For Quick
Start Installation
SmartNode™ 4980 & 4990 Series
Multi-Port T1/E1/PRI VoIP eSBC
and IAD
User Manual
Important
This is a Class A device and is not intended for use in a residential environment.
Note for SN4991/F models:
This product is intended for Fiber SFP modules only. If a copper SFP module is used, it may void the CE Certification.
Sales Office: +1 (301) 975-1000
Technical Support: +1 (301) 975-1007
E-mail: support@patton.com
www.patton.com
Part Number: 07MSN4980-90-UM, Rev. D
Revised: February 28, 2017
Patton Electronics Company, Inc.
7622 Rickenbacker Drive
Gaithersburg, MD 20879 USA
Tel: +1 (301) 975-1000
Fax: +1 (301) 869-9293
Support: +1 (301) 975-1007
Web: www.patton.com
E-mail: support@patton.com
Trademark Statement
The terms SmartNode and SmartWare are trademarks of Patton Electronics Company.
All other trademarks presented in this document are the property of their
respective owners.
Copyright © 2015–2017, Patton Electronics Company. All rights reserved.
The information in this document is subject to change without notice. Patton Electronics assumes no liability for errors that may appear in this document.
Important Information
To use virtual private network (VPN) and/or AES/DES/3DES encryption capabilities
with the SmartNode 4980 and 4990 Series, you may need to purchase additional
licenses, hardware, software, network connection, and/or service. Contact sales@patton.com or +1 (301) 975-1000 for assistance.
Warranty Information
The software described in this document is furnished under a license and may be used
or copied only in accordance with the terms of such license. For information about the
license, see Appendix F, "End User License Agreement" on page 65 or go to
www.patton.com.
Patton Electronics warrants all SmartNode components to be free from defects, and
will—at our option—repair or replace the product should it fail within one year from
the first date of the shipment.
This warranty is limited to defects in workmanship or materials, and does not cover
customer damage, abuse or unauthorized modification. If the product fails to perform
as warranted, your sole recourse shall be repair or replacement as described above.
Under no condition shall Patton Electronics be liable for any damages incurred by the
use of this product. These damages include, but are not limited to, the following: lost
profits, lost savings and incidental or consequential damages arising from the use of or
inability to use this product. Patton Electronics specifically disclaims all other warranties, expressed or implied, and the installation or use of this product shall be deemed
an acceptance of these terms by the user.
Summary Table of Contents
1 General Information ..........................................................................................................................................13
2 Applications Overview .......................................................................................................................................20
3 SmartNode Installation......................................................................................................................................23
4 Initial Configuration..........................................................................................................................................30
5 Contacting Patton for Assistance ........................................................................................................................37
A Compliance Information ...................................................................................................................................40
B Specifications ....................................................................................................................................................44
C Cabling .............................................................................................................................................................52
D Port Pin-outs ....................................................................................................................................................57
E SmartNode Factory Configuration ....................................................................................................................61
F End User License Agreement .............................................................................................................................65
3
Table of Contents
Summary Table of Contents ...................................................................................................................................3
Table of Contents ...................................................................................................................................................4
List of Figures .........................................................................................................................................................7
List of Tables ..........................................................................................................................................................8
About This Guide ..................................................................................................................................................9
Audience................................................................................................................................................................. 9
Structure................................................................................................................................................................. 9
Precautions ........................................................................................................................................................... 10
Safety when working with electricity ...............................................................................................................11
.......................................................................................................................................................................12
General observations .......................................................................................................................................12
Typographical Conventions Used in this Document ............................................................................................ 12
General conventions .......................................................................................................................................12
1 General Information ..........................................................................................................................................13
SmartNode 4980 and 4990 Series Overview..........................................................................................................14
SN4980 Series model codes ............................................................................................................................15
SN4990 Series model codes ............................................................................................................................15
SmartNode 4980 and 4990 Series Rear Panels ......................................................................................................16
SN4980 Series rear panel ................................................................................................................................16
SN4990 Series rear panel ................................................................................................................................16
SmartNode 4980 and 4990 Series Front Panel ......................................................................................................18
2 Applications Overview .......................................................................................................................................20
Typical Application ...............................................................................................................................................21
3 SmartNode Installation......................................................................................................................................23
Planning the Installation........................................................................................................................................24
Site log ............................................................................................................................................................24
Network information ......................................................................................................................................24
Network Diagram ...........................................................................................................................................24
IP related information .....................................................................................................................................24
Software tools .................................................................................................................................................25
AC Power Mains .............................................................................................................................................25
Location and mounting requirements .............................................................................................................25
Installing the SmartNode.......................................................................................................................................25
Placing the SmartNode ...................................................................................................................................25
Ground Connection .......................................................................................................................................26
Installing cables ...............................................................................................................................................26
Connecting the PRI ..................................................................................................................................26
Connecting the 10/100/1000Base-T Ethernet LAN and WAN cables ......................................................27
Installation cable requirements for the DSL WAN cable (SN4991 /2G /4G /A /AVA /AVB Models) .......27
4
Model 2960 RAS Getting Started Guide
Installation cable requirements for the X.21 WAN cable (SN4991 /D Models) ........................................27
Installation cable requirements for the SFP for Fiber WAN module (SN4991) .........................................27
Installation cable requirements for the Ethernet 10/100 WAN interface (SN4991 /I Models) ..................27
Connecting the SmartNode to the IP network ..........................................................................................27
Connecting the SmartNode to the power supply .......................................................................................28
4 Initial Configuration..........................................................................................................................................30
Introduction ..........................................................................................................................................................31
1. Connecting the SmartNode to your Laptop PC ................................................................................................31
2. Configuring the Desired IP Address ..................................................................................................................32
Factory-default IP settings ...............................................................................................................................32
Login ..............................................................................................................................................................32
Changing the WAN IP address .......................................................................................................................32
3. Connecting the SmartNode to the Network ......................................................................................................33
4. Loading the Configuration (optional)................................................................................................................35
Additional Information .........................................................................................................................................36
5 Contacting Patton for Assistance ........................................................................................................................37
Introduction ..........................................................................................................................................................38
Contact Information .............................................................................................................................................38
Warranty Service and Returned Merchandise Authorizations (RMAs)...................................................................38
Warranty coverage ..........................................................................................................................................38
Out-of-warranty service .............................................................................................................................39
Returns for credit ......................................................................................................................................39
Return for credit policy .............................................................................................................................39
RMA numbers ................................................................................................................................................39
Shipping instructions ................................................................................................................................39
A Compliance Information ...................................................................................................................................40
Compliance ...........................................................................................................................................................41
EMC ...............................................................................................................................................................41
Safety ..............................................................................................................................................................41
PSTN Regulatory ............................................................................................................................................41
Radio and TV Interference ....................................................................................................................................41
FCC Part 68 (ACTA) Statement ...........................................................................................................................42
Industry Canada Notice ........................................................................................................................................42
CE Declaration of Conformity ..............................................................................................................................43
Authorized European Representative .....................................................................................................................43
B Specifications ....................................................................................................................................................44
Voice Connectivity ................................................................................................................................................45
Data Connectivity .................................................................................................................................................45
Voice Processing (signaling dependent) .................................................................................................................45
Fax and Modem Support.......................................................................................................................................45
Voice Signalling.....................................................................................................................................................46
Voice Routing—session router ..............................................................................................................................46
5
Model 2960 RAS Getting Started Guide
IP Services .............................................................................................................................................................46
Management .........................................................................................................................................................47
System ...................................................................................................................................................................47
Physical .................................................................................................................................................................47
WAN Interface (if applicable)................................................................................................................................48
Identification of the SmartNode Devices via SNMP..............................................................................................49
C Cabling .............................................................................................................................................................52
Introduction ..........................................................................................................................................................53
Console .................................................................................................................................................................53
Ethernet ................................................................................................................................................................54
E1 PRI ..................................................................................................................................................................55
T1 PRI ..................................................................................................................................................................56
D Port Pin-outs ....................................................................................................................................................57
Introduction ..........................................................................................................................................................58
Console Port..........................................................................................................................................................58
Ethernet ................................................................................................................................................................58
PRI Port ................................................................................................................................................................59
G.SHDSL ATM only port (2GS models only) ......................................................................................................59
G.SHDSL EFM & ATM port (/2G and /4G models)...........................................................................................59
ADSL & VDSL-ADSL Port (/A and /AVA & /AVB models only) ........................................................................60
Fiber Ports (/F models only) ..................................................................................................................................60
X.21 DB-15 Connector (/D models only) .............................................................................................................60
10/100 Fast Ethernet Port .....................................................................................................................................60
E SmartNode Factory Configuration ....................................................................................................................61
Introduction ..........................................................................................................................................................62
F End User License Agreement .............................................................................................................................65
End User License Agreement .................................................................................................................................66
1. Definitions ..................................................................................................................................................66
2. Title ............................................................................................................................................................66
3. Term ...........................................................................................................................................................66
4. Grant of License ..........................................................................................................................................66
5. Warranty ....................................................................................................................................................66
6. Termination ................................................................................................................................................67
7. Other licenses .............................................................................................................................................67
8. SmartWare licenses .....................................................................................................................................67
6
List of Figures
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
SmartNode 4980 (left) and SmartNode 4990 (right) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14
SN4980/SN4981 Rear Panel . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16
SN4991 Rear Panel . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16
SmartNode 4980/4990 front panel . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18
SN4980 application . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21
SN4990 application . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21
WAN uplink redundancy . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22
Power connector location on rear panel . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 28
Connecting the SmartNode to your laptop PC . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 31
Connecting the SmartNode to the network . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 33
Connecting a serial terminal . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 53
Typical Ethernet straight-through cable diagram for 10/100Base-T . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 54
Typical Ethernet straight-through cable diagram for 1000Base-T . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 54
Connecting an E1 PRI port to an NT1 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 55
E1 PRI port crossover cable . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 55
Connecting a T1 PRI port to an NT device . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 56
T1 PRI crossover cable . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 56
EIA-561 (RJ-45 8-pin) port . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 58
7
List of Tables
1
2
3
4
5
6
7
8
9
10
11
12
13
General conventions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12
Rear panel ports . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17
LED Definitions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18
Sample site log entries . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24
Factory default IP address and network mask configuration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 32
WAN Interface Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 48
SmartNode Models and their Unique sysObjectID . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 49
RJ45 socket 10/100Base-T . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 58
RJ45 socket 1000Base-T . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 58
RJ-45 socket . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 59
RJ-45 connector . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 59
EFM Port . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 59
ADSL & VDSL-ADSL Port: RJ-45 connector . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 60
8
About This Guide
This guide describes the SmartNode 4980 and 4990 Series hardware, installation and basic configuration. For
detailed software configuration information refer to the SmartWare Software Configuration Guide and the available Configuration Notes.
