Model No. WV-S6131 / WV-S6111 WV-S6130 - cs.psn

Important Information
Network Camera
Model No.
WV-S6131 / WV-S6111
WV-S6130
LOCK
OPEN
130
-S6
WV
WV-S6131
WV-S6130
* For information about the installation tasks, refer to the provided Installation
Guide. For information about how to perform the settings and how to
operate the camera, refer to the Operating Instructions on the provided
CD-ROM.
Before attempting to connect or operate this product,
please read these instructions carefully and save this manual for future use.
The model number is abbreviated in some descriptions in this manual.
Contents
Limitation of liability........................................................................................................................ 3
Disclaimer of warranty.................................................................................................................... 3
Preface........................................................................................................................................... 4
About notations.............................................................................................................................. 4
Main functions................................................................................................................................ 5
About the user manuals................................................................................................................. 6
System requirements for a PC....................................................................................................... 6
Trademarks and registered trademarks......................................................................................... 7
Copyright........................................................................................................................................ 7
Open Source Software................................................................................................................... 8
Network security............................................................................................................................ 8
Precautions.................................................................................................................................... 9
Precautions for installation........................................................................................................... 13
Parts and functions...................................................................................................................... 15
Insert / remove an SD memory card*........................................................................................... 25
Troubleshooting............................................................................................................................ 27
Specifications............................................................................................................................... 30
Optional accessories.................................................................................................................... 36
* SDXC/SDHC/SD memory card is described as SD memory card.
2
Limitation of liability
THIS PUBLICATION IS PROVIDED “AS IS” WITHOUT WARRANTY OF ANY KIND, EITHER
EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO, THE IMPLIED WARRANTIES OF
MERCHANTABILITY, FITNESS FOR ANY PARTICULAR PURPOSE, OR NON-INFRINGEMENT OF
THE THIRD PARTY'S RIGHT.
THIS PUBLICATION COULD INCLUDE TECHNICAL INACCURACIES OR TYPOGRAPHICAL
ERRORS. CHANGES ARE ADDED TO THE INFORMATION HEREIN, AT ANY TIME, FOR THE
IMPROVEMENTS OF THIS PUBLICATION AND/OR THE CORRESPONDING PRODUCT (S).
Disclaimer of warranty
IN NO EVENT SHALL Panasonic Corporation BE LIABLE TO ANY PARTY OR ANY PERSON,
EXCEPT FOR REPLACEMENT OR REASONABLE MAINTENANCE OF THE PRODUCT, FOR THE
CASES, INCLUDING BUT NOT LIMITED TO BELOW:
(1)ANY LOSS OR DAMAGE, INCLUDING WITHOUT LIMITATION, DIRECT OR INDIRECT,
SPECIAL, CONSEQUENTIAL OR EXEMPLARY, ARISING OUT OF OR RELATING TO THE
PRODUCT;
(2)ANY INCONVENIENCE, LOSS, OR DAMAGE CAUSED BY INAPPROPRIATE USE OR
NEGLIGENT OPERATION OF THE USER;
(3)ALL MALFUNCTIONS OR TROUBLES FROM UNAUTHORIZED DISASSEMBLE, REPAIR OR
MODIFICATION OF THE PRODUCT BY THE USER, REGARDLESS OF THE CAUSE OF THE
MALFUNCTION OR TROUBLE;
(4) INCONVENIENCE OR ANY LOSS ARISING WHEN IMAGES ARE NOT DISPLAYED, DUE TO
ANY REASON OR CAUSE INCLUDING ANY FAILURE OR PROBLEM OF THE PRODUCT;
(5)ANY PROBLEM, CONSEQUENTIAL INCONVENIENCE, OR LOSS OR DAMAGE, ARISING
OUT OF THE SYSTEM COMBINED BY THE DEVICES OF THIRD PARTY;
(6) ANY CLAIM OR ACTION FOR DAMAGES BROUGHT BY ANY PERSON OR ORGANIZATION
AS A PHOTOGRAPHED SUBJECT DUE TO VIOLATION OF PRIVACY CONCERNING A
SURVEILLANCE CAMERA'S PICTURE OR SAVED DATA, FOR SOME REASON (INCLUDING
USE WHEN USER AUTHENTICATION ON THE AUTHENTICATION SETTING SCREEN IS SET
TO OFF), BECOMING PUBLIC OR BEING USED FOR ANY PURPOSE;
(7)LOSS OF REGISTERED DATA CAUSED BY ANY FAILURE (INCLUDING INITIALIZATION OF
THE PRODUCT DUE TO FORGOTTEN AUTHENTICATION INFORMATION SUCH AS A USER
NAME AND PASSWORD).
3
Preface
This product is an indoor use PTZ (PAN, TILT, ZOOM) type monitoring camera with a 10BASET/
100BASE-TX network port for network connection.
By connecting to a network (LAN) or the Internet, images and audio from the camera can be monitored on a PC via a network.
Note:
• It is necessary to configure the network settings of the PC and its network environment to monitor images from the camera on the PC. It is also necessary to install a web browser on the PC.
About notations
The following notations are used when describing the functions limited for specified models.
The functions without the notations are supported by all models.
S6131
The functions with this notation are available when using the model WV-S6131.
S6111
The functions with this notation are available when using the model WV-S6111.
S6130
The functions with this notation are available when using the model WV-S6130.
4
Main functions
S6111
40x optical zoom S6131
, 21x optical zoom
preset position function
A single camera provides wide area monitoring.
S6130
and high accuracy
Delivers high image quality streaming at low bit rates thanks to a H.265 engine equipped
with Panasonic's own Smart Facial Coding technology*1.
This allows H.265 compression in addition to conventional H.264 compression technology, and
when combined with Smart Facial Coding, reduces data load compared to our previous models.
Panasonic's own intelligent auto (iA) feature provides increased discernibility even in
environments with poor visibility
Improvements to the Super Dynamic (SD) feature and shutter speed optimization provides clear
discernibility even when monitoring moving people or car silhouettes or when license plates are illuminated by car headlights. Also, face recognition under the condition where brightness of the background changes is enabled by a function of recognizing face position and adjusting the brightness
automatically.
Equipped with SD memory card slot
It is possible to save H.265 / H.264 videos and JPEG images on the SD memory card manually
when an alarm occurs, during the period of the schedule, or on a Web browser. (Downloading is
possible.) It is also possible to save JPEG images if a network failure occurs.
Encryption and alteration detection functions enhanced the security.
*1 This technology allows the camera to learn the location of faces and moving objects, and transmit only the face portion of the image in high definition, thereby greatly reducing the bandwidth
required.
5
About the user manuals
Product documentation is composed of the following documents.
• Important Information (this document): Provides basic information about the product.
• Installation Guide: Explains installation, cable connections, mounting and removing.
• Operating Instructions (included in the CD-ROM): Explains how to perform the settings and how
to operate this camera.
Adobe® Reader® is required to read these operating instructions on the provided CD-ROM.
When the Adobe Reader is not installed on the PC, download the latest Adobe Reader from the
Adobe web site and install it.
The external appearance and other parts shown in this manual may differ from the actual product
within the scope that will not interfere with normal use due to improvement of the product.
System requirements for a PC
CPU:Intel® CoreTM 2 Duo 2.4 GHz or faster recommended
Memory:
A minimum of 1 GB or more (for 32-bit OSs), 2 GB or more (for 64-bit OSs)
memory is required.
Network interface:
10BASE-T/100BASE-TX 1 port
Audio interface:
Sound card (when using the audio function)
Monitor:
Image capture size: 1024 x 768 pixels or more
Color: 24-bit True color or better
OS:
Microsoft Windows 10
Microsoft Windows 8.1
Microsoft Windows 8
Microsoft Windows 7
Web browser:
Windows Internet Explorer 11 (32-bit)
Windows Internet Explorer 10 (32-bit)
Windows Internet Explorer 9 (32-bit)
Windows Internet Explorer 8 (32-bit)
Others:
CD-ROM drive
(It is necessary to read the operating instructions and use the software on
the provided CD-ROM.)
Adobe® Reader®
(It is necessary to view the PDF file on the provided CD-ROM.)
6
IMPORTANT:
•For information on the operation verification of the supported operating systems and web
browsers, refer to our website at https://security.panasonic.com/support/info/.
