OWNER’S MANUAL & OPERATING INSTRUCTIONS
3000 PSI / 2.5 GPM
PRESSURE WASHER
MODEL NUMBER
76520
SAVE THESE INSTRUCTIONS
Important Safety Instructions
are included in this manual.
MADE IN CHINA
REV 76520-20120821
10006 Santa Fe Springs Road
Santa Fe Springs CA 90670
USA / 1-877-338-0999
www.championpowerequipment.com
Have questions or need assistance?
Do not return this product to the store!
WE ARE HERE TO HELP!
Visit our website:
www.championpowerequipment.com
for more info:
• Product Info & Updates
• Frequently Asked Questions
• Tech Bulletins
• Product Registration
– or –
Call our Customer Care Team Toll-Free at:
1-877-338-0999
WARNING:
The Engine Exhaust from this product contains chemicals known to the State of California
to cause cancer, birth defects or other reproductive harm.
*We are always working to improve our products. Therefore, the enclosed product may differ slightly from the image on the cover.
76520
3000 PSI / 2.5 GPM
Pressure Washer
Table of Contents
Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
Pressure Washer . . . . . . . . . . . . . . . . . . . . . . . . 1
Accessories . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
This Booklet . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
Manual Conventions . . . . . . . . . . . . . . . . . . . . . . . . 2
Safety Rules . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3
Controls and Features . . . . . . . . . . . . . . . . . . . . . . . 5
Pressure Washer . . . . . . . . . . . . . . . . . . . . . . . . 5
Parts Included. . . . . . . . . . . . . . . . . . . . . . . . . . 6
Assembly . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
Remove the Pressure Washer from the
Shipping Carton . . . . . . . . . . . . . . . . . . . . . . . . 7
Install the Wheel Kit . . . . . . . . . . . . . . . . . . . . . 7
Install Handle to Bottom Frame. . . . . . . . . . . . . . . 7
Add Engine Oil . . . . . . . . . . . . . . . . . . . . . . . . . . 7
Add Fuel. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
Attach the Pressure Gun . . . . . . . . . . . . . . . . . 9
Connect the High Pressure Hose. . . . . . . . . . . . . 9
Connect to Garden Hose . . . . . . . . . . . . . . . . . 9
Operation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
Pressure Washer Location. . . . . . . . . . . . . . . . . 10
Before Starting the Engine . . . . . . . . . . . . . . . . 10
Starting the Engine . . . . . . . . . . . . . . . . . . . . . 10
Distance from Cleaning Surface . . . . . . . . . . . . 10
High Pressure Wash . . . . . . . . . . . . . . . . . . . . . 11
Low Pressure Wash . . . . . . . . . . . . . . . . . . . . . 11
Detergent Use. . . . . . . . . . . . . . . . . . . . . . . 11
System Flush . . . . . . . . . . . . . . . . . . . . . . . 11
Adjustable Unloader . . . . . . . . . . . . . . . . . . . . . . 12
Depressurize System . . . . . . . . . . . . . . . . . . . . 12
Operating Tips. . . . . . . . . . . . . . . . . . . . . . . . . 12
Stopping the Engine. . . . . . . . . . . . . . . . . . . . . 12
Operation at High Altitudes. . . . . . . . . . . . . . . . . 13
Maintenance and Storage . . . . . . . . . . . . . . . . . . . 14
Engine Maintenance. . . . . . . . . . . . . . . . . . . . . 14
Oil . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14
Spark Plugs . . . . . . . . . . . . . . . . . . . . . . . . 14
Air Filter. . . . . . . . . . . . . . . . . . . . . . . . . . . 14
Cleaning . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15
Adjustments . . . . . . . . . . . . . . . . . . . . . . . . 15
Maintenance Schedule . . . . . . . . . . . . . . . . . 15
Pressure Washer Maintenance . . . . . . . . . . . . . . 15
Cleaning Spray Nozzle . . . . . . . . . . . . . . . . . 15
Storage . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Engine Stored for Less than 30 days . . . . . . . . .
Engine Stored for Over 30 Days. . . . . . . . . . . . . .
Pressure Washer Storage . . . . . . . . . . . . . . . . .
Winter Storage . . . . . . . . . . . . . . . . . . . . . . . .
Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . .
Engine Specifications . . . . . . . . . . . . . . . . . . . .
Pressure Washer Specifications . . . . . . . . . . . . .
Fuel . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Oil. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Spark Plugs . . . . . . . . . . . . . . . . . . . . . . . . . .
Maintenance Valve Clearance . . . . . . . . . . . . . .
Troubleshooting . . . . . . . . . . . . . . . . . . . . . .
Pressure Washer Parts Diagram. . . . . . . . . . . . .
Pressure Washer Parts List . . . . . . . . . . . . . . . .
Engine Parts Diagram . . . . . . . . . . . . . . . . . . .
Engine Parts List . . . . . . . . . . . . . . . . . . . . . . .
Warranty . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Warranty Qualifications. . . . . . . . . . . . . . . . . . .
Repair/Replacement Warranty . . . . . . . . . . . . . .
Do not return the unit to the place of
purchase . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Warranty Exclusions . . . . . . . . . . . . . . . . . . . . .
Normal Wear . . . . . . . . . . . . . . . . . . . . . . .
Installation, Use and Maintenance . . . . . . . . .
Other Exclusions . . . . . . . . . . . . . . . . . . . . .
Limits of Implied Warranty and
Consequential Damage . . . . . . . . . . . . . . . . . . .
Contact Information . . . . . . . . . . . . . . . . . . . . .
Address . . . . . . . . . . . . . . . . . . . . . . . . . . .
Customer Service . . . . . . . . . . . . . . . . . . . .
Technical Service . . . . . . . . . . . . . . . . . . . .
15
15
16
16
16
17
17
17
17
17
17
17
18
19
20
21
22
23
23
23
23
23
23
23
23
23
23
23
23
23
ENGLISH 76520
Introduction
Introduction
Accessories
Congratulations on your purchase of a Champion Power
Equipment pressure washer. CPE designs and builds
pressure washers to strict specifications. With proper
use and maintenance, this pressure washer will bring
years of satisfying service.
Champion Power Equipment manufactures and sells
accessories designed to help you get the most from
your purchase. To find out more about our accessories,
please visit our web site at:
www.championpowerequipment.com
Pressure Washer
This Booklet
This unit is a gasoline engine driven pressure washer. It is
designed for use in cleaning with or without detergent and
is suitable for decks, patios, house siding, vehicles, lawn
furniture, barbecue grills, gardening tools and more.
Every effort has been made to ensure the accuracy and
completeness of the information in this manual. We reserve
the right to change, alter and/or improve the product and
this document at any time without prior notice.
Record the model and serial numbers as well as date and place of purchase for future reference. Have this
information available when ordering parts and when making technical or warranty inquiries.
Champion Power Equipment Support
1-877-338-0999
Model Number
76520
Serial Number
Date of Purchase
Purchase Location
For Oil Type see ‘Add Engine Oil‘ section. For Fuel Type see ‘Add Fuel‘ section.
1
REV 76520-20120821
76520 ENGLISH
Manual Conventions
This manual uses the following symbols to help differentiate between different kinds of information. The safety symbol
is used with a key word to alert you to potential hazards in operating and owning power equipment.
Follow all safety messages to avoid or reduce the risk of serious injury or death.
DANGER
DANGER indicates an imminently hazardous
situation which, if not avoided, will result in death
or serious injury.
WARNING
WARNING indicates a potentially hazardous
situation which, if not avoided, could result in
death or serious injury.
CAUTION
CAUTION used without the safety alert symbol
indicates a potentially hazardous situation which, if
not avoided, may result in property damage.
NOTE
If you have questions regarding your pressure
washer, we can help. Please call our help line at
1-877-338-0999
CAUTION
CAUTION indicates a potentially hazardous
situation which, if not avoided, may result in minor
or moderate injury.
REV 76520-20120821
2
ENGLISH 76520
Safety Rules
WARNING
Read this manual thoroughly before operating your
pressure washer. Failure to follow instructions could
result in serious injury or death.
WARNING
The engine exhaust from this product contains
chemicals known to the state of California to cause
cancer, birth defects, or other reproductive harm.