Audience
This guide is intended for the following users:
• Operators
• Installers
• Maintenance technicians
Structure
This guide contains the following chapters and appendices:
Chapter 1 on page 13 provides information about SmartNode features and capabilities
Chapter 2 on page 20 contains an overview describing SmartNode operation and applications
Chapter 3 on page 23 provides hardware installation procedures
Chapter 4 on page 30 provides quick-start procedures for configuring the SmartNode
Chapter 5 on page 37 contains information on contacting Patton technical support for assistance
Appendix A on page 40 contains compliance information for the SmartNode
Appendix B on page 44 contains specifications for the SmartNodes
Appendix C on page 52 provides cable recommendations
Appendix D on page 57 describes the SmartNode’s ports and pin-outs
Appendix E on page 61 lists the factory configuration settings for the SmartNode
Appendix F on page 65 provides license information that describes acceptable usage of the software provided with the SmartNode
For best results, read the contents of this guide before you install the SmartNode.
•
•
•
•
•
•
•
•
•
•
•
9
SmartNode 4980 & 4990 User Manual
Precautions
Notes, cautions, and warnings, which have the following meanings, are used throughout this guide to help you
become aware of potential problems. Warnings are intended to prevent safety hazards that could result in personal injury. Cautionsare intended to prevent situations that could result in property damage or
impaired functioning.
Note
A note presents additional information or interesting sidelights.
The alert symbol and IMPORTANT heading calls attention to
important information.
The alert symbol and CAUTION heading indicate a potential hazard. Strictly follow the instructions to avoid property damage.
The shock hazard symbol and CAUTION heading indicate a
potential electric shock hazard. Strictly follow the instructions to
avoid property damage caused by electric shock.
The alert symbol and WARNING heading indicate a potential
safety hazard. Strictly follow the warning instructions to avoid
personal injury.
The shock hazard symbol and WARNING heading indicate a
potential electric shock hazard. Strictly follow the warning
instructions to avoid injury caused by electric shock.
10
SmartNode 4980 & 4990 User Manual
Safety when working with electricity
• Do not open the device when the power cord is con-
•
•
•
•
•
•
nected. For systems without a power switch and without
an external power adapter, line voltages are present
within the device when the power cord is connected.
For devices with an external power adapter, the power
adapter shall be a listed Limited Power Source The mains
outlet that is utilized to power the device shall be within
10 feet (3 meters) of the device, shall be easily accessible, and protected by a circuit breaker in compliance with
local regulatory requirements.
For AC powered devices, ensure that the power cable
used meets all applicable standards for the country in
which it is to be installed.
For AC powered devices which have 3 conductor power
plugs (L1, L2 & GND or Hot, Neutral & Safety/Protective
Ground), the wall outlet (or socket) must have an earth
ground.
For DC powered devices, ensure that the interconnecting
cables are rated for proper voltage, current, anticipated
temperature, flammability, and mechanical serviceability.
WAN, LAN & PSTN ports (connections) may have hazardous voltages present regardless of whether the device is
powered ON or OFF. PSTN relates to interfaces such as
telephone lines, FXS, FXO, DSL, xDSL, T1, E1, ISDN,
Voice, etc. These are known as “hazardous network voltages” and to avoid electric shock use caution when
working near these ports. When disconnecting cables
for these ports, detach the far end connection first.
Do not work on the device or connect or disconnect
cables during periods of lightning activity
This device contains no user serviceable parts. This device
can only be repaired by qualified service personnel.
In accordance with the requirements of council directive 2002/96/
EC on Waste of Electrical and Electronic Equipment (WEEE),
ensure that at end-of-life you separate this product from other
waste and scrap and deliver to the WEEE collection system in
your country for recycling.
11
SmartNode 4980 & 4990 User Manual
Always follow ESD prevention procedures when removing and
replacing cards.
Wear an ESD-preventive wrist strap, ensuring that it makes good
skin contact. Connect the clip to an unpainted surface of the
chassis frame to safely channel unwanted ESD voltages
to ground.
To properly guard against ESD damage and shocks, the wrist
strap and cord must operate effectively. If no wrist strap is available, ground yourself by touching the metal part of the chassis.
General observations
• Clean the case with a soft slightly moist anti-static cloth
• Place the unit on a flat surface and ensure free air circulation
• Avoid exposing the unit to direct sunlight and other heat sources
• Protect the unit from moisture, vapors, and corrosive liquids
Typographical Conventions Used in this Document
This section describes the typographical conventions and terms used in this guide.
General conventions
The procedures described in this manual use the following text conventions:
Table 1. General conventions
Convention
Meaning
Garamond blue type
Indicates a cross-reference hyperlink that points to a figure, graphic, table, or section heading. Clicking on the hyperlink jumps you to the reference. When you
have finished reviewing the reference, click on the Go to Previous View
Futura bold type
Futura bold-italic type
Commands and keywords are in boldface font.
Parts of commands, which are related to elements already named by the user,
are in boldface italic font.
Variables for which you supply values are in italic font
Indicates the names of fields or windows.
Indicates the names of command buttons that execute an action.
Angle brackets indicate function and keyboard keys, such as <SHIFT>, <CTRL>,
<C>, and so on.
Elements in square brackets are optional.
Alternative but required keywords are grouped in braces ({ }) and are separated
by vertical bars ( | )
Terminal sessions and information the system displays are in screen font.
The leading IP address or nodename of a SmartNode is substituted with node in
boldface italic font.
The leading SN on a command line represents the nodename of the SmartNode
An hash sign at the beginning of a line indicates a comment line.
button
Italicized Futura type
Futura type
Garamond bold type
<>
[]
{a | b | c}
screen
node
SN
#
in the Adobe® Acrobat® Reader toolbar to return to your starting point.
12
Chapter 1
General Information
Chapter contents
SmartNode 4980 and 4990 Series Overview..........................................................................................................14
SN4980 Series model codes ............................................................................................................................15
SN4990 Series model codes ............................................................................................................................15
SmartNode 4980 and 4990 Series Rear Panels ......................................................................................................16
SN4980 Series rear panel ................................................................................................................................16
SN4990 Series rear panel ................................................................................................................................16
SmartNode 4980 and 4990 Series Front Panel ......................................................................................................18
13
SmartNode 4980 & 4990 User Manual
1 • General Information
SmartNode 4980 and 4990 Series Overview
The SmartNode 4980 and 4990 T1/E1 PRI VoIP Router (see Figure 1) combines Universal SIP Trunking, IP
routing, VPN/Security, and Quality of Service with high-quality Voice over IP (VoIP) delivered on 1 to 4 Primary Rate Interfaces (PRI T1/E1). This combination paves the way for enterprises’ migration to unified communications by integrating legacy telephone systems with PSTN and VoIP networks.
Figure 1. SmartNode 4980 (left) and SmartNode 4990 (right)
The SmartNode 4980 Gateway-Router and SmartNode 4990 IAD perform the following major functions:
• Up to 120 VoIP Calls—Up to 120 simultaneous voice or T.38 fax calls with one to four T1/E1/PRI ports
and dual Gigabit Ethernet ports. Use any CODEC or fax on any port, any time.
• Unified Communications Agent™—Provides any-to-any multi-path switching with VoIP and data survivability, VoIP-over-VPN security with AES/DES strong encryption, Internet Key Exchange (IKE), and SIP
Registrar
• Universal SIP and T.38 Support—Softswitch-certified signaling support between all T1 RBS CAS, ISDN
PRI, Q.SIG, SIP and H.323.
• Secure Toll-Quality VoIP—Patton’s DownStreamQoS™ and Voice-over-VPN with adaptive traffic management and shaping for maximum voice quality and secure voice communication.
• IP Routing—RIP v1/v2, VRRP, policy-based routing, and loopback interface
• Transparent Telephony Features—Complex number manipulation and mapping for seamless integration
with existing infrastructures, CLIP, CLIR, hold, transfer and much more.
• Management & Provisioning—Web-based management, SNMP, Command Line Interface. Automated
provisioning for easy large-scale deployments.
• Optional High Precision Clock—Delivers DECT PBX interoperability with reliable fax performance.
• G.SHDSL, ADSL, VDSL-ADSL, X.21, Fiber Broadband or Ethernet Access—Complete Access Router
with integrated:
- G.SHDSL.bis WAN interface delivering symmetrical throughput of up to 11.4 Mbps over four wires or
up to 5.7 Mbps over two wires
- VDSL WAN interface with upstream up to 100 Mbps and downstream up to 150 Mbps
- ADSL WAN interface with 14 Mbps
SmartNode 4980 and 4990 Series Overview
14
SmartNode 4980 & 4990 User Manual
1 • General Information
• all supporting ATM QoS with multiple PVCs and outstanding DSLAM interoperability.
In addition to:
- X.21 WAN interface up to 2 Mbps
- SFP—Fiber WAN 100 Mbps/1000 Mbps
- 3rd RJ45 Ethernet 10/100 Mbps
SN4980 Series model codes
The SmartNode 4980-90 series consists of several models. They differ in the number of PRI ports and voice
channels supported. All models come equipped with two 10/100/1000Base-T Ethernet ports.
The high precision SmartNode 4981 models have a Stratum III clock that provides a clock source of < 5 ppm.
The SN4981 can provide a PSTN-equivalent clock for PBXs that used to rely on PSTN for an accurate clock
source. The popular DECT PBX needs such high precision clocks.
SN4990 Series model codes
The SmartNode 4990 series consists of several models. They differ in the number of PRI ports and voice channels supported. All SN4991 models come equipped with two 10/100/1000Base-T Ethernet ports and a high
precision clock.
For SN4991 models, the Stratum III high precision clock provides a clock source of < 5 ppm. For PBXs that
used to rely on PSTN for accurate clock source, the SmartNode 4991 can provide a PSTN-equivalent high precision clock. The popular DECT PBX needs such high precision clocks.
For additional specific model information, refer to the product webpage.
SmartNode 4980 and 4990 Series Overview
15
SmartNode 4980 & 4990 User Manual
1 • General Information
SmartNode 4980 and 4990 Series Rear Panels
The SmartNode 4980 and 4990 rear panel ports are described in Table 2 on page 17.
SN4980 Series rear panel
0/3
0/2
0/1
T1
/E
1
0/0
ET
H
0/1
ET
0/0
Reset
H
Con
so
le
RS-
23
2
/4E120V
0/2
0/1
ETH 0/1
0/0
ETH 0/0
Console
Reset
0/3
RS-232
T1/E1
T1/E1
PRI ports 0/3–0/0
Console
ETH 0/1
RS-232 port
10/100/1000Base-T port
ETH 0/0
RESET
10/100/1000Base-T port
button
Figure 2. SN4980/SN4981 Rear Panel
SN4990 Series rear panel
Figure 3. SN4991 Rear Panel
SmartNode 4980 and 4990 Series Rear Panels
16
SmartNode 4980 & 4990 User Manual
1 • General Information
Table 2. Rear panel ports
Port
Description
ETH 0/0-0/1
Auto-MDX Gigabit-Ethernet port, RJ-45 (see Figure 2), connects the unit to an
Ethernet Expansion device (for example, a cable modem, DSL modem, or fiber
modem) or to (a PC, printer, or wireless bridge). Note: Only full duplex modes are
supported.
