QuickSpecs
HP 7500 Switch Series
Overview
HP 7500 Switch Series
Product overview
The HP 7500 Switch Series comprises modular, multilayer chassis switches that meet the evolving needs of integrated services
networks. The switches can be deployed in multiple network environments, including the enterprise LAN core, aggregation layer,
and wiring closet edge. They offer 40GbE connectivity and cost-effective, wire-speed 10GbE ports to safeguard the throughput
and bandwidth needed for your mission-critical data and high-speed communications.
A passive backplane, support for load sharing, and redundant management and fabrics help the switch series provide high
availability. Moreover, these switches deliver wire-speed L2 and L3 routing services for the most demanding applications with
hardware-based IPv4 and IPv6 support.
HP 7502 Switch Chassis
Key features





Versatile, high-performance modular switches
Enterprise LAN core, aggregation, and edge
Extensive switching and routing, IPv6, and multiprotocol label switching (MPLS)
Advanced functionality with service modules
Robust network and service virtualization
Features and benefits
Quality of Service (QoS)



IEEE 802.1p prioritization
delivers data to devices based on the priority and type of traffic
Class of Service (CoS)
sets the IEEE 802.1p priority tag based on IP address, IP Type of Service (ToS), Layer 3 protocol, TCP/UDP port number,
source port, and DiffServ
Bandwidth shaping
o Port-based rate limiting
provides per-port ingress-/egress-enforced increased bandwidth
o Classifier-based rate limiting
c04111585 — DA – 13805 Worldwide — Version 35 — July 3, 2014
Page 1
QuickSpecs
HP 7500 Switch Series
Overview



uses an access control list (ACL) to enforce increased bandwidth
for ingress traffic on each port
o Reduced bandwidth
provides per-port, per-queue egress-based reduced bandwidth
Weighted random early detection (WRED)/random early detection (RED)
delivers congestion avoidance capabilities through the use of queue management algorithms
Powerful QoS feature
supports the following congestion actions: strict priority (SP) queuing, weighted round robin (WRR), weighted fair queuing
(WFQ), and WRED
Traffic policing
supports Committed Access Rate (CAR) and line rate
Intrusion detection/prevention system (IDS/IPS)





Deep packet inspection
module supports deep packet inspection and examines the packet payload as well as the frame and packet headers;
packets are dropped if attacks or intrusions are detected using signature-based or protocol anomaly-based detection
Signature-based detection
detects attacks that have known attack patterns; IPS maintains a signature database that contains the pattern definitions
for known attacks that can be updated automatically using a subscription service
Protocol anomaly-based detection
detects attacks that use anomalies in application protocol payloads
Severity-based action policies
involve action taken against attacks based on their severity; available actions are "allow," "block," and "terminate
connection" to provide appropriate mitigation
Signature update service
provides regular updates to the signature database, helping to ensure that the latest available signatures are installed
Virtual private network (VPN)



IPSec
provides secure tunneling over an untrusted network such as the Internet or a wireless network; offers data
confidentiality,
authenticity, and integrity between two network endpoints
Generic Routing Encapsulation (GRE)
transports Layer 2 connectivity over a Layer 3 path in a secured way; enables the segregation of traffic from site to site
Manual or automatic Internet Key Exchange (IKE)
provides both manual or automatic key exchange required for the algorithms used in encryption or authentication; autoIKE allows automated management of the public key exchange, providing the highest levels of encryption
Management





Management interface control
provides management access through a modem port and terminal interface, as well as in-band and out-of-band Ethernet
ports; provides access through terminal interface, telnet, or secure shell (SSH)
Industry-standard CLI with a hierarchical structure
reduces training time and expenses, and increases productivity in multivendor installations
Management security
restricts access to critical configuration commands; offers multiple privilege levels with password protection; ACLs
provide telnet and SNMP access; local and remote syslog capabilities allow logging of all access
SNMPv1, v2, and v3
provide complete support of SNMP; provide full support of industry-standard Management Information Base (MIB) plus
private extensions; SNMPv3 supports increased security using encryption
sFlow (RFC 3176)
c04111585 — DA – 13805 Worldwide — Version 35 — July 3, 2014
Page 2
QuickSpecs
HP 7500 Switch Series
Overview









provides scalable ASIC-based wirespeed network monitoring and accounting with no impact on network performance;
this allows network operators to gather a variety of sophisticated network statistics and information for capacity
planning and real-time network monitoring purposes
Remote monitoring (RMON)
uses standard SNMP to monitor essential network functions; supports events, alarm, history, and statistics group plus a
private alarm extension group
FTP, TFTP, and SFTP support
offers different mechanisms for configuration updates; FTP allows bidirectional transfers over a TCP/IP network; trivial
FTP (TFTP) is a simpler method using User Datagram Protocol (UDP); Secure File Transfer Protocol (SFTP) runs over an
SSH tunnel to provide additional security
Debug and sampler utility
supports ping and traceroute for both IPv4 and IPv6
Network Time Protocol (NTP)
synchronizes timekeeping among distributed time servers and clients; keeps timekeeping consistent among all clockdependent devices within the network so that the devices can provide diverse applications based on the consistent time
Network Quality Analyzer (NQA)
analyzes network performance and service quality by sending test packets, and provides network performance and
service quality parameters such as jitter, TCP, or FTP connection delays and file transfer rates; allows a network manager
to determine overall network performance and to diagnose and locate network congestion points or failures
Information center
provides a central repository for system and network information; aggregates all logs, traps, and debugging information
generated by the system and maintains them in order of severity; outputs the network information to multiple channels
based on user-defined rules
IEEE 802.1AB Link Layer Discovery Protocol (LLDP)
advertises and receives management information from adjacent devices on a network, facilitating easy mapping by
network management applications
Dual flash images
provides independent primary and secondary operating system files for backup while upgrading
Multiple configuration files
stores easily to the flash image
Connectivity








High-density port connectivity
Provides up to 10 interface module slots and up to 40 40GbE ports, 84 10GbE ports, 480 Fiber Gigabit ports, or 480 PoEenabled ports per HP 7500 Switch Series system
Jumbo frames
Allow high-performance remote backup and disaster-recovery systems with up to 9,216 bytes
Loopback
supports internal loopback testing for maintenance purposes and an increase in availability; loopback detection protects
against incorrect cabling or network configurations and can be enabled on a per-port or per-VLAN basis for added
flexibility
Ethernet operations, administration and maintenance (OAM)
detects data link layer problems that occurred in the "last mile" using the IEEE 802.3ah OAM standard; monitors the
status of the link between two devices
Flexible port selection
Includes 100/1000BASE-X auto speed selection, 10/100/1000BASE-T auto speed detection, as well as auto duplex and
MDI/MDI-X
Monitor link
collects statistics on performance and errors on physical links, increasing system availability
IEEE 802.3af Power over Ethernet (PoE)
provides up to 15.4 W per port to IEEE 802.3af-compliant PoE-powered devices such as IP phones, wireless access points,
and security cameras
Dual-personality functionality
c04111585 — DA – 13805 Worldwide — Version 35 — July 3, 2014
Page 3
QuickSpecs
HP 7500 Switch Series
Overview



includes four 10/100/1000 ports or SFP slots for optional fiber connectivity such as Gigabit-SX, -LX, and -LH, or 100-FX
Packet storm protection
protects against unknown broadcast, unknown multicast, or unicast storms with user-defined thresholds
Flow control
provides back pressure using standard IEEE 802.3x, reducing congestion in heavy traffic situations
IEEE 802.3at Power over Ethernet (PoE+) support
provides up to 30 watts of power at the power sourcing equipment (PSE)
Performance



High-speed fully distributed architecture
Supports a maximum of 1,152 Gb/s switching capacity with a 2.4 Tb/s backplane, providing enhanced performance and
future expansion capability; delivers up to 714 Mp/s throughput with dual fabrics; performs all switching and routing
functions in the I/O modules; and meets the current and future demand of an enterprise's bandwidth-intensive
applications
Scalable system design
Provides investment protection to support future technologies and higher-speed connectivity with a backplane designed
to accommodate bandwidth increases
Flexible chassis selection
Enables you to tailor your product selections to your budget with a choice of six chassis, ranging from a 10-slot to a 2-slot
chassis
Resiliency and high availability












Redundant/load-sharing fabrics, management, fan assemblies, and power supplies
increase total performance and power availability while providing hitless, stateful failover
All hot-swappable modules
Allows replacement of modules without any impact on other modules
Dual internal power supply
provides high reliability
Separate data and control paths
separates control from services and keeps service processing isolated; increases security and performance
Passive design system
delivers increased system reliability as the backplane has no active components
IEEE 802.3ad link-aggregation control protocol (LACP)
Supports up to 128 trunks, each with 8 links per trunk; and provides support for static or dynamic groups and a userselectable hashing algorithm
Intelligent Resilient Framework (IRF)
creates virtual resilient switching fabrics, where two or more switches perform as a single L2 switch and L3 router;
switches do not have to be co-located and can be part of a disaster-recovery system; servers or switches can be attached
using standard LACP for automatic load balancing and high availability; can eliminate the need for complex protocols like
Spanning Tree Protocol, Equal-Cost Multipath (ECMP), or VRRP, thereby simplifying network operation
IRF capability
provides single IP address management for a resilient virtual switching fabric of up to four switches
Ring resiliency protection protocol (RRPP)
Provides standard sub-100 ms recovery for a ring Ethernet-based topology
Virtual Router Redundancy Protocol (VRRP)
allows a group of routers to dynamically back each other up to create highly available routed environments
Hitless patch upgrades
allows patches and new service features to be installed without restarting the equipment, increasing network uptime and
facilitating maintenance
Graceful restart
supports graceful restart for OSPF, IS-IS, BGP, LDP, and RSVP; the network remains stable during the active-standby
switchover; after the switchover, the device quickly learns the network routes by communicating with adjacent routers;
c04111585 — DA – 13805 Worldwide — Version 35 — July 3, 2014
Page 4
QuickSpecs
HP 7500 Switch Series
Overview



forwarding remains uninterrupted during the switchover to achieve nonstop forwarding (NSF)
Ultrafast protocol convergence with standards-based failure detection—bidirectional
Enables link connectivity monitoring and reduces network convergence time for the routing information protocol (RIP),
OSPF, BGP, IS-IS, VRRP, MPLS, and IRF
Smart link
allows 50 ms failover between links
IP/LDP FRR
nodes are configured with backup ports, routes, and LSPs; local implementation requires no cooperation of adjacent
devices, simplifying the deployment; solves the traditional convergence faults in IP forwarding and MPLS forwarding,
protecting the links, nodes, and paths without establishing respective backup LSPs for them; realizes restoration within
50 ms, with the restoration time independent of the number of routes and fast link switchovers, without route
convergence
Layer 2 switching











VLAN
Supports up to 4,096 port-based or IEEE 802.1Q-based VLANs; and supports MAC-based VLANs, protocol-based VLANs,
and
IP-subnet-based VLANs for added flexibility
Port isolation
increases security by isolating ports within a VLAN while still allowing them to communicate with other VLANs
Bridge Protocol Data Unit (BPDU) tunneling
transmits Spanning Tree Protocol BPDUs transparently, allowing correct tree calculations across service providers, WANs,
or MANs
GARP VLAN Registration Protocol
allows automatic learning and dynamic assignment of VLANs
Port mirroring
Duplicates port traffic (ingress and egress) to a local or remote monitoring port; and supports four mirroring groups, with
an unlimited number of ports per group
Spanning Tree Protocol (STP)
supports standard IEEE 802.1D STP, IEEE 802.1w Rapid Spanning Tree Protocol (RSTP) for faster convergence, and IEEE
802.1s Multiple Spanning Tree Protocol (MSTP)
Internet Group Management Protocol (IGMP) and Multicast Listener Discovery (MLD) protocol snooping
controls and manages the flooding of multicast packets in a Layer 2 network
Device Link Detection Protocol (DLDP)
monitors link connectivity and shuts down ports at both ends if unidirectional traffic is detected, preventing loops in STPbased networks
IEEE 802.1ad QinQ and selective QinQ
increase the scalability of an Ethernet network by providing a hierarchical structure; connect multiple LANs on a highspeed campus or metro network
Super VLAN
Saves IP address space, using RFC 3069 standard (also called VLAN aggregation)
Per-VLAN Spanning Tree Plus (PVST+)
allows each VLAN to build a separate spanning tree to improve link bandwidth usage in network environments with
multiple VLANs
Layer 3 services


Address Resolution Protocol (ARP)
determines the MAC address of another IP host in the same subnet; supports static ARPs; gratuitous ARP allows detection
of duplicate IP addresses; proxy ARP allows normal ARP operation between subnets or when subnets are separated by a
Layer 2 etwork
User Datagram Protocol (UDP) helper
redirects UDP broadcasts to specific IP subnets to prevent server spoofing
c04111585 — DA – 13805 Worldwide — Version 35 — July 3, 2014
Page 5
QuickSpecs
HP 7500 Switch Series
Overview


Dynamic Host Configuration Protocol (DHCP)
simplifies the management of large IP networks and supports client and server; DHCP Relay enables DHCP operation
across subnets
Domain Name System (DNS)
provides a distributed database that translates domain names and IP addresses, which simplifies network design;
supports client and server
Layer 3 routing

















Static IPv4 routing
provides simple manually configured IPv4 routing
Routing Information Protocol (RIP)
uses a distance vector algorithm with UDP packets for route determination; supports RIPv1 and RIPv2 routing; includes
loop protection
Open shortest path first (OSPF)
delivers faster convergence; uses this link-state routing Interior Gateway Protocol (IGP), which supports ECMP, NSSA, and
MD5 authentication for increased security and graceful restart for faster failure recovery
Intermediate system to intermediate system (IS-IS)
uses a path vector Interior Gateway Protocol (IGP), which is defined by the ISO organization for IS-IS routing and extended
by IETF RFC 1195 to operate in both TCP/IP and the OSI reference model (Integrated IS-IS)
Border Gateway Protocol 4 (BGP-4)
delivers an implementation of the Exterior Gateway Protocol (EGP) utilizing path vectors; uses TCP for enhanced
reliability for the route discovery process; reduces bandwidth consumption by advertising only incremental updates;
supports extensive policies for increased flexibility; scales to very large networks
Policy-based routing
makes routing decisions based on policies set by the network administrator
IP performance optimization
Provides a set of tools to improve the performance of IPv4 networks; and includes directed broadcasts, customization of
TCP parameters, support of ICNP error packets, and extensive display capabilities
Unicast Reverse Path Forwarding (uRPF)
limits erroneous or malicious traffic in accordance with RFC 3074
Static IPv6 routing
provides simple manually configured IPv6 routing
Dual IP stack
maintains separate stacks for IPv4 and IPv6 to ease the transition from an IPv4-only network to an IPv6-only network
design
Routing Information Protocol next generation (RIPng)
extends RIPv2 to support IPv6 addressing
OSPFv3
provides OSPF support for IPv6
IS-IS for IPv6
extends IS-IS to support IPv6 addressing
BGP+
extends BGP-4 to support Multiprotocol BGP (MBGP), including support for IPv6 addressing
IPv6 tunneling
allows IPv6 packets to traverse IPv4-only networks by encapsulating the IPv6 packet into a standard IPv4 packet;
supports manually configured, 6to4, and Intra-Site Automatic Tunnel Addressing Protocol (ISATAP) tunnels; is an
important element for the transition from IPv4 to IPv6
Multiprotocol Label Switching (MPLS)
uses BGP to advertise routes across Label Switched Paths (LSPs), but uses simple labels to forward packets from any
Layer 2 or Layer 3 protocol, which reduces complexity and increases performance; supports graceful restart for reduced
failure impact; supports LSP tunneling and multilevel stacks
Multiprotocol Label Switching (MPLS) Layer 3 VPN
allows Layer 3 VPNs across a provider network; uses MP-BGP to establish private routes for increased security; supports
c04111585 — DA – 13805 Worldwide — Version 35 — July 3, 2014
Page 6
QuickSpecs
HP 7500 Switch Series
Overview



RFC 2547bis multiple autonomous system VPNs for added flexibility
Multiprotocol Label Switching (MPLS) Layer 2 VPN
establishes simple Layer 2 point-to-point VPNs across a provider network using only MPLS Label Distribution Protocol
(LDP); requires no routing and therefore decreases complexity, increases performance, and allows VPNs of non-routable
protocols; uses no routing information for increased security; supports Circuit Cross Connect (CCC), Static Virtual Circuits
(SVCs), Martini draft, and Kompella-draft technologies
Virtual Private LAN Service (VPLS)
establishes point-to-multipoint Layer 2 VPNs across a provider network
Service loopback
allows any module to take advantage of higher-featured modules, including OAA modules, by redirecting traffic; reduces
investment and enables higher bandwidth and load sharing; supports IPv6, IPv6
multicast, tunneling, and MPLS
Security













Access control list (ACL)
supports powerful ACLs for both IPv4 and IPv6; ACLs are used for filtering traffic to prevent unauthorized users from
accessing the network, or for controlling network traffic to save resources; rules can either deny or permit traffic to be
forwarded; rules can be based on a Layer 2 header or a Layer 3 protocol header; rules can be set to operate on specific
dates or times
Remote Authentication Dial-In User Service (RADIUS)
eases switch security access administration by using a password authentication server
Terminal Access Controller Access-Control System (TACACS+)
delivers an authentication tool using TCP with encryption of the full authentication request, providing additional security
Switch management logon security
helps secure switch CLI logon by optionally requiring either RADIUS or TACACS+ authentication
Secure shell (SSHv2)
uses external servers to securely log in to a remote device; with authentication and encryption, it protects against IP
spoofing and plain-text password interception; increases the security of Secure FTP (SFTP) transfers
DHCP snooping
enables DHCP clients to receive IP addresses from authorized DHCP servers and maintains a list of DHCP entries for
trusted ports; prevents users from receiving fake IP addresses and reduces ARP attacks, improving security
IP source guard
filters packets on a per-port basis to prevent illegal packets from being forwarded
ARP attack protection
protects from attacks using a large number of ARP requests with a host-specific, user-selectable threshold
Port security
allows access only to specified MAC addresses, which can be learned or specified by the administrator
IEEE 802.1X support
provides port-based user authentication with support for Extensible Authentication Protocol (EAP) MD5, TLS, TTLS, and
PEAP with choice of AES, TKIP, and static or dynamic WEP encryption for protecting wireless traffic between
authenticated clients and the access point
Media access control (MAC) authentication
provides simple authentication based on a user's MAC address; supports local or RADIUS-based authentication
Multiple user authentication methods
o IEEE 802.1X
uses an IEEE 802.1X supplicant on the client in conjunction with a RADIUS server to authenticate in accordance
with industry standards
o Web-based authentication
provides a browser-based environment, similar to IEEE 802.1X, to authenticate clients that do not support the
IEEE 802.1X supplicant
o MAC-based authentication
authenticates the client with the RADIUS server based on the client's MAC address
DHCP protection
c04111585 — DA – 13805 Worldwide — Version 35 — July 3, 2014
Page 7
QuickSpecs
HP 7500 Switch Series
Overview


blocks DHCP packets from unauthorized DHCP servers, preventing denial-of-service attacks
Endpoint Admission Defense (EAD)
provides security policies to users accessing a network
Port isolation
secures and adds privacy, and prevents malicious attackers from obtaining user information
Convergence








LLDP-MED (Media Endpoint Discovery)
defines a standard extension of LLDP that stores values for parameters such as QoS and VLAN to automatically configure
network devices such as IP phones
Multicast Source Discovery Protocol (MSDP)
allows multiple PIM-SM domains to interoperate; is used for inter-domain multicast applications
Internet Group Management Protocol (IGMP)
utilizes Any-Source Multicast (ASM) or Source-Specific Multicast (SSM) to manage IPv4 multicast networks; supports
IGMPv1, v2, and v3
Protocol Independent Multicast (PIM)
defines modes of Internet IPv4 and IPv6 multicasting to allow one-to-many and many-to-many transmission of
information; supports PIM Dense Mode (DM), Sparse Mode (SM), and Source-Specific Mode (SSM)
Multicast Border Gateway Protocol (MBGP)
allows multicast traffic to be forwarded across BGP networks and kept separate from unicast traffic
Multicast Listener Discovery (MLD) protocol
establishes, maintains, and manages IPv6 multicast groups and networks; supports v1 and v2 and utilizes Any-Source
Multicast (ASM) or Source-Specific Multicast (SSM)
Multicast VLAN
allows multiple VLANs to receive the same IPv4 or IPv6 multicast traffic, lessening network bandwidth demand by
reducing or eliminating multiple streams to each VLAN
Voice VLAN
automatically assigns VLAN and priority for IP phones, simplifying network configuration and maintenance
Integration





Open Application Architecture (OAA)
provides high-performance application-specific modules fully integrated with the switching architecture; uses the chassis
high-speed backplane to access network-related data; increases performance, reduces costs, and simplifies network
management
Local and global server load-balancing module
Improves traffic distribution using powerful scheduling algorithms, including L4 to L7 services; and monitors the health
status of servers and firewalls
NetStream module
Provides traffic analysis and statistics capture to allow network administrators to rapidly identify network anomalies and
security threats as well as obtain capacity planning information; and supports NetFlow v5 and v9
Unified wired-WLAN module
Supports up to 1,024 access points per module; can be used with select HP access points (refer to the HP 10500/7500
20G Unified Wired-WLAN Module data sheet for more details); provides N+1, N+N, and 1+1 redundancy with sub-second
failovers; offers IPv4/IPv6 and end-to-end QoS; and includes flexible forwarding modes as well as Wi-Fi clear connect
radio-frequency optimization and integrated IDS
VPN 20 Gb/s firewall module
Provides enhanced stateful packet inspection and filtering; supports flexible security zones and virtual firewall
containment; offers advanced VPN services with 3DES and AES encryption at high performance and low latency;
facilitates Web content filtering; and enables application prioritization and optimization
Additional information
c04111585 — DA – 13805 Worldwide — Version 35 — July 3, 2014
Page 8
QuickSpecs
HP 7500 Switch Series
Overview




Green initiative support
provides support for RoHS and WEEE regulations
Low power-consumption switch
Is rated among the switches with the lowest power consumption in the industry by Miercom independent tests
Unified HP Comware operating system with modular architecture
Unified HP Comware operating system with modular architecture provides an easy-to-enhance-and-extend feature set,
which doesn't require whole-scale changes; all switching, routing, and security platforms leverage the Comware OS, a
common unified modular operating system
OPEX savings
simplifies and streamlines deployment, management, and training through the use of a common operating system,
thereby cutting costs as well as reducing the risk of human errors associated with having to manage multiple operating
systems across different platforms and network layers
Warranty and support



1-year Warranty 2.0
advance hardware replacement with 10-calendar-day delivery (available in most countries)
Electronic and telephone support (for Warranty 2.0)
limited electronic and 24x7 telephone support is available from HP for the entire warranty period; to reach our support
centers, refer to www.hp.com/networking/contact-support; for details on the duration of support provided with your
product purchase, refer to www.hp.com/networking/warrantysummary
Software releases
to find software for your product, refer to www.hp.com/networking/support; for details on the software releases
available with your product purchase, refer to www.hp.com/networking/warrantysummary
c04111585 — DA – 13805 Worldwide — Version 35 — July 3, 2014
Page 9
QuickSpecs
HP 7500 Switch Series
Configuration
Build To Order: BTO is a standalone unit with no integration. BTO products ship standalone are not part of a CTO or RackShippable solution.
HP 7502 Switch Chassis
 Must select min 1 Power Supply
 Must select Min 1 Fabric Module
 4U - Height
JD242B
HP 7503 Switch Chassis
 Must select min 1 Power Supply
 Must select Min 1 Fabric Module
 10U - Height
JD240B
HP 7503-S Switch Chassis w/1 Fabric Slot
 Must select min 1 Power Supply
 Must select Min 1 Fabric Module
 4U - Height
JD243B
HP 7503 Swch w/48p GT 2p 10G 384Gbps MPU
 Must select min 1 Power Supply
 1 - JD193B - HP 384 Gbps A7500 Fab Mod w/2 XFP Ports included min=0 \ max=2 XFP Transceivers
 1 - JD229B - HP 48p Gig-T PoE+ Ext A7500 Module included
 4U - Height
JG507A
HP 7506 Switch Chassis
 Must select min 1 Power Supply
 Must select Min 1 Fabric Module
 13U - Height
JD239B
HP 7506 Swch w/96p GT 2p 10G 384Gbps MPU
 Must select min 1 Power Supply
 1 - JD193B - HP 384 Gbps A7500 Fab Mod w/2 XFP Ports included min=0 \ max=2 XFP Transceivers
 1 - JD229B - HP 48p Gig-T PoE+ Ext A7500 Module included
 13U - Height
JG508A
HP 7506-V Switch Chassis
 Must select min 1 Power Supply
 Must select Min 1 Fabric Module
 21U - Height
JD241B
HP 7510 Switch Chassis
 Must select min 1 Power Supply
JD238B
c04111585 — DA – 13805 Worldwide — Version 35 — July 3, 2014
Page 10
QuickSpecs
HP 7500 Switch Series
Configuration


