Ethernet over Copper Transmission Extenders
Ethernet Transmission over Coaxial or UTP Cable
Fiber Optic and Ethernet Network Solutions
Ethernet over Copper
CopperLine® is an advanced and unique technology that extends Ethernet networks beyond
the 100-meter limitation encountered when using UTP for IP Video and Ethernet-based
applications. CopperLine® is a cost-saving alternative that enables you to use existing coaxial
and UTP cables for significantly greater Ethernet transmission distances.
Choose CopperLine®:
• Longest Available Transmission Distances
• Fixed Data at Maximum Specified Distance
• All CLFE(X)EOC Coax and CLFE(X)EOU UTP
Models Support Pass-Through PoE
• Consumes Less than 1 Watt per Port
• All CL(L,R)FE(X)POEC and CL(L,R)FE(X)POEU
Models Support PoE+ Power Injection and
Pass-Through Power
• Price and Performance – CopperLine®
CopperLine® Features
• Extends Ethernet Networks beyond 100 m
limitations for CCTV and IT projects
• Cost-effective
• Extends standard Ethernet:
»»10BaseT up to 3,000 ft (914 m) and
100BaseT up to 2,000 ft (610 m) over UTP
»»10BaseT up to 5,000 ft (1,524 m) and
100BaseT up to 2,000 ft (610 m) over Coax
• Switch-selectable LAN rate optimizes the
best possible rate/distance design for each
application
• High data rate – ideal for high bandwidth
requirements of Mega-pixel cameras or
multiple IP cameras
AGENCY COMPLIANCE
2
• Compatible with any LAN device –
fully transparent to Ethernet networks and
higher layer protocols
• Easy to install – no IP address programming
or other networking setup required
• Indicating LEDs for link status and data rate
• Very low power – remote units can share
power supply with camera
• Now form- and fit-compatible with all
ComNet Products
• Lifetime Warranty
• Designed and made in the USA using a unique
state-of-the-art data transmission technology
www.comnet.net
Ethernet-over-Copper Extender with Pass-Through PoE
The ComNet™ CopperLine® Ethernet over copper line supports
up to sixteen channels of 10/100Mbps Ethernet with Pass-through
PoE over twisted pair cable (CAT-5, UTP), or over coaxial cable.
The single channel units may be powered by a PoE switch or
the included power supply. Four, eight, and sixteen channel
units operate from local power. These units provide the ultimate
flexibility for extending a powered device (PD) over long distance
copper. DIP switches are provided for user-selection of local or
remote, 10 or 100Mbps, and 1 pair or 4 pair (UTP) settings.
PoE Pass-Through Mode
CAT-5 Cable
Extended Distance
Ethernet + PoE
PoE Switch
CNGE2FE24MSPOE
CLFE1EOC
CLFE1EOC
PoE Camera
CLFE1EOU Units
PoE Cameras
CLFE1EOC
with 12 VDC / 24 VAC
Local Power
IP Camera
PoE Pass-Through Mode with Multiple Remote Units
PoE Switch
CNGE2FE24MSPOE
CLFE4EOU
with 12 VDC
Local Power
Non-PoE Mode
Switch
CNGE2FE24MS
CLFE1EOC
with 12 VDC / 24 VAC
Local Power
CopperLine® Ethernet over Unshielded Twisted Pair (UTP)
Model
Ports
Function
CLFE1EOU
1
1 channel Ethernet over UTP with Pass-through PoE
CLFE4EOU
4
4 channel Ethernet over UTP with Pass-through PoE
CLFE8EOU
8
8 channel Ethernet over UTP with Pass-through PoE
CLFE16EOU
16
16 channel Ethernet over UTP with Pass-through PoE
CopperLine® Ethernet over Coaxial Cable
Model
Ports
Function
CLFE1EOC
1
1 channel Ethernet over Coaxial Cable with Pass-through PoE
CLFE4EOC
4
4 channel Ethernet over Coaxial Cable with Pass-through PoE
CLFE8EOC
8
8 channel Ethernet over Coaxial Cable with Pass-through PoE
CLFE16EOC
16
16 channel Ethernet over Coaxial Cable with Pass-through PoE
3
Ethernet-over-Copper Extender With 30 Watt PSE PoE+
The all-new ComNet™ CopperLine® Ethernet over copper line has
a completely new look and is now form and fit compatible with all
ComNet products. With a greater focus on providing PoE power
to devices on the network, the CL(L,R)FE(X)POE(C,U) line can act
as power sourcing equipment (PSE) or pass through power from
a different source. Available in single, four, eight and sixteen
port models, the CL(L,R)FE(X)POE(C,U) line can transmit 10/100Mbps Ethernet with PoE+ Power Injection and Passthrough PoE+ over twisted pair cable (CAT-5, UTP) or over coax. You can connect this series directly to a PoE+ switch,
or it can source PoE+ power with a 48 to 56 Volt input to either the Local or Remote ends. The CL(L,R)FE(X)POE(C,U)
line can provide great flexibility for extending the distance of a powered device over longer copper media distances.
