CONTENTS
1.
SAFETY ..................................................................................................................................................... 3
2.
INTRODUCTION ...................................................................................................................................... 3
3.
FEATURES ................................................................................................................................................ 4
4.
REMOTE CONTROL ............................................................................................................................... 5
5.
FRONT PANEL ......................................................................................................................................... 7
6.
REAR PANEL............................................................................................................................................ 7
7.
CONNECTING YOUR SYSTEM.............................................................................................................. 7
8.
BASIC OPERATIONS............................................................................................................................... 9
8.1
8.2
8.3
8.4
8.5
8.6
8.7
8.8
8.9
8.10
8.11
8.12
8.13
8.14
8.15
8.16
8.17
8.18
8.19
8.20
8.21
8.22
8.23
9.
TURN ON STB ........................................................................................................................................... 9
POWER ...................................................................................................................................................... 9
CHANNEL UP/CHANNEL DOWN .................................................................................................................. 9
VOLUME UP/VOLUME DOWN-.................................................................................................................... 9
NUMBER ................................................................................................................................................... 9
MUTE ........................................................................................................................................................ 9
PAUSE ....................................................................................................................................................... 9
RECALL ..................................................................................................................................................... 9
FAVOURITE ............................................................................................................................................... 9
AUDIO ................................................................................................................................................. 10
INFORMATION ...................................................................................................................................... 10
EPG .................................................................................................................................................... 10
TV/RADIO ......................................................................................................................................... 11
CHANNEL LIST ..................................................................................................................................... 11
SLEEP .................................................................................................................................................. 12
PAGE UP/PAGE DOWN .......................................................................................................................... 12
TEXT.................................................................................................................................................. 12
SUBTITLE ............................................................................................................................................. 12
FIND .................................................................................................................................................... 12
ZOOM .................................................................................................................................................. 12
MENU .................................................................................................................................................. 12
VIDEO FORMAT .................................................................................................................................... 12
EXIT .................................................................................................................................................... 13
SERVICE.................................................................................................................................................. 13
9.1
9.2
10.
10.1
10.2
10.3
10.4
10.5
11.
11.1
11.2
11.3
11.4
11.5
11.6
11.7
12.
12.1
ORGANIZING SERVICE .............................................................................................................................. 13
ORGANIZING FAVOURITES ....................................................................................................................... 15
INSTALLATION ..................................................................................................................................... 15
SATELLITE INSTALLATION SATELLITE ................................................................................................... 15
AUTO INSTALLATION ............................................................................................................................ 18
SATELLITE GUIDE ................................................................................................................................ 18
TERRESTRIAL INSTALLATION ................................................................................................................ 18
CABLE INSTALLATION .......................................................................................................................... 19
PREFERENCE......................................................................................................................................... 19
LANGUAGE .......................................................................................................................................... 20
PARENTAL CONTROL ............................................................................................................................ 20
TIME SETTING ...................................................................................................................................... 21
TIMER .................................................................................................................................................. 21
A/V CONTROL ..................................................................................................................................... 22
MISCELLANEOUS SETTINGS .................................................................................................................. 23
OSD SETTING ...................................................................................................................................... 23
SYSTEM................................................................................................................................................... 24
INFORMATION ...................................................................................................................................... 24
1
12.2
DEFAULT SETTING ............................................................................................................................... 24
12.2.1 Default Value:.................................................................................................................................. 24
12.2.2 Delete All Channels: ........................................................................................................................ 25
12.2.3 Save default value ............................................................................................................................ 25
12.3
SOFTWARE UPGRADE ........................................................................................................................... 25
12.4
UPGRADE BY USB ............................................................................................................................... 26
12.5
BACKUP TO USB.................................................................................................................................. 26
13.
CONDITIONAL ACCESS....................................................................................................................... 26
13.1 CA SETTING............................................................................................................................................... 26
14.
USB ........................................................................................................................................................... 27
14.1 FILE LIST ................................................................................................................................................... 27
14.1.1 Record Files........................................................................................................................................ 27
14.1.2 MP3 Files............................................................................................................................................ 27
14.1.3 Image Files....................................................................................................................................... 29
14.1.4 Video ............................................................................................................................................... 30
14.1.5 Software .............................................................................................................................................. 30
14.1.6 All .................................................................................................................................................... 31
14.2 STORAGE INFORMATION ............................................................................................................................. 31
14.3 PVR SETTING............................................................................................................................................. 31
14.4 USB SPEED TEST........................................................................................................................................ 32
14.5 REMOVE USB DEVICE SAFELY! .................................................................................................................. 32
15.
INTERNET............................................................................................................................................... 32
15.1 NETWORK LOCAL SETTING ......................................................................................................................... 32
15.2 HTTP UPGRADE .......................................................................................................................................... 33
15.3 FTP UPGRADE ............................................................................................................................................ 33
15.4 FTP ........................................................................................................................................................... 33
15.5 WEATHER FORECAST .................................................................................................................................. 33
15.6 RSS READER .............................................................................................................................................. 34
15.7 NET MEDIA ................................................................................................................................................ 34
15.7.1 Youtube............................................................................................................................................ 34
15.7.2 Web TV ............................................................................................................................................ 35
15.8 GOOGLE MAPS ........................................................................................................................................... 35
16.
GAME....................................................................................................................................................... 35
16.1 TETRIS ....................................................................................................................................................... 36
16.2 SNAKE ....................................................................................................................................................... 36
16.3 OTHELLO ................................................................................................................................................... 36
17.
NEW FEATURES .................................................................................................................................... 36
17.1 EQUALIZER ................................................................................................................................................ 36
17.2 TIME SHIFT ................................................................................................................................................ 36
17.3 RECORD ..................................................................................................................................................... 37
18.
TROUBLE SHOOTING .......................................................................................................................... 38
19.
SPECIFICATIONS .................................................................................................................................. 39
2
1. SAFETY
This HD Receiver has been manufactured to satisfy the international safety standards. Please read
the following safety precautions carefully.
MAINS SUPPLY: 100 - 240V AC 50/60Hz
OVERLOADING: Do not overload wall outlet, extension cord or adapter as this may result in fire or
electric shock.
LIQUIDS: Keep liquids away from the HD Receiver. The apparatus should not be exposed to dripping
or splashing and no objects filled with liquids, such as vases, shall be placed on the apparatus.
CLEANING: Disconnect the HD Receiver from the wall outlet before cleaning .Use a light damp cloth
(no solvents) to dust the HD Receiver.
VENTILATION: The slots on top of the HD Receiver must be left uncovered to allow proper airflow to
the unit. Do not stand the HD Receiver on soft furnishings or carpets. Do not expose the HD Receiver
to direct sunlight or do not place it near a heater. Do not stack electronic equipment on top of the HD
Receiver.
ATTACHMENTS: Do not use any attachments that are not recommended as these may cause
hazard or damage the HD Receiver.
CONNECTION TO THE SATELLITE DISH LNB: Disconnect the HD Receiver from the mains before
connecting or disconnecting the cable from the satellite dish.
FAILURE TO DO SO CAN DAMAGE THE LNB.
CONNECTION TO THE TV: Disconnect the HD Receiver from the mains before connecting or
disconnecting the cable from the satellite dish.
FAILURE TO DO SO CAN DAMAGE THE TV.
EARTHING: The LNB cable MUST BE EARTHED to the system earth for the satellite dish.
LOCATION: Place the HD Receiver indoors in order not to expose to lightening, rain or sunlight.
2. INTRODUCTION
Thank you for purchasing this HD Receiver.
This HD Receiver is fully compliant with the international DVB standard and thus transmits digital
images, sounds, information guides and teletext directly to your TV through the satellite broadcasting.
Now you can comfortably see and receive digitally transmitted music, news, movie and sports satellite
broadcasts in your office or at your home. You can enjoy interesting games embedded in HD
Receiver.
In service search section, both the automatic service search method and the manual search mode
are provided. Also it supports DiSEqC 1.0, 1.2 and USALS, enabling you to move your antenna in
order to focus preferred satellite. You can save up to 6000 TV and Radio services and work around
with the favourite, Lock, Delete, Move and Sort functions.
The menu is very modern and supports multiple languages. All functions can be carried out using the
remote control. The HD Receiver is easy to use and adaptable for future advances. Please be aware
that new software may change the functions of the HD Receiver.
If you have any difficulties concerning the operation of your HD Receiver, please refer to the relevant
section of this manual, including the ‘Troubleshooting’. This Manual will provide you with useful
information on using this HD Receiver.
3
3. FEATURES






