PRI 0/0-0/3
RJ-45 connector providing E1 (2.048Mbps) or T1(1.533 Mbps) PRI interface, meeting all requirements of ITU-T recommendations for G.703. Use a shielded E1 or T1
interface cable for 120 Ohm balanced connections to connect the SmartNode with
an NT or ET, e.g. a PBX or LE.
Expansion Port
The G.SHDSL, VDSL-ADSL, ADSL, SFP, X.21 or RJ45 Ethernet LEDs are located
on either side of the DSL port. ACT (when lit or blinking) shows Activity, and LINK
(when lit) shows that the DSL port is connected.
G.SHDSL,VDSLADSL, ADSL, SFP,
X.21, RJ45 Ethernet
(SN4991models
only)
Note
On VDSL-ADSL models (/AVA and /AVB) only, the Activity LED has
no function.
Console
Used for service and maintenance, the Console port (see Figure 2), an RS-232 RJ45 connector, connects the product to a serial terminal such as a PC or ASCII terminal (also called a dumb terminal).
12V DC, 1.0A
Electricity supply socket. (see Figure 2).
Reset
The reset button (see Figure 2) has three functions:
• Restart the unit with the current startup configuration—Press (for less than 1 second) and release the Reset button to restart the unit with the current startup configuration.
• Restart the unit with factory default configuration—Press the Reset button for
5 seconds until the Power LED starts blinking to restart the unit with factory
default configuration.
• Restart the unit in bootloader mode (to be used only by trained SmartNode
technicians)—Starting with the unit powered off, press and hold the Reset button as you apply power to the unit. Release the Reset button when the Power
LED starts blinking so the unit will enter bootloader mode.
SmartNode 4980 and 4990 Series Rear Panels
17
SmartNode 4980 & 4990 User Manual
1 • General Information
SmartNode 4980 and 4990 Series Front Panel
Figure 4 shows the SmartNode’s front panel LEDs. The LED definitions are listed in Table 3.
T1/E1
Port 0
Port 1
T1/E1
Port 2
T1/E1
Port 3
T1/E1
Ent
erpr
ise
T1/
E1
VoI Sm
P
Gat artN
ew
od
ay
-R e
ou
ter
/1E30V
SmartNode
Enterprise T1/E1 VoIP Gateway-Router
Power
Activity
T1/E1 Port 0
Ethernet 0/1
Activity
VoIP
Ethernet 0/0
Link
Ethernet 0/0
1000
Ethernet 0/0
100
Ethernet 0/1
Link
Ethernet 0/0
Activity
Ethernet 0/1
1000
Ethernet 0/1
100
/4E120V
SmartNode
T1
/E
1
T1 Por
t0
/E
1
Po
T1
/E rt 1
1
Po
T1
/E rt 2
1
Po
rt
3
Enterprise T1/E1 VoIP Gateway-Router
T1/E1 Port 0
T1/E1 Port 1
T1/E1 Port 3
T1/E1 Port 2
Figure 4. SmartNode 4980/4990 front panel
Table 3. LED Definitions
LED
Note
Description
If an error occurs, all LEDs will flash once per second.
Power
When lit, indicates power is applied.
Run
When lit, the unit is in normal operation; flashes once per second during boot
(startup).
SmartNode 4980 and 4990 Series Front Panel
18
SmartNode 4980 & 4990 User Manual
1 • General Information
Table 3. LED Definitions (Continued)
LED
VoIP Link
Description
• On indicates the gateway is registered to an H.323 gatekeeper/SIP
server, or, in the case of direct routing, has at least one active VoIP connection.
• Off indicates the unit is not configured or registered, or has no active
direct-routed VoIP connection.
• Flashing green indicates that the unit is attempting to register or has
failed to register.
Ethernet Link
• On when the Ethernet connection on the corresponding port has a link
indication.
Ethernet Speed
When the Ethernet Link LED is on, then:
10/100
• On when the Ethernet is connected to a 100Mb network.
• Off when the Ethernet is connected to a 10Mb network.
• On when the Ethernet is connected to a 1000Mb network.
Ethernet Speed
1000
Ethernet Activity
• Flashes when data is received or transmitted at the corresponding
Ethernet port.
PRI Link/Status
• On = in frame, no errors
• Flash = Error
• Fast Flash = Signal detected but no frame synchronization or acquisition
is in process
• Slow Flash = Framing synchronized, Signaling not established
WAN ACT/Link LEDs (SN4991 models only)
WAN ACT
(Rear panel)
• Flashes when data is received or transmitted
• Off = No activity
Note
WAN Link
(Rear panel)
On VDSL-ADSL models (/AVA and /AVB) only, the Activity
LED has no function.
• On when the WAN connection on the corresponding port has a link indication.
• Off when there is no WAN connection
SmartNode 4980 and 4990 Series Front Panel
19
Chapter 2
Applications Overview
Chapter contents
Typical Application ...............................................................................................................................................21
20
SmartNode 4980 & 4990 User Manual
2 • Applications Overview
Typical Application
IP-enable legacy PBX systems with an Enterprise-class SmartNode 4980 VoIP Gateway-Router or SmartNode
4990 Integrated Access Device.The SN4980 and SN4990 support up to 120 concurrent VoIP calls.
The SN4980 with built-in IP Router enables Enterprises to connect existing PBX systems with advanced IP
telephony services and the PSTN. With built-in G.SHDSL, ADSL, Fiber or X.21, the SN4990 enables Broadband Providers to connect existing PBX systems with advanced IP telephony services and the PSTN.
Combining a VoIP gateway with an IP router, the SmartNode 4980 and 4990 Series adds QoS and VPN security, making it the ideal solution for secure prioritized communications.
Figure 5. SN4980 application
Figure 6. SN4990 application
Typical Application
21
SmartNode 4980 & 4990 User Manual
2 • Applications Overview
Figure 7. WAN uplink redundancy
Typical Application
22
Chapter 3
SmartNode Installation
Chapter contents
Planning the Installation........................................................................................................................................24
Site log ............................................................................................................................................................24
Network information ......................................................................................................................................24
Network Diagram ...........................................................................................................................................24
IP related information .....................................................................................................................................24
Software tools .................................................................................................................................................25
AC Power Mains .............................................................................................................................................25
Location and mounting requirements .............................................................................................................25
Installing the SmartNode.......................................................................................................................................25
Placing the SmartNode ...................................................................................................................................25
Ground Connection .......................................................................................................................................26
Installing cables ...............................................................................................................................................26
Connecting the PRI ..................................................................................................................................26
Connecting the 10/100/1000Base-T Ethernet LAN and WAN cables ......................................................27
Installation cable requirements for the DSL WAN cable (SN4991 /2G /4G /A /AVA /AVB Models) .......27
Installation cable requirements for the X.21 WAN cable (SN4991 /D Models) ........................................27
Installation cable requirements for the SFP for Fiber WAN module (SN4991) .........................................27
Installation cable requirements for the Ethernet 10/100 WAN interface (SN4991 /I Models) ..................27
Connecting the SmartNode to the IP network ..........................................................................................27
Connecting the SmartNode to the power supply .......................................................................................28
23
SmartNode 4980 & 4990 User Manual
3 • SmartNode Installation
Planning the Installation
Before installing the SmartNode, the following tasks should be completed:
• Create a network diagram (see section “Network information” on page 24)
• Gather IP related information (see section “IP related information” on page 24 for more information)
• Install the hardware and software needed to configure the SmartNode. (See section “Software tools” on
page 25)
• Verify power source reliability (see section “AC Power Mains” on page 25).
After you have finished preparing for installation, go to the section “Installing the SmartNode” on page 25 to
install the device.
Site log
Patton recommends that you maintain a site log to record all actions relevant to the system, if you do not
already keep such a log. Site log entries should include information such as listed in Table 4.
Table 4. Sample site log entries
Entry
Description
Installation
Make a copy of the installation checklist and insert it into the site log
Upgrades and maintenance
Use the site log to record ongoing maintenance and expansion history
Configuration changes
Record all changes and the reasons for them
Maintenance
Schedules, requirements, and procedures performed
Comments
Notes, and problems
Software
Changes and updates to SmartWare software
Network information
Network connection considerations that you should take into account for planning are provided for several
types of network interfaces are described in the following sections.
Network Diagram
Draw a network overview diagram that displays all neighboring IP nodes, connected elements and
telephony components.
IP related information
Before you can set up the basic IP connectivity for your SmartNode, you should have the following information:
• IP addresses used for Ethernet LAN and WAN ports
• Subnet mask used for Ethernet LAN and WAN ports
Planning the Installation
24
SmartNode 4980 & 4990 User Manual
3 • SmartNode Installation
• IP addresses of central H.323 gatekeeper (if used)
• IP addresses and/or URL of SIP servers or Internet telephony services (if used)
• Login and password for PPPoE Access
• Login and password for SIP or H.323 based telephony services
• IP addresses of central TFTP server used for configuration upload and download (optional)
Software tools
You will need a PC (or equivalent) with Windows Telnet or a program such as Tera Term Pro Web to configure
the software on your SmartNode.
AC Power Mains
If you suspect that your AC power is not reliable, for example if room lights flicker often or there is machinery
with large motors nearby, have a qualified professional test the power. Patton recommends that you include an
uninterruptible power supply (UPS) in the installation to ensure that VoIP service is not impaired if the
power fails. Refer to “Connecting the SmartNode to the power supply” on page 28.
Location and mounting requirements
The SmartNode is intended to be placed on a desktop or similar sturdy, flat surface that offers easy access to the
cables. Allow sufficient space at the rear of the chassis for cable connections. Additionally, you should consider
the need to access the unit for future upgrades and maintenance.
Note
Under the rack mount option, the chassis can be equipped with rack mount
ears that allow for use in a 19” rack.
Installing the SmartNode
SmartNode hardware installation consists of the following:
• Placing the device at the desired installation location (see section “Placing the SmartNode” on page 25)
• Connecting the interface and power cables (see section “Installing cables”)
When you finish installing the SmartNode, go to chapter 4, “Initial Configuration” on page 30.
Placing the SmartNode
Place the unit on a desktop or similar sturdy, flat surface that offers easy access to the cables. The unit should be
installed in a dry environment with sufficient space to allow air circulation for cooling.
Note
For proper ventilation, leave at least 2 inches (5 cm) to the left, right, front,
and rear of the unit.
