Camera OSD Manual
P/N : 38801K502
PRINTED IN KOREA
Distributed by
Before installing, operating or adjusting this product, please read this instruction
booklet carefully and completely.
Camera menu is subject to be changed without prior notice to upgrade and quality
increase and we may use slip sheet for the change.
Please check the camera version and the slip sheet if the camera menu and
this manual menu is not matched.
CONTENTS
SETUP MENU
CONTENTS
MAIN MENU
MAIN MENU
3p
EXPOSURE
4p
WHITE BALANCE
6p
IMAGE
7p
INTELLIGENCE
9p
SPECIAL FUNC
10p
DISPLAY
11p
SPECIFICATION
12p
MENU
MODEL
EXPOSURE
WHITE BAL
IMAGE
INTELLIGENCE
SPECIAL FUNC
DISPLAY
D&N
[EXIT]
[DFLT]
[SAVE]
Functions can be setup using “Menu Key Command”
of Visca protocol.
The menu consists of the “Main Menu” and “Sub Menu”.
The main menu is displayed where 7 camera functions
can be selected.
To the push of each main menu selection, the sub-menu is
displayed
If you want save the menu, select [SAVE].
If you want not save the menu, select [EXIT]
(After select, Power off -> on)
If you want default the menu, select [DFLT]
◆ MODEL
◈ MODEL : Select model
► D&N / COLOR / IR CDS
02
03
SETUP MENU
SETUP MENU
EXPOSURE
EXPOSURE
MENU
EXPOSURE
MODEL
EXPOSURE
WHITE BAL
IMAGE
INTELLIGENCE
SPECIAL FUNC
DISPLAY
D&N
[EXIT]
[DFLT]
[SAVE]
MODE
BRIGHTNESS
SHUT SPEED
DSS
AGC
FLICKERLESS
WDR/BLC
DAY&NIGHT
[BACK]
[SAVE]
DC
8
AUTO
OFF
ON
OFF
OFF
[DFLT]
◈ LENS : Select LENS type
► DC
▷ MODE : INDOOR, OUTDOOR, DEBLUR
► MANUAL
▷ MODE : NORMAL, DEBLUR
◈ BRIGHTNESS : Adjust brightness level
► 0(dark) ~ 20(bright) steps
◈ SHUT SPEED : Can be set in AUTO or MANUAL
► AUTO / x2, x3, x4, 1/30(25),1/60(50),1/120(100),1/240,
1/500, 1/1000,1/2000,1/4000,1/8000, 1/16000,1/30000,
1/60000 sec
◈ DSS : Select maximum DSS(Digital Slow Shutter)
► OFF / x2, x3, x4
◈ FLICKERLESS : Select Flickerless mode
► OFF / ON (remove screen flicker)
◈ AGC : Select Auto Gain Control
► OFF / ON
04
◈ WDR/BLC : Select WDR(Wide Dynamic Range)
or BLC(Back Light Compensation)
► WDR↲
▷ LEVEL : Adjust WDR level.
► LOW, MID-LOW, MIDDLE, MID-HIGH, HIGH
※ WDR doesn’t work in Shutter Manual Mode.
► BLC↲
▷ POSITION : Adjust the window position
▷ SIZE : Adjust the window size
※ Can’t use WDR and BLC at the same time.
(When WDR On, BLC is Off. And when BLC is On,
WDR is Off)
◈ DAY&NIGHT : Select Day&Night
▷ MODE : AUTO / EXT-IN / DAY / NIGHT
► AUTO↲ (When using IR-CDS model)
▷ POLARITY : ACTIVE LOW / HIGH
► EXT-IN↲ (When using D&N and COLOR model)
▷ POLARITY : ACTIVE LOW / HIGH
▷ DELAY : 0 ~ 255 sec
▷ THRS : 0 ~ 28
Day↔Night switching level in Auto Mode.
Switching in lower lux with higher threshold level.
▷ GAP : LOW, MID-LOW, MIDDLE, MID-HIGH, HIGH
Margin between Day →Night switching level and
Night →Day switching level.
▷ ANTI-SAT : LED saturation improves. (0~20)
▷ BURST : OFF / ON
05
SETUP MENU
SETUP MENU
WHITE BALANCE
IMAGE
MENU
D&N
[EXIT]
[DFLT]
[SAVE]
MENU
WHITE BAL
MODEL
EXPOSURE
WHITE BAL
IMAGE
INTELLIGENCE
SPECIAL FUNC
DISPLAY
MODE
RED GAIN
BLUE GAIN
CHROMA
[BACK]
[SAVE]
AUTO
----10
[DFLT]
◈ AWB : Select WHITE BALANCE mode
► AUTO / ONE PUSH / MANUAL / INDOOR / OUTDOOR
▷ AUTO : Automatically adjusts color according to
the available lighting.
