ESPAÑOL
FRANÇAIS
Super Audio CD
/ Blu-Ray Disc player
UD9004
ENGLISH
ENGLISH
FRANÇAIS
ESPAÑOL
nSAFETY PRECAUTIONS
CAUTION
RISK OF ELECTRIC SHOCK
DO NOT OPEN
CAUTION:
TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT REMOVE
COVER (OR BACK). NO USER-SERVICEABLE PARTS INSIDE.
REFER SERVICING TO QUALIFIED SERVICE PERSONNEL.
The lightning flash with arrowhead symbol, within an equilateral
triangle, is intended to alert the user to the presence of
uninsulated “dangerous voltage” within the product’s enclosure
that may be of sufficient magnitude to constitute a risk of electric
shock to persons.
The exclamation point within an equilateral triangle is intended
to alert the user to the presence of important operating
and maintenance (servicing) instructions in the literature
accompanying the appliance.
WARNING:
TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK, DO NOT
EXPOSE THIS APPLIANCE TO RAIN OR MOISTURE.
CAUTION:
1.
2.
3.
4.
5.
6.
7.
8.
9.
10.
11.
12.
13.
USE OF CONTROLS OR ADJUSTMENTS OR PERFORMANCE
OF PROCEDURES OTHER THAN THOSE SPECIFIED HEREIN MAY
RESULT IN HAZARDOUS RADIATION EXPOSURE.
THIS PRODUCT SHOULD NOT BE ADJUSTED OR REPAIRED BY
ANYONE EXCEPT PROPERLY QUALIFIED SERVICE PERSONNEL.
nLaser Class (IEC 60825-1:2001)
CLASS 1
,,
LASER PRODUCT
IMPORTANT SAFETY
INSTRUCTIONS
Read these instructions.
Keep these instructions.
Heed all warnings.
Follow all instructions.
Do not use this apparatus near water.
Clean only with dry cloth.
Do not block any ventilation openings.
Install in accordance with the manufacturer's instructions.
Do not install near any heat sources such as radiators, heat registers, stoves,
or other apparatus (including amplifiers) that produce heat.
Do not defeat the safety purpose of the polarized or grounding-type plug. A
polarized plug has two blades with one wider than the other. A grounding
type plug has two blades and a third grounding prong. The wide blade or the
third prong are provided for your safety. If the provided plug does not fit into
your outlet, consult an electrician for replacement of the obsolete outlet.
Protect the power cord from being walked on or pinched particularly at
plugs, convenience receptacles, and the point where they exit from the
apparatus.
Only use attachments/accessories specified by the manufacturer.
Use only with the cart, stand, tripod, bracket, or table
specified by the manufacturer, or sold with the apparatus.
When a cart is used, use caution when moving the cart/
apparatus combination to avoid injury from tip-over.
Unplug this apparatus during lightning storms or when
unused for long periods of time.
14. Refer all servicing to qualified service personnel.
Servicing is required when the apparatus has been damaged in any way,
such as power-supply cord or plug is damaged, liquid has been spilled or
objects have fallen into the apparatus, the apparatus has been exposed to
rain or moisture, does not operate normally, or has been dropped.
15. Batteries shall not be exposed to excessive heat such as sunshine, fire or
the like.
CAUTION:
•The ventilation should not be impeded by covering the ventilation
openings with items, such as newspapers, tablecloths, curtains,
etc.
•No naked flame sources, such as lighted candles, should be
placed on the unit.
•Observe and follow local regulations regarding battery disposal.
•Do not expose the unit to dripping or splashing fluids.
•Do not place objects filled with liquids, such as vases, on the
unit.
ATTENTION:
•La ventilation ne doit pas être gênée en recouvrant les ouvertures
de la ventilation avec des objets tels que journaux, rideaux, tissus,
etc.
•Aucune flamme nue, par exemple une bougie, ne doit être placée
sur l’appareil.
•Veillez à respecter les lois en vigueur lorsque vous jetez les piles
usagées.
•L’appareil ne doit pas être exposé à l’eau ou à l’humidité.
•Ne pas poser d’objet contenant du liquide, par exemple un vase,
sur l’appareil.
PRECAUCIÓN:
•La ventilación no debe quedar obstruida por haberse cubierto las
aperturas con objetos como periódicos, manteles, cortinas, etc.
•No debe colocarse sobre el aparato ninguna fuente inflamable sin
protección, como velas encendidas.
•A la hora de deshacerse de las pilas, respete la normativa para el
cuidado del medio ambiente.
•No exponer el aparato al goteo o salpicaduras cuando se utilice.
•No colocar sobre el aparato objetos llenos de líquido, como
jarros.
CAUTION:
To completely disconnect this product from the mains, disconnect
the plug from the wall socket outlet.
The mains plug is used to completely interrupt the power supply to
the unit and must be within easy access by the user.
PRECAUTION:
,,
Pour déconnecter complètement ce produit du courant secteur,
débranchez la prise de la prise murale.
La prise secteur est utilisée pour couper complètement
l’alimentation de l’appareil et l’utilisateur doit pouvoir y accéder
facilement.
PRECAUCIÓN:
Para desconectar completamente este producto de la alimentación
eléctrica, desconecte el enchufe del enchufe de la pared.
El enchufe de la alimentación eléctrica se utiliza para interrumpir por
completo el suministro de alimentación eléctrica a la unidad y debe
de encontrarse en un lugar al que el usuario tenga fácil acceso.
I
ESPAÑOL
FCC INFORMATION (For US customers)
FRANÇAIS
ENGLISH
nNOTE ON USE / OBSERVATIONS RELATIVES A L’UTILISATION
1. COMPLIANCE INFORMATION
Product Name: Super Audio CD / Blu-Ray Disk Player
Model Number: UD9004
This product complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this
product may not cause harmful interference, and (2) this product must accept any interference received, including
interference that may cause undesired operation.
2. IMPORTANT NOTICE: DO NOT MODIFY THIS PRODUCT
This product, when installed as indicated in the instructions contained in this manual, meets FCC requirements.
Modification not expressly approved by MARANTZ may void your authority, granted by the FCC, to use the
product.
3. NOTE
This product has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15
of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a
residential installation.
This product generates, uses and can radiate radio frequency energy and, if not installed and used in accordance
with the instructions, may cause harmful interference to radio communications. However, there is no guarantee
that interference will not occur in a particular installation. If this product does cause harmful interference to radio or
television reception, which can be determined by turning the product OFF and ON, the user is encouraged to try to
correct the interference by one or more of the following measures:
•Reorient or relocate the receiving antenna.
•Increase the separation between the equipment and receiver.
•Connect the product into an outlet on a circuit different from that to which the receiver is connected.
•Consult the local retailer authorized to distribute this type of product or an experienced radio/TV technician for
help.
• Keep the unit free from moisture, water,
and dust.
• Protéger l’appareil contre l’humidité, l’eau
et la poussière.
• Do not let foreign objects into the unit.
• Ne pas laisser des objets étrangers dans
l’appareil.
• Avoid high temperatures.
Allow for sufficient heat dispersion when
installed in a rack.
• Eviter des températures élevées.
Tenir compte d’une dispersion de chaleur
suffisante lors de l’installation sur une
étagère.
This Class B digital apparatus complies with Canadian ICES-003.
Cet appareil numérique de la classe B est conforme à la norme NMB-003 du Canada.
• Do not let insecticides, benzene, and
thinner come in contact with the unit.
• Unplug the power cord when not using the • Ne pas mettre en contact des insecticides,
du benzène et un diluant avec l’appareil.
unit for long periods of time.
• Débrancher le cordon d’alimentation
lorsque l’appareil n’est pas utilisé pendant
de longues périodes.
nCopyrights / Droits d’auteur
•It is prohibited by law to reproduce, broadcast, rent or play discs in public without the consent of the
copyright holder.
•La reproduction, la diffusion, la location, le prêt ou la lecture publique de ces disques sont interdits sans
le consentement du détenteur des droits d’auteur.
• Handle the power cord carefully.
Hold the plug when unplugging the cord.
• Manipuler le cordon d’alimentation avec
précaution.
Tenir la prise lors du débranchement du
cordon.
* (For apparatuses with ventilation holes)
• Do not obstruct the ventilation holes.
• Ne pas obstruer les trous d’aération.
• Never disassemble or modify the unit in
any way.
• Ne jamais démonter ou modifier l’appareil
d’une manière ou d’une autre.
II
ENGLISH
Contents
Features··························································································· 2
Getting Started
Accessories····················································································· 2
Cautions on Handling····································································· 3
Cautions on Installation································································· 3
Opening and closing the front panel door···································· 3
About Media··················································································· 3
Playable Media·············································································· 3
Cautions on Using Media······························································ 6
About the Remote Control Unit···················································· 7
Inserting the Batteries··································································· 7
Operating Range of the Remote Control Unit······························ 7
Remote Control Settings (Remote Control Side) ························· 7
Part Names and Functions····························································· 8
Front Panel····················································································· 8
Display··························································································· 8
Rear Panel······················································································ 9
Remote Control Unit··································································· 10
GUI Menu Setup
Menu Map····················································································· 23
GUI Menu Operation···································································· 24
Examples of GUI Menu Screen Displays···································· 24
Language Setup············································································ 25
HDMI Setup··················································································· 25
Video Setup·················································································· 26
Audio Setup·················································································· 27
Pure Direct Setup········································································· 30
Ratings·························································································· 31
Network Setup············································································· 31
Display Setup················································································ 32
Other Setup·················································································· 32
Various Settings
Setting the Audio Mode······························································· 33
Changing the Playback File Display············································ 34
Making Other Settings································································· 34
Adjusting the Picture Quality (Picture Control)························· 35
HDMI Control Function················································ 49
Other Information
Connections
Preparation··················································································· 12
Cables Used for Connections····················································· 12
1. Home Theater Playback
– Playing Back Using Multi-channel System –··························· 13
Using an HDMI Cable to Connect to an AV Amp or Television···· 13
Required Settings for HDMI Connection···································· 15
Connection to an AV Amp with No HDMI Audio Input··············· 17
Connecting to a Device with an Analog Multi-channel
Audio Input Terminal··································································· 18
Connection to an AV Amp with No HDMI Video Input··············· 18
2. Playing Back with a Direct Connection to a TV····················· 19
3. Playing Back 2-Channel Audio················································ 20
Connecting to a Device with Analog 2-channel Audio Input
Terminal with Balanced Cable····················································· 20
Connecting to a Device with Analog 2-channel Audio Input
Terminal with Stereo Pin Plug Cable··········································· 20
4. Recording a CD········································································· 20
Connecting to a Digital Recording Device·································· 20
5. Updating to the UD9004’s Latest Software Version············· 21
Connecting to the Network························································· 21
Connecting the Power Cord························································ 22
Once Connections are Completed·············································· 22
Turning the Power On·································································· 22
Operations Enabled During Playback········································· 43
Pause Playback············································································ 43
Stop Playback (Resume Function)·············································· 43
Skipping to the Chapter/Track/File You Want to Playback·········· 43
Looking for Specific Sections Using the Search Modes············ 44
Memorizing Locations You Want to Replay (Marker Function) · ·· 45
Fast Forward/Fast Reverse·························································· 45
Step-by-Step Playback································································ 45
Slow Forward/Slow Reverse Playback········································ 45
Playback in Any Order (Random Playback)································· 46
Playing Back Repeatedly (Repeat Playback)······························· 46
Repeat Playback Between Specified Points (A-B Repeat)·········· 46
Playing Back in Your Preferred Order (Program Playback)·········· 47
Switching Audio·········································································· 47
Changing the Subtitles and Subtitle Style·································· 48
Switching the Angle···································································· 49
Changing the Brightness of the Display (Dimmer Control)······ 49
Playback
Introduction·················································································· 36
Before Playing a Disc·································································· 36
Before Playing a SD Memory Card············································· 36
About Playback Information························································ 36
Information Bar Display······························································· 36
Media Player Display··································································· 37
Playing BD and DVD-Video························································· 37
Playing Back Super Audio CD····················································· 39
CD Playback·················································································· 39
DVD-Audio Playback···································································· 39
Playing Back High-Quality Audio················································ 40
(Pure Direct Function)·································································· 40
File Playback················································································· 40
File Playback················································································ 41
About Screen Display During Playback······································· 42
Operation During Playback························································· 42
About Copyright Protection Technology··································· 50
Trademark Information································································ 50
Language Code List······································································ 51
Country Code List········································································ 52
Explanation of Terms··································································· 53
Index······························································································ 54
Troubleshooting································································ 55
Specifications····································································· 57
1
ENGLISH
Getting Started
Features
2Universal Blu-ray Disc player that plays Super
Connections
Audio CD and DVD-Audio formats
Getting Started
2HDMI control ready
vpage 49 “HDMI Control Function”
vpage 3, 4 “Playable Media”
2The unit incorporates design concepts of the
Setup
MARANTZ Super Audio CD Player, and produces
higher sound quality from analog audio output by
the application of MARANTZ design know-how,
such as HDAM-SA2, use of premium parts, etc.
Playback HDMI Control Function Information
2The decoder handles Dolby TrueHD and DTS-HD
Master Audio, of course, as well as Dolby Pro Logic
gx and DTS Neo:6 decoding
Compatible with Linear PCM 192 kHz (one of the BD audio formats)
and multi-channel output (6-ch).
vpage 18 “Connecting to a Device with an Analog Multichannel Audio Input Terminal”
22-channel analog balanced transmission circuit
2Newly developed “Mechanism” with low center
of gravity, vibration damping, quietness and high
accuracy
23-block construction chassis thoroughly prevents
Thank you for purchasing this MARANTZ product. To ensure proper
operation, please read these owner’s manual carefully before using
the product.
After reading them, be sure to keep them for future reference.
Graphical User Interface
Use this manual in combination with the operating guide
displayed on the GUI screen.
GUI Menu Operation (vpage 24)
mutual electrical and magnetic interference
Accessories
Check that the following parts are supplied with the product.
q Remote control........................................................................ 1
w AAA/R03 batteries.................................................................... 2
e Power cord............................................................................... 1
r Audio cable.............................................................................. 1
t Video cable.............................................................................. 1
y Owner’s manual....................................................................... 1
installed
q
Troubleshooting
By combining with the AV8003/MM8003, balanced transmission
is enabled from the player’s D/A converter up to power amplifier.
w
vpage 20 “Connecting to a Device with Analog 2-channel
Audio Input Terminal with Balanced Cable”
2AV Pure Direct playback eliminates mutual
Specifications
interference of audio and video
Separate audio and video output from two HDMI terminals.
Performs clear signal transmission with minimal interference
between signals.
vpage 14 “e “AV Pure Direct” Connection”
2GUI installed with excellent operability and
visibility
vpage 24 “GUI Menu Operation”
2
r
t
ENGLISH
b
Wall
Do not place the UD9004 on an amp or other piece of equipment that
generates heat.
Opening and closing the front panel door
When you want to use the controls behind the front panel door, open
the door by gently pressing on the lower part of the panel. Keep the
door closed when not using these controls.
•Cautions on using mobile phones
Using a mobile phone near this unit may result in noise. If so, move
the mobile phone away from this unit when it is in use.
–
Playable
region codes
Include region
DVD-Audio
DVD-Video
–
z1,z2
BD
1
DVD-V
–
DVD
–
–
SA-CD
–
–
CD
CD
CD-R
CAUTION
•Be careful not to pinch your fingers between the door and the
panel.
CD-RW
z1 : BD-Video/DVD-Audio/DVD-Video discs may not operate as
described in this manual due to menu structure.
z2 : The BD player and BD-Video disc, and DVD player and DVDVideo disc each have their region codes (code assigned for
each region). Playback is not possible if the codes do not
match.
3
Specifications
Video
mode,
AVCHD
format
Troubleshooting
Super Audio
CD
Include region
ALL
Symbols
Used
in this
Owner’s
Manual
DVD-A
–
z1
DVD-RW,
DVD+RW
•About Care
•Wipe the cabinet and control panel clean with a soft cloth.
•Follow the instructions when using a chemical cleaner.
•Benzene, paint thinner or other organic solvents as well as
insecticide may cause material changes and discoloration if brought
into contact with the unit, and should, therefore, not be used.
•Note that the illustrations in these instructions may differ from the
actual unit for explanation purposes.
BD-Video
z1,z2
DVD-R,
DVD+R
•Moving the unit
Be sure to remove a disc, turn off the power and unplug the power
cord from the power outlet. Next, disconnect the connection cables
to other system equipment before moving the unit.
•Sufficiently ventilate the place of installation
If the unit is left in a room full of the smoke from cigarettes, etc.,
for long periods of time, the surface of the optical pickup could get
dirty, in which case it will not be able to read the signals properly.
Playable Media
Playable
formats/
modes
Playback HDMI Control Function Information
•About Condensation
If the UD9004 unit is moved from a cold place to a warm place, or
installed in a room subject to rapid temperature rise from a heater,
etc., condensation (dew) may form on the internal parts of the unit
(operating parts and lenses).
If used in this condition, the UD9004 will not operate correctly and
damage may result. If condensation is formed on the unit, leave the
UD9004 unit for1 to 2 hours with the power OFF before use.
b
Discs
b
bbNote
Playable Media
Setup
•Image persistence (image burn-in)
Do not leave the still images of the disc menu, UD9004 menu, etc.,
displayed on the TV screen for long periods. This can result in image
persistence (image burn-in) on the screen.
Note:
For proper heat dispersal, do not install this unit in a confined
space, such as a bookcase or similar enclosure.
Connections
•Before turning the power switch on
Check once again that all connections are correct and that there are
no problems with the connection cables.
•Power is supplied to some of the circuitry even when the unit is
set to the standby mode. When traveling or leaving home for long
periods of time, be sure to unplug the power cord from the power
outlet.
About Media
Cautions on Installation
Getting Started
Cautions on Handling
ENGLISH
Getting Started
About Media
NOTE
Connections
•A disc may not be accessible or play back incorrectly due to audio
and video interruptions, etc., depending on the recording conditions
when recorded with a BD recorder or DVD recorder.
•Unfinalised DVD-R/-RW/+R/+RW, and CD-R/-RW discs may not play
back. Finalise discs before playing.
Setup
Playback HDMI Control Function Information
The following discs will not play back on this unit.
•BD-RE Ver1.0 (BD disc with cartridge)
•BD-ROM/BD-R/BD-RE discs containing recorded movie, still image,
audio, etc., files
•BD-R/BD-RE in which BDMV/BDAV is recorded
•HD DVD
•DVD-RAM
•CDV (Only the audio part can be played)
•CD-G (Only the audio signals can be output)
•Non-standard CD (CD with copy protection, etc.)
•Unauthorised disc (Pirated disc)
•Disc with recording area less than 55 mm in diameter
•Video Single Disc (VSD) / CVD/ Video CD / Super Video CD /
CompactDisc-Interactive (CD-I) / Photo CDs
SD Memory Cards
Files
Symbols
Used
in this
Owner’s
Manual
Playable cards
SD Memory Card
(8 MB ~ 2 GB)
Playable Media
Playable files
(Symbols Used in this
Owner’s Manual)
MP3
SDHC Memory Card z1
(4 GB)
miniSD Card z2
(8 MB ~ 2 GB)
SD
microSD Card z2
(8 MB ~ 2 GB)
WMA
AAC
miniSD Card
DVD
CD
LPCM
JPEG
DivX
·· Data recorded for BD BONUS
VIEW use
·· See
“Files”
in
“Playable
Media” (vpage 4) for more
information on files.
z1 : This unit supports SD Memory Card with FAT16 file system,
and SDHC Memory Card with FAT32 file system.
z2 : For miniSD Card and microSD Card adapter is necessary.
miniSD Card
Adapter
DVD-R/
Playable
SD
-RW/
files
+R/+RW Memory
(Extension) CD-R/-RW Cards
microSD Card
Adapter
microSD Card
NOTE
Troubleshooting
•This unit does not support mini SDHC and micro SDHC Memory
Card.
•Insert or remove a SD Memory Card while the power is in standby.
If you insert a SD Memory Card while the power is ON, the SD
Memory Card may not be read.
•The SD card used for the Bonus View function must have a capacity
of 1GB or greater. Also the SD card must be initialized on the
UD9004 (vpage 32).
File specification
SD
Specifications
MP3
(.mp3)
S
S
WMA z
(.wma)
S
S
AAC z
(.m4a)
S
S
LPCM
(.wav)
S
S
JPEG
(.jpg/.jpeg)
S
S
DivX®
(.avi/.divx)
S
S
•Sampling frequency:
44.1 kHz, 48 kHz
•Bit rate:
64 kbps ~ 320 kbps
(144 kbps
non-compatible)
•Audio type:
MPEG 1 Audio Layer 3
•Sampling frequency:
44.1 kHz, 48 kHz
•Bit rate:
48 kbps ~ 192 kbps
•Audio type:
WMA Version 9
•Sampling frequency:
44.1 kHz, 48 kHz
•Bit rate:
64 kbps ~ 192 kbps
(Variable Bit Rate non
compatible)
•Audio type:
AAC
•Sampling frequency:
44.1 kHz, 48 kHz
•Bit length: 16 bit
•Number of channels: 2 ch
•Maximum resolution:
4,096 x 4,096 pixels
•Minimum resolution:
32 × 32 pixels
•Maximum file size: 12 MB
•Compatible versions:
Up to DivX® 6
•Maximum size: 2 GB
Symbols
Used
in this
Owner’s
Manual
MP3
WMA
AAC
LPCM
JPEG
DivX
z : This unit cannot play back files recorded under DRM (Digital
Rights Management) other than DivX® files.
4
•The abovementioned file type may also fail to play back depending
on conditions at the time of recording.
•If characters not supported on the menu screen are included in a
file name, title, artist name or album title, those are not displayed
correctly.
•JPEG format images stored in progressive format cannot be played
back.
ENGLISH
nn Super Audio CD
CDs are divided into several sections (tracks). These sections are
all allotted numbers, called the track numbers.
Single layer Super Audio CD with
only an HD layer z.
HD layer
•Dual layer disc
Two-layer Super Audio CD with an
HD layer z and a CD layer.
The signals on the CD layer can
be played on a regular CD player.
No
About Discs and Files
nn BD-Video, DVD-Video
BD/DVD-Video discs are divided into several large sections (titles)
and small sections (chapter). These sections are all allotted
numbers, called the title numbers and chapter numbers.
BD,
DVD
BD、
DVD
Title1
タTitle2
イトル2
タイトル 1
Chapter
チャプター11 Chapter
チャプター22 Chapter
チャプター11 Chapter
チャプター22 Chapter
チャプター33
Track4
Track5
CD layer HD layer
z : All Super Audio CDs contain an HD (High Density) layer with high
density Super Audio CD signals. This layer can contain a stereo
channel area, a multi-channel area, or both a stereo channel and
multi-channel area.
nn DVD-Audio
DVD-Audio discs are divided into several large sections (groups)
and small sections (tracks). These sections are all allotted numbers,
called the group numbers and track numbers.
MP3/WMA/AAC/LPCM/JPEG/DivX® files recorded on DVD-R/RW/+R/+RW, CD-R/-RW and SD Memory Card are divided into large
segments (folders) and small segments (files). Files are stored in
folders, and folders can be placed for storage in a hierarchy. The
UD9004 can recognize up to 8 hierarchies of folder.
DVD-R/-RW/+R/+RW, CD-R/-RW
or SD Memory Card
DVD-R/-RW、CD-R/-RWまたはSDカード
Folder1
Folder2

File4

File1


File5


File6

File2
File3


File7

Folder3
1st level
2nd level
3rd level
SMDemory Card
When writing MP3/WMA/AAC/JPEG/DivX® files on a CD-R/-RW disc,
set the writing software’s format to “ISO9660”. The files may not play
properly if they are recorded in other formats. For details, refer to the
instructions of your writing software.
DVD-Audio
Track1
Track2
Group2
Track3
Track1
Specifications
Group1
Troubleshooting
GExampleH
Track3
Playback HDMI Control Function Information
•Hybrid disc
one of your 3 views now?
Yes
Track2
nn File
Super Audio CD with a double HD
layer z, offering extended playing
time and high sound quality.
HD layer
Track1
Setup
Use 0, 1 buttons to select “Yes”
if you want to play back the file, or
to select “No” if you do not want
to play it back. The press ENTER
button to confirm the selection.
nn CD
GType of Super Audio CDH
•Single layer disc
Connections
•When you purchase or rent a DivX® file through the official site
of DivX® Video-On-Demand (VOD) services, a UD9004 registration
code is required. For details, see “DivX® Registration” (vpage
31).
DivX Authorization Error
•A DivX® VOD file recorded with a
Authorization Error.
This player is not authorized
different code from the UD9004
to play this video.
registration code cannot be played
back.
•Some DivX® VOD files are restricted
OK
with limited playable times. If your
DivX® VOD file has such a limit,
DivX Rental
the number of playable times is
View DivX(R) VOD Rental
®
displayed on the DivX VOD display
This rental has 3 views left.
screen.
Do you want to use
Getting Started
About Media
About DivX® Video-on-Demand (VOD)
Track2
5
ENGLISH
Getting Started
About Media
Cautions on Using Media
Connections
Setup
Playback HDMI Control Function Information
Inserting a Disc
About Handling of Media
Cleaning Discs
•Set the disc with the labeled side facing up.
•Make sure the disc tray is fully open when inserting the disc.
•Place the disc horizontally in the tray, aligned with the tray guide.
•Do not get fingerprints, oil or dirt on discs.
•Take special care not to scratch discs when removing them from
their cases.
•Do not bend or heat discs.
•Do not enlarge the hole at the center.
•Do not write on the labeled (printed) surface with ball-point pens,
pencils, etc., or stick new labels on discs.
•Water droplets may form on discs if they are moved suddenly from
a cold place (outdoors for example) to a warm place, but do not try
to dry them off using a hairdryer, etc.
•Do not eject an SD Memory Card or turn off the UD9004’s power
while the card content is in playback. This may result in malfunction
or loss of the card’s data.
•Do not attempt to open or modify SD Memory Cards.
•SD Memory Cards and files can be damaged by static electricity.
Do not touch the metal contacts of an SD Memory Card with your
fingers.
•Do not use warped SD Memory Cards.
•After use, be sure to remove any disc or SD Memory Card, and store
it in its proper card case, to avoid dust, scratches and deformation.
•Do not store discs in the following places:
1.Places exposed to direct sunlight for long periods of time
2.Dusty or humid places
3.Places exposed to heat from heating appliances, etc.
•If there are fingerprints or dirt on discs, wipe them off before using
the disc.
•Use a commercially available disc cleaning set or a soft cloth to
clean discs.
If a disc that cannot be played is loaded or the disc is loaded
up-sidedown, “NO DISC” is displayed on the player’s display.
NOTE
•Only load one disc at a time. Loading two or more discs can damage
the unit or scratch the discs.
•Do not use cracked or warped discs or discs that have been repaired
with adhesive, etc.
•Do not use discs on which the sticky part of cellophane tape or
labels is exposed or on which there are traces of where labels have
been removed. Such discs can get caught inside the player and
damage it.
•Do not use discs with special shapes, as they could damage the
player.
Troubleshooting
•Do not push the disc tray in by hand when the power is turned off.
Doing so could damage the set.
Inserting an SD Memory Card
Specifications
•Insert an SD Memory Card in the direction of the arrow into the SD
CARD slot with the label facing up.
•Insert the card straight into SD CARD slot until it clicks.
•To remove the card, push it in the direction of insertion, and then
release to eject.
6
Gently wipe the disc from the
inside towards the outside.
Do not wipe with a circular
motion.
NOTE
Do not use record spray, antistatic agents, or benzene, thinner or
other solvents.
About Copyright
•Unauthorised copying, broadcasting, public performance and
lending of discs are prohibited.
•This product incorporates copyright protection technology that is
protected by U.S. patents and other intellectual property rights.
•Use of this copyright protection technology must be authorized by
Macrovision, and is intended for home and other limited viewing
uses only unless otherwise authorized by Macrovision.
Reverse engineering or disassembly is prohibited.
•Portions of this product are protected under copyright law and
provided under license by ARIS/SOLANA/4C.
ENGLISH
Inserting the Batteries
Point the remote control unit at the remote sensor when operating
it.
w
q
e
30°
30°
e Put the rear cover back on.
NOTE
NOTE
The set may function improperly or the remote control unit may not
operate if the remote control sensor is exposed to direct sunlight,
strong artificial light from an inverter type fluorescent lamp or infrared
light.
•If the signal code of the remote control does not match the signal
code of the unit, the remote control code set on the unit is shown
on the display.
GExampleH
If the code setting on the unit is “BD 1”, and the setting on the
remote control is “BD 2”, “BD 1” is shown on the display.
NOTE
Match the signal code of the remote control with the signal code of
the unit. If the remote control code is different, you cannot operate
the UD9004 with the remote control.
Troubleshooting
Specifications
•Use AAA/R03 batteries in this remote control.
•Replace the batteries with new ones if the set does not operate
even when the remote control unit is operated close to the unit.
(The supplied batteries are only for verifying operation.)
•When inserting the batteries, be sure to do so in the proper direction,
following the “q” and “w” marks in the battery compartment.
•To prevent damage or leakage of battery fluid:
Do not use a new battery together with an old one.
Do not use two different types of batteries.
Do not attempt to charge dry batteries.
Do not short-circuit, disassemble, heat or dispose of batteries in
flames.
•If the battery fluid should leak, carefully wipe the fluid off the inside
of the battery compartment and insert new batteries.
•Remove the batteries from the remote control unit if it will not be in
use for long periods.
•Used batteries should be disposed of in accordance with the local
regulations regarding battery disposal.
GRemote control code settingH
•The supplied remote control has two remote control code settings:
BD 1 and BD 2.
•The code is set to “BD 1” at the factory.
•To set the code to “BD 2”, hold the Stop (2) button and the Number
button [2] pressed for more than five seconds.
•To set (return) the code to “BD 1”, hold the Stop (2) button and the
Number button [1] pressed for more than five seconds.
Playback HDMI Control Function Information
Approx. 16.4 ft (5 m)
Switches when the UD9004’s remote control operates another
MARANTZ BD players in the vicinity.
Set the remote control code simultaneously on the main unit, too.
For how to set codes, see GUI menu: “Other Setup” – “Remote
Control Setting” – “Remote ID” (vpage 32).
Setup
Batteries
Remote Control Settings (Remote
Control Side)
Connections
q Remove the remote control w Set three AAA/R03 batteries in
unit’s rear cover.
the battery compartment in the
indicated direction.
Operating Range of the Remote Control
Unit
Getting Started
About the Remote Control Unit
7
ENGLISH
Getting Started
Part Names and Functions
Front Panel
Display
For buttons not explained here, see the page indicated in parentheses ( ).
Connections
Q6
Q5
Q4
Q3
Q0
o
i
u
Setup
q
w
Playback HDMI Control Function Information
qPlayback mode indicators
1 : During Playback
3 : During pause and step-by-step playback
PROG : During program playback
RAND : During random playback
1 A-B : During repeat playback
wInformation display
qw
e
r t
qPower operation button
(POWER ON/STANDBY)····························· (22)
Troubleshooting
wSTAND BY indicator···································· (22)
eHDMI MODE button···································· (13)
rHDMI RESOLUTION button························ (39)
tPURE DIRECT button, indicator·················· (40)
ySOUND MODE button································· (39)
uSD/DISC button, SD indicator···················· (36)
Specifications
If an SD card is inserted in the SD CARD slot,
and SD is selected with the SD/DISC button on
the front panel, the indicator lights.
iDisplay···························································· (8)
oSD CARD slot················································· (6)
Q0Remote control sensor·································· (7)
8
y
u i o Q0 Q1
Q1Disc tray························································· (6)
Q2Stop button (2)············································ (43)
Q3Play button (1)············································ (39)
Q4Revers-skip/Forward-skip buttons
y
t
Q2
(8, 9)··················································· (43)
Q5Pause/Still button (3)··························· (43, 45)
Q6Disc tray open/close button (5)················· (36)
When power is in standby mode, press Q3 and Q6
to turn the power on.
Displays various information or
elapsed time and so on of the disc.
playback
playing
back
r
uTime mode indicators
TOTAL : Total time of Super Audio CD and CD
SING : Elapsed time of title/chapter/track/file
being played back
REM : Remaining time of title/chapter/track/file
being played back
iGroup/Title/Track/Chapter indicators
oHDMI output indicator
Display when HDMI video or audio signals are
being output.
ePlayback format indicators
rDownmix indicator
Displayed when
permitted audio.
e
downmix
tAngle information indicator
Displayed when a scene on the currently playing
disc has been shot at various angles.
yAudio channel indicators
Displays the number of audio signal channels
during playback.
2CH : 2-channel playback
MULTI : Multi-channel playback
Does not display when the HDMI cable is
not correctly connected and when the HDMI
connection is not verified.
Q0Media indicators
BD : BD
DVD : DVD-Video, DVD-R/+R/-RW/+RW
DVD AUDIO : DVD-Audio
SUPER AUDIO CD : Super Audio CD
CD : CD
SD : SD Memory Card
Displays the inserted media.
ENGLISH
Rear Panel
For buttons not explained here, see the page indicated in parentheses ( ).
Q0
SW
SBR
oi
u
VIDEO OUT S VIDEO OUT
SBL
y
Y
PB/CB
t
PR/CR
Connections
Q1
1
2
Setup
COMPONENT
VIDEO OUT
C
SR
COAXIAL
HDMI OUT
SL
DIGITAL OUT
FR
(AUDIO )
Playback HDMI Control Function Information
(VIDEO)
OPTICAL
NETWORK
FL
7.1ch AUDIO OUT
R
IN
L
OUT
STRAIGHT CABLE
AC IN
MODEL NO. UD9004
FLASHER
RS-232C
2ch AUDIO OUT
Connect an external control device or other device for servicing.
(Use a straight cable for the connection.)
wRS-232C connector
Extension connector for future use.
eNETWORK connector································································(21)
rAC inlet (AC IN)··········································································(22)
tHDMI OUT connectors························································(13, 14)
Signals output from each terminal change depending on the HDMI
mode setting.
e
yCOMPONENT VIDEO OUT connectors····································(19)
uS-VIDEO OUT connector···························································(19)
iVIDEO OUT connector······························································(19)
oDIGITAL OUT OPTICAL/COAXIAL connectors························(17)
Q07.1ch AUDIO OUT connectors··················································(18)
Q12ch XLR AUDIO OUT connectors·············································(20)
r
NOTE
•Do not touch the inner pins of the connectors on the rear panel.
