockets A2 and B2.
A minimum of one 512-MB DIMM is required in DIMM socket A1. This uses singlechannel interleave. However, for dual-channel interleave, providing optimum
performance, you should install a minimum of two DIMMs in DIMM sockets A1 and A2.
To operate in dual-channel dynamic paging mode, the following conditions must be met:
• Populate two identical DIMMs in sockets DIMMA1 and DIMMB1.
• Populate four identical DIMMs in each socket location.
Note: Installing only three DIMMs is not supported. Use DIMMs that are the same type and
speed. Use of identical DIMMs is preferred.
DIMMs must meet the following requirements:
• Use only DIMMs with DDR2 DRAM technology.
• Use only DDR2-667 and DDR2-800 stacked DIMM modules.
In determining your memory requirements, you must consider the need for memory
sparing or memory mirroring. For a complete list of supported memory DIMMs, see the
links under “Server System References” on page x.
14
Intel® Server System SR1530SH/SR1530HSH User’s Guide
2
Server Utilities
Using the BIOS Setup Utility
This section describes the BIOS Setup Utility options, which are used to change server
configuration defaults. You can run BIOS Setup with or without an operating system
present. See the links under “Server System References” on page x for a link to the Intel®
Server Board S3200SH Technical Product Specification where you will find details about
specific BIOS setup screens.
Starting Setup
You can enter and start BIOS Setup under several conditions:
• When you turn on the server, after POST completes the memory test.
• When you have moved the CMOS jumper on the server board to the “Clear CMOS”
position (enabled).
In the two conditions listed previously, during the Power On Self Test (POST), you will
see this prompt:
Press <F2> to enter SETUP
In a third condition, when CMOS/NVRAM is corrupted, you will see other prompts but
not the <F2> prompt:
Warning: CMOS checksum invalid
Warning: CMOS time and date not set
In this condition, the BIOS loads the default values for CMOS and attempts to boot.
If You Cannot Access Setup
If you cannot access the BIOS Setup, you might need to clear the CMOS memory. For
instructions on clearing the CMOS, see “Clearing the CMOS” on page 19.
Setup Menus
Each BIOS Setup menu page contains a number of features. Except for those features that
are provided only to display automatically configured information, each feature is
associated with a value field that contains user-selectable parameters. A user can change
these parameters if they have adequate security rights. If a value cannot be changed for
any reason, the feature's value field is inaccessible.
Intel® Server System SR1530SH/SR1530HSH User’s Guide
15
“Setup Menu Key Use” describes the keyboard commands you can use in the BIOS Setup
menus.
Table 4. Setup Menu Key Use
Key to Press
Description
<F1>
Pressing the <F1> key on any menu opens the general help window.
Left and right arrows
The left and right arrow keys are used to move between the major menu
pages. The keys have no effect if a submenu or pick list is displayed.
Up arrow
Select Item up - The up arrow is used to select the previous value in a
menu item's option list, or a value field pick list. Pressing <Enter>
activates the selected item.
Down arrow
Select Item down - The down arrow is used to select the next value in a
menu item's option list, or a value field pick list. Pressing <Enter>
activates the selected item.
<F5> or <->
Change Value - The minus key or the <F5> function key is used to
change the value of the current item to the previous value. This key
scrolls through the values in the associated pick list without displaying
the full list.
<F6> or <+>
Change Value - The plus key or the <F6> function key is used to change
the value of the current menu item to the next value. This key scrolls
through the values in the associated pick list without displaying the full
list. On 106-key Japanese keyboards, the plus key has a different scan
code than the plus key on the other keyboard, but it has the same effect.
<Enter>
Execute Command - The <Enter> key is used to activate submenus
when the selected feature is a submenu, or to display a pick list if a
selected feature has a value field, or to select a sub-field for multi-valued
features like time and date. If a pick list is displayed, pressing <Enter>
will undo the pick list, and allow another selection in the parent menu.
<Esc>
Exit - The <Esc> key provides a mechanism for backing out of any field.
This key will undo the pressing of the <Enter> key. When <Esc> is
pressed while editing any field or selecting features of a menu, the
parent menu is re-entered. When <Esc> is pressed in any submenu, the
parent menu is re-entered. When <Esc> is pressed in any major menu,
the exit confirmation window displays and the user is asked whether
they want to discard their changes.
<F9>
Setup Defaults - Pressing <F9> causes the following to display:
Setup Confirmation
Load default configuration now?
[Yes] [No]
If “Yes” is selected and <Enter> is pressed, all Setup fields are set to
their default values. If “No” is selected and <Enter> is pressed, or <Esc>
is pressed, the user is returned to where they were before <F9> was
pressed without affecting any existing field values.
16
Intel® Server System SR1530SH/SR1530HSH User’s Guide
Table 4. Setup Menu Key Use
Key to Press
<F10>
Description
Save and Exit - Pressing <F10> causes the following message to
display:
Setup Confirmation
Save Configuration changes and exit now?
[Yes] [No]
If “Yes” is selected and <Enter> is pressed, all changes are saved and
Setup is exited. If “No” is selected and <Enter> is pressed, or <Esc> is
pressed, the user is returned to where they were before <F10> was
pressed without affecting any existing values.
Upgrading the BIOS
The upgrade utility allows you to upgrade the BIOS in flash memory. The code and data in
the upgrade file include the following:
• On-board system BIOS, including the recovery code, BIOS Setup Utility, and
strings.
• On-board video BIOS, and other option ROMs for devices embedded on the server
board.
• OEM binary area
• Microcode
• A way to change the BIOS language
Preparing for the Upgrade
The following steps explain how to prepare to upgrade the BIOS, including how to record
the current BIOS settings and obtain the upgrade utility.
Note: In the unlikely event that a BIOS error occurs during the BIOS update process, you may
need to follow a recovery process to return the system to service. See “Server System
References” on page x for a link to necessary software and instructions.
Recording the Current BIOS Settings
1. Boot the computer and press <F2> when you see the following message:
Press <F2> Key if you want to run SETUP
2. Write down the current settings in the BIOS Setup program.
Note: Do not skip Step 2. You need these settings to configure your server at the end of the
procedure.
Intel® Server System SR1530SH/SR1530HSH User’s Guide
17
Obtaining the Upgrade
Download the BIOS image file to a temporary folder on your hard drive. See “Server
System References” on page x for a link to the update software.
Note: Before attempting a BIOS upgrade, review the instructions and release notes provided in
the readme file distributed with the BIOS image file. The release notes contain critical
information regarding jumper settings, specific fixes, and other information to complete
the upgrade.
Upgrading the BIOS
Follow the instructions in the readme file that came with the BIOS upgrade. When the
update completes, remove the bootable media from which you performed the upgrade.
Caution: Do not power down the system during the BIOS update process!
Note: You may encounter a CMOS Checksum error or other problem after reboot. If this
happens, shut down the system and boot it again. CMOS checksum errors require that you
enter Setup, check your settings, save your settings, and exit Setup.
18
Intel® Server System SR1530SH/SR1530HSH User’s Guide
Clearing the CMOS
If you cannot access the BIOS setup screens, you must use the CMOS Clear jumper to
reset the configuration RAM.
1. Power down the system and disconnect the AC power.
2. Open the server.
3. Move the jumper from the normal operation position, CMOS Clear by BMC, at
pins 1 and 2 to the CMOS Clear Force Erase position, covering pins 2 and 3.
NIC1 LED Functions
On
100 Mbit/sec data rate is selected.
NIC2 LED Functions
LED
Color
Left
N/A
Green
Yellow
Right
Green
LED State
Off
NIC State
10 Mbit/sec data rate is selected.
On
100 Mbit/sec data rate is selected.
On
1000 Mbit/sec data rate is selected.
LAN link is not established.
Off
On
Blinking
Default
Serial
Port B
2
LAN link is established.
BMC
Boot
Block WP 2
J1C2 3
LAN activity is occurring.
BIOS
Recovery 2
J1E1
3
Front Panel
Header (J1K2)
24 23
Default
Remove jumper for BIOS recovery
NIC 2
Link/Act
B
External
USB
Default
NIC 2
D
A
Update
Default
Chassis
Intrusion
J1B2
NIC 1
USB
USB
Intel® 82566 E NIC Controller (optional)
BMC
FRC
2
Update
J1B1 3
1000 Mbit/sec data rate is selected.
Note: Refer to the Technical
Product Specification for
Diagnostic LED decoder list.
Serial
VGA
MS
KB
SysFan 1
CPUFan 1
CPU Power
CPU Socket
C
Internal
USB
SATA 3
DIMM B1
DIMM B2
Off
On
Diagnostic LEDs
BIT 3
BIT 2
MSB
LSB
C Intel® Adaptive Slot 6 functions as either a PCI Express* x16
(x8 lane) Connector or a Riser Card Slot in a 1U Chassis.
D Not Available on the Intel® Server Board S3200SHV.
DIMM A1
DIMM A2
N/A
Green
Yellow
B Not Available on the Intel® Server Board S3200SHV.
LAN activity is occurring.
10 Mbit/sec data rate is selected.
Battery
Right
A Not Available on the Intel® Server Board S3200SHV.
LAN link is established.
PCI Express* x8
(x8 Lane) Slot 5
Blinking
NIC State
LAN link is not established.
PCI Express* x16 (x8 Lane) Slot 6
On
PCI Express* x8
(x4 Lane) Slot 3
LED State
Off
Green
PCI 5V (32bit/33MHz) Slot 2
Color
Left
PCI 5V (32bit/33MHz) Slot 1
LED
SATA 5
Reset
Button
Power
Button
HDD LED
NIC 1
Link/Act
Power LED
Password
Clear 2
J1E2
3
CMOS
Clear
J1E3
SATA 4
Update
IPMB
HSBP
SGPIO
Main
Power
Front Panel
Header
Default
2
3
2
Default
CLEAR
CMOS
SATA 2
SATA 1
SATA 0
Floppy
SysFan 2
SysFan 3
SysFan 4
Figure 10. Clear CMOS Jumper
4. Reconnect the AC power and power up the system.
5. When the system begins beeping, power it down and disconnect the AC power.
6. Return the CMOS Clear jumper to the CMOS Clear by BMC location, covering
pins 1 and 2.
7. Close the server chassis.
8. Reconnect the AC power and power up the system.
Intel® Server System SR1530SH/SR1530HSH User’s Guide
19
20
Intel® Server System SR1530SH/SR1530HSH User’s Guide
3
Hardware Installations and
Upgrades
Caution: No components in the Intel® Server System SR1530SH/SR1530HSH are hot-swappable.
Before removing or installing any component in this server system, you must first take the
server out of service, turn off all peripheral devices connected to the system, turn off the
system by pressing the power button, and unplug the AC power cord from the system or
wall outlet.
Note: Some components in the Intel® Server System SR1530HSH are hot-swappable and are
noted as such (where applicable) in the following instructions.
Note: Most of the illustrations in this chapter show the Intel® Server System SR1530SH with an
optional optical drive installed. Unless otherwise noted, the instructions for removing and
installing components are the same for the Intel® Server System SR1530HSH. When
instructions differ, separate illustrations are shown for the Intel® Server System
SR1530HSH.
Before You Begin
Before working with your server product, pay close attention to the “Safety Information”
on page iii.
Tools and Supplies Needed
• Phillips* (cross head) screwdriver, #1 bit and #2 bit
• Antistatic wrist strap and conductive foam pad (recommended)
System References
All references to the left, right, front, top, and bottom assume the reader is facing the front
of the server system as it would be positioned for normal operation.
Intel® Server System SR1530SH/SR1530HSH User’s Guide
21
Removing and Installing the Front Bezel
The front bezel is available as an optional accessory for the Intel® Server System
SR1530SH / SR1530HSH. Note the orientation in the following figures and make sure
you position your bezel as shown.
Removing the Front Bezel
If your system includes a front bezel, use the following steps.
1. Unlock the bezel.
2. Pull the bezel from the server system.
AF002316
Figure 11. Removing the Front Bezel
22
Intel® Server System SR1530SH/SR1530HSH User’s Guide
Installing the Front Bezel
The front bezel is optional.
1. At each end of the bezel, line up the center notch on the bezel with the center guide
on the rack handles.
2. Push the bezel onto the front of the server system until it clicks into place.
3. Lock the bezel.
AF002317
Figure 12. Installing the Front Bezel
Intel® Server System SR1530SH/SR1530HSH User’s Guide
23
Removing and Installing the Server Cover
Removing the Server System Cover
You must operate the server system with the server system cover in place to ensure proper
cooling. You must remove the cover to add or replace components inside of the server.
None of the internal components are hot-swappable. Before removing the server system
cover, power down the server and unplug all peripheral devices and the AC power cable.
Note: You may need a non-skid surface or a stop behind the server system to prevent the server
system from sliding on your work surface.
1. Observe the safety and ESD precautions at the beginning of this book. See “Safety
Information” on page iii.
2. Turn off all peripheral devices connected to the server. Turn off the server.
3. Disconnect the AC power cord.
4. SR1530SH: Remove the two screws at the front of the chassis. See letter “A” in
Figure 13.
5. SR1530SH: Loosen the screw at the rear of the chassis. See letter “B” in Figure 13.
6. SR1530SH: Push rearward on the blue grip point at the front of the server. Slide the
cover back until it stops and then lift the cover upward to remove it. See letter “C”
in Figure 13.
B
C
A
AF000662
Figure 13. Removing the Server System Cover (SR1530SH)
24
Intel® Server System SR1530SH/SR1530HSH User’s Guide
7. SR1530HSH: Remove the four screws at the front of the chassis. See letter “A” in
Figure 14.
8. SR1530HSH: Push rearward on the blue grip point at the front of the server. Slide
the cover back until it stops and then lift the cover upward to remove it. See letter
“B” in Figure 14.
B
A
AF001578
Figure 14. Removing the Server System Cover (SR1530HSH)
Intel® Server System SR1530SH/SR1530HSH User’s Guide
25
Installing the Server System Cover
1. Observe the safety and ESD precautions at the beginning of this book. See “Safety
Information” on page iii.
2. SR1530SH: Place the cover over the server system so that the side edges of the
cover sit just inside the server system sidewalls. Slide the cover forward. See letter
“A” in Figure 15.
3. SR1530SH: Tighten the screw at the rear of the server. See letter “B” in Figure 15.
4. SR1530SH: Install the two screws at the front of the server. See letter “C” in
Figure 15.
B
A
C
AF000663
Figure 15. Installing the Server System Cover (SR1530SH)
5. SR1530HSH: Place the cover over the server system so the side edges of the cover
sit just inside the server system sidewalls. Slide the cover forward. See letter “A” in
Figure 16.
6. SR1530HSH: Install the four screws at the front of the server. See letter “B” in
Figure 16.
26
Intel® Server System SR1530SH/SR1530HSH User’s Guide
A
B
AF001579
Figure 16. Installing the Server System Cover (SR1530HSH)
7. Reconnect all peripheral devices and the AC power cord.
Removing and Installing the Processor Air Duct
Always operate your server system with the processor air duct in place. The air duct is
required for proper airflow within the server system.
Removing the Processor Air Duct
1. Observe the safety and ESD precautions at the beginning of this book. See “Safety
Information” on page iii.
2. Power down the server and unplug all peripheral devices and the AC power cable.
3. Remove the server system cover. For instructions, see “Removing the Server
System Cover”.
4. Lift the processor air duct from its location behind the two system blower fans (see
Figure 17 for SR1530SH; see Figure 18 for SR1530HSH).
Intel® Server System SR1530SH/SR1530HSH User’s Guide
27
AF002318
Figure 17. Removing the Processor Air Duct (SR1530SH)
AF002319
Figure 18. Removing the Processor Air Duct (SR1530HSH)
28
Intel® Server System SR1530SH/SR1530HSH User’s Guide
Installing the Processor Air Duct
1. Observe the safety and ESD precautions at the beginning of this book. See “Safety
Information” on page iii.
2. Power down the server and unplug all peripheral devices and the AC power cable.
3. Remove the server system cover. For instructions, see “Removing the Server
System Cover” on page 24.
4. Lower the air duct into place, insert the two hooks at the front of the processor air
duct into the corresponding slots on the bracket behind the two system blower fans
(see Figure 19for SR1530SH); see Figure 20 for SR1530HSH). Use caution not to
pinch or disengage cables that may be near or under the air duct.
5. Install the server system cover. For instructions, see “Installing the Server System
Cover”.
AF002320
Figure 19. Installing the Processor Air Duct (SR1530SH)
Intel® Server System SR1530SH/SR1530HSH User’s Guide
29
AF002321
Figure 20. Installing the Processor Air Duct (SR1530HSH)
Installing and Removing Memory
Caution: The memory is NOT hot-swappable. Before removing or replacing any memory DIMM,
you must first take the server out of service, turn off all peripheral devices connected to
the system, turn off the system by pressing the power button, and unplug the AC power
cord from the system or wall outlet.
The silkscreen on the board for the DIMMs displays DIMM A1, DIMM A2, DIMM B1,
and DIMM B2 starting from the center of the board. See “Memory” on page 14 for a
discussion of the memory requirements and options. See “Server System References” on
page x for a link to the list of tested DIMMs.
30
Intel® Server System SR1530SH/SR1530HSH User’s Guide
Installing DIMMs
To install DIMMs, follow these steps:
1. Observe the safety and ESD precautions at the beginning of this book. See “Safety
Information” on page iii.
2. Power down the server and unplug all peripheral devices and the AC power cable.
3. Remove the server system cover. For instructions, see “Removing the Server
System Cover” on page 24.
4. Locate the DIMM sockets. See Figure 21.
C
D
B
A
DIMM 1A
Socket
DIMM 2B
Socket
DIMM 2A
Socket
DIMM 1B
Socket
AF002309
Figure 21. Installing the Memory
5. Make sure the clips at both ends of the DIMM socket(s) are pushed outward to the
open position. See letter “A” in Figure 21.
6. Holding the DIMM by the edges, remove it from its anti-static package.
7. Position the DIMM above the socket. Align the notch on the bottom edge of the
DIMM with the key in the DIMM socket. See letter “B” in Figure 21.
8. Insert the bottom edge of the DIMM into the socket. See letter “C” in Figure 21.
Intel® Server System SR1530SH/SR1530HSH User’s Guide
31
9. When the DIMM is correctly positioned, push down on the top edge of the DIMM
until the retaining clips snap into place.
10. Make sure the clips are firmly in place. See letter “D” in Figure 21.
11. Install the server system cover. For instructions, see “Installing the Server System
Cover”.
Removing DIMMs
To remove a DIMM, follow these steps:
1. Observe the safety and ESD precautions at the beginning of this book. See “Safety
Information” on page iii.
2. Power down the server and unplug all peripheral devices and the AC power cable.
3. Remove the server system cover. For instructions, see “Removing the Server
System Cover” on page 24.
4. Locate the DIMM sockets. See Figure 21.
5. Gently spread the retaining clips at each end of the socket. The DIMM lifts from
the socket.
6. Holding the DIMM by the edges, lift it from the socket, and store it in an anti-static
package.
7. Install the server system cover. For instructions, see “Installing the Server System
Cover”.
32
Intel® Server System SR1530SH/SR1530HSH User’s Guide
Replacing the Processor
Note: This manual assumes a processor is already installed and you are referring to these steps
to replace your processor. If you are setting up this system for the first time, see the Quick
Start User’s Guide included in the product box.
Caution: Use only processors validated to work with this server board. See “Server System
References” on page x for a link to the list of compatible processor(s).
Caution: ESD and handling processors: Reduce the risk of electrostatic discharge (ESD) damage to
the processor by doing the following: (1) Touch the metal chassis before touching the
processor or server board. Keep part of your body in contact with the metal chassis to
dissipate the static charge while handling the processor. (2) Avoid moving around
unnecessarily.
Removing the Heat Sink and Processor
1. Observe the safety and ESD precautions at the beginning of this book. See “Safety
Information” on page iii.
2. Power down the server and unplug all peripheral devices and the AC power cable.
3. Remove the server system cover. For instructions, see “Removing the Server
System Cover” on page 24.
4. Loosen the four captive screws on the corners of the heat sink.
5. Twist the heat sink slightly to break the seal between the heat sink and the
processor.
6. Lift the heat sink from the processor. If it does not pull up easily, twist the heat sink
again. Do not force the heat sink from the processor. Doing so could damage the
processor.
7. Lift the processor lever.
8. Raise the CPU load plate.
9. Remove the processor.
10. If installing a replacement processor, see “Installing the Processor” on page 34.
Otherwise, install the protective socket cover over the empty processor socket and
then reinstall the chassis cover.
Intel® Server System SR1530SH/SR1530HSH User’s Guide
33
Installing the Processor
To install a processor, follow these instructions:
1. Observe the safety and ESD precautions at the beginning of this book. See “Safety
Information” on page iii.
2. Power down the server and unplug all peripheral devices and the AC power cable.
3. Remove the server system cover. For instructions, see “Removing the Server
System Cover” on page 24.
4. Locate the processor socket and raise the socket handle completely. See Figure 22.
AF000528
Figure 22. Lifting the Processor Socket Handle
5. Push the rear tab with your finger to slightly lift the front of the load plate. Raise the
load plate completely. Raise the CPU load plate (see Figure 23).
A
B
AF000529
Figure 23. Opening the Load Plate
Caution: Do not touch the socket pins; they are very sensitive and easily damaged.
34
Intel® Server System SR1530SH/SR1530HSH User’s Guide
6. Remove the processor from the packaging box and remove the protective shipping
cover. See Figure 24.
A
AF000531
Figure 24. Removing the Shipping Cover
7. Orient the processor with the socket so the processor cutouts match the socket
notches. See letter “A” in Figure 25.
8. Set the processor into place as shown by letter “B” in Figure 25.
A
B
AF000532
Figure 25. Installing the Processor
Note: Make sure the alignment triangle mark and the alignment triangle cutout align correctly.
9. Remove the protective socket cover. See Figure 26.
A
B
AF000530
Figure 26. Removing the Protective Socket Cover
Note: Retain the protective socket cover for use when removing a processor that will not be
replaced.
Intel® Server System SR1530SH/SR1530HSH User’s Guide
35
10. Lower the CPU load plate.
11. Lower the socket lever.
12. Install the heat sink. For instructions, see “Installing the Heat Sink”.
Installing the Heat Sink
Before installing the heat sink, you must install your processor. For instructions, see
“Installing the Processor” on page 34.
Caution: The heat sink has Thermal Interface Material (TIM) located on the bottom of it. Use
caution when you unpack the heat sink so you do not damage the TIM.
1. Remove the protective cover from the TIM on the underside of the heat sink. Do
not touch the TIM.
2. Orient the heat sink over the processor as shown in Figure 27. You must position
the fins as shown to provide correct airflow through the system.
3. Set the heat sink over the processor, lining up the four captive screws with the four
posts surrounding the processor.
4. Loosely screw in the captive screws on the heat sink corners in a diagonal manner
as shown by the four circled numbers in Figure 27. Do not fully tighten one screw
before tightening another.
