Always there to help you
Register your product and get support at
www.philips.com/support
Question?
Contact
Philips
User manual
BTB7150
Contents
1Important
2
Safety2
2 Your micro system
4
Introduction4
What's in the box
4
Overview of the main unit
5
Overview of the remote control
6
3 Get started
Connect speakers
Connect FM antenna
Connect power
Prepare the remote control
Demonstrate the features
Set clock
Turn on
9
9
9
10
10
10
10
5 Listen to the radio
12
12
14
6 Other features
15
15
15
15
15
Listen to DAB+ radio
Listen to FM radio
Set the alarm timer
Set the sleep timer
Listen to an external device
Listen through a headphone
16
16
17
17
17
8Troubleshooting
18
9Notice
19
Specifications
USB playability information
Supported MP3 disc formats
RDS program types
7
7
7
7
8
8
8
8
4Play
Play from disc
Play from USB
Control play
Skip to a track
Program tracks
Play from Bluetooth-enabled devices
7 Product information
EN
1
1Important
•
•
Safety
This 'bolt of lightning' indicates uninsulated
material within the device may cause an
electrical shock. For the safety of everyone in
your household, please do not remove the
covering.
The 'exclamation mark' calls attention to
features for which you should read the enclosed
literature closely to prevent operating and
maintenance problems.
WARNING: To reduce the risk of fire or electric
shock, the device should not be exposed to rain
or moisture and objects filled with liquids, such
as vases, should not be placed on the device.
CAUTION: To prevent electric shock, fully
insert the plug. (For regions with polarized
plugs: To prevent electric shock, match wide
blade to wide slot.)
•
•
•
•
Important Safety Instructions
•
•
•
•
•
•
2
Follow all instructions.
Heed all warnings.
Do not use this device near water.
Clean only with dry cloth.
Do not block any ventilation openings.
Install in accordance with the
manufacturer's instructions.
Do not install near any heat sources such
as radiators, heat registers, stoves, or other
devices (including amplifiers) that produce
heat.
EN
•
•
Protect the power cord from being
walked on or pinched, particularly at plugs,
convenience receptacles, and the point
where they exit from the device.
Only use attachments/accessories specified
by the manufacturer.
Use only with the cart, stand, tripod,
bracket, or table specified by the
manufacturer or sold with the device.
When a cart is used, use caution when
moving the cart/device combination to
avoid injury from tip-over.
Unplug this device during lightning storms
or when unused for long periods of time.
Refer all servicing to qualified service
personnel. Servicing is required when the
device has been damaged in any way, such
as power-supply cord or plug is damaged,
liquid has been spilled or objects have
fallen into the device, the device has been
exposed to rain or moisture, does not
operate normally, or has been dropped.
Battery usage CAUTION - To prevent
battery leakage which may result in bodily
injury, property damage, or damage to the
unit:
• Install all batteries correctly, + and - as
marked on the unit.
• Do not mix batteries (old and new or
carbon and alkaline, etc.).
• Batteries (packed or installed) shall not
be exposed to excessive heat such as
sunshine, fire or the like.
• Remove batteries when the unit is not
used for a long time.
The device shall not be exposed to
dripping or splashing.
Do not place any sources of danger on
the device (e.g. liquid filled objects, lighted
candles).
•
Where the MAINS plug or an appliance
coupler is used as the disconnect device,
the disconnect device shall remain readily
operable.
Warning
•• Never remove the casing of this device.
•• Never lubricate any part of this device.
•• Never place this device on other electrical equipment.
•• Keep this device away from direct sunlight, naked
flames or heat.
•• Never look into the laser beam inside this device.
•• Ensure that you always have easy access to the power
cord, plug, or adaptor to disconnect this device from
the power.
Hearing safety
Caution
•• To prevent possible hearing damage, do not listen at
high volume levels for long periods.
To establish a safe volume level:
• Set your volume control at a low setting.
• Slowly increase the sound until you can
hear it comfortably and clearly, without
distortion.
Listen for reasonable periods of time:
• Prolonged exposure to sound, even
at normally 'safe' levels, can also cause
hearing loss.
• Be sure to use your equipment reasonably
and take appropriate breaks.
Be sure to observe the following guidelines
when using your headphones.
• Listen at reasonable volumes for
reasonable periods of time.
• Be careful not to adjust the volume as your
hearing adapts.