High Definition STB decoder, Full HD 1080p output via HDMI
CONAX CAS7 embedded
Under 0.5 Watt Standby power consumable
Hybrid tuner for DVB-S2, DVB-T2/T/C
S/PDIF for digital audio or Dolby digital bit stream output
DiSEqC 1.0, 1.1, 1.2 ,USALS and Unicable supported
USB 2.0 Host, USB-WIFI supported
RJ45 for 10Mbps Ethernet interface
Video Decoding: MPEG-4/H.264, MP@ML, MP@HL,MP@HL, MP@4.1, HP@L4.1, XVID, DIVX
Audio Decoding: LPCM,AAC-LC,HE-AAC,MP3,Dolby plus
6000 channels (TV and Radio) programmes
Electronic Programme Guide (EPG)
Subtitle supported
Teletext supported by VBI insertion and software emulation
PVR Ready, Recording and TimeShift
Blind scan and LCN function
Parental lock facility by channel and programme event
RTC(Real-Time-Clock)
Full Picture In Graphic(PIG) function
Multilingual menu text supported
Software upgrade via USB, Http, FTP and RS232
Dimensions 145mm×35mm×110mm
4
4. Remote Control
You can power on/off the receiver, operate on screen
menu, and use a variety of hot key functions.
POWER
To switch your receiver On or into Standby Mode.
MUTE
Used to enable or disable the audio.
NUMERIC KEYS
Used to select channels or enter parameters.
(TV / RADIO)
Receiver switches between TV and Radio mode.
(ZOOM)
Press
key select zoom times, from X1 to X16.
(PREVIOUS)
Return to the previous menu or status.
(AUDIO)
Audio channels setup, to select audio mode; Left, Right, Stereo,
Mono.
TV/STB
Receiver switches between TV and receive mode.
(INFORMATION)
To display channel status or various programme information of
current service.
EPG (Electronic Programme Guide)
Display the Programmers guide on screen when available.
MENU
Displays the Main Menu on the screen, or return to the previous
menu or status.
EXIT
Cancel the user selection and return to the viewing mode from a
menu.
OK
To select menu option, or to update an entry.
<,> KEY
To adjust volume level, or to move cursor left or right in the menu.
^, v KEY
To change channels, or to move cursor up or down in the menu.
P+/PTo move the cursor to the next or previous page
in the menu or channel list.
Red Key
Has different functions per menu.
Teletext (GREEN KEY)
Shows teletext information of the current channel supports.
Subtitle (YELLOW KEY)
Subtitle Display.
UHF
In case your TV is connected through RF Modulator (UHF), select
output channel number between CH21 and CH69 with up and
down key.
(FIND)
Use to prompt find channels sort by character.
TIMER
Press timer key you can setup up the Standby time.
P/N
Press P/N button to switch the display mode among "Auto-> by
native TV<->480i->480p ->576i-> 576P-> 720p-50-> 720p-60->
720P-60-> 1080i-50->1080i-60 ->1080p-50->1080p-60".
SAT
Display satellite list.
FAV (FAVOURITE)
To set receiver to the favourite server mode,
Display the favourite channel.
5
Archive
Press this button to enter the File Manager menu directly.
TMS (Time Shift)
Press this button to display Time Shift info bar.
Play
To play the MP3, JPEG or recording file.
Stop
To stop the Time Shift, recording, or MP3/JPEG player.
PAUSE
Used to select the freeze function.
Press once to freeze the screen picture.
Record
To start recording.
Fast Backward
To start Fast Backward function.
Fast Forward
To start Fast Forward function.
Slow Backward
To start Slow Backward function.
Slow Forward
To start Slow Forward function
6
5. Front panel
Remote Sensor: Detects infrared signal from remote control unit.
POWER Indicator: Shows when the receiver is switched on or in standby mode.
Signal Indicator: When signal is locked, the signal indicator is lit.
Card Slot: One CA Interface for Conax.
USB: USB 2.0 Host, connect to USB hard disk, flash disk or USB wifi dongle. (On the left side of the
receiver)
Display: (LED type) Indicates operating status of receiver.
6. Rear Panel
Please refer to the diagram above for all possible connections of your receiver
Do not connect the unit to the mains socket until all other connections have been connected and checked.
Your configuration can vary depending on model.
LNB IN 13/18V 400mA MAX: This port is to connect the coaxial cable from LNB of your Dish.
RF IN: This port is to connect the coaxial cable from terrestrial antenna or cable.
S/PDIF: Digital Audio interface, connect to AV amplifier S/PDIF input terminal.
HDMI: Audio and Video output socket for TV set with HDMI Input Jack only
ETHERENT: This is used for internet connection.
RS 232: This port is used to connect your receiver and computer through a serial cable.
AV OUT: This RCA connector is used to connect TV using RCA cable.
IR IN: Connect an External IR-Sensor (Infrared).
DC 12V: This is used to connect an external 12V adapter.
7. Connecting Your System
There are two ways to connect the receiver to your existing TV system. We recommend using one of
the following cases for the best result:
1. If you have a high definition television set, you should use a HDMI cable for best result, Plug one
end of the cable into the HDMI socket on the receiver, and the other end into the matching socket on
your television. In this case, you do not have to make audio connections because the HDMI connector
can output stereo audio or Dolby digital audio.
2. Connect one end of RCA cable to the AV mini jack on the back of the receiver and the other end to
an AV mini jack on your TV.
7
Finally connect the coaxial cable from the LNB to the LNB IN jack on the receiver.
With External Audio / Hi-Fi System
To connect any external Audio Hi-Fi system, the receiver has been provided with RCA connector at the
back of the receiver marked with AV OUT.
Connect an RCA cable from the AV OUT jack on the back of the receiver to the LINE, AUX, and SPARE
OR EXTRA input jacks on your Hi-Fi System.
7.1 TV with Motorized System (DiSEqC 1.2)
Connect one end of your coaxial cable to the LNB IN connector on the receiver and the other end to
the REC or Receiver connector on the DiSEqC 1.2 motor.
Connect the coaxial cable from the LNB to the LNB connector on the DiSEqC 1.2 motor.
All our receivers are designed to be DiSEqC 1.0 and DiSEqC 1.2 compatible.
This allows multiple antennas to be connected to the receiver at the same time.
If you have two or more fixed antennas or LNBs, then we recommend you use a DiSEqC 1.0
switch.
Connect the coaxial cable from the first LNB to the LNB 1 or LNB A input connector of the DiSEqC
switch.
Do the same for any other LNBs that you have.
Connect one end of a coaxial cable to the RF output connector of the DiSEqC switch,
Connect the other end to the LNB IN socket on the receiver.
To the digital receiver, you can connect either a single satellite antenna directly or LNB of
multi-feed equipment.
8
8.5
8. Basic Operations
8.1
Number
In full screen, use numeric keys and press [OK] on the
Turn on STB
Remote Control Unit to change channel.
First, press the [Device’s Main Power] to turn on the unit.
When the STB is first used, it will play the first channel
8.6
from the default Channel List. If it’s not the STB’s first
Mute
1 Press [MUTE] key to mute the sound and the
use, STB will play the same channel viewed before
screen will show mute OSD icon.
turning off.
2 Press [MUTE] key again to restore sound.
? Frequently Asked Question
8.7
Q: The power of my STB has been turned on and not
Pause
1 In playing mode, press [Pause] key, the picture will
in Standby mode, but the TV screen shows
be paused, but the sound of the channel will still
nothing:
continue.
A: Make sure the TV set has been set to the correct
video input (not the TV channels). For example, if you
have connected the unit with the Video1 input of the TV
set, the TV set has to be switched to Video1.
2 Press [Pause] key again, the screen’s picture will
skip over to the current playing picture, and the
sound of the channel will play correspondingly.
Q: The power of my STB has been turned on and not
8.8
in Standby mode, but the TV screen shows
Recall
Press [RETURN] key will directly switch to the previous
nothing except one box with “No Signal” image.
channel that you played before current channel.
A: That means the channel, which you select, is no
signal. It could be several causes:
8.9
1 The channel which you select is not in your
Favourite
1 In full screen, press [FAV] key, it will display the
allocate satellite. The simply solution is to change
“Favourite list” window on the left of the screen,
channel.
which you can watch like below.
2 The signal of current TV channel is too weak. You
can try to change channel to other strong signal
channels. If the problems still exist, please consult
your local dealer or other professionals for
technical service.
3 If you use the a Monoblock LNB, and you need
Modify LNB Type
8.2
Power
1 Press [Power] Key can enter the Standby mode
2 In the “Favourite list “window you can move
2 In Standby mode, press [Power] Key again to call
highlight by pressing [Channel Up/Channel Down]
back the unit and go to the previous channel
key to select favourite Channels.
3 User can also disconnect the device’s main power
3 In the " Favourite list " window you can press
to end the Standby mode.
8.3
[Left/Right] key to select favourite groups,
Pressing [P-/P+] keys can implement the “Page
Channel Up/Channel Down
up/Page down” function
In full screen, press [CH+/CH-] to change channel.
8.4
4 Press [Exit] key to exit the current window.
? Frequently Asked Question
Volume Up/Volume Down-
In full screen, press [VOL+/VOL-] to adjust volume.
9
Q: Why does the screen display “No Favourite
Channel”, after pressing [Favourite] key?
A: It is because you haven’t set any channels as
“favourite channel”. Please refer to Favourite
.
8.10 Audio
1 In full screen, press [AUDIO] key to open the
“Audio” window on the screen.
3 Press [Red] key to select the channels by different
group, such as by
Favourite/Satellite/Provider/CAS etc.
4 Press [Green] key to select different display modes
among Now EPG, Next EPG, More and Schedule,
like the following picture:
2 You can modify the audio track by pressing
[Channel Up / Channel Down] key and modify the
audio mode by pressing [Volume Up / Volume
Down] key.
3 Mode: Left/Right/Stereo/Mono
8.11 Information
In full screen, press [INFO] key (press [INFO] key and
[RED] key) to open information screen, the window
shows the parameters of current channel.
8.12 EPG
1 The STB has an Electronic Programme Guide
(EPG) to help you navigate channels through all
the possible viewing options. The EPG supplies
information such as channel listings and
starting/ending times for all available channels.
5 Press [Yellow] key in EPG menu to set a record
2 Press [EPG] key to display EPG screen.
timer or go to Timer List menu.
10
4 Press [Yellow] key to change the current channel’s
6 In EPG menu, when you select one event by
property, such as FAV/ Lock/ Skip/ Delete/
highlighting item, you can set this event to record
Rename.
timer list directly by pressing [REC] button.
7 In EPG menu, press [Exit] to close EPG screen.
8.13 TV/RADIO
In TV mode, pressing [TV/RADIO] key can switch to
Radio mode. In Radio mode, press [TV/RADIO] key to
switch to TV mode.
8.14 Channel List
1 In full screen, press [OK] key to enter “Channel
5 Press [Blue] key to open the “Sort” window like
List”.
below. There are five kinds of sorting ways. You
can press [Channel Up/Channel Down] key to
move highlight and press [OK] key to confirm your
selection.
2 Press [Red] key to change the different group.
which you can watch, like below.
6 The five ways of sorting are:

Default: Sorting by scanning result.

FTA/$: Sort channel through free and
scrambled sequence. Free channels will
appear at the beginning of the channel list
and scrambled channels will appear at the
end of the channel list.
3 Press [Green] key to display details information for

EPG Now
Lock: Accumulate all locked channels and list
in the end of TV Channel List.
11


Name (A-Z): Sort in Alphabetical Order,
1 Press [Find] key in full screen can open the
ignore “$” symbol.
“Find” window like above. You can press
Name (Z-A): Sort in Alphabetical Order,
[Channel Up/Channel Down/Volume
ignore “$” Symbol.
Up/Volume Down] key to move highlight and
7 Press [Up/Down] key to move highlight and press
press [OK] key to input the selected symbol
[OK] key to play the highlighted channel.
or letter into the dialogue.
8 Press [P -/ P +] key to page up and page Down.
2 After input each character, the programme list
9 Press [Exit] key to exit the channel list.
on the left will search the channel according
8.15 Sleep
1
2
to your input and list the matched channel.
This function can set sleep timer. When you set a
3 Move highlight to “OK” and press [OK] key to
sleep timer and the time arrives, the system will
close “Find” window and you can select
automatically enter standby mode.
channel from the channels list directly.
Pressing [SLEEP] key, it will switch the mode
between Sleep Timer Off /10/30/60/90/120
8.20 Zoom
minutes.
1 The [ZOOM] key allows you to magnify a certain
area on the images
8.16 Page Up/Page Down
2 Press [ZOOM] key again, the image will enlarge by
In Channel list, press [Page+/Page-] key to page up and
x1, x2, x4, x6, x8, x12, and x16.
page down the channel list.
3 In “x2 ~ x16” image, use [Up/ Down/ left/ right]
key to move the image center area you want to
8.17 TEXT
1
see.
Press [Green] key in full screen, you can open
4 In zoom mode, press [Exit] to close “Zoom”
teletext page on any channel which has teletext
window.
information.
2
8.21 Menu
If the channel has no teletext information, it will
show “No Teletext Data” on the screen.
Press [MENU] key to open the menu, exit the current
menu to previous menu or close the window.
8.18 Subtitle
1
Press [Yellow] key in full screen, you can switch
8.22 Video Format
subtitle on or off.
2
1 Press [P/N] (white) key under Full Screen playback
If the channel has no subtitle information, it will
for 1st, it will show the current system output video
show “No subtitle Data” on the screen.
resolution, continuously press this key & system
will switch its output video resolution by sequence
8.19 Find
“Auto->480i-> 480P-> 576i-> 576p->
720P-50>720P-60>1080i-50>1080i-60>1080p-50
>1080p-60”.
12
1 You can move highlight by pressing [Up/
8.23 Exit
down] key and [OK] key to select the
Press [EXIT] key to exit the current menu to previous
programmes which you want to edit.
2 You can press [P+/P-] key to implement the
menu or close the window.
Page Up/Page Down function.
9. Service
3 You can use [Red] key to switch different
Group.
When you press [Menu] key to enter menu, there will
4 You can press [Green] key to select the
display the picture like below:
programmes by different select mode.
5 Press colour key can implement the
corresponding function in “Organizing
Services”.
Groups
1 Press [Up/Down] key, you can select the submenu
Organizing services and Organizing favourites. If
Menu Lock is “On”, it will display a dialogue box for
user to input password. The default Password is
“0000”.
2 Press [OK] key to enter the “Organizing Service”.
1 Press [Red] key to open the “Groups” window
Press [Menu] key to go back to main menu.
like above.
9.1 Organizing Service
2 You can press [Up/Down] key to move
highlight and press [OK] key to select group.
When you enter “Organizing Service” menu, there will
3 Press [Menu] key to close “Groups” List.
display the screen like below.
Options
13
Select Lock icon by pressing [Channel
3
Up/Channel Down] key and [OK] key.
Lock the channel by pressing [OK] key.
4
Like the following picture:
1 Press [Green] key to open the “Options”
window like above.
2 You can press [Up/Down] key to move
highlight and press [OK] key to confirm the
select mode.
Delete
3 Press [Menu] key to close “Options” List.
1 Select the channels that you want to edit in
Move
the channel list by pressing [OK] key or other
1 Select the channels that you want to edit in
select mode.
channel list by pressing [OK] key or other
2 Then press [Right] key to move the highlight
select mode.
to right toolbar.
2 Then press [Right] key to move the highlight
3 Select Delete icon by pressing [Channel
to right toolbar.
Up/Channel Down] key and [OK] key.
3 Select Move icon by pressing [Channel
4 Delete the channel by pressing [OK] key.
Up/Channel Down] key and [OK] key.
Skip and rename
4 Move the channels to the position that you
Follow the same way you can set the channel’s
want and press [OK] key to confirm. Like the
Skip or rename for highlighted channel.
following picture:
Find
Lock
1
Select the channels that you want to edit in
channel list by pressing [OK] key or other
select mode.
2
Then press [Right] key to move the highlight
to right toolbar.
14
To remove services from favourites, mark the
desired services by pressing “OK” button in
Favourite List, press
to choose Remove mode
and press “OK” button.
Move
You can reorder and move the service to the
preferred position in Favourite List.
4
Rename
Select the desired FAV List by pressing “FAV”
button, using ,
buttons to choose rename
mode and press “OK” button to display keyboard,
and rename it.
5
1 Press [Find] key can open the “Find” window
like above. You can press [Up/
Group, Options and Find functions
Please refer to the “Organizing Services” part in
this manual.
6
Down/left/right] key to move highlight and
press [OK] key to input the selected symbol
or letter into the dialogue.
10.Installation
2 After input each character, the programme list
on the left will search the channel according
to your input, and list the matched channel.
3 Move highlight to “OK” and press [OK] key to
close “Find” window and you can select
channel from the channels list directly.
9.2 Organizing Favourites
This menu is helpful in adding and deleting
services to and from the favourite group.
1 Press [Up/ down] key to select menu pages
among Service, Installation, Preference,
System, Conditional Access, Internet, USB
and Game.
2 Press [OK] key to enter the “Installation”
menu. If Menu Lock is “On”, it will display a
dialogue box for user to input password. The
default Password is “0000”.
3 Press [Up/ down] key to select menu items.
Press [menu] key to go back to main menu.
FAV List
Choose the FAV List by pressing “FAV” button.
1
10.1 Satellite Installation Satellite
Add
To add services into favourites, mark the desired
services by pressing “OK” button in Service List,
press
to choose Add mode and press “OK”
button.
2
3
1 Satellite: Press [OK] key to enter the Satellite
list.
Remove
15
DiSEqC1.0/ DiSEqC1.1
DiSEqC: You can use [left/right] key to switch
options. There are several options for your
selection:
a)Disable: without DiSEqC.
b)1/2, 2/2: two ports DiSEqC
c) 1/4, 2/4, 3/4, 4/4: 4 ports DiSEqC
d)1/8, 2/8… 8/8: 8 ports DiSEqC
e)1/16, 2/16….16/16: 16 ports DiSEqC
2 Press [Up/Down] key to select satellite. Press
[Page] key to page up or page down.
LNB Type
In this item, press [left/right] key can switch
among “Standard”, “User”, "Unicable" and
“Universal” mode.
For Example: If you use the Unicable LNB, then
you should select “Unicable” option in “LNB Type”
Positioner
and press OK button will display the submenu for
Unicable setting, like the following picture, you can
select the SCIF Channel, SCIF Frequency and
Positioner: in “Positioner” item, you can press [/
Satellite Position according to your LNB type.
Volume Down] key to switch “Off / DiSEqC 1.2 /
USALS” functions.
22K
You can use [left/right] key to switch “ON / off”.
When this item is switched to “ON”, receiver will
receive TV and radio input signal from 22K port. If
the item is switched to “Off”, the receiver will
receive all signals from 0K port.
! Notice
When you choose LNB type “Universal”, you
cannot modify 22K.
Polarity
In “Polarity” item, Press [left/right] key to switch
“Auto / H / V” functions.
TP Edit
When you enter “TP Edit” menu, there will display
the screen like below:
16
NIT Search on/off. After you set up, press
[OK] key to start scanning.
5 In the “TP Scan” item, press [Exit] key to exit
the scanning and save the current
parameters.
Single Scan
1 Press [Red] key, it will display a dialog asking
the scan mode (means you want to scan all
channels or only scan free channels),
1 In “Satellite” item, press [left/right] key to switch
programme type (means you want to scan all
satellite that you want to scan or press [OK] key
channels or only scan TV/Radio channels),
to enter satellite list for selection.
scan type (means preset scan, that is
2 In “TP Index” item, you not only can use
searching the existed TP. Automatic Scan
[left/right] key to select transponder but you can
means blind scan. There is no need for
also use [Add] and [Delete] functions.
existing TP info) and NIT Search on/off. After
 When you press [Green] key, it will display
you set up, press [OK] key to start scanning.
“New TP” in “TP Index” item; you should set
2 Press [White] key into the blind scanning
the parameters of “TP Frequency” and
immediately.
“Symbol Rate” for this new transponder. The
parameters of “TP Frequency” and “Symbol
LNB Power
Rate” can set using numeric keys. The
In “LNB Power” item, you can press [Left/Right] key to
available range are “3000~13450 MHz” and
switch “On/Off” functions.
“1000~45000Ks/s”.
 When you press [Yellow] key, there will show
TP Scan
up a warning message for reminding whether
you want to delete the current transponder or
Press [Green] key to scan current TP’s
programmes.
not. If you select “Yes”, the current
Auto DiSEqC
transponder will be deleted, and the total
account of transponder will reduce 1
Press [Blue] key to run Auto DiSEqC function, it
can find satellite connection ports automatically.
correspondingly.
Blind Scan
 When you press [Blue] key, it will display a
Press [White] key take you directly into blind scan
mode to scan the current satellite.
warning message for reminding whether you
want to delete all transponders or not. If you
Load BBC from USB
select “OK”, all transponders will be deleted.
Press [i] key to load data from usb hdd function.
3 For the existing transponder, you can also
use numeric keys to modify the parameters of
Note: If no USB Hard Disk inserted into the
“TP Frequency” and “Symbol Rate”.
receiver this menu is not available.
4 When you complete your modification, press
Select satellites
[Red] key, it will display a dialog asking the
When you Press [SAT] key, you will see the screen
scan mode, programme type, scan type and
like below:
17
10.3 Satellite Guide
When you enter “Satellite Guide” menu, you will
see the screen like below:
1
You can press [ok] button to select one or more
satellites and then press [red] button; it will show a
dialog asking scan mode, programme type, scan
type and NIT Search on/off. After you set up, press
“Satellite Guide” is used for user to enter local
[OK] key to start scanning.
2
longitude; local latitude and satellite longitude. By
Press [green] button to edit the name and
longitude of the select satellite.
the evaluation from the receiver evaluate the
3
Press [yellow] button to add a new satellite.
antenna azimuth and antenna elevation; user can
4
Press [blue] button to delete one or more satellites
follow this guidance to adjust antenna.
that you have selected.
5
6
You can use numeric keys to input
Press [white] button to move the satellite selected
parameters in “Local Longitude”, “Local
(note: you can only move one satellite).
Latitude” and “Satellite Longitude”.
7
10.2 Auto installation
You can use [Left/Right] key to select east or
west in “Local Longitude” and “Satellite
Longitude”, select north and south in “Local
Latitude”.
8
Moving highlight to “Start” item and press
[OK] key. The lower column on the screen will
calculate the corresponding value
automatically.
9
Orientation means the angle between south
and satellite.
10 Press [MENU] key to draw back to “Main”
“Auto Installation” is a very new and convenient
Menu.
function. It will automatically detect all dishes
connected to this machine and scan the available
10.4 Terrestrial Installation
services belonging to the satellite matched
Press [OK] key to enter the selected item.
according to satellites and transponders data in
current database. You don’t have to input any
parameter of your antenna settings. Just press
“OK” button to enter this “Auto Installation” menu
then it starts scanning and shows you the result at
the end of scan.
18
1 You can select the Bandwidth according different
1 You can select the Scan Mode, Manual Scan or
country.
Blind Scan.
2 You can set the Tuner Power ON/OFF.
2 In “TP Index” item, press [left / right] key to switch
TP that you want to scan.
3 Press [white] key can directly into blind scan
3 For the existed transponder, you also can use
mode to scan the current programmes.
number keys to modify the parameters of
4 Press [Green] key to enter the following menu.
“Frequency” and “Symbol Rate”.
4 You can select the QAM value among 16QAM,
32QAM, 64QAM, 128QAM and 256QAM.
5 You can press [left/right] key to select NIT On/Off
option.
6 When you complete your modification, Press
[Green] key to begin to auto scan.
7 Press [Exit] key to exit the scanning and save the
current parameters.
8
Scan Mode
When you press [red] key, it will display “New TP”
in “TP Index” item; you should set the parameters
of “TP Frequency” and “Symbol Rate” for this new
1 There are two modes. You can scan channel by
transponder.
Channel or by frequency”.
9 When you press [Yellow] key, there will show up a
2 When scan band is UHF and region is “France”,
warning message for reminding whether you will
The range of Ch No. is from 21 to 69. When scan
delete the current transponder or not. If you select
Band is VHF and region is “France”, the range of