5. Gradually and equally tighten each captive screw in the same order until each is
firmly tightened.
W
FLO
AIR
3
2
1
4
Ch
Fro assi
nt s
AF001049
Figure 27. Installing the Heat Sink
36
Intel® Server System SR1530SH/SR1530HSH User’s Guide
6. Reinstall and reconnect any parts you removed or disconnected to reach the
processor sockets.
7. Install the server system cover. For instructions, see “Installing the Server System
Cover”.
Installing and Removing a Hard Drive
(SR1530SH)
Caution: The hard drives are NOT hot-swappable. Before removing or replacing a hard drive, you
must first take the server out of service, turn off all peripheral devices connected to the
system, turn off the system by pressing the power button, and unplug the AC power cord
from the system or wall outlet.
You can install up to two SATA drives. The HDD0 drive bay is at the left side of the
chassis, underneath the optional CD-ROM drive. The HDD1 drive bay is at the right side
of the chassis. You do not need to install the drives in order; you can install HDD1 before
HDD0.
Note: The server system does not support all hard drives. See “Server System References” on
page x for an Internet link to a list of supported hardware.
Installing a Hard Disk Drive (SR1530SH)
Note: If you are replacing a hard drive, see “Removing a Hard Disk Drive (SR1530SH)” on
page 41 for instructions first. Return to these steps when directed.
1. Observe the safety and ESD precautions at the beginning of this book. See “Safety
Information” on page iii.
2. Power down the server. Unplug all peripheral devices and the AC power cable.
3. Remove the server system cover. For instructions, see “Removing the Server
System Cover” on page 24.
4. Locate the drive position you want to use. See Figure 28.
Intel® Server System SR1530SH/SR1530HSH User’s Guide
37
D
D
H
0
D
D
H
1
AF002322
Figure 28. Locating Drive Positions (SR1530SH)
5. HDD1 location only: Slide the power cables from the cable clip located on the top
of the hard drive carrier.
6. Remove the screw that holds the hard drive bracket to the chassis. See letter “A” in
Figure 29. Save this screw. You will use it to reinstall the drive assembly later.
7. Lift the drive carrier from the chassis. See letter “B” in Figure 29.
A
B
sis
as
Ch ont
Fr
AF001050
Figure 29. Removing Drive Carrier from the Server System (SR1530SH)
38
Intel® Server System SR1530SH/SR1530HSH User’s Guide
8. Position the drive with the drive connectors facing up as shown in Figure 30.
9. Set the drive carrier over the drive, as shown by the letter “A” in the figure. The
data and power connectors must be positioned so they are accessible through the
cut-out as shown by letter “B”.
10. Use the four screws provided to attach the drive to the carrier. See letter “C” in
Figure 30.
A
C
B
AF000668
Figure 30. Installing Drive into Drive Carrier (SR1530SH)
11. Set the drive assembly into place in the chassis. See letter “A” in Figure 31.
12. Attach the drive assembly to the chassis side with two screws. See letter “B” in
Figure 31.
13. Attach the drive assembly to the chassis with the screw you removed in Step 6. See
letter “C” in Figure 31.
Note: You must install the assembly that contains the optical drive bracket at the left side of the
system.
A
C
D
D
H
0
H
D
D
1
B
AF002323
Figure 31. Install Drive Assembly into the Server System (SR1530SH)
Intel® Server System SR1530SH/SR1530HSH User’s Guide
39
14. HDD1 only: Route the power cable into the cable clip on the top of the hard drive
bracket. See Figure 32.
15. Connect the data cables to the drive(s).
— Letter “A”: If a drive is installed in the HDD1 carrier, connect the HDD1 data
cable from the SATA 1 connector on the server board (letter “F”) to the hard
drive (letter “C”). See Figure 32.
— Letter “B”: If a drive is installed in the HDD0 carrier, connect the HDD0 data
cable from the SATA 0 connector on the server board (letter “F”) to the hard
drive (letter “C”). See Figure 32.
Note: The data cables are factory routed underneath the fan module (see letter “E”). Use
caution to make sure you connect the correct cables between the server board and the
hard drives. The cables are labeled at each end.
16. Connect the power cables to the drive(s):
— Letter “A”: If a drive is installed in the HDD1 carrier, attach the connector on
the daisy chain power cable that is closest to the power supply to the HDD1
connector. See letter “D” in Figure 32.
— Letter “B”: If a drive is installed in the HDD0 carrier, attach the middle
connector on the daisy chain power cable to the HDD0 power connector. See
letter “D” in Figure 32.
A
C
B
D
C
D
F
E
E
AF002324
Figure 32. Connecting Hard Drive Power and Data Cables (SR1530SH)
40
Intel® Server System SR1530SH/SR1530HSH User’s Guide
17. Install the server system cover. For instructions, see “Installing the Server System
Cover”.
Removing a Hard Disk Drive (SR1530SH)
1. Observe the safety and ESD precautions at the beginning of this book. See “Safety
Information” on page iii.
2. Power down the server and unplug all peripheral devices and the AC power cable.
3. Remove the server system cover. For instructions, see “Removing the Server
System Cover” on page 24.
4. Disconnect the power and data cables from the drive.
5. HDD1 location only: Slide the power cable from the cable clip located on the top of
the hard drive carrier.
6. Remove the screw that holds the hard drive bracket to the chassis. See letter “A” in
Figure 33. Save this screw. You will use it to reinstall the drive assembly later.
7. Lift the drive carrier from the chassis. See letter “B” in Figure 33.
A
B
sis
as
h
C ont
Fr
AF001050
Figure 33. Removing Drive Carrier from the Server System (SR1530SH)
8. Remove the four screws that attach the hard drive to the drive carrier. Lift the drive
from the carrier. Store the drive in an anti-static bag.
9. If you are installing a new drive, skip the rest of these steps and instead see
“Installing a Hard Disk Drive (SR1530SH)” on page 37, beginning with step 8.
10. Insert the screws that held the drive in the carrier into the screw locations on the
carrier for future use.
Intel® Server System SR1530SH/SR1530HSH User’s Guide
41
11. Set the drive assembly into place in the chassis.
12. Attach the drive assembly to the chassis with the screw that you removed in Step 6.
Note: You must install the assembly that contains the optical drive bracket at the left side of the
system.
13. Install the server system cover. For instructions, see “Installing the Server System
Cover”.
42
Intel® Server System SR1530SH/SR1530HSH User’s Guide
Installing and Removing a Hot-Swap SATA Drive
(SR1530HSH)
You can install up to three hot swappable SATA drives. The HDD0 drive bay is at the left
side of the chassis; the HDD1 drive bay is in the middle of the chassis—underneath the
optional optical drive. The HDD2 drive bay is at the right side of the chassis. You do not
need to install the drives in order; you can install HDD1 before HDD0.
Cautions: If you install less than three drives or devices, the empty drive bays must be occupied by
carriers with baffles to maintain proper system cooling.
Note: The server system does not support all hard drives. See “Server System References” on
page x for an Internet link to a list of supported hardware.
Installing a Hot-Swap SATA Drive (SR1530HSH)
1. If it is installed, remove the front bezel. For instructions, see “Removing the Front
Bezel”.
2. Locate the drive position you want to use. See Figure 34.
D
D
H
0
D
D
H
1
D
D
H
2
AF002325
Figure 34. Locating Drive Positions (SR1530HSH)
Intel® Server System SR1530SH/SR1530HSH User’s Guide
43
3. Open the latch at the front of the hard drive carrier. See letter "A" in Figure 35.
A
AF001583
Figure 35. Removing the Drive Carrier (SR1530HSH)
4. Pull out on the black lever and slide the carrier from the server system.
5. Remove the four screws that attach the plastic retention device or the previously
installed hard drive to the drive carrier. Two screws are at each side of the retention
device or the hard drive. Store the plastic retention device for future use. See letter
“A” in Figure 36.
6. Remove the hard drive from its wrapper and place it on an antistatic surface.
7. Set any jumpers and/or switches on the drive according to the drive manufacturer's
instructions.
8. With the drive circuit-side down, position the connector end of the drive so it is
facing the rear of the drive carrier.
9. Align the holes in the drive to the holes in the drive carrier and attach it to the
carrier with the screws that were attached to the plastic retention device. See letter
“B” in Figure 36.
A
B
AF001584
Figure 36. Installing Drive into Drive Carrier (SR1530HSH)
44
Intel® Server System SR1530SH/SR1530HSH User’s Guide
10. With the black lever in the fully open position, slide the drive assembly into the
server system (see letter “A” in Figure 37). The green latch at the front of the drive
carrier must be to the right. Do not push on the black drive carrier lever until the
lever begins to close by itself.
11. When the black drive carrier lever begins to close by itself, push on it to lock the
drive assembly into place (see letter “B” in Figure 37).
A
B
AF001585
Figure 37. Install Drive Assembly into the Server System (SR1530HSH)
12. Install the server system cover. For instructions, see “Installing the Server System
Cover”.
13. (Optional) Install the front bezel. For instructions, see “Installing the Front Bezel”.
14. Plug all peripheral devices and the AC power cable into the server.
Removing a Hot-Swap SATA Drive (SR1530HSH)
1. If it is installed, remove the front bezel. For instructions, see “Removing the Front
Bezel”.
2. Press in on the green latch at the front of the hard drive carrier.
3. Pull out on the black lever to slide the carrier from the server system.
4. Remove the four screws that attach the hard drive to the drive carrier. Lift the drive
from the carrier. Store the drive in an anti-static bag.
5. If you are not installing a new drive, place the plastic retention device into the drive
carrier, using the four screws you removed from the hard drive.
6. Insert the screws that held the drive in the carrier into the screw locations on the
carrier for future use.
7. With the black lever in the fully open position, slide the drive carrier into the server
system. The green latch must be to the right. Do not push on the black lever until
the lever begins to close by itself.
Intel® Server System SR1530SH/SR1530HSH User’s Guide
45
Note: For proper airflow, you must replace the hard drive carrier in the server system, even if no
hard drive is installed in it.
8. When the black lever begins to close by itself, push on it to lock the drive carrier
into place.
9. Install the server system cover. For instructions, see “Installing the Server System
Cover”.
10. (Optional) Install the front bezel. For instructions, see “Installing the Front Bezel”.
11. Plug all peripheral devices and the AC power cable into the server.
Installing or Removing a Slimline Optical Drive
(SR1530SH)
Caution: The optical drive is NOT hot-swappable. Before removing or replacing the optical drive,
you must first take the server out of service, turn off all peripheral devices connected to
the system, turn off the system by pressing the power button, and unplug the AC power
cord from the system or wall outlet.
Installing a Slimline Optical Drive
Notes:
• If you are replacing an optical drive, see “Removing a Slimline Optical Drive” on
page 49 for instructions first. Return to these steps when directed.
1. Observe the safety and ESD precautions at the beginning of this book. See “Safety
Information” on page iii.
2. Power down the server and unplug all peripheral devices and the AC power cable.
3. Remove the server system cover. For instructions, see “Removing the Server
System Cover” on page 24.
4. If it is installed, remove the bezel. For instructions, see “Removing the Front
Bezel” on page 22.
5. Note the orientation of the PCI cooling fan located behind the optical drive bay,
then disconnect the fan cable (see letter “A” in Figure 38) and lift the fan from the
mounting pegs (see letter “B” in Figure 38).
46
Intel® Server System SR1530SH/SR1530HSH User’s Guide
B
A
AF002326
Figure 38. Lifting PCI Cooling Fan from Mounting Pegs (SR1530SH)
6. First time installation only: Remove the knock-out by rocking it back and forth. See
letter “A” in Figure 39. You cannot reinstall the knock-out.
A
AF001174
Figure 39. Removing the Knock-out from the Sheet Metal Panel
7. Attach the optical drive to the brackets, using the four screws as shown in
Figure 40.
Intel® Server System SR1530SH/SR1530HSH User’s Guide
47
AF000672
Figure 40. Attaching the Optical Drive to the Brackets
8. Slide the optical drive assembly in through the front of the chassis, as shown by
letter “A in Figure 41.
9. Reinstall the screw that you removed in Step 6.
10. Connect the mini SATA power connector on the optical drive.
11. Connect the data cable to the optical drive and to the SATA connector on the server
board.
B
C
A
C
D
D
AF003095
Figure 41. Installing the Optical Drive into the System
48
Intel® Server System SR1530SH/SR1530HSH User’s Guide
12. SR1530SH: Insert the PCI cooling fan onto the mounting pegs located behind the
optical drive bay. The fan label should face the rear of the system. See letter “A” in
Figure 42.
13. SR1530SH: Connect the PCI cooling fan power cable to the fan connector on the
server board. See letter “B” in Figure 42.
A
B
AF002328
Figure 42. Installing the PCI Cooling Fan (SR1530SH)
14. (Optional) Install the front bezel. For instructions, see “Installing the Front Bezel”
on page 23.
15. Install the server system cover. For instructions, see “Installing the Server System
Cover”.
16. Plug all peripheral devices and the AC power cable into the server.
Removing a Slimline Optical Drive
1. Observe the safety and ESD precautions at the beginning of this book. See “Safety
Information” on page iii.
2. Power down the server and unplug all peripheral devices and the AC power cable.
3. Remove the server system cover. For instructions, see “Removing the Server
System Cover” on page 24.
4. If it is installed, remove the bezel. For instructions, see “Removing the Front
Bezel” on page 22.
5. SR1530SH: Note the orientation of the PCI cooling fan located behind the optical
drive bay, then disconnect the fan cable (see letter “A” in Figure 43) and lift the fan
from the mounting pegs (see letter “B” in Figure 43).
Intel® Server System SR1530SH/SR1530HSH User’s Guide
49
B
A
AF002326
Figure 43. Lifting PCI Cooling Fan from Mounting Pegs (SR1530SH)
6. Disconnect the optical drive power and data cables. See letters “A” and “B” in
Figure 44.
7. Remove the screw that holds the optical drive bracket to the server chassis. See
letter “C” in Figure 44. Save this screw. You will reinstall it later.
8. Slide the optical drive out through the front of the system. See letter “D” in
Figure 44.
C
D
B
A
AF000670
Figure 44. Removing the Optical Drive from the Server System
50
Intel® Server System SR1530SH/SR1530HSH User’s Guide
9. Remove the four screws that hold the optical drive to the brackets as shown in
Figure 45. Save these screws for future use.
AF000672
Figure 45. Removing the Optical Drive Brackets
10. If you are installing a replacement optical drive, skip the rest of these steps and
instead continue with "Installing a Slimline Optical Drive", Step 7 on page 47.
11. Store the brackets for future use.
12. SR1530SH: Insert the PCI cooling fan onto the mounting pegs located behind the
optical drive bay (see letter “A” in Figure 46). The fan label should face the rear of
the system. Connect the fan cable to the connector on the server board (see letter
“B” in Figure 46).
A
B
AF002328
Figure 46. Installing the PCI Cooling Fan (SR1530SH)
Intel® Server System SR1530SH/SR1530HSH User’s Guide
51
13. (Optional) Install the front bezel. For instructions, see “Installing the Front Bezel”
on page 23.
14. Install the server system cover. For instructions, see “Installing the Server System
Cover”.
Installing or Removing a Slimline Optical Drive
(SR1530HSH)
Caution: The optical drive is NOT hot-swappable. Before removing or replacing the optical drive,
you must first take the server out of service, turn off all peripheral devices connected to
the system, turn off the system by pressing the power button, and unplug the AC power
cord from the system or wall outlet.
Installing a Slimline Optical Drive (SR1530HSH)
Note: The hardware necessary to install your optical drive was shipped to you in a bag labeled
“CD-ROM Assy”.
1. Observe the safety and ESD precautions at the beginning of this book. See “Safety
Information” on page iii.
2. Power down the server and unplug all peripheral devices and the AC power cable.
3. Remove the server system cover. For instructions, see “Removing the Server
System Cover” on page 24.
4. Remove the bezel if it is installed. For instructions, see “Removing the Front
Bezel” on page 22.
5. First time installation only: Remove the peripheral knock-out by rocking it back
and forth.
6. Attach the optical drive attachment bracket as shown in Figure 47.
52
Intel® Server System SR1530SH/SR1530HSH User’s Guide
A
AF001643
Figure 47. Attaching the Optical Drive to the Attachment Bracket
7. Slide the optical drive assembly in through the front of the chassis (see letter “A” in
Figure 48).
8. Install the screws to lock the drive in place (see letters “B” and “C” in Figure 48).
B
C
A
AF001636
Figure 48. Installing the Optical Drive into the System
9. (Optional) Install the front bezel. For instructions, see “Installing the Front Bezel”
on page 23.
10. Install the server system cover. For instructions, see “Installing the Server System
Cover”.
Removing a Slimline Optical Drive (SR1530HSH)
1. Observe the safety and ESD precautions at the beginning of this book. See “Safety
Information” on page iii.
2. Power down the server and unplug all peripheral devices and the AC power cable.
Intel® Server System SR1530SH/SR1530HSH User’s Guide
53
3. Remove the server system cover. For instructions, see “Removing the Server
System Cover” on page 24.
4. If it is installed, remove the bezel. For instructions, see “Removing the Front
Bezel” on page 22.
5. Remove the screws holding the drive in place (see letters “A” and “B” in Figure 49)
and slide the optical drive assembly out through the front of the chassis (see letter
“C” in Figure 49).
A
B
C
AF001635
Figure 49. Removing the Optical Drive from the System
6. Remove the optical drive attachment bracket as shown in Figure 50.
A
AF001644
Figure 50. Removing the Optical Drive from the Attachment Bracket
7. (Optional) Install the front bezel. For instructions, see “Installing the Front Bezel”
on page 23.
8. Install the server system cover. For instructions, see “Installing the Server System
Cover”.
54
Intel® Server System SR1530SH/SR1530HSH User’s Guide
Installing and Removing the PCIe* Riser
Assembly
Caution: The PCIe* riser assembly is NOT hot-swappable. Before removing or replacing the PCIe*
riser assembly, you must first take the server out of service, turn off all peripheral devices
connected to the system, turn off the system by pressing the power button, and unplug the
AC power cord from the system or wall outlet.
Removing the PCIe* Riser Assembly
To remove the PCIe* riser assembly, use the following instructions.
1. Observe the safety and ESD precautions at the beginning of this book. See “Safety
Information” on page iii.
2. Power down the server and unplug all peripheral devices and the AC power cable.
3. Remove the server system cover. For instructions, see “Removing the Server
System Cover” on page 24.
4. Disconnect any cables attached to any add-in cards.
5. Lift riser assembly up to remove it. Use caution to gently ease the riser card from
the add-in card slot so you do not damage the slot or the riser card. See Figure 51.
AF002329
Figure 51. Removing PCIe* Riser Assembly from the Server System
Intel® Server System SR1530SH/SR1530HSH User’s Guide
55
6. If you need to add or replace a PCIe* Riser connector, see “Installing or Replacing
a PCIe* Riser Card” on page 57.
7. If you need to add or replace a PCI add-in card, see “Installing and Removing a PCI
Add-in Card” on page 59.
8. If you removed the PCIe* Riser assembly for another procedure, continue with that
procedure.
Installing the PCIe* Riser Assembly
Note: For clarity, the figures in this series of instructions does not show an attached add-in
card. If you are installing an add-in card, do so before installing the PCIe* riser assembly
into your server system.
1. Lower the riser assembly into place over the add-in card slot. See letter “A” in
Figure 52.
2. Align the three hooks in the riser assembly with the matching slots at the back of
the server system. See letter “B” in Figure 52.
AF002330
Figure 52. Installing PCIe* Riser Assembly into the Server System
3. Press down uniformly until the two hooks on the rear of the PCIe* riser assembly
engage the server system back panel slots. The riser cards will seat into the
matching sockets on the server board.
4. Connect any cables to add-in cards that require them. See your add-in card
documentation for information and add-in card requirements.
56
Intel® Server System SR1530SH/SR1530HSH User’s Guide
5. Install the server system cover. For instructions, see “Installing the Server System
Cover”.
Installing or Replacing a PCIe* Riser Card
Caution: The PCIe* Riser card is NOT hot-swappable. Before removing or replacing the PCIe*
Riser card, you must first take the server out of service, turn off all peripheral devices
connected to the system, turn off the system by pressing the power button, and unplug the
AC power cord from the system or wall outlet.
You have the option to install one of two PCIe* Riser cards into your server system:
• A low-profile PCI Express* riser with one PCI Express x16 slot.
Note: To eliminate the possibility of installing the replacement connector on the wrong side of
the PCIe* Riser assembly, replace one connector at a time.
Removing a PCIe* Riser Card
1. Observe the safety and ESD precautions at the beginning of this book. See “Safety
Information” on page iii.
2. Power down the server and unplug all peripheral devices and the AC power cable.
3. Remove the server system cover. For instructions, see “Removing the Server
System Cover” on page 24.
4. Disconnect any cables attached to any add-in cards.
5. Remove the PCIe* Riser assembly. For instructions, see “Removing the PCIe*
Riser Assembly” on page 55.
6. Remove any add-in cards from the PCIe* Riser connector. For instructions, see
“Removing a PCI Add-in Card” on page 60.
7. Remove the two screws that attach the riser card to the riser assembly. See
Figure 53. Save these screws to be used later.
AF001061
Figure 53. Removing Riser Card from Riser Assembly
Intel® Server System SR1530SH/SR1530HSH User’s Guide
57
8. Install the replacement riser connector, if desired. For instructions, see “Installing a
PCIe* Riser Card” on page 58.
9. Install the PCIe* Riser assembly into the server system. For instructions, see
“Installing the PCIe* Riser Assembly” on page 56.
10. Install the server system cover. For instructions, see “Installing the Server System
Cover”.
11. Plug all peripheral devices and the AC power cable into the server.
Installing a PCIe* Riser Card
1. Observe the safety and ESD precautions at the beginning of this book. See “Safety
Information” on page iii.
2. Power down the server and unplug all peripheral devices and the AC power cable.
3. Remove the server system cover. For instructions, see “Removing the Server
System Cover”.
4. Disconnect any cables attached to any add-in cards.
5. Remove the PCIe* Riser assembly. For instructions, see “Removing the PCIe*
Riser Assembly” on page 55.
6. Remove any add-in cards from the PCIe* Riser connector. For instructions, see
“Removing a PCI Add-in Card” on page 60.
7. Use two screws to attach the riser card to the riser assembly. See Figure 54.
AF001060
Figure 54. Installing Riser Card onto Riser Assembly
8. Install an PCI add-in card if desired. For instructions, see “Installing a PCI Add-in
Card” on page 59.
9. Install the PCIe* Riser assembly into the server system. For instructions, see
“Installing the PCIe* Riser Assembly” on page 56.
58
Intel® Server System SR1530SH/SR1530HSH User’s Guide
10. Connect any cables to add-in cards that require them. See your add-in card
documentation for information and add-in card requirements.
11. Re-install the processor air duct. For instructions, see “Installing the Processor Air
Duct” on page 29.