•When using a PC that does not meet the above requirements, displaying of images may
become slower or the web browser may become inoperable.
• Audio may not be heard if a sound card is not installed on a PC. Audio may be interrupted
depending on the network environment.
• Microsoft Windows RT, Microsoft Windows 7 Starter and Microsoft Edge are not supported.
• When using Microsoft Windows 8.1, Microsoft Windows 8, use it in the desktop. The software cannot be used in the Modern UI design.
Note:
•For further information about PC system requirements and precautions for when using
Microsoft Windows or Windows Internet Explorer, click “Manual” - “Open” from the supplied
CD-ROM and refer to “Notes on Windows / Internet Explorer versions”.
Trademarks and registered trademarks
•Microsoft, Windows, Windows Media, Internet Explorer, and ActiveX are either registered trademarks or trademarks of Microsoft Corporation in the United States and/or other countries.
•Microsoft product screen shot(s) reprinted with permission from Microsoft Corporation.
• Intel and Intel Core are trademarks of Intel Corporation in the U.S. and other countries.
• Adobe, Acrobat Reader, and Reader are either registered trademarks or trademarks of Adobe
Systems Incorporated in the United States and/or other countries.
• SDXC Logo is a trademark of SD-3C, LLC.
• iPad and iPhone are trademarks of Apple Inc., registered in the U.S. and other countries.
• Android is a trademark of Google Inc.
• Firefox is a registered trademark of the Mozilla Foundation.
• All other trademarks identified herein are the property of their respective owners.
Copyright
Except for open source software licensed under GPL/LGPL and so on, distributing, copying, disassembling, reverse compiling and reverse engineering of the software provided with this product are
all expressly prohibited. In addition, exporting any software provided with this product violating
export laws is prohibited.
7
Open Source Software
•
This product contains open source software licensed under GPL (GNU General Public
License), LGPL (GNU Lesser General Public License), etc.
•
Customers can duplicate, distribute and modify the source code of the software under
license of GPL and/or LGPL.
•Refer to the “readme.txt” file on the provided CD-ROM for further information about open
source software licenses and the source code.
•Please note that Panasonic shall not respond to any inquiries regarding the contents of the
source code.
Network security
As you will use this unit connected to a network, your attention is called to the following security
risks.
① Leakage or theft of information through this unit
② Use of this unit for illegal operations by persons with malicious intent
③ Interference with or stoppage of this unit by persons with malicious intent
It is your responsibility to take precautions such as those described below to protect yourself
against the above network security risks.
• Use this unit in a network secured by a firewall, etc.
• If this unit is connected to a network that includes PCs, make sure that the system is not
infected by computer viruses or other malicious entities (using a regularly updated anti-virus
program, anti-spyware program, etc.).
•To prevent unauthorized access, use user-authentication, set user names and passwords, and
limit which users can log in.
• Apply measures such as user authentication to protect your network against leakage or theft of
information, including image data, authentication information (user names and passwords),
alarm mail information, FTP server information and DDNS server information.
• After the unit is accessed by the administrator, make sure to close the browser.
• Change the administrator password periodically. Additionally, save user authentication information (user names and passwords) in such a way that it is kept out of the hands of third parties.
• Do not install the camera in locations where the camera or the cables can be destroyed or
damaged by persons with malicious intent.
8
Precautions
Do not touch the main unit while this product is panning/ tilting.
Fingers may be caught up in the moving part,
and that may result in injury.
Do not insert any foreign objects.
Fire or electrical shock may be caused if water
or any foreign objects, such as metal objects,
enter inside the unit.
Turn the power off immediately and contact
qualified service personnel for service.
S6130
Do not use this product in an inflammable
atmosphere.
Failure to observe this may cause an explosion
resulting in injury.
Do not place this product in an unstable
place.
Selecting an inappropriate installation surface
may cause this product to fall down or topple
over, resulting in injury or accidents.
Avoid installing this product in the locations where salt damage occurs or corrosive gas is produced.
Otherwise, the mounting portions will deteriorate and accidents such as a fall of the product
may occur.
Do not attempt to disassemble or modify
this product.
Failure to observe this may cause fire or electric
shock.
Consult the dealer for the repair or inspections.
Do not strike or give a strong shock to this
product.
Failure to observe this may cause fire or injury.
Do not install or clean the camera, or
touch this product, the power cable or the
connected cables during thunder storms.
Failure to observe this may cause electric shock.
Keep SDXC/SDHC/SD memory cards
away from infants and children.
Otherwise, they may swallow the cards by mistake.
In this case, consult a doctor immediately.
Refer installation work to the dealer.
Installation work requires technique and experience. Failure to observe this may cause fire,
electric shock, injury, or damage to the product.
Be sure to consult the dealer.
S6130
Stop the operation immediately when
something is wrong with this product.
When smoke goes up from the product, the
smell of smoke comes from the product, or the
exterior of the product has deteriorated, continued use will cause a fire or fall of the product
resulting in injury, or damage to the product.
In this case, turn the power off immediately and
contact qualified service personnel for service.
Do not use tripod screws when installing this
product on the ceiling.
Failure to observe this may cause injury.
Use the exclusively designed mount bracket for
installation.
Do not hang down from this product or
use this product as a pedestal.
Failure to observe this may cause a drop
resulting in accidents.
Select an installation area that can support the total weight.
Selecting an inappropriate installation surface
may cause this product to fall down or topple
over, resulting in injury or accidents.
Installation work shall be started after sufficient
reinforcement.
Do not damage the power cable.
Do not damage, fabricate, twist, stretch, bundle, or
forcibly bend the power cable. Do not place heavy
objects on it, and keep it away from heat sources.
Use of a damaged power cable may cause
electric shock, short circuit, or fire.
Consult the dealer for repair.
9
Periodic inspections shall be conducted.
Rust on the metal parts or screws may cause a
fall of the product resulting in injury or accidents.
Consult the dealer for the inspections.
Do not rub the edges of metal parts with
your hand.
Failure to observe this may cause injury.
[Precautions for use]
The exclusively designed mount bracket
shall be used.
(Except for placing WV-S6130 upside-down)
Failure to observe this may cause a drop
resulting in injury or accidents.
Use the exclusively designed mount bracket for
installation.
When the product is accessible from the
Internet
To prevent unauthorized access, note the following.
• Leave user authentication turned on.
• Periodically change passwords that are
used to access the product.
Refer to the Operating Instructions on the
provided CD-ROM for information about
how to change passwords.
The screws and bolts must be tightened to
the specified torque.
Failure to observe this may cause a drop
resulting in injury or accidents.
To keep on using with stable performance
Do not use this product in hot and humid conditions for a long time. Failure to observe this
causes component degradation resulting in life
shortening of this product. Do not expose this
product to direct heat sources such as a heater.
Turn the power off when do wiring of this
product.
Failure to observe this may cause electric
shock. In addition, short circuit or wrong wiring
may cause fire.
This product is designed to be used indoors.
This product is not operable outdoors.
Install this product in a location high
enough to avoid people and objects from
bumping the product.
Failure to observe this may cause injury.
Make sure that the product does not
become wet.
Keep this camera away from water and moisture.
The measures of protection against a fall
of this product shall be taken.
(Except for placing WV-S6130 upside-down)
Failure to observe this may cause a drop
resulting in injury.
Be sure to install the safety wire.
This product has no power switch.
When turning off the power, disconnect the
power supply from the 12 V DC power supply
or the PoE device.
Handle this product with care.
Do not drop this product, nor apply shock or
vibration to the product. Failure to observe this
may cause trouble.
Do not install this product in locations
subject to vibration.
Loosening of mounting screws or bolts may cause
a fall of the product resulting in injury or accidents.
About the battery
A battery is installed inside the camera. Do not
leave the battery exposed in environments of
excessive heat as a result of sunlight or fire.
Correctly perform all wiring
Short circuits in the wiring or incorrect wiring
may cause fire or electrical shock.
S6131
Turn the power off when cleaning this product.
Failure to observe this may cause injury.
S6111
Do not touch the lens surface with your
bare hands.
A dirty lens surface causes deterioration of picture quality.
10
About the MOS image sensor
• When continuously shooting a bright light
source such as a spotlight, the color filter
of the MOS image sensor may become
deteriorated and this may cause discoloration. Even when changing the fixed
shooting direction after continuously
shooting a spotlight for a certain period,
the discoloration may remain.
