USER’S
MANUAL
MP-1060
Thermal Receipt Printer
MP-1060
M1
Copyright Notice
MP-1060
Thermal Printer
COPYRIGHT NOTICE & TRADEMARK
All trademarks and registered trademarks mentioned herein are the property of their
respective owners.
This manual is copyrighted in June 2015. You may not reproduce or transmit in
any form or by any means, electronic, or mechanical, including photocopying and
recording.
DISCLAIMER
This operation manual is meant to assist you in using the printer board. The
information contained in this document is subject to change without any notice.
Contents
TABLE OF CONTENTS
CHAPTER 1 INTRODUCTION
1-1
1-2
1-3
1-4
About This Manual…................................................................
System Specification………………………………………….
General Specification….............................................................
Safety Precautions…..................................................................
1-2
1-3
1-4
1-6
CHAPTER 2 HARDWARE CONFIGURATION
2-1
2-2
2-3
2-4
2-5
2-6
2-7
Unpacking…………………………………...…........................
Part Structure………..….….......................................................
Connectors.................................................................................
Installing and Replacing Roll Paper……...................................
Attaching and Removing the Connector Cover..........................
Attaching and Removing the Splash Proof Cover…..................
Attaching and Removing the Paper Guide.…………………....
CHAPTER 3
3-1
3-2
3-3
3-4
4-1
4-2
3-2
3-3
3-4
3-8
HEXADECIMAL DUMPING & SELF-TESTING
Hexadecimal dumping...............................................................
Self-Testing………………………………................................
CHAPTER 5
5-1
5-2
INSTALL AND SETUP
Install the printer……..........................................…..................
Setting the DIP Switch………………….…..……..…............
DIP Switches functions…...……………………………………
Adjusting the Paper-near-end sensor..…………..………..........
CHAPTER 4
2-2
2-5
2-8
2-9
2-11
2-13
2-13
4-2
4-2
SOFTWARE CONFIGURATION
Ethernet Interface Card Setting..................................................
Printer Driver Setting……………………….............................
5-2
5-4
Contents
CHAPTER 6
6-1
6-2
6-3
6-4
CHAPTER 7
7-1
7-2
7-3
7-4
7-5
7-6
COMMAND LIST
Standard Command List.............................................................
Two-Dimensional Bar Code Command Details.........................
Kanji Control Command Details……........................................
Standard Command Details…………………............................
6-2
6-4
6-5
6-6
LANGUAGES
Ank Codes……………..............................................................
International Characters………………………..........................
Japanese Language Codes (Shift-JIS Codes)…….....................
Taiwanese Language Codes…………………...........................
Simplified Chinese Language Codes……………......................
Korean Language Codes……………………………………….
7-2
7-5
7-6
7-14
7-29
7-41
CHAPTER
INTRODUCTION
1
This chapter gives you the information for MP-1060. It also outlines
the system specifications.
Sections include:

About This Manual

System Specifications

Safety Precautions
Experienced users can jump to chapter 2 on page 2-1 for a quick
start.
Page:1-1
Chapter
1
Introduction
1-1. ABOUT THIS MANUAL
Thank you for purchasing our MP-1060 Thermal Receipt Printer System. The
MP-1060 is an updated system designed to be comparable with the highest
performance of Point-of-Sale platforms. The MP-1060 provides faster
processing speed, greater flexibility and can handle more commands than ever.
This manual is designed to assist you how to install and set up the whole system.
It contains five chapters. The user can refer the user’s manual for configuration
according to the following chapters:
Chapter 1 Introduction
This chapter introduces you to the background of this manual, and the
specifications for this printer board. The final page of this chapter will indicate
how to avoid damaging this board.
Chapter 2 Parts and Basic Operation
Chapter 3 Install and Set Up
Chapter 4 Hexadecimal Dumping & Self-Test
Chapter 5 Software Configuration
This chapter indicates you how to set up the printer system through the software
utility.
Page: 1-2
MP-1060 USERS MANUAL
Chapter
1
Introduction
Catchphrase:
1-2. SYSTEM SPECIFICATION
Features:

200mm high speed printing

Vertical and horizontal stand position capable

Built-in multi-language codepage includes Chinese, Japanese and
Korean characters

Support digital LOGO printing saved in FLASH ROM

Modularized design of printer head.

Multiple interface for USB/Serial and Ethernet Port

Auto paper cutter for full cut and partial cut available

Paper-near-end detector sensor and LED/Buzzer warring indicator.

