Spectra 1759EX - System Programming Guide

1759EX
SYSTEM PROGRAMMING G UIDE
Software Version 1.0
DEFAULT INSTALLER CODE
0000 / 000000 (see section [281] on page 18)
DEFAULT SYSTEM MASTER CODE
1234 / 123456 (see section [301] on page 18)
HOW DO I ENTER PROGRAMMING MODE?
STEP
STEP
STEP
STEP
1:
2:
3:
4:
Press [ E N TE R ]
Enter your [IN S T A LL E R C O D E ]
Enter 3-digit [S E CT IO N ] you wish to program
Enter required [D A T A]
DECIMAL AND HEXADECIMAL PROGRAMMING TABLE
What Do I See?
What Do I
Press?
10-Zone LED
16-Zone LED
LCD
Values 1 to 9
A (hexa only)
B (hexa only)
[1] to [9]
[0]
[1] to [9]
[0 (10)]
[ST AY]
[STAY ]
[1] to [9]
[10]
[11]
[1] to [9]
0
B
C (hexa only)
[BYP ]
[BYP ]
[12]
C
D (hexa only)
[MEM ]
[M EM ]
[13]
D
E (hexa only)
[TBL ] / [TRBL ]
[T BL ]
[14]
E
F (hexa only)
[PG ] / [F NC1]
[15]
F
Exit Without Saving
[C LEAR ]
[PG ]
[E NT E R] flashes
Erase Current Digit
[FORC E]
Displays next digit or next section
Save Data (hexa only)
[ENT ER]
Advances to the next section
Value or Action
[A RM 1] & [ST AY 1] flash
“SECTION [
]”
TROUBLE DISPLAY
Press the [T B L ] or [T R BL ] key to view the Trouble Display. Please note that the keypad can be programmed to emit a
every 5 seconds whenever a new trouble condition has occurred. Press the [T B L] or [T R B L ] key to stop the beeping.
[1] - No Battery or Low Battery
[2] - Wireless Transmitter Low Battery
[3] - Power Failure
[4] - Bell Output Disconnected
[5] - Maximum Bell Current
[6] - Maximum Auxiliary Current
[7] - Communicator Report Failure
BEEP
[8] - Timer Loss**
[9] - Tamper or Zone Wiring Failure*
[10] - Telephone Line Monitoring Failure
[11]/[S TA Y ] - Fire Loop Trouble*
[12]/[ B YP ] - Module Loss
[13]/[ M EM ] - Wireless Transmitter Supervision Loss*
[16]/[ F OR C E ] and [ T BL ]/[ T RB L ] flashes - Keypad Fault
* press the illuminated key ([9], [ST AY ] or [ME M]) to view which zones are causing the trouble. Enter the Installer Code to clear
Tamper troubles.
** press [8] to re-program the time.
Spectra 1759EX
-1-
Programming Guide
Spectra 1759EX
-2-
Programming Guide
TABLE OF CONTENTS
DE FA U LT IN S TA LL ER COD E ................................................................................................................................................ 1
DE FA U LT S Y ST EM M AS T ER C OD E ...................................................................................................................................... 1
HOW DO I E N T ER P R OG RA MM IN G MO DE ?.......................................................................................................................... 1
DE CI MA L AN D HEXA DE C IMA L P RO GR AM MIN G TA BLE ........................................................................................................... 1
TR OU BL E DIS PLA Y ............................................................................................................................................................. 1
DA TA D ISP LAY M OD E (LED K E YPA DS ON LY ) ..................................................................................................................... 5
CON F IG UR IN G TH E 1686H, 1686V AN D 1689 KEY PAD S (V 2.0 OR H IG HE R) ......................................................................... 5
CON F IG UR IN G TH E 1686H, 1686V AN D 1689 KEY PAD S (PR IOR T O V2.0) ........................................................................... 6
ZON E P R OGR AM M IN G ........................................................................................................................................................ 6
S YST E M TIM ER S ................................................................................................................................................................ 8
P RO GR AM MA BLE OU T PU T S ................................................................................................................................................ 9
S YST E M OPT ION S ........................................................................................................................................................... 12
COM M U NI CA T ION SE TT I NGS ............................................................................................................................................. 15
RE POR T C OD ES .............................................................................................................................................................. 16
S YST E M S ET T IN GS .......................................................................................................................................................... 18
US ER COD E OPT ION S ..................................................................................................................................................... 18
RE PR OGR AM ALL M OD UL ES ............................................................................................................................................ 19
P AR AD OX M EM OR Y K E Y (PMC-3) ................................................................................................................................... 19
4-PGM O UTP UT MODULE S V2.0 ........................................................................................................... 20
PGM P R OGR A MM IN G ...................................................................................................................................................... 20
PRINTE R MODULE V2.0......................................................................................................................... 21
PGM P R OGR A MM IN G ...................................................................................................................................................... 22
C LOC K PR OGR AM M IN G ..................................................................................................................................................... 22
VOICE-AS SISTE D ARM /DISARM BUS MODULE V2.0 ................................................................................ 23
WIRELE SS E XP ANS IO N ZO NE P ROGRAMMING ......................................................................................... 24
ZON E A SS IGN ME N T ......................................................................................................................................................... 24
S ER IAL N U MB ER DISP LAY ................................................................................................................................................ 24
S IGN AL ST R EN GT H DISP LAY ............................................................................................................................................ 24
RE MOT E CON T RO L U SE R A SS IGN ME NT ............................................................................................................................ 25
B UT T ON OPT ION S ........................................................................................................................................................... 25
RE MOT E CON T RO L A S SIG NM EN T ..................................................................................................................................... 26
ZO NE EX PANS IO N BUS MO DULE S .......................................................................................................... 27
PGM P R OGR A MM IN G (SPC-ZX8 AN D APR3-ZX8 ON LY )................................................................................................. 27
USER O PE RATIO N ................................................................................................................................. 28
P AR T IT ION IN G .................................................................................................................................................................
P RO GR AM MI NG AC C ESS CODE S ......................................................................................................................................
P RO GR AM MI NG CHI ME ZO NE S .........................................................................................................................................
K EYP AD M U T IN G .............................................................................................................................................................
K EYP AD B A CK LIG HT (1686H AN D 1686V ONL Y ) ..............................................................................................................
QU IC K F U NC T ION K EYS ...................................................................................................................................................
28
28
29
29
29
29
APPE NDIX A - ADEMCO CID REP ORT CODE LIST (P RO G.)...................................................................... 30
APPE NDIX B - ADEMCO CID REP ORT CODE LIST ( ALL CO DES) .............................................................. 31
BUS MO DULE CONNE CTIO NS ................................................................................................................. 32
P RI NT E R M OD UL E (APR3-PRT1) .................................................................................................................................... 32
4-PGM OU T PU T M OD U LE (APR3-PGM4) ...................................................................................................................... 33
Spectra 1759EX
-3-
Programming Guide
4- Z ON E EX PAN SI ON BU S MOD U LE (SPC-ZX4 AN D APR3-ZX4) ....................................................................................... 33
V OIC E - ASS IST ED A RM /D IS AR M B U S M OD U LE (APR3-ADM2) ........................................................................................... 34
8-ZON E E XPA N SION B US MOD U LES (SPC-ZX8 AN D APR3-ZX8) .................................................................................... 35
HARDWARE CONNECTIONS ................................................................................................................... 36
S IN GLE ZON E IN P UT S ...................................................................................................................................................... 36
CON N EC T IN G FIR E CI RC U IT S , K EYS WIT C H ES A ND PGM S ................................................................................................. 36
A LAR M R EL AY AN D PGM C ON NE CT IO NS .......................................................................................................................... 37
CON N EC T IN G MO RE THA N TW O KE YPA D S ....................................................................................................................... 37
AC P O WER & B AC K UP BAT T E RY CON NE CT I ON S .............................................................................................................. 37
S PEC T R A 1759EX PCB L AY OU T ..................................................................................................................................... 38
Spectra 1759EX
-4-
Programming Guide
DATA DISPLAY MODE (LED Keypads Only)
View the section’s programming one digit at a time. Does not function with sections using Feature Select Programming.
CONFIGURING THE 1686H, 1686V and 1689 KEYPADS (V2.0 or higher)
The keypad’s zone number, EOL definition and tamper switch are programmed through the keypad’s programming mode. To
do so:
How Do I Configure The Keypad?
STEP 1: Press [ EN T ER ]
STEP 2: Enter your [IN S TA L L ER CO DE ] (default: 0000 / 000000)
STEP 3: Press the [P G ] (1686H/V) / [F N C 1] (1689) key and hold it for 3 seconds.
STEP 4: Press the desired key ([1] to [3]. See below)
STEP 5: Press [ EN T ER ] to exit programming mode
PLEASE NOTE: After two minutes, the keypad exits programming mode.
Key [1] - Keypad Zone Selection
Key [1] determines whether the keypad’s zone is Keypad Zone 1 or Keypad Zone 2. When key [1] is OFF (not illuminated),
the keypad’s zone is Keypad Zone 1. When key [1] is ON (illuminated), the keypad’s zone is Keypad Zone 2. Refer to the
“Zone Recognition Table” on page 6 for more information.
Key [1] OFF - Keypad Zone 1 (default)
Key [1] ON - Keypad Zone 2
Key [2] - EOL Definition
Key [2] determines the keypad zone’s EOL definition. When key [2] is OFF (not illuminated), EOL is disabled and the keypad
zone uses the on-board EOL resistor. When key [2] is ON (illuminated), EOL is enabled and the keypad zone requires that an
external EOL resistor be connected (refer to “Spectra 1759EX PCB Layout” on page 38 for more details).
Key [2] OFF - EOL disabled
Key [2] ON - EOL enabled (default)
Key [3] - On-Board Tamper
Key [3] enables or disables the keypad’s on-board tamper switch. When key [3] is OFF (not illuminated), the tamper switch is
disabled. When key [3] is ON (illuminated), the tamper switch is enabled.
Key [3] OFF - On-board tamper switch disabled
Key [3] ON - On-board tamper switch enabled
PLEASE NOTE: The keypad can be ordered with or without a tamper switch. If the keypad has no tamper
switch, key [3] will be OFF by default. If the keypad has a tamper switch, key [3] will be ON by default.
Spectra 1759EX
-5-
Programming Guide
CONFIGURING THE 1686H, 1686V and 1689 KEYPADS (Prior to V2.0)
The keypad’s zone number and EOL definition are defined through the jumpers located on the PCB board. The jumpers are
as follows:
J1 - Keypad Zone Select Jumper
Jumper J1 determines whether the keypad’s zone is Keypad Zone 1 or Keypad Zone 2. When the jumper is OFF, the
keypad’s zone is Keypad Zone 2. When the jumper is ON, the keypad’s zone is Keypad Zone 1. Refer to the “Zone
Recognition Table” on page 6 for more information.
J1 OFF - Keypad Zone 2
J1 ON - Keypad Zone 1
J2 - EOL Definition Jumper
Jumper J2 determines the keypad zone’s EOL definition. When the jumper is OFF, EOL is disabled and the keypad zone
uses the on-board EOL resistor. When the jumper is ON, EOL is enabled and the keypad zone requires that an external EOL
resistor be connected (refer to “Spectra 1759EX PCB Layout” on page 38 for more details).