• Do not turn up the volume so high that
you can’t hear what’s around you.
• You should use caution or temporarily
discontinue use in potentially hazardous
situations.
• Do not use headphones while operating
a motorized vehicle, cycling, skateboarding,
etc.; it may create a traffic hazard and is
illegal in many areas.
Listen at a moderate volume:
• Using headphones at a high volume can
impair your hearing. This product can
produce sounds in decibel ranges that may
cause hearing loss for a normal person,
even for exposure less than a minute. The
higher decibel ranges are offered for those
that may have already experienced some
hearing loss.
• Sound can be deceiving. Over time your
hearing 'comfort level' adapts to higher
volumes of sound. So after prolonged
listening, what sounds 'normal' can actually
be loud and harmful to your hearing. To
guard against this, set your volume to a safe
level before your hearing adapts and leave
it there.
EN
3
2 Your micro
system
Congratulations on your purchase, and
welcome to Philips! To fully benefit from the
support that Philips offers, register your product
at www.philips.com/welcome.
Before using your product, read all
accompanying safety information.
To download the full user manual, visit
www.philips.com/support.
What's in the box
Check and identify the contents of your
package:
• Main unit
• 2 x speakers
• 2 x speaker cables
• 2 x AC power cords
• 1 x aerial
• Remote control (with one AAA battery)
• Short user manual
• Safety and notice
Introduction
With this unit, you can:
• enjoy audio from discs, Bluetooth-enabled
devices, USB storage devices, or other
external devices;
• listen to Digital Audio Broadcasting (DAB)
or FM radio stations.
You can enrich sound output with below
sound effects:
• TREBLE
• BASS
The unit supports these media formats:
4
EN
INFO
RDS
SOURCE
PRESET/ALBUM
SCAN
Always there to help you
Register your product and get support at
www.philips.com/welcome
Question?
Contact
Philips
MENU
VOL
DIM
SHUFFLE
MUTE
REPEAT
PROG
TIMER
SOUND
CLOCK
SLEEP
Overview of the main unit
n
a
m
b
l
k
c
j
d
i
e
f
h
g
a
h
• Turn the unit on or off.
• Switch to standby mode or Eco
standby mode.
• Bluetooth indicator.
b Disc compartment
c
• USB socket.
d AUDIO IN
• Audio input jack (3.5mm) for an
external audio device.
e SRC
• Select a source: DISC, USB, DAB,
TUNER, BT, AUDIO IN.
f
g
• Start, pause, or resume play.
• Stop play or erase a program.
i
•
•
•
•
/
Skip to the previous/next track.
Search within a track/disc/USB.
Tune to a radio station.
Adjust time.
• Headphone socket.
j BASS
• Adjust bass level.
k TREBLE
• Adjust treble level.
l
• Open/close the disc compartment.
m VOLUME
• Adjust volume.
n NFC area
• Touch with a Near Field Communication
(NFC) compatible device to set up
Bluetooth connection automatically.
EN
5
e
Overview of the remote
control
a
r
b
c
INFO
RDS
SOURCE
PRESET/ALBUM
SCAN
d
q
p
e
MENU
f
VOL
DIM
SHUFFLE
g
MUTE
REPEAT
SOUND
CLOCK
PROG
TIMER
h
i
SLEEP
o
n
m
l
k
j
•
•
•
•
/
Skip to the previous/next track.
Search within a track/disc/USB.
Tune to a radio station.
Adjust time.
f VOL +/• Adjust volume.
g MUTE
• Mute or restore volume.
h SOUND
• Adjust BASS or TREBLE level.
i CLOCK
• Set the clock.
• View clock information.
j SLEEP/TIMER
• Set sleep timer.
• Set alarm timer.
k PROG
• Program tracks.
• Program radio stations.
l REPEAT/SHUFFLE
• Select repeat or shuffle play mode.
a
• Turn the unit on or off.
• Switch to standby mode or Eco power
standby mode.
b SOURCE
• Select a source: DISC, USB, DAB,
TUNER, BT, AUDIO IN.
c INFO/RDS
• Display current status or the disc
information.
• For selected FM radio stations, display
RDS information.
d PRESET/ALBUM /
• Select a preset radio station.
• Skip to previous/next album.
6
EN
m DIM
• Adjust display brightness.
n
o
• Start, pause, or resume play.