PoE Pass-Through Mode with Multiple Remote Units
CAT-5 Cable
Extended Distance
Ethernet + PoE
PoE Switch
CNGE2FE24MSPOE
CLLFE4POEC
with 12 VDC
Local Power
Local PoE Injection Mode
Switch
CNGE2FE24MS
CLLFE1POEU
with 48 to 56 VDC
Local Power
Remote PoE Injection Mode
Switch
CNGE2FE24MS
CLLFE1POEU
with 12 VDC
Local Power
CLRFE1POEC Units
PoE Cameras
CLRFE1POEU
PoE Camera
CLRFE1POEU
with 48 to 56 VDC
Local Power
PoE Camera
CopperLine® Ethernet over Unshielded Twisted Pair (UTP) with PSE PoE and Pass-through PoE
Local Model
Remote Model
Function
CLLFE1POEU
CLRFE1POEU
1 channel Ethernet over UTP with Pass-through PoE and PSE PoE
CLLFE4POEU
CLRFE4POEU
4 channel Ethernet over UTP with Pass-through PoE and PSE PoE
CLLFE8POEU
n/a
8 channel Ethernet over UTP with Pass-through PoE and PSE PoE
CLLFE16POEU
n/a
16 channel Ethernet over UTP with Pass-through PoE and PSE PoE
CopperLine® Ethernet over Coaxial Cable with PSE PoE and Pass-through PoE
4
Local Model
Remote Model
Function
CLLFE1POEC
CLRFE1POEC
1 channel Ethernet over Coaxial Cable with Pass-through PoE and PSE PoE
CLLFE4POEC
CLRFE4POEC
4 channel Ethernet over Coaxial Cable with Pass-through PoE and PSE PoE
CLLFE8POEC
n/a
8 channel Ethernet over Coaxial Cable with Pass-through PoE and PSE PoE
CLLFE16POEC
n/a
16 channel Ethernet over Coaxial Cable with Pass-through PoE and PSE PoE
www.comnet.net
10/100 Mbps 4+1 Ethernet Self-Managed Switches with 30 Watt Power over Ethernet (PoE+)
The all-new ComNet™ CLFE4+1SMS[POE](C,U) is a five-port Ethernet over coaxial
cable/UTP self-managed switch with uplink management functionality and features
four copper ports operating at 10/100 Mbps and is designed to combine four electrical
ports into a single electrical CAT-5, UTP or coax CopperLine® port that forwards this
data to the next network device. No programming required to use this product. The
ComNet CLFE4+1SMS comes pre-programmed; preventing network video flooding
with DIP switch selection of the fifth electrical port as uplink or as an unmanaged switch.
When paired with a 48 to 56 VDC power supply, Ports 1–4 of the CLFE4+1SMSPOE can
supply up to thirty watts of PoE to each port and incorporate PoE+ features based on the
IEEE 802.3at standard.