Installing the SmartNode
25
SmartNode 4980 & 4990 User Manual
3 • SmartNode Installation
Ground Connection
To be compliant with safety regulations (EN60950-1, UL609501 and CAN/CSA-C22.2 No 60950), the ground terminal must be
connected to a reliable ground.
3A
Installing cables
Do not work on the system or connect or disconnect
cables during periods of lightning activity.
Connect the cables in the following order:
The interconnecting cables shall be acceptable for external use
and shall be rated for the proper application with respect to voltage, current, anticipated temperature, flammability, and
mechanical serviceability.
1. Connect the T1/E1 cables to the PRI T1/E1 ports (see Appendix C on page 52 and Appendix D on
page 57).
2. Connect the 10/100/1000Base-T Ethernet LAN and WAN (see section “Connecting the 10/100/
1000Base-T Ethernet LAN and WAN cables” on page 27)
3. Connect the power mains cable (see section “Connecting the SmartNode to the power supply” on page 28)
Connecting the PRI
The SmartNode comes with one or four PRI ports. These ports are usually connected to a PBX or switch (local
exchange (LE) ). Each PRI T1/E1 port is a RJ-48C receptacle. In most cases, a straight-through RJ-45 can be used
to connect the PRI. Each port can be configured as NT (clock master) or TE (clock slave).
For details on the PRI port pin-out and ISDN cables, refer to Appendix C, “Cabling” on page 43 and Appendix D, “port pin-outs” on page 47.
For the ISDN connection to a carrier Network, it shall be connected to a Network Termination Device and not connected
directly to an outside POTS line.
Installing the SmartNode
26
SmartNode 4980 & 4990 User Manual
3 • SmartNode Installation
Connecting the 10/100/1000Base-T Ethernet LAN and WAN cables
The SmartNode has automatic MDX (auto-crossover) detection and configuration on all Ethernet ports. Any
of the ports can be connected to a host or hub/switch with a straight-through or cross-over wired cable.
1. Connect to the subscriber port of the broadband access modem (DSL, cable, WLL) to ETH 0/0.
Note
The SmartNode Ethernet ports operate in Full Duplex mode only. Do not
connect to Half Duplex ports. For best results, use auto-negotiation. Auto
negotiation is mandatory when using 1000BaseT (Gigabit) Ethernet.
2. Connect port ETH 0/1 to your LAN.
For details on the Ethernet port pinout and cables, refer to Appendix C, “Cabling” on page 52 and Appendix
D, “Port Pin-outs” on page 57.
Installation cable requirements for the DSL WAN cable (SN4991 /2G /4G /A /AVA /AVB Models)
The SmartNode Model 4991 comes with an option for a G.SHDSL, VDSL-ADSL or ADSL WAN interface. Use
a straight-through RJ-45 cable to connect the DSL port.
For details on the G.SHDSL port pinout, refer to section “G.SHDSL ATM only port (2GS models only)” on
page 59.
For details on the VDSL and ADSL port pinout, refer to section “ADSL & VDSL-ADSL Port (/A and /AVA & /
AVB models only)” on page 60.
Installation cable requirements for the X.21 WAN cable (SN4991 /D Models)
The SmartNode Model 4991 comes with an option for an X.21 serial interface. Insert the X.21 WAN cable’s
DB-15 male end into the DB-15 connector on the SN4991. Plug the other end of the cable into the X.21
device.
For details on the X.21interface pinout, refer to “X.21 DB-15 Connector (/D models only)” on page 60.
Installation cable requirements for the SFP for Fiber WAN module (SN4991)
The SmartNode Model 4991 comes with an option for an SFP for Fiber WAN module. For details about the
tested and compatible SFP modules see http://www.patton.com/products/sfpmodules.asp.
Installation cable requirements for the Ethernet 10/100 WAN interface (SN4991 /I Models)
The SmartNode Model 4991 comes with an option for a 3rd Ethernet 10/100 port to be used as a WAN interface for instance. Use a straight through RJ-45 cable to connect the Ethernet WAN port.
For details on the Ethernet port pinout, refer to Appendix D on page 57.
Connecting the SmartNode to the IP network
The SmartNode comes with two 10/100/100 Base-Tx Ethernet ports (Gigabit) for connection to an IP network. (Some models come with 3 Ethernet ports, see /I Models). The Ethernet WAN interface is factory-configured as a DHCP client, so you must connect the SmartNode to an IP network that provides a DHCP server.
The Ethernet port (ETH) includes an automatic MDX (auto-crossover) feature that automatically detects the
cable configuration and adjusts accordingly. The feature allow you to use a straight-through Ethernet cable to
Installing the SmartNode
27
SmartNode 4980 & 4990 User Manual
3 • SmartNode Installation
connect to an Ethernet hub or switch. Typically the hub or switch will connect to a router that provides the the
local-residential IP network with broadband Internet access.
Using the included black Ethernet cable, connect the RJ-45 Ethernet WAN port on your SmartNode (labeled
ETH), to an Ethernet hub or switch on the same network as your PC.
For details on the Ethernet port pinout and cables, refer to Appendix C on page 52 and Appendix D on
page 57.
Connecting the SmartNode to the power supply
• Do not connect power to the AC Mains at this time.
• The external power adapter shall be a listed Limited Power
Source.
• The 4980 external power supply automatically adjusts to
accept an input voltage from 100 to 240 VAC (50/60 Hz).
Verify that the proper voltage is present before plugging the
power cord into the receptacle. Failure to do so could result in
equipment damage.
• The external power supply automatically adjusts to accept an
input voltage from 100 to 240 VAC (50/60 Hz).
• Verify that the proper voltage is present before plugging the
power cord into the receptacle. Failure to do so could result in
equipment damage.
1. Insert the barrel type connector end of the AC power cord into the 12V DC, 1.0A port (see Figure 8).
2. Insert the female end of the power cord into the internal power supply connector.
3A
Figure 8. Power connector location on rear panel
3. Verify that the AC power cord included with your SmartNode is compatible with local standards. If it is
not, refer to chapter 5, “Contacting Patton for Assistance” on page 37 to find out how to replace it with a
compatible power cord.
Installing the SmartNode
28
SmartNode 4980 & 4990 User Manual
3 • SmartNode Installation
4. Connect the male end of the power cord to an appropriate power outlet.
5. Verify that the green Power LED is lit (see Figure 8).
Installing the SmartNode
29
Chapter 4
Initial Configuration
Chapter contents
Introduction ..........................................................................................................................................................31
1. Connecting the SmartNode to your Laptop PC ................................................................................................31
2. Configuring the Desired IP Address ..................................................................................................................32
Factory-default IP settings ...............................................................................................................................32
Login ..............................................................................................................................................................32
Changing the WAN IP address .......................................................................................................................32
3. Connecting the SmartNode to the Network ......................................................................................................33
4. Loading the Configuration (optional)................................................................................................................35
Additional Information .........................................................................................................................................36
30
SmartNode 4980 & 4990 User Manual
4 • Initial Configuration
Introduction
This chapter leads you through the basic steps to set up a new SmartNode and to download a configuration.
Setting up a new SmartNode consists of the following main steps:
Note
If you haven’t already installed the SmartNode, refer to chapter 3,
“SmartNode Installation” on page 23.
• Connecting the SmartNode to your laptop PC
• Configuring the desired IP address
• Connecting the SmartNode to the network
• Loading the configuration (optional)
1. Connecting the SmartNode to your Laptop PC
First the SmartNode must be connected to the mains power supply with the power cable. Wait until the Power
LED stops blinking and stays lit constantly. Now the SmartNode is ready.
The interconnecting cables shall be acceptable for external use
and shall be rated for the proper application with respect to voltage, current, anticipated temperature, flammability, and
mechanical serviceability.
The SmartNode 4980 and 4990 Series is equipped with Auto-MDX Ethernet ports, so you can use straightthrough cables for host or hub/switch connections (see Figure 9).
0/3
0/2
0/1
T1
/E1
0/0
ET
H
0/1
H
0/0
Reset
ET
Co
ns
RS
ole
-23
2
LAN (connect to ETH 0/1)
Ethernet
Laptop PC
Figure 9. Connecting the SmartNode to your laptop PC
The SmartNode comes with a built-in DHCP server to simplify configuration. Therefore, to automatically
configure the PC for IP connectivity to the SmartNode, the laptop PC must be configured for DHCP. The
SmartNode will provide the PC with an IP address. You can check the connection to the SmartNode by executing the ping command from the PC command window as follows:
ping 192.168.1.1
Introduction
31
SmartNode 4980 & 4990 User Manual
4 • Initial Configuration
2. Configuring the Desired IP Address
Factory-default IP settings
The factory default configuration for the Ethernet interface IP addresses and network masks are listed in Table 5.
Both Ethernet interfaces are activated upon power-up. LAN interface ETH 0/1 (LAN) provides a default
DHCP server, the WAN interface uses DHCP client to automatically assign the IP address and network mask.
Table 5. Factory default IP address and network mask configuration
IP Address
Network Mask
WAN interface Ethernet 0 (ETH 0/0)
DHCP
DHCP
LAN interface Ethernet 1 (ETH 0/1)
192.168.1.1
255.255.255.0
WAN interface Ethernet 2 (ETH 0/2)
DHCP address range
DHCP
DHCP
192.168.1.10–192.168.1.99
255.255.255.0
If these addresses match with those of your network, go to section “3. Connecting the SmartNode to the Network” on page 33. Otherwise, refer to the following sections to change the addresses and network masks.
Note
For configuring the IP address of the integrated WAN interface (G.SHDSL),
please refer to Chapter 5, “G.SHDSL Basic Configuration” on page 36.
Login
To access the SmartNode, start the Telnet application. Type the default IP address for the SmartNode into the
address field: 192.168.1.1. Accessing your SmartNode via a Telnet session displays the login screen. Type the
factory default login: administrator and leave the password empty. Press the Enter key after the password
prompt.
login:administrator
password: <Enter>
192.168.1.1>
After you have successfully logged in you are in the operator execution mode, indicated by > as command line
prompt. With the commands enable and configure you enter the configuration mode.
192.168.1.1>enable
192.168.1.1#configure
192.168.1.1(cfg)#
Changing the WAN IP address
Select the context IP mode to configure an IP interface.
192.168.1.1(cfg)#context ip router
192.168.1.1(ctx-ip)[router]#
2. Configuring the Desired IP Address
32
SmartNode 4980 & 4990 User Manual
4 • Initial Configuration
Now you can set your IP address and network mask for the interface ETH 0/0 (WAN). Within this example a
network 172.16.1.0/24 address is assumed. The IP address in this example is set to 172.16.1.99 (you should set
this the IP address given to you by your network provider).
192.168.1.1(ctx-ip)[router]#interface WAN
192.168.1.1(if-ip)[WAN]#ipaddress 172.16.1.99 255.255.255.0
2002-10-29T00:09:40 : LOGINFO
: Link down on interface WAN.
2002-10-29T00:09:40 : LOGINFO
: Link up on interface WAN.