/MENU
• Stop play or erase a program.
• Access DAB+ or FM menu.
p OK
• Confirm a selection.
q SCAN
• Scan FM or DAB+ radio stations.
r
• Press to open or close the disc
compartment.
3 Get started
Connect FM antenna
Connect the supplied aerial to this device
before listening to the radio.
Caution
•• Use of controls or adjustments or performance of
procedures other than herein may result in hazardous
radiation exposure or other unsafe operation.
Always follow the instructions in this chapter in
sequence.
If you contact Philips, you will be asked for the
model and serial number of this apparatus. The
model number and serial number are on the
back of the apparatus. Write the numbers here:
Model No. __________________________
Serial No. ___________________________
SPEAKER OUT
Connect speakers
Note
•• For optimal sound, use the supplied speakers only.
•• Connect only speakers with impedance that is the
same or higher than the supplied speakers. Refer to the
Specifications section of this manual.
Connect power
Caution
•• Risk of product damage! Ensure that the power supply
voltage corresponds to the voltage printed on the back
or the underside of the unit.
•• Risk of electric shock! When you unplug the AC power
cord, always pull the plug from the socket. Never pull
the cord.
•• Before you connect the AC power cord, ensure that
you have completed all other connections.
SPEAKER OUT
1
2
3
SPEAKER OUT
EN
7
Prepare the remote control
Note
•• If no button is pressed in 90 seconds, the system exits
clock setting mode automatically.
Caution
•• Risk of explosion! Keep batteries away from heat,
sunshine or fire. Never discard batteries in fire.
Tip
•• Risk of decreased battery life! Never mix different
brands or types of batteries.
•• Risk of product damage! When the remote control is
not used for long periods, remove the batteries.
•• You can view clock information in power-on mode by
pressing CLOCK.
To insert the remote control battery:
1
2
3
Open the battery compartment.
Turn on
Insert the supplied AAA battery with
correct polarity (+/-) as indicated.
Press .
»» The unit switches to the last selected
source.
Close the battery compartment.
Switch to standby mode
Press again to switch the unit to standby
mode.
»» The clock (if set) is displayed on the panel.
Demonstrate the features
In standby mode, press and hold for three
seconds to demonstrate features of this device.
»» The features are displayed one by one
across the display panel.
•
To turn off the demonstration, press
again.
Switch to ECO standby mode:
Press and hold for more than two seconds.
»» The display panel is dimmed.
Note
•• The unit switches to Eco Power Standby mode after 15
minutes in standby mode..
Set clock
1
2
3
4
8
In standby mode, press and hold CLOCK
on the remote control for three seconds.
»» [24H] or [12H] hour format is
displayed.
Press
/
to select [24H] or [12H]
hour format.
press CLOCK to confirm.
»» The hour digits are displayed and begin
to blink.
Repeat steps 2-3 to set hour and minute.
EN
Switch between standby mode and ECO
standby mode:
Press and hold for more than two seconds.
4Play
SOURCE
SOURCE
INFO
RDS
PRESET/ALBUM
SCAN
MENU
VOL
Play from disc
1
DIM
SHUFFLE
MUTE
REPEAT
SOUND
CLOCK
PROG
TIMER
SLEEP
Press SOURCE repeatedly to select DISC
source.
2
3
Press
to open the disc compartment.
Insert a disc with printed side facing
upward.
4
Press to close the disc compartment.
»» Play starts automatically. If not, press
.
SOURCE
SOURCE
INFO
RDS
PRESET/ALBUM
SCAN
Charge your device
You can charge your device through the USB
socket on this product with a USB cable (not
supplied).
MENU
VOL
DIM
SHUFFLE
MUTE
REPEAT
SOUND
CLOCK
PROG
TIMER
SLEEP
Note
•• The maximum current for USB charging is 1 A.
•• All devices for USB charging are not guaranteed.
Play from USB
Note
•• Make sure that the USB device contains playable audio
content.
1
2
Press SOURCE repeatedly to select USB
source.
Insert a USB device into the
socket.
»» Play starts automatically. If not, press
.
EN
9
Control play
/
/
REPEAT/
SHUFFLE
VOL +/MUTE
SOUND
DIM
Select a folder.
Select an audio file.
Pause or resume play.
Stop play.
Select an available play mode.