EPSON command and other emulation

1D/2D barcode printing supported

Easy to set and high volume capacity of paper

Spectacular value-add accessories

OPOS driver supported
MP-1060 USERS MANUAL
Page: 1-3
Chapter
1
Introduction
1-3. GENERAL SPECIFICATIONS
General
Print method
Printing width
Paper width
Printable dot No.
Printing speed
Resolution
Sensors
Cutter
Paper
Reliability
Type
Thickness
Roll diameter
Printing head
MCBF
Auto cutter
Interface
Performance
Software
Physical
Page: 1-4
Receive Buffer
Logo size
Emulation Driver
Dimensions
Weight
Cash drawer
Power supply
Thermal Line Printing
72mm
80mm
576 dots
Up to 200 mm/sec
8 dot/mm
Paper end, Cover Open,
Paper-near-end(Optional)
Auto Cutter (Full/Partial)
Tear bar
Receipt Thermal paper
0.06mm~0.09mm
Max. 80.0mm
100 km
60 million lines
1.5 million cuts
USB(Virtual COM)/Serial,
Ethernet(Optional)
4KB
64K
ESC/POS CMD compatible
WinXP/Win7/Win8/
-32bits & 64bits/OPOS
142mm x 127mm x 154mm
980g (w/o paper roll)
1x 6pin RJ-11 connecter
External 24v Adaptor
MP-1060 USERS MANUAL
Chapter
Language
Barcode
Introduction
Alphanumeric Characters: 95
Extended Characters: 128 x 8
Character Sets
Page (Blank x 1 Page)
International Characters: 32
CP-437, Katakana character set,
Code Page
CP-850, CP-852, CP-860, CP-863,
CP-865, WPC-1252
Compound
Traditional Chinese, Simple
Character
Chinese, Japanese, Korean
Font A: 12 x 24 (default)
Character Size
Font B: 9 x 17
Font C: 24 x 24
Font A: 36 C/L
No. char per line Font B: 48 C/L
Font C: 18 C/L
UPC-A, UPC-E, JAN8(EAN8),
JAN13(EAN13), CODE39,
1D
ITF(Interleaved 2 of 5),
CODABAR(NW-7), CODE93,
CODE128,
2D
Operating Temp
Environment
1
Storage Temp
Operating Temp
Storage Temp
Accessories
Certification
MP-1060 USERS MANUAL
QR Code
-10 to 50°C (35 °C In case of
Printing-rate over 10%)
-30 to 60°C
10 to 90% RH
10 to 90% RH expect for paper
2” Paper Guide, Splash Proof
Cover, Wall-mount Kit, Cable
Cover, Paper-near-end Sensor Kit,
Melody Box, Interface Cables,
International Power Cords
CE, FCC
Page: 1-5
Chapter
1
Introduction
1-4. SAFETY PRECAUTIONS
Following messages are safety reminders on how to protect your systems from
damages. And thus, helps you lengthen the life cycle of the system.
1. Check the Line Voltage
a. The operating voltage for the power supply should cover the range of
100VAC-240V AC, otherwise the system may be damaged.
2. Environmental Conditions
a. Avoid extremely hot or cold places to install MP-1060.
b. Avoid exposure to sunlight for a long period of time (for example in a closed
car in summer time. Also avoid the system from any heating device.). Or do not
use MP-1060 when it‘s been left outdoors in a cold winter day.
c. Bear in mind that the operating ambient temperature is from 5C up to +35C.
d. Avoid moving the system rapidly from a hot place to a cold place or vice
versa because condensation may come from inside of the system.
e. Place MP-1060 against strong vibrations, which may cause hard disk failure.
f. Do not place the system too close to any radioactive device. Radio-active
device may cause interference.
3. Good Care
a. When the outside of the case is stained, remove the stain with neutral
washing agent with a dry cloth.
b. Never use strong agents such as benzene and thinner to clean the system.
c. If heavy stains are present, moisten a cloth with diluted neutral washing agent
or with alcohol and then wipe thoroughly with a dry cloth.
d. If dust has been accumulated on the outside, remove it by using a special
made vacuum cleaner for computers.
Page: 1-6
MP-1060 USERS MANUAL
CHAPTER
PARTS AND BASIC
OPERATION
2
Helpful information describes the parts and operation of MP-1060.
Sections include:
Unpacking
Part Structure
Connectors
Page 2-1
Chapter
2
Parts and Operations
2-1. UNPACKING
2-1-1 Main parts
Printer (body) × 1
User’s CD-ROM × 1
Page: 2-2
External power supply unit × 1
MP-1060 USER′S MANUAL
Chapter
2
Hardware Configuration
2-1-2 Options
Cable cover
plash proof cover
Splash
2” Paper guide
2”/3
/3” 10M Test Roll paper
Wall mount kits Hanging bracket set
MP-1060 USER′S MANUAL
Page: 2-3
Chapter
2
Parts and Operations
External Interface Cables (USB/Serial/LAN)
Page: 2-4
MP-1060 USER′S MANUAL
Chapter
2
Hardware Configuration
2-2 Part Structure
2-2-1 Main body
MP-1060 USER′S MANUAL
Page: 2-5
Chapter
2
Parts and Operations
2-2-2 Control Panel
POWER (Blue)
Lights when the power supply is on.
Goes out when the power supply is turned off.
ERROR (Red)
Lights when an error occurs.
Goes out during regular operation.
PAPER (Yellow)
Lights when there is no more roll paper.
Goes out when there is a sufficient amount of roll paper remaining.
Flashes when paper near end sensor is enabled and there is little remaining.
Page: 2-6
MP-1060 USER′S MANUAL
Chapter
2
Hardware Configuration
2-2-3 Buttons
FEED button
Pressing this button once feeds the roll paper by one line. Holding this button
down and feeds the roll paper continuously.
2-2-4 Power Switch
The power switch is located at the bottom right front of the printer.
Turn the printer on or off. The marks on the switch (0 = on / 1 = off) indicate
the printer switch position.
CAUTION:
Before turning on the printer be sure to check that the AC adapter is connected
to the power supply.
MP-1060 USER′S MANUAL
Page: 2-7
Chapter
2
Parts and Operations
2-3 Connectors
All cables are connected to the connector panel on the lower rear of the printer.
Drawer kick-out connector for connecting the cash drawer
Power supply connector for connecting the power supply unit
Interface connector to connect the printer to the host computer interface
(serial/USB/LAN)
Page: 2-8
MP-1060 USER′S MANUAL
Chapter
2
Hardware Configuration
2-4 Installing and Replacing Roll Paper
CAUTION:
Be sure to use roll paper that meets printer specifications. Do not use roll
paper whose trailing end is glued to the roll paper core.
Installing Roll Paper
1.
Make sure the host has not sent a printing command to the printer, and
press the cover open button to open the printer cover.
MP-1060 USER′S MANUAL
Page: 2-9
Chapter
2.
2
Parts and Operations
Load the roll paper.
Horizontal position:
Vertical position:
CAUTION:
When loading the roll paper, pay attention to the direction that the roll paper is
fed out of the printer.
3.
Pull out the roll paper toward you, and then close the printer cover.
Page: 2-10
MP-1060 USER′S MANUAL
Chapter
2
Hardware Configuration
2-5 Attaching and Removing the Connector Cover
These instructions apply if a cable is packed with your printer to protect your
cables.
To attach it, follow the steps below:
1.
First, connect all the cables and use cable clip and screw to fix the
cables, as shown in illustration
MP-1060 USER′S MANUAL
Page: 2-11
Chapter
2
Parts and Operations
2.
Position the two hooks on the connector cover so that they hook the
printer case, as shown in illustration.
3.
Push the connector cover down to click onto the printer case.
Page: 2-12
MP-1060 USER′S MANUAL
Chapter
2
Hardware Configuration
2-6 Attaching and Removing the Splash Proof Cover
1.
Position the two hooks on the right and left side at the bottom, so that
they could hook the printer case, as shown in illustration.
2-7 Attaching and Removing the Paper Guide
1.
Open the front door and insert the paper guide as shown in illustration.
MP-1060 USER′S MANUAL
Page: 2-13
Chapter
2
Parts and Operations
2.
Position the top hook point of the paper guide into the corresponding
hole of the printer, as shown in illustration.
3.
Position the left hook point of the paper guide into the corresponding
hole of the printer, as shown in illustration.
Page: 2-14
MP-1060 USER′S MANUAL
INSTALL AND
SETUP
CHAPTER
3
This chapter comprises the information of install and setup for
MP-1060.
Sections include:
Install the printer
Setting the DIP Switch
DIP Switches functions
Adjusting the Paper-near-end sensor.
Page: 3-1
Chapter
3-1
3
Control Command
Install the Printer
In addition to regular horizontal and vertical installation, the printer can be
hung on a wall using the optional Wall hanging bracket Set.
3-1-1 Precautions for regular vertical and horizontal Installation
Install the printer in a flat, horizontal or vertical position.
Avoid locations susceptible to dust and other foreign matter.
Be sure to avoid bumping so that the printer is not exposed to strong
impact during operation.
Avoid placing the printer on top of the power supply or other cables or
other objects.
3-1-2 Precautions for Wall Installation
Make the following settings on the printer when you hang it on a wall.
1.Set the printer at vertical position
2.Adjust of near-end detector
3.Attach the connector cover
4.Install the Hanging Bracket Set
Page:3-2
MP-1060 USER′S MANUAL
Chapter
3-2
3
Control Commands
Setting the DIP Switches
DIP Switch Positions and Steps for Changing DIP Switch Settings
Follow the steps below to change the DIP switch settings
CAUTION:
Always change DIP switch settings only when the printer is turned off.
Change made with the power on have no effect and then on again.
1.
2.
Make sure the power supply for the printer is turned off.
Unscrew the screw to remove the DIP switch cover from the base of
the printer.
3.
Set the DIP switches as desired, using the tip of a tool, such as a small
screwdriver.