12. Install the server system cover. For instructions, see “Installing the Server System
Cover”.
13. Plug all peripheral devices and the AC power cable into the server.
Installing and Removing a PCI Add-in Card
Caution: The add-in cards are NOT hot-swappable. Before removing or replacing an add-in card,
you must first take the server out of service, turn off all peripheral devices connected to
the system, turn off the system by pressing the power button, and unplug the AC power
cord from the system or wall outlet.
Installing a PCI Add-in Card
1. Observe the safety and ESD precautions at the beginning of this book. See “Safety
Information” on page iii.
2. Power down the server and unplug all peripheral devices and the AC power cable.
3. Remove the server system cover. For instructions, see “Removing the Server
System Cover” on page 24.
4. Remove the PCIe* Riser assembly. For instructions, see “Removing the PCIe*
Riser Assembly” on page 55.
Intel® Server System SR1530SH/SR1530HSH User’s Guide
59
5. Remove the screw at the rear of the riser assembly. See letter “A” in Figure 55.
Save this screw. You will reinstall it later.
6. If a filler panel is installed over the opening at the rear of the riser assembly, lift it
from the riser assembly. See letter “B” in Figure 55. Save the filler panel in case
you later need to remove the add-in card.
7. Insert the add-in card into the socket in the riser assembly. Push the add-in card into
place firmly until it seats in the riser card connector, but use caution so you do not
twist or bend the card. See letter “C” in Figure 55.
8. Re-install the screw you removed in Step 5. See letter “A” in Figure 55.
B
C
A
AF000674
Figure 55. Installing an Add-In Card
9. Install the PCIe* Riser assembly into the server system. For instructions, see
“Installing the PCIe* Riser Assembly” on page 56.
10. Install the server system cover. For instructions, see “Installing the Server System
Cover”.
11. Plug all peripheral devices and the AC power cable into the server.
Removing a PCI Add-in Card
1. Observe the safety and ESD precautions at the beginning of this book. See “Safety
Information” on page iii.
2. Power down the server and unplug all peripheral devices and the AC power cable.
3. Remove the server system cover. For instructions, see “Removing the Server
System Cover” on page 24.
4. Remove the PCIe* Riser assembly. For instructions, see “Removing the PCIe*
Riser Assembly” on page 55.
60
Intel® Server System SR1530SH/SR1530HSH User’s Guide
5. Remove the screw at the rear of the riser assembly. See letter “A” in Figure 56.
Save this screw. You will use it later.
6. Pull the add-in card from the socket in the riser assembly. You may need to wriggle
the card from front to back to remove it, but use caution so you do not twist or bend
the card. See letter “B” in Figure 56.
7. Install a filler panel over the opening at the rear of the riser assembly. See letter “C”
in Figure 56.
8. Re-install the screw you removed in step 5. See letter “A” in Figure 56.
C
B
A
AF000675
Figure 56. Removing a Full Height Add-In Card
Note: Make sure that all empty add-in card slots have filler panels installed.
9. Install the PCIe* Riser assembly into the server system. For instructions, see
“Installing the PCIe* Riser Assembly” on page 56.
10. Install the processor air duct. For instructions, see “Installing the Processor Air
Duct” on page 29.
11. Install the server system cover. For instructions, see “Installing the Server System
Cover”.
12. Plug all peripheral devices and the AC power cable into the server.
Intel® Server System SR1530SH/SR1530HSH User’s Guide
61
Replacing the Server Board
Removing the Server Board
1. Observe the safety and ESD precautions at the beginning of this book. See “Safety
Information” on page iii.
2. Power down the server and unplug all peripheral devices and the AC power cable.
3. Remove the server system cover. For instructions, see “Removing the Server
System Cover” on page 24.
4. Remove the processor air duct. For instructions, see “Removing the Processor Air
Duct” on page 27.
5. Remove the PCIe* Riser assembly. For instructions, see “Removing the PCIe*
Riser Assembly” on page 55.
6. Detach all cables connected to the server board.
7. Remove the heat sink and the processor. For instructions, see “Removing the Heat
Sink and Processor” on page 33.
8. Remove the DIMMs. For instructions, see “Removing DIMMs” on page 32.
62
Intel® Server System SR1530SH/SR1530HSH User’s Guide
9. Remove the nine screws from the server board (see letter “A”) and lift the server
board from the server system (see letter “B”).
A
B
AF002331
Figure 57. Removing the Server Board
10. Replace the server board. For instructions, see “Installing the Server Board” on
page 64.
11. Install the processor. For instructions, see “Installing the Processor” on page 34.
12. Install the DIMMs. For instructions, see “Installing DIMMs” on page 31.
13. Install the PCIe* Riser assembly. For instructions, see “Installing the PCIe* Riser
Assembly” on page 56.
14. Reconnect all cables to the server board. For a full cabling diagram, see Figure 80
on page 88.
15. Install the processor air duct. For instructions, see “Installing the Processor Air
Duct” on page 29.
16. Install the server system cover. For instructions, see “Installing the Server System
Cover”.
Intel® Server System SR1530SH/SR1530HSH User’s Guide
63
17. Plug all peripheral devices and the AC power cable into the server.
Installing the Server Board
1. Observe the safety and ESD precautions at the beginning of this book. See “Safety
Information” on page iii.
2. Power down the server and unplug all peripheral devices and the AC power cable.
3. Remove the server system cover. For instructions, see “Removing the Server
System Cover” on page 24.
4. Remove the processor air duct. For instructions, see “Removing the Processor Air
Duct” on page 27.
5. Remove the PCIe* Riser assembly. For instructions, see “Removing the PCIe*
Riser Assembly” on page 55.
6. Place the server board into the server system as shown by letter “A” in Figure 58.
7. Attach the server board with nine screws. See letter “B” in Figure 58.
B
A
AF002332
Figure 58. Installing the Server Board
64
Intel® Server System SR1530SH/SR1530HSH User’s Guide
8. Install the processor and the heat sink. For instructions, see “Installing the
Processor” on page 34.
9. Install the system memory. For instructions, see “Installing DIMMs” on page 31.
10. Connect the data cables. For data cable routing information, see “Cable Routing”
on page 87.
11. Connect the power cables. For power cable routing information, see “Cable
Routing” on page 87.
12. Install the PCIe* Riser assembly. For instructions, see “Installing the PCIe* Riser
Assembly” on page 56.
13. Install the processor air duct. For instructions, see “Installing the Processor Air
Duct” on page 29.
14. Install the server system cover. For instructions, see “Installing the Server System
Cover”.
15. Plug all peripheral devices and the AC power cable into the server.
Replacing the CMOS Battery
Caution: The CMOS battery is NOT hot-swappable. Before removing or replacing the CMOS
battery, you must first take the server out of service, turn off all peripheral devices
connected to the system, turn off the system by pressing the power button, and unplug the
AC power cord from the system or wall outlet.
The lithium battery on the server board powers the RTC in the absence of power. When
the battery starts to weaken, it loses voltage, and the server settings stored in CMOS RAM
in the RTC (for example, the date and time) may be wrong. For a list of approved devices,
contact your customer service representative or dealer.
Warning: Danger of explosion if battery is incorrectly replaced. Replace only with the same or
equivalent type recommended by the equipment manufacturer. Discard used batteries
according to manufacturer's instructions.
Advarsel: Lithiumbatteri - Eksplosionsfare ved fejlagtig håndtering. Udskiftning må kun ske med
batteri af samme fabrikat og type. Levér det brugte batteri tilbage til leverandøren.
Advarsel: Lithiumbatteri - Eksplosjonsfare. Ved utskifting benyttes kun batteri som anbefalt av
apparatfabrikanten. Brukt batteri returneres apparatleverandøren.
Varning: Explosionsfara vid felaktigt batteribyte. Använd samma batterityp eller en ekvivalent typ
som rekommenderas av apparattillverkaren. Kassera använt batteri enligt fabrikantens
instruktion.
Varoitus: Paristo voi räjähtää, jos se on virheellisesti asennettu. Vaihda paristo ainoastaan
laitevalmistajan suosittelemaan tyyppiin. Hävitä käytetty paristo valmistajan ohjeiden
mukaisesti.
Intel® Server System SR1530SH/SR1530HSH User’s Guide
65
1. Observe the safety and ESD precautions at the beginning of this book. See “Safety
Information” on page iii.
2. Power down the server and unplug all peripheral devices and the AC power cable.
3. Remove the server system cover. For instructions, see “Removing the Server
System Cover” on page 24.
4. Remove the server's cover and locate the battery. See Figure 59.
5. Pull back gently on the metal tab at the top of the battery.
6. Remove the battery from its socket.
AF002308
Figure 59. Replacing the CMOS Battery
7. Dispose of the battery according to local ordinance.
8. Remove the new lithium battery from its package, and, being careful to observe the
correct polarity, insert it in the battery socket.
9. Close the chassis.
10. Run the BIOS Setup utility to restore the configuration settings.
66
Intel® Server System SR1530SH/SR1530HSH User’s Guide
Replacing the Power Supply (SR1530SH)
Caution: The power supply is NOT hot-swappable. Before removing or replacing the power supply,
you must first take the server out of service, turn off all peripheral devices connected to
the system, turn off the system by pressing the power button, and unplug the AC power
cord from the system or wall outlet.
You can replace the power supply if it fails or if one of the integrated fans in it fails. To
replace the power supply, use the following instructions.
1. Observe the safety and ESD precautions at the beginning of this book. See “Safety
Information” on page iii.
2. Power down the server and unplug all peripheral devices and the AC power cable.
3. Remove the server system cover. For instructions, see “Removing the Server
System Cover”.
4. Disconnect all power cables connected to the server board and peripherals. See
Figure 60:
— A: 2x4 power connector
— B: 2x12 main power connector
— C: Daisy-chain cable to:
✧ Optical drive power connector, if an optical drive is installed
✧ HDD0 power connector, if a hard drive is installed here
✧ HDD1 power connector, if a hard drive is installed here
Intel® Server System SR1530SH/SR1530HSH User’s Guide
67
.
A
B
C
D
E
AF002473
Figure 60. Disconnecting Power Cables (SR1530SH)
68
Intel® Server System SR1530SH/SR1530HSH User’s Guide
5. Remove the screw at the back of the server system, next to the AC power input.
Save this screw. You will re-insert it later. See letter “A” in Figure 61.
6. Lift up slightly on the front of the power supply until it clears the foot at the bottom
of the chassis. See letter “B” in Figure 61.
7. Slide the power supply forward (see letter “C”) and then lift it from the chassis.
A
B
C
B
AF002474
Figure 61. Removing Power Supply from the Server System (SR1530SH)
Intel® Server System SR1530SH/SR1530HSH User’s Guide
69
8. Insert the replacement power supply at an angle into the server system, sliding the
power connector side in first to fit it through the cut-out area at the rear of the
system. See letter “A” in Figure 62.
9. Set the front of the power supply down pushing the power supply back so it fits
behind the foot at the bottom of the chassis. See letter “B” in Figure 62.
10. Insert the screw you removed in Step 5 to attach the power supply to the server
system. See letter “C” in Figure 62.
C
B
A
B
AF002475
Figure 62. Installing Power Supply Module into the Server System
(SR1530SH)
70
Intel® Server System SR1530SH/SR1530HSH User’s Guide
11. Connect the power supply cables to the server board and peripherals. See Figure 62.
— A: 2x4 power connector
— B: 2x12 main power connector
— C: Daisy chain cable to:
✧ HDD1 power connector, if a hard drive is installed here. Use the connector on
cable that is closest to power supply.
✧ HDD0 power connector, if a hard drive is installed here. Use the center
connector on the cable.
✧ Optical drive power, if an optical drive is installed. Use the end connector on
the power supply.
.
A
B
C
D
E
AF002476
Figure 63. Connecting Power Cables (SR1530SH)
12. Install the server system cover. For instructions, see “Installing the Server System
Cover”.
13. Plug all peripheral devices and the AC power cable into the server.
Intel® Server System SR1530SH/SR1530HSH User’s Guide
71
Replacing the Power Supply (SR1530HSH)
Caution: The power supply is NOT hot-swappable. Before removing or replacing the power supply,
you must first take the server out of service, turn off all peripheral devices connected to
the system, turn off the system by pressing the power button, and unplug the AC power
cord from the system or wall outlet.
You can replace the power supply if it fails or if one of the integrated fans in it fails. To
replace the power supply, use the following instructions.
1. Observe the safety and ESD precautions at the beginning of this book. See “Safety
Information” on page iii.
2. Power down the server and unplug all peripheral devices and the AC power cable
(see letter “A” in Figure 64).
3. Remove the server system cover. For instructions, see “Removing the Server
System Cover”.
4. Disconnect all power cables connected to the server board and peripherals.
5. Lift up slightly on the front of the power supply until it clears the foot at the bottom
of the chassis (see letter “B” in Figure 64).
6. Slide the power supply forward (see letter “C” in Figure 64) and then lift it from the
chassis.
A
B
C
B
AF002477
Figure 64. Removing Power Supply from the Server System (SR1530HSH)
72
Intel® Server System SR1530SH/SR1530HSH User’s Guide
7. Insert the replacement power supply at an angle into the server system, sliding the
power connector side in first to fit it through the cut-out area at the rear of the
system (see letter “A” in Figure 65).
8. Set the front of the power supply down pushing the power supply back so it fits
behind the foot at the bottom of the chassis (see letter “B” in Figure 65).
C
B
A
AF002478
Figure 65. Installing Power Supply Module into the Server System
(SR1530HSH)
9. Connect the power supply cables to the server board and peripherals.
10. Install the server system cover. For instructions, see “Installing the Server System
Cover”.
11. Plug all peripheral devices and the AC power cable into the server (see letter “C” in
Figure 65).
Intel® Server System SR1530SH/SR1530HSH User’s Guide
73
Replacing the Front Panel Board (SR1530SH)
Caution: The front panel is NOT hot-swappable. Before removing or replacing the front panel, you
must first take the server out of service, turn off all peripheral devices connected to the
system, turn off the system by pressing the power button, and unplug the AC power cord
from the system or wall outlet.
You must operate your server with a front panel installed.
1. Observe the safety and ESD precautions at the beginning of this book. See “Safety
Information” on page iii.
2. Power down the server and unplug all peripheral devices and the AC power cable.
3. Remove the server system cover. For instructions, see “Removing the Server
System Cover” on page 24.
4. Disconnect the power and data cables connected to HDD1, at the right side of the
system. It is not necessary to remove the HDD1 drive.
5. Disconnect the front panel cable, the USB cable, and power cable from the front
panel board (see letters “A”, “B”, and “C”).
6. Remove the two screws that attach the front panel board to the server system. See
letter “D” in Figure 66. Save these screws. You will re-install them later.
7. Lift the front panel board from the system. See letter “E” in Figure 66.
A
B
C
D
E
AF002479
Figure 66. Removing Front Panel Board from the Server System (SR1530SH)
74
Intel® Server System SR1530SH/SR1530HSH User’s Guide
8. Insert the replacement front panel board into the server system over the two
standoffs. Press down gently until the board clicks into place (see letter “A” in
Figure 67).
9. Use the two screws you removed in Step 7 to attach the front panel board to the
system (see letter “B” in Figure 67).
10. Connect the USB floppy cable if you removed it in Step 6.
11. Connect the USB cable and the front panel cable.
12. Connect the HDD1 power and data cables.
B
A
AF002480
Figure 67. Installing Front Panel Board into the Server System (SR1530SH)
13. Install the server system cover. For instructions, see “Installing the Server System
Cover”.
14. Plug all peripheral devices and the AC power cable into the server.
Intel® Server System SR1530SH/SR1530HSH User’s Guide
75
Replacing the Front Panel Board (SR1530HSH)
Caution: The front panel is NOT hot-swappable. Before removing or replacing the front panel, you
must first take the server out of service, turn off all peripheral devices connected to the
system, turn off the system by pressing the power button, and unplug the AC power cord
from the system or wall outlet.
You must operate your server with a front panel installed.
1. Observe the safety and ESD precautions at the beginning of this book. See “Safety
Information” on page iii.
2. Power down the server and unplug all peripheral devices and the AC power cable.
3. Remove the server system cover. For instructions, see “Removing the Server
System Cover” on page 24.
4. Disconnect the front panel cable and the USB cable from the front panel board.
5. Remove the screw that attaches the front panel board to the server system. See
letter “A” in Figure 68. Save the screw. You will re-install it later.
6. Slide the front panel board back (see letter “B” in Figure 68) and lift the front panel
board from the system (see letter “C” in Figure 68).
A
B
C
AF001589
Figure 68. Removing Front Panel Board from the Server System
(SR1530HSH)
76
Intel® Server System SR1530SH/SR1530HSH User’s Guide
7. Remove the light pipes from the front panel board by lifting straight up (see letters
“A” and “B” in Figure 69). You will use these in the replacement front panel board.
B
A
AF001660
Figure 69. Removing Light Pipes from the Front Panel Board (SR1530HSH)
8. Insert the replacement front panel board into the server system over the standoff
(see letter “A” in Figure 70) and slide the front panel board forward until the board
clicks into place (see letter “B” in Figure 70).
9. Use the screw you removed in Step 5 to attach the front panel board to the system
(see letter “C” in Figure 70).
C
B
A
AF001590
Figure 70. Installing Front Panel Board into the Server System (SR1530HSH)
Intel® Server System SR1530SH/SR1530HSH User’s Guide
77
10. Install the light pipes on the front panel board as shown in Figure 71. Install the
light pipe set closer to the outside of the chassis first (see letter “A” in Figure 71),
and then install the second light pipe set (see letter “B” in Figure 71).
A
B
AF001661
Figure 71. Installing Light Pipes on the Front Panel Board (SR1530HSH)
11. Connect the USB floppy cable if you removed it in Step 4.
12. Connect the front panel cable.
13. Install the server system cover. For instructions, see “Installing the Server System
Cover”.
14. Plug all peripheral devices and the AC power cable into the server.
78
Intel® Server System SR1530SH/SR1530HSH User’s Guide
Replacing a System Fan (SR1530SH)
Caution: The fans are NOT hot-swappable. Before removing or replacing a fan, you must first take
the server out of service, turn off all peripheral devices connected to the system, turn off
the system by pressing the power button, and unplug the AC power cord from the system
or wall outlet.
Note: You cannot replace the fans integrated into the power supply separately. If one of the fans
in the power supply fails, you must replace the power supply.
If one of the blower fans fails, you can individually replace them. If a fan in the power
supply fails, you must replace the power supply. Use the following steps to replace a
system blower fan or the PCI cooling fan.
Replacing the System Blower Fans (SR1530SH)
1. Observe the safety and ESD precautions at the beginning of this book. See “Safety
Information” on page iii.
2. Power down the server and unplug all peripheral devices and the AC power cable.
3. Remove the server system cover. For instructions, see “Removing the Server
System Cover”.
4. Remove the processor air duct (see letter “A” in Figure 72). For instructions, see
“Removing the Processor Air Duct” on page 27.
5. Disconnect the two fan cables from the server board (see letter “B” in Figure 72)
and untie the cable tie (see letter “C” in Figure 72).
A
B
C
AF002481
Figure 72. Disconnecting System Blower Fans (SR1530SH)
Intel® Server System SR1530SH/SR1530HSH User’s Guide
79
6. Remove the three screws that hold the fan bracket in place. Save these screws. You
will re-install them later. See letter “A” in Figure 73.
7. Remove the fan cable from beneath the clip at the front of the fan bracket. See letter
“B” in Figure 73.
8. Lift the fan bracket from the server. Lift the bracket at an angle, front of the bracket
first, to clear the hard disk drive brackets. See letter “C” in Figure 73.
A
C
B
AF002482
Figure 73. Removing Bracket and System Blower Fans from Server System
(SR1530SH)
80
Intel® Server System SR1530SH/SR1530HSH User’s Guide
9. Turn the bracket over and remove the two screws that attach the failed fan to the
bracket. Save these screws. You will reinstall them later. See letter “A” in
Figure 74.
10. Lift the fan from the bracket. See letter “B” in Figure 74.
B
A
AF000963
Figure 74. Removing Fan from Fan Bracket (SR1530SH)
11. Install the replacement fan onto the bracket, using the two screws you removed in
Step 9.
12. Set the fan assembly into the system. Insert the rear edge first and push the
assembly slightly rearward to clear the hard disk drive brackets. Use caution to
make sure you do not pinch any cables.
13. Route the cable from the fan at the right around the right side of the assembly and
under the clip at the front of the fan bracket.
Intel® Server System SR1530SH/SR1530HSH User’s Guide
81
14. Connect the fans to the server board. See letters “A” and “B” in Figure 75.
B
A
AF002483
Figure 75. Connecting System Blower Fans (SR1530SH)
15. Install the processor air duct. For instructions. see “Installing the Processor Air
Duct” on page 29.
82
Intel® Server System SR1530SH/SR1530HSH User’s Guide
Replacing a System Fan (SR1530HSH)
Caution: The fans are NOT hot-swappable. Before removing or replacing a fan, you must first take
the server out of service, turn off all peripheral devices connected to the system, turn off
the system by pressing the power button, and unplug the AC power cord from the system
or wall outlet.
Note: You cannot replace the fans into the power supply separately. If one of the fans in the
power supply fails, you must replace the power supply.
If one of the blower fans fails, you can individually replace them. If a fan in the power
supply fails, you must replace the power supply. Use the following steps to replace a
system blower fan or the PCI cooling fan.
Replacing the System Blower Fans (SR1530HSH)
1. Observe the safety and ESD precautions at the beginning of this book. See “Safety
Information” on page iii.
2. Power down the server and unplug all peripheral devices and the AC power cable.
3. Remove the server system cover. For instructions, see “Removing the Server
System Cover”.
4. Remove the processor air duct (see letter “A” in the figure below). For instructions,
see “Removing the Processor Air Duct” on page 27.
5. Remove the two screws that hold the fan in place. Save these screws. You will reinstall them later.
6. Disconnect the fan cable from the server board (see letter “B” in Figure 76).
Intel® Server System SR1530SH/SR1530HSH User’s Guide
83
7. Lift the fan from the system (see letter “C” in Figure 76).
B
A
C
AF001633
Figure 76. Removing Fan from the Server System (SR1530HSH)
8. Install the replacement fan into the chassis (see letter “A” in Figure 77), using the
two screws you removed previously.
9. Connect the fan cable to the server board (see letter “B” in Figure 77).
10. Install the processor air duct (see letter “C” in Figure 77).
B
C
A
AF001634
Figure 77. Installing Fan into the Server System (SR1530HSH)
11. Install the server system cover. For instructions, see “Installing the Server System
Cover”.
12. Plug all peripheral devices and the AC power cable into the server.
84
Intel® Server System SR1530SH/SR1530HSH User’s Guide
Installing and Removing the Rack Handles
Installing the Rack Handles
1. Observe the safety and ESD precautions at the beginning of this book. See “Safety
Information” on page iii.