Electrostatic discharge may cause permanent damage to the unit.
•Do not put your finger or foreign object in the fan opening. Doing so
could cause injury or unit failure.
For software recorded in multi-channel, analog signals that have
been down-mixed into 2 channels are output.
9
Specifications
qFLASHER IN/OUT jacks
w
Troubleshooting
q
Getting Started
Part Names and Functions
ENGLISH
Getting Started
Part Names and Functions
Remote Control Unit
For buttons not explained here, see the page indicated in parentheses ( ).
Connections
E1
Setup
E0
W9
W8
W7
W6
W5
W4
W3
W2
W1
q
w
e
Playback HDMI Control Function Information
r
t
y
u
i
o
W0
Q0
Q1
Q2
Troubleshooting
Q9
Q3
Q4
Specifications
Q8
10
Q5
Q6
Q7
q POWER ON/OFF buttons ·························································(22)
w PURE DIRECT button································································(40)
e MODE button ············································································(33)
r RANDOM button·······································································(46)
t AUDIO button ···········································································(47)
y POP UP MENU/MENU button ·················································(37)
u CLEAR button ···········································································(35)
i ENTER button ···········································································(24)
o Cursor buttons (d, f, 0, 1) ··················································(24)
Q0 RETURN button ········································································(24)
Q1 PICT. ADJUST button·······························································(35)
Q2 Fast-reversing button (6) ·····················································(45)
Q2 Fast-forwarding button (7) ··················································(45)
Q2 Revers-skip button (8)·························································(43)
Q2 Forward-skip button (9) ······················································(43)
Q2 Play button (1) ·········································································(39)
Q2 Pause/Still button (3) ························································(43, 45)
Q2 Stop button (2)·········································································(43)
Q3 PROG/DIRECT button (PROG/DIRECT) ··································(47)
Q4 Number buttons (0 ~ 9, +10) ····················································(37)
Q5 CALL button ··············································································(47)
Q6 PAGE + button ··········································································(40)
Q7 SOUND MODE button ······························································(39)
Q8 RED/GRN/YEL/BLU buttons
Q9 SEARCH button ········································································(39)
W0 SETUP button ···········································································(23)
W1 TOP MENU button ····································································(37)
W2 SUBTITLE button ······································································(48)
W3 ANGLE button ···········································································(49)
W4 REPEAT A-B button ··································································(46)
W5 REPEAT button ········································································(46)
W6 DIMMER button ········································································(49)
W7 DISPLAY button ········································································(36)
W8 HDMI RESOLUTION button ·····················································(15)
W9 HDMI MODE button ·································································(13)
E0 OPEN/CLOSE button (5) ·························································(36)
E1 Remote control signal transmitter ············································(7)
• When power is in standby, press E0 and Q2 (1) to turn the power
on.
• You can use Q8 when operating the BD popup menu screen, etc.
ENGLISH
Getting Started
Connections
Connect the UD9004 as follows before using. Make connections according to the equipment you are connecting.
Some UD9004 settings may be necessary depending on the connection method. Check each connection item for more information.
Back with a Direct
2 Playing
Connection to a TV
vpage 19
3 Playing
Audio
Back 2-Channel
Connections
vpage 13
Theater Playback
1 Home
– Playing Back Using Multi-Channel System –
vpage 20
UD9004
UD9004
Setup
•HDMI connection (vpage 14)
UD9004
or
Audio
•Analog audio connection (vpage 19)
Video
•Analog video connection (vpage 19)
Multi-channel Audio + Video
•HDMI connection
“Using an HDMI Cable to Connect to an AV Amp or Television” (vpage
13)
or
•Digital audio connection
“Connection to an AV Amp with No HDMI Audio Input” (vpage 17)
•Analog 7.1ch connection
“Connecting to a Device with an Analog Multi-channel Audio Input
Terminal” (vpage 18)
vpage 20
•2ch stereo pin plug cable (unbalanced) connection
“Connecting to a Device with Analog 2-channel Audio
Input Terminal with Stereo Pin Plug Cable” (vpage 20)
UD9004
to the UD9004’s
5 Upgrading
Latest Software Version
vpage 21
Video
UD9004
•Connecting the Power Cord
•Once Connections are Completed
vpage 22
•LAN connection
“Connecting to the Network” (vpage 21)
11
Specifications
•Digital output
“Connecting to a Digital Recording Device” (vpage
20)
To output sound from a disc while maintaining the same sound quality
as the disc sound, some settings of Audio Setup are disabled as default
(vpage 25 ~ 27).
To enable the settings of Audio Setup, set Source Direct to “Off”
(vpage 26).
•Analog video connection
“Connection to an AV Amp with No HDMI Video Input” (vpage 19)
Troubleshooting
Multi-channel Audio
4
Recording a CD
•2ch balanced connection
“Connecting to a Device with Analog 2-channel Audio
Input Terminal with Balanced Cable” (vpage 20)
or
Playback HDMI Control Function Information
Audio + Video
ENGLISH
Getting Started
Preparation
Cables Used for Connections
NOTE
Prepare the cables to match the devices you are to use.
Connections
Video cables
Audio and video cables
HDMI connections
(Sold separately)
19-pin HDMI cable
Component video
connections
(Y)
(Sold separately)
(PB/CB)
Setup
Audio cables
Playback HDMI Control Function Information
Coaxial
digital
connections
(Sold separately)
(PR/CR)
Component video (75 Ω/ohms) cable
Coaxial digital (75 Ω/ohms pin-plug) cable
S-Video
connections
(Sold separately)
Optical
digital
connections
Video connections
Optical cable
(Sold separately)
(Included)
Analog connections
(balanced)
Network
connections
Balanced cable
(1 included)
L
L
R
R
Stereo pin plug cable
Analog connections
(center, subwoofer)
Troubleshooting
(Sold separately)
Specifications
12
75 Ω/ohms pin-plug video cable
Other cables
(Sold separately)
Analog connections
(stereo, surround)
S-Video cable
Pin-plug cable
(Sold separately)
Ethernet cable
•Do not plug the power cord into the power outlet until all connections
are completed.
•Be sure to read the owner’s manuals for the connected devices.
•First check the connection channels, and then correctly connect the
input and output channels.
•Do not bundle the power cord together with the connection cables.
This can result in noise.
•Use only HDMI (High Definition Multimedia Interface) cable that
bears the HDMI logo (genuine HDMI product). Using cable without
the HDMI logo (non-genuine HDMI product) may result in abnormal
playback.
•When outputting deep colour or 1080p, etc., we recommend you
use High Speed HDMI cable for enhanced high-quality playback.
ENGLISH
Using an HDMI Cable to Connect to an AV Amp or Television
Used for multi-channel
playback using 2 devices.
Video + Audio
Video + Audio
Used for multi-channel
w HDMI Auto (Independent) playback using one device
and 2-channel playback
(HDMI Inde.)
using the other unit. (z1)
Video + Audio
Video + Audio
e AV Pure Direct
(AV P.Direct)
Used for the highest
quality playback using
different HDMI cables to
connect video and audio
separately.
Video
Audio
r HDMI1
t HDMI2
Used for connecting only
1 device.
Video + Audio
Does not output
Does not output
Video + Audio
y HDMI Off
Used
when
HDMI
connection is not used.
Does not output
Does not output
NOTE
nn About Audio Format to be Output
Specifications
To disable video or audio output from the HDMI terminal, set “Video Out” of “Pure Direct Setup”, which
outputs high quality analog audio to “Off”. To enable the HDMI signal output, set the Pure Direct mode
to one of the following setting:
•Pure Direct mode “Off” or “User Preset 1” or “User Preset 2” (b)
(“Playing Back High-Quality Audio (Pure Direct Function) ” vpage 40)
bbDo this after setting “Pure Direct Setup” – “User Preset 1” or “User Preset 2” – “Video Out” on GUI
menu to “On” (vpage 30).
nn About Audio Signal
(1) Check audio signals that can be input by the device to be connected.
•Audio format·∙·∙·∙·∙·∙·∙·∙·∙·∙·∙·∙·∙·∙·∙Bit stream (Dolby Digital, DTS etc.), Linear PCM, etc.
•Number of channels
(2) About number of output channels of multi-channel audio
When outputting bitstream signals to two HDMI devices, the signals are output to both HDMI devices
if they both support bitstream signals. Of only one device support bit stream, LPCM is output to the
device, which does not support bit stream.
When outputting LPCM signals to two HDMI devices, it is not possible to output multi-channel audio
signals with different numbers of channels to the two HDMI devices.
When the number of channels of multi-channel audio supported by the connected 2 HDMI devices
are different, the audio signal output to each mode becomes as follows:
•HDMI Auto (Dual) :
Outputs multi-channel audio of less number of channels to both devices.
If the supported number of channels is 7.1 channel and 5.1 channel, respectively, 5.1 channel audio
is output. If the supported number of channels is multi-channel and 2-channel (or 2.1-channel), multichannel and 2-channel are output.
•HDMI Auto (Independent) :
Multi-channel audio is output as is to the device, which supports more number of channels.
LPCM audio of 2-channel is output to the other device.
We recommend you use this mode when outputting to both an AV Amp and TV.
Troubleshooting
z1 : If the number of channels supported by 2 devices is the same, multi-channel audio is output
to both devices.
When “About HDMI Video Resolution Setting” (vpage 15) is set to “Auto”, of the resolution
supported by both of the 2 connected devices, the UD9004 outputs the highest resolution video
signal to both devices.
Playback HDMI Control Function Information
q HDMI Auto (Dual)
(HDMI Dual)
Output signal from each terminal
HDMI OUT 1
HDMI OUT 2
nn About Video Signal
Setup
HDMI mode
Video and Audio Output Signal when Outputting to 2 HDMI Devices
(HDMI Auto (Dual) Mode and HDMI Auto (Independent) Mode)
Connections
•There are 5 ways to connect (q – t) using HDMI cable (sold separately). Configure appropriate
connection for HDMI mode first and then set HDMI mode using HDMI MODE button.
•When connecting with HDMI cable, perform the settings in “Required Settings for HDMI
Connection” (vpage 15).
•UD9004 automatically detects audio/video signal supported by the connected HDMI device and
outputs the signal. To change the setting, see “HDMI Setup” on the GUI menu (vpage 25, 26).
Default settings are underlined.
Getting Started
1. Home Theater Playback – Playing Back Using Multi-channel System –
Audio format supported by 2 connected HDMI devices is output.
When multi-channel audio is output, the output channel is as described above (2).
13
ENGLISH
Getting Started
1. Home Theater Playback – Playing Back Using Multi-channel System –
q “HDMI Auto (Dual)”, w “HDMI Auto (Independent)” connection
Connections
AV Amp 1 or
TV 1
AV Amp 2 or
TV 2
HDMI
IN
HDMI
IN
Setup
Playback HDMI Control Function Information
e “AV Pure Direct” connection
TV
AV Amp
HDMI
IN
HDMI
IN
nn About Video Signal
Troubleshooting
When “About HDMI Video Resolution Setting” (vpage 15) is set to “Auto”, of the resolution
supported by both connected devices, the video signal of the highest resolution is output to both
devices. (From the HDMI 2 terminal, audio signal and black video signal are output.)
r “HDMI 1”, t “HDMI 2” Connection
GExampleH “HDMI 1” connection
Specifications
AV Amp or
TV
HDMI
IN
y During “HDMI Off”
Audio/video is not output from the HDMI terminal.
14
nn Connection to a device with a DVI-D terminal
If you use a HDMI/DVI-D conversion cable (sold separately), HDMI video signals are converted to DVID signals, enabling connection to a device with a DVI-D terminal.
NOTE
•In this case, the audio signal is not output. Make the appropriate audio connections for your devices.
(vpage 15 ~ 21).
•The video signal will be in RGB format.
•You cannot output to a DVI-D device that does not support HDCP (high-bandwidth digital content
copyright protection system).
•Video may not be output depending on the combination of devices.
ENGLISH
Setting HDMI Audio Output
Required Settings for HDMI Connection
Setting HDMI Video Output
“HDMI Setup” (vpage 25, 26)
nn Make the Video Output Signal Setting for the Connected Television
“Video Setup” (vpage 26)
Auto
Bron direct
480/576i
(Auto)
(Source Direct)
(480/576 interlaced)
1080P24
(1080 progressive, 24-frame)
1080P
(1080 progressive)
1080i
(1080 interlaced)
480/576P
(480/576 progressive)
About output signal and speaker settings
Auto
UD9004 outputs a bitstream signal that is decoded by the
connected device.
bbIn this case, you cannot make a speaker setting for HDMI
audio with the UD9004.
Make the setting with the connected device.
bbWhen outputting the Dolby TrueHD or DTS-HD audio,
press MODE button and set “BD Audio Mode” to “HD
Audio Output” (vpage 33).
720P
Outputs multi-channel Linear PCM audio signals with
speaker setting by the UD9004.
bbFor speaker setting, on the GUI menu, “Audio Setup”
– “7.1ch Audio Out” – “Multi Channel” – “Speaker
Configuration” (vpage 27).
(720 progressive)
Device compatible with
multi-channel HDMI audio
input, but not capable of
speaker setting for each
channel
Multi LPCM
BM On
NOTE
Device compatible with
multi-channel HDMI audio
input, and capable of
speaker setting for each
channel
Multi LPCM
BM Off
Output of multi-channel Linear PCM audio signals from the
UD9004.
Perform the speaker setting with the connected device.
bbBM : Bass Management (means multi-channel speaker
setting)
Device compatible with 2channel HDMI audio input
2ch
Downmixed 2-channel Linear PCM audio signals are output
from the UD9004.
Perform the speaker setting with the connected device.
Device not compatible with
HDMI audio signal input
Mute
Audio signal are not output from the UD9004’s HDMI
terminal.
Only video signals are output from the HDMI terminal.
bbMake the audio connection.
15
Specifications
When the HDMI video resolution is set to “1080P24”, HDMI video signals are output from the UD9004
with a resolution of 1080P and a frame rate of 24 frames per second, regardless of the video signals on
the disc being played. Because of this, when playing discs containing video signals recorded with a frame
rate of something other than 24 frames per second, the movement of the picture may be unnatural. If this
happens, set the HDMI video resolution to something other than “1080P24”.
To output sound from a disc while maintaining the same
sound quality as the disc sound, some settings of Audio
Setup are disabled as default (vpage 25 ~ 27).
To enable the settings of Audio Setup, set Source Direct
to “Off” (vpage 26).
bbBM : Bass Management (means multi-channel speaker
setting)
Troubleshooting
•If the HDMI resolution is not set to “Auto”, set it to correspond with the resolution of your television.
Images will not be projected normally if the television resolution and UD9004’s output resolution do
not match.
•Audio and video will be temporarily interrupted if the power of the connected device currently playing
back is turned off, or input is switched.
•When you change the HDMI video resolution of the UD9004, it takes from a few seconds up to about
10 seconds for validation between the UD9004 and the connected device. Audio/video is not output
during this period.
•When outputting deep colour or 1080p, etc., we recommend you use High Speed HDMI cable for
enhanced high-quality playback.
Playback HDMI Control Function Information
•Change the HDMI video resolution by pressing HDMI RESOLUTION button. Switch the output mode as
follows. Default settings are underlined.
Device with the following
built-in decoder
·· Dolby TrueHD
·· Dolby Digital Plus
·· Dolby Digital
·· DTS-HD
·· DTS
Setting items
Setup
nn About HDMI Video Resolution Setting
Device to be connected
Connections
nn Make HDMI Output Signal and HDMI Control Function Settings
•When you press SET UP button and set “HDMI Setup” – “Audio Setup” to “Auto” (vpage 25) on the
GUI menu, audio mode is set according to the connected device.
•When you want to set the HDMI audio output separately, change according to the following table.
•Refer to the owner’s manual of the connected device regarding HDMI audio input specifications
compatible with the connected device.
Getting Started
1. Home Theater Playback – Playing Back Using Multi-channel System –
ENGLISH
Getting Started
1. Home Theater Playback – Playing Back Using Multi-channel System –
nn Audio signal from the HDMI output terminal
Connections
You can change the audio format and playback number of channels according to the specifications of
the device to which the UD9004’s HDMI audio output signals are input. Make settings while checking
the specifications of the audio device to be connected as well as the audio format/number of channels
stored in media and files for playback.
Media/Files
Audio format
Setting “HDMI Setup” – “Audio Setup” (vpage 25) on
the GUI menu
Setup
Auto
Playback HDMI Control Function Information
BD
AVCHD
DVD-Video
DVD-Audio
Dolby Digital
Dolby Digitalz1
Dolby Digital Plus
Dolby Digital Plusz1
Dolby TrueHDz1
Dolby TrueHD
DTS
DTSz1
DTS-HD
DTS-HDz1
LPCM
Multi LPCM
Dolby Digital
Dolby Digital
LPCM
Multi LPCM
Dolby Digital
Dolby Digital
DTS
DTS
LPCM, MPEG
2 ch LPCM
LPCM, PPCM
Multi area
Troubleshooting
Super audio CDz2 Stereo area
CD layer
DivX®
Dolby Digital
MP3, MP2
CD, MP3, WMA, AAC, LPCM
Specifications
DTS-CD
Multi LPCM
BM On/Off
2ch
Multi LPCM
2 ch Downmix
LPCM
Multi LPCM
2 ch Downmix
LPCM
2 ch Downmix
LPCM
Multi LPCM
2 ch LPCM
Dolby Digital
Multi LPCM
2 ch Downmix
LPCM
Multi LPCM
2 ch Downmix
LPCM
2 ch LPCM
DTS
z1 : Multi LPCM signals are output when “BD Audio Mode” is set to “Mix Audio Output ” (vpage 33).
Multi LPCM signals are output when outputting HDMI video signals with resolutions of 480i/576i or
480p/576p.
z2 : Super Audio CD audio signals are output at 44.1 kHz 16-bit.
16
Even if “HDMI Setup” – “Audio Setup” on the GUI menu is set to “Auto” (vpage 25), multilinear PCM
or downmixed 2-channel linear PCM signals are output if a device that does not support bitstreams is
connected.
Copyright protection system
In order to play back digital video and audio such as BD-Video or DVD-Video via HDMI connection,
both the player and TV or the AV Amp need to support the copyright protection system known as
HDCP (High-bandwidth Digital Content Protection System). HDCP is copyright protection technology
comprised of data encryption and authentication of the connected AV device. The UD9004 supports
HDCP.
NOTE
•If a device that does not support HDCP is connected, video and audio are not output correctly. Read the
owner’s manual of your television or AV Amp for more information.
•The audio signal from the HDMI output terminal (sampling frequency, number of channels, etc.) may
be limited by the HDMI audio specifications of the connected device regarding permissible inputs. For
example, if the HDMI audio specification of the connected device is 5.1 channels, 5.1-channel audio
will be automatically output even when playing back 7.1 channels by the UD9004. In this case, analog
audio output will also be 5.1-channel.
•Audio signal input may not be supported depending on the HDMI compatible monitor (projector, etc.)
being used.
When the UD9004 is connected to this kind of device, audio signals are not output from the HDMI
terminal.
ENGLISH
Connection to an AV Amp with No HDMI Audio Input
When playing back Dolby Digital Plus/Dolby TrueHD/DTS-HD audio recorded on a BD disc, the UD9004
outputs Dolby Digital or DTS bitstream from its digital audio output terminal.
Audio Signal from the Digital Audio Output (Optical/Coaxial) Terminal
The UD9004 can convert and output digital audio signal format recorded on media.
Convert the digital audio signal in accordance with the specifications of the device that is to input digital
audio output signals from the UD9004.
AUDIO
Media/Files
COAXIAL
IN
PCM/PCM Down Sampling
Dolby Digital
BD
NOTE
Dolby TrueHD
DTS
DTS-HD
AVCHD
DVD-Video
2 ch Downmix LPCMz1
Dolby Digital
Dolby Digital
LPCM
2 ch Downmix LPCM
Dolby Digital
Dolby Digital
DTS
DTS
LPCM, PPCM
Multi area
Super Audio CD
Stereo area
2 ch Downmix LPCM
2 ch Downmix LPCM
Audio is not output
CD layer
2 ch LPCM
Dolby Digital
Dolby Digital
Troubleshooting
DivX®
DTSz1
LPCM
LPCM, MPEG
DVD-Audio
Dolby Digitalz1
Playback HDMI Control Function Information
Dolby Digital Plus
2 ch Downmix LPCM
MP3, MP2
CD
2 ch LPCM
MP3, WMA, AAC, LPCM
DTS
2 ch Downmix LPCM
(DTSz2)
z1 : Bitstream signals are output in accordance with the BD re-encode setting when “BD Audio Mode”
is set to “Mix Audio Output” (vpage 33).
z2 : When “HDMI Setup” – ”Audio Setup” is set to “Auto” on the GUI menu and bit stream is output from
HDMI , the DTS bit stream is output from the digital audio output (optical/coaxial) as well.
For content with copyright protection, audio signal is down sampled to 48kHz 16bit and is output.
17
Specifications
DTS-CD
Setup
Bitstream
OPTICAL
IN
•Dolby TrueHD/Dolby Digital Plus/DTS-HD audio signals are not output with
this connection.
When outputting Dolby TrueHD/Dolby Digital Plus/DTS-HD audio signals, do
so with an HDMI connection (vpage 13, “Using an HDMI Cable to Connect
to an AV Amp or Television”).
Match the
•Super Audio CD’s DSD signal cannot be output. Also, during CD layer
shapes
playback, 44.1 kHz/16-bit Linear PCM is output.
•Do not output DTS audio signals to an AV Amp that does not support DTS. Playing back a BD/DVD
disc with recorded DTS content can generate noise and even damage your speakers.
•When connecting with an optical transmission cable (sold separately), make sure the plug shape
aligns with the socket, and insert fully.
Audio format
Setting “Audio Setup” – “Digital Out” (vpage 29) on
the GUI menu
Connections
AV Amp
Getting Started
1. Home Theater Playback – Playing Back Using Multi-channel System –
ENGLISH
Getting Started
1. Home Theater Playback – Playing Back Using Multi-channel System –
Connecting to a Device with an Analog Multi-channel Audio
Input Terminal
Connections
Outputs multi-channel audio decoded by the UD9004.
If your audio system has an analog multi-channel audio input terminal, connect using audio cable (sold
separately).
Setup
AV Amp
AUDIO
SUBWOOFER
Playback HDMI Control Function Information
SURROUND BACK
L
L
L
R
R
R
In the case of a 5.1-channel
connection, you need not
connect the SBR/SBL terminals.
In this case, on the GUI menu,
select “Audio Setup” – “7.1ch
Audio Out” – “Multi Channel” –
“Speaker Configuration” – “Surr.
Back”, and set “Size” to “None”
(vpage 27).
CENTER
SURROUND
L
L
L
R
R
R
FRONT
L
L
L
R
R
R
Troubleshooting
To output sound from a disc while maintaining the same sound quality as the disc sound, some
settings of Audio Setup are disabled as default (vpage 25 ~ 27).
To enable the settings of Audio Setup, set Source Direct to “Off” (vpage 26).
Specifications
18
Connection to an AV Amp with No HDMI Video Input
Check the video terminals and make the connection to one of them.
AV Amp
VIDEO
VIDEO IN
S VIDEO IN
COMPONENT
VIDEO IN
Y
PB
PR
ENGLISH
Check the television’s audio and video terminals and make the connection to one of them.
Audio terminals
Video terminal
S video input
terminal
TV
TV
TV
TV
TV
VIDEO
VIDEO
VIDEO
AUDIO
IN
L
VIDEO
IN
S VIDEO
IN
COMPONENT VIDEO
IN
HDMI
IN
PR
nn When connected to the HDMI input terminal
Outputting both digital video and digital audio signals.
See “Required Settings for HDMI Connection” (vpage 15) for HDMI video output and audio output
settings.
L
(supplied)
(Sold
separately)
(Sold
separately)
(Sold
separately)
Playback HDMI Control Function Information
(supplied)
R
PB
Setup
R
Y
•The UD9004’s component video output supports 480i/576i/480p/576p/720p/1080i output. Match the
output to the corresponding resolution of the connected television by setting, on the GUI menu: “Video
Setup” – “Component Resolution” (vpage 26). Images will not be projected normally if the television
resolution and UD9004’s output resolution do not match. Copyright protected DVD is output in 480i/576i
or 480p/576p.
Connections
HDMI input
terminal
AUDIO
R
nn When connected to the television’s component video input terminal
Component video
input terminal
Getting Started
2. Playing Back with a Direct Connection to a TV
L
Troubleshooting
When outputting the UD9004’s analog 2-channel audio to the television’s 2-channel (stereo) audio
input terminal, on the GUI menu, select “Audio Setup” – “7.1ch Audio Out”, and set it to “2 Channel”
(vpage 27).
NOTE
Specifications
Do not connect the UD9004’s video output via a VCR (Video Cassette Recorder). Some media contain
copy prohibit signals, which will disturb the screen image.
When playing NTSC disc, UD9004’s video output becomes NTSC signal format.
When playing PAL disc, UD9004’s video output becomes PAL signal format.
19
ENGLISH
Getting Started
3. Playing Back 2-Channel Audio
4. Recording a CD
Connecting to a Device with Analog 2-channel Audio Input
Terminal with Balanced Cable
Connecting to a Digital Recording Device
Connections
Select “Audio Setup” – “XLR” (vpage 30) from the GUI menu beforehand to match the device to be
connected.
MD Recorder
AUDIO
COAXIAL
IN
Stereo
Setup
AUDIO
AUDIO
IN
OPTICAL
IN
Playback HDMI Control Function Information
L
R
NOTE
•Do not short circuit between each terminals. When making connections, check the input terminal
layout of the device to be connected with the owner's manual.
•The default UD9004 balance model XLR input connectors pin alignment is as shown.
q GROUND w HOT e COLD
Troubleshooting
For software recorded in multi-channel, analog signals that have been down-mixed into 2 channels
are output.
Connecting to a Device with Analog 2-channel Audio Input
Terminal with Stereo Pin Plug Cable
Specifications
On the GUI menu, select “Audio Setup” – “7.1ch Audio Out”, and set it to “2 channel” (vpage 27).
Stereo
AUDIO
AUDIO
IN
L
L
L
R
R
R
For software recorded in multi-channel, analog signals that have been down-mixed into 2 channels
are output.
20
When converting multi-channel audio to 2-channel for output, on the GUI menu, select “Audio Setup”
– “Digital Out”, and set it to “PCM Down Sampling” (vpage 29). If you play back DVD or other media
with incorrect configuration, deafening noise occurs that may damage the speaker.
ENGLISH
System Requirement
Connecting to the Network
Internet
LAN port/
Ethernet
connector
To WAN port
Device that connects to the broadband circuit and conducts communications on the Internet.
A type that is integrated with a router is also available.
nn Router
When using the UD9004, we recommend a router with the following features.
•Built-in DHCP (Dynamic Host Configuration Protocol) server.
Function that automatically assigns an IP address on the LAN.
•Built-in 100BASE-TX switch (built-in switching hub compatible with speeds upwards of 100 Mbps)
nn Ethernet cable (CAT-5 or greater recommended)
•An Ethernet cable is not included with the UD9004.
•For Ethernet cable, we recommend you use shielded straight cable (normal type).
If you use the flat type or a non-shielded cable, the noise may adversely affect other devices.
To LAN port
To LAN port
For Internet connection, use an ISP (Internet Service Provider). Ask your local dealer for details.
NETWORK
connector
NOTE
nn Others
21
Specifications
•The UD9004 can use the DHCP function to automatically set the network.
•With the type of circuit in which network setting is performed manually, when subscribed to a provider,
conduct the setting in accordance with “Network Setup” on the GUI menu (vpage 31).
•If you connect the UD9004 to a network without a DHCP function, conduct IP address and other settings
according to “Network Setup” on the GUI menu (vpage 31).
•The UD9004 does not support PPPoE. If you subscribe to a circuit that is set with PPPoE, a PPPoEcompatible router is required.
•When setting manually, check the setting contents with the network administrator.
Troubleshooting
• It is necessary to subscribe to an ISP in order to connect to the Internet. If you already have a
broadband connection, there is no need to subscribe anew.
• The router you can use varies with the ISP. For more information, contact your ISP or PC dealer.
•M
ARANTZ assumes no responsibility whatsoever for any communication errors or troubles resulting
from customer's network environment or connected devices.
Playback HDMI Control Function Information
Modem
nn Modem
Setup
Computer
nn Internet Connection by Broadband Circuit
Connections
•You can update by downloading the latest firmware from the Internet.
For more information, on the GUI menu, select “Other Setup” – “Firmware Update” (vpage 33).
•See “Network Setup” (vpage 31) on the GUI menu for more information on network setting.
Router
Getting Started
5. Updating to the UD9004’s Latest Software Version
ENGLISH
Getting Started
Connecting the Power Cord
Once Connections are Completed
Connect the included power cord to the UD9004, and plug it into an AC outlet.
Connections
To household power
outlet (AC 120 V, 60 Hz)
Power cord
(included)
Turning the Power On
Press the unit’s POWER ON/STANDBY button or the
remote control’s POWER ON/OFF button.
“LOADING” appears on the display, and disc information is read.
bbThe “NO DISC” message is displayed when a disc is not loaded.
Setup
(UD9004)
(Remote control
unit)
Playback HDMI Control Function Information
NOTE
•Be sure to insert the power plug firmly. Incomplete connection results in noise generation.
On the GUI menu, when “Other Setup” – “Auto Power Mode” – “On” (vpage 32), the following states are
maintained for about 30 minutes, and then the power is turned automatically to standby.
•Disc not loaded
•Playback has stopped
•Stopped due to resume function
nn When power is switched to standby
Either press POWER ON/STANDBY button on the unit, or press POWER ON/OFF button on the remote
control.
The power indicator lights red.
NOTE
Troubleshooting
During power standby, a slight amount of power is consumed. To totally cut off the power, remove the
power cord from the power outlet.
Specifications
22
ENGLISH
Getting Started
GUI Menu Setup
Menu Map
Connections
Pressing SET UP button displays the GUI menu. From this menu, you can move to various setting screens.
Language Setup (vpage 25)
n Disc Menus
n GUI Language
Setup
n Dialog
n Subtitle
HDMI Setup (vpage 25, 26)
n Audio Setup
n SA-CD Audio Out
n HDMI Control
Playback HDMI Control Function Information
n Auto Format
n Color Space
n Deep Color
Video Setup (vpage 26)
n TV Aspect (Aspect ratio)
n Component Resolution
n Progressive Mode
n TV Active Area
Pure Direct Setup (vpage 30)
Audio Setup (vpage 27 ~ 30)
n 7.1ch Audio Out
• Multi Channel
• 2 Channel
n Subwoofer Mode
n Source Direct
n Compression
n
n
n
n
n
n
AFDM
BD Effect Sound
BD Re-Encoder
Digital Out
Downmix
XLR
n User Preset 1
n User Preset 2
Network Setup (vpage 31)
n IP Address
n MAC Address
Other Setup (vpage 32)
n
n
n
n
Auto Power Mode
Power Saving
Remote Control Setting
BD Data Utility
n Rating Country Code
n DivX Registration
Specifications
n DHCP
n Proxy
n Password
n BD Rating Level
n DVD Rating Level
Troubleshooting
Ratings (vpage 31)
Display Setup (vpage 32)
n Screen Saver
n Wallpaper
n Still Mode
n Slide Show Time
n Temporary Display
n Captions
n Initialize
n Firmware Update
n Information
23
ENGLISH
Getting Started
GUI Menu Operation
Connections
1 Press SET UP button.
Press d, f, 1 buttons to select the
2 menu
to be set or operated.
The GUI menu is displayed on the TV screen.
Examples of GUI Menu Screen Displays
Typical examples are described below.
GExample 1H Menu selection screen (Top menu)
GExample 2H Rating Country Code input screen (with
virtual keyboard)
b To return to the previous item, press 0 or
RETURN button.
Setup
3
Press ENTER button to enter the
setting.
z1
z2
Playback HDMI Control Function Information
n Exiting the GUI Menu
LANGUAGE SETUP
Dialog
Subtitle
Disc Menus
GUI Language
z3
Enter the country code.
Press SET UP button while the GUI menu is displayed.
• The GUI menu display disappears.
1 2
a b
n o
A B
N O
!
“
.
/
_ {
z5
NOTE
You must use the GUI menu to make settings or operate while a disc
or SD Memory Card is not inserted. In cases in which the resume
function is activated, you may not make correct settings.
■
z4
Set the language used for playback dialogs, subtitles, and
menus.
z1 : List GUI menu setup icons
z2 : Currently selected setup icon
z3 : Currently selected setup item
z4 : List of currently selected setup items
z5 : Guide text for the currently selected
setup item
Press f button to select “
Troubleshooting
” and then press 1
button.
(Or press ENTER button.)
3
c
p
C
P
#
:
|
4
d
q
D
Q
$
;
}
CURSOR
5
e
r
E
R
%
<
`
6
f
s
F
S
&
=
˜
Enter
7
g
t
G
T
’
>
←
8
h
u
H
U
(
?
→
0-9
9 0
i
j
v w
I
J
V W
)
*
@ [
Delete
0∼9
Space
k
l
x y
K L
X Y
+
,
¥
]
Finish
m
z
M
Z
−
^
RETURN
Return
z8
z9
z8 : Virtual keyboard
z9 : Operation button guide
n Icon
Switch the selected item
(Use d button to switch.)
Switch to the next item
Selected item
Specifications
Switch the selected item
AUDIO SETUP
z6
7.1ch Audio Out
Subwoofer Mode
Source Direct
Compression
AFDM
BD Effect Sound
Multi Channel
2 Channel
24
(Use f button to switch.)
n List
z7
Set to output analog 7.1ch audio.
Text colors of selected items of the GUI menu are as follows:
• White : These items can be selected.
• Gray : These items cannot be selected.