Typical PoE Application
CAT-5 Cable
Extended Distance
Ethernet + PoE
Switch
CNGE2FE24MS
CLFE1EOU
with 12 VDC / 24 VAC
Local Power
CLFE4+1SMSPOEU
with 48 to 56 VDC*
PoE Cameras
* For non-PoE applications, use the
CLFE4+1SMS(C,U) with a 12 VDC Power Supply
CopperLine® Self-Managed Switch – Ethernet over Unshielded Twisted Pair (UTP)
Model
Function
CLFE4+1SMSU
4 Port 10/100 Mbps Ethernet Self-Managed Switch, UTP CopperLine® Uplink Port
CLFE4+1SMSPOEU
4 Port 10/100 Mbps Ethernet Self-Managed Switch, PoE+, UTP CopperLine® Uplink Port
CopperLine® Self-Managed Switch – Ethernet over Coaxial Cable
Model
Function
CLFE4+1SMSC
4 Port 10/100 Mbps Ethernet Self-Managed Switch, Coaxial CopperLine® Uplink Port
CLFE4+1SMSPOEC
4 Port 10/100 Mbps Ethernet Self-Managed Switch, PoE+, Coaxial CopperLine® Uplink Port
Ethernet-over-Copper Extender With Pass-Through PoE
CLFE(X)EO(C,U)
HARDENED
INSTALLATION AND
OPERATION MANUAL
EXTENDER
C,U) Series30W PSE POE+
CL(L,R)FE(X)POE(
R WITH
OPPER EXTENDE
Complete Product Documentation
PASS-THRU
INSTALLATION
The ComNet™ CopperLine® Ethernet over copper line supports up to sixteen
channels of 10/100Mbps Ethernet with Pass-through PoE over twisted pair
cable (CAT-5, UTP), or over coaxial cable. The single channel units may be
powered by a PoE switch or the included power supply. Four, eight, and
sixteen channel units operate from local power. These units provide the
ultimate flexibility for extending a powered device (PD) over long distance
copper. DIP switches are provided for user-selection of local or remote, 10 or
100Mbps, and 1 pair or 4 pair (UTP) settings.
AND OPERATION
MANUAL
CLSETUP
IP CAmERA SETUP
ANd POE TESTER
ETHERNET-OVER-C
the following
This manual serves
Numbers:
ComNet Model
CLLFE1POEC
CLRFE1POEC
CLLFE1POEU
CLRFE1POEU
CLLFE4POEC
CLRFE4POEC
CLLFE4POEU
CLRFE4POEU
CLLFE8POEC
CLLFE8POEU
CLLFE16POEC
CLLFE16POEU
to sixteen channels
line supports up
® Ethernet over copper
™
h PoE+ over
The ComNet CopperLine
Injection and Pass-throug
to a
with PoE+ Power
to connect directly
of 10/100Mbps Ethernet
coax. With the ability
to either
(CAT-5, UTP) or over
a 48 to 56 V input
twisted pair cable
PoE+ power with
a
ability to generate
flexibility for extending FEATURES
PoE+ switch, or the
provide the ultimate
both a Local › Transmits individual Ethernet data channels with Passends, these units
the Local or Remote
A complete set includes
copper.
distance
include one through PoE over standard UTP or Coaxial cable
over long
package sizes that
powered device (PD)
available in small
as a › Extends Ethernet up to 3,000 feet (914 m) at 10 Mbps or
Remote units are
packages as well
same
the
2,000 feet (610 m) at 100 Mbps over UTP cable
in
and Remote module.
are available
and Local modules
› Extends Ethernet up to 5,000 feet (1,524 m) at 10 Mbps or
or four channels,
2,000 feet (610m) at 100 Mbps over Coaxial cable
channel counts.
larger
for
rack
1RU
ascertaining equipment › Extended temperature operation from -40°C to +75°C
provided for rapidly
each light on › Extended Pass-through PoE meets the IEEE 802.3af
) LED indicators are
LED indicators for
Bi-color (Red/Green
11 describes the
standard for Power over Ethernet
Table 2 on Page
operating status.
› Full 10/100 Mbps Bandwidth
the unit.
units. The › Supports Multicast, Unicast and Jumbo Frame
are 1RU rack mountable
and CLLFE16POE(C,U)
or card mount› Symmetric Bandwidth provides consistent upload and
The CLLFE8POE(C,U)
able between stand-alone
model download with virtually zero packet loss over the total
units are interchange
addition of ComNet
CL(L,R)FE4POE(C,U)
mounted by the
, usable distance
may be DIN-rail
units are stand-alone› Type tested to RFC-2544 TCP/IP network bandwidth packet
configurations, or
CL(L,R)FE1POE(C,U)
adaptor.transmission standards
adaptor plate. The
model DINBKT4
DINBKT1 or DINBKT4
addition of ComNet
› User-selectable data rate for maximum bandwidth and
mounted by the
s.
