P1
PASSPORT 1000
Mortise Lock
Installation Instructions
A8032G
04/16
Copyright 2016, Sargent Manufacturing Company, an ASSA ABLOY Group company.
All rights reserved. Reproduction in whole or in part without the express written
permission of Sargent Manufacturing Company is prohibited.
Table of Contents
8
Warning ....................................................................................3
General Description..................................................................4
Hardware Specifications..........................................................4
Electronic Specifications..........................................................4
Installation Wiring....................................................................5
Parts Breakdown......................................................................9
Installation Instructions.........................................................10
Operational Check .................................................................21
1
Warning
1
2
3
4
5
6
7
FCC
Changes or modifications to this unit not expressly approved by the party responsible
for compliance could void the user’s authority to operate the equipment.
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules.
These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment
generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause
harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation.
If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off
and on, the user is encouraged to try to correct the interference by one or more of the following measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
04/30/16
Copyright © 2016, Sargent Manufacturing Company, an ASSA ABLOY Group company. All rights reserved.
Reproductions in whole or in part without express written permission of Sargent Manufacturing Company is prohibited.
• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.
Industry Canada:
This Class B digital apparatus meets all requirements of the Canadian Interference Causing Equipment Regulations. Operation is subject
to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference
received, including interference that may cause undesired operation.
Cet appareillage numérique de la classe B répond à toutes les exigences de l’interférence canadienne causant des règlements
d’équipement. L’opération est sujette aux deux conditions suivantes: (1) ce dispositif peut ne pas causer l’interférence nocive, et (2) ce
dispositif doit accepter n’importe quelle interférence reçue, y compris l’interférence qui peut causer l’opération peu désirée.
“This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. This equipment should be
installed and operated with minimum distance 20cm between the radiator and your body. This transmitter must not be co-located or
operating in conjunction with any other antenna or transmitter.”
Under Industry Canada regulations, this radio transmitter may only operate using an antenna of a type and maximum (or lesser) gain approved for the transmitter by Industry Canada. To reduce potential radio interference to other users, the antenna type and its gain should
be so chosen that the equivalent isotropically radiated power (e.i.r.p.) is not more than that necessary for successful communication.
Conformément à la réglementation d’Industrie Canada, le présent émetteur radio peut fonctionner avec une antenne d’un type et d’un
gain maximal (ou inférieur) approuvé pour l’émetteur par Industrie Canada. Dans le but de réduire les risques de brouillage radioélectrique à l’intention des autres utilisateurs, il faut choisir le type d’antenne et son gain de sorte que la puissance isotrope rayonnée
équivalente (p.i.r.e.) ne dépasse pas l’intensité nécessaire à l’établissement d’une communication satisfaisante.
!
Any retrofit or other field modification to a fire rated opening can potentially impact the fire rating of the opening, and SARGENT Manufacturing makes no representations or warranties concerning what such impact may be in any specific situation. When retrofitting any
portion of an existing fire rated opening, or specifying and installing a new fire-rated opening, please consult with a code specialist or
local code official (Authority Having Jurisdiction) to ensure compliance with all applicable codes and ratings.
To avoid possible damage from electrostatic discharge (ESD), some basic precautions should be used when handling
electronic components:
• Minimize build-up of static by touching and/or maintaining contact with unpainted metal surfaces such as door hinges,
latches and mounting plates especially when mounting electronic components such as readers and controllers onto the door
•
Leave components (reader and controller) protected in their respective anti-static bags until ready for installation.
•
Do not touch pins, leads or solder connections on the circuit boards.
1-800-810-WIRE • www.sargentlock.com • A8032G
Passport 1000 P1 PoE Mortise Lock
2
General Description
An ANSI/BHMA Grade 1 lock utilizing Power over Ethernet (PoE) technology, the Passport 1000 P1
provides a cost-effective, future-proof solution for campuses. Featuring multiCLASS SE® Technology from
HID Global®, it provides simultaneous support for multiple credentials and offers an easy migration path
to higher security credentials and mobile access. Recognized for its contribution to sustainable buildings,
the P1 re-uses existing IEEE 802.3af PoE infrastructure, streamlines the installation process, reduces costs
and components, and minimizes power consumption.
