Pre-lnstallation
Frigidaire
Electrical
Requirements ................................
2
Requirements ........................................
2
Exhaust System Requirements ............................
3-4
Gas Supply Requirements .....................................
Location of Your Dryer ..........................................
4
4-5
Mobile Home Installation .......................................
Installation
Instructions
Rough-In Dimensions ..........................................
Dryer
6-7
Unpacking ...........................................................
7
Reversing
7
Electrical
Gas &
Electric
6
Door Swing ...........................................
Installation .............................................
8
Grounding Requirements .......................................
8
Electrical Connections--3-wire
..............................
9
Electrical Connections_-wire
..............................
9
Gas Connection ...................................................
10
General Installation ..............................................
10
Replacement
10
Parts ..............................................
Before beginning installation, carefully read these instructions. This will simplify the installation and ensure
the dryer is installed correctly and safely. Leave these instructions near the Dryer after installation for future
reference.
NOTE: The electrical service to the Dryer must conform with local codes and ordinances and the latest edition of the
National Electrical Code, ANSI/NFPA 70.
NOTE: The gas service to the Dryer must conform with local codes and ordinances and the latest edition of the
National Fuel Gas Code ANSI Z223.1.
NOTE: The Dryer is designed under ANSI Z 21.5.1 or ANSI/UL 2158 - CAN/CSA C22.2 (latest editions) for HOME
USE only. This Dryer is not recommended for commercial applications such as restaurants or beauty salons, etc.
Save These Instructions
www.ftigidaire.r.om
1
P/N 134306200 (0310)
POWER SUPPLY - 3 wire or 4-wire, 240 volt, single phase,
60 Hz, Alternating Current.
For your safety the information in
this manual must be followed to minimize the
POWER SUPPLY CORD KIT - The dryer MUST employ a
3-conductor power supply cord NEMA 10-30 type SRDT
rated at 240 volt AC minimum, 30 amp., with 3 open end
spade lug connectors with upturned ends or closed loop
connectors OR a 4-conductor power supply cord NEMA
14-30 type SRDT or ST (as required) rated at 240 volt AC
minimum, 30 amp., with 4 open end spade lug connectors
with upturned ends or closed loop connectors and marked
for use with clothes dryers, tf being installed in a
manufactured
(mobile) home, the dryer MUST employ a
4-conductor power supply cord NEMA 14-30 type SRDT or
ST (as required) rated at 240 volt AC minimum, 30 amp.,
with 4 open end spade lug connectors with upturned ends
or closed loop connectors and marked for use with clothes
dryers. See ELECTRICAL CONNECTIONS for additional
instructions.
risk of fire or explosion or to prevent property
damage, personal injury or loss of life.
- Do not store or use gasoline or other
flammable vapors and liquid in the vicinity
this or any other appliance.
- WHATTO
DO IFYOU
SMELL
of
GAS
• Do not try to light any appliance.
• Do not touch any electrical switch; do not
use any phone in your building.
• Clear the room, building or area of all
occupants.
• Immediately call your gas supplier from a
neighbor's phone. Follow the gas supplier's
instructions.
• If you cannot reach your gas supplier,
the fire department.
OUTLET RECEPTACLE - NEMA 10-30R (3-wire)
receptacle or NEMA 14-30R (4-wire) receptacle to be
located so the power supply cord is accessible when the
dryer is in the installed position.
call
Installation and service must be performed by a
qualified installer, service agency or the gas
supplier.
PRE-INSTALLATION
NEMA 10-30R
REQUIREMENTS
Tools and Materials Required for Installation:
1. Phillips head screwdriver.
2. Channel-lock adjustable pliers.
3. Carpenter's level.
4. Flat or straight blade screwdriver.
5. Duct tape.
6. Rigid or flexible metal 4 inch (10.2 cm) duct.
7. Vent hood.
8. Pipe thread sealer (Gas).
9. Plastic knife.
I
NEMA 14-30R
GAS Dryer
I
CIRCUIT - Individual 15 amp. branch circuit fused with a 15
amp. maximum time delay fuse or circuit breaker.
POWER SUPPLY - 3 wire, 120 volt single phase, 60 Hz,
Alternating Current.
POWER SUPPLY CORD - The dryer is equipped with a 120
volt 3-wire power cord.
