Savant Music Single Stream - Quick Reference Guide

For Product Info
Savant Music Single Stream - Quick Reference Guide
Box Contents
Rear Panel
(1) Savant Music Single Stream (SMS-100AM-xx)
(1) Installation Kit (075-0206-xx)
(1) 5V DC 3A Power Supply (025-0153-xx)
(includes interchangeable international adapters)
(1) Wall Bracket – Chassis Mount (074-0584-xx)
(1) Wall Bracket - Wall Mount (074-0585-xx)
(2) M3 x 6mm Flat-head Phillips Screw (039-0001-xx)
(1) Quick Reference Guide (this document)
Specifications
Environmental
Temperature
32° to 104° F (0° to 40°C)
Humidity
10% to 90% RH (non-condensing)
Cooling
10 CFM (Cubic Feet per Minute)
Max BTU
34.1 BTU/hr
A
Reset - Clears the network settings. Press and hold the Reset
button for five seconds until the Status LED blinks red rapidly;
then release. See Rapid Red Blink below.
B
Input power - Connect included power supply
Off: The processor is resetting, or system is
powered up and is currently booting the
embedded firmware.
Green: Connected/Communicating with the
Pro System Host.
Dimensions and Weight (Product)
Height
1.58 in (4.00 cm)
Width
7.86 in (20.00 cm)
Depth
7.65 in (19.40 cm)
Weight
Net: 1.3 lb (.59 kg) | Shipping: 2.1 lb (.95 kg)
Red: During the firmware update process, a
problem occurred and a reset will be initiated.
Orange: Firmware update is in process.
Power
Input Power
5V DC 3A
Max Power
15 Watts
Green Blinking: Was assigned an IP Address
and is communicating with the local network,
but not communicating with Pro System Host.
C
Audio
Digital to Analog
Conversion
Orange Blinking: A valid link-local IP Address
is established and SMS-100AM is trying to
connect with the Pro System Host.
24 bit / 96 kHz
Regulatory
Safety and
Emissions
FCC Part
15
RoHs
Compliant
CE
C-Tick
Red Blinking: Embedded firmware is running,
but SMS-100AM has not received an IP
Address.
ICES-003
Rapid Red Blink: The reset button was pressed
and held for five seconds and the SMS-100AM
is performing a factory reset.
Minimum Supported Release
Savant OS
da Vinci 8.6
D
Audio - Toslink (Optical) digital audio output port.
E
Ethernet - 8-pin RJ-45 female
Connects to a digital audio input on a switcher chassis for
streaming Savant Music. An adapter may be required to connect
to ports other than Toslink.
Network Requirements
Savant requires the use of business class/commercial grade network
equipment throughout the network to ensure the reliability of
communication between devices. These higher quality components also
allow for more accurate troubleshooting when needed.
When making connections, connect all Savant devices to the same local
area network (LAN) or subnet as the Host. Savant recommends not
implementing any type of traffic or packet shaping in your network
topology for the Savant devices as this may interfere with performance.
10/100/1000 Base-T auto negotiating
The SMS-100AM has a built-in single stream of Savant Music, which
includes popular music streaming services powered by Autonomic
MirageOS (Streaming service fees may apply).
To ensure that the IP Address will not change due to a power outage, a
static IP or DHCP reservation should be configured. Savant
recommends using DHCP reservation within the router. By using this
method, IP Addresses can be managed from a single UI avoiding the
need to access devices individually. Setting DHCP reservation varies
from router to router. Refer to the documentation for the router to
configure.
Network Changes
If the IP Address range in your network has changed, Savant
recommends the following steps to refresh any IP connection and
ensure the controller is communicating with the network correctly.
1.
Cycle Power
2.
Hot Plug Ethernet
(LAN) Connection
1.
2.
Disconnect the SMS-100AM from the AC
power source.
Wait 15 seconds and then reconnect.
Disconnect the Ethernet (LAN) connection
from the SMS-100AM.
Wait 15 seconds and then reconnect.
SMS-100AM-00 | 009-1581-01 | 171020
Copyright © 2017 Savant Systems, LLC
45 Perseverance Way, Hyannis, MA 02601
1
of
2
Savant.com | 508.683.2500
Installation
Audio and Ethernet Connections
The SMS-100AM can be mounted to a wall or similar, or can be installed
on a solid, flat, level surface such as a table, cabinet, or shelf. The
location should be dry, well ventilated, and out of direct sunlight.
Flat Surface Installation
When installing onto a flat surface such as a shelf, the wall bracket
should not be installed. This will allow for a flat, level installation.
Wall Bracket Installation
A two-piece wall mount bracket is included for installation to a wall or
similar. Wall mount instructions are provided below.
1
Attach the bracket that
mounts to the bottom of the
chassis using the included M3
x 6mm flat-head screws.
2
Attach the wall bracket
securely to the wall. If
mounting to drywall, a sturdy
anchor such as a threaded
drywall anchor should be used.
3
Position SMS-100AM over the
wall bracket and gently slide
into place. See image.
-
-
Connect a Cat 5e/6/7 Ethernet cable between SMS-100AM and the
local network router.
Connect a Digital Optical (Toslink) cable between the Audio output
port on the SMS-100AM and an audio input port on a Savant
SmartAudio chassis or amplifier. An adapter or convertor (not
included) may be required to connect to non-Toslink type input ports.
Connect the power cable to the 5V DC port and apply power to the
system. Savant recommends a pure sine wave uninterruptible power
supply when connecting to an AC power source. The SMS-100AM will
automatically obtain an IP Address through DHCP.
Regulatory
15.19. This device complies with part 15 of the FCC Rules. Operation is subject to the following two
conditions: (1) This device may not cause harmful interference, and (2) this device must accept any
interference received, including interferences that may cause undesired operation.
15.21. The changes or modifications not expressly approved by the party responsible for compliance could
void the user's authority to operate the equipment.
15.105. This equipment has been tested and found to comply with the limits for CLASS B digital device,
pursuant to Part 15 of FCC Rules. These limits are designed to provide reasonable protection against
harmful interference when the equipment is operated in a residential environment. This equipment
generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with
the instructions, may cause harmful interference to radio communications, However there is no guarantee
that interference will not occur in a particular installation, If this equipment does cause harmful interference
to radio or television reception, which can be determined by turning the equipment off and on, the user is
encouraged to try to correct the interference by one or more of the following measures:
Additional Documentation
Additional Documents are available on the Savant Customer
Community.
- Savant Music Server Deployment Guide (009-1473-xx)
- Reorient or relocate the receiving circuit different from that to which receiver is connected.
- Increase the separation between the equipment and the receiver.
- Consult the dealer or experienced radio/TV technician for help.
IC Regulations
RSS-Gen 7.1.3. This device complies with Industry Canada license-exempt RSS standard(s). Operation is
subject to the following two conditions: (1) This device may not cause interference, and (2) This device
must accept any interference, including interference that may cause undesired operation of the device.
RSS-21- Annexe 9: A 9.4. Le présent appareil est conforme aux CNR d'Industrie Canada applicables aux
appareils radio exempts de licence. L'exploitation est autorisée aux deux conditions suivantes: (1) l'appareil
ne doit pas produire de brouillage, et (2) l'utilisateur de l'appareil doit accepter tout brouillage
radioélectrique subi, même si le brouillage est susceptible d'en compromettre le fonctionnement.
Printed in China
Part # HDH6A008010
SMS-100AM-00 | 009-1581-01 | 171020
Copyright © 2017 Savant Systems, LLC
45 Perseverance Way, Hyannis, MA 02601
2
of
2
Savant.com | 508.683.2500
Download PDF
Similar pages