J2 OFF - EOL disabled
J2 ON - EOL enabled
ZONE PROGRAMMING
When programming zones, the zone assignments are dependent on where the detection devices in the system are
connected. Do not assign inputs from different modules to the same expansion input. In installations that require using
mostly the expansion inputs, refer to Reassign Zones to Expansion Inputs (see section [126] option [8] on page 12).
Zone Recognition Table
Device connected to
which input?
Control Panel
Input 1 =
Input 2 =
Input 3 =
Input 4 =
Input 5 =
Keypad
Zone 1 =
Zone 2 =
Expansion
Input 1 =
Input 2 =
Input 3 =
Input 4 =
Input 5 =
Input 6 =
Input 7 =
Input 8 =
Spectra 1759EX
-6-
1759EX
Zone
Zone
Zone
Zone
Zone
1
2
3
4
5
Zone 6
Zone 7
Zone
Zone
Zone
Zone
Zone
Zone
Zone
Zone
8
9
10
11
12
13
14
15
Programming Guide
How Do I Program the Zones?
STEP 1: Press the [ EN T ER ] key
STEP 2: Enter the [IN ST A L L ER CO DE ] (Default: 0000 / 000000)
STEP 3: Enter 3-digit [S EC T ION ]
STEP 4: Enter one digit from the Zone Definition table
STEP 5: Enter one digit from the Partition Assignment table
STEP 6: Select one or more options from the Zone Options table
STEP 7: Press the [E NT E R] key
[FORCE] key = empty
Section
Description
Zone
Definition
Partition
Assignment
[001] = Zone 01:
[002] = Zone 02:
[003] = Zone 03:
[004] = Zone 04:
[005] = Zone 05:
[006] = Zone 06:
[007] = Zone 07:
[008] = Zone 08:
[009] = Zone 09:
[010] = Zone 10:
[011] = Zone 11:
[012] = Zone 12:
[013] = Zone 13:
[014] = Zone 14:
[015] = Zone 15:
Zone Options
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
Defaults =
Empty
Partition 1
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
3 4 5 6 7
3 4 5 6 7
3 4 5 6 7
3 4 5 6 7
3 4 5 6 7
3 4 5 6 7
3 4 5 6 7
3 4 5 6 7
3 4 5 6 7
3 4 5 6 7
3 4 5 6 7
3 4 5 6 7
3 4 5 6 7
3 4 5 6 7
3 4 5 6 7
1 and 2 ON
8
8
8
8
8
8
8
8
8
8
8
8
8
8
8
Only the control panel’s on-board inputs can be defined as a Fire, Delayed Fire or a Keyswitch zone. The onboard zones are zones 01 to 05.
Spectra 1759EX
-7-
Programming Guide
SYSTEM TIMERS
Section #
[050]
[051]
[052]
[053]
[054]
[055]
[056]
[057]
[058]
[059]
[060]
[061]
[062]
[063]
[064]
[065]
[066]
[067]
[068]
[069]
[070]
[071]
[072]
[073]
[074]
[075]
[076]
[077]
[078]
[079]
[080]
[081]
[082]
[083]
[084]
[085]
[086]
[087]
[088]
___/___/___
___/___/___
___/___/___
___/___/___
___/___/___
___/___/___
___/___/___
___/___/___
___/___/___
___/___/___
___/___/___
___/___/___
___/___/___
___/___/___
___/___/___
___/___/___
___/___/___
___/___/___
___/___/___
___/___/___
___/___/___
___/___/___
___/___/___
___/___/___
___/___/___
___/___/___
___/___/___
___/___/___
___/___/___
___/___/___
___/___/___
___/___/___
___/___/___
___/___/___
___/___/___
___/___/___
___/___/___
___/___/___
Decimal Value (000 to 255)
x 10 msec.
x 10 msec.
x 10 msec.
x 10 msec.
x 10 msec.
x 10 msec.
x 10 msec.
x 10 msec.
x 10 msec.
x 10 msec.
x 10 msec.
x 10 msec.
x 10 msec.
x 10 msec.
x 10 msec.
seconds (000 = follow Deactivation Event)
seconds (000 = follow Deactivation Event)
seconds (000 = follow Deactivation Event)
seconds
seconds
seconds
seconds
minutes (000 = no bell on alarm)
minutes (000 = no bell on alarm)
x 15 minutes (000 = disabled)
x 15 minutes (000 = disabled)
seconds (minimum 10 sec.)
(000 = no answer, maximum = 15 rings)
x 2 sec. (minimum 32 sec.)
seconds
(000 = 16, maximum = 16)
seconds
seconds
seconds (minimum 10 sec.)
seconds
minutes
days (000 = disabled)
000 to 127 = +1 to +127 seconds
128 to 255 = -1 to -127 seconds
(000 = disabled, maximum = 15)
minutes (000 = disabled)
(000 = disabled)
attempts before locking (000 = disabled)
minutes (000 = disabled)
seconds (000 = disabled)
[089]
[090]
[091]
[092]
[093]
[094]
___/___/___
___/___/___
___/___/___
___/___/___
___/___/___
___/___/___
[110]
[111]
[112]
___/___ : ___/___ hours (00 to 23) : minutes (00 to 59)
___/___ : ___/___ hours (00 to 23) : minutes (00 to 59)
___/___ : ___/___ hours (00 to 23) : minutes (00 to 59)
Spectra 1759EX
-8-
Description
Z ON E SP EED (Z ON E
Z ON E SP EED (Z ON E
Z ON E SP EED (Z ON E
Z ON E SP EED (Z ON E
Z ON E SP EED (Z ON E
Z ON E SP EED (Z ON E
Z ON E SP EED (Z ON E
Z ON E SP EED (Z ON E
Z ON E SP EED (Z ON E
Z ON E SP EED (Z ON E
Z ON E SP EED (Z ON E
Z ON E SP EED (Z ON E
Z ON E SP EED (Z ON E
Z ON E SP EED (Z ON E
Z ON E SP EED (Z ON E
FU T UR E USE
PGM 1 T I ME R
PGM 2 T I ME R
Default
600 msec.
600 msec.
600 msec.
600 msec.
600 msec.
600 msec.
600 msec.
600 msec.
600 msec.
600 msec.
600 msec.
600 msec.
600 msec.
600 msec.
600 msec.
1)
2)
3)
4)
5)
6)
7)
8)
9)
10)
11)
12)
13)
14)
15)
GL OBAL PGM T IME R
EN T R Y D ELA Y
EN T R Y D ELA Y
EX IT D E LAY
EX IT D E LAY
1
2
1
2
BE LL C U T -OF F TI ME R ( PAR T IT ION
1)
2)
(PAR T IT ION 1)
(PAR T IT ION 2)
BE LL C U T -OF F TI ME R ( PAR T IT ION
N O MO VEM EN T T IME R
N O MO VEM EN T T IME R
AN SW ER IN G M AC H IN E OVE RR ID E D EL AY
N UM BE R O F R IN GS
T LM F AIL T IM ER
D ELA Y AL AR M T R AN SM IS SION
M AXIM U M D IA LIN G AT T E MP TS
D ELA Y BE TW EE N A TT E MP TS
PAG ER DE LAY
IN T EL LIZ ON E D EL AY
R EC EN T CL OSI NG D EL AY
POW ER F AIL U RE R E POR T DE LAY
AU T O T EST R EP OR T
C LOC K A DJU ST
AU T O Z ON E SH U T DO WN CO UN T ER
R EC YC LE A LA RM D ELA Y
R EC YC LE A LA RM C OU NT E R
KE YPAD LO CK OU T
KE YPAD LO CK OU T D E LAY
PAN IC LO CK OU T T I ME R
AU T O T EST R EP OR T ( TI ME O F D AY )
AU T O -A R M T IM E (PA R TI T ION
AU T O -A R M T IM E (PA R TI T ION
Programming Guide
1)
2)
5 sec.
5 sec.
5 sec.
45 sec.
45 sec.
30 sec.
30 sec.
4 min.
4 min.
Disabled
Disabled
Disabled
8 rings
32 sec.
Disabled
8 attempts
20 sec.
5 sec.
48 sec.
No delay
15 min.
Disabled
Disabled
5
Disabled
Disabled
Disabled
Disabled
Disabled
Disabled
Disabled
Disabled
PROGRAMMABLE OUTPUTS
Each PGM Deactivation event can be used as another start (activation) event if their respective PGM timer (see sections
[066] to [068]) is programmed with a value other than 000.
Example: section [120] = 05 03 02: this means PGM1 will activate whenever partition 2 is Stay Armed.
Section #
Event Group # Sub-Group #
Partition #
[120]
[121]
PGM 1 PGM Activation Event
PGM 1 PGM Deactivation Event
___/___
___/___
___/___
___/___
___/___
___/___
[122]
[123]
PGM 2 PGM Activation Event
PGM 2 PGM Deactivation Event
___/___
___/___
___/___
___/___
___/___
___/___
[124]
[125]
Global PGM Activation Event
Global PGM Deactivation Event
Used to activate PGMs on
expansion modules & LCD keypads.