• [REPEAT ONE] (repeat one):
repeat the current track
• [REPEAT ALB] (repeat album):
repeat the current album
• [REPEAT ALL] (repeat all):
repeat all tracks
• [SHUFFLE] (shuffle): play tracks
randomly
• [OFF] (off): play tracks in
sequence
Increase or decrease volume.
Mute or restore sound.
Press SOUND to select treble or
bass mode, and then press VOL +/to adjust treble or bass volume.
Press and hold SOUND for
three seconds to turn on or off
LOUDNESS.
Adjust display brightness.
Skip to a track
For CD:
Press
/
to select another track.
For MP3 disc and USB:
1
2
Press
Press
/
to select an album or a folder.
/
to select a track or a file.
Program tracks
You can program a maximum of 20 tracks.
1
Press PROG to activate the program mode.
10
EN
2
3
4
5
For MP3 tracks, press
album.
/
to select an
Press
/
to select a track, and then
press PROG to confirm.
Repeat steps 2-3 to program more tracks.
Press
to play the programmed tracks.
»» During play, [PROG] (program) is
displayed.
• To erase the program, in the stop
position, press .
Play from Bluetooth-enabled
devices
Note
•• Before pairing a device with this system, read its user
manual for Bluetooth compatibility.
•• Compatibility with all Bluetooth devices is not
guaranteed.
•• Any obstacle between the system and the device can
reduce the operational range.
•• The effective operation range between this product
and your Bluetooth enabled device is approximately 10
meters (30 feet).
•• The unit can memorize up to 8 previously connected
Bluetooth devices.
To enjoy music through the speaker wirelessly,
you need to pair your Bluetooth enabled device
with the unit.
Choose your best Bluetooth pairing method
based on the preconditions listed below.
Precondition
Your Bluetooth device
supports both Near
Field Communication
(NFC) and Advanced
Audio Distribution
Profile (A2DP).
Your Bluetooth device
only supports A2DP.
Pairing method
Choose Option 1
(recommended) or
Option 2.
Choose Option 2.
Option 2: Pair and connect manually
Pair and connect
Option 1: Pair and connect through NFC
Near Field Communication (NFC) is a technology
that enables short-range wireless communication
between various NFC compatible devices, such as
mobile phones and IC tags.
With the NFC function, data communication
can be achieved easily just by touching the
relevant symbol or designated location on NFC
compatible devices.
1
2
3
Note
•• Compatibility with all NFC devices is not guaranteed.
1
2
3
4
SOURCE
Press SOURCE repeatedly to select BT
source.
»» [BT] (Bluetooth) is displayed.
»» The Bluetooth indicator flashes blue.
On the Bluetooth enabled device, search
for Bluetooth devices that can be paired
(see the user manual of the device).
Select 'Philips BTB7150' on your
Bluetooth enabled device and input '0000'
as the paring password if necessary.
»» After successful pairing and connection,
the Bluetooth indicator turns solid
blue, and the unit beeps.
Press SOURCE repeatedly to select BT
source.
»» [BT] (Bluetooth) is displayed.
»» The Bluetooth indicator flashes blue.
Enable the NFC feature on your Bluetooth
enabled device (see the user manual of the
device for details).
Keep the NFC area of the external device
and the NFC area of this product within
2 cm.
Accept 'PHILIPS BTB7150' pairing for
the first-time use, and input '0000' as the
paring password if necessary.
»» After successful pairing and connection,
the Bluetooth indicator turns solid
blue, and the unit beeps.
RDS
<2 cm
SOURCE
INFO
PRESET/ALBUM
SCAN
SOURCE
INFO
RDS
0000
ON
SCAN
BTB7150
PIN
0000
Stream music through Bluetooth
•
PIN
SOURCE
PRESET/ALBUM
Play audio on the Bluetooth device
connected to this product.
»» Audio streams from your Bluetooth
enabled device to the speakers of this
product.
To disconnect the Bluetooth-enabled device:
• Deactivate Bluetooth on your device; or
• Move the device beyond the
communication range.
EN
11
To clear Bluetooth pairing history:
• Pressand hold
on the main set for
eight seconds.
»» After successful clearing, beep sounds.
Play from Philips DigitalRadio application
An application Philips DigitalRadio is available
on Apple App Store and Google Play.
To fully enjoy features of this product, download
and install the application to your smart device.