DANGER
Engine exhaust contains carbon monoxide, a
colorless, odorless, poison gas. Breathing carbon
monoxide will cause nausea, dizziness, fainting or
death. If you start to feel dizzy or weak, get to fresh
air immediately.
Operate pressure washer outdoors only in a well
ventilated area.
DO NOT operate the pressure washer inside
any building, including garages, basements,
crawlspaces and sheds, enclosure or compartment,
including the pressure washer compartment of a
recreational vehicle.
DO NOT allow exhaust fumes to enter a confined
area through windows, doors, vents or other
openings.
DANGER CARBON MONOXIDE, using a pressure
washer indoors CAN KILL YOU IN MINUTES.
DANGER
Rotating parts can entangle hands, feet, hair,
clothing and/or accessories.
Traumatic amputation or severe laceration can result.
Keep hands and feet away from rotating parts.
Tie up long hair and remove jewelry.
Operate equipment with guards in place.
DO NOT wear loose-fitting clothing, dangling
drawstrings or items that could become caught.
3
REV 76520-20120821
WARNING
Sparks can result in fire or electrical shock.
When servicing the pressure washer:
Disconnect the spark plug wire and place it where it
cannot contact the plug.
DO NOT check for spark with the plug removed.
Use only approved spark plug testers.
WARNING
Running engines produce heat. Severe burns can
occur on contact. Combustible material can catch
fire on contact.
DO NOT touch hot surfaces.
Avoid contact with hot exhaust gases.
Allow equipment to cool before touching.
Maintain at least three feet of clearance on all
sides to ensure adequate cooling.
Maintain at least five feet of clearance from
combustible materials.
WARNING
DO NOT let water in the pump freeze.
See Storage section in the manual for instructions
regarding winter storage.
If water has frozen in the pressure washer, thaw the
pressure washer in a warm room before starting.
DO NOT pour hot water on or into the pump;
internal parts will be damaged and your warranty
will be voided.
WARNING
NEVER spray flammable liquids or use pressure
washer in areas containing combustible dust, liquids,
or vapor.
NEVER operate this machine in a closed building or
in or near an explosive environment.
• DO NOT remove fuel tank cap or fill fuel tank while
engine is hot or running (allow engine to cool two
minutes before refueling). Always fill the tank slowly.
• Never disconnect the high pressure discharge hose
from the machine while the system is pressurized.
76520 ENGLISH
DANGER
Safety Rules
WARNING
Fuel and fuel vapors are highly flammable and
extremely explosive.
Fire or explosion can cause severe burns or death.
Unintentional startup can result in entanglement,
traumatic amputation or laceration.
Rapid retraction of the starter cord will pull hand and
arm towards the engine faster than you can let go.
Unintentional startup can result in entanglement,
traumatic amputation or laceration.
Broken bones, fractures, bruises or sprains could result.
When adding or removing fuel:
When starting engine, pull the starter cord slowly
until resistance is felt and then pull rapidly to avoid
kickback.
Turn the pressure washer off and let it cool for at
least two minutes before removing the fuel cap.
Loosen the cap slowly to relieve pressure in the tank.
Only fill or drain fuel outdoors in a well-ventilated area.
DO NOT pump gas directly into the pressure washer
at the gas station. Use an approved container to
transfer the fuel to the pressure washer.
DO NOT overfill the fuel tank.
Always keep fuel away from sparks, open flames,
pilot lights, heat and other sources of ignition.
DO NOT light or smoke cigarettes.
When starting the pressure washer:
DO NOT attempt to start a damaged pressure
washer.
Make certain that the gas cap, air filter, spark plug,
fuel lines and exhaust system are properly in place.
Allow spilled fuel to evaporate fully before
attempting to start the engine.
Make certain that the pressure washer is resting
firmly on level ground.
When operating the pressure washer:
DO NOT move or tip the pressure washer during
operation.
DO NOT tip the pressure washer or allow fuel or oil
to spill.
When transporting or servicing the pressure washer:
Make certain that the fuel shutoff valve is in the off
position and the fuel tank is empty.
Disconnect the spark plug wire.
When storing the pressure washer:
Store away from sparks, open flames, pilot lights,
heat and other sources of ignition.
DANGER
Keep clear of nozzle.
DO NOT point the pressure wand at a person, an
animal or yourself.
Always wear safety glasses or goggles and
protective equipment (hearing protection, gloves,
rubber boots, protective clothing) when operating or
performing maintenance.
• Never put hand or fingers over the spray tip while
operating the unit.
• Never try to stop or deflect leaks with any body part.
• Always engage the trigger safety latch in the safe
position when spraying is stopped even if only for a
few moments.
CAUTION
Improper treatment or use of the pressure washer can
damage it, shorten its life and void your warranty.
Use the pressure washer only for intended uses.
Operate only on level surfaces.
DO NOT expose pressure washer to excessive
moisture, dust, or dirt.
DO NOT allow any material to block the cooling slots.
DO NOT use the pressure washer if:
–– Equipment sparks, smokes or emits flames
–– Equipment vibrates excessively
CAUTION
NEVER run the unit dry.
Be sure the water supply is completely turned on
before operating the unit.
REV 76520-20120821
4
ENGLISH 76520
Controls and Features
Read this owner’s manual before operating your pressure washer. Familiarize yourself with the location and function
of the controls and features. Save this manual for future reference.
Pressure Washer
8
9
2
1
3
14
4
5
10
11
7
6
13
(1) Muffler
(2) Air Filter – Protects the engine by filtering dust
and debris from the intake air.
5
12
(8) Gun Holder – Used to hold gun when assembled
and in use.
(3) Fuel Tank – 0.90 gal. (3.4 L)
(9) Gun Assembly – Gun and High pressure wand for
power washing.
(4) Engine Switch
(10) Garden Hose Connection
(5) Fuel Valve Knob – Used to turn fuel supply on and
off to engine.
(11) Detergent Tank
(6) Recoil Starter – Used to manually start the engine.
(13) 12” Never Flat Tires
(7) Choke
(14) High Pressure Hose Hanger – Used to hold high
pressure hose when not in use.
REV 76520-20120821
(12) High Pressure Hose Connection
76520 ENGLISH
Controls and Features
Parts Included
Your 76520 Gasoline Powered Pressure Washer ships
with the following parts:
Gun Assembly
–– Pressure Gun. . . . . . . . . . . . . . . . . . . . . . . . . . . 1
–– Wand . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
–– Quick Connect Nozzles . . . . . . . . . . . . . . . . . . . . 4
Hoses
–– 25 ft. High Pressure Hose . . . . . . . . . . . . . . . . . . 1
Other
–– Oil Funnel . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
–– Spark Plug Socket. . . . . . . . . . . . . . . . . . . . . . . . 1
25 ft. High
Pressure Hose
REV 76520-20120821
6
ENGLISH 76520
Assembly
Your pressure washer requires some assembly. This unit
ships from our factory without oil. It must be properly
serviced with fuel and oil before operation.
If you have any questions regarding the assembly of your
pressure washer, call our help line at 1-877-338-0999.
Please have your serial number and model number available.
Remove the Pressure Washer from the
Shipping Carton
1. Set the shipping carton on a solid, flat surface.
2. Remove everything from the carton except the
pressure washer.
3. Carefully cut each corner of the box from top to bottom.
Install Handle to Bottom Frame
1. Line up the handle with the bottom frame.
2. Make sure the handle holes are lined up with the
bottom frame spring button. (A)
3. Slide the handle downward on the bottom frame, until
the spring buttons have popped through the holes on
the handle frame. A “click” may sound. (B)
4. Gently pull up on the handle to make sure that two
frames have made a solid connection and that the
handle can not be pulled off without pressing on the
spring buttons to release it.
Install the Wheel Kit
CAUTION
A
The wheel kit is not intended for over-the-road use.
B
You will need the following tools to install the wheels:
• 17 mm wrench OR adjustable wrench (not included)
• Socket wrench with a 16 mm socket (not included)
• Pliers (not included)
1. Before adding top frame, oil, and fuel install the wheels
to the sides of the pressure washer.
2. Slide the M10x105 wheel bolt through the wheel
and then through the washer.