___/___
___/___
___/___
___/___
___/___
___/___
Event Group #
Sub-Group #
00 = Zone OK
01 = Zone Open
02 = Partition Status
05 = Non-Reportable Events
06 = Arm/Disarm with Remote Control
07 = Button Pressed on Remote
(see button option “B” on page 25)
08 = Button Pressed on Remote
(see button option “C” on page 25)
09 = Button Pressed on Remote
(see button option “D” on page 25)
Spectra 1759EX
01 to 15 = Zones 1 to 15
99 = Any Zone
01 to 15 = Zones 1 to 15
99 = Any Zone
00 = System not ready (Partition 1 only)
01 = System ready (Partition 1 only)
02 = Steady Alarm in Partition
03 = Pulsed Alarm in Partition
04 = Pulsed or Steady Alarm in Partition
05 = Alarm in Partition Restored
06 = Bell Squawk Activated (Partition 1 only)
07 = Bell Squawk Deactivated (Partition 1 only)
08 = Ground start (Partition 1 only )
09 = Disarm Partition
10 = Arm Partition
11 = Entry Delay (breach when system is armed)
99 = Any Sub-Group
00 = Telephone Line Trouble (Partition 1 only)
01 = [PG ] or [F N C 1] key was pressed (Partition 1 only)
02 = Instant Arming
03 = Stay Arming
04 = Force Arming
05 = Fast Exit (Force & Regular Only)
06 = PC Fail to Communicate (Partition 1 only)
07 = Midnight (Partition 1 only)
99 = Any Sub-Group (Partition 1 only, except 02 to 05)
01 to 08 = Remote Controls 1 to 8
99 = Any Remote Control
01 to 08 = Remote Controls 1 to 8
99 = Any Remote Control
01 to 08 = Remote Controls 1 to 8
99 = Any Remote Control
01 to 08 = Remote Controls 1 to 8
99 = Any Remote Control
-9-
Programming Guide
Event Group #
Sub-Group #
10 = Bypass Programming
11 = User Activated PGM
12 = Zone with Delay Transmission Option Enabled is
Breached
13 = Arm with User Code
14 = Special Arm
15 = Disarm with User Code
16 = Disarm After Alarm w/ User Code
17 = Cancel Alarm with User Code
18 = Special Disarm
19 = Zone Bypassed on Arming
20 = Zone in Alarm
21 = Fire Alarm
22 = Zone Alarm Restore
23 = Fire Alarm Restore
24 = Special Alarm
25 = Auto Zone Shutdown
26 = Zone Tamper
27 = Zone Tamper Restore
Spectra 1759EX
01 to 48 = User Code Numbers 001 to 048
99 = Any User Code
01 to 48 = User Code Numbers 001 to 048 (Partition 1 only)
99 = Any User Code
01 to 15 = Zones 1 to 15
99 = Any Zone
01 to 48 = User Code Numbers 001 to 048
99 = Any User Code
00 = Auto Arming (timed/no movement)
01 = Late to Close (Auto-Arming failed)
02 = No Movement Auto-Arming
03 = Partial Arming (Stay, Force, Instant, Bypass)
04 = One-Touch Arming
05 = Arm with WinLoad Software
99 = Any Sub-Group
01 to 48 = User Code Numbers 001 to 048
99 = Any User Code
01 to 48 = User Code Numbers 001 to 048
99 = Any User Code
01 to 48 = User Code Numbers 001 to 048
99 = Any User Code
00 = Cancel Auto Arm (timed/no movement)
01 = Disarm with WinLoad Software
02 = Disarm after alarm with WinLoad Software
03 = Cancel Alarm with WinLoad Software
99 = Any Sub-Group
01 to 15 = Zones 1 to 15
99 = Any Zone
01 to 15 = Zones 1 to 15
99 = Any Zone
01 to 05 = Zones 1 to 5 (on-board inputs)
99 = Any Zone
01 to 15 = Zones 1 to 15
99 = Any Zone
01 to 05 = Zones 1 to 5 (on-board inputs)
99 = Any Zone
00 = Emergency Panic
01 = Auxiliary Panic
02 = Fire Panic
03 = Recent Closing
04 = Auto Zone Shutdown
05 = Duress Alarm
06 = Keypad Lockout
99 = Any Sub-Group
01 to 15 = Zones 1 to 15
99 = Any Zone
01 to 15 = Zones 1 to 15
99 = Any Zone
01 to 15 = Zones 1 to 15
99 = Any Zone
- 10 -
Programming Guide
Event Group #
Sub-Group #
28 = System Trouble
29 = System Trouble Restore
30 = Special Reporting
31 = Wireless Transmitter Supervision Loss
32 = Wireless Transmitter Supervision Loss Restore
33 = Arming with a Keyswitch
34 = Disarming with a Keyswitch
35 = Disarm after Alarm with a Keyswitch
36 = Cancel Alarm with a Keyswitch
37 = Wireless Transmitter Low Battery
38 = Wireless Transmitter Low Battery Restore
Event Group #
01 = AC Loss: only after Power Failure Delay has elapsed
(Partition 1 only)
02 = Battery Failure (Partition 1 only)
03 = Auxiliary current overload (Partition 1 only)
04 = Bell current overload (Partition 1 only)
05 = Bell disconnected (Partition 1 only)
06 = Timer Loss (Partition 1 only)
07 = Fire Loop Trouble (Partition 1 only )
08 = Future Use
09 = Module Fault (Partition 1 only)
10 = Printer Fault (Partition 1 only )
11 = Fail to Communicate (Partition 1 only)
99 = Any Sub-Group (Partition 1 only)
00 = TLM restore (Partition 1 only)
01 = AC Loss restore (Partition 1 only)
02 = Battery Failure restore (Partition 1 only)
03 = Auxiliary current overload restore (Partition 1 only)
04 = Bell current overload restore (Partition 1 only)
05 = Bell disconnected restore (Partition 1 only)
06 = Timer Programmed (Partition 1 only)
07 = Fire Loop Trouble restore (Partition 1 only)
08 = Future Use
09 = Module Fault restore (Partition 1 only)
10 = Printer Fault restore (Partition 1 only)
11 = Fail to Communicate restore (Partition 1 only)
99 = Any Trouble Restore (Partition 1 only)
00 = System Power Up (Partition 1 only)
01 = Test Report (Partition 1 only)
02 = WinLoad Software Access (Partition 1 only)
03 = WinLoad Software Access finished (Partition 1 only)
04 = Installer enters programming mode (Partition 1 only)
05 = Installer exits programming mode (Partition 1 only )
99 = Any Sub-Group (Partition 1 only)
01 to 15 = Zones 1 to 15
99 = Any Zone
01 to 15 = Zones 1 to 15
99 = Any Zone
01 to 05 = Zones 1 to 5 (on-board inputs)
99 = Any Zone
01 to 05 = Zones 1 to 5 (on-board inputs)
99 = Any Zone
01 to 05 = Zones 1 to 5 (on-board inputs)
99 = Any Zone
01 to 05 = Zones 1 to 5 (on-board inputs)
99 = Any Zone
01 to 15 = Zones 1 to 15
99 = Any Zone
01 to 15 = Zones 1 to 15
99 = Any Zone
Sub-Group #
Partition #
80 = PGM follows Clock (APR3=PGM4 only) HH = hour according to 24hr. clock MM = minutes according to 24hr. clock
Spectra 1759EX
- 11 -
Programming Guide
SYSTEM OPTIONS
Bold = Default Setting
SECTION [126]: General Options
Option
[1]
[2]
[3]
[4]
[5]
[6]
[7]
[8]
OFF
N Disabled
N Enter Access Code
N 2 minutes
N Normally Open (N.O.)
N Normally Open (N.O.)
N Normally Open (N.O.)
N Disabled
N Disabled
Confidential Mode
To exit Confidential Mode
Confidential Mode timer
PGM1 normal state
PGM2 normal state
Global PGM normal state
Reassign Keypad Zone 2
Reassign zones to expansion inputs*
ON
N Enabled
N Press a Key
N 5 seconds
N Normally Closed (N.C.)
N Normally Closed (N.C.)
N Normally Closed (N.C.)
N Enabled
N Enabled
* Reassign Zones to Expansion Inputs changes the zone numbering to increase the number of expansion inputs that can be
displayed on 10-Zone LED Keypads. Refer to Spectra 1759EX Reference & Installation Manual for details.
SECTION [127]: General Options
Option
[1]
[2]
[3]
[4]
[5]
[6]
[7]
[8]
Partitioning
Access code length
Keypad audible trouble warning
Lock System Master Code
Battery charge current
User Code 048 is a Duress Code
Alarm relay follows
Future use
OFF
N Disabled
N 6-digits
N Disabled
N Disabled
N 350mA
N Disabled
N Bell Output
N N/A
ON
N Enabled
N 4-digits
N Enabled
N Enabled
N 700mA
N Enabled
N Global PGM
N N/A
OFF
N Disabled
N Disabled
N Disabled
N Silent
N Silent
N Silent
N Disabled
N Disabled
ON
N Enabled
N Enabled
N Enabled
N Audible
N Audible
N Fire
N Enabled
N Enabled
OFF
N Steady
N Disabled
N Disabled
N Disabled
N N/A
N Disabled
N Disabled
N Disabled
ON
N Pulse (flash)
N Enabled
N Enabled
N Enabled
N N/A
N Enabled
N Enabled
N Enabled
SECTION [128]: General Options
Option
[1]
[2]
[3]
[4]
[5]
[6]
[7]
[8]
Panic 1: keys [1] & [3]
Panic 2: keys [4] & [6]
Panic 3: keys [7] & [9]
Panic 1: silent or audible
Panic 2: silent or audible
Panic 3: silent or fire
Keypad 1 tamper supervision
Keypad 2 tamper supervision
SECTION [129]: General Options
Option
[1]
[2]
[3]
[4]
[5]
[6]
[7]
[8]
PGM2 output activation option
PGM2 pulse once every 30 sec. if system armed
PGM2 pulse on Arm, twice on Disarm
ZX4 & ZX8 zone expansion module supervision
Future use
Wireless module low battery supervision
4-PGM Output Module supervision (APR3-PGM4)
Printer Module supervision (APR3-PRT1)
Spectra 1759EX
- 12 -
Programming Guide
Bold = Default Setting
SECTION [130]: Arming/Disarming Options
Option
[1]
[2]
[3]
[4]
[5]
[6]
[7]
[8]
One-touch Regular Arming
One-touch Stay Arming
One-touch Force Arming
One-touch bypass programming
Restrict arming on battery failure
Restrict arming on Tamper failure
Bell Squawk on Arm/Disarm with keypad
Beep on exit delay
OFF
N Disabled
N Disabled
N Disabled
N Disabled
N Disabled
N Disabled
N Disabled
N Disabled
ON
N Enabled
N Enabled
N Enabled
N Enabled
N Enabled
N Enabled
N Enabled
N Enabled
OFF
N Always
N Disabled
N Disabled
ON
N Only after alarm
N Enabled
N Enabled
N Disabled
N Disabled
N Enabled
N Enabled
N Disabled
N Enabled
N Yes
N No
N N/A
N N/A
OFF
N see table
N see table
ON
N see table
N see table
N Yes
N No EOL
N N/A
N On Bell Cut-off
N see table
N see table
N
N
N
N
N
N
SECTION [131]: Arming/Disarming Options
Option
[1]
[2]
[3]
[4]
[5]
[6]
[7]
[8]
Report Disarming
Regular Arming switches to Force Arming
Bell Squawk on Arm/Disarm with remote control
(must be enabled for UL installations)
No exit delay when Arming with a remote control
No exit delay beeps and no Bell Squawk when
Stay Arming
Restrict arming on wireless transmitter
supervision loss
Generate supervision loss if detected on
bypassed wireless zone
Future Use
SECTION [132]: Zone Options
Option
[1]&[2]
[3]
[4]
[5]
[6]
[7]&[8]
Tam per Reco gnitio n Options
[1]
[2]
O FF
O FF
O FF
ON
ON
O FF
ON
ON
Disabled (default)
When disarmed: GE NE RAT E S T ROUB LE ONLY
When armed: Follows Z one Alarm Types
When disarmed: GE NE RAT E S S I LENT AL ARM
When armed: Follows Z one Alarm Types
When disarmed: GE NE RAT E S A UDI BLE A LA RM
When armed: Follows Z one Alarm Types
Generate tamper if detected on bypassed zone
EOL (end-of-line) resistors
Future use
Report zone restore
Wireless Transmitter Sup ervision Optio ns
[7]
[8]
O FF
O FF
O FF
ON
ON
O FF
ON
ON
Disabled (default)
When disarmed: GE NE RAT E S T ROUB LE ONLY
When armed: Follows Z one Alarm Types
When disarmed: GE NE RAT E S S I LENT AL ARM
When armed: Follows Z one Alarm Types
When disarmed: GE NE RAT E S A UDI BLE A LA RM
When armed: Follows Z one Alarm Types
Spectra 1759EX
- 13 -
Programming Guide
No
Use EOL Resistors
N/A
On Zone Closure
see table
see table
Bold = Default Setting
SECTION [133]: Par tition 1 Options
Option
[1]
[2]
[3]
[4]
[5]
[6] to [8]
OFF
N Disabled
N Disabled
N Regular Arming
N Disabled
N Disabled
N N/A
ON
N Enabled
N Enabled
N Stay Arming
N Enabled
N Enabled
N N/A
OFF
Auto-arm on time
N Disabled
Auto-arm on no movement
N Disabled
Auto Arming = Regular or Stay
N Regular Arming
Switch to Stay Arming if no entry delay is opened N Disabled
Stay Arming with Delay Partition 2 (Delay = [070]) N Disabled
Future use
N N/A
ON
N Enabled
N Enabled
N Stay Arming
N Enabled
N Enabled
N N/A
Auto-arm on time
Auto-arm on no movement
Auto Arming = Regular or Stay
Switch to Stay Arming if no entry delay is opened
Stay Arming with Delay Partition 1 (Delay = [070])
Future use
SECTION [134]: Partition 2 Options
Option
[1]
[2]
[3]
[4]
[5]
[6] to [8]
SECTION [135]: Dialer Options
Option
[1] & [2]
[3]
[4]
[5]
[6]
[7] & [8]
Teleph one Lin e Mon itoring (TLM) Optio ns
[1]
[2]
O FF
O FF
O FF
ON
ON
O FF
ON
ON
OFF
N see table
N see table
ON
N see table
N see table
N Disabled
N Pulse Dialing
N 1:2
N Disabled
N N/A
N
N
N
N
N
OFF
N Disabled
N Disabled
N Programmable
N Disabled
N Continue after 4 sec.