Attach the DIP switch cover, and screw in place.
4.
MP-1060 USER′S MANUAL
Page:3-3
Chapter
3-3
3
Control Command
DIP Switches functions
3-3-1 RS-232C Serial Interface
SW
Function
1
Auto Line Feed
2
3
4
5
6
7
8
Initial setting
Handshaking
Word length
Parity check
Parity selection
SW
1
2
3
4
5
6
7
8
Page:3-4
Baud rate selection
Function
Code Page
Selection
Internal bell
control
Ethernet Interface
Near End Sensor
Status
Select Print
Density
DIP Switch 1
ON
OFF
Always
Always
disabled
enabled
Initial by SW
Initial by HW
XON/OFF
DTR/DSR
7 bits
8 bits
Yes
No
EVEN
ODD
Refer to Table 1 - Baud Rate
Selection
DIP Switch 2
ON
OFF
Table 3 - Code Page Selection
Default
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
Default
OFF
OFF
OFF
Enable
Disable
ON
Enable
Disable
OFF
Enable
Disable
OFF
Refer to Table 2 –
Density Selection
OFF
OFF
MP-1060 USER′S MANUAL
Chapter
3
Control Commands
3-3-2 USB/IEEE1284 Interface
SW
1
2
3
4
5
6
7
8
Function
Auto Line Feed
Reserved
Reserved
Reserved
Reserved
Reserved
Reserved
Reserved
SW
1
2
3
4
5
6
7
8
Function
DIP Switch 1
ON
Always disabled
DIP Switch 2
ON
OFF
Always enabled
-
OFF
Code Page Selection
Table 3 - Code Page Selection
Internal bell control
Ethernet Interface
Near End Sensor Status
Enable
Disable
Enable
Disable
Enable
Disable
Refer to Table 2 –
Density Selection
Select Print Density
MP-1060 USER′S MANUAL
Default
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
Default
OFF
OFF
OFF
ON
OFF
OFF
OFF
OFF
Page:3-5
Chapter
3
Control Command
3-3-3 Ethernet Interface
SW
1
2
3
4
5
6
7
8
Function
Auto Line Feed
Reserved
Reserved
Reserved
Reserved
Reserved
Reserved
Reserved
DIP Switch 1
ON
Always disabled
-
OFF
Always enabled
-
Default
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
SW
1
2
3
4
5
Function
DIP Switch 2
ON
OFF
6
7
8
Page:3-6
Code Page Selection
Internal bell control
Ethernet Interface
Near End Sensor
Status
Select Print Density
Enable
Enable
Disable
Disable
Default
OFF
OFF
OFF
ON
ON
Enable
Disable
OFF
Table 3 - Code Page Selection
Refer to Table 2 –
Density Selection
OFF
OFF
MP-1060 USER′S MANUAL
Chapter
Control Commands
Table 1 - Baud Rate Selection
SW-8
OFF
ON
OFF
ON
Baud rate
115200
57600
19200
9600
SW-7
OFF
OFF
ON
ON
Print Density
1 (Light)
2
3
4(Dark)
Table 2 - Density Selection
SW2-7
SW2-8
OFF
ON
ON
OFF
OFF
OFF
ON
ON
Code Page
CP-437
Katakana character
CP-850
CP-852
CP-860
CP-863
CP-865
WPC-1252
SW1-1
OFF
OFF
OFF
OFF
ON
ON
ON
ON
MP-1060 USER′S MANUAL
3
Table 3 - Code Page Selection
SW1-2
OFF
OFF
ON
ON
OFF
OFF
ON
ON
Note
60%
80%
100%
120%
SW1-3
OFF
ON
OFF
ON
OFF
ON
OFF
ON
Page:3-7
Chapter
3-4
3
Control Command
Adjusting the Paper-near-end sensor
Since roll paper cores vary slightly in shape, depending on paper roll design
and manufacturing tolerances, it impossible to detect the remaining paper
exactly.
Use roll paper with a core inner diameter of 12 mm and outer diameter of
18 mm, so the paper detector can detect the remaining paper as accurately as
possible.
Follow the procedure below to adjust the roll paper detector position.
1.
Open the roll paper cover, and remove the roll paper.
2.
Bend the adjustment lever to reposition paper sensor. Adjustment
positions are as follows:
3.
4.
After adjustment, load the roll paper.
Close the roll paper cover.
Page:3-8
MP-1060 USER′S MANUAL
Chapter
3
Control Commands
Adjustment position/Remaining amount of roll paper (outer diameter: mm)
Lv
4
3
2
1
3” Vertical
7.65mm~7.68mm
7.05mm~7.08mm
6.92mm~6.97mm
6.36mm~6.45mm
3” Horizontal
7.39mm~7.41mm
6.86mm~6.90mm
6.13mm~6.15mm
6.02mm~6.06mm
MP-1060 USER′S MANUAL
2” Vertical
7.77mm~7.80mm
7.49mm~7.57mm
6.99mm~7.00mm
6.39mm~6.46mm
2” Horizontal
7.35mm~7.47mm
6.93mm~7.08mm
6.12mm~6.18mm
5.75mm~5.99mm
Page:3-9
HEXADECIMAL
DUMPING &
SELF-TESTING
CHAPTER
4
This chapter shows hexadecimal dumping and self-testing of MP-1060.
Sections include:
Hexadecimal dumping
Self-Testing
Page: 4-1
Chapter
4
Hexadecimal Dumping & Self-Testing
4-1. HEXADECIMAL DUMPING
Explanation: Allow users to conduct Software problem finding through observing Data in Hex format feed to the printer.
Turn on:
1. Open “Printer Cover” when the computer is off
2. Click on the “Feed” to open “ Power switch”
3. Close the “Cover” to enter Hex dump mode
4. Execute any program to send data to printer. The printer will then print out
the data in two rows and hexadecimal format.
Turn off:
1. After the printing is complete, turn off the printer. The printer will resume normal
printing mode after restart.
4-2. THE SELF-TESTING
Explanation: Printing the FW Version and DIP Switch
How to Print:
1. Click on the “Feed” to open “ Power switch” when the computer is off
2. Data will be printed and paused when this information shows up.
3. Press the “Feed” button again, the printer will conduct printing test
4. After printing is complete, trim the paper and end the printing process.
Page: 4-2
MP-1060 USER′S MANUAL
SOFTWARE
CONFIGURATION
CHAPTER
5
Helpful information that describes the settings for the display and
you’ll know how to install MP-1060 Utility step by step in this chapter
.
Sections include:
Ethernet Interface Card Setting
Printer Driver Setting
Page: 5-1
Chapter
5-1
5
Software Configuration
ETHERNET INTERFACE CARD SETTING
(1) Connect LAN cable to Ethernet interface card and turn on the Power.
(2) Open your Browser and Input default IP : 192.168.1.100
If you could not open the web page, please reset the interface card.
(IP return to the default value)
Default Setting:
IP Address: 192.168.1.100
Netmask: 255.255.255.0
Gateway : 192.168.2.254
BaudRate : 115200 bps
Local port : 9100
(3) Enter your settings (IP Address, Netmask, Gateway, BaudRate)
※BaudRate setting value must be 921600 bps
MP-1060 USER′S MANUAL
Page: 5-2
Chapter
5
Character Code Table
(4) Press the "Send" button, wait for the browser connection error.
(5) Input new IP in the browser
If you could open the web page, this configuration was successful.
If you could not open the web page, please go back to step (2).
MP-1060 USER′S MANUAL
Page: 5-3
Chapter
5-2
5
Software Configuration
PRINTER DRIVER SETTING
(1) Printer Driver Installation
(2) Setting Ports
(a)
Serial Port & USB Interface
Select the Serial Port: COM1
MP-1060 USER′S MANUAL
Page: 5-4
Chapter
5
Character Code Table
Configure Port
(b) Ethernet Interface
MP-1060 USER′S MANUAL
Page: 5-5
Chapter
5
Software Configuration
Add Port
MP-1060 USER′S MANUAL
Page: 5-6
Chapter
5
Character Code Table
Standard TCP/IP port
Type in IP address: 192.168.1.100 and Port Name: IP_192.168.1.100
MP-1060 USER′S MANUAL
Page: 5-7
Chapter
5
Software Configuration
Configure port, Protocol: Raw, Port Number: 9100
MP-1060 USER′S MANUAL
Page: 5-8
Chapter
5
Character Code Table
(3) Print Test Page
MP-1060 USER′S MANUAL
Page: 5-9
CHAPTER
COMMAND LIST
6
This chapter shows tables of character codes.
Note: All the tables only show the character configurations. They do
not show the actual print pattern.
Sections include:
Standard Command List
Two-Dimensional Bar Code Command Details
Kanji Control Command Details
Standard Command Details
Page: 6-1
Chapter
6-1
6 Command List
Standard Commands
Control
codes
<HT>
<LF>
<FF>
Hexadecimal
codes
09
0A
0C
<CR>
<CAN>
<DLE EOT>
<DLE ENQ>
<DLE DC4>
0D
18
10 04
10 05
10 14
<ESC FF>
<ESC SP>
<ESC !>
<ESC $>
<ESC *>
<ESC ->
<ESC 2>
<ESC 3>
<ESC =>
<ESC @>
<ESC D>
<ESC E>
<ESC G>
<ESC J>
<ESC L>
<ESC M >
<ESC R>
1B 0C
1B 20
1B 21
1B 24
1B 2A
1B 2D
1B 32
1B 33
1B 3D
1B 40
1B 44
1B 45
1B 47
1B 4A
1B 4C
1B 4D
1B 52
<ESC S>
<ESC T>
1B 53
1B 54
<ESC V>
1B 56
<ESC W>
<ESC \>
<ESC a>
<ESC c 3>
1B 57
1B 5C
1B 61
1B 63 33
MP-1060 USER′S MANUAL
Function
Horizontal tab
Print and line feed
Print and recover to standard
mode (in page mode)
Print and carriage return
Cancel print data in page mode
Real-time status transmission
Real-time request to printer
Real-time output of specified
pulse
Print data in page mode
Set right-side character spacing
Select print mode(s)
Set absolute print position.
Select bit image mode
Turn underline mode on/off.
Select default line spacing
Set line spacing
Select peripheral device
Initialize printer
Set horizontal tab position
Turn emphasized mode on/off
Turn double-strike mode on/off
Print and feed paper
Select page mode
Select character font
Select an international
character set
Select standard mode
Select print direction in page
mode
Turn 90 degree clockwise
rotation mode on/off
Set printing area in page mode
Set relative print position
Select justification
Select paper sensor(s) to
output paper-end signals
Standard
mode
○
○
Ignored
○
○
○
○
Ignored
○
○
○
○
○
○
○
○
Ignored
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
Ignored
○
○
Ignored
▲
○
○
○
▲
▲
○
○
○
▲
○
◎
◎
○
Page
mode
Page:6-2
Chapter
<ESC c 4>
1B 63 34
<ESC c 5>
<ESC d>
<ESC i>
<ESC m>
<ESC p>
<ESC t>
<ESC {>
1B 63 35
1B 64
1B 69
1B 6D
1B 70
1B 74
1B 7B
<FS p>
<FS q>
<GS !>
<GS $>
1C 70
1C 71
1D 21
1D 24
<GS *>
<GS ( A>
<GS ( K>
<GS />
<GS B>
1D 2A
1D 28 41
1D 28 4B
1D 2F
1D 42
<GS H>
1D 48
<GS I>
<GS L>
<GS P>
<GS V>
<GS W>
<GS \>
1D 49
1D 4C
1D 50
1D 56
1D 57
1D 5C
<GS a>
1D 61
<GS f>
<GS h>
<GS k>
<GS r>
<GS v 0>
<GS w>
1D 66
1D 68
1D 6B
1D 72
1D 76 30
1D 77
MP-1060 USER′S MANUAL
Select paper sensor(s) to stop
printing
Enable/disable panel buttons
Print and feed n lines