With this application, after connect your
Bluetooth-enabled device to this product, you
can control DAB, TUNER, BT, and AUDIO IN
play mode from your Bluetooth-enabled device.
5 Listen to the
radio
Tip
•• Position the antenna as far as possible from TV, VCR, or
other radiation source.
•• Make sure that you have connected the supplied aerial.
•• For optimal reception, fully extended and adjust the
position of the aerial.
Listen to DAB+ radio
Digital Audio Broadcasting (DAB+) is a way
of broadcasting radio digitally through a
network of transmitters. It provides you with
more choice, better sound quality, and more
information.
Tune to DAB+ radio stations
Note
•• Make sure that the antenna is fully extended.
Press SOURCE repeatedly to select DAB
source.
»» [FULL SCAN] (full scan) is displayed.
»» The unit stores all DAB+ radio stations
automatically and broadcasts the first
available station.
»» The station list is memorized in the unit.
Next time when you turn on the unit, the
station scan does not take place.
Note
•• If no DAB+ radio station is found, [NO DAB] (no
DAB) is displayed, then [FULL SCAN] (full scan) is
displayed again.
12
EN
To tune to a station from the available station
list:
In DAB+ mode, press
/
repeatedly to
navigate through the available DAB+ stations.
Select a preset DAB+ radio station
Store DAB+ radio stations
automatically
Show DAB+ information
Note
•• New stations and services will be added in DAB+
broadcast from time to time. To make new DAB+
stations and services available, perform full scan
regularly.
In DAB+ mode, press SCAN.
»» The unit scans and stores all the available
DAB+ radio stations, and broadcasts the
first available station.
Store DAB+ radio stations manually
•• You can store a maximum of 20 preset DAB+ radio
stations.
3
4
5
While listening to DAB+ radio, press INFO/
RDS repeatedly to scroll through the following
information (if available):
• Station Name
• RDS TEXT message
• Dynamic Label Segment
• Program Type
• Ensemble Name
• Frequency
• Signal error rate
• Bit rate
• Audio status (DAB, DAB+)
• Time
• Date
Use DAB+ menu
Note
1
2
In DAB+ mode, press / to select a preset
number, and then press OK to confirm..
In DAB+ mode, press MENU to access DAB+
menu.
1
Tune to a DAB+ radio station.
Press PROG for three seconds to activate
the storing mode.
Press
/
to select a channel.
Press PROG to confirm.
»» The name of the preset station is
displayed.
Repeat above steps to store more DAB+
stations.
Note
•• To remove a pre-stored DAB+ radio station, store
another station in its place.
2
3
Press
/
to scroll the menu options:
• [Full scan] (full scan): scan and store all
the available DAB+ radio stations.
• [Manual] (manual): tune to a DAB+
station manually.
• [Prune] (prune): remove all the invalid
stations from the station list.
• [System] (system): adjust system
settings.
To select an option, press OK.
If a sub-option is available, repeat steps
2- 3.
[System] (system)
•• [Reset] (reset): reset all settings to factory
default.
•• [BT RESET] (Bluetooth reset): reset
Bluetooth settings to factory default.
•• [UPGRADE] (upgrade): upgrade software
if available.
EN
13
••
••
[BT UPGRADE] (Bluetooth upgrade):
upgrade Bluetooth software if available.
[SW VER] (software version): show the
software version of this unit.
4
In FM tuner mode, press SCAN.
»» The stations scanned are based on the
selection in step 2.
»» The unit broadcasts the first scanned
FM radio stations.
Note
•• If no button is pressed within 30 seconds, the menu
exits.
Listen to FM radio
Tune to a radio station
1
2
3
Press SOURCE repeatedly to select tuner
source.
Press and hold
/
for three seconds.
»» The radio tunes to a station with
strong reception automatically.
Store FM radio stations automatically
Note
•• You can program a maximum of 20 preset radio
stations (FM).
2
3
14
1
2
3
4
5
In tuner mode, press MENU to access FM
tuner menu.
»» [SCAN] is displayed.
Press OK, and then press
/
to scroll
the menu options:
• [Strong] (strong stations): scan stations
with strong signals only.
• [All] (all stations): scan all available FM
radio stations.
Press OK to select an option.
EN
Tune to an FM radio station.
Press PROG to activate programming
mode.
»» [PROG] (program) blinks.