ELECTRICAL
I
REQUIREMENTS
ELECTRIC
Dryer
NOTE: Do not under
I
any circumstances
remove grounding
prong from plug.
CIRCUIT - Individual 30 amp. branch circuit fused with 30
amp. minimum time delay fuses or circuit breakers.
GROUNDING PRONG
2
Printed in U.S.A.
EXHAUST
SYSTEM
REQUIREMENTS
Use only 4 inch (10.2 cm) diameter (minimum) rigid or
flexible metal duct and approved vent hood which has a
swing-out damper(s) that open when the dryer is in
operation. When the dryer stops, the dampers automatically
close to prevent drafts and the entrance of insects and
rodents. To avoid restricting the outlet, maintain a minimum
of 12 inches (30.5 cm) clearance between the vent hood
and the ground or any other obstruction.
The following are specific requirements
for proper and safe operation of your dryer. Failure to
follow these instructions can create excessive drying
times and fire hazards.
MAXIMUM
VENT HOOD TYPE
(Preferred)
Number
of
90 °
Turns
[] If the dryer is not exhausted outdoors, some fine
lint will be expelled into the laundry area. An
accumulation of lint in any area of the home can create a
health and fire hazard. The dryer exhaust system MUST
be exhausted to the outside of the dwelling!
[] Do not allow combustible materials (for example:
clothing, draperies/curtains,
paper) to come in contact
with exhaust system. The dryer MUST NOT be exhausted
into a chimney, a wall, a ceiling, or any concealed space of
a building which can accumulate lint, resulting in a fire
hazard.
_4'_
_Louvered
(10.2 cm)
(6.35 cm)
0
60ft.
(18.28
m)
1
52ft.
(15.84
2
44ft.
(13.41
3
32 ft.
4
28 ft.
48 ft.(14.63
m)
m)
40 ft.(12.19
m)
m)
32 ft.
(9.75
m)
24ft. (7.31 m)
(8.53
m)
16ft.
MAXIMUM
[] Do not use plastic flexible duct to exhaust the dryer.
Excessive lint can build up inside exhaust system and
create a fire hazard and restrict air flow. Restricted air flow
will increase dryer times. If your present system is made up
of plastic duct or metal foil duct, replace it with a rigid or
flexible metal duct. Ensure the present duct is free of any
lint prior to installing dryer duct.
LENGTH
of 4" (10.2 cm) Dia. Rigid Metal Duct
(9.75 m)
(4.87 m)
LENGTH
of 4" (10.2 cm) Dia. Flexible Metal Duct
VENT HOOD TYPE
(Preferred)
Number
of
90 °
Turns
Louvered
(6.36cm)
(10.2 cm)
o
30ft.
(9.14
m)
18 ft. (5.49 m)
1
22 ft.
(6.71
m)
14 ft. (4.27 m)
2
14 ft.
(4.27 m)
10 ft. (3.05
NOT RECOMMENDED
3
m)
[] Exceeding the length of duct pipe or number of
elbows allowed in the "MAXIMUM LENGTH" charts can
cause an accumulation of lint in the exhaust system.
Plugging the system could create a fire hazard, as well as
increase drying times.
[] Do not screen the exhaust ends of the vent system,
nor use any screws or rivets to assemble the exhaust
system. Lint can become caught in the screen, on the
screws or rivets, clogging the duct work and creating a fire
hazard as well as increasing drying times. Use an approved
vent hood to terminate the duct outdoors, and seal all joints
with duct tape. All male duct pipe fittings MUST be installed
downstream with the flow of air.
Explosion hazard. Do not install the dryer
where gasoline or other flammables are kept or stored.
If the dryer is installed in a garage, it must be a minimum of
18 inches (45.7 cm) above the floor. Failure to do so can
result in death, explosion, fire or burns.
INSTALL MALE FITTINGS
IN CORRECT
DIRECTION
In installations where the exhaust system is not described
in the charts, the following method must be used to
determine if the exhaust system is acceptable:
1. Connect an inclined or digital manometer between the
dryer and the point the exhaust connects to the dryer.
2. Set the dryer timer and temperature to air fluff (cool
down) and start the dryer.
3. Read the measurement on the manometer.
4. The system back pressure MUST NOT be higher than
0.75 inches of water column. If the system back
pressure is less than 0.75 inches of water column, the
system is acceptable. If the manometer reading is
higher than 0.75 inches of water column, the system is
too restrictive and the installation is unacceptable.