Full cut
Partial cut
General pulse
Select character code table
Turn upside-down printing
mode on/off
Print NV bit image
Define NV bit image
Select character size
Set absolute vertical print
position in page mode
Define download bit images
Execute test print
Set print density
Print download bit image
Turn white/black reverse
printing mode on/off
Select printing position of HRI
characters
Transmit printer ID
Set left margin
Set basic calculated pitch
Cut paper
Set printing area width
Set relative vertical print
position in page mode
Enable/disable Automatic
Status Back (ASB)
Select font for HRI characters
Set bar code height
Print bar code
Transmit status
Print raster bit image
Set bar code width
6 Command List
○
○
○
○
○
○
○
○
○
○
Disabled
Disabled
○
○
▲
○
Ignored
Disabled
Disabled
○
○
○
○
○
●
○
○
Disabled
Disabled
○
○
○
○
○
◎
○
◎
◎
Disabled
Disabled
○
○
▲
○
○
○
○
●
○
●
○
○
○
○
○
Disabled
○
◎
◎
Ignored
Page:6-3
Chapter
6-2
Two-dimensional Bar Code Commands
Control
codes
<DC2 ;>
Hexadecimal
codes
12 3B
<GS p 1>
1D 70 01
6-3
6 Command List
Function
Specifies a module size of QR
Code and Data Matrix
Prints QRCode data based on
the specified contents
Standard
mode
○
Page
mode
○
○
○
Kanji Control Commands
(When the Japanese, Simplified Chinese, Traditional Chinese, or Korean model is used)
Control
Hexadecimal
Function
Standard
Page
codes
codes
mode
mode
Set print mode(s) for Kanji
<FS !>
1C 21
○
○
characters
<FS &>
1C 26
Select Kanji character mode
○
○
Turn underline mode on/off
<FS ->
1C 2D
○
○
for Kanji characters
<FS .>
1C 2E
Cancel Kanji character mode
○
○
<FS S>
1C 53
Set Kanji character spacing
○
○
Turn
quadruple-size
mode
<FS W>
1C 57
○
○
on/off for Kanji characters
Command classification
Executing : Printer executes the command, which does not then affect the following
data.
Setting : Printer uses flags to make settings, and those settings affect the following data.
○: Enabled.
: Enabled only when the command is set at the beginning of a line.
●: Enabled only when data is not present in the printer buffer.
▲: Only value setting is possible.
Disabled: Parameters are processed as printable data.
Ignored: All command codes including parameters are ignored and nothing is executed.
◎
MP-1060 USER′S MANUAL
Page:6-4
Chapter
6.4
6 Command List
STANDARD COMMAND DETAILS
HT
[Name]
[Format]
[Range]
[Description]
Horizontal tab
ASCII
HT
Hex.
09
Decimal
9
N/A
Moves print position to next horizontal tab position.
This command is ignored if the next tab is not set.
If the next tab position exceeds the print region, the print position is
moved to [print region + 1].
The horizontal tab position is set by ESC D (Set/cancel horizontal tab
position).
When the print position is at the [print region + 1] position and this
command is received, the current line buffer full is printed and a horizontal tab is executed from the top of the next line.
The initial value of the horizontal tab position is every 8 characters of
Font A (the 9th, 17th, 25 positions, etc.)
th
LF
[Name]
[Format]
[Range]
[Description]
Print and line feed
ASCII
LF
Hex.
0A
Decimal
10
N/A
Prints the data in the print buffer and performs a line feed based on the
set line feed amount.
After execution, makes the top of the line the next print starting
position.
MP-1060 USER′S MANUAL
Page:6-5
Chapter
6 Command List
FF
[Name]
[Format]
[Range]
[Description]
Print and recover to standard mode (in page mode)
ASCII
FF
Hex.
0C
Decimal
12
N/A
Prints all buffered data to the print region collectively, then recovers
to the standard mode.
All buffer data is deleted after printing.
The print area set by ESC W (Set print region in page mode) is reset
to the default setting.
No paper cut is executed.
Sets the print position to the beginning of the next line after execution.
This command is enabled only in page mode.
CR
[Name]
[Format]
[Range]
[Description]
Print and carriage return
ASCII
CR
Hex.
0D
Decimal 13
N/A
When an automatic line feed is enabled, this command functions in the
same way as LF(print and line feed). When the automatic line feed is
disabled, this command is ignored.
This command is ignored with serial interface models.
Sets the print position to the beginning of the next line after execution.
CAN
[Name]
[Format]
Cancel print data in page mode
ASCII CAN
Hex. 18
Decimal 24
[Range]
N/A
[Description] Deletes all print data in the currently set print region in page mode.
This command is enabled only in page mode.
Portions included in the currently set print region are also deleted, even
if previously set print region data.
DLE EOT n
[Name]
[Format]
Real-time status transmission.
ASCII
OLE EOT n
MP-1060 USER′S MANUAL
Page:6-6
Chapter
[Range]
[Description]
6 Command List
Hex.
10
04
n
Decimal
16
4
n
1≤n≤4
Transmits the selected printer status specified by n in real time, according
to the following parameters:
n = 1 : Transmit printer status. n = 2 : Transmit off-line status.
n = 3 : Transmit error status. n = 4 : Transmit paper roll sensor status.
n = 1 : Printer status.
Bit On / Off Hex
0
Off
00
1
On
02
2
Off
00
On
04
3
Off
00
On
08
4
On
10
5
Off
00
6
Off
00
7
Off
00
Decimal
0
2
0
4
0
8
16
0
0
0
Function
Not used. Fixed to Off.
Not used. Fixed to On.
Drawer open/close signal is LOW.
Drawer open/close signal is HIGH.
On-line.
Off-line.
Not used. Fixed to On.
Not used. Fixed to Off.
Not used. Fixed to Off.
Not used. Fixed to Off.
n = 2 : Off-line status.
Bit On / Off Hex
0
Off
00
1
On
02
2
Off
00
On
04
3
Off
00
4
On
10
5
Off
00
On
20
6
Off
00
On
40
7
Off
00
Decimal
0
2
0
4
0
16
0
32
0
64
0
Function
Not used. Fixed to Off.
Not used. Fixed to On.
Cover is closed.
Cover is open.
Not used. Fixed to Off.
Not used. Fixed to On.
No paper-end stop.
Printing stops due to paper end.
No error.
Error occurs.
Not used. Fixed to Off.
n = 3 : Error status
Bit On / Off
0
Off
1
On
2
Off
3
Off
Decimal
0
2
0
0
Function
Not used. Fixed to Off.
Not used. Fixed to On.
Not used. Fixed to Off.
Not used. Fixed to Off.
MP-1060 USER′S MANUAL
Hex
00
02
00
00
Page:6-7
Chapter
4
5
6
7
On
Off
Off
Off
10
00
00
00
16
0
0
0
6 Command List
Not used. Fixed to On.
Not used. Fixed to Off.
Not used. Fixed to Off.
Not used. Fixed to Off.
n = 4 : Continuous paper sensor status.
Bit On / Off Hex Decimal Function
0
Off
00
0
Not used. Fixed to Off.
1
Off
02
2
Not used. Fixed to On.
2
Off
00
0
No paper-near-end stop.
On
04
4
Printing stops due to paper near
end.
3
Off
00
0
No paper-near-end stop.
On
08
8
Printing stops due to paper near
end.
4
On
10
16
Not used. Fixed to On.
5
Off
00
0
No paper-end stop.
On
20
32
Printing stops due to paper end.
6
Off
00
0
No paper-end stop.
On
40
64
Printing stops due to paper end.
7
Off
00
0
Not used. Fixed to Off.
MP-1060 USER′S MANUAL
Page:6-8
Chapter
6 Command List
DLE ENQ n
[Name]
[Format]
[Range]
[Description]
Real-time request to printer.
ASCII
DLE ENQ n
Hex.
10
05
n
Decimal
16
5
n
1≤n≤2
Responds to requests n specifications from the host in real-time. n specifications are below.
n = 1: Recover from the error and start printing from the line where the
error occurred.
n = 2: Recover from error after clearing the reception buffer and print
buffer.
This command is enabled even when the printer specification is disabled
by ESC = (select Peripheral devices).
DLE DC4 n m t
[Name]
[Format]
[Range]
[Description]
Real-time output of specified pulse.
ASCII
DLE DC4 n m t
Hex.
10
14
n m t
Decimal
16
20
n m t
n=1
m = 0,1
1≤t≤8
This outputs a signal specified by t to the connector pin specified by m.
m = 0: #2 Pin of the drawer kick connector
m = 1: #5 Pin of the drawer kick connector
On time is set to t x 100 msec; Off time is set to t x 100 msec.
MP-1060 USER′S MANUAL
Page:6-9
Chapter
6 Command List
ESC FF
[Name]
[Format]
Print data in page mode.
ASCII
ESC FF
Hex.
1B
0C
Decimal
27
12
[Range]
N/A
[Description] Prints all buffered data in the print area collectively in page mode.
This command is enabled only in page mode.
Holds the following information after printing.
a. Expanded data
b. Character print direction selection in page mode (ESC T)
c. Set print region (ESC W) in the page mode.
d. Character expansion position
ESC SP n
[Name]
[Format]
Set right-side character spacing.
ASCII
ESC SP
n
Hex.
1B
20
n
Decimal
27
32
n
[Range]
0 ≤ n ≤ 255
Initial Value n = 0
[Description] This command sets the size of space to right of character.
Right space = n × [horizontal motion units].
MP-1060 USER′S MANUAL
Page:6-10
Chapter
6 Command List
ESC ! n
[Name]
[Format]
[Range]
[Description]
Select print mode(s).
ASCII
ESC
!
n
Hex.
1B
21 n
Decimal
27
33 n
0 ≤ n ≤ 255
Initial Value n = 0
This command selects print mode(s) with bits having following meanings.
Bit On / Off Hex Decimal Function
0
Off
00
0
Character font A selected.
On
01
1
Character font B selected.
1
Off
00
0
Not used. Fixed to Off.
2
Off
00
0
Not used. Fixed to Off.
3
Off
00
0
Emphasized mode not selected.
On
08
8
Emphasized mode selected.
4
Off
00
0
Double-height mode not selected
On
10
16
Double-height mode selected
5
Off
00
0
Double-width mode not selected.
On
20
32
Double-width mode selected.
6
Off
00
0
Not used. Fixed to Off.
7
Off
00
0
Underline mode not selected.
On
80
128
Underline mode selected.
MP-1060 USER′S MANUAL
Page:6-11
Chapter
6 Command List
ESC $ nL nH
[Name]