N see table
N see table
ON
N Enabled
N Enabled
N All Codes (automatic)
N Enabled
N Hang-up after 16 sec.
N see table
N see table
N N/A
N N/A
TLM Disabled (default)
TLM generates a trouble if armed
TLM generates an audible alarm if armed
Silent alarms become audible
Reporting (Dialer)
Dialing method
Pulse ratio
If armed, activate bell output on Com. Failure
Future use
Enabled
Tone (DTMF) Dialing
1:1.5
Enabled
N/A
SECTION [136]: Dialer Options
Option
[1]
[2]
[3]
[4]
[5]
[6]&[7]
[8]
Call back WinLoad
Automatic event buffer transmission
Contact I.D. report codes
Alternate dial
If no dial tone is present
Pag er Repo rting Fo rm at Dialer Option s
[6]
[7]
O FF
O FF
O FF
ON
2 calls to pager or cellular telephone
ON
O FF
3 calls to pager or cellular telephone
ON
ON
4 calls to pager or cellular telephone
1 call to pager o r cellular telepho ne (default)
Future use
Spectra 1759EX
- 14 -
Programming Guide
Bold = Default Setting
SECTION [137]: Event Call Direction
Option
[1]
[2]
[3]
[4]
[5]
[6]
[7] & [8]
Call Telephone
Call Telephone
Call Telephone
Call Telephone
Call Telephone
Call Telephone
Future use
#1
#2
#1
#2
#1
#2
for Arming/Disarming Report Codes
for Arming/Disarming Report Codes
for Alarm/Restore Report Codes
for Alarm/Restore Report Codes
for Tamper/Restore Report Codes
for Tamper/Restore Report Codes
OFF
N Disabled
N Disabled
N Disabled
N Disabled
N Disabled
N Disabled
N N/A
ON
N Enabled
N Enabled
N Enabled
N Enabled
N Enabled
N Enabled
N N/A
OFF
N Disabled
N Disabled
N Disabled
N Disabled
N N/A
ON
N Enabled
N Enabled
N Enabled
N Enabled
N N/A
SECTION [138]: Event Call Direction
Option
[1]
[2]
[3]
[4]
[5] to [8]
Call Telephone
Call Telephone
Call Telephone
Call Telephone
Future use
#1
#2
#1
#2
for Trouble/Restore Report Codes
for Trouble/Restore Report Codes
for Special Report Codes
for Special Report Codes
COMMUNICATION SETTINGS
Section #
[140]
___ / ___
R EP OR TI NG F O RM AT S
1 = AD EM C O SL OW (1400HZ , 1900HZ, 10BPS )
2 = SI LEN T KN IGH T F AST (1400HZ , 1900HZ, 20BPS)
3 = SE SC OA (2300HZ , 1800HZ, 20BPS )
4 = AD EM C O EX PR ESS (D TMF 4+2)
5 = A D EM CO C ON T AC T ID (D EF A U LT ) A LS O , S EE OP T ION [3] I N S EC T ION [136]
6 = PA GER F OR MA T
If Hexadecimals (0 to FF) are used to program the report codes, verify that the pager also supports
Hexadecimals. If the pager does not support Hexadecimals, use only the digits 0 to 9.
T EL 1 T EL 2
[141]
[142]
[143]
[144]
___/___/___/___
___/___/___/___
___/___/___/___
___/___/___/___
[150]
__/__/__/__/__/__/__/__/__/__/__/__/__/__/__/__/__/__/__/__/__/__/__/__/__/__/__/__/__/__/__/__
PC T EL EPH ON E N U MB ER FO R W IN LOA D S OF T WA RE (32-digits, if less than 32 press [E NT E R] to accept)
[151]
PA NE L ID EN T IF IE R (W IN LO AD SOF T WA R E )
PC PAS SW OR D ( WIN L OAD SOF T W AR E )
1 (For less than 4 digits, use the [F OR C E ] key to enter blanks.)
PA RT IT I ON A CC OU N T N U M BER 2 (For less than 4 digits, use the [F OR C E ] key to enter blanks.)
PA RT IT I ON A CC OU N T N U M BER
__/__/__/__/__/__/__/__/__/__/__/__/__/__/__/__/__/__/__/__/__/__/__/__/__/__/__/__/__/__/__/__
1 (32-digits, if less than 32 press [EN TER] to accept)
C EN T R AL ST A T ION T EL EPH ON E O R PA GER N U MB ER
[152]
[153]
__/__/__/__/__/__/__/__/__/__/__/__/__/__/__/__/__/__/__/__/__/__/__/__/__/__/__/__/__/__/__/__
C EN T R AL ST A T ION T EL EPH ON E O R PA GER N U MB ER 2 (32-digits, if less than 32 press [EN TER ] to accept)
__/__/__/__/__/__/__/__/__/__/__/__/__/__/__/__/__/__/__/__/__/__/__/__/__/__/__/__/__/__/__/__
(32-digits, if less than 32 press [EN T ER ] to accept)
BA C K UP TE LE PH ON E NU M BE R
[ST A Y ] = *
[B YP ] = #
Special Keys for Telephone Numbers
[M EM ] = Switch from pulse to tone dialing or vice versa
[F OR C E ] = Delete current digit
[T B L ] or [T RB L ] = 4-second pause
[PG ] or [ FN C 1] = Inserts Blank Space
Spectra 1759EX
- 15 -
Programming Guide
REPORT CODES
Ademco Slow, Silent Knight, SESCOA, Ademco Express and Pager Formats: Enter the desired 1- or 2-digit hexa-value
(0-F or 00-FF). Ademco “Programmable” Format: Enter the desired 2-digit hexa values from the “Ademco Report Code
List - Programmable” (see Appendix A on page 30). Also Note that entering FF will set the report code to the default Ademco
Report Code. Ademco “All Codes” Format: The control panel automatically generates report codes from the “Ademco
Report Code List - All Codes” (see Appendix B on page 31).
ARMING REPORT CODES
[160]___/___Access
___/___Access
___/___Access
___/___Access
Code
Code
Code
Code
01
02
03
04
[165]___/___Access
___/___Access
___/___Access
___/___Access
Code 21
Code 22
Code 23
Code 24
[170]___/___Access
___/___Access
___/___Access
___/___Access
Code 41
Code 42
Code 43
Code 44
[161]___/___Access
___/___Access
___/___Access
___/___Access
Code
Code
Code
Code
05
06
07
08
[166]___/___Access
___/___Access
___/___Access
___/___Access
Code 25
Code 26
Code 27
Code 28
[171]___/___Access
___/___Access
___/___Access
___/___Access
Code 45
Code 46
Code 47
Code 48
[162]___/___Access
___/___Access
___/___Access
___/___Access
Code
Code
Code
Code
09
10
11
12
[167]___/___Access
___/___Access
___/___Access
___/___Access
Code 29
Code 30
Code 31
Code 32
SPECIAL ARMING CODES
[163]___/___Access
___/___Access
___/___Access
___/___Access
Code
Code
Code
Code
13
14
15
16
[168]___/___Access
___/___Access
___/___Access
___/___Access
Code 33
Code 34
Code 35
Code 36
[172]___/___Auto-Arming
___/___Late to Close
___/___No Movement
___/___Partial Arming
[164]___/___Access
___/___Access
___/___Access
___/___Access
Code
Code
Code
Code
17
18
19
20
[169]___/___Access
___/___Access
___/___Access
___/___Access
Code 37
Code 38
Code 39
Code 40
[173]___/___Quick Arming
___/___Arming via PC
___/___Keyswitch Arming
___/___N/A
DISARMING REPORT CODES
[174]___/___Access
___/___Access
___/___Access
___/___Access
Code
Code
Code
Code
01
02
03
04
[179]___/___Access
___/___Access
___/___Access
___/___Access
Code 21
Code 22
Code 23
Code 24
[184]___/___Access
___/___Access
___/___Access
___/___Access
Code 41
Code 42
Code 43
Code 44
[175]___/___Access
___/___Access
___/___Access
___/___Access
Code
Code
Code
Code
05
06
07
08
[180]___/___Access
___/___Access
___/___Access
___/___Access
Code 25
Code 26
Code 27
Code 28
[185]___/___Access
___/___Access
___/___Access
___/___Access
Code 45
Code 46
Code 47
Code 48
[176]___/___Access
___/___Access
___/___Access
___/___Access
Code
Code
Code
Code
09
10
11
12
[181]___/___Access
___/___Access
___/___Access
___/___Access
Code 29
Code 30
Code 31
Code 32
SPECIAL DISARMING CODES
[177]___/___Access
___/___Access
___/___Access
___/___Access
Code
Code
Code
Code
13
14
15
16
[182]___/___Access
___/___Access
___/___Access
___/___Access
Code 33
Code 34
Code 35
Code 36
[186]___/___Cancel Auto-Arm
___/___Disarming via PC
___/___Keyswitch Disarm
___/___N/A
[178]___/___Access
___/___Access
___/___Access
___/___Access
Code
Code
Code
Code
17
18
19
20
[183]___/___Access
___/___Access
___/___Access
___/___Access
Code 37
Code 38
Code 39
Code 40
Spectra 1759EX
- 16 -
Programming Guide
ALARM REPORT CODES
ALARM
RESTORE
SPECIAL
[187]___/___Zone 01
___/___Zone 02
___/___Zone 03
___/___Zone 04
[191]___/___Zone 01
___/___Zone 02
___/___Zone 03
___/___Zone 04
[195]___/___Emergency Panic
___/___Auxiliary Panic
___/___Fire Panic
___/___Recent Closing
[188]___/___Zone 05
___/___Zone 06
___/___Zone 07
___/___Zone 08
[192]___/___Zone 05
___/___Zone 06
___/___Zone 07
___/___Zone 08
[196]___/___Zone Shutdown
___/___Duress
___/___Keypad Lockout
___/___N/A
[189]___/___Zone 09
___/___Zone 10
___/___Zone 11
___/___Zone 12
[193]___/___Zone 09
___/___Zone 10
___/___Zone 11
___/___Zone 12
[190]___/___Zone 13
___/___Zone 14
___/___Zone 15
___/___N/A
[194]___/___Zone 13
___/___Zone 14
___/___Zone 15
___/___N/A
TAMPER REPORT CODES
TROUBLE
[197] ___/___Zone 01
___/___Zone 02
___/___Zone 03
___/___Zone 04
[200]___/___Zone 13
___/___Zone 14
___/___Zone 15
___/___N/A
[203]___/___Zone 09
___/___Zone 10
___/___Zone 11
___/___Zone 12
[198]___/___Zone 05
___/___Zone 06
___/___Zone 07
___/___Zone 08
RESTORE
[201] ___/___Zone 01
___/___Zone 02
___/___Zone 03
___/___Zone 04
[204]___/___Zone 13
___/___Zone 14
___/___Zone 15
___/___N/A
[199]___/___Zone 09
___/___Zone 10
___/___Zone 11
___/___Zone 12
[202]___/___Zone 05
___/___Zone 06
___/___Zone 07
___/___Zone 08
SYSTEM TROUBLE REPORT CODES
SYSTEM TROUBLE
RESTORE
SPECIAL
[205]___/___N/A
___/___AC Failure
___/___Battery Failure
___/___Auxiliary Supply
[208]___/___TLM
___/___AC Failure
___/___Battery Failure
___/___Auxiliary Supply
[211]___/___Cold Start (Shutdown)
___/___Test Report
___/___N/A
___/___PC Exit
[206]___/___Bell Output Overload
___/___Bell Output Disconnect
___/___Timer Loss
___/___Fire Loop Trouble
[209]___/___Bell Output Overload
___/___Bell Output Disconnect
___/___Timer Loss
___/___Fire Loop Trouble
[212]___/___Installer In
___/___Installer Out
___/___N/A
___/___N/A
[207]___/___Wireless Low Battery
___/___Module Fault
___/___Printer Fault
___/___Fail to Communicate
[210]___/___Wireless Low Battery
___/___Module Fault
___/___Printer Fault
___/___Fail to Communicate
[213]___/___TX Supervision Loss
___/___TX Supervision Restore
___/___N/A
___/___N/A
Spectra 1759EX
- 17 -
Programming Guide
SYSTEM SETTINGS
Section #
Description
[280]
___/___:___/___
SYS TE M R EA L T IM E C LOC K (H H : MM )
[281]
___/___/___/___/___/___
IN ST ALL ER C OD E , D E FA U L T :
[282]
___/___/___
IN ST ALL ER C OD E LOC K , D EF A U LT :
000 (147
[301]
___/___/___/___/___/___
SYS TE M M AS TE R C OD E , D EF A U LT :
1234 / 123456
0000 / 000000
T O LOC K ,
000 T O
U N LOC K )
USER CODE OPTIONS
System Master Code arms or disarm partitions using any arming method and can create, modify or delete any User Access
Code. Only the System Master Code can modify or delete User Access Codes assigned to both partitions.