• When shooting fast-moving subjects or
objects crossing the shooting area may
look to be bending askew.
S6130
Do not touch the dome cover with your
bare hands.
A dirty dome cover causes deterioration of picture quality.
When an error is detected, this product
will restart automatically.
This product will be inoperable for around 2
minutes after the restart just as when the
power is turned on.
About the automatic status detection
function
When this product malfunctions due to exogenous noise, etc. for 30 seconds or more, the
product will automatically reset and will return to
normal state. When the product is reset, initialization will be carried out as when the power of the
product is turned on. When the product repeatedly resets, exogenous noise level around the
product may be high and that may cause malfunction. Contact your dealer for instructions.
Cleaning this product body
Be sure to turn off the power before cleaning.
Failure to observe this may cause injury. Do not
use benzine, thinner, alcohol, or any other
types of solvents or detergents. Otherwise, it
may cause discoloration. When using a chemical cloth for cleaning, read the caution provided with the chemical cloth product.
* Do not loozen or remove screws unless
instructed to do so in the product documentation.
* The camera position may be moved inadvertently while cleaning the camera body. Restart
the camera or refresh the camera position (position refresh) to correct the camera position.
Refer to the Operating Instructions (included in
the CD-ROM) for further information.
Periodically images on the screen appear
to be distorted
When the camera is installed in a location where
it is subject to small vibrations (for example,
when it is installed near devices that vibrate),
images may appear distorted and stretched
lengthways. This phenomenon is a characteristic of image pickup devices that use MOS sensors and is caused by the relationship between
the periodic movements of the camera and the
timing that the image sensor reads images. This
is not a problem with the camera. To reduce the
possibility of this phenomenon occurring, install
the camera in a secure location.
S6131
S6111
Cleaning the lens
Use a lens cleaning paper (used to clean camera lenses or lenses of spectacles). When using
solvent, use an alcohols solvent and do not
use a thinner or a glass cleaner.
S6130
Cleaning of the dome cover
Use lens cleaning paper (used to clean camera
or spectacles lenses) to remove any dirt on the
dome cover.
We shall not be liable for content
compensation, losses of recorded or
edited content and any direct or indirect
consequent damages caused by failure to
record or edit due to faults with this unit or
the SD memory card. In addition, the same
provisions apply after unit is reparied.
About the stabilizer function
Depending on the conditions in the installation
area, effects of the stabilizer function may not
be fully achieved.
11
Consumable parts
The following are consumables: Replace them
in accordance with their operating lifetimes.
Their operating lifetimes vary depending on the
usage environment and conditions. The operating lifetimes below are just guides for when
using the camera at +35 °C {95 °F}.
S6131
Lens and pan/tilt head
If a lens and pan/tilt head are not performed for
a long period of time, the grease coating inside
these parts may become sticky. That may
obstruct the parts from moving. To prevent
this, move the lens or pan/tilt head periodically.
Or perform position refresh.
S6111
Position refresh
During the use for a long period of time, the preset positions may become inaccurate. When
“Position refresh” is set for the created schedule,
the camera position will be corrected periodically.
Refer to the Operating Instructions on the provided CD-ROM for how to perform the settings.
• Lens unit, panning motor, tilting motor, flat
cable for tilting, slip ring: Approx. 3.7 million operations (Approx. 20000 hours)
* When continuing the action of moving the set
position for a long period, dust may accumulate
on a slip ring. It can be prevented by executing
the position refresh action regularly (about once
a week) using the schedule setting.
Equipment classification and power
source indication label
Refer to the indication label on the bottom side
of this unit for the equipment classification,
power source, and other information.
S6130
• Lens unit, panning motor, tilting motor, flat
cable for panning, flat cable for tilting:
Approx. 3.7 million operations (Approx.
20000 hours)
Product disposal/transfer
Data saved on this product or a storage device
used with this product may lead to personal
information leakage. When it is necessary to
dispose or give this product to someone, even
when for repair, make sure that there is no data
on this product.
When abandoning the memory media, it is recommended to destroy it physically after deleting data by PC.
Do not hold the dome section.
The dome section of this unit rotates. When
removing this unit from a ceiling or wall, turn
the unit while holding the fixed section.
Motor operating sound
The operating sound may be louder depending
on the speed of panning/tilting operations.
When you feel uneasy, the operating sound
can be diminished by reducing the setting
value of auto panning speed.
Meaning of symbols
: Direct current symbol
AVC Patent Portfolio License
THIS PRODUCT IS LICENSED UNDER THE AVC
PATENT PORTFOLIO LICENSE FOR THE PERSONAL USE OF A CONSUMER OR OTHER USES
IN WHICH IT DOES NOT RECEIVE REMUNERATION TO (i) ENCODE VIDEO IN COMPLIANCE WITH
THE AVC STANDARD (“AVC VIDEO”) AND/OR (ii)
DECODE AVC VIDEO THAT WAS ENCODED BY A
CONSUMER ENGAGED IN A PERSONAL ACTIVITY
AND/OR WAS OBTAINED FROM A VIDEO PROVIDER LICENSED TO PROVIDE AVC VIDEO. NO
LICENSE IS GRANTED OR SHALL BE IMPLIED
FOR ANY OTHER USE. ADDITIONAL INFORMATION MAY BE OBTAINED FROM MPEG LA, L.L.C.
SEE HTTP://WWW.MPEGLA.COM
S6130
: Hot surface symbol
12
Precautions for installation
Panasonic assumes no responsibility for injuries or property damage resulting from failures
arising out of improper installation or operation inconsistent with this documentation.
For information about the installation tasks, refer to the provided Installation Guide.
In order to prevent injury, the product
must be securely mounted to a wall or
ceiling according to Installation Guide.
(Except for placing WV-S6130 upside-down)
S6130
• When hanging the camera from a ceiling,
use the WV-Q105A and WV-Q160C/
WV-Q160S ceiling mount bracket (option)
or the WV-Q159C/WV-Q159S ceiling
embedding bracket (option).
• When installing on a wall, use wall mount
bracket WV-Q158C/WV-Q158S (option).
Power supply
This product has no power switch.
When performing electrical work, make sure the
camera can be turned on and off. When an
Ethernet cable or power cable is connected, the
power is turned on. When the power is supplied, the product will perform panning, tilting,
zooming and focusing. When cleaning the product, remove the Ethernet cable or disconnect
the power cable from the main power supply.
This camera is designed to be used indoors.
This product is not operable outdoors.
Do not expose this camera to direct sunlight
for hours and do not install the product near a
heater or an air conditioner. Otherwise, it may
cause deformation, discoloration and malfunction. Keep this camera away from water and
moisture.
Installation area for this product
Select an appropriate place for the installation
area (such as a strong wall or ceiling) in your
particular environment.
• Make sure that the installation area is
strong enough to hold this product, such
as a concrete ceiling.
• Install the camera in the foundation area of
the architecture or where sufficient strength
is assured.
• Do not mount the product on a plaster
board or a wooden section because they
are too weak. If the product is unavoidably
mounted on such a section, the section
shall be sufficiently reinforced.
In addition to fitting the camera into a ceiling
directly using the camera mount bracket
(accessory), the camera can be installed using
the special brackets as follows.
S6131
Do not place this product in the following
places:
• Locations where a chemical agent is used
such as a swimming pool
• Locations subject to moisture or oil smoke
such as a kitchen
• Locations that have a specific environment
that is subject to an inflammable atmosphere or solvents
• Locations where a radiation, an X-ray, a
strong radio wave or a strong magnetic
field is generated
• Locations near coasts directly subjected to
sea breezes, or locations subject to corrosive gases such as from hot springs, volcanic regions, etc.
• Locations where the temperature is not
within the specified range (☞ page 30)
• Locations subject to vibrations, such as on
vehicles, marine vessels, or above product
lines (This product is not designed for onvehicle use.)
• Locations where it may get wet from rain or
water splash (including under the eaves, etc.)
S6111
• When hanging the camera from a ceiling,
use the WV-Q105A ceiling mount bracket
(option) or the WV-Q126A ceiling embedding bracket (option).
• When installing on a wall, use wall mount
bracket WV-Q119 (option).
