EPSON EasyMP Network Projection Ver.2.75 Operation

EasyMP Network Projection Operation Guide
Contents
2
Before Use
Functions of EasyMP Network Projection . . . . . . . . . . . . . . . . . . . . . 5
Sharing the Projector . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
Various Screen Transfer Functions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
Installing the Software . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
Software Requirements . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
Installing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
Two Connection Modes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
Advanced Connection Mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
Quick Connection Mode (Only when the optional Wireless LAN unit is installed)
........................................................... 9
Steps for Connecting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
Preparing to Connect . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11
Connecting to a Projector on a Network and Projecting . . . . . . . 12
.
.
.
.
.
.
.
.
.
.
.
.
Connecting to a Projector on a Different Subnet . . . . . . . . . . . . . . 29
Specifying Either an IP Address or Projector Name and Performing a Search
(Advanced Connection Mode Only) . . . . . . . . . . . . . . . . . . . . . . . . . . .
Performing a Search with a Profile . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Making a Profile . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Searching by specifying a Profile . . . . . . . . . . . . . . . . . . . . . . . . . . .
Managing a Profile . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
29
30
30
31
32
Using Set options . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 34
EasyMP Network Projection Summary
Operating the Projector . . . . . . . . . . . . . . . . . . . . . .
Operating the Computer . . . . . . . . . . . . . . . . . . . . .
Using the Connection Screen . . . . . . . . . . . . . . . . . .
Using the Toolbar . . . . . . . . . . . . . . . . . . . . . . . . . .
Adjusting the Virtual Display . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22
Allocating the Image to be Projected . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26
Projecting the Allocated Images . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
12
12
13
15
Functions and Settings for EasyMP Network Projection
Projecting Only a PowerPoint Slide Show (Presentation Mode)
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19
Using Multi-Screen Display . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20
Example of Adjusting the Virtual Display . . . . . . . . . . . . . . . . . . . . . . . . . . .
Procedure Before Using the Multi-screen Display Function . . . . . . . . . . . . . .
Setting the Virtual Display . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Enable the virtual display driver (Windows only) . . . . . . . . . . . . . . . . . . .
.
.
.
.
.
.
.
.
.
.
.
.
21
21
22
22
Setting Each Item . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
General settings tab . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Adjust performance tab . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Audio Output tab . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
34
34
35
35
Appendix
Connection Limitations . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 37
Supported Resolutions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Display Color . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Number of Connections . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Others . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
When Using Windows Vista or Windows 7 . . . . . . . . . . . . . . . . . . .
Limitations when projecting from Windows Photo Gallery . . . . . .
Limitations in Windows Aero . . . . . . . . . . . . . . . . . . . . . . . . . .
Limitations when projecting from Windows Media Center . . . . . .
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
37
37
37
37
37
37
38
38
Troubleshooting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 39
Problems Concerning Network Functions . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Cannot connect to the projector. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
When a connection is made using EasyMP Network Projection, the projected
image remains as it is, and a connection cannot be made from another computer.
...... .. ..... ...... ..... .. ...... ..... ....... ...... ..... .
The projector is not found when EasyMP Network Projection is started. . . . . . . .
Cannot connect in Advanced Connection Mode or Wired LAN connection . . . . .
40
40
40
40
41
Contents
The Slide Show cannot be displayed on the desired display when the multi-screen
display function is being executed. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Applications are no longer displayed from the computer screen when the multiscreen display function is executed. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
The mouse cursor is not displayed on the computer screen. . . . . . . . . . . . . . . .
When connecting with EasyMP Network Projection the image is not displayed or
the image is slow to appear. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
When a connection is made using EasyMP Network Projection, a PowerPoint Slide
Show cannot be started. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
When a connection has been made using EasyMP Network Projection, the screen
will not be refreshed when using an Office application. . . . . . . . . . . . . . . . . . .
Error message when starting up EasyMP Network Projection . . . . . . . . . . . . . .
Network settings are not restored after cutting the connection to the computer
with EasyMP Network Projection. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
3
42
42
42
42
43
43
43
45
Glossary . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 46
General Notes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 47
About Notations . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 47
General Notice: . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 47
Index . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 48
Before Use
This guide describes useful functions for EasyMP Network Projection and how to install the software.
Functions of EasyMP Network Projection
You can use EasyMP Network Projection to project your computer screen
from the projector via a network. Sharing the projector over the network
and using various screen transfer functions allow you to hold effective
meetings and presentations.
5
• Presentation Mode s p.19
This function can project a PowerPoint Slide Show running on a
computer. You can give stylish presentations by projecting a black screen
while making preparations and so on, and when not performing a Slide
Show.