Master Code 1 is permanently assigned to partition 1 and can be used to create, modify or delete User Access Codes that
are assigned to partition 1.
Master Code 2 is permanently assigned to partition 2 (except when partitioning is disabled, Master Code 2 will be assigned
to partition 1) and can be used to create, modify or delete User Access Codes that are assigned to the same partition.
Default for all user codes is options [1], [3] and [4] ON . [1] ON
ON = Option Enabled
[2] ON
OFF = Option Disabled
[3] ON
[4] ON
User Code Options (ON/OFF )
Section #
=
=
=
=
Partition 1 Access
Partition 2 Access
Bypass Programming
Stay Arming
[5]
[6]
[7]
[8]
ON
ON
ON
ON
=
=
=
=
Force Arming
Arm Only
PGM Activation Only
Future Use
User Code Options ( ON/OFF)
Section
[302]
Master Code 1
1 2 3 4 5 6 7 8
[325]
User Code 025
1 2 3 4 5 6 7 8
[303]
Master Code 2
1 2 3 4 5 6 7 8
[326]
User Code 026
1 2 3 4 5 6 7 8
[304]
User Code 004
1 2 3 4 5 6 7 8
[327]
User Code 027
1 2 3 4 5 6 7 8
[305]
User Code 005
1 2 3 4 5 6 7 8
[328]
User Code 028
1 2 3 4 5 6 7 8
[306]
User Code 006
1 2 3 4 5 6 7 8
[329]
User Code 029
1 2 3 4 5 6 7 8
[307]
User Code 007
1 2 3 4 5 6 7 8
[330]
User Code 030
1 2 3 4 5 6 7 8
[308]
User Code 008
1 2 3 4 5 6 7 8
[331]
User Code 031
1 2 3 4 5 6 7 8
[309]
User Code 009
1 2 3 4 5 6 7 8
[332]
User Code 032
1 2 3 4 5 6 7 8
[310]
User Code 010
1 2 3 4 5 6 7 8
[333]
User Code 033
1 2 3 4 5 6 7 8
[311]
User Code 011
1 2 3 4 5 6 7 8
[334]
User Code 034
1 2 3 4 5 6 7 8
[312]
User Code 012
1 2 3 4 5 6 7 8
[335]
User Code 035
1 2 3 4 5 6 7 8
[313]
User Code 013
1 2 3 4 5 6 7 8
[336]
User Code 036
1 2 3 4 5 6 7 8
[314]
User Code 014
1 2 3 4 5 6 7 8
[337]
User Code 037
1 2 3 4 5 6 7 8
[315]
User Code 015
1 2 3 4 5 6 7 8
[338]
User Code 038
1 2 3 4 5 6 7 8
[316]
User Code 016
1 2 3 4 5 6 7 8
[339]
User Code 039
1 2 3 4 5 6 7 8
[317]
User Code 017
1 2 3 4 5 6 7 8
[340]
User Code 040
1 2 3 4 5 6 7 8
[318]
User Code 018
1 2 3 4 5 6 7 8
[341]
User Code 041
1 2 3 4 5 6 7 8
[319]
User Code 019
1 2 3 4 5 6 7 8
[342]
User Code 042
1 2 3 4 5 6 7 8
[320]
User Code 020
1 2 3 4 5 6 7 8
[343]
User Code 043
1 2 3 4 5 6 7 8
[321]
User Code 021
1 2 3 4 5 6 7 8
[344]
User Code 044
1 2 3 4 5 6 7 8
[322]
User Code 022
1 2 3 4 5 6 7 8
[345]
User Code 045
1 2 3 4 5 6 7 8
[323]
User Code 023
1 2 3 4 5 6 7 8
[346]
User Code 046
1 2 3 4 5 6 7 8
[324]
User Code 024
1 2 3 4 5 6 7 8
[347]
User Code 047
1 2 3 4 5 6 7 8
[348]
User Code 048
1 2 3 4 5 6 7 8
Spectra 1759EX
- 18 -
Programming Guide
REPROGRAM ALL MODULES
[750]
After removing an expansion module from the communication bus, the control panel keeps the module’s
programmed sections in memory. Therefore, if you add or replace a module you can re-program the module with the
settings saved in the control panel. To do so, enter section [750] and press [E NT E R]. The keypads will beep twice
every second until the procedure is completed.
PARADOX MEMORY KEY (PMC-3)
[900]
[902]
D OW NL OAD F R OM PA RA D OX M EM OR Y KEY T O D ES T IN AT ION C ON T RO L PAN EL .
C OPY T O M EM OR Y KE Y F R OM S OU RC E C ON T R OL PA NE L.
Download to DESTINATION Control Panel
1) Remove AC and battery power from the control panel.
2) Insert the Memory Key onto the serial connector labelled KEY on the Spectra control panel to
which you wish to download the contents of the memory key to.
3) Re-apply AC and battery power.
4) Enter installer programming mode, enter section [900], then press [ EN T ER ] to acknowledge.
5) When the keypad emits a “confirmation beep”, remove the Memory Key.
6) Enter section [750] to reprogram the modules with the information downloaded from the
Paradox Memory Key.
Copy to Memory Key from SOURCE Control Panel
1) Remove AC and battery power from the control panel.
2) Insert Memory Key onto the serial connector labelled KEY on the Spectra control panel that
you want to copy. Make sure the write protect jumper of the Memory Key is on.
3) Re-apply AC and battery power.
4) Enter installer programming mode, enter section [902], then press [ EN T ER ] to acknowledge.
5) When the keypad emits a Confirmation Beep, remove the Memory Key. Remove the
Memory Key’s jumper if you do not wish to accidentally overwrite its contents.
Spectra 1759EX
- 19 -
Programming Guide
4-PGM OUTPUT MODULES V2.0
Due to the APR3-PGM4’s Auto-recognition feature, it can be used with either the Spectra (V2.0 or higher), Digiplex or
DigiplexNE control panel. When connected to the bus, the APR3-PGM4 automatically detects which control panel it is
connected to and adjusts its internal communication parameters to function accordingly. Only one APR3-PGM4 can be
connected to each Spectra control panel.
Modules with the APR- prefix are compatible with Spectra (versions 2.0 and higher) and Digiplex. Modules with the
APR3- prefix are compatible with Spectra (versions 2.0 and higher), Digiplex and DigiplexNE.
Bold = Default Setting
SECTION [500]: GENERAL OPTIONS
Option
[1]
[2]
[3]
[4]
[5]
[6]
[7]
[8]
PGM1 Time
PGM2 Time
PGM3 Time
PGM4 Time
Future use
Future use
Future use
Future use
OFF
N Seconds
N Seconds
N Seconds
N Seconds
N N/A
N N/A
N N/A
N N/A
Base Selection
Base Selection
Base Selection
Base Selection
ON
N Minutes
N Minutes
N Minutes
N Minutes
N N/A
N N/A
N N/A
N N/A
PGM PROGRAMMING
Each PGM Deactivation event can be used as another activation event if their respective PGM timer (see sections [501] to
[504]) is programmed with a value other than 000. The APR3-PGM4 uses the same PGM events as the Spectra control
panel, please refer to “Programmable Outputs” on page 9.
Section #
[501] ___/___/___
[502] ___/___/___
[503] ___/___/___
[504] ___/___/___
Decimal Value (000-255)
(000 = follow deactivation
(000 = follow deactivation
(000 = follow deactivation
(000 = follow deactivation
Description
event)
event)
event)
event)
PG M1 T I ME R
PG M2 T I ME R
PG M3 T I ME R
PG M4 T I ME R
Default Value
5 sec.
5 sec.
5 sec.
5 sec.