Must select Min 1 Fabric Module
16U - Height
HP 7510 Swch w/96p GT 768Gbps MPU
 Must select min 1 Power Supply
 1 - JD220A - HP 384 Gbps A7500 Fab Mod w/2 XFP Ports included min=0 \ max=2 XFP Transceivers
 1 - JD229B - HP 48p Gig-T PoE+ Ext A7500 Module included
 16U - Height
Remarks
JG509A
BTO Model 1s should never receive an 0D1 and therefore cannot be factory integrated into a
rack.
Box Level Integration CTO Models
HP 75xx CTO Switch Solution
 SSP trigger sku
JG707A
HP 7502 Switch Chassis CTO
 Must select min 1 Power Supply
 Must select Min 1 Fabric Module
 4U - Height
JD242B
See Configuration Note: 2,3
HP 7503 Switch Chassis - CTO
 Must select min 1 Power Supply
 Must select Min 1 Fabric Module
 10U - Height
JD240B
See Configuration Note: 3,4
HP 7503 Switch Chassis with 1 Fabric Slot - CTO
 Must select min 1 Power Supply
 Must select Min 1 Fabric Module
 4U - Height
JD243B
See Configuration Note: 2,3
HP 7506 Switch Chassis - CTO
 Must select min 1 Power Supply
 Must select Min 1 Fabric Module
 13U - Height
JD239B
See Configuration Note: 3,4
HP 7506 Vertical Switch Chassis - CTO
 Must select min 1 Power Supply
 Must select Min 1 Fabric Module
 21U - Height
JD241B
See Configuration Note: 3,4
c04111585 — DA – 13805 Worldwide — Version 35 — July 3, 2014
Page 11
QuickSpecs
HP 7500 Switch Series
Configuration
HP 7510 Switch Chassis - CTO
 Must select min 1 Power Supply
 Must select Min 1 Fabric Module
 16U - Height
JD238B
See Configuration Note: 3,4
Configuration Rules:
Note 2
If this Switch is selected at least one of these Power Supply with is required: (Use #0D1 if switch is CTO)
HP 7502 300W AC Power Supply
JD226A
HP 7500 650W DC Power Supply
JD209A
HP 7500 650W AC Power Supply
JD217A
Note 3
If the Switch Chassis is to be Box Level Factory Integrated (CTO), Then the #0D1 is required on the Switch Chassis
and integrated to the JG707A - HP 7500 CTO Enablement. (Min 1/Max 1 Switch per SSP)
Note 4
If this Switch is selected at least one of these Power Supplies is required: (Use #0D1 if switch is CTO)
HP 7500 1400W DC Power Supply
JD208A
HP 7500 1400W AC Power Supply
JD218A
HP 7500 2800W AC Power Supply
JD219A
HP 7500 6000W AC Power Supply
JD227A
Rack Level Integration CTO Models
HP 7502 Switch Chassis
 Must select min 1 Power Supply
 Must select Min 1 Fabric Module
 4U - Height
JD242B
See Configuration Note: 1, 3
HP 7503 Switch Chassis
 Must select min 1 Power Supply
 Must select Min 1 Fabric Module
 10U - Height
JD240B
See Configuration Note: 3,4
HP 7503-S Switch Chassis w/1 Fabric Slot
 Must select min 1 Power Supply
 Must select Min 1 Fabric Module
 4U - Height
JD243B
See Configuration Note: 1, 3
HP 7506 Switch Chassis
 Must select min 1 Power Supply
 Must select Min 1 Fabric Module
 13U - Height
JD239B
See Configuration Note: 3,4
c04111585 — DA – 13805 Worldwide — Version 35 — July 3, 2014
Page 12
QuickSpecs
HP 7500 Switch Series
Configuration
HP 7506-V Switch Chassis
 Must select min 1 Power Supply
 Must select Min 1 Fabric Module
 21U - Height
JD241B
See Configuration Note: 3,4
HP 7510 Switch Chassis
 Must select min 1 Power Supply
 Must select Min 1 Fabric Module
 16U - Height
JD238B
See Configuration Note: 3,4
Configuration rules:
Note 1
If this Switch is selected at least one of these Power Supply with is required: (Use #0D1 if switch is CTO)
HP 7502 300W AC Power Supply
JD226A
HP 7500 650W DC Power Supply
JD209A
HP 7500 650W AC Power Supply
JD217A
Note 3
If HP CTO Switch Chassis is selected to be Rack Level Integration, Then the CTO Switch Chassis needs to integrate
(with #0D1) to the BW966A and BW968A HP Universal Rack Only. (Default to the BW966A.)
Note 4
If this Switch is selected at least one of these Power Supplies is required: (Use #0D1 if switch is CTO)
HP 7500 1400W DC Power Supply
JD208A
HP 7500 1400W AC Power Supply
JD218A
HP 7500 2800W AC Power Supply
JD219A
HP 7500 6000W AC Power Supply
JD227A
Enter the following menu selections as integrated to the CTO Model X server above if order is factory built.
Internal Power Supplies
System (std 0 // max 2) User Selection (min 1 // max 2)
See Configuration
Note:3
HP 7502 300W AC Power Supply
 includes 1 x c13, 300w
JD226A
See Configuration
Note: 1,4
PDU Cable NA/MEX/TW/JP
 C15 PDU Jumper Cord (NA/MEX/TW/JP)
#B2B
PDU Cable ROW
 C15 PDU Jumper Cord (ROW)
#B2C
HP 7500 650W DC Power Supply
JD209A
c04111585 — DA – 13805 Worldwide — Version 35 — July 3, 2014
Page 13
QuickSpecs
HP 7500 Switch Series
Configuration
See Configuration
Note: 1
HP 7500 650W AC Power Supply
 includes 1 x c13, 650w
JD217A
See Configuration
Note: 1,4,5
PDU Cable NA/MEX/TW/JP
 C15 PDU Jumper Cord (NA/MEX/TW/JP)
#B2B
PDU Cable ROW
 C15 PDU Jumper Cord (ROW)
#B2C
HP 7500 1400W DC Power Supply
JD208A
See Configuration
Note: 2
HP 7500 1400W AC Power Supply
 includes 1 x c19, 1400w
JD218A
See Configuration
Note: 2,4
PDU Cable NA/MEX/TW/JP
 C15 C19 PDU Jumper Cord (NA/MEX/TW/JP)
JD218A#B2B
PDU Cable ROW
 C19 PDU Jumper Cord (ROW)
JD218A#B2C
High Volt Switch to Wall Power Cord
 NEMA L6-20P Cord (NA/MEX/JP/TW)
JD218A#B2E
HP 7500 2800W AC Power Supply
 includes 2 x c19, 2800w
JD219A
See Configuration
Note: 2,4,6
High Volt Switch to Wall Power Cord
 NEMA L6-20P Cord (NA/MEX/JP/TW)
HP 7500 6000W AC Power Supply
 includes 4 x c19, 6000w
#B2E
JD227A
See Configuration
Note: 2,4,6
PDU Cable NA/MEX/TW/JP
JD227A#B2B
c04111585 — DA – 13805 Worldwide — Version 35 — July 3, 2014
Page 14
QuickSpecs
HP 7500 Switch Series
Configuration

C15 C19 PDU Jumper Cord (NA/MEX/TW/JP)
High Volt Switch to Wall Power Cord
 NEMA L6-20P Cord (NA/MEX/JP/TW)
JD227A#B2E
High Volt Switch to Wall Power Cord
 NEMA L6-20P Cord (NA/MEX/JP/TW)
#B2E
Configuration Rules:
Note 1
Only supported on the JD242x and JD243x.
Note 2
Only supported on the JD238x,JD239x,JD241x, JD240x, JG507A, JG508A, and JG509A.
Note 3
If 2 power supplies are selected they must be the same Sku number.
Note 4
Localization required on orders without #B2B, #B2C, #B2D or #B2E options.
Note 5
If CTO Switch Chassis is ordered #0D1 (Rack Integrated), Then #B2B, or #B2C is
Required on the Power Supply's. (Optional when Switch is not Factory Racked. See Drop
down remark in Power Supplies section.)
Note 6
If the CTO Switch Chassis is ordered #0D1 (Rack Integrated), Then #B2D is Required on
the Power Supply's. (Optional when Switch is not Factory Racked. See Drop down
remark in Power Supplies section.)
Remarks:
Drop down under power supply should offer the following options and results:
Switch to PDU Power Cord - #B2B in North America, Mexico, Taiwan, and Japan or #B2C
ROW. (Watson Default B2B or B2C for Rack Level CTO)
Switch to Wall Power Cord - Localized Option (Watson Default for BTO and Box Level
CTO)
High Volt Power Electrical Module to Wall Power Cord - #B2E Option. (Offered only in
North America, Mexico, Taiwan, and Japan)
Modules
Ethernet Modules
(Switch JD243x and JD242x ) System (std 0 // max 2) User Selection (min 0 // max 2) per enclosure
(Switch JG507A) System (std 1 // max 2) User Selection (min 0 // max 1) per enclosure
(Switch JD240x) System (std 0 // max 3) User Selection (min 0 // max 3) per enclosure
(Switch JD239x and JD241x ) System (std 0 // max 6) User Selection (min 0 // max 6) per enclosure
c04111585 — DA – 13805 Worldwide — Version 35 — July 3, 2014
Page 15
QuickSpecs
HP 7500 Switch Series
Configuration
(Switch JG508A) System (std 2 // max 6) User Selection (min 0 // max 4) per enclosure
(Switch JD238x) System (std 0 // max 10) User Selection (min 0 // max 10) per enclosure
(Switch JG509A) System (std 2 // max 10) User Selection (min 0 // max 8) per enclosure
HP 7500 24-port GbE SFP Module
 min=0 \ max=24 SFP Transceivers
JD203B
See Configuration
Note:1
HP 7500 12-port GbE SFP Module
 min=0 \ max=12 SFP Transceivers
JD207A
See Configuration
Note:1
HP 7500 48-port GbE SFP Enhanced Module
 min=0 \ max=48 SFP Transceivers
JD221A
See Configuration
Note:1
HP 7500 24p GbE SFP Mod w/8 Combo Ports
 min=0 \ max=24 SFP Transceivers
JD223A
See Configuration
Note:1
HP 7500 40p Gig-T/8p SFP PoE-ready Mod
 min=0 \ max= 8 SFP Transceivers
JD228B
See Configuration
Note:1, 8, 14
HP 7500 24-port GbE SFP Enhanced Module
 min=0 \ max=24 SFP Transceivers
JD231A
See Configuration
Note:1
HP 7500 24-port GbE SFP Extended Module
 min=0 \ max=24 SFP Transceivers
JD234A
See Configuration
Note:1
HP 7500 48-port GbE SFP Extended Module
 min=0 \ max=48 SFP Transceivers
JD237A
See Configuration
Note:1
HP 7500 48-port GbE SFP Module
 min=0 \ max=48 SFP Transceivers
JD211B
See Configuration
Note:1
HP 7500 24-port GbE SFP SC TAA Module
 min=0 \ max=24 SFP Transceivers
JC704A
See Configuration
Note:1, 9
HP A7500 40p Gig-T/8p SFP PoE SC TAA Mod
c04111585 — DA – 13805 Worldwide — Version 35 — July 3, 2014
JC710A
Page 16
QuickSpecs
HP 7500 Switch Series
Configuration