3
4
Hardware Specifications
•
Complete locksets with controller
• ANSI/BHMA A156.25 Listed Grade 1 Compliant
•
ADA Compliant
•
Easily retrofits existing Passport 1000
door preps (mortise locks)
• Outside lever is unlocked through access
control credentials only
•
Latch 1/2" standard 3/4" throw fire-rated
double doors (optional) (41- prefix)
•
Deadlocking latch
•
Inside lever retracts latch
•
Copyright © 2016, Sargent Manufacturing Company, an ASSA ABLOY Group company. All rights reserved.
Reproductions in whole or in part without express written permission of Sargent Manufacturing Company is prohibited.
• May be used for indoor and outdoor applications
NOTE: A weather-protective gasket is required
for outdoor applications.
Electronic Specifications
• HID® multiCLASS SE® technology offers
support for the following credentials:
• 2.4 GHz credential compatibility:
04/30/16
• Outside lever controlled by any combination of
keypad, magnetic swipe, contactless reader or
mechanical cylinder
•
•
Secure Identity Object™ (SIO) on
Mobile IDs (Bluetooth Smart)
13.56 MHz credential compatibility:
•
2,400 users per lock; 10,000 event audit trail
•
Multiple time zone and holiday access scheduling
•
First-In unlock configuration, based on specified
time schedule
•
Uses existing Magstripe keycards (track 2)
•
Magnetic Stripe Card Coercivity:
HiCo (4000 Oersted) or LoCo (300 Oersted)
•
iCLASS®
•
iCLASS SE® (SIO-enabled)
•
Power Requirements: 55VDC, 90mA
•
iCLASS Seos®
•
•
SIO on MIFARE® Classic
•
SIO on MIFARE® DESfire® EV1
PoE Class 1 Device, as defined by IEEE
802.3af, requires less than 3.84 watts over
structured cabling
•
MIFARE® Classic
• UL Listed* - UL 294 Indoor Use
•
•
DESfire® EV1
NFC-enabled mobile phones
• CUL Listed - S319: Class 1
• UL 294 Access Control Ratings:
125 kHz credential compatibilty:
Destructive Attack
Level 1
•
Line Security
Level 1
Endurance
Level 4
Standby Power
Level 1
HID Prox®
• Magnetic Stripe
*UL testing was conducted on product powered by
UL Listed model 9001GR/AC injector; manufactured
by Microsemi Corp.
4
1-800-810-WIRE • www.sargentlock.com • A8032G
Passport 1000 P1 PoE Mortise Lock
Installation Wiring
Overview
SARGENT Passport Series PoE P1 Typical Application
Supplied by Others
Network Cable
Surface Mount RJ45
Network Switch (802.3af)
LMT: Lock Management Tool
A. PoE frame harness assembly
B. PoE data hinge from McKinney
(patent pending)
C. PoE door harness* from McKinney
D. Passport Series v.P1 PoE Lock
A
D
C
B
Copyright © 2016, Sargent Manufacturing Company, an ASSA ABLOY Group company. All rights reserved.
Reproductions in whole or in part without express written permission of Sargent Manufacturing Company is prohibited.
* Door width determines length
1-800-810-WIRE • www.sargentlock.com • A8032G
5
04/30/16
5
Passport 1000 P1 PoE Mortise Lock
Installation Wiring (Continued)
Supplied by CI
Certified Integrator (CI) supplies and terminates
the B-Splice connector and the
male RJ45 connector from harness to
end user provided facility cable
Patch Cable
Patch Panel to
PoE Switch
To building or electrical ground
B-Splice
Crimp Connector
RJ45-M
RJ45-F Jack
04/30/16
Copyright © 2016, Sargent Manufacturing Company, an ASSA ABLOY Group company. All rights reserved.
Reproductions in whole or in part without express written permission of Sargent Manufacturing Company is prohibited.