172.16.1.99(if-ip)[WAN]#
Copy this modified configuration to your new start-up configuration. This will store your changes in non-volatile memory. Upon the next start-up the system will initialize itself using the modified configuration.
172.16.1.99(if-ip)[WAN]#copy running-config startup-config
172.16.1.99(if-ip)[WAN]#
The SmartNode can now be connected to your network.
3. Connecting the SmartNode to the Network
In general, the SmartNode will connect to the network via the WAN (ETH 0/0) port. This enables the SmartNode to offer routing services to the PC hosts on LAN (ETH 0/1) port. The SmartNode 4980 and 4990 Series
is equipped with Auto-MDX Ethernet ports, so you can use straight-through or crossover cables for host or
hub/switch connections (see Figure 10).
The interconnecting cables shall be acceptable for external use
and shall be rated for the proper application with respect to voltage, current, anticipated temperature, flammability, and
mechanical serviceability.
0/3
0/2
0/1
T1
/E1
0/0
ET
H
0/1
0/0
Reset
ET
H
LAN
Co
ns
ole
RS
-23
2
LAN (ETH 0/1)
WAN (ETH 0/0)
Straight-through wired or crossover cable
Network
Figure 10. Connecting the SmartNode to the network
3. Connecting the SmartNode to the Network
33
SmartNode 4980 & 4990 User Manual
4 • Initial Configuration
You can check the connection with the ping command from the SmartNode to another host on the network.
172.16.1.99(if-ip)[WAN]#ping <IP Address of the host>
3. Connecting the SmartNode to the Network
34
SmartNode 4980 & 4990 User Manual
Note
4 • Initial Configuration
If the WAN address is notset to DHCP, to ping a device outside your local
LAN you must first configure the default gateway. (For information on configuring the default gateway, refer to section “Set IP addresses” in Appendix
C, “Command Summary” of the SmartNode Series SmartWare Software Configuration Guide.)
4. Loading the Configuration (optional)
Patton provides a collection of configuration templates on the support page at www.patton.com/smartnode—
one of which may be similar enough to your application that you can use it to speed up configuring the SmartNode. Simply download the configuration note that matches your application to your PC. Adapt the configuration as described in the configuration note to your network (remember to modify the IP address) and copy
the modified configuration to a TFTP server. The SmartNode can now load its configuration from this server.
Note
If your application is unique and not covered by any of Patton’s configuration templates, you can manually configure the SmartNode instead of loading a configuration file template. In that case, refer to the SmartNode Series
SmartWare Software Configuration Guide for information on configuring the
SmartNode device.
In this example we assume the TFTP server on the host with the IP address 172.16.1.11 and the configuration
named SN.cfg in the root directory of the TFTP server.
172.16.1.99(if-ip)[WAN]#copy tftp://172.16.1.11/SN.cfg startup-config
Download...100%
172.16.1.99(if-ip)[WAN]#
After the SmartNode has been rebooted the new startup configuration will be activated.
When you issue the reload command, the SmartNode will ask
if you want to copy the running configuration to the startup configuration. Since you just downloaded a configuration file to the
startup configuration you must answer this question with NO.
Otherwise, the downloaded configuration will be overwritten
and lost!
172.16.1.99(if-ip)[WAN]#reload
Running configuration has been changed.
Do you want to copy the 'running-config' to the 'startup-config'?
Press 'yes' to store, 'no' to drop changes : no
Press 'yes' to restart, 'no' to cancel : yes
The system is going down
4. Loading the Configuration (optional)
35
SmartNode 4980 & 4990 User Manual
4 • Initial Configuration
Additional Information
For detailed information about configuring and operating guidance, set up procedures, and troubleshooting,
refer to the SmartNode Series SmartWare Software Configuration Guide available online at www.patton.com/
manuals.
Additional Information
36
Chapter 5
Contacting Patton for Assistance
Chapter contents
Introduction ..........................................................................................................................................................38
Contact Information .............................................................................................................................................38
Warranty Service and Returned Merchandise Authorizations (RMAs)...................................................................38
Warranty coverage ..........................................................................................................................................38
Out-of-warranty service .............................................................................................................................39
Returns for credit ......................................................................................................................................39
Return for credit policy .............................................................................................................................39
RMA numbers ................................................................................................................................................39
Shipping instructions ................................................................................................................................39
37
SmartNode 4980 & 4990 User Manual
5 • Contacting Patton for Assistance
Introduction
This chapter contains the following information:
• “Contact Information”—describes how to contact Patton technical support for assistance.
• “Warranty Service and Returned Merchandise Authorizations (RMAs)”—contains information about the
warranty and obtaining a return merchandise authorization (RMA).
Contact Information
Patton Electronics offers a wide array of free technical services. If you have questions about any of our other
products we recommend you begin your search for answers by using our technical knowledge base. Here, we
have gathered together many of the more commonly asked questions and compiled them into a searchable
database to help you quickly solve your problems.
REGION
North America
Western Europe
Central & Eastern
Europe
Middle East North
Africa
Location
Maryland, USA
Bern, Switzerland
Budapest, Hungary
Beirut, Lebanon
Time Zone
EST/EDT
CET/CEDT
CET/CEDT
EET/EEDT
UTC/GMT - 4/5 hours
UTC/GMT + 1/2 hours
UTC/GMT + 1/2 hours
UTC/GMT + 2/3 hours
Monday-Friday
Monday-Friday
Monday-Friday
Monday-Friday
8:00am to 5:00pm
09:00 to 12:00
8:30 to 17:00
8:00am to 5pm
support@patton.com
support@patton.com
+36 439 3835
+96 1 359 1277
Business
Hours
13:30 to 17:30
Email
support@patton.com support@patton.com
Phone
+ 1 301 975 1007
+41 31 985 25 55
Fax
+1 301 869 9293
+41 31 985 2526
Warranty Service and Returned Merchandise Authorizations (RMAs)
Patton Electronics is an ISO-9001 certified manufacturer and our products are carefully tested before shipment. All of our products are backed by a comprehensive warranty program.
Note
If you purchased your equipment from a Patton Electronics reseller, ask your
reseller how you should proceed with warranty service. It is often more convenient for you to work with your local reseller to obtain a replacement.
Patton services our products no matter how you acquired them.
Warranty coverage
Our products are under warranty to be free from defects, and we will, at our option, repair or replace the product should it fail within one year from the first date of shipment. Our warranty is limited to defects in workmanship or materials, and does not cover customer damage, lightning or power surge damage, abuse, or
unauthorized modification.
Introduction
38
SmartNode 4980 & 4990 User Manual
5 • Contacting Patton for Assistance
Out-of-warranty service
Patton services what we sell, no matter how you acquired it, including malfunctioning products that are no
longer under warranty. Our products have a flat fee for repairs. Units damaged by lightning or other catastrophes may require replacement.
Returns for credit
Customer satisfaction is important to us, therefore any product may be returned with authorization within 30
days from the shipment date for a full credit of the purchase price. If you have ordered the wrong equipment or
you are dissatisfied in any way, please contact us to request an RMA number to accept your return. Patton is
not responsible for equipment returned without a Return Authorization.
Return for credit policy
• Less than 30 days: No Charge. Your credit will be issued upon receipt and inspection of the equipment.
• 30 to 60 days: We will add a 20% restocking charge (crediting your account with 80% of the purchase
price).
• Over 60 days: Products will be accepted for repairs only.
RMA numbers
RMA numbers are required for all product returns. You can obtain an RMA by doing one of the following:
• Completing a request on the RMA Request page in the Support section at www.patton.com
• By calling +1 (301) 975-1007 and speaking to a Technical Support Engineer
• By sending an e-mail to returns@patton.com
All returned units must have the RMA number clearly visible on the outside of the shipping container. Please use
the original packing material that the device came in or pack the unit securely to avoid damage during shipping.
Shipping instructions
The RMA number should be clearly visible on the address label. Our shipping address is as follows:
Patton Electronics Company
RMA#: xxxx
7622 Rickenbacker Dr.
Gaithersburg, MD 20879-4773 USA
Patton will ship the equipment back to you in the same manner you ship it to us. Patton will pay the return
shipping costs.
Warranty Service and Returned Merchandise Authorizations (RMAs)
39
Appendix A Compliance Information
Chapter contents
Compliance ...........................................................................................................................................................41
EMC ...............................................................................................................................................................41
Safety ..............................................................................................................................................................41
PSTN Regulatory ............................................................................................................................................41
Radio and TV Interference ....................................................................................................................................41
FCC Part 68 (ACTA) Statement ...........................................................................................................................42
Industry Canada Notice ........................................................................................................................................42
CE Declaration of Conformity ..............................................................................................................................43
Authorized European Representative .....................................................................................................................43
40
SmartNode 4980 & 4990 User Manual
A • Compliance Information
Compliance
EMC
• FCC Part 15, Class A
• EN55022, Class A
• EN55024
Safety
• UL 60950-1/CSA C22.2 N0. 60950-1
• IEC/EN60950-1
• AS/NZS 60950-1
PSTN Regulatory
• FCC Part 68
• CS-03
• TBR 4
• TBR 12 & 13
• AS/ACIF S016
• AS/ACIF S038
• AS/ACIF S043 (G.SHDSL card)
• NZ ISDN Layer 3 Supplement
For the ISDN connection to a carrier network, it shall be connected to a network termination device and not connected
directly to an outside POTS line.
Radio and TV Interference
The SmartNode router generates and uses radio frequency energy, and if not installed and used properly—that
is, in strict accordance with the manufacturer’s instructions—may cause interference to radio and television
reception. The SmartNode router has been tested and found to comply with the limits for a Class A computing
device in accordance with specifications in Subpart B of Part 15 of FCC rules, which are designed to provide
reasonable protection from such interference in a commercial installation. However, there is no guarantee that
interference will not occur in a particular installation. If the SmartNode router does cause interference to radio
or television reception, which can be determined by disconnecting the unit, the user is encouraged to try to
correct the interference by one or more of the following measures: moving the computing equipment away
from the receiver, re-orienting the receiving antenna and/or plugging the receiving equipment into a different
AC outlet (such that the computing equipment and receiver are on different branches).
Compliance
41
SmartNode 4980 & 4990 User Manual
A • Compliance Information
FCC Part 68 (ACTA) Statement
This equipment complies with Part 68 of FCC rules and the requirements adopted by ACTA. On the bottom
side of this equipment is a label that contains—among other information—a product identifier in the format
US: AAAEQ##TXXXX. If requested, this number must be provided to the telephone company.
The method used to connect this equipment to the premises wiring and telephone network must comply with
the applicable FCC Part 68 rules and requirements adopted by the ACTA.
If this equipment causes harm to the telephone network, the telephone company will notify you in advance
that temporary discontinuance of service may be required. But if advance notice isn’t practical, the telephone
company will notify the customer as soon as possible. Also, you will be advised of your right to file a complaint
with the FCC if you believe it is necessary.