min=0 \ max= 8 SFP Transceivers
See Configuration
Note:1, 8, 9, 14
HP A7500 16p GbE SFP/8p Combo EB TAA Mod
 min=0 \ max=24 SFP Transceivers
JC715A
See Configuration
Note:1, 9
HP A7500 16p GbE SFP/8p Combo SD TAA Mod
 min=0 \ max=24 SFP Transceivers
JC718A
See Configuration
Note:1, 9
HP 7500 48-port GbE SFP SD TAA Module
 min=0 \ max=48 SFP Transceivers
JC721A
See Configuration
Note:1, 9
HP A7500 20p Gig-T/4p Cmb PoE-upg SC Mod
 min=0 \ max= 4 SFP Transceivers
JC669A
See Configuration
Note:1, 12
HP 7500 48-port 100BASE-FX Module
 min=0 \ max=48 SFP 100 Transceivers
JD197B
See Configuration
Note:2, 7
HP 7500 8-port 10G SFP+ Module
 min=0 \ max=8 per SFP+ Transceivers
JF290A
See Configuration
Note:3
HP 7500 8-port 10GbE SFP+ SC TAA Module
 min=0 \ max=8 per SFP+ Transceivers
JC723A
See Configuration
Note:3, 9
HP 7500 4-port 10GbE XFP Enhanced Module
 min=0 \ max=4 XFP
JD232A
See Configuration
Note:4
HP 7500 2-port 10GbE XFP Enhanced Module
 min=0 \ max=2 XFP
JD233A
See Configuration
Note:4
HP 7500 8-port 10GbE XFP Extended Module
 min=0 \ max=8 XFP Transceivers
JD191A
See Configuration
Note:4
HP 7500 2-port 10GbE XFP Module
 min=0 \ max=2 XFP Transceivers
JD201A
See Configuration
Note:4
c04111585 — DA – 13805 Worldwide — Version 35 — July 3, 2014
Page 17
QuickSpecs
HP 7500 Switch Series
Configuration
HP 7500 24p Gig-T / 2p 10GbE XFP Mod
 min=0 \ max=2 XFP Transceivers
JD206A
See Configuration
Note:4
HP 7500 4-port 10GbE XFP Extended Module
 min=0 \ max=4 XFP Transceivers
JD235A
See Configuration
Note:4
HP 7500 2-port 10GbE XFP Extended Module
 min=0 \ max=2 XFP Transceivers
JD236A
See Configuration
Note:4
HP 7500 24p GbE SFP / 2p 10GbE XFP Mod
 min=0 \ max=2 XFP min=0 \ max=24 SFP Transceivers
JD205A
See Configuration
Note:5
HP 7500 24p GbE-SFP/2p 10GbE XFP Ext Mod
 min=0 \ max=2 XFP min=0 \ max=24 SFP Transceivers
JD230A
See Configuration
Note:5
HP 7500 24-port Gig-T Module
 No supported Transceivers
JD204B
HP 7500 48-port Gig-T Module
 No supported Transceivers
JD210A
See Configuration
Note:8,14
HP 7500 48p Gig-T PoE+ Extended Module
 Includes DIMM
JD229B
HP 7500 48p 1000BASE-T PoE+ SC Mod
 No supported Transceivers
JG663A
HP 7500 48p 1000BASE-T PoE+ SC TAA Mod
 No supported Transceivers
JG664A
HP 7500 Load Balancing Module
 No supported Transceivers
JD252A
HP 7500 NetStream Monitoring Module
 No supported Transceivers
JD254A
c04111585 — DA – 13805 Worldwide — Version 35 — July 3, 2014
Page 18
QuickSpecs
HP 7500 Switch Series
Configuration
HP 7500 SSL VPN Module w/500-user Lic
 No supported Transceivers
JD253A
HP S1200N IPS A7500 Module
 No supported Transceivers
JC527A
HP 7500 48-port 10/100BASE-T Module
 No supported Transceivers
JD198B
See Configuration
Note:7, 8,14
HP 7500 48-port Gig-T PoE-ready Module
 min=0 \ max=2 SFP Transceivers
JD199B
See Configuration
Note:7, 8,14
HP 7500 Advanced VPN Firewall Module
 min=0 \ max=2 SFP Transceivers
JD249A
See Configuration
Note:13
HP 10500/11900/7500 20Gbps VPN FW Mod
 min=0 \ max=2 SFP Transceivers
JG372A
See Configuration
Note:13
HP 7500 4-port 40GbE QSFP+ SC Module
 min=0 \ max=4 QSFP+ Transceivers
JC792A
See Configuration
Note:10
HP 7500 4-port 40GbE CFP SC Module
 min=0 \ max=4 CFP Transceivers
JG373A
See Configuration
Note:11
HP 10500/7500 20G Unified Wired-WLAN Mod
 No supported Transceivers
JG639A
See Configuration
Note:15
Configuration Rules:
Note 1
The following Transceivers install into this Module: (Use #0D1 if switch is CTO)
HP X170 1G SFP LC LH70 1550 Transceiver
HP X170 1G SFP LC LH70 1570 Transceiver
HP X170 1G SFP LC LH70 1590 Transceiver
HP X170 1G SFP LC LH70 1610 Transceiver
HP X170 1G SFP LC LH70 1470 Transceiver
HP X170 1G SFP LC LH70 1490 Transceiver
HP X170 1G SFP LC LH70 1510 Transceiver
HP X170 1G SFP LC LH70 1530 Transceiver
c04111585 — DA – 13805 Worldwide — Version 35 — July 3, 2014
JD109A
JD110A
JD111A
JD112A
JD113A
JD114A
JD115A
JD116A
Page 19
QuickSpecs
HP 7500 Switch Series
Configuration
Note 2
Note 3
Note 4
Note 5
HP X120 1G SFP LC LH100 Transceiver
HP X125 1G SFP LC LH40 1310nm Transceiver
HP X120 1G SFP LC LH40 1550nm Transceiver
HP X125 1G SFP LC LH70 Transceiver
HP X120 1G SFP RJ45 T Transceiver
HP X120 1G SFP LC SX Transceiver
HP X120 1G SFP LC LX Transceiver
HP X120 1G SFP LC BX 10-U Transceiver
HP X120 1G SFP LC BX 10-D Transceiver
HP X110 100M SFP LC LH40 Transceiver
HP X110 100M SFP LC LH80 Transceiver
HP X115 100M SFP LC FX Transceiver
HP X110 100M SFP LC LX Transceiver
HP X115 100M SFP LC BX 10-U Transceiver
HP X115 100M SFP LC BX 10-D Transceiver
JD103A
JD061A
JD062A
JD063B
JD089B
JD118B
JD119B
JD098B
JD099B
JD090A
JD091A
JD102B
JD120B
JD100A
JD101A
The following Transceivers install into this Module: (Use #0D1 if switch is CTO)
HP X110 100M SFP LC LH40 Transceiver
HP X110 100M SFP LC LH80 Transceiver
HP X110 100M SFP LC BX 10-U Transceiver
HP X110 100M SFP LC BX 10-D Transceiver
HP X115 100M SFP LC FX Transceiver
HP X110 100M SFP LC LX Transceiver
JD090A
JD091A
JD100A
JD101A
JD102B
JD120B
The following Transceivers install into this Module: (Use #0D1or #B01 if switch is
CTO)
HP X130 10G SFP+ LC SR Transceiver
HP X130 10G SFP+ LC LRM Transceiver
HP X130 10G SFP+ LC LR Transceiver
HP X240 10G SFP+ to SFP+ 0.65m Direct Attach Copper Cable
HP X240 10G SFP+ to SFP+ 1.2m Direct Attach Copper Cable
HP X240 10G SFP+ to SFP+ 3m Direct Attach Copper Cable
HP X240 10G SFP+ to SFP+ 5m Direct Attach Copper Cable
HP X240 10G SFP+ 7m Direct Attach Copper Cable
The following Transceivers install into this Module: (Use #0D1 if switch is CTO)
HP X135 10G XFP LC ER Transceiver
HP X130 10G XFP LC LR Single Mode 10km 1310nm Transceiver
HP X130 10G XFP LC SR Transceiver
HP X130 10G XFP LC ZR Single Mode 80km 1550nm Transceiver
HP X180 10G XFP LC LH 80km 1538.98nm DWDM Transceiver
HP X180 10G XFP LC LH 80km 1539.77nm DWDM Transceiver
HP X180 10G XFP LC LH 80km 1540.56nm DWDM Transceiver
HP X180 10G XFP LC LH 80km 1542.14nm DWDM Transceiver
HP X180 10G XFP LC LH 80km 1542.94nm DWDM Transceiver
HP X180 10G XFP LC LH 80km 1558.98nm DWDM Transceiver
HP X180 10G XFP LC LH 80km 1559.79nm DWDM Transceiver
HP X180 10G XFP LC LH 80km 1560.61nm DWDM Transceiver
JD092A
JD093A
JD094A
JD095C
JD096C
JD097C
JG081C
JD121A
JD108B
JD117B
JD107A
JG226A
JG227A
JG228A
JG229A
JG230A
JG231A
JG232A
JG233A
The following Transceivers install into this Module: (Use #0D1 if switch is CTO)
c04111585 — DA – 13805 Worldwide — Version 35 — July 3, 2014
Page 20
QuickSpecs
HP 7500 Switch Series
Configuration
Note 6
Note 7
HP X170 1G SFP LC LH70 1550 Transceiver
HP X170 1G SFP LC LH70 1570 Transceiver
HP X170 1G SFP LC LH70 1590 Transceiver
HP X170 1G SFP LC LH70 1610 Transceiver
HP X170 1G SFP LC LH70 1470 Transceiver
HP X170 1G SFP LC LH70 1490 Transceiver
HP X170 1G SFP LC LH70 1510 Transceiver
HP X170 1G SFP LC LH70 1530 Transceiver
HP X120 1G SFP LC LH100 Transceiver
HP X125 1G SFP LC LH40 1310nm Transceiver
HP X120 1G SFP LC LH40 1550nm Transceiver
HP X125 1G SFP LC LH70 Transceiver
HP X120 1G SFP RJ45 T Transceiver
HP X120 1G SFP LC SX Transceiver
HP X120 1G SFP LC LX Transceiver
HP X120 1G SFP LC BX 10-U Transceiver
HP X120 1G SFP LC BX 10-D Transceiver
HP X110 100M SFP LC LH40 Transceiver
HP X110 100M SFP LC LH80 Transceiver
HP X115 100M SFP LC FX Transceiver
HP X110 100M SFP LC LX Transceiver
HP X135 10G XFP LC ER Transceiver
HP X130 10G XFP LC LR Single Mode 10km 1310nm Transceiver
HP X130 10G XFP LC SR Transceiver
HP X130 10G XFP LC ZR Single Mode 80km 1550nm Transceiver
JD109A
JD110A
JD111A
JD112A
JD113A
JD114A
JD115A
JD116A
JD103A
JD061A
JD062A
JD063B
JD089B
JD118B
JD119B
JD098B
JD099B
JD090A
JD091A
JD102B
JD120B
JD121A
JD108B
JD117B
JD107A
The following Transceivers install into this Module: (Use #0D1 if switch is CTO)
HP X170 1G SFP LC LH70 1550 Transceiver
HP X170 1G SFP LC LH70 1570 Transceiver
HP X170 1G SFP LC LH70 1590 Transceiver
HP X170 1G SFP LC LH70 1610 Transceiver
HP X170 1G SFP LC LH70 1470 Transceiver
HP X170 1G SFP LC LH70 1490 Transceiver
HP X170 1G SFP LC LH70 1510 Transceiver
HP X170 1G SFP LC LH70 1530 Transceiver
HP X120 1G SFP LC LH100 Transceiver
HP X125 1G SFP LC LH40 1310nm Transceiver
HP X120 1G SFP LC LH40 1550nm Transceiver
HP X125 1G SFP LC LH70 Transceiver
HP X120 1G SFP RJ45 T Transceiver
HP X120 1G SFP LC SX Transceiver
HP X120 1G SFP LC LX Transceiver
HP X120 1G SFP LC BX 10-U Transceiver
HP X120 1G SFP LC BX 10-D Transceiver
HP X115 100M SFP LC BX 10-U Transceiver
HP X115 100M SFP LC BX 10-D Transceiver
JD109A
JD110A
JD111A
JD112A
JD113A
JD114A
JD115A
JD116A
JD103A
JD061A
JD062A
JD063B
JD089B
JD118B
JD119B
JD098B
JD099B
JD100A
JD101A
This Module is not supported on the JD242x and JD243x at this time.
c04111585 — DA – 13805 Worldwide — Version 35 — July 3, 2014
Page 21
QuickSpecs
HP 7500 Switch Series
Configuration
Note 8
The following DIMMs install into this Module: (Use #0D1 if switch is CTO)
HP 7500 PoE DIMM Memory Module
HP 7500 24-port PoE DIMM
JD192B
JC671A
Note 10
The following 40G Transceivers install into this switch: (Use #0D1or #B01 if switch is CTO)
HP X140 40G QSFP+ LC LR4 SM 10km 1310nm Transceiver
JG661A
HP X140 40G QSFP+ MPO SR4 Transceiver
JG325B
HP X140 40G QSFP+ MPO MM 850nm CSR4 300m Transceiver
JG709A
HP X240 40G QSFP+ QSFP+ 1m Direct Attach Copper Cable
JG326A
HP X240 40G QSFP+ QSFP+ 3m Direct Attach Copper Cable
JG327A
HP X240 40G QSFP+ QSFP+ 5m Direct Attach Copper Cable
JG328A
HP X240 40G QSFP+ to 4x10G SFP+ 1m Direct Attach Copper Splitter Cable
JG329A
HP X240 40G QSFP+ to 4x10G SFP+ 3m Direct Attach Copper Splitter Cable
JG330A
HP X240 40G QSFP+ to 4x10G SFP+ 5m Direct Attach Copper Splitter Cable
JG331A
Note 11
The following CFP Transceivers install into this switch:
HP X140 40G CFP LC LR4 10km SM Transceiver
Note 12
The following PoE DIMM installs into this Module: (Use #0D1 if switch is CTO)
The JC671A - HP A7500 24-port PoE DIMM (must be installed to enable PoE on the
these modules)
Note 13
HP X125 1G SFP LC LH40 1310nm Transceiver
HP X120 1G SFP LC LH40 1550nm Transceiver
HP X125 1G SFP LC LH70 Transceiver
HP X120 1G SFP LC SX Transceiver
HP X120 1G SFP LC LX Transceiver
Note 14
The following PoE DIMM installs into this Module: (Use #0D1 if switch is CTO)
JD192B - HP 7500 PoE DIMM Module (must be installed to enable PoE on the these
modules)
Note 15
Maximum of this Module per Chassis:
JD238B min=0\max=9 per Chassis
JG509A min=0\max=7 per Chassis
JD239B, JD241B min=0\max=5 per Chassis
JG508A min=0\max=3 per Chassis
JD240B, JD243B min=0\max=2 per Chassis
JD242B, JG507A min=0\max=1 per Chassis
There are no restrictions on which slots these modules may go in.
Remark
JD253A - Additional User licenses available below in the 'Switch Enclosure Options'
category.
JG639A and JG645A - Additional AP licenses available below in the 'Switch Enclosure
Options' category.
JC857A
JD061A
JD062A
JD063B
JD118B
JD119B
Fabric Modules
System (std 0 // max 2) User Selection (min 1 // max 2) per enclosure
c04111585 — DA – 13805 Worldwide — Version 35 — July 3, 2014
See Configuration
Note:3, 12
Page 22
QuickSpecs
HP 7500 Switch Series
Configuration
JG507A, JG508A and JG509A only System (std 1 // max 2) User Selection (min 0 // max 1) per enclosure
See Configuration
Note:3, 12
HP 7500 384Gbps Fab Mod w/2 XFP Ports
 min=0 \ max=2 XFP Transceivers
JD193B
See Configuration
Note:1, 4
HP 7500 384Gbps Fabric Module
 No supported Transceivers
JD194B
See Configuration
Note:1
HP 7500 384Gbps Fab Mod w/12 SFP Ports
 min=0 \ max=12 SFP Transceivers
JD224A
See Configuration
Note:1, 5
HP 7500 384Gbps Advanced Fabric Module
 No supported Transceivers
JD195A
See Configuration
Note:1
HP 7500 384Gbps Lite Fabric Module
 No supported Transceivers
JF219B
See Configuration
Note:1
HP 7500 768Gbps Fabric Module
 No supported Transceivers
JD220A
See Configuration
Note:11
HP 7502 Fabric Module
 No supported Transceivers
JD196A
See Configuration
Note:10
HP 7503 Fabric Module with 24 GbE Ports
 min=0 \ max=24 SFP Transceivers
JD222A
See Configuration
Note:2, 5
HP A7503-S 144 Gbps Fab/MPU w 24p Gig-T
 min=0 \ max=4 SFP Transceivers
JC666A
See Configuration
Note:2, 5,13
Configuration Rules:
Note 1
Note 2
These Modules install to the following switches: (Use #0D1 if switch is CTO)
HP A7503 Switch Chassis
HP A7506 Switch Chassis
HP 7506 Switch with 2 48-port Gig-T PoE+ Modules and 384Gbps MPU with 2 XFP ports
HP A7506 Vertical Switch Chassis
HP A7510 Switch Chassis
HP 7510 Switch with 2 48-port Gig-T PoE+ Modules and 768Gbps MPU
JD240x
JD239x
JG508A
JD241x
JD238x
JG509A
These Modules install to the following switches only: (Use #0D1 if switch is CTO)
c04111585 — DA – 13805 Worldwide — Version 35 — July 3, 2014
Page 23
QuickSpecs
HP 7500 Switch Series
Configuration
HP A7503 Switch Chassis with 1 Fabric Slot
HP 7503 Switch with 48-port Gig-T PoE+ Module and 384Gbps MPU with 2 XFP ports
JD243x
JG507A
Note 3
If JD243x or JG507A is selected then Max = 1.
Note 4
The following Transceivers install into this Module: (Use #0D1 if switch is CTO)
HP X135 10G XFP LC ER Transceiver
HP X130 10G XFP LC LR Single Mode 10km 1310nm Transceiver
HP X130 10G XFP LC SR Transceiver
HP X130 10G XFP LC ZR Single Mode 80km 1550nm Transceiver
HP X180 10G XFP LC LH 80km 1538.98nm DWDM Transceiver
HP X180 10G XFP LC LH 80km 1539.77nm DWDM Transceiver
HP X180 10G XFP LC LH 80km 1540.56nm DWDM Transceiver
HP X180 10G XFP LC LH 80km 1542.14nm DWDM Transceiver
HP X180 10G XFP LC LH 80km 1542.94nm DWDM Transceiver
HP X180 10G XFP LC LH 80km 1558.98nm DWDM Transceiver
HP X180 10G XFP LC LH 80km 1559.79nm DWDM Transceiver
HP X180 10G XFP LC LH 80km 1560.61nm DWDM Transceiver
JD121A
JD108B
JD117B
JD107A
JG226A
JG227A
JG228A
JG229A
JG230A
JG231A
JG232A
JG233A
The following Transceivers install into this Module: (Use #0D1 if switch is CTO)
HP X170 1G SFP LC LH70 1550 Transceiver
HP X170 1G SFP LC LH70 1570 Transceiver
HP X170 1G SFP LC LH70 1590 Transceiver
HP X170 1G SFP LC LH70 1610 Transceiver
HP X170 1G SFP LC LH70 1470 Transceiver
HP X170 1G SFP LC LH70 1490 Transceiver
HP X170 1G SFP LC LH70 1510 Transceiver
HP X170 1G SFP LC LH70 1530 Transceiver
HP X120 1G SFP LC LH100 Transceiver
HP X125 1G SFP LC LH40 1310nm Transceiver
HP X120 1G SFP LC LH40 1550nm Transceiver
HP X125 1G SFP LC LH70 Transceiver
HP X120 1G SFP RJ45 T Transceiver
HP X120 1G SFP LC SX Transceiver
HP X120 1G SFP LC LX Transceiver
HP X120 1G SFP LC BX 10-U Transceiver
HP X120 1G SFP LC BX 10-D Transceiver
HP X110 100M SFP LC LH40 Transceiver
HP X110 100M SFP LC LH80 Transceiver
HP X115 100M SFP LC FX Transceiver
HP X110 100M SFP LC LX Transceiver
HP X115 100M SFP LC BX 10-U Transceiver
HP X115 100M SFP LC BX 10-D Transceiver
JD109A
JD110A
JD111A
JD112A
JD113A
JD114A
JD115A
JD116A
JD103A
JD061A
JD062A
JD063B
JD089B
JD118B
JD119B
JD098B
JD099B
JD090A
JD091A
JD102B
JD120B
JD100A
JD101A
These Modules install to the following switches only: (Use #0D1 if switch is CTO)
HP A7502 Switch Chassis
JD242x
These Modules install to the following switches only: (Use #0D1 if switch is CTO)
HP A7510 Switch Chassis
JD238x
Note 5
Note 10
Note 11
c04111585 — DA – 13805 Worldwide — Version 35 — July 3, 2014
Page 24
QuickSpecs
HP 7500 Switch Series
Configuration
HP 7510 Switch with 2 48-port Gig-T PoE+ Modules and 768Gbps MPU
Note 12
If 2 Fabric Modules are selected they must be the same Sku number.
Note 13
The following PoE DIMM installs into this Module: (Use #0D1 if switch is CTO)
The JC671A - HP A7500 24-port PoE DIMM (must be installed to enable PoE on the these
modules)
Remarks:
For Switch A7503,A7506 and A7506-V, these modules can only be inserted into the Slot 0
and Slot 1. And for Switch A7510, this module can only be inserted into the Slot 5 and Slot 6.
For Switch A7503-S, this module can only be inserted into the Slot 0.
JG509A
A7500 PoE Module
System (std 0 // max 1) User Selection (min 0 // max 1) per Ethernet or Fabric Module
HP 7500 PoE DIMM Module
JD192B
See
Configuration
Note:1, 3, 5, 6
HP A7500 24-port PoE DIMM
JC671A
See
Configuration
Note:2, 4, 5, 6
Configuration Rules:
Note 1
The JD192B is optional when you have selected the JD199B, JD198B, JD210A, JC709A,
JC710A or JD228B modules.
Note 2
If this DIMM is selected at least one JD219A - HP A7500 2800W AC Power Supply is
required. (Except for JD242x, and JD243x, see rule 6)
Note 3
If 1 or more of the JD192B (PoE DIMM Module) is ordered than the customer must also
order 2 of JD208A, JD218A, JD219A, or JD227A in order to support PoE. (Except for
JD242x, and JD243x, see rule 6)
Note 4
The JC671A is optional when you have selected the JC666A, JC669A or JC668A
modules.
Note 5
This Module is not supported on JG507A at this time.
Note 6
This Module is supported on the JD242x, and JD243x only when an External DC Power
Source is connected to the rear terminals. (See Installation Guide)
Transceivers
SFP+ Transceivers
HP X130 10G SFP+ LC SR Transceiver
c04111585 — DA – 13805 Worldwide — Version 35 — July 3, 2014
JD092B
Page 25
QuickSpecs
HP 7500 Switch Series
Configuration
HP X130 10G SFP+ LC LRM Transceiver
HP X130 10G SFP+ LC LR Transceiver
HP X240 10G SFP+ SFP+ 0.65m Direct Attach Copper Cable
HP X240 10G SFP+ SFP+ 1.2m Direct Attach Copper Cable
HP X240 10G SFP+ SFP+ 3m Direct Attach Copper Cable
HP X240 10G SFP+ SFP+ 5m Direct Attach Copper Cable
HP X240 10G SFP+ 7m Direct Attach Copper Cable
JD093B
JD094B
JD095C#B01
JD096C#B01
JD097C#B01
JG081C#B01
JC784C#B01
SFP Transceivers
HP X170 1G SFP LC LH70 1550 Transceiver
HP X170 1G SFP LC LH70 1570 Transceiver
HP X170 1G SFP LC LH70 1590 Transceiver
HP X170 1G SFP LC LH70 1610 Transceiver
HP X170 1G SFP LC LH70 1470 Transceiver
HP X170 1G SFP LC LH70 1490 Transceiver
HP X170 1G SFP LC LH70 1510 Transceiver
HP X170 1G SFP LC LH70 1530 Transceiver
HP X120 1G SFP LC LH100 Transceiver
HP X125 1G SFP LC LH40 1310nm XCVR
HP X120 1G SFP LC LH40 1550nm XCVR
HP X120 1G SFP RJ45 T Transceiver
HP X120 1G SFP LC SX Transceiver
HP X120 1G SFP LC LX Transceiver
HP X125 1G SFP LC LH70 Transceiver
HP X120 1G SFP LC BX 10-U Transceiver
HP X120 1G SFP LC BX 10-D Transceiver
HP X110 100M SFP LC LH40 Transceiver
HP X110 100M SFP LC LH80 Transceiver
HP X115 100M SFP LC FX Transceiver
HP X110 100M SFP LC LX Transceiver
HP X110 100M SFP LC BX 10-U Transceiver
HP X110 100M SFP LC BX 10-D Transceiver
JD109A
JD110A
JD111A
JD112A
JD113A
JD114A
JD115A
JD116A
JD103A
JD061A
JD062A
JD089B
JD118B
JD119B
JD063B
JD098B
JD099B
JD090A
JD091A
JD102B
JD120B
JD100A
JD101A
XFP Transceivers
HP X135 10G XFP LC ER Transceiver
HP X130 10G XFP LC ZR 1550nm Transceiver
HP X130 10G XFP LC SR Transceiver
HP X130 10G XFP LC LR 1310nm Transceiver
HP X180 10G XFP LC 1538.98 DWDM Xcvr
HP X180 10G XFP LC 1539.77 DWDM Xcvr
HP X180 10G XFP LC 1540.56 DWDM Xcvr
HP X180 10G XFP LC 1542.14 DWDM Xcvr
HP X180 10G XFP LC 1542.94 DWDM Xcvr
HP X180 10G XFP LC 1558.98 DWDM Xcv
HP X180 10G XFP LC 1559.79 DWDM Xcvr
HP X180 10G XFP LC 1560.61 DWDM Xcvr
c04111585 — DA – 13805 Worldwide — Version 35 — July 3, 2014
JD121A
JD107A
JD117B
JD108B
JG226A
JG227A
JG228A
JG229A
JG230A
JG231A
JG232A
JG233A
Page 26
QuickSpecs
HP 7500 Switch Series
Configuration
QSFP+ Transceivers
HP X140 40G QSFP+ LC LR4 SM XCVR
HP X140 40G QSFP+ MPO SR4 XCVR
HP X140 40G QSFP+ CSR4 300m XCVR
HP X240 40G QSFP+ QSFP+ 1m Direct Attach Copper Cable
HP X240 40G QSFP+ QSFP+ 3m Direct Attach Copper Cable
HP X240 40G QSFP+ QSFP+ 5m Direct Attach Copper Cable
HP X240 QSFP+ 4x10G SFP+ 1m Direct Attach Copper Cable
HP X240 QSFP+ 4x10G SFP+ 3m Direct Attach Copper Cable
HP X240 QSFP+ 4x10G SFP+ 5m Direct Attach Copper Cable
JG661A
JG325B
JG709A
JG326A#B01
JG327A#B01
JG328A#B01
JG329A#B01
JG330A#B01
JG331A#B01
CFP Transceivers
HP X140 40G CFP LC LR4 10km SM Transceiver
JC857A
Switch Enclosure Options
Software Licenses
HP 10500/7500 Wrd-WLAN Mod 128 AP E-LTU
 (min 0 // max 7)
REMARK: This license is for use with the Redundant Controllers.
JG649AAE
See
Configuration
Note:1
HP Unified Wired-WLAN 128 AP Redundant E-LTU
 (min 0 // max 7)
REMARK: This license is for use with the Redundant Controllers.
JG902AAE
See
Configuration
Note:1
Configuration Rules:
Note 1
Only supported on JG639A and JG645A.
Compact Flash cards
System (std 0 // max 1) User Selection (min 0 // max 1)
HP X600 1G Compact Flash Card
JC684A
See
Configuration
Note:1
HP X600 512M Compact Flash Card
JC685A
See
Configuration
Note:1
HP X600 256M Compact Flash Card
JC686A
c04111585 — DA – 13805 Worldwide — Version 35 — July 3, 2014
Page 27
QuickSpecs
HP 7500 Switch Series
Configuration
See
Configuration
Note:1
Configuration Rules:
Note 1
These CF Cards are supported on the following Modules only:
HP 7502 Fabric Module
HP 7500 384Gbps Fabric Module with 2 XFP Ports
HP 7500 384Gbps Fabric Module
HP 7500 768Gbps Fabric Module
HP 7500 384Gbps Advanced Fabric Module
HP 7500 384Gbps Lite Fabric Module
HP 7500 384Gbps Fabric Module with 12 SFP Ports
HP 7502 TAA-compliant Main Processing Unit
HP 7500 384Gbps TAA-compliant Fabric / MPU with 2 10GbE XFP Ports
HP 7500 384Gbps TAA-compliant Fabric / Main Processing Unit
HP 7500 768Gbps TAA-compliant Fabric / Main Processing Unit
HP 7503-S 144Gbps Fabric/MPU with PoE Upgradable 20-port Gig-T/4-port GbE
Combo
HP 9500 VPN Firewall Module
JD196A
JD193B
JD194B
JD220A
JD195A
JF219B
JD224A
JC697A
JC699A
JC700A
JC701A
JC666A
JD245A
Options for the SSL VPN Service Board Modules (JD253x)
HP 7500 SSL VPN 1000-user License
 min=0\ max=10 per SSL
JD257A
See
Configuration
Note:1
HP 7500 SSL VPN 1000-user License
 min=0\ max=10 per SSL
JD257AAE
See
Configuration
Note:1
Configuration Rules:
Note 1
Any mixture of (JD257A) that equals 10,000 LTU's is the max per any JD253A module the maximum
would be based on the module and not the entire switch.
Options for the S1200N IPS A7500 Module (JC527A)
System (std 0 // max - no limit) User Selection (min 0 // max - no limit) per S1200N IPS A7500 Module
HP A7500 S1200N 1-y Rep DV Subsc Svc
JC592A
See
Configuration
Note:1
HP A7500 S1200N 3-y Rep DV Subsc Svc
JC593A
See
Configuration
c04111585 — DA – 13805 Worldwide — Version 35 — July 3, 2014
Page 28
QuickSpecs
HP 7500 Switch Series
Configuration
Note:1
Configuration Rules:
Note 1
If any DV Subsc Svc is selected #0D1, it must be integrated to one of the following modules:
JC527A - HP S1200N IPS A7500 Module
Spare Fan Assembly
HP 7502 Spare Fan Assembly
HP 7503 Spare Fan Assembly
HP 7506 Spare Fan Assembly
HP 7506-V Spare Fan Assembly
HP 7510 Spare Fan Assembly
HP 7503-S Spare Fan Assembly
JD213A
JD212A
JD214A
JD215A
JD216A
JC672A
Remarks:
JD213A - This item is only used to replace the fan module of an A7502 . A host is delivered with the fan
module.
JD212A - This item is only used to replace the fan module of an A7503. A host is delivered with the fan
module.
JD214A - This item is only used to replace the fan module of an A7506. A host is delivered with the fan
module.
JD215A - This item is only used to replace the fan module of an A7506-V. A host is delivered with the fan
module.
JD216A - This item is only used to replace the fan module of an A7510. A host is delivered with the fan
module.
JC672A - This item is only used to replace the fan module of an A7503-S. A host is delivered with the fan
module.
Opacity Shield Kit
System (std 0 // max 1) User Selection (min 0 // max 1)
HP 7510 Opcty Shld Kit
NOTE:
Supported on JD238B
JG565A
HP 7506 Opcty Shld Kit
NOTE:
Supported on JD239B, JD241B
JG566A
HP 7503 Opcty Shld Kit
NOTE:
Supported on JD240B, JD243B
JG568A
c04111585 — DA – 13805 Worldwide — Version 35 — July 3, 2014
Page 29
QuickSpecs
HP 7500 Switch Series
Configuration
Tamper Evidence Labels
HP 12mm x 60mm Tmpr-Evidence (100) Lbl
NOTE:
Supported on JG565A, JG566A or JG568A
Remarks:
JG586A
Each JG565A, JG566A or JG568A would use 1 of JG586A.
c04111585 — DA – 13805 Worldwide — Version 35 — July 3, 2014
Page 30
QuickSpecs
HP 7500 Switch Series
Technical Specifications
HP 7510 Switch Chassis (JD238B)
Included accessories
1 HP 7510 Spare Fan Assembly (JD216A)
I/O ports and slots
10 I/O module slots
Supports a maximum of 84 10GbE ports or 480 autosensing 10/100/1000 ports or 480 SFP ports or 40
40GbE ports, or a combination
Additional ports and
2 switch fabric slots
slots
Power supplies
2 power-supply slots
1 minimum power-supply required (ordered separately)
Fan tray
includes: 1 x JD216A
1 fan tray slot
Physical characteristics Dimensions
17.17(w) x 16.54(d) x 27.87(h) in (43.6 x 42.0 x 70.8 cm) (16U height)
Weight
211 lb (95.71 kg), Fully loaded chassis, two fabrics, two power supplies,
and a full complement of typical I/O modules
Memory and processor
Fabric
MIPS64 @ 600 MHz, 64 MB flash, 512 MB RAM
I/O Module
MIPS64 @ 400 MHz, 512 MB RAM
Mounting
Mounts in an EIA-standard 19 in. rack or other equipment cabinet (hardware included); horizontal
surface mounting only
Performance
Throughput
714 million pps
Routing/Switching
1152 Gb/s
capacity
Routing table size
256000 entries (IPv4), 8000 entries (IPv6)
MAC address table size
512000 entries
Reliability
Availability
99.999%
Environment
Operating temperature 32°F to 113°F (0°C to 45°C)
Operating relative
10% to 95%, non-condensing
humidity
Nonoperating/Storage
-40°F to 158°F (-40°C to 70°C)
temperature
Nonoperating/Storage
5% to 95%, non-condensing
relative humidity
Acoustic
Low-speed fan: 53.5 dB, High-speed fan: 56.7 dB
Electrical characteristics Frequency
50 / 60 Hz
AC Voltage
100-120 / 200-240 VAC
Current
16/50 A
Power output
1400 W
Notes
Based on a common power supply of 1400 W (AC/DC)
Safety
UL 60950-1; IEC 60950-1; CAN/CSA-C22.2 No. 60950-1; EN 60950-1/A11
Emissions
VCCI Class A
EN 55022 Class A
ICES-003 Class A
ANSI C63.4 2003
AS/NZS CISPR 22 Class A
EN 61000-3-2:2006
EN 61000-3-3:1995 +A1:2001+A2:2005
EMC Directive 2004/108/EC
FCC (CFR 47, Part 15) Class A
c04111585 — DA – 13805 Worldwide — Version 35 — July 3, 2014
Page 31
QuickSpecs
HP 7500 Switch Series
Technical Specifications
Immunity
Management
Notes
Services
Generic
ETSI EN 300 386 V1.3.3
EN
EN 61000-4-2:1995+A1:1998+A2:2001
ESD
EN 61000-4-2
Radiated
EN 61000-4-3
EFT/Burst
EN 61000-4-4
Surge
EN 61000-4-5
Conducted
EN 61000-4-6
Power frequency
IEC 61000-4-8
magnetic field
Voltage dips and
EN 61000-4-11
interruptions
Harmonics
EN 61000-3-2, IEC 61000-3-2
Flicker
EN 61000-3-3, IEC 61000-3-3
IMC - Intelligent Management Center; command-line interface; Web browser; out-of-band
management (serial RS-232C); SNMP Manager; Telnet; terminal interface (serial RS-232C); modem
interface; IEEE 802.3 Ethernet MIB; Ethernet Interface MIB
For non-TAA environments, IPS/IDS functionality is provided by the HP S1200E IPS 7500 Module
(JC527A).
For non-TAA environments, IKE/IPSec functionality is provided by the HP 7500 VPN Firewall Module
(JD249A).
IRF functionality is not supported on HP 7502 and 7503-S Switch Chassis.
3-year, parts only, global next-day advance exchange (HP781E)
3-year, 4-hour onsite, 13x5 coverage for hardware (HP782E)
3-year, 4-hour onsite, 24x7 coverage for hardware (HP785E)
3-year, 4-hour onsite, 24x7 coverage for hardware, 24x7 software phone support (HP788E)
3-year, 24x7 SW phone support, software updates (HP791E)
1-year, post-warranty, 4-hour onsite, 24x7 coverage for hardware, 24x7 software phone support
(HR511E)
Installation with minimum configuration, system-based pricing (UX032E)
4-year, 4-hour onsite, 13x5 coverage for hardware (HP783E)
4-year, 4-hour onsite, 24x7 coverage for hardware (HP786E)
4-year, 4-hour onsite, 24x7 coverage for hardware, 24x7 software phone (HP789E)
4-year, 24x7 SW phone support, software updates (HP792E)
5-year, 4-hour onsite, 13x5 coverage for hardware (HP784E)
5-year, 4-hour onsite, 24x7 coverage for hardware (HP787E)
5-year, 4-hour onsite, 24x7 coverage for hardware, 24x7 software phone (HP790E)
5-year, 24x7 SW phone support, software updates (HP793E)
3 Yr 6 hr Call-to-Repair Onsite (HP795E)
3 Yr 6 hr Call-to-Repair Onsite (HP794E)
5 Yr 6 hr Call-to-Repair Onsite (HP796E)
1-year, 4-hour onsite, 13x5 coverage for hardware (HR509E)
1-year, 4-hour onsite, 24x7 coverage for hardware (HR510E)
1-year, 6 hour Call-To-Repair Onsite for hardware (HR513E)
1-year, 24x7 software phone support, software updates (HR512E)
Refer to the HP website at: www.hp.com/networking/services for details on the service-level
descriptions and product numbers. For details about services and response times in your area, please
contact your local HP sales office.
HP 7506-V Switch Chassis (JD241B)
Included accessories
1 HP 7506-V Spare Fan Assembly (JD215A)
I/O ports and slots
6 I/O module slots
c04111585 — DA – 13805 Worldwide — Version 35 — July 3, 2014
Page 32
QuickSpecs
HP 7500 Switch Series
Technical Specifications
Additional ports and
slots
Power supplies
Supports a maximum of 52 10GbE ports or 288 autosensing 10/100/1000 ports or 288 SFP ports or 24
40GbE ports, or a combination
2 switch fabric slots
2 power-supply slots
1 minimum power-supply required (ordered separately)
Fan tray
includes: 1 x JD215A
1 fan tray slot
Physical characteristics Dimensions
17.17(w) x 16.54(d) x 36.61(h) in (43.6 x 42.0 x 93.0 cm) (21U height)
Weight
222 lb (100.7 kg), Fully loaded chassis, two fabrics, two power supplies,
and a full complement of typical I/O modules
Memory and processor
Fabric
MIPS64 @ 600 MHz, 64 MB flash, 512 MB RAM
I/O Module
MIPS64 @ 400 MHz, 512 MB RAM
Mounting
Mounts in an EIA-standard 19 in. rack or other equipment cabinet (hardware included); horizontal
surface mounting only
Performance
Throughput
488 million pps
Routing/Switching
768 Gb/s
capacity
Routing table size
256000 entries (IPv4), 8000 entries (IPv6)
MAC address table size
512000 entries
Reliability
Availability
99.999%
Environment
Operating temperature 32°F to 113°F (0°C to 45°C)
Operating relative
10% to 95%, non-condensing
humidity
Nonoperating/Storage
-40°F to 158°F (-40°C to 70°C)
temperature
Nonoperating/Storage
5% to 95%, non-condensing
relative humidity
Acoustic
Low-speed fan: 52.1 dB, High-speed fan: 56.2 dB
Electrical characteristics Frequency
50/60 Hz
AC Voltage
100-120 / 200-240 VAC
Current
16/50 A
Power output
1400 W
Notes
Based on a common power supply of 1400 W (AC/DC)
Safety
UL 60950-1; IEC 60950-1; CAN/CSA-C22.2 No. 60950-1; EN 60950-1/A11
Emissions
VCCI Class A
EN 55022 Class A
ICES-003 Class A
ANSI C63.4 2003
AS/NZS CISPR 22 Class A
EN 61000-3-2:2006
EN 61000-3-3:1995 +A1:2001+A2:2005
EMC Directive 2004/108/EC
FCC (CFR 47, Part 15) Class A
Immunity
Generic
ETSI EN 300 386 V1.3.3
EN
EN 61000-4-2:1995+A1:1998+A2:2001
ESD
EN 61000-4-2
Radiated
EN 61000-4-3
c04111585 — DA – 13805 Worldwide — Version 35 — July 3, 2014
Page 33
QuickSpecs
HP 7500 Switch Series
Technical Specifications
Management
Notes
Services
EFT/Burst
EN 61000-4-4
Surge
EN 61000-4-5
Conducted
EN 61000-4-6
Power frequency
IEC 61000-4-8
magnetic field
Voltage dips and
EN 61000-4-11
interruptions
Harmonics
EN 61000-3-2, IEC 61000-3-2
Flicker
EN 61000-3-3, IEC 61000-3-3
IMC - Intelligent Management Center; command-line interface; Web browser; out-of-band
management (serial RS-232C); SNMP Manager; Telnet; terminal interface (serial RS-232C); modem
interface; IEEE 802.3 Ethernet MIB; Ethernet Interface MIB
For non-TAA environments, IPS/IDS functionality is provided by the HP S1200E IPS 7500 Module
(JC527A).
For non-TAA environments, IKE/IPSec functionality is provided by the HP 7500 VPN Firewall Module
(JD249A).
IRF functionality is not supported on HP 7502 and 7503-S Switch Chassis.
3-year, parts only, global next-day advance exchange (UW999E)
3-year, 4-hour onsite, 13x5 coverage for hardware (UX001E)
3-year, 4-hour onsite, 24x7 coverage for hardware (UX004E)
3-year, 4-hour onsite, 24x7 coverage for hardware, 24x7 software phone support (UX007E)
3-year, 24x7 SW phone support, software updates (UX010E)
1-year, post-warranty, 4-hour onsite, 13x5 coverage for hardware (HR514E)
1-year, post-warranty, 4-hour onsite, 24x7 coverage for hardware (HR515E)
1-year, post-warranty, 4-hour onsite, 24x7 coverage for hardware, 24x7 software phone support
(HR516E)
Installation with minimum configuration, system-based pricing (UX032E)
4-year, 4-hour onsite, 13x5 coverage for hardware (UX002E)
4-year, 4-hour onsite, 24x7 coverage for hardware (UX005E)
4-year, 4-hour onsite, 24x7 coverage for hardware, 24x7 software phone (UX008E)
4-year, 24x7 SW phone support, software updates (UX011E)
5-year, 4-hour onsite, 13x5 coverage for hardware (UX003E)
5-year, 4-hour onsite, 24x7 coverage for hardware (UX006E)
5-year, 4-hour onsite, 24x7 coverage for hardware, 24x7 software phone (UX009E)
5-year, 24x7 SW phone support, software updates (UX012E)
3 Yr 6 hr Call-to-Repair Onsite (UX013E)
4 Yr 6 hr Call-to-Repair Onsite (UX014E)
5 Yr 6 hr Call-to-Repair Onsite (UX015E)
1-year, 6 hour Call-To-Repair Onsite for hardware (HR518E)
1-year, 24x7 software phone support, software updates (HR517E)
Refer to the HP website at: www.hp.com/networking/services for details on the service-level
descriptions and product numbers. For details about services and response times in your area, please
contact your local HP sales office.
HP 7506 Switch Chassis (JD239B)
Included accessories
1 HP 7506 Spare Fan Assembly (JD214A)
I/O ports and slots
6 I/O module slots
Supports a maximum of 52 10GbE ports or 288 autosensing 10/100/1000 ports or 288 SFP ports or 24
40GbE ports, or a combination
Additional ports and
2 switch fabric slots
slots
c04111585 — DA – 13805 Worldwide — Version 35 — July 3, 2014
Page 34
QuickSpecs
HP 7500 Switch Series
Technical Specifications
Power supplies
2 power-supply slots
1 minimum power-supply required (ordered separately)
Fan tray
includes: 1 x JD214A
1 fan tray slot
Physical characteristics Dimensions
17.17(w) x 16.54(d) x 22.64(h) in (43.6 x 42.0 x 57.5 cm) (13U height)
Weight
207 lb (93.9 kg), Fully loaded chassis, two fabrics, two power supplies, and
a full complement of typical I/O modules
Memory and processor
Fabric
MIPS64 @ 600 MHz, 64 MB flash, 512 MB RAM
I/O Module
MIPS64 @ 400 MHz, 512 MB RAM
Mounting
Mounts in an EIA-standard 19 in. rack or other equipment cabinet (hardware included); horizontal
surface mounting only
Performance
Throughput
488 million pps
Routing/Switching
768 Gbps
capacity
Routing table size
256000 entries (IPv4), 8000 entries (IPv6)
MAC address table size
512000 entries
Reliability
Availability
99.999%
Environment
Operating temperature 32°F to 113°F (0°C to 45°C)
Operating relative
10% to 95%, non-condensing
humidity
Nonoperating/Storage
-40°F to 158°F (-40°C to 70°C)
temperature
Nonoperating/Storage
5% to 95%, non-condensing
relative humidity
Acoustic
Low-speed fan: 53.6 dB, High-speed fan: 57.7 dB
Electrical characteristics Frequency
50/60 Hz
Achieved Miercom Certified Green Award
Description
Safety
Emissions
Immunity
The H3C S7506E (HP 7506) is Certified Green in the 2009 Miercom Green
Switches Industry Assessment.
AC Voltage
100-120 / 200-240 VAC
DC Voltage
-48 V / -60 V
Current
16/50 A
Power output
1400 W
Notes
Based on a common power supply of 1400 W (AC/DC)
UL 60950-1; IEC 60950-1; CAN/CSA-C22.2 No. 60950-1; EN 60950-1/A11
VCCI Class A
EN 55022 Class A
ICES-003 Class A
ANSI C63.4 2003
AS/NZS CISPR 22 Class A
EN 61000-3-2:2006
EN 61000-3-3:1995 +A1:2001+A2:2005
EMC Directive 2004/108/EC
FCC (CFR 47, Part 15) Class A
Generic
ETSI EN 300 386 V1.3.3
EN
EN 61000-4-2:1995+A1:1998+A2:2001
ESD
EN 61000-4-2
c04111585 — DA – 13805 Worldwide — Version 35 — July 3, 2014
Page 35
QuickSpecs
HP 7500 Switch Series
Technical Specifications
Management
Notes
Services
Radiated
EN 61000-4-3
EFT/Burst
EN 61000-4-4
Surge
EN 61000-4-5
Conducted
EN 61000-4-6
Power frequency
IEC 61000-4-8
magnetic field
Voltage dips and
EN 61000-4-11
interruptions
Harmonics
EN 61000-3-2, IEC 61000-3-2
Flicker
EN 61000-3-3, IEC 61000-3-3
IMC - Intelligent Management Center; command-line interface; Web browser; out-of-band
management (serial RS-232C); SNMP Manager; Telnet; terminal interface (serial RS-232C); modem
interface; IEEE 802.3 Ethernet MIB; Ethernet Interface MIB
For non-TAA environments, IPS/IDS functionality is provided by the HP S1200E IPS 7500 Module
(JC527A).
For non-TAA environments, IKE/IPSec functionality is provided by the HP 7500 VPN Firewall Module
(JD249A).
IRF functionality is not supported on HP 7502 and 7503-S Switch Chassis.
3-year, parts only, global next-day advance exchange (UW999E)
3-year, 4-hour onsite, 13x5 coverage for hardware (UX001E)
3-year, 4-hour onsite, 24x7 coverage for hardware (UX004E)
3-year, 4-hour onsite, 24x7 coverage for hardware, 24x7 software phone support (UX007E)
3-year, 24x7 SW phone support, software updates (UX010E)
1-year, post-warranty, 4-hour onsite, 13x5 coverage for hardware (HR514E)
1-year, post-warranty, 4-hour onsite, 24x7 coverage for hardware (HR515E)
1-year, post-warranty, 4-hour onsite, 24x7 coverage for hardware, 24x7 software phone support
(HR516E)
Installation with minimum configuration, system-based pricing (UX032E)
4-year, 4-hour onsite, 13x5 coverage for hardware (UX002E)
4-year, 4-hour onsite, 24x7 coverage for hardware (UX005E)
4-year, 4-hour onsite, 24x7 coverage for hardware, 24x7 software phone (UX008E)
4-year, 24x7 SW phone support, software updates (UX011E)
5-year, 4-hour onsite, 13x5 coverage for hardware (UX003E)
5-year, 4-hour onsite, 24x7 coverage for hardware (UX006E)
5-year, 4-hour onsite, 24x7 coverage for hardware, 24x7 software phone (UX009E)
5-year, 24x7 SW phone support, software updates (UX012E)
3 Yr 6 hr Call-to-Repair Onsite (UX013E)
4 Yr 6 hr Call-to-Repair Onsite (UX014E)
5 Yr 6 hr Call-to-Repair Onsite (UX015E)
1-year, 6 hour Call-To-Repair Onsite for hardware (HR518E)
1-year, 24x7 software phone support, software updates (HR517E)
Refer to the HP website at: www.hp.com/networking/services for details on the service-level
descriptions and product numbers. For details about services and response times in your area, please
contact your local HP sales office.
HP 7503 Switch Chassis (JD240B)
Included accessories
1 HP 7503 Spare Fan Assembly (JD212A)
I/O ports and slots
3 I/O module slots
Supports a maximum of 28 10GbE ports or 144 autosensing 10/100/1000 ports or 144 SFP ports or 12
40GbE ports, or a combination
Additional ports and
2 switch fabric slots
c04111585 — DA – 13805 Worldwide — Version 35 — July 3, 2014
Page 36
QuickSpecs
HP 7500 Switch Series
Technical Specifications
slots
Power supplies
2 power-supply slots
1 minimum power-supply required (ordered separately)
Fan tray
includes: 1 x JD212A
1 fan tray slot
Physical characteristics Dimensions
17.17(w) x 16.54(d) x 17.36(h) in (43.6 x 42.0 x 44.1 cm) (10U height)
Weight
147 lb (66.68 kg), Fully loaded chassis, two fabrics, two power supplies,
and a full complement of typical I/O modules
Memory and processor
Fabric
MIPS64 @ 600 MHz, 64 MB flash, 512 MB RAM
I/O Module
MIPS64 @ 400 MHz, 512 MB RAM
Mounting
Mounts in an EIA-standard 19 in. rack or other equipment cabinet (hardware included); horizontal
surface mounting only
Performance
Throughput
274 million pps
Routing/Switching
480 Gbps
capacity
Routing table size
256000 entries (IPv4), 8000 entries (IPv6)
MAC address table size
512000 entries
Reliability
Availability
99.999%
Environment
Operating temperature 32°F to 113°F (0°C to 45°C)
Operating relative
10% to 95%, non-condensing
humidity
Nonoperating/Storage
-40°F to 158°F (-40°C to 70°C)
temperature
Nonoperating/Storage
5% to 95%, non-condensing
relative humidity
Acoustic
Low-speed fan: 51.6 dB, High-speed fan: 56.1 dB
Electrical characteristics Frequency
50/60 Hz
Voltage
100-120 / 200-240 VAC
Current
16/50 A
Power output
1400 W
Notes
Based on a common power supply of 1400 W (AC/DC)
Safety
UL 60950-1; IEC 60950-1; CAN/CSA-C22.2 No. 60950-1; EN 60950-1/A11
Emissions
VCCI Class A
EN 55022 Class A
ICES-003 Class A
ANSI C63.4 2003
AS/NZS CISPR 22 Class A
EN 61000-3-2:2006
EN 61000-3-3:1995 +A1:2001+A2:2005
EMC Directive 2004/108/EC
FCC (CFR 47, Part 15) Class A
Immunity
Generic
ETSI EN 300 386 V1.3.3
EN
EN 61000-4-2:1995+A1:1998+A2:2001
ESD
EN 61000-4-2
Radiated
EN 61000-4-3
EFT/Burst
EN 61000-4-4
Surge
EN 61000-4-5
c04111585 — DA – 13805 Worldwide — Version 35 — July 3, 2014
Page 37
QuickSpecs
HP 7500 Switch Series
Technical Specifications
Management
Notes
Services
Conducted
EN 61000-4-6
Power frequency
IEC 61000-4-8
magnetic field
Voltage dips and
EN 61000-4-11
interruptions
Harmonics
EN 61000-3-2, IEC 61000-3-2
Flicker
EN 61000-3-3, IEC 61000-3-3
IMC - Intelligent Management Center; command-line interface; Web browser; out-of-band
management (serial RS-232C); SNMP Manager; Telnet; terminal interface (serial RS-232C); modem
interface; IEEE 802.3 Ethernet MIB; Ethernet Interface MIB
For non-TAA environments, IPS/IDS functionality is provided by the HP S1200E IPS 7500 Module
(JC527A).
For non-TAA environments, IKE/IPSec functionality is provided by the HP 7500 VPN Firewall Module
(JD249A).
IRF functionality is not supported on HP 7502 and 7503-S Switch Chassis.
3-year, parts only, global next-day advance exchange (HP799E)
3-year, 4-hour onsite, 13x5 coverage for hardware (HP800E)
3-year, 4-hour onsite, 24x7 coverage for hardware (HP803E)
3-year, 4-hour onsite, 24x7 coverage for hardware, 24x7 software phone support (HP806E)
3-year, 24x7 SW phone support, software updates (HP809E)
Installation with minimum configuration, system-based pricing (UX032E)
4-year, 4-hour onsite, 13x5 coverage for hardware (HP801E)
4-year, 4-hour onsite, 24x7 coverage for hardware (HP804E)
4-year, 4-hour onsite, 24x7 coverage for hardware, 24x7 software phone (HP807E)
4-year, 24x7 SW phone support, software updates (HP810E)
5-year, 4-hour onsite, 13x5 coverage for hardware (HP802E)
5-year, 4-hour onsite, 24x7 coverage for hardware (HP805E)
5-year, 4-hour onsite, 24x7 coverage for hardware, 24x7 software phone (HP808E)
5-year, 24x7 SW phone support, software updates (HP811E)
3 Yr 6 hr Call-to-Repair Onsite (HP812E)
4 Yr 6 hr Call-to-Repair Onsite (HP813E)
5 Yr 6 hr Call-to-Repair Onsite (HP814E)
1-year, 4-hour onsite, 13x5 coverage for hardware (HR519E)
1-year, 4-hour onsite, 24x7 coverage for hardware (HR520E)
1-year, 6 hour Call-To-Repair Onsite for hardware (HR523E)
1-year, 24x7 software phone support, software updates (HR522E)
1-year, 4-hour onsite, 24x7 coverage for hardware, 24x7 software phone support and software
updates (HR521E)
Refer to the HP website at: www.hp.com/networking/services for details on the service-level
descriptions and product numbers. For details about services and response times in your area, please
contact your local HP sales office.
HP 7503-S Switch Chassis with 1 Fabric Slot (JD243B)
Included accessories
1 HP 7503-S Spare Fan Assembly (JC672A)
I/O ports and slots
2 I/O module slots
Supports a maximum of 16 10GbE ports or 120 autosensing 10/100/1000 ports or 120 SFP ports or 8
40GbE ports, or a combination
Additional ports and
1 switch fabric slot
slots
Power supplies
2 power-supply slots
1 minimum power-supply required (ordered separately)
c04111585 — DA – 13805 Worldwide — Version 35 — July 3, 2014
Page 38
QuickSpecs
HP 7500 Switch Series
Technical Specifications
Fan tray
Physical characteristics
includes: 1 x JC672A
1 fan tray slot
Dimensions
Weight
17.17(w) x 16.54(d) x 6.89(h) in (43.6 x 42.0 x 17.5 cm) (4U height)
59 lb (26.76 kg), Fully loaded chassis, one fabric, two power supplies, and a
full complement of typical I/O modules
Memory and processor
Fabric
MIPS64 @ 400 MHz, 64 MB flash, 512 MB RAM
I/O Module
MIPS64 @ 400 MHz, 512 MB RAM
Mounting
Mounts in an EIA-standard 19 in. rack or other equipment cabinet (hardware included); horizontal
surface mounting only
Performance
Throughput
107 million pps
Routing/Switching
144 Gb/s
capacity
Routing table size
256000 entries (IPv4), 8000 entries (IPv6)
MAC address table size
512000 entries
Reliability
Availability
99.999%
Environment
Operating temperature 32°F to 113°F (0°C to 45°C)
Operating relative
10% to 95%, non-condensing
humidity
Nonoperating/Storage
-40°F to 158°F (-40°C to 70°C)
temperature
Nonoperating/Storage
5% to 95%, non-condensing
relative humidity
Acoustic
High-speed fan: 56.7 dB
Electrical characteristics Frequency
50/60 Hz
AC Voltage
100-120 / 200-240 VAC
Current
5/10 A
Power output
300 W
Notes
Based on a common power supply of 300 W (AC/DC)
Safety
UL 60950-1; IEC 60950-1; CAN/CSA-C22.2 No. 60950-1; EN 60950-1/A11
Emissions
VCCI Class A
EN 55022 Class A
ICES-003 Class A
ANSI C63.4 2003
AS/NZS CISPR 22 Class A
EN 61000-3-2:2006
EN 61000-3-3:1995 +A1:2001+A2:2005
EMC Directive 2004/108/EC
FCC (CFR 47, Part 15) Class A
Immunity
Generic
ETSI EN 300 386 V1.3.3
EN
EN 61000-4-2:1995+A1:1998+A2:2001
ESD
EN 61000-4-2
Radiated
EN 61000-4-3
EFT/Burst
EN 61000-4-4
Surge
EN 61000-4-5
Conducted
EN 61000-4-6
Power frequency
IEC 61000-4-8
magnetic field
c04111585 — DA – 13805 Worldwide — Version 35 — July 3, 2014
Page 39
QuickSpecs
HP 7500 Switch Series
Technical Specifications
Management
Notes
Services
Voltage dips and
EN 61000-4-11
interruptions
Harmonics
EN 61000-3-2, IEC 61000-3-2
Flicker
EN 61000-3-3, IEC 61000-3-3
IMC - Intelligent Management Center; command-line interface; Web browser; out-of-band
management (serial RS-232C); SNMP Manager; Telnet; terminal interface (serial RS-232C); modem
interface; IEEE 802.3 Ethernet MIB; Ethernet Interface MIB