13
When noise disturbance may happen
Conduct the power distribution work to keep a
distance of 1 m {3.28 feet} or more from the
120 V (for U.S. and Canada) or 220 V – 240 V
(for Europe and other countries) power line. Or
conduct the electric conduit work separately
(Always connect the metal pipe with grounding).
• Locations subject to moisture or dust
• Locations subject to condensation as the
result of severe changes in temperature
S6131
S6111
Mounting method for this product
This product is designed to be used as a pendant mount camera. If the product is mounted
on a desktop or at a slant, it may not work correctly and its lifetime may be shortened.
Radio disturbance
Noise may appear in video or audio near a
strong electric field from a TV or radio antenna,
motors and transformers, or a strong electric
field/magnetic field from a power line (lamp line)
of AC100 V or more.
Sulfurization caused by rubber products
Do not place the product near rubber products
(packing, rubber feet, etc.) that contain sulfur.
There is a risk that sulfur components in rubber
products may cause electrical parts and terminals, etc. to become sulfurized and corrode.
PoE (Power over Ethernet)
Use a PoE hub/device that is compliant with
IEEE802.3af standard.
Screw tightening
• The screws and bolts must be tightened
with an appropriate tightening torque
according to the material and strength of
the installation area.
• Do not use an impact driver. Use of an
impact driver may damage the screws or
cause tightening excessively.
• When a screw is tightened, make the
screw at a right angle to the surface. After
tightening the screws or bolts, perform
checks to ensure that the tightening is
sufficient enough so that there is no
movement or looseness.
S6131
Router
When connecting this product to the Internet,
use a broadband router with the port forwarding function (NAT, IP masquerade).
Refer to the Operating Instructions on the provided CD-ROM for further information about
the port forwarding function.
Time & date setting
It is necessary to set the time & date before
putting this product into operation. Refer to the
Operating Instructions on the provided
CD-ROM for descriptions of how to perform
the settings.
S6111
Make sure to remove this product if it will
no longer be used.
Protective caps
The protective caps are used to prevent dirt
and dust from entering inside this product.
Keep the protective caps inserted in connectors that are not used.
Protection from lightning
When cables are used outdoors, there is a
chance that they may be affected by lightning.
In such a case, install a lightning arrestor close
to the camera, and make the length of the network cable between the camera and lightning
arrestor as short as possible to prevent the
camera from being damaged by lightning.
14
Parts and functions
【Whole unit】
S6131
S6130
S6111
Camera mount
bracket (accessory)
OP
EN
LO
CK
FRONT
Safety wire
(fixed with the
mount bracket)
Decorative cover
(accessory)
Decorative cover upper part
(accessory)
LOCK
OPEN
130
-S6
WV
Decorative cover lower part
(accessory)
Status
indicator
Dome cover
【Front view】
S6131
S6130
S6111
SD memory card cover
Fixed section
Panasonic
logo plate
Two-dimensional
barcode (Data Matrix):
To our website*1
Dome section
*1 Depending on the scanning application used, the Data Matrix may not be able to be
read correctly. In this case, access the site by directly entering the following URL.
https://security.panasonic.com/support/qr_sp_select/
15
【Bottom view】
S6130
Tripod screw hole
(1/4-20 UNC for tripod: Depth 6 mm {1/4 inches})
IMPORTANT:
•• Use the tripod screw hole only when
installing the camera upside-down on a
desk top with a camera tripod.
•• Do not use a tripod screw to mount the
camera on the ceiling since the fall prevention measure is unavailable.
Note: S6130
The direction of Panasonic logo plate can be
changed.
①Push “P” on the right of the Panasonic logo
plate (refer to the illustration of【Front view】
in Parts and functions) to unlock and pull it
out.
②Pull the Panasonic logo plate out a little
and rotate it by 180°.
③Push the Panasonic logo plate to lock it
again.
①
②
16
【Rear view】 ■ Terminals
S6131
S6111
②12 V DC power supply terminal
③Audio input connector
⑤EXT I/O terminals
④Audio output connector
①Network connector
Safety wire holder
S6130
②12 V DC power supply terminal
INITIAL SET button
③Audio input connector
⑤EXT I/O terminals
④Audio output connector
⑥Monitor out
connector
①Network connector
Safety wire holder
①Network connector (RJ45)
Connect an Ethernet cable (category 5e or better) to the network connector.
IMPORTANT:
•• Use all 4 pairs (8 pins) of the Ethernet cable.
•• The maximum length of the Ethernet cable (locally procured) is 100 m.
•• Make sure that the PoE device in use is compliant with IEEE802.3af standard.
•• When connecting both the 12 V DC power supply and the PoE device for power supply, 12 V
DC will be used for power supply.
•• When the Ethernet cable is disconnected once, reconnect the cable after around 2 seconds.
When the cable is quickly reconnected, the power may not be supplied from the PoE device.
17
②12 V DC power supply terminal
Caution:
•• A READILY ACCESSIBLE DISCONNECT DEVICE SHALL BE INCORPORATED TO THE
EQUIPMENT POWERED BY 12 V DC POWER SUPPLY.
•• ONLY CONNECT 12 V DC CLASS 2 POWER SUPPLY (UL 1310/CSA 223) or LIMITED
POWER SOURCE (IEC/EN/UL/CSA 60950-1).
Connect the output cable of the DC power supply to the power cable plug (accessory).
IMPORTANT:
•• Be sure to use the power cable plug (accessory) provided with this product.
•• Be sure to fully insert the power cable plug (accessory) into the 12 V DC power supply
terminal. Otherwise, it may damage the camera or cause malfunction.
•• When installing the camera, make sure that excessive force is not applied to the power cable.
•• Be sure to use an AC adaptor compliant with the specifications (written in the indication label
on the bottom side of this unit) regarding power source and power consumption.
③Audio input connector
Connect a microphone or the line out of an external device using a ø3.5 mm stereo mini plug
(monaural input S6131
/ stereo input S6130 ).
S6111
•• Input impedance
: Approx. 2 kΩ (unbalanced)
•• Recommended cable length
: Less than 1 m {3.28 feet} (for microphone input)
Less than 10 m {32.8 feet} (for line input)
•• Recommended microphone
: Plug-in power type (locally procured)
(Sensitivity of microphone
: –48 dB ±3 dB (0 dB=1 V/Pa,1 kHz))
S6111
•• Supply voltage
: 4.0 V±0.5 V S6131
2.5 V±0.5 V S6130
•• Input level for the line input
: Approx. –10 dBV
④Audio output connector
Connect an external speaker* using a ø3.5 mm stereo mini plug (monaural output S6131
S6111 /
stereo output S6130 ).
•• Output impedance
: Approx. 600 Ω (unbalanced)
•• Recommended cable length
: Less than 10 m {32.8 feet}
*Use a powered speaker.
•• Output level
: –20 dBV
Note: S6131
S6111
•• The audio output can be switched to the monitor output. Refer to the "Operating Instructions"
on the provided CD-ROM for descriptions of how to switch the output.
•• The monitor out is set to NTSC in the default settings of the camera. If you want to change the
monitor out setting to PAL, refer to the Operating Instructions on the provided CD-ROM.
IMPORTANT:
•• Connect/disconnect the audio cables and turn on the power of the camera after turning off
the power of the audio output devices. Otherwise, loud noise may be heard from the speaker.
•• Make sure that the stereo mini plug is connected to this cable. When a monaural mini plug is
connected, audio may not be heard.
When connecting a monaural speaker with amplifier, use a locally procured conversion cable
(mono-stereo).
18
⑤EXT I/O terminals
Connect an external device to the external I/O terminal and fit it into the camera.
Note:
•• Off, input, and output of the external I/O terminal 2 and 3 can be switched by configuring the
setting. Refer to the Operating Instructions on the provided CD-ROM for further information
about the EXT I/O terminal 2 and 3 (ALARM IN2, 3) settings ("Off", "Alarm input", "Alarm output" or "AUX output").