(Use 1 button to switch.)
z6 : Selected setup icon
z7 : Options of the selected setup item
Returns to the previous item
7.1ch Audio Out
Subwoofer Mode
Source Direct
Compression
AFDM
BD Effect Sound
(Use 0 or RETURN button to
switch.)
Switch to the next item
(Use 1 button to switch.)
Selected item
b Switch the selected item
using d, f buttons.
ENGLISH
HDMI Setup
Default settings are underlined.
Set the language used for playback dialogs, subtitles, and menus.
English/Français/Español/Deutsch/Italiano/Svenska/Nederlands/
NOTE
The setting may not be active depending on the disc.
Max Res. : Output data using the maximum resolution that can be
handled by the connected TV. When a TV is connected to both HDMI 1
and 2, maximum resolution corresponding with both is output.
Panel Res. : Output data using the maximum resolution of the panel of the
connected TV. When a TV is connected to both HDMI 1 and 2, resolution
corresponding with both and that of the larger panel is output.
Color Space
GHDMI 1H or GHDMI 2H : Set the video signal system to be output from
Set the video signal system HDMI1 or HDMI2.
to be output from HDMI.
• YCbCr : Output by YCbCr video format.
• RGB Normal : Output using the RGB video system (16 (black) to 235 (white)).
• RGB Enhanced : Output using the RGB video system (0 (black) to 255 (white)).
Deep Color
Expands the color depth
(number of used colors) of the
HDMI video signal, enabling
playback with more natural
colors and free of streaking.
GHDMI 1H or GHDMI 2H : Set the HDMI1 or HDMI2 terminal to output Deep
Color.
• Auto : Deep Color is automatically output when the connected HDMI
device supports Deep Color.
• Off : Do not output Deep Color.
To output sound from a disc while maintaining the same sound quality
as the disc sound, some settings of Audio Setup are disabled as default
(vpage 25 ~ 27).
To enable the settings of Audio Setup, set Source Direct to “Off”
(vpage 26).
GMulti LPCM BM OffH : Decoded Linear PCM multi-channel signal is
output by the UD9004. This setting is not made in speaker setting. (BM:
Bass Management)
G2chH : Output the downmixsed 2-channel LPCM signal.
GMuteH : Do not output audio from HDMI.
Remote control operation
buttons
SET UP
:Displaying the menu
Cancel the menu
Moves the cursor
d f 0 1 :
(Up/Down/Left/Right)
ENTER :Decision the setting
RETURN :Return to previous menu
25
Specifications
Audio Setup
GAutoH : Automatically selects and outputs signals that can be input to
Set the audio signal system the connected HDMI device. The bitstream signal takes priority.
to be output from HDMI.
GMulti LPCM BM OnH : Decoded Linear PCM multi-channel signal is output
by the UD9004. Speaker setting is enabled. (BM: Bass Management)
For setting, on the GUI menu, refer to, “Audio Setup” – “7.1ch Audio Out”
(vpage 27, 28).
• Speaker Configuration : Set the speaker configuration used for
playback. Automatically sets channel components and characteristics
according to setting.
• Channel Level : Set the volume of the test tone to be the same when it
is output from each speaker.
• Distance : Set the distance between the listening position and each
speaker.
Troubleshooting
If “Other” is selected for “Dialog”, “Subtitle” or “Disc Menus”, refer to “Language Code List” (vpage
51), use number buttons 0 ~ 9 button to input the language code, then press ENTER button to set.
Auto Format
Set the content of HDMI
video output resolution
item “Auto” (vpage 15)
with HDMI RESOLUTION
button.
Playback HDMI Control Function Information
English/French/Spanish/German/Japanese/Italian/Swedish/Dutch/
Disc Menus
Set the language used for Russian/Chinese/Korean/Danish/Finnish/Norwegian/Icelandic/
Hungarian/Romanian/Turkish/Greek/Irish/Portuguese/Polish/Czech/
BD or DVD menus.
Slovak/Bulgarian
Others : Enter the language code.
Setting contents
Setup
Off : Do not display subtitles.
Subtitle
Set the subtitle language English/French/Spanish/German/Japanese/Italian/Swedish/Dutch/
Russian/Chinese/Korean/Danish/Finnish/Norwegian/Icelandic/
used to play BDs or DVDs.
Hungarian/Romanian/Turkish/Greek/Irish/Portuguese/Polish/Czech/
Slovak/Bulgarian
Others : Enter the language code.
Setting items
Connections
Dialog
Original : Plays the dialog selected at the top in the language menu
Set the dialog used to play stored in the disc.
BDs or DVDs.
English/French/Spanish/German/Japanese/Italian/Swedish/Dutch/
Russian/Chinese/Korean/Danish/Finnish/Norwegian/Icelandic/
Hungarian/Romanian/Turkish/Greek/Irish/Portuguese/Polish/Czech/
Slovak/Bulgarian
Others : Enter the language code.
GUI Language
Set the GUI language.
Default settings are underlined.
Set the HDMI output signal or HDMI control function.
Setting contents
Setting items
Getting Started
Language Setup
ENGLISH
Getting Started
HDMI Setup
Setting contents
Setting items
Connections
SA-CD Audio Out
On : Super Audio CD audio is output.
Set to output stereo/multi Off : Super Audio CD audio is not output.
area audio of Super Audio
CD to the HDMI terminal.
The Super Audio CD audio signal is a 44.1 kHz/16-bit Linear PCM output.
Setup
HDMI Control
Can operate the unit in
conjunction with an HDMI
control support device.
Video Setup
GControlH
• Off : Disable the HDMI control function.
• HDMI1 On : Link with the device connected to HDMI1.
• HDMI2 On : Link with the device connected to HDMI2.
Playback HDMI Control Function Information
GPower Off ControlH
• On : Turns the UD9004’s power to standby through linkage to the TV.
• Off : Does not turn the UD9004's power to standby through linkage to
the TV.
• For the HDMI control function to operate, it is necessary for the UD9004
or HDMI-compatible TV connected to the UD9004 to have an HDMI
connection.
• Refer to “HDMI Control Function” (vpage 49) for more information
about the HDMI control function.
• After the “HDMI Control” setting has been changed, always turn off the
power to the connected equipment and then turn it back on.
Default settings are underlined.
Set the video output signal according to the connected TV.
Setting contents
Setting items
TV Aspect (Aspect ratio)
16:9 Squeeze Auto : Output to a wide screen TV. For 4:3 video, display in
Set the screen type and the center of the screen without changing the aspect ratio.
display mode of the TV.
WIDE (16:9) : Output to a wide screen TV.
4:3 PS : Output to a 4:3 TV. For wide video, trim the left and right side of
the image and display in 4:3 aspect ratio. z1
4:3 LB : Output to a 4:3 TV. Display all of the wide video. z2
480/576i, 480/576P, 720P, 1080i,
Component Resolution
Set the component output Source Direct : Output video using its source resolution. Convert the
1080p video source to 1080i.
resolution.
Progressive Mode
Set an appropriate progressive
conversion mode for the
source video material.
Auto : Detect the type of video material and automatically switch the
mode. Normally, this setting is used.
Video1 : Suitable for playing video material discs.
Video2 : Suitable for playing video material discs or 30-frame film material
discs.
Full : Set when a home-use monitor is connected.
TV Active Area
Sets the horizontal display Normal : This setting is used when video synchronization is disturbed on
range when the analog a professional-use monitor.
video output resolution is
This is not available for HDMI output.
480i/576i.
z1 : Depending on the video content, even though you set the 4:3 PS (Pan Scan), the content may be
output in 4:3 LB (Letter Box).
z2 : Only valid for content recorded in 480i/576i.
Troubleshooting
Specifications
26
Remote control operation
buttons
SET UP
:Displaying the menu
Cancel the menu
Moves the cursor
d f 0 1 :
(Up/Down/Left/Right)
ENTER :Decision the setting
RETURN :Return to previous menu
ENGLISH
Default settings are underlined.
Set the speaker or audio to be output.
Setting related to each channel setting and other audio in the case of outputting analog
audio signals decoded by the UD9004.
Multi Channel
Set the speaker configuration, channel level and distance for multichannel playback.
NOTE
When outputting multi-channel audio set to surround sound by the
UD9004, to the analog input of an AV Amp, set so that the AV Amp
outputs audio without modification. If the AV Amp conducts further
surround processing, the appropriate audio will not be output.
2 Channel
NOTE
Troubleshooting
Outputs multi-channel downmixed audio from the front speaker output
• You cannot select “None” terminals (FL/FR) of the 7.1-channel audio output terminals. Make this
or “No” for “HDMI Setup” setting when outputting to a TV and 2-channel amplifier.
– Audio Setup” – “Multi
NOTE
LPCM BM On” – “Speaker
Configuration” (vpage The 7.1-channel audio output terminals output only FL/FR when you
make this setting.
25) on the GUI menu.
• To output sound from a n Speaker Configuration : Set the speaker configuration.
disc while maintaining the
GFrontH : Set the front speaker size.
same sound quality as the
• Large : Use of a large speaker that can adequately play back low
disc sound, some settings
frequencies.
of Audio Setup are disabled
• Small : Use of a small speaker that has inadequate playback capacity
as default (vpage 25 ~
for low frequencies.
27).
To enable the settings of
GCenterH : Set the presence and size of the center speaker.
Audio Setup, set Source
• Large : Use of a large speaker that can adequately play back low
Direct to “Off” (vpage
frequencies.
26).
• Small : Use of a small speaker that has inadequate playback capacity
GSurr. BackH : Set the presence, size and number of surround back
speakers.
• Size : Set the surround back speaker size.
Large : Use of a large speaker that can adequately play back low
frequencies.
Small : Use of a small speaker that has inadequate playback capacity
for low frequencies.
None : Select when the surround back speakers are not connected.
• Number : Set the number of surround back speakers.
1 spkr : Use only one surround back speaker. Surround back audio is
output from the surround back L terminal.
2 spkrs : Use two surround back speakers.
Specifications
for low frequencies.
• None : Select when a center speaker is not connected.
GSubwooferH : Set the presence of a subwoofer.
• Yes : Use a subwoofer.
• No : Select when a subwooofer is not connected.
Remote control operation
buttons
SET UP
:Displaying the menu
Cancel the menu
Moves the cursor
d f 0 1 :
(Up/Down/Left/Right)
Playback HDMI Control Function Information
7.1ch Audio Out
Makes the audio setting for
output of analog 7.1-channel
audio to a multi-channel
amplifier.
To set “7.1ch Audio Out”,
set “HDMI Setup” – “Audio
Setup” on the GUI menu to
“2ch” or “Mute” (vpage
25).
Setup
Setting contents
GSurroundH : Set the presence and size of the Surround speakers.
• Large : Use of a large speaker that can adequately play back low
frequencies.
• Small : Use of a small speaker that has inadequate playback capacity
for low frequencies.
• None : Select when the surround speakers are not connected.
Connections
Setting items
Setting contents
Setting items
7.1ch Audio Out
Getting Started
Audio Setup
ENTER :Decision the setting
RETURN :Return to previous menu
27
ENGLISH
Getting Started
Audio Setup
Setting contents
Setting items
7.1ch Audio Out
Connections
Setup
Playback HDMI Control Function Information
GCrossover Freq.H : Set the upper limit of the low frequency signals
output from the subwoofer.
•40Hz/60Hz/80Hz/90Hz/100Hz/110Hz/120Hz/150Hz/200Hz/250Hz
: Outputs at below set frequency, each speaker’s bass signal
output from the subwoofer. Set this according to the low frequency
reproduction capabilities of the speakers you are using.
•Advanced : Set the low frequency signals to be output from the
signals of the respective speakers to the subwoofer.
Front, Center, Surround, Surr. Back
40Hz/60Hz/80Hz/90Hz/100Hz/110Hz/120Hz/150Hz/200Hz/250Hz
LFE / LFE+Main
80Hz/90Hz/100Hz/110Hz/120Hz/150Hz/200Hz/250Hz
Setting items
7.1ch Audio Out
Setting contents
n Channel Level : Set the volume of the test tone to be the same when
it is output from each speaker.
GModeH : Select a test tone output method.
•Auto : Automatically switch the test tone output speaker.
•Manual : Manually switch the test tone output speaker.
GStartH : Begin outputting the test tone.
Front L / Center / Front R / Surround R /
Surr. Back R / Surr. Back L / Surround L / Subwoofer
bbWhen the test tone output stops, press RETURN button.
GSW +10dBH : Increase the subwoofer output level by 10 dB. z
•Off : Do not change the subwoofer output level.
•On : Increase the subwoofer output level by +10 dB.
When, on the GUI menu, “Audio Setup” – “7.1ch Audio Out”– “Multi
Channel” – “Speaker Configuration” – “Subwoofer” is set to “Yes”
(vpage 27), you can select “LFE” or “LFE+Main”.
GDefaultH : Reset all channel level settings to factory default.
•No : Do not Reset.
•Yes : Reset.
NOTE
n Distance : Set the distance between the listening position and each
speaker.
Troubleshooting
•Select “Large” or “Small” not according to the physical size of the
speaker but according to the low frequency reproduction capabilities
based on the frequency set at “Crossover Freq.”.
•On the GUI menu, if the “Audio Setup” – “7.1ch Audio Out”– “Multi
Channel” – “Speaker Configuration” item setting is changed, other
settings are automatically changed as well.
GExampleH
If you set “Front” to “Small”, “Subwoofer” is set to “Yes” and “Large”
cannot be selected for “Center”, “Surround” and “Surr. Back”.
•Audio signal (sampling frequency, number of channels) from the
HDMI output terminal may be restricted by the specification of the
HDMI audio that can be input by the device at the other side.
GExampleH
If the HDMI audio specification of the device at the other side is the
5.1 channel, even when UD9004 plays back by the 7.1 channel, the
5.1 channel audio is automatically output. In that case, the analog
audio output becomes the 5.1 channel output as well.
GFeetH or GMetersH : Set the unit of distance.
GStepH : Set the minimum variable width of the distance.
1ft, 0.1ft, 0.1m, 0.01m
GDefaultH : Reset all distance settings to factory default.
Front L / Front R / Center / Subwoofer / Surround L / Surround R /
Surr. Back L / Surr. Back R : Select the speaker you want to set,
and set the distance. Set the value that is closest to the measured
distance.
0~60ft or 0~18m
Specifications
•Default settings :
Front/Center/Subwoofer : 3.6 meters (12 feet)
Surround/Surr. Back : 3.0 meters (10 feet)
•Set the difference in the distance betweem the speakers to less than
6.0 meters (20 feet).
Subwoofer Mode
Set the type of low frequency
signal to be output from the
subwoofer.
LFE : Add the low frequency signal of the channel for which the speaker
size is set to “small” to the subwoofer signal and output it.
LFE+Main : Add the low frequency signal of all channels to the subwoofer
signal and output it.
z : “SW +10dB” cannot be set for “HDMI Setup” – “Audio Setup” – “Multi LPCM BM On” – “Channel
Level” on the GUI menu.
28
Remote control operation
buttons
SET UP
:Displaying the menu
Cancel the menu
Moves the cursor
d f 0 1 :
(Up/Down/Left/Right)
ENTER :Decision the setting
RETURN :Return to previous menu
ENGLISH
Setting contents
Off : Enable the speaker and subwoofer settings.
On : 50kHz : Output the disc contents as is. When playing Super Audio
CD, output up to 50 kHz audio signals.
On : 100kHz : Output the disc contents as is. When playing Super Audio
CD, output up to 100 kHz audio signals with DSD format.
NOTE
Setting contents
Setting items
AFDM
Automatically
set
the
surround mode by detecting
the
surround
mode
identification signal recorded
in the disc.
On : Automatically set surround mode when the ID signal is included.
Off : Do not set surround mode even when the ID signal is included.
MTRX : Create a surround audio signal by matrix processing, regardless
of the presence of an ID signal.
Valid when “BD Audio Mode” is set to “Mix Audio Output” (vpage
33).
Digital Out
Set the audio signal of digital
audio output.
For more information on each
audio signal, refer to “Audio
Signal from the Digital Audio
Output
(Optical/Coaxial)
Terminal” (vpage 17).
Bitstream : Outputs a bitstream signal. Converts Dolby TrueHD, Dolby
Digital Plus to Dolby Digital, and DTS-HD to DTS for output.
PCM : Output the downmixed audio signal to 2ch LPCM.
PCM Down Sampling : Convert sampling frequency audio greater than
48 kHz to a 48 kHz 2ch LPCM audio output signal.
Downmix
Set the method used to
convert a multi-channel
audio signal to a 2-channel
signal.
Lt/Rt : Signals are converted to Dolby Surround compatible 2-channel
audio signals for output. This setting is valid for DTS-HD, DTS Digital
Surround, Dolby Digital Plus and Dolby Digital audio signals. (If the
connected AV Amp is Dolby Pro Logic compatible, AV Amp plays back
using surround audio.)
Stereo : Outputs by converting to the 2ch (stereo) audio.
NOTE
NOTE
In order to enable the “Lt/Rt” setting when playing back BD, set “BD
Audio Mode” to “HD Audio Output” (vpage 33).
•This setting is valid when “Audio Setup” – “7.1ch Audio Out” on the GUI
menu is set to “Multi Channel” (vpage 27) and when “HDMI Setup” –
“Audio Setup” on the GUI menu is set to “Multi LPCM BM On” (vpage
25).
•This setting is invalid when “Audio Setup” – “Source Direct” on the GUI
menu is set to “On” (vpage 29).
•This function is invalid for the DTS-CD source.
Remote control operation
buttons
SET UP
:Displaying the menu
Cancel the menu
Moves the cursor
d f 0 1 :
(Up/Down/Left/Right)
ENTER :Decision the setting
RETURN :Return to previous menu
29
Specifications
An EX flag may not be included for Dolby Digital EX sources. Even with
“AFDM” set to “On”, set to “MTRX” in case the playback mode does not
automatically switch.
•When outputting CD, etc. to a digital recording device such as the CD
recorder, convert to PCM or PCM down sampling.
•When a disc with recorded Linear PCM or PPCM (Packed PCM) is played
back, this outputs Linear PCM irrespective of the setting.
Troubleshooting
Auto : Automatically compress Dolby TrueHD audio dynamic range. The
sound is not compressed when playing signals other than Dolby TrueHD
signals.
Off : Dynamic Range compression is not applied.
Low : Set minimum dynamic range compression.
Middle : Set middle dynamic range compression.
High : Set maximum dynamic range compression.
Auto : Outputs primary audio (main audio) in the same type of audio
format. Dolby Digital/Dolby Digital Plus/Dolby TrueHD are output as
Dolby Digital, DTS/DTS-HD are output as DTS and Linear PCM is output
as Linear PCM.
Dolby Digital : Outputs to the digital audio output terminal (optical/
coaxial) with Dolby Digital.
DTS : Outputs to the digital audio output terminal (optical/coaxial) with
DTS.
Playback HDMI Control Function Information
Compression
Compresses the dynamic
range of Dolby TrueHD/
Dolby Digital/Dolby Digital
Plus audio. At night or other
times when you cannot play
back at high volume, this
compensates by reducing
high level sounds and
increasing low level sounds.
BD Re-Encoder
Sets the format during
output of the BD’s Mix Audio
signal from the digital output
terminal.
Setup
Set to within the playback
frequency band of the •Setting “On: 50 kHz” or “On: 100 kHz” enables full-range playback on
amplifier you are to use: all channels recommended for DTS. (Note that this results in a 5 dB
“On” at “50 kHz” or “100 increase in subwoofer volume, and a 15 dB increase with Super Audio
kHz”. Setting outside the CD). This also allows you to play back the 6-channel source of DVDfrequency band can result Audio recorded on all channels with the full frequency range. In this
in damage to your amplifier case, make an analog connection according to disc operating manual.
•When set to “On: 50 kHz” or “On: 100 kHz”, all speaker sizes are set to
and even fire.
“Large” and “Yes” is set for the subwoofer.
•Even when set to “On: 50 kHz” or “On: 100 kHz”, “Channel Level” and
“Distance” settings are available.
BD Effect Sound
On : Outputs BD effect sound.
Sets for a click sound and Off : Does not output BD effect sound.
other outputs during BD
popup menu operations.
Connections
Setting items
Source Direct
Disable the speaker and
subwoofer settings and
output the disc audio as is.
Getting Started
Audio Setup
ENGLISH
Getting Started
Audio Setup
Pure Direct Setup
Setting contents
Setting items
Makes settings regarding digital audio and video output modes during Pure Direct mode,
as well as display messages. Two types of setting can be registered.
Connections
XLR
GTerminal PolarityH : Set the polarity of the XLR terminal.
Set the signal to be output • Normal : Normal polarity.
from the XLR terminal.
• Inversion : Reverse the polarity.
Setup
GGain UpH : Can increase output gain when the input sensitivity of a
device connected via XLR is low.
• Off : Outputs at standard gain from the XLR terminal.
• On : Increase the output gain of the XLR terminal. Set when the input
sensitity of the connected device is low.
Playback HDMI Control Function Information
The default UD9004 balance model XLR audio connectors pin alignment
is as shown.
q GROUND w HOT e COLD
Default settings are underlined.
Setting items
Setting contents
User Preset 1/
User Preset 2
This sets the operating
mode for “User Preset 1” or
“User Preset 2” selected by
PURE DIRECT button.
Setting each of these items
to “Off” enables output of
high quality analog signals
free of interference from the
associated circuits.
GDigital OutH : Set whether to output signals to the digital audio output
terminal.
• On : Enable digital audio output.
• Off : Disable digital audio output.
GVideo OutH : Set option of video output.
• On : Enable video output.
• Off : Disable video output. This setting also disables audio output from
the HDMI terminal.
GDisplayH : Set option for front panel display.
• On : Turn on display.
• Off : Turn off display.
For more information, see “Playing Back High-quality Audio (Pure Direct
Function)” (vpage 40).
Troubleshooting
Specifications
30
Remote control operation
buttons
SET UP
:Displaying the menu
Cancel the menu
Moves the cursor
d f 0 1 :
(Up/Down/Left/Right)
ENTER :Decision the setting
RETURN :Return to previous menu
ENGLISH
Network Setup
Default settings are underlined.
Set BD or DVD parental lock or display DivX® registration codes.
SET UP
:Displaying the menu
Cancel the menu
Proxy
GOffH Do not use a proxy server.
Set to connect to the Internet GOn (Address)H Set to connect to the Internet via a proxy server. Use the
via a proxy server.
address to specify the proxy server. Use 0 ~ 9 button to enter the address
and then press ENTER button to finalize it.
• Port : Use 0 ~ 9 button to enter a port number and then press ENTER
button to finalize it.
GOn (Name)H Set to connect to the Internet via a proxy server. Specify the
proxy server using the domain name. Input the domain name with the
virtual keyboard, using d, f, 0, 1 and ENTER buttons.
• Port : Use 0 ~ 9 button to enter a port number and then press ENTER
button to finalize it.
IP Address
UD9004’s IP address is displayed. If the IP address cannot be obtained or
is not set, “···” is displayed. In that case, check that the connection and
network configuration is correct.
MAC Address
Displays the MAC address of the UD9004.
Moves the cursor
d f 0 1 :
(Up/Down/Left/Right)
ENTER :Decision the setting
RETURN :Return to previous menu
31
Specifications
Remote control operation
buttons
Since the factory default
setting is “On”, you do not
need to set items such as
the IP address if the DHCP
server of the broadband
router is set to “Enable”.
Configure a proxy server if
necessary.
Troubleshooting
DivX Registration
Display the DivX® registration
code.
Argentina / Australia / Austria / Belgium / Brazil / Canada / Chile /
China/ Denmark / Finland / France / Germany / Hong Kong / India
/ Indonesia / Italy / Japan / Korea, Republic of / Malaysia / Mexico
/ Netherlands /New Zealand / Norway / Pakistan / Philippines /
Portugal / Russian Federation / Singapore / Spain / Switzerland
/ Sweden / Taiwan / Thailand / United Kingdom / United States /
Colombia / Greece / Ireland / Luxembourg / Poland
Others : Inputs the country code. Refer to “Country Code List” (vpage
52) and, with the virtual keyboard, use d, f, 0, 1 and ENTER buttons to
input the country code.
Show Code : Display the DivX® registration code
GOnH : Automatically configure the network by the DHCP function.
GOffH : When connecting to a network, which does not have the DHCP
function, manually configure the following network settings. For the
details of the settings, confirm with the provider or network administrator.
Use 0 ~ 9 button to enter a value and then press ENTER button to finalize
it.
• IP Address : Manually set the IP address of the UD9004.
• Subnet Mask : If the xDSL modem or terminal adaptor is directly
connected to the UD9004, enter the subnet mask notified by the
provider usually in a document. Usually, “255.255.255.0” is set.
• Default Gateway : If the device is connected to a gateway (router),
enter its IP address.
• Primary DNS : Enter the primary DNS.
• Secondary DNS : Enter the secondary DNS.
Playback HDMI Control Function Information
Level1 ~ 8 : Set the parental level for playing DVD.
DVD Rating Level
Set the parental level for Lock All : Restrict playing of all DVDs.
No Limit : Do not restrict playing of DVDs.
playing DVD.
Setting contents
Setup
Level 0 ~ 254 : Set the age allowed to play back media. Restricts playback
BD Rating Level
Set the parental level for of discs with relevant parental control.
No Limit : Do not restrict playing of BDs.
playing BD.
Setting items
DHCP
Set how to perform network
configuration, automatically
or manually.
Connections
Password
Change : Change the password.Use 0 ~ 9 button to enter a password
Sets the password for changing and then press ENTER button to finalize it.
the parental control level and The default setting is “0000”.
parental control country code
of BD and DVD.
Rating Country Code
Sets the standard country
parental control.
Apply the parental level of
the set country.
Set to connect to the Internet.
To obtain update support for your UD9004, you can download the latest firmware from
our website.
Make a network connect beforehand according to “Connecting to the Network” (vpage
21).
Setting contents
Setting items
Default settings are underlined.
Getting Started
Ratings
ENGLISH
Getting Started
Display Setup
Other Setup
Default settings are underlined.
Set display-related items.
Set other items.
Setting contents
Setting items
Connections
Screen Saver
Set the screensaver.
Default settings are underlined.
Setting contents
Setting items
Off : Do not use the screensaver.
On : The screensaver function activates when stop or pause status
continues for about three minutes.
Setup
Picture : Displays the MARANTZ logo.
Wallpaper
Set to display the background Black : Set the background to black.
while playback is stopping. Gray : Set the background to gray.
Blue : Set the background to blue.
Playback HDMI Control Function Information
Automatic : Display automatically using “Field” or “Frame” per the still
Still Mode
Set image quality during image information.
Field : Set when there is a blurred image when “Automatic” image display
pause.
is set.
Frame : Set to display non moving images in high resolution.
3 ~ 5 ~ 100sec : This sets the display time per frame of a JPEG file during
Slide Show Time
Sets the display time of slideshow playback.
JPEG files.
Off : Do not temporarily display operations.
Temporary Display
When the display is set to On : Temporarily display operations.
“Off” by the Dimmer Control
(vpage 49) or Pure Direct
Function (vpage 40), this
sets it to temporarily display
operations received.
Troubleshooting
Off : Do not output the closed caption (subtitle) signal.
Captions
This setting output a subtitles On : Output the closed caption (subtitle) signal.
signal to a closed caption
decoder (sold separately).
Auto Power Mode
Off : Do not use auto power mode.
This setting automatically On : This setting automatically sets the power to standby if any of the
sets the power to standby. following states continues for approximately 30 minutes.
• Disc not loaded
• Playback has stopped
• Stopped due to resume function
Power Saving Standby : This is the lowest power consumption mode.
Power Saving
Set power saving mode During standby, operations are not accepted via HDMI control or RS232C.
during standby.
Normal Standby : This is the low power consumption mode. During
standby, operations are accepted via RS-232C but not accepted by HDMI
control.
HDMI Control Mode : Setting for turning the power on using an external
device’s HDMI control function or by operation via RS-232C. Slightly
higher power consumption.
Quick Start Mode : Start up time is faster but power consumption during
standby is higher.
Remote Control Setting GRemote IDH
(Main unit side)
Switches the UD9004’s remote control ID code when other MARANTZ
Set the remote control.
BD Players are in the vicinity.
• BD 1 : Set the code setting on the remote control to “1” (vpage 7
“Remote Control Setting (Remote Control Side)”).
• BD 2 : Set the code setting on the remote control to “2” (vpage 7
“Remote Control Setting (Remote Control Side)”).
BD Data Utility
BD Data Erase : Erases both internal memory and SD Memory Card
Erases data on SD Memory storage.
Card, and initializes cards.
Initialize SD Card : Initialize the SD card to be used for the Bonus View
function.
NOTE
Specifications
• Insert or remove a SD Memory Card while the power is in standby.
If you insert a SD Memory Card while the power is ON, the SD Memory
Card may not be read.
• The SD card used for the Bonus View function must have a capacity of
1GB or greater. Also the SD card must be initialized on the UD9004.
• This operation will delete all the data. Do not perform this operation
when an SD card containing MP3 or JPEG data is inserted.
32
Remote control operation
buttons
SET UP
:Displaying the menu
Cancel the menu
Moves the cursor
d f 0 1 :
(Up/Down/Left/Right)
ENTER :Decision the setting
RETURN :Return to previous menu
ENGLISH
Setting contents
Setting items
Various Settings
You can set the audio mode and change playback files.
You can set various modes during playback. The setting menu is displayed at the top of the screen.
Cautions on “Firmware Update”
Off
Mix Audio Output
All
bbThe display content changes depending on the media being played back.
the setting item using d, f buttons, and then press ENTER
2 Select
or 1 button.
d, f buttons to select a setting and use ENTER button to change
3 Use
the setting.
Setting the Audio Mode
Default settings are underlined.
Setting contents
Setting items
BD Audio Mode
HD Audio Output : Can view by outputting high quality signals such as
Switch BD audio playback Dolby TrueHD, Dolby Digital Plus, or DTS-HD as its high sound quality
mode.
bitstream. Cannot listen to interactive or secondary audio.
Mix Audio Output : Outputs a mix of primary audio/interactive audio/
secondary audio.
In the case of Dolby TrueHD, Dolby Digital Plus and DTS-HD audio
playback, set to “HD Audio Output”.
NOTE
When “Mix Audio Output” is set and DTS-HD audio signals are played,
only the DTS digital surround stream of the DTS-HD audio stream is
decoded and output.
Direct : Do not apply surround processing and output audio as is.
DOLBY PLgx (or PLg) : Apply DOLBY PLgx (or PLg) surround processing
and output the signal.
DTS NEO:6 : Apply DTS NEO:6 surround processing and output the
signal.
NOTE
•This setting is valid when “Audio Setup” – “7.1ch Audio Out” on the GUI
menu is set to “Multi Channel” and when “HDMI Setup” – “Audio Setup”
on the GUI menu is set to “Multi LPCM BM On” (vpage 25).
•This setting is invalid when “Audio Setup” – “Source Direct” on the GUI
menu is set to “On” (vpage 29).
Remote control operation
buttons
SET UP
:Displaying the menu
Cancel the menu
Moves the cursor
d f 0 1 :
(Up/Down/Left/Right)
ENTER :Decision the setting
RETURN :Return to previous menu
33
Specifications
Surround Mode
Converts a 2-channel source,
etc. to output multi-channel
surround audio.
Troubleshooting
•In order to use these functions, you must have the correct system requirements and settings for a
broadband Internet connection (vpage 21, 31).
•Do not turn off the power until updating is completed.
•Information regarding the “Firmware Update” function will be announced on the MARANTZ web site
each time related plans are defined.
•Even with a broadband connection to the Internet, approximately 1 hour is required for the updating
procedure to be completed.
Once updating starts, normal operations on the UD9004 cannot be performed until updating is
completed. Also, setting items of the GUI menu of UD9004 or setting items of the image adjustment
may be initialized.
Vertical Stretch
BD Audio Mode
File filter
Playback HDMI Control Function Information
Information
GFont LicenseH
Displays the license for Japanese (Original) : Displays in Japanese.
the IPA font used by this The font used in this product’s GUI menu screen conforms to IPA
product.
font specifications. See the following URL for the IPA font license
agreement.
http://ipafont.ipa.go.jp/enduser_license.html
Displays the currently settable menu.
Setup
Firmware Update
Check for Update : Check if the latest firmware exists. You can also
Update the firmware of the check approximately how long it will take to complete an update.
unit via the Internet.
Start : Starts firmware update.
When updating starts, the power indicator lights red and the GUI screen
is shut down.
During update, a rough remaining time is indicated on the display.
When updating is complete the power indicator lights green and normal
status is resumed.
1 Press MODE button.
Connections
Initialize
Cancel : Do not initialize.
All settings including audio OK : Execute initialization.
mode and picture quality are
default settings.
Getting Started
Other Setup
ENGLISH
Getting Started
Setting the Audio Mode
Connections
Setting contents
GPLgx ModeH : Sets to Dolby Pro Logic gx mode.
GPLg ModeH : Sets to Dolby Pro Logic g mode.
•Cinema : Appropriate setting for movie sources.
•Music : Appropriate setting for music sources.
Dimension (Setting value : 0 ~ 3 ~ 6) : Shift the center of the acoustic
field forwards or backwards to adjust the playback balance.
Center Width (Setting value : 0 ~ 3 ~ 7) : Shift the center channel audio
left or right to widen the forward acoustic field image.
Panorama (Setting : Off/On) : Expand the acoustic field of the front left
and right channel to the surround channel to widen the forward acaustic
field image.
•Game : Appropriate mode for gaming.
•Pro Logic : Pro Logic playback mode.
GDTS NEO:6 ModeH : Sets to DTS NEO: 6 mode.
•Cinema : Appropriate setting for movie sources.
•Music : Appropriate setting for music sources.
Center Image (Setting value : 0 ~ 0.3 ~ 1.0) : Shift the center channel
audio left or right to widen the forward acoustic field image.
Setup
Setting items
Surround Parameters
Sets the parameters of
surround mode.
The parameters which can
be adjusted vary with each
surround mode.
Playback HDMI Control Function Information
Restorer
Compensates
for
the
heaviness of bass and
treble in compressed audio
sources, to produce a sound
that is closer to the state
before compression.