Althoughverticalorientation
oftheexhaustsystemis
acceptable,
certainextenuating
circumstances
couldaffect
theperformance
ofthedryer:
• Onlytherigidmetalductworkshouldbeused.
• Ventingverticalthrougha roofmayexposetheexhaust
systemtodowndraftscausinganincreasein vent
restriction.
• Running
theexhaustsystemthroughanuninsulated
areamaycausecondensation
andfasteraccumulation
oflint.
• Compression
orcrimpingoftheexhaustsystemwill
causeanincreaseinventrestriction.
Theexhaustsystemshouldbeinspected
andcleaneda
minimum
ofevery18months with normal usage. The more
the dryer is used, the more often you should check the
exhaust system and vent hood for proper operation.
EXHAUST DIRECTION
All dryers shipped from the factory are set up for rear
exhausting. However, on electric dryers, exhausting can be
to the right or left side of the cabinet or the bottom of the
dryer. On gas dryers, exhausting can be to the right side of
the cabinet or the bottom of the dryer. Directional
exhausting can be accomplished by installing Exhaust Kit,
P/N 131456800, available through your parts distributor.
Follow the instructions supplied with the kit.
LOCATION
DRYER
INSTALLATION IN RECESS OR CLOSET
1. A dryer installed in a bedroom, bathroom, recess or
closet, MUST be exhausted outdoors.
2. No other fuel burning appliance shall be installed in the
same closet as the Gas dryer.
3. Your dryer needs the space around it for proper
ventilation.
SAME AS OTHER SIDE
DO NOT install your dryer in a closet with a solid door.
(34 cm)
GAS SUPPLY
OF YOUR
DO NOT INSTALLYOUR DRYER:
1. In an area exposed to dripping water or outside weather
conditions.
2. In an area where it will come in contact with curtains,
drapes, or anything that will obstruct the flow of
combustion and ventilation air.
3. On carpet. Floor MUST be solid with a maximum slope
of 1 inch (2.54 cm).
EXHAUST DUCT LOCATING DIMENSIONS
._,j!
2. The gas supply line should be of 1/2 inch (1.27 cm)
pipe.
3. If codes allow, flexible metal tubing may be used to
connect your dryer to the gas supply line. The tubing
MUST be constructed of stainless steel or plasticcoated brass.
4. The gas supply line MUST have an individual shutoff
valve.
5. A 1/8 inch (0.32 cm) N.P.T. plugged tapping, accessible
for test gauge connection, MUST be installed
immediately upstream of the gas supply connection to
the dryer.
6. The dryer MUST be disconnected from the gas supply
piping system during any pressure testing of the gas
supply piping system at test pressures in excess of 1/2
psig (3.45 kPa).
7. The dryer MUST be isolated from the gas supply piping
system during any pressure testing of the gas supply
piping system at test pressures equal to or less than
1/2 psig (3.45 kPa).
4. A minimum of 120 square inches (774.2 square cm) of
opening, equally divided at the top and bottom of the
door, is required. Air openings are required to be
unobstructed when a door is installed. A Iouvered door
with equivalent air openings for the full length of the door
is acceptable.
REQUIREMENTS
Replace copper connecting pipe that is
not plastic-coated. Stainless steel or plastic-coated
brass MUST be used.
1. Installation MUST conform with local codes, or in the
absence of local codes, with the National Fuel Gas
Code, ANSI Z223.1 (latest edition).
4
MINIMUM INSTALLATION CLEARANCES
Alcove
Closet
SIDES
0 (0 cm)
0(0cm)
- Inches (cm)
REAR
TOP
FRONT
0 (0 cm) 15 (38.1 cm)
0(0cm)
15(38.1cm)
1(2.54cm)
60 sq. inches
87.1 sq. cm)
Closet door ventilation required: 2 (ouvered openings each
60 square inches (387 square centimeters) -- 3 inches (7.6
cm) from bottom and top of door.
NOTE: Under counter and stack models - 0 inches (0 cm)
for sides, rear, and top.
Iii08_ .q4inches
sq. cm)
This dryer MUST be exhausted outdoors.
5. The following illustrations show minimum clearance
dimensions for proper operation in a recess or closet
installation.