“Yes”, the current transponder will be deleted, and
Ch No. is from 6 to 12. (It’s according to region)
the total account of transponder will reduce 1
3 You can press [left/right] key to select LCN On/Off
correspondingly.
option.
10 When you press [Blue] key, there will show up a
4 Press [white] key to enter blind scan menu, or
warning message for reminding whether you will
press [Green] key to enter TP scan menu.
delete all transponders or not. If you select “OK”,
5 Press [Exit] key to exit the scanning.
all transponders will be deleted.
10.5 Cable Installation
11.Preference
Press [OK] key to enter the selected item.
When you enter “Preference” menu, you will see the
screen like below:
19
French, Italian, Spanish, Portuguese, Arabic,
Polish etc.
5 Second Audio: If the channel has no corresponded
audio with “First Audio” but have corresponded
audio with “Second Audio”, system will play the
second audio language as default. If no audio
language corresponds with the “Second Audio”,
then the default language of current channel will
be played automatically. The selections of audio
languages include: English, Russian, German,
In “Preference” menu:
Greek, French, Italian, Spanish, Portuguese,
1 Press [Up/ down] key to select menu items among
Arabic, Polish etc.
Language, Parental Control, Time setting, Timer,
6 Audio Priority: Press [left/right] key to select Dolby
A/V Control, Miscellaneous Settings and OSD
Digital or Language.
Setting.
7 EPG: Press [left/right] key to select EPG language.
2 Press [OK] key to enter the selected item.
8 Subtitle Language: Press [left/right] key can select
subtitle language.
11.1 Language
9 Teletext: You can set teletext language. If the
When you enter “Language” menu, you will see the
streams have this language you can see the
screen like below:
teletext in language you set.
10 Press [MENU] key to draw back from “Language”
menu.
11.2 Parental Control
You can set a password for anyone who wishes to
operate in the “Installation” menu. And you can also set
the password for the locked channels. (How to set the
locked channels please refer to LOCK) Here will show
you how to set and how to revise the password.
1 In “Parental Lock” function, press [OK] key, there
3 Menu Language: press [left/right] key to select
menu languages, the selections of languages
will display a dialogue for you to input the
include: English, Russian, German, Greek,
password. When you input the correct password,
French, Italian, Spanish, Portuguese, Arabic,
you will see a screen like below:
Polish etc.
4 First Audio: Some channels have more than one
audio language for choosing; by this function you
can set the first audio for this channel. If the
playing channel has the same audio as the “First
Audio” you set, system will play this audio
language as default. If the channel hasn’t the
suited audio language, then the system will
compare automatically with second audio
language. The selections of audio languages
2 Menu Lock determines that when user wishes to
include: English, Russian, German, Greek,
enter “Installation” menu, whether user has to
20
input Password or not. If the setting “Menu Lock” is
[Volume Up / Volume Down] keys to move highlight
“ON” this means user have to input password, if
and use numeric keys to input directly.
set to “OFF” means unlocked.
If the current channel provides the correct time
3 Channel Lock determines that when user wishes
information, you will see the current time while you
to play the locked channels, whether user has to
enter “Time” menu. If the current channel doesn’t
input the password or not. If the setting is “ON”,
provide time information, you will have to input the
playing the channels with lock mark will show a
date and time information manually.
 Time Display can control time display on or off when
dialogue on the screen and ask for the password.
If the setting “Channel Lock” is “OFF”, the Lock
full screen play
 Press [MENU] key to draw back from “Local Time
function will be invalid.
4 New Password is used for revising password; you
Setting” Menu.
can input the new password in this item by using
numeric keys directly. After you filled in 4 numbers,
11.4 Timer
the highlight will auto skip to Confirm Password
Press [ok] key to open timer menu.
and ask you to input the new password again. If
 Current time information will display on the first
the password is correct, the screen will show a
column; if the current time is incorrect, please modify
message “Saving Data, Please Wait…” After
the time information in “Time” item.
finished saving and draw back to “System Setup”
 Timer Number: You can press [left/right] keys to set
menu, the revising is complete.
Timer number, and there are 8 timers in total.
5 Press [MENU] key to draw back from the “Parental
 Timer Mode: There are several modes for
Lock” menu.
Timer setting, including Off, Once, Daily, Weekly,
Monthly, and Monthly to Friday and Saturday to
11.3 Time Setting
Sunday.
When you enter “Local Time Setting” menu, you will see
 Timer Service: There are three options for “Timer
the screen like below:
Service”, including “TV Channel” and “Radio
Channel” (timer setting for channel change and
Wakeup/Sleep) and "Record Radio" and "Record
TV" (Timer setting for Record TV or Radio
programme to USB Hard Disk) and Message
(reminding message).
 When you select “Channel” (timer setting for channel
change and Wakeup/Sleep) option in “Timer
Service”, the screen will display like below:
 GMT Usage: This item is for the usage of GMT. You
can press [left/right] keys to switch “On/Off”.
 The “GMT Offset” item is valid only when the setting
“GMT Usage” is “ON”. You can press [Volume Up /
Volume Down] keys to switch “GMT Offset” value
and the range are “-12:00 ~ +12:00” increase each
half hour progressively.
 You can press [left/right] to control Summer time on
or off.
 “Date” and “Time” items are valid only when the
setting “GMT Usage” is “OFF”. You can press
21
i.
Channel: press [OK] key to enter
ix. The message will always display on the
channel list and select channel that you
screen, you can press [Exit] key to close it.
want setting.
ii.
iii.
x. Press [MENU] key to exit the current menu.
Date: use numeric keys to input your
wakeup date.
11.5 A/V Control
On Time: use numeric keys to input your
When you enter “TV System” menu, you will see
wakeup time. Once the time’s up, no matter
the screen like below:
what the system is in standby mode or in
playing mode, the system will automatically
switch to the channel you want and start to
play.
iv.
Duration: After you set a time for “Duration”
item, once the time’s up, the system will
automatically switch to standby mode. If
you do not want this function to work, set
the duration to 00:00.
v.
 Display Mode is for switching the system output
Standby After Finish: You can press
[Left/Right] to control the system is in
video resolution. Highlight this option and press
standby mode or in playing mode after the
left or right key, it will switch video resolution
circularly by the sequence “Auto<-> by native
record stopped.