For non-TAA environments, IPS/IDS functionality is provided by the HP S1200E IPS 7500 Module
(JC527A).
For non-TAA environments, IKE/IPSec functionality is provided by the HP 7500 VPN Firewall Module
(JD249A).
IRF functionality is not supported on HP 7502 and 7503-S Switch Chassis.
3-year, parts only, global next-day advance exchange (HP799E)
3-year, 4-hour onsite, 13x5 coverage for hardware (HP800E)
3-year, 4-hour onsite, 24x7 coverage for hardware (HP803E)
3-year, 4-hour onsite, 24x7 coverage for hardware, 24x7 software phone support (HP806E)
3-year, 24x7 SW phone support, software updates (HP809E)
Installation with minimum configuration, system-based pricing (UX032E)
4-year, 4-hour onsite, 13x5 coverage for hardware (HP801E)
4-year, 4-hour onsite, 24x7 coverage for hardware (HP804E)
4-year, 4-hour onsite, 24x7 coverage for hardware, 24x7 software phone (HP807E)
4-year, 24x7 SW phone support, software updates (HP810E)
5-year, 4-hour onsite, 13x5 coverage for hardware (HP802E)
5-year, 4-hour onsite, 24x7 coverage for hardware (HP805E)
5-year, 4-hour onsite, 24x7 coverage for hardware, 24x7 software phone (HP808E)
5-year, 24x7 SW phone support, software updates (HP811E)
3 Yr 6 hr Call-to-Repair Onsite (HP812E)
4 Yr 6 hr Call-to-Repair Onsite (HP813E)
5 Yr 6 hr Call-to-Repair Onsite (HP814E)
1-year, 4-hour onsite, 13x5 coverage for hardware (HR519E)
1-year, 4-hour onsite, 24x7 coverage for hardware (HR520E)
1-year, 6 hour Call-To-Repair Onsite for hardware (HR523E)
1-year, 24x7 software phone support, software updates (HR522E)
1-year, 4-hour onsite, 24x7 coverage for hardware, 24x7 software phone support and software
updates (HR521E)
Refer to the HP website at: www.hp.com/networking/services for details on the service-level
descriptions and product numbers. For details about services and response times in your area, please
contact your local HP sales office.
HP 7502 Switch Chassis (JD242B)
Included accessories
1 HP 7502 Spare Fan Assembly (JD213A)
I/O ports and slots
2 I/O module slots
Supports a maximum of 16 10GbE ports or 96 autosensing 10/100/1000 ports or 96 SFP ports or 8
40GbE ports, or a combination
Additional ports and
2 MPU (for management modules) slots
slots
Power supplies
2 power-supply slots
1 minimum power-supply required (ordered separately)
Fan tray
includes: 1 x JD213A
1 fan tray slot
Physical characteristics Dimensions
17.17(w) x 16.54(d) x 6.89(h) in (43.6 x 42.0 x 17.5 cm) (4U height)
c04111585 — DA – 13805 Worldwide — Version 35 — July 3, 2014
Page 40
QuickSpecs
HP 7500 Switch Series
Technical Specifications
Weight
59 lb (26.76 kg), Fully loaded chassis, two management modules, two
power supplies, and a full complement of typical I/O modules
Memory and processor
Fabric
MIPS64 @ 600 MHz, 64 MB flash, 512 MB RAM
I/O Module
MIPS64 @ 400 MHz, 512 MB RAM
Mounting
Mounts in an EIA-standard 19 in. rack or other equipment cabinet (hardware included); horizontal
surface mounting only
Performance
Throughput
143 million pps
Routing/Switching
192 Gb/s
capacity
Routing table size
256000 entries (IPv4), 8000 entries (IPv6)
MAC address table size
512000 entries
Reliability
Availability
99.999%
Environment
Operating temperature 32°F to 113°F (0°C to 45°C)
Operating relative
10% to 95%, non-condensing
humidity
Nonoperating/Storage
-40°F to 158°F (-40°C to 70°C)
temperature
Nonoperating/Storage
5% to 95%, non-condensing
relative humidity
Acoustic
Low-speed fan: 49.8 dB, High-speed fan: 56.7 dB
Electrical characteristics Frequency
50/60 Hz
AC Voltage
100-120/200-240 VAC
Current
5/10 A
Power output
300 W
Notes
Based on a common power supply 300 W (AC/DC)
Safety
UL 60950-1; IEC 60950-1; CAN/CSA-C22.2 No. 60950-1; EN 60950-1/A11
Emissions
VCCI Class A
EN 55022 Class A
ICES-003 Class A
ANSI C63.4 2003
AS/NZS CISPR 22 Class A
EN 61000-3-2:2006
EN 61000-3-3:1995 +A1:2001+A2:2005
EMC Directive 2004/108/EC
FCC (CFR 47, Part 15) Class A
Immunity
Generic
ETSI EN 300 386 V1.3.3
EN
EN 61000-4-2:1995+A1:1998+A2:2001
ESD
EN 61000-4-2
Radiated
EN 61000-4-3
EFT/Burst
EN 61000-4-4
Surge
EN 61000-4-5
Conducted
EN 61000-4-6
Power frequency
IEC 61000-4-8
magnetic field
Voltage dips and
EN 61000-4-11
interruptions
Harmonics
EN 61000-3-2, IEC 61000-3-2
Flicker
EN 61000-3-3, IEC 61000-3-3
c04111585 — DA – 13805 Worldwide — Version 35 — July 3, 2014
Page 41
QuickSpecs
HP 7500 Switch Series
Technical Specifications
Management
Notes
Services
IMC - Intelligent Management Center; command-line interface; Web browser; out-of-band
management (serial RS-232C); SNMP Manager; Telnet; terminal interface (serial RS-232C); modem
interface; IEEE 802.3 Ethernet MIB; Ethernet Interface MIB
For non-TAA environments, IPS/IDS functionality is provided by the HP S1200E IPS 7500 Module
(JC527A).
For non-TAA environments, IKE/IPSec functionality is provided by the HP 7500 VPN Firewall Module
(JD249A).
IRF functionality is not supported on HP 7502 and 7503-S Switch Chassis.
3-year, parts only, global next-day advance exchange (HP799E)
3-year, 4-hour onsite, 13x5 coverage for hardware (HP800E)
3-year, 4-hour onsite, 24x7 coverage for hardware (HP803E)
3-year, 4-hour onsite, 24x7 coverage for hardware, 24x7 software phone support (HP806E)
3-year, 24x7 SW phone support, software updates (HP809E)
Installation with minimum configuration, system-based pricing (UX032E)
4-year, 4-hour onsite, 13x5 coverage for hardware (HP801E)
4-year, 4-hour onsite, 24x7 coverage for hardware (HP804E)
4-year, 4-hour onsite, 24x7 coverage for hardware, 24x7 software phone (HP807E)
4-year, 24x7 SW phone support, software updates (HP810E)
5-year, 4-hour onsite, 13x5 coverage for hardware (HP802E)
5-year, 4-hour onsite, 24x7 coverage for hardware (HP805E)
5-year, 4-hour onsite, 24x7 coverage for hardware, 24x7 software phone (HP808E)
5-year, 24x7 SW phone support, software updates (HP811E)
3 Yr 6 hr Call-to-Repair Onsite (HP812E)
4 Yr 6 hr Call-to-Repair Onsite (HP813E)
5 Yr 6 hr Call-to-Repair Onsite (HP814E)
1-year, 4-hour onsite, 13x5 coverage for hardware (HR519E)
1-year, 4-hour onsite, 24x7 coverage for hardware (HR520E)
1-year, 6 hour Call-To-Repair Onsite for hardware (HR523E)
1-year, 24x7 software phone support, software updates (HR522E)
1-year, 4-hour onsite, 24x7 coverage for hardware, 24x7 software phone support and software
updates (HR521E)
Refer to the HP website at: www.hp.com/networking/services for details on the service-level
descriptions and product numbers. For details about services and response times in your area, please
contact your local HP sales office.
HP 7503 Switch with 48-port Gig-T PoE+ Module and 384Gbps MPU with 2 XFP ports (JG507A)
Included accessories
1 HP 7503 Spare Fan Assembly (JD212A)
1 HP 7500 384Gbps Fabric Module with 2 XFP Ports (JD193B)
1 HP 7500 48-port Gig-T PoE+ Extended Module (JD229B)
I/O ports and slots
3 I/O module slots
Supports a maximum of 28 10GbE ports or 144 autosensing 10/100/1000 ports or 144 SFP ports, or a
combination
Additional ports and
2 switch fabric slots
slots
Power supplies
2 power-supply slots
1 minimum power-supply required (ordered separately)
Fan tray
includes: 1 x JD212A
1 fan tray slot
Physical characteristics Dimensions
17.17(w) x 16.54(d) x 17.36(h) in (43.6 x 42.0 x 44.1 cm) (10U height)
Weight
147 lb (66.68 kg), Fully loaded chassis, two fabrics, two power supplies,
and a full complement of typical I/O modules
c04111585 — DA – 13805 Worldwide — Version 35 — July 3, 2014
Page 42
QuickSpecs
HP 7500 Switch Series
Technical Specifications
Memory and processor
Fabric
MIPS64 @ 600 MHz, 64 MB flash, 512 MB RAM
I/O Module
MIPS64 @ 400 MHz, 512 MB RAM
Mounting
Mounts in an EIA-standard 19 in. rack or other equipment cabinet (hardware included); horizontal
surface mounting only
Performance
Throughput
274 million pps
Routing/Switching
480 Gb/s
capacity
Routing table size
256000 entries (IPv4), 8000 entries (IPv6)
MAC address table size
512000 entries
Reliability
Availability
99.999%
Environment
Operating temperature 32°F to 113°F (0°C to 45°C)
Operating relative
10% to 95%, non-condensing
humidity
Nonoperating/Storage
-40°F to 158°F (-40°C to 70°C)
temperature
Nonoperating/Storage
5% to 95%, non-condensing
relative humidity
Acoustic
Low-speed fan: 51.6 dB, High-speed fan: 56.1 dB
Electrical characteristics Frequency
50/60 Hz
AC Voltage
100-120/200-240 VAC
Current
16/50 A
Power output
1400 W
Notes
Based on a common power supply of 1400 W (AC/DC)
Safety
UL 60950-1; IEC 60950-1; CAN/CSA-C22.2 No. 60950-1; EN 60950-1/A11
Emissions
VCCI Class A
EN 55022 Class A
ICES-003 Class A
ANSI C63.4 2003
AS/NZS CISPR 22 Class A
EN 61000-3-2:2006
EN 61000-3-3:1995 +A1:2001+A2:2005
EMC Directive 2004/108/EC
FCC (CFR 47, Part 15) Class A
Immunity
Generic
ETSI EN 300 386 V1.3.3
EN
EN 61000-4-2:1995+A1:1998+A2:2001
ESD
EN 61000-4-2
Radiated
EN 61000-4-3
EFT/Burst
EN 61000-4-4
Surge
EN 61000-4-5
Conducted
EN 61000-4-6
Power frequency
IEC 61000-4-8
magnetic field
Voltage dips and
EN 61000-4-11
interruptions
Harmonics
EN 61000-3-2, IEC 61000-3-2
Flicker
EN 61000-3-3, IEC 61000-3-3
Management
IMC - Intelligent Management Center; command-line interface; Web browser; out-of-band
management
c04111585 — DA – 13805 Worldwide — Version 35 — July 3, 2014
Page 43
QuickSpecs
HP 7500 Switch Series
Technical Specifications
Notes
Services
(serial RS-232C); SNMP Manager; Telnet; terminal interface (serial RS-232C); modem interface; IEEE
802.3 Ethernet MIB; Ethernet Interface MIB
For non-TAA environments, IPS/IDS functionality is provided by the HP S1200E IPS 7500 Module
(JC527A).
For non-TAA environments, IKE/IPSec functionality is provided by the HP 7500 VPN Firewall Module
(JD249A).
IRF functionality is not supported on HP 7502 and 7503-S Switch Chassis.
Refer to the HP website at www.hp.com/networking/services for details on the service-level
descriptions and product numbers. For details about services and response times in your area, please
contact your local HP sales office.
HP 7506 Switch with 2 48-port Gig-T PoE+ Modules and 384Gbps MPU with 2 XFP ports (JG508A)
Included accessories
1 HP 7506 Spare Fan Assembly (JD214A)
2 HP 7500 48-port Gig-T PoE+ Extended Module (JD229B)
1 HP 7500 384Gbps Fabric Module with 2 XFP Ports (JD193B)
I/O ports and slots
6 I/O module slots
Supports a maximum of 52 10GbE ports or 288 autosensing 10/100/1000 ports or 288 SFP ports, or a
combination
Additional ports and
2 switch fabric slots
slots
Power supplies
2 power-supply slots
1 minimum power-supply required (ordered separately)
Fan tray
includes: 1 x JD214A
1 fan tray slot
Physical characteristics Dimensions
17.17(w) x 16.54(d) x 22.64(h) in (43.6 x 42.0 x 57.5 cm) (13U height)
Weight
207 lb (93.9 kg), Fully loaded chassis, two fabrics, two power supplies, and
a full complement of typical I/O modules
Memory and processor
Fabric
MIPS64 @ 600 MHz, 64 MB flash, 512 MB RAM
I/O Module
MIPS64 @ 400 MHz, 512 MB RAM
Mounting
Mounts in an EIA-standard 19 in. rack or other equipment cabinet (hardware included); horizontal
surface mounting only
Performance
Throughput
488 million pps
Routing/Switching
768 Gb/s
capacity
Routing table size
256000 entries (IPv4), 8000 entries (IPv6)
MAC address table size
512000 entries
Reliability
Availability
99.999%
Environment
Operating temperature 32°F to 113°F (0°C to 45°C)
Operating relative
10% to 95%, non-condensing
humidity
Nonoperating/Storage
-40°F to 158°F (-40°C to 70°C)
temperature
Nonoperating/Storage
5% to 95%, non-condensing
relative humidity
Acoustic
High-speed fan: 56.7 dB
Electrical characteristics Frequency
50/60 Hz
Achieved Miercom Certified Green Award
Description
The H3C S7506E (HP 7606) is Certified Green in the 2009 Miercom Green
Switches Industry Assessment.
c04111585 — DA – 13805 Worldwide — Version 35 — July 3, 2014
Page 44
QuickSpecs
HP 7500 Switch Series
Technical Specifications
Safety
Emissions
Immunity
Management
Notes
Services
Voltage
100-120/200-240 VAC
AC Current
16/50 A
Power output
1400 W
Notes
Based on a common power supply of 1400 W (AC/DC
UL 60950-1; IEC 60950-1; CAN/CSA-C22.2 No. 60950-1; EN 60950-1/A11
VCCI Class A
EN 55022 Class A
ICES-003 Class A
ANSI C63.4 2003
AS/NZS CISPR 22 Class A
EN 61000-3-2:2006
EN 61000-3-3:1995 +A1:2001+A2:2005
EMC Directive 2004/108/EC
FCC (CFR 47, Part 15) Class A
Generic
ETSI EN 300 386 V1.3.3
EN
EN 61000-4-2:1995+A1:1998+A2:2001
ESD
EN 61000-4-2
Radiated
EN 61000-4-3
EFT/Burst
EN 61000-4-4
Surge
EN 61000-4-5
Conducted
EN 61000-4-6
Power frequency
IEC 61000-4-8
magnetic field
Voltage dips and
EN 61000-4-11
interruptions
Harmonics
EN 61000-3-2, IEC 61000-3-2
Flicker
EN 61000-3-3, IEC 61000-3-3
IMC - Intelligent Management Center; command-line interface; Web browser; out-of-band
management (serial RS-232C); SNMP Manager; Telnet; terminal interface (serial RS-232C); modem
interface; IEEE 802.3 Ethernet MIB; Ethernet Interface MIB
For non-TAA environments, IPS/IDS functionality is provided by the HP S1200E IPS 7500 Module
(JC527A).
For non-TAA environments, IKE/IPSec functionality is provided by the HP 7500 VPN Firewall Module
(JD249A).
IRF functionality is not supported on HP 7502 and 7503-S Switch Chassis.
Refer to the HP website at: www.hp.com/networking/services for details on the service-level
descriptions and product numbers. For details about services and response times in your area, please
contact your local HP sales office.
HP 7510 Switch with 2 48-port Gig-T PoE+ Modules and 768Gbps MPU (JG509A)
Included accessories
2 HP 7500 48-port Gig-T PoE+ Extended Module (JD229B)
1 HP 7500 768Gbps Fabric Module (JD220A)
1 HP 7510 Spare Fan Assembly (JD216A)
I/O ports and slots
10 I/O module slots
Supports a maximum of 84 10GbE ports or 480 autosensing 10/100/1000 ports or 480 SFP ports, or a
combination
Additional ports and
2 switch fabric slots
slots
Power supplies
2 power-supply slots
c04111585 — DA – 13805 Worldwide — Version 35 — July 3, 2014
Page 45
QuickSpecs
HP 7500 Switch Series
Technical Specifications
1 minimum power-supply required (ordered separately)
Fan tray
includes: 1 x JD216A
1 fan tray slot
Physical characteristics Dimensions
17.17(w) x 16.54(d) x 27.87(h) in (43.6 x 42.0 x 70.8 cm) (16U height)
Weight
211 lb (95.71 kg), Fully loaded chassis, two fabrics, two power supplies,
and a full complement of typical I/O modules
Memory and processor
Fabric
MIPS64 @ 600 MHz, 64 MB flash, 512 MB RAM
I/O Module
MIPS64 @ 400 MHz, 512 MB RAM
Mounting
Mounts in an EIA-standard 19 in. rack or other equipment cabinet (hardware included); horizontal
surface mounting only
Performance
Throughput
714 million pps
Routing/Switching
1152 Gb/s
capacity
Routing table size
256000 entries (IPv4), 8000 entries (IPv6)
MAC address table size
512000 entries
Reliability
Availability
99.999%
Environment
Operating temperature 32°F to 113°F (0°C to 45°C)
Operating relative
10% to 95%, non-condensing
humidity
Nonoperating/Storage
-40°F to 158°F (-40°C to 70°C)
temperature
Nonoperating/Storage
5% to 95%, non-condensing
relative humidity
Acoustic
Low-speed fan: 53.5 dB, High-speed fan: 56.7 d
Electrical characteristics Frequency
50/60 Hz
AC Voltage
100-120/200-240 VAC
Current
16/50 A
Power output
1400 W
Notes
Based on a common power supply of 1400 W (AC/DC)
Safety
UL 60950-1; IEC 60950-1; CAN/CSA-C22.2 No. 60950-1; EN 60950-1/A11
Emissions
VCCI Class A
EN 55022 Class A
ICES-003 Class A
ANSI C63.4 2003
AS/NZS CISPR 22 Class A
EN 61000-3-2:2006
EN 61000-3-3:1995 +A1:2001+A2:2005
EMC Directive 2004/108/EC
FCC (CFR 47, Part 15) Class A
Immunity
Generic
ETSI EN 300 386 V1.3.3
EN
EN 61000-4-2:1995+A1:1998+A2:2001
ESD
EN 61000-4-2
Radiated
EN 61000-4-3
EFT/Burst
EN 61000-4-4
Surge
EN 61000-4-5
Conducted
EN 61000-4-6
Power frequency
IEC 61000-4-8
c04111585 — DA – 13805 Worldwide — Version 35 — July 3, 2014
Page 46
QuickSpecs
HP 7500 Switch Series
Technical Specifications
Management
Notes
Services
magnetic field
Voltage dips and
EN 61000-4-11
interruptions
Harmonics
EN 61000-3-2, IEC 61000-3-2
Flicker
EN 61000-3-3, IEC 61000-3-3
IMC - Intelligent Management Center; command-line interface; Web browser; out-of-band
management (serial RS-232C); SNMP Manager; Telnet; terminal interface (serial RS-232C); modem
interface; IEEE 802.3 Ethernet MIB; Ethernet Interface MIB
For non-TAA environments, IPS/IDS functionality is provided by the HP S1200E IPS 7500 Module
(JC527A).
For non-TAA environments, IKE/IPSec functionality is provided by the HP 7500 VPN Firewall Module
(JD249A).
IRF functionality is not supported on HP 7502 and 7503-S Switch Chassis.
Refer to the HP website at: www.hp.com/networking/services for details on the service-level
descriptions and product numbers. For details about services and response times in your area, please
contact your local HP sales office.
Standards and protocols BGP
(applies to all products in RFC 1771 BGPv4
series)
RFC 1772 Application of the BGP
RFC 1965 BGP4 confederations
RFC 1997 BGP Communities Attribute
RFC 1998 PPP Gandalf FZA Compression Protocol
RFC 2385 BGP Session Protection via TCP MD5
RFC 2439 BGP Route Flap Damping
RFC 2796 BGP Route Reflection
RFC 2858 BGP-4 Multi-Protocol Extensions
RFC 2918 Route Refresh Capability
RFC 3065 Autonomous System Confederations for
BGP
RFC 3392 Capabilities Advertisement with BGP-4
RFC 4271 A Border Gateway Protocol 4 (BGP-4)
RFC 4272 BGP Security Vulnerabilities Analysis
RFC 4273 Definitions of Managed Objects for
BGP-4
RFC 4274 BGP-4 Protocol Analysis
RFC 4275 BGP-4 MIB Implementation Survey
RFC 4276 BGP-4 Implementation Report
RFC 4277 Experience with the BGP-4 Protocol
RFC 4360 BGP Extended Communities Attribute
RFC 4456 BGP Route Reflection: An Alternative to
Full Mesh Internal BGP (IBGP)
RFC 5291 Outbound Route Filtering Capability for
BGP-4
RFC 5292 Address-Prefix-Based Outbound Route
Filter for BGP-4
Denial of service protection
RFC 2267 Network Ingress Filtering
Automatic filtering of well-known denial-ofservice
packets
CPU DoS Protection
Rate Limiting by ACLs
MIBs
RFC 1156 (TCP/IP MIB)
RFC 1157 A Simple Network Management Protocol
(SNMP)
RFC 1215 A Convention for Defining Traps for use
with the SNMP
RFC 1229 Interface MIB Extensions
RFC 1493 Bridge MIB
RFC 1573 SNMP MIB II
RFC 1643 Ethernet MIB
RFC 1657 BGP-4 MIB
RFC 1724 RIPv2 MIB
RFC 1757 Remote Network Monitoring MIB
RFC 1850 OSPFv2 MIB
RFC 1907 SNMPv2 MIB
RFC 2011 SNMPv2 MIB for IP
RFC 2012 SNMPv2 MIB for TCP
RFC 2013 SNMPv2 MIB for UDP
RFC 2096 IP Forwarding Table MIB
RFC 2233 Interfaces MIB
RFC 2452 IPV6-TCP-MIB
RFC 2454 IPV6-UDP-MIB
RFC 2465 IPv6 MIB
RFC 2466 ICMPv6 MIB
RFC 2571 SNMP Framework MIB
RFC 2572 SNMP-MPD MIB
RFC 2573 SNMP-Notification MIB
RFC 2573 SNMP-Target MIB
RFC 2578 Structure of Management Information
Version 2 (SMIv2)
RFC 2580 Conformance Statements for SMIv2
RFC 2618 RADIUS Client MIB
RFC 2620 RADIUS Accounting MIB
RFC 2665 Ethernet-Like-MIB
RFC 2668 802.3 MAU MIB
RFC 2674 802.1p and IEEE 802.1Q Bridge MIB
RFC 2787 VRRP MIB
RFC 2819 RMON MIB
c04111585 — DA – 13805 Worldwide — Version 35 — July 3, 2014
Page 47
QuickSpecs
HP 7500 Switch Series
Technical Specifications
Device management
RFC 1157 SNMPv1/v2c
RFC 1305 NTPv3
RFC 1902 (SNMPv2)
RFC 2271 FrameWork
RFC 2579 (SMIv2 Text Conventions)
RFC 2580 (SMIv2 Conformance)
RFC 2819 (RMON groups Alarm, Event, History
and Statistics only)
HTTP, SSHv1, and Telnet
Multiple Configuration Files
Multiple Software Images
SSHv1/SSHv2 Secure Shell
TACACS/TACACS+
Web UI
General protocols
IEEE 802.1ad Q-in-Q
IEEE 802.1ag Service Layer OAM
IEEE 802.1p Priority
IEEE 802.1Q VLANs
IEEE 802.1s Multiple Spanning Trees
IEEE 802.1w Rapid Reconfiguration of Spanning
Tree
IEEE 802.1X PAE
IEEE 802.3ab 1000BASE-T
IEEE 802.3ac (VLAN Tagging Extension)
IEEE 802.3ad Link Aggregation Control Protocol
(LACP)
IEEE 802.3ae 10-Gigabit Ethernet
IEEE 802.3af Power over Ethernet
IEEE 802.3ah Ethernet in First Mile over Point to
Point Fiber - EFMF
IEEE 802.3at
IEEE 802.3ba 40 and 100 Gigabit Ethernet
Architecture
IEEE 802.3u 100BASE-X
IEEE 802.3x Flow Control
IEEE 802.3z 1000BASE-X
RFC 768 UDP
RFC 783 TFTP Protocol (revision 2)
RFC 791 IP
RFC 792 ICMP
RFC 793 TCP
RFC 826 ARP
RFC 854 TELNET
RFC 894 IP over Ethernet
RFC 903 RARP
RFC 906 TFTP Bootstrap
RFC 925 Multi-LAN Address Resolution
RFC 950 Internet Standard Subnetting Procedure
RFC 951 BOOTP
RFC 959 File Transfer Protocol (FTP)
RFC 1027 Proxy ARP
RFC 1035 Domain Implementation and
Specification
RFC 2925 Ping MIB
RFC 2933 IGMP MIB
RFC 2934 Protocol Independent Multicast MIB for
IPv4
RFC 3414 SNMP-User based-SM MIB
RFC 3415 SNMP-View based-ACM MIB
RFC 3417 Simple Network Management Protocol
(SNMP) over IEEE 802 Networks
RFC 3418 MIB for SNMPv3
RFC 3595 Textual Conventions for IPv6 Flow Label
RFC 3621 Power Ethernet MIB
RFC 3813 MPLS LSR MIB
RFC 3814 MPLS FTN MIB
RFC 3815 MPLS LDP MIB
RFC 3826 AES for SNMP's USM MIB
RFC 4133 Entity MIB (Version 3)
RFC 4444 Management Information Base for
Intermediate System to Intermediate System (ISIS)
MPLS
RFC 2205 Resource ReSerVation Protocol
RFC 2209 Resource ReSerVation Protocol (RSVP)
RFC 2702 Requirements for Traffic Engineering
Over MPLS
RFC 2858 Multiprotocol Extensions for BGP-4
RFC 2961 RSVP Refresh Overhead Reduction
Extensions
RFC 3031 Multiprotocol Label Switching
Architecture
RFC 3032 MPLS Label Stack Encoding
RFC 3107 Carrying Label Information in BGP-4
RFC 3209 RSVP-TE: Extensions to RSVP for LSP
Tunnels
RFC 3212 Constraint-Based LSP Setup using LDP
RFC 3479 Fault Tolerance for the Label
Distribution
Protocol (LDP)
RFC 3487 Graceful Restart Mechanism for LDP
RFC 3564 Requirements for Support of
Differentiated Service-aware MPLS Traffic
Engineering
RFC 4364 BGP/MPLS IP Virtual Private Networks
(VPNs)
RFC 4379 Detecting Multi-Protocol Label Switched
(MPLS) Data Plane Failures
RFC 4447 Pseudowire Setup and Maintenance
Using LDP
RFC 4448 Encapsulation Methods for Transport of
Ethernet over MPLS Networks
RFC 4664 Framework for Layer 2 Virtual Private
Networks
RFC 4665 Service Requirements for Layer 2
Provider Provisioned Virtual Private Networks
RFC 4761 Virtual Private LAN Service (VPLS) Using
BGP for Auto-Discovery and Signaling
c04111585 — DA – 13805 Worldwide — Version 35 — July 3, 2014
Page 48
QuickSpecs
HP 7500 Switch Series
Technical Specifications
RFC 1042 IP Datagrams
RFC 1058 RIPv1
RFC 1142 OSI IS-IS Intra-domain Routing Protocol
RFC 1195 OSI ISIS for IP and Dual Environments
RFC 1213 Management Information Base for
Network Management of TCP/IP-based internets
RFC 1256 ICMP Router Discovery Protocol (IRDP)
RFC 1293 Inverse Address Resolution Protocol
RFC 1305 NTPv3
RFC 1350 TFTP Protocol (revision 2)
RFC 1393 Traceroute Using an IP Option
RFC 1519 CIDR
RFC 1531 Dynamic Host Configuration Protocol
RFC 1533 DHCP Options and BOOTP Vendor
Extensions
RFC 1591 DNS (client only)
RFC 1624 Incremental Internet Checksum
RFC 1701 Generic Routing Encapsulation
RFC 1721 RIP-2 Analysis
RFC 1723 RIP v2
RFC 1812 IPv4 Routing
RFC 2030 Simple Network Time Protocol (SNTP) v4
RFC 2082 RIP-2 MD5 Authentication
RFC 2091 Trigger RIP
RFC 2131 DHCP
RFC 2138 Remote Authentication Dial In User
Service (RADIUS)
RFC 2236 IGMP Snooping
RFC 2338 VRRP
RFC 2453 RIPv2
RFC 2644 Directed Broadcast Control
RFC 2763 Dynamic Name-to-System ID mapping
support
RFC 2784 Generic Routing Encapsulation (GRE)
RFC 2865 Remote Authentication Dial In User
Service (RADIUS)
RFC 2966 Domain-wide Prefix Distribution with
Two-Level IS-IS
RFC 2973 IS-IS Mesh Groups
RFC 3022 Traditional IP Network Address
Translator (Traditional NAT)
RFC 3277 IS-IS Transient Blackhole Avoidance
RFC 3567 Intermediate System to Intermediate
System (IS-IS) Cryptographic Authentication
RFC 3719 Recommendations for Interoperable
Networks using Intermediate System to
Intermediate System (IS-IS)
RFC 3784 ISIS TE support
RFC 3786 Extending the Number of IS-IS LSP
Fragments Beyond the 256 Limit
RFC 3787 Recommendations for Interoperable IP
Networks using Intermediate System to
Intermediate System (IS-IS)
RFC 3847 Restart signaling for IS-IS
RFC 4251 The Secure Shell (SSH) Protocol
Architecture
RFC 4762 Virtual Private LAN Service (VPLS) Using
Label Distribution Protocol (LDP) Signaling
RFC 5036 LDP Specification
Network management
IEEE 802.1AB Link Layer Discovery Protocol (LLDP)
RFC 1155 Structure of Management Information
RFC 1157 SNMPv1
RFC 1448 Protocol Operations for version 2 of the
Simple Network Management Protocol (SNMPv2)
RFC 2211 Controlled-Load Network
RFC 2819 Four groups of RMON: 1 (statistics), 2
(history), 3 (alarm) and 9 (events)
RFC 3176 sFlow
RFC 3411 SNMP Management Frameworks
RFC 3412 SNMPv3 Message Processing
RFC 3414 SNMPv3 User-based Security Model
(USM)
RFC 3415 SNMPv3 View-based Access Control
Model VACM)
ANSI/TIA-1057 LLDP Media Endpoint Discovery
(LLDP-MED)
OSPF
RFC 1245 OSPF protocol analysis
RFC 1246 Experience with OSPF
RFC 1765 OSPF Database Overflow
RFC 1850 OSPFv2 Management Information Base
(MIB), traps
RFC 2154 OSPF w/ Digital Signatures (Password,
MD-5)
RFC 2328 OSPFv2
RFC 2370 OSPF Opaque LSA Option
RFC 3101 OSPF NSSA
RFC 3137 OSPF Stub Router Advertisement
RFC 3623 Graceful OSPF Restart
RFC 3630 Traffic Engineering Extensions to
OSPFv2
RFC 4061 Benchmarking Basic OSPF Single Router
Control Plane Convergence
RFC 4062 OSPF Benchmarking Terminology and
Concepts
RFC 4063 Considerations When Using Basic OSPF
Convergence Benchmarks
RFC 4222 Prioritized Treatment of Specific OSPF
Version 2 Packets and Congestion Avoidance
RFC 4577 OSPF as the Provider/Customer Edge
Protocol for BGP/MPLS IP Virtual Private Networks
(VPNs)
RFC 4811 OSPF Out-of-Band LSDB
Resynchronization
RFC 4812 OSPF Restart Signaling
RFC 4813 OSPF Link-Local Signaling
RFC 4940 IANA Considerations for OSPF
QoS/CoS
c04111585 — DA – 13805 Worldwide — Version 35 — July 3, 2014
Page 49
QuickSpecs
HP 7500 Switch Series
Technical Specifications
RFC 4486 Subcodes for BGP Cease Notification
Message
RFC 4884 Extended ICMP to Support Multi-Part
Messages
RFC 4941 Privacy Extensions for Stateless Address
Autoconfiguration in IPv6
RFC 5130 A Policy Control Mechanism in IS-IS
Using Administrative Tags
IP multicast
RFC 2236 IGMPv2
RFC 2283 Multiprotocol Extensions for BGP-4
RFC 2362 PIM Sparse Mode
RFC 3376 IGMPv3
RFC 3446 Anycast Rendezvous Point (RP)
mechanism using Protocol Independent Multicast
(PIM) and Multicast Source Discovery Protocol
(MSDP)
RFC 3618 Multicast Source Discovery Protocol
(MSDP)
RFC 3973 PIM Dense Mode
RFC 4541 Considerations for Internet Group
Management Protocol (IGMP) and Multicast
Listener
Discovery (MLD) Snooping Switches
RFC 4601 Draft 10 PIM Sparse Mode
RFC 4604 Using Internet Group Management
Protocol Version 3 (IGMPv3) and Multicast Listener
Discovery Protocol Version 2 (MLDv2) for
Source-Specific Multicast
RFC 4605 IGMP/MLD Proxying
RFC 4607 Source-Specific Multicast for IP
RFC 4610 Anycast-RP Using Protocol Independent
Multicast (PIM)
RFC 5059 Bootstrap Router (BSR) Mechanism for
Protocol Independent Multicast (PIM)
IPv6
RFC 1886 DNS Extension for IPv6
RFC 1887 IPv6 Unicast Address Allocation
Architecture
RFC 1981 IPv6 Path MTU Discovery
RFC 2080 RIPng for IPv6
RFC 2081 RIPng Protocol Applicability Statement
RFC 2292 Advanced Sockets API for IPv6
RFC 2373 IPv6 Addressing Architecture
RFC 2375 IPv6 Multicast Address Assignments
RFC 2460 IPv6 Specification
RFC 2461 IPv6 Neighbor Discovery
RFC 2462 IPv6 Stateless Address Autoconfiguration
RFC 2463 ICMPv6
RFC 2464 Transmission of IPv6 over Ethernet
Networks
RFC 2473 Generic Packet Tunneling in IPv6
RFC 2526 Reserved IPv6 Subnet Anycast
IEEE 802.1P (CoS)
RFC 1349 Type of Service in the Internet Protocol
Suite
RFC 2211 Specification of the Controlled-Load
Network Element Service
RFC 2212 Guaranteed Quality of Service
RFC 2474 DSCP DiffServ
RFC 2475 DiffServ Architecture
RFC 2597 DiffServ Assured Forwarding (AF)
RFC 2598 DiffServ Expedited Forwarding (EF)
Security
IEEE 802.1X Port Based Network Access Control
RFC 1321 The MD5 Message-Digest Algorithm
RFC 1334 PPP Authentication Protocols (PAP)
RFC 1492 TACACS+
RFC 1994 PPP Challenge Handshake
Authentication
Protocol (CHAP)
RFC 2082 RIP-2 MD5 Authentication
RFC 2104 Keyed-Hashing for Message
Authentication
RFC 2408 Internet Security Association and Key
Management Protocol (ISAKMP)
RFC 2409 The Internet Key Exchange (IKE)
RFC 2716 PPP EAP TLS Authentication Protocol
RFC 2865 RADIUS Authentication
RFC 2866 RADIUS Accounting
RFC 2867 RADIUS Accounting Modifications for
Tunnel Protocol Support
RFC 2868 RADIUS Attributes for Tunnel Protocol
Support
RFC 2869 RADIUS Extensions
Access Control Lists (ACLs)
Guest VLAN for 802.1x
MAC Authentication
Port Security
SSHv1/SSHv2 Secure Shell
VPN
RFC 2403 - HMAC-MD5-96
RFC 2404 - HMAC-SHA1-96
RFC 2405 - DES-CBC Cipher algorithm
RFC 2407 - Domain of interpretation
RFC 2547 BGP/MPLS VPNs
RFC 2917 A Core MPLS IP VPN Architecture
RFC 3947 - Negotiation of NAT-Traversal in the IKE
RFC 4302 - IP Authentication Header (AH)
RFC 4303 - IP Encapsulating Security Payload
(ESP)
IPsec
RFC 1828 IP Authentication using Keyed MD5
RFC 1829 The ESP DES-CBC Transform
RFC 2085 HMAC-MD5 IP Authentication with
Replay Prevention
c04111585 — DA – 13805 Worldwide — Version 35 — July 3, 2014
Page 50
QuickSpecs
HP 7500 Switch Series
Technical Specifications
Addresses
RFC 2529 Transmission of IPv6 Packets over IPv4
RFC 2545 Use of MP-BGP-4 for IPv6
RFC 2553 Basic Socket Interface Extensions for
IPv6
RFC 2710 Multicast Listener Discovery (MLD) for
IPv6
RFC 2740 OSPFv3 for IPv6
RFC 2767 Dual stacks IPv46 & IPv6
RFC 2893 Transition Mechanisms for IPv6 Hosts
and Routers
RFC 3056 Connection of IPv6 Domains via IPv4
Clouds
RFC 3307 IPv6 Multicast Address Allocation
RFC 3315 DHCPv6 (client and relay)
RFC 3484 Default Address Selection for IPv6
RFC 3513 IPv6 Addressing Architecture
RFC 3736 Stateless Dynamic Host Configuration
Protocol (DHCP) Service for IPv6
RFC 3810 MLDv2 for IPv6
RFC 4214 Intra-Site Automatic Tunnel Addressing
Protocol (ISATAP)
RFC 4861 IPv6 Neighbor Discovery
RFC 4862 IPv6 Stateless Address Autoconfiguration
RFC 2401 IP Security Architecture
RFC 2402 IP Authentication Header
RFC 2406 IP Encapsulating Security Payload
RFC 2410 - The NULL Encryption Algorithm and its
use with IPsec
RFC 2411 IP Security Document Roadmap
c04111585 — DA – 13805 Worldwide — Version 35 — July 3, 2014
Page 51
QuickSpecs
HP 7500 Switch Series
Accessory Product Details
NOTE: Details are not available for all accessories. The following specifications were available at the time of publication.
HP 7500 48-port
100BASE-FX Module
(JD197B)
Ports
Physical characteristics
Services
HP 7500 48-port
10/100BASE-T Module
(JD198B)
Ports
Physical characteristics
Services
HP 7500 48-port Gig-T
PoE-ready Module
(JD199B)
Ports
Physical characteristics
Services
HP 7500 2-port 10GbE
XFP Module (JD201A)
Ports
Physical characteristics
Services
HP 7500 24-port GbE SFP Ports
Module (JD203B)
Physical characteristics
Services
48 SFP 100BASE-FX ports (IEEE 802.3u Type 100BASE-FX); Duplex: full
only
Dimensions
13.98(d) x 14.84(w) x 1.57(h) in.
(35.5 x 37.7 x 4 cm)
Weight
6.72 lb. (3.05 kg)
Refer to the HP website at www.hp.com/networking/services for details on
the service-level descriptions and product numbers. For details about
services and response times in your area, please contact your local HP
sales office.
48 RJ-45 autosensing 10/100 PoE ports (IEEE 802.3 Type 10BASE-T, IEEE
802.3u Type 100BASE-TX, IEEE 802.3af PoE); Duplex: half or full
Dimensions
13.98(d) x 14.84(w) x 1.57(h) in.
(35.5 x 37.7 x 4 cm)
Weight
6.37 lb. (2.89 kg)
Refer to the HP website at www.hp.com/networking/services for details on
the service-level descriptions and product numbers. For details about
services and response times in your area, please contact your local HP
sales office.
48 RJ-45 autosensing 10/100/1000 PoE ports (IEEE 802.3 Type 10BASE-T,
IEEE 802.3u Type 100BASE-TX, IEEE 802.3ab Type 1000BASE-T, IEEE
802.3af PoE); Duplex: 10BASE-T/100BASE-TX: half or full; 1000BASE-T: full
only
Dimensions
13.98(d) x 14.84(w) x 1.57(h) in.
(35.5 x 37.7 x 4 cm)
Weight
6.81 lb. (3.09 kg)
Refer to the HP website at www.hp.com/networking/services for details on
the service-level descriptions and product numbers. For details about
services and response times in your area, please contact your local HP
sales office.
2 XFP 10-GbE ports; Duplex: full only
Dimensions
13.98(d) x 14.84(w) x 1.57(h) in.
(35.5 x 37.7 x 4 cm)
Weight
6.5 lb. (2.95 kg)
Refer to the HP website at www.hp.com/networking/services for details on
the service-level descriptions and product numbers. For details about
services and response times in your area, please contact your local HP
sales office.
24 SFP 100/1000 Mbps ports
Dimensions
13.98(d) x 14.84(w) x 1.57(h) in.
(35.5 x 37.7 x 4 cm)
Weight
6.13 lb. (2.78 kg)
Refer to the HP website at www.hp.com/networking/services for details on
the service-level descriptions and product numbers. For details about
services and response times in your area, please contact your local HP
c04111585 — DA – 13805 Worldwide — Version 35 — July 3, 2014
Page 52
QuickSpecs
HP 7500 Switch Series
Accessory Product Details
sales office.
HP 7500 24-port Gig-T
Module (JD204B)
Ports
Physical characteristics
Services
HP 7500 24-port GbE SFP Ports
/ 2-port 10GbE XFP
Module (JD205A)
Physical characteristics
Services
HP 7500 12-port GbE SFP Ports
Module (JD207A)
Physical characteristics
Services
HP 7500 24-port Gig-T / Ports
2-port 10GbE XFP Module
(JD206A)
Physical characteristics
Services
HP 7500 48-port Gig-T
Module (JD210A)
Ports
Physical characteristics
24 RJ-45 autosensing 10/100/1000 ports (IEEE 802.3 Type 10BASE-T, IEEE
802.3u Type 100BASE-TX, IEEE 802.3ab Type 1000BASE-T); Duplex:
10BASE-T/100BASE-TX: half or full; 1000BASE-T: full only
Dimensions
13.98(d) x 14.84(w) x 1.57(h) in.
(35.5 x 37.7 x 4 cm)
Weight
6 lb. (2.72 kg)
Refer to the HP website at www.hp.com/networking/services for details on
the service-level descriptions and product numbers. For details about
services and response times in your area, please contact your local HP
sales office.
24 SFP 100/1000 Mbps ports
2 XFP 10-GbE ports; Duplex: full only
Dimensions
13.98(d) x 14.84(w) x 1.57(h) in.
(35.5 x 37.7 x 4 cm)
Weight
6.5 lb. (2.95 kg)
Refer to the HP website at www.hp.com/networking/services for details on
the service-level descriptions and product numbers. For details about
services and response times in your area, please contact your local HP
sales office.
12 SFP 100/1000 Mbps ports
Dimensions
13.98(d) x 1.18(w) x 1.57(h) in.
(35.5 x 3 x 4 cm)
Weight
5.86 lb. (2.66 kg)
Refer to the HP website at www.hp.com/networking/services for details on
the service-level descriptions and product numbers. For details about
services and response times in your area, please contact your local HP
sales office.
24 RJ-45 autosensing 10/100/1000 ports (IEEE 802.3 Type 10BASE-T, IEEE
802.3u Type 100BASE-TX, IEEE 802.3ab Type 1000BASE-T); Duplex:
10BASE-T/100BASE-TX: half or full; 1000BASE-T: full only
2 XFP 10-GbE ports; Duplex: full only
Dimensions
13.98(d) x 14.84(w) x 1.57(h) in.
(35.5 x 37.7 x 4 cm)
Weight
6.44 lb. (2.92 kg)
Refer to the HP website at www.hp.com/networking/services for details on
the service-level descriptions and product numbers. For details about
services and response times in your area, please contact your local HP
sales office.
48 RJ-45 autosensing 10/100/1000 PoE ports (IEEE 802.3 Type 10BASE-T,
IEEE 802.3u Type 100BASE-TX, IEEE 802.3ab Type 1000BASE-T, IEEE
802.3af PoE); Duplex: 10BASE-T/100BASE-TX: half or full; 1000BASE-T: full
only
Dimensions
13.98(d) x 14.84(w) x 1.57(h) in.
(35.5 x 37.7 x 4 cm)
Weight
6.81 lb. (3.09 kg)
c04111585 — DA – 13805 Worldwide — Version 35 — July 3, 2014
Page 53
QuickSpecs
HP 7500 Switch Series
Accessory Product Details
Services
HP 7500 48-port GbE SFP Ports
Module (JD211B)
Physical characteristics
Services
HP 7500 24-port GbE SFP Ports
Module with 8 Combo
Ports (JD223A)
Physical characteristics
Services
HP 7500 40-port Gig-T /
8-port SFP PoE-ready
Module (JD228B)
Ports
Physical characteristics
Services
HP 7500 8-port 10G SFP+ Ports
Module (JF290A)
Physical characteristics
Notes
Services
HP 7500 20-port Gig-T /
4-port GbE Combo PoEupgradable SC Module
Ports
Refer to the HP website at www.hp.com/networking/services for details on
the service-level descriptions and product numbers. For details about
services and response times in your area, please contact your local HP
sales office.
48 SFP 100/1000 Mbps ports
Dimensions
13.98(d) x 14.84(w) x 1.57(h) in.
(35.5 x 37.7 x 4 cm)
Weight
6.7 lb. (3.04 kg)
Refer to the HP website at www.hp.com/networking/services for details on
the service-level descriptions and product numbers. For details about
services and response times in your area, please contact your local HP
sales office.
16 SFP 100/1000 Mbps ports
8 dual-personality ports; 1000M Combo ports (SFP or RJ-45)
Dimensions
13.98(d) x 14.84(w) x 1.57(h) in.
(35.5 x 37.7 x 4 cm)
Weight
6.11 lb. (2.77 kg)
Refer to the HP website at www.hp.com/networking/services for details on
the service-level descriptions and product numbers. For details about
services and response times in your area, please contact your local HP
sales office.
40 RJ-45 autosensing 10/100/1000 PoE ports (IEEE 802.3 Type 10BASE-T,
IEEE 802.3u Type 100BASE-TX, IEEE 802.3ab Type 1000BASE-T, IEEE
802.3af PoE); Duplex: 10BASE-T/100BASE-TX: half or full; 1000BASE-T: full
only
8 SFP 100/1000 Mbps ports
Dimensions
13.98(d) x 14.84(w) x 1.57(h) in.
(35.5 x 37.7 x 4 cm)
Weight
6.66 lb. (3.02 kg)
Refer to the HP website at www.hp.com/networking/services for details on
the service-level descriptions and product numbers. For details about
services and response times in your area, please contact your local HP
sales office.
8 SFP+ 10-GbE ports; Duplex: full only
Dimensions
13.98(d) x 14.84(w) x 1.57(h) in.
(35.5 x 37.7 x 4 cm)
Weight
6.97 lb. (3.16 kg)
The module (JF290A) only support 10-GbE SFP+ transceiver, not support
1GbE SFP transceiver.
Refer to the HP website at www.hp.com/networking/services for details on
the service-level descriptions and product numbers. For details about
services and response times in your area, please contact your local HP
sales office.
20 RJ-45 auto-negotiating 10/100/1000 PoE ports (IEEE 802.3 Type
10BASE-T, IEEE 802.3u Type 100BASE-TX, IEEE 802.3ab Type 1000BASE-T,
IEEE 802.3af PoE); Duplex: 10BASE-T/100BASE-TX: half or full; 1000BASE-
c04111585 — DA – 13805 Worldwide — Version 35 — July 3, 2014
Page 54
QuickSpecs
HP 7500 Switch Series
Accessory Product Details
(JC669A)
Physical characteristics
Services
HP 7500 8-port 10GbE
XFP Extended Module
(JD191A)
Ports
Physical characteristics
Services
HP 7500 48-port Gig-T
PoE+ Extended Module
(JD229B)
Ports
Physical characteristics
Services
HP 7500 24-port GbE SFP Ports
/ 2-port 10GbE XFP
Extended Module
(JD230A)
Physical characteristics
Services
HP 7500 24-port GbE SFP Ports
Extended Module
(JD234A)
Physical characteristics
Services
T: full only
4 dual-personality ports; Each composed of a 10/100/1000Base-T Gigabit
Ethernet port and an SFP port, which cannot be simultaneously used
Dimensions
13.98(d) x 14.84(w) x 1.57(h) in. (35.5 x 37.7 x 4
cm)
Weight
6.17 lb. (2.8 kg)
Refer to the HP website at: www.hp.com/networking/services for details
on the service-level descriptions and product numbers. For details about
services and response times in your area, please contact your local HP
sales office.
8 XFP 10-GbE ports; Duplex: full only
Dimensions
13.98(d) x 14.84(w) x 1.57(h) in.
(35.5 x 37.7 x 4 cm)
Weight
7.12 lb. (3.23 kg)
Refer to the HP website at www.hp.com/networking/services for details on
the service-level descriptions and product numbers. For details about
services and response times in your area, please contact your local HP
sales office.
48 RJ-45 autosensing 10/100/1000 PoE+ ports (IEEE 802.3 Type 10BASET, IEEE 802.3u Type 100BASE-TX, IEEE 802.3ab Type 1000BASE-T, IEEE
802.3at PoE+); Duplex: 10BASE-T/100BASE-TX: half or full; 1000BASE-T:
full only
Dimensions
13.98(d) x 14.84(w) x 1.57(h) in.
(35.5 x 37.7 x 4 cm)
Weight
7.3 lb. (3.31 kg)
Refer to the HP website at www.hp.com/networking/services for details on
the service-level descriptions and product numbers. For details about
services and response times in your area, please contact your local HP
sales office.
16 SFP 1000 Mbps ports
8 dual-personality ports; 1000M Combo ports (SFP or RJ-45)
2 XFP 10-GbE ports; Duplex: full only
Dimensions
13.98(d) x 14.84(w) x 1.57(h) in.
(35.5 x 37.7 x 4 cm)
Weight
6.79 lb. (3.08 kg)
Refer to the HP website at www.hp.com/networking/services for details on
the service-level descriptions and product numbers. For details about
services and response times in your area, please contact your local HP
sales office.
16 SFP 100/1000 Mbps ports
8 dual-personality ports; 1000M Combo ports (SFP or RJ-45)
Dimensions
13.98(d) x 14.84(w) x 1.57(h) in.
(35.5 x 37.7 x 4 cm)
Weight
6.64 lb. (3.01 kg)
Refer to the HP website at www.hp.com/networking/services for details on
the service-level descriptions and product numbers. For details about
services and response times in your area, please contact your local HP
c04111585 — DA – 13805 Worldwide — Version 35 — July 3, 2014
Page 55
QuickSpecs
HP 7500 Switch Series
Accessory Product Details
sales office.
HP 7500 4-port 10GbE
XFP Extended Module
(JD235A)
Ports
Physical characteristics
Services
HP 7500 2-port 10GbE
XFP Extended Module
(JD236A)
Ports
Physical characteristics
Services
HP 7500 48-port GbE SFP Ports
Extended Module
Physical characteristics
(JD237A)
Services
HP 7500 48-port GbE SFP Ports
Enhanced Module
Physical characteristics
(JD221A)
Services
HP 7500 24-port GbE SFP Ports
Enhanced Module
(JD231A)
Physical characteristics
Services
HP 7500 24-port GbE SFP Ports
Enhanced Module
4 XFP 10-GbE ports; Duplex: full only
Dimensions
13.98(d) x 14.84(w) x 1.57(h) in.
(35.5 x 37.7 x 4 cm)
Weight
6.46 lb. (2.93 kg)
Refer to the HP website at www.hp.com/networking/services for details on
the service-level descriptions and product numbers. For details about
services and response times in your area, please contact your local HP
sales office.
2 XFP 10-GbE ports; Duplex: full only
Dimensions
13.98(d) x 14.84(w) x 1.57(h) in.
(35.5 x 37.7 x 4 cm)
Weight
6.46 lb. (2.93 kg)
Refer to the HP website at www.hp.com/networking/services for details on
the service-level descriptions and product numbers. For details about
services and response times in your area, please contact your local HP
sales office.
48 SFP 100/1000 Mbps ports
Dimensions
13.98(d) x 14.84(w) x 1.57(h) in.
(35.5 x 37.7 x 4 cm)
Weight
7.16 lb. (3.25 kg)
Refer to the HP website at www.hp.com/networking/services for details on
the service-level descriptions and product numbers. For details about
services and response times in your area, please contact your local HP
sales office.
48 SFP 100/1000 Mbps ports
Dimensions
13.98(d) x 14.84(w) x 1.57(h) in.
(35.5 x 37.7 x 4 cm)
Weight
7.16 lb. (3.25 kg)
Refer to the HP website at www.hp.com/networking/services for details on
the service-level descriptions and product numbers. For details about
services and response times in your area, please contact your local HP
sales office.
16 XFP 100/1000 Mbps ports
8 dual-personality ports; 1000M Combo ports (SFP or RJ-45)
Dimensions
13.98(d) x 14.84(w) x 1.57(h) in.
(35.5 x 37.7 x 4 cm)
Weight
6.7 lb. (3.04 kg)
Refer to the HP website at www.hp.com/networking/services for details on
the service-level descriptions and product numbers. For details about
services and response times in your area, please contact your local HP
sales office.
16 XFP 100/1000 Mbps ports
8 dual-personality ports; 1000M Combo ports (SFP or RJ-45)
c04111585 — DA – 13805 Worldwide — Version 35 — July 3, 2014
Page 56
QuickSpecs
HP 7500 Switch Series
Accessory Product Details
(JD231A)
Physical characteristics
Services
HP 7500 2-port 10GbE
XFP Enhanced Module
(JD233A)
Ports
Physical characteristics
Services
HP X124 1G SFP LC LH40
1310nm Transceiver
(JD061A)
A small form-factor
pluggable SFP Gigabit
LH40 transceiver that
provides a full duplex
Gigabit solution up to
40km on a single-mode
fiber.
Dimensions
13.98(d) x 14.84(w) x 1.57(h) in.
(35.5 x 37.7 x 4 cm)
Weight
6.7 lb. (3.04 kg)
Refer to the HP website at www.hp.com/networking/services for details on
the service-level descriptions and product numbers. For details about
services and response times in your area, please contact your local HP
sales office.
2 XFP 10-GbE ports; Duplex: full only
Dimensions
13.98(d) x 14.84(w) x 1.57(h) in.
(35.5 x 37.7 x 4 cm)
Weight
6.46 lb. (2.93 kg)
Refer to the HP website at www.hp.com/networking/services for details on
the service-level descriptions and product numbers. For details about
services and response times in your area, please contact your local HP
sales office.
Ports
Connectivity
1 LC 1000Base-LH port (no IEEE standard exists for 1550 nm optics)
Connector type
LC
Wavelength
1310 nm
Physical characteristics Dimensions
2.17(d) x 0.6(w) x 0.46(h) in. (5.51 x 1.52 x 1.17
cm)
Full configuration weight 0.04 lb. (0.02 kg)
Electrical characteristics Power consumption
0.8 W
typical
Power consumption
1.0 W
maximum
Cabling
Cable type:
Single-mode fiber optic, complying with ITU-T G.652;
Maximum distance:

Services
HP X120 1G SFP LC LH40
1550nm Transceiver
(JD062A)
40km distance
Fiber type
Single Mode
Refer to the HP website at www.hp.com/networking/services for details on
the service-level descriptions and product numbers. For details about
services and response times in your area, please contact your local HP sales
office.
Ports
Connectivity
1 LC 1000BASE-LH port (no IEEE standard exists for 1550 nm optics)
Connector type
LC
Wavelength
1550 nm
Physical characteristics Dimensions
2.17(d) x 0.6(w) x 0.46(h) in. (5.51 x 1.52 x 1.17
A small form-factor
cm)
pluggable (SFP) Gigabit
Full configuration weight 0.04 lb. (0.02 kg)
LH40 transceiver that
Electrical characteristics Power consumption
0.8 W
provides a full-duplex
typical
Gigabit solution up to 40
Power consumption
1.0 W
km on a single mode fiber.
maximum
Cabling
Cable type:
c04111585 — DA – 13805 Worldwide — Version 35 — July 3, 2014
Page 57
QuickSpecs
HP 7500 Switch Series
Accessory Product Details
Single-mode fiber optic, complying with ITU-T G.652;
Maximum distance:

Fiber type
Single Mode
Refer to the HP website at www.hp.com/networking/services for details on
the service-level descriptions and product numbers. For details about
services and response times in your area, please contact your local HP sales
office.
Services
HP X125 1G SFP LC LH70
Transceiver (JD063B)
A small form-factor
pluggable (SFP) Gigabit
LH70 transceiver that
provides a full-duplex
Gigabit solution up to
70km on a single-mode
fiber.
Ports
Connectivity
1 LC 1000BASE-LH port (no IEEE standard exists for 1550 nm optics)
Connector type
LC
Wavelength
1550 nm
Physical characteristics Dimensions
2.17(d) x 0.6(w) x 0.46(h) in. (5.51 x 1.52 x 1.17
cm)
Full configuration weight 0.04 lb. (0.02 kg)
Electrical characteristics Power consumption
0.8 W
typical
Power consumption
1.0 W
maximum
Cabling
Cable type:
Single-mode fiber optic, complying with ITU-T G.652;
Services
HP X125 1G SFP Ports
RJ45 T
Connectivity
Transceiver
Physical
(JD089B)
characteristics
Electrical
A small form
factor pluggable characteristics
(SFP) Gigabit
Cabling
1000Base-T
transceiver that
provides a full
duplex Gigabit
solution up to
100m on a Cat5+ cable.
Services
40km distance
Maximum distance:
• 70km
Fiber type
Single Mode
Refer to the HP website at www.hp.com/networking/services for details on
the service-level descriptions and product numbers. For details about
services and response times in your area, please contact your local HP
sales office.
1 RJ-45 1000BASE-T port (IEEE 802.3ab Type 1000BASE-T)
Connector type
RJ-45
Dimensions
2.71(d) x 0.54(w) x 0.55(h) in. (6.88 x 1.37 x 1.4 cm)
Full configuration weight
0.07 lb. (0.03 kg)
Power consumption typical
0.8 W
Power consumption maximum
1.0 W
Cable type:
1000BASE-T: Category 5 (5E or better recommended), 100 Ù differential 4-pair unshielded
twisted pair (UTP) or shielded twisted pair (STP) balanced, complying with IEEE 802.3ab
1000BASE-T;
Maximum distance:
• 100m
Refer to the HP website at www.hp.com/networking/services for details on the servicec04111585 — DA – 13805 Worldwide — Version 35 — July 3, 2014
Page 58
QuickSpecs
HP 7500 Switch Series
Accessory Product Details
level descriptions and product numbers. For details about services and response times in
your area, please contact your local HP sales office.
HP X120 1G SFP LC BX 10- Ports
U Transceiver (JD098B)
Connectivity
A small form-factor
Physical characteristics
pluggable (SFP) Gigabit
LX-BX10-U transceiver
that provides a full duplex
Electrical characteristics
Gigabit solution up to
10km on a single mode
cable.
Cabling
Notes
Services
HP X120 1G SFP LC BX 10- Ports
D Transceiver (JD099B)
Connectivity
A small form-factor
Physical characteristics
pluggable (SFP) Gigabit
LX-BX10-D transceiver
that provides a full duplex
Electrical characteristics
Gigabit solution up to
10km on a single mode
cable.
Cabling
Notes
Services
1 LC 1000BASE-BX10 port (IEEE 802.3ah Type 1000BASE-BX10-U); Duplex:
full only
Connector type
LC
Dimensions
2.17(d) x 0.6(w) x 0.46(h) in. (5.51 x 1.52 x 1.17
cm)
Full configuration weight 0.04 lb. (0.02 kg)
Power consumption
0.8 W
typical
Power consumption
1.0 W
maximum
Maximum distance:
• 10km
Fiber type
Single Mode
TX 1310nm RX 1490nm
Refer to the HP website at: www.hp.com/networking/services for details
on the service-level descriptions and product numbers. For details about
services and response times in your area, please contact your local HP
sales office.
1 LC 1000BASE-BX10 port (IEEE 802.3ah Type 1000BASE-BX10-D); Duplex:
full only
Connector type
LC
Dimensions
2.17(d) x 0.6(w) x 0.46(h) in. (5.51 x 1.52 x 1.17
cm)
Full configuration weight 0.04 lb. (0.02 kg)
Power consumption
0.8 W
typical
Power consumption
1.0 W
maximum
Maximum distance:
• Up to 10km
Fiber type
Single Mode
TX 1490nm RX 1310nm
Refer to the HP website at www.hp.com/networking/services for details on
the service-level descriptions and product numbers. For details about
services and response times in your area, please contact your local HP
sales office.
HP X120 1G SFP LC LH100 Ports
Transceiver (JD103A)
Connectivity
A small form factor
pluggable (SFP) Gigabit
LH100 transceiver that
provides a full-duplex
Gigabit solution up to
100km on a single mode
1 LC 1000BASE-LH port (no IEEE standard exists for 1550 nm optics)
Connector type
LC
Wavelength
1550 nm
Electrical characteristics Power consumption
0.8 W
typical
Power consumption
1.0 W
maximum
Cabling
Cable type:
c04111585 — DA – 13805 Worldwide — Version 35 — July 3, 2014
Page 59
QuickSpecs
HP 7500 Switch Series
Accessory Product Details
fiber.
Single-mode fiber optic, complying with ITU-T G.652;
Services
HP X120 1G SFP LC SX
Transceiver (JD118B)
Ports
Connectivity
HP X120 1G SFP LC LX
Transceiver (JD119B)
Ports
Connectivity
Maximum distance:
• Up to 100km
Fiber type
Single Mode
Refer to the HP website at www.hp.com/networking/services for details on
the service-level descriptions and product numbers. For details about
services and response times in your area, please contact your local HP
sales office.
1 LC 1000BASE-SX port
Connector type
Wavelength
Dimensions
LC
850 nm
A small form-factor
Physical characteristics
2.17(d) x 0.6(w) x 0.46(h) in. (5.51 x 1.52 x 1.17
pluggable (SFP) Gigabit SX
cm)
transceiver that provides
Full
configuration
weight
0.04 lb. (0.02 kg)
a full-duplex Gigabit
solution up to 550m on a Electrical characteristics Power consumption
0.8 W
Multimode fiber.
typical
Power consumption
1.0 W
maximum
Cabling
Maximum distance:
• FDDI Grade distance = 220m
• OM1 = 275m
• OM2 = 500m
• OM3 = Not Specified by standard
Cable length
up to 550m
Fiber type
Multi Mode
Services
Refer to the HP website at www.hp.com/networking/services for details on
the service-level descriptions and product numbers. For details about
services and response times in your area, please contact your local HP
sales office.
1 SFP 1000BASE-LX port (IEEE 802.3z Type 1000BASE-LX)
Connector type
LC
Wavelength
1300 nm
A small form-factor
Physical characteristics Dimensions
2.17(d) x 0.6(w) x 0.46(h) in. (5.51 x 1.52 x 1.17
pluggable (SFP) Gigabig
cm)
LX transceiver that
Full
configuration
weight
0.04 lb. (0.02 kg)
provides a full duplex
Gigabit solution up to
Electrical characteristics Power consumption
0.8 W
550m on MMF or 10Km on
typical
SMF
Power consumption
1.0 W
maximum
Cabling
Cable type:
Either single mode or multimode;
Maximum distance:
• 550m for Multimode
• 10km for Singlemode
Fiber type
Both
c04111585 — DA – 13805 Worldwide — Version 35 — July 3, 2014
Page 60
QuickSpecs
HP 7500 Switch Series
Accessory Product Details
Services
HP 50 m Multimode OM3 Cabling
LC/LC Optical Cable
(AJ839A)
Refer to the HP website at www.hp.com/networking/services for details on
the service-level descriptions and product numbers. For details about
services and response times in your area, please contact your local HP
sales office.
Cable type:
50/125 μm (core/cladding) diameter, mulitimode fiber optic, with effective
modal bandwidth of 2000 MHz/km as detailed in TIA-492AAAC for
distances of up to 300 m;
Maximum distance:
10Gbps Transfer Rate (Ethernet): 300m
Cable Specs: Tight buffered duplex fiber optic multimode OM3 50/125 um
fiber optic cable and Ethernet assembly with LC duplex connectors on one
end and LC duplex connectors on other end.
Notes