2. Power down the server and unplug all peripheral devices and the AC power cable.
3. If it is installed, remove the front bezel if it is installed. For instructions, see
“Removing the Front Bezel” on page 22.
4. Attach the rack handle to the server system with two screws as shown in Figure 78.
AF001204
Figure 78. Installing the Rack Handle
5. Repeat Step 4 on the opposite side of the server.
6. (Optional) Install the front bezel, if desired. For instructions, see “Installing the
Front Bezel” on page 23.
7. Plug all peripheral devices and the AC power cable into the server.
Intel® Server System SR1530SH/SR1530HSH User’s Guide
85
Removing the Rack Handles
1. Observe the safety and ESD precautions at the beginning of this book. See “Safety
Information” on page iii.
2. Power down the server and unplug all peripheral devices and the AC power cable.
3. If it is installed, remove the front bezel. For instructions, see “Removing the Front
Bezel” on page 22.
4. Remove the two screws holding the rack handle in place, and remove the rack
handle from the server system as shown in Figure 79.
AF001204
Figure 79. Removing the Rack Handle
5. Repeat Step 4 on the opposite side of the system.
6. (Optional) Install the front bezel, if desired. For instructions, see “Installing the
Front Bezel” on page 23.
7. Plug all peripheral devices and the AC power cable into the server.
86
Intel® Server System SR1530SH/SR1530HSH User’s Guide
Appendix A: Technical Reference
Cable Routing
When you add or remove components from your server system, make sure your cables are
routed correctly before reinstalling the server system cover. Use caution to make sure no
cables or wires are pinched and that the airflow from the fans is not blocked. Use the
following figures to determine the correct cable routing.
For readability, separate figures for power cable routing and data cable routing are
included. Make sure all necessary power and data cables are connected and routed as
shown. Dashed lines in the drawings indicate a location where a cable is routed beneath a
component and each connector end is labeled with the same letter. For example, the PCI
cooling fan cable is labeled with the letter “C” both where it connects to the server board
and at the PCI cooling fan itself.
Intel® Server System SR1530SH/SR1530HSH User’s Guide
87
Power Cable Routing (SR1530SH)
A
B
H
G
F
C
D
E
AF002484
A.
Processor power
D.
Right system blower fan
B.
Main power
E.
Left system blower fan
C.
PCI cooling fan
F.
Drive power daisy cable
F1: Connector closest to power supply to HDD1
F2: Center connector to HDD0
F3: End connector to optical drive
–
–
–
Figure 80. Power Cable Routing (SR1530SH)
Note: The power cable to the two hard drives and the optical drive is a single daisy chain cable.
To make Figure 80 more clear, where the connectors attach to the components, the labels
“F1”, “F2”, and “F3” are used. The end at the power supply itself is labeled “F”.
88
Intel® Server System SR1530SH/SR1530HSH User’s Guide
Data Cable Routing (SR1530SH)
A
C
D
B
E
AF002485
A.
Front panel USB
D.
SATA 0 to HDD0
B.
Front panel
E.
Optical drive
C.
SATA 1 to HDD1
Figure 81. Data Cable Routing (SR1530SH)
Intel® Server System SR1530SH/SR1530HSH User’s Guide
89
Cable Routing (SR1530HSH)
A
B
B
CPU
D
A
E
F
G
C
H
D
I
F
C
J
K
F
G
F
A
B
Server Board
C
D
E
Blower Fan #1
F
G
Hard Disk Drive Bays
H
A
B
Optical Drive
C
D
E
F
G
H
I
J
K
Power to Backplane
Power Supply
Blower Fan #2
Front Panel Board
Backplane
Power to Server Board (Main)
Power to Server Board (CPU)
Front Panel USB
Front Panel
Blower Fan #1 Power
Blower Fan #2 Power
HDD 0 to Server Board SATA 2
HDD 1 to Server Board SATA 3
HDD 2 to Server Board SATA 4
Optical Drive to Server Board SATA 0
H
E
AF002486
Figure 82. Cable Routing (SR1530HSH)
90
Intel® Server System SR1530SH/SR1530HSH User’s Guide
350-W Single Power Supply Input Voltages
• 100 - 127 V at 50/60 Hz 6.0 A
• 200 - 240 V at 50/60 Hz 3.0 A
350-W Single Power Supply Output Voltages
Table 5 lists the total wattage available from the power subsystem for each voltage. For
information about calculating the power usage for your configuration, see “Calculating
Power Usage.”
Table 5. Power Supply Output Capability
Voltage
Maximum Current
+3.3 V
14 A
+5.0 V
18 A
+5 V Standby
2A
+12.0
24 A
-12.0 V
0.3 A
Warning: Do not exceed a combined power output of 90 W for the +5 V and +3.3 V outputs.
Exceeding a combined 90 W will overload the power subsystem and may cause the power
supplies to overheat and malfunction.
Intel® Server System SR1530SH/SR1530HSH User’s Guide
91
System Environmental Specifications
Table 6. System Environmental Specifications
Temperature
Non-operating
-40 ° to 70 ° C
Operating
10 ° to 35 °C, with the maximum rate of change not to exceed 10 ° C per
hour
Humidity
Non-operating
90% relative humidity, non-condensing at 35 °C
Shock
92
Operating
2.0 g, 11 msec, 1/2 sine
Packaged
Operational after an 24-inch free fall.
Acoustic noise
7 Bels in sound power for a typical office ambient temperature (65 to 75
°F). Your selection of peripherals may change the noise level.
Electrostatic
discharge (ESD)
Tested to 15 kilovolts (kV); no component damage.
Intel® Server System SR1530SH/SR1530HSH User’s Guide
Appendix B: Troubleshooting
This chapter helps you identify and solve problems that might occur while you are using
the system.
For any issue, first ensure you are using the latest firmware and files. Firmware upgrades
include updates for the BIOS, Baseboard Management Controller (BMC), and hot-swap
controller (HSC). See “Server System References” on page x for a link to the software
updates. In addition to the server firmware and files, also update any drivers used for
components you installed in your system, such as video drivers, network drivers, and
SATA drivers.
Intel provides a package called the “Platform Confidence Test” that may help with your
diagnostics. See “Server System References” on page x for a link to this software.
If you cannot resolve your server problems on your own, see “Getting Help” on page 155
for assistance.
Resetting the System
Before going through in-depth troubleshooting, attempt first to reset your system using
one of the methods below.
Table 7. Resetting the System
To do this
Press
Soft boot reset to clear the system memory and reload the operating
system
<Ctrl+Alt+Del>
Clear system memory, restart POST, and reload the operating system
Reset button
Cold boot reset. Turn the system power off and then on. This clears
system memory, restarts POST, reloads the operating system, and halts
power to all peripherals
Power off/on
button
Reset the BMC and get it back to a stable state
Remove AC
power from the
server for one
minute
Intel® Server System SR1530SH/SR1530HSH User’s Guide
93
Problems following Initial System Installation
Problems that occur at initial system startup are usually caused by an incorrect installation
or configuration. Hardware failure is a less frequent cause. If the problem you are
experiencing is with a specific software application, see “Problems with Newly Installed
Application Software” on page 100.
First Steps Checklist
• Is AC power available at the wall outlet?
• Are the power supplies plugged in? Check the AC cable(s) on the back of the chassis
and at the AC source.
• Are all cables correctly connected and secured?
• Are the processors fully seated in their sockets on the server board?
• Are all standoffs in the proper location and not touching any components, causing a
potential short?
• Are all add-in PCI boards fully seated in their slots on the server board?
• Are all jumper settings on the server board correct?
• Are all jumper and switch settings on add-in boards and peripheral devices correct?
To check these settings, refer to the manufacturer's documentation that comes with
them. If applicable, ensure there are no conflicts (for example, two add-in boards
sharing the same interrupt).
•
•
•
•
•
•
Are all peripheral devices installed correctly?
If the system has a hard disk drive, is it properly formatted or configured?
Are all device drivers properly installed?
Are the configuration settings made in Setup correct?
Is the operating system properly loaded? See the operating system documentation.
Did you press the system power on/off switch on the front panel to turn the server on
(power on light should be lit)?
• Is the system power cord properly connected to the system and plugged into a
NEMA 5 15R outlet for 100-120 V or a NEMA 6-15R outlet for 200-240 V?
• Are all integrated components from the tested components lists? Check the tested
memory and chassis lists, as well as the supported hardware and operating system
list. See “Server System References” on page x for links to the tested component
lists.
94
Intel® Server System SR1530SH/SR1530HSH User’s Guide
Hardware Diagnostic Testing
This section provides a more detailed approach to identifying a hardware problem and
locating its source.
Caution: Turn off devices before disconnecting cables: Before disconnecting any peripheral cables
from the system, turn off the system and any external peripheral devices. Failure to do so
can cause permanent damage to the system and/or the peripheral devices.
1. Turn off the system and all external peripheral devices. Except for the keyboard and
video monitor, disconnect each device from the system.
2. Make sure the system power cord is plugged into a properly grounded AC outlet.
3. Make sure your video display monitor and keyboard are correctly connected to the
system. Turn on the video monitor. Set its brightness and contrast controls to at
least two thirds of their maximum ranges (see the documentation supplied with
your video display monitor).
4. If the operating system normally loads from the hard disk drive, make sure there is
no CD-ROM/DVD disk in the optical drive.
5. If the power LED does light, attempt to boot from a USB floppy or from a CDROM disk.
6. Turn on the system. If the power LED does not light, see “Power Light Does Not
Light” on page 96.
Verifying Proper Operation of Key System Lights
As POST determines the system configuration, it tests for the presence of each mass
storage device installed in the system. As each device is checked, its activity light should
turn on briefly. Check for the following:
• Does the drive activity light turn on briefly? If not, see “Drive Activity Light Does
Not Light” on page 98.
Confirming Loading of the Operating System
Once the system boots up, the operating system prompt displays on the screen. The
prompt varies according to the operating system. If the operating system prompt does not
display, see “No Characters Appear on Screen” on page 96.
Specific Problems and Corrective Actions
This section provides possible solutions for these specific problems:
• Power light does not light.
• No characters appear on screen.
Intel® Server System SR1530SH/SR1530HSH User’s Guide
95
• Characters on the screen appear distorted or incorrect.
• System cooling fans do not rotate.
• Diskette drive activity light does not light.
• Hard disk drive activity light does not light.
• CD-ROM drive activity light does not light.
• There are problems with application software.
• The bootable CD-ROM is not detected.
Try the following solutions in the order given. If you cannot correct the problem, contact
your service representative or authorized dealer for help.
Power Light Does Not Light
Check the following:
• Did you press the power-on button?
• Is the system operating normally? If yes, the power LED might be defective or the
connection from the front panel to the server board might be loose.
• Have you securely plugged the server AC power cord into the power supply?
• Some ATX power supplies have a power switch on the back of the power supply. If
your system has one, is it turned on?
• Remove all add-in cards and see if the system boots. If successful, add the cards
back in one at a time with a reboot between each addition.
• Make sure the memory DIMMs comply with the system requirements.
• Make sure the memory DIMMs have been populated according to the system
requirements.
• Remove the memory DIMMs and re-seat them.
• Make sure the processor(s) comply with the system requirements.
• Make sure the processor(s) have been populated according to the system
requirements.
• Remove the processor(s) and re-seat them.
• Make sure the chassis standoffs are installed only below mounting holes. Misplaced
standoffs can contact the pins on the bottom of the server board and cause a short.
No Characters Appear on Screen
Check the following:
• Is the keyboard functioning? Test it by turning the “Num Lock” function on and off
to make sure the Num Lock light is functioning.
96
Intel® Server System SR1530SH/SR1530HSH User’s Guide
• Is the video monitor plugged in and turned on? If you are using a switch box, is it
switched to the correct system?
• Are the brightness and contrast controls on the video monitor properly adjusted?
•
•
•
•
Is the video monitor signal cable properly installed?
Does this video monitor work correctly if plugged into a different system?
Is the onboard video controller enabled in the BIOS?
Remove all add-in cards and see if the video returns. If successful, add the cards
back in one at a time with a reboot between each addition.
• Make sure the memory DIMMs comply with the system requirements.
• Make sure the memory DIMMs have been populated according to the system
requirements.
• Remove the memory DIMMs and re-seat them.
• Make sure the processor(s) comply with the system requirements.
• Make sure the processor(s) have been populated according to the system
requirements.
• Remove the processor(s) and re-seat them.
If you are using an add-in video controller board, do the following:
1. Verify the video works using the onboard video controller.
2. Verify the video controller board is fully seated in the server board connector.
3. Reboot the system for changes to take effect.
4. If there are still no characters on the screen after you reboot the system and POST
emits a beep code, write down the beep code you hear. This information is useful
for your service representative.
5. If you do not receive a beep code and characters do not display, the video display
monitor or video controller may have failed. Contact your service representative or
authorized dealer for help.
Characters Are Distorted or Incorrect
Check the following:
• Are the brightness and contrast controls properly adjusted on the video monitor? See
the manufacturer's documentation.
• Are the video monitor's signal and power cables properly installed?
• Does this video monitor work correctly if plugged into a different system?
System Cooling Fans Do Not Rotate Properly
If the system cooling fans are not operating properly, it is an indication of possible system
component failure.
Intel® Server System SR1530SH/SR1530HSH User’s Guide
97
Check the following:
• Is the power-on light lit? If not, see “Power Light Does Not Light” on page 96.
• Are any other front panel LEDs lit?
• Have any of the fan motors stopped? Use the server management subsystem to
check the fan status.
•
•
•
•
Have your fans speeded up in response to an overheating situation?
Have your fans speeded up in response to a fan that has failed?
Are the fan power connectors properly connected to the server board?
Is the cable from the front panel board connected to the both the front panel board
and to the server board?
• Are the power supply cables properly connected to the server board?
• Are there any shorted wires caused by pinched-cables or have power connector
plugs been forced into power connector sockets the wrong way?
Drive Activity Light Does Not Light
Check the following:
• Are the drive's power and signal cables properly installed?
• Are all relevant switches and jumpers on the drive set correctly?
• Is the drive properly configured?
• Is the drive activity light always on? If so, the signal cable may be plugged in
incorrectly.
CD-ROM Drive or DVD-ROM Drive Activity Light Does Not
Light
Check the following:
• Are the CD-ROM/DVD-ROM drive's power and signal cables properly installed?
• Are all relevant switches and jumpers on the drive set correctly?
• Is the drive properly configured?
Cannot Connect to a Server
• Make sure the network cable is securely attached to the correct connector at the
system back panel.
• Try a different network cable.
• Make sure you are using the correct and the current drivers. See “Server System
References” on page x for a link to the current drivers.
98
Intel® Server System SR1530SH/SR1530HSH User’s Guide
• Make sure the driver is loaded and the protocols are bound.
• Make sure the hub port is configured for the same duplex mode as the network
controller.
• Make sure the correct networking software is installed.
• If you are directly connecting two servers (without a hub), you will need a crossover
cable.
• Check the network controller LEDs next to the NIC connectors.
Problems with Network
The server hangs when the drivers are loaded
• Certain drivers may require interrupts that are not shared with other PCI drivers. For
these drivers, it may be necessary to alter settings so that interrupts are not shared.
See the documentation that came with your PCI card(s) for information on changing
interrupts.
Diagnostics pass but the connection fails
•
•
•
•
•
Make sure the network cable is securely attached.
Make sure you specify the correct frame type in your NET.CFG file.
The controller stopped working when an add-in adapter was installed.
Make sure the cable is connected to the port from the onboard network controller.
Make sure your BIOS is current. See “Server System References” on page x for a
link to the current version.
• Make sure the other adapter supports shared interrupts. Make sure your operating
system supports shared interrupts.
• Try reseating the add-in adapter.
The add-in adapter stopped working without apparent cause
• Reseat the adapter.
• The network driver files may be corrupt or deleted. Delete and then reinstall the
drivers.
• Run diagnostics.
Intel® Server System SR1530SH/SR1530HSH User’s Guide
99
System Boots when Installing PCI Card
System Management features require full-time “standby” power. This means some parts
of the system have power going to them whenever the power cord is plugged in, even if
you have turned the system power off with the power button on the front panel. If you
install a PCI card with the AC power cord plugged in, a signal may be sent to command
the system to boot. Before installing a PCI card, you should always:
• Turn off the server power by using the power button on the front of the system.
• Unplug the AC power cord(s) from the server.
Problems with Newly Installed Application Software
Problems that occur when you run new application software are usually related to the
software, not the server hardware. Faulty equipment is unlikely, especially if other
software runs correctly.
Check the following:
• Make sure the system meets the minimum hardware requirements for the software.
See the software documentation.
• Make sure the software is properly installed and configured for the system. See the
software documentation.
• Use only an authorized copy. Unauthorized copies often do not work.
• If you are running the software from a CD-ROM or DVD-ROM, try a different disk.
• Make sure the correct device drivers installed.
If the problems persist, contact the software vendor's customer service representative.
Problems with Application Software that Ran Correctly
Earlier
Problems that occur after the system hardware and software have been running correctly
sometimes indicate equipment failure. However, they can also be caused by file
corruption or changes to the software configuration.
Check the following:
•
•
•
•
If you are running the software from a CD-ROM or DVD-ROM, try a different disk.
Check your system for a virus infection.
Uninstall and reinstall the software. Make sure all necessary files are installed.
If the problems are intermittent, there may be a loose cable, dirt in the keyboard (if
keyboard input is incorrect), a marginal power supply, or other random component
failures.
• If you suspect a transient voltage spike, power outage, or brownout might have
occurred, reload the software and try running it again. Symptoms of voltage spikes
100
Intel® Server System SR1530SH/SR1530HSH User’s Guide
include a flickering video display, unexpected system reboots, and the system not
responding to user commands.
Note: Random errors in data files: If you are getting random errors in your data files, they may
be getting corrupted by voltage spikes on your power line. If you are experiencing any of
the above symptoms that might indicate voltage spikes on the power line, you may want to
install a surge suppressor between the power outlet and the system power cord.
Devices are not Recognized under Device Manager
(Microsoft Windows* Operating System)
The Microsoft Windows* operating systems do not include all of the drivers for the Intel®
chipsets, onboard NICs, and other components. See “Server System References” on
page x for a link to the current drivers and chipset files.
Hard Drive(s) are not Recognized
Check the following:
• Make sure the drive is not disabled in BIOS Setup.
• Make sure the drive is connected correctly and that is plugged into the power supply.
• Make sure the drive is compatible. See “Server System References” on page x for a
link to the tested drives.
• Make sure you have not exceeded the power budget for the server. See “Server
System References” on page x for a link to software to check your power budget.
• If using SCSI drives, verify that each SCSI ID number is unique on the SCSI bus.
See your drive documentation for details on setting the SCSI ID for your drives.
• If using ATA drives, verify that the master/slave settings are set correctly. See your
drive documentation for details on setting the master/slave settings.
• If using a RAID configuration with SCSI or SATA drives, make sure the RAID card
is installed correctly.
Bootable CD-ROM Disk Is Not Detected
Check the following:
• Make sure the BIOS is configured to allow the CD-ROM to be the first bootable
device.
Intel® Server System SR1530SH/SR1530HSH User’s Guide
101
LED Information
The Intel® Server System SR1530AH / SR1530AHLX / SR1530HAHLX includes LEDs
that can aid in troubleshooting your system. Table 8 lists these LEDs and provides a
description of their use.
Table 8. LED Information
LED Name
Power
Function
Location
Indicates system power
is on or off
Front front
panel
LED Color
Green
Notes
Off = Power is off or in sleep
state S5
On = Power is on or in sleep
state S0
BIOS POST Beep Codes
Table 9 lists the POST error beep codes. Prior to system video initialization, the BIOS
uses these beep codes to inform users of error conditions. Please note that not all error
conditions are supported by BIOS beep codes.
Table 9. POST Error Beep Codes
Number of
Beeps
102
Reason for Beeps and Action to Take
1, 2, or 3
Memory error. Reseat the memory or replace the DIMMs with known good
modules.
4 - 7 or 9 - 11
Fatal error indicating a possible serious system problem. Remove all addin cards and re-start the system. If the error still occurs, contact your
system manufacturer. If the beep codes are not generated after the add-in
cards are removed, insert the cards one at a time, booting the system
between each card addition, until the beeps again occur to reveal the
malfunctioning card.
8
Replace or reseat the system video add-in card. If on-board video is being
used, the server board may be faulty.
Intel® Server System SR1530SH/SR1530HSH User’s Guide
Appendix C: Installation/Assembly
Safety Instructions
English
The power supply in this product contains no user-serviceable
parts. Refer servicing only to qualified personnel.
Do not attempt to modify or use the supplied AC power cord if it is
not the exact type required. A product with more than one power
supply will have a separate AC power cord for each supply.
The power button on the system does not turn off system AC
power. To remove AC power from the system, you must unplug
each AC power cord from the wall outlet or power supply.
The power cord(s) is considered the disconnect device to the main
(AC) power. The socket outlet that the system plugs into shall be
installed near the equipment and shall be easily accessible.
SAFETY STEPS: Whenever you remove the chassis covers to
access the inside of the system, follow these steps:
1. Turn off all peripheral devices connected to the system.
2. Turn off the system by pressing the power button.
3. Unplug all AC power cords from the system or from wall
outlets.
4. Label and disconnect all cables connected to I/O connectors
or ports on the back of the system.
5. Provide some electrostatic discharge (ESD) protection by
wearing an antistatic wrist strap attached to chassis ground
of the system-any unpainted metal surface-when handling
components.
6. Do not operate the system with the chassis covers removed.
Intel® Server System SR1530SH/SR1530HSH User’s Guide
103
After you have completed the six SAFETY steps above, you can
remove the system covers. To do this:
1. Unlock and remove the padlock from the back of the system
if a padlock has been installed.
2. Remove and save all screws from the covers.
3. Remove the cover(s).
For proper cooling and airflow, always reinstall the chassis covers
before turning on the system. Operating the system without the
covers in place can damage system parts. To install the covers:
1. Check first to make sure you have not left loose tools or parts
inside the system.
2. Check that cables, add-in boards, and other components are
properly installed.
3. Attach the covers to the chassis with the screws removed
earlier, and tighten them firmly.
4. Insert and lock the padlock to the system to prevent
unauthorized access inside the system.
5. Connect all external cables and the AC power cord(s) to the
system.
A microprocessor and heat sink may be hot if the system has been
running. Also, there may be sharp pins and edges on some board
and chassis parts. Contact should be made with care. Consider
wearing protective gloves.
Danger of explosion if the battery is incorrectly replaced. Replace
only with the same or equivalent type recommended by the
equipment manufacturer. Dispose of used batteries according to
manufacturer's instructions.
The system is designed to operate in a typical office environment.
Choose a site that is:
• Clean and free of airborne particles (other than normal room
dust).
• Well ventilated and away from sources of heat including direct
sunlight.
• Away from sources of vibration or physical shock.
• Isolated from strong electromagnetic fields produced by
electrical devices.