TV<-> 480i<-> 480P<-> 576i<-> 576p<->
When you select “Message” (reminding
720P<->1080i-50<->1080i-60<->1080P-50<->108
message) option in “Timer Service”, the screen
0p-60”.
will display like below:
 This effect is equal to press [P/N] Key under Full
Screen and their last setting saving will be efficient
for each other. By Source means system will set
the video output resolution according to the current
programme it’s playing, different resolution
programmes switching perhaps will make TV
screen flicker. By Native TV means system will be
according to the HDMI TV’s max supported
resolution to set its resolution, if system is not
connected to a HMDI TV, it will set resolution to
vi.
Wakeup Message: press [left/right] key to
default.
 Aspect Mode is for switching the screen aspect
select reminding message as Birthday,
ratio mode. Now we provide following options: 4:3
Anniversary and General.
PS / 4:3 LB / 16:9/Auto. You can press [Left/Right]
vii. Date, you can use numeric keys to input
key to select each mode circularly. 16:9 will
your wakeup date.
provide user pillar box mode, it means user use
viii. On Time: use numeric keys to input your
16:9 TV to display but need to see a 4:3 full display
wakeup time. Once the time’s up, no matter
picture. System will force press wide screen
what the system is in standby mode or in
picture to be narrow and there are black bands on
playing mode, the system will automatically
left and right side. Auto means system won’t do
display a reminding message.
any aspect ration translation, 16:9 picture source
22
will be good display on a 16:9 TV but will be too
3
Auto Power Down: You can press [Left/Right] key
narrow on a 4:3 TV, and 4:3 picture source will be
to select the time or “Off”, if you select time,
too wide in a 16:9 TV but will be good display in a
duration this time if no any operation on receiver, it
will go to standby mode.
4:3 TV.
4 Standby mode: if set to “Real”, Press power key
 Video Output: Press [Left/Right] to select CVBS or
receiver will be in real standby status, the
RGB.
consumption wills less than 0.5 Watt. If it’s set to
 Digital Audio Out is for setting both SPDIF and
HDMI’s digital audio output mode, it has options
“Fake”, Press power key, receiver will be in fake
LPCM Out, Auto, You can press [Left/Right] Key to
standby status.
5
select each mode circularly. LPCM Out means
Press [MENU] key to draw back from
“Miscellaneous Settings” Menu.
system will decode no matter AC3 or PCM audio
track data to be LPCM, digital audio decoder or
HDMI TV will get LPCM digital audio data. Auto
11.7 OSD Setting
means system will detect which the connected
When you enter the “OSD Setting” menu, you will
HDMI TV can decode and then output that data. If
see a screen like below:
HDMI TV can decode AC3, system just output
RAW data, if HDMI TV can decode LPCM only;
system will just decode AC3 or LPCM to be LPCM
and then output.
 Press [MENU] key to draw back from “AV
System” menu.
11.6 Miscellaneous Settings
When you enter “Miscellaneous Settings” menu,
you will see a screen like below:
1 OSD Timeout: When you switch channels in
full screen, there will display information
about current channel on the lower part of the
screen. Regarding the duration this
information is displayed on the screen, you
can press [left/right] key to set the time. The
range of the duration is “1 second ~
10seconds”.
2 OSD Position: control display position of the
1
Channel list num: This item provides below
info bar in full screen mode. You can choose
options: 1/2/3, you can press [Left/Right] key to
“bottom” or “top”.
3 OSD Transparency: Besides the setting of
select each mode circularly.
2
Subtitle Auto: You can press [Left/Right] key to
“OSD Menu Style”, you also can set the
select “On” or “Off”. If the current channel has
transparency of OSD. You can press [left/right]
subtitle information, it will be showed automatically
key to select the value. There are 5 levels of
while this function is “ON”, if this function is “OFF”,
transparency, 10%, 20%, 30%, and 40% and
you need turn on the subtitle manually by pressing
“OFF” (means no transparency function).
[SUBTITLE] key.
23
VERSION,LOADER VERSION,LATEST
4 Brightness/Contrast/ Saturation: You can
UPDATE,STB SN,STB ID,CHIP ID.
adjust the parameter about the Video image
2 Press [MENU] key to draw back to “Information”
by using the [OK] button or press [left/right]
menu.
key, the default value is Level 10.
5 Load Default OSD Setting: If you are not
12.2 Default Setting
satisfied with your setting, you can highlight
this item and press [OK] key to reset
parameters as default value.
6 Press [MENU] key to draw back from the
“OSD Setting” menu.
12.System
When you enter “System” menu, you will see a
screen like below:
12.2.1 Default Value:
In “System” menu:
1
Press [Up/Down] key to select menu pages
among Information, Default Setting, Software
When you press [OK] key in the “Default
Upgrade, Upgrade By USB, Backup to USB
Setting” item:
1 There will display a dialogue box for you to
2 Press [OK] key to enter the selected item.
enter the password, the default password is
“0000”.
12.1 Information
2 After you input the correct password, there
will show a warning message asking you
“The operation will load default and erase all
the channels that user added, continue?”.
3 If you select “YES”, all the revised
parameters of the receiver will reset to
default value. Please use this function
carefully.
4 In step 1 and step 2, press[Exit]key to draw
1 When you enter “Information” menu, you will
back from this item without saving.
see a screen like above. The screen
displays :MODEL ID,S/W VERSION,H/W
24
12.2.2 Delete All Channels:
When you press [OK] key in the “Delete All
1 We offer this function for user to connect
Channel” item, it will display a dialogue box asking
receiver (Master) to the other receiver (Slave)
you to confirm to delete all channel. If you select
via serial interface.Connect master receiver to
“YES”, all channels will be deleted
slave receiver via serial interface. Enter
12.2.3 Save default value
“Software Upgrade” menu in master receiver
and press[Volume Up/Volume Down]keys to
switch upgrade mode: All SW+bootloader /All
SW+Channel list/Software(no channel
list)/Channel list.
2 Moving highlight to “Start” on master reeciver
and press [OK] key to start upgrade.
3 Turn on slave receiver and it needn’t operate
any setting.
4 Press [MENU]key to draw back.
When you press [OK] key in the “Save default
value” item,there will show a message to ask
Upgrade By Satellite:
you"Do you want to set current database as
default data?".If you select “YES”,it will set the
current data as default data.
12.3 Software Upgrade
This function can upgrade the software through signal
lines from the satellite
1 Select the satellite and TP or input the TP value and
download PID, these parameters you can get from
your provider.
2 Then move the highlight to the start button and press
Upgrade by RS232:
[OK] button to start upgrade.
25
12.4 Upgrade By USB
13.Conditional Access
In this menu you can upgrade the software from USB
conveniently, Press “Left/Right” button select
13.1 CA Setting
USB; press ' OK ' button to enter.
We provide one CA slots for users use. Receiver
In this menu you can select the Upgrade Mode among
has build in smart card module with CONAX
Software(No channel list), Channel list, All
SW+bootloader and All SW+Channel list, and you can
system. By using cards in this system provided by
select the appropriate upgrade file on "Upgrade File"
operators, it is possible to watch many scrambled
item. After you select the "Upgrade Mode" and "Upgrade
channels coded in this system. This menu shows
File", press ' OK ' button on "Start" item, the receiver can
detailed information about card inserted into card
upgrade automaticlly
reader module. It allows inserted according to help
.
Note:
messages visible on the bottom of the screen.
You must put the upgrade file on the /ROOT
DIRECTORY of the USB storage.
12.5
Backup to USB
In this menu ,you can dump the software to the
USB equipment
1 In "Backup file",you can press [OK] key to edit
the file name.; Press “Left/Right” button select
Note:
USB A;
All information showed in this menu and submenus
2 In "Backup to USB", you can press [OK] to start
are coming from inserted card. In case anything is
backup software .
wrong, there could be a problem with the card.
After inserting the card correctly at any time, a
26
message-box will show on the screen with
14.1.1 Record Files
message about detecting the card, in "card info"
menu all available information will be displayed.
You can press [left/right] key to set the message
display time.
14.USB
If you enter the "USB" Menu, you will see the
picture like below:
In this menu you can playback the recorded files,
Note: If no USB Hard Disk inserted into the
and you can press [Red] key to rename the file, or
receiver this menu is not available.
press [Green] key to lock the file, or press [Yellow]
key to delete the file.
You can press [1] key to adjust the volume while
you preview the record file on top of the right
corner and you can press
to enable or disable
the audio.
14.1.2 MP3 Files
14.1 File List
In this menu you can select the file list from USB A.
Press [ok] button to enter the File list. you can
check the files and folders of the USB storage and
you can play MP3 and JPEG files.
In this menu you can select the MP3 file to play by
pressing [OK] key or [PLAY] key. Also you can set
the play list..
[Red] key: Show play list as the picture bellow:

27
Red Key:
Move the selected file by pressing Red key and

[UP] [DOWN] key.
To delete the file or folder from the disk.

Green Key:

Delete the selected file by pressing Green key.

Yellow Key
Blue Key
To create a new folder in the disk.
Yellow Key:
Delete all files by pressing Yellow Key, but there
Press [EXIT] key to draw back to ‘EDIT’ MENU.
will display a dialog box asking “Delete All” before
[White] key:
practical operation, if user selects “Yes”, all files
To set the Repeat mode of the MP3 player.
will be deleted, and the Play list window will close.

Press OK button to play file.
[Green] key:
All the MP3 files in current directory are added into
MP3 play list by pressing [Green] key, and will
display “
”beside the MP3 files.
After begin playing MP3, it will show the MP3 play
window.
Press “PAUSE” button to pause. Press “PLAY”
button to play. Press “STOP” button to stop and
time return to 00:00.
Press “PREV” button to jump to the beginning of
the file list if play is over 3 seconds; or jump to
previous file if play less than 3 seconds.
[Yellow] key:
Press “NEXT” button to go to the next file.
To edit the files or folders in the USB storage press
this button, you can see the picture like the below.
Press “FORWARD” button to go forward 4S.
Press “BACKWARD” button to go back 4S.
Jump to beginning or end if less than 4S to the
beginning or end of music file.
Switch to the next file or stop playing by the repeat
mode when play is over on the current file.
[0] key: To sort the file list by different order.

Red Key
To rename the file or folder.

Green Key
To copy the file or folder to another folder.
28
In this menu to user can adjust settings for JPEG
player.
[FAV] key: To add mp3 or jpeg to play list.
14.1.3
Image Files
[0] Key:
Sort the file list by pressing [0] button.
[Red] Key:
Show file play list. There will display “The type of
playlist does not exist” if there are no files.
Image view operation
Please see the below image operation menu if
Image function is selected.
Press 'OK' button on the selected files to play the
files.

Red Key:
Move the selected file by pressing Red key and
[UP] [DOWN] key.
You can preview the picture at the top right corner

if the scroll bar is on the picture files (JPG, BMP),
Delete the selected file by pressing Green key.
and show the logo when at MP3 file.

Move scroll bar when press up/down key, page up
Press Yellow Key to delete all image files in play
or down by page key.
list, but system will remind you “Delete All” before
Go into sub-directory when press ok key in the file
directory, play the selected file when scroll bar is
on the file, automatic return to USB menu after
play is over.
practical operation, if you select “Yes”, all files will
Green Key:
Yellow Key:
be deleted and Play list window will be closed.

Press OK button to play file
[Green] key:
White key:
29
All the Image files in current directory are added
You can see the video files in this menu, it can
into Image play list by pressing Green key, and will
support .mpeg and .ts format file.and press [play]
display “
key to preview the video at the top right corner.
”beside the Image files, like below.
You can press [1] key to adjust the volume while
you preview the video file,press [0]key to sort the
file list. and press
to enable or disable the
audio

Yellow key
To edit the files or folders. Includes rename, copy,
delete and create folder functions. You can press
[Left/Right] key to previous menu.
[Yellow] key:
14.1.5 Software
To edit the files or folders in the USB storage like
in MP3 menu. Includes rename, copy, delete and
create folder function. You can press [Left/Right]
key to previous menu.
[Blue] key
To preview the images press this key, you can see
the picture like below.
If software exists in current directory, you can
press [Green] key to upgrade like below.
14.1.4 Video
30
14.1.6
If you want to change the path for recording files
All
and timeshift files, press “blue” button to enter the
DVR Set menu, then press OK button to set the
path on current select disc.
14.3 PVR Setting
You can preview all files in this menu.
14.2 Storage Information
Press "OK" button to enter the HDD Information
menu like the below picture, in this menu you can
see detailed information about the HDD.

Time Shift:
ON: Enable the Time Shift function.
OFF: Disable the Time Shift function.

Timeshift to Record
ON: Means when you press the "
" Button
to record the programme; it will merge the
Timeshift files and the record files.
OFF: Means when you record the
programme, it will start when you press "
If you want to format the HDD, press "yellow"
"
button, not include the Timeshift files.
button to enter Format menu, then select the File
Record Type
System between "FAT" and "NTFS", Press "OK"
You can select the record type by pressing
Button to confirm.
[left/right] key.

HDD Sleep Time
You can select the HDD sleep time by
pressing [left/right] key. When the HDD is not
being used, it will sleep after the time you
select.

Jump Time
You can select the jump time by pressing
[left/right] key.
Note:
If you format the HDD, all the files including MP3,
JPEG and the recorded files will be deleted from
the HDD.
31
14.4 USB Speed Test
15.1 Network Local Setting
1. Select your Network Type as Wired or Wireless,
if you select Wireless, you can configure Wi-Fi
(wireless) by the following steps:
a. Select Wireless on Default Network Type item.
In "USB Speed Test" Menu you can see the
Standard speed and your USB hard disk speed,
according to this information you can know what
operation your disk can support.
b. Press [red] button & the wireless LAN network
list will appear select you Wi-Fi network and
press [ok] button, then input password.
14.5 Remove USB Device safely!
Use this menu to remove the USB Device safely.
15.Internet
If you enter the "Internet" Menu, you will see the
picture like the below:
 
c. Press [OK] button on Connect item to start
connecting.
2. In this menu you may assign a dynamic IP
address to the digital receiver. To do so, select
DHCP On.
3. If you have a static IP address, unselect the
DHCP Enable, then the IP Address, Subnet Mask,
Gateway and DNS options become enabled. You
have to set these options according to your IP
address.
You can download new software from the network
via LAN port.
32
15.2 Http Upgrade
15.4 FTP
When connected to the Internet, the receiver can
When connected to the Internet, receiver can
manually or automatically make software update
download files, such as software, MP3 or Image
from file from server. If you get the “Load http upgrade
files from FTP server.
[ail].txt” file, you can press [white] key to update the
Note:
upgrade files URL from USB.
This function depends on connection with external
Note:
server. In case of no any files on server, this
This function depends on connection with external
function will not work.
server. In case of no software on server, this
function will not work.
15.5 Weather Forecast
15.3 FTP Upgrade
In this menu you can see the weather forecast,
press [Green] key to add city.
When connected to the Internet, receiver can
make software update from file from FTP server. If
you get the “Load FTP upgrade [ail].txt” file, you can
press [white] key to update the upgrade files URL from
USB.
Note:
This function depends on connection with external
server. In case of no software on server, this
function will not work.
 Red key
To update the weather forecast to the latest.
 Green key
To add new city use this menu. You can add upto
5 cities.
33
 Yellow key
To delete current city.
 Blue key
To switch temperature mode.
 White key
Press ok button to see detailed infomation like
below.
To update weather forecast city list from USB
15.6 RSS Reader
15.7 Net Media
When you enter “Net media” menu, you will see the
screen like below:
In this menu you can see the news
 Red key
To update the news to the latest.
 Green key
To add new channels,you can input a new
website. You can add upto 10 channels.
In “Net media” menu:
1
Press [Up/Down] key, you can select the
submenu YouTube and WebTV.
2
Press [OK] key to enter the selected item.
15.7.1 Youtube
This menu is some internet applications.
"YouTube" can play stream media from
"www.youtube.com". When you enter this menu,
you will see a screen like below:
 Yellow key
To delete current channel.
 Blue key
To edit current channel information. You can edit
channel name and channel Url.
 White key
To update RSS the channels from USB.
34
1.
In this menu you can select your favourite channel
to view, press [OK] key play in full screen, you can
press [up / down] key to change channels, and
press [left / right] key or [volume + / -] key to adjust
volume level.
2.
Press [green] key to add channel URL;
3.
Press [Blue] key to edit channel URL;
4.
Press [yellow] key to delete channel URL.
5.
If you get the “WebTV List.txt” file, you can add
more channels and press [white] key to update the
1. Press [up/down] key to move highlight.
channels from USB.
2. Press [OK] key on one item, it will play
Note:
pertinent video. The video will show on top left
You must put the “WebTV List.txt” file on the
corner. Press [OK] again the video will play in
/ROOT DIRECTORY of the USB storage.
full screen.
15.8 Google Maps
3. Press [VOL+/VOL-] to control volume.
4. Press [pause] key to pause video, or press
Inside the menu can browse Google Maps
[stop] key to stop play.
5. Press [red] key to display the featured video.
6. Press [green] key to sort by site and duration.
The site has Germany, worldwide, Poland and so
on. Duration has all time, this week, and this month
and so on.
7. Press [yellow] key to switch group. These are
game, news, tech, move and so on.
8. Press [white] key to display the related videos.
9. Press FIND [ ] key in full screen to open the "Find”
window. You can press [,,,] keys to move
highlight and press [ok] key to input the letters .Then
press [red] key to find.
16.Game
15.7.2 Web TV
When you enter to “Web TV” menu, you will see a
screen like below:
When you enter “Game” menu, you will see three
Games including Tetris, Snake and Othello.
Basic operation statement:
35

16.1 Tetris
[UP/ Down/left/right] use these arrow
keys to guide chessman.
a) Move highlight to “Setup” and press
[left/right] key to select the game level

[OK] set chessman.
(speed).