The telephone company may make changes in its facilities, equipment, operations or procedures that could
affect the operation of the equipment. If this happens the telephone company will provide advance notice in
order for you to make necessary modifications to maintain uninterrupted service.
If trouble is experienced with this equipment, for repair or warranty information, please contact our company.
If the equipment is causing harm to the telephone network, the telephone company may request that you disconnect the equipment until the problem is resolved.
Connection to party line service is subject to state tariffs. Contact the state public utility commission, public
service commission or corporation commission for information.
Industry Canada Notice
This equipment meets the applicable Industry Canada Terminal Equipment Technical Specifications. This is
confirmed by the registration number. The abbreviation, IC, before the registration number signifies that registration was performed based on a Declaration of Conformity indicating that Industry Canada technical specifications were met. It does not imply that Industry Canada approved the equipment.
This Declaration of Conformity means that the equipment meets certain telecommunications network protective, operational and safety requirements. The Department does not guarantee the equipment will operate to
the user's satisfaction. Before installing this equipment, users should ensure that it is permissible to be connected to the facilities of the local telecommunications company. The equipment must also be installed using
an acceptable method of connection. In some cases, the company’s inside wiring associated with a single line
individual service may be extended by means of a certified connector assembly (telephone extension cord). The
customer should be aware that compliance with the above condition may not prevent degradation of service in
some situations. Repairs to some certified equipment should be made by an authorized maintenance facility
designated by the supplier. Any repairs or alterations made by the user to this equipment, or equipment malfunctions, may give the telecommunications company cause to request the user to disconnect the equipment.
Users should ensure for their own protection that the ground connections of the power utility, telephone lines
and internal metallic water pipe system, are connected together. This protection may be particularly important
in rural areas.
FCC Part 68 (ACTA) Statement
42
SmartNode 4980 & 4990 User Manual
A • Compliance Information
CE Declaration of Conformity
We certify that the apparatus identified above conforms to the requirements of Council Directive 2004/108/
EC on the approximation of the laws of the member states relating to electromagnetic compatibility; and
Council Directive 2006/95/EC on the approximation of the laws of the member states relating to electrical
equipment designed for use within certain voltage limits; Council Directive 2009/125/EC establishing a
framework for the setting of Ecodesign requirements for energy-related products; and Council Directive 2011/
65/EU on the approximation of the laws of the member states relating to RoHS compliance.
The safety advice in the documentation accompanying this product shall be obeyed. The conformity to the
above directive is indicated by CE sign on the device.
The signed Declaration of Conformity can be downloaded at www.patton.com/certifications.
Authorized European Representative
D R M Green
European Compliance Services Ltd
Avalon House
Marcham Road
Abingdon
Oxon OX14 1UD, UK
CE Declaration of Conformity
43
Appendix B Specifications
Chapter contents
Voice Connectivity ................................................................................................................................................45
Data Connectivity .................................................................................................................................................45
Voice Processing (signaling dependent) .................................................................................................................45
Fax and Modem Support.......................................................................................................................................45
Voice Signalling.....................................................................................................................................................46
Voice Routing—session router ..............................................................................................................................46
IP Services .............................................................................................................................................................46
Management .........................................................................................................................................................47
System ...................................................................................................................................................................47
Physical .................................................................................................................................................................47
WAN Interface (if applicable)................................................................................................................................48
Identification of the SmartNode Devices via SNMP..............................................................................................49
44
SmartNode 4980 & 4990 User Manual
Note
B • Specifications
Refer to the software feature matrix for the most up-to-date specifications.
Voice Connectivity
1 or 4 PRI T1/E1 ports on RJ48C connectors
Net/User configurable per port
Each port can be slave or master clock
Each port can be used to synchronize to an external clock master
Failover relay between ports 0/0 and 0/1 for specific models
Data Connectivity
Two 10/100/1000Base-Tx Gigabit Ethernet ports
All ports full duplex, autosensing, auto-MDX
Voice Processing (signaling dependent)
Up to 120 full-duplex channels with Voice CODECS:
• G.711 A-Law/μ-Law (64 kbps)
• G.726 (ADPCM 16, 24, 32, 40 kbps)
• G.723.1 (5.3 or 6.3 kbps)
• G.729ab (8 kbps)
• Transparent ISDN data
G.168 echo cancellation (128 ms)
Up to 120 simultaneous voice or T.38 fax calls
DTMF detection and generation
Carrier tone detection and generation
Silence suppression and comfort noise
Adaptive and configurable dejitter buffer
Configurable tones (dial, ringing, busy)
Configurable transmit packet length
RTP/RTCP (RFC 1889)
Fax and Modem Support
Automatic fax and modem detection
Codec fallback for modem-bypass
T.38 Fax-Relay (Gr. 3 Fax, 9.6 k, 14.4 k)
Voice Connectivity
45
SmartNode 4980 & 4990 User Manual
B • Specifications
G.711 Fax-Bypass
Voice Signalling
SIPv2
H.323v4
SIP call transfer, redirect
Overlap or en-bloc dialing
DTMF in-band, out-of-band
Configurable progress tones
Voice Routing—session router
Local switching (hairpinning)
Least cost routing
Interface huntgroups
Call-Distribution groups
Number blocking
Call Routing Criteria:
• Interface
• Calling/called party number
• Time of day, day of week, date
• ISDN bearer capability
• Various other information elements (IEs) of the ISDN setup
• Wildcard and regular expression matching
Regular expression number manipulation functions:
• Replace numbers
• Add/remove digits
• Pattern matching and replacement
IP Services
IPv4 router; RIPv1, v2 (RFC 1058 and 2453)
Programmable static routes
ICMP redirect (RFC 792); Packet fragmentation
DiffServe/ToS set or queue per header bits
Packet Policing discards excess traffic
Voice Signalling
46
SmartNode 4980 & 4990 User Manual
B • Specifications
802.1p VLAN tagging
IPSEC AH & ESP Modes
Manual Key; IKE
AES/DES/3DES Encryption
Management
Web-based GUI
Industry standard CLI with local console (RJ-45, RJ-231, 9600 bps, 8, N, 1) and remote Telnet access, fully
documented
HTTP web management and firmware loading
TFTP configuration & firmware loading
SNMP v1 agent (MIB II and private MIB)
Built-in diagnostic tools (trace, debug)
Secure Auto-provisioning
System
CPU Motorola MPC8360 series operating at 400 MHz
Memory:
• 256 Mbytes RAM (DDR, 400MHz)
• 32 Mbytes Flash
Physical
Dimensions: 11.9W x 1.71H x 7.16D inch (302W x 44H x 182mm)
Weight: <21 oz. (<600g)
Power Consumption: < 16W
Operating temperature: 32–104°F (0–40°C)
Operating humidity: up to 90%, non condensing
Management
47
SmartNode 4980 & 4990 User Manual
B • Specifications
WAN Interface (if applicable)
Note
For information on configuring the WAN interface, see Chapter 4, “Initial
Configuration” on page 30.
Table 6. WAN Interface Specifications
Factor
Specs
VDSL-ADSL
(/AVA and /AVB models)
•
•
•
•
•
•
•
•
•
•
•
•
•
ANSI T1.413 Issue 2
G.992.1 (G.dmt)
G.992.2 (G.lite)
G.992.3 (ADSL2, G.dmt.bit)
G.992.4 (ADSL2, G.lite.bis)
G.992.5 (ADSL2+)
G.993.1 (VDSL)
G.993.2 (VDSL2)
G.994.1 (G.hs)
G.Vectoring
Annex A, M and L
Annex B and J
VDSL Profile up to 30a supported
G.SHDSL-EFM
•
•
•
•
•
•
Support ITU-T G991.2/G.994.1 standards
Support ITU-T G.998.1 (G.bond)
TC-PAM line modulation 16,32,64 & 128
CO or CPE Mode
IEEE 802.3 2Base-TL (aka 802.3ah) compliant
Rate negotiating/manually rate adaptation configuration
2–8 wire mode auto detect
Data rate selections: Up to Nx239 (5.7 Mbps) per
pair
Support bonding based on EFM
Line interface: up to 4 pairs on a single RJ45 connector
(/2G and /4G models)
•
•
•
•
G.SHDSL-ATM
(/2G and /4G models)
WAN Interface (if applicable)
•
•
•
•
•
•
•
•
Classical IPoA (RFC 1577/2225)
PPPoE Client (over ATM) (RFC 2516)
IPoA (RFC 2684/1483)
ATM AAL5 encapsulation
Max. 8 PVCs
User selectable VC MUX and LLC MUX (default)
Configurable auto-connection
ATM QoS: UBR (default), CBR, and VBR-rt, VBRnrt, UBR: per VC queuing
• Auto-configuration: TR-037 & ILMI 4.0
48
SmartNode 4980 & 4990 User Manual
B • Specifications
Table 6. WAN Interface Specifications
Factor
Specs
Interworking/Interoperability
• G.SHDSL Interoperability:
- Alcatel
- NEC
- Lucent Anymedia
- Lucent Stinger
• BRAS Interoperability:
- Cisco
- Redback
- Alcatel-Lucent EVLT-K
- Calix E5-120
- Ericsson Telecom AB EDN612nm
- Adtran, Inc. IU VDSL48J3:ME
- Adtran, Inc. Adtran TA1248V
- Alcatel-Lucent ABLT-D
Fiber
(/F models)
• 100Mbps and 1000Mbps Fiber SFP.
(For a list of tested SFP modules, please refer to http:/
/www.patton.com/products/sfpmodules.asp)
Ethernet (ETH 0/2)
(/I models)
• 10/100Mbps Fast Ethernet R45
Identification of the SmartNode Devices via SNMP
All SmartNode devices have assigned sysObjectID (.iso.org.dod.internet.mgmt.mib-2.system.sysObjectID)
numbers (see Table 7).