Section #
[505] PGM1 Activation Event
[506] PGM1 Deactivation Event
Event Group # Sub-Group #
___/___
___/___
___/___
___/___
Partition #
___/___
___/___
[507] PGM2 Activation Event
[508] PGM2 Deactivation Event
___/___
___/___
___/___
___/___
___/___
___/___
[509] PGM3 Activation Event
[510] PGM3 Deactivation Event
___/___
___/___
___/___
___/___
___/___
___/___
[511] PGM4 Activation Event
[512] PGM4 Deactivation Event
___/___
___/___
___/___
___/___
___/___
___/___
Spectra 1759EX
- 20 -
Programming Guide
PRINTER MODULE V2.0
Due to the APR3-PRT1’s Auto-recognition feature, it can be used with either the Spectra (V2.0 or higher), Digiplex or
DigiplexNE control panel. When connected to the bus, the APR3-PRT1 automatically detects which control panel it is
connected to and adjusts its internal communication parameters to function accordingly. Only one APR3-PRT1 can be
connected to each Spectra control panel.
Modules with the APR- prefix are compatible with Spectra (versions 2.0 and higher) and Digiplex. Modules with the
APR3- prefix are compatible with Spectra (versions 2.0 and higher), Digiplex and DigiplexNE.
Bold = Default Setting
SECTION [550]: GENERAL OPTIONS
Option
[1]
[2]
[3]
[4]
[5]
[6]
[7]
[8]
Assigned to Partition 1
Assigned to Partition 2
PGM normal state
Print Arming and disarming events
Print Alarm and Alarm Restore events
Print Tamper and Tamper Restore events
Print Trouble and Trouble Restore events
Print Special events
OFF
N Disabled
N Disabled
N Normally Open (N.O.)
N Disabled
N Disabled
N Disabled
N Disabled
N Disabled
ON
N Enabled
N Enabled
N Normally Closed (N.C.)
N Automatically
N Automatically
N Automatically
N Automatically
N Automatically
SECTION [551]: AUTOMATIC ZONE STATUS PRINTING
Option
[1]
[2]
[3]
[4]
[5]
[6]
[7]
[8]
OFF
N Disabled
N Disabled
N Disabled
N Disabled
N Disabled
N Disabled
N Disabled
N Disabled
Print status of Zone 1
Print status of Zone 2
Print status of Zone 3
Print status of Zone 4
Print status of Zone 5
Print status of Zone 6
Print status of Zone 7
Print status of Zone 8
ON
N Automatically
N Automatically
N Automatically
N Automatically
N Automatically
N Automatically
N Automatically
N Automatically
SECTION [552]: AUTOMATIC ZONE STATUS PRINTING
Option
[1]
[2]
[3]
[4]
[5]
[6]
[7]
[8]
OFF
N Disabled
N Disabled
N Disabled
N Disabled
N Disabled
N Disabled
N Disabled
N N/A
Print status of Zone 9
Print status of Zone 10
Print status of Zone 11
Print status of Zone 12
Print status of Zone 13
Print status of Zone 14
Print status of Zone 15
N/A
Spectra 1759EX
- 21 -
Programming Guide
ON
N Automatically
N Automatically
N Automatically
N Automatically
N Automatically
N Automatically
N Automatically
N N/A
Bold = Default Setting
SECTION [553]: SERIAL AND PARALLEL PORT SETUP OPTIONS
Option
[1]
[2]&[3]
[4]
[5]
[6]
[7]
[8]
Serial port
Baud Rate Settin gs
[2]
[3]
OF F
O FF
1200 baud (default)
APR-PRT1
2400 bau d (default)
APR3-PRT1
9600 baud
ON
O FF
2400 baud
OF F
ON
9600 baud
19200 baud
ON
ON
19200 baud
57600 baud
Parallel port
Off-line status ignored (parallel port only)
Paper empty status ignored (parallel port only)
Printer fault status ignored (parallel port only)
Printer busy status ignored (parallel port only)
OFF
N Disabled
N see table
N see table
ON
N Enabled
N see table
N see table
N Disabled
N Disabled
N Disabled
N Disabled
N Disabled
N
N
N
N
N
Enabled
Enabled
Enabled
Enabled
Enabled
PGM PROGRAMMING
The PGM Deactivation event can be used as another activation event if the PGM Timer (section [554]) is programmed with a
value other than 000. The APR3-PRT1 module uses the same PGM events as the Spectra control panel, please refer to
“Programmable Outputs” on page 9
Section #
Decimal Value (000-255)
[554] ___/___/___ seconds (000 = follow deactivation event)
Section #
[555] PGM1 Activation Event
[556] PGM1 Deactivation Event
Description
PG M1 T I ME R
Event Group # Sub-Group #
___/___
___/___
___/___
___/___
CLOCK PROGRAMMING
Default Value
5 sec.
Partition #
___/___
___/___
For example, to enter the date March 26, 2000 you would enter 20 (century), 00 (year), 03 (month), and 26 (day).
Section #
[557]
Value
Year ___/___/___/___ Month ___/___ Day ___/___
Spectra 1759EX
- 22 -
Programming Guide
VOICE-ASSISTED ARM/DISARM BUS MODULE V2.0
Due to InTouch’s Auto-recognition feature, it can be used with either the Spectra (V2.0 or higher), Digiplex or DigiplexNE
control panel. When connected to the bus, InTouch automatically detects which control panel it is connected to and adjusts
its internal communication parameters to function accordingly. Only one InTouch can be connected to each Spectra control
panel.
APR3-ADM2 can also be programmed using the WinLoad Software. Refer to the WinLoad Online Help for more information.
Modules with the APR- prefix are compatible with Spectra (versions 2.0 and higher) and Digiplex. Modules with the
APR3- prefix are compatible with Spectra (versions 2.0 and higher), Digiplex and DigiplexNE.
Section #
[575] ___/___/___
[576] ___/___/___
[577] ___/___/___
Decimal Value (000-255)
rings (000 = disabled)
seconds (010-255, 000 = disabled)
seconds/minutes (000 = disabled)
Description
N U MB ER O F R IN GS
AN SW ER IN G M AC H IN E OVE RR ID E
PG M T IM ER
Default Value
8 rings
000
005
Bold = Default Setting
SECTION [578]: GENERAL OPTIONS
Option
[1]
[2]
[3]
[4]
[5]
[6]
[7]
[8]
OFF
N 6-digits
N Disabled
N Disabled
N Seconds
N N/A
N N/A
N N/A
N N/A
Stand-alone Code length
Partitioned system
PGM output
PGM time in
Future use
Future use
Future use
Future use
Spectra 1759EX
- 23 -
Programming Guide
ON
N 4-digits
N Enabled
N Enabled
N Minutes
N N/A
N N/A
N N/A
N N/A
WIRELESS EXPANSION ZONE PROGRAMMING
ZONE ASSIGNMENT
The serial number can be located on the inside of the transmitter or you can use the Serial Number Display feature (see
page 24). Also, refer to “Zone Recognition Table” on page 6.
Section #
Serial #
[601] ___/___/___/___/___/___=
EXPA N SION IN PU T
1
[602] ___/___/___/___/___/___=
EXPA N SION IN PU T
2
[603] ___/___/___/___/___/___=
EXPA N SION IN PU T
3
[604] ___/___/___/___/___/___=
EXPA N SION IN PU T
4
[605] ___/___/___/___/___/___=
EXPA N SION IN PU T
5
[606] ___/___/___/___/___/___=
EXPA N SION IN PU T
6
[607] ___/___/___/___/___/___=
EXPA N SION IN PU T
7
[608] ___/___/___/___/___/___=
EXPA N SION IN PU T
8
Bold = Default Setting
SECTION [610]: GENERAL OPTIONS
Option
[1]
[2]
[3] & [4]
[5]
[6]
[7]
[8]
Wireless transmitter check-in supervision
Check-in supervision base time setting (must
be same as the transmitter’s jumper setting)
Future use
Check-in supervision time value (must be same
as the transmitter’s jumper setting)
Future use
Future use
Remote control assignment mode
OFF
N Disabled
N Hours
ON
N Enabled
N Minutes
N N/A
N 12
N N/A
N6
N N/A
N N/A
N Omnia (OMN-RCT1)
N N/A
N N/A
N ParaKey (LIB-344)
SERIAL NUMBER DISPLAY
Section #
[630]
Description
Press the tamper switch of the Omnia Wireless Transmitter. The keypad will emit a confirmation beep. On
LED keypads, press the [EN T ER ] key to view the digits one at a time. On LCD keypads, the first 3 digits of
the serial number will appear. Press the [EN T ER ] key 3 times to view the next 3 digits. Continue activating
the desired transmitters or press [C LE AR ] to exit.
SIGNAL STRENGTH DISPLAY
Section #
Description
After entering the desired section, activate the Omnia Wireless Transmitter by opening/closing the zone
or by pressing the tamper switch. Always ignore the first reading as it won’t be accurate. An average
reading of 3 and up is acceptable.
[631]
[632]
[633]
[634]
[635]
[636]
[637]
[638]
Display Signal Strength of Expansion
Display Signal Strength of Expansion
Display Signal Strength of Expansion
Display Signal Strength of Expansion
Display Signal Strength of Expansion
Display Signal Strength of Expansion
Display Signal Strength of Expansion
Display Signal Strength of Expansion
Spectra 1759EX
Input
Input
Input
Input
Input
Input
Input
Input
1 - Section [601]
2 - Section [602]
3 - Section [603]
4 - Section [604]
5 - Section [605]
6 - Section [606]
7 - Section [607]
8 - Section [608]
- 24 -
Programming Guide
REMOTE CONTROL USER ASSIGNMENT
Section #
[701]
[702]
[703]
[704]
[705]
[706]
[707]
[708]
Decimal Value
___/___/___(001-048 =
___/___/___(001-048 =
___/___/___(001-048 =
___/___/___(001-048 =
___/___/___(001-048 =
___/___/___(001-048 =
___/___/___(001-048 =
___/___/___(001-048 =
user #)
user #)
user #)
user #)
user #)
user #)
user #)
user #)
Description
remote control #1 - section [731]*
remote control #2 - section [732]*
remote control #3 - section [733]*
remote control #4 - section [734]*
remote control #5 - section [735]*
remote control #6 - section [736]*
remote control #7 - section [737]*
remote control #8 - section [738]*
Default Value
000
000
000
000
000
000
000
000
* refer to “Remote Control Assignment” on page 26.
BUTTON OPTIONS
Section #
[711]
Hexa Value: Each digit is a value from 1 to D (see Button Options Table)
____/____/____/____/____/____/____/____ remote control #1
A
B
C
D A+B C+D A+C B+D
[712]
____/____/____/____/____/____/____/____ remote control #2
A
B
C
D A+B C+D A+C B+D
[713]
____/____/____/____/____/____/____/____ remote control #3
A
B
C
D A+B C+D A+C B+D
[714]
____/____/____/____/____/____/____/____ remote control #4
A
B
C
D A+B C+D A+C B+D
[715]
____/____/____/____/____/____/____/____ remote control #5
A
B
C
D A+B C+D A+C B+D
[716]
____/____/____/____/____/____/____/____ remote control #6
A
B
C
D A+B C+D A+C B+D
[717]
____/____/____/____/____/____/____/____ remote control #7
A
B
C
D A+B C+D A+C B+D
[718]
____/____/____/____/____/____/____/____ remote control #8
A
B
C
D A+B C+D A+C B+D
Spectra 1759EX
- 25 -
Please note that the User Code
assigned to the remote control
(sections [701] to [708]) must
have the same User Options and
Button Options enabled. For example,
if you enable the Force Arming button
option
you
must
enable
the
appropriate Force Arming user option.