<Ratings>
•• ALARM IN1 (Black & white input, Auto time adjustment input), ALARM IN2, ALARM IN3
Input specification : No-voltage make contact input (4 V - 5 V DC, internally pulled up)
OFF
: Open or 4 V - 5 V DC
ON
: Make contact with GND (required drive current: 1 mA or more)
•• ALARM OUT, AUX OUT
Output specification: Open collector output (maximum applied voltage: 20 V DC)
ON
: 4 V - 5 V DC by internal pull-up
OFF
: Output voltage 1 V DC or less (maximum drive current: 50 mA)
External I/O terminal
4 3 2 1
GND
ALARM IN3 (Terminal 3)
(Alarm input / AUX output)
ALARM IN2 (Terminal 2)
(Alarm input / Alarm output)
ALARM IN1 (Terminal 1)
(Alarm input / Black & white input / Auto time adjustment input)
Button
IMPORTANT:
•• Install external devices so that they do not exceed the rating of the network camera.
•• When using the EXT I/O terminals as the output terminals, ensure they do not cause signal
collision with external signals.
S6130
⑥MONITOR OUT connector (factory shipment: NTSC monitor)
Used to connect a monitor used for confirmation when performing service.
Note:
•• The monitor out is set to NTSC in the default settings of the camera. If you want to change the
monitor out setting to PAL, refer to the Operating Instructions on the provided CD-ROM.
IMPORTANT:
•• The confirmation monitor is used for checking the angular field of view when servicing. It is
not provided for recording/monitoring use.
•• Depending on the monitor, some characters (camera title, preset ID, etc.) may not be displayed on the screen.
19
When connecting to a network using a PoE hub
Before starting the installation, check the entire system configuration. The following illustration gives
a wiring example of how to connect the camera to the network via a PoE device (hub).
Confirmation
Powered speaker
monitor
PoE device (hub)
Ethernet cable
(category 5e or better,
straight)
Ethernet cable
(category 5e or
better, straight)
Microphone
Powered speaker
Microphone
LOCK
PC
OPEN
130
-S6
WV
Ethernet cable
(category 5e or better,
straight)
Confirmation
monitor
* Use an Ethernet cable (category
5e or better, cross) when directly
connecting the camera to a PC.
IMPORTANT:
•• Use a switching hub or a router which is compliant with 10BASE-T/100BASE-TX.
•• If a PoE hub is not used, each network camera must be connected to a 12 V DC power
supply.
•• When using 12 V DC, power supply from a PoE hub or router is not required.
20
■ Indicators and buttons
S6131
S6111
<Inside of the memory card cover>
SD memory card cover
②SD MOUNT indicator
①INITIAL SET button
④SD ON/OFF button
SD memory card slot (SD)
<Connection terminals on the back>
③STATUS indicator
21
■ Indicators and buttons (continued)
S6130
<Inside of the memory card cover>
SD memory card cover
④SD ON/OFF button
②SD MOUNT indicator
SD memory card slot (SD)
<Connection terminals on the back>
①INITIAL SET button
<Whole unit>
LOCK
OPEN
③Status indicator
22
①INITIAL SET button (Initializing button)
Follow the steps below to initialize the network camera.
⑴Turn off the power of the camera. When using a PoE hub, disconnect the Ethernet cable from
the camera. When using an external power supply, disconnect the power cable plug (accessory)
from the 12 V DC power supply terminal.
⑵Turn on the power of the camera while pressing the INITIAL SET button, and make sure to
release the button after approximately 15 seconds. In about 2 minutes later, the camera will start
up and the settings including the network settings will be initialized. Retry if the camera does not
start up normally.
IMPORTANT:
•• When the camera is initialized, the settings including the network settings will be initialized.
Before initializing the settings, it is recommended to write down the settings in advance.
•• Do not turn off the power of the camera during the process of initialization. Otherwise, it may
fail to initialize and may cause malfunction.
②SD MOUNT indicator
SD memory card status
SD MOUNT indicator status
When an SD memory card is inserted and could be
recognized
Lights off → Blinks green →
Lights off
When an unformatted SD memory card is inserted and
formatted on the setup menu
Lights off (When inserted/formatting)
→ Blinks green → Lights green
When the SD memory card in use is formatted on the
setup menu
Lights green → Lights off (Formatting)
→ Blinks green → Lights green
When data can be saved after the SD memory card is
inserted and the SD ON/OFF button is pressed (less than
1 second)
Lights off → Lights green
When data can be saved to the SD memory card
Lights green
When the SD memory card is removed
after holding down the SD ON/OFF button
(about 2 seconds)
(recording)
Lights green → Blinks green →
Lights off
(waiting for
recording)
Lights green → Lights off
When data cannot be saved to the SD memory card
because an abnormality was detected or the SD memory
card is configured not to be used
23
Lights off
③Status indicator
Operation status
Indicator status
When the power Before the network connection Lights orange → Lights off → Blinks orange →
is turned on
is established
Lights orange
When the network connection Lights orange → Lights off → Blinks orange →
is established
Blinks green → Lights green
During the standby Cable is not connected
or connection
Cable is connected
Lights orange
During the upgrade process
Blinks orange
Initialization (When the network connection is
established)
Lights orange → Lights off → Blinks orange →
Lights orange → Blinks orange → Blinks green
→ Lights green
Lights green
Port forwarding error caused by the UPnP function Blinks orange (in 2 seconds intervals
(on for 1 second / off for 1 second))
Trouble happening on the camera
Blinks red
Failure in writing data on the SD memory card
Lights red
Note:
•• Lighting/blinking LED can be turned off with the software settings at any time. (The initial state
is lighting or blinking.) Set the LED to be solid off if necessary, depending on the installation
conditions. (☞ Operating instructions included in the CD-ROM)
•• When the power is on, initialization may start with orange blinking.
④SD ON/OFF button
⑴When the SD ON/OFF button is pressed (less than 1 second), the SD MOUNT indicator lights
up in green and data can be saved to the SD memory card.
⑵When the SD ON/OFF button is held down (about 2 seconds), the SD MOUNT indicator lights
off and the SD memory card can be removed.
24
Insert / remove an SD memory card
■ Insert an SD memory card
S6131
S6111
SD memory card cover
➀Slide the SD memory card cover to the arrow
direction to open the cover
➁Insert an SD memory card fully into the SD
memory card slot, and then push the memory
card straight into the slot until a click is heard
•• Insert the SD memory card with the label facing the
bottom side of the camera until it makes a clicking
sound.
•• After the SD memory card has been inserted, press the
SD ON/OFF button with a tip of the ball point pen, and
make sure the SD MOUNT indicator is connubially lit.
•• If you do not press the SD ON/OFF button after inserting the SD memory card, the SD MOUNT indicator is
automatically lit approximately 5 minutes later.
➂Shut the SD memory card cover
SD MOUNT indicator
SD ON/OFF button
Bottom side
* Label facing
bottom side
SD memory card slot (SD)
S6130
➀Place the camera upside-down, push the left of the Panasonic logo plate on the front
panel to unlock the SD memory card cover, and pull it out a little.
➁Slide the SD memory card cover to the arrow direction to open the cover
➀
➁
Panasonic
logo plate
SD memory card cover
25
➂Insert an SD memory card fully into the SD
memory card slot, and then push the memory card straight into the slot until a click
is heard
•• Insert the SD memory card with its label facing
the bottom side of the camera and its back end
at the same height as the right and left SD
guide ribs until it makes a clicking sound.
•• Take your fingers off the SD memory card and
check that its back end does not protrude over
the SD guide ribs (on the both sides of the SD
memory card slot).
•• After the SD memory card has been inserted,
press the SD ON/OFF button,and make sure
the SD MOUNT indicator is continually lit.
•• If you do not press the SD ON/OFF button after
inserting the SD memory card, the SD MOUNT
indicator is automatically lit approximately 5
minutes later.
➃Shut the SD memory card cover
➄Lock the cover by pushing the Panasonic
logo plate
* Label facing bottom side
Label side
Bottom side
SD guide rib
SD memory card slot (SD)
■ Remove an SD memory card
When removing an SD memory card, open the SD memory card cover again and reverse the procedures.
•• To remove the SD memory card, hold down the SD ON/OFF button for about 2 seconds. When the
flashing SD MOUNT indicator goes out, you can remove the SD memory card.
IMPORTANT:
•• Before turning off the camera power, make sure that the SD MOUNT indicator is turned off. If
you turn off the camera power while the SD MOUNT indicator is lit or flashing, the recorded
data may be corrupted or damaged.
Note:
•• Refer to the Operating Instructions on the provided CD-ROM for further information about the
SD memory card settings.