Table 7. SmartNode Models and their Unique sysObjectID
SmartNode Model
SN4980/1E15V
SysObjectID
.iso.org.dod.internet.private.enterprises.patton.products.sn4970.1
1.3.6.1.4.1.1768.100.4.22.1
SN4980/1E24V
.iso.org.dod.internet.private.enterprises.patton.products.sn4970.2
1.3.6.1.4.1.1768.100.4.22.2
SN4980/1E30V
.iso.org.dod.internet.private.enterprises.patton.products.sn4970.3
1.3.6.1.4.1.1768.100.4.22.3
SN4980/4E15V
.iso.org.dod.internet.private.enterprises.patton.products.sn4970.4
1.3.6.1.4.1.1768.100.4.22.4
Identification of the SmartNode Devices via SNMP
49
SmartNode 4980 & 4990 User Manual
B • Specifications
Table 7. SmartNode Models and their Unique sysObjectID (Continued)
SmartNode Model
SN4980/4E24V
SysObjectID
.iso.org.dod.internet.private.enterprises.patton.products.sn4970.5
1.3.6.1.4.1.1768.100.4.22.5
SN4980/4E30V
.iso.org.dod.internet.private.enterprises.patton.products.sn4970.6
1.3.6.1.4.1.1768.100.4.22.6
SN4980/4E48V
.iso.org.dod.internet.private.enterprises.patton.products.sn4970.7
1.3.6.1.4.1.1768.100.4.22.7
SN4980/4E60V
.iso.org.dod.internet.private.enterprises.patton.products.sn4970.8
1.3.6.1.4.1.1768.100.4.22.8
SN4980/4E96V
.iso.org.dod.internet.private.enterprises.patton.products.sn4970.9
1.3.6.1.4.1.1768.100.4.22.9
SN4980/4E120V
.iso.org.dod.internet.private.enterprises.patton.products.sn4970.10
1.3.6.1.4.1.1768.100.4.22.10
SN4980/4E30V120R
.iso.org.dod.internet.private.enterprises.patton.products.sn4970.21
1.3.6.1.4.1.1768.100.4.22.21
SN4981/1E15V
.iso.org.dod.internet.private.enterprises.patton.products.sn4970.11
1.3.6.1.4.1.1768.100.4.22.11
SN4981/1E24V
.iso.org.dod.internet.private.enterprises.patton.products.sn4970.12
1.3.6.1.4.1.1768.100.4.22.12
SN4981/1E30V
.iso.org.dod.internet.private.enterprises.patton.products.sn4970.13
1.3.6.1.4.1.1768.100.4.22.13
SN4981/4E15VR
.iso.org.dod.internet.private.enterprises.patton.products.sn4970.14
1.3.6.1.4.1.1768.100.4.22.14
SN4981/4E24VR
.iso.org.dod.internet.private.enterprises.patton.products.sn4970.15
1.3.6.1.4.1.1768.100.4.22.15
SN4981/4E30VR
.iso.org.dod.internet.private.enterprises.patton.products.sn4970.16
1.3.6.1.4.1.1768.100.4.22.16
SN4981/4E48VR
.iso.org.dod.internet.private.enterprises.patton.products.sn4970.17
1.3.6.1.4.1.1768.100.4.22.17
SN4981/4E60VR
.iso.org.dod.internet.private.enterprises.patton.products.sn4970.18
1.3.6.1.4.1.1768.100.4.22.18
SN4981/4E96VR
.iso.org.dod.internet.private.enterprises.patton.products.sn4970.19
1.3.6.1.4.1.1768.100.4.22.19
SN4981/4E120VR
.iso.org.dod.internet.private.enterprises.patton.products.sn4970.20
1.3.6.1.4.1.1768.100.4.22.20
SN4981/4E30V120R
.iso.org.dod.internet.private.enterprises.patton.products.sn4970.22
1.3.6.1.4.1.1768.100.4.22.22
Identification of the SmartNode Devices via SNMP
50
SmartNode 4980 & 4990 User Manual
B • Specifications
Table 7. SmartNode Models and their Unique sysObjectID (Continued)
SmartNode Model
SN4991/1E15V
SysObjectID
.iso.org.dod.internet.private.enterprises.patton.products.sn4970.1
1.3.6.1.4.1.1768.100.4.22.11
SN4991/1E24V
.iso.org.dod.internet.private.enterprises.patton.products.sn4970.2
1.3.6.1.4.1.1768.100.4.22.12
SN4991/1E30V
.iso.org.dod.internet.private.enterprises.patton.products.sn4970.3
1.3.6.1.4.1.1768.100.4.22.13
SN4991/4E15VR
.iso.org.dod.internet.private.enterprises.patton.products.sn4970.4
1.3.6.1.4.1.1768.100.4.22.14
SN4991/4E24VR
.iso.org.dod.internet.private.enterprises.patton.products.sn4970.5
1.3.6.1.4.1.1768.100.4.22.15
SN4991/4E30VR
.iso.org.dod.internet.private.enterprises.patton.products.sn4970.6
1.3.6.1.4.1.1768.100.4.22.16
SN4991/4E48VR
.iso.org.dod.internet.private.enterprises.patton.products.sn4970.7
1.3.6.1.4.1.1768.100.4.22.17
SN4991/4E60VR
.iso.org.dod.internet.private.enterprises.patton.products.sn4970.8
1.3.6.1.4.1.1768.100.4.22.18
SN4991/4E96VR
.iso.org.dod.internet.private.enterprises.patton.products.sn4970.9
1.3.6.1.4.1.1768.100.4.22.19
SN4991/4E120VR
.iso.org.dod.internet.private.enterprises.patton.products.sn4970.10
1.3.6.1.4.1.1768.100.4.22.20
SN4991/4E30V120R
.iso.org.dod.internet.private.enterprises.patton.products.sn4970.21
1.3.6.1.4.1.1768.100.4.22.22
Note
The SysObjectIDs for the SN4991 G.SHDSL, ADSL, Fiber, X.21 and RJ45
Ethernet models are the same as the corresponding SN4991 models listed
above.
According to Table 7, an SNMP get request to .iso.org.dod.internet.mgmt.mib-2.system.sysObjectID of a SmartNode 4980/1E15V/EUI device reads out a numeric OID of 1.3.6.1.4.1.1768.100.4.22.1, which represents a
SmartNode 4980/1E15V/EUI device. The mapping of the sysObjectID to each of the SmartNode model is
realized with the SmartNode product identification MIB.
The SNMP agent running in SmartWare is SNMP version 1
(SNMPv1) compliant. SNMP version 2 (SNMPv2) and SNMP
version 3 (SNMPv3) are not currently supported.
Identification of the SmartNode Devices via SNMP
51
Appendix C Cabling
Chapter contents
Introduction ..........................................................................................................................................................53
Console .................................................................................................................................................................53
Ethernet ................................................................................................................................................................54
E1 PRI ..................................................................................................................................................................55
T1 PRI ..................................................................................................................................................................56
52
SmartNode 4980 & 4990 User Manual
C • Cabling
Introduction
This section provides information on the cables used to connect the SmartNode and the interface cards to the
existing network infrastructure and to third party products.
Console
The SmartNode can be connected to a serial terminal over its serial console port, as depicted in Figure 11.
The interconnecting cables shall be acceptable for external use
and shall be rated for the proper application with respect to voltage, current, anticipated temperature, flammability, and
mechanical serviceability.
0/3
0/2
0/1
T1
/E
1
0/0
ET
H
0/1
H
0/0
Reset
ET
Con
so
RS-
le
23
2
Serial Terminal
Note A Patton Model 16F-561 RJ45 to DB-9 adapter is included with
each SmartNode device.
Figure 11. Connecting a serial terminal
Note
Introduction
See section “Console Port” on page 58 for console port pin-outs.
53
SmartNode 4980 & 4990 User Manual
C • Cabling
Ethernet
Ethernet devices (10Base-T/100Base-T/1000Base-T) are connected to the SmartNode over a cable with RJ-45
plugs. All Ethernet ports on the SmartNode are Auto-MDX use any straight or crossover cable to connect to
hubs, switches, PCs or other devices
For the 3rd Ethernet port (ETH0/2), only figure 11 below applies. There is
no 1000Base-T (Gigabit) Ethernet support on (ETH0/2).
Note
The interconnecting cables shall be acceptable for external use
and shall be rated for the proper application with respect to voltage, current, anticipated temperature, flammability, and
mechanical serviceability.
0/3
0/2
0/1
T1
/E
0/0
1
ET
H
0/1
H
0/0
Reset
ET
Con
so
RS-
Hub
le
23
2
Straight-through cable
RJ-45, male
RJ-45, male
1
1
2
2
3
3
6
6
Note: Other pins are not used.
Figure 12. Typical Ethernet straight-through cable diagram for 10/100Base-T
RJ-45, male
RJ-45, male
1
1
2
2
3
3
6
6
4
4
5
5
7
7
8
8
Figure 13. Typical Ethernet straight-through cable diagram for 1000Base-T
Ethernet
54
SmartNode 4980 & 4990 User Manual
C • Cabling
E1 PRI
The E1 PRI is usually connected to a PBX or switch—local exchange (LE). Type and pin outs of these devices
vary depending on the manufacturer. In most cases, a straight-through RJ-45 to RJ-45 can be used to connect
the PRI with a PBX. A cross-over cable is required to connect to an NT device, as illustrated in figure 14.
Hazardous network voltages are present in the PRI cables. If
you detach the cable, detach the end away from the SmartNode or interface card first to avoid possible electric shock.
Network hazardous voltages may be present on the device
in the area of the PRI port, regardless of when power is
turned OFF.
To prevent damage to the system, make certain you connect
the PRI cable to the PRI port only and not to any other RJ-45
socket.
0/3
0/2
0/1
T1
/E
1
0/0
ET
H
0/1
H
0/0
Reset
ET
Co
ns
RS
NT
ole
-2
32
Cross-over cable
Figure 14. Connecting an E1 PRI port to an NT1
RJ-48C, male
RJ-48C, male
RX Ring
1
1
RX Ring
RX Tip
2
2
RX Tip
RX Shield
3
3
RX Shield
TX Ring
4
4
TX Ring
TX Tip
5
5
TX Tip
TX Shield
6
6
TX Shield
N/C
7
7
N/C
N/C
8
8
N/C
*N/C = No connection*
Figure 15. E1 PRI port crossover cable
E1 PRI
55
SmartNode 4980 & 4990 User Manual
C • Cabling
T1 PRI
The T1 PRI is usually connected to a PBX or switch—local exchange (LE). Type and pin outs of these devices
vary depending on the manufacturer. In most cases, a straight-through RJ-45 to RJ-45 can be used to connect
the PRI with a PBX. A cross-over cable is required to connect to an NT device, as illustrated in figure 16.
Hazardous network voltages are present in the PRI cables. If
you detach the cable, detach the end away from the SmartNode or interface card first to avoid possible electric shock.
Network hazardous voltages may be present on the device
in the area of the PRI port, regardless of when power is
turned OFF.
To prevent damage to the system, make certain you connect
the PRI cable to the PRI port only and not to any other RJ-45
socket.