Frame-Side
Harness
Assembly
(15' length)
Cable: CAT 5e or higher
24 AWG
Notes:
Cable: CAT 5e,
26 AWG stranded,
100ohm
A
Molex-F Molex-M
Molex-F
B
RJ45-M
C
Ground
Ring Terminal
Secured to Lock
Mounting Plate
Wiring to TIA/568-B Standard
6
PoE Switch is
Terminated to
Earth Ground
Approved Software
D
Molex-M
PoE Switch
Patch Panel
Cable: CAT 5e or higher
24 AWG 100ohm
Ceiling
Supplied by End User
1-800-810-WIRE • www.sargentlock.com • A8032G
PoE
Lock
• Connectors go on only
one way. They cannot be
placed in an
incorrect position.
• Do not force and do not
offset connectors
• Be sure they are
completely seated (flush)
• PoE power source
cannot be connected to a
receptacle controlled by
a switch
Passport 1000 P1 PoE Mortise Lock
Installation Wiring (Continued)
A
Frame Harness Installation
Components and wire harness supplied by McKinney. Suggested installation:
Supplied by CI
Cut end / ceiling-side PoE harness:
B-Splice
Crimp Connector
TIA/EIA 568-B Standard Wiring
1
2
3 4 5 6 7
8
PIN
1
pin
8
8
pin
1
RJ45-M
1
White/Orange
2
2
Orange
2
3
White/Green
3
4
Blue
1
5
White/Blue
1
6
Green
3
7
White/Brown
4
8
Brown
4
Copyright © 2016, Sargent Manufacturing Company, an ASSA ABLOY Group company. All rights reserved.
Reproductions in whole or in part without express written permission of Sargent Manufacturing Company is prohibited.
Hinge side of PoE harness:
1. Feed cut end of harness into hole on hinge-side through single access hole.
2. Push one connector back through the hole and feed into the other access hole.
Each of the hinge-side harness connectors should end up threaded through
a different access hole and matched to the same size pin connector from
the door harness:
Cable
drain wire
concealed in
shrink tubing
• 4-pin male molex connector
• 6-pin male molex connector with ground wire
Molex-M
B
PoE Data Hinge
Frame
4-pin M
4-pin F
PoE Hinge
4-pin F
Hinge-side harness connectors:
• 4-pin female molex connector
• 6-pin female molex connector with ground wire
Lock-side harness connectors:
6-pin M
• 4-pin female molex connector
6-pin F
• 6-pin female molex connector with ground wire
6-pin F
1-800-810-WIRE • www.sargentlock.com • A8032G
7
04/30/16
Frame-Side
Harness
Assembly
(15' length)
Pair
Number
Do not confuse pair numbers with pin numbers. A pair number is
used for reference only (eg: 10BaseT Ethernet uses pairs 2 & 3). The
pin numbers indicate actual physical locations on the plug and jack.
Cable:
24AWG
Stranded
Drain
Wire for
Earth
Ground in
15' Frame
Harness
CAT 5e or higher
24 AWG 100ohm
Ceiling
Wire
Passport 1000 P1 PoE Mortise Lock
C
PoE Door Harness
Order of installation may vary. Refer to appropriate sections for instructions.
Hinge-side harness connectors:
•
4-pin male Molex connector
•
6-pin male Molex connector with ground wire
Lock-side harness connectors:
•
Ring terminal
•
Male RJ45 connector (crimped after cable is fed through door)
Notes:
•
Connectors go on only one way. They cannot be plugged to incorrect position.
•
Do not force and do not offset connectors.
•
Be sure they are completely seated (flush).
PoE Lock
4-pin F
4-pin F
4-pin M
RJ45-M
04/30/16
Copyright © 2016, Sargent Manufacturing Company, an ASSA ABLOY Group company. All rights reserved.
Reproductions in whole or in part without express written permission of Sargent Manufacturing Company is prohibited.
6-pin F
D
6-pin F
6-pin M
Cable: CAT 5e,
26 AWG stranded,
100ohm
PoE Lock
Order of installation may vary. Refer to appropriate sections for instructions.