Off : The “Restorer” is not used.
Mode1 (Restorer64) : Corrects the treble for compressed audio sources
with extreme lack of treble.
Mode2 (Restorer96) : Optimally corrects treble and bass for compressed
audio sources.
Mode3 (RestorerHQ) : Corrects the bass for compressed audio sources
with sufficient treble.
NOTE
Troubleshooting
•Effective for compressed audio source of MP3, WMA, AAC, Dolby
Digital, DTS, and MPEG.
•This setting is invalid when “Audio Setup” – “Source Direct” on the GUI
menu is set to “On” (vpage 29).
Specifications
34
Changing the Playback File Display
Default settings are
underlined.
Setting items
Setting contents
File filter
All : Plays back MP3/WMA/AAC/LPCM/JPEG/DivX® files.
Selects the file format you Audio : Plays back MP3/WMA/AAC/LPCM files.
want to play back from Picture : Plays back JPEG files.
among the files mixed on a Video : Plays back DivX® files.
disc.
Audio & Picture : Plays back MP3/WMA/AAC/LPCM/JPEG files.
This operation is effective only when playback is stopped.
Making Other Settings
Setting items
Secondary Video (PIP)
Default settings are underlined.
Setting contents
Off : Does not display Secondary Video(Picture-In-picture).
1/Xz : Displays the first Secondary Video.
2/Xz : Displays the second Secondary Video.
X/Xz : Displays the X th Secondary Video.
z : “ X” is the number of Secondary Videos recorded and differs
depending on the disc (“Playing Bonus View” vpage 38)
HDMI : Synchronizes audio output to HDMI output video.
Audio/Video Sync
Correct displaced video- Analog Video Out : Synchronizes audio output to analog video output.
audio playback timing.
0 ~ 200msec : Use this to adjust the audio output delay time manually.
Audio Delay Adjust
While
viewing
video,
manually adjust the time to
delay audio output.
Vertical Stretch
Extends
cinemascope
size video in the vertical
direction.
Off : Displays the source video signal without modification. This should
normally be set to “Off”.
On : Set when viewing cinemascope size video with a combination of
projector and anamorphic lens. Extends the image in the vertical direction
so that the top and bottom black portions disappear.
ENGLISH
You can adjust the picture quality to your liking.
You can store up to a maximum of 5 values in memory.
The currently set status is displayed.
PICT
the item you want to change
3 Select
with d, f buttons.
Memory 1
4
V.Position
DNR
Contrast
0
0
0
Change the setting with 0, 1 buttons.
bbRefer to the table on the right regarding contents of items which
can be set.
nn When Finishing Picture Adjustment
nn When Outputting Standard Picture
Quality without Using Picture
Adjustment
The picture adjustment set values are retained in
memory even after the power is turned off.
0
Contrast
Adjust picture contrast.
–6 ~ +6
0
PICT
Brightness
Adjust picture brightness.
0 ~ +12
0
Enhancer
Strengthens the contours of
the picture.
0 ~ +11
0
G0 ~ 9
G0 = 24 / G1 = 32
G2 = 48 / G3 = 64
G4 = 80 / G5 = 96
G6 = 128 / G7 = 160
G8 = 192 / G9 = 224
Gamma Correction
Adjust video brightness in
detail.
Sharpness (medium range)
z1
Adjust picture sharpness
for the medium frequency
range.
–6 ~ +6
Sharpness (high range)
Adjust picture sharpness for
the higher frequency range.
–6 ~ +6
0
Hue (color tone)
Adjust the green and red
color balance.
–6 ~ +6
0
White Level
Adjust the white level.
–5 ~ +5
0
Black Level
Adjust the black level.
–5 ~ +5
0
–6 ~ +6
0
0 IRE
7.5 IRE
7.5 IRE
H.Position
Adjust the left/right position.
–7 ~ +7
0
V.Position
Adjust
the
position.
–7 ~ +7
0
Chroma Level
Adjust the color density.
Setup Levelz2
Adjust the black areas of the
image.
top/bottom
In the example of the graph below, the horizontal axis shows the
brightness level of the pictured recorded on the disc. The vertical axis
shows the brightness of the picture output by the UD9004.
0
Memory 5
Gamma Correction
G0:024
255
0
0
255
•On adjusting the brightness on the output side of bright parts on
the disc side, the normally hard to see bright parts become clearly
discernible images.
PICT
Memory 5
255
0
0
Gamma Correction
G0:024
255
•On adjusting the brightness on the output side of dark parts on
the disc side, the normally hard to see dark parts become clearly
discernible images.
nn Resuming Initial Values after Gamma Correction
Press CLEAR button while a graph is displayed.
z1 : This is not available for HDMI output.
z2 : Effective only for the 480i video signal from the video output terminal, S
video output terminal, and component video output terminal.
35
Specifications
Press RETURN and d, f buttons to select
“Standard” and then press ENTER button.
0 ~ +3
When you select “Gamma Correction”, and then press ENTER
button, you can change the setting with d, f, 0, 1 buttons.
Troubleshooting
Press PICT. ADJUST button during picture
adjustment.
DNR
Reduce noise in the entire
picture.
About Gamma Correction
Playback HDMI Control Function Information
Memory 5
Standard
Memory 1
Default
Setup
ENTER button.
Setting
contents
Connections
1
the memory number you want (“Memory 1”
2 Select
~ “Memory 5”) with d, f buttons, and then press
Press PICT. ADJUST button.
Setting items
Getting Started
Adjusting the Picture Quality (Picture Control)
ENGLISH
Getting Started
Playback
Disc playback
Connections
Setup
n
n
n
n
n
Playing BD and DVD-Video (vpage 37, 38)
Playing Back Super Audio CD (vpage 39)
CD Playback (vpage 39)
DVD-Audio Playback (vpage 39, 40)
Playing Back High-Quality Audio (vpage 40)
Playback HDMI Control Function Information
File playback
n File Playback (vpage 40 ~ 42)
Operations Enabled During Playback
(vpage 43)
NOTE
Troubleshooting
• The “ ” (prohibited mark) may appear on the top right of the TV
screen during an operation. This means that the operation being
conducted is prohibited.
• Depending on the disc, certain operations may not be as
described in this manual. Check each disc owner’s manual for
more information.
• During playback of a 2-layered disc, pictures may stop
momentarily. This happens when the 1st layer switches to the
2nd layer. This is not a malfunction.
Introduction
Before Playing a Disc
1 Turn on the power of the amplifier and TV.
2 Turn the UD9004 power on.
Set the TV and amplifier function to UD9004 input.
b When playing back a bonus view, before turning on the power of
the UD9004, insert a SD Memory Card that has at least 1GB and
has been initialized by UD9004.
3
4 Insert a disc.
Displayed playback information changes between
the information bar and media player screen each
time DISPLAY button is pressed.
To erase display, press DISPLAY button until it
goes away.
b Displayed content differs depending on the media being played
back.
Also, the information displayed during playback and stop differs.
Information Bar Display
BD
Press the SD/DISC button on the main unit to set the
playback media mode to “DISC MODE”.
• Press OPEN/CLOSE button to open/close
the disc tray.
• Insert the disc with the side you want to play
facing down.
Title
1/1
Title Elapsed
DVD-A
Chapter
DVD-V
1/6
Time display
Disc information
Before Playing a SD Memory Card
Set the TV and amplifier function to UD9004 input.
Specifications
Open the door at the right side of the unit and insert the SD
Memory Card in the direction indicated by the arrow with the
label side up (vpage 6, 8).
3 Turn the UD9004 power on.
the SD/DISC button on the
4 Press
main unit to set the playback media
mode to “SD CARD MODE”.
The SD indicator on the front panel lights.
The playback media mode setting remains in the memory, even when
the power is set to standby.
DVD
00:05:52
Cursor
1 Turn on the power of the amplifier and TV.
2 Insert a SD Memory Card.
36
About Playback Information
b Displayed inside the frame at the top of the screen.
(See the next page.)
DivX
ENGLISH
nn Disc Information Display
•Title
•Chapter
•Track
Media Player Display
Title being played/total number of titles
Chapter being played/total number of
chapters
Group being played/total number of
groups
Track being played/total number of tracks
SA-CD
DATA DISC
nn Time Display
Image
CD
MP3
WMA
LPCM
Media
Track 2
Now Playing
Song
Artist
d, f, 0, 1 ··············································· Select
Playback mode
Track being played
Time Display
Video output signal format/resolution
Audio format being output
Number of audio channels that the
connected device can receive
Search Using Information Bar
•
Title
•
Artist name
•
Album title
MP3
WMA
AAC
About the time display and HDMI output signal display, see
“Information Bar Display” (vpage 36).
the playback title or chapter from the top
3 Select
menu for playback.
d, f, 0, 1 ··············································· Select
ENTER ················································· Playback
0 ~ 9, +10 ············································· Playback
Specifications
d, f, 0, 1 buttons to move the cursor to the
1 Use
item that you wish to search.
Use 0 ~ 9 and +10 buttons to enter a
2 value.
3 Press ENTER button.
SA-CD
•You can make the following settings on the disc
menu. (Settable items vary depending on the
disc.)
·· Subtitle language
·· Audio language
·· Audio format etc.
•During DVD-Video playback, press TOP MENU or POP UP MENU/
MENU button to display the menu.
If the menu continues, press d, f, 0, 1 buttons to get to the next
part.
Troubleshooting
In the orange color cursor area, when you enter the number that you
wish to search, that location is searched. There are 4 search modes,
“Title search”, “Chapter search”, “Group search” and “Track search”.
nn Disc Information Display
ENTER ················································· Playback
Album
nn HDMI Output Signal Display
HDMI1/HDMI2
•Video Info
•Audio Info
•Max Channel
preparation (“Before Playing a Disc”
1 Playback
vpage 36).
the various settings for playback
2 Make
on the disc menu.
Playback HDMI Control Function Information
Single Elapsed
00:25
AAC
DVD-V
Setup
•Title Elapsed
•Title Remain
•Chapter Elapsed
•Chapter Remain
•Group Elapsed
•Group Remain
•Track Elapsed
•Track Remain
BD
Connections
•Group
Playing BD and DVD-Video
Getting Started
About Playback Information
Search is executed and playback begins.
bbIf the input number information is not on the
disc, the current playback display reappears.
d, f, 0, 1 ··············································· Select
ENTER ················································· Decision
0 ~ 9, +10 ····································· Number entry
37
ENGLISH
Getting Started
Playing BD and DVD-Video
Disc Menus
Title 1
Top menu
Connections
Subtitle
Chapter 2
Audio Setup
Chapter 3
Angle
Chapter 4
Sub Story
Chapter 5
Top Menu
GExampleH Disc menu
Chapter 6
GExampleH Top menu
Setup
Playback HDMI Control Function Information
With BD, depending on the disc,
you can select title and chapter
from the popup menu.
Popup menu
n Playing Bonus View
Press MODE button to select the secondary video display you
wish to playback.
Off
1/X
2/X
X/X
GSelectable itemH
: Does not display Secondary Video.
Off
1/X z : Displays the first Secondary Video .
2/X z : Displays the second Secondary Video.
X/X z : Displays the X th Secondary Video.
z: “X” is the number of Secondary Videos recorded and differs
depending on the disc.
If you have so
mething to sa
y, see this pict
ure before you
Title 1
Title 2
Bonus title
GExampleH Popup menu
Main video
(primary video)
n Playing BD-Video Compatible with Bonus View
Troubleshooting
• With a disc that is compatible with bonus view (picture-in-picture),
besides the main video (primary video) stored on the disc, you can
play back the video director’s commentary and simultaneously
ongoing sub-story, as well as sub-video such as alternative camera
angle (secondary video).
• Some BD discs use SD cards as the recording memory for Bonus
View playback. While the UD9004 is in standby, mount the SD
Memory Card beforehand.
• The playback method, etc., is determined by the disc, and varies
depending on the disc. Refer to the operation guide of the relevant
disc.
Specifications
38
Sub video
(secondary video)
GExampleH Bonus view
• Insert or remove a SD Memory Card while the power is in standby.
If you insert a SD Memory Card while the power is ON, the SD
Memory Card may not be read.
• The SD card used for the Bonus View function must have a capacity
of 1GB or greater. Also the SD card must be initialized on the
UD9004 (vpage 32).
ENGLISH
SA-CD
Multi
bbPressing 1 button plays back the selected area/
layer.
nn When You View the Text or Playback Time
Display
See “Media Player Display” (vpage 37).
•When playing back disc whose selected area or layer does not
exist, select the playback area or layer in the order “Multi”, “Stereo”,
“CD”.
•The area/layer selected at SOUND MODE button remains in the
memory even when the power is turned off.
Search mode is displayed in the top right of the screen.
bbThe search mode changes each time you press SEARCH button.
Playback begins.
Group search mode
nn When You Look at the Playback Time Display
See “Media Player Display” (vpage 37).
Track search mode
the playback group and track
2 Select
from the top menu, and then play
back.
0 ~ 9, +10, ENTER
DVD-Audio Playback
DVD-A
preparation (“Before Playing
1 Playback
a Disc” vpage 36).
the part for playback with
2 Select
SOUND MODE button.
Plays back the group or track of the pressed
number
bbSee “Looking for Specific Sections Using the
Search Modes” (vpage 44) for instructions on
inputting numbers.
The search mode selected with this operation is memorized until the
standby or the disc tray is opened.
Audio :Plays back the audio part.
lays back the video part.
Video : P
Troubleshooting
a top menu is available, select the
3 Ifplayback
group and track from the top
Playback HDMI Control Function Information
CD
:Plays back the multi-channel area of
the HD layer.
:Plays back the 2-channel area of the
HD layer.
:Plays back the CD layer.
1
2 Press 1 button.
stop or during playback, select search mode
1 During
with SEARCH button.
Setup
Stereo
a Disc”
Playback preparation (“Before Playing a Disc”
vpage 36).
Change Group/Track
Connections
preparation (“Before Playing
1 Playback
vpage 36).
the playback area and layer
2 Select
with SOUND MODE button.
CD
Getting Started
CD Playback
Playing Back Super Audio CD
menu, and then play back.
d, f, 0, 1 ··············································· Select
ENTER ······························ Decision or playback
0 ~ 9, +10 ············································· Playback
Specifications
nn When You View the Text or Playback Time
Display
See “Information Bar Display” (vpage 36).
39
ENGLISH
Getting Started
DVD-Audio Playback
Bonus Group playback
DVD-Audio may have a bonus group that can be played back on entry
of a password.
Connections
Setup
1
the bonus group number with 0
2 Enter
~ 9, +10 buttons.
During stop, select “Group” with SEARCH button.
Playback HDMI Control Function Information
Group
3
Playback will begin from the 1st track of the
selected group.
bbThe password may also be entered on the
menu screen, so follow the instructions on the
screen.
enter
the
wrong
Press CLEAR button to erase the input number
and then enter the correct number.
Troubleshooting
Select Still Images
With DVD-Audio with still images, you can select images displayed
during playback.
Specifications
Press PAGE+ button during playback.
The next still image is displayed.
40
BD
DVD-A
MP3
DVD-V
WMA
DVD
AAC
SA-CD
LPCM
CD
DivX
nn About the File Display
SD
JPEG
This enables you to play back high quality audio by stopping the
video signal, etc., output, and outputting the analog audio signal
only.
Press PURE DIRECT button during stop,
and then select pure direct mode.
–/5
Using 0 ~ 9 buttons enter a 4-digit
password, and then press ENTER
button.
nn When you
password
File Playback
Playing Back High-Quality Audio
(Pure Direct Function)
Off
: This turns off the pure direct function.
: This turns off the digital signal output, video signal
output and display on the display screen.
User Preset 1 : Operates with the registered pure direct setting.
User Preset 2 (“Pure Direct Setup” vpage 30)
On
•You cannot use PURE DIRECT button while the GUI menu is
displayed.
•The pure direct setting returns to “Off” when the UD9004 is put in
standby mode.
The limits on the number of folders and files that can be displayed
by the UD9004 are as follows.
(The limited number includes the root folder.)
•Number of folder directory levels···················8 levels
•Number of folders················································· 999
•Number of files··················································· 9999
•Number of text display characters
· File name, Folder name········································· 32
· Artist name, title, etc.··········································· 60
bbText more than one line is scroll displayed.
bbIf characters not supported on the menu screen are included in a
file name, title, artist name or album title, those are not displayed
correctly.
ENGLISH
About folder and file displays
File Playback
MP3
WMA
AAC
DVD
CD
SD
LPCM
DivX
JPEG
nn File Browser Screen
All Track Mode
DATA DISC
f
Folder
File A
File B
A
B
C
D
E
F
G
File C
File D
File E
DivX File 1
JPEG File 1
bq
5
Folder Mode
Press 9 button to display the next page.
Press 8 button to display the previous page.
Selected file
File for playback
File types
LPCM file
MP3 file
WMA file
AAC file
JPEG file
DivX® file
Folder
Repeat playback mode
Repeat Off
Track Repeat
All Repeat
Press REPEAT
button.
Playback mode
Playback
Pause
Stop
Fast reverse
Fast forward
: Plays back all files in the media.
: Plays back files in the selected folder. The folder
icon is displayed in the playback mode indicator.
For playable media and files, see “Playable Media” (vpage 3, 4).
6 Selecting and playing back files.
d, f · ························································ Select
ENTER, 1 ························ Decision or playback
Operation during playback differs depending on the file being played
back. See “Operation During Playback” (vpage 42).
41
Specifications
All Track Mode
nn To Switch the Page Displayed
File C
File D
File E
DivX File 1
JPEG File 1
Troubleshooting
ENTER ································· To next level down
Press PROG/DIRECT button to select a playback
mode.
f
0, RETURN
RETURN ··································· To next level up
TOP MENU ································To the top level
Files inside
selected
folder
1, ENTER
d, f, 0, 1, ENTER · ·· Display screen selection
Folder A
File A
File B
b w
Select a folder of the data to be played
back and press ENTER button.
[1/12]
folder name
d
Random playback mode
Folder mode
DATA DISC
Current level
[1/18]
Current level folder/file list
Root/
Folder
Folder
Folder
Folder
Folder
Folder
Folder
GItem selected screenH
Playback HDMI Control Function Information
d
Load media.
The file browser screen will appear.
bbSee “Inserting a Disc” and “Inserting an SD
Memory Card” (vpage 6) for how to load
media
bbWhen file browser screen does not appear,
press POP UP MENU/MENU button.
4
GFile browser screenH
Media currently
playing back
Random playback off
Random playback on
Folder Mode
Setup
3
Selected folder number/
Total number of folders
: Playing disc
SD CARD MODE : Playing SD memory card
Press PROG/DIRECT
button.
Connections
1
SD/DISC button, and select the
2 Press
playback media mode.
DISC MODE
Press RANDOM
button.
Folder Mode
Turn the UD9004 power on.
Getting Started
File Playback
ENGLISH
Getting Started
File Playback
About Screen Display During Playback
Operation During Playback
Audio file and DivX® file operation
Display during Playback of Audio Files
Connections
MP3
Displays the JPEG image data for cover art,
etc., recorded on the file being played.
Setup
Track 2
Playback HDMI Control Function Information
Elapsed time and
remaining time
Album
File name/Artist name/
Album Title
LPCM
DivX
nn Changing the Still Image being Played Back
Press 8, 9 buttons.
•Before playback, or display of next image.
Press RANDOM button during stop, and then
press ENTER or 1 button.
Now Playing
nn Pausing the Display
Press 3 button.
•To cancel pause, press 1 button.
nn Playing Back Repeatedly (Repeat
Playback)
Song
Artist
Single Elapsed
00:25
AAC
nn Playback in Any Order (Random
Playback)
Track number
during playback
DATA DISC
WMA
nn Changing the Still Image Orientation
Press REPEAT button to select the repeat
playback mode.
Playback mode
display
•Set the image display time on the GUI menu with: “Display Setup”
– “Slide Show Time” (vpage 32).
•With a large image file, the display time may be longer than the set
time.
Press d, f, 0, 1 buttons.
d, f · ··············································180° rotation
DATA DISC
0 · ················································Rotate 90° left
1 · ············································· Rotate 90° right
NOTE
The display of JPEG image data for cover art, etc., recorded on the file
being played is valid when playing MP3 and AAC audio files.
Display of DivX® Files and JPEG Files
Displays video being played.
Track 2
Now Playing
nn Returning to Thumbnail Display Screen
Press POP UP MENU/MENU button.
Playing Back JPEG File (Still Image)
JPEG
Troubleshooting
Slide show playback of JPEG format still image files stored on CD-R/RW, DVD-R/-RW/+R/+RW disc and SD Memory Card.
POP UP MENU/MENU button while the file
1 Press
browser screen is displayed.
The thumbnail screen will appear.
Specifications
bbPressing POP UP MENU/MENU button while the thumbnail
screen is displayed returns you to the file browser screen.
Displays still image being played
1/25
d, f, 0, 1 buttons to select still
2 Use
images.
3 Press ENTER button.
Display selected image on full screen.
42
ENGLISH
Operations Enabled During Playback
MP3
DVD
WMA
SA-CD
AAC
CD
LPCM
SD
DivX
MP3
DVD
WMA
AAC
CD
LPCM
SD
DivX
During playback, press 8 or 9
button.
SA-CD
AAC
WMA
SA-CD
CD
LPCM
SD
DivX
Press 2 button during playback.
Playback stops.
8 button Playback begins from the start of the
chapter/track/file being played.
9 button Playback begins from the start of the
next chapter/track/file.
b Continue pressing and skip to the chapter/track/file with just the
number of times pressed.
n About Resume Function
BD
DVD-A
DVD-V
DVD
DivX
When playback is stopped, the stop position is
memorized.
• The “1” indicator flashes on the display. When
playing back data from the stop position, press
1 button while stop by the resume function.
Skipping to the start of a title or group may be prohibited depending
on the disc.
n To Cancel the Resume Function
Perform one of the following operations.
• Press 2 button during stop.
• Open the disc tray.
• Change the playback media mode with SD/DISC
button.
• Remove the SD Memory Card.
Specifications
DVD-V
DVD-V
DVD
Troubleshooting
DVD-A
DVD-A
DVD-V
MP3
Stop Playback (Resume Function)
BD
DVD-A
Playback HDMI Control Function Information
BD
BD
Setup
Pause Playback
Skipping to the Chapter/Track/File You
Want to Playback
If the video is blurred during pause, stop playback
and press SET UP button, then, on the GUI menu,
change “Display Setup” – “Still Mode” – “Field”
(vpage 32).
Connections
n Pause Playback (vpage 43)
n Stop Playback (Resume Function) (vpage 43)
n Skipping to the Chapter/Track/File You Want to
Playback (vpage 43)
n Looking for Specific Sections Using the Search
Modes (vpage 44)
n Memorizing Locations You Want to Replay (Marker
Function) (vpage 45)
n Fast Forward/Fast Reverse (vpage 45)
n Step-by-Step Playback (vpage 45)
n Slow Forward/Slow Reverse Playback (vpage
45)
n Playback in Any Order (Random Playback)
(vpage 46)
n Playing Back Repeatedly (Repeat Playback)
(vpage 46)
n Repeat Playback between Specified Points (A-B
Repeat) (vpage 46)
n Playing back in your preferred order (Program
Playback) (vpage 47)
n Switching Audio (vpage 47, 48)
n Changing the Subtitles and Subtitle Style (vpage
48)
n Switching the Angle (vpage 49)
n Changing the Brightness of the Display (Dimmer
Control) (vpage 49)
Getting Started
Operations Enabled During Playback
• The resume function does not work with menu playback or BD-J
(Blu-ray Disc Java) compatible disc.
• The resume function remains valid even when the standby mode is
set. For DivX® files, however, the resume function is cancelled even
when the standby mode is set.
• The resume function is cancelled when the power is turned off by
unplugging the power cord.
Press 3 button during playback.
The “3” indicator will light on the display.
b Resume normal playback by pressing 1 button.
43
ENGLISH
Getting Started
Operations Enabled During Playback
GSearch mode-compatible media and filesH
Looking for Specific Sections Using the
Search Modes
BD
DVD-A
Connections
MP3
Setup
1
DVD-V
WMA
DVD
AAC
SA-CD
LPCM
CD
DivX
Media / file
SD
JPEG
During playback, press SEARCH button, and then
search mode.
Playback HDMI Control Function Information
The search mode setting bar is displayed at the top of the
screen.
•The search mode changes each time the button is pressed.
BD
DVD-A
DVD-V
Search mode
Chapter search
Title search
Time search
Marker search b
Track search
Group search
SA-CD
DivX
CD
DVD
S
S
S
S
Chapter
S
S
S
S
S
S
S
S
S
– –/21
•When the entry mode for chapter/title/track/
group search continues for about 5 seconds with
no operation, it is cancelled.
•When the power is set to standby or the disc is
removed, the set marker is deleted.
nn Title search
Title
–/5
nn Track search
Track
– –/15
search condition entry
2 Conducting
or setting on the search mode setting
bar.
nn Group search
Troubleshooting
Group
–/5
Search specified location on completion of
entry.
0 ~ 9, +10 ····································· Number entry
nn Time search
ENTER ···································· Finalizes number
Time Search
–––:––:––
Total Time 10 : 15 11
0, 1 ·························· Marker number selection
Specifications
ENTER ······Finalizes the marker number or plays back
nn Marker search
CLEAR · ························· Marker number cancel
Marker
1 2 3 4 5 6 7 8 AC
Time – – : – – : – –
44
WMA
JPEG
AAC
bbAbout Marker Search
Plays back from your selected marker number.
nn Chapter search
MP3
LPCM
•Entering numbers
Entering 3············································3, ENTERz
Entering 26···············2, 6, ENTERz or +10, +10, 6
Entering 138································1, 3, 8, ENTERz
z: Depending on number of recorded songs or chapters, you don’t
need to use “ENTER” button.
S
•Search mode does not operate during program or random playback.
Use 8, 9 buttons to cue.
•Time search corresponds with title and track playback time. It is not
compatible chapter playback time.
•Search mode may not operate depending on the disc.
ENGLISH
nn To Play Back Memorized Locations
Memorizing Locations You Want to
Replay (Marker Function)
BD
DVD-V
DVD-A
DVD
SD
DivX
nn To erase markers
The disc advances frame by frame each time the
button is pressed.
nn To erase all markers
bbResume normal playback by pressing 1 button.
Select “AC” and press ENTER button.
Time – – : – – : – –
Use 0,
2 number.
1 buttons to select the
Marker
•Subtitles may not appear depending on the locations you have
memorized.
•The markers you have set will be erased if you turn the power to
standby or eject the disc.
•The marker function does not operate across titles and groups.
•Marker search can only be performed during playback.
1 2 3 4 5 6 7 8 AC
Slow Forward/Slow Reverse Playback
Time – – : – – : – –
bbNumbers you have already set will be displayed
as “
”.
3
Press ENTER button at the location
you want to memorize.
bbThe elapsed playing time at the set location is
displayed.
Time
1
3 4 5 6 7 8 AC
Fast Forward/Fast Reverse
BD
DVD-A
DVD-V
MP3
DVD
WMA
SA-CD
AAC
CD
LPCM
SD
DivX
During playback, press 6 or 7
button.
•The fast forward/fast reverse speed changes
each time the button is pressed.
•Speed varies with the disc and file.
BD
DVD-V
DVD
DivX
Press 6, 7 buttons during pause.
The speed changes each time the button is
pressed.
bbThe speed of the slow reverse playback is not
switched.
bbResume normal playback by pressing 1 button.
bbResume normal playback by pressing 1 button.
1 : 23 : 45
45
Specifications
•You cannot fast forward/fast reverse across files or tracks during
program or random playback.
•Fast forward/fast reverse may be disabled with some DivX® files.
•Audio is not output during fast forward/fast reverse of a BD or
DVD.
•Audio is not output during slow forward/slow reverse playback.
•If the video is blurred during slow forward/slow reverse playback,
stop playback and press SET UP button, then on the GUI menu,
change “Display Setup” – “Still Mode” – “Field” (vpage 32).
Troubleshooting
The location is registered for the selected
marker number.
Marker
•Step-by-step reverse playback is not available with
the UD9004.
•If the video is shaky during step-by-step playback,
stop playback, press SET UP button, then on the
GUI menu, change “Display Setup” – “Still Mode”
– “Field” (vpage 32).
Playback HDMI Control Function Information
1 2 3 4 5 6 7 8 AC
DivX
Press 3 button during pause.
Select the number you want to erase, and then
press CLEAR button.
The search mode setting bar is displayed at the top of the
screen.
Marker
DVD-V
Setup
During playback, press SEARCH button, and then
select “Marker”.
BD
Connections
You can attach a marker to a location you want to view or hear
again, so that playback begins at that location.
1
Step-by-Step Playback
Use 0, 1 buttons to select the marker number,
then press ENTER button.
Getting Started
Operations Enabled During Playback
ENGLISH
Getting Started
Operations Enabled During Playback
Playing Back Repeatedly
(Repeat Playback)
Playback in Any Order
(Random Playback)
SA-CD
CD
SD
MP3
Connections
1
Setup
2 Press 1 button to play back.
WMA
AAC
LPCM
BD
DivX
MP3
Press RANDOM button during stop.
The “RAND” lights on the display and “Random
Mode” is displayed on the screen.
DVD-A
Repeat Playback Between Specified
Points (A-B Repeat)
DVD-V
WMA
DVD
AAC
LPCM
Playback HDMI Control Function Information
Random playback may not be enabled depending on the disc.
DivX
SD
JPEG
The repeat mode icon is displayed at the top of the screen.
•The repeat mode changes each time the button is pressed.
Repeat mode
DATA DISC
2
Press RANDOM button during stop.
CD
1 Press REPEAT button during playback.
Track 2
nn Resuming Normal Playback
SA-CD
Song
About Repeat Mode
Settable repeat modes vary depending on the disc or file you are
playing back.
Troubleshooting
DVD-A
SA-CD
MP3
CD
WMA
DVD
AAC
LPCM
Display
DivX
Specifications
Mode
JPEG
Chapter repeat
Track repeat
Title repeat
Group repeat
All repeat
S
S
S
S
S
S
S
S
•Some repeat modes may not be accessible depending on the disc.
•Depending on the disc, even when set to repeat playback, the disc
may not return to the start of title or chapter, and may advance to
the next scene.
•Repeat playback is not available during A-B repeat playback.
46
DVD
SA-CD
CD
SD
DivX
playback, press REPEAT A-B button at the
1 During
desired starting point (A).
The “A–” indicator will light on the display.
bbTo cancel starting point (A), press CLEAR button.
bbTo resume normal playback, press REPEAT A-B
button, and select “Repeat Off”.
bbTo resume normal playback, press REPEAT
button, and select “Repeat Off”.
BD
DVD-V
The “B” indicator will light on the display, and
A-B repeat playback will commence.
Now Playing
DVD-V
DVD-A
the REPEAT A-B button again
2 Press
at the desired ending point (B).
Artist
Press REPEAT button
to select the
Album
Single Elapsed
repeat
mode.
00:35
Media/File
BD
•You cannot skip title/file with A-B repeat.
•If you perform a search operation during A-B repeat playback, A-B
repeat playback is cancelled.
•A-B repeat playback may not be enabled depending on the scene.
•A-B repeat playback of MP3/WMA/AAC/JPEG/LPCM files is not
available.
•A-B repeat playback is not available during repeat playback.
•A-B repeat playback may not be enabled depending on the DivX®
file.
ENGLISH
nn Erasing Programmed Tracks One by One
Playing Back in Your Preferred Order
(Program Playback)
SA-CD
your
3 Select
buttons.
Press CLEAR button during stop.
CD
nn Erasing All Programmed Contents
Press PROG/DIRECT button.
2/5 : Dolby Digital 3/2.1 Japanese
Primary
Secondary –/1 : Off
1 Press PROG/DIRECT button during stop.
2
+10
Enter
3 : 32
BD
DVD-A
DVD-V
DVD
CD
SD
DivX
With discs and files that have multiple audio track recording, you
can change the audio during playback.
With BD, you can set sub-track audio such as interactive audio and
commentary audio, etc., with “Secondary”.
Switching a BD’s Primary Audio/Secondary Audio
playback of an Primary Audio/Secondary
1 During
Audio title, press AUDIO button.
CLEAR
The audio number currently being played is displayed.
Clear
3 Press 1 button.
Playback begins in the programmed order.
•Depending on the disc, audio switching may be restricted to
operation of the disc menu. In this case, switch the audio on the
disc menu.
•Be sure to set “BD Audio Mode” to “Mix Audio Output” (vpage
33) for playing back secondary audio.
•Depending on the BD, even if picture-in-picture playback is set to
“Off”, Secondary Audio only may be output.
1/5 : Dolby Digital 3/2.1 English
Primary
Secondary –/1 : Off
2
Press d, f buttons, select “Primary”
or “Secondary”, and then press
ENTER button.
Troubleshooting
ENTER ········································ Decision entry
The setup screen disappears.
Audio
Enter the track numbers you want
to program on the program setting
screen.
0 ~ 9, +10 ··················································· Entry
4 Press AUDIO button.
Audio
Primary
1/5 : Dolby Digital 3/2.1 English
Secondary –/1 : Off
Press 2 button setting playback.
The program setting screen will appear.
You can also check the contents of the program, which appears on
the unit’s display. Press CALL button during stop.
Specifications
nn Checking the Program Contents
Playback HDMI Control Function Information
0-9
Total Time
Track
No.
11
12
13
14
15
16
17
18
19
20
Switching Audio
Setup
The “PROG” indicator lights on the display, and the program
setting screen appears.
Track 1 - 16
Track
5
2
3
--
Connections
Audio
You can program up to a maximum of 20 tracks.
PROGRAM
No.
1
2
3
4
5
6
7
8
9
10
desired audio language with d, f
Getting Started
Operations Enabled During Playback
bbIf multiple audio items are recorded, “the current
audio number/number of recorded audio items”
is displayed.
bbWhen “BD Audio Mode” is set to “HD Audio
Output” (vpage 33), “Secondary” audio is not
output.
47
ENGLISH
Getting Started
Operations Enabled During Playback
Audio Switching (Media Other than BD)
1
Press AUDIO button during playback.
The audio number currently being played is displayed.