CLOSET
DOOR
ii
_(("_ 0" (0 cm)
ii
_(_
1" (2.54 cm)
,,
_(;',_0"(0 cm)
1" (2.54 cm)
I
0" (0 cm)
MOBILE
1.
Dryer
MUST
the mobile
HOME
INSTALLATION
be exhausted
home)
using
outside
(outdoors,
metal ducting
UNDER
COUNTER
& STACK
ROUGH-IN
not beneath
MODELS
DIMENSIONS
that will not support
combustion.
Metal ducting must be 4 inches (10.16 cm) in
diameter
with no obstructions.
Rigid metal duct is preferred.
2.
If dryer
is exhausted
through
the floor and area beneath
(68.3 cm)
the
mobile home is enclosed,
the exhaust system MUST
terminate
outside the enclosure
with the termination
securely fastened
to the mobile home structure.
When installing
a gas dryer into a mobile home,
3.
must be made
for outside
be not less than twice
MUST
5.
6.
requirements.
installation
MUST
& Safety
Standard
Mobile
is to
Installation
Kit No. 346764 is available from your dealer.
Refer to pages 2 and 3 for other important
venting
to current
B
ELECTRIC
CONNECTION
Home
Manufactured
(which
2 9116'_
(6.5 cm)
Home
is a Federal
Regulation
Title 24 CFR-Part
32-80) or when such
is not applicable,
with American
National Standard
Mobile Homes.
,=F----13 1/2" --_
standard
for
(34.4 cm)
The dryer
ANSI/UL2158
- CAN/CSA
is designed
C22.2
under
(latest
ANSI
editions)
Z 21.5.1
I
O
or
for HOME
USE only.
/
_i
outlet.
This dryer
conform
to the floor.
exhaust
4.
Construction
be fastened
26 7/8"
a provision
make up air. This provision
the area of the dryer
i
35 1/4"
(89.5
3/8" (0.96
/
33/4'
cm) Dia.
GAS PIPE
1' (2.54 cm)
(9.5 cm)
ii
cm)
REAR VIEW
DO
DON'T
©
I
Correct
47 1/2"
(120.7 cm)
Incorrect
21/4"
L
/
(5.7 cm)
LDOOR OPEN 900
ii
DO
©
Correct
B
Incorrect
4 3/8"
(11.1 cm) --_
/
OPTIONAL
VENT KNOCKOUT_
DON'T_
27'
(68.6 cm)
©
©
SIDE VIEW
I Correc t
Ii
Incorrect
6
3 3/4"
(9.5 cm)
TOP CONSOLE MODELS
ROUGH-IN DIMENSIONS
UNPACKING
1.
Using
the four shipping
side), carefully
shipping
carton
lay the dryer
corner
posts
(two on each
on its left side and remove
foam
base.
26 7/8'
To prevent
(68.3 cm)
as a means
NOTE:
On under
panel
2.
[_}" ELECTRIC CONNECTION
Return
damage,
do not use the control
panel
to pick up or move the dryer.
counter
model
may be removed
the dryer
clothes
dryers,
the top
for installation.
to an upright
position.
43 5/8"
cm)
j_/PAD
.
36"
(91.5 cm)
i
©
3/8" (0.96
33/4"
(9.5 cm)
REVERSING
cm) Dia.
GAS PIPE
1' (2.54 cm)
Your dryer
is designed
any time without
REAR VIEW
by transferring
so the door swing
additional
hinges
DOOR SWING
parts.
may be reversed
Conversion
to the opposite
at
is accomplished
side of the cabinet.
To change the direction of the door opening:
1.
Open the dryer
door.
Remove
the four hinge
the left side of the door opening.
installation.
471/2"
(120.7 cm)
NOTE: You may need a plastic
out the plugs.
v
2.
Remove
Be careful
the four screws
dryer front
panel (see
not to scratch
that secure
below).
from each of the two hinges
removing
3.
Rotate
dryer
DOOR OPEN 90 o
4.
Install
hole plugs
Place nearby
NOTE:
from
for future
knife
to help pull
the paint.
the door hinges
Remove
to the
one screw
first. Hold the door firmly
before
the last two screws.
the door
180 ° and reinstall
the door hinges
to the
front panel with the four screws.
the four hinge
the right side
hole plugs
in the open
screw
holes
of the door opening.
4 3/8"
(11.1 cm) ---_
OPTIONAL
VENT
KNOCKOUT_.