▷ ONE PUSH : It is a fixed white balance mode that
may be automatically readjusted only by pressing
ONE PUSH
▷ MANUAL↲ : Color can be corrected when the user
increases or decreases “RED GAIN” or “BLUE GAIN”.
▷ INDOOR : Set color temperature to be Indoor light
(3700°K)
▷ OUTDOOR : Set color temperature to be Outdoor light
(5100°K)
◈RED GAIN : Adjust R gain value
► 0 ~ 20 steps
◈BLUE GAIN : Adjust B gain value
► 0 ~ 20 steps
◈ CHROMA : Adjust CHROMA gain value
► 0 ~ 20 steps
06
IMAGE
MODEL
EXPOSURE
WHITE BAL
IMAGE
INTELLIGENCE
SPECIAL FUNC
DISPLAY
D&N
[EXIT]
[DFLT]
[SAVE]
HLC
DNR
MIRROR
SHARPNESS
ACE
DEFOG
FREEZE
GAMMA
E.ZOOM
[BACK]
[SAVE]
AUTO
OFF
5
OFF
OFF
OFF
0.55
OFF
[DFLT]
◈ HLC : Select High Light Compensation.
When extremely bright light is projected to the camera
masking is used on the portion to prevent partial saturation
on the monitor.
▷ MODE : OFF / ON / NIGHT
▷ LEVEL : 0 ~ 20 steps
▷ COLOR : 0 ~ 13 steps
◈ DNR : Select Digital Noise Reduction
► AUTO / OFF / LOW / MIDDLE / HIGH
◈ MIRROR : Select a flip mode
► OFF / H / V / H&V
▷ H : You can flip the picture horizontally on the screen
▷ V : You can flip the picture vertically on the screen
▷ H&V : You can flip the picture horizontally & vertically
on the screen
07
SETUP MENU
IMAGE
◈ SHARPNESS : Adjust sharpness level
► 0 ~ 10 steps
◈ ACE : Select Digital WDR (Wide Dynamic Range)
► OFF / LOW / MIDDLE / HIGH
◈ DEFOG : Carry out defog function
► OFF / ON↲
▷ MODE : AUTO / MANUAL
▷ LEVEL : LOW / MIDDLE / HIGH
※ Can’t use DEFOG and ACE at the same time
(When ACE On, DEFOG is Off. And when DEFOG is On,
ACE is Off)
◈ Freeze : Select real or still mode
► OFF / ON
◈ GAMMA : Select GAMMA
► 0.45 / 0.50 / 0.55 / 0.60 / 0.65
◈ E.ZOOM
► OFF / ON
▷ LIMIT : Max x2 ~ x19, x21, x23, x25, x28, x32
▷ POSITION : Select maximum digital zoom magnification.
※ Can’t use Digital Zoom when the motion detection is
turned on.
08
SETUP MENU
INTELLIGENCE
MENU
INTELLIGENCE
MODEL
EXPOSURE
WHITE BAL
IMAGE
INTELLIGENCE
SPECIAL FUNC
DISPLAY
D&N
PRIVACY
MOTION
[EXIT]
[DFLT]
[BACK]
[SAVE]
OFF
OFF
[SAVE]
[DFLT]
◈ PRIVACY : Hide an area you want to hide on the screen
► OFF / ON↲
▷ MASK# : Select mask area number (1 ~ 24)
▷ MODE : Mask enable or disable (OFF / ON)
▷ POSITION : Adjust the mask position
▷ SIZE : Adjust the mask size
▷ COLOR : Select mask color (0 ~ 13)
▷ TRANS : Select mask transparency level (0 ~ 4)
◈ MOTION : When there is movement of the subject
in the screen, there will be an motion detection
► OFF / ON↲
▷ AREA# : Setting 3 areas(1~3) of motion detection
▷ MODE : OFF / ON
(Limit and define areas of motion detection)
▷ SENSITIVITY : Adjust sensitivity of MD (0 ~ 20 steps)
More sensitive to setting to low step with sensitivity
▷ POSITION : Adjust the Area position
▷ SIZE : Adjust the Area size
▷ INTERVAL TIME :Select the alarm interval time
(0 ~ 255sec)
▷ DWELL TIME : Select the duration time about changing
MD mode (0 ~ 255sec)
09
SETUP MENU
SETUP MENU
SPECIAL FUNC
DISPLAY
MENU
D&N
[EXIT]
[DFLT]
[SAVE]
MENU
SPECIAL FUNC
MODEL
EXPOSURE
WHITE BAL
IMAGE
INTELLIGENCE
SPECIAL FUNC
DISPLAY
DEFECT
SYSTEM
HD FORMAT
COMM
[BACK]
[SAVE]
NTSC
1080P
[DFLT]
◈ DEFECT : Compensates for bad pixels that may occur.