Press
/
repeatedly to select a number.
Press PROG again to confirm.
»» The frequency of the preset station is
displayed.
Repeat above steps to store more FM
stations.
Note
Repeat step 2 to tune to more stations.
To tune to a weak station:
Press
/
repeatedly until you find optimal
reception.
1
Store FM radio stations manually
•• To remove a pre-stored station, store another station
in its place.
Select a preset radio station
In FM mode, press / to select a preset
number, and then press OK to confirm.
Show RDS information
Radio Data System (RDS) is a service
that allows FM stations to show additional
information.
1
2
Tune to an RDS station.
Press RDS/INFO repeatedly to scroll
through the following information (if
available).
• Radio text message
• Program type
• Frequency
• Stereo or Mono
6 Other features
Set the alarm timer
This unit can be used as an alarm clock. You can
select DISC, TUNER, DAB, or USB as alarm
source.
Note
•• Make sure that you have set the clock correctly.
1
2
3
4
In standby mode, press and hold SLEEP/
TIMER for three seconds.
»» [SET TIMER] is displayed, and then
[DISC] is displayed and begins to blink.
Press
/
(or SOURCE) repeatedly
to select an alarm source (DISC, TUNER,
DAB, or USB).
Press SLEEP/TIMER (or OK) to confirm.
»» The hour digits are displayed and begin
to blink.
Repeat steps 2-3 to set hour, minute, and
adjust volume of the alarm.
Set the sleep timer
To set the sleep timer, in turn on mode, press
SLEEP/TIMER repeatedly to select a set period
of time (in minutes).
»» When sleep timer is activated, is
displayed. Otherwise, disappears.
Listen to an external device
You can listen to an external device through this
unit with an audio cable.
1
Press SOURCE repeatedly to select
AUDIO IN source.
2
Connect an audio cable (not supplied)
between:
• AUDIO IN jack (3.5 mm) on the unit;
• and the headphone jack on an external
device.
3
INFO
RDS
Start to play the device (see the device
user manual).
SOURCE
SOURCE
PRESET/ALBUM
SCAN
MENU
VOL
DIM
SHUFFLE
MUTE
REPEAT
SOUND
CLOCK
PROG
TIMER
SLEEP
Note
•• If no button is pressed in 90 seconds, the system exits
timer setting mode automatically.
To activate or deactivate the alarm timer:
Press SLEEP/TIMER repeatedly to view the
alarm information and activate or deactivate the
alarm.
»» If timer is activated, is displayed.
»» If timer is deactivated, [TIMER OFF] (timer
off) is displayed and disappears.
Tip
•• If DISC/USB source is selected, but no disc is placed
or no USB connected, the system switches to tuner
source automatically.
AUDIO IN
Listen through a headphone
Plug a headphone (not supplied) into the
socket on front of this product.
EN
15
7Product
information
Note
USB
USB Direct Version
USB Charging
Bluetooth
•• Product information is subject to change without prior
notice.
Bluetooth version
Frequency band
Range
Specifications
Amplifier
Maximum Output
Power
Frequency Response
Signal to Noise Ratio
Total Harmonic
Distortion
Aux Input
Sensitivity
60 Hz - 16 kHz;
±3 dB
≥70 dBA
<1%
600 mV RMS
4 ohm
5.25" woofer +
25 mm tweeter
>84 dB/m/W
Disc
Laser Type
Disc Diameter
Support Disc
Audio DAC
Total Harmonic
Distortion
Frequency Response
S/N Ratio
16
EN
V2.1 + EDR/support
APT-X
2.4 GHz ~ 2.48 GHz
ISM Band
10 m (free space)
Tuner (FM)
150 W
Speakers
Speaker Impedance
Speaker Driver
2.0 full speed
1A
Semiconductor
12 cm/8 cm
CD-DA, CD-R, CDRW, MP3-CD
24 Bits/44.1 kHz
<1% (1 kHz)
60 Hz - 16 kHz;
±3 dB
>70 dBA
Tuning Range
Tuning grid
Sensitivity
- Mono, 26 dB S/N Ratio
- Stereo, 46 dB S/N Ratio
Search Selectivity
Total Harmonic
Distortion
Signal to Noise Ratio
87.5-108 MHz
50 KHz
<22 dBf
<45 dBf
<30 dBf
<3%
>45 dBA
General information
AC power
Operation Power
Consumption
Eco Standby Power
Consumption
Dimensions
-M
ain Unit
(W x H x D)
- S peaker Box
(W x H x D)
Weight
- Main Unit
- Speaker Box
100-240 V~, 50/60 Hz
45 W
<0.5 W
230 x 145 x 240 mm
173 x 261 x 241 mm
2.9 kg
2 x 3.1 kg
USB playability information
RDS program types
Compatible USB devices:
•• USB flash memory (USB2.0 or USB1.1)
•• USB flash players (USB2.0 or USB1.1)
•• memory cards (requires an additional card
reader to work with this unit)
NO TYPE
NEWS
AFFAIRS
INFO
SPORT
EDUCATE
Supported USB formats:
•• USB or memory file format: FAT12, FAT16,
FAT32 (sector size: 512 bytes)
•• MP3 bit rate (data rate): 32-320 Kbps and
variable bit rate
•• Directory nesting up to a maximum of 8
levels
•• Number of albums/ folders: maximum 99
•• Number of tracks/titles: maximum 999
•• ID3 tag v2.0 or later
•• File name in Unicode UTF8 (maximum
length: 32 bytes)
Unsupported USB formats:
•• Empty albums: an empty album is an album
that does not contain MP3/WMA files, and
will not be shown in the display.