[Format]
[Range]
[Description]
Set absolute print position.
ASCII
ESC
$
nL nH
Hex.
1B
24
nL nH
Decimal
27
36
nL nH
0 ≤ (nL + nH x 256) ≤ 65535 (0 ≤ nH ≤ 255, 0 ≤ nL ≤ 255)
This command specifies the next print starting position in reference to the
left edge of the print area. The printing start position is calculated using
(nL + nH x 256) x (vertical or horizontal motion units).
Specifications exceeding the print range are ignored.
ESC * m nL nH d1…dk
[Name]
[Format]
[Range]
Select bit image mode
ASCII
ESC * m nL nH d1...dk
Hex.
1B 2A m nL nH d1...dk
Decimal
27 42 m nL nH d1...dk
m = 0,1,32,33
0 ≤ nL ≤ 255
0 ≤ nH ≤ 3
0 ≤ d ≤ 255
Selects a bit-image mode in mode m for the number of dots specified by
nL and nH.
m = 1,33 : (nL+nH×256)<576 (3 inch);(nL+nH×256)<432 (2 inch).
m = 0,32 : (nL+nH×256)<288 (3 inch);(nL+nH×256)<216 (2 inch).
m
[Description]
0
1
32
33
Mode
8 dot single
density
8 dot double
density
24 dot single
density
24 dot double density
Number
of
Vert. Dir.
Dots
Density of
Vert.
Dir. Dots
Density
of Hor.
Dir. Dots
Data Count
(k)
8
67 DPI
101 DPI
nL+nH×256
8
67 DPI
203 DPI
nL+nH×256
24
203 DPI
101 DPI
24
203 DPI
203 DPI
(nL+nH×256)
×3
(nL+nH×256)
×3
ESC - n
[Name]
[Format]
Turn underline mode on/off.
ASCII
ESC
n
MP-1060 USER′S MANUAL
Page:6-12
Chapter
[Range]
[Description]
6 Command List
Hex.
1B 2D
n
Decimal
27
45
n
0≤n≤2
Initial Value n = 0
This command enables the print data following it to be printer out underlined.
The underline mode varied depending on the following values of n:
n
Function
0
Turns off underline mode
1
Turns on underline mode, set at 1-dot thick
2
Turns on underline mode, set at 2-dot thick
ESC 2
[Name]
[Format]
[Range]
[Description]
Select default line spacing.
ASCII
ESC 2
Hex.
1B 32
Decimal
27
50
N/A
This command sets the default line spacing The default line spacing is
approximately 4.25 mm, which is equivalent to 34 dots.
ESC 3 n
[Name]
[Format]
[Range]
[Description]
Set line spacing.
ASCII
ESC
3
n
Hex.
1B
33
n
Decimal
27
51
n
0 ≤ n ≤ 255
Initial Value n = 34
This command sets the line spacing using a following rule.
Line spacing = n x (vertical or horizontal motion units)
MP-1060 USER′S MANUAL
Page:6-13
Chapter
6 Command List
ESC = n
[Name]
[Format]
Select peripheral device.
ASCII
ESC
=
n
Hex.
1B
3D n
Decimal
27
61
n
[Range]
0 ≤ n ≤ 255
Initial Value n = 1
[Description] Selects the peripheral device for which the data is effective from the host
computer.
Bit
7
6
5
4
3
2
1
0
Function
Undefined
Undefined
Undefined
Undefined
Undefined
Undefined
Undefined
Printer
〝0 〞
〝1 〞
Invalid
Valid
ESC @
[Name]
[Format]
Initialize printer.
ASCII
ESC @
Hex.
1B
40
Decimal
27
64
[Range]
N/A
[Description] Clears data from the print buffer and sets the printer to its default settings.
MP-1060 USER′S MANUAL
Page:6-14
Chapter
6 Command List
ESC D n1…nk NUL
[Name]
[Format]
[Range]
[Description]
Set horizontal tab position
ASCII
ESC
D
n1...nk NUL
Hex.
1B
44
n1...nk NUL
Decimal
27
68
n1...nk NUL
1 ≤ n ≤ 255
0 ≤ k ≤ 32
Sets horizontal tab position
n specifies the column number for setting a horizontal tab position
from the left margin or the beginning of the line.
k indicates the number of horizontal tab positions to be set.
ESC E n
[Name]
[Format]
[Range]
[Description]
Turn emphasized mode on / off.
ASCII
ESC E
n
Hex.
1B
45
n
Decimal
27
69
n
0 ≤ n ≤ 255
Initial Value n = 0
This command turns emphasized mode on or off by toggling the least
significant bit of n like following.
When the LSB of n is 0, emphasized mode is turned off.
When the LSB of n is 1, emphasized mode is turned on.
ESC G n
[Name]
[Format]
[Range]
[Description]
Turn double-strike mode on/off.
ASCII
ESC G
n
Hex.
1B
47
n
Decimal
27
71
n
0 ≤ n ≤ 255
Initial Value n = 0
Specifies or cancels double printing.
Cancels double printing when n = <*******0>B.
Specifies double printing when n = <*******1>B.
n is effective only when it is the lowest bit.
This printer is not capable of double printing, so the print is the same
as when using emphasized printing.
This command is enabled for ANK characters
ESC J n
[Name]
[Format]
Print and feed paper.
ASCII
ESC J
MP-1060 USER′S MANUAL
n
Page:6-15
Chapter
[Range]
[Description]
6 Command List
Hex.
1B
4A n
Decimal
27
74
n
0 ≤ n ≤ 255
This command prints the data in the print buffer and feeds the paper [n X
vertical motion unit].
Sets the print position to the beginning of the next line after printing.
In standard mode, the printer uses the vertical motion unit (y).
In page mode, this command functions as follows, depending on the
starting position of the printable area:
(1)When the starting position is set to the upper left or lower right of the
printable area using ESC T, the vertical motion unit (y) is used.
(2)When the starting position is set to the upper right or lower left of the
print able area using ESC T, the horizontal motion unit (x) is used.
The maximum line spacing is 150mm {5.9 inches}. When the setting
value exceeds the maximum, it is converted to the maximum
automatically.
MP-1060 USER′S MANUAL
Page:6-16
Chapter
6 Command List
ESC L
[Name]
[Format]
[Range]
[Description]
Select page mode
ASCII
ESC L
Hex.
1B 4C
Decimal 27 76
N/A
Enabled only when input with the top of line.
Invalid when input by page mode.
Returns to standard mode after the following commands are issued.
a. FF (Print and recover to page mode)
b. ESC S (Select standard mode)
Character expansion position has the starting point specified by
ESC T (Character print direction selection in page mode) in the
printing region designated by the ESC W (Set print region in the page
mode) command.
This command switches the settings for the following commands
the values of which can be set independently in standard mode and
page mode to those for page mode
a. Set space amount: ESC SP, FS S
b. Set line feed amount: ESC 2, ESC 3
The following commands are enabled only when in page mode.
a. ESC V :Specify/cancel character 90 degree clockwise rotation
b. ESC a :Position alignment
c. ESC {
:Specify/cancel upside-down printing
d. GS W :Set print region width
The following command is ignored in page mode.
a. GS (A :Test print
The following commands are invalid in page mode.
a. FS p
:Print NV bit image
b. FS q
:Define NV bit image
c. GS v 0 :Print raster bit images
d. GS L
:Set left margin
Recover to standard mode using ESC @ (initialize printer).
MP-1060 USER′S MANUAL
Page:6-17
Chapter
6 Command List
ESC M n
[Name]
[Format]
[Range]
[Description]
Select character font.
ASCII
ESC M
n
Hex.
1B
4D
n
Decimal
27
77
n
n = 0, 1
Initial Value n = 0
This command selects ANK character fonts using n as following.
n
Function
0
Character font A selected
1
Character font B selected
ESC R n
[Name]
[Format]
[Range]
[Description]
Select an international character set.
ASCII
ESC R
n
Hex.
1B
52 n
Decimal
27
82 n
0 ≤ n ≤ 16
Initial Value n = 0
This command specifies international characters according to n values.
n
Character set
0
USA
1
France
2
Germany
3
UK
4
Denmark I
5
Sweden
6
Italy
7
Spain
8
Japan
9
Norway
10
Denmark II
11
Spain II
12
Latin America
13
Korea
14
Russia
15
Slavonic
16
User Define
ESC S
[Name]
[Format]
Select standard mode
ASCII ESC S
MP-1060 USER′S MANUAL
Page:6-18
Chapter
[Range]
[Description]
6 Command List
Hex.
1B 53
Decimal 27
83
N/A
Valid only when input by page mode.
All buffer data in page mode is deleted.
Sets the print position to the beginning of the next line after execution.
The print area set by ESC W (Set print region in page mode) is reset
to the default setting.
This command switches the settings for the following commands the
values of which can be set independently in standard mode and page
mode to those for standard mode
a. ESC SP :Set character right space amount
b. FS S :Set Chinese character space amount
c. ESC 2 :Set default line spacing
d. ESC 3 :Set line feed amount
The following commands are effective only when in standard mode.
a. ESC W :Set print region in page mode
b. ESC T :Select character print direction in page mode
The following commands are ignored in standard mode.
a. GS $ :Specify absolute position for character vertical direction in
page mode
b. GS \: :Specify relative position for character vertical direction in
page mode
Standard mode is selected when the power is turned on; the printer is
reset or initialized (ESC @).
MP-1060 USER′S MANUAL
Page:6-19
Chapter
6 Command List
ESC T n
[Name]
[Format]
[Range]
[Description]
Select print direction in page mode.
ASCII
ESC T n
Hex.
1B 54 n
Decimal 27 84 n
0 ≤ n ≤ 3, 48 ≤ n ≤ 51
Initial Value n = 0
Selects the character printing direction and starting point in page mode.
n
0, 48
Print Direction
Left to Right
1, 49
Bottom to Top
2, 50
Right to Left
3, 51
Top to Bottom
Starting Point
Upper Left
(A in the figure below)
Lower Left
(B in the figure below)
Lower Right
(C in the figure below)
Upper Right
(D in the figure below)
ESC V n
[Name]
[Format]
Turn 90 degree clockwise rotation mode on/off
ASCII ESC V n
MP-1060 USER′S MANUAL
Page:6-20
Chapter
[Range]
[Description]
6 Command List
Hex.
1B 56 n
Decimal 27
86 n
0 ≤ n≤ 1, 48≤ n ≤49
Initial Value n = 0
Specifies or cancels character 90 degree clockwise rotation.
n
Function
0, 48
Turns off 90 degree clockwise rotation mode
1, 49
Turns on 90 degree clockwise rotation mode