Also, if you enable any of the Panic
button options, you must enable the
Panic options in the control panel.
Programming Guide
REMOTE CONTROL ASSIGNMENT
Enter the appropriate section and press any button on the remote control twice to assign the remote control. If you hear a
rejection beep, an error has occurred or the remote control has already been assigned. To delete a remote control, enter the
desired section and then press the [F OR C E ] button.
Section #
[731]
[732]
[733]
[734]
[735]
[736]
[737]
[738]
Spectra 1759EX
R EM OT E
#1
#2
C ON T RO L #3
C ON T RO L #4
C ON T RO L #5
C ON T RO L #6
C ON T RO L #7
C ON T RO L #8
- 26 -
Programming Guide
R EM OT E C ON T RO L
R EM OT E C ON T RO L
R EM OT E
R EM OT E
R EM OT E
R EM OT E
R EM OT E
ZONE EXPANSION BUS MODULES
Only one SPC/APR3-ZX4 or one SPC/APR3-ZX8 can be connected to each Spectra control panel. The following sections
are for SPC-ZX4 version 1.0, APR3-ZX4 version 1.0, SPC-ZX8 version 1.0 and APR3-ZX8 version 2.0.
Modules with the APR- prefix are compatible with Spectra (versions 2.0 and higher) and Digiplex. Modules with the
APR3- prefix are compatible with Spectra (versions 2.0 and higher), Digiplex and DigiplexNE.
Bold = Default Setting
SECTION [650]: Options
Option
[1]
[2]
[3]
[4]-[8]
EOL (end-of-line) resistors for hardwire modules
Zone Expansion Module tamper recognition
PGM1 on SPC/APR3-ZX8 follows Global PGM
programmed in sections [124] & [125]
Future Use
OFF
N No EOL
N Disabled
N Disabled
ON
N Use EOL Resistors
N Z1 becomes tamper input
N Enabled
N N/A
N N/A
OFF
N Disabled
N Disabled
N Disabled
N Disabled
N Disabled
N Disabled
N Disabled
N Disabled
ON
N Enabled
N Enabled
N Enabled
N Enabled
N Enabled
N Enabled
N Enabled
N Enabled
SECTION [651]: ZONE ASSIGNMENT
Option
[1]
[2]
[3]
[4]
[5]
[6]
[7]
[8]
See “Zone Recognition Table” on page 6.
Input Z1
=Expansion Input 1
Input Z2
=Expansion Input 2
Input Z3
=Expansion Input 3
Input Z4
=Expansion Input 4
Input Z5 (S PC /APR 3- Z X8 only) =Expansion Input 5
Input Z6 (S PC /APR 3- Z X8 only) =Expansion Input 6
Input Z7 (S PC /APR 3- Z X8 only) =Expansion Input 7
Input Z8 (S PC /APR 3- Z X8 only) =Expansion Input 8
PGM PROGRAMMING (SPC-ZX8 and APR3-ZX8 Only)
The PGM will only activate or deactivate 100mS after the selected event occurs. The PGM Deactivation event can be used
as another activation event if the PGM Timer (section [655]) is programmed with a value other than 000. The system will
ignore the PGM if it has been programmed to follow the Global PGM (option [3] in section [650]). Only PGM events from the
table below can be used.
Section #
Decimal Value (000-255)
[655] ___/___/___ seconds (000 = follow deactivation event)
Section #
[656] PGM1 Activation Event
[657] PGM1 Deactivation Event
PG M1 T I ME R
Event Group # Sub-Group #
___/___
___/___
___/___
___/___
Event Group #
For SPC-ZX8:
60 = Hardwire
61 = Hardwire
62 = Hardwire
63 = Hardwire
Description
Zone Opened
Zone Closed
Tamper Opened
Tamper Closed
For APR3-ZX8:
60 = Hardwire Zone/Hardwire Tamper Opened
61 = Hardwire Zone/Hardwire Tamper Closed
01
02
03
04
05
06
07
08
99
Spectra 1759EX
Default Value
5 sec.
Partition #
___/___
___/___
Sub-Group #
Partition #
= Expansion Input 1 - Section [651] - [1]
= Expansion Input 2 - Section [651] - [2]
= Expansion Input 3 - Section [651] - [3]
= Expansion Input 4 - Section [651] - [4]
= Expansion Input 5 - Section [651] - [5]
= Expansion Input 6 - Section [651] - [6]
= Expansion Input 7 - Section [651] - [7]
= Expansion Input 8 - Section [651] - [8]
= Any zone expansion bus module input
Not used; enter 00
- 27 -
Programming Guide
USER OPERATION
PARTITIONING
The Spectra system is equipped with a partitioning feature which can divide the alarm system into two distinct areas
identified as Partition 1 and Partition 2. Partitioning can be used in installations where shared security systems are more
practical, such as an office/warehouse building. If the system is not partitioned, all User Codes and features will be
recognized as belonging to Partition 1.
How does a partitioned system work?
• Users can only arm or disarm their assigned partitions.
• Only zones assigned to Partition 1 will arm or disarm when Partition 1 is armed or disarmed.
• Only zones assigned to Partition 2 will arm or disarm when Partition 2 is armed or disarmed.
• Zones assigned to both partitions will arm when both partitions are armed and will disarm when
at least one disarms.
• Some of the system’s features can be programmed separately for each partition.
PROGRAMMING ACCESS CODES
User Access Codes are personal identification numbers that allow users to enter certain programming modes, arm or disarm
the alarm system as well as activate or deactivate PGMs. Spectra security systems support the following:
System Master Code can arm or disarm any partition using any arming method and can create, modify or delete any User
Access Code. Only the System Master Code can modify or delete User Access Codes assigned to both partitions.
Master Code 1 is permanently assigned to partition 1 and can be used to create, modify or delete User Access Codes that
are assigned to partition 1.
Master Code 2 is permanently assigned to partition 2 (except when partitioning is disabled, Master Code 2 will be assigned
to partition 1) and can be used to create, modify or delete User Access Codes that are assigned to the same partition.
45 User Access Codes (including 1 Duress code)
How Do I Program Access Codes?
1) Press [E NT E R]
2) Key in the [S YST EM M AS T ER C OD E ] or [ MA ST E R C OD E ]
3) Key in 3-digit [ SEC T ION ] (see User Code Table)
4) Key in new 4- or 6-digit [A C CE SS C OD E ]
[E N TE R ] flashes. Return to step 3
How Do I Delete Access Codes?
1) Repeat steps 1 to 3 (see above)
2) Press the [F OR C E ] key once for each digit in the access code (4 or 6 times) until the
keypad emits a Confirmation Beep.
User Code Table
Section
[001]
[002]
[003]
[004] T O [047]
[048]
User Codes
User Code 001 = System Master Code
User Code 002 = Master Code 1
User Code 003 = Master Code 2
User Code 004 to User Code 047
User Code 048 or Duress Code
Spectra 1759EX
- 28 -
Programming Guide
PROGRAMMING CHIME ZONES
This feature allows users to program which zones will be Chime Enabled. A Chime Enabled zone will cause the keypad to
emit a rapid intermittent beep tone (BE EP - BEE P -B EEP -BE EP ) advising the user every time it is opened. Each keypad must be
Chime Programmed separately. Keypad chimes must be re-programmed if the system suffers a total power loss (16-zone LED
and LCD Keypads only).
10-Z ON E LED K EYPA D :
Press and hold any key from [1] to [10] for 3 seconds to activate or deactivate Chiming for zones 1 to 10. For example, press
and hold the [1] key to enable chiming on zone 1. If, after pressing and holding a key, the keypad emits a confirmation beep,
this means the chime feature has been enabled for that zone. If the keypad emits a Rejection Beep, this means the Chime
feature has been disabled for the corresponding zone.
16-Z ON E LED K EYPA D :
Press and hold the [9] key. Enter the 2-digit (01 to 16) zone number(s). When the corresponding LED is on, the zone is
chimed. When the corresponding LED is off, the zone is unchimed. When the desired zones are chimed, press [E NT E R].
LCD K EYPA D :
Press and hold the [9] key. Enter the 2-digit (01 to 16) zone number(s) or use the arrow keys to scroll through the zones.
When the appropriate zone is displayed, press the [F N C 1] key. When the desired zones are chimed, press [EN T ER ].
KEYPAD MUTING
Press and hold the [C L EA R ] key for 3 seconds to enable or disable keypad muting. When muted, the keypad will only beep
when a key is pressed or when the keypad emits a Rejection or Confirmation Beep. All other beep functions are disabled.
KEYPAD BACKLIGHT (1686H and 1686V Only)
The illumination level behind the keys can be modified to suit the user’s needs. There are four backlight levels. The [M EM ] key
is used to set the desired level. Each consecutive push of the [ ME M] key will increase the backlight level until the maximum
level is reached. After reaching the maximum level, the backlight level will return to the lowest level and the whole process is
repeated. To change the backlight level:
How do I Modify The Backlight?
1) Press and hold the [M EM ] key for 3 seconds
2) The [M EM ] key will illuminate
3) Press the [M EM ] key to set the desired backlight level
4) Press [ CL E AR ] or [E NT E R] to exit
QUICK FUNCTION KEYS
IN STA L L ER TE ST M OD E
[E NT E R] + [I NS TA L L ER C OD E ] + [ T B L ] or [T RB L ]
The Installer Test Mode allows you to perform walk tests where the bell/siren will squawk once to indicate an open zone and
twice to indicate a closed zone. To enter this mode, press [ EN T ER ] + [ IN ST AL L E R C OD E ] + [T B L ] or [ T RB L ]. The keypad will emit
a Confirmation Beep. To disable this mode, press the [ TB L ] or [T R B L] key again. The keypad will emit a Rejection Beep.
TE ST R EP OR T
[E NT E R] + [I NS TA L L ER /MA S TE R C OD E ] + [ ME M]
Sends the “Test Report” report code programmed in section [211] to the central station.
CA L L W IN LOA D S OF T W A RE
[E NT E R] + [I NS TA L L ER /MA S TE R C OD E ] + [ BY P ]
This feature is used to establish communication between the control panel and a computer using the WinLoad Software.
After entering this mode, the control panel will dial the telephone number programmed in section [150].
CA N C EL C OM MU N IC A TI ON
[E NT E R] + [I NS TA L L ER /MA S TE R C OD E ] + [ STA Y ]
Cancels all communication until the next reportable event. If the Master Code was used, only communication with WinLoad
would be cancelled.
AN SW ER WIN LOA D S O F TW A RE
[E NT E R] + [I NS TA L L ER /MA S TE R C OD E ] + [ FO RC E ]
Forces the control panel to pick-up an incoming telephone call.
Spectra 1759EX
- 29 -
Programming Guide
APPENDIX A - ADEMCO CID REPORT CODE LIST (PROG.)
If using the Ademco Contact ID Programmable code format, enter the 2-digit hexadecimal value from the table below (Prog.
Value) into sections [160] to [213] to program the desired report codes. To enter a 0 value press the [F OR C E ] key.