Services
HP 30 m Multimode OM3 Cabling
LC/LC Optical Cable
(AJ838A)
Notes
Dimensions: Core diameter: 50 ± 3.0um Cladding diameter: 125 ±
2.0um Coating diameter: 245 ± 10um
Optical Glass Bandwidth: For LED sources: 1500/500 MHz-km
@850/1300nm.
Optical Glass: For Laser sources: 2000/500 MHz-km
@850/1300nm. VCSEL Laser sources: Shall achieve 600 / 600
meters @850/1300nm for Gigabit Ethernet compliant links.
CABLE: The cable is duplex zipcord graded index 50/125um
multimode optical fiber. The cable is designed to work in both the
850 and 1300 nm wavelength windows.
BULK CABLE & CABLE ASSEMBLY CONFIGURATION:
Jacket Material: Riser Grade - Low Smoke Zero Halogen
thermoplastic.
Jacket Color: Aqua for OM3 multimode per TIA 598
Boot Color: White
Insertion Loss: less than 0.5 dB @ 850 with LED source, 0.003
dB/M added for lengths > 30 meters.
Maximum Cable attenuation: 3.0 dB/km @ 850 nm, 1.0 dB/Km @
1310 nm @ 23°C as tested in accordance with EIA 455-46.
Weight: Air Packed Weight: 1 LB Net Weight: 0.454Kg
Refer to the HP website at www.hp.com/networking/services for details on
the service-level descriptions and product numbers. For details about
services and response times in your area, please contact your local HP
sales office.
Cable type:
50/125 μm (core/cladding) diameter, mulitimode fiber optic, with effective
modal bandwidth of 2000 MHz/km as detailed in TIA-492AAAC for
distances of up to 300 m;
Maximum distance:
10Gbps Transfer Rate (Ethernet): 300m
Cable Specs: Tight buffered duplex fiber optic multimode OM3 50/125 um
fiber optic cable and Ethernet assembly with LC duplex connectors on one
end and LC duplex connectors on other end.
c04111585 — DA – 13805 Worldwide — Version 35 — July 3, 2014
Page 61
QuickSpecs
HP 7500 Switch Series
Accessory Product Details