Underlines are not applied to characters rotated 90 degrees clockwise
even when ESC !,ESC - or FS - commands are given.
If 90 degree clockwise rotation is specified, double-wide and doubletall commands in the 90 rotation mode enlarges characters in the
opposite directions to double-wide and double-tall commands.
This command only affects printing in standard mode.
In page mode, this command is only effective for the setting.
This command is effective for ANK and Chinese characters.
MP-1060 USER′S MANUAL
Page:6-21
Chapter
6 Command List
ESC W xL xH yL yH dxL dxH dyL dyH
[Name]
[Format]
[Range]
[Description]
Set printing area in page mode
ASCII ESC W xL xH yL yH dxL dxH dyL dyH
Hex. 1B 57 xL xH yL yH dxL dxH dyL dyH
Decimal 27 87 xL xH yL yH dxL dxH dyL dyH
0 ≤ xL, xH, yL, yH, dxL, dxH, dyL, dyH ≤ 255
However, this excludes dxL = dxH = 0 or dyL = dyH = 0
Initial Value xL = xH = yL = yH = 0
Sets the print region position and size.
Horizontal direction starting point [(xL + xH x 256) x basic
calculated pitch]
Vertical direction starting point [(yL + yH x 256) x basic calculated
pitch]
Horizontal direction length [(dxL + dxH x 256) basic calculated
pitch]
Vertical direction length = [(dyL + dyH x 256) basic calculated
pitch]
(X+Dx-1)<576 (3 inch,basic calculated pitch=1);(X+Dx-1)<432 (2
inch,basic calculated pitch=1)
(Y+Dy-1)<768 (basic calculated pitch=1);
If (horizontal starting position + printing area width) exceeds the
printable area, the printing area width is automatically set to (horizontal
printable area - horizontal starting position).
If (vertical starting position + printing area height) exceeds the
printable area, the printing area height is automatically set to (vertical
printable area - vertical starting position).
MP-1060 USER′S MANUAL
Page:6-22
Chapter
6 Command List
ESC \ nL nH
[Name]
[Format]
[Range]
[Description]
Set relative print position.
ASCII
ESC \
nL nH
Hex.
1B
5C nL nH
Decimal
27
92
nL nH
0 ≤ (nL + nH x 256) ≤ 65535 (0 ≤ nL 255, 0 ≤ nH ≤ 255)
Specifies the next print starting position with a relative position based
on the current position. This sets the position from the current position
to [(nL + nH x 256) x basic calculated pitch] for the next print starting
position.
Specifications exceeding the print range are ignored..
ESC a n
[Name]
[Format]
[Range]
[Description]
Select justification.
ASCII
ESC a n
Hex.
1B
61 n
Decimal
27
97 n
0 ≤ n ≤2
Initial Value n = 0
This command specifies position alignment for all data in one line in
standard mode, using n as follows:
n
0
1
2
Alignment
Left alignment
Center alignment
Right alignment
This command has no effect in page mode.
MP-1060 USER′S MANUAL
Page:6-23
Chapter
6 Command List
ESC c 3 n
[Name]
[Format]
[Range]
[Description]
Select paper sensor(s) to output paper-end signals.
ASCII
ESC
c
3 n
Hex.
1B
63
33 n
Decimal
27
99
51 n
Specification: 0 ≤ n ≤ 3
Initial Value n = 0
Selects paper out detector that outputs a paper out signal when paper has
run out.
Bit Function
0
1
7
Undefined
6
Undefined
5
Undefined
4
Undefined
3
Undefined
2
Undefined
1
Paper roll near end detector
Invalid
Valid
0
Paper roll near end detector
Invalid
Valid
〝〞 〝〞
ESC c 4 n
[Name]
[Format]
[Range]
[Description]
Select paper sensor(s) to stop printing.
ASCII
ESC
c
4
n
Hex.
1B
63
34
n
Decimal
27
99
52
n
Specification: 0 ≤ n ≤ 3
Initial Value n = 0
Selects the paper out detector to stop printing when paper has run out.
Bit Function
0
1
7
Undefined
6
Undefined
5
Undefined
4
Undefined
3
Undefined
2
Undefined
1
Paper roll near end detector
Invalid Valid
0
Paper roll near end detector
Invalid Valid
〝〞 〝〞
ESC c 5 n
[Name]
[Format]
Enable/disable panel buttons
ASCII
ESC
c
5
Hex.
1B
63
35
MP-1060 USER′S MANUAL
n
n
Page:6-24
Chapter
[Range]
[Description]
6 Command List
Decimal
27
99
53
n
Specification: 0 ≤ n ≤ 255
Initial Value n = 0
Toggles the panel switches between enabled and disabled.
Enables panel switches when n = <*******0>B.
Disables panel switches when n = <*******1>B.
n is effective only when it is the lowest bit.
When disabled, all panel switches are disabled.
ESC d n
[Name]
[Format]
[Range]
[Description]
Print and feed n lines
ASCII
ESC
d
n
Hex.
1B
64
n
Decimal
27
100
n
0 ≤ n ≤ 255
Prints the data in the print buffer and performs a paper feed of n lines.
Sets the print position to the beginning of the next line after printing.
Paper is fed approximately 150 mm if the [n x basic calculated pitch]
exceeds approximately 150 mm (5.9 inches).
ESC i
[Name]
[Format]
[Range]
[Description]
Full cut.
ASCII
ESC
i
Hex.
1B
69
Decimal
27
105
N/A
This command executes a full cut of the paper in standard mode
MP-1060 USER′S MANUAL
Page:6-25
Chapter
6 Command List
ESC m
[Name]
[Format]
[Range]
[Description]
Partial cut.
ASCII
ESC
m
Hex.
1B
6D
Decimal
27
109
N/A
This command executes a partial cut of the paper with one point uncut in
standard mode.
ESC p m t1 t2
[Name]
[Format]
[Range]
[Description]
General pulse.
ASCII
ESC
p
m
t1
t2
Hex.
1B
70
m
t1
t2
Decimal
27
112
m
t1
t2
0 ≤ m ≤ 1, 48 ≤ m ≤ 49
0 ≤ t1 ≤ 255
0 ≤ t2 ≤ 255
This outputs a signal specified by t1 and t2 to the connector pin specified
by m.
Drawer kick on time is set to t1 x 2 ms; off time is set to t2 x 2 ms.
m
0, 48
1, 49
Connector Pin
Drawer kick connector pin #2
Drawer kick connector pin #5
t1
MP-1060 USER′S MANUAL
t2
Page:6-26
Chapter
6 Command List
ESC t n
[Name]
[Format]
[Range]
[Description]
Select character code table.
ASCII
ESC
t
n
Hex.
1B
74
n
Decimal
27
116
n
0≤n≤8
Initial Value n = 0
Select page n of the character code table.
n
Character set
0
CP-437
1
Katakana
2
CP-850
3
CP-852
4
CP-860
5
CP-863
6
CP-865
7
CP-1252
8
User Define
ESC { n
[Name]
[Format]
[Range]
[Description]
Turns upside-down printing mode on/off.
ASCII
ESC
{
n
Hex.
1B
7B n
Decimal
27
123 n
0 ≤ n ≤ 255
Initial Value n = 0
Specifies or cancels upside-down printing.
Cancels upside-down printing when n = <*******0>H.
Specifies upside-down printing when n = <*******1>H.
n is effective only when it is the lowest bit.
This command is effective only when input at the top of the line when
standard mode is being used.
This command has no affect in page mode. In page mode, this command is only effective for the setting.
Upside-down printing rotates line data 180 degrees.
n
Upside-down mode
0
Turned off
1
Turned on
MP-1060 USER′S MANUAL
Page:6-27
Chapter
6 Command List
FS p n m
[Name]
[Format]
[Range]
[Description]
Print NV bit image.
ASCII
FS
p
n
m
Hex.
1C
70
n
m
Decimal
28
112
n
m
1 ≤ n ≤ 255
0 ≤ m ≤ 3, 48 ≤ m ≤ 51
Prints NV bit image n using mode m.
m
Mode
0, 48
Nornal
1, 49
Double-width
2, 50
Double-height
3, 51
Quadruple
n specifies the NV bit image number.
m specifies the bit-image mode.
NV bit image is a bit image defined in non-volatile memory by FS q
and printed by this command.
This command is ignored when the specified NV bit image n is undefined.
This command is effective only when no data exists in the print buffer
in standard mode.
MP-1060 USER′S MANUAL
Page:6-28
Chapter
6 Command List
FS q n [xL xH yL yH d1…dk]1…[xL xH yL yH
d1…dk]n
[Name]
[Format]
[Range]
[Description]
Define NV bit image.
ASCII
FS
q
n
[xL xH yL yH d1…dk]1…[xL xH yL
yH d1…dk]n
Hex.
1C
71
n
[xL xH yL yH d1…dk]1…[xL xH yL
yH d1…dk]n
Decimal
28
113 n
[xL xH yL yH d1…dk]1…[xL xH yL yH
d1…dk]n
1 ≤ n ≤ 255
1 ≤ (xL + xH ×256) ≤ 54 (0 ≤ xL ≤ 54, xH=0) for 2 inch
1 ≤ (xL + xH ×256) ≤ 72 (0 ≤ xL ≤ 72, xH=0) for 3 inch
1 ≤ (yL + yH ×256) ≤ 96 (0 ≤ yL ≤ 96, yH=0)
0 ≤ d ≤ 255
k = (xL + xH × 256) × (yL + yH × 256) × 8
Defines the specified NV bit image.
n specifies the number of NV bit images to define.
xL and xH specify the horizontal direction for one NV bit image (xL +
xH x 256) x 8 dots.
yL and yH specify the vertical direction for one NV bit image (yL +
yH x 256) x 8 dots.
MP-1060 USER′S MANUAL
Page:6-29
Chapter
6 Command List
GS ! n
[Name]
[Format]
[Range]
[Description]
Select character size.
ASCII
GS
!
n
Hex.
1D
21
n
Decimal
29
33
n
0 ≤ n ≤ 255
(1 ≤ Vertical enlargement ≤ 8, 1 ≤ Horizontal enlargement ≤ 8)
Initial Value n = 0
This command selects the character height and width using bits 0 to 3, and
bits 4 to 7 respectively as follows:
Bit
0
1
2
3
4
5
6
7
Function
Specifies the number of times
normal font size in the vertical
direction
Setting
Refer to Table 2
[Enlarged in vertical
direction]
Specifies the number of times Refer to Table 1
normal font size in the horizon- [Enlarged in horizontal
tal direction
direction]
Table 1 [Enlarged in horizontal direction]
Hex Decimal Enlargement
00
0
1 time(standard)
10
16
2 times
20
32
3 times
30
48
4 times
40
64
5 times
50
80
6 times
60
96
7 times
70
112
8 times
Table 2 [Enlarged in vertical direction]
Hex Decimal Enlargement
00
0
1 time(standard)
01
1
2 times
02
2
3 times
03
3
4 times
04
4
5 times
05
5
6 times
06
6
7 times
07
7
8 times
MP-1060 USER′S MANUAL
Page:6-30
Chapter
6 Command List
GS $ nL nH
[Name]
[Format]
[Range]
[Description]
Set absolute vertical print position in page mode
ASCII
GS
$
nL
nH
Hex.
1D
24
nL
nH
Decimal
29
36
nL
nH
0 ≤ nL ≤ 255, 0 ≤ nH ≤ 255,
Specifies the character vertical direction position for the data expansion
starting position using the absolute position based on the starting point
in page mode. The position of the character vertical direction for the
next data expansion starting position is the position specified by [(nL +