Connections
GExampleH DVD
Audio
1/5
Setup
Playback HDMI Control Function Information
2
: Dolby Digital 3/2.1 English
Use d, f buttons to select audio
GExampleH DVD-Video
BD
: Dolby Digital 3/2.1 Japanese
3 Press AUDIO button.
The setup screen disappears.
Troubleshooting
•With DVD-R/-RW with bilingual soundtrack recording, you can
switch between “Main” (main audio) and “Sub” (secondary audio) or
“Main/Sub” (main audio + secondary audio).
•In CD audio mode, you can switch “Stereo”, “L-ch” (left channel) or
“R-ch” (right channel).
•With a DivX® file, “MP3” or “Dolby Digital” audio formats and the
number of recorded audio modes are displayed. “– – –“ appears for
audio other than these.
•With DTS-CD (5.1 music disc), you cannot switch audio modes.
SD
DivX
During playback of a disc or file with recorded subtitles, you can
switch subtitle on/off as well as subtitle language.
With BD, you can change the style of displayed subtitles.
Switching a BD’s Primary Subtitle/Secondary Subtitle
and Subtitle Style
1 Press SUBTITLE button during playback.
Subtitle
1/5 :
Primary
Secondary –/1 :
1:
Style
2
Off
With d, f buttons, select “Primary”,
“Secondary” and “Style”, and then
press ENTER button.
Subtitle
1/5 :
Primary
Secondary –/1 :
1:
Style
Off
Use d, f buttons to select your desired subtitle
3 language
and subtitle style.
Specifications
4 Press SUBTITLE button.
The setup screen disappears.
Selecting DVD-Video and DivX® file Subtitle
1 Press SUBTITLE button during playback.
The subtitle number currently being played is displayed.
Subtitle
–/5
: Off
Subtitle
1/5
: English
With a DivX® file, the currently playing subtitle number and number
of recorded subtitles are displayed, the language option is not
displayed.
English
1/5 :
Primary
Secondary –/1 :
1:
Style
•If a disc does not include subtitles and subtitle style, “Not Available”
is displayed.
•Depending on the disc, subtitle switching may be restricted to
operation of the disc menu. In this case, switch the subtitles on
the disc menu.
2 Use d, f buttons to select subtitle.
English
Subtitle
48
DVD-V
The subtitle number currently being played is displayed.
Audio
2/5
Changing the Subtitles and Subtitle
Style
English
Off
ENGLISH
Switching the Angle
BD
DVD-V
1 Press ANGLE button during playback.
The angle number currently being played is displayed.
the HDMI output terminal corresponding with
1 Set
the HDMI control function.
nn TV or AV Amp power is turned on by operating
the UD9004, and functions change with UD9004
input.
bbThe HDMI control function will work only on one of the 2 HDMI
output terminals on the UD9004.
1/3
2 Use d, f buttons to select angle.
nn Operating the UD9004 via the TV’s remote
control.
Angle
(When the TV’s remote control has player operation buttons)
2/3
NOTE
3 Press ANGLE button.
The setup screen disappears.
NOTE
Angle changing may be restricted, depending on the disc.
Press DIMMER button.
Normal
Dim
Dark
Off
bbPlease refer to the owner’s manual as regards setting of connected
devices.
bbCarry out Steps 2 and 3 should any of the equipment be
unplugged.
ensure that the UD9004’s HDMI video output is
4 Toprojected
on the TV screen, change the input function
of the TV and AV Amp.
you turn the TV’s power to standby, check that
5 When
the power of the UD9004 and AV Amp also goes on
standby.
If the HDMI control function does not operate properly, check the
following points.
•Is the TV or AV Amp compatible with the HDMI control function?
•Is the setting of the UD9004’s HDMI output terminal correct? (Step
1)
•Are the HDMI control function settings of all equipment correct?
(Step 3)
•After setting, did you add another HDMI device connection or
make any changes in the connections? In this case, perform setting
again.
Even when “Off” is selected, the status of operations that are
performed appears momentarily on the display if “Display Setup”
– “Temporary Display” on the GUI menu is set to “On” (vpage 32).
49
Specifications
The display brightness each time the button is
pressed.
On the GUI menu, set the UD9004 with “HDMI Setup” – “HDMI
Control” (vpage 26).
Troubleshooting
Changing the Brightness of the
Display (Dimmer Control)
•The HDMI control function controls operations of a TV that is
compatible with the HDMI control function. Make sure that the TV
and HDMI are connected when you perform HDMI control.
•Some functions may not operate depending on the connected TV
or AV Amp. Check the owner’s manual of each device for details
beforehand.
•When “Other Setup” – “Power Saving” on the GUI menu is set
to “Power Saving Standby” or “Normal Standby” (vpage 32),
the player’s power cannot be turned on using the HDMI control
function.
•When “HDMI Setup” – “HDMI Control” – “Power Off Control” on
the GUI menu is set to “Off” (vpage 26), the UD9004 is not set to
standby even if the connected device is in the standby mode.
the power on for all the equipment connected by
2 Turn
HDMI cable.
the HDMI control function for all equipment
3 Set
connected by HDMI cable.
Playback HDMI Control Function Information
nn Turning off the TV’s power turns the UD9004’s
power to standby.
On the GUI menu, set “HDMI Setup” – “HDMI Control” (vpage
26).
Setup
Angle
When you make an HDMI connection with a TV or AV Amp compatible
with UD9004 and HDMI control functions, you can perform the
following operations by setting the HDMI control function of each
device.
Connections
During playback of a BD or DVD-Video recorded with several
camera angles, you can change the angle.
HDMI Control Function
Getting Started
Operations Enabled During Playback
ENGLISH
Getting Started
Other Information
Connections
About Copyright Protection
Technology
Setup
This product incorporates copyright protection technology that is
protected by U.S. patents and other intellectual property rights.
Use of this copyright protection technology must be authorised by
Macrovision, and is intended for home and other limited viewing
uses only unless otherwise authorised by Macrovision. Reverse
engineering or disassembly is prohibited.
Trademark Information
This product uses the following technologies:
“Blu-ray Disc”
trademarks.
and
“
”
are
is a trademark of the DVD Format /
Logo licensing Corporation.
Playback HDMI Control Function Information
HDMI, the HDMI logo and High- Definition
Multimedia Interface are trademarks or
registered trademarks of HDMI Licensing
LLC.
Java and all other trademarks and logos
are trademarks or registered trademarks of
Sun Microsystems, Inc. in the United States
and/or other countries.
Manufactured under license from Dolby
Laboratories. Dolby, Pro Logic and the
double-D symbol (
) are trademarks of
Dolby Laboratories.
Troubleshooting
Manufactured
under
license
under
U.S. Patent #’s: 5,451,942; 5,956,674;
5,974,380; 5,978,762; 6,226,616; 6,487,535;
7,212,872; 7,333,929; 7,392,195; 7,272,567
& other U.S. and worldwide patents issued
& pending. DTS is a registered trademark
and the DTS logos, Symbol, DTS-HD and
DTS-HD Master Audio are trademarks of
DTS, Inc.© 1996-2008 DTS, Inc. All Rights
Reserved.
Specifications
Windows Media and the Windows logo
are trademarks or registered trademarks of
Microsoft Corporation in the United States
and/or other countries.
DivX, DivX Certified, and associated logos
are trademarks of DivX, Inc. and are used
under license.
50
®, HDCD®, High Definition
Compatible Digital® and Microsoft® are
either registered trademarks or trademarks
of Microsoft Corporation, Inc. in the United
States and/or other countries. HDCD system
manufactured under license from Microsoft
Corporation, Inc. This product is covered by
one or more of the following: In the USA:
5,479,168, 5,638,074, 5,640,161, 5,808,574,
5,838,274, 5,854,600, 5,864,311, 5,872,531,
and in Australia: 669114. Other patents
pending.
“AVCHD” and “AVCHD” logo is the
trademark of Panasonic Corporation and
Sony Corporation.
“BONUSVIEW” is the trademark of Blu-ray
Disc Association.
SDHC logo is a trademark.
ENGLISH
Language
A Abkhazian
Language
I
J
L
M
P
Q
R
Language
S Samoan
Sangho
Sanskrit
Scots Gaelic
Serbian
Serbo-Croatian
Sesotho
Setswana
Shona
Sindhi
Singhalese
Siswat
Slovak
Slovenian
Somali
Spanish
Sundanese
Swahili
Swedish
T Tagalog
Tajik
Tamil
Tatar
Telugu
Thai
Tibetan
Tigrinya
Tonga
Tsonga
Turkish
Turkmen
Twi
U Ukrainian
Urdu
Uzbek
V Vietnamese
Volapuk
W Welsh
Wolof
X Xhosa
Y Yiddish
Yoruba
Z Zulu
Code
6559
6553
6547
5350
6564
6554
6566
6660
6560
6550
6555
6565
6557
6558
6561
5165
6567
6569
6568
6658
6653
6647
6666
6651
6654
4861
6655
6661
6665
6664
6657
6669
6757
6764
6772
6855
6861
4971
6961
7054
5655
7161
7267
Specifications
O
5565
5560
5547
5551
5557
5347
5566
5647
5669
5760
5765
5757
6469
5771
6460
5761
5767
5861
5847
5868
5860
5866
5957
5953
5965
5958
5966
5955
5964
5961
5960
6047
6051
6061
6149
6164
6159
6247
6265
5247
6258
6266
6367
6459
6461
6467
Troubleshooting
N
Code
Playback HDMI Control Function Information
K
Icelandic
Indonesian
Interlingua
Interlingue
Inupiak
Irish
Italian
Japanese
Javanese
Kannada
Kashmiri
Kazakh
Kinyarwanda
Kirghiz
Kirundi
Korean
Kurdish
Laothian
Latin
Latvian; Lettish
Lingala
Lithuanian
Macedonian
Malagasy
Malay
Malayalam
Maltese
Maori
Marathi
Moldavian
Mongolian
Nauru
Nepali
Norwegian
Occitan
Oriya
Oromo (Afan)
Panjabi
Pashto; Pushto
Persian
Polish
Portuguese
Quechua
Rhaeto-Romance
Romanian
Russian
Setup
4748
4747
4752
6563
4759
4764
5471
4765
4771
4772
4847
5167
4860
5072
4854
4855
4864
4853
5971
4851
5759
4947
7254
4961
5464
4965
5047
6058
5160
5161
5166
5261
5256
5255
5264
5271
5358
5747
5051
5158
5758
5360
5367
5447
5569
5455
5467
Connections
Afar
Afrikaans
Albanian
Amharic
Arabic
Armenian
Assamese
Aymara
Azerbaijani
B Bashkir
Basque
Bengali;Bangla
Bhutani
Bihari
Bislama
Breton
Bulgarian
Burmese
Byelorussian
C Cambodian
Catalan
Chinese
Corsican
Croatian
Czech
D Danish
Dutch
E English
Esperanto
Estonian
F Faroese
Fiji
Finnish
French
Frisian
G Galician
Georgian
German
Greek
Greenlandic
Guarani
Gujarati
H Hausa
Hebrew
Hindi
Hungarian
Code
Getting Started
Language Code List
51
ENGLISH
Getting Started
Country Code List
Country
A AFGHANISTAN
Connections
Setup
Playback HDMI Control Function Information
B
Troubleshooting
Specifications
C
52
ÅLAND ISLANDS
ALBANIA
ALGERIA
AMERICAN SAMOA
ANDORRA
ANGOLA
ANGUILLA
ANTARCTICA
ANTIGUA AND BARBUDA
ARMENIA
ARUBA
AZERBAIJAN
BAHAMAS
BAHRAIN
BANGLADESH
BARBADOS
BELARUS
BELIZE
BENIN
BERMUDA
BHUTAN
BOLIVIA
BOSNIA AND HERZEGOVINA
BOTSWANA
BOUVET ISLAND
BRITISH INDIAN OCEAN
TERRITORY
BRUNEI DARUSSALAM
BULGARIA
BURKINA FASO
BURUNDI
CAMBODIA
CAMEROON
CAPE VERDE
CAYMAN ISLANDS
CENTRAL AFRICAN
REPUBLIC
CHAD
CHRISTMAS ISLAND
COCOS (KEELING) ISLANDS
COMOROS
CONGO
CONGO, THE DEMOCRATIC
REPUBLIC OF THE
COOK ISLANDS
COSTA RICA
CÔTE D’IVOIRE
CROATIA
Code
AF
AX
AL
DZ
AS
AD
AO
AI
AQ
AG
AM
AW
AZ
BS
BH
BD
BB
BY
BZ
BJ
BM
BT
BO
BA
BW
BV
IO
BN
BG
BF
BI
KH
CM
CV
KY
CF
TD
CX
CC
KM
CG
CD
CK
CR
CI
HR
Country
CUBA
CYPRUS
CZECH REPUBLIC
D DJIBOUTI
DOMINICA
DOMINICAN REPUBLIC
E ECUADOR
EGYPT
EL SALVADOR
EQUATORIAL GUINEA
ERITREA
ESTONIA
ETHIOPIA
F FALKLAND ISLANDS
(MALVINAS)
FAROE ISLANDS
FIJI
FRENCH GUIANA
FRENCH POLYNESIA
FRENCH SOUTHERN
TERRITORIES
G GABON
GAMBIA
GEORGIA
GHANA
GIBRALTAR
GREENLAND
GRENADA
GUADELOUPE
GUAM
GUATEMALA
GUERNSEY
GUINEA
GUINEA-BISSAU
GUYANA
H HAITI
HEARD ISLAND AND
MCDONALD ISLANDS
HOLY SEE (VATICAN CITY
STATE)
HONDURAS
HUNGARY
I ICELAND
IRAN, ISLAMIC REPUBLIC
OF
IRAQ
ISLE OF MAN
ISRAEL
J JAMAICA
JERSEY
Code
Country
Code
CU
CY
CZ
DJ
DM
DO
EC
EG
SV
GQ
ER
EE
ET
JORDAN
K KAZAKHSTAN
KENYA
KIRIBATI
KOREA, DEMOCRATIC
PEOPLE’S REPUBLIC OF
KUWAIT
KYRGYZSTAN
L LAO PEOPLE’S
DEMOCRATIC REPUBLIC
LATVIA
LEBANON
LESOTHO
LIBERIA
LIBYAN ARAB JAMAHIRIYA
LIECHTENSTEIN
LITHUANIA
M MACAO
MACEDONIA, THE FORMER
YUGOSLAV REPUBLIC OF
MADAGASCAR
MALAWI
MALDIVES
MALI
MALTA
MARSHALL ISLANDS
MARTINIQUE
MAURITANIA
MAURITIUS
MAYOTTE
MICRONESIA, FEDERATED
STATES OF
MOLDOVA
MONACO
MONGOLIA
MONTENEGRO
MONTSERRAT
MOROCCO
MOZAMBIQUE
MYANMAR
N NAMIBIA
NAURU
NEPAL
NETHERLANDS ANTILLES
NEW CALEDONIA
NICARAGUA
NIGER
NIGERIA
NIUE
JO
KZ
KE
KI
FK
FO
FJ
GF
PF
TF
GA
GM
GE
GH
GI
GL
GD
GP
GU
GT
GG
GN
GW
GY
HT
HM
VA
HN
HU
IS
IR
IQ
IM
IL
JM
JE
KP
KW
KG
LA
LV
LB
LS
LR
LY
LI
LT
MO
MK
MG
MW
MV
ML
MT
MH
MQ
MR
MU
YT
FM
MD
MC
MN
ME
MS
MA
MZ
MM
NA
NR
NP
AN
NC
NI
NE
NG
NU
Country
NORFOLK ISLAND
NORTHERN MARIANA
ISLANDS
O OMAN
P PALAU
PALESTINIAN TERRITORY,
OCCUPIED
PANAMA
PAPUA NEW GUINEA
PARAGUAY
PERU
PITCAIRN
PUERTO RICO
Q QATAR
R RÉUNION
ROMANIA
RWANDA
S SAINT BARTHÉLEMY
SAINT HELENA
SAINT KITTS AND NEVIS
SAINT LUCIA
SAINT MARTIN
SAINT PIERRE AND
MIQUELON
SAINT VINCENT AND THE
GRENADINES
SAMOA
SAN MARINO
SAO TOME AND PRINCIPE
SAUDI ARABIA
SENEGAL
SERBIA
SEYCHELLES
SIERRA LEONE
SLOVAKIA
SLOVENIA
SOLOMON ISLANDS
SOMALIA
SOUTH AFRICA
SOUTH GEORGIA AND
THE SOUTH SANDWICH
ISLANDS
SRI LANKA
SUDAN
SURINAME
SVALBARD AND JAN
MAYEN
SWAZILAND
SYRIAN ARAB REPUBLIC
Code
NF
MP
OM
PW
PS
PA
PG
PY
PE
PN
PR
QA
RE
RO
RW
BL
SH
KN
LC
MF
PM
VC
WS
SM
ST
SA
SN
RS
SC
SL
SK
SI
SB
SO
ZA
GS
LK
SD
SR
SJ
SZ
SY
Country
T TAJIKISTAN
TANZANIA, UNITED
REPUBLIC OF
TIMOR-LESTE
TOGO
TOKELAU
TONGA
TRINIDAD AND TOBAGO
TUNISIA
TURKEY
TURKMENISTAN
TURKS AND CAICOS
ISLANDS
TUVALU
U UGANDA
UKRAINE
UNITED ARAB EMIRATES
UNITED STATES MINOR
OUTLYING ISLANDS
URUGUAY
UZBEKISTAN
V VANUATU
VATICAN CITY STATE
VENEZUELA
VIET NAM
VIRGIN ISLANDS, BRITISH
VIRGIN ISLANDS, U.S.
W WALLIS AND FUTUNA
WESTERN SAHARA
Y YEMEN
Z ZAMBIA
ZIMBABWE
Code
TJ
TZ
TL
TG
TK
TO
TT
TN
TR
TM
TC
TV
UG
UA
AE
UM
UY
UZ
VU
VA
VE
VN
VG
VI
WF
EH
YE
ZM
ZW
ENGLISH
D
Deep Color
This technology allows expression of more number of colors than the
conventional 8 bits and can reproduce colors close to natural ones
without color streak.
DHCP (Dynamic Host Configuration Protocol)
This mechanism automatically perform network configuration such as
IP address for network devices including UD9004, PC, and broadband
router.
H
HDCP
When transmitting digital signals between devices, this copyright
protection technology encrypts the signals to prevent content from
being copied without authorization.
HDMI
This is an abbreviation of High-Definition Multimedia Interface, which
is an AV digital interface that can be connected to a TV or amplifier.
Video signal and audio signal can be connected using 1 cable.
I
Interlacing (interlaced scanning)
This conventional method used to project images on a TV displays 1
frame of image in half and half, respectively as 2 fields.
Interactive audio
Audio such as click sound that is generated during operation and is
recorded in the title of BD-Videos.
R
Rating
Depending on the age of the viewer, this function restricts playing
back of BD-Video or DVD-Video. UD9004 can be set to restrict viewing
in 0 to 254 level for BD-Video, and 1 to 8 level for DVD-Video.
Region code
This code indicates country or region where the BD or DVD-Video can
be played back.
S
Secondary audio
This is audio signals of comment of movie director and other data
recorded in the bonus view of BD-Video.
T
Title
This is the unit of content that consists of chapters of BD or DVD
-Video. Some BD or DVD-Video may include multiple titles.
53
Specifications
Chapter
This is a break intended by a producer who organizes the title of BD
or DVD-Video. The chapter search function searches the beginning
of this break.
P
Picture-in-picture
This BD-Video function allows you to view making or commentary
scenes in the secondary video while viewing the main story in the
primary video.
Popup menu
This menu recorded in BD software. While playing back a BD,
this menu can be displayed on the front of the screen and can be
operated.
Primary audio
This audio signal is recorded in the main story in BD-Video.
Progressive (sequential scanning)
This is a scanning system of video signal that displays 1 frame of
video as one image. Compared to the interlace system, this system
provides images with less flickering and bleeding.
Troubleshooting
C
F
Finalise
This is processing that enables playing back of disc of BD/DVD/CD,
which was recorded using a recorder, by other players.
M
MPEG
This is an abbreviation of Moving Picture Experts Group, which is
an international standard of the moving picture audio compression
method. Images of BD and DVD are recorded using this method.
Playback HDMI Control Function Information
B
BD-J (Java)
With BD-Videos, there are fun software with more interactive
functions (games) using Java applications.
Bit rate
This expresses the read amount per 1 second of video/audio data
recorded in a disc.
Blu-ray disc
This is one-side 1 layer disc having 25GB capacity and can record
high vision video movie and games.
Bonus View
Special images for BD-Videos. It includes comment of the movie
director, simultaneously developing sub-story, and images from
different angles.
L
LFE
This is an abbreviation of Low Frequency Effect, which is an output
channel that emphasizes low frequency effect sound. Surround
audio is intensified by outputting 20Hz to 120Hz deep bass.
Linear PCM
This signal is uncompressed PCM (Pulse Code Modulation) signal.
This is the same system as the CD audio but this uses 192kHz, 96kHz,
and 48kHz sampling frequencies in BD or DVD and provides higher
sound quality than CD.
Setup
A
Anamorphic lens
This lens enlarges the 16 : 9 image to 2.35 : 1 image when projecting
the image using a projector.
Aspect ratio
This is the length and width ratio of the TV screen. The conventional
TV's screen ratio is 4 : 3 and the wide screen TV's screen ratio is
16 : 9.
Dolby Digital (5.1ch Surround)
This is a stereophonic effect developed by Dolby Laboratories. This is
maximum 5.1 channels of independent multi-channel audio system.
Dolby Digital Plus
This is an extension version of Dolby Digital and is a high sound
quality digital audio technology adopted as an optional audio for Bluray disc.
Dolby TrueHD
This lossless coding technology is adopted as optional audio for Bluray disc and supports 7.1 channels.
Downmix
This function converts the number of channels of surround audio to
less number of channels and plays back.
DTS
This is an abbreviation of Digital Theater System, which is a digital
audio system developed by DTS. When playing back audio by
connecting this system with a device such as DTS amplifier, accurate
sound field position and realistic sound effect as if you are in a movie
theater can be obtained.
DTS-HD
This audio technology provides higher sound quality and enhanced
functionality than the conventional DTS and is adopted as an optional
audio for Blu-ray disc. This technology supports multi-channel, high
data transfer speed, high sampling frequency, and lossless audio
playback. Maximum 7.1 channels are supported in Blu-ray disc.
Dynamic range
The difference between the maximum undistorted sound level and
the minimum sound level that is discernible above the noise emitted
by the device.
Connections
Numerics
4:3 letterbox
When a wide (16 : 9) disc is played back by connecting a 4 : 3 TV and
the UD9004, this function plays back the image with black area at the
top and bottom.
4:3 pan-and-scan
When a wide (16 : 9) disc is played back by connecting a 4 : 3 TV and
the UD9004, this function cuts left and right of the played back image
to the 4 : 3 size according to the disc's control information.
Getting Started
Explanation of Terms
ENGLISH
Getting Started
Index
vNumerics
page
2ch Balanced Connection································································20
Connections
vA
page
Setup
Playback HDMI Control Function Information
Adjusting the Picture Quality···························································35
Analog 7.1ch Connection································································18
Analog Audio Connection································································20
Audio Format·············································································16, 17
Audio Mode·····················································································33
Audio Setup·····················································································27
Auto Power Mode············································································32
vB
page
BD································································································3, 53
BD-Video························································································3, 5
Bonus View················································································38, 53
Brightness of the Display································································49
vC
page
Troubleshooting
Cables Used for Connections··························································12
CD··································································································3, 5
CD-R/-RW·······················································································3, 5
Channel Level·············································································25, 28
Chapter························································································5, 53
Component Resolution····································································26
Component Video Output································································20
Country Code···················································································52
vD
page
Specifications
Deep Color·················································································25, 53
Digital Audio Connection·································································17
Digital Audio Output········································································29
DivX®·······························································································4,5
Dolby Digital·········································································16, 17, 53
Dolby Digital Plus·································································16, 17, 53
Dolby TrueHD·······································································16, 17, 53
Downmix····················································································29, 53
DTS······················································································16, 17, 53
DTS-HD················································································16, 17, 53
DVD-Audio·····················································································3, 5
DVD-R/-RW/+R/+RW······································································3, 5
DVD-Video······················································································3, 5
DVI-D Terminal·················································································14
Dynamic Range··········································································29, 53
vF
page
File··································································································4, 5
File Browser Screen·········································································41
Finalise·························································································4, 53
Firmware Update·············································································33
Folder·································································································5
vG
page
Group·································································································5
vH
page
HDCP·························································································16, 53
HD Layer····························································································5
HDMI····················································································12, 13, 53
HDMI Connection············································································13
HDMI Control Function····································································49
HDMI Setup·····················································································25
Home Theater Playback···································································11
vI
page
Information Bar Display···································································36
Interlacing························································································53
vJ
page
JPEG··································································································4
vL
page
Language Code················································································51
Language Setup···············································································25
Letter Box···················································································26, 53
LFE·····························································································28, 53
Linear PCM(LPCM)······························································16, 17, 53
LPCM···················································································16, 17, 53
vR
page
Rating·························································································31, 53
Region Code················································································3, 53
Remote Control Setting···································································32
Remote Control Unit··········································································7
Repeat Mode···················································································46
Restorer···························································································34
Resume Function·············································································43
vS
page
Screen Saver····················································································32
SD Memory Card···········································································4, 5
Search Mode···················································································44
Secondary Audio··············································································53
Setting HDMI Audio Output····························································15
Setting HDMI Video Output·····························································15
Source Direct···················································································29
Speaker Configuration·······························································25, 27
Subtitle·····························································································48
Super Audio CD·············································································3, 5
vT
page
page
Time Display····················································································37
Title······························································································5, 53
Track···································································································5
TV Aspect···················································································26, 53
Marker Function···············································································45
Menu Map·······················································································23
MP3························································································4, 16, 17
Multi linear PCM··············································································16
Vertical Stretch·················································································34
Video Setup······················································································26
vM
vN
page
Network·····················································································21, 31
vP
page
Pan Scan····················································································26, 53
Picture-in-Picture········································································38, 53
Playback(BD)····················································································37
54
Playback(DVD)··················································································37
Playback(Super Audio CD)·······························································39
Playback(CD)····················································································39
Playback(DVD-Audio)·······································································39
Playback(JPEG)················································································42
Power Saving···················································································32
Primary Audio···················································································53
Progressive················································································26, 53
Pure Direct·················································································30, 40
vV
vW
page
page
WMA··································································································4
vX
page
XLR·····························································································20, 30
ENGLISH
Cause / Countermeasure
Picture
appear.
does
4, 38
32
4, 38
–
30, 40
19
26
13, 14
8
30, 40
16
Picture
is
not •The picture may be slightly disturbed directly after fast-forwarding
displayed
or
is or reversing. This is not a malfunction.
disturbed.
•Connect the UD9004’s video/S-Video/component video output
Picture of a BD-Video either directly to the TV or to the TV via the AV Amp. Do not
or DVD-Video disc is connect via a VCR (video cassette recorder). Some discs include
in black and white.
copy prohibit signals, and when such discs are played via a VCR
the copy guard system may cause the picture to be disturbed.
•Is a disc that is not compatible with the player or a disc with
a different region number loaded? (This player supports region
code “A” for BD-Video discs, “1” or “ALL” for DVD-Video discs.)
33
–
19
3
No sound is heard or •Check the devices whose audio is connected and the speaker
the sound is hard to connections.
hear.
•Is the power of devices whose audio is connected turned on?
Is the input selection set to the input to which the UD9004 is
connected?
•Is the audio output properly selected?
11 ~ 22
Picture
freezes •When the disc is scratched or contaminated with fingerprints, the
momentarily during disc may not be played back correctly. Clean the disc or replace
playback.
with a non-scratched disc.
•There may be a problem with the data recorded on the disc.
6
Playback does not •Is there condensation inside the player or on the disc? (Let set for
start even when 1 is 1 to 2 hours with the power off.)
pressed, or starts but •When the disc is scratched or contaminated with fingerprints, the
stops immediately.
disc may not be played back correctly. Clean the disc or replace
with a non-scratched disc.
•Is the disc loaded upside-down? Load the disc properly, with the
side containing the signals to be played facing down.
•Is an unplayable disc loaded?
Subtitles are not •Subtitles cannot be displayed for BD-Video, DVD-Video or DivX®
displayed.
files that do not contain subtitles.
•Is the subtitle setting “Off”? Use a disc menu or to set the
SUBTITLE button displayed subtitle.
3
SD Memory Card •The format of the card does not match to this unit or the card is
cannot be read.
not compatible.
•Is the playback media mode set to “SD CARD MODE”?
Select “SD CARD MODE” at SD/DISC button.
–
13 ~ 21
–
6
6
3, 4
Specifications
Video and audio are •Check the connection of the HDMI cable.
not output with HDMI •Is the “HDMI” indicator of the display of the UD9004 lighting?
connection.
•Is the Pure Direct function set to “On”? Set to “Off”.
Also, is “Pure Direct Setup” – “Video Out” on the GUI menu set
to “Off” at the “User Preset 1” or “User Preset 2” setting? Set it
to “On”.
•Check whether the connected display device or other device
supports HDCP. This unit will not output a video signal unless the
other device supports HDCP. See the owner’s manual of your TV,
AV Amp, etc.
•Check that the setting of the HDMI video resolution supports the
resolution of the connected device. When set to “Auto”, UD9004
makes the setting automatically.
•Check that the HDMI mode setting matches the connected
content. The connection method of each HDMI mode is
different.
3, 9
not •Set “BD Audio Mode” to “HD Audio Output”.
Troubleshooting
not •Switch the TV's input setting to the external input connected to
the player.
•Is the Pure Direct function set to “On”? Set to “Off”.
Also, is “Pure Direct Setup” – “Video Out” on the GUI menu set
to “Off” at the “User Preset 1” or “User Preset 2” setting? Set it
to “On”.
•Check the connection of the video/S-Video/component video
cable.
•Does the “Video Setup” – “Component Resolution” setting on the
GUI menu match the connected device's resolution? Set it so that
it matches.
22
–
–
is
Page
Playback HDMI Control Function Information
Unable to play back •Does the SD Memory Card has more than 1GB of available
bonus view.
space?
•Has the SD Memory Card been initialized by the UD9004?
•Was the SD Memory Card inserted while the power of the unit
is on. (Insert the SD Memory Card while the UD9004 is in the
standby status.)
Page
HD audio
output.
Cause / Countermeasure
Setup
Symptom
Power does not turn •Check if the power cord is properly connected.
on.
•Plug the power supply cord into the power outlet.
•The safety protection device may be activated. Unplug the power
cord once, and wait for 5-10 seconds and then plug it in again.
•UD9004 enters the standby status by safety function when the
fan stops. Check the back of the set if something is disturbing
the fan rotation.
Symptom
Connections
If a problem should arise, first check the following:
1. Are the connections correct?
2. Is the set being operated as described in the owner’s manual?
3. Are the other components operating properly?
If this unit does not operate properly, check the items listed in the table below. Should the problem
persist, there may be a malfunction.
In this case, disconnect the power immediately and contact your store of purchase.
Getting Started
Troubleshooting
48
25
32
36
15
13, 14
55
ENGLISH
Getting Started
Symptom
Cause / Countermeasure
Page
Connections
Setup
Playback HDMI Control Function Information
No return to start-up •There may be an internal error. Set the power to standby, wait
screen when disc is awhile, then turn the power back on.
removed.
–
The set cannot be •Aim the remote control directly at infrared sensor window on the
operated with the front of the unit.
remote control unit. •Operate within a distance of 7 meters from the remote control
sensor.
•Remove the obstacle.
•Replace the batteries with new ones.
•Insert the batteries in the proper direction, checking the q and
w marks.
•Make the signal code of the remote control match to the signal
code of the unit.
7
Buttons do not work •Operations may not be permitted by the disc.
or the unit stops •The safety protection device may be activated. Unplug the power
responding.
cord once, and wait for 5-10 seconds and then plug it in again.
•Refer to the instructions of the disc.
–
–
7
–
7
7
7
–
Playable disc is not •The pickup lens may be dirty. Before requesting servicing, try
read.
cleaning the laser pickup with a commercially available lens
cleaner. (Do not use a cleaner with brush because it may damage
the lens.)
Angle
does
switch.
–
Troubleshooting
not •If a BD-Video or DVD-Video does not record multiple angles,
angle cannot be switched. Also, multiple angles may be recorded
for specific scenes.
49
Playback does not •Playback may be prohibited by the viewing restriction setting.
start when the title is Check the “Ratings” setting on the GUI menu.
selected.
31
The password for •On the GUI menu, perform the “Other Setup” – “Initialize”
rating level has been procedure.
forgotten.
33
Specifications
•Some function may not be used in some operation status and this is not failure of the unit. Read the
description in this Owner’s Manual for details on correct operations.
•The volume may differ from disc to disc. This is due to the differences in how the signals are recorded
on the disc, and is not a malfunction.
•During programmed playback, it is not possible to perform random playback or to start playback from
the desired track or file.
•Some functions are prohibited on some discs.
56
ENGLISH
nn General
Power supply :
Power consumption :
(vpage 32 “Power Saving”)
Playback HDMI Control Function Information
Remote control type :
Batteries :
Setup
nn Remote control unit
AC 120 V, 60 Hz
88 W
•When in Power Saving Standby : 0.3 W
•When in Normal Standby : 0.8 W
•When in HDMI Control Mode :
4 ~ 15 W (Changes according to connection status, etc.)
•When in Quick Start Mode :
15 ~ 30 W (Changes according to connection status, etc.)