1. Prop door open.
Inside of Door
2. Using the ring terminal, carefully route the assembly through the door
channel to the lock.
PoE
Harness
(Cat 5e)
8
1-800-810-WIRE • www.sargentlock.com • A8032G
Passport 1000 P1 PoE Mortise Lock
Parts Breakdown
P1 PoE Lock with Magnetic Card Swipe With or Without Keypad
4
3
2
ITEM No.
5
PART No.
DESCRIPTION
52-3583-[finish]
Outside Escutcheon Assembly, mag stripe
52-3582-[finish]
Outside Escutcheon Assembly, mag stripe and Keypad (shown)
52-4244-[finish]
Outside Escutcheon Assembly, Mag Swipe, Keypad, and HID 125 kHz Prox
52-4759-[finish]
Outside Escutcheon Assembly, iCLASS, keypad, mag stripe, Prox, smart card (MIFARE, DESFIRE)
52-4777-[finish]
Outside Escutcheon Assembly, iCLASS, mag stripe, Prox, smart card (MIFARE, DESFIRE)
52-4787-[finish]
Outside Escutcheon Assembly, FeliCa, keypad, mag stripe, Prox
52-4788-[finish]
Outside Escutcheon Assembly, FeliCa, mag stripe, Prox
52-4894-[finish]*
Outside Escutcheon Assembly, Standard Reader and Keypad
52-4895-[finish]*
Outside Escutcheon Assembly, Standard Reader
52-4896-[finish]*
Outside Escutcheon Assembly, Felica Reader and Keypad
52-4897-[finish]*
Outside Escutcheon Assembly, Felica Reader
2
52-4779
Mounting Plate Assembly
3
52-4940
PoE Controller Assembly
4
52-4776-[finish]
Inside Escutcheon Assembly with Privacy Button
5
52-5373
Door Position Switch Kit
1
Copyright © 2016, Sargent Manufacturing Company, an ASSA ABLOY Group company. All rights reserved.
Reproductions in whole or in part without express written permission of Sargent Manufacturing Company is prohibited.
1
*Bluetooth Smart option
®
1-800-810-WIRE • www.sargentlock.com • A8032G
9
04/30/16
6
Passport 1000 P1 PoE Mortise Lock
Parts Breakdown (Continued)
5
4
3*
7
7
7
8
8
9
Tools Required:
6
10
04/30/16
Copyright © 2016, Sargent Manufacturing Company, an ASSA ABLOY Group company. All rights reserved.
Reproductions in whole or in part without express written permission of Sargent Manufacturing Company is prohibited.
10
10
ITEM
PART No.
DESCRIPTION
1
See catalog
#41 Cylinder (1-1/8" Minimum Length)
2
Consult Factory
Cylinder Rosette
3
P1-82276-[finish]*
Lock body with deadbolt & with cylinder
P1-82277-[finish]*
Lock body with deadbolt without cylinder
P1-82278-[finish]*
Lock body without deadbolt with cylinder
#2 Phillips screwdriver
•
Flat head
•
T20 Torx® driver
•
Security allen wrench
P1-82279-[finish]*
Lock body without deadbolt without cylinder
4
77-2592
130 KB Thumb turn for Deadbolt Functions Only
5
See catalog
Inside Lever Handle
6
See catalog
Outside Lever Assembly
7
82-3211
Trim Pack - 8200 Standard Levers (shown)
82-5357
Trim Pack - 8200 Deco Levers & 7900 all lever styles
8
See catalog
Mortise Rose
9
82-0347
Spindle Spring
10
Consult factory
Mortise screw pack - specify finish (includes: wood and metal lock
body screws, faceplate screws, and strike screws)
11
82-0578
Outside Front Plate (Electrical, Latchbolt & Guardbolt)
82-0579
Outside Front Plate (Electrical, Deadbolt, Latchbolt and Guardbolt)
*Bluetooth® Smart option
10
11
•
1-800-810-WIRE • www.sargentlock.com • A8032G
Passport 1000 P1 PoE Mortise Lock
Door Preparation
A. Verify Hand and Bevel of Door
Left Hand
Hinges Left.