•• When using an SD memory card, format it using this product. Recorded data on the SD memory card will be deleted when formatted. If an unformatted SD memory card or an SD memory
card formatted with other devices is used, this product may not work properly or performance
deterioration may be caused. Refer to the Operating Instructions on the provided CD-ROM for
how to format an SD memory card.
•• When some SD memory cards are used with this product, the product may not work properly or
performance deterioration may be caused. Use the compatible SD memory cards. (☞ page 35)
26
Troubleshooting
Before asking for repairs, check the symptoms with the following table.
Contact your dealer if a problem cannot be solved even after checking and trying the solution in the
table or a problem is not described below.
Symptom
Power is not turned
on.
Cause/solution
When using a PoE device for power supply
•Are the PoE (IEEE802.3af compliant) device and the camera connected with an Ethernet cable?
Check whether the connection is appropriately established.
•Depending on the PoE device, the power supply will
stop when the demanded power exceeds its total
power limit for all PoE ports.
Refer to the operating instructions of the PoE device in
use.
Reference
pages
Installation
Guide
When using DC power supply
• Is the AC adaptor in use compliant with the specifications?
Check the specifications regarding AC adaptor.
•Is the power cable plug inserted to the camera firmly?
Check if it is attached correctly and firmly.
•When the preset positions become inaccurate during
use, it is possible to correct the positions by executing
Operating
the position refresh function.
The camera does not
Instructions
In addition, when “Position refresh” is set for the cremove to the preset
(included in
ated schedule, the camera position will be corrected
positions accurately.
the CD-ROM)
periodically. In some situations, reconfigure the preset
positions.
•The camera position may have become inaccurate.
When the camera is
Carry out the refresh position function from the [Default
panning/tilting, the
Operating
reset] tab of the “Maintenance” page of the setup
camera stops
Instructions
menu.
panning/tilting and
(included in
mechanical noise
the CD-ROM)
comes from the
camera.
•This may be caused by noise.
11
Check the exogenous noise level around the camera.
S6131
The camera starts
panning unpredictably.
S6111
•The protection circuit against high temperature may
function.
When the digital flip (function to turn the screen upsidedown when tilting exceeds a certain angle) continues for
a given time in high temperature, the system releases
the digital flip and operates panning and tilting automatically to return the screen to the original position.
27
−
Symptom
S6130
When using an
optional inner cover,
upper side of images
are hidden (become
black) when the tilt
angle of the camera
is almost level.
Cause/solution
The inner cover (accessory of the optional bracket) is
used to make the silver camera body inconspicuous
through the dome cover when the camera is installed
with the bracket (option).
•This is not malfunction. This is caused by the shape of
the inner cover.
Also, if the setting of “Maximum gain” is too large, the
image will become white depending on the subject.
Reference
pages
−
•Is the Ethernet cable connected appropriately?
Connect the Ethernet cable appropriately.
•Is the hub or router connected to the camera operating
17
appropriately?
Check if the hub or router in use is operating appropriately.
•Isn’t the Ethernet cable connected to the camera broken?
Replace the cable with another one.
• UPnPTM error has occurred since the power is not supplied to the router.
−
Turn on the power of the router. Wait until the connections are established.
•An error has occurred during the port update by the
Status indicator
Operating
UPnP function.
keeps on blinking
If the router in use does not support the UPnP function, Instructions
orange approx. in 2
(included in
perform the port forwarding setting for the router. In
seconds intervals.
addition, deactivate the setting of auto port forwarding the CD-ROM)
for the camera.
•UPnP function of the router is disabled.
Refer to the operating instructions of the router to
−
enable the UPnP function.
•Is “Off” selected for “Indicator” on the “Basic” page?
Operating
Select “On” or “On(Access)” for the indicator setting.
Instructions
Status indicator
(included in
never lights up.
the CD-ROM)
•The camera may be out of order.
Contact your dealer.
•Refer to the [Status information] on the Panasonic supStatus indicator
−
port website (https://security.panasonic.com/support/
keeps on blinking red.
info/) after checking the displayed contents of the
"Maintenance" page - the [Status] tab - [Self check] of
the setup menu.
When the power is
turned on, the status
indicator lights or
blinks orange.
28
Symptom
Status indicator
lights red.
Audio input contains
noise.
The image refresh
interval on the web
browser is longer or
the image is displayed intermittently.
Cause/solution
Reference
pages
This indicator lights up red when data cannot be
saved on the SD memory card.
•Isn’t the write protect switch of the inserted SD memory card set to “LOCK”?
Unlock the write protect switch of the SD memory card.
•Hasn’t the inserted SD memory card been formatted
Operating
on a PC?
Instructions
Use an SD memory card formatted on the camera.
(included in
Or install the software to format the SD memory card
the CD-ROM)
on the PC.
Refer to our website
(https://security.panasonic.com/support/info/) for further information about the supported software.
•Isn’t the inserted SD memory card faulty?
Replace the card with a normal one.
•Check the following.
• Grounding of the camera, a switching hub or peripheral devices are not done.
• The camera is used near an electrical power line.
• The camera is used near a device which produces
14
strong magnetic field or radio waves (such as near a
TV/radio antenna, a motor of an air conditioning system, a transformer, etc.)
When audio input still contains noise even after checking the above possibilities, use a powered microphone
or connect audio output with low output impedance.
•When using the camera with the high frame rate and
high image quality, the image update delays due to the
PC specifications. These cases may be improved by
using a PC with the following specifications.
CPU: Intel® CoreTM i7 6700 or faster
Memory: 8 GB dual channel (4 GB×2) or more
【Example of using the camera in case that the image
6
refresh interval is longer or intermittent】
• Image capture size: 1920×1080, Frame rate: 60 fps,
Bit rate: 4096 kbps S6130
S6131
• Image capture size: 1280×720, Frame rate: 60 fps,
Bit rate: 3072 kbps
• Image capture size: 1280×720, Frame rate: 30 fps,
Bit rate: 2048 kbps
(When referring to multiple browsers 4 images or more)
29
Specifications
• Basic
WV-S6131 / WV-S6111
Power source *1:
Power consumption *1:
WV-S6130
DC 12 V
PoE (IEEE802.3af compliant)
DC 12 V
: 1 A/12 W
PoE DC 48 V: 250 mA/12 W (Class 0 device)
Operating environment
Ambient operating temperature: –10 °C to +50 °C {14 °F to 122 °F} Ceiling/ Place the camera
upside-down *2
–10 °C to +50 °C {14 °F to 122 °F}
Desktop/ Tripod
–10 °C to +40 °C {14 °F to 104 °F}
Ambient operating humidity: 10 % to 90 % (no condensation) 10 % to 90 % (no condensation)
Storage environment
Storage temperature: –30 °C to +60 °C {–22 °F to 140 °F}
Storage humidity: 10 % to 95 % (no condensation)
None
VBS: 1
.0 V [p-p]/75 Ω, composMonitor output
ite, ø3.5 mm mini jack
(for confirmation):
External I/O terminals:
ALARM IN 1 (Black & white input, Auto time adjustment input) (x1)
ALARM IN 2 (ALARM OUT) (x1)
ALARM IN 3 (AUX OUT) (x1)
Audio input:
ø3.5 mm stereo mini jack
ø3.5 mm stereo mini jack
(Monaural input)
(Stereo input)
Input impedance:
For microphone input: Input impedance:
Approx. 2 kΩ (unbalanced)
Approx. 2 kΩ (unbalanced)
Recommended applicable micro- Recommended applicable microphone: Plug-in power type
phone: Plug-in power type
(Sensitivity of microphone:
(Sensitivity of microphone:
-48 dB±3 dB
-48 dB±3 dB
(0 dB=1 V/Pa, 1 kHz))
(0 dB=1 V/Pa, 1 kHz))
Supply voltage: 2.5 V ±0.5 V
Supply voltage: 4.0 V ±0.5 V
For line input: Input level: Approx. –10 dBV
Input level: Approx. –10 dBV
Audio output:
ø3.5 mm stereo mini jack
ø3.5 mm stereo mini jack
(Monaural output) *3
(Stereo output)
Output impedance:
Output impedance:
Approx. 600 Ω (unbalanced) Approx. 600 Ω (unbalanced)
Output level: –20 dBV
Output level: –20 dBV
Dimensions:
ø185 mm × 214 mm (H)
Including the decorative cover
{ø7-9/32 inches × 8-7/16 inches (H)} ø185 mm × 157 mm (H)
(including the decorative covers) {ø7-9/32 inches × 6-3/16 inches (H)}
Excluding the decorative cover
(place the camera upside-down)
ø115 mm × 155 mm (H)
{ø4-17/32 inches × 6-3/32 inches (H)}
30
Mass:
Finish:
WV-S6131 / WV-S6111
WV-S6130
Main body:
Approx. 1.74 kg {3.84 lbs}
Including camera mount bracket,
decorative cover:
Approx. 240 g {0.53 lbs}
Camera:ABS resin Black
Decorative cover:
ABS resin (Sail white)
Main body:
Approx. 1.1 kg {2.43 lbs}
Including camera mount bracket,
decorative cover:
Approx. 200 g {0.44 lbs}
Camera:PC+ABS resin
Fine silver
Dome: PMMA resin Clear
Decorative cover:
PC+ABS resin
Fine silver
*1 Refer to our website (https://security.panasonic.com/support/info/) for further information about
Power source and Power consumption information.