• In regions that are susceptible to electrical storms, we
recommend you plug your system into a surge suppressor and
disconnect telecommunication lines to your modem during an
electrical storm.
• Provided with a properly grounded wall outlet.
• Provided with sufficient space to access the power supply
cord(s), because they serve as the product's main power
disconnect.
104
Intel® Server System SR1530SH/SR1530HSH User’s Guide
Deutsch
Benutzer können am Netzgerät dieses Produkts keine Reparaturen
vornehmen. Das Produkt enthält möglicherweise mehrere
Netzgeräte. Wartungsarbeiten müssen von qualifizierten
Technikern ausgeführt werden.
Versuchen Sie nicht, das mitgelieferte Netzkabel zu ändern oder zu
verwenden, wenn es sich nicht genau um den erforderlichen Typ
handelt. Ein Produkt mit mehreren Netzgeräten hat für jedes
Netzgerät ein eigenes Netzkabel.
Der Wechselstrom des Systems wird durch den Ein-/Aus-Schalter
für Gleichstrom nicht ausgeschaltet. Ziehen Sie jedes
Wechselstrom-Netzkabel aus der Steckdose bzw. dem Netzgerät,
um den Stromanschluß des Systems zu unterbrechen.
SICHERHEISMASSNAHMEN: Immer wenn Sie die
Gehäuseabdeckung abnehmen um an das Systeminnere zu
gelangen, sollten Sie folgende Schritte beachten:
1. Schalten Sie alle an Ihr System angeschlossenen
Peripheriegeräte aus.
2. Schalten Sie das System mit dem Hauptschalter aus.
3. Ziehen Sie den Stromanschlußstecker Ihres Systems aus
der Steckdose.
4. Auf der Rückseite des Systems beschriften und ziehen Sie
alle Anschlußkabel von den I/O Anschlüssen oder Ports ab.
5. Tragen Sie ein geerdetes Antistatik Gelenkband, um
elektrostatische Ladungen (ESD) über blanke Metallstellen
bei der Handhabung der Komponenten zu vermeiden.
6. Schalten Sie das System niemals ohne ordnungsgemäß
montiertes Gehäuse ein.
Intel® Server System SR1530SH/SR1530HSH User’s Guide
105
SICHERHEISMASSNAHMEN: Immer wenn Sie die
Gehäuseabdeckung abnehmen um an das Systeminnere zu
gelangen, sollten Sie folgende Schritte beachten:
1. Schalten Sie alle an Ihr System angeschlossenen
Peripheriegeräte aus.
2. Schalten Sie das System mit dem Hauptschalter aus.
3. Ziehen Sie den Stromanschlußstecker Ihres Systems aus
der Steckdose.
4. Auf der Rückseite des Systems beschriften und ziehen Sie
alle Anschlußkabel von den I/O Anschlüssen oder Ports ab.
5. Tragen Sie ein geerdetes Antistatik Gelenkband, um
elektrostatische Ladungen (ESD) über blanke Metallstellen
bei der Handhabung der Komponenten zu vermeiden.
6. Schalten Sie das System niemals ohne ordnungsgemäß
montiertes Gehäuse ein.
Zur ordnungsgemäßen Kühlung und Lüftung muß die
Gehäuseabdeckung immer wieder vor dem Einschalten installiert
werden. Ein Betrieb des Systems ohne angebrachte Abdeckung
kann Ihrem System oder Teile darin beschädigen. Um die
Abdeckung wieder anzubringen:
1. Vergewissern Sie sich, daß Sie keine Werkzeuge oder Teile
im Innern des Systems zurückgelassen haben.
2. Überprüfen Sie alle Kabel, Zusatzkarten und andere
Komponenten auf ordnungsgemäßen Sitz und Installation.
3. Bringen Sie die Abdeckungen wieder am Gehäuse an, indem
Sie die zuvor gelösten Schrauben wieder anbringen. Ziehen
Sie diese gut an.
4. Bringen Sie die Verschlußeinrichtung (Padlock) wieder an
und schließen Sie diese, um ein unerlaubtes Öffnen des
Systems zu verhindern.
5. Schließen Sie alle externen Kabel und den AC
Stromanschlußstecker Ihres Systems wieder an.
Der Mikroprozessor und der Kühler sind möglicherweise erhitzt,
wenn das System in Betrieb ist. Außerdem können einige Platinen
und Gehäuseteile scharfe Spitzen und Kanten aufweisen. Arbeiten
an Platinen und Gehäuse sollten vorsichtig ausgeführt werden. Sie
sollten Schutzhandschuhe tragen.
Bei falschem Einsetzen einer neuen Batterie besteht
Explosionsgefahr. Die Batterie darf nur durch denselben oder einen
entsprechenden, vom Hersteller empfohlenen Batterietyp ersetzt
werden. Entsorgen Sie verbrauchte Batterien den Anweisungen
des Herstellers entsprechend.
106
Intel® Server System SR1530SH/SR1530HSH User’s Guide
Das System wurde für den Betrieb in einer normalen
Büroumgebung entwickelt. Der Standort sollte:
• "sauber und staubfrei sein (Hausstaub ausgenommen);
• "gut gelüftet und keinen Heizquellen ausgesetzt sein
(einschließlich direkter Sonneneinstrahlung);
• "keinen Erschütterungen ausgesetzt sein;
• "keine starken, von elektrischen Geräten erzeugten
elektromagnetischen Felder aufweisen;
• "in Regionen, in denen elektrische Stürme auftreten, mit einem
Überspannungsschutzgerät verbunden sein; während eines
elektrischen Sturms sollte keine Verbindung der
Telekommunikationsleitungen mit dem Modem bestehen;
• "mit einer geerdeten Wechselstromsteckdose ausgerüstet
sein;
• "über ausreichend Platz verfügen, um Zugang zu den
Netzkabeln zu gewährleisten, da der Stromanschluß des
Produkts hauptsächlich über die Kabel unterbrochen wird
Français
Le bloc d'alimentation de ce produit ne contient aucune pièce
pouvant être réparée par l'utilisateur. Ce produit peut contenir plus
d'un bloc d'alimentation. Veuillez contacter un technicien qualifié en
cas de problème.
Ne pas essayer d'utiliser ni modifier le câble d'alimentation CA
fourni, s'il ne correspond pas exactement au type requis. Le
nombre de câbles d'alimentation CA fournis correspond au nombre
de blocs d'alimentation du produit
Notez que le commutateur CC de mise sous tension /hors tension
du panneau avant n'éteint pas l'alimentation CA du système. Pour
mettre le système hors tension, vous devez débrancher chaque
câble d'alimentation de sa prise.
Intel® Server System SR1530SH/SR1530HSH User’s Guide
107
CONSIGNES DE SÉCURITÉ -Lorsque vous ouvrez le boîtier pour
accéder à l'intérieur du système, suivez les consignes suivantes:
1. Mettez hors tension tous les périphériques connectés au
système.
2. Mettez le système hors tension en mettant l'interrupteur
général en position OFF (bouton-poussoir).
3. Débranchez tous les cordons d'alimentation c.a. du système
et des prises murales.
4. Identifiez et débranchez tous les câbles reliés aux
connecteurs d'E-S ou aux accès derrière le système.
5. Pour prévenir les décharges électrostatiques lorsque vous
touchez aux composants, portez une bande antistatique pour
poignet et reliez-la à la masse du système (toute surface
métallique non peinte du boîtier).
6. Ne faites pas fonctionner le système tandis que le boîtier est
ouvert.
Une fois TOUTES les étapes précédentes accomplies, vous
pouvez retirer les panneaux du système. Procédez comme suit:
1. Si un cadenas a été installé sur à l'arrière du système,
déverrouillez-le et retirez-le.
2. Retirez toutes les vis des panneaux et mettez-les dans un
endroit sûr.
3. Retirez les panneaux.
Afin de permettre le refroidissement et l'aération du système,
réinstallez toujours les panneaux du boîtier avant de mettre le
système sous tension. Le fonctionnement du système en l'absence
des panneaux risque d'endommager ses pièces. Pour installer les
panneaux, procédez comme suit:
1. Assurez-vous de ne pas avoir oublié d'outils ou de pièces
démontées dans le système.
2. Assurez-vous que les câbles, les cartes d'extension et les
autres composants sont bien installés.
3. Revissez solidement les panneaux du boîtier avec les vis
retirées plus tôt.
4. Remettez le cadenas en place et verrouillez-le afin de
prévenir tout accès non autorisé à l'intérieur du système.
5. Rebranchez tous les cordons d'alimentation c. a. et câbles
externes au système.
Le microprocesseur et le dissipateur de chaleur peuvent être
chauds si le système a été sous tension. Faites également attention
aux broches aiguës des cartes et aux bords tranchants du capot.
Nous vous recommandons l'usage de gants de protection.
108
Intel® Server System SR1530SH/SR1530HSH User’s Guide
Danger d'explosion si la batterie n'est pas remontée correctement.
Remplacer uniquement avec une batterie du même type ou d'un
type équivalent recommandé par le fabricant. Disposez des piles
usées selon les instructions du fabricant.
Le système a été conçu pour fonctionner dans un cadre de travail
normal. L'emplacement choisi doit être:
• "Propre et dépourvu de poussière en suspension (sauf la
poussière normale).
• "Bien aéré et loin des sources de chaleur, y compris du soleil
direct.
• "A l'abri des chocs et des sources de vibrations.
• "Isolé de forts champs électromagnétiques géenérés par des
appareils électriques.
• "Dans les régions sujettes aux orages magnétiques il est
recomandé de brancher votre système à un supresseur de
surtension, et de débrancher toutes les lignes de
télécommunications de votre modem durant un orage.
• "Muni d'une prise murale correctement mise à la terre.
• "Suffisamment spacieux pour vous permettre d'accéder aux
câbles d'alimentation (ceux-ci étant le seul moyen de mettre le
système hors tension).
Español
El usuario debe abstenerse de manipular los componentes de la
fuente de alimentación de este producto, cuya reparación debe
dejarse exclusivamente en manos de personal técnico
especializado. Puede que este producto disponga de más de una
fuente de alimentación
No intente modificar ni usar el cable de alimentación de corriente
alterna, si no corresponde exactamente con el tipo requerido.
El número de cables suministrados se corresponden con el número
de fuentes de alimentación de corriente alterna que tenga el
producto
Intel® Server System SR1530SH/SR1530HSH User’s Guide
109
Nótese que el interruptor activado/desactivado en el panel frontal
no desconecta la corriente alterna del sistema. Para desconectarla,
deberá desenchufar todos los cables de corriente alterna de la
pared o desconectar la fuente de alimentación.
INSTRUCCIONES DE SEGURIDAD: Cuando extraiga la tapa del
chasis para acceder al interior del sistema, siga las siguientes
instrucciones:
1. Apague todos los dispositivos periféricos conectados al
sistema.
2. Apague el sistema presionando el interruptor encendido/
apagado.
3. Desconecte todos los cables de alimentación CA del sistema
o de las tomas de corriente alterna.
4. Identifique y desconecte todos los cables enchufados a los
conectores E/S o a los puertos situados en la parte posterior
del sistema.
5. Cuando manipule los componentes, es importante
protegerse contra la descarga electrostática (ESD). Puede
hacerlo si utiliza una muñequera antiestática sujetada a la
toma de tierra del chasis - o a cualquier tipo de superficie de
metal sin pintar.
6. No ponga en marcha el sistema si se han extraído las tapas
del chasis.
Después de completar las seis instrucciones de SEGURIDAD
mencionadas, ya puede extraer las tapas del sistema. Para ello:
1. Desbloquee y extraiga el bloqueo de seguridad de la parte
posterior del sistema, si se ha instalado uno.
2. Extraiga y guarde todos los tornillos de las tapas.Extraiga las
tapas.
Para obtener un enfriamiento y un flujo de aire adecuados,
reinstale siempre las tapas del chasis antes de poner en marcha el
sistema. Si pone en funcionamiento el sistema sin las tapas bien
colocadas puede dañar los componentes del sistema. Para instalar
las tapas:
1. Asegúrese primero de no haber dejado herramientas o
componentes sueltos dentro del sistema.
2. Compruebe que los cables, las placas adicionales y otros
componentes se hayan instalado correctamente.
3. Incorpore las tapas al chasis mediante los tornillos extraídos
anteriormente, tensándolos firmemente.
4. Inserte el bloqueo de seguridad en el sistema y bloquéelo
para impedir que pueda accederse al mismo sin
autorización.
5. Conecte todos los cables externos y los cables de
alimentación CA al sistema.
110
Intel® Server System SR1530SH/SR1530HSH User’s Guide
Si el sistema ha estado en funcionamiento, el microprocesador y el
disipador de calor pueden estar aún calientes. También conviene
tener en cuenta que en el chasis o en el tablero puede haber
piezas cortantes o punzantes. Por ello, se recomienda precaución y
el uso de guantes protectores.
Existe peligro de explosión si la pila no se cambia de forma
adecuada. Utilice solamente pilas iguales o del mismo tipo que las
recomendadas por el fabricante del equipo. Para deshacerse de las
pilas usadas, siga igualmente las instrucciones del fabricante.
El sistema está diseñado para funcionar en un entorno de trabajo
normal. Escoja un lugar:
• "Limpio y libre de partículas en suspensión (salvo el polvo
normal).
• "Bien ventilado y alejado de fuentes de calor, incluida la luz
solar directa.
• "Alejado de fuentes de vibración.
• "Aislado de campos electromagnéticos fuertes producidos por
dispositivos eléctricos.
• "En regiones con frecuentes tormentas eléctricas, se
recomienda conectar su sistema a un eliminador de
sobrevoltage y desconectar el módem de las líneas de
telecomunicación durante las tormentas.
• "Provisto de una toma de tierra correctamente instalada.
• "Provisto de espacio suficiente como para acceder a los cables
de alimentación, ya que éstos hacen de medio principal de
desconexión del sistema.
Intel® Server System SR1530SH/SR1530HSH User’s Guide
111
Italiano
Rivolgersi ad un tecnico specializzato per la riparazione dei
componenti dell'alimentazione di questo prodotto. È possibile che il
prodotto disponga di più fonti di alimentazione.
Non modificare o utilizzare il cavo di alimentazione in c.a. fornito dal
produttore, se non corrisponde esattamente al tipo richiesto. Ad
ogni fonte di alimentazione corrisponde un cavo di alimentazione in
c.a. separato
L'interruttore attivato/disattivato nel pannello anteriore non
interrompe l'alimentazione in c.a. del sistema. Per interromperla, è
necessario scollegare tutti i cavi di alimentazione in c.a. dalle prese
a muro o dall'alimentazione di corrente.
PASSI DI SICUREZZA: Qualora si rimuovano le coperture del
telaio per accedere all'interno del sistema, seguire i seguenti passi:
1. Spegnere tutti i dispositivi periferici collegati al sistema.
2. Spegnere il sistema, usando il pulsante spento/acceso
dell'interruttore del sistema.
3. Togliere tutte le spine dei cavi del sistema dalle prese
elettriche.
4. Identificare e sconnettere tutti i cavi attaccati ai collegamenti
I/O od alle prese installate sul retro del sistema.
5. Qualora si tocchino i componenti, proteggersi dallo scarico
elettrostatico (SES), portando un cinghia anti-statica da
polso che è attaccata alla presa a terra del telaio del sistema
- qualsiasi superficie non dipinta - .
6. Non far operare il sistema quando il telaio è senza le
coperture.
Dopo aver seguito i sei passi di SICUREZZA sopracitati, togliere le
coperture del telaio del sistema come seque:
1. Aprire e rimuovere il lucchetto dal retro del sistema qualora
ve ne fosse uno installato.
2. Togliere e mettere in un posto sicuro tutte le viti delle
coperture.
3. Togliere le coperture.
112
Intel® Server System SR1530SH/SR1530HSH User’s Guide
Per il giusto flusso dell'aria e raffreddamento del sistema, rimettere
sempre le coperture del telaio prima di riaccendere il sistema.
Operare il sistema senza le coperture al loro proprio posto
potrebbe danneggiare i componenti del sistema. Per rimettere le
coperture del telaio:
1. Controllare prima che non si siano lasciati degli attrezzi o dei
componenti dentro il sistema.
2. Controllare che i cavi, dei supporti aggiuntivi ed altri
componenti siano stati installati appropriatamente.
3. Attaccare le coperture al telaio con le viti tolte in precedenza
e avvitarle strettamente.
4. Inserire e chiudere a chiave il lucchetto sul retro del sistema
per impedire l'accesso non autorizzato al sistema.
5. Ricollegare tutti i cavi esterni e le prolunghe AC del sistema.
Se il sistema è stato a lungo in funzione, il microprocessore e il
dissipatore di calore potrebbero essere surriscaldati. Fare
attenzione alla presenza di piedini appuntiti e parti taglienti sulle
schede e sul telaio. È consigliabile l'uso di guanti di protezione.
Esiste il pericolo di un esplosione se la pila non viene sostituita in
modo corretto. Utilizzare solo pile uguali o di tipo equivalente a
quelle consigliate dal produttore. Per disfarsi delle pile usate,
seguire le istruzioni del produttore.
Il sistema è progettato per funzionare in un ambiente di lavoro tipo.
Scegliere una postazione che sia:
• "Pulita e libera da particelle in sospensione (a parte la normale
polvere presente nell'ambiente).
• "Ben ventilata e lontana da fonti di calore, compresa la luce
solare diretta.
• "Al riparo da urti e lontana da fonti di vibrazione.
• "Isolata dai forti campi magnetici prodotti da dispositivi elettrici.
• "In aree soggette a temporali, è consigliabile collegare il
sistema ad un limitatore di corrente. In caso di temporali,
scollegare le linee di comunicazione dal modem.
• "Dotata di una presa a muro correttamente installata.
• "Dotata di spazio sufficiente ad accedere ai cavi di
alimentazione, i quali rappresentano il mezzo principale di
scollegamento del sistema.
Intel® Server System SR1530SH/SR1530HSH User’s Guide
113
114
Intel® Server System SR1530SH/SR1530HSH User’s Guide
Appendix D: Safety Information
English
Server Safety Information
This document applies to Intel® server boards, Intel® server chassis (pedestal and rackmount), and installed peripherals. To reduce the risk of bodily injury, electrical shock, fire,
and equipment damage, read this document and observe all warnings and precautions in
this guide before installing or maintaining your Intel® server product.
In the event of a conflict between the information in this document and information
provided with the product or on the website for a particular product, the product
documentation takes precedence.
Your server should be integrated and serviced only by technically qualified persons.
You must adhere to the guidelines in this guide and the assembly instructions in your
server manuals to ensure and maintain compliance with existing product certifications and
approvals. Use only the described, regulated components specified in this guide. Use of
other products/components will void the UL Listing and other regulatory approvals of the
product, and may result in noncompliance with product regulations in the region(s) in
which the product is sold.
Safety Warnings and Cautions
To avoid personal injury or property damage, before you begin installing the product,
read, observe, and adhere to all of the following safety instructions and information. The
following safety symbols may be used throughout the documentation and may be marked
on the product and/or the product packaging.
CAUTION
Indicates the presence of a hazard that may cause minor personal injury or
property damage if the CAUTION is ignored.
WARNING
Indicates the presence of a hazard that may result in serious personal injury
if the WARNING is ignored.
Indicates potential hazard if indicated information is ignored.
Indicates shock hazards that result in serious injury or death if safety
instructions are not followed.
Indicates hot components or surfaces.
Intel® Server System SR1530SH/SR1530HSH User’s Guide
115
Indicates do not touch fan blades, may result in injury.
Indicates to unplug all AC power cord(s) to disconnect AC power
Please recycle battery
Intended Application Uses
This product was evaluated as Information Technology Equipment (ITE), which may be
installed in offices, schools, computer rooms, and similar commercial type locations. The
suitability of this product for other product categories and environments (such as medical,
industrial, residential, alarm systems, and test equipment), other than an ITE application,
may require further evaluation.
Site Selection
The system is designed to operate in a typical office environment. Choose a site that is:
• Clean, dry, and free of airborne particles (other than normal room dust).
• Well-ventilated and away from sources of heat including direct sunlight and
radiators.
• Away from sources of vibration or physical shock.
• Isolated from strong electromagnetic fields produced by electrical devices.
• In regions that are susceptible to electrical storms, we recommend you plug your
system into a surge suppresser and disconnect telecommunication lines to your
modem during an electrical storm.
• Provided with a properly grounded wall outlet.
• Provided with sufficient space to access the power supply cord(s), because they
serve as the product's main power disconnect.
Equipment Handling Practices
Reduce the risk of personal injury or equipment damage:
• Conform to local occupational health and safety requirements when moving and
lifting equipment.
• Use mechanical assistance or other suitable assistance when moving and lifting
equipment.
• To reduce the weight for easier handling, remove any easily detachable components.
116
Intel® Server System SR1530SH/SR1530HSH User’s Guide
Power and Electrical Warnings
Caution: The power button, indicated by the stand-by power marking, DOES NOT completely turn
off the system AC power, 5 V standby power is active whenever the system is plugged in.
To remove power from system, you must unplug the AC power cord from the wall outlet.
Your system may use more than one AC power cord. Make sure all AC power cords are
unplugged. Make sure the AC power cord(s) is/are unplugged before you open the chassis,
or add or remove any non hot-plug components.
Do not attempt to modify or use an AC power cord if it is not the exact type required. A
separate AC cord is required for each system power supply.
Some power supplies in Intel® servers use Neutral Pole Fusing. To avoid risk of shock use
caution when working with power supplies that use Neutral Pole Fusing.
The power supply in this product contains no user-serviceable parts. Do not open the
power supply. Hazardous voltage, current and energy levels are present inside the power
supply. Return to manufacturer for servicing.
When replacing a hot-plug power supply, unplug the power cord to the power supply
being replaced before removing it from the server.
To avoid risk of electric shock, turn off the server and disconnect the power cord,
telecommunications systems, networks, and modems attached to the server before opening
it.
Power Cord Warnings
If an AC power cord was not provided with your product, purchase one that is approved
for use in your country.
Caution: To avoid electrical shock or fire, check the power cord(s) that will be used with the
product as follows:
• Do not attempt to modify or use the AC power cord(s) if they are not the exact type
required to fit into the grounded electrical outlets
• The power cord(s) must meet the following criteria:
— The power cord must have an electrical rating that is greater than that of the
electrical current rating marked on the product.
— The power cord must have safety ground pin or contact that is suitable for the
electrical outlet.
— The power supply cord(s) is/are the main disconnect device to AC power. The
socket outlet(s) must be near the equipment and readily accessible for
disconnection.
— The power supply cord(s) must be plugged into socket-outlet(s) that is /are
provided with a suitable earth ground.
Intel® Server System SR1530SH/SR1530HSH User’s Guide
117
System Access Warnings
Caution: To avoid personal injury or property damage, the following safety instructions apply
whenever accessing the inside of the product:
• Turn off all peripheral devices connected to this product.
• Turn off the system by pressing the power button to off.
