Quick Start Guide O4VLD5

Quick

Start Guide

O4VLD5

Available from A1 Security Cameras

www.a1securitycameras.com email: [email protected]

1

Warning and Caution

■ If the product does not work properly, please contact your dealer or the nearest service center. Never attempt to disassemble the camera yourself. Any unauthorized changes or modifications could void the warranty.

■ Do not allow water or liquid intrusion into the camera.

■ All installation and operation here should conform to local electrical safety codes. Make sure the device is firmly installed on the wall or ceiling.

■ Do not use camera beyond specified voltage range.

■ Do not drop the camera or subject it to physical shock.

■ Avoid touching the camera lens.

■ If cleaning is necessary, please use cleaning cloth to wipe it gently.

■ Do not aim the camera at the sun or extremely bright light sources.

■ Do not place the camera in extremely hot or cold environments and dusty and damp locations. Do not expose it to highly electromagnetic radiation.

■ Do not block any ventilations.

2

Package

Available from A1 Security Cameras

www.a1securitycameras.com email: [email protected]

Camera

Quick start guide

4 tapping screws PA 4×35

CD

Drill template

Rubber plug Junction box

Plastic plug ×4

Screwdriver

33

OOvervieww

1

2

3

4

1 Mounting Base 3 MIC in connector

2 Ethernet connector 4 DC power connector

Available from A1 Security Cameras

www.a1securitycameras.com email: [email protected]

Security C ap

DC12V

* 1 It is recommended to install the security cap for outdoor installations.

* 2 DC 12V power supply is not required if a PoE switch or injector is used to power the camera.

► Connecting Network Cable

1 2 3

① Loosen the nut from the main element.

② Run the network cable (without RJ 45 connector) through both elements. Then crimp the cable with RJ 45 connector .

③ Connect the cable to the hermetic connector. Then tighten the nut and the main cover .

Available from A1 Security Cameras

www.a1securitycameras.com email: [email protected]

4

Installation

* Before you start, please make sure that the wall or ceiling is strong enough to withstand three times the weight of the camera.

① Install junction box onto the wall by using the screws provided.

② Loosen the screws to open the lower dome.

Low er Dome

Available from A1 Security Cameras

www.a1securitycameras.com email: [email protected]

③ Connect the cables, mount the rubber plug to the gap of the mounting base and fasten the camera onto the junction box.

Ru bber Plug

④

Three-axis Adjustment-Before adjustment, preview the image of the camera on a monitor and then adjust the camera according to the figure below to get an optimum angle.

Pan 0°~355°

Tilt 0°~65°

Rotation 0°~355°

Available from A1 Security Cameras

www.a1securitycameras.com email: [email protected]

⑤ Install the lower dome back to the camera and fix it with the screws.

5

Web Operation and Login

IP Scanner can search for the device on the local network.

● Operation

① Make sure that the camera and the PC are connected to the same local network. The camera is set to DHCP by default.

② Install IP Scanner from the CD and run it after installation.

Available from A1 Security Cameras

www.a1securitycameras.com email: [email protected]

③ In the device list, you can view the IP address, model number, and

MAC address of each device. Select the applicable device and double click to open up the web viewer. You can also manually enter the IP

address in the address bar of the web browser.

The login interface is shown above. Default user name is admin and password is 1234. After logging in, follow directions to install applicable plugins.

Available from A1 Security Cameras

www.a1securitycameras.com email: [email protected]