Services
HP 15 m Multimode OM3 Cabling
LC/LC Optical Cable
(AJ837A)
Notes
Dimensions: Core diameter: 50 ± 3.0um Cladding diameter: 125 ±
2.0um Coating diameter: 245 ± 10um
Optical Glass Bandwidth: For LED sources: 1500/500 MHz-km
@850/1300nm.
Optical Glass: For Laser sources: 2000/500 MHz-km
@850/1300nm. VCSEL Laser sources: Shall achieve 600 / 600
meters @850/1300nm for Gigabit Ethernet compliant links.
CABLE: The cable is duplex zipcord graded index 50/125um
multimode optical fiber. The cable is designed to work in both the
850 and 1300 nm wavelength windows.
BULK CABLE & CABLE ASSEMBLY CONFIGURATION:
Jacket Material: Riser Grade - Low Smoke Zero Halogen
thermoplastic.
Jacket Color: Aqua for OM3 multimode per TIA 598
Boot Color: White
Insertion Loss: less than 0.5 dB @ 850 with LED source, 0.003
dB/M added for lengths > 30 meters.
Maximum Cable attenuation: 3.0 dB/km @ 850 nm, 1.0 dB/Km @
1310 nm @ 23°C as tested in accordance with EIA 455-46.
Weight: Air Packed Weight: 1 LB Net Weight: 0.454Kg
Refer to the HP website at www.hp.com/networking/services for details on
the service-level descriptions and product numbers. For details about
services and response times in your area, please contact your local HP
sales office.
Cable type:
50/125 μm (core/cladding) diameter, mulitimode fiber optic, with effective
modal bandwidth of 2000 MHz/km as detailed in TIA-492AAAC for
distances of up to 300 m;
Maximum distance:
10Gbps Transfer Rate (Ethernet): 300m
Cable Specs: Tight buffered duplex fiber optic multimode OM3 50/125 um
fiber optic cable and Ethernet assembly with LC duplex connectors on one
end and LC duplex connectors on other end.









Dimensions: Core diameter: 50 ± 3.0um Cladding diameter: 125 ±
2.0um Coating diameter: 245 ± 10um
Optical Glass Bandwidth: For LED sources: 1500/500 MHz-km
@850/1300nm.
Optical Glass: For Laser sources: 2000/500 MHz-km
@850/1300nm. VCSEL Laser sources: Shall achieve 600 / 600
meters @850/1300nm for Gigabit Ethernet compliant links.
CABLE: The cable is duplex zipcord graded index 50/125um
multimode optical fiber. The cable is designed to work in both the
850 and 1300 nm wavelength windows.
BULK CABLE & CABLE ASSEMBLY CONFIGURATION:
Jacket Material: Riser Grade - Low Smoke Zero Halogen
thermoplastic.
Jacket Color: Aqua for OM3 multimode per TIA 598
Boot Color: White
Insertion Loss: less than 0.5 dB @ 850 with LED source, 0.003
c04111585 — DA – 13805 Worldwide — Version 35 — July 3, 2014
Page 62
QuickSpecs
HP 7500 Switch Series
Accessory Product Details


HP 5 m Multimode OM3
LC/LC Optical Cable
(AJ836A)
Services
Refer to the HP website at www.hp.com/networking/services for details on
the service-level descriptions and product numbers. For details about
services and response times in your area, please contact your local HP
sales office.
Cabling
Cable type:
50/125 μm core/cladding) diameter, mulitimode fiber optic, with effective
modal bandwidth of 2000 MHz/km as detailed in TIA-492AAAC for
distances of up to 300 m;
Maximum distance:
10Gbps Transfer Rate (Ethernet): 300m
Cable Specs: This specification defines the detail requirements for a tight
buffered duplex fiber optic multimode OM3 50/125 um fiber optic cable
and Ethernet assembly with LC duplex connectors on one end and LC
duplex connectors on other end.
Notes











HP 2 m Multimode OM3
LC/LC Optical Cable
(AJ835A)
dB/M added for lengths > 30 meters.
Maximum Cable attenuation: 3.0 dB/km @ 850 nm, 1.0 dB/Km @
1310 nm @ 23°C as tested in accordance with EIA 455-46.
Weight: Air Packed Weight: 1 LB Net Weight: 0.454Kg
Dimensions: Core diameter: 50 ± 3.0um Cladding diameter: 125 ±
2.0um Coating diameter: 245 ± 10um
Optical Glass Bandwidth: For LED sources: 1500/500 MHz-km
@850/1300nm.
Optical Glass: For Laser sources: 2000/500 MHz-km
@850/1300nm. VCSEL Laser sources: Shall achieve 600 / 600
meters @850/1300nm for Gigabit Ethernet compliant links.
CABLE: The cable is duplex zipcord graded index 50/125um
multimode optical fiber. The cable is designed to work in both the
850 and 1300 nm wavelength windows.
BULK CABLE & CABLE ASSEMBLY CONFIGURATION:
Jacket Material: Riser Grade - Low Smoke Zero Halogen
thermoplastic.
Jacket Color: Aqua for OM3 multimode per TIA 598
Boot Color: White
Insertion Loss: less than 0.5 dB @ 850 with LED source, 0.003
dB/M added for lengths > 30 meters.
Maximum Cable attenuation: 3.0 dB/km @ 850 nm, 1.0 dB/Km @
1310 nm @ 23°C as tested in accordance with EIA 455-46.
Weight: Air Packed Weight: 1 LB Net Weight: 0.454Kg
Services
Refer to the HP website at www.hp.com/networking/services for details on
the service-level descriptions and product numbers. For details about
services and response times in your area, please contact your local HP
sales office.
Cabling
Cable type:
50/125 μm (core/cladding) diameter, mulitimode fiber optic, with effective
modal bandwidth of 2000 MHz/km as detailed in TIA-492AAAC for
distances of up to 300 m;
c04111585 — DA – 13805 Worldwide — Version 35 — July 3, 2014
Page 63
QuickSpecs
HP 7500 Switch Series
Accessory Product Details
Maximum distance:
10Gbps Transfer Rate (Ethernet): 300m
Cable Specs: Tight buffered duplex fiber optic multimode OM3 50/125 um
fiber optic cable and Ethernet assembly with LC duplex connectors on one
end and LC duplex connectors on other end.
Notes











HP 1 m Multimode OM3
LC/LC Optical Cable
(AJ834A)
Dimensions: Core diameter: 50 ± 3.0um Cladding diameter: 125 ±
2.0um Coating diameter: 245 ± 10um
Optical Glass Bandwidth: For LED sources: 1500/500 MHz-km
@850/1300nm.
Optical Glass: For Laser sources: 2000/500 MHz-km
@850/1300nm. VCSEL Laser sources: Shall achieve 600 / 600
meters @850/1300nm for Gigabit Ethernet compliant links.
CABLE: The cable is duplex zipcord graded index 50/125um
multimode optical fiber. The cable is designed to work in both the
850 and 1300 nm wavelength windows.
BULK CABLE & CABLE ASSEMBLY CONFIGURATION:
Jacket Material: Riser Grade - Low Smoke Zero Halogen
thermoplastic.
Jacket Color: Aqua for OM3 multimode per TIA 598
Boot Color: White
Insertion Loss: less than 0.5 dB @ 850 with LED source, 0.003
dB/M added for lengths > 30 meters.
Maximum Cable attenuation: 3.0 dB/km @ 850 nm, 1.0 dB/Km @
1310 nm @ 23°C as tested in accordance with EIA 455-46.
Weight: Air Packed Weight: 1 LB Net Weight: 0.454Kg
Services
Refer to the HP website at www.hp.com/networking/services for details on
the service-level descriptions and product numbers. For details about
services and response times in your area, please contact your local HP
sales office.
Cabling
Cable type:
50/125 μm (core/cladding) diameter, mulitimode fiber optic, with effective
modal bandwidth of 2000 MHz/km as detailed in TIA-492AAAC for
distances of up to 300 m
Notes
Maximum distance:
10Gbps Transfer Rate (Ethernet): 300m
Cable Specs: Tight buffered duplex fiber optic multimode OM3 50/125 um
fiber optic cable and Ethernet assembly with LC duplex connectors on one
end and LC duplex connectors on other end.




Dimensions: Core diameter: 50 ± 3.0um Cladding diameter: 125 ±
2.0um Coating diameter: 245 ± 10um
Optical Glass Bandwidth: For LED sources: 1500/500 MHz-km
@850/1300nm.
Optical Glass: For Laser sources: 2000/500 MHz-km
@850/1300nm. VCSEL Laser sources: Shall achieve 600 / 600
meters @850/1300nm for Gigabit Ethernet compliant links.
CABLE: The cable is duplex zipcord graded index 50/125um
multimode optical fiber. The cable is designed to work in both the
850 and 1300 nm wavelength windows.
c04111585 — DA – 13805 Worldwide — Version 35 — July 3, 2014
Page 64
QuickSpecs
HP 7500 Switch Series
Accessory Product Details







Services
HP 0.5 m Multimode OM3 Cabling
LC/LC Optical Cable
(AJ833A)
BULK CABLE & CABLE ASSEMBLY CONFIGURATION:
Jacket Material: Riser Grade - Low Smoke Zero Halogen
thermoplastic.
Jacket Color: Aqua for OM3 multimode per TIA 598
Boot Color: White
Insertion Loss: less than 0.5 dB @ 850 with LED source, 0.003
dB/M added for lengths > 30 meters.
Maximum Cable attenuation: 3.0 dB/km @ 850 nm, 1.0 dB/Km @
1310 nm @ 23°C as tested in accordance with EIA 455-46.
Weight: Air Packed Weight: 1 LB Net Weight: 0.454Kg
Refer to the HP website at www.hp.com/networking/services for details on
the service-level descriptions and product numbers. For details about
services and response times in your area, please contact your local HP
sales office.
Cable type:
50/125 μm (core/cladding) diameter, mulitimode fiber optic, with effective
modal bandwidth of 2000 MHz/km as detailed in TIA-492AAAC for
distances of up to 300 m
Maximum distance:
10Gbps Transfer Rate (Ethernet): 300m
Cable Specs: Tight buffered duplex fiber optic multimode OM3 50/125 um
fiber optic cable and Ethernet assembly with LC duplex connectors on one
end and LC duplex connectors on other end.
Notes