Open Inward.
“LH”
Left Hand
Reverse Bevel
Hinges Left.
Open Outward
“LHRB”
Right Hand
Hinges Right.
Open Inward.
“RH”
Right Hand
Reverse Bevel
Hinges Right.
Open Outward.
“RHRB”
B. Verify Product Label
C. Door Preparation
• Field prep template: A8064 for wood and metal doors
• Door manufacturers template: 4651
Outside of Door
Copyright © 2016, Sargent Manufacturing Company, an ASSA ABLOY Group company. All rights reserved.
Reproductions in whole or in part without express written permission of Sargent Manufacturing Company is prohibited.
1
Installation Instructions
Inside of Door
Through Bolt Holes
Inside Mounting Plate
Mounting Holes
Through Bolt Holes
Raceway for PoE
Raceway for PoE
Controller Cutout
Controller Cutout
Cylinder Hole
Thumb Turn Location
(Deadbolt Functions Only)
Lever Handle Holes
Lever Handle Holes
Mortise
Pocket
1-800-810-WIRE • www.sargentlock.com • A8032G
11
04/30/16
7
Passport 1000 P1 PoE Mortise Lock
2 Prepare Lock Body
1. Reverse Lock Hand
Red surface of locking piece must face the
outside/locked side of door. To rotate locking
piece (Fig. 2A):
Right Hand
Lock Shown
a. Position lock body with red surface
of locking piece visible.
b. Insert blade type screwdriver into
locking piece slot to rotate locking
piece toward back of lock body.
c. Rotate the locking piece 180° until
RED surface is on opposite side.
Locking Guide Slot:
Red color indicates
locked side.
Fig. 2A
Push In
Note: Red indicates locked side (outside).
2. Reverse Latch Hand
Beveled surface of latch must face strike (Fig. 2B).
The deadlatch is self adjusting.
Triangular Slot
To change hand of latchbolt:
a. Insert screwdriver into spade (triangular)shaped slot.
Latchbolt
04/30/16
Copyright © 2016, Sargent Manufacturing Company, an ASSA ABLOY Group company. All rights reserved.
Reproductions in whole or in part without express written permission of Sargent Manufacturing Company is prohibited.
b. Rotate screwdriver 90º to push latch out
until back of latch clears lock front; then
rotate latch 180º.
Latch will then re-enter lock body.
Note: Latch cannot be unscrewed.
Fig. 2B
12
1-800-810-WIRE • www.sargentlock.com • A8032G
Passport 1000 P1 PoE Mortise Lock
3 Install Lock Body
Note: Do not pull the lock into the pocket using the harness alone.
Ensure that the wire harness is not pinched between the lock and the mortise pocket.
1. Feed the wire harness into the mortise pocket and
through inside preparation hole as depicted in Figure 3.
2. Carefully push the lock body into the pocket while
lightly applying tension to the wire harness.
3. Insert (2) #12-24 screws into the lock body (Fig.4)
and partially tighten* with a screw driver.
*Do not fully tighten until cylinder and levers
are installed and properly aligned.
Inside of Door
Cat 5e cable
from hinge
(2) #12-24
screws
Wire
Harness
Fig. 3
1-800-810-WIRE • www.sargentlock.com • A8032G
13
04/30/16
Copyright © 2016, Sargent Manufacturing Company, an ASSA ABLOY Group company. All rights reserved.
Reproductions in whole or in part without express written permission of Sargent Manufacturing Company is prohibited.
Ground
Wire
Passport 1000 P1 PoE Mortise Lock
4 Outside Cylinder Installation
1. Slide the spring and the rosette onto the cylinder.
2. Rotate the cylinder into cylinder hole with fingers.
3. Insert key 75% of the way and utilize the key to rotate the cylinder
into the rest of the cylinder hole.
Note: Do not attempt to tighten all the way.
4. Verify that orientation of cylinder has the SARGENT logo as depicted
in Fig. 4A.