or may be DIN-rail
mounting instruction
transmission distance utilization
C on Page 14 for
See Figures A through
Important Safety
Read and keep these
directions
Heed all warnings
Warning:
Follow all instructions
do not use this apparatus
near water
Clean only
with a dry cloth
› Complies with all major IEEE standards and RFC network
Install in accordance
protocols for UDP, TCP/IP, HTTP/HTTPs
with
instructions
the manufacture
r’s
The ComNet™ CopperLine
CLSETUP provides
a simple way to setup
powered IP cameras,
and focus PoEand is an ideal diagnostic
tool for installers
CCTV and IT PoE-based
working with both
systems. The CLSETUP
is compatible with
IEEE 802.3at PoE
IEEE 802.3af and
standards up to 30W.
See Figures 1 –
3 for complete installation
details.
› Tested and certified by an independent laboratory for full
This installation should
compliance with the environmental requirements (ambient
be made by a qualified
service person and
operating temperature, mechanical shock, vibration, humidity
should conform to
all local codes
with condensation, high-line/low-line voltage conditions
See further safety
instructions on
and transient voltage protection) of NEMA TS-1/TS-2 and
Page 3
CALTRANS Traffic Signal Control Equipment Specifications.
The complete CopperLine® product line
is listed on ComNet’s website, along with
data sheets and intruction manuals.
Scan this QR Code or visit:
› Designed and manufactured in the USA
› LED status indicators confirm operating status
› Available in small-size, ComFit interchangeable stand
alone or 1RU high rack mounted models
› Lifetime warranty
APPLICATIONS
› Retrofit existing analog CCTV installations to Ethernetbased systems
http://www.comnet.net/comnet-products/copperline/
› CCTV systems for casinos, airports, school campuses
LIFETIME WARRANTY WWW.COMNET.NET TECH SUPPORT: 1.888.678.9427
PAGE 1
E(C,U)_REV– 10/27/11
INS_CL(L,R)FE(X)PO
TECH SUPPORT:
1.888.678.9427
INS_CLSETUP_REV
–
12/18/11
PAGE 1
5
Mini Ethernet-over-Coax Extender Remote Units Powered by External or PoE Source
These Ethernet-over-coax minis are an ultra-small form factor addition to
the ComNet™ CopperLine® product family. These miniature remote units
provide 10/100 Mbps Ethernet data with or without Pass-through PoE power
over extended distance coaxial cable. Available in both standard and PoE
applications, the mini CopperLine® CLRFE1EOC/M units will allow extended
distance over copper to be used in applications where space is extremely
limited. Automatically configured as remote units, and with user configurable
selection of 10 Mbps or 100 Mbps speed these units are simple to install and
fully compatible with the entire CopperLine® product line.
PoE Pass-Through Mode
CAT-5 Cable
Extended Distance
Ethernet + PoE
PoE Switch
CNGE2FE24MSPOE
CLFE1EOC
CLRFE1EOCP/M
PoE Camera
CLRFE1EOCP/M Units
PoE Cameras
CLRFE1EOCE/M
with 12 VDC / 24 VAC
Local Power
IP Camera
PoE Pass-Through Mode with Multiple Remote Units
PoE Switch
CNGE2FE24MSPOE
CLFE4EOC
with 12 VDC
Local Power
Non-PoE Mode
Switch
CNGE2FE24MS
CLFE1EOC
with 12 VDC / 24 VAC
Local Power
CopperLine® Mini Ethernet-over-Coax Extender Remote Units
Model
Function
CLRFE1EOCE/M Miniature CopperLine® Single Channel Ethernet over Coax External Power, Remote
CLRFE1EOCP/M Miniature CopperLine® Single Channel Ethernet over Coax PoE Powered, Remote
All Eyes on CopperLine®
Now playing on ComNetTV: ComNet’s North America
Trainer introduces the all-new CopperLine® products.