• Disconnect the AC power by unplugging all AC power cords from the system or wall
outlet.
• Disconnect all cables and telecommunication lines that are connected to the system.
• Retain all screws or other fasteners when removing access cover(s). Upon
completion of accessing inside the product, refasten access cover with original
screws or fasteners.
• Do not access the inside of the power supply. There are no serviceable parts in the
power supply. Return to manufacturer for servicing.
• Power down the server and disconnect all power cords before adding or replacing
any non hot-plug component.
• When replacing a hot-plug power supply, unplug the power cord to the power supply
being replaced before removing the power supply from the server.
Caution: If the server has been running, any installed processor(s) and heat sink(s) may be hot.
Unless you are adding or removing a hot-plug component, allow the system to cool before
opening the covers. To avoid the possibility of coming into contact with hot component(s)
during a hot-plug installation, be careful when removing or installing the hot-plug
component(s).
Caution: To avoid injury do not contact moving fan blades. If your system is supplied with a guard
over the fan, do not operate the system without the fan guard in place.
Rack Mount Warnings
The equipment rack must be anchored to an unmovable support to prevent it from tipping
when a server or piece of equipment is extended from it. The equipment rack must be
installed according to the rack manufacturer's instructions.
Install equipment in the rack from the bottom up, with the heaviest equipment at the
bottom of the rack.
Extend only one piece of equipment from the rack at a time.
You are responsible for installing a main power disconnect for the entire rack unit. This
main disconnect must be readily accessible, and it must be labeled as controlling power to
the entire unit, not just to the server(s).
To avoid risk of potential electric shock, a proper safety ground must be implemented for
the rack and each piece of equipment installed in it.
118
Intel® Server System SR1530SH/SR1530HSH User’s Guide
Electrostatic Discharge (ESD)
Caution: ESD can damage disk drives, boards, and other parts. We recommend that you perform all
procedures at an ESD workstation. If one is not available, provide some ESD protection
by wearing an antistatic wrist strap attached to chassis ground -- any unpainted metal
surface -- on your server when handling parts.
Always handle boards carefully. They can be extremely sensitive to ESD. Hold boards only
by their edges. After removing a board from its protective wrapper or from the server,
place the board component side up on a grounded, static free surface. Use a conductive
foam pad if available but not the board wrapper. Do not slide board over any surface.
Other Hazards
Battery Replacement
Caution: There is the danger of explosion if the battery is incorrectly replaced. When replacing the
battery, use only the battery recommended by the equipment manufacturer.
Dispose of batteries according to local ordinances and regulations.
Do not attempt to recharge a battery.
Do not attempt to disassemble, puncture, or otherwise damage a battery.
Cooling and Airflow
Caution: Carefully route cables as directed to minimize airflow blockage and cooling problems.
For proper cooling and airflow, operate the system only with the chassis covers installed.
Operating the system without the covers in place can damage system parts. To install the
covers:
• Check first to make sure you have not left loose tools or parts inside the system.
• Check that cables, add-in boards, and other components are properly installed.
• Attach the covers to the chassis according to the product instructions.
Laser Peripherals or Devices
Caution: To avoid risk of radiation exposure and/or personal injury:
• Do not open the enclosure of any laser peripheral or device.
• Laser peripherals or devices have are not user serviceable.
• Return to manufacturer for servicing.
Intel® Server System SR1530SH/SR1530HSH User’s Guide
119
Deutsch
Sicherheitshinweise für den Server
Das vorliegende Dokument bezieht sich auf Intel® Serverplatinen, Intel® Servergehäuse
(Standfuß und Rack) sowie installierte Peripheriegeräte. Es enthält Warnungen und
Vorsichtsmaßnahmen zur Vermeidung von Gefahren durch Verletzung, Stromschlag,
Feuer und Beschädigungen von Geräten. Lesen Sie diese Dokument daher sorgfältig,
bevor Sie Ihr Intel® Serverprodukt installieren oder warten.
Bei Widersprüchen zwischen den hier vorliegenden Angaben und den Informationen im
Lieferumfang des Produkts oder auf der Website des betreffenden Produkts hat die
Produktdokumentation Vorrang.
Die Integration und Wartung des Servers darf nur durch technisch qualifizierte Personen
erfolgen.
Um die Einhaltung der vorhandenen Zulassungen und Genehmigungen für das Produkt zu
gewährleisten, sind die Richtlinien in diesem Handbuch sowie die Montageanleitungen in
den Serverhandbüchern zu beachten. Verwenden Sie nur die beschriebenen, zugelassenen
Komponenten, die im vorliegenden Handbuch angegeben werden. Die Verwendung
anderer Produkte oder Komponenten führt zum Erlöschen der UL-Zulassung und anderer
Genehmigungen für das Produkt. Dadurch kann das Produkt gegen Produktbestimmungen
verstoßen, die im Verkaufsland gelten.
Sicherheitshinweise und Vorsichtsmaßnahmen
Um Verletzungen und Beschädigungen zu vermeiden, sollten Sie vor dem Beginn der
Produktinstallation die nachfolgend aufgeführten Sicherheitshinweise und -informationen
sorgfältig lesen und befolgen. In dem vorliegenden Handbuch sowie auf dem Produkt und
auf der Verpackung werden folgende Sicherheitssymbole verwendet:
VORSICHT
Weist auf eine Gefahrenquelle hin, die bei Nichtbeachtung des
VORSICHTSHINWEISES zu leichteren Verletzungen bzw.
Sachbeschädigungen führen kann.
WARNUNG
Weist auf eine Gefahrenquelle hin, die bei Nichtbeachtung der WARNUNG
zu ernsten Verletzungen führen kann.
Weist auf potentielle Gefahr bei Nichtbeachtung der angezeigten
Informationen hin.
Weist auf die Gefahr eines Stromschlags hin, der bei Nichtbeachtung der
Sicherheitshinweise zu schweren oder tödlichen Verletzungen führen kann.
Weist auf Verbrennungsgefahr an heißen Bauteilen bzw. Oberflächen hin.
120
Intel® Server System SR1530SH/SR1530HSH User’s Guide
Weist darauf hin, daß das Anfassen des Gebläses zu Verletzungen führen
kann.
Bedeutet, alle Netzkabel abzuziehen und das Gerät von der Netzspannung
zu trennen.
Bereiten Sie bitte Batterie auf
Zielbenutzer der Anwendung
Dieses Produkt wurde in seiner Eigenschaft als IT-Gerät getestet, das in Büros, Schulen,
Computerräumen und ähnlichen öffentlichen Räumlichkeiten installiert werden kann. Die
Eignung dieses Produkts für andere Einsatzbereiche als IT (z. B. Medizin, Industrie,
Alarmsysteme oder Prüfgeräte) kann u. U. weitere Tests erfordern.
Standortauswahl
Das System ist für den Betrieb innerhalb normaler Büroumgebungen geeignet. Wählen
Sie einen Standort, der folgenden Kriterien entspricht:
• Sauber, trocken und frei von Partikeln in der Luft (außer dem normalen Raumstaub).
• Gut belüftet, nicht in der Nähe von Wärmequellen und keiner direkten
Sonnenbestrahlung ausgesetzt.
• Nicht in der Nähe von Vibrations- oder Erschütterungsquellen.
• Abgeschirmt von starken elektromagnetischen Feldern, die durch elektrische Geräte
erzeugt werden.
• In gewittergefährdeten Gebieten sollten Sie das System an einen
Überspannungsschutz anschließen und bei einem Gewitter die
Telekommunikationskabel zum Modem abziehen.
• Eine ordnungsgemäß geerdete Wandsteckdose muß vorhanden sein.
• Ausreichender Freiraum für den Zugang zu den Netzkabeln, da diese die
Hauptvorrichtung zum Trennen des Produkts von der Stromversorgung sind.
Handhabung von Geräten
Beachten Sie zur Vermeidung von Verletzungen oder Beschädigungen an den Geräten die
folgenden Hinweise:
• Halten Sie beim Transportieren und Anheben von Geräten die örtlichen
Gesundheits- und Sicherheitsvorschriften ein.
• Verwenden Sie mechanische oder andere geeignete Hilfsmittel zum Transportieren
oder Anheben von Geräten.
• Entfernen Sie alle Komponenten, die sich leicht abnehmen lassen, um das Gewicht
zu reduzieren und die Handhabung zu erleichtern.
Intel® Server System SR1530SH/SR1530HSH User’s Guide
121
Warnungen zu Netzspannung und Elektrizität
Caution: Durch Betätigen der mit dem Standby-Symbol gekennzeichneten Netztaste wird das
System NICHT vollständig vom Netz getrennt. Es sind weiterhin 5 V aktiv, solange das
System eingesteckt ist. Um das System vollständig vom Strom zu trennen, muß das
Netzkabel aus der Steckdose abgezogen werden. Das System verfügt möglicherweise über
mehrere Netzkabel. Vergewissern Sie sich in diesem Fall, daß alle Netzkabel abgezogen
sind. Wenn Sie Komponenten ein- oder ausbauen möchten, die nicht hot-plug-fähig sind,
stellen Sie sicher, daß zuvor alle Netzkabel abgezogen sind.
Nehmen Sie keine Änderungen am Netzkabel vor, und verwenden Sie kein Kabel, das nicht
genau dem geforderten Typ entspricht. Jedes Netzteil im System muß über ein eigenes
Netzkabel angeschlossen werden.
Einige Netzteile von Intel Servern verwenden Nullleitersicherungen. Vorsicht ist geboten
im Umgang mit Netzteilen, welche Nullleitersicherungen verwenden, um das Risiko eines
elektrischen Schlages zu vermeiden
Das Netzteil in diesem Produkt enthält keine Teile, die vom Benutzer gewartet werden
können. Öffnen Sie das Netzteil nicht. Im Netzteil bestehen gefährliche Spannungen,
Ströme und Energiequellen. Schicken Sie das Gerät für Wartungsarbeiten an den
Hersteller zurück.
Wenn Sie ein hot-plug-fähiges Netzteil austauschen, ziehen Sie dessen Netzkabel ab, bevor
Sie es aus dem Server ausbauen.
Zur Vermeidung von Stromschlägen schalten Sie den Server aus, und trennen Sie vor dem
Öffnen des Geräts das Netzkabel sowie alle an den Server angeschlossene
Telekommunikationssysteme, Netzwerke und Modems.
Hinweis für Netzkabel
Wenn kein Netzkabel mit dem Produkt geliefert wurde, kaufen Sie ein Kabel, das für die
Caution: Prüfen Sie zur Vermeidung von Stromschlag oder Feuergefahr die mit dem Produkt zu
verwendenden Netzkabel wie folgt:
• Nehmen Sie keine Änderungen an einem Netzkabel vor, und benutzen sie es nicht,
wenn es nicht genau in die geerdeten Netzsteckdosen paßt.
• Netzkabel müssen die folgenden Anforderungen erfüllen:
—
Die Nennbelastbarkeit des Netzkabels muß mindestens so hoch sein wie die am
Produkt angegebenen Nennstromaufnahme.
—
Das Netzkabel muß einen zur Netzsteckdose passenden Schutzkontakt besitzen.
• Die Netzkabel sind die Hauptvorrichtung zum Trennen des Geräts vom Stromnetz.
Die Steckdose muß in der Nähe der Anlage angebracht und gut erreichbar sein.
• Netzkabel müssen an eine ordnungsgemäß geerdete Steckdose angeschlossen sein.
122
Intel® Server System SR1530SH/SR1530HSH User’s Guide
Warnhinweise für den Systemzugang
Caution: Um Verletzungen und Beschädigungen zu vermeiden, sollten Sie vor Arbeiten im
Produktinneren folgende Sicherheitsanweisungen beachten:
• Schalten Sie alle am Produkt angeschlossenen Peripheriegeräte aus.
• Schalten Sie das System mit dem Netzschalter aus.
• Trennen Sie das Gerät von der Stromquelle, indem Sie alle Netzkabel vom System
bzw. aus der Steckdose ziehen.
• Ziehen Sie alle Kabel und alle an das System angeschlossenen
Telekommunikationsleitungen ab.
• Bewahren Sie alle Schrauben und anderen Befestigungselemente gut auf, nachdem
Sie die Gehäuseabdeckung entfernt haben. Wenn Sie Ihre Arbeiten im Systeminneren
beendet haben, befestigen Sie die Gehäuseabdeckung mit den Originalschrauben
bzw. -befestigungselementen.
• Führen Sie keine Arbeiten im Netzteil aus. Das Netzteil enthält keine für den
Benutzer wartungsbedürftigen Teile. Schicken Sie das Gerät für Wartungsarbeiten
an den Hersteller zurück.
• Schalten Sie den Server aus, und ziehen Sie alle Netzkabel ab, bevor Sie
Komponenten ein- oder ausbauen, die nicht hot-plug-fähig sind.
• Wenn Sie ein hot-plug-fähiges Netzteil austauschen, ziehen Sie dessen Netzkabel ab,
bevor Sie es aus dem Server ausbauen.
Caution: War Ihr Server in Betrieb, können die installierten Prozessoren und Kühlkörper heiß sein.
Sofern Sie keine Hot-Plug-Komponenten ein- oder ausbauen, warten Sie mit dem
Abnehmen der Abdeckungen, bis das System abgekühlt ist. Gehen Sie beim Aus- oder
Einbauen von Hot-Plug-Komponenten sorgfältig vor, um nicht mit heißen Komponenten
in Berührung zu kommen.
Caution: Berühren Sie nicht die rotierenden Lüfterflügel, um Verletzungen zu vermeiden. Falls Ihr
System mit eine Lüfterabdeckung besitzt, darf es nicht ohne diese Abdeckung betrieben
werden.
Warnhinweise für Racks
Das Geräte-Rack muß auf einer geeigneten, festen Unterlage verankert werden, um ein
Umkippen zu vermeiden, wenn ein Server oder andere Geräte herausgezogen werden.
Bei der Installation des Racks müssen die Anweisungen des Rack-Herstellers beachtet
werden.
Gehen Sie bei der Installation von Geräten im Rack immer von unten nach oben vor, und
bauen Sie das schwerste Gerät an der untersten Position im Rack ein.
Ziehen Sie jeweils immer nur ein Gerät aus dem Rack heraus.
Intel® Server System SR1530SH/SR1530HSH User’s Guide
123
Sie müssen für die gesamte Rack-Einheit einen Netztrennschalter einrichten. Dieser
Netztrennschalter muß leicht zugänglich sein und über eine Kennzeichnung verfügen, die
besagt, daß er die Stromzufuhr zur gesamten Einheit steuert und nicht nur zu den Servern.
Zur Vermeidung von Stromschlaggefahr müssen das Rack selbst und alle darin
eingebauten Geräte ordnungsgemäß geerdet sein.
Elektrostatische Entladungen (ESD)
Caution: Elektrostatische Entladungen können zur Beschädigung von Festplatten, Platinen und
anderen Komponenten führen. Daher sollten Sie alle Arbeiten an einer ESD-Workstation
ausführen. Steht ein solcher Arbeitsplatz nicht zur Verfügung, erzielen Sie einen gewissen
Schutz vor elektrostatischen Entladungen durch Tragen einer Antistatik-Manschette, die
Sie während der Arbeit zur Erdung an einem beliebigen unlackierten Metallteil des
Computergehäuses befestigen.
Gehen Sie bei der Handhabung von Platinen immer mit größter Vorsicht vor. Sie können
äußerst empfindlich gegenüber elektrostatischer Entladung sein. Halten Sie Platinen nur
an den Kanten fest. Legen Sie die Platinen nach dem Auspacken aus der Schutzhülle oder
nach dem Ausbau aus dem Server mit der Bauelementseite nach oben auf eine geerdete,
statisch entladene Unterlage. Verwenden Sie dazu, sofern verfügbar, eine leitfähige
Schaumstoffunterlage, aber nicht die Schutzhülle der Platine. Ziehen Sie die Platine nicht
über eine Fläche.
Andere Gefahren
Batterieaustausch
Caution: Wird die Batterie unsachgemäß ausgetauscht, besteht Explosionsgefahr. Verwenden Sie
als Ersatz nur die vom Gerätehersteller empfohlene Batterie.
Beachten Sie bei der Entsorgung von Batterien die gültigen Bestimmungen.
Versuchen Sie nicht, eine Batterie aufzuladen.
Versuchen Sie nicht, eine Batterie zu öffnen oder sonstwie zu beschädigen.
Kühlung und Luftstrom
Caution: Verlegen Sie Kabel sorgfältig entsprechend der Anleitung, um Störungen des Luftstroms
und Kühlungsprobleme zu vermeiden.
Zur Gewährleistung des ordnungsgemäßen Kühlungs- und Luftstromverhaltens darf das
System nur mit angebrachten Gehäuseabdeckungen betrieben werden. Die
Inbetriebnahme des Systems ohne Abdeckung kann zur Beschädigung von
Systemkomponenten führen. So bringen Sie die Abdeckung wieder an:
• Vergewissern Sie sich zunächst, daß Sie keine Werkzeuge oder Teile im Gehäuse
vergessen haben.
124
Intel® Server System SR1530SH/SR1530HSH User’s Guide
• Prüfen Sie, ob Kabel, Erweiterungskarten sowie weitere Komponenten
ordnungsgemäß angebracht sind.
• Befestigen Sie die Abdeckungen am Gehäuse des Produkts, wie in dessen Anleitung
beschrieben.
Laser-Peripheriegeräte oder -Komponenten
Caution: Beachten Sie zur Vermeidung von Strahlung und Verletzungen die folgenden Hinweise:
• Öffnen Sie keinesfalls das Gehäuse von Laser-Peripheriegeräten oder LaserKomponenten.
• Laser-Peripheriegeräte oder -Komponenten besitzen keine für den Benutzer
wartungsbedürftigen Teile.
• Schicken Sie das Gerät für Wartungsarbeiten an den Hersteller zurück.
Français
Consignes de securite sur le serveur
Ce document s’applique aux cartes serveur Intel®, au châssis de serveur Intel® (sur pieds
et sur rack) et aux périphériques installés. Pour réduire les risques de dommages
corporels, d’électrocution, d’incendie et de dommages matériels, lisez ce document et
respectez tous les avertissements et précautions mentionnés dans ce guide avant
d’installer ou de mettre à jour votre produit serveur Intel®.
En cas de conflit entre les informations fournies dans ce document et celles livrées avec le
produit ou publiées sur le site Web pour un produit particulier, la documentation du
produit prime.
Votre serveur doit être intégré et entretenu uniquement par des techniciens qualifiés.
Vous devez suivre les informations de ce guide et les instructions d’assemblage des
manuels de serveur pour vérifier et maintenir la conformité avec les certifications et
approbations de produit existantes. Utilisez uniquement les composants décrits et
réglementés spécifiés dans ce guide. L’utilisation d’autres produits/composants annulera
la liste UL et les autres approbations réglementaires du produit, et le produit peut ne pas
être conforme aux autres lois et réglementations locales applicables au produit.
Séurité: avertissements et mises en garde
Pour éviter de vous blesser ou d’endommager votre équipement, lisez et respectez toutes
les informations et consignes de sécurité avant de commencer l’installation du produit.
Les symboles de sécurité suivants peuvent être utilisés tout au long de cette
documentation et peuvent figurer sur le produit ou sur son emballage.
Intel® Server System SR1530SH/SR1530HSH User’s Guide
125
ATTENTION
Indique la présence d’un risque pouvant entraîner des blessures
physiques mineures ou endommager légèrement le matériel si la mise en
garde n’est pas prise en compte.
AVERTISSEMEN
T
Indique la présence d’un risque pouvant entraîner des blessures
corporelles graves si l’avertissement n’est pas pris en compte.
Indique un risque potentiel si les informations signalées ne sont pas prises
en compte.
Indique des risques d’électrocution pouvant entraîner des blessures
corporelles graves ou mortelles si les consignes de sécurité ne sont pas
respectées.
Signale des composants ou des surfaces soumis à des températures
élevées.
Indique de ne pas toucher aux pales de ventilateur, car cela peut entraîner
des blessures.
Indique de débrancher tous les cordons d’alimentation secteur pour
déconnecter l’alimentation.
Veuillez réutiliser la batterie
Domaines d’utilisation prévus
Ce produit a été testé comme équipement informatique (ITE) et peut être installé dans des
bureaux, des écoles, des salles informatiques et des endroits commerciaux similaires.
L’utilisation du présent produit dans des catégories et environnements de produits et
domaines d’application (par exemple, le domaine médical, industriel, résidentiel, les
systèmes d’alarme et les appareils de contrôle) autres qu’ITE doit faire l’objet
d’évaluations supplémentaires.
Sélection d’un emplacement
Le système est conçu pour fonctionner dans un environnement standard de bureau.
Choisissez un emplacement respectant les conditions suivantes :
• Propre, sec et exempt de particules en suspension (autres que la poussière normale
d’une pièce).
• Bien ventilé et à l’écart des sources de chaleur telles que la lumière directe du soleil
et les radiateurs.
• À l’écart des sources de vibration ou des chocs physiques.
• Isolé des champs électromagnétiques importants produits par des appareils
électriques.
126
Intel® Server System SR1530SH/SR1530HSH User’s Guide
• Dans les régions sujettes aux orages magnétiques, nous vous recommandons de
brancher votre système à un suppresseur de surtension et de déconnecter les lignes
de télécommunication de votre modem pendant les orages.
• Équipé d’une prise murale reliée à la terre.
• Équipé d’un espace suffisant pour accéder aux cordons d’alimentation secteur, car
ils servent de disjoncteur principal d’alimentation du produit.
Pratiques de manipulation de l’équipement
Réduisez le risque de dommages personnels ou matériels :
• Conformez-vous aux exigences de médecine du travail et de sécurité lorsque vous
déplacez et soulevez le matériel.
• Utilisez l’assistance mécanique ou toute autre assistance appropriée lorsque vous
déplacez et soulevez le matériel.
• Pour réduire le poids en vue de faciliter la manipulation, retirez tout composant
amovible.
Alimentation et avertissements en matiére d’électricité
Attention:Le bouton d’alimentation, indiqué par le symbole de mise en veille, NE COUPE PAS
complètement l’alimentation secteur du système car le courant de veille 5 V reste actif
lorsque le système est sous tension. Pour couper l’alimentation du système, vous devez
débrancher le cordon d’alimentation secteur de la prise murale. Votre système peut
utiliser plusieurs cordons d’alimentation secteur. Assurez-vous que tous les cordons
d’alimentation sont débranchés. Vous devez les débrancher avant d’ouvrir le châssis,
d’ajouter ou de supprimer un composant non connectable à chaud.
Les alimentations de certains serveurs Intel sont munies de doubles fusibles pôle/neutre:
veuillez observer les précautions d'usage afin d'éviter tout risque d'eléctrocution.
N’essayez pas de modifier ou d’utiliser un cordon d’alimentation secteur s’il ne s’agit pas
du type exact requis. Un cordon secteur est requis pour chaque alimentation système.