•• Unsupported file formats are skipped. For
example, word documents (.doc) or MP3
files with extension .dlf are ignored and
not played.
•• WMA, AAC, WAV, PCM audio files
•• DRM protected WMA files (.wav, .m4a,
.m4p, .mp4, .aac)
•• WMA files in Lossless format
•• FLAC files
Supported MP3 disc formats
•
•
•
•
•
ISO9660, Joliet
Maximum title number: 128 (depending on
file name length)
Maximum album number: 99
Supported sampling frequencies: 32 kHz,
44.1 kHz, 48 kHz
Supported Bit-rates: 32~256 (kbps),
variable bit rates
DRAMA
CULTURE
SCIENCE
VARIED
POP M
ROCK M
MOR M
LIGHT M
CLASSICS
OTHER M
WEATHER
FINANCE
CHILDREN
SOCIAL
RELIGION
PHONE IN
TRAVEL
LEISURE
JAZZ
COUNTRY
NATION M
OLDIES
FOLK M
DOCUMENT
TES
ALARM
No RDS programme type
News services
Politics and current affairs
Special information programs
Sports
Education and advanced
training
Radio plays and literature
Culture, religion and society
Science
Entertainment programs
Pop music
Rock music
Light music
Light classical music
Classical music
Special music programs
Weather
Finance
Children’s programs
Social Affairs
Religion
Phone In
Travel
Leisure
Jazz Music
Country Music
National Music
Oldies Music
Folk Music
Documentary
Alarm Test
Alarm
EN
17
8Troubleshooting
Warning
•• Never remove the casing of this device.
To keep the warranty valid, never try to repair
the system yourself.
If you encounter problems when using this device,
check the following points before requesting
service. If the problem remains unsolved, go to
the Philips Web page (www.philips.com/support).
When you contact Philips, make sure that the
device is nearby and the model number and serial
number are available.
No power
•• Make sure that the AC power cord of the
device is connected properly.
•• Make sure that there is power at the AC
outlet.
•• As a power-saving feature, the system
switches off automatically 15 minutes after
track play reaches the end and no control
is operated.
No sound or poor sound
•• Adjust the volume.
•• Check that the speakers are connected
correctly.
•• Check if the stripped speaker wires are
clamped.
No response from the unit
•• Disconnect and reconnect the AC power
plug, then turn on the unit again.
Remote control does not work
•• Before you press any function button, first
select the correct source with the remote
control instead of the main unit.
•• Reduce the distance between the remote
control and the unit.
•• Insert the battery with its polarities (+/signs) aligned as indicated.
•• Replace the battery.
•• Aim the remote control directly at the
sensor on the front of the unit.
18
EN
No disc detected
•• Insert a disc.
•• Make sure that the disc is inserted with
printed side facing upward.
•• Wait until the moisture condensation at
the lens has cleared.
•• Replace or clean the disc.
•• Use a finalized CD or correct format disc.
Cannot display some files in USB device
•• The number of folders or files in the USB
device has exceeded a certain limit. This
phenomenon is not a malfunction.