*2 The camera is fixed on the camera mount bracket (accessory).
*3 The audio output can be switched to the monitor output. Refer to the "Operating Instructions"
on the provided CD-ROM for descriptions of how to switch the output.
• Camera
Image sensor:
Effective pixels:
Scanning area:
Scanning system:
Minimum illumination:
WV-S6131 / WV-S6111
WV-S6130
1/2.8 type MOS image sensor
Approx. 2.1 mega pixels
5.57 mm (H) × 3.13 mm (V)
{7/32 inches (H) × 1/8 inches (V)}
Progressive
1/2.9 type MOS image sensor
Approx. 2.4 mega pixels
5.28 mm (H) × 2.97 mm (V)
{7/32 inches (H) × 1/8 inches (V)}
S6131
Color:0.015 lx {0.00139 footcandle}
(F1.6, Maximum shutter: Off (1/30 s), AGC: 11)
0.001 lx {0.00009 footcandle}
(F1.6, Maximum shutter: max. 16/30 s, AGC: 11)*
BW :0.006 lx {0.00056 footcandle}
(F1.6, Maximum shutter: Off (1/30 s), AGC: 11)
0.0004 lx {0.00004 footcandle}
(F1.6, Maximum shutter: max. 16/30 s, AGC: 11)*
S6111
Color:0.011 lx {0.00102 footcandle}
(F1.6, Maximum shutter: Off (1/30 s), AGC: 11)
0.0007 lx {0.00007 footcandle}
(F1.6, Maximum shutter: max. 16/30 s, AGC: 11)*
BW :0.005 lx {0.00046 footcandle}
(F1.6, Maximum shutter: Off (1/30 s), AGC: 11)
0.0003 lx {0.00003 footcandle}
(F1.6, Maximum shutter: max. 16/30 s, AGC: 11)*
31
WV-S6131 / WV-S6111
Minimum illumination:
WV-S6130
S6130
Color:0.015 lx {0.00139 footcandle}
(F1.6, Maximum shutter: Off (1/30 s), AGC: 11)
0.001 lx {0.00009 footcandle}
(F1.6, Maximum shutter: max. 16/30 s, AGC: 11)*
BW :0.006 lx {0.00056 footcandle}
(F1.6, Maximum shutter: Off (1/30 s), AGC: 11)
0.0004 lx {0.00004 footcandle}
(F1.6, Maximum shutter: max. 16/30 s, AGC: 11)*
* Converted value
Intelligent auto
On/ Off
Super Dynamic:
On/ Off, the level can be set in the range of 0 to 31.
* When 60 fps is selected, the Super Dynamic function is automatically set to off.
Dynamic range:
144 dB typ. (Super Dynamic: On)
Maximum gain (AGC):
The level can be set in the range of 0 to 11.
Auto contrast adjust:
On/ Off
Adaptive black stretch:
The level can be set in the range of 0 to 255.
Back light compensation
BLC/ HLC/ Off
(BLC) /High light compensa- (only when Super Dynamic/ Intelligent auto: Off)
tion (HLC):
Fog compensation:
On/ Off (only when Intelligent auto/ auto contrast adjust: Off)
Light control mode setting: Outdoor scene/ Indoor scene (50 Hz)/ Indoor scene (60 Hz)/
Fix shutter
Shutter speed:
1/30 Fix, 3/120 Fix, 2/100 Fix, 2/120 Fix, 1/60 Fix, 1/100 Fix,
1/120 Fix, 1/250 Fix, 1/500 Fix, 1/1000 Fix, 1/2000 Fix, 1/4000 Fix,
1/10000 Fix
*1/30 Fix to 2/120 Fix is available during 30 fps mode only.
*1/60 Fix is available during 60 fps mode only.
Maximum shutter:
Max.1/4000 s, Max.1/2000 s, Max.1/1000 s, Max.1/500 s,
Max.1/250 s, Max.1/120 s, Max.1/100 s, Max.2/120 s, Max.2/100 s,
Max.3/120 s, Max.1/30 s, Max.2/30 s, Max.4/30 s, Max.6/30 s,
Max.10/30 s, Max.16/30 s
*Max.2/100 s and Max.3/120 s are available during 30 fps mode only.
Color/BW:
Off/ On/ Auto1(Normal)/ Auto2(IR Light)/ Auto3(SCC)
White balance:
ATW1/ ATW2/ AWC
Digital noise reduction:
The level can be set in the range of 0 to 255.
Stabilizer
On/ Off (Available only set to the 30 fps mode)
Privacy zone:
Filling/ Pixelate/ Off (up to 32 zones available)
Camera title on screen:
On/ Off
Up to 20 characters (alphanumeric characters, marks)
Video Motion Detection (VMD): On/ Off, 4 areas available
32
• Lens
WV-S6131 / WV-S6111
WV-S6130
40x Optical zoom
60x with HD Extra Optical Zoom *1
(Motorized zoom / Motorized focus)
16x (Max 640x)
21x Optical zoom
31x with HD Extra Optical Zoom *1
(Motorized zoom / Motorized focus)
16x (Max 336x)
Focal length:
4.25 mm – 170 mm
{5/32 inches – 6-11/16 inches}
4.0 mm – 84.6 mm
{5/32 inches – 3-11/32 inches}
Maximum aperture ratio:
1:1.6 (WIDE) – 1:4.95 (TELE)
1:1.6 (WIDE) – 1:4.5 (TELE)
Focus range:
3 m {9 ft 10-1/8 inches} – ∞
1.5 m {4 ft 11-1/16 inches} – ∞
Aperture range:
F1.6 – CLOSE
Angular field of view:
[16:9 mode]
Horizontal:1.9 ° (TELE) – 66 ° (WIDE)
Vertical: 1.1 ° (TELE) – 39 ° (WIDE)
[4:3 mode]
Horizontal: 1.4 ° (TELE) – 51 ° (WIDE)
Vertical: 1.1 ° (TELE) – 39 ° (WIDE)
[16:9 mode]
Horizontal:3.5 ° (TELE) – 74 ° (WIDE)
Vertical: 2.0 ° (TELE) – 42 ° (WIDE)
[4:3 mode]
Horizontal: 3.0 ° (TELE) – 61 ° (WIDE)
Vertical: 2.3 ° (TELE) – 46 ° (WIDE)
WV-S6131 / WV-S6111
WV-S6130
Zoom ratio:
Digital (electronic) zoom:
*1 Resolution 1280×720.