Services
Dimensions: Core diameter: 50 ± 3.0um Cladding diameter: 125 ±
2.0um Coating diameter: 245 ± 10um
Optical glass: Bandwidth: For LED sources: 1500/500 MHz-km
@850/1300nm.
Optical glass: Bandwidth: For Laser sources: 2000/500 MHz-km
@850/1300nm. VCSEL Laser sources: 600 / 600 meters
@850/1300nm for Gigabit Ethernet compliant links.
CABLE: The cable is duplex zipcord graded index 50/125um
multimode optical fiber and designed to work in both the 850 and
1300 nm wavelength windows.
BULK CABLE & CABLE ASSEMBLY CONFIGURATION:
Jacket Material: Riser Grade - Low Smoke Zero Halogen
thermoplastic.
Jacket Color: Aqua for OM3 multimode per TIA 598
Boot Color: White
Insertion Loss: less than 0.5 dB @ 850 with LED source, 0.003
dB/M added for lengths > 30 meters.
Maximum Cable attenuation: 3.0 dB/km @ 850 nm, 1.0 dB/Km @
1310 nm @ 23°C as tested in accordance with EIA 455-46.
Weight: Air Packed Weight: 1 LB Net Weight: 0.454Kg
Refer to the HP website at www.hp.com/networking/services for details on
the service-level descriptions and product numbers. For details about
services and response times in your area, please contact your local HP
sales office.
c04111585 — DA – 13805 Worldwide — Version 35 — July 3, 2014
Page 65
QuickSpecs
HP 7500 Switch Series
Accessory Product Details
HP 1 m PremierFlex OM3+ Notes
LC/LC Optical Cable
(BK838A)
Cable Specs: Graded-index, "bendable" fiber optic multimode OM3+
50/125um duplex cable and Ethernet assembly with LC duplex connectors
on each end.
Services
• Core Diameter: 50um ±3um, Cladding diameter: 125um ±2um; Coating
diameter: 245 ± 10um
• Bandwidth: 3000 MHz-km @ 850nm (Laser)
• Jacket Color: Blue
• Jacket Material: Riser Grade – Low Smoke Zero Halogen (LSZH)
thermoplastic
• Boot Color: White
• Outer Jacket Print: HP PremierFlex OM3+ Fiber Optic Cable, 50/125um,
Type OFNR (UL), LSZH, cUL, OFN FT4, ROHS. Cable also has a longitudinal
white stripe that runs the entire length of the cable.
• Insertion Loss: Less than 0.5dB @ 850nm with LED source, 0.003dB/m
added for lengths >30m
• Maximum Cable Attenuation: 3.0 dB/km @ 850nm, 1.0 dB/km @ 1310nm
@ 23°C as tested in accordance with EIA 455-45
Refer to the HP website at www.hp.com/networking/services for details on
the service-level descriptions and product numbers. For details about
services and response times in your area, please contact your local HP
sales office.
HP 10500/7500 20G Unified Wired-WLAN Module (JG639A)
Ports
1 RJ-45 serial console port (IEEE 802.3 Type 10BASE-T, IEEE 802.3u Type 100BASE-TX, IEEE 802.3ab
Type 1000BASE-T); Duplex: 10BASE-T/100BASE-TX: half or full; 1000BASE-T: full only
1 RJ-45 out-of-band management port (IEEE 802.3 Type 10BASE-T, IEEE 802.3u Type 100BASE-TX,
IEEE 802.3ab Type 1000BASE-T); Duplex: 10BASE-T/100BASE-TX: half or full; 1000BASE-T: full only
Physical characteristics Dimensions
15.71(w) x 13.98(d) x 1.57(h) in (39.9 x 35.5 x 4.0 cm) (1U height)
Weight
7.98 lb (3.62 kg)
Memory and processor
Processor
Eight core @ 950 MHz, 1 GB compact flash, 2 GB DDR2 DIMM
Performance
Switch fabric speed
10 Gbps
MAC address table size
24000 entries
Environment
Operating temperature 32°F to 113°F (0°C to 45°C)
Operating relative
5% to 95%, noncondensing
humidity
Nonoperating/Storage
-40°F to 158°F (-40°C to 70°C)
temperature
Nonoperating/Storage
5% to 95%, noncondensing
relative humidity
Electrical characteristics Maximum heat
512 BTU/hr (540.16 kJ/hr)
dissipation
Maximum power rating 150 W
Notes
Power consumption: 118 W-150 W
Safety
UL 60950-1; CAN/CSA 22.2 No. 60950-1; IEC 60950-1; EN 60950-1; FDA 21 CFR Subchapter J
Emissions
EN 55022 Class A; CISPR 22 Class A; ICES-003 Class A; AS/NZS CISPR 22 Class A; EN 61000-3-2; EN
61000-3-3; VCCI-3 CLASS A; VCCI-4 CLASS A; ETSI EN 300 386; FCC Part 15 (CFR 47) CLASS A
Immunity
EN
EN 55024, CISPR24 & ETSI EN 300 386
Management
IMC - Intelligent Management Center; command-line interface; Web browser; SNMP Manager; Telnet;
HTTPS; RMON1; FTP; in-line and out-of-band; IEEE 802.3 Ethernet MIB; Ethernet Interface MIB
c04111585 — DA – 13805 Worldwide — Version 35 — July 3, 2014
Page 66
QuickSpecs
HP 7500 Switch Series
Accessory Product Details
Features
Services
For use in HP 10500 Switch Series and HP 7500 Switch Series
Default supported APs: 128
Maximum supported APs: 1,024 (via the optional purchase of the 128-Access Point E-LTU)
Maximum supported users: 20,000
Maximum supported users via local portal authentication: 4,000
Maximum supported users via local authentication: 1,000
Maximum supported configured SSIDs: 512
Maximum supported ACLs: 32,000
Supported MSM APs are automatically discovered, Comware firmware is loaded, and the APs can be
fully managed.
Refer to the HP website at: www.hp.com/networking/services for details on the service-level
descriptions and product numbers. For details about services and response times in your area, please
contact your local HP sales office.
Standards and protocols
General protocols
RFC 768 UDP
RFC 791 IP
RFC 792 ICMP
RFC 793 TCP
RFC 826 ARP
RFC 854 TELNET
RFC 855 Telnet Option Specification
RFC 858 Telnet Suppress Go Ahead Option
RFC 894 IP over Ethernet
RFC 950 Internet Standard Subnetting
Procedure
RFC 959 File Transfer Protocol (FTP)
RFC 1122 Host Requirements
RFC 1141 Incremental updating of the
Internet
checksum
RFC 1144 Compressing TCP/IP headers for
low-speed
serial links
RFC 1256 ICMP Router Discovery Protocol
(IRDP)
RFC 1321 The MD5 Message-Digest
Algorithm
RFC 1334 PPP Authentication Protocols
(PAP)
RFC 1350 TFTP Protocol (revision 2)
RFC 1812 IPv4 Routing
RFC 1944 Benchmarking Methodology for
Network
Interconnect Devices
RFC 1994 PPP Challenge Handshake
Authentication
Protocol (CHAP)
RFC 2104 HMAC: Keyed-Hashing for
Message
Authentication
RFC 2246 The TLS Protocol Version 1.0
RFC 2284 EAP over LAN
RFC 2461 IPv6 Neighbor Discovery
RFC 2462 IPv6 Stateless Address Autoconfiguration
RFC 2463 ICMPv6
RFC 2464 Transmission of IPv6 over
Ethernet Networks
RFC 2465 Management Information Base
for IP Version
6: Textual Conventions and General
Group(partially
support, only "IPv6 Interface Statistics
table")
RFC 2466, Management Information Base
for IP Version
6 - ICMPv6
RFC 2526 Reserved IPv6 Subnet Anycast
Addresses
RFC 2553 Basic Socket Interface
Extensions for IPv6
RFC 2563 ICMPv6
RFC 2925 Definitions of Managed Objects
for Remote
Ping, Traceroute, and Lookup Operations
(Ping only)
RFC 3315 DHCPv6 (client and relay)
RFC 3363 DNS support
RFC 3484 Default Address Selection for
IPv6
RFC 3493 Basic Socket Interface
Extensions for IPv6
RFC 3513 IPv6 Addressing Architecture
RFC 3542 Advanced Sockets API for IPv6
RFC 3587 IPv6 Global Unicast Address
Format
RFC 3596 DNS Extension for IPv6
RFC 4193, Unique Local IPv6 Unicast
Addresses
RFC 4443 ICMPv6
RFC 4541 IGMP & MLD Snooping Switch
RFC 4861 IPv6 Neighbor Discovery
RFC 4862 IPv6 Stateless Address Auto-
IEEE 802.11i Medium Access Control (MAC)
Security Enhancements
IEEE 802.11n WLAN Enhancements for
Higher Throughput
Note: All of the above standards are now
included in IEEE 802.11-2012
Network management
RFC 1155 Structure of Management
Information
RFC 1905 SNMPv2 Protocol Operations
RFC 2573 SNMPv3 Applications
RFC 2574 SNMPv3 User-based Security
Model (USM)
RFC 2575 VACM for SNMP
SNMPv1/v2c
QoS/CoS
RFC 2474 DS Field in the IPv4 and IPv6
Headers
RFC 2474 DSCP DiffServ
RFC 2475 DiffServ Architecture
RFC 3168 The Addition of Explicit
Congestion
Notification (ECN) to IP
WiFi MultiMedia (WMM), IEEE 802.11e
Security
IEEE 802.1X Port Based Network Access
Control
RFC 3394 Advanced Encryption Standard
(AES) Key Wrap
Algorithm
RFC 3579 RADIUS Support For Extensible
Authentication Protocol (EAP)
Access Control Lists (ACLs)
Guest VLAN for 802.1x
Secure Sockets Layer (SSL)
SSHv2 Secure Shell
Web Authentication
c04111585 — DA – 13805 Worldwide — Version 35 — July 3, 2014
Page 67
QuickSpecs
HP 7500 Switch Series
Accessory Product Details
RFC 2644 Directed Broadcast Control
RFC 2864 The Inverted Stack Table
Extension to the
Interfaces Group MIB
RFC 2866 RADIUS Accounting
RFC 2869 RADIUS Extensions
RFC 3268 Advanced Encryption Standard
(AES)
Ciphersuites for Transport Layer Security
(TLS)
RFC 3619 Ethernet Automatic Protection
Switching
(EAPS)
configuration
RFC 5095 Deprecation of Type 0 Routing
Headers in IPv6
MIBs
RFC 1229 Interface MIB Extensions
RFC 1643 Ethernet MIB
RFC 1757 Remote Network Monitoring MIB
RFC 2011 SNMPv2 MIB for IP
RFC 2012 SNMPv2 MIB for TCP
RFC 2013 SNMPv2 MIB for UDP
RFC 2571 SNMP Framework MIB
RFC 2572 SNMP-MPD MIB
RFC 2613 SMON MIB
RFC 2863 The Interfaces Group MIB
RFC 2932IP (Multicast Routing MIB)
RFC 2933 IGMP MIB
WPA (Wi-Fi Protected Access)/WPA2
IKEv1
RFC 3748 - Extensible Authentication
Protocol (EAP)
IP multicast
RFC 1112 IGMP
RFC 2236 IGMPv2
RFC 2934 Protocol Independent Multicast
MIB for IPv4
Mobility
IEEE 802.11a High Speed Physical Layer in
IPv6
the 5 GHz Band
RFC 1350 TFTP
IEEE 802.11b Higher-Speed Physical Layer
RFC 1881 IPv6 Address Allocation
Extension in the 2.4 GHz Band
Management
IEEE 802.11d Global Harmonization
RFC 1887 IPv6 Unicast Address Allocation IEEE 802.11e QoS enhancements
Architecture
IEEE 802.11g Further Higher Data Rate
RFC 1981 IPv6 Path MTU Discovery
Extension in the 2.4 GHz Band
RFC 2292 Advanced Sockets API for IPv6 IEEE 802.11h Dynamic Frequency
RFC 2373 IPv6 Addressing Architecture
Selection
RFC 2375 IPv6 Multicast Address
Assignments
RFC 2460 IPv6 Specification
HP 7500 Access Controller Module (JD440A)
Ports
1 RJ-45 serial console port
1 RJ-45 out-of-band management port
2 USB 1.0 12 Mbps ports
Physical characteristics Dimensions
14.45(d) x 13.39(w) x 1.6(h) in. (36.7 x 34 x 4.06 cm) (1U height)
Weight
7.28 lb. (3.3 kg)
Memory and processor
Processor
Eight core @ 950 MHz, 256 MB compact flash, 1 GB DDR2 DIMM
Performance
Switch fabric speed
20 Gbps
MAC address table size
24000 entries
Environment
Operating temperature 32°F to 113°F (0°C to 45°C)
Operating relative
5% to 95%, noncondensing
humidity
Nonoperating/Storage
-40°F to 158°F (-40°C to 70°C)
temperature
Nonoperating/Storage
5% to 95%, noncondensing
relative humidity
Electrical characteristics Maximum heat
273 BTU/hr (288.02 kJ/hr)
dissipation
Maximum power rating 80 W
c04111585 — DA – 13805 Worldwide — Version 35 — July 3, 2014
Page 68
QuickSpecs
HP 7500 Switch Series
Accessory Product Details
Safety
Emissions
Immunity
Management
Features
Notes
Services
UL 60950-1; EN 60950-1; CAN/CSA-C22.2 No. 60950-1; Anatel; GOST; C-Tick; NOM; IEC 60950-1(with
CB report)
EN 55022; VCCI; ICES-003; AS/NZS CISPR 22; EN 300 386; FCC Part 15; EN 61000-3-2:2006; EN 610003-3:1995 +A1:2001+A2:2005; EMC Directive 2004/108/EC
EN
EN 61000-4-2:1995+A1:1998+A2:2001; EN 61000-4-3:2006; EN 61000-44:2004; EN 61000-4-5:2006; EN 61000-4-6: 1996 +A1:2001:A2:2007; EN
61000-4-8:2001; EN 61000-4-11:2004; EN 55024:1998+ A1:2001 +
A2:2003
IMC - Intelligent Management Center; command-line interface; Web browser; configuration menu;
SNMP Manager; Telnet; HTTPS; RMON1; FTP; in-line and out-of-band; IEEE 802.3 Ethernet MIB;
Ethernet Interface MIB
A7500 ACM License system
- The A7500 ACM is an access controller module for the HP A7500 series Ethernet switches. It supports
128 APs by default. After license upgrade, the access controller module can support up to 640 APs.
Max. number of users: 20K. Max. number of users that are supported by local authentication: 1K. Max.
number of SSIDs that can be configured: 512. Max. number of users that are supported by local portal
authentication: 4K. Number of ACLs: 32K.
Refer to the HP website at: www.hp.com/networking/services for details on the service-level
descriptions and product numbers. For details about services and response times in your area, please
contact your local HP sales office.
Standards and protocols General protocols
RFC 768 UDP
RFC 791 IP
RFC 792 ICMP
RFC 793 TCP
RFC 826 ARP
RFC 854 TELNET
RFC 855 Telnet Option Specification
RFC 858 Telnet Suppress Go Ahead Option
RFC 894 IP over Ethernet
RFC 950 Internet Standard Subnetting Procedure
RFC 959 File Transfer Protocol (FTP)
RFC 1122 Host Requirements
RFC 1141 Incremental updating of the Internet
checksum
RFC 1144 Compressing TCP/IP headers for
low-speed serial links
RFC 1256 ICMP Router Discovery Protocol (IRDP)
RFC 1321 The MD5 Message-Digest Algorithm
RFC 1334 PPP Authentication Protocols (PAP)
RFC 1350 TFTP Protocol (revision 2)
RFC 1812 IPv4 Routing
RFC 1944 Benchmarking Methodology for Network
Interconnect Devices
RFC 1994 PPP Challenge Handshake
Authentication
Protocol (CHAP)
RFC 2104 HMAC: Keyed-Hashing for Message
Authentication
RFC 2246 The TLS Protocol Version 1.0
RFC 2284 EAP over LAN
RFC 2644 Directed Broadcast Control
RFC 2864 The Inverted Stack Table Extension to
the
MIBs
RFC 1229 Interface MIB Extensions
RFC 1643 Ethernet MIB
RFC 1757 Remote Network Monitoring MIB
RFC 2011 SNMPv2 MIB for IP
RFC 2012 SNMPv2 MIB for TCP
RFC 2013 SNMPv2 MIB for UDP
RFC 2571 SNMP Framework MIB
RFC 2572 SNMP-MPD MIB
RFC 2613 SMON MIB
RFC 2863 The Interfaces Group MIB
RFC 2933 IGMP MIB
Mobility
IEEE 802.11a High Speed Physical Layer in the 5
GHz Band
IEEE 802.11b Higher-Speed Physical Layer
Extension in the 2.4 GHz Band
IEEE 802.11d Global Harmonization
IEEE 802.11g Further Higher Data Rate Extension
in
the 2.4 GHz Band
IEEE 802.11i Medium Access Control (MAC)
Security Enhancements
IEEE 802.11n WLAN Enhancements for Higher
Throughput
Network management
RFC 1155 Structure of Management Information
RFC 1905 SNMPv2 Protocol Operations
RFC 2573 SNMPv3 Applications
RFC 2574 SNMPv3 User-based Security Model
(USM)
RFC 2575 VACM for SNMP
c04111585 — DA – 13805 Worldwide — Version 35 — July 3, 2014
Page 69
QuickSpecs
HP 7500 Switch Series
Accessory Product Details
Interfaces Group MIB
RFC 2866 RADIUS Accounting
RFC 2869 RADIUS Extensions
RFC 3268 Advanced Encryption Standard (AES)
Ciphersuites for Transport Layer Security (TLS)
RFC 3619 Ethernet Automatic Protection Switching
(EAPS)
IP multicast
RFC 1112 IGMP
RFC 2236 IGMPv2
RFC 2934 Protocol Independent Multicast MIB for
IPv4
IPv6
RFC 1350 TFTP
RFC 1881 IPv6 Address Allocation Management
RFC 1887 IPv6 Unicast Address Allocation
Architecture
RFC 1981 IPv6 Path MTU Discovery
RFC 2292 Advanced Sockets API for IPv6
RFC 2373 IPv6 Addressing Architecture
RFC 2375 IPv6 Multicast Address Assignments
RFC 2460 IPv6 Specification
RFC 2461 IPv6 Neighbor Discovery
RFC 2462 IPv6 Stateless Address Autoconfiguration
RFC 2463 ICMPv6
RFC 2464 Transmission of IPv6 over Ethernet
Networks
RFC 2526 Reserved IPv6 Subnet Anycast
Addresses
RFC 2563 ICMPv6
RFC 2925 Definitions of Managed Objects for
Remote Ping, Traceroute, and Lookup Operations
(Ping only)
RFC 3484 Default Address Selection for IPv6
RFC 3587 IPv6 Global Unicast Address Format
RFC 4443 ICMPv6
RFC 4541 IGMP & MLD Snooping Switch
RFC 4861 IPv6 Neighbor Discovery
RFC 4862 IPv6 Stateless Address Autoconfiguration
RFC 5095 Deprecation of Type 0 Routing Headers
in IPv6
SNMPv1/v2c
QoS/CoS
RFC 2474 DS Field in the IPv4 and IPv6 Headers
RFC 2474 DSCP DiffServ
RFC 2475 DiffServ Architecture
RFC 3168 The Addition of Explicit Congestion
Notification (ECN) to IP
WiFi MultiMedia (WMM), IEEE 802.11e
Security
IEEE 802.1X Port Based Network Access Control
RFC 3394 Advanced Encryption Standard (AES)
Key Wrap Algorithm
RFC 3579 RADIUS Support For Extensible
Authentication Protocol (EAP)
Access Control Lists (ACLs)
Guest VLAN for 802.1x
Secure Sockets Layer (SSL)
SSHv1.5 Secure Shell
SSHv2 Secure Shell
Web Authentication
WPA (Wi-Fi Protected Access)/WPA2
IKEv1
RFC 3748 - Extensible Authentication Protocol
(EAP)
HP TippingPoint S1200N Ports
IPS A7500 Module
(JC527A)
2 SFP 1000 Mbps ports
2 RJ-45 1000 Mbps ports
1 Compact Flash port
1 RJ-45 serial console port (IEEE 802.3 Type 10BASE-T, IEEE 802.3u Type
100BASE-TX, IEEE 802.3ab Type 1000BASE-T)
Duplex: 10BASE-T/100BASE-TX: half or full; 1000BASE-T: full only
Physical characteristics Dimensions
13.7(d) x 15.7(w) x 1.6(h) in. (34.8 x 39.88 x
4.06 cm)
Weight
7.7 lb. (3.49 kg), Fully loaded
Electrical characteristics Throughput
up to 1.3 Gbps
c04111585 — DA – 13805 Worldwide — Version 35 — July 3, 2014
Page 70
QuickSpecs
HP 7500 Switch Series
Accessory Product Details
IPS/IDS throughput
1.3 Gbps inspected throughput
Concurrent sessions
6,500,000
New sessions/second
78K
Environment
Operating temperature 32°F to 113°F (0°C to 45°C)
Operating relative
10% to 95%, noncondensing
humidity
Nonoperating/Storage
-20°F to 45°F (-28.9°C to 7.2°C)
temperature
Services
Refer to the HP website at: www.hp.com/networking/services for details on
the service-level descriptions and product numbers. For details about
services and response times in your area, please contact your local HP sales
office.
Standards and protocols Denial of service
Automatic filtering of well-known denial-ofprotection
service
packets
Rate Limiting by ACLs
IPv6
RFC 2460 IPv6 Specification
HP 7500 384Gbps Fabric Ports
Module with 2 XFP Ports
(JD193B)
Physical characteristics
Services
HP 7500 384Gbps Fabric Ports
Module (JD194B)
Physical characteristics
Services
HP 7500 384Gbps
Ports
Advanced Fabric Module
(JD195A)
Physical characteristics
1 RJ-45 dual-personality port; One console port, used for local or remote
configuration and management
1 RJ-45 autosensing 10/100 port (IEEE 802.3 Type 10BASE-T, IEEE 802.3u
Type 100BASE-TX); Duplex: half or full
1 Compact Flash port
2 XFP 10-GbE ports; Duplex: full only
Dimensions
13.98(d) x 14.84(w) x 1.77(h) in. (35.5 x 37.7 x
4.5 cm)
Weight
7.94 lb. (3.6 kg)
Refer to the HP website at www.hp.com/networking/services for details on
the service-level descriptions and product numbers. For details about
services and response times in your area, please contact your local HP
sales office.
1 RJ-45 dual-personality port; One console port, used for local or remote
configuration and management
1 RJ-45 autosensing 10/100 port (IEEE 802.3 Type 10BASE-T, IEEE 802.3u
Type 100BASE-TX); Duplex: half or full
1 Compact Flash port
Dimensions
13.98(d) x 14.84(w) x 1.77(h) in. (35.5 x 37.7 x
4.5 cm)
Weight
7.94 lb. (3.6 kg)
Refer to the HP website at www.hp.com/networking/services for details on
the service-level descriptions and product numbers. For details about
services and response times in your area, please contact your local HP
sales office.
1 RJ-45 dual-personality port; One console port, used for local or remote
configuration and management
1 RJ-45 autosensing 10/100 port (IEEE 802.3 Type 10BASE-T, IEEE 802.3u
Type 100BASE-TX); Duplex: half or full
1 Compact Flash port
Dimensions
13.98(d) x 14.84(w) x 1.77(h) in. (35.5 x 37.7 x
4.5 cm)
c04111585 — DA – 13805 Worldwide — Version 35 — July 3, 2014
Page 71
QuickSpecs
HP 7500 Switch Series
Accessory Product Details
Services
HP 7500 768Gbps Fabric Ports
Module (JD220A)
Physical characteristics
Services
Weight
7.94 lb. (3.6 kg)
Refer to the HP website at www.hp.com/networking/services for details on
the service-level descriptions and product numbers. For details about
services and response times in your area, please contact your local HP
sales office.
1 RJ-45 dual-personality port; One console port, used for local or remote
configuration and management
1 RJ-45 autosensing 10/100 port (IEEE 802.3 Type 10BASE-T, IEEE 802.3u
Type 100BASE-TX); Duplex: half or full
1 Compact Flash port
Dimensions
13.98(d) x 14.84(w) x 1.77(h) in. (35.5 x 37.7 x
4.5 cm)
Weight
7.85 lb. (3.56 kg)
Refer to the HP website at www.hp.com/networking/services for details on
the service-level descriptions and product numbers. For details about
services and response times in your area, please contact your local HP
sales office.
HP 7500 1400W DC Power Physical characteristics
Supply (JD208A)
Dimensions
HP 7500 1400W AC Power Physical characteristics
Supply (JD218A)
Dimensions
7.72(w) x 14.06(d) x 5.04(h) in (19.6 x 35.7 x
12.8 cm) (3U height)
Weight
20.39 lb (9.25 kg)
Electrical characteristics Voltage
0~-48/-60V
Current
0/50 A
Idle power
168 W
Maximum power rating 1400 W
PoE power
140 W
Notes
Idle power is the actual power consumption of
the device with no ports connected.
Maximum power rating and maximum heat
dissipation are the worst-case theoretical
maximum numbers provided for planning the
infrastructure with fully loaded PoE (if
equipped), 100% traffic, all ports plugged in,
and all modules populated.
Services
Refer to the HP website at www.hp.com/networking/services for details on
the service-level descriptions and product numbers. For details about
services and response times in your area, please contact your local HP
sales office.
Weight
Electrical characteristics Voltage
Current
Idle power
Maximum power rating
PoE power
Frequency
Notes
7.72(w) x 14.06(d) x 5.04(h) in (19.6 x 35.7 x
12.8 cm) (3U height)
14 lb (6.35 kg)
100-120/200-240 VAC
0/16 A
196 W
1400 W
0W
50/60 Hz
Idle power is the actual power consumption of
c04111585 — DA – 13805 Worldwide — Version 35 — July 3, 2014
Page 72
QuickSpecs
HP 7500 Switch Series
Accessory Product Details
Notes
Services
the device with no ports connected.
Maximum power rating and maximum heat
dissipation are the worst-case theoretical
maximum numbers provided for planning the
infrastructure with fully loaded PoE (if
equipped), 100% traffic, all ports plugged in,
and all modules populated.
1400W AC Power Supply uses a 16-A AC power
cable
US order needs to indicate either #ABA option (for 110V) or #B2E (for
220V). This will determine which power cord the distribution centres
include with the product.
Refer to the HP website at www.hp.com/networking/services for details on
the service-level descriptions and product numbers. For details about
services and response times in your area, please contact your local HP
sales office.
HP 7500 6000W AC Power Physical characteristics
Supply (JD227A)
Dimensions
HP 7503 Fabric Module
with 24 GbE Ports
(JD222A)
1 RJ-45 dual-personality port; One console port, used for local or remote
configuration and management
1 RJ-45 autosensing 10/100 port (IEEE 802.3 Type 10BASE-T, IEEE 802.3u
Type 100BASE-TX); Duplex: half or full
16 SFP 100/1000 Mbps ports
8 dual-personality ports; Combo ports (RJ45 or SFP)
Dimensions
14.84(w) x 13.98(d) x 1.77(h) in
(37.7 x 35.5 x 4.5 cm)
7.72(w) x 14.06(d) x 5.04(h) in (19.6 x 35.7 x
12.8 cm) (3U height)
Weight
28.22 lb (12.8 kg)
Electrical characteristics Voltage
100-120/200-240 VAC
Current
0/16 A
Idle power
105 W
Maximum power rating 6000 W
PoE power
5300 W
Frequency
50/60 Hz
Notes
Idle power is the actual power consumption of
the device with no ports connected.
Maximum power rating and maximum heat
dissipation are the worst-case theoretical
maximum numbers provided for planning the
infrastructure with fully loaded
PoE (if equipped), 100% traffic, all ports
plugged in, and all modules populated.
6000W AC Power Supply uses a 16-A AC power
cable.
Notes
US order needs to indicate either #ABA option (for 110V) or #B2E (for
220V). This will determine which power cord the distribution centres
include with the product.
Services
Refer to the HP website at www.hp.com/networking/services for details on
the service-level descriptions and product numbers. For details about
services and response times in your area, please contact your local HP
sales office.
Ports
Physical characteristics
c04111585 — DA – 13805 Worldwide — Version 35 — July 3, 2014
Page 73
QuickSpecs
HP 7500 Switch Series
Accessory Product Details
Services
HP 7503-S 144 Gbps
Ports
Fabric / Main Processing
Unit with PoEupgradable 20p Gig-T /
4p GbE Combo (JC666A)
Physical characteristics
Services
HP 7503-S 144 Gbps TAA Ports
Fabric/Main Processing
Unit with 16 GbE SFP
Ports and 8 GbE Combo
Ports (JC698A)
Physical characteristics
Services
HP 7500 650W AC Power Physical characteristics
Supply (JD217A)
Weight
6.17 lb (2.8 kg)
Refer to the HP website at www.hp.com/networking/services for details on
the service-level descriptions and product numbers. For details about
services and response times in your area, please contact your local HP
sales office.
1 RJ-45 serial console port; One console port, used for local or remote
configuration and management of the switch through a dialup connection
1 RJ-45 autosensing 10/100 port (IEEE 802.3 Type 10BASE-T, IEEE 802.3u
Type 100BASE-TX); Duplex: half or full
20 RJ-45 auto-negotiating 10/100/1000 PoE ports (IEEE 802.3 Type
10BASE-T, IEEE 802.3u Type 100BASE-TX, IEEE 802.3ab Type 1000BASE-T,
IEEE 802.3af PoE); Duplex: 10BASE-T/100BASE-TX: half or full; 1000BASET: full only
4 dual-personality ports; each of which consists of a 10/100/1000Base-T
port and an SFP port. The two ports comprising a Combo port cannot
operate at the same time.
Dimensions
13.98(w) x 14.84(d) x 1.77(h) in (35.51 x 37.69 x
4.5 cm)
Weight
6.31 lb (2.86 kg)
Refer to the HP website at www.hp.com/networking/services for details on
the service-level descriptions and product numbers. For details about
services and response times in your area, please contact your local HP
sales office.
1 RJ-45 dual-personality port; One console port, used for local or remote
configuration and management
1 RJ-45 autosensing 10/100 port (IEEE 802.3 Type 10BASE-T, IEEE 802.3u
Type 100BASE-TX); Duplex: half or full
16 SFP 100/1000 Mbps ports
8 dual-personality ports; Combo ports (RJ45 or SFP)
Dimensions
13.98(d) x 14.84(w) x 1.77(h) in. (35.5 x 37.7 x
4.5 cm)
Weight
6.17 lb. (2.8 kg)
Refer to the HP website at www.hp.com/networking/services for details on
the service-level descriptions and product numbers. For details about
services and response times in your area, please contact your local HP
sales office.
Dimensions
Weight
Electrical characteristics Voltage
Current
Idle power
Maximum power rating
PoE power
Frequency
Notes
5.51(w) x 13.78(d) x 1.57(h) in (14 x 35 x 4 cm)
(1U height)
5.34 lb (2.42 kg)
100-120/200-240 VAC
0/10 A
97.5 W
650 W
0W
50/60 Hz
Idle power is the actual power consumption of
the device with no ports connected.
Maximum power rating and maximum heat
c04111585 — DA – 13805 Worldwide — Version 35 — July 3, 2014
Page 74
QuickSpecs
HP 7500 Switch Series
Accessory Product Details
Services
dissipation are the worst-case theoretical
maximum numbers provided for planning the
infrastructure with fully loaded
PoE (if equipped), 100% traffic, all ports
plugged in, and all modules populated.
650W AC Power Supply uses a 10-A AC power
cable
Refer to the HP website at www.hp.com/networking/services for details on
the service-level descriptions and product numbers. For details about
services and response times in your area, please contact your local HP
sales office.
HP 7500 650W DC Power Physical characteristics
Supply (JD209A)
Dimensions
HP 7502 300W AC Power Physical characteristics
Supply (JD226A)
Dimensions
5.51(w) x 13.78(d) x 1.57(h) in (14 x 35 x 4 cm)
(1U height)
Weight
4.96 lb (2.25 kg)
Electrical characteristics Voltage
0~-48/-60V
Current
0/25 A
Idle power
97.5 W
Maximum power rating 650 W
PoE power
0W
Notes
Idle power is the actual power consumption of
the device with no ports connected.
Maximum power rating and maximum heat
dissipation are the worst-case theoretical
maximum numbers provided for planning the
infrastructure with fully loaded
PoE (if equipped), 100% traffic, all ports
plugged in, and all modules populated.
Services
Refer to the HP website at www.hp.com/networking/services for details on
the service-level descriptions and product numbers. For details about
services and response times in your area, please contact your local HP
sales office.
Weight
Electrical characteristics Voltage
Current
Idle power
Maximum power rating
PoE power
Frequency
Notes
5.51(w) x 13.78(d) x 1.57(h) in (14 x 35 x 4 cm)
(1U height)
4.17 lb (1.89 kg)
100-120/200-240 VAC
0/5 A
54 W
300 W
0W
50/60 Hz
Idle power is the actual power consumption of
the device with no ports connected.
Maximum power rating and maximum heat
dissipation are the worst-case theoretical
maximum numbers provided for planning the
infrastructure with fully loaded
PoE (if equipped), 100% traffic, all ports
plugged in, and all modules populated.
300W AC Power Supply uses a 10-A AC power
c04111585 — DA – 13805 Worldwide — Version 35 — July 3, 2014
Page 75
QuickSpecs
HP 7500 Switch Series
Accessory Product Details
Services
HP 7502 Fabric Module
(JD196A)
Ports
Physical characteristics
Services
HP 7502 TAA-compliant
Main Processing Unit
(JC697A)
Ports
Physical characteristics
Services
HP 7500 4-port 40GbE
QSFP+ SC Module
(JC792A)
HP 7500 4-port 40GbE
CFP SC Module (JG373A)
Physical characteristics
cable
Refer to the HP website at www.hp.com/networking/services for details on
the service-level descriptions and product numbers. For details about
services and response times in your area, please contact your local HP
sales office.
1 RJ-45 dual-personality port; One console port, used for local or remote
configuration and management
1 RJ-45 autosensing 10/100 port (IEEE 802.3 Type 10BASE-T, IEEE 802.3u
Type 100BASE-TX); Duplex: half or full
1 Compact Flash port
Dimensions
7.83(w) x 13.98(d) x 1.77(h) in
(19.9 x 35.5 x 4.5 cm)
Weight
2.98 lb. (1.35 kg)
Refer to the HP website at www.hp.com/networking/services for details on
the service-level descriptions and product numbers. For details about
services and response times in your area, please contact your local HP
sales office.
1 RJ-45 dual-personality port; One console port, used for local or remote
configuration and management
1 RJ-45 autosensing 10/100 port (IEEE 802.3 Type 10BASE-T, IEEE 802.3u
Type 100BASE-TX); Duplex: half or full
1 Compact Flash port
Dimensions
13.98(d) x 7.83(w) x 1.77(h) in. (35.5 x 19.9 x
4.5 cm)
Weight
2.98 lb. (1.35 kg)
Refer to the HP website at: www.hp.com/networking/services for details
on the service-level descriptions and product numbers. For details about
services and response times in your area, please contact your local HP
sales office.
Dimensions
Services
10.08(w) x 11.73(d) x 1.57(h) in (25.6 x 29.8 x 4
cm)
Weight
6.88 lb (3.12 kg)
Refer to the HP website at: www.hp.com/networking/services for details on
the service-level descriptions and product numbers. For details about
services and response times in your area, please contact your local HP
sales office.
Physical characteristics
Dimensions
Services
16.77(w) x 11.73(d) x 1.57(h) in (42.6 x 29.8 x 4
cm)
Weight
7.63 lb (3.46 kg))
Refer to the HP website at: www.hp.com/networking/services for details
on the service-level descriptions and product numbers. For details about
services and response times in your area, please contact your local HP
sales office.
c04111585 — DA – 13805 Worldwide — Version 35 — July 3, 2014
Page 76
QuickSpecs
HP 7500 Switch Series
Summary of Changes
Date
03-Jul-2014
10-Jun-2014
15-Apr-2014
31-Mar-2014
19-Mar-2014
22-Nov-2013
14-Oct-2013
30-Sep-2013
Version History
From Version 34 to
35
From Version 33 to
34
From Version 30 to
33
From Version 29 to
30
From Version 28 to
29
From Version 27 to
28
Action
Changed
Description of Change:
Configuration menu updated.
Changed
Switch Enclosure Options were updated in the
Configuration section.
Minor edit was made in Product Overview.
From Version 26 to
27
From Version 25 to
26
Changed
Changed
Changed
Changed
Changed
Changed
Configuration Rules was revised throughout
Configuration.
Transceivers were revised in Configuration.
Box Level Integration CTO Models, Rack Level Integration
CTO Models, and Internal Power Supplies were revised in
Configuration.
Configuration was revised, including adding a new
Transceiver.
Configuration was revised.
Features and Benefits was revised.
27-Sep-2013
11-Sep-2013
19-Aug-2013
12-Jul-2013
19-Jun-2013
07-Jun-2013
22-May-2013
12-Apr-2013
From Version 24 to
25
From Version 23 to
24
From Version 22 to
23
From Version 21 to
22
From Version 20 to
21
Changed
Product overview was revised.
Configuration was revised.
Changed
Minor edit was made in Configuration.
Changed
Box Level Integration CTO Models and Rack Level
Integration CTO Models were revised in Configuration.
Updated the Configuration Information.
From Version 19 to
20
From Version 18 to
19
From Version 17 to
18
Changed
Changed
Changed
Changed
Integration was revised in Features and Benefits
Updated the Direct Attach Copper Cables in the
Configuration Information section.
Updated the Configuration Information.
Removed
Completely removed Accessories section.
Changed
19-Mar-2013
01-Mar-2013
19-Feb-2013
From Version 16 to
17
From Version 15 to
16
From Version 13 to
15
HP 10500/7500 20G Unified Wired-WLAN Module was
added to Accessory Product Details
Changed
Changed
Added
Changed
Accessory Product Details: Removed several sections.
Configuration: Completely updated Build To Order
section.
Corrected the new Configuration section.
Corrected the formatting in the new Configuration
section.
Added the Configuration section.
Changes were made to Features and Benefits. The model
specifications had minor updates, as did the Accessories
section.
c04111585 — DA – 13805 Worldwide — Version 35 — July 3, 2014
Page 77
QuickSpecs
HP 7500 Switch Series
Summary of Changes
04-Dec-2012
From Version 12 to
13
Changed
24-Sep-2012
Changed
02-Apr-2012
26-Mar-2012
16-Nov-2011
26-Sep-2011
From Version 11 to
12
y 21, 2012- From
Version 10 to 11
y 14, 2012- From
Version 9 to 10
From Version 8 to 9
From Version 7 to 8
From Version 6 to 7
From Version 5 to 6
Changed
Changed
Changed
Changed
07-Sep-2011
07-Mar-2011
From Version 4 to 5
From Version 3 to 4
Added
Changed
18-Feb-2011
From Version 2 to 3
Changed
08-Oct-2010
From Version 1 to 2
Changed
Changed
Changed
Changes were made to Features and Benefits. The model
specifications had minor updates, as did the Accessories
section.
Updated Features and Benefits, Introduction, the
specifications, and Accessories.
Updated the Standards and protocols section of Technical
specifications.
Features and Benefits, Accessories, and the weight and
dimensions for each spec were revised.
Part number was revised.
Accessories were revised.
Specifications were revised.
Models, Features and Benefits and Accessories were
revised.
Accessory Product Details was added.
Accessories product descriptions and notes and services
in Models were revised.
Clarified in a couple of locations about the availability of
IRF.
Corrected the options section.
c04111585 — DA – 13805 Worldwide — Version 35 — July 3, 2014
Page 78
QuickSpecs
HP 7500 Switch Series
Summary of Changes
To learn more, visit: www.hp.com/networking
© Copyright 2010-2014 Hewlett-Packard Development Company, L.P. The information contained herein is subject to change
without notice. The only warranties for HP products and services are set forth in the express warranty statements accompanying
such products and services. Nothing herein should be construed as constituting an additional warranty. HP shall not be liable for
technical or editorial errors or omissions contained herein.
c04111585 — DA – 13805 Worldwide — Version 35 — July 3, 2014
Page 79
Download PDF
Similar pages