Scan this QR Code to visit http://youtu.be/6FQ9IZtgzIA
6
www.comnet.net
Small Form-Factor Pluggable Copper Range Extender Modules
The ComNet™ CopperLine® CL-SFP is a small form-factor pluggable Ethernet
extender module that improves bandwidth and distance of existing copper
networks. It helps avoid installation costs of new fiber lines on site by allowing
full 10 Mbps or 100 Mbps Ethernet bandwidth to be extended over 2-wire
twisted pair or coaxial cable.
Housed in a small form-factor pluggable (SFP) module enclosure, it is designed
for plug-and-play installation into any 100BASE-FX Ethernet unit with an MSAcompliant port. These must be used in pairs, with a CL-SFP module installed at
both ends of the connection, or a CopperLine® unit installed at one end.
Model
Function
CL-SFP1
10 Mbps Copper Range Extending SFP
CL-SFP3
100 Mbps Copper Range Extending SFP
CAT-5 Cable
Extended Distance
Switch
CNGE2FE24MS
CL-SFP(X)
Installed into SFP Port
CL-SFP(X)
Installed into SFP Port
Switch
CNGE2FE24MS
Switch
CNGE2FE24MS
CL-SFP(X)
Installed into SFP Port
CopperLine® Extender
Switch
CNGE2FE24MS
CopperLine® High-Power Mid-Span Injector
Model
Function
CLFE8IPS
8 Port, High Power PoE Midspan Injector, 37 Watts Per Port
CLFE16IPS
16 Port, High Power PoE Midspan Injector, 37 Watts Per Port
CopperLine® Managed High Power Midspan
Switch
CNGE2FE24MS
PoE Cameras
CLFE1EOC
CLFE1EOC
CLFE1EOC
CLFE1EOC
CLLFE1POEU
CLRFE1POEU
CLLFE1POEU
CLRFE1POEU
CLFE16IPS
CAT-5 Cable
Extended Distance
Ethernet + PoE
CopperLine® Accessories
Model
Function
CLSETUP
IP Camera Setup and PoE Tester
CL-ESP
Single Port Ethernet Voltage Transient & Surge Protector
CLRJ2COAX
RJ-45 Plug-to-Coax (BNC) – for use with CL-SFP(X) only
CLRJ2COAXCAB RJ-45 Plug-to-Coax (BNC) Cable Assembly – for use with CL-SFP(X) only
7
Design Assistance
Delighting the Customer
The ComNet Technical Support and
Design Center provides pre-sale
and post-sale support for Ethernet
transmission network and fiber optic
system design. The department
is staffed by some of the most
highly experienced, regarded and
recognized experts in the industry.
Our direct Design Center phone
number is 1-888-678-9427 or you
can call 1-203-796-5300 in the US
or +44 (0)113 307 6409 throughout
Europe and ask for the Design
Center, or contact us by Email at
designcenter@comnet.net
ComNet’s Customer Care Center is
here to provide solutions. Staffed
by experienced, knowledgeable,
and courteous representatives,
the ComNet Customer Care team
is there to help. Customer Care
representatives are available to
answer your questions concerning
pricing, product availability, order
status, shipping dates, returns,
warranty claims and so much more.
Lifetime Warranty
We’re so confident in the long-term
reliability of our products, we back
them with a no-questions asked
Lifetime Warranty.
Product Training and Education
ComNet offers a full curriculum of
fiber optic and Ethernet product
training designed to educate you
to make the right choices when
selecting transmission equipment
for your projects. Available online or in-person, ComNet training
qualifies for CEU credit.
3 CORPORATE DRIVE | DANBURY, CT 06810 | USA
T: 1 (203) 796-5300 | F: 1 (203) 796-5303
TECH SUPPORT: 1 (888) 678-9427
INFO@COMNET.NET
www.comnet.net
8 TURNBERRY PARK ROAD
GILDERSOME | MORLEY | LEEDS, UK LS27 7LE
T: +44 (0)113 307 6400
F: +44 (0)113 253 7462
INFO-EUROPE@COMNET.NET
© 2015 Communication Networks. All Rights Reserved.
“ComNet,” the “ComNet Logo,” “CopperLine,” and the
“CopperLine Logo” are trademarks of Communication
Networks.
ComNetB7 Rev3 – 03.15
Travel light!
This brochure and other ComNet product literature is available online.
Scan this QR Code with your mobile device, or visit the literature section
at www.comnet.net
Download PDF
Similar pages