Occurs when the whole screen is in full black or if there is
bad pixelation and it changes the THRS values until
the screen is fixed.
◈ SYSTEM : Select NTSC(30fps) or PAL(25fps).(NTSC / PAL)
◈ HD FORMAT : Select Digital output 1080P or 720P.
(1080P / 720P)
◈ COMM : Set up the camera ID, baud rate, protocol
▷ ID : Select the camera ID
► 1 ~ 255
▷ BAUD RATE : Select serial communication speed
► 2400 / 4800 / 9600 / 19200 / 38400 / 57600 / 115200bps
▷ PROTOCOL : Select operating protocol
► VISCA / PELCO-D / PELCO-P / UPDATE
DISPLAY
MODEL
EXPOSURE
WHITE BAL
IMAGE
INTELLIGENCE
SPECIAL FUNC
DISPLAY
D&N
[EXIT]
[DFLT]
[SAVE]
DISP SEL
SET TITLE
INIT SEL
SET INIT MSG
LANGUAGE
[BACK]
[SAVE]
ON
ON
ENGLISH
[DFLT]
◈ DISP SEL : Select display item.
► OFF / ON↲
▷ ID : OFF / ON
▷ TITLE : OFF / ON
▷ ZOOM RATIO : OFF / ON
▷ SYSTEM MSG : OFF / ON (MD Alarm and Wait message)
◈ SET TITLE : Select camera title menu (Text edit)
◈ INIT SEL : Select display initial message.
► OFF / ON↲
▷ ID : OFF / ON
▷ BAUDRATE : OFF / ON
▷ PROTOCOL : OFF / ON
▷ VERSION : OFF / ON
▷ INIT MSG : OFF / ON
◈ SET INIT MSG : modify initial message. (Text edit)
◈ LANGUAGE : Select language.
► English / Simplified Chinese / Traditional Chinese / Japanese
※ Character Table of Text edit Mode
i
10
11
SPECIFICATION
Model
SPECIFICATION
NTSC
PAL
Defog
Total Pixels
2010(H) x 1108(V) = 2,227,080 (pixels)
Freeze
Active pixels
1944(H) x 1092(V) = 2,122,848 (pixels)
GAMMA
Scanning system
Resolution
Min. illumination
S/N Ratio
MODEL
LENS
Brigntness
Shutter speed
NTSC
PAL
Off / On (Auto / Manual)
Off / On
0.45 / 0.50 / 0.55 / 0.60 / 0.65
Progressive
E.Zoom
Off / Max x2 ~ x32
Digital ; 1920x1080p(1080p/30fps) ,
PRIVACY
Off / On (24 points)
1280x720p(720p/30fps)
MOTION
Off / On (3 points)
Analog : 700TVL
Defect
One Push
Color : 1.0 lux , BW : 0.5lux
System
NTSC / PAL
Color DSS : 0.002 lux , BW DSS : 0.001 lux
Video Output
HD : HD-SDI, BT.1120
HD Format
Comm
1080P / 720P
Baud Rate : 2400 / 4800 / 9600 / 19200 /
Analog : NTSC / PAL (without WDR)
38400 / 57600 / 115200
more than 50dB (AGC off)
Protocol : VISCA / Pelco-D / Pelco-P / Update
D&N / COLOR / IR CDS
DC / Manual
0 ~ 20
Auto / Manual (x2, x3, x4, 1/30(1/25) ~ 1/60000 )
Disp Sel (Off / On)
Set Title
Init Sel (Off / On)
Set Init Msg
ID / Title / Zoom Ratio / System Message
Text Edit
ID / Baud Rate / Protocol / Version / Init. Message
Text Edit
DSS
Off / x2 / x3 / x4
Language
English / Simplified Chinese / Traditional Chinese / Japanese
AGC
Off / On
OSD Text
0~9,A~Z,a~z
Flickerless
Off / On
Power Source
WDR/BLC
Off / WDR / BLC
DAY&NIGHT
Auto / Ext-in / Day / Night
WHITE BAL
Power Consumption
Power Input
DC12V±10%
150mA
Connector
Auto / One Push / Manual / Indoor / Outdoor
Video Output(HD-SDI)
MMCX Connector
HLC
Off / On / Night
Operating Temperature
-10℃ ~ +50℃ (Humidity : 0%RH ~ 80%RH)
DNR
Off / Low / Middle / High / Auto
Storage Temperature
-20℃ ~ +60℃ (Humidity : 0%RH ~ 90%RH)
Mirror
Off / H / V / H&V
Sharpness
ACE
12
Model
1/3" Panasonic CMOS
Image Sensor
0 ~ 10
Off / Low / Middle / High
13
Download PDF
Similar pages