_
•
w--
--SIDE VIEW
27'
(68.6 cm)
REMOVE 4 SCREWS
3 3/4"
(9.5 cm)
(ONE FROM EACH
HINGE FIRST)
on
ELECTRICAL
J
INSTALLATION
ELECTRIC
Dryer
J
The following are specific requirements
for proper and safe electrical installation of your dryer.
Failure to follow these instructions can create electrical
shock and/or a fire hazard.
For a permanently connected dryer:
1. The dryer MUST be connected to a grounded metal,
permanent wiring system; or an equipment grounding
conductor must be run with the circuit conductors and
connected to the equipment-grounding terminal or lead
on the appliance.
[] This appliance MUST be properly grounded.
Electrical shock can result if the dryer is not properly
grounded. Follow the instructions in this manual for proper
grounding.
[] Do not use an extension cord with this dryer. Some
extension cords are not designed to withstand the amounts
of electrical current this dryer utilizes and can melt, creating
electrical shock and/or fire hazard. Locate the dryer within
reach of the receptacle for the length power cord to be
purchased, allowing some slack in the cord. Refer to the
pre-installation requirements in this manual for the proper
power cord to be purchased.
GAS Dryer
This dryer is equipped with a three-prong (grounding) plug
for your protection against shock hazard and should be
plugged directly into a properly grounded three-prong
receptacle. Do not cut or remove the grounding prong from
this plug.
[] A U.L. approved strain relief must be installed onto
power cord. If the strain relief is not attached, the cord can
be pulled out of the dryer and can be cut by any movement
of the cord, resulting in electrical shock.
[] Do not use an aluminum wired receptacle with a
copper wired power cord and plug (or vice versa). A
chemical reaction occurs between copper and aluminum
and can cause electrical shorts. The proper wiring and
receptacle is a copper wired power cord with a copper
wired receptacle.
NOTE: Dryers operating on 208 volt power supply will have
longer drying times than operating on 240 volt power supply.
GROUNDING
J
REQUIREMENTS
ELECTRIC
Dryer
_
Improper connection of the equipment
grounding conductor can result in a risk of electrical shock.
Check with a licensed electrician if you are in doubt as to
whether the appliance is properly grounded.
For a grounded, cord-connected dryer:
1. The dryer MUST be grounded. In the event of a
malfunction or breakdown, grounding will reduce the risk
of electrical shock by a path of least resistance for
electrical current.
2. If your dryer is equipped with a power supply cord having
an equipment-grounding conductor and a grounding plug,
the plug MUST be plugged into an appropriate, copper
wired receptacle that is properly installed and grounded
in accordance with all local codes and ordinances. If in
doubt, call a licensed electrician.
J
J
GREEN
SCREW
GROUND
SCREW
SILVER TERMINAL
GREEN
NE_
GROUNDi
WIRE
GREEN POWER
GROUND WIRE
CORD
SILVER TERMINAL
TERMINAL
GREEN
TIGHTEN
NUT
TO THESE
THREADS
GROUND
WIRE
JUT
TIGHTEN NUT
TO THESE
THREADS
BLOCK
NUT
RELIEF
BRACKET
POWER
CORD
BRACKET
POWER
ELECTRICAL
CONNECTIONS
FOR 4-WIRE SYSTEM
CORD
1
ELECTRICAL
CONNECTIONS
FOR 3-WIRE SYSTEM
I
ELECTRIC
Dryer
ELECTRIC
Dryer
I
1. Remove the screws securing the terminal block access
cover and the strain relief mounting bracket located on
the back of the dryer upper corner.
I
.
1. Remove the screws securing the terminal block access
cover and the strain relief mounting bracket located on
the back of the dryer upper corner.
.
2. Install a U.L. approved strain relief into the power cord
entry hole of the mounting bracket. Finger tighten the nut
only at this time.
Install a U.L. approved strain relief in the entry hole of
the mounting bracket. Finger tighten the nut only at this
time.
Remove the green neutral ground wire from the green
ground screw located above the terminal block.
(_
CONDUCTOR
TYPICAL 4
,WHITE
£
3. Thread a U.L. approved 30 amp. power cord, NEMA
10-30 type SRDT, through the strain relief.
BLACK
TYPICAL 4
CONDUCTOR
RED 240V
""_*'
_"-GREEN
30 AMP NEMA 14-30 TYPE SRDT OR ST
4. Attach the power cord neutral (center wire) conductor to
the silver colored center terminal on the terminal block.
