1. Before using 2. Name of parts Contents www.alb.co.kr Manual

Manual Instruction
www.alb.co.kr
2. Name of parts
1
2
3
4
5
C-300
Compact Lighting System
Contents
5
1. Before using
2. Name of parts
3. Functions of control panel
4. Specification
5. Operation
6. Characteristics of Camray
7. Maintainance
8. Trouble shooting
6
7
8
9
10 11
"L" Bracket Assembling
1. Before using
This flash is a very precise photographic equipment therefore don't forget to read this operation
manual very carefully before using.
1. Please read Operation Manual before using it.
2. Input voltage should be checked before use.
3. Don't move or shock when power on. Coil of modeling lamp might be cut off in case of
moving with lamp on.
4. Connect to the properly functioning and grounded 3-pin receptacles only.
5. Attach or disattach reflector, snoot, or other accessories after halogen lamp turned off and
cooled off.
6. Be careful of electric shock when using this equipment in humid places.
7. Keep this equipment where children can not be reached.
8. Keep the subject minium 1m far from the flash.
9. Rated maximum ambient temperature : Ta 25 °C
10. The lamp shall be change if has become damage or them ally deformed.
11. Minimum distance from flammable to all exterior surface the luminary : 1m
1
12 13
14
15
1
Reflector
6
"L" bracket fixing knob
11
Fuse holder & Fuse(250V/10A)
2
Modeling lamp
7
Stand fixing bolt
12
Umbrella Fixing bolt
3
Xenon tube
8
"L" bracket
13
Reflector Fixing bolt
4
Xenon tube plate
9
Synchro socket "X"
14
AC input cord
5
Control panel
10
AC input socket(220/110V)
15
Synchro cord
2
6. Characteristics of Camray
3. Functions of Control Panel
1
① Photocell : Sensor for lights
② Ready : Lighting test, lights up when pressed.
③ Slave : On/off switch for synchro sensor.
- On(Green lamp on) : Operated by synchro
sensor or synchro cord
- Off(Green lamp off) : Operated by synchro
cord only.
④ Alarm : On/off switch for alarm
(checking the charging status)
- On(Green lamp on) : Beeps while being charged,
stops beeping when over.
- Off(Green lamp off) : Resets alarm
⑤ Power : Main power switch
6
- On (Red lamp on)
- Off (Red lamp off)
⑥ Flash : Controler for output volume (1/8 Minimum - 1/1 Maximum)
⑦ Model : Controler for modeling volume ( Minimum - Maximum)
4. Specification
C-300
Max. Output
300W/s
Input voltage
AC 220V 50/60Hz
Recharging time
0.5~2.0sec
Flash Duration
1/700~1/1,600sec
Color Temperature
5500±100 K
Triggering method
Halogen : 100W
Synchro cord, Slave, Test button, IR
Working voltage
Stepless volume control (50~300W/s)
Modeling lamp voltage
Stepless volume control (25~100%)
Output tolerance
±0.1%
Synchro
ON/OFF switch
Alarm
ON/OFF switch
Chasis
Titanium, Aluminium
Size
26×16×10cm
Weight
Items attached
7. Maintenance
5
7
1. How to replace modeling lamp(BASE:E-11 or E-27)
- Cool off and then take out the modeling lamp.
- Be careful not to leave fingerprints or stains on the lamp, clean up the surface of lamp after replacement.
2. How to replace a fuse
- First take out the electricity cord.
- Disassemble fuse holder and take out the fuse.
- Check the fuse is short and replace it with a spare fuse in the fuse holder.
3. How to keep flashes
- Protect pirex dome and xenon tube from dust or stain while being kept
- If there are dust or stain on the pirex dome or xenon tube which lifetime might be shortened or lead lower
color temperature, clean up them with soft fabric.
※ Remarks : It might not recharge fully when a rated voltage is higher than input voltage.
In this case, please check input voltage.
This product can be modified for better quality without prior notice.
1. All powers are lowered and lighting volume is
minimised when the flash was released from the
factory.
2. Check the modeling lamp volume, flash volume,
and the power is turned off before power on.
3. Connect synchro cord to the synchro socket.
8. Trouble Shooting
STATUS
Photo cell does
not operate.
4. Turn on power button(Red lamp on).
5. Never forget to discharge the remaining electric
currency before turns off the mail power.
Snoot, spot, softbox, umbrella, barn-door,
honeycomb grid, bag
Triggering voltage
DC 12V
ESTIMATED CAUSE
TROUBLE SHOOTING
Slave off.
Check whether cell is on or not.
The light does not reach photo cell.
Change the position of flash so that light can reach
the photo cell
Too much light shines photo cell.
Isolate the flash from very strong light.
Dust or stain on the synchro cord jack
Remove dust or stain
Shortened synchro cord or bad connection
Replace it (Check whether it turns on or not by pressing
test button)
No operation
No electricity
- Check if the electricity cord is well inserted.
- Check if the contact of consent is OK.
- Check the fuse.
Others
Please consult A/S center or manufacturer. They will provide you safety, insure proper operational
functions and provide continuation of your warranty.
Synchro cord
does not operate.
1.6kg
Standard reflector, modeling lamp, synchro cord
Options
3
3
4
5. Operation
Subject
Modeling lamp
2
1. Small, lightweight and reasonable price compared to quality and function.
2. Very convenient to control modeling lamp by stepless slide volume and flash volume by touch button.
3. It easy to insert in & out PCBs.
4. Very suitable for portrait, profile, and digital photographing.
5. Umberella reflector, snoot, honeycomb grid, barn-door, softbox, bags are available for customers convenience.
※ This product can be modified for better quality and function without prior notice.
741-1 Sangyeck-dong, Buk-gu, Korea / www.alb.co.kr / e-mail : alb@alb.co.kr
Tel : +82 53 384 9874 / Fax : +82 53 384 9886 / For product consulting, call us :+82 53 384 9870
4
Download PDF
Similar pages