•• The formats of these files are not
supported.
USB device not supported
•• The USB device is incompatible with the
unit. Try another one.
Poor radio reception
•• Increase the distance between the unit and
your TV or VCR.
•• Connect and fully extend supplied antenna.
Music playback is unavailable on this unit even
after successful Bluetooth connection.
•• The device cannot be used to play music
through this unit wirelessly.
The audio quality is poor after connection
with a Bluetooth-enabled device.
•• The Bluetooth reception is poor. Move the
device closer to this unit or remove any
obstacle between them.
Bluetooth cannot be connected with this unit.
•• The device does not support the profiles
required for this unit.
•• The Bluetooth function of the device is
not enabled. Refer to the user manual of
the device to find out how to enable the
function.
•• This unit is not in pairing mode.
•• This unit is already connected with another
Bluetooth-enabled device. Disconnect that
device and then try again.
• If you pair and connect through NFC,
make sure that:
• you have enabled both the Bluetooth
and NFC features on your device.
• you have kept the NFC area of the
device in touch with that of the
speaker until you heard a beep.
The paired mobile device connects and
disconnects constantly.
•• The Bluetooth reception is poor. Move the
device closer to this unit or remove any
obstacle between them.
•• Some mobile phones may connect and
disconnect constantly when you make
or end calls. This does not indicate any
malfunction of this unit.
•• For some devices, the Bluetooth
connection may be deactivated
automatically as a power-saving feature.
This does not indicate any malfunction of
this unit.
Timer does not work
•• Set the clock correctly.
•• Switch on the timer.
Clock/timer setting erased
•• Power has been interrupted or the power
cord has been disconnected. Reset the
clock/timer.
9Notice
Any changes or modifications made to this
device that are not expressly approved by
Gibson Innovations may void the user’s
authority to operate the equipment.
Hereby, Gibson Innovations declares that
this product is in compliance with the
essential requirements and other relevant
provisions of Directive 1999/5/EC. You
can find the Declaration of Conformity on
www.philips.com/support.
Your product is designed and manufactured
with high quality materials and components,
which can be recycled and reused.
When this crossed-out wheeled bin symbol is
attached to a product it means that the product
is covered by the European Directive 2002/96/
EC.
Please inform yourself about the local separate
collection system for electrical and electronic
products.
Please act according to your local rules and
do not dispose of your old products with your
normal household waste. Correct disposal of
your old product helps to prevent potential
negative consequences for the environment and
human health.
EN
19
This apparatus includes this label:
Your product contains batteries covered by
the European Directive 2006/66/EC, which
cannot be disposed with normal household
waste.Please inform yourself about the local
rules on separate collection of batteries
because correct disposal helps to prevent
negative consequences for the environmental
and human health.
Environmental information
All unnecessary packaging has been omitted.
We have tried to make the packaging easy to
separate into three materials: cardboard (box),
polystyrene foam (buffer) and polyethylene
(bags, protective foam sheet.)
Your system consists of materials which can
be recycled and reused if disassembled by
a specialized company. Please observe the
local regulations regarding the disposal of
packaging materials, exhausted batteries and old
equipment.
This item incorporates copy protection
technology that is protected by U.S. patents
and other intellectual property rights of
Rovi Corporation. Reverse engineering and
disassembly are prohibited.
The Bluetooth® word mark and logos are
registered trademarks owned by Bluetooth
SIG, Inc. and any use of such marks by Gibson
Innovations is under license.
The N Mark is a trademark or registered
trademark of NFC Forum, Inc. in the United
States and in other countries.
20
EN
Note
•• The type plate is located on the back of the device.
21
2016 © Gibson Innovations Limited. All rights reserved.
This product has been manufactured by, and is sold under the responsibility of Gibson Innovations Ltd., and
Gibson Innovations Ltd. is the warrantor in relation to this product.
Philips and the Philips Shield Emblem are registered trademarks of Koninklijke Philips N.V. and are used under
license from Koninklijke Philips N.V.
BTB7150_10_UM_V4.0
Download PDF
Similar pages
Sangean DPR-202 DAB Radio
Roberts Radio Revival Mini
Soundmaster DAB500SI
Soundmaster IR3000DAB
Soundmaster DAB 200
Lenco DR-05 BT
Stream 104
fm-100dab 2
Lenco DR-88 BT