Tighten the screw securely.
4. Thread a U.L. approved 30 amp power cord, NEMA 14-30
type ST or SRDT through the strain relief.
5. Attach the remaining two power cord outer conductors to
the outer brass colored terminals on the terminal block.
Tighten both screws securely.
5. Attach the green power cord ground wire to the cabinet
with the green ground screw.
Do not make a sharp bend or crimp wiring/
conductor at connections.
6. Attach the white (neutral) power cord conductor from the
power cord and the green ground wire from the dryer
harness to the silver-colored center terminal on the
terminal block. Tighten the screw securely.
6. Reattach the strain relief mounting bracket to the back of
the dryer with two screws. Tighten screws securely.
7. Attach the red and black power cord conductors to the
outer brass-colored terminals on the terminal block.
7. Tighten the screws securing the cord restraint firmly
against the power cord.
Do not make a sharp bend or crimp wiring/
conductor at the connections.
8. Tighten the strain relief nut securely so that the strain
relief does not turn.
8. Tighten the screws securing the cord restraint firmly
against the power cord.
9. Reinstall the terminal block cover.
9. Tighten the strain relief nut securely so the strain relief
does not turn.
10. Reinstall the terminal block access cover.
9
GAS CONNECTION
1. Remove the shipping cap from gas pipe at the rear of
the dryer.
5. Run the dryer through a cycle check for proper
operation.
NOTE: DO NOT connect the dryer to LP. gas service
without converting the gas valve. An L.R
conversion kit must be installed by a qualified gas
technician.
NOTE: On gas dryers, before the burner will light, it is
necessary for the gas line to be bled of air. If the
burner does not light within 45 seconds the first
time the dryer is turned on, the safety switch will
shut the burner off. tf this happens, turn the timer
to "OFF" and wait 5 minutes before making another
attempt to light.
2. Connect a 1/2 inch (1.27 cm) I.D. semi-rigid or approved
pipe from gas supply line to the 3/8 inch (0.96 cm) pipe
located on the back of the dryer (see pages 6 and 7).
Use a 1/2 inch to 3/8 inch (1.27 cm to 0.96 cm) reducer
for a connection. Apply an approved thread sealer that
is resistant to the corrosive action of liquefied gases on
all pipe connections.
6. If your dryer does not operate, please review the "Avoid
Service Checklist" located in your Use and Care Guide
before calling for service.
7. Place these instructions in a location near the dryer for
future reference.
3. Open the shutoff valve in the gas supply line to allow
gas to flow through pipe.
NOTE: Awiring diagram is located inside the dryer
console or under the top panel.
E OPEN / GAS FLOW POSITION
REPLACEMENT
PARTS
If replacement parts are needed for your dryer, contact
the source where you purchased the dryer.
4. Test all connections by brushing on a soapy water
solution. NEVER test for gas leaks with an open
flame.
GENERAL
Label all wires prior to disconnection when
servicing controls. Wiring errors can cause improper and
dangerous operation. Verify proper operation after servicing.
INSTALLATION
Destroy the carton and plastic bags after
the dryer is unpacked. Children might use them for play.
Cartons covered with rugs, bedspreads, or plastic sheets
can become airtight chambers causing suffocation. Place
all materials in a garbage container or make materials
inaccessible to children.
1. Connect the exhaust duct to outside exhaust system
(see pages 3 and 4). Use duct tape to seal all joints.
2. With the dryer in its final position, adjust one or more of
the legs until the dryer is resting solid on all four legs.
Place a level on top of the dryer. The dryer MUST be
level and resting solid on all four legs.
The instructions in this manual and all other
literature included with this dryer are not meant to cover
every possible condition and situation that may occur.
Good safe practice and caution MUST be applied when
installing, operating and maintaining any appliance.
3. Plug the power cord into a grounded outlet. NOTE:
Check to ensure the power is off at circuit breaker/fuse
box before plugging the power cord into the outlet.
4. Turn on the power at the circuit breaker/fuse box.
Before operating the dryer, make sure the
dryer area is clear and free from combustible materials,
gasoline, and other flammable vapors. Also see that
nothing (such as boxes, clothing, etc.) obstructs the
flow of combustion and ventilation air.
10
Download PDF
Similar pages