• Distribution function
The screen being displayed by a remote computer can be simultaneously
displayed by up to four projectors on the same network.
• Switching function
By using the meeting switching function, if EasyMP Network Projection is
installed on all of the computers, the presenters can take turns and project
their own images without changing cables.
Sharing the Projector
If the projector is connected to a network, you can share the projector from
computers on the network. When projecting data from different computers
during a meeting or presentation, you can progress smoothly without
changing the signal cable between each computer.
Even a distance between the projector and the computer does not cause any
problems.
Various Screen Transfer Functions
You can use the following screen transfer functions.
• Multi-screen display s p.20
You can project different images from up to four projectors from one
computer, allowing you to project landscape images such as spreadsheets
and so on as one continuous image.
Installing the Software
You can find EasyMP Network Projection on the EPSON Projector
Software CD-ROM. Install the software on the computer you are using.
Software Requirements
6
Display
*
Resolution of no less than XGA (1024x768) and
no higher than UXGA (1600x1200)
Display color of 16-bit color or greater (approx.
32000 display colors)
Operation is not guaranteed in Mac OS X 10.5.0 because the Firewall settings
are not set correctly when the version is updated.
EasyMP Network Projection runs on computers that meet the following
requirements.
OS
Windows 2000 Service Pack 4
The following 32 bit OS versions:
Windows XP
Windows XP Service Pack 1 or later
Windows Vista
Windows Vista Service Pack 1 or later
Windows 7
The following 64 bit OS versions:
Windows 7
Mac OS X 10.3.x
Mac OS X 10.4.x
Mac OS X 10.5.1 or later*
Mac OS X 10.6.x
Recommended: Mac OS X 10.3.9/10.4.11/10.5.8
CPU
Mobile Pentium III 1.2GHz or faster
Power PC G3 900MHz or faster
Recommended: Pentium M 1.6GHz or faster
CoreDuo 1.83GHz or faster
Amount of Memory
256MB or more
Recommended: 512MB or more
Hard Disk
Free Space
20MB or more
Installing
Make sure you check the following points before starting installation.
• When using a computer running any of the following operating systems,
you must have administrator authority to install EasyMP Network
Projection.
• Windows 2000
• Windows XP
• Windows Vista
• Windows 7
• Make sure that you close all running applications before starting
installation.
• When the language selected for the installation varies from that of the
OS being used, the screens may not be displayed correctly.
• You can download the latest version of EasyMP Network Projection
from the following Web site.
http://www.epson.com/
Installing the Software
q
For EMP NS Connection users
The EMP NS Connection name has changed.
Before change: EMP NS Connection
After change: EasyMP Network Projection
When using the same function as EMP NS Connection on the
projector, install EasyMP Network Projection after uninstalling EMP
NS Connection. You cannot connect to the projector correctly using
EMP NS Connection.
Procedure
7
C Double-click the "EMP_NPInstaller.mpkg" icon in the EPSON
window.
Installation starts.
D Follow the on-screen instructions to install.
q
Uninstalling
For Windows
Select Start - Settings - Control Panel - Add-Remove Programs or
Add or Remove Programs and then remove EasyMP Network
Projection.
For Mac OS
For Windows
A Turn on your computer.
B Insert the EPSON Projector Software CD-ROM into the
computer.
The installer starts automatically.
q
If the installer does not start automatically, double-click the CD-ROM
drive from My Computer (or Computer).
C Follow the on-screen instructions to install.
For Mac OS
A Turn on your computer.
B Insert the EPSON Projector Software CD-ROM into the
computer.
Double-click "EasyMP Network Projection Uninstaller.app" from the
EasyMP Network Projection folder to uninstall EasyMP Network
Projection.
EasyMP Network Projection Summary
This chapter explains how to connect the computer and the projector via a network, and the procedure for projecting images from your computer's screen with
the projector.
Two Connection Modes
9
There are two methods of connecting a computer and the projector via a
network by using EasyMP Network Projection.
Advanced Connection Mode
Advanced Connection Mode is an infrastructure connection, and connects
to an existing network system via a network cable.
When connecting to a network via Wired LAN, connect the projector to
the network hub with a commercially available LAN cable.
If you install the optional Wireless LAN unit in the projector, you can
connect to the network via a wireless LAN access point.
• You can easily connect to a computer and project images from the
computer without making network settings.
• This lets you connect easily without a connector cable, and you can
even connect if the projector and the computer are at remote locations.
Steps for Connecting
Use the following steps to connect the computer to the projector and
project in EasyMP Network Projection.
You need to perform steps 1 to 4 only the first time you connect.
Quick Connection Mode (Only when the optional
Wireless LAN unit is installed)
Quick Connection Mode is only available when you install the optional
Wireless LAN unit in the projector.