Connections
Infrared pulse
AAA/R03 Type (three batteries)
146.5 (5-13/16)
163.5 (6-7/16)
440 (17-3/8)
17 (11/16)
399 (15-3/4)
409 (16-1/8)
7 (5/16)
nn Dimensions (Unit: mm (inch))
Troubleshooting
Specifications
Signal format :
NTSC
Applicable discs /memory cards : (1) BD-Video discs :
12 cm 1 side 1 layer, 12 cm 1 side 2 layers
(2) DVD-Video / DVD-Audio discs :
12 cm 1 side 1 layer, 12 cm 1 side 2 layers /
12 cm 2 sides 2 layers (1 side 1 layer)
8 cm 1 side 1 layer, 8 cm 1 side 2 layers /
8 cm 2 sides 2 layers (1 side 1 layer)
(3) Super Audio CDs :
12 cm 1 layer / 12 cm 2 layer / 12 cm Hybrid
(4) Compact Discs (CD-DA) :
12 cm / 8 cm discs
(5) Memory cards :
SD Memory Card / SDHC Memory Card / miniSD Card /
microSD Card
S-Video output :
Y output level : 1Vp-p (75 Ω/ohms)
C output level : 0.286 Vp-p
Output terminal : S-Video, 1 set
Video output :
Output level : 1Vp-p (75 Ω/ohms)
Output terminal : Pin-jack, 1 set
Component video output :
Y output level : 1Vp-p (75 Ω/ohms)
Pb/Cb output level / Pr/Cr output level : 0.648 Vp-p (75 Ω/ohms)
Output terminal : Pin-jack, 1 set
HDMI output :
Output terminal : 19-pin HDMI terminals, 2 sets
HDMI ver. 1.3a
(Deep Colour, Dolby Digital Plus, Dolby TrueHD, DTS-HD)
Analog audio output :
Output level : 2 Vrms (10 kΩ/kohms)
2 channels output terminal : XLR terminal, 1 set
7.1 channels output terminal : Pin-jack, 1 set
Audio output characteristics :
(1) Frequency response
q BD (Multi linear PCM) : 2Hz ~ 22kHz (48kHz sampling)
: 2Hz ~ 44kHz (96kHz sampling)
: 2Hz ~ 88kHz (192kHz sampling)
w DVD (Multi linear PCM) : 2Hz ~ 22kHz (48kHz sampling)
: 2Hz ~ 44kHz (96kHz sampling)
: 2Hz ~ 88kHz (192kHz sampling)
: 2Hz ~ 100kHz
e Super Audio CD
: 2Hz ~ 20kHz
r CD
(2) S/N ratio : 125dB
(3) Total harmonic distortion : 1kHz 0.0008%
(4) Dynamic range : 112dB
Digital audio output :
Optical digital output: Optical connector, 1 set
Coaxial digital output: Pin jack, 1 set
3 (1/8)
nn Audio performance
Getting Started
Specifications
nn Weight : 19.2kg
z For purposes of improvement, specifications and design are subject to change without notice.
CLASS 1 LASER PRODUCT
LUOKAN 1 LASERLAITE
KLASS 1 LASERAPPARAT
57
License
This section describes software license used for UD9004. To maintain the correct content, the original
(English) is used.
nExhibit-A
GNU GENERAL PUBLIC LICENSE
Version 2, June 1991
Copyright (C) 1989, 1991
Free Software Foundation, Inc. 59 Temple Place, Suite
330, Boston, MA 02111-1307 USA
Everyone is permitted to copy and distribute verbatim
copies of this license document, but changing it is not
allowed.
Preamble
The licenses for most software are designed to take away
your freedom to share and change it. By contrast, the
GNU General Public
License is intended to guarantee your freedom to share
and change free software--to make sure the software is
free for all its users. This General Public License applies
to most of the Free Software Foundations software and
to any other program whose authors commit to using it.
(Some other Free Software Foundation software is covered
by the GNU Library General Public License instead.) You
can apply it to your programs, too.
When we speak of free software, we are referring to
freedom, not price. Our General Public Licenses are
designed to make sure that you have the freedom to
distribute copies of free software (and charge for this
service if you wish), that you receive source code or can
get it if you want it, that you can change the software or
use pieces of it in new free programs; and that you know
you can do these things.
To protect your rights, we need to make restrictions that
forbid anyone to deny you these rights or to ask you to
surrender the rights. These restrictions translate to certain
responsibilities for you if you distribute copies of the
software, or if you modify it.
For example, if you distribute copies of such a program,
whether gratis or for a fee, you must give the recipients all
the rights that you have. You must make sure that they,
too, receive or can get the source code. And you must
show them these terms so they know their rights.
We protect your rights with two steps: (1) copyright the
software, and (2) offer you this license which gives you
legal permission to copy, distribute and/or modify the
software.
Also, for each author’s protection and ours, we want to
make certain that everyone understands that there is no
warranty for this free software. If the software is modified
by someone else and passed on, we want its recipients
to know that what they have is not the original, so that
any problems introduced by others will not reflect on the
original authors’ reputations.
Finally, any free program is threatened constantly by
software patents. We wish to avoid the danger that
redistributors of a free program will individually obtain
patent licenses, in effect making the program proprietary.
To prevent this, we have made it clear that any patent must
be licensed for everyone’s free use or not licensed at all.
The precise terms and conditions for copying, distribution
and modification follow.
1
LICENSE
TERMS
AND
CONDITIONS
FOR
COPYING,
DISTRIBUTION AND MODIFICATION
0. This License applies to any program or other work
which contains a notice placed by the copyright holder
saying it may be distributed under the terms of this
General Public License. The “Program”, below, refers
to any such program or work, and a “work based
on the Program” means either the Program or any
derivative work under copyright law: that is to say, a
work containing the Program or a portion of it, either
verbatim or with modifications and/or translated into
another language. (Hereinafter, translation is included
without limitation in the term “modification”.) Each
licensee is addressed as “you”.
Activities other than copying, distribution and
modification are not covered by this License; they
are outside its scope. The act of running the Program
is not restricted, and the output from the Program is
covered only if its contents constitute a work based
on the Program (independent of having been made by
running the Program). Whether that is true depends on
what the Program does.
1. You may copy and distribute verbatim copies of the
Program’s source code as you receive it, in any medium,
provided that you conspicuously and appropriately
publish on each copy an appropriate copyright notice
and disclaimer of warranty; keep intact all the notices
that refer to this License and to the absence of any
warranty; and give any other recipients of the Program
a copy of this License along with the Program.
You may charge a fee for the physical act of transferring
a copy, and you may at your option offer warranty
protection in exchange for a fee.
2. You may modify your copy or copies of the Program
or any portion of it, thus forming a work based on the
Program, and copy and distribute such modifications
or work under the terms of Section 1 above, provided
that you also meet all of these conditions:
a) You must cause the modified files to carry prominent
notices stating that you changed the files and the
date of any change.
b) You must cause any work that you distribute
or publish, that in whole or in part contains or is
derived from the Program or any part thereof, to be
licensed as a whole at no charge to all third parties
under the terms of this License.
c) If the modified program normally reads commands
interactively when run, you must cause it, when
started running for such interactive use in the most
ordinary way, to print or display an announcement
including an appropriate copyright notice and a
notice that there is no warranty (or else, saying
that you provide a warranty) and that users may
redistribute the program under these conditions,
and telling the user how to view a copy of this
License.
(Exception: if the Program itself is interactive but
does not normally print such an announcement,
your work based on the Program is not required to
print an announcement.)
These requirements apply to the modified work as
a whole. If identifiable sections of that work are not
derived from the Program, and can be reasonably
considered independent and separate works in
themselves, then this License, and its terms, do not
apply to those sections when you distribute them as
separate works. But when you distribute the same
sections as part of a whole which is a work based on
the Program, the distribution of the whole must be on
the terms of this License, whose permissions for other
licensees extend to the entire whole, and thus to each
and every part regardless of who wrote it.
Thus, it is not the intent of this section to claim rights
or contest your rights to work written entirely by you;
rather, the intent is to exercise the right to control the
distribution of derivative or collective works based on
the Program.
In addition, mere aggregation of another work not
based on the Program with the Program (or with a
work based on the Program) on a volume of a storage
or distribution medium does not bring the other work
under the scope of this License.
3. You may copy and distribute the Program (or a
work based on it, under Section 2) in object code or
executable form under the terms of Sections 1 and 2
above provided that you also do one of the following:
a) Accompany it with the complete corresponding
machine-readable source code, which must be
distributed under the terms of Sections 1 and 2
above on a medium customarily used for software
interchange; or,
b)Accompany it with a written offer, valid for at least
three years, to give any third party, for a charge no
more than your cost of physically performing source
distribution, a complete machine-readable copy of
the corresponding source code, to be distributed
under the terms of Sections 1 and 2 above on a
medium customarily used for software interchange;
or,
c) Accompany it with the information you received as
to the offer to distribute corresponding source code.
(This alternative is allowed only for noncommercial
distribution and only if you received the program in
object code or executable form with such an offer,
in accord with Subsection b above.)
The source code for a work means the preferred
form of the work for making modifications to it. For
an executable work, complete source code means all
the source code for all modules it contains, plus any
associated interface definition files, plus the scripts
used to control compilation and installation of the
executable.
However, as a special exception, the source code
distributed need not include anything that is normally
distributed (in either source or binary form) with the
major components (compiler, kernel, and so on) of the
operating system on which the executable runs, unless
that component itself accompanies the executable.
If distribution of executable or object code is made by
offering access to copy from a designated place, then
offering equivalent access to copy the source code from
the same place counts as distribution of the source
code, even though third parties are not compelled to
copy the source along with the object code.
4. You may not copy, modify, sublicense, or distribute
the Program except as expressly provided under this
License. Any attempt otherwise to copy, modify,
sublicense or distribute the Program is void, and will
automatically terminate your rights under this License.
However, parties who have received copies, or rights,
from you under this License will not have their licenses
terminated so long as such parties remain in full
compliance.
5. You are not required to accept this License, since you
have not signed it. However, nothing else grants you
permission to modify or distribute the Program or its
derivative works. These actions are prohibited by
law if you do not accept this License. Therefore, by
modifying or distributing the Program (or any work
based on the Program), you indicate your acceptance
of this License to do so, and all its terms and conditions
for copying, distributing or modifying the Program or
works based on it.
6. Each time you redistribute the Program (or any work
based on the Program), the recipient automatically
receives a license from the original licensor to copy,
distribute or modify the Program subject to these
terms and conditions. You may not impose any further
restrictions on the recipients’ exercise of the rights
granted herein.
You are not responsible for enforcing compliance by
third parties to this License.
7. If, as a consequence of a court judgment or allegation
of patent infringement or for any other reason (not
limited to patent issues), conditions are imposed on
you (whether by court order, agreement or otherwise)
that contradict the conditions of this License, they do
not excuse you from the conditions of this License. If
you cannot distribute so as to satisfy simultaneously
your obligations under this License and any other
pertinent obligations, then as a consequence you
may not distribute the Program at all. For example,
if a patent license would not permit royalty-free
redistribution of the Program by all those who receive
copies directly or indirectly through you, then the only
way you could satisfy both it and this License would
be to refrain entirely from distribution of the Program.
If any portion of this section is held invalid or
unenforceable under any particular circumstance,
the balance of the section is intended to apply and
the section as a whole is intended to apply in other
circumstances.
It is not the purpose of this section to induce you to
infringe any patents or other property right claims or
to contest validity of any such claims; this section has
the sole purpose of protecting the integrity of the free
software distribution system, which is implemented
by public license practices.
Many people have
made generous contributions to the wide range of
software distributed through that system in reliance
on consistent application of that system; it is up to
the author/donor to decide if he or she is willing to
distribute software through any other system and a
licensee cannot impose that choice.
This section is intended to make thoroughly clear what
is believed to be a consequence of the rest of this
License.
8. If the distribution and/or use of the Program is restricted
in certain countries either by patents or by copyrighted
interfaces, the original copyright holder who places
the Program under this License may add an explicit
geographical distribution limitation excluding those
countries, so that distribution is permitted only in or
among countries not thus excluded. In such case, this
License incorporates the limitation as if written in the
body of this License.
9. The Free Software Foundation may publish revised
and/or new versions of the General Public License
from time to time. Such new versions will be similar in
spirit to the present version, but may differ in detail to
address new problems or concerns.
Each version is given a distinguishing version number.
If the Program specifies a version number of this
License which applies to it and “any later version”, you
have the option of following the terms and conditions
either of that version or of any later version published
by the Free Software Foundation. If the Program does
not specify a version number of this License, you
may choose any version ever published by the Free
Software Foundation.
10.If you wish to incorporate parts of the Program into
other free programs whose distribution conditions are
different, write to the author to ask for permission. For
software which is copyrighted by the Free Software
Foundation, write to the Free Software Foundation; we
sometimes make exceptions for this. Our decision will
be guided by the two goals of preserving the free status
of all derivatives of our free software and of promoting
the sharing and reuse of software generally.
NO WARRANTY
11.BECAUSE THE PROGRAM IS LICENSED FREE
OF CHARGE, THERE IS NO WARRANTY FOR
THE PROGRAM, TO THE EXTENT PERMITTED BY
APPLICABLE LAW.
EXCEPT WHEN OTHERWISE
STATED IN WRITING THE COPYRIGHT HOLDERS
AND/OR OTHER PARTIES PROVIDE THE PROGRAM
“AS IS” WITHOUT WARRANTY OF ANY KIND,
EITHER EXPRESSED OR IMPLIED, INCLUDING, BUT
NOT LIMITED TO, THE IMPLIED WARRANTIES OF
MERCHANTABILITY AND FITNESS FOR A PARTICULAR
PURPOSE. THE ENTIRE RISK AS TO THE QUALITY
AND PERFORMANCE OF THE PROGRAM IS WITH
YOU. SHOULD THE PROGRAM PROVE DEFECTIVE,
YOU ASSUME THE COST OF ALL NECESSARY
SERVICING, REPAIR OR CORRECTION.
12.IN NO EVENT UNLESS REQUIRED BY APPLICABLE
LAW OR AGREED TO IN WRITING WILL ANY
COPYRIGHT HOLDER, OR ANY OTHER PARTY WHO
MAY MODIFY AND/OR REDISTRIBUTE THE PROGRAM
AS PERMITTED ABOVE, BE LIABLE TO YOU FOR
DAMAGES, INCLUDING ANY GENERAL, SPECIAL,
INCIDENTAL OR CONSEQUENTIAL DAMAGES
ARISING OUT OF THE USE OR INABILITY TO USE THE
PROGRAM (INCLUDING BUT NOT LIMITED TO LOSS
OF DATA OR DATA BEING RENDERED INACCURATE
OR LOSSES SUSTAINED BY YOU OR THIRD PARTIES
OR A FAILURE OF THE PROGRAM TO OPERATE WITH
ANY OTHER PROGRAMS), EVEN IF SUCH HOLDER
OR OTHER PARTY HAS BEEN ADVISED OF THE
POSSIBILITY OF SUCH DAMAGES.
END OF TERMS AND CONDITIONS
How to Apply These Terms to Your New Programs
If you develop a new program, and you want it to be of
the greatest possible use to the public, the best way to
achieve this is to make it free software which everyone
can redistribute and change under these terms.
To do so, attach the following notices to the program. It
is safest to attach them to the start of each source file
to most effectively convey the exclusion of warranty; and
each file should have at least the “copyright” line and a
pointer to where the full notice is found.
<one line to give the program’s name and a brief idea
of what it does.>
Copyright (C) <year> <name of author>
This program is free software; you can redistribute it
and/or modify it under the terms of the GNU General
Public License as published by the Free Software
Foundation; either version 2 of the License, or (at your
option) any later version.
This program is distributed in the hope that it will
be useful, but WITHOUT ANY WARRANTY; without
even the implied warranty of MERCHANTABILITY or
FITNESS FOR A PARTICULAR PURPOSE. See the
GNU General Public License for more details.
You should have received a copy of the GNU General
Public License along with this program; if not, write to
the Free Software Foundation, Inc., 59 Temple Place,
Suite 330, Boston, MA 02111-1307 USA
Also add information on how to contact you by electronic
and paper mail.
If the program is interactive, make it output a short notice
like this when it starts in an interactive mode:
Gnomovision version 69, Copyright (C) year name of
author
Gnomovision comes with ABSOLUTELY NO
WARRANTY; for details type ‘show w’. This is free
software, and you are welcome to redistribute it under
certain conditions; type ‘show c’ for details.
The hypothetical commands ‘show w’ and ‘show c’
should show the appropriate parts of the General Public
License. Of course, the commands you use may be called
something other than ‘show w’ and ‘show c’; they could
even be mouse-clicks or menu items--whatever suits your
program.
You should also get your employer (if you work as a
programmer) or your school, if any, to sign a “copyright
disclaimer” for the program, if necessary. Here is a
sample; alter the names:
Yoyodyne, Inc., hereby disclaims all copyright interest
in the program ‘Gnomovision’ (which makes passes at
compilers) written by James Hacker.
<signature of Ty Coon>, 1 April 1989
Ty Coon, President of Vice
This General Public License does not permit incorporating
your program into proprietary programs. If your program
is a subroutine library, you may consider it more useful to
permit linking proprietary applications with the library. If
this is what you want to do, use the GNU Library General
Public License instead of this License.
nExhibit-B
GNU LESSER GENERAL PUBLIC LICENSE
Version 2.1, February 1999
Copyright (C) 1991, 1999 Free Software Foundation, Inc.
59 Temple Place, Suite 330, Boston, MA 02111-1307
USA
Everyone is permitted to copy and distribute verbatim
copies of this license document, but changing it is not
allowed.
[This is the first released version of the Lesser GPL. It
also counts as the successor of the GNU Library Public
License, version 2, hence the version number 2.1.]
Preamble
The licenses for most software are designed to take away
your freedom to share and change it. By contrast, the
GNU General Public Licenses are intended to guarantee
your freedom to share and change free software--to make
sure the software is free for all its users.
This license, the Lesser General Public License, applies
to some specially designated software packages-typically libraries--of the Free Software Foundation and
other authors who decide to use it. You can use it too,
but we suggest you first think carefully about whether
this license or the ordinary General Public License is the
better strategy to use in any particular case, based on the
explanations below.
When we speak of free software, we are referring to
freedom of use, not price. Our General Public Licenses
are designed to make sure that you have the freedom
to distribute copies of free software (and charge for this
service if you wish); that you receive source code or can
get it if you want it; that you can change the software and
use pieces of it in new free programs; and that you are
informed that you can do these things.
To protect your rights, we need to make restrictions that
forbid distributors to deny you these rights or to ask you
to surrender these rights. These restrictions translate to
certain responsibilities for you if you distribute copies of
the library or if you modify it.
For example, if you distribute copies of the library,
whether gratis or for a fee, you must give the recipients
all the rights that we gave you. You must make sure that
they, too, receive or can get the source code. If you link
other code with the library, you must provide complete
object files to the recipients, so that they can relink them
with the library after making changes to the library and
recompiling it. And you must show them these terms so
they know their rights. We protect your rights with a twostep method: (1) we copyright the library, and (2) we offer
you this license, which gives you legal permission to copy,
distribute and/or modify the library.
To protect each distributor, we want to make it very clear
that there is no warranty for the free library. Also, if the
library is modified by someone else and passed on, the
recipients should know that what they have is not the
original version, so that the original author’s reputation
will not be affected by problems that might be introduced
by others.
Finally, software patents pose a constant threat to the
existence of any free program. We wish to make sure
that a company cannot effectively restrict the users of
a free program by obtaining a restrictive license from a
patent holder. Therefore, we insist that any patent license
obtained for a version of the library must be consistent
with the full freedom of use specified in this license.
Most GNU software, including some libraries, is covered
by the ordinary GNU General Public License. This license,
the GNU Lesser General Public License, applies to certain
designated libraries, and is quite different from the
ordinary General Public License. We use this license for
certain libraries in order to permit linking those libraries
into non-free programs.
When a program is linked with a library, whether statically or
using a shared library, the combination of the two is legally
speaking a combined work, a derivative of the original
library. The ordinary General Public License therefore
permits such linking only if the entire combination fits its
criteria of freedom. The Lesser General Public License
permits more lax criteria for linking other code with the
library.
We call this license the “Lesser” General Public License
because it does Less to protect the user’s freedom than
the ordinary General Public License. It also provides
other free software developers Less of an advantage over
competing non-free programs. These disadvantages are
the reason we use the ordinary General Public License
for many libraries. However, the Lesser license provides
advantages in certain special circumstances.
For example, on rare occasions, there may be a special
need to encourage the widest possible use of a certain
library, so that it becomes a de-facto standard. To achieve
this, non-free programs must be allowed to use the library.
A more frequent case is that a free library does the same
job as widely used non-free libraries. In this case, there
is little to gain by limiting the free library to free software
only, so we use the Lesser General Public License.
In other cases, permission to use a particular library in nonfree programs enables a greater number of people to use
a large body of free software. For example, permission to
use the GNU C Library in non-free programs enables many
more people to use the whole GNU operating system, as
well as its variant, the GNU/Linux operating system.
Although the Lesser General Public License is Less
protective of the users’ freedom, it does ensure that the
user of a program that is linked with the Library has the
freedom and the wherewithal to run that program using a
modified version of the Library.
The precise terms and conditions for copying, distribution
and modification follow. Pay close attention to the
difference between a “work based on the library” and a
“work that uses the library”.
The former contains code derived from the library,
whereas the latter must be combined with the library in
order to run.
LICENSE
2
TERMS
AND
CONDITIONS
FOR
COPYING,
DISTRIBUTION AND MODIFICATION
0. This License Agreement applies to any software library
or other program which contains a notice placed by
the copyright holder or other authorized party saying
it may be distributed under the terms of this Lesser
General Public License (also called “this License”).
Each licensee is addressed as “you”.
A “library” means a collection of software functions
and/or data prepared so as to be conveniently linked
with application programs (which use some of those
functions and data) to form executables.
The “Library”, below, refers to any such software
library or work which has been distributed under these
terms. A “work based on the Library” means either
the Library or any derivative work under copyright
law: that is to say, a work containing the Library or a
portion of it, either verbatim or with modifications and/
or translated straightforwardly into another language.
(Hereinafter, translation is included without limitation
in the term “modification”.)
“Source code” for a work means the preferred form of
the work for making modifications to it. For a library,
complete source code means all the source code for
all modules it contains, plus any associated interface
definition files, plus the scripts used to control
compilation and installation of the library.
Activities other than copying, distribution and
modification are not covered by this License; they are
outside its scope. The act of running a program using
the Library is not restricted, and output from such a
program is covered only if its contents constitute a
work based on the Library (independent of the use
of the Library in a tool for writing it). Whether that is
true depends on what the Library does and what the
program that uses the Library does.
1. You may copy and distribute verbatim copies of the
Library’s complete source code as you receive it, in
any medium, provided that you conspicuously and
appropriately publish on each copy an appropriate
copyright notice and disclaimer of warranty; keep
intact all the notices that refer to this License and to
the absence of any warranty; and distribute a copy of
this License along with the Library.
You may charge a fee for the physical act of transferring
a copy, and you may at your option offer warranty
protection in exchange for a fee.
2. You may modify your copy or copies of the Library or
any portion of it, thus forming a work based on the
Library, and copy and distribute such modifications
or work under the terms of Section 1 above, provided
that you also meet all of these conditions:
a) The modified work must itself be a software library.
b)You must cause the files modified to carry prominent
notices stating that you changed the files and the
date of any change.
c) You must cause the whole of the work to be licensed
at no charge to all third parties under the terms of
this License.
d)If a facility in the modified Library refers to a function
or a table of data to be supplied by an application
program that uses the facility, other than as an
argument passed when the facility is invoked, then
you must make a good faith effort to ensure that,
3
LICENSE
in the event an application does not supply such function
or table, the facility still operates, and performs whatever
part of its purpose remains meaningful.
(For example, a function in a library to compute
square roots has a purpose that is entirely welldefined independent of the application. Therefore,
Subsection 2d requires that any application-supplied
function or table used by this function must be
optional: if the application does not supply it, the
square root function must still compute square
roots.)
These requirements apply to the modified work
as a whole. If identifiable sections of that work are
not derived from the Library, and can be reasonably
considered independent and separate works in
themselves, then this License, and its terms, do not
apply to those sections when you distribute them as
separate works. But when you distribute the same
sections as part of a whole which is a work based on
the Library, the distribution of the whole must be on
the terms of this License, whose permissions for other
licensees extend to the entire whole, and thus to each
and every part regardless of who wrote it.
Thus, it is not the intent of this section to claim rights
or contest your rights to work written entirely by you;
rather, the intent is to exercise the right to control the
distribution of derivative or collective works based on
the Library.
In addition, mere aggregation of another work not
based on the Library with the Library (or with a work
based on the Library) on a volume of a storage or
distribution medium does not bring the other work
under the scope of this License.
3. You may opt to apply the terms of the ordinary GNU
General Public License instead of this License to a
given copy of the Library. To do this, you must alter all
the notices that refer to this License, so that they refer
to the ordinary GNU General Public License, version
2, instead of to this License. (If a newer version than
version 2 of the ordinary GNU General Public License
has appeared, then you can specify that version
instead if you wish.) Do not make any other change in
these notices.
Once this change is made in a given copy, it is
irreversible for that copy, so the ordinary GNU General
Public License applies to all subsequent copies and
derivative works made from that copy.
This option is useful when you wish to copy part of the
code of the Library into a program that is not a library.
4. You may copy and distribute the Library (or a portion
or derivative of it, under Section 2) in object code or
executable form under the terms of Sections 1 and
2 above provided that you accompany it with the
complete corresponding machine-readable source
code, which must be distributed under the terms of
Sections 1 and 2 above on a medium customarily used
for software interchange.
If distribution of object code is made by offering
access to copy from a designated place, then offering
equivalent access to copy the source code from the
same place satisfies the requirement to distribute
the source code, even though third parties are not
compelled to copy the source along with the object
code.
5. A program that contains no derivative of any portion
of the Library, but is designed to work with the Library
by being compiled or linked with it, is called a “work
that uses the Library”. Such a work, in isolation, is
not a derivative work of the Library, and therefore falls
outside the scope of this License.
However, linking a “work that uses the Library” with
the Library creates an executable that is a derivative
of the Library (because it contains portions of the
Library), rather than a “work that uses the library”. The
executable is therefore covered by this License.
Section 6 states terms for distribution of such
executables.
When a “work that uses the Library” uses material
from a header file that is part of the Library, the object
code for the work may be a derivative work of the
Library even though the source code is not.
Whether this is true is especially significant if the work
can be linked without the Library, or if the work is
itself a library. The threshold for this to be true is not
precisely defined by law.
If such an object file uses only numerical parameters,
data structure layouts and accessors, and small
macros and small inline functions (ten lines or less in
length), then the use of the object file is unrestricted,
regardless of whether it is legally a derivative work.
(Executables containing this object code plus portions
of the Library will still fall under Section 6.)
Otherwise, if the work is a derivative of the Library, you
may distribute the object code for the work under the
terms of Section 6. Any executables containing that
work also fall under Section 6, whether or not they are
linked directly with the Library itself.
6. As an exception to the Sections above, you may also
combine or link a “work that uses the Library” with the
Library to produce a work containing portions of the
Library, and distribute that work under terms of your
choice, provided that the terms permit modification
of the work for the customer’s own use and reverse
engineering for debugging such modifications.
You must give prominent notice with each copy of
the work that the Library is used in it and that the
Library and its use are covered by this License. You
must supply a copy of this License. If the work during
execution displays copyright notices, you must include
the copyright notice for the Library among them, as
well as a reference directing the user to the copy of
this License. Also, you must do one of these things:
a) Accompany the work with the complete
corresponding machine-readable source code
for the Library including whatever changes were
used in the work (which must be distributed under
Sections 1 and 2 above); and, if the work is an
executable linked with the Library, with the complete
machine-readable “work that uses the Library”, as
object code and/or source code, so that the user
can modify the Library and then relink to produce
a modified executable containing the modified
Library. (It is understood that the user who changes
the contents of definitions files in the Library will not
necessarily be able to recompile the application to
use the modified definitions.)
b)Use a suitable shared library mechanism for linking
with the Library. A suitable mechanism is one that
(1) uses at run time a copy of the library already
present on the user’s computer system, rather than
copying library functions into the executable, and
(2) will operate properly with a modified version of
the library, if the user installs one, as long as the
modified version is interface-compatible with the
version that the work was made with.
c) Accompany the work with a written offer, valid
for at least three years, to give the same user the
materials specified in Subsection 6a, above, for a
charge no more than the cost of performing this
distribution.
d)If distribution of the work is made by offering access
to copy from a designated place, offer equivalent
access to copy the above specified materials from
the same place.
e) Verify that the user has already received a copy of
these materials or that you have already sent this
user a copy.
For an executable, the required form of the “work that
uses the Library” must include any data and utility
programs needed for reproducing the executable from
it. However, as a special exception, the materials to be
distributed need not include anything that is normally
distributed (in either source or binary form) with the
major components (compiler, kernel, and so on) of the
operating system on which the executable runs, unless
that component itself accompanies the executable.
It may happen that this requirement contradicts the
license restrictions of other proprietary libraries that
do not normally accompany the operating system.
Such a contradiction means you cannot use both them
and the Library together in an executable that you
distribute.
7. You may place library facilities that are a work based on
the Library side-by-side in a single library together with
other library facilities not covered by this License, and
distribute such a combined library, provided that the
separate distribution of the work based on the Library
and of the other library facilities is otherwise permitted,
and provided that you do these two things:
a) Accompany the combined library with a copy of the
same work based on the Library, uncombined with
any other library facilities. This must be distributed
under the terms of the Sections above.
b)Give prominent notice with the combined library of
the fact that part of it is a work based on the Library,
and explaining where to find the accompanying
uncombined form of the same work.
8. You may not copy, modify, sublicense, link with, or
distribute the Library except as expressly provided
under this License. Any attempt otherwise to copy,
modify, sublicense, link with, or distribute the Library is
void, and will automatically terminate your rights under
this License. However, parties who have received
copies, or rights, from you under this License will not
have their licenses terminated so long as such parties
remain in full compliance.
9. You are not required to accept this License, since
you have not signed it. However, nothing else grants
you permission to modify or distribute the Library or
its derivative works. These actions are prohibited
by law if you do not accept this License. Therefore,
by modifying or distributing the Library (or any work
based on the Library), you indicate your acceptance of
this License to do so, and all its terms and conditions
for copying, distributing or modifying the Library or
works based on it.
10. Each time you redistribute the Library (or any work
based on the Library), the recipient automatically
receives a license from the original licensor to copy,
distribute, link with or modify the Library subject to
these terms and conditions. You may not impose
any further restrictions on the recipients’ exercise
of the rights granted herein. You are not responsible
for enforcing compliance by third parties with this
License.
11.If, as a consequence of a court judgment or allegation
of patent infringement or for any other reason (not
limited to patent issues), conditions are imposed on
you (whether by court order, agreement or otherwise)
that contradict the conditions of this License, they do
not excuse you from the conditions of this License. If
you cannot distribute so as to satisfy simultaneously
your obligations under this License and any other
pertinent obligations, then as a consequence you may
not distribute the Library at all. For example, if a patent
license would not permit royalty-free redistribution of
the Library by all those who receive copies directly or
indirectly through you, then the only way you could
satisfy both it and this License would be to refrain
entirely from distribution of the Library. If any portion
of this section is held invalid or unenforceable under
any particular circumstance, the balance of the section
is intended to apply, and the section as a whole is
intended to apply in other circumstances.
It is not the purpose of this section to induce you to
infringe any patents or other property right claims or
to contest validity of any such claims; this section has
the sole purpose of protecting the integrity of the free
software distribution system which is implemented
by public license practices.
Many people have
made generous contributions to the wide range of
software distributed through that system in reliance
on consistent application of that system; it is up to
the author/donor to decide if he or she is willing to
distribute software through any other system and a
licensee cannot impose that choice.
This section is intended to make thoroughly clear what
is believed to be a consequence of the rest of this
License.
12.If the distribution and/or use of the Library is restricted
in certain countries either by patents or by copyrighted
interfaces, the original copyright holder who places
the Library under this License may add an explicit
geographical distribution limitation excluding those
countries, so that distribution is permitted only in or
among countries not thus excluded. In such case, this
License incorporates the limitation as if written in the
body of this License.
13.The Free Software Foundation may publish revised
and/or new versions of the Lesser General Public
License from time to time. Such new versions will be
similar in spirit to the present version, but may differ in
detail to address new problems or concerns.
Each version is given a distinguishing version number.
If the Library specifies a version number of this
License which applies to it and “any later version”, you
have the option of following the terms and conditions
either of that version or of any later version published
by the Free Software Foundation. If the Library does
not specify a license version number, you may choose
any version ever published by the Free Software
Foundation.
14.If you wish to incorporate parts of the Library into
other free programs whose distribution conditions are
incompatible with these, write to the author to ask for
permission. For software which is copyrighted by the
Free Software Foundation, write to the Free Software
Foundation; we sometimes make exceptions for
this. Our decision will be guided by the two goals of
preserving the free status of all derivatives of our free
software and of promoting the sharing and reuse of
software generally.
NO WARRANTY
15.BECAUSE THE LIBRARY IS LICENSED FREE OF
CHARGE, THERE IS NO WARRANTY FOR THE LIBRARY,
TO THE EXTENT PERMITTED BY APPLICABLE LAW.
EXCEPT WHEN OTHERWISE STATED IN WRITING
THE COPYRIGHT HOLDERS AND/OR OTHER
PARTIES PROVIDE THE LIBRARY “AS IS” WITHOUT
WARRANTY OF ANY KIND, EITHER EXPRESSED OR
IMPLIED, INCLUDING, BUT NOT LIMITED TO, THE
IMPLIED WARRANTIES OF MERCHANTABILITY AND
FITNESS FOR A PARTICULAR PURPOSE. THE ENTIRE
RISK AS TO THE QUALITY AND PERFORMANCE OF
THE LIBRARY IS WITH YOU. SHOULD THE LIBRARY
PROVE DEFECTIVE, YOU ASSUME THE COST OF ALL
NECESSARY SERVICING, REPAIR OR CORRECTION.
16.IN NO EVENT UNLESS REQUIRED BY APPLICABLE
LAW OR AGREED TO IN WRITING WILL ANY
COPYRIGHT HOLDER, OR ANY OTHER PARTY WHO
MAY MODIFY AND/OR REDISTRIBUTE THE LIBRARY
AS PERMITTED ABOVE, BE LIABLE TO YOU FOR
DAMAGES, INCLUDING ANY GENERAL, SPECIAL,
INCIDENTAL OR CONSEQUENTIAL DAMAGES
ARISING OUT OF THE USE OR INABILITY TO USE THE
LIBRARY (INCLUDING BUT NOT LIMITED TO LOSS
OF DATA OR DATA BEING RENDERED INACCURATE
OR LOSSES SUSTAINED BY YOU OR THIRD PARTIES
OR A FAILURE OF THE LIBRARY TO OPERATE WITH
ANY OTHER SOFTWARE), EVEN IF SUCH HOLDER
OR OTHER PARTY HAS BEEN ADVISED OF THE
POSSIBILITY OF SUCH DAMAGES.