3. Slide the bolt through the mount point on the frame.
4. Fasten securely with the M10 nut.
5. Repeat steps 2-4 to attach the second wheel.
Add Engine Oil
CAUTION
DO NOT attempt to crank or start the engine before
it has been properly filled with the recommended
type and amount of oil. Damage to the pressure
washer as a result of failure to follow these
instructions will void your warranty.
NOTE
The recommended oil type is 10W-30 automotive oil.
1. Place the pressure washer on a flat, level surface.
7
REV 76520-20120821
76520 ENGLISH
Add Engine Oil Cont’d.
2. Remove oil fill cap/dipstick to add oil.
3. Add up to 0.63 qt. (0.6 L) of oil and replace oil fill
cap/dipstick.
4. Check engine oil level daily and add as needed.
CAUTION
The engine is equipped with a low oil shut-off and
will stop when the oil level in the crankcase falls
below the threshold level.
NOTE
Check oil often during the break-in period. Refer to
the Maintenance section for recommended service
intervals.
NOTE
The engine rotor has a sealed, pre-lubricated ball
bearing that requires no additional lubrication for
the life of the bearing.
Add Fuel
1. Use clean, fresh, regular unleaded fuel with a
minimum octane rating of 85 and an ethanol content
of less than 10% by volume.
2. DO NOT mix oil with fuel.
3. Clean the area around the fuel cap.
4. Remove the fuel cap.
5. Slowly add fuel to the tank. DO NOT OVERFILL. Fuel
can expand after filling. A minimum of ¼ in.
(0.64 cm) of space left in the tank is required
for fuel expansion, more than ¼ in. (0.64 cm) is
recommended. Fuel can be forced out of the tank as
a result of expansion if it is overfilled, and can affect
the stable running condition of the product.
Assembly
Add Fuel Cont’d.
When filling the tank, it is recommended to leave
enough space for the fuel to expand.
6. Screw on the fuel cap and wipe away any spilled fuel.
WARNING
Pouring fuel too fast through the fuel screen may
result in blow back of fuel at the operator while
filling.
CAUTION
Use regular unleaded gasoline with a minimum
octane rating of 85.
Do not mix oil and gasoline.
Fill tank to approximately ¼ in. (0.64 cm) below
the top of the tank to allow for fuel expansion.
DO NOT pump gas directly into the pressure washer
at the gas station. Use an approved container to
transfer the fuel to the pressure washer.
DO NOT fill fuel tank indoors.
DO NOT fill fuel tank when the engine is running
or hot.
DO NOT overfill the fuel tank.
DO NOT light cigarettes or smoke when filling the
fuel tank.
REV 76520-20120821
8
ENGLISH 76520
Assembly
Connect the High Pressure Hose
Add Fuel Cont’d.
NOTE
Our engines work well with 10% or less ethanol
blend fuels. When using blended fuels there are
some issues worth noting:
–– Ethanol-gasoline blends can absorb more water
than gasoline alone.
–– These blends can eventually separate, leaving
water or a watery goo in the tank, fuel valve and
carburetor.
–– With gravity-fed fuel supplies, this compromised
fuel can be drawn into the carburetor and cause
damage to the engine and/or potential hazards.
–– There are only a few suppliers of fuel stabilizer
that are formulated to work with ethanol blend
fuels.
–– Any damages or hazards caused by using
improper fuel, improperly stored fuel, and/
or improperly formulated stabilizers, are not
covered by manufacture’s warranty.
It is advisable to always shut off the fuel supply,
run the engine to fuel starvation and drain the tank
when the equipment is not in use for more than 30
days.
Attach the Pressure Gun Assembly
1. Attach the wand (A) to the gun (B).
2. Rotate the 22 mm nut (clock wise) until the wand is
secure. Tighten connection. Do not over tighten.
3. Connect the end of the high pressure hose (C) to the
gun inlet. Tighten connection clock wise. Do not
over tighten.
4. Slide the Quick Connect sleeve towards the gun.
Insert quick connect nozzle. Be sure the quick
connect sleeve is moved forward to secure the nozzle
in place.
A
B
C
9
REV 76520-20120821
Take the end of the High Pressure hose that isn’t
connected to the gun inlet and insert it into the
connection on the pump. Rotate hose end (clock wise)
until secure. Tighten connection.
Do not over tighten.
Connect the Garden Hose
Take the end of the garden hose that isn’t connected
to the main water supply and connect it to the pump.
Rotate the base of the hose connection until secure.
Tighten connection. Do not over tighten.
76520 ENGLISH
Operation
Starting the Engine Cont’d.
Pressure Washer Location
This pressure washer must have at least five feet of
clearance from combustible material. Leave at least
three feet of clearance on all sides of the pressure
washer to allow for adequate cooling, maintenance and
servicing. Place the pressure washer in a wellventilated
area. DO NOT place the pressure washer near vents
or intakes where exhaust fumes could be drawn into
occupied or confined spaces. Carefully consider wind and
air currents when positioning pressure washer.
NOTE
Keep choke lever in “Choke” position for 2 pulls
of the recoil starter. After second pull, move choke
lever to the “Run” position for up to the next 3
pulls of the recoil starter. Too much choke leads to
spark plug fouling/engine flooding due to the lack of
incoming air. This will cause the engine not to start.
NOTE
Before Starting the Engine
1. Turn the water supply ON.
2. Pull the trigger on the pressure gun to purge all
air from the pump and hose. This may take several
minutes.
3. Do not start the engine until a steady stream of water
is flowing from the nozzle.
CAUTION
Never operate your pressure washer without water.
If the engine does not start after 2 pulls, relieve
pump pressure by pulling the trigger on the pressure
washer gun.
NOTE
If the engine starts but does not run make certain
that the pressure washer is on a flat, level surface.
The engine is equipped with a low oil sensor that will
prevent the engine from running when the oil level
falls below a critical threshold.
Starting the Engine
Distance from Cleaning Surface
1. Make certain the pressure washer is on a flat, level
surface.
2. Press the engine switch to “ON” position (Item A).
3. Rotate the fuel valve to the “ON” position (Item B).
The distance between the spray nozzle and the cleaning
surface is another factor that affects the impact force of
the water. The impact force of the water increases as the
nozzle is moved closer to the surface. You can vary the
impact force by controlling
1. The nozzle’s fan pattern.
2. The nozzle’s angle to the cleaning surface.
3. The nozzle’s distance from the cleaning surface.
Never use a narrow high impact stream on a surface that
is susceptible to damage. Avoid spraying windows with
a narrow high impact stream or turbo nozzle. Doing so
may break the glass.
1. Before triggering the gun, select a nozzle with a wide
fan pattern.
2. Place the nozzle approximately 4-5 feet away from
the cleaning surface. Then hold the nozzle at a 45
degree angle to the cleaning surface. Trigger the gun.
3. Vary the fan pattern spray angle and the distance
to the cleaning surface until optimum cleaning
efficiency is achieved without damaging the surface.
B
C
A
D
4. Move the throttle lever (Item C) to the “Fast”
position.
5. Move the choke lever (Item D) to the “Choke”
position.
6. Pull the starter cord slowly until resistance is felt and
then pull rapidly. SEE NOTE.
7. As engine warms up, move the choke lever (Item D)
to “Run” and adjust the throttle as needed.
REV 76520-20120821
10
ENGLISH 76520
Operation
High Pressure Wash
CAUTION
Always engage the trigger safety latch when the unit
is not in use.
The trigger safety latch prevents the gun from being
triggered accidentally. Push the latch fully down to
engage it.
Your unit is equipped with a quick connect nozzle port.
Choose the appropriate nozzle tip for the job you are
performing.
CAUTION
The narrow high impact spray can damage some
surfaces.
A wide fan pattern distributes the impact of the water
over a larger area resulting in excellent cleaning action
with reduced risk of surface damage. Clean large surface
areas quickly using a wide fan pattern.
1. Fill the detergent tank with cleaning solution.
2. Install the Quick Connect detergent nozzle (black) in
the wand.
3. Be sure water supply is on. Start the engine. Pull the
gun trigger to spray the detergent solution.
WARNING
NEVER use Bleach in the Detergent Tank. It will
damage the pump and void the warranty.
NOTE
The gun will only draw detergent from the tank when
the Black Detergent Nozzle is installed in the wand.
NOTE
When spraying detergent, the detergent will be
diluted 1:12. Approximately 21oz. of detergent will be
consumed from the tank for every minute sprayed.
Low Pressure Wash
System Flush
Detergent Use
After using detergents, flush the suction system by
placing the detergent suction tube into a bucket of clean
water.
The use of detergents can dramatically reduce cleaning
time and assist in the removal of difficult stains. Many
detergents are customized for pressure washer use on
specific cleaning tasks. Pressure washer detergents are
as thick as water. Using thicker detergents – like dish
soap – will clog the chemical injection system.
NOTE
Use only detergents specially formulated for
pressure washers.
You can effectively clean surfaces by combining the
chemical action of detergents with high pressure rinses.
On vertical surfaces, apply the detergent starting at the
bottom and work your way upward. This method prevents
the detergent from sliding down and causing streaks.
Begin high pressure rinsing at the bottom and work
your way upward. On particularly tough stains, use a
brush in combination with detergents and high pressure
rinsing.
11
Detergent Use Cont’d.
REV 76520-20120821
WARNING
NEVER turn the water supply off before turning the
engine off.
76520 ENGLISH
Operation
Adjustable Unloader
The adjustable unloader, located on top of the valve, can
be turned counter clockwise (A) to decrease the PSI or
clockwise (B) to increase the PSI.
A
B
Operating Tips
CAUTION
Never operate your pressure washer without water.
CAUTION
Never connect your pressure washer to a hot water
supply.
Connecting your pressure washer to a hot water
source will significantly reduce the life of the pump
and will void the warranty.
NOTE
Decreasing the PSI can be useful to prevent
damage when cleaning delicate items.
Depressurize System
To depressurize, turn engine/motor off, turn water supply
off and squeeze gun trigger 2-3 times.
WARNING
NEVER disconnect the high pressure discharge hose
from the machine while the system is pressurized.
To reduce the risk of bodily injury or property damage,
always follow this procedure whenever spraying is
stopped, when work is completed, and before checking
or repairing any part of the system.
1. Engage the trigger safety latch.
2. Turn the unit off.
3. Remove the ignition cable from the spark plug.
4. Shut off the water supply.
5. Disengage the trigger safety latch and trigger the gun
to relieve pressure.
6. Re-engage the trigger safety latch.
7. Before overnight storage, long term storage, or
transporting unit, disconnect the water supply and
turn off the fuel supply valve.
CAUTION
Running the unit for more than one minute without
spraying water causes heat to build up in the pump.
In the event that the pump gets too hot, a thermal
relief valve will open to release the hot water.
Running the unit without spraying water can
damage pump components and will void the
warranty.
Stopping the Engine
1. Turn the Fuel Valve to the “OFF” position.
2. Let the engine run until fuel starvation has stopped
the engine. This usually takes a few minutes.
3. Press the engine switch to the “OFF” position.
4. Depressurize system.
5. Turn off and unplug all hoses. Never start or stop the
pressure washer unless the water supply is turned on.
Important: Always ensure that the Fuel Valve and the
Engine Switch are in the “OFF” position when the
engine is not in use.
NOTE
If the engine will not be used for a period of two (2)
weeks or longer, please see the Storage section for
proper engine and fuel storage.
REV 76520-20120821
12
ENGLISH 76520
Operation
Operation at High Altitude
The density of air at high altitude is lower than at sea
level. Engine power is reduced as the air mass and
air-fuel ratio decrease. Engine power and output will
be reduced approximately 3½% for every 1000 feet of
elevation above sea level. This is a natural trend and
cannot be changed by adjusting the engine. At high
altitudes increased exhaust emissions can also result
due to the increased enrichment of the air fuel ratio.
Other high altitude issues can include hard starting,
increased fuel consumption and spark plug fouling.
To alleviate high altitude issues other than the natural
power loss, Champion Power Equipment can provide a
high altitude carburetor main jet. The alternative main
jet and installation instructions can be obtained by
contacting Customer Support. Installation instructions
are also available in the Technical Bulletin area of the
Champion Power Equipment internet site.
The part number and recommended minimum altitude
for the application of the high altitude carburetor main
jet is listed in the table below.
In order to select the correct high altitude main jet
it is necessary to identify the carburetor model. For
this purpose, a code is stamped on the side of the
carburetor. Select the correct main jet part number
corresponding to the carburetor code found on your
particular carburetor.
Carburetor
Code
P19-1-Z
Main Jet
Part Number
Altitude
Standard
ST168F-2-1131000-17Z
Altitude
468.131017.01
6000 Feet
(1800 Meters)
WARNING
Operation using the alternative main jet at
elevations lower than the recommended minimum
altitude can damage the engine. For operation at
lower elevations, the standard main jet must be
used. Operating the engine with the wrong engine
configuration at a given altitude may increase
its emissions and decrease fuel efficiency and
performance.
13
REV 76520-20120821
76520 ENGLISH
The owner/operator is responsible for all periodic
maintenance .
MAINTENANCE AND STORAGE
Oil Cont’d.
WARNING
Never operate a damaged or defective pressure washer .
WARNING
Improper maintenance will void your warranty .
NOTE
Maintenance, replacement, or repair of emission
control devices and systems may be performed by any
non-road engine repair establishment or individual .
Complete all scheduled maintenance in a timely manner .
Correct any issue before operating the pressure washer .
Spark Plugs
1 . Remove the spark plug cable from the spark plug .
2 . Use the spark plug tool that shipped with your
pressure washer to remove the plug .
3 . Inspect the electrode on the plug . It must be clean and
not worn to produce the spark required for ignition .
4 . Make certain the spark plug gap is 0 .7 - 0 .8mm or
(0 .028 - 0 .031 in .) .
NOTE
For service or parts assistance, contact our help
line at 1-877-338-0999
0.7 - 0.8 mm
0.028 - 0.031 in.
Engine Maintenance
To prevent accidental starting, remove and ground spark
plug wire before performing any service .
Oil
Change oil when the engine is warm . Refer to the oil
specification to select the proper grade of oil for your
operating environment .
1 . Remove the oil drain plug with a 12 mm socket and
extension .
2 . Allow the oil to drain completely .
3 . Replace the drain plug .
4 . Remove oil fill cap/dipstick to add oil .
5 . Add up to 0 .63 qt . (0 .6 L) of oil and replace oil fill
cap/dipstick .
6 . Dispose of used oil at an approved waste
management facility .
NOTE
Once oil has been added, a visual check should show
oil about 1-2 threads from running out of the fill hole .
If using the dipstick to check oil level, DO NOT screw
in the dipstick while checking .
5 . Refer to the spark plug recommendation chart when
replacing the plug .
6 . Carefully thread the plug into the engine .
7 . Use the spark plug tool to firmly install the plug .
8 . Attach the spark plug wire to the plug .
Air filter
1 .
2 .
3 .
4 .
5 .
6 .
7 .
8 .
9 .
Unscrew wing nuts to remove the air filter cover .
Remove the air filter .
Separate the foam element and the paper element .
Tap the paper filter element to remove dirt and
debris . Use compressed air (25 PSI) to clear debris .
For the foam element: Wash in liquid detergent and
water . Squeeze thoroughly dry in a clean cloth .
Saturate in clean engine oil .
Squeeze in a clean, absorbent cloth to remove all
excess oil .
Reassemble the two elements and reattach .
Reattach the air filter cover and tighten wing nuts .
DO NOT OVER TIGHTEN .
REV 76520-20120821
14
ENGLISH 76520
Maintenance and Storage
Cleaning
Pressure Washer Maintenance
CAUTION
DO NOT spray engine with water.
Water can contaminate the fuel system.
Use a damp cloth to clean exterior surfaces of the engine.
Use a soft bristle brush to remove dirt and oil.
Use an air compressor (25 PSI) to clear dirt and debris
from the engine.
Adjustments
CPE recommends that you contact our service line at
1-877-338-0999 for all other service and/or adjustment
needs.
Maintenance Schedule
Follow the service intervals indicated in the schedule
below.
Service your pressure washer more frequently when
operating in adverse conditions.
Contact our help line at 1-877-338-0999 to locate the
nearest Champion Power Equipment certified service
dealer for your maintenance needs.
Make certain that the pressure washer is kept clean and
stored properly. Only operate the unit on a flat, level
surface in a clean, dry operating environment. DO NOT
expose the unit to extreme conditions, excessive dust,
dirt, moisture or corrosive vapors.
CAUTION
DO NOT use a garden hose to clean the pressure washer.
Use a damp cloth to clean exterior surfaces of the
pressure washer.
Use a soft bristle brush to remove dirt and oil.
Use an air compressor (25 PSI) to clear dirt and debris
from the pressure washer.
Inspect all air vents and cooling slots to ensure that they
are clean and unobstructed.
Cleaning Spray Nozzle
Detach the quick connect nozzle from the wand. Use a
small wire rod (paper clip) to loosen up any particles in
the quick connect nozzle and flush with water.
Every 8 hours or daily
Check oil level
Clean around air intake and muffler
First 5 Hours
Change oil
Every 50 hours or every season
Clean air filter
Change oil if operating under heavy load or in hot
environments
Every 100 hours or every season
Change oil
Clean/Adjust spark plug
Check/Adjust valve clearance *
Clean spark arrester
Storage
For short and long-term storage, please follow these
guidelines.
NOTE
Engine switch should be in the “OFF” position
while pulling the recoil cord, and performing storage
maintenance steps.
Clean fuel tank and filter *
Every 250 hours
Clean combustion chamber*
Every 3 years
Replace fuel line
*To be performed by knowledgeable, experienced owners or
Champion Power Equipment certified dealers.
15
REV 76520-20120821
Engine Stored for Less than 30 Days
1. Allow the engine to cool completely before storage.
2. Clean engine according to the Maintenance section.
3. To extend the fuel storage life add a properly
formulated fuel stabilizer to the tank.
4. Ensure the fuel valve is in the “OFF” position.
76520 ENGLISH
Maintenance and Storage
Engine Stored for Over 30 Days
Pressure Washer Storage
1. Add a properly formulated fuel stabilizer to the tank.
2. Run the engine for a few minutes so the treated fuel
cycles through the fuel system and carburetor.
3. Turn the fuel valve to the “Off” position.
4. Let the engine run until fuel starvation has stopped
the engine. This usually takes a few minutes.
5. The engine needs to cool completely before cleaning
and storage.
6. Clean the engine according to the maintenance section.
7. Change the oil.
8. Remove the spark plug and pour about 1⁄2 ounce
of oil into the cylinder. Crank the engine slowly to
distribute the oil and lubricate the cylinder.
9. Reattach the spark plug.
1. Allow the pressure washer to cool completely before
storage.
2. Turn off the fuel supply at the fuel valve.
3. Clean the pressure washer according to the
instructions in the Maintenance section.
4. Store the unit in a clean, dry area out of direct sunlight.
DANGER
Engine exhaust contains odorless and colourless
carbon monoxide gas.
To avoid accidental or unintended ignition of the
product during periods of storage, the following
precautions should be followed:
–– When storing the pressure washer for short or
long periods of time make sure that the Engine
Switch and the Fuel Valve are set in the OFF
position.
NOTE
Our engines work well with 10% or less ethanol blend
fuels. When using blended fuels there are some issues
worth noting:
–– Ethanol-gasoline blends can absorb more water than
gasoline alone.
–– These blends can eventually separate, leaving water
or a watery goo in the tank, fuel valve and carburetor.
–– With gravity-fed fuel supplies, this compromised fuel
can be drawn into the carburetor and cause damage
to the engine and/or potential hazards.
–– There are only a few suppliers of fuel stabilizer that
are formulated to work with ethanol blend fuels.
–– Any damages or hazards caused by using improper
fuel, improperly stored fuel, and/or improperly
formulated stabilizers, are not covered by
manufacture’s warranty.
It is advisable to always shut off the fuel supply, run the
engine to fuel starvation and drain the tank when the
equipment is not in use for more than 30 days.
WARNING
Never store the pressure washer inside or next to
appliances where there is a source of heat or open
flame, spark or pilot light because they can ignite
gasoline vapors.
DO NOT store a pressure washer near fertilizer or any
corrosive material.
Even with an empty gas tank, gasoline vapors could
ignite.
Winter Storage
Protect your pressure washer parts from freezing.
1. Apply all storage instructions from previous sections.
2. Make sure pressure washer hose is free of all water
before storing for winter.
3. In order to prevent the pump from freezing you will
need to insert RV antifreeze.
4. You will need approximately 6 ounces of RV
Antifreeze, a funnel, and approximately
30 cm (12 in.) of garden hose or equivalent.
See diagram below.
5. Pour the antifreeze into the funnel, then pull on the
engine recoil starter to create suction in the pump
housing. Pull the recoil several times until antifreeze
comes out of the pump outlet.
REV 76520-20120821
16
ENGLISH 76520
Specifications
Spark Plugs
Engine Specifications
––
––
––
––
Model. . . . . . .
Displacement. .
Type . . . . . . . .
Start Type . . . .
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
. . . . . 66533
. . . . . 196cc
4-Stroke OHV
. . . . . Recoil
Pressure Washer Specifications
Maintenance Valve Clearance
––
––
––
––
––
––
––
––
––
–– Intake: 0.13 – 0.17 mm (0.005 – 0.007 in.)
–– Exhaust: 0.18 – 0.22 mm (0.007 – 0.009 in.)
Note: Tech bulletin regarding the valve adjustment
procedure is on www.championpowerequipment.com.
Model. . . . . . .
Max Pressure. .
Flow Capacity. .
Fuel Capacity. .
Gross Weight . .
Net Weight. . . .
Height. . . . . . .
Width . . . . . . .
Length. . . . . .
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
. . . . . . . . . . . 76520
. . . . . . . . . 3000 PSI
. . . . . . . . . 2.5 GPM
. . . . 0.90 gal. (3.4 L)
. . . 87.1 lbs. (39.5 kg)
. . 73.9 lbs. (33.5 kg)
. 38.2 inches (97 cm)
19.9 inches (50.6 cm)
36.3 inches (92.1 cm)
Fuel
Fuel capacity is 0.90 gal. (3.4 L). Use regular unleaded
gasoline with a minimum octane rating of 85 and an
ethanol content of less than 10% by volume.
Oil
Use 10W-30 automotive oil.
Oil capacity is up to 0.63 qt. (0.6 L).
Please reference the following chart for recommended
oil types for use in the pressure washer.
17
OEM spark plug: NHSP F6RTC
Replacement spark plug: NGK BPR6ES or equivalent
Make certain the spark plug gap is 0.7 - 0.8 mm or
(0.028 - 0.031 in.).
REV 76520-20120821
76520 ENGLISH
Troubleshooting
Problem
Cause
Solution
Pressure washer will not start
No fuel
Add fuel
Faulty spark plug
Replace spark plug
Low oil level
Fill crankcase to the proper level
Place pressure washer on a flat, level
surface
Choke in the wrong position
Adjust choke
Pressure washer will not start;
Pressure washer starts but runs
roughly
Spark plug wire loose
Attach wire to spark plug
Pressure washer gallops
Engine governor defective
Contact the help line
Unit does not reach high pressure
Water supply is restricted
Check hoses for leaks, blockage, kinks
Garden hose is too small
Replace with 5/8 in. garden hose or
larger
Garden hose inlet filter is clogged
Remove garden hose, clean filter and
rinse out
Not enough inlet water
Turn garden hose water on full force
Poor inlet water supply
Turn garden hose water on full force.
Check hose for leaks, blockage, or
kinks
Garden hose inlet filter is clogged
Remove garden hose, clean filter and
rinse out
Spray nozzle is obstructed
Remove particles with small wire rod
(see maintenance section in manual)
Pump is sucking air
Check all hoses and fittings, make
sure they are securely tightened down
and fastened. Turn off engine and
purge pump by squeezing trigger gun
until a steady stream of water flows
Detergent is too thick
Dilute detergent
Wand is on high pressure setting
Detergent only works on a low
pressure setting
Detergent hose is not connected to
the pump housing
Check connection. See diagram on
Page 10
Spray nozzle is obstructed
Clean nozzle and remove debris
Filter on detergent hose is clogged
Clean with warm water or replace
Chemical Injector valve (inside pump)
partially blocked or stuck
Quickly pull and release the gun trigger
4-5 time to clear the chemical injector
valve
Loose fittings
Tighten
Missing/worn-out rubber washer
Replace rubber washer
Spray wand leaks
Spray wand not properly attached
Tighten all connections
Can’t Pull Recoil
Pump will build pressure with each pull.
Pull gun trigger after 2 pulls of recoil, to
release pump pressure.
Spray pressure varies from high to low
Detergent wash is not functioning
properly
Garden hose connection leaks
For further technical support:
Technical Service
Mon – Fri 8:30 AM – 5:00 PM (PST/PDT)
Toll Free: 1-877-338-0999
tech@championpowerequipment.com
REV 76520-20120821
18
Specifications
Parts Diagram
19
REV 76520-20120821
ENGLISH 76520
76520 ENGLISH
#
Part Number
Parts List
Description
Qty
#
Part Number
Description
Qty
1
ST30QXG-0000101
Chemical Hose
1
18
819.250100.00
Compression Resistance Hose
1
2
ST29QXG-3300200
Inlet Filter Gasket
2
19
ST29QXG-2100003
Pin
2
3
ST30QXG-3300300
Hot Protection
1
20
ST-QT-0092
Frame
1
4
ST29QXG-2000001
Bolt 5/16-24 D22
4
21
GB41-N-10
Nut M10
2
5
GB93-LW-8
Spring Washer φ8
4
22
GB96-FW-10
Flat Washer Φ10
2
6
ST29QXG-2000006
Key SQ 3/16×1.57
1
23
13.012000.01
12in Wheel
2
7
168F-2-GC10
Engine
1
24
08.010082.10
Bolt M10×82
2
8
819.251000.00
Pump
1
25
ST29QXG-2100200
Bottom Rubber
2
9
819.252200.00
Connect Wand
1
26
08.008052.10
Bolt M8×52
2
10
GB41-N-8
Nut M8
10
27
816.201400.00
Frame Rubber
2
11
819.252100.00
Gun Assembly
1
28
GB41-N-8
Nut M8
2
12
819.252300.00
Nozzle"15"
1
29
ST168F-1090100-C
Screw Cap
2
13
819.252300.01
Nozzle"25"
1
30
819.250200.00
Cleanser Tank
1
14
819.252300.02
Nozzle"40"
1
31
819.250201.00
Tie-In
1
15
819.252300.03
Nozzle"Detergent"
1
32
819.200701.00
Handle (1)
1
16
ST22QXP-2100003
Grommet
4
33
08.006045.10
Bolt M6×45
2
17
819.200701.01
Handle (2)
1
34
819.200012.02
Pothook (Light)
1
REV 76520-20120821
20
21
143
114
139
138
REV 76520-20120821
1
137
136
11
2
14
135
134
3
133
4
132
5
140
15
6
141
7
20
16
142
8
21
131
9
22
10
23
17
24
25
11
18
26
118 103
117
12
27
19
82
130 103
13
49
82
129
128
28
29
48
47
46
45
44
43
30
31
44
127
126
125
124
123
122
53
52
51
50
32
11
33
54
34
115
35
56
57
114
117
118
119
120
121
58
113
36
55
59
112
116
37
60
38
61
110
62
39
64
65
111
109
63
72
66
40
67
71
68
69
73
41
74
70
75
77
1
78
87
80
100
76
79
81
86
82
42
92
85
83
19
93
84
88
94
95
89
96
97
90
99
108
107
104 105 106
103
102
101
98
91
Specifications
ENGLISH 76520
Engine Parts Diagram
76520 ENGLISH
#
Part Number
Description
Qty
#
Part Number
Description
1
GB5789-FB6-8
Flange Bolt M6x8
5
73
ST168F-1040014-A
Oil Seal, Valve
2
2
ST160F-1061100-Q
Recoil Starter Cover
1
74
ST160F-1040003
Spring, Valve
2
3
ST160F-1061005
Recoil Starter Spring
1
75
ST160F-1040007
Retainer, Exhaust Valve
1
76
ST160F-1040001
Retainer, Intake Valve
1
77
ST160F-1040008
Rotator, Exhaust Valve
1
78
168.040202.34
Shaft, Rocker Arm
1
79
ST160F-1040022
Rocker Arm
2
80
ST160F-1040024
Screw, Valve Adjustment
2
81
ST168F-1040025
Lock Nut
2
82
GB90-W-6
Washer φ6
6
83
GB41-N-6
Nut M6
2
84
168.040201.34
Retainer, Rocker Arm
1
85
ST168F-1040027
Stud Bolt, Rocker Arm
2
86
168.040004.34
Guide Plate, Push Rod
1
87
ST168F-1040005
Push Rod
2
88
ST160F-1020002-A
Gasket, Valve Cover
1
89
ST168F-1020100-C
Valve Cover Assembly
1
90
ST160F-1020001
Breather Tube
1
91
GB5789-FB6-15
Flange Bolt M6x15
4
92
ST160F-1010002
Stud Bolt
2
93
ST168F-1100200-G
Gasket, Muffler
1
94
GB1667-S5-10
Screw M5×10
2
95
GB90-W-5
Washer φ5
2
96
GB93-LW-5
Lock Washer φ5
2
97
168.101200.34
Cover, Muffler
1
98
188.101300.34
Spark Arrester
1
99
GB1667-S4-6
Bolt M4X6
4
100
GB5781-B5-10
Bolt M5X10
2
101
168.101100.36
Muffler Assembly
1
102
GB1667-S6-16
Screw M6×16
2
103
GB93-LW-6
Lock Washer φ6
6
104
GB41-N-8
Nut M8
2
105
GB90-W-8
Washer φ8
2
106
GB93-LW-8
Lock Washer φ8
2
107
ST168FD-1100003-CARB
Gasket, SAI Valve
1
108
ST168FD-1100300-CARB
SAI Valve
1
109
ST168F-2-1010100-G
Cylinder Head
1
110
ST160F-1010001
Stud Bolt 6x110
2
111
ST160F-1130002-CPE
Gasket, Insulator
1
112
ST168F-1130001
Insulator, Carburetor
1
113
ST160F-1130003-CPE
Gasket, Carburetor
1
114
ST168F-2-1131000-G
Carburetor Assembly
1
115
ST160F-1130004
Washer, Air Cleaner Base
1
116
ST160F-1130100
Choke Handle
1
117
168.091100.34
Base, Air cleaner
1
118
GB5789-FB6-20
Flange Bolt M6x20
5
119
168.091003.36
Element, Air Cleaner
1
120
168.091200.36
Cover, Air Cleaner
1
121
ST168F-1090100-C
Nut, Air Cleaner Cover (Plastic)
2
122
168.070014.01
Pipe, Reversal Valve
1
123
ST160F-1070007
Clip
1
124
168.070013.00
Pipe, Air Cleaner
1
125
ST168F-1071400-GC
Carbon Canister
1
126
GB845-ST2.9-6.5
Screw
2
4
ST160F-1061009
Recoil Starter Rope
1
5
ST160F-1061001-A
Recoil Starter Reel
1
6
ST188F-1060006
Spring, Ratchet
2
7
ST188F-1060005
Starter Ratchet (Metal)
2
8
ST188F-1060004
Ratchet Guide Spring
1
9
ST188F-1060003
Ratchet Guide
1
10
ST188F-1060002
Screw, Ratchet Guide
1
11
GB5789-FB6-12
Flange Bolt M6x12
10
12
ST168F-1080100-G
Fan Cover Assembly
1
13
ST168F-1070008-G
Clip, Tube φ9.5
1
14
ST160F-1061200
Recoil Starter Knob
1
15
ST160F-1050010
Nut M14
1
16
ST160F-1060001-A
Start Hub
1
17
ST168F-1080001
Cooling Fan
1
18
ST168F-1120100
Flywheel
1
19
ST168F-1030100
Oil Seal
2
20
ST160F-1110106
Washer, Governor
1
21
ST160F-1110101
Governor Gear
1
22
ST160F-1110102
Pin, Weight
2
23
ST160F-1110104
Shaft, Governor Gear
1
24
ST160F-1110103
Circlip, Governor Gear
1
25
ST160F-1110107
Governor Weight
2
26
ST160F-1110105-A
Bushing, Governor
1
27
ST168F-1080200
Air Guide
1
28
ST160F-1030003
Drain Bolt
2
29
ST160F-1030004
Washer, Drain Bolt
2
30
ST168F-2-1030012-G
Crankcase
1
31
ST160F-1129000-G
Diode
1
32
ST160F-1127000-A
Oil Level Sensor
1
33
GB5758-AM7×35
Flange Bolt 7x35
2
34
ST168F-1050100
Connecting Rod Assembly
1
35
ST168F-2-1050001-Q
Crankshaft Assembly
1
36
GB276-BB-6205-UU
Radial Ball Bearing 6205
2
37
ST168F-1030008-G
Gasket, Crankcase
1
38
ST160F-1030001-B
Oil Dipstick
1
39
ST160F-1030002
Gasket, Oil Dipstick
2
40
ST168F-1030007-G
Crankcase Cover
1
41
GB5789-FB8-32
Flange Bolt 8x32
6
42
ST160F-1030005-B
Oil Filler Cap
1
43
ST168F-1110005
Spring, Throttle Return
1
44
ST160F-1110003
Governor Arm
1
45
GB41-N-6
Nut M6
3
46
ST160F-1110108
Washer, Governor (II)
1
47
ST160F-1110001
Shaft, Governor Arm
1
48
ST160F-1123000-G
Ignition Coil
1
49
GB5789-FB6-25
Flange Bolt 6x25
2
50
ST168F-1110006
Rod, Governor
1
51
ST168F-1110007
Spring, Governor
1
52
ST160F-1110004
53
ST160F-1110008
Pin, Shaft
1
54
168.111008.01
Sheath, Control Handle
1
55
168.111000.30
Control Assembly
1
56
ST168F-2-1040013
Lifter, Valve
2
57
ST168F-1030015-G
Dowel Pin 9x14
2
58
ST168F-2-1041000
Camshaft Assembly
1
59
GB1099-79
Key
1
60
ST168F-2-1050005
Piston
1
61
ST168F-1050003
Wrist Pin
1
62
ST168F-1050004
Piston Pin Clip
2
63
ST168F-1050200
Ring, Oil
1
64
ST168F-1050006
Ring, Second
1
65
ST168F-1050007
Ring, First
1
66
ST168F-2-1030009-G
Gasket, Cylinder Head
1
67
152FMD-1001007
Dowel Pin 10x16
2
68
ST168F-1040002
Valve, Intake
1
69
ST168F-1040006
Valve, Exhaust
1
70
ST168F-1080002-G
Gasket, Cylinder Head
1
71
F6RTC
Spark Plug
1
72
GB5789-FB8-55
Flange Bolt 8x55
4
Bolt, Governor Arm
1
Qty
127
03.032001.00
Washer
2
128
168.070100.05
Fuel Tank Cap
1
129
0902.070301.00
Fuel Filter
1
130
GB5789-FB6-29
Flange Bolt M6x29
1
131
168.071000.36
Fuel Tank Assembly
1
132
ST152FD-1070200
Inline Fuel Filter
1
133
ST1P68F-1070006-F
Clip
1
134
ST168F-1070200-G
Fuel Cock
1
135
ST168F-1070005-G
Tube 2
1
136
168.070010.34
Veil, Fuel Tank
1
137
ST01FD-05701001
Switch
1
138
ST168F-1070003-G
139
GB5781-B4-12
Bolt M4x12
1
140
GB5789-FB5-12
Flange Bolt M5x12
1
141
ST188FD-1070006A
Clip Ф8
3
142
ST168F-1070004-G
Tube 1
1
143A ST168F-2-1131000-17
Standard Main Jet
1
143B 468.131017.01
Altitude Main Jet
/
Knob, Fuel Valve
1
REV 76520-20120821
22
76520 ENGLISH
Warranty
WARRANTY
CHAMPION POWER EQUIPMENT
1 YEAR LIMITED WARRANTY
Effective September 1, 2006. Replaces all undated warranties
and all warranties dated before September 1, 2006.
Warranty Qualifications
Champion Power Equipment (CPE) will register this
warranty upon receipt of your Warranty Registration Card
and a copy of your sales receipt from one of CPE’s retail
locations as proof of purchase.
Please submit your warranty registration and your proof
of purchase within ten (10) days of the date of purchase.
Repair/Replacement Warranty
CPE warrants to the original purchaser that the
mechanical and electrical components will be free of
defects in material and workmanship for a period of one
(1) year from the original date of purchase (90 days for
commercial & industrial use). Transportation charges on
product submitted for repair or replacement under this
warranty are the sole responsibility of the purchaser.
This warranty only applies to the original purchaser and
is not transferable.
Do Not Return The Unit To The Place Of Purchase
Contact CPE’s Technical Service and CPE will troubleshoot
any issue via phone or e-mail. If the problem is not
corrected by this method, CPE will, at its option, authorize
evaluation, repair or replacement of the defective part or
component at a CPE Service Center. CPE will provide you
with a case number for warranty service. Please keep it
for future reference. Repairs or replacements without prior
authorization, or at an unauthorized repair facility, will not
be covered by this warranty.
Warranty Exclusions
This warranty does not cover the following repairs and
equipment:
Normal Wear
Pressure washers need periodic parts and service to
perform well. This warranty does not cover repair when
normal use has exhausted the life of a part or the
equipment as a whole.
Installation, Use and Maintenance
This warranty will not apply to parts and/or labor if
this pressure washer is deemed to have been misused,
neglected, involved in an accident, abused, loaded
beyond the pressure washer’s limits, modified, installed
improperly or connected incorrectly to any water supply.
Installation, Use and Maintenance Cont’d.
Normal maintenance such as spark plugs, air filters,
adjustments, fuel system cleaning and obstruction due
to buildup is not covered by this warranty.
Other Exclusions
This warranty excludes:
–– Cosmetic defects such as paint, decals, etc.
–– Wear items such as filter elements, o-rings, etc.
–– Accessory parts such as starting batteries, and
storage covers.
–– Failures due to acts of God and other force majeure
events beyond the manufacturer’s control.
–– Problems cause by parts that are not original
Champion Power Equipment parts.
Limits of Implied Warranty and Consequential Damage
Champion Power Equipment disclaims any obligation to
cover any loss of time, use of this product, freight, or
any incidental or consequential claim by anyone from
using this pressure washer. THIS WARRANTY IS IN
LIEU OF ALL OTHER WARRANTIES, EXPRESS OR
IMPLIED, INCLUDING WARRANTIES OF
MERCHANTABILITY OR FITNESS FOR A PARTICULAR
PURPOSE.
A unit provided as an exchange will be subject to the
warranty of the original unit. The length of the warranty
governing the exchanged unit will remain calculated by
reference to the purchase date of the original unit.
This warranty gives you certain legal rights which may
change from state to state. Your state may also have
other rights you may be entitled to that are not listed
within this warranty.
Contact Information
Address
Champion Power Equipment, Inc.
Customer Service
10006 Santa Fe Springs Rd.
Santa Fe Springs, CA 90670
www.championpowerequipment.com
Customer Service
Mon – Fri 8:30 AM – 5:00 PM (PST/PDT)
Toll Free:1-877-338-0999
info@championpowerequipment.com
Fax no.: 1 (562) 236-9429
Technical Service
Mon – Fri 8:30 AM – 5:00 PM (PST/PDT)
Toll Free: 1-877-338-0999
tech@championpowerequipment.com
REV 76520-20120821
23
Champion Power Equipment, Inc. (CPE),
The California Air Resources Board (CARB) and the United States Environment Protection Agency (U.S. EPA.)
Emission Control System Warranty
Your Champion Power Equipment (CPE) engine complies with both the U.S. EPA and state of California Air
Resources Board (CARB) emission regulations.
YOUR WARRANTY RIGHTS AND OBLIGATIONS:
The California Air Resources Board, US EPA AND CPE are pleased to explain the Federal and California Emission
Control Systems Warranty on your 2012 small off-road engine and engine powered equipment. In California, new,
small off-road engines and new equipment that use small off-engines must be designed, built and equipped to meet
the State’s stringent anti smog standards. In the other states, new engines and equipment must be designed, built
and equipped, at the time of sale, to meet U.S. EPA regulations for small non-road engines. CPE warrants the
emission control system on your small off-road engine and equipment for the period of time listed below, provided
there has been no abuse, neglect, unapproved modification, or improper maintenance of your equipment.
Your emission control system may include parts such as the carburetor, fuel-injection system, the ignition system,
catalytic converter and fuel lines. Also included may be hoses, belts, connectors and other emission related
assemblies. Where a warrantable condition exits, CPE will repair your small off-road engine at no cost to you
including diagnosis, parts and labor. For engines less than or equal to 80cc, only the fuel tank and fuel line is
subject to the evaporative emission control warranty requirements of this section.
MANUFACTURER’S EMISSION CONTROL SYSTEM WARRANTY COVERAGE:
This emission control system is warranted for two years, subject to provisions set forth below. If, during the
warranty period, emission related part on your engine is defective in materials or workmanship, the part will be
repaired or replaced by CPE.
OWNER WARRANTY RESPONSIBILITIES:
As the small off-road engine owner, you are responsible for the performance of the required maintenance listed in
your Owner’s Manual. CPE recommends that you retain all your receipts covering maintenance on your small offroad engine, but CPE cannot deny warranty solely for the lack of receipts or for your failure to ensure the
performance of all scheduled maintenance.
As the small off-road engine owner, you should however be aware that CPE may deny you warranty coverage if
your small, off-road engine or a part has failed due to abuse, neglect, improper maintenance or unapproved
modifications.
You are responsible for presenting your small off-road engine to an Authorized CPE service outlet or alternate
service outlet as described in (3)(f.) below, CPE dealer or CPE, Santa Fe Springs, Ca. as soon as a problem exists.
The warranty repairs should be completed in a reasonable amount of time, not to exceed 30 days.
If you have any questions regarding your warranty rights and responsibilities, you should contact:
Champion Power Equipment, Inc.
Customer Service
10006 Santa Fe Springs Road
Santa Fe Springs, CA 90670
1-877-338-0999
EMISSION CONTROL SYSTEM WARRANTY
The following are specific provisions relative to your Emission Control System Warranty Coverage.
1. APPLICABILITY: This warranty shall apply to 1995 and later model year California small off-road engines (for
other states, 1997 and later model year engines). The ECS Warranty Period shall begin on the date the new
engine or equipment is delivered to its original, end-use purchaser, and shall continue for 24 consecutive months
thereafter.
2. GENERAL EMISSIONS WARRANTY COVERAGE
CPE warrants to the original, end-use purchaser of the new engine or equipment and to each subsequent
purchaser that each of its small off-road engines is:
a. Designed, built and equipped so as to conform with all applicable regulations adopted by the Air
Resources Board pursuant to its authority in Chapters 1 and 2, Part 5, Division 26 of the Health and Safety Code,
and
b. Free from defects in materials and workmanship that cause the failure of a warranted part to be identical
in all material respects to the part as described in the engine manufacturer’s application for certification for a period
of two years.
3. THE WARRANTY ON EMISSION-RELATED PARTS WILL BE INTERPRETED AS FOLLOWS:
a. Any warranted part that is not scheduled for replacement as required maintenance in the Owners
Manual shall be warranted for the ECS Warranty Period. If any such part fails during the ECS Warranty Period, it
shall be repaired or replaced by CPE according to Subsection “d” below. Any such part repaired or replaced under
the ECS Warranty shall be warranted for any remainder of the ECS Warranty Period.
b. Any warranted, emissions-related part which is scheduled only for regular inspection as specified in the
Owners Manual shall be warranted for the ECS Warranty Period. A statement in such written instructions to the
effect of “repair or replace as necessary”, shall not reduce the ECS Warranty Period. Any such part repaired or
replaced under the ECS Warranty shall be warranted for the remainder of the ECS Warranty Period.
c. Any warranted, emissions-related part which is scheduled for replacement as required maintenance in
the Owner’s Manual shall be warranted for the period of time prior to the first scheduled replacement point for that
part. If the part fails prior to the first scheduled replacement, the part shall be repaired or replaced by CPE
according to Subsection “d” below. Any such emissions-related part repaired or replaced under the ECS Warranty,
shall be warranted for the remainder of the ECS Warranty Period prior to the first scheduled replacement point for
such emissions-related part.
d. Repair or replacement of any warranted, emissions-related part under this ECS Warranty shall be
performed at no charge to the owner at a CPE Authorized Service Outlet.
e. The owner shall not be charged for diagnostic labor which leads to the determination that a part covered
by the ECS Warranty is in fact defective, provided that such diagnostic work is performed at a CPE Authorized
Service Outlet.
f. CPE shall pay for covered emissions warranty repairs at non-authorized service outlets under the
following circumstances:
i. The service is required in a population center with a population over 100,000 according to U.S.
Census 2000 without a CPE Authorized Service Outlet AND
ii. The service is required more than 100 miles from a CPE Authorized Service Outlet. The 100 mile
limitation does not apply in the following states: Alaska, Arizona, Colorado, Hawaii, Idaho, Montana, Nebraska,
Nevada, New Mexico, Oregon, Texas, Utah and Wyoming.
g. CPE shall be liable for damages to other original engine components or approved modifications
proximately caused by a failure under warranty of an emission-related part covered by the ECS Warranty.
h. Throughout the ECS Warranty Period, CPE shall maintain a supply of warranted emission-related parts
sufficient to meet the expected demand for such emission-related parts.
i. Any CPE Authorized and approved emission-related replacement part may be used in the performance of
any ECS Warranty maintenance or repair and will be provided without charge to the owner. Such use shall not
reduce CPE’s warranty obligation.
j. Unapproved add-on or modified parts may not be used to modify or repair a CPE engine. Such use voids
this ECS Warranty and shall be sufficient grounds for disallowing an ECS Warranty claim. CPE shall not be liable
hereunder for failures of any warranted parts of a CPE engine caused by the use of such an unapproved add-on or
modified part.
EMISSION-RELATED PARTS INCLUDE THE FOLLOWING: (using those portions of the list applicable to the
engine)
Systems covered by this
warranty
Fuel Metering System
Fuel regulator, Carburetor and internal parts
Air Induction System
Air cleaner, Intake manifold
Ignition System
Spark plug and parts, Magneto ignition system
Exhaust System
Exhaust manifold, catalytic converter
Miscellaneous Parts
Tubing, Fittings, Seals, Gaskets, and Clamps associated with these listed
systems.
Fuel Tank, Fuel Cap, Fuel Line, Fuel Line Fittings, Clamps, Pressure
Relief Valves, Control Valves, Control Solenoids, Electronic Controls,
Vacuum Control Diaphragms, Control Cables, Control Linkages, Purge
Valves, Vapor Hoses, Liquid/Vapor Separator, Carbon Canister, Canister
Mounting Brackets, Carburetor Purge Port Connector
Evaporative Emissions
Parts Description
TO OBTAIN WARRANTY SERVICE:
You must take your CPE engine or the product on which it is installed, along with your warranty registration card or
other proof of original purchase date, at your expense, to any Champion Power Equipment dealer who is
authorized by Champion Power Equipment, Inc. to sell and service that CPE product during his normal business
hours. Alternate service locations defined in Section (3)(f.) above must be approved by CPE prior to service. Claims
for repair or adjustment found to be caused solely by defects in material or workmanship will not be denied because
the engine was not properly maintained and used.
If you have any questions regarding your warranty rights and responsibilities, or to obtain warranty
service, please write or call Customer Service at Champion Power Equipment, Inc.
Champion Power Equipment, Inc.
10006 Santa Fe Springs Road
Santa Fe Springs, CA 90670
1-877-338-0999
Attn.: Customer Service
Download PDF
Similar pages