Le bloc d’alimentation de ce produit ne contient aucun composant réparable par
l’utilisateur. N’ouvrez pas le bloc d’alimentation. L’intérieur de celui-ci est soumis à des
Intel® Server System SR1530SH/SR1530HSH User’s Guide
127
niveaux dangereux de tension, de courant et d’énergie. Renvoyez-le au fabricant en cas de
problème.
Lorsque vous remplacez un bloc d’alimentation à chaud, débranchez le cordon du bloc
d’alimentation en cours de remplacement avant de le retirer du serveur.
Pour éviter tout risque d’électrocution, mettez le système hors tension et débranchez les
cordons d’alimentation ainsi que les systèmes de télécommunication, réseaux et modems
reliés au système avant d’ouvrir ce dernier.
Avertissements sur le cordon d’alimentation
Si aucun cordon d’alimentation secteur n’a été fourni avec votre produit, vous devez vous
en procurer un qui soit approuvé pour une utilisation dans votre pays.
Attention:Pour éviter tout risque d’électrocution ou d’incendie, vérifiez les cordons d’alimentation
qui seront utilisés avec le produit comme suit :
• N’essayez pas d’utiliser ou de modifier les cordons d’alimentation en CA s’ils ne
correspondent pas exactement au type requis pour les prises électriques reliées à la
terre.
• Les cordons d’alimentation doivent répondre aux critères suivants :
—
Le cordon d’alimentation doit supporter une intensité supérieure à celle
indiquée sur le produit.
—
Le cordon d’alimentation doit posséder une broche ou un contact de mise à la
terre approprié à la prise électrique.
• Les cordons d’alimentation électrique représentent le principal dispositif de
déconnexion raccordé à l’alimentation secteur. Les prises de courant doivent se
trouver à proximité de l’équipement et être facilement accessibles pour une
déconnexion.
• Les cordons d’alimentation doivent être branchés sur des prises électriques
correctement reliées à la terre.
Avertissements sur l’accés au systéme
Attention:Pour éviter de vous blesser ou d’endommager votre équipement, les consignes de sécurité
suivantes s’appliquent chaque fois que vous accédez à l’intérieur du produit :
• Mettez hors tension tous les périphériques connectés à ce produit.
• Éteignez le système en appuyant sur le bouton d’alimentation.
• Déconnectez l’alimentation secteur en débranchant tous les cordons d’alimentation
secteur du système ou de la prise murale.
• Déconnectez l’ensemble des câbles et lignes de télécommunication qui sont
connectés au système.
128
Intel® Server System SR1530SH/SR1530HSH User’s Guide
• Mettez toutes les vis ou autres attaches de côté lorsque vous retirez les panneaux
d’accès. Une fois que vous avez terminé d’accéder à l’intérieur du produit, refixez le
panneau d’accès avec les vis ou attaches d’origine.
• N’essayez pas d’accéder à l’intérieur du bloc d’alimentation. Il ne contient aucune
pièce réparable. Renvoyez-le au fabricant en cas de problème.
• Mettez le serveur hors tension et débranchez tous les cordons d’alimentation avant
d’ajouter ou de remplacer tout composant non connectable à chaud.
• Lorsque vous remplacez le bloc d’alimentation à chaud, débranchez le cordon du
bloc d’alimentation en cours de remplacement avant de retirer le bloc du serveur.
Attention:Si le serveur a été utilisé, les processeurs et dissipateurs de chaleur installés peuvent être
chauds. À moins que vous n’ajoutiez ou ne retiriez un composant connectable à chaud,
laissez le système refroidir avant d’ouvrir les panneaux. Pour éviter tout risque d’entrer
en contact avec un composant chaud lors d’une installation à chaud, prenez toutes les
précautions nécessaires lorsque vous retirez ou installez des composants connectables à
chaud.
Attention:Pour éviter de vous blesser, ne touchez pas les pales de ventilateur en mouvement. Si votre
système est fourni avec une protection sur le ventilateur, ne mettez pas le système en route
sans la protection en place.
Avertissements sur le montage en rack
Le rack doit être fixé à un support inamovible pour éviter qu’il ne bascule lors de
l’extension d’un serveur ou d’un élément de l’équipement. Le rack doit être installé
conformément aux instructions du fabricant.
Installez les équipements dans le rack en partant du bas, en plaçant le plus lourd en bas du
rack.
N’étendez qu’un seul élément de l’équipement à partir du rack à la fois.
Vous êtes responsable de l’installation d’un disjoncteur principal d’alimentation pour la
totalité du rack. Ce disjoncteur principal doit être rapidement accessible et doit être
étiqueté comme contrôlant toute l’unité, et pas uniquement le ou les serveurs.
Pour éviter tout risque d’électrocution, le rack et chaque élément de l’équipement installé
dans le rack doivent être correctement reliés à la terre.
Intel® Server System SR1530SH/SR1530HSH User’s Guide
129
Décharges électrostatiques (ESD)
Attention:Les décharges électrostatiques (ESD) peuvent endommager les lecteurs de disque dur, les
cartes et d’autres pièces. Il est fortement conseillé d’effectuer l’ensemble des procédures
décrites à un poste de travail protégé contre les ESD. Au cas où aucun poste de ce type ne
serait disponible, protégez-vous contre les ESD en portant un bracelet antistatique relié à
la masse du châssis (n’importe quelle surface métallique non peinte) de votre serveur
lorsque que vous manipulez les pièces.
Manipulez toujours les cartes avec précaution. Elles peuvent être extrêmement sensibles
aux ESD. Ne tenez les cartes que par leurs bords. Après avoir retiré une carte de son
emballage de protection ou du serveur, placez-la sur une surface reliée à la terre, exempte
de charge statique, composants orientés vers le haut. Utilisez si possible un tapis de
mousse conducteur, mais pas l’emballage de la carte. Veillez à ce que la carte ne glisse
sur aucune surface.
Autres risques
Remplacement de la pile
Attention:Il existe un risque d’explosion si la pile n’est pas correctement remplacée. Lors du
remplacement de la pile, utilisez uniquement celle recommandée par le fabricant du
matériel.
Mettez la pile au rebut en vous conformant aux réglementations locales.
N’essayez pas de recharger une pile.
N’essayez pas de démonter, de percer ou d’endommager la pile d’une quelconque façon.
Refroidissement et ventilation
Attention:Routez les câbles avec précaution comme indiqué pour minimiser les blocages de
circulation d’air et les problèmes de refroidissement.
Afin de permettre une ventilation et un refroidissement corrects, ne mettez le système en
marche que lorsque les panneaux du châssis sont en place. L’utilisation du système sans
les panneaux peut endommager les composants système. Pour installer les panneaux :
• Vérifiez tout d’abord que vous n’avez pas oublié d’outils ou de composants détachés
à l’intérieur du système.
• Vérifiez que les câbles, les cartes d’extension et les autres composants sont
correctement installés.
• Fixez les panneaux au châssis en suivant les instructions du produit.
130
Intel® Server System SR1530SH/SR1530HSH User’s Guide
Périphériques laser
Attention:Pour éviter tout risque d’exposition aux rayonnements et/ou de dommage personnel:
• N’ouvrez pas l’enceinte d’un périphérique laser.
• Les périphériques laser ne sont pas réparables par l’utilisateur.
• Retournez-les au fabricant en cas de problème.
Español
Información de seguridad del servidor
Este documento se aplica a las tarjetas de servidor de Intel®, las carcasas de servidor de
Intel® (montaje en bastidor y en pedestal) y los dispositivos periféricos. Para reducir el
riesgo de daños corporales, descargas eléctricas, fuego y en el equipo, lea este documento
y preste atención a todos las advertencias y precauciones de esta guía antes de instalar o
mantener el producto de servidor de Intel®.
En el caso de que haya diferencias entre la información para un producto en particular
contenida en este documento y la información proporcionada con dicho producto o en el
sitio Web, la documentación del producto es la que prevalece.
Sólo personal técnico cualificado debe montar y prestar los servicios para el servidor.
Debe ceñirse a las directrices de esta guía y a las instrucciones de montaje de los manuales
del servidor para asegurar y mantener el cumplimiento con las certificaciones y
homologaciones existentes de los productos. Utilice sólo los componentes descritos y
homologados que se especifican en esta guía. El uso de otros productos o componentes
anulará la homologación UL y otras certificaciones oficiales del producto, pudiendo dejar
de ser compatible con las normativas locales de los países en los que se comercializa.
Advertencias y precauciones sobre seguridad
Para reducir la posibilidad de que se produzcan lesiones personales o daños en la
propiedad, antes de empezar a instalar el producto, lea, observe y cumpla toda la
información e instrucciones de seguridad siguientes. Puede que se utilicen los siguientes
símbolos de seguridad en la documentación y es posible que aparezcan en el producto o en
su embalaje.
PRECAUCIÓN
Indica la existencia de un riesgo que podría causar lesiones personales o
daños en la propiedad leves si no se tiene en cuenta la PRECAUCIÓN.
ADVERTENCIA
Indica la existencia de un riesgo que podría causar lesiones personales
graves si no se tiene en cuenta la ADVERTENCIA.
Intel® Server System SR1530SH/SR1530HSH User’s Guide
131
Indica un riesgo potencial si no se tiene en cuenta la información indicada.
Indica riesgo de descargas eléctricas que podrían causar lesiones graves o
la muerte si no se siguen las instrucciones de seguridad.
Indica componentes o superficies calientes.
Indica que no se deben tocar las aspas de los ventiladores, ya que de lo
contrario se podrían producir lesiones.
Indica que es necesario desenchufar los cables de alimentación de CA para
desconectar la alimentación de CA
Recicle por favor la batería
Aplicaciones y usos previstos
Este producto ha sido evaluado como equipo de tecnología informática (ITE) que puede
instalarse en oficinas, escuelas, salas de equipos informáticos o lugares de ámbito
comercial similares. Es posible que sea necesario llevar a cabo una evaluación adicional
para comprobar si este producto es apropiado para otras categorías de productos y
entornos además de las aplicaciones informáticas (por ejemplo, soluciones médicas,
industriales, residenciales, sistemas de alarma y equipos de pruebas).
Seleccién de la ubicación
El sistema se ha diseñado para funcionar en un entorno normal de oficinas. Seleccione una
ubicación que esté:
• Limpia, seca y libre de macropartículas en suspensión en el aire (que no sean el
polvo habitual de la habitación).
• Bien ventilada y alejada de fuentes de calor, incluida la luz solar directa y los
radiadores.
• Alejada de fuentes de vibración o de golpes físicos.
• Aislada de campos electromagnéticos producidos por dispositivos eléctricos.
• En zonas propensas a tormentas eléctricas, se recomienda que conecte el servidor a
un supresor de sobretensiones y desconecte las líneas de telecomunicaciones al
módem durante una tormenta eléctrica.
• Provista de una toma de corriente alterna correctamente conectada a tierra.
• Provista de espacio suficiente para acceder a los cables de la fuente de alimentación
ya que constituyen la desconexión principal de la alimentación.
132
Intel® Server System SR1530SH/SR1530HSH User’s Guide
Manipulacién del equipo
Reduzca el riesgo de daños personales o en el equipo:
• Respete los requisitos de sanidad y seguridad laborales de su país cuando traslade y
levante el equipo.
• Utilice medios mecánicos u otros que sean adecuados al trasladar o levantar el
equipo.
• Para que el peso sea menor para manipularlo con más facilidad, extraiga los
componentes que sean de fácil extracción.
Advertencias de alimentacién y eléctricas
Precaución: El botón de encendido, indicado con la marca del modo de reposo o stand-by, NO
DESCONECTA completamente la alimentación de CA del sistema, ya que el modo de
reposo de 5 V sigue activo mientras el sistema está enchufado. Para desconectar el
sistema debe desenchufar el cable de alimentación de CA de la toma de la pared. Puede
usar más de un cable de alimentación de CA con el sistema. Asegúrese de que todos los
cables de alimentación de CA están desenchufados. Asegúrese de que los cables de
alimentación de CA estén desenchufado antes de abrir la carcasa, agregar o extraer
cualquier componente que no es de conexión en funcionamiento.
Algunas fuentes de alimentación de electricidad de los servidores de Intel utilizan el polo
neutral del fuselaje. Para evitar riesgos de choques electricos use precauciónes al
trabajar con las fuentes de alimentación que utilizan el polo neutral de fuselaje.
No intente modificar ni utilizar un cable de alimentación de CA si no es del tipo exacto
requerido. Se necesita un cable de CA para cada fuente de alimentación del sistema.
La fuente de alimentación de este producto no contiene piezas que puedan ser reparadas
por el usuario. No abra la fuente de alimentación. Dentro de la fuente de alimentación
puede haber niveles de tensión, corriente y energía peligrosos. Devuélvala al fabricante
para repararla.
Al reemplazar una fuente de alimentación de conexión en funcionamiento, desenchufe el
cable de alimentación de la fuente de alimentación que va a reemplazar antes de extraerla
del servidor.
Para evitar el riesgo de descargas eléctricas, antes de abrir el servidor, apáguelo,
desconecte el cable de alimentación, los sistemas de telecomunicaciones, las redes y los
módems conectados al mismo.
Advertencias sobre el cable de alimentación
Si no se ha proporcionado con el producto ningún cable de alimentación de CA, adquiera
alguno cuyo uso esté aprobado en su país.
Intel® Server System SR1530SH/SR1530HSH User’s Guide
133
Precaución: Para evitar descargas eléctricas o fuego, revise los cables de alimentación que usará con
el producto tal y como se describe a continuación:
• No intente modificar ni utilizar los cables de alimentación de CA si no son
exactamente del modelo especificado para ajustarse a las tomas de corriente
conectadas a tierra.
• Los cables de alimentación deben reunir los siguientes requisitos:
—
El cable de alimentación debe disponer de una capacidad nominal de corriente
eléctrica mayor que la capacidad especificada en el producto.
—
El cable de alimentación debe disponer de una patilla o contacto de conexión a
tierra que sea apto para la toma de corriente.
• Los cables de la fuente de alimentación son los dispositivos de desconexión
principales a la corriente alterna. El enchufe o enchufes de zócalo deben
encontrarse cerca del equipo y el acceso a ellos debe poderse efectuar de forma
inmediata con el fin de desconectarlos.
• Los cables de la fuente de alimentación deben estar conectados a los enchufes con
una toma de tierra adecuada.
Advertencias el acceso al sistema
Precaución: Para evitar lesiones personales o daños en la propiedad, se aplican las siguientes
instrucciones de seguridad siempre que se acceda al interior del producto:
• Apague todos los dispositivos periféricos conectados a este producto.
• Pulse el botón de alimentación para apagar el sistema.
• Desconecte la alimentación de CA desenchufando los cables de alimentación de CA
del sistema o de la toma de corriente alterna.
• Desconecte todos los cables y líneas de telecomunicación que estén conectados al
sistema.
• Guarde todos los tornillos o elementos de fijación cuando retire las cubiertas de
acceso. Cuando termine de operar en el interior del producto, vuelva a colocar los
tornillos o los elementos de fijación originales de la cubierta de acceso.
• No acceda al interior de la fuente de alimentación. No hay elementos en la fuente de
alimentación que usted pueda reparar y utilizar. Devuélvala al fabricante para
repararla.
• Apague el servidor y desconecte todos los cables de alimentación antes de agregar
o reemplazar cualquier componente que no es de conexión en funcionamiento.
134
Intel® Server System SR1530SH/SR1530HSH User’s Guide
• Al reemplazar una fuente de alimentación de conexión en funcionamiento,
desenchufe el cable de alimentación de la fuente de alimentación que va a
reemplazar antes de extraerla del servidor.
Precaución: Si el servidor se ha estado ejecutando, los procesadores y disipadores de calor estarán
recalentados. A no ser que esté instalando o extrayendo un componente de conexión en
funcionamiento, deje que el sistema se enfríe antes de abrir las cubiertas. Para que no
llegue a tocar los componentes que estén calientes cuando esté realizando una instalación
de conexión en funcionamiento, tenga cuidado al extraer o instalar los componentes de
conexión en funcionamiento.
Intel® Server System SR1530SH/SR1530HSH User’s Guide
135
Precaución: Para evitar posibles daños, no toque las aspas en movimiento de los ventiladores. Si el
sistema se le ha suministrado con una protección para el ventilador, asegúrese de que
cuando esté funcionando el sistema la protección esté en su sitio.
Advertencias sobre el montaje en bastidor
El bastidor del equipo se debe sujetar con un soporte fijo para evitar que se caiga cuando
se extraiga un servidor o una pieza del mismo. El bastidor del equipo debe instalarse
siguiendo las instrucciones del fabricante del bastidor.
Instale el equipo en el bastidor comenzando desde la parte de abajo, con el equipo más
pesado en la parte inferior del bastidor.
Extraiga las piezas del equipo del bastidor de una a una.
El usuario es el responsable de la instalación de un dispositivo de desconexión de la
alimentación principal para toda la unidad del bastidor. El acceso a este dispositivo de
desconexión deberá ser de fácil acceso y deberán incluirse indicaciones que lo
identifiquen como el control de alimentación eléctrica de toda la unidad, no sólo de los
servidores.
Para evitar el riesgo de descargas eléctricas, deberá instalar una conexión a tierra
apropiada para el bastidor y para cada pieza del equipo instalada en el mismo.
Descarga electrostática (ESD)
Precaución: Las descargas electrostáticas pueden dañar las unidades de disco, las tarjetas y otros
componentes. Recomendamos que realice todos los procedimientos en una estación de
trabajo protegida contra descargas electrostáticas. En caso de que no haya una
disponible, protéjase de alguna forma contras las descargas llevando un brazalete
antiestático conectado a la toma de tierra de la carcasa (cualquier superficie de metal
que no esté pintada) del servidor cuando manipule las piezas.
Manipule siempre las tarjetas con el máximo cuidado. Pueden ser sumamente sensibles a
las descargas electrostáticas. Sujételas sólo por los bordes. Una vez extraída la tarjeta de
su envoltorio de protección o del servidor, colóquela con el lado de los componentes
hacia arriba sobre una superficie con toma de tierra y sin carga estática. Utilice una
136
Intel® Server System SR1530SH/SR1530HSH User’s Guide
almohadilla de espuma conductora si dispone de ella, pero nunca el envoltorio de la
tarjeta. No deslice la tarjeta sobre ninguna superficie.
Otros riesgos
Sustitución de la batería
Precaución: Existe el peligro de explosión si la batería no se reemplaza correctamente. Al reemplazar
la batería, utilice sólo la batería recomendada por el fabricante del equipo.
Deseche las baterías respetando la normativa local.
No intente recargar la batería.
No intente desmontar, pinchar o causar cualquier otro desperfecto a una batería.
Enfriamiento y circulación de aire
Precaución: El tendido de los cables debe realizarse cuidadosamente tal y como se le indica para
reducir al mínimo los problemas de obstrucción de la ventilación y de refrigeración.
Para conseguir una refrigeración y corriente de aire adecuadas, compruebe que cuando
sistema esté funcionando, las cubiertas de la carcasa están instaladas. Si utiliza el sistema
sin las cubiertas, podría dañar sus componentes. Para instalar las cubiertas:
• Compruebe primero que no ha dejado herramientas o piezas sueltas dentro del
sistema.
• Compruebe que los cables, tarjetas adicionales y otros componentes están
instalados correctamente.
• Sujete las cubiertas a la carcasa siguiendo las instrucciones del producto.
Periféricos o dispositivos láser
Precaución Para evitar el riesgo de la exposición a radiaciones o de daños personales:
• No abra la caja de ningún periférico o dispositivo láser
• Los periféricos o dispositivos láser no pueden ser reparados por el usuario
• Haga que el fabricante los repare
Intel® Server System SR1530SH/SR1530HSH User’s Guide
137
简体中文
服务器安全信息
本 文档 适用 于 Intel® 服 务器 主板 、Intel®
服 务器 机箱 (基 座和 机架 固定 件) 和已 安装 的外 设。 为减 少人 身伤 害、
电 击、 火灾 以及 设备 毁坏 的危 险, 请在 安装 或维 护 Intel®
服 务器 产品 之前 阅读 本文 档并 遵循 本指 南中 的所 有警 告和 预防 措施 。
如 果本 文档 中的 信息 与特 定产 品的 随附 信息 或 Web
站 点信 息之 间存 在不 一致 ,请 以产 品文 档为 准。
服 务器 须由 合格 的技 术人 员进 行集 成和 维护 。
必 须遵 守本 指南 的规 定和 服务 器手 册的 装配 指导 ,以 确保 符合 现有 的产
品 认证 和审 批。 仅使 用本 指南 中描 述和 规定 的指 定组 件。 使用 其他 产品
/ 组件 将使 产品 的 UL
认 证和 其他 管理 审批 无效 ,并 可能 导致 产品 不符 合销 售地 的产 品法 规。
安全警告与注意事项
为 避免 人身 伤害 与财 产损 失, 安装 本产 品之 前, 请阅 读以 下所 有安 全指
导 和信 息。 下面 所列 的安 全符 号可 能在 整个 文档 中使 用并 可能 标注 于产
品 和 / 或产 品包 装之 上。
注意
表 示 如 果 无 视 此 ”注 意 事 项 ”, 存 在 可 能 引 起 轻 微 人 身 伤 害 或 财 产 损 失 的 危 险 。
警告
表 示 如 果 无 视 此 ”警 告 ”, 存 在 可 能 引 起 严 重 人 身 伤 害 的 危 险 。
表示如果无视所示信息,即存在潜在的危险。
表示如果不遵守安全指导,存在可导致严重伤害或死亡的电击危险。
表示灼热组件或表面。
表示请勿触摸风机叶片,否则可能致伤。
表示拔下所有交流电线,断开交流电源
138
Intel® Server System SR1530SH/SR1530HSH User’s Guide
预期应用使用
根据评估,本产品为信息技术设备
(ITE),可安装在办公室、学校、计算机房和类似的商业场所。本产品对于非 ITE
应用的其他产品种类和环境(如医疗、工业、住宅、报警系统和测试设备)的适用
性尚有待进一步的评估。
场地选择
本系统专为在典型办公环境运行而设计。请选择符合以下条件的地点:
•
•
•
•
•
•
•
清洁、干燥,无气载微粒(而非一般的室内尘埃)。
通风良好,远离热源(包括直接日晒和散热器)。
远离振动源或物理震动。
与电气设备产生的强大电磁场隔离。
在易受闪电袭击的地区,我们建议将系统插入电涌抑制器并在闪电期间断开通信
线路与调制解调器之间的连接。
提供正确接地的墙壁插座。
提供足够的空间,以便拿取电源供应线,因为这是本产品的主要电源断开器。
设备操作规范
减少人身伤害或设备受损的危险:
•
•
•
移举设备时遵守当地的职业健康与安全要求。
借助机械手段或其他合适的手段移举设备。
拆除一切易分离组件,以降低重量并方便操作。
电源与电气警告
注意事项
电源按钮(如待机电源标记所示)并不能完全关闭系统的交流电源,只要系统已接
通电源,就存在 5V
待机电源。要从系统切断电源,须从墙壁电源插座中拔下交流电线。您的系统可能
不止使用一根交流电线。请确保所有的交流电线都已拔下。打开机箱或增加或去除
任何热插拔组件之前,确保交流电线已拔下。
若非所需的确切类型,请勿尝试修改或使用交流电线。系统的每个电源供应设备都
需要一根单独的交流电线。
本产品的电源供应设备包含非用户维修部件。请勿打开电源供应设备。电源供应设
备包含非常危险的电压级、电流级和能量级。请与生产商联系维修事宜。
替换热插拔电源供应设备时,请先拔下需替换的电源供应设备上的电源线,再将其
从服务器上移除。
Intel® Server System SR1530SH/SR1530HSH User’s Guide
139
为避免电击,请在打开服务器之前,关闭服务器并断开服务器上连接的电源线、电
信系统、网络和调制解调器。
电源线警告
如果产品未提供交流电线,请购买一根您所在国家批准使用的交流电线。
注意事项
为避免电击或火灾危险,请按如下所述对产品所用的电源线进行检查:
•
•
•
•
若非所需的符合接地插座的确切类型,请勿尝试修改或使用交流电线
电源线须符合以下标准:
⎯ 电源线的电气额定值须大于产品上标注的电流额定值。
⎯ 电源线须拥有适合插座的安全接地插头或触点。
电源线为交流电源的主要断开设备。插座须靠近设备并可随时断开。
电源线须插入所提供的拥有合适接地的插座。
系统使用警告
注意事项
为避免人身伤害或财产损失,无论何时检查产品内部,以下安全指导都适用:
•
•
•
•
•
•
•
•
关闭所有与本产品相连的外设。
按下电源按钮至关闭状态,关闭系统。
从系统或墙壁插座上拔下所有交流电线,断开交流电源。
断开与系统相连的所有线缆和通信线路。
卸除舱口盖时,保留所有螺钉及其他紧固件。完成产品内部检查之后,请
用螺钉或紧固件重新固定舱口盖。
请勿打开电源供应设备。电源供应设备内没有可维修部件。请与生产商联系
维修事宜.