END OF TERMS AND CONDITIONS
How to Apply These Terms to Your New Libraries
If you develop a new library, and you want it to be of
the greatest possible use to the public, we recommend
making it free software that everyone can redistribute
and change. You can do so by permitting redistribution
under these terms (or, alternatively, under the terms of the
ordinary General Public License).
To apply these terms, attach the following notices to the
library. It is safest to attach them to the start of each source
file to most effectively convey the exclusion of warranty;
and each file should have at least the “copyright” line and
a pointer to where the full notice is found.
<one line to give the library’s name and a brief idea of
what it does.>
Copyright (C) <year> <name of author>
This library is free software; you can redistribute it and/or
modify it under the terms of the GNU Lesser General Public
License as published by the Free Software Foundation;
either version 2.1 of the License, or (at your option) any
later version.
This library is distributed in the hope that it will be useful,
but WITHOUT ANY WARRANTY; without even the implied
warranty of MERCHANTABILITY or FITNESS FOR A
PARTICULAR PURPOSE. See the GNU Lesser General
Public License for more details.
You should have received a copy of the GNU Lesser
General Public License along with this library; if not, write
to the Free Software Foundation, Inc., 59 Temple Place,
Suite 330, Boston, MA 02111-1307 USA
Also add information on how to contact you by electronic
and paper mail.
You should also get your employer (if you work as a
programmer) or your school, if any, to sign a “copyright
disclaimer” for the library, if necessary. Here is a sample;
alter the names:
Yoyodyne, Inc., hereby disclaims all copyright interest
in the library ‘Frob’ (a library for tweaking knobs) written
by James Random Hacker.
<signature of Ty Coon>, 1 April 1990
Ty Coon, President of Vice
That’s all there is to it!
nExhibit-D
nExhibit-C
README for release 6b of 27-Mar-1998
Copyright notice:
(C) 1995-2004 Jean-loup Gailly and Mark Adler
This software is provided ‘as-is’, without any express or
implied warranty. In no event will the authors be held liable
for any damages arising from the use of this software.
Permission is granted to anyone to use this software for
any purpose, including commercial applications, and to
alter it and redistribute it freely, subject to the following
restrictions:
1. The origin of this software must not be misrepresented;
you must not claim that you wrote the original
software. If you use this software in a product, an
acknowledgment in the product documentation would
be appreciated but is not required.
2. Altered source versions must be plainly marked as
such, and must not be misrepresented as being the
original software.
3. This notice may not be removed or altered from any
source distribution.
Jean-loup Gailly Mark Adler
jloup@gzip.org
madler@alumni.caltech.edu
If you use the zlib library in a product, we would appreciate
*not* receiving lengthy legal documents to sign. The
sources are provided for free but without warranty of
any kind. The library has been entirely written by Jeanloup Gailly and Mark Adler; it does not include third-party
code.
If you redistribute modified sources, we would appreciate
that you include in the file ChangeLog history information
documenting your changes. Please read the FAQ for
more information on the distribution of modified source
versions.
Copyright (c) 1998, 1999, 2000 Thai Open Source Software
Center Ltd and Clark Cooper
Copyright (c) 2001, 2002 Expat maintainers.
Permission is hereby granted, free of charge, to any
person obtaining a copy of this software and associated
documentation files (the “Software”), to deal in the
Software without restriction, including without limitation
the rights to use, copy, modify, merge, publish, distribute,
sublicense, and/or sell copies of the Software, and to
permit persons to whom the Software is furnished to do
so, subject to the following conditions:
The above copyright notice and this permission notice
shall be included in all copies or substantial portions of
the Software.
THE SOFTWARE IS PROVIDED “AS IS”, WITHOUT
WARRANTY OF ANY KIND, EXPRESS OR IMPLIED,
INCLUDING BUT NOT LIMITED TO THE WARRANTIES
OF MERCHANTABILITY, FITNESS FOR A PARTICULAR
PURPOSE AND NONINFRINGEMENT.
IN NO EVENT SHALL THE AUTHORS OR COPYRIGHT
HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES
OR OTHER LIABILITY, WHETHER IN AN ACTION OF
CONTRACT, TORT OR OTHERWISE, ARISING FROM, OUT
OF OR IN CONNECTION WITH THE SOFTWARE OR THE
USE OR OTHER DEALINGS IN THE SOFTWARE.
nExhibit-E
The Independent JPEG Group’s JPEG software
This distribution contains the sixth public release of the
Independent JPEG Group’s free JPEG software. You are
welcome to redistribute this software and to use it for any
purpose, subject to the conditions under LEGAL ISSUES,
below.
Serious users of this software (particularly those
incorporating it into larger programs) should contact IJG at
jpeg-info@uunet.uu.net to be added to our electronic mailing
list. Mailing list members are notified of updates and have a
chance to participate in technical discussions, etc.
This software is the work of Tom Lane, Philip Gladstone,
Jim Boucher, Lee Crocker, Julian Minguillon, Luis Ortiz,
George Phillips, Davide Rossi, Guido Vollbeding, Ge’
Weijers, and other members of the Independent JPEG
Group.
IJG is not affiliated with the official ISO JPEG standards
committee.
DOCUMENTATION ROADMAP
This file contains the following sections:
OVERVIEW
General description of JPEG and
the IJG software.
LEGAL ISSUES
Copyright, lack of warranty,
terms of distribution.
REFERENCES
Where to learn more about
JPEG.
ARCHIVE LOCATIONS Where to find newer versions of
this software.
RELATED SOFTWARE Other stuff you should get.
FILE FORMAT WARS
Software *not* to get.
TO DO
Plans for future IJG releases.
Other documentation files in the distribution are:
User documentation:
LICENSE
4
install.doc
How to configure and install the
IJG software.
usage.doc
Usage instructions for cjpeg,
djpeg, jpegtran, rdjpgcom, and
wrjpgcom.
*.1
Unix-style man pages for
programs (same info as usage.
doc).
wizard.doc
Advanced usage instructions for
JPEG wizards only.
change.log
Version-to-version
change
highlights.
Programmer and internal documentation:
libjpeg.doc
How to use the JPEG library in
your own programs.
example.c
Sample code for calling the
JPEG library.
structure.doc
Overview of the JPEG library’s
internal structure.
filelist.doc Road map of IJG files.
coderules.doc
Coding style rules --- please read
if you contribute code.
Please read at least the files install.doc and usage.doc.
Useful information can also be found in the JPEG FAQ
(Frequently Asked Questions) article. See ARCHIVE
LOCATIONS below to find out where to obtain the FAQ
article.
If you want to understand how the JPEG code works, we
suggest reading one or more of the REFERENCES, then
looking at the documentation files (in roughly the order
listed) before diving into the code.
OVERVIEW
This package contains C software to implement JPEG image
compression and decompression. JPEG (pronounced “jaypeg”) is a standardized compression method for full-color
and gray-scale images. JPEG is intended for compressing
“real-world” scenes; line drawings, cartoons and other
non-realistic images are not its strong suit. JPEG is lossy,
meaning that the output image is not exactly identical to
the input image. Hence you must not use JPEG if you
have to have identical output bits. However, on typical
photographic images, very good compression levels can
be obtained with no visible change, and remarkably high
compression levels are possible if you can tolerate a lowquality image. For more details, see the references, or just
experiment with various compression settings.
This software implements JPEG baseline, extendedsequential, and progressive
compression processes. Provision is made for supporting
all variants of these
processes, although some uncommon parameter settings
aren’t implemented yet.
For legal reasons, we are not distributing code for the
arithmetic-coding
variants of JPEG; see LEGAL ISSUES. We have made no
provision for supporting
the hierarchical or lossless processes defined in the
standard.
We provide a set of library routines for reading and writing
JPEG image files, plus two sample applications “cjpeg”
and “djpeg”, which use the library to perform conversion
between JPEG and some other popular image file
formats.
5
LICENSE
The library is intended to be reused in other applications.
In order to support file conversion and viewing software,
we have included considerable functionality beyond the
bare JPEG coding/decoding capability; for example, the
color quantization modules are not strictly part of JPEG
decoding, but they are essential for output to colormapped
file formats or colormapped displays. These extra functions
can be compiled out of the library if not required for a
particular application. We have also included “jpegtran”,
a utility for lossless transcoding between different JPEG
processes, and “rdjpgcom” and “wrjpgcom”, two simple
applications for inserting and extracting textual comments
in JFIF files.
The emphasis in designing this software has been on
achieving portability and flexibility, while also making it
fast enough to be useful. In particular, the software is
not intended to be read as a tutorial on JPEG. (See the
REFERENCES section for introductory material.) Rather,
it is intended to be reliable, portable, industrial-strength
code. We do not claim to have achieved that goal in every
aspect of the software, but we strive for it.
We welcome the use of this software as a component of
commercial products.
No royalty is required, but we do ask for an
acknowledgement in product documentation, as described
under LEGAL ISSUES.
LEGAL ISSUES
In plain English:
1. We don’t promise that this software works. (But if you
find any bugs, please let us know!)
2. You can use this software for whatever you want. You
don’t have to pay us.
3. You may not pretend that you wrote this software.
If you use it in a program, you must acknowledge
somewhere in your documentation that you’ve used
the IJG code.
In legalese:
The authors make NO WARRANTY or representation,
either express or implied, with respect to this software, its
quality, accuracy, merchantability, or fitness for a particular
purpose. This software is provided “AS IS”, and you, its
user, assume the entire risk as to its quality and accuracy.
This software is copyright (C) 1991-1998, Thomas G.
Lane.
All Rights Reserved except as specified below.
Permission is hereby granted to use, copy, modify, and
distribute this software (or portions thereof) for any
purpose, without fee, subject to these conditions:
(1) If any part of the source code for this software is
distributed, then this README file must be included,
with this copyright and no-warranty notice unaltered;
and any additions, deletions, or changes to the original
files must be clearly indicated in accompanying
documentation.
(2) If only executable code is distributed, then the
accompanying documentation must state that
“this software is based in part on the work of the
Independent JPEG Group”.
(3) Permission for use of this software is granted only if
the user accepts full responsibility for any undesirable
consequences; the authors accept NO LIABILITY for
damages of any kind.
These conditions apply to any software derived from or
based on the IJG code, not just to the unmodified library.
If you use our work, you ought to acknowledge us.
Permission is NOT granted for the use of any IJG author’s
name or company name in advertising or publicity relating
to this software or products derived from it. This software
may be referred to only as “the Independent JPEG Group’s
software”.
We specifically permit and encourage the use of this
software as the basis of commercial products, provided
that all warranty or liability claims are assumed by the
product vendor.
ansi2knr.c is included in this distribution by permission of
L. Peter Deutsch, sole proprietor of its copyright holder,
Aladdin Enterprises of Menlo Park, CA.
ansi2knr.c is NOT covered by the above copyright and
conditions, but instead by the usual distribution terms of
the Free Software Foundation; principally, that you must
include source code if you redistribute it. (See the file
ansi2knr.c for full details.) However, since ansi2knr.c is
not needed as part of any program generated from the
IJG code, this does not limit you more than the foregoing
paragraphs do.
The Unix configuration script “configure” was produced
with GNU Autoconf.
It is copyright by the Free Software Foundation but is
freely distributable.
The same holds for its supporting scripts (config.
guess, config.sub, ltconfig, ltmain.sh). Another support
script, install-sh, is copyright by M.I.T. but is also freely
distributable.
It appears that the arithmetic coding option of the JPEG
spec is covered by patents owned by IBM, AT&T, and
Mitsubishi. Hence arithmetic coding cannot legally be
used without obtaining one or more licenses. For this
reason, support for arithmetic coding has been removed
from the free JPEG software.
(Since arithmetic coding provides only a marginal gain
over the unpatented Huffman mode, it is unlikely that very
many implementations will support it.)
So far as we are aware, there are no patent restrictions on
the remaining code.
The IJG distribution formerly included code to read and
write GIF files.
To avoid entanglement with the Unisys LZW patent, GIF
reading support has been removed altogether, and the
GIF writer has been simplified to produce “uncompressed
GIFs”. This technique does not use the LZW algorithm; the
resulting GIF files are larger than usual, but are readable by
all standard GIF decoders.
We are required to state that
“The Graphics Interchange Format(c) is the Copyright
property of CompuServe Incorporated. GIF(sm) is a
Service Mark property of CompuServe Incorporated.”
REFERENCES
We highly recommend reading one or more of these
references before trying to understand the innards of the
JPEG software.
The best short technical introduction to the JPEG
compression algorithm is
Wallace, Gregory K. “The JPEG Still Picture
Compression Standard”, Communications of the ACM,
April 1991 (vol. 34 no. 4), pp. 30-44.
(Adjacent articles in that issue discuss MPEG motion
picture compression, applications of JPEG, and related
topics.) If you don’t have the CACM issue handy, a
PostScript file containing a revised version of Wallace’s
article is available at ftp://ftp.uu.net/graphics/jpeg/
wallace.ps.gz. The file (actually a preprint for an article
that appeared in IEEE Trans. Consumer Electronics) omits
the sample images that appeared in CACM, but it includes
corrections and some added material. Note: the Wallace
article is copyright ACM and IEEE, and it may not be used
for commercial purposes.
A somewhat less technical, more leisurely introduction
to JPEG can be found in “The Data Compression Book”
by Mark Nelson and Jean-loup Gailly, published by M&T
Books (New York), 2nd ed. 1996, ISBN 1-55851-434-1. This
book provides good explanations and example C code for
a multitude of compression methods including JPEG. It
is an excellent source if you are comfortable reading C
code but don’t know much about data compression
in general. The book’s JPEG sample code is far from
industrial-strength, but when you are ready to look at a full
implementation, you’ve got one here...
The best full description of JPEG is the textbook “JPEG
Still Image Data Compression Standard” by William
B. Pennebaker and Joan L. Mitchell, published by Van
Nostrand Reinhold, 1993, ISBN 0-442-01272-1. Price
US$59.95, 638 pp.
The book includes the complete text of the ISO JPEG
standards (DIS 10918-1 and draft DIS 10918-2).
This is by far the most complete exposition of JPEG in
existence, and we highly recommend it.
The JPEG standard itself is not available electronically;
you must order a paper copy through ISO or ITU. (Unless
you feel a need to own a certified official copy, we
recommend buying the Pennebaker and Mitchell book
instead; it’s much cheaper and includes a great deal of
useful explanatory material.)
In the USA, copies of the standard may be ordered from
ANSI Sales at (212) 642-4900, or from Global Engineering
Documents at (800) 854-7179. (ANSI doesn’t take credit
card orders, but Global does.) It’s not cheap: as of 1992,
ANSI was charging $95 for Part 1 and $47 for Part 2, plus
7% shipping/handling. The standard is divided into two
parts, Part 1 being the actual specification, while Part 2
covers compliance testing methods. Part 1 is titled “Digital
Compression and Coding of Continuous-tone Still Images,
Part 1: Requirements and guidelines” and has document
numbers ISO/IEC IS 10918-1, ITU-T T.81. Part 2 is titled
“Digital Compression and Coding of Continuous-tone Still
Images, Part 2: Compliance testing” and has document
numbers ISO/IEC IS 10918-2, ITU-T T.83.
Some extensions to the original JPEG standard are defined
in JPEG Part 3, a newer ISO standard numbered ISO/IEC
IS 10918-3 and ITU-T T.84. IJG currently does not support
any Part 3 extensions.
The JPEG standard does not specify all details of an
interchangeable file format. For the omitted details we
follow the “JFIF” conventions, revision 1.02. A copy of the
JFIF spec is available from:
Literature Department
C-Cube Microsystems, Inc.
1778 McCarthy Blvd.
Milpitas, CA 95035
phone (408) 944-6300, fax (408) 944-6314
A PostScript version of this document is available by FTP
at ftp://ftp.uu.net/graphics/jpeg/jfif.ps.gz. There is also a
plain text version at ftp://ftp.uu.net/graphics/jpeg/jfif.txt.
gz, but it is missing the figures.
The TIFF 6.0 file format specification can be obtained by
FTP from ftp://ftp.sgi.com/graphics/tiff/TIFF6.ps.gz. The
JPEG incorporation scheme found in the TIFF 6.0 spec of
3-June-92 has a number of serious problems.
IJG does not recommend use of the TIFF 6.0 design (TIFF
Compression tag 6).
Instead, we recommend the JPEG design proposed by
TIFF Technical Note #2 (Compression tag 7). Copies of
this Note can be obtained from ftp.sgi.com or from ftp://
ftp.uu.net/graphics/jpeg/. It is expected that the next
revision of the TIFF spec will replace the 6.0 JPEG design
with the Note’s design.
Although IJG’s own code does not support TIFF/JPEG,
the free libtiff library uses our library to implement TIFF/
JPEG per the Note. libtiff is available from ftp://ftp.sgi.
com/graphics/tiff/.
ARCHIVE LOCATIONS
The “official” archive site for this software is ftp.uu.net
(Internet address 192.48.96.9). The most recent released
version can always be found there in directory graphics/
jpeg. This particular version will be archived as ftp://ftp.
uu.net/graphics/jpeg/jpegsrc.v6b.tar.gz.
If you don’t have direct Internet access, UUNET’s archives
are also available via UUCP; contact help@uunet.uu.net
for information on retrieving files that way.
Numerous Internet sites maintain copies of the UUNET
files. However, only ftp.uu.net is guaranteed to have the
latest official version.
You can also obtain this software in DOS-compatible “zip”
archive format from the SimTel archives (ftp://ftp.simtel.
net/pub/simtelnet/msdos/graphics/), or on CompuServe in
the Graphics Support forum (GO CIS:GRAPHSUP), library
12 “JPEG Tools”. Again, these versions may sometimes
lag behind the ftp.uu.net release.
The JPEG FAQ (Frequently Asked Questions) article is a
useful source of general information about JPEG. It is
updated constantly and therefore is not included in this
distribution. The FAQ is posted every two weeks to
Usenet newsgroups comp.graphics.misc, news.answers,
and other groups.
It is available on the World Wide Web at http://www.faqs.
org/faqs/jpeg-faq/ and other news.answers archive sites,
including the official news.answers archive at rtfm.mit.
edu: ftp://rtfm.mit.edu/pub/usenet/news.answers/jpegfaq/.
If you don’t have Web or FTP access, send e-mail to mailserver@rtfm.mit.edu with body
send usenet/news.answers/jpeg-faq/part1
send usenet/news.answers/jpeg-faq/part2
RELATED SOFTWARE
Numerous viewing and image manipulation programs
now support JPEG. (Quite a few of them use this library
to do so.) The JPEG FAQ described above lists some of
the more popular free and shareware viewers, and tells
where to obtain them on Internet.
If you are on a Unix machine, we highly recommend Jef
Poskanzer’s free PBMPLUS software, which provides
many useful operations on PPM-format image files. In
particular, it can convert PPM images to and from a
wide range of other formats, thus making cjpeg/djpeg
considerably more useful. The latest version is distributed
by the NetPBM group, and is available from numerous
sites, notably ftp://wuarchive.wustl.edu/graphics/graphics/
packages/NetPBM/.
Unfortunately PBMPLUS/NETPBM is not nearly as portable
as the IJG software is; you are likely to have difficulty
making it work on any non-Unix machine.
A different free JPEG implementation, written by the
PVRG group at Stanford,
is available from ftp://havefun.stanford.edu/pub/jpeg/.
This program is designed for research and experimentation
rather than production use; it is slower, harder to use, and
less portable than the IJG code, but it is easier to read
and modify. Also, the PVRG code supports lossless
JPEG, which we do not. (On the other hand, it doesn’t do
progressive JPEG.)
FILE FORMAT WARS
Some JPEG programs produce files that are not compatible
with our library.
The root of the problem is that the ISO JPEG committee
failed to specify a concrete file format. Some vendors
“filled in the blanks” on their own, creating proprietary
formats that no one else could read. (For example, none
of the early commercial JPEG implementations for the
Macintosh were able to exchange compressed files.)
The file format we have adopted is called JFIF (see
REFERENCES). This format has been agreed to by a
number of major commercial JPEG vendors, and it has
become the de facto standard. JFIF is a minimal or “low
end” representation.
We recommend the use of TIFF/JPEG (TIFF revision 6.0
as modified by TIFF Technical Note #2) for “high end”
applications that need to record a lot of additional data
about an image. TIFF/JPEG is fairly new and not yet
widely supported, unfortunately.
The upcoming JPEG Part 3 standard defines a file format
called SPIFF.
SPIFF is interoperable with JFIF, in the sense that most
JFIF decoders should be able to read the most common
variant of SPIFF. SPIFF has some technical advantages
over JFIF, but its major claim to fame is simply that it is an
official standard rather than an informal one. At this point
it is unclear whether SPIFF will supersede JFIF or whether
JFIF will remain the de-facto standard. IJG intends to
support SPIFF once the standard is frozen, but we have
not decided whether it should become our default output
format or not.
(In any case, our decoder will remain capable of reading
JFIF indefinitely.)
Various proprietary file formats incorporating JPEG
compression also exist.
We have little or no sympathy for the existence of these
formats. Indeed, one of the original reasons for developing
this free software was to help force convergence on
common, open format standards for JPEG files. Don’t use
a proprietary file format!
TO DO
The major thrust for v7 will probably be improvement of
visual quality.
The current method for scaling the quantization tables
is known not to be very good at low Q values. We
also intend to investigate block boundary smoothing,
“poor man’s variable quantization”, and other means
of improving quality-vs-file-size performance without
sacrificing compatibility.
In future versions, we are considering supporting some
of the upcoming JPEG Part 3 extensions --- principally,
variable quantization and the SPIFF file format.
As always, speeding things up is of great interest.
Please send bug reports, offers of help, etc. to jpeg-info@
uunet.uu.net.
nExhibit-F
COPYRIGHT NOTICE, DISCLAIMER, and LICENSE:
If you modify libpng you may insert additional notices
immediately following this sentence.
libpng version 1.2.6, August 15, 2004, is Copyright (c)
2004 Glenn Randers-Pehrson, and is distributed according
to the same disclaimer and license as libpng-1.2.5 with
the following individual added to the list of Contributing
Authors
Cosmin Truta
libpng versions 1.0.7, July 1, 2000, through 1.2.5 - October
3, 2002, are Copyright (c) 2000-2002 Glenn RandersPehrson, and are distributed according to the same
disclaimer and license as libpng-1.0.6 with the following
individuals added to the list of Contributing Authors
Simon-Pierre Cadieux
Eric S. Raymond
Gilles Vollant
and with the following additions to the disclaimer:
There is no warranty against interference with your
enjoyment of the library or against infringement.
There is no warranty that our efforts or the library will
fulfill any of your particular purposes or needs. This
library is provided with all faults, and the entire risk of
satisfactory quality, performance, accuracy, and effort
is with the user.
libpng versions 0.97, January 1998, through 1.0.6, March
20, 2000, are Copyright (c) 1998, 1999 Glenn RandersPehrson, and are distributed according to the same
disclaimer and license as libpng-0.96, with the following
individuals added to the list of Contributing Authors:
Tom Lane
Glenn Randers-Pehrson
Willem van Schaik
libpng versions 0.89, June 1996, through 0.96, May 1997,
are Copyright (c) 1996, 1997 Andreas Dilger Distributed
according to the same disclaimer and license as libpng0.88, with the following individuals added to the list of
Contributing Authors:
John Bowler
Kevin Bracey
Sam Bushell
Magnus Holmgren
Greg Roelofs
Tom Tanner
libpng versions 0.5, May 1995, through 0.88, January
1996, are Copyright (c) 1995, 1996 Guy Eric Schalnat,
Group 42, Inc.
For the purposes of this copyright and license,“Contributing
Authors” is defined as the following set of individuals:
Andreas Dilger
Dave Martindale
Guy Eric Schalnat
Paul Schmidt
Tim Wegner
The PNG Reference Library is supplied “AS IS”. The
Contributing Authors and Group 42, Inc. disclaim all
warranties, expressed or implied, including, without
limitation, the warranties of merchantability and of fitness
for any purpose. The Contributing Authors and Group
42, Inc. assume no liability for direct, indirect, incidental,
special, exemplary, or consequential damages, which may
result from the use of the PNG Reference Library, even if
advised of the possibility of such damage.
Permission is hereby granted to use, copy, modify,
and distribute this source code, or portions hereof,
for any purpose, without fee, subject to the following
restrictions:
1. The origin of this source code must not be
misrepresented.
2. Altered versions must be plainly marked as such and
must not be misrepresented as being the original
source.
3. This Copyright notice may not be removed or altered
from any source or altered source distribution.
The Contributing Authors and Group 42, Inc. specifically
permit, without fee, and encourage the use of this source
code as a component to supporting the PNG file format
in commercial products. If you use this source code in
a product, acknowledgment is not required but would be
appreciated.
A “png_get_copyright” function is available, for convenient
use in “about” boxes and the like: printf(“%s”,png_get_
copyright(NULL)); Also, the PNG logo (in PNG format, of
course) is supplied in the files “pngbar.png” and “pngbar.
jpg (88x31) and “pngnow.png” (98x31).
Libpng is OSI Certified Open Source Software. OSI
Certified Open Source is a certification mark of the Open
Source Initiative.
Glenn Randers-Pehrson
glennrp@users.sourceforge.net
August 15, 2004
nExhibit-G
Copyright (c) 2001,2003 Keith Packard
Permission to use, copy, modify, distribute, and sell this
software and its documentation for any purpose is hereby
granted without fee, provided that the above copyright
notice appear in all copies and that both that copyright
notice and this permission notice appear in supporting
documentation, and that the name of Keith Packard not be
used in advertising or publicity pertaining to distribution
of the software without specific, written prior permission.
Keith Packard makes no representations about the
suitability of this software for any purpose. It is provided
“as is” without express or implied warranty.
KEITH PACKARD DISCLAIMS ALL WARRANTIES WITH
REGARD TO THIS SOFTWARE, INCLUDING ALL IMPLIED
WARRANTIES OF MERCHANTABILITY AND FITNESS, IN
NO EVENT SHALL KEITH PACKARD BE LIABLE FOR ANY
SPECIAL, INDIRECT OR CONSEQUENTIAL DAMAGES OR
ANY DAMAGES WHATSOEVER RESULTING FROM LOSS
OF USE, DATA OR PROFITS, WHETHER IN AN ACTION OF
CONTRACT, NEGLIGENCE OR OTHER TORTIOUS ACTION,
ARISING OUT OF OR IN CONNECTION WITH THE USE OR
PERFORMANCE OF THIS SOFTWARE.
LICENSE
6
nExhibit-H
The FreeType Project LICENSE
2002-Apr-11 Copyright 1996-2002 by David Turner, Robert
Wilhelm, and Werner Lemberg
Introduction
The FreeType Project is distributed in several archive
packages; some of them may contain, in addition to the
FreeType font engine, various tools and contributions
which rely on, or relate to, the FreeType Project.
This license applies to all files found in such packages,
and which do not fall under their own explicit license.
The license affects thus the FreeType font engine, the
test programs, documentation and makefiles, at the very
least.
This license was inspired by the BSD, Artistic, and IJG
(Independent JPEG Group) licenses, which all encourage
inclusion and use of free software in commercial and
freeware products alike. As a consequence, its main
points are that:
•We don’t promise that this software works. However,
we will be interested in any kind of bug reports. (‘as is’
distribution)
•You can use this software for whatever you want, in
parts or full form, without having to pay us. (‘royaltyfree’usage)
•You may not pretend that you wrote this software. If
you use it, or only parts of it, in a program, you must
acknowledge somewhere in your documentation that
you have used the FreeType code. (‘credits’)
We specifically permit and encourage the inclusion of this
software, with or without modifications, in commercial
products.
We disclaim all warranties covering The FreeType Project
and assume no liability related to The FreeType Project.
Finally, many people asked us for a preferred form for a
credit/disclaimer to use in compliance with this license.
We thus encourage you to use the following text:
Portions of this software are copyright © 1996-2002
The FreeType Project (www.freetype.org). All rights
reserved.
Legal Terms
0. Definitions
Throughout this license, the terms ‘package’,
‘FreeType Project’, and ‘FreeType archive’ refer to the
set of files originally distributed by the authors (David
Turner, Robert Wilhelm, and Werner Lemberg) as the
‘FreeType Project’, be they named as alpha, beta or
final release.
‘You’ refers to the licensee, or person using the project,
where ‘using’ is a generic term including compiling the
project’s source code as well as linking it to form a
‘program’ or ‘executable’.
This program is referred to as ‘a program using the
FreeType engine’.
This license applies to all files distributed in the original
FreeType Project, including all source code, binaries
and documentation, unless otherwise stated inthe
file in its original, unmodified form a distributed in the
original archive.
If you are unsure whether or not a particular file is
covered by this license, you must contact us to verify
this.
The FreeType Project is copyright (C) 1996-2000 by
David Turner,
Robert Wilhelm, and Werner Lemberg. All rights
reserved except as specified below.
7
LICENSE
1. No Warranty
THE FREETYPE PROJECT IS PROVIDED ‘AS IS’
WITHOUT WARRANTY OF ANY KIND, EITHER
EXPRESS OR IMPLIED, INCLUDING, BUT NOT
LIMITED TO, WARRANTIES OF MERCHANTABILITY
AND FITNESS FOR A PARTICULAR PURPOSE. IN NO
EVENT WILL ANY OF THE AUTHORS OR COPYRIGHT
HOLDERS BE LIABLE FOR ANY DAMAGES CAUSED
BY THE USE OR THE INABILITY TO USE, OF THE
FREETYPE PROJECT.
2. Redistribution
This license grants a worldwide, royalty-free, perpetual
and irrevocable right and license to use, execute,
perform, compile, display, copy, create derivative
works of, distribute and sublicense the FreeType Project
(in both source and object code forms) and derivative
works thereof for any purpose; and to authorize others
to exercise some or all of the rights granted herein,
subject to the following conditions:
•Redistribution of source code must retain this license
file (‘FTL.TXT’) unaltered; any additions, deletions or
changes to the original files must be clearly indicated in
accompanying documentation. The copyright notices
of the unaltered, original files must be preserved in all
copies of source files.
•Redistribution in binary form must provide a disclaimer
that states that the software is based in part of the
work of the FreeType Team, in the distribution
documentation. We also encourage you to put an
URL to the FreeType web page in your documentation,
though this isn’t mandatory.
These conditions apply to any software derived from or
based on the FreeType Project, not just the unmodified
files. If you use our work, you must acknowledge us.
However, no fee need be paid to us.
3. Advertising
Neither the FreeType authors and contributors nor
you shall use the name of the other for commercial,
advertising, or promotional purposes without specific
prior written permission.
We suggest, but do not require, that you use one or
more of the following phrases to refer to this software
in your documentation or advertising materials:
‘FreeType Project’, ‘FreeType Engine’, ‘FreeType library’,
or ‘FreeType Distribution’.
As you have not signed this license, you are not
required to accept it. However, as the FreeType
Project is copyrighted material, only this license, or
another one contracted with the authors, grants you
the right to use, distribute, and modify it.
Therefore, by using, distributing, or modifying the
FreeType Project, you indicate that you understand and
accept all the terms of this license.
4. Contacts
There are two mailing lists related to FreeType:
•freetype@freetype.org
Discusses general use and applications of FreeType,
as well as future and wanted additions to the library
and distribution.
If you are looking for support, start in this list if
you haven’t found anything to help you in the
documentation.
•devel@freetype.org
Discusses bugs, as well as engine internals, design
issues, specific licenses, porting, etc.
•http://www.freetype.org
Holds the current FreeType web page, which will allow
you to download our latest development version and
read online documentation.
You can also contact us individually at:
David Turner <david.turner@freetype.org>
Robert Wilhelm <robert.wilhelm@freetype.org>
Werner Lemberg <werner.lemberg@freetype.org>
nExhibit-I
zThis document is freely plagiarised from the ‘Artistic
Licence’, distributed as part of the Perl v4.0 kit by Larry
Wall, which is available from most major archive sites
This documents purpose is to state the conditions under
which these Packages (See definition below) viz: “Crack”,
the Unix Password Cracker, and “CrackLib”, the Unix
Password Checking library, which are held in copyright
by Alec David Edward Muffett, may be copied, such that
the copyright holder maintains some semblance of artistic
control over the development of the packages, while giving
the users of the package the right to use and distribute
the Package in a more-or-less customary fashion, plus the
right to make reasonable modifications.
So there.
Definitions:
A “Package” refers to the collection of files distributed by
the Copyright Holder, and derivatives of that collection of
files created through textual modification, or segments
thereof.
“Standard Version” refers to such a Package if it has not
been modified, or has been modified in accordance with
the wishes of the Copyright Holder.
“Copyright Holder” is whoever is named in the copyright
or copyrights for the package.
“You” is you, if you’re thinking about copying or distributing
this Package.
“Reasonable copying fee” is whatever you can justify
on the basis of media cost, duplication charges, time of
people involved, and so on. (You will not be required to
justify it to the Copyright Holder, but only to the computing
community at large as a market that must bear the fee.)
“Freely Available” means that no fee is charged for the
item itself, though there may be fees involved in handling
the item. It also means that recipients of the item may
redistribute it under the same conditions they received it.
1. You may make and give away verbatim copies of the
source form of the Standard Version of this Package
without restriction, provided that you duplicate all
of the original copyright notices and associated
disclaimers.
2. You may apply bug fixes, portability fixes and other
modifications derived from the Public Domain or from
the Copyright Holder. A Package modified in such a
way shall still be considered the Standard Version.
3. You may otherwise modify your copy of this Package
in any way, provided that you insert a prominent notice
in each changed file stating how and when AND WHY
you changed that file, and provided that you do at least
ONE of the following:
a) place your modifications in the Public Domain or
otherwise make them Freely Available, such as by
posting said modifications to Usenet or an equivalent
medium, or placing the modifications on a major
archive site such as uunet.uu.net, or by allowing the
Copyright Holder to include your modifications in
the Standard Version of the Package.