0/3
0/2
0/1
T1
/E
0/0
1
ET
H
0/1
H
0/0
Reset
ET
Con
so
RS-
NT
le
23
2
Cross-over cable
Figure 16. Connecting a T1 PRI port to an NT device
RJ-45, male
RJ-45, male
RX Ring
1
1
RX Ring
RX Tip
2
2
RX Tip
RX Shield
3
3
RX Shield
TX Ring
4
4
TX Ring
TX Tip
5
5
TX Tip
TX Shield
6
6
TX Shield
N/C
7
7
N/C
N/C
8
8
N/C
*N/C = No connection*
Figure 17. T1 PRI crossover cable
T1 PRI
56
Appendix D Port Pin-outs
Chapter contents
Introduction ..........................................................................................................................................................58
Console Port..........................................................................................................................................................58
Ethernet ................................................................................................................................................................58
PRI Port ................................................................................................................................................................59
G.SHDSL ATM only port (2GS models only) ......................................................................................................59
G.SHDSL EFM & ATM port (/2G and /4G models)...........................................................................................59
ADSL & VDSL-ADSL Port (/A and /AVA & /AVB models only) ........................................................................60
Fiber Ports (/F models only) ..................................................................................................................................60
X.21 DB-15 Connector (/D models only) .............................................................................................................60
10/100 Fast Ethernet Port .....................................................................................................................................60
57
SmartNode 4980 & 4990 User Manual
D • Port Pin-outs
Introduction
This section provides pin-out information for the ports of the SmartNode.
Console Port
Configuration settings: 9600 bps, 8 bits, no parity, 1 stop bit, no flow control
8–RTS (N/C)
7–CTS (N/C)
6–TD
5–RD
4–SG
3–DTR
2–CD (N/C)
1–DSR
1 2 3 4 5 6 7 8
Pins 1 & 3 are
connected together
Figure 18. EIA-561 (RJ-45 8-pin) port
Note
N/C means no internal electrical connection.
Ethernet
Table 8. RJ45 socket 10/100Base-T
Note
Pin
Signal
1
TX+
2
TX-
3
RX+
6
RX-
Pins not listed are not used.
Table 9. RJ45 socket 1000Base-T
Introduction
Pin
Signal
1
TRD0+
2
TRD0-
3
TRD1+
6
TRD1-
4
TRD2+
5
TRD258
SmartNode 4980 & 4990 User Manual
D • Port Pin-outs
Table 9. RJ45 socket 1000Base-T (Continued)
Pin
Signal
7
TRD3+
8
TRD3-
PRI Port
Table 10. RJ-45 socket
Note
Pin
USR
1
RX Ring
2
RX Tip
3
RX Shield
4
TX Ring
5
TX Tip
6
TX Shield
Pins not listed are not used.
G.SHDSL ATM only port (2GS models only)
Table 11. RJ-45 connector
Note
Pin
Signal
3
Tip 2
4
Tip 1
5
Ring 1
6
Ring 2
Pins not listed are not used.
G.SHDSL EFM & ATM port (/2G and /4G models)
Table 12. EFM Port
PRI Port
Pin
Signal
Pair
1
Tip
1
2
Ring
1
3
Tip
2
4
Tip
0
5
Ring
0
6
Ring
2
7
Tip
3
8
Ring
3
59
SmartNode 4980 & 4990 User Manual
D • Port Pin-outs
ADSL & VDSL-ADSL Port (/A and /AVA & /AVB models only)
Table 13. ADSL & VDSL-ADSL Port: RJ-45 connector
Note
Pin
Signal
4
Tip
5
Ring
Pins not listed are not used
Fiber Ports (/F models only)
For tested and approved modules, please refer to the list of SFP’s Patton has tested at http://www.patton.com/
products/sfpmodules.asp
X.21 DB-15 Connector (/D models only)
10/100 Fast Ethernet Port
Note
Pin
Signal
1
TX+
2
TX-
3
RX+
6
RX-
Pins not listed are not used
ADSL & VDSL-ADSL Port (/A and /AVA & /AVB models only)
60
Appendix E SmartNode Factory Configuration
Chapter contents
Introduction ..........................................................................................................................................................62
61
SmartNode 4980 & 4990 User Manual
E • SmartNode Factory Configuration
Introduction
The factory configuration settings for the SmartNode 4980 and 4990 are as follows:
#----------------------------------------------------------------#
#
#
# Factory configuration file
#
#
#
#----------------------------------------------------------------#
dns-relay
timer PROVISIONING now + 1 minute "provisioning execute PF_PROVISIONING_CONFIG"
sntp-client
sntp-client server primary pool.ntp.org
profile provisioning PF_PROVISIONING_CONFIG
destination configuration
activation reload immediate
location 1 http://redirect.patton.com/
$(system.mac);mac=$(system.mac);serial=$(system.serial);hwMajor=$(system.hw.majo
r);hwMinor=$(system.hw.minor);swMajor=$(system.sw.major);swMinor=$(system.sw.min
or);swDate=$(system.sw.date);productName=$(system.product.name);cliMajor=$(cli.m
ajor);cliMinor=$(cli.minor);osName=$(cli.major>=4|Trinity|SmartWare);subDirTrinity=$(cli.major>=4|/Trinity);subDirSmartWare=$(cli.major<4|/SmartWare);dhcp66=$(dhcp.66);dhcp67=$(dhcp.67)
location 2 $(dhcp.66)
location 3 $(dhcp.66)/$(system.mac).cfg
location 4 http://$(dhcp.66)/$(dhcp.67)
location 5 http://$(dhcp.66)/$(system.mac).cfg
location 6 tftp://$(dhcp.66)/$(dhcp.67)
location 7 tftp://$(dhcp.66)/$(system.mac).cfg
system
ic voice 0
profile napt NAPT_WAN
Introduction
62
SmartNode 4980 & 4990 User Manual
E • SmartNode Factory Configuration
profile dhcp-server DHCPS_LAN
network 192.168.1.0 255.255.255.0
include 1 192.168.1.10 192.168.1.99
lease 2 hours
default-router 1 192.168.1.1
domain-name-server 1 192.168.1.1
context ip router
interface WAN
ipaddress dhcp
use profile napt NAPT_WAN
tcp adjust-mss rx mtu
tcp adjust-mss tx mtu
interface LAN
ipaddress 192.168.1.1 255.255.255.0
tcp adjust-mss rx mtu
tcp adjust-mss tx mtu
context ip router
dhcp-server use DHCPS_LAN
port ethernet 0 0
medium auto
encapsulation ip
bind interface WAN router
Introduction
63
SmartNode 4980 & 4990 User Manual
E • SmartNode Factory Configuration
no shutdown
port ethernet 0 1
medium auto
encapsulation ip
bind interface LAN router
no shutdown
Introduction
64
Appendix F End User License Agreement
Chapter contents
End User License Agreement .................................................................................................................................66
1. Definitions ..................................................................................................................................................66
2. Title ............................................................................................................................................................66
3. Term ...........................................................................................................................................................66
4. Grant of License ..........................................................................................................................................66
5. Warranty ....................................................................................................................................................66
6. Termination ................................................................................................................................................67
7. Other licenses .............................................................................................................................................67
8. SmartWare licenses .....................................................................................................................................67
65
SmartNode 4980 & 4990 User Manual
F • End User License Agreement
End User License Agreement
By opening this package, operating the Designated Equipment or downloading the Program(s) electronically,
the End User agrees to the following conditions:
1. Definitions
A) Effective Date shall mean the earliest date of purchase or download of a product containing the Patton
Electronics Company Program(s) or the Program(s) themselves.
B)
Program(s) shall mean all software, software documentation, source code, object code, or executable code.
C)
End User shall mean the person or organization which has valid title to the Designated Equipment.
D) Designated Equipment shall mean the hardware on which the Program(s) have been designed and provided
to operate by Patton Electronics Company.
2. Title
Title to the Program(s), all copies of the Program(s), all patent rights, copyrights, trade secrets and proprietary
information in the Program(s), worldwide, remains with Patton Electronics Company or its licensors.
3. Term
The term of this Agreement is from the Effective Date until title of the Designated Equipment is transferred by
End User or unless the license is terminated earlier as defined in section “6. Termination” on page 67.
4. Grant of License
A) During the term of this Agreement, Patton Electronics Company grants a personal, non-transferable,
non-assignable and non-exclusive license to the End User to use the Program(s) only with the Designated
Equipment at a site owned or leased by the End User.
B)
The End User may copy licensed Program(s) as necessary for backup purposes only for use with the Designated Equipment that was first purchased or used or its temporary or permanent replacement.
C)
The End User is prohibited from disassembling; decompiling, reverse-engineering or otherwise attempting to discover or disclose the Program(s), source code, methods or concepts embodied in the Program(s)
or having the same done by another party.
D) Should End User transfer title of the Designated Equipment to a third party after entering into this
license agreement, End User is obligated to inform the third party in writing that a separate End User
License Agreement from Patton Electronics Company is required to operate the Designated Equipment.
5. Warranty
The Program(s) are provided as is without warranty of any kind. Patton Electronics Company and its licensors
disclaim all warranties, either express or implied, including but not limited to the implied warranties of merchantability, fitness for a particular purpose or non-infringement. In no event shall Patton Electronics Company or its licensors be liable for any damages whatsoever (including, without limitation, damages for loss of
business profits, business interruption, loss of business information, or other pecuniary loss) arising out of the
use of or inability to use the Program(s), even if Patton Electronics Company has been advised of the possibility
of such damages. Because some states do not allow the exclusion or limitation of liability for consequential or
incidental damages, the above limitation may not apply to you.
End User License Agreement
66
SmartNode 4980 & 4990 User Manual
F • End User License Agreement
If the Program(s) are acquired by or on behalf of a unit or agency of the United States Government, the Government agrees that such Program(s) are commercial computer software or computer software documentation and
that, absent a written agreement to the contrary, the Government’s rights with respect to such Program(s) are
limited by the terms of this Agreement, pursuant to Federal Acquisition Regulations 12.212(a) and/or DEARS
227.7202-1(a) and/or sub-paragraphs (a) through (d) of the “Commercial Computer Software - Restricted
Rights” clause at 48 C.F.R. 52.227-19 of the Federal Acquisition Regulations as applicable.
6. Termination
A) The End User may terminate this agreement by returning the Designated Equipment and destroying all
copies of the licensed Program(s).
B)
Patton Electronics Company may terminate this Agreement should End User violate any of the provisions
of section “4. Grant of License” on page 66.
C)
Upon termination for A or B above or the end of the Term, End User is required to destroy all copies of
the licensed Program(s)
7. Other licenses
The Program may be subject to licenses extended by third parties. Accordingly, Patton Electronics Company
licenses the Programs subject to the terms and conditions dictated by third parties. Third party software identified to the Programs includes:
• The LGPL (Lesser General Public License) open source license distributed to you pursuant to the LGPL
license terms (http://www.gnu.org/licenses/lgpl.html).
8. SmartWare licenses
• A routing license is included at no charge.
• MGCP and VPN capabilities will require the purchase of an additional license.
RedBoot (Red Hat Embedded Debug and Bootstrap) embedded system debug/bootstrap environment from
Red Hat distributed to you pursuant to the eCos license terms (http://ecos.sourceware.org/licenseoverview.html) and GNU General Public License (GPL) terms (http://www.gnu.org/copyleft/gpl.html).
Source code is available upon request.
End User License Agreement
67
Download PDF
Similar pages