IMPORTANT: Position cylinder so that the
SARGENT logo is positioned correctly.
5. Hand tighten the cylinder clamp screw with Phillips screwdriver to
prevent unscrewing of the cylinder (Fig 4C).
6. Test cylinder function: Correct
• Key retracts latchbolt and deadbolt (7976 function)
Incorrect
Fig. 4A
• Key retracts latchbolt (7978 function)
• Cylinder not present for 7977 and 7979 functions
04/30/16
Copyright © 2016, Sargent Manufacturing Company, an ASSA ABLOY Group company. All rights reserved.
Reproductions in whole or in part without express written permission of Sargent Manufacturing Company is prohibited.
Outside of Door
Rosette
Spring
Phillips
Screwdriver
Cylinder
Cylinder
Clamp Screw
Fig. 4B
14
1-800-810-WIRE • www.sargentlock.com • A8032G
Fig. 4C
Passport 1000 P1 PoE Mortise Lock
5 Assemble Outside Trim
1. With outside lever horizontal, insert the mounting posts through outside of door and lock body.
Make certain the lever spindle is properly engaged inside the lock body (Fig 5A).
2. On the inside of the door, insert spindle into square hole of mortise lock (Fig 5B).
3. Slide inside adapter and plate assembly over spindle and secure with (2) 8-32 X 5/8" Phillips
oval head and lock washer machine screws.
Note: Ensure that position of set screw hole on inside adapter is oriented to match location of hole in
inside lever handle.
Inside of Door
Outside of Door
Outside Trim
Fig. 5A Detail
Set Screw Hole
Spindle
Spindle
Outside Trim
Fig. 5A
Fig. 5B
1-800-810-WIRE • www.sargentlock.com • A8032G
15
04/30/16
Wire Harness
(From Lock Body)
Copyright © 2016, Sargent Manufacturing Company, an ASSA ABLOY Group company. All rights reserved.
Reproductions in whole or in part without express written permission of Sargent Manufacturing Company is prohibited.
Ground Wire
Passport 1000 P1 PoE Mortise Lock
6 Install Inside Rose and Inside Lever Assembly
1. Place inside rose flush against door surface and rotate first counter-clockwise to seat the threads, then clockwise to securely tighten.
Inside of Door
2. Slide lever onto spindle until fully seated. Be sure handle is horizontal and facing the hinge side of the door.
Push lever onto spindle so minimum gap is visible.
3. Tighten the set screw securely with a T20 Torx® driver.
4. Finish securely tightening (2) #12-24 lock body screws.
5. Before closing the door, test that the lever is functional
and ensure smooth operation of the latchbolt.
Spindle
#12-24 screws
04/30/16
Copyright © 2016, Sargent Manufacturing Company, an ASSA ABLOY Group company. All rights reserved.
Reproductions in whole or in part without express written permission of Sargent Manufacturing Company is prohibited.
Fig. 6
Rose
Set Screw
Inside
Lever
7 Install Thumb Turn
1. Insert thumb turn into preparation hole and engage slot in lock body.
2. Orient mounting plate so screw hole is vertical (aligned with preparation holes).
Inside of Door
3. Secure plate with Phillips screw provided (Fig. 7).
4. Test thumb turn for function by retracting and projecting the deadbolt (7976 and 7977 functions only).
Thumb Turn
Assembly
Fig. 7
16
1-800-810-WIRE • www.sargentlock.com • A8032G
Phillips
screw
Passport 1000 P1 PoE Mortise Lock
8 Install Gasket (Optional) and Outside Escutcheon
Note: Gasket is optional, for non-fire rated doors only.
For non-fire rated door applications, a gasket (Part number 52-0782)
may be used as a weather seal between the escutcheon and the
outside door surface.
1. Peel off adhesive backing and attach to outside escutcheon.
Outside of Door
Escutcheon
Gasket
2. Insert the mounting posts through holes as shown.
3. Feed reader cable through side opening (Fig. 8).
Fig. 8
1. On the inside of the door, position the mounting plate over the indicated holes.
2. Feed reader cable and ground ring terminal
through central opening on mounting plate
(Fig. 9).