Quick Connection Mode temporarily assigns the projector's SSID to a
computer creating an ad hocg connection, and restores the computer's
network settings after disconnecting. s p.11
1.
Install EasyMP Network Projection on the computer to be connected.
s p.6
2.*
Make network settings on the computer and put it into network
connection status. s p.11
3.
For Quick Connection Mode: Install the optional Wireless LAN unit in
the projector (if already installed, go to step 5).
For Advanced Connection Mode: Enable the Wired LAN or Wireless
LAN adapter in "Port Configurations". s Computer's documentation
Two Connection Modes
4.
Make network settings on the projector and put it into network
connection status. s User's Guide "Network Menu"
5.
Start EasyMP Network Projection on the computer and connect with the
projector. s p.12
*
When the computer you are using is normally connected to the network, you
do not need to make network settings on the computer.
10
Preparing to Connect
Use the following procedure to set up the computer for connection.
For Windows
Make network settings for the computer by using the utility software
supplied with the LAN adapter. For more information on the utility
software, see the User's Guide supplied with your LAN adapter.
For example, as shown in the following illustration, when a red cross (^) is
displayed over the network icon on the taskbar, you cannot connect to the
projector.
For Mac OS
Set the network port and communication status. For more details on setting
the communication status, see the User’s Guides for your computer or the
AirPort card.
11
Connecting to a Projector on a Network and Projecting
Operating the Projector
Before connecting, put the projector into connection standby status.
Make sure the projector network settings are complete, and the projector is
connected to network equipment such as a network hub via a commercially
available network cable.
Procedure
A Press the [t] button on the remote control to turn the power
on.
B Press the [LAN] button on the Remote Control.
12
Operating the Computer
In the following explanations, unless otherwise noted, Windows screen
shots are used. The similar screens are also displayed in Mac OS.
Procedure
A Start EasyMP Network Projection.
For Windows
Select Start - Programs (or All Programs) - EPSON Projector EasyMP Network Projection - EasyMP Network Projection
V2.XX.
The LAN standby screen is displayed.
If there is no signal for the current input source, it automatically
switches to the LAN source. If it does not automatically switch to the
LAN source, press the [LAN] button.
For Mac OS
Double-click the Applications folder of the hard drive volume in
which EasyMP Network Projection is installed, and then double-click
the EasyMP Network Projection icon.
B Select "Quick Connection Mode" (only available when the
optional Wireless LAN unit is installed) or "Advanced
Connection Mode", and then click "OK".
The projector search results are displayed. To always connect using
Advanced Connection Mode, select Set the selected Connection
Mode as the default mode for future connections.
C Select the projector you want to connect to, and then click
"Connect".
If the projector you want to connect to is not displayed in the search
results, click the Automatic search button. The search takes about 30
seconds.
For details on the connection screen, see "Using the Connection
Screen". s p.13
Connecting to a Projector on a Network and Projecting
D When Projector Keyword is set to "On" from the projector, the
Keyword entry screen is displayed. Enter the keyword
displayed on the LAN standby screen, and then click "OK".
When the connection is complete, the computer screen is projected.
The following EasyMP Network Projection toolbar is displayed on the
computer screen. You can use this toolbar to operate the projector
and make settings, and to disconnect the network connection. For
details on the toolbar, see "Using the Toolbar". s p.15
q
When connecting from another computer, such as when changing
presenters, start EasyMP Network Projection from the computer you
want to connect. The computer that is currently connected is
disconnected, and the projector is then connected with the computer
that is trying to connect now.
If a connection is made while Disable interrupt connection is set, the
connection is not switched to another computer.
13
Using the Connection Screen
Start EasyMP Network Projection to display the following screen. The
operation of each button or item is described in the following table.
When the system starts in Advanced Connection Mode.
Connecting to a Projector on a Network and Projecting
When the system starts in Quick Connection Mode.
14
Busy (Disable
interrupt con‐
nection)
Currently in
use by another
application
Searching
Not found.
A
B
Automatic search
In Advanced Connection Mode, you can search for available projectors
on the network system to which the computer is connected.
In Quick Connection Mode, you can search for the projector based on
the SSID.
Manual search
In Advanced Connection Mode, you can search for a projector based on
a specified IP address or projector name.
In Quick Connection Mode, you can search for the projector based on
the SSID selected from a list.
C Status
The following six icons indicate the status of the detected projectors.
Standby
Select for connecting.
Busy
Select for connecting. When you click
Connect, the computer currently
connected is disconnected and your
computer is connected.
Cannot be selected. Disable interrupt
connection is set on another computer
which is already connected.
The projector's Configuration Menu is
open. You can select it after