nH x 256) x basic calculated pitch] from the starting point.
When not in page mode, this command is ignored.
Specifications for absolute positions that exceed the specified print
range are ignored.
MP-1060 USER′S MANUAL
Page:6-31
Chapter
6 Command List
GS * X
Y [d1…d(X x Y x 8)]
[Name]
[Format]
Define download bit images.
ASCII
GS
*
X
Y [d1…d(X x Y x 8)]
Hex.
1D
2A
X
Y [d1…d(X x Y x 8)]
Decimal
29
42
X
Y
[d1…d(X x Y x 8)]
1 ≤ X ≤ 54 (for 2 inch)
1 ≤ X ≤ 72 (for 3 inch)
1 ≤ Y ≤ 96
0 ≤ d ≤ 255
Defines the download bit image of the number of dots specified by X
and Y.
X specifies the number of bytes in the horizontal direction.
Y specifies the number of bytes in the vertical direction.
Horizontal direction dot count is X x 8 dots; Vertical direction dot
count is Y x 8 dots
d indicates the bit-image data.
Bits that correspond to the dots to print are 1, and the bits that correspond to the dots that are not printed are 0.
[Range]
[Description]
MP-1060 USER′S MANUAL
Page:6-32
Chapter
6 Command List
GS ( A pL pH n m
[Name]
[Format]
[Range]
[Description]
Execute test print.
ASCII
GS (
A pL
pH
n
m
Hex.
1D 28
41
pL
pH
n
m
Decimal
29 40
65 pL
pH
n
m
{pL+ (pH×256) } = 2 (pL = 2,pH = 0)
0 ≤ n ≤ 2 , 48 ≤ n ≤ 50
2 ≤ m ≤ 3 , 50 ≤ m ≤ 51
Executes the specified test print.
The following command is ignored in page mode.
Specifies the parameter count following pL and pH in (pL + (pH x 256))
bytes.
n specifies the paper to be tested.
n
Paper Type
0 , 48
Basic sheet (paper roll)
1 , 49
Paper Roll
2 , 50
m specifies a test pattern..
m
2 , 50
3 , 51
Type of Test Print
Printer Status (Self Print)
Rolling Pattern Print
GS ( K pL pH n m
[Name]
[Format]
[Range]
Set print density.
ASCII
GS
(
A pL
pH
Hex.
1D 28
4B pL
pH
Decimal
29 40
75
pL
pH
{pL+ (pH×256) } = 2 (pL = 2,pH = 0)
n = 49
250 ≤ m ≤ 255, 0 ≤ m ≤ 6
Initial Value m = 0
MP-1060 USER′S MANUAL
n
n
n
m
m
m
Page:6-33
Chapter
[Description]
6 Command List
Sets print density..
m
250
251
252
253
254
255
0
1
2
3
4
5
6
Print Density
0.7
0.7
0.8
0.8
0.9
0.9
1.0
1.1
1.1
1.2
1.2
1.3
1.3
GS / m
[Name]
[Format]
[Range]
[Description]
Print downloaded bit image.
ASCII
GS
/
m
Hex.
1D 2F m
Decimal
29 47 m
0 ≤ m ≤ 3, 48 ≤ m ≤ 51
This command prints the downloaded bit image defined by GS * according to the mode denoted by m.
m
Mode
0,
48
1,
49
2,
50
3,
51
Normal
Vertical dot
density(DPI)
203
Horizontal dot
density(DPI)
203
Double-width 203
101
Doubleheight
Quadruple
101
203
101
101
GS B n
[Name]
Turn white/black reverse printing mode on/off
MP-1060 USER′S MANUAL
Page:6-34
Chapter
[Format]
[Range]
[Description]
6 Command List
ASCII
GS
B n
Hex.
1D 42 n
Decimal
29 66 n
0 ≤ n ≤ 255
Initial Value n = 0
Specifies or cancels black and white inverted printing.
Cancels black and white inverted printing when n = <*******0>B.
Specifies black and white inverted printing when n = <*******1>B.
n is effective only when it is the lowest bit.
Internal characters and download characters are targeted for black and
white inverted printing.
This command is effective for ANK and Chinese characters.
GS H n
[Name]
[Format]
[Range]
[Description]
Select printing position of HRI characters.
ASCII
GS
H
n
Hex.
1D 48
n
Decimal
29 72
n
0 ≤ n ≤ 3, 48 ≤ n ≤ 51
Initial Value n = 0
Selects the printing position of HRI characters when printing bar codes.
m
0, 48
1, 49
2, 50
3, 51
MP-1060 USER′S MANUAL
Printing Position
No print
Above bar code
Below bar code
Above and below bar code(both)
Page:6-35
Chapter
6 Command List
GS I n
[Name]
[Format]
[Range]
[Description]
Transmit printer ID.
ASCII
GS
I
n
Hex.
1D 49 n
Decimal
29 73 n
1 ≤ n ≤ 3, 49 ≤ n ≤ 51, 65 ≤ n ≤ 69
Transmits the printer ID specified by n as follows:
MP-1060 USER′S MANUAL
n
1, 49
2, 50
3, 51
Printer ID Type
Model ID
Type ID
ROM Version ID
65
Firmware Version
66
Manufacturer Name
67
68
Model Name
Serial Number
69
Chinese Character
Types
Specifications
MB-1030 or MP-1060
1030-XX or 1060-XX
Depends on the ROM
version
Depends on the firmware
version
MB-1030 System or
MP-1060 System
MB-1030 or MP-1060
Depends on the serial
number
Taiwan Language
Characters:
TW_BIG5
Japanese Language
Characters:
JP_SJIS
Chinese Language
Characters:
CN_GB2312
Korean Language
Characters:
KO_EUC-KR
Page:6-36
Chapter
6 Command List
GS L nL nH
[Name]
[Format]
[Range]
[Description]
GS P x
[Name]
[Format]
[Range]
[Description]
Set left margin.
ASCII
GS
L
nL
nH
Hex.
1D 4C nL
nH
Decimal
29 76
nL
nH
0 ≤ nL ≤ 255, 0 ≤ nH ≤ 255
Initial Value (nL + nH x 256)=0 (nL=0, nH=0)
nL and nH set the specified left margin.
The left margin is [(nL + nH x 256) x basic calculated pitch].
y
Set basic calculated pitch.
ASCII
GS P
x
Hex.
1D 50
x
Decimal
29 80
x
0 ≤ x ≤ 255
0 ≤ y ≤ 255
y
y
y
Initial Value x = 203, y = 203: EPSON targeted model print head 203
DPI
Sets the horizontal basic calculated pitch to approximately 25.4/xmm
[(1/x) inch], and the vertical basic calculated pitch to approximately
25.4/ymm [(1/y) inch].
x = 0: Returns the horizontal basic calculated pitch to its default value.
y = 0: Returns the vertical basic calculated pitch to its default value.
GS V m
[Name]
[Format]
Cut paper.
ASCII
MP-1060 USER′S MANUAL
GS
V
m
(n)
Page:6-37
Chapter
[Range]
[Description]
6 Command List
Hex.
1D 56
m (n)
Decimal
29 86
m (n)
m = 0,1,48,49,65,66 0 ≤ n ≤ 255
Executes specified paper cut.
m
0 , 48
1 , 49
65
66
Function
Full cut
Partial cut (one point uncut)
Feeds paper to (cutting position + [n x basic
calculated pitch]) and performs a full cut
Feeds paper to (cutting position + [n x basic
calculated pitch]) and performs a partial cut
(one point uncut)
GS W nL nH
[Name]
[Format]
[Range]
[Description]
Set printing area width.
ASCII
GS
W
nL nH
Hex.
1D
57
nL nH
Decimal
29
87
nL nH
0 ≤ nL ≤ 255, 0 ≤ nH ≤ 255
Sets the print region width specified by nL and nH.
Print region width is [(nL + nH x 256) x basic calculated pitch].
[(nL + nH x 256) x basic calculated pitch] >=24.
MP-1060 USER′S MANUAL
Page:6-38
Chapter
6 Command List
GS \ nL nH
[Name]
[Format]
[Range]
[Description]
Set relative vertical print position in page mode.
ASCII
GS
\
nL nH
Hex.
1D
5C nL nH
Decimal
29
92
nL nH
0 ≤ nL ≤ 255
0 ≤ nH ≤ 255
Specifies the character vertical direction position for the data expansion
starting position using the relative position based on the current point in
page mode. This sets the position moved from the current position to
[(nL + nH x 256) x basic calculated pitch] for the next data expanding
starting position.
When not in page mode, this command is ignored.
GS a n
[Name]
[Format]
[Range]
Enable/disable Automatic Status Back (ASB).
ASCII
GS
a
n
Hex.
1D
61 n
Decimal
29
97 n
0 ≤ n ≤ 255
Initial Value n = 0
MP-1060 USER′S MANUAL
Page:6-39
Chapter
[Description]
6 Command List
Selects the statuses that are targeted for transmission with the automatic
status function (ASB: Automatic Status Back).
Bits
7
6
5
4
3
2
1
0
Statuses Targeted for
ASB
Undefined
Undefined
Undefined
Undefined
Continuous Paper Detector
Error
ONLINE/OFFLINE
Status
“0”
“1”
--------Invalid
--------Valid
Invalid
Invalid
Valid
Valid
Drawer kick connector pin
#3
Invalid
Valid
The printer information transmitted is comprised of 4 bytes as follows:
First byte(printer information)
Bit
Off/On
Hex Decimal
Function
7
Off
00
0
Not used. Fixed to Off
6
Off
00
0
Paper is not being fed by the
paper feed button
On
40
64
Paper is being fed by the
paper feed button
5
Off
00
0
Cover is close
On
20
32
Cover is open
4
On
10
16
Not used. Fixed to On
3
Off
00
0
On-line
On
08
8
Off-line
2
0
Drawer kick-out connector
Off
00
pin 3 is LOW
4
Drawer kick-out connector
On
04
pin 3 is HIGH
1
Off
00
0
Not used. Fixed to Off
0
Off
00
0
Not used. Fixed to Off
Bit
7
Second byte(printer information)
Off/On
Hex Decimal
Function
Off
00
0
Not used. Fixed to Off
MP-1060 USER′S MANUAL
Page:6-40
Chapter
6
5
4
3
2
1
0
Bit
7
6
5
4
2,3
0,1
Bit
7
6
5
4
3
2
1
0
6 Command List
Off
00
0
Not used. Fixed to Off
Off
00
0
Not used. Fixed to Off
Off
00
0
Not used. Fixed to Off
On
08
8
Not used. Fixed to Off
4
Not used. Fixed to Off
On
04
On
02
2
Not used. Fixed to Off
On
01
1
Not used. Fixed to Off
Third byte (paper sensor information)
Off/On
Hex Decimal
Function
Off
00
0
Not used. Fixed to Off
Off
00
0
Not used. Fixed to Off
Off
00
0
Not used. Fixed to Off
On
00
0
Not used. Fixed to Off
Off
00
0
Paper end sensor: paper present
On
0C
12
Paper end sensor: no paper
present
Off
00
0
Paper near end sensor: paper
adequate
On
03
3
Paper near end sensor: paper
near end
Fourth byte (paper sensor information)
Off/On
Hex Decimal
Function
Off
00
0
Not used. Fixed to Off
Black mark sensor status
Off
00
0
Off
00
0
Not used. Fixed to Off
Off
00
0
Not used. Fixed to Off
On
08
8
Not used. Fixed to On
4
Not used. Fixed to On
On
04
On
02
2
Not used. Fixed to On
On
01
1
Not used. Fixed to On
MP-1060 USER′S MANUAL
Page:6-41
Chapter
6 Command List
GS f n
[Name]
[Format]
[Range]
[Description]
Select font for HRI characters.
ASCII
GS
f
n
Hex.
1D
66
n
Decimal
29
102
n
n = 0,1,48,49
Initial Value n = 0
Selects the HRI character font when printing bar codes.
n
0, 48
1, 49
Font
Selects Font A (12 x 24).
Selects Font B (9 x 17).
GS h n
[Name]
[Format]
[Range]
[Description]
Set bar code height.
ASCII
GS
h
n
Hex.
1D
68
n
Decimal
29
104
n
1 ≤ n ≤ 255
Initial Value n = 162
Sets bar code height to n dots.
1. GS k m d1 … dk NUL.
2. GS k m n d1 … dk
[Name]
[Format]
[Range]
[Description]
Print bar code.
1. ASCII
GS
k