• Panning/tilting platform
Panning range:
360 ° Endless panning
0 ° – 350 °
Panning speed:
Manual: Approx. 0.065 °/s – 120 °/s
Preset: Up to approx. 300 °/s
Operational range: –25 ° – 205 °
(level – downward – level)
Manual: Approx. 0.5 °/s – 100 °/s
Preset: Up to approx. 300 °/s
Operational range: -30° – 90°
(level – downward)
Tilting range:
Manual: Approx. 0.065 °/s – 120 °/s Manual: Approx. 0.5 °/s – 100 °/s
Preset: Up to approx. 300 °/s
Preset: Up to approx. 100 °/s
Number of the preset positions: 256
Auto mode:
Auto track/ Auto pan/ Preset sequence/ Patrol
Self return:
10 s/ 20 s/ 30 s/ 1 min/ 2 min/ 3 min/ 5 min/ 10 min/ 20 min/
30 min/ 60 min
Tilting speed:
• Network
Network:
Resolution*1:
H.265/ H.264
JPEG (MJPEG)
10BASE-T/100BASE-TX, RJ45 connector
S6131
S6130
2 mega pixel [16:9] (30 fps mode)/
2 mega pixel [16:9] (60 fps mode)
1920x1080, 1280x720, 640x360, 320x180
3 mega pixel [4:3] (30 fps mode)
2048x1536*2, 1280x960, 800x600, VGA, 400x300, QVGA
S6111
1.3 mega pixel [16:9] (30 fps mode)/
1.3 mega pixel [16:9] (60 fps mode)
1280×720, 640×360, 320×180
1.3 mega pixel [4:3] (30 fps mode)
1280×960, 800×600, VGA, 400×300, QVGA
33
Image compression method*3:
H.265/ H.264 Transmission priority:
Constant bit rate / Variable bit rate / Frame rate / Best effort
Frame rate:
1 fps/ 3 fps/ 5 fps*/ 7.5 fps*/ 10 fps*/ 12 fps*/ 15 fps*/ 20 fps*/
30 fps*/ 60 fps*
* The frame rate is limited to “bit rate”. When a value with an asterisk (*) is selected, the actual frame rate may be lower that the
value selected.
Bit rate per client:
64 kbps/ 128 kbps*/ 256 kbps*/ 384 kbps*/ 512 kbps*/
768 kbps*/ 1024 kbps*/ 1536 kbps*/ 2048 kbps*/ 3072 kbps*/
4096 kbps*/ 6144 kbps*/ 8192 kbps*/ 10240 kbps*/
12288 kbps*/ 14336 kbps*/ 16384 kbps*/ 20480 kbps*/
24576 kbps*/ --FREE ENTRY-* The available range of the bit rate varies depending on the setting
selected for “image capture size”.
Image quality:
• For "Constant bit rate", "Frame rate", and "Best effort":
Motion priority/ Normal/ Quality priority
• "VBR":
0 Super fine/1 Fine/ 2/ 3/ 4/ 5 Normal/ 6/ 7/ 8/ 9 Low
Transmission type:
Unicast/ Multicast
JPEG (MJPEG) Image quality:
0 SUPER FINE/ 1 FINE/ 2/ 3/ 4/ 5 NORMAL/ 6/ 7/ 8/ 9 LOW
(10 steps: 0-9)
Transmission type: Pull/ Push
Refresh interval:
0.1 fps/ 0.2 fps/ 0.33 fps/ 0.5 fps/ 1 fps/ 2 fps/ 3 fps/ 5 fps/ 6 fps/
10 fps/ 12 fps/ 15 fps/ 30 fps
(JPEG frame rates are limited when using JPEG and H.265/H.264
simultaneously)
Smart coding
Smart Facial Coding*
On(Smart Facial Coding)/ On(AUTO VIQS)/ Off
* Smart Facial Coding is only available with Stream(1).
GOP(Group of pictures) control
On(Advanced)*/ On(Low)/ On(Mid)/ Off
*On(Advanced) is only available with H.265.
Audio compression method: G.726 (ADPCM) : 16 kbps/ 32 kbps
G.711
: 64 kbps
: 64 kbps/ 96 kbps/ 128 kbps
AAC-LC*4
Bandwidth control:
Unlimited/ 64 kbps/ 128 kbps/ 256 kbps/ 384 kbps/ 512 kbps/
768 kbps/ 1024 kbps/ 2048 kbps/ 4096 kbps/ 6144 kbps/
8192 kbps/ 10240 kbps/ 15360 kbps/ 20480 kbps/ 25600 kbps/
30720 kbps/ 35840 kbps/ 40960 kbps/ 51200 kbps
34
Protocol:
IPv6: TCP/IP, UDP/IP, HTTP, HTTPS, FTP, SMTP, DNS, NTP, SNMP,
DHCPv6, RTP, MLD, ICMP, ARP, IEEE 802.1X, DiffServ
IPv4: TCP/IP, UDP/IP, HTTP, HTTPS, RTSP, RTP, RTP/RTCP, FTP,
SMTP, DHCP, DNS, DDNS, NTP, SNMP, UPnP, IGMP, ICMP,
ARP, IEEE 802.1X, DiffServ
Security
User authentication / Host authentication / HTTPS* /
Alteration detection of video file*
* The certification is pre-installed.
OS*5:
Microsoft Windows 10
Microsoft Windows 8.1
Microsoft Windows 8
Microsoft Windows 7
Windows Internet Explorer 11 (32-bit)
Browser*5:
Windows Internet Explorer 10 (32-bit)
Windows Internet Explorer 9 (32-bit)
Windows Internet Explorer 8 (32-bit)
14 (Number of sessions that can connect to cameras at the same time)
Maximum concurrent
* Depends on network conditions
access number:
FTP client:
Alarm image transmission, FTP periodic transmission (When the
FTP transmission is failed, backup on an optional SD memory card
is available.)
Up to 16 camera images can be displayed simultaneously on a multi-screen.
Multi-screen:
(Including the camera itself)
Compatible SDXC/SDHC/SD Manufactured by Panasonic (SD speed class 4 or higher)
memory card*6, *7
SDXC memory card: 64 GB, 128 GB, 256 GB
SDHC memory card: 4 GB, 8 GB, 16 GB, 32 GB
SD memory card : 2 GB
(except miniSD memory card and microSD memory card)
* Use of cards above Class 10 is recommended.
Cellular phone compatibility: JPEG image,
AUX control (by access level)
Mobile terminal compatibility: iPad / iPhone (iOS 4.2.1 or later), AndroidTM mobile terminals
(As of July, 2017)*8
*1 H.265/H.264 can be selected for each stream.
*2 Used by super resolution techniques.
*3 Transmission for 4 streams can be individually set.
*4 Only use AAC-LC (Advanced Audio Coding - Low Complexity) when recording audio on an SD
memory card.
*5 For further information about PC system requirements and precautions for when using Microsoft
Windows or Windows Internet Explorer, click “Manual” - “Open” from the supplied CD-ROM and
refer to “Notes on Windows / Internet Explorer versions”.
*6 Refer to our website (https://security.panasonic.com/support/info/) for latest information about
the compatible SD memory cards.
*7 When repeatedly recording images on an SD memory card using the auto overwrite function,
make sure to use an SD memory card with high reliability and durability.
*8 For further information about compatible devices, refer to our website
(https://security.panasonic.com/support/info/).
35
Optional accessories
S6131
S6111
Wall Mount Bracket
Ceiling Embedding Bracket
Ceiling Mount Bracket
Dome cover (Smoke dome type)
Dome cover (Clear dome type)
WV-Q119
WV-Q126A
WV-Q105A
WV-CS5S
WV-CS5C
S6130
Wall Mount Bracket (Smoke dome type)
Wall Mount Bracket (Clear dome type)
Ceiling Embedding Bracket (Smoke dome type)
Ceiling Embedding Bracket (Clear dome type)
Ceiling Mount Bracket (Smoke dome type)
Ceiling Mount Bracket (Clear dome type)
Ceiling Mount Bracket
Inner Cover
WV-Q158S
WV-Q158C
WV-Q159S
WV-Q159C
WV-Q160S
WV-Q160C
WV-Q105A
WV-Q161
36
For U.S. and Canada:
For Europe and other countries:
Panasonic System Communications
Company of North America,
Unit of Panasonic Corporation
of North America
Panasonic Corporation
Two Riverfront Plaza, Newark, NJ 07102-5490
Authorised Representative in EU:
Panasonic Canada Inc.
Panasonic Testing Centre
Panasonic Marketing Europe GmbH
Winsbergring 15, 22525 Hamburg, Germany
www.panasonic.com/business/
For customer support, call 1.800.528.6747
5770 Ambler Drive, Mississauga,
Ontario, L4W 2T3 Canada
(905)624-5010
www.panasonic.ca
http://www.panasonic.com
Panasonic Corporation
Osaka, Japan
© Panasonic Corporation 2017
fle0717-1087 PGQP2479YA
Download PDF
Similar pages