增加或替换任何非热插拔组件之前,请关闭服务器电源并断开所有电源线
。
替换热插拔电源供应设备时,请先拔下需替换的电源供应设备上的电源线
,然后再从服务器上移除电源供应设备。
注意事项
如果服务器一直在运行,任何已安装的处理器和吸热设备都可能很热。除非要增加
或移除热插拔组件,否则请待系统冷却后再开盖。为避免在热插拔组件安装过程中
接触灼热组件,移除或安装热插拔组件时务须小心。
140
Intel® Server System SR1530SH/SR1530HSH User’s Guide
注意事项
为避免受伤,请勿触摸运转的风机叶片。如果系统的风机上配有防护装置,请勿卸
下风机防护装置运行系统。
机架固定件警告
设备的机架须固定在稳固的支座上,以防从中安装服务器或设备时倒塌。须按照机
架生产商提供的安装说明进行安装。
从下往上将设备安装在机架上,最重的设备安装在机架的最底层。
一次只从机架上安装一件设备。
您须负责安装整个机架装置的主要电源断开设备。此主要断开设备须随时可用,且
须标明为控制整个装置(而不仅限于服务器)的电源。
为避免潜在的电击危险,须对机架及其上所安装的每一件设备实行正确的安全接地
。
静电放电 (ESD)
注意事项
ESD 会损坏磁盘驱动器、主板及其他部件。我们建议您执行 ESD
工作站的所有步骤。如果没有 ESD
工作站,则采取一些静电放电保护措施,操作部件时,戴上与服务器上的机箱接地
或任何未喷漆金属表面连接的防静电腕带。
操作主板时始终保持小心。它们可能对 ESD
非常敏感。拿持主板时只接触边缘。从保护包装中或从服务器上取出主板后,请将
主板组件侧面朝上放置在无静电的接地表面上。请使用导电泡沫垫(若有),不要
使用主板包装。请勿将主板在任何表面上滑动。
Intel® Server System SR1530SH/SR1530HSH User’s Guide
141
其他危险
替换电池
注意事项
不正确替换电池可能导致爆炸危险。替换电池时,请只使用设备生产商推荐使用的
电池。
请按当地法规处置电池。
请勿对电池充电。
请勿拆卸、刺穿或以其他方式损坏电池。
冷却和气流
注意事项
按照说明小心布置线缆,尽量减少气流阻塞和冷却问题。
为保证适当的冷却和气流,运行系统时请确保机箱盖已安装。未安装机箱盖即运行
系统可能导致系统部件受损。安装机箱盖的步骤如下:
•
•
•
首先检查并确保系统内没有遗留的未固定工具或部件。
检查线缆、内插板和其他组件已正确安装。
按产品说明安装机箱盖。
激光外设或激光设备
注意事项
为避免幅射暴露和 / 或人身伤害:
•
请勿打开任何激光外设或激光设备的外壳
•
激光外设或激光设备为非用户维修设备
请与生产商联系维修事宜
142
Intel® Server System SR1530SH/SR1530HSH User’s Guide
Appendix E: Regulatory and
Compliance Information
Product Regulatory Compliance
Warning: To ensure regulatory compliance, you must adhere to the assembly instructions in this
guide to ensure and maintain compliance with existing product certifications and
approvals. Use only the described, regulated components specified in this guide. Use of
other products/components will void the UL listing and other regulatory approvals of the
product and will most likely result in noncompliance with product regulations in the
region(s) in which the product is sold.
To help ensure EMC compliance with your local regional rules and regulations, before
computer integration, make sure that the server system, power supply, and other modules
have passed EMC testing using a server board with a microprocessor from the same
family (or higher) and operating at the same (or higher) speed as the microprocessor used
on this server board. The final configuration of your end system product may require
additional EMC compliance testing. For more information, please contact your local Intel
representative.
This is an FCC Class A device. Integration of it into a Class B system does not result in a
Class B device.
Product Safety Compliance
This server system product, when correctly integrated per this guide, complies with the
following safety and electromagnetic compatibility (EMC) regulations.
Intended Application
This product was evaluated as Information Technology Equipment (ITE), which may be
installed in offices, schools, computer rooms, and similar commercial type locations. The
suitability of this product for other product categories and environments (such as: medical,
industrial, telecommunications, NEBS, residential, alarm systems, test equipment, etc.),
other than an ITE application, may require further evaluation.
Product Safety Compliance
The server system complies with the following product safety requirements:
• UL60950 - CSA 60950 (USA/Canada)
• EN60950 (Europe)
• IEC60950 (International)
Intel® Server System SR1530SH/SR1530HSH User’s Guide
143
• CB Certificate & Report, IEC60950 (report to include all country national
deviations)
• GS License (Germany)
•
•
•
•
•
GOST R 50377-92 - License (Russia)
Belarus License (Belarus)
Ukraine License (Ukraine)
CE - Low Voltage Directive 73/23/EEE (Europe)
IRAM Certification (Argentina)
Product EMC Compliance - Class A Compliance
This server system has been tested and verified to comply with the following
electromagnetic compatibility (EMC) regulations when installed in a compatible Intel®
host system. For information on compatible host system(s) refer to Intel's Server Builder
Web site or contact your local Intel representative.
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
144
FCC /ICES-003 - Emissions (USA/Canada) Verification
CISPR 22 - Emissions (International)
EN55022 - Emissions (Europe)
EN55024 - Immunity (Europe)
EN61000-3-2 - Harmonics (Europe)
EN61000-3-3 - Voltage Flicker (Europe)
CE - EMC Directive 89/336/EEC (Europe)
VCCI Emissions (Japan)
AS/NZS 3548 Emissions (Australia/New Zealand)
BSMI CNS13438 Emissions (Taiwan)
GOST R 29216-91 Emissions (Russia)
GOST R 50628-95 Immunity (Russia)
Belarus License (Belarus)
Ukraine License (Ukraine)
RRL MIC Notice No. 1997-41 (EMC) & 1997-42 (EMI) (Korea)
Intel® Server System SR1530SH/SR1530HSH User’s Guide
Certifications/Registrations/Declarations
•
•
•
•
•
•
•
•
•
•
•
•
UL Certification (US/Canada)
CE Declaration of Conformity (CENELEC Europe)
FCC/ICES-003 Class A Attestation (USA/Canada)
VCCI Certification (Japan)
C-Tick Declaration of Conformity (Australia)
MED Declaration of Conformity (New Zealand)
BSMI Certification (Taiwan)
GOST R Certification/License (Russia)
Belarus Certification/License (Belarus)
RRL Certification (Korea)
IRAM Certification (Argentina)
Ecology Declaration (International)
Product Regulatory Compliance Markings
This Intel® server system product is provided with the following regulatory marks.
Table 10. Product Regulatory Compliance Markings
Regulatory Compliance
Region
cULus Listing Marks
USA/Canada
GS Mark
Germany
CE Mark
Europe
FCC Marking (Class A)
USA
EMC Marking (Class A)
Canada
Intel® Server System SR1530SH/SR1530HSH User’s Guide
Marking
145
Table 10. Product Regulatory Compliance Markings
Regulatory Compliance
146
Region
C-Tick Mark
Australia/New
Zealand
VCCI Marking (Class A)
Japan
BSMI Certification
Number & Class A
Warning
Taiwan
GOST R Marking
Russia
RRL MIC Mark
Korea
Marking
Intel® Server System SR1530SH/SR1530HSH User’s Guide
Electromagnetic Compatibility Notices
FCC Verification Statement (USA)
This device complies with Part 15 of the FCC Rules. Operation is subject to the following
two conditions: (1) this device may not cause harmful interference, and (2) this device
must accept any interference received, including interference that may cause undesired
operation.
For questions related to the EMC performance of this product, contact:
Intel Corporation
5200 N.E. Elam Young Parkway
Hillsboro, OR 97124-6497
1-800-628-8686
This equipment has been tested and found to comply with the limits for a Class A digital
device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide
reasonable protection against harmful interference in a residential installation. This
equipment generates, uses, and can radiate radio frequency energy and, if not installed and
used in accordance with the instructions, may cause harmful interference to radio
communications. However, there is no guarantee that interference will not occur in a
particular installation. If this equipment does cause harmful interference to radio or
television reception, which can be determined by turning the equipment off and on, the
user is encouraged to try to correct the interference by one or more of the following
measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and the receiver.
• Connect the equipment to an outlet on a circuit other than the one to which the
receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.
Any changes or modifications not expressly approved by the grantee of this device could
void the user's authority to operate the equipment. The customer is responsible for
ensuring compliance of the modified product.
Only peripherals (computer input/output devices, terminals, printers, etc.) that comply
with FCC Class A or B limits may be attached to this computer product. Operation with
noncompliant peripherals is likely to result in interference to radio and TV reception.
All cables used to connect to peripherals must be shielded and grounded. Operation with
cables, connected to peripherals, that are not shielded and grounded may result in
interference to radio and TV reception.
Intel® Server System SR1530SH/SR1530HSH User’s Guide
147
Industry Canada (ICES-003)
Cet appareil numérique respecte les limites bruits radioélectriques applicables aux
appareils numériques de Classe A prescrites dans la norme sur le matériel brouilleur:
"Apparelis Numériques", NMB-003 édictee par le Ministre Canadian des
Communications.
English translation of the notice above:
This digital apparatus does not exceed the Class A limits for radio noise emissions from
digital apparatus set out in the interference-causing equipment standard entitled: "Digital
Apparatus," ICES-003 of the Canadian Department of Communications.
Europe (CE Declaration of Conformity)
This product has been tested in accordance to, and complies with the Low Voltage
Directive (73/23/EEC) and EMC Directive (89/336/EEC). The product has been marked
with the CE Mark to illustrate its compliance.
VCCI (Japan)
English translation of the preceding notice:
This is a Class A product based on the standard of the Voluntary Control Council for
Interference (VCCI) from Information Technology Equipment. If this is used near a radio
or television receiver in a domestic environment, it may cause radio interference. Install
and use the equipment according to the instruction manual.
BSMI (Taiwan)
The BSMI Certification Marking and EMC warning is located on the outside rear area of
the product.
148
Intel® Server System SR1530SH/SR1530HSH User’s Guide
Korean Compliance (RRL)
Following is the RRL certification information for Korea.
English translation of the notice above:
1. Type of Equipment (Model Name): On License and Product
2. Certification No.: On RRL certificate. Obtain certificate from local Intel
representative
3. Name of Certification Recipient: Intel Corporation
4. Date of Manufacturer: Refer to date code on product
5. Manufacturer/Nation: Intel Corporation/Refer to country of origin marked on
product
Regulated Specified Components
To maintain the UL listing and compliance to other regulatory certifications and/or
declarations, the following regulated components must be used and conditions adhered to.
Interchanging or use of other components will void the UL listing and other product
certifications and approvals.
Updated product information for configurations can be found on the Intel Server Builder
Web site at the following URL: http://channel.intel.com/go/serverbuilder
If you do not have access to Intel's Web address, please contact your local Intel
representative.
• Server Chassis: (base chassis is provided with power supply and fans) - UL listed.
• Server board: you must use an Intel server board - UL recognized.
• Add-in boards: must have a printed wiring board flammability rating of minimum
UL94V-1. Add-in boards containing external power connectors and/or lithium
batteries must be UL recognized or UL listed. Any add-in board containing modem
telecommunication circuitry must be UL listed. In addition, the modem must have
the appropriate telecommunications, safety, and EMC approvals for the region in
which it is sold.
• Peripheral Storage Devices: must be a UL recognized or UL listed accessory and
TUV or VDE licensed. Maximum power rating of any one device is 19 watts. Total
server configuration is not to exceed the maximum loading conditions of the power
supply.
Intel® Server System SR1530SH/SR1530HSH User’s Guide
149
Restriction of Hazardous Substances (RoHS)
Compliance
Intel has a system in place to restrict the use of banned substances in accordance with the
European Directive 2002/95/EC. Compliance is based on declaration that materials
banned in the RoHS Directive are either (1) below all applicable substance threshold
limits or (2) an approved/pending RoHS exemption applies.
Note: RoHS implementation details are not fully defined and may change.
Threshold limits and banned substances are noted below.
• Quantity limit of 0.1% by mass (1000 PPM) for:
— Lead
— Mercury
— Hexavalent Chromium
— Polybrominated Biphenyls Diphenyl Ethers (PBDE)
• Quantity limit of 0.01% by mass (100 PPM) for:
— Cadmium
End-of-Life/Product Recycling
Product recycling and end-of-life take-back systems and requirements vary by country.
Contact the retailer or distributor of this product for information about product recycling
and/or take-back.
150
Intel® Server System SR1530SH/SR1530HSH User’s Guide
Appendix F: Warranty
Limited Warranty for Intel® Chassis
Subassembly Products
Intel warrants that the Products (defined herein as the Intel® chassis subassembly and all
of its various components and software delivered with or as part of the Products) to be
delivered hereunder, if properly used and installed, will be free from defects in material
and workmanship and will substantially conform to Intel's publicly available
specifications for a period of three (3) years after the date the Product was purchased from
an Intel authorized distributor. Software of any kind delivered with or as part of products
is expressly provided "as is" unless specifically provided for otherwise in any software
license accompanying the software.
If any Product furnished by Intel which is the subject of this Limited Warranty fails during
the warranty period for reasons covered by this Limited Warranty, Intel, at its option, will:
• REPAIR the Product by means of hardware and/or software; OR
• REPLACE the Product with another Product; OR
• REFUND the then-current value of the Product if Intel is unable to repair or replace
the Product.
If such Product is defective, transportation charges for the return of Product to buyer
within the USA will be paid by Intel. For all other locations, the warranty excludes all
costs of shipping, customs clearance, and other related charges. Intel will have a
reasonable time to make repairs or to replace Product or to refund the then-current value
of the Product.
In no event will Intel be liable for any other costs associated with the replacement or
repair of Product, including labor, installation or other costs incurred by buyer and in
particular, any costs relating to the removal or replacement of any product soldered or
otherwise permanently affixed to any printed circuit board.
This Limited Warranty, and any implied warranties that may exist under state law, apply
only to the original purchaser of the Product.
Extent of Limited Warranty
Intel does not warrant that Products to be delivered hereunder, whether delivered standalone or integrated with other Products, including without limitation semiconductor
components, will be free from design defects or errors known as "errata." Current
characterized errata are available upon request.
Intel® Server System SR1530SH/SR1530HSH User’s Guide
151
This Limited Warranty does not cover damages due to external causes, including accident,
problems with electrical power, usage not in accordance with product instructions,
misuse, neglect, alteration, repair, improper installation, or improper testing.
Warranty Limitations and Exclusions
These warranties replace all other warranties, expressed or implied including, but not
limited to, the implied warranties of merchantability and fitness for a particular purpose.
Intel makes no expressed warranties beyond those stated here. Intel disclaims all other
warranties, expressed or implied including, without limitation, implied warranties of
merchantability and fitness for a particular purpose. Some jurisdictions do not allow the
exclusion of implied warranties, so this limitation may not apply.
All expressed and implied warranties are limited in duration to the limited warranty
period. No warranties apply after that period. Some jurisdictions do not allow limitations
on how long an implied warranty lasts, so this limitation may not apply to you.
Limitations of Liability
Intel's responsibility under this, or any other warranty, implied or expressed, is limited to
repair, replacement, or refund, as set forth above. These remedies are the sole and
exclusive remedies for any breach of warranty. Intel is not responsible for direct, special,
incidental, or consequential damages resulting from any breach of warranty under another
legal theory including, but not limited to, lost profits, downtime, goodwill, damage to or
replacement of equipment and property, and any costs of recovering, reprogramming, or
reproducing any program or data stored in or used with a system containing this product.
Some jurisdictions do not allow the exclusion or limitation of incidental or consequential
damages, so the above limitations or exclusions may not apply to you.
This limited warranty gives you specific legal rights, and you may also have other rights
that vary from jurisdiction to jurisdiction.
Any and all disputes arising under or related to this Limited Warranty shall be adjudicated
in the following forums and governed by the following laws: for the United States of
America, Canada, North America, and South America, the forum shall be Santa Clara,
California, USA, and the applicable law shall be that of the State of California, USA; for
the Asia Pacific region, the forum shall be Singapore and the applicable law shall be that
of Singapore; for Europe and the rest of the world, the forum shall be London and the
applicable law shall be that of the United Kingdom.
In the event of any conflict between the English language version and any other translated
version(s) of this Limited Warranty, the English language version shall control.
152
Intel® Server System SR1530SH/SR1530HSH User’s Guide
How to Obtain Warranty Service
To obtain warranty service for this Product, you may contact Intel or your authorized
distributor.
• North America and Latin America To obtain warranty repair for the product, please
go to the following Web site to obtain instructions: http://support.intel.com/support/
motherboards/draform.htm
• In Europe and in Asia Contact your original authorized distributor for warranty
service.
Any replacement Product is warranted under this written warranty and is subject to the
same limitations and exclusions for the remainder of the original warranty period.
Telephone Support
If you cannot find the information you need on Intel's World Wide Web site (http://
www.intel.com/), call your local distributor or an Intel Customer Support representative.
See “Getting Help” for telephone numbers.
Returning a Defective Product
Before returning any product, call your authorized dealer/distribution authority.
Intel® Server System SR1530SH/SR1530HSH User’s Guide
153
154
Intel® Server System SR1530SH/SR1530HSH User’s Guide
Appendix G: Getting Help
World Wide Web
http://support.intel.com/support/motherboards/server/S3200SH
Telephone
All calls are billed per incident, levied in local currency at the applicable credit card
exchange rate plus applicable taxes. (Intel reserves the right to change the pricing for
telephone support at any time without notice).
Before calling, fill out an Intel® Server Issue Report Form. You can find a sample form at:
http://support.intel.com/support/motherboards/server/S3200SH. For the fastest service,
please submit your form via the Internet.
For an updated support contact list, see http://www.intel.com/support/9089.htm/
U.S. and Canada
916-377-7000
Europe
Belgium ..... 02 714 3182
Denmark ... 38 487077
Finland ...... 9 693 79297
France........ 01 41 918529
Germany ... 069 9509 6099
Holland ...... 020 487 4562
Italy............ 02 696 33276
Norway ...... 23 1620 50
Spain .......... 91 377 8166
Sweden....... 08 445 1251
UK.............. 870 6072439
Intel® Server System SR1530SH/SR1530HSH User’s Guide
155
In Asia-Pacific region
Australia.... 1800 649931
Cambodia.. 63 2 636 9797 (via Philippines)
China ......... 800 820 1100 (toll-free)
.................... 8 621 33104691 (not toll-free)
Hong Kong 852 2 844 4456
India........... 0006517 2 68303634 (manual toll-free. You need an IDD-equipped
telephone)
Indonesia ... 803 65 7249
Korea ......... 822 767 2595
Malaysia .... 1 800 80 1390
Myanmar... 63 2 636 9796 (via Philippines)
New Zealand 0800 444 365
Pakistan..... 632 63684 15 (IDD via Philippines)
Philippines 1 800 1 651 0117
Singapore .. 65 6213-1311
Taiwan ....... 2 2545-1640
Thailand .... 1 800 631 0003
Vietnam ..... 632 6368416 (IDD via Philippines)
Japan
Domestic.... 0120 868686
Outside country ... 81 298 47 0800
Latin America
Argentina .. Contact AT&T USA at 0-800 222 1288. Once connected, dial 800 843 4481
Brazil ......... 001-916 377 0180
Chile
156
Easter Island.. ............ Contact AT&T USA at 800 800 311. Once
connected, dial 800 843 4481
Mainland and Juan .. Contact AT&T USA at 800 225 288. Once
connected, dial 800 843 4481
Intel® Server System SR1530SH/SR1530HSH User’s Guide
Colombia ... Contact AT&T USA at 01 800 911 0010. Once connected, dial 800 843 4481
Costa Rica . Contact AT&T USA at 0 800 0 114 114. Once connected, dial 800 843 4481
Ecuador
(Andimate) .... Contact AT&T USA at 1 999 119. Once connected,
dial 800 843 4481
(Pacifictel) ..... Contact AT&T USA at 1 800 225 528. Once connected, dial
800 843 4481
Guatemala. Contact AT&T USA at 99 99 190. Once connected, dial 800 843 4481
Mexico ....... Contact AT&T USA at 001 800 462 628 4240. Once connected, dial 800 843
4481
Miami ........ 1 800 621 8423
Panama...... Contact AT&T USA at 00 800 001 0109. Once connected, dial 800 843 4481
Paraguay ... 001 916 377 0114
Peru ........... 001 916 377 0114
Uruguay..... 001 916 377 0114
Venezuela... Contact AT&T USA at 0 800 2255 288. Once connected, dial 800 843 4481
Intel® Server System SR1530SH/SR1530HSH User’s Guide
157
158
Intel® Server System SR1530SH/SR1530HSH User’s Guide
Download PDF
Similar pages