CID#
Reporting
Code
Prog.
Value
MEDICAL ALARMS - 100
100
Medical Alarm
01
101
Pendant Transmitter
02
102
Fail to Report In
03
FIRE ALARMS - 110
110
Fire Alarm
04
111
Smoke
05
112
Combustion
06
113
Water Flow
07
114
Heat
08
115
Pull Station
09
116
Duct
0A
117
Flame
0B
118
Near Alarm
0C
PANIC ALARMS - 120
120
Panic Alarm
0D
121
Duress
0E
122
Silent
0F
123
Audible
10
BURGLAR ALARMS - 130
130
Burglary
11
131
Perimeter
12
132
Interior
13
133
24-Hour
14
134
Entry/Exit
15
135
Day/Night
16
136
Outdoor
17
137
Tamper
18
138
Near Alarm
19
GENERAL ALARMS - 140
140
General Alarm
1A
141
Polling Loop Open
1B
142
Polling Loop Short
1C
143
Expansion Module Failure
1D
144
Sensor Tamper
1E
145
Expansion Module Tamper
1F
24-HOUR NON-BURGLARY - 150 & 160
150
24-Hour Non-Burglary
20
151
Gas Detected
21
152
Refrigeration
22
153
Loss of Heat
23
154
Water Leakage
24
155
Foil Break
25
156
Day Trouble
26
157
Low Bottled Gas Level
27
158
High Temp
28
159
Low Temp
29
161
Loss of Air Flow
2A
FIRE SUPERVISORY - 200 & 210
200
Fire Supervisory
2B
201
Low Water Pressure
2C
202
Low CO2
2D
CID#
Reporting
Code
Prog.
Value
203
Gate Valve Sensor
2E
204
Low Water Level
2F
205
Pump Activated
30
206
Pump Failure
31
SYSTEM TROUBLES - 300 & 310
300
System Trouble
32
301
AC Loss
33
302
Low System Battery
34
303
RAM Checksum Bad
35
304
ROM Checksum Bad
36
305
System Reset
37
306
Panel Program Changed
38
307
Self-Test Failure
39
308
System Shutdown
3A
309
Battery Test Failure
3B
310
Ground Fault
3C
SOUNDER/RELAY TROUBLES - 320
320
Sounder Relay
3D
321
Bell 1
3E
322
Bell 2
3F
323
Alarm Relay
40
324
Trouble Relay
41
325
Reversing
42
SYSTEM PERIPHERAL TROUBLES - 330 & 340
330
System Peripheral
43
331
Polling Loop Open
44
332
Polling Loop Short
45
333
Exp. Module Failure
46
334
Repeater Failure
47
335
Local Printer Paper Out
48
336
Local Printer Failure
49
COMMUNICATION TROUBLES - 350 & 360
350
Communication
4A
351
Telco Fault 1
4B
352
Telco Fault 2
4C
353
Long Range Radio
4D
354
Fail to Communicate
4E
355
Loss of Radio Supervision
4F
356
Loss of Central Polling
50
PROTECTION LOOP TROUBLES - 370
370
Protection Loop
51
371
Protection Loop Open
52
372
Protection Loop short
53
373
Fire Trouble
54
SENSOR TROUBLES - 380
380
Sensor Trouble
55
381
Loss of Super. -RF
56
382
Loss of Super. - RPM
57
383
Sensor Tamper
58
384
RF xmtr. Low Battery
59
OPEN/CLOSE - 400
400
Open/Close
5A
Spectra 1759EX
- 30 -
CID#
Reporting
Code
Prog.
Value
401
O/C by User
5B
402
Group O/C
5C
403
Automatic O/C
5D
404
Late to O/C
5E
405
Deferred
5F
406
Cancel
60
407
Remote Arm/Disarm
61
408
Quick Arm
62
409
Keyswitch O/C
63
REMOTE ACCESS - 410
411
Callback Request Made
64
412
Success - Download Access 65
413
Unsuccessful Access
66
414
System Shutdown
67
415
Dialer Shutdown
68
ACCESS CONTROL - 420
421
Access Denied
69
422
Access Report By User
6A
SOUNDER RELAY DISABLES - 520
520
Sounder/Relay Disabled
6B
521
Bell 1 Disable
6C
522
Bell 2 Disable
6D
523
Alarm Relay Disable
6E
524
Trouble Relay Disable
6F
525
Reversing Relay Disable
70
COMMUNICATION DISABLES - 550 & 560
551
Dialer Disabled
71
552
Radio xmitter Disabled
72
BYPASSES - 570
570
Zone Bypass
73
571
Fire Bypass
74
572
24-Hour Zone Bypass
75
573
Burg. Bypass
76
574
Group Bypass
77
TEST/MISC. - 600
601
Manual Trigger Test
78
602
Periodic Test Report
79
603
Periodic RF Xmission
7A
604
Fire Test
7B
605
Status Report to Follow
7C
606
Listen-in to Follow
7D
607
Walk Test Mode
7E
621
Event Log Reset
7F
622
Event Log 50% Full
80
623
Event Log 90% Full
81
624
Event Log Overflow
82
625
Time/Date Reset
83
626
Time/Date Inaccurate
84
627
Program Mode Entry
85
628
Program Mode Exit
86
631
Exception Schedule Change 87
Programming Guide
APPENDIX B - ADEMCO CID REPORT CODE LIST (ALL CODES)
System Event
Default Contact ID Report Code when
option [3] is on in section [136]
System Event
Default Contact ID Report Code when
option [3] is on in section [136]
Arming with Master Code (##)
3 4A1 - Close by user
Auxiliary supply trouble
1 3AA - System trouble
Arming with User Code (##)
3 4A1 - Close by user
Bell output current limit
1 321 - Bell 1
Arming with Keyswitch (##)
3 4A9 - Keyswitch Close
Bell absent
1 321 - Bell 1
Auto Arming
3 4A3 - Automatic Close
Clock lost
1 626 - Time/Date inaccurate
Arm with PC software
3 4A7 - Remote arm/disarm
Fire loop trouble
1 373 - Fire trouble
Late To Close
3 4A4 - Late to Close
Wireless Transmitter
Low Battery
1 384 - RF xmtr. low battery
No Movement
3 4A4 - Late to Close
Wireless Transmitter
Supervision Loss
1 381 - Loss of super. - RF
Partial arming
1 574 - Group bypass
Module fault
1 333 - Expansion module failure
Quick arming
3 408 - Quick arm
Printer fault
1 336 - Local printer failure
Fail to communicate with
central station
1 354 - Fail to communicate
Disarm with Master Code (##)
1 4A1 - Open by user
Wireless Transmitter
Low Battery
1 384 - RF xmtr. low battery
Disarm with User Code (##)
1 4A1 - Open by user
TLM trouble restore
3 351 - Telco 1 fault restore
Disarm with Keyswitch (##)
1 4A9 - Keyswitch Open
AC Failure restore
3 3A1 - AC loss restore
Disarm after alarm with
Master Code (##)
1 4A1 - Open by user
Battery Failure restore
3 3A9 - Battery test restore
Disarm after alarm with
User Code (##)
1 4A1 - Open by user
Auxiliary supply trouble restore
3 3AA - System trouble restore
Disarm after alarm with
Keyswitch (##)
1 4A9 - Keyswitch Open
Bell output current limit restore
3 321 - Bell 1 restore
Bell absent restore
3 321 - Bell 1 restore
Auto Arming Cancellation
1 4A5 - Deferred Open/Close
Clock programmed
3 626 - Time/Date Reset
Disarm with PC software
1 4A7 - Remote arm/disarm
Fire loop trouble restore
3 373 - Fire trouble restore
Disarm after an alarm with
PC software
1 4A7 - Remote arm/disarm
Wireless Transmitter
Low Battery
3 384 - RF xmtr. low battery
Wireless Transmitter
Supervision Loss
3 381 - Loss of super. - RF
Zone Bypassed (##)
1 57A - Zone bypass
Module fault restore
3 333 - Expansion module failure
restore
Zone alarm (##)
1 13A - Burglary Alarm
Printer fault restore
3 336 - Local printer failure restore
Fire alarm (##)
1 11A - Fire alarm
Fail to communicate with
central station
3 354 - Fail to communicate restore
Zone alarm restore (##)
3 13A - Burglary Alarm Restore
Fire alarm restore (##)
3 11A - Fire alarm Restore
Cold Start
1 3A8 - System shutdown
Test Report engaged
1 6A2 - Periodic test report
Panic 1 - Emergency
1 12A - Panic alarm
PC software communication
finished
1 412 - Successful - download access
Panic 2 - Medical
1 1AA - Medical alarm
Installer on site
1 627 - Program mode Entry
Panic 3 - Fire
1 115 - Pull Station
Installer programming finished
1 628 - Program mode Exit
Recent closing
3 4AA - Open/Close
Global zone shutdown
1 574 - Group bypass
Duress alarm
1 121 - Duress
Zone shutdown (##)
1 57A - Zone bypass
Zone tampered (##)
1 144 - Sensor tamper
Zone tamper restore (##)
3 144 - Sensor tamper restore
AC Failure
1 3A1 - AC loss
Battery Failure
1 3A9 - Battery test failure
Spectra 1759EX
- 31 -
Programming Guide
BUS MODULE CONNECTIONS
PRINTER MODULE (APR3-PRT1)
Spectra 1759EX
- 32 -
Programming Guide
4-PGM OUTPUT MODULE (APR3-PGM4)
4-ZONE EXPANSION BUS MODULE (SPC-ZX4 AND APR3-ZX4)
Spectra 1759EX
- 33 -
Programming Guide
VOICE-ASSISTED ARM/DISARM BUS MODULE (APR3-ADM2)
Spectra 1759EX
- 34 -
Programming Guide
8-ZONE EXPANSION BUS MODULES (SPC-ZX8 AND APR3-ZX8)
Spectra 1759EX
- 35 -
Programming Guide
HARDWARE CONNECTIONS
SINGLE ZONE INPUTS
CONNECTING FIRE CIRCUITS, KEYSWITCHES AND PGMS
It is recommended that all 4-wire smoke detectors be connected using a daisy chain configuration.
Spectra 1759EX
- 36 -
Programming Guide
ALARM RELAY AND PGM CONNECTIONS
CONNECTING MORE THAN TWO KEYPADS
If there are more than two keypads connected to the control panel and at least one keypad zone is being used, connect as
shown and program as described in the Spectra Control Panels Reference & Installation manual.
AC POWER & BACKUP BATTER Y CONNECTIONS
Spectra 1759EX
- 37 -
Programming Guide
SPECTRA 1759EX PCB LAYOUT
Refer to “AC Power
& Backup Battery
Connections” on
page 37.
Refer to: Single Zone Inputs
on page 36
To connect the 5A Alarm Relay and the PGMs,
refer to “Alarm Relay and PGM Connections ” on
page 37. To connect AC power, refer to “AC Power
& Backup Battery Connections” on page 37.
For the keypad’s zone, EOL and tamper
configurations, refer to page 5.
Spectra 1759EX
- 38 -
Programming Guide
P RINT ED I N CA NAD A
11/2002
1759EX-EP01
Download PDF
Similar pages