[Exit] Quit game and draw back to
“Game” menu.
b) Move highlight to “Start” and press [OK] key
to start the game.
17.New Features
c) Move highlight to [Cancel] key and press
[OK] key to draw back from the game.
17.1 Equalizer
d) Start the game:
When listening to a Radio programme, it will
 [left/right] Move shape left or right
display the music spectrum graphic on TV Screen.
 “Channel Up” Rotate clockwise
 “Channel Down” Faster drop
 [OK] Pause/Play the game
 [Exit] Quit game and draw back to
“Game” menu.
16.2 Snake
a) Move highlight to “Setup” and press
[Volume Up/Volume Down] key to select
the game level (speed).
17.2 Time Shift
b) Move highlight to “Start” and press [OK] key
If you connect the USB HDD, and enable the Time
to start the game.
c)
Shift function in the menu "Main Menu/ Record/
Move highlight to[Cancel]key and
PVR Setting/Time Shift",
Press [OK] key to draw back from the
It will start the Time Shift function automatically
game.
after you switch the programme, and when you
d) Start the game:
press the "Tms" button the Time Shift info bar will
 [UP/ Down/left/right] use these arrow
display as the following picture:
keys to guide the snake.
 [OK] Pause/Play game
 [Exit] Quit game and draw back to
“Game” menu.
16.3 Othello
a) Move highlight to “Setup” and press
[left/right] keys to select the game level
(degree of difficulty).
b) Move highlight to “Start” and press [OK]
Key to start the game.
1
You can press "
2
You can press "
" button to pause the video.
" or "
" button to fast
Backward or Fast Forward.
c) Move highlight to [Cancel] key and press
3
[OK] key to draw back from the game.
You can press "
" or "
" button to slow
Backward or Slow Forward.
d) Start the game:
36
4
Press “left" or "right" button to jump to different
position, then press "OK" button to confirm.
5
Press " " button to exit the playback.
17.3 Record
If you connect the USB HDD.
You can press "
" button to start record function,
as following picture:

Press "
" button to display the record info
bar when you recording.

Press "

You can press "

You can press "
" button again to set record time.
" button to pause the video.
" or "
" button to fast
Backward or Fast Forward.

You can press "
" or "
" button to slow
Backward or Slow Forward.

Press “left" or "right" button to jump to different
position, then press "OK" button to confirm.

Press " " button to stop the recording.
37
18.Trouble Shooting
If you suspect there is a fault with your receiver, please check the following trouble shooting guide
Before calling an authorized service agent.
Warning! Under no circumstances attempt to repair the receiver yourself. Tampering with the receiver may
result in fatal electric shock and will invalidate your warranty.
Symptom
Possible cause
Settings you made in the menu
have not change
The receiver lost power before being able to enter into standby mode
Some of the Settings saved by user can be deleted partly or fully
No signal
The level of signal is too weak
LNB is out of order
The cable from the LNB or Terrestrial antenna is incorrectly
Connected (short circuit or open circuit)
The position of dish is aligned incorrectly
Receiver is on, but no picture or
sound except the following
messages (NO TV programme)
Receiver not responding to
remote control unit
Poor picture Quality
No sound
Channel is not available
Channel is scrambled
RCU batteries are dead or inserted incorrectly
The RCU is pointing toward wrong direction
The level of Signal strength is too low
The cable is connected incorrectly
The Volume level is too low
Mute function is active
No display on the VFD Display
Panel
The power cord is not plugged in correctly.
No picture on the screen
Receiver is in Standby mode
RCA Jack or cable is not connected firmly to the video output port of
your television
Incorrect channel or video output is selected on your television
Brightness level of your TV set is incorrectly defined
38
19.Specifications
SYSTEM RESOURCES
Main Processor
594MHz based CPU
Flash Memory
64 Mbits
DDR SDRAM
1024 Mbits
Tuner/Front-end(Optional)
Tuner Type
DVB-S / DVB-S2
Input Connector
F-type, Connector, Female
Signal Level
-65 to -25 dBm
LNB Power & Polarization
Vertical: +13V
Horizontal: +18V
Current: Max. 400mA
Overload Protection
22KHz Tone
Frequency: 22±1KHz
DiSEqC Control
Amplitude: 0.6±0.2V
Version 1.0, 1.1 1.2, USALS Available, Unicable
Demodulation
QPSK, 8PSK
Input Symbol Rate
1-45 Mbps, Convolution Code Rate
Forward Error Correction
DVB-S 1/2, 2/3, 3/4 5/6, 7/8
(FEC)
DVB-S2 1/2, 3/5 , 2/3, 3/4 ,4/5 , 5/6, 8/9 , 9/10
Tuner Type
DVB-T2/T/C
Input Connector
IEC-type, Connector, Female
Frequency Range
48MHz~862MHz
Input Level
-80.0dBm and -20.0dBm
Active ANT Power
DC 5V at max 75 mA, Overload protection
Bandwidth
VHF/UHF: 1.7MHZ,6MHz, 7MHz, 8MHz
Demodulation
COFDM
Transmission mode(FFT)
1k, 2k, 4k, 8k normal and extended, 16k normal and extended, 32k
normal and extended.
Constellations
QPSK, 16-QAM, 64-QAM, 256-QAM
Both rotated and non-rotated
Guard intervals
1/4, 19/256, 1/8, 19/128, 1/16, 1/32, 1/128
Code rate
DVB-T: Viterbi + Reed Solomon 1/2, 2/3, 3/4, 5/6, 7/8.
DVB-T2: LPDC + BCH 1/2, 3/5, 2/3, 3/4, 5/6.
Scattered Pilot Pattern
PP1, PP2, PP3, PP4, PP5, PP6, PP7, PP8
DVB-T2 Input Profiles
Input Mode A-Signal PLP, input Mode B-Multiple PLPs(Common
PLP, Type 1 and 2 up to the maximum allowed figure 255)
39
POWER SUPPLY
Input Voltage
DC 12V/2A
Power Consumption
15W MAX
MPEG TS A/V Decoding
Transport Stream
MPEG-2, H.264
Input Rate
Max.120Mbit/s
Aspect Radio
4:3, 16:9, Letter Box
Video Decoding
MPEG-2, MP@ML, MPEG-4 part 10/H264
Video Resolution
720*480P/I, 720*576P/I, 1280*720p,1920*1080i, 1920*1080P
Audio Decoding
MEPG-1 layer I/II, Mpeg2 layerII, Dolby digital
Audio Mode
Left / Right / Stereo/ Mono
Sampling Rate
32, 44.1 and 48KHz
A/V & DATA INPUT/OUTPUT
AV OUT(3.5MM Earphone
Video CVBS output
Jack)
Audio L/R output
IR(3.5MM Earphone Jack)
38Khz
RS-232C(3.5MM Earphone
Transfer rate 115.2Kbps
Jack)
9 pin D-sub Type
LAN
10M
USB
One USB 2.0 slot Compatible
HDMI
VER1.3
Type A
PHYSICAL SPECIFICATION
Size[L*W*H]
145mmX35mmX110mm
Net Weight
0.23KG
Operation Temperature
0℃~+45℃
Storage Temperature
-10℃~+70℃
Storage Humidity
5%~95% RH (Non-Condensing)
Specifications are subject to change without further notice.
The manufacturer does not assume any responsibility regarding any errors or mistakes in printing.
Please note that new software may change the features of the receiver.
The manufacturer holds the rights of changes without any further notice.
The image shown here is indicative only. The actual product may differ.
40
Download PDF
Similar pages