3. Route PoE Harness through alternate opening (to the right of the central opening).
4. Route ground ring terminal from lock body
through bottom of mounting plate and
attach to bottom right corner using (1)
#8-32 x 1-7/8” flat head machine screw.
PoE
Harness
5. Insert other three #8-32 x 1-7/8” flat head
machine screws and tighten, fastening the
outside escutcheon to the door (Fig. 9).
IMPORTANT: If the following step is skipped, the product
will not be UL-compliant:
6. Attach two (2) #8 x 3/8” flat head wood screws for
wood doors or (2) #8-32 x 3/8” flat head machine
screws for metal doors (Fig. 9).
Ground
Lugs
Copyright © 2016, Sargent Manufacturing Company, an ASSA ABLOY Group company. All rights reserved.
Reproductions in whole or in part without express written permission of Sargent Manufacturing Company is prohibited.
9 Mounting Plate Assembly
1-800-810-WIRE • www.sargentlock.com • A8032G
17
04/30/16
Fig. 9
Passport 1000 P1 PoE Mortise Lock
10 Installation of Connectors
CAUTION - Do not touch or allow debris to enter connector contacts.
Secure the following connectors to their respective terminals (Fig. 10A):
A. Secure the 10-pin lock body assembly connector.
IMPORTANT: Do not run wires through bottom hole in plate (Fig. 10A) - it will damage wires and
controller connector. Route wires around flange, do not route wires through the flange hole (Fig. 10A).
Secure Mounting Plate
1. Tuck excess cable into wire hole on inside of door.
2. Secure the mounting assembly while ensuring proper
alignment of outside reader and fully tighten the (2) through-
bolts on the inside of the door to secure the reader and plate to the door.
B
Reader
(24-pin)
B. Secure the 24-pin card reader connector (Fig. 10A).
C. Crimp* RJ45 to Cat 5e cable from hinge (Fig. 10B).
A
Ground
*For more detail, refer to section (5) ‘Installation Wiring’,
“A - Frame Harness Installation”.
Lugs
Lock
Body
(10-pin)
Board-to-Board
Connector
04/30/16
Copyright © 2016, Sargent Manufacturing Company, an ASSA ABLOY Group company. All rights reserved.
Reproductions in whole or in part without express written permission of Sargent Manufacturing Company is prohibited.
Fig. 10A
TIA/EIA 568-B Standard Wiring
PIN
1
4 5 6 78
2 3
1
pin
8
8
pin
1
Wire
Pair
Number
1
White/Orange
2
2
Orange
2
3
White/Green
3
4
Blue
1
5
White/Blue
1
6
Green
3
7
White/Brown
4
8
Brown
4
RJ45-M
Cat 5e cable
from hinge
Crimp* to RJ45-M
Connector
Do not confuse pair numbers with pin numbers. A pair number is
used for reference only (e.g.: 10BaseT Ethernet uses pairs 2 & 3). The
pin numbers indicate actual physical locations on the plug and jack.
18
1-800-810-WIRE • www.sargentlock.com • A8032G
C
Fig. 10B
Passport 1000 P1 PoE Mortise Lock
11 Install Inside Module Component Assembly
1. Insert top tabs of controller into slots on mounting plate (Fig. 11A).
2. Ensure proper alignment of board-to-board connectors while pivoting
bottom of controller toward door until tab on bottom snaps securely
into place on mounting plate.
CAUTION: To avoid possible damage to board-to-board connectors, care should be taken when securing controller to mounting
plate. If there is resistance when securing, detach controller to determine cause before re-attaching controller.
Fig. 11A
Fig. 11C
Coin Cell
Pull Tab
3. Connect RJ45 male Connector to female RJ45 on controller board
(Fig. 11B, C).
4. Remove pull tab from its position beneath the coin cell by pulling on
tab in direction of arrows printed on tab (Fig. 11B, C).