m d1...dk NUL
Hex.
1D 6B m d1...dk NUL
Decimal
29 107 m d1...dk NUL
2. ASCII
GS
k
m n d1...dk
Hex.
1D 6B
m n d1...dk
Decimal
29 107 m n d1...dk
1. 0 ≤ m ≤ 6 The definition region of k and d differ according to the bar
code type.
2. 65 ≤ m ≤ 73 The definition region of n and d differ according to the bar
code type.
Selects bar code type and prints bar codes.
1:
m
Bar Code Type
Defined region of k Defined region of d
MP-1060 USER′S MANUAL
Page:6-42
Chapter
0
1
2
3
4
UPC-A
UPC-E
JAN13 (EAN13)
JAN8 (EAN8)
CODE39
11 ≤ k ≤ 12
11 ≤ k ≤ 12
12 ≤ k ≤ 13
7≤k≤8
1 ≤ k ≤ 255
5
ITF
6
CODABAR
2 ≤ k ≤ 254 (However, this is an even
number.)
1 ≤ k ≤ 255
2:
m
65
66
67
68
69
Bar Code Type
UPC-A
UPC-E
JAN13 (EAN13)
JAN8 (EAN8)
CODE39
Defined region of n
11 ≤ n ≤ 12
11 ≤ n ≤ 12
12 ≤ n ≤ 13
7≤n≤8
1 ≤ n ≤ 255
70
ITF
71
CODABAR
72
73
CODE93
CODE128
MP-1060 USER′S MANUAL
6 Command List
48 ≤ d ≤ 57
48 ≤ d ≤ 57
48 ≤ d ≤ 57
48 ≤ d ≤ 57
48 ≤ d ≤ 57, 65 ≤ d ≤
90,
32, 36, 37, 43, 45, 46,
47
48 ≤ d ≤ 57
48 ≤ d ≤ 57, 65 ≤ d ≤
68,
36, 43, 45, 46, 47, 58
Defined region of d
48 ≤ d ≤ 57
48 ≤ d ≤ 57
48 ≤ d ≤ 57
48 ≤ d ≤ 57
48 ≤ d ≤ 57, 65 ≤ d ≤
90,
32, 36, 37, 43, 45, 46,
47
2 ≤ n ≤ 254 (How- 48 ≤ d ≤ 57
ever, this is an even
number.)
1 ≤ n ≤ 255
48 ≤ d ≤ 57, 65 ≤ d ≤
68,
36, 43, 45, 46, 47, 58
1 ≤ n ≤ 255
0 ≤ d ≤ 127
2 ≤ n ≤ 255
0 ≤ d ≤ 127
Page:6-43
Chapter
6 Command List
GS r n
[Name]
[Format]
[Range]
[Description]
Transmit status.
ASCII
GS
r
n
Hex.
1D
72
n
Decimal
29
114 n
n = 1, 2, 49, 50
Sends the specified status.
Detector Status (n=1,49)
Bit
Status
0
7
Fixed at 0
6
Undefined
5
Undefined
4
Fixed at 0
3
Paper roll end detector
Has Paper
2
Paper roll end detector
Has Paper
1
Paper roll near end detector Has Paper
0
Paper roll near end detector Has Paper
Drawer Kick Connector Status (n=2,50)
Bit
Status
0
7
Fixed at 0
6
Undefined
5
Undefined
4
Fixed at 0
3
Undefined
2
Undefined
1
Undefined
0
Drawer kick connector pin
L
#3
〝〞
〝1 〞
Paper out
Paper out
Paper out
Paper out
〝〞
〝1 〞
〝〞
〝 H〞
GS v 0 m xL xH yL yH d1 … dk
[Name]
[Format]
[Range]
Print raster bit image.
ASCII
GS
v
Hex.
1D
76
Decimal
29
118
m = 0, m = 48
0 ≤ xL ≤ 54(for 2 inch)
0 ≤ xL ≤ 72(for 3 inch)
MP-1060 USER′S MANUAL
0
30
48
m xL
xH
yL
yH d1...dk
m xL
xH
yL
yH d1...dk
m xL
xH
yL
yH d1...dk
Page:6-44
Chapter
[Description]
6 Command List
0 ≤ xH ≤ 0
0 ≤ yL ≤ 255
0 ≤ yH ≤ 3
0 ≤ d ≤ 255
k = (xL+xH×256) × (yL+yH×256) However, k ≠ 0
Prints raster method bit images using mode m.
m
Mode
0, 48
Normal Mode
Density of Vert. Dir. Density of Hor. Dir.
Dots
Dots
203 DPI
203 DPI
xL and xH specify the horizontal direction data count for one bit image (xL + xH x 256) in bytes.
yL and yH specify the vertical direction data count for one bit image
(yL + yH x 256) in bytes.
MP-1060 USER′S MANUAL
Page:6-45
Chapter
6 Command List
GS w n
[Name]
[Format]
[Range]
[Description]
Set bar code width.
ASCII
GS
w
n
Hex.
1D
77
n
Decimal
29 119 n
1≤n≤6
Initial Value n = 2
Sets the bar code horizontal size.
n
1
2
3
4
5
6
Multi-level Bar
Code Module
Width [mm]
0.141
0.282
0.423
0.564
0.706
0.847
Binary Level Bar Code
Fine Element
Thick Element
Width[mm]
Width[mm]
0.141
0.423
0.282
0.706
0.423
1.129
0.564
1.411
0.706
1.834
0.847
2.258
TWO-DIMENSIONAL BAR CODE COMMAND DETAILS
DC2 ; n
[Name]
[Format]
[Range]
[Description]
QR Code Module Size Set
ASCII
DC
;
n
Hex.
12
3B
n
Decimal
18
59
n
2 ≤ n ≤ 16
Initial Value n = 2
Specifies a module size of QR Code and Data Matrix.
n: The number of dots for one side of the module size.
MP-1060 USER′S MANUAL
Page:6-46
Chapter
6 Command List
GS p 1
[Name]
[Format]
[Range]
[Description]
QR Code Print
ASCII
GS
p
1 model e v mode nl nh [data]
Hex.
1D
70
01 model e v mode nl nh [data]
Decimal
29 112 01 model e v mode nl nh [data]
model=01, 02
e=4Ch, 4Dh, 51h, 48h
0, 1 ≤ v ≤ 40
mode=4Eh, 41h, 42h, 4Bh, 4Dh
1≤ nh×256+nl≤ 7089
Prints QRCode data based on the specified contents.
model: Specifies a model
e: Selects an error correction level.
’L’ (4CH), ’M’ (4DH), ’Q’ (51H), ’H’ (48H)
v: =0: Automatic selection
(A version is automatically selected depending on the number of
input data.)
1 ≤ v ≤ 40 Fixed version (up to 14 for model-1)
mode: Specifies a mode of data.
Mode
Hexadecimal
N
4E
A
41
B
42
K
4B
M
4D
nl, nh: Specifies the number of data.
Mode
Numerical mode
Alphanumeric mode
8-bit byte mode
Kanji mode
Mixed mode
Data: Kanji data of the QRCode data should be set by Shift JIS code.
MP-1060 USER′S MANUAL
Page:6-47
Chapter
6 Command List
KANJI CONTROL COMMAND DETAILS
FS ! n
[Name]
[Format]
[Range]
[Description]
Set print mode(s) for Kanji characters.
ASCII
FS
!
n
Hex.
1C
21
n
Decimal
28
33
n
0 ≤ n ≤ 255
Initial Value n = 0
Batch specifies the Kanji character print mode.
Bit
7
6
5
4
3
2
1
0
Function
Underline
Undefined
Undefined
Undefined
Double tall expanded
Expanded wide
Undefined
Undefined
〝0 〞 〝1 〞
Off
On
Off
Off
On
On
FS &
[Name]
[Format]
[Range]
[Description]
Select Kanji character mode.
ASCII
FS
&
Hex.
1C
26
Decimal
28
38
N/A
Specifies Kanji character mode.
MP-1060 USER′S MANUAL
Page:6-48
Chapter
6 Command List
FS - n
[Name]
[Format]
[Range]
[Description]
Turn underline mode on/off for Kanji characters
ASCII
FS
n
Hex.
1C
2D
n
Decimal
28
45
n
0 ≤ n ≤ 2, 48 ≤ n ≤ 50
Specifies or cancels Kanji character underlines.
n
Function
0,48 Cancels Kanji character underline
1,49 Sets to one-dot width Kanji character underline and
specifies Kanji character underlines.
2,50 Sets to two-dot width Kanji character underline and
cancels Kanji character underlines.
FS .
[Name]
[Format]
[Range]
[Description]
Cancel Kanji character mode.
ASCII
FS
.
Hex.
1C
2E
Decimal
28
46
N/A
Cancels Kanji character mode.
FS S n1 n2
[Name]
[Format]
[Range]
[Description]
Set Kanji character spacing
ASCII
FS
S
n1
n2
Hex.
1C
53
n1
n2
Decimal
28
83
n1
n2
0 ≤ n1 ≤ 255, 0 ≤ n2 ≤ 255
Initial Value n1 = 0, n2=0
Sets the Kanji character space amount and right space amount.
Left space amount: n1 x (basic calculated pitch)
Right space amount: n2 x (basic calculated pitch)
MP-1060 USER′S MANUAL
Page:6-49
Chapter
FS
W
[Name]
[Format]
[Range]
[Description]
6 Command List
n
Turn quadruple-size mode on/off for Kanji characters.
ASCII
FS
W
n
Hex.
1C
57
n
Decimal
28
87
n
0 ≤ n ≤ 255
Initial Value n = 0
Specifies or cancels quadruple size Kanji character.
Cancels quadruple size when n = <*******0>B.
Specifies quadruple size when n = <*******1>B.
n is effective only when it is the lowest bit.
MP-1060 USER′S MANUAL
Page:6-50
CHAPTER
LANGUAGES
7
This chapter shows tables of character codes.
Note: All the tables only show the character configurations. They do
not show the actual print pattern.
Sections include:
Ank Code Page
INTERNATIONAL CHARACTERS
Japanese Language Codes (Shift-JIS Codes)
Taiwanese Language Codes
Simplified Chinese Language Codes
Korean Language Codes
Page: 7-1
Chapter
7-1
7 Languages
Ank Codes
MP-1060 USER′S MANUAL
Page: 7-2
Chapter 7 Languages
MP-1060 USER′S MANUAL
Page:7-3
Chapter
MP-1060 USER′S MANUAL
7 Languages
Page: 7-4
Chapter 7 Languages
7-2
International Characters
MP-1060 USER′S MANUAL
Page:7-5
Chapter
7-3
7 Languages
Japanese Language Codes (Shift-JIS Codes)
MP-1060 USER′S MANUAL
Page: 7-6
Chapter 7 Languages
MP-1060 USER′S MANUAL
Page:7-7
Chapter
MP-1060 USER′S MANUAL
7 Languages
Page: 7-8
Chapter 7 Languages
MP-1060 USER′S MANUAL
Page:7-9
Chapter
MP-1060 USER′S MANUAL
7 Languages
Page: 7-10
Chapter 7 Languages
MP-1060 USER′S MANUAL
Page:7-11
Chapter
MP-1060 USER′S MANUAL
7 Languages
Page: 7-12
Chapter 7 Languages
MP-1060 USER′S MANUAL
Page:7-13
Chapter
7-4
7 Languages
Taiwanese Language Codes
MP-1060 USER′S MANUAL
Page: 7-14
Chapter 7 Languages
MP-1060 USER′S MANUAL
Page:7-15
Chapter
MP-1060 USER′S MANUAL
7 Languages
Page: 7-16
Chapter 7 Languages
MP-1060 USER′S MANUAL
Page:7-17
Chapter
MP-1060 USER′S MANUAL
7 Languages
Page: 7-18
Chapter 7 Languages
MP-1060 USER′S MANUAL
Page:7-19
Chapter
MP-1060 USER′S MANUAL
7 Languages
Page: 7-20
Chapter 7 Languages
MP-1060 USER′S MANUAL
Page:7-21
Chapter
MP-1060 USER′S MANUAL
7 Languages
Page: 7-22
Chapter 7 Languages
MP-1060 USER′S MANUAL
Page:7-23
Chapter
MP-1060 USER′S MANUAL
7 Languages
Page: 7-24
Chapter 7 Languages
MP-1060 USER′S MANUAL
Page:7-25
Chapter
MP-1060 USER′S MANUAL
7 Languages
Page: 7-26
Chapter 7 Languages
MP-1060 USER′S MANUAL
Page:7-27
Chapter
MP-1060 USER′S MANUAL
7 Languages
Page: 7-28
Chapter 7 Languages
7-5
Simplified Chinese Language Codes
MP-1060 USER′S MANUAL
Page:7-29
Chapter
MP-1060 USER′S MANUAL
7 Languages
Page: 7-30
Chapter 7 Languages
MP-1060 USER′S MANUAL
Page:7-31
Chapter
MP-1060 USER′S MANUAL
7 Languages
Page: 7-32
Chapter 7 Languages
MP-1060 USER′S MANUAL
Page:7-33
Chapter
MP-1060 USER′S MANUAL
7 Languages
Page: 7-34
Chapter 7 Languages
MP-1060 USER′S MANUAL
Page:7-35
Chapter
MP-1060 USER′S MANUAL
7 Languages
Page: 7-36
Chapter 7 Languages
MP-1060 USER′S MANUAL
Page:7-37
Chapter
MP-1060 USER′S MANUAL
7 Languages
Page: 7-38
Chapter 7 Languages
MP-1060 USER′S MANUAL
Page:7-39
Chapter
MP-1060 USER′S MANUAL
7 Languages
Page: 7-40
Chapter 7 Languages
7-6
Korean Language Codes
MP-1060 USER′S MANUAL
Page:7-41
Chapter
MP-1060 USER′S MANUAL
7 Languages
Page: 7-42
Chapter 7 Languages
MP-1060 USER′S MANUAL
Page:7-43
Chapter
MP-1060 USER′S MANUAL
7 Languages
Page: 7-44
Chapter 7 Languages
MP-1060 USER′S MANUAL
Page:7-45
Chapter
MP-1060 USER′S MANUAL
7 Languages
Page: 7-46
Download PDF
Similar pages