4.
5.
6.
7.
b)use the modified Package only within your
corporation or organization.
c) rename any non-standard executables so the
names do not conflict with standard executables,
which must also be provided, and provide separate
documentation for each non-standard executable
that clearly documents how it differs from the
Standard Version.
d)make other distribution arrangements with the
Copyright Holder.
You may distribute the programs of this Package in
object code or executable form, provided that you do
at least ONE of the following:
a) distribute a Standard Version of the executables
and library files, together with instructions (in the
manual page or equivalent) on where to get the
Standard Version.
b)accompany the distribution with the machinereadable source of the Package with your
modifications.
c) accompany any non-standard executables with their
corresponding Standard Version executables, giving
the non-standard executables non-standard names,
and clearly documenting the differences in manual
pages (or equivalent), together with instructions on
where to get the Standard Version.
d)make other distribution arrangements with the
Copyright Holder.
You may charge a reasonable copying fee for any
distribution of this Package. You may charge any fee
you choose for support of this Package.
YOU MAY NOT CHARGE A FEE FOR THIS PACKAGE
ITSELF. However, you may distribute this Package in
aggregate with other (possibly commercial) programs
as part of a larger (possibly commercial) software
distribution provided that YOU DO NOT ADVERTISE
this package as a product of your own.
The name of the Copyright Holder may not be used
to endorse or promote products derived from this
software without specific prior written permission.
THIS PACKAGE IS PROVIDED “AS IS” AND WITHOUT
ANY
EXPRESS
OR
IMPLIED
WARRANTIES,
INCLUDING, WITHOUT LIMITATION, THE IMPLIED
WARRANTIES OF MERCHANTIBILITY AND FITNESS
FOR A PARTICULAR PURPOSE.
nExhibit-J
Unless otherwise “explicitly” stated, the following text
describes the licensed conditions under which the contents
of this libcap release may be used and distributed:
Redistribution and use in source and binary forms of libcap,
with or without modification, are permitted provided that
the following conditions are met:
1. Redistributions of source code must retain any existing
copyright notice, and this entire permission notice in
its entirety, including the disclaimer of warranties.
2. Redistributions in binary form must reproduce all prior
and current copyright notices, this list of conditions,
and the following disclaimer in the documentation
and/or other materials provided with the distribution.
3. The name of any author may not be used to endorse or
promote products derived from this software without
their specific prior written permission.
ALTERNATIVELY, this product may be distributed under
the terms of the GNU General Public License, in which
case the provisions of the GNU GPL are required INSTEAD
OF the above restrictions. (This clause is necessary due
to a potential conflict between the GNU GPL and the
restrictions contained in a BSD-style copyright.)
THIS SOFTWARE IS PROVIDED “AS IS” AND ANY
EXPRESS OR IMPLIED WARRANTIES, INCLUDING,
BUT NOT LIMITED TO, THE IMPLIED WARRANTIES OF
MERCHANTABILITY AND FITNESS FOR A PARTICULAR
PURPOSE ARE DISCLAIMED.
IN NO EVENT SHALL THE AUTHOR(S) BE LIABLE FOR ANY
DIRECT, INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY,
OR CONSEQUENTIAL DAMAGES (INCLUDING, BUT NOT
LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS
OR SERVICES; LOSS OF USE, DATA, OR PROFITS; OR
BUSINESS INTERRUPTION) HOWEVER CAUSED AND ON
ANY THEORY OF LIABILITY, WHETHER IN CONTRACT,
STRICT LIABILITY, OR TORT (INCLUDING NEGLIGENCE
OR OTHERWISE) ARISING IN ANY WAY OUT OF THE
USE OF THIS SOFTWARE, EVEN IF ADVISED OF THE
POSSIBILITY OF SUCH DAMAGE.
nExhibit-K
Copyright 1995 by Wietse Venema. All rights reserved.
Some individual files may be covered by other copyrights.
This material was originally written and compiled by
Wietse Venema at Eindhoven University of Technology,
The Netherlands, in 1990, 1991, 1992, 1993, 1994 and
1995.
Redistribution and use in source and binary forms are
permitted provided that this entire copyright notice is
duplicated in all such copies.
This software is provided “as is” and without any expressed
or implied warranties, including, without limitation, the
implied warranties of merchantibility and fitness for any
particular purpose.
nExhibit-L
Copyright (c) 1989 The Regents of the University of
California.
All rights reserved.
Redistribution and use in source and binary forms, with
or without modification, are permitted provided that the
following conditions are met:
1. Redistributions of source code must retain the
above copyright notice, this list of conditions and the
following disclaimer.
2. Redistributions in binary form must reproduce the
above copyright notice, this list of conditions and the
following disclaimer in the documentation and/or other
materials provided with the distribution.
3. All advertising materials mentioning features or
use of this software must display the following
acknowledgement:
This product includes software developed by the
University of California, Berkeley and its contributors.
4. Neither the name of the University nor the names of
its contributors may be used to endorse or promote
products derived from this software without specific
prior written permission.
THIS SOFTWARE IS PROVIDED BY THE REGENTS AND
CONTRIBUTORS “AS IS” AND ANY EXPRESS OR IMPLIED
WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE
IMPLIED WARRANTIES OF MERCHANTABILITY AND
FITNESS FOR A PARTICULAR PURPOSE ARE DISCLAIMED.
IN NO EVENT SHALL THE REGENTS OR CONTRIBUTORS
BE LIABLE FOR ANY DIRECT, INDIRECT, INCIDENTAL,
SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES
(INCLUDING, BUT NOT LIMITED TO, PROCUREMENT
OF SUBSTITUTE GOODS OR SERVICES; LOSS OF USE,
DATA, OR PROFITS; OR BUSINESS INTERRUPTION)
HOWEVER CAUSED AND ON ANY THEORY OF LIABILITY,
WHETHER IN CONTRACT, STRICT LIABILITY, OR TORT
(INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN
ANY WAY OUT OF THE USE OF THIS SOFTWARE, EVEN
IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE.
nExhibit-M
Copyright (c) 1998 Red Hat Software
Permission is hereby granted, free of charge, to any
person obtaining a copy of this software and associated
documentation files (the “Software”), to deal in the
Software without restriction, including without limitation
the rights to use, copy, modify, merge, publish, distribute,
sublicense, and/or sell copies of the Software, and to
permit persons to whom the Software is furnished to do
so, subject to the following conditions:
The above copyright notice and this permission notice
shall be included in all copies or substantial portions of
the Software.
THE SOFTWARE IS PROVIDED “AS IS”, WITHOUT
WARRANTY OF ANY KIND, EXPRESS OR IMPLIED,
INCLUDING BUT NOT LIMITED TO THE WARRANTIES
OF MERCHANTABILITY, FITNESS FOR A PARTICULAR
PURPOSE AND NONINFRINGEMENT. IN NO EVENT
SHALL THE X CONSORTIUM BE LIABLE FOR ANY
CLAIM, DAMAGES OR OTHER LIABILITY, WHETHER
IN AN ACTION OF CONTRACT, TORT OR OTHERWISE,
ARISING FROM, OUT OF OR IN CONNECTION WITH THE
SOFTWARE OR THE USE OR OTHER DEALINGS IN THE
SOFTWARE.
Except as contained in this notice, the name of the X
Consortium shall not be used in advertising or otherwise
to promote the sale, use or other dealings in this
Software without prior written authorization from the X
Consortium.
nExhibit-N
Copyright (c) 2004-2005 by Internet Systems Consortium,
Inc. (“ISC”)
Copyright (c) 1995-2003 by Internet Software Consortium
Permission to use, copy, modify, and distribute this
software for any purpose with or without fee is hereby
granted, provided that the above copyright notice and this
permission notice appear in all copies.
THE SOFTWARE IS PROVIDED “AS IS” AND ISC
DISCLAIMS ALL WARRANTIES WITH REGARD TO THIS
SOFTWARE INCLUDING ALL IMPLIED WARRANTIES OF
MERCHANTABILITY AND FITNESS.
IN NO EVENT SHALL ISC BE LIABLE FOR ANY SPECIAL,
DIRECT, INDIRECT, OR CONSEQUENTIAL DAMAGES OR
ANY DAMAGES WHATSOEVER RESULTING FROM LOSS
OF USE, DATA OR PROFITS, WHETHER IN AN ACTION OF
CONTRACT, NEGLIGENCE OR OTHER TORTIOUS ACTION,
ARISING OUT OF OR IN CONNECTION WITH THE USE OR
PERFORMANCE OF THIS SOFTWARE.
Internet Systems Consortium, Inc.
950 Charter Street Redwood City, CA 94063
<info@isc.org> http://www.isc.org/
nExhibit-O
OpenBSD: telnet.c,v 1.6 1998/07/27 15:29:29 millert Exp
NetBSD: telnet.c,v 1.7 1996/02/28 21:04:15 thorpej Exp
Copyright (c) 1988, 1990, 1993
The Regents of the University of California. All rights
reserved.
Redistribution and use in source and binary forms, with
or without modification, are permitted provided that the
following conditions are met:
1. Redistributions of source code must retain the
above copyright notice, this list of conditions and the
following disclaimer.
2. Redistributions in binary form must reproduce the
above copyright notice, this list of conditions and the
following disclaimer in the documentation and/or other
materials provided with the distribution.
3. All advertising materials mentioning features or
use of this software must display the following
acknowledgement:
This product includes software developed by the
University of California, Berkeley and its contributors.
4. Neither the name of the University nor the names of
its contributors may be used to endorse or promote
products derived from this software without specific
prior written permission.
THIS SOFTWARE IS PROVIDED BY THE REGENTS AND
CONTRIBUTORS “AS IS” AND ANY EXPRESS OR IMPLIED
WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE
IMPLIED WARRANTIES OF MERCHANTABILITY AND
FITNESS FOR A PARTICULAR PURPOSE ARE DISCLAIMED.
IN NO EVENT SHALL THE REGENTS OR CONTRIBUTORS
BE LIABLE FOR ANY DIRECT, INDIRECT, INCIDENTAL,
SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES
(INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF
SUBSTITUTE GOODS OR SERVICES; LOSS OF USE, DATA,
OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER
CAUSED AND ON ANY THEORY OF LIABILITY, WHETHER
IN CONTRACT, STRICT LIABILITY, OR TORT (INCLUDING
NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY
OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED
OF THE POSSIBILITY OF SUCH DAMAGE.
nExhibit-P
ORIGINAL LICENSE:
This software is
(c) Copyright 1992 by Panagiotis Tsirigotis
The author (Panagiotis Tsirigotis) grants permission to use,
copy, and distribute this software and its documentation
for any purpose and without fee, provided that the
above copyright notice extant in files in this distribution
is not removed from files included in any redistribution
and that this copyright notice is also included in any
redistribution.
Modifications to this software may be distributed, either
by distributing the modified software or by distributing
patches to the original software, under the following
additional terms:
1. The version number will be modified as follows:
a. The first 3 components of the version number
(i.e <number>.<number>.<number>) will remain
unchanged.
b.A new component will be appended to the version
number to indicate the modification level. The
form of this component is up to the author of the
modifications.
2. The author of the modifications will include his/her
name by appending it along with the new version
number to this file and will be responsible for any
wrong behavior of the modified software.
The author makes no representations about the suitability
of this software for any purpose. It is provided “as is”
without any express or implied warranty.
Modifications:
Version: 2.1.8.7-current
Copyright 1998-2001 by Rob Braun
Sensor Addition
Version: 2.1.8.9pre14a
Copyright 2001 by Steve Grubb
This is an exerpt from an email I recieved from the original
author, allowing xinetd as maintained by me, to use the
higher version numbers:
I appreciate your maintaining the version string guidelines
as specified in the copyright. But I did not mean them to
last as long as they did.
So, if you want, you may use any 2.N.* (N >= 3) version
string for future xinetd versions that you release. Note that
I am excluding the 2.2.* line; using that would only create
confusion. Naming the next release 2.3.0 would put to
rest the confusion about 2.2.1 and 2.1.8.*.
nExhibit-Q
Except where otherwise noted in the source code (e.g.
the files hash.c, list.c and the trio files, which are covered
by a similar licence but with different Copyright notices)
all the files are:
Copyright (C) 1998-2003 Daniel Veillard.
All Rights
Reserved.
Permission is hereby granted, free of charge, to any
person obtaining a copy of this software and associated
documentation files (the “Software”), to deal in the
Software without restriction, including without limitation
the rights to use, copy, modify, merge, publish, distribute,
sublicense, and/or sell copies of the Software, and to
permit persons to whom the Software is furnished to do
so, subject to the following conditions:
The above copyright notice and this permission notice
shall be included in all copies or substantial portions of
the Software.
LICENSE
8
THE SOFTWARE IS PROVIDED “AS IS”, WITHOUT
WARRANTY OF ANY KIND, EXPRESS OR IMPLIED,
INCLUDING BUT NOT LIMITED TO THE WARRANTIES
OF MERCHANTABILITY, FITNESS FOR A PARTICULAR
PURPOSE AND NONINFRINGEMENT. IN NO EVENT
SHALL THE DANIEL VEILLARD BE LIABLE FOR ANY
CLAIM, DAMAGES OR OTHER LIABILITY, WHETHER
IN AN ACTION OF CONTRACT, TORT OR OTHERWISE,
ARISING FROM, OUT OF OR IN CONNECTION WITH THE
SOFTWARE OR THE USE OR OTHER DEALINGS IN THE
SOFTWARE.
Except as contained in this notice, the name of Daniel
Veillard shall not be used in advertising or otherwise to
promote the sale, use or other dealings in this Software
without prior written authorization from him.
nExhibit-R
LICENSE ISSUES
The OpenSSL toolkit stays under a dual license, i.e. both
the conditions of the OpenSSL License and the original
SSLeay license apply to the toolkit.
See below for the actual license texts. Actually both
licenses are BSD-style Open Source licenses. In case of
any license issues related to OpenSSL please contact
openssl-core@openssl.org.
OpenSSL License
Copyright (c) 1998-2004 The OpenSSL Project. All rights
reserved.
Redistribution and use in source and binary forms, with
or without modification, are permitted provided that the
following conditions are met:
1. Redistributions of source code must retain the
above copyright notice, this list of conditions and the
following disclaimer.
2. Redistributions in binary form must reproduce the
above copyright notice, this list of conditions and the
following disclaimer in the documentation and/or other
materials provided with the distribution.
3. All advertising materials mentioning features or
use of this software must display the following
acknowledgment:
“This product includes software developed by the
OpenSSL Project for use in the OpenSSL Toolkit.
(http://www.openssl.org/)”
4. The names “OpenSSL Toolkit” and “OpenSSL Project”
must not be used to endorse or promote products
derived from this software without prior written
permission. For written permission, please contact
openssl-core@openssl.org.
5. Products derived from this software may not be called
“OpenSSL” nor may “OpenSSL” appear in their names
without prior written permission of the OpenSSL
Project.
6. Redistributions of any form whatsoever must retain
the following acknowledgment:
“This product includes software developed by the
OpenSSL Project for use in the OpenSSL Toolkit
(http://www.openssl.org/)”
THIS SOFTWARE IS PROVIDED BY THE OpenSSL
PROJECT “AS IS” AND ANY EXPRESSED OR IMPLIED
WARRANTIES, INCLUDING, BUT NOT LIMITED TO,
THE IMPLIED WARRANTIES OF MERCHANTABILITY
AND FITNESS FOR A PARTICULAR PURPOSE ARE
DISCLAIMED.
9
LICENSE
IN NO EVENT SHALL THE OpenSSL PROJECT OR
ITS CONTRIBUTORS BE LIABLE FOR ANY DIRECT,
INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR
CONSEQUENTIAL DAMAGES (INCLUDING, BUT NOT
LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS
OR SERVICES; LOSS OF USE, DATA, OR PROFITS; OR
BUSINESS INTERRUPTION) HOWEVER CAUSED AND ON
ANY THEORY OF LIABILITY, WHETHER IN CONTRACT,
STRICT LIABILITY, OR TORT (INCLUDING NEGLIGENCE
OR OTHERWISE) ARISING IN ANY WAY OUT OF THE
USE OF THIS SOFTWARE, EVEN IF ADVISED OF THE
POSSIBILITY OF SUCH DAMAGE.
This product includes cryptographic software written by
Eric Young (eay@cryptsoft.com). This product includes
software written by Tim Hudson (tjh@cryptsoft.com).
Original SSLeay License
Copyright (C) 1995-1998 Eric Young (eay@cryptsoft.com)
All rights reserved.
This package is an SSL implementation written by Eric
Young (eay@cryptsoft.com).
The implementation was written so as to conform with
Netscapes SSL.
This library is free for commercial and non-commercial
use as long as the following conditions are aheared to.
The following conditions apply to all code found in this
distribution, be it the RC4, RSA, lhash, DES, etc., code; not
just the SSL code. The SSL documentation included with
this distribution is covered by the same copyright terms
except that the holder is Tim Hudson (tjh@cryptsoft.com).
Copyright remains Eric Youngs, and as such any Copyright
notices in the code are not to be removed.
If this package is used in a product, Eric Young should be
given attribution as the author of the parts of the library
used.
This can be in the form of a textual message at program
startup or in documentation (online or textual) provided
with the package.
Redistribution and use in source and binary forms, with
or without modification, are permitted provided that the
following conditions are met:
1. Redistributions of source code must retain the
copyright notice, this list of conditions and the
following disclaimer.
2. Redistributions in binary form must reproduce the
above copyright notice, this list of conditions and the
following disclaimer in the documentation and/or other
materials provided with the distribution.
3. All advertising materials mentioning features or
use of this software must display the following
acknowledgement:
“This product includes cryptographic software written
by Eric Young (eay@cryptsoft.com)”
The word ‘cryptographic’ can be left out if the rouines
from the library being used are not cryptographic
related :-).
4. If you include any Windows specific code (or a
derivative thereof) from the apps directory (application
code) you must include an acknowledgement:
“This product includes software written by Tim Hudson
(tjh@cryptsoft.com)”
THIS SOFTWARE IS PROVIDED BY ERIC YOUNG “AS
IS” AND ANY EXPRESS OR IMPLIED WARRANTIES,
INCLUDING, BUT NOT LIMITED TO, THE IMPLIED
WARRANTIES OF MERCHANTABILITY AND FITNESS
FOR A PARTICULAR PURPOSE ARE DISCLAIMED. IN
NO EVENT SHALL THE AUTHOR OR CONTRIBUTORS
BE LIABLE FOR ANY DIRECT, INDIRECT, INCIDENTAL,
SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES
(INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF
SUBSTITUTE GOODS OR SERVICES; LOSS OF USE, DATA,
OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER
CAUSED AND ON ANY THEORY OF LIABILITY, WHETHER
IN CONTRACT, STRICT LIABILITY, OR TORT (INCLUDING
NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY
OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED
OF THE POSSIBILITY OF SUCH DAMAGE.
The licence and distribution terms for any publically
available version or derivative of this code cannot be
changed. i.e. this code cannot simply be copied and put
under another distribution licence [including the GNU
Public Licence.]
nExhibit-S
Copyright (c) 1998-2001,2002 Free Software Foundation,
Inc.
Permission is hereby granted, free of charge, to any
person obtaining a copy of this software and associated
documentation files (the “Software”), to deal in the Software
without restriction, including without limitation the rights
to use, copy, modify, merge, publish, distribute, distribute
with modifications, sublicense, and/or sell copies of the
Software, and to permit persons to whom the Software
is furnished to do so, subject to the following conditions:
The above copyright notice and this permission notice
shall be included in all copies or substantial portions of
the Software.
THE SOFTWARE IS PROVIDED “AS IS”, WITHOUT
WARRANTY OF ANY KIND, EXPRESS OR IMPLIED,
INCLUDING BUT NOT LIMITED TO THE WARRANTIES
OF MERCHANTABILITY, FITNESS FOR A PARTICULAR
PURPOSE AND NONINFRINGEMENT.
IN NO EVENT SHALL THE ABOVE COPYRIGHT HOLDERS
BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER
LIABILITY, WHETHER IN AN ACTION OF CONTRACT,
TORT OR OTHERWISE, ARISING FROM, OUT OF OR IN
CONNECTION WITH THE SOFTWARE OR THE USE OR
OTHER DEALINGS IN THE SOFTWARE.
Except as contained in this notice, the name(s) of the
above copyright holders shall not be used in advertising
or otherwise to promote the sale, use or other dealings in
this Software without prior written authorization.
nExhibit-T
Copyright (c) 1990 The Regents of the University of
California.
All rights reserved.
Redistribution and use in source and binary forms, with
or without modification, are permitted provided that the
following conditions are met:
1. Redistributions of source code must retain the
above copyright notice, this list of conditions and the
following disclaimer.
2. Redistributions in binary form must reproduce the
above copyright notice, this list of conditions and the
following disclaimer in the documentation and/or other
materials provided with the distribution.
3. All advertising materials mentioning features or
use of this software must display the following
acknowledgement:
This product includes software developed by the
University of California, Berkeley and its contributors.
4. Neither the name of the University nor the names of
its contributors may be used to endorse or promote
products derived from this software without specific
prior written permission.
THIS SOFTWARE IS PROVIDED BY THE REGENTS AND
CONTRIBUTORS “AS IS” AND ANY EXPRESS OR IMPLIED
WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE
IMPLIED WARRANTIES OF MERCHANTABILITY AND
FITNESS FOR A PARTICULAR PURPOSE ARE DISCLAIMED.
IN NO EVENT SHALL THE REGENTS OR CONTRIBUTORS
BE LIABLE FOR ANY DIRECT, INDIRECT, INCIDENTAL,
SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES
(INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF
SUBSTITUTE GOODS OR SERVICES; LOSS OF USE, DATA,
OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER
CAUSED AND ON ANY THEORY OF LIABILITY, WHETHER
IN CONTRACT, STRICT LIABILITY, OR TORT (INCLUDING
NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY
OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED
OF THE POSSIBILITY OF SUCH DAMAGE.
Copyright (C) 1985-2005 by the Massachusetts Institute
of Technology.
All rights reserved.
Export of this software from the United States of America
may require a specific license from the United States
Government. It is the responsibility of any person or
organization contemplating export to obtain such a license
before exporting.
WITHIN THAT CONSTRAINT, permission to use, copy,
modify, and distribute this software and its documentation
for any purpose and without fee is hereby granted, provided
that the above copyright notice appear in all copies and
that both that copyright notice and this permission notice
appear in supporting documentation, and that the name of
M.I.T. not be used in advertising or publicity pertaining to
distribution of the software without specific, written prior
permission. Furthermore if you modify this software you
must label your software as modified software and not
distribute it in such a fashion that it might be confused
with the original MIT software.
M.I.T. makes no representations about the suitability
of this software for any purpose. It is provided “as is”
without express or implied warranty.
THIS SOFTWARE IS PROVIDED “AS IS” AND WITHOUT
ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING,
WITHOUT LIMITATION, THE IMPLIED WARRANTIES OF
MERCHANTIBILITY AND FITNESS FOR A PARTICULAR
PURPOSE.
Individual source code files are copyright MIT, Cygnus
Support, OpenVision, Oracle, Sun Soft, FundsXpress, and
others.
Project Athena, Athena, Athena MUSE, Discuss,
Hesiod, Kerberos, Moira, and Zephyr are trademarks of
the Massachusetts Institute of Technology (MIT). No
commercial use of these trademarks may be made
without prior written permission of MIT.
“Commercial use” means use of a name in a product or
other for-profit manner. It does NOT prevent a commercial
firm from referring to the MIT trademarks in order to
convey information (although in doing so, recognition of
their trademark status should be given).
The following copyright and permission notice applies to
the OpenVision Kerberos Administration system located
in kadmin/create, kadmin/dbutil, kadmin/passwd, kadmin/
server, lib/kadm5, and portions of lib/rpc:
Copyright, OpenVision Technologies, Inc., 1996, All
Rights Reserved
WARNING: Retrieving the OpenVision Kerberos
Administration system source code, as described below,
indicates your acceptance of the following terms. If you
do not agree to the following terms, do not retrieve the
OpenVision Kerberos administration system.
You may freely use and distribute the Source Code
and Object Code compiled from it, with or without
modification, but this Source Code is provided to you
“AS IS” EXCLUSIVE OF ANY WARRANTY, INCLUDING,
WITHOUT LIMITATION, ANY WARRANTIES OF
MERCHANTABILITY OR FITNESS FOR A PARTICULAR
PURPOSE, OR ANY OTHER WARRANTY, WHETHER
EXPRESS OR IMPLIED. IN NO EVENT WILL OPENVISION
HAVE ANY LIABILITY FOR ANY LOST PROFITS, LOSS OF
DATA OR COSTS OF PROCUREMENT OF SUBSTITUTE
GOODS OR SERVICES, OR FOR ANY SPECIAL,
INDIRECT, OR CONSEQUENTIAL DAMAGES ARISING
OUT OF THIS AGREEMENT, INCLUDING, WITHOUT
LIMITATION, THOSE RESULTING FROM THE USE OF
THE SOURCE CODE, OR THE FAILURE OF THE SOURCE
CODE TO PERFORM, OR FOR ANY OTHER REASON.
OpenVision retains all copyrights in the donated Source
Code. OpenVision also retains copyright to derivative
works of the Source Code, whether created by
OpenVision or by a third party. The OpenVision copyright
notice must be preserved if derivative works are made
based on the donated Source Code.
OpenVision Technologies, Inc. has donated this
Kerberos Administration system to MIT for inclusion
in the standard Kerberos 5 distribution. This donation
underscores our commitment to continuing Kerberos
technology development and our gratitude for the
valuable work which has been performed by MIT and
the Kerberos community.
Portions contributed by Matt Crawford <crawdad@fnal.
gov> were work performed at Fermi National Accelerator
Laboratory, which is operated by Universities Research
Association, Inc., under contract DE-AC02-76CHO3000
with the U.S. Department of Energy.
The implementation of the Yarrow pseudo-random number
generator in src/lib/crypto/yarrow has the following
copyright:
Copyright 2000 by Zero-Knowledge Systems, Inc.
Permission to use, copy, modify, distribute, and sell this
software and its documentation for any purpose is hereby
granted without fee, provided that the above copyright
notice appear in all copies and that both that copyright
notice and this permission notice appear in supporting
documentation, and that the name of Zero-Knowledge
Systems, Inc. not be used in advertising or publicity
pertaining to distribution of the software without specific,
written prior permission. Zero-Knowledge Systems, Inc.
makes no representations about the suitability of this
software for any purpose. It is provided “as is” without
express or implied warranty.
ZERO-KNOWLEDGE SYSTEMS, INC. DISCLAIMS ALL
WARRANTIES WITH REGARD TO THIS SOFTWARE,
INCLUDING
ALL
IMPLIED
WARRANTIES
OF
MERCHANTABILITY AND FITNESS, IN NO EVENT SHALL
ZERO-KNOWLEDGE SYSTEMS, INC. BE LIABLE FOR ANY
SPECIAL, INDIRECT OR CONSEQUENTIAL DAMAGES OR
ANY DAMAGES WHATSOEVER RESULTING FROM LOSS
OF USE, DATA OR PROFITS, WHETHER IN AN ACTION
OF CONTRACT, NEGLIGENCE OR OTHER TORTUOUS
ACTION, ARISING OUT OF OR IN CONNECTION WITH
THE USE OR PERFORMANCE OF THIS SOFTWARE.
The implementation of the AES encryption algorithm in
src/lib/crypto/aes has the following copyright:
Copyright (c) 2001, Dr Brian Gladman <brg@gladman.
uk.net>, Worcester, UK.
All rights reserved.
LICENSE TERMS
The free distribution and use of this software in both
source and binary form is allowed (with or without
changes) provided that:
1. distributions of this source code include the above
copyright notice, this list of conditions and the
following disclaimer;
2. distributions in binary form include the above
copyright notice, this list of conditions and the
following disclaimer in the documentation and/or
other associated materials;
3. the copyright holder’s name is not used to endorse
products built using this software without specific
written permission.
DISCLAIMER
This software is provided “as is” with no explcit or implied
warranties in respect of any properties, including, but not
limited to, correctness and fitness for purpose.
The implementation of the RPCSEC_GSS authentication
flavor in src/lib/rpc has the following copyright:
Copyright (c) 2000 The Regents of the University of
Michigan.
All rights reserved.
Copyright (c) 2000 Dug Song <dugsong@UMICH.EDU>.
All rights reserved, all wrongs reversed.
Redistribution and use in source and binary forms, with
or without modification, are permitted provided that the
following conditions are met:
1. Redistributions of source code must retain the
above copyright notice, this list of conditions and the
following disclaimer.
2. Redistributions in binary form must reproduce the
above copyright notice, this list of conditions and the
following disclaimer in the documentation and/or other
materials provided with the distribution.
3. Neither the name of the University nor the names of
its contributors may be used to endorse or promote
products derived from this software without specific
prior written permission.
THIS SOFTWARE IS PROVIDED “AS IS” AND ANY
EXPRESS OR IMPLIED WARRANTIES, INCLUDING,
BUT NOT LIMITED TO, THE IMPLIED WARRANTIES OF
MERCHANTABILITY AND FITNESS FOR A PARTICULAR
PURPOSE ARE DISCLAIMED. IN NO EVENT SHALL THE
REGENTS OR CONTRIBUTORS BE LIABLE FOR ANY
DIRECT, INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY,
OR CONSEQUENTIAL DAMAGES (INCLUDING, BUT NOT
LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS
OR SERVICES; LOSS OF USE, DATA, OR PROFITS; OR
BUSINESS INTERRUPTION) HOWEVER CAUSED AND ON
ANY THEORY OF LIABILITY, WHETHER IN CONTRACT,
STRICT LIABILITY, OR TORT (INCLUDING NEGLIGENCE
OR OTHERWISE) ARISING IN ANY WAY OUT OF THE
USE OF THIS SOFTWARE, EVEN IF ADVISED OF THE
POSSIBILITY OF SUCH DAMAGE.
Acknowledgments
Appreciation Time!!!! There are far too many people to
try to thank them all; many people have contributed to
the development of Kerberos V5. This is only a partial
listing....
Thanks to Kevin Coffman and the CITI group at the
University of Michigan for providing patches for
implementing RPCSEC_GSS authentication in the RPC
library.
Thanks to Derrick Schommer for reporting multiple
memory leaks.
Thanks to Quanah Gibson-Mount of Stanford University
for helping exercise the thread support code.
Thanks to Michael Tautschnig for reporting the heap buffer
overflow inthe password history mechanism. [MITKRB5SA-2004-004]
Thanks to Wyllys Ingersoll for finding a buffer-size problem
in theRPCSEC_GSS implementation.
Thanks to the members of the Kerberos V5 development
team at MIT, both past and present: Danilo Almeida, Jeffrey
Altman, Jay Berkenbilt, Richard Basch, Mitch Berger, John
Carr, Don Davis, Alexandra Ellwood, Nancy Gilman, Matt
Hancher, Sam Hartman, Paul Hill, Marc Horowitz, Eva
Jacobus, Miroslav Jurisic, Barry Jaspan, Geoffrey King,
John Kohl, Peter Litwack, Scott McGuire, Kevin Mitchell,
Cliff Neuman, Paul Park, Ezra Peisach, Chris Provenzano,
Ken Raeburn, Jon Rochlis, Jeff Schiller, Jen Selby, Brad
Thompson, Harry Tsai, Ted Ts’o, Marshall Vale, Tom Yu.
Very special thanks go to Marshall Vale, our departing
team leader.
Over the past few years, Marshall has been extremely
valuable to us as mentor, advisor, manager, and friend.
Marshall’s devotion as a champion of Kerberos has helped
our team immensely through many trials and hardships.
We will miss him tremendously, and we wish him the best
in his future endeavors.
nExhibit-U
Copyright (c) 1989 The Regents of the University of
California.
All rights reserved.
This code is derived from software contributed to Berkeley
by Mike Muuss.
Redistribution and use in source and binary forms, with
or without modification, are permitted provided that the
following conditions are met:
1. Redistributions of source code must retain the
above copyright notice, this list of conditions and the
following disclaimer.
2. Redistributions in binary form must reproduce the
above copyright notice, this list of conditions and the
following disclaimer in the documentation and/or other
materials provided with the distribution.
3. All advertising materials mentioning features or
use of this software must display the following
acknowledgement:
This product includes software developed by the
University of California, Berkeley and its contributors.
4. Neither the name of the University nor the names of
its contributors may be used to endorse or promote
products derived from this software without specific
prior written permission.
THIS SOFTWARE IS PROVIDED BY THE REGENTS AND
CONTRIBUTORS “AS IS” AND ANY EXPRESS OR IMPLIED
WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE
IMPLIED WARRANTIES OF MERCHANTABILITY AND
FITNESS FOR A PARTICULAR PURPOSE ARE DISCLAIMED.
IN NO EVENT SHALL THE REGENTS OR CONTRIBUTORS
BE LIABLE FOR ANY DIRECT, INDIRECT, INCIDENTAL,
SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES
(INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF
SUBSTITUTE GOODS OR SERVICES; LOSS OF USE, DATA,
OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER
CAUSED AND ON ANY THEORY OF LIABILITY, WHETHER
IN CONTRACT, STRICT LIABILITY, OR TORT (INCLUDING
NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY
OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED
OF THE POSSIBILITY OF SUCH DAMAGE.
License Information for the Software
Used in the Unit
About GPL (GNU-General Public
License), LGPL (GNU Lesser General
Public License) License
This product uses GPL/LGPL software and software
made by other companies.
After you purchase this product, you may procure,
modify or distribute the source code of the GPL/
LGPL software that is used in the product.
MARANTZ provides the source code based on the
GPL and LPGL licenses at the actual cost upon your
request to our customer service center. However,
note that we make no guarantees concerning the
source code. Please also understand that we do
not offer support for the contents of the source
code.
LICENSE
10
www.marantz.com
You can find your nearest authorized distributor or dealer on our website.
is a registered trademark.
Printed in China
12/2009 541110297226M
Download PDF
Similar pages