1-800-810-WIRE • www.sargentlock.com • A8032G
19
04/30/16
Copyright © 2016, Sargent Manufacturing Company, an ASSA ABLOY Group company. All rights reserved.
Reproductions in whole or in part without express written permission of Sargent Manufacturing Company is prohibited.
Fig. 11B
Passport 1000 P1 PoE Mortise Lock
12 Install Inside Escutcheon
1. Position inside escutcheon as shown (Fig. 12).
Verify that all wires are positioned within the escutcheon to avoid pinching.
Inside of Door
2. Attach escutcheon with (2) #8-32 x 1/2”
T-20 Torx pan head screws.
3. Straighten escutcheon and tighten securely.
DO NOT OVERTIGHTEN.
04/30/16
Copyright © 2016, Sargent Manufacturing Company, an ASSA ABLOY Group company. All rights reserved.
Reproductions in whole or in part without express written permission of Sargent Manufacturing Company is prohibited.
(2) #8-32 x 1/2”
Torx Screws
Fig. 12
13 Attach Outside Front Plate
Attach front plate with (2) #8-32 X 1/4” flat head
screws (Fig. 13).
Inside of Door
(2) #8-32 x 1/4”
Flat Head Screws
Fig. 13
20
1-800-810-WIRE • www.sargentlock.com • A8032G
Passport 1000 P1 PoE Mortise Lock
Operational Check
Copyright © 2016, Sargent Manufacturing Company, an ASSA ABLOY Group company. All rights reserved.
Reproductions in whole or in part without express written permission of Sargent Manufacturing Company is prohibited.
IMPORTANT: Be sure to test functions prior to closing door.
In all cases, perform the following checks:
1. Ensure that inside lever retracts latch.
• For units with cylinders, the following checks apply:
Insert key into cylinder and rotate:
a. There should be no friction against lock case or any other
obstructions. If friction or binding occurs, re-adjust cylinder to
eliminate issues.
b. The key should retract the latch and the key should rotate freely.
c. The key should extend and retract the deadbolt.
• For units without a keypad, add card using LCT software* and test.
• For units with a keypad, add pin and card using LCT software* and test.
2. LED signaling:
• After using a valid credential, a green flash followed by three fast
amber flashes indicates a low power condition.
• Check the input voltage.
• If the input voltage is low, disconnect the lock from the power source
and check the power source voltage. If the power source voltage is
correct, inspect the lock wiring for a possible short.
If the lock loses power, it will flash rapid blue for approximately one minute. Lock will default to programmed fail safe or fail secure.
After that, the lock will no longer be functional.
3. When you have completed the tests, close the door, ensuring latchbolt fully
extends into strike plate without binding.
*Refer to Network and Lock Configuration Tool user manual (WFMN1) for
information on how to configure and program locks.
1-800-810-WIRE • www.sargentlock.com • A8032G
21
04/30/16
8
04/30/16
Copyright © 2016, Sargent Manufacturing Company, an ASSA ABLOY Group company. All rights reserved.
Reproductions in whole or in part without express written permission of Sargent Manufacturing Company is prohibited.
Passport 1000 P1 PoE Mortise Lock
Notes
22
1-800-810-WIRE • www.sargentlock.com • A8032G
SARGENT Manufacturing
100 Sargent Drive
New Haven, CT 06511 USA
800-810-WIRE (9473) • www.sargentlock.com
HID and iCLASS are registered trademarks of HID Global Corporation.
Founded in the early 1800s, SARGENT® is a market leader in locksets, cylinders, door closers, exit devices,
electro-mechanical products and access control systems for new construction, renovation, and replacement applications.
The company’s customer base includes commercial construction, institutional, and industrial markets.
Copyright © 2016, Sargent Manufacturing Company, an ASSA ABLOY Group company. All rights reserved.
Reproduction in whole or in part without the express written permission of Sargent Manufacturing Company is prohibited.
ASSA ABLOY is the global leader in door opening solutions, dedicated to
satisfying end-user needs for security, safety and convenience.
A8032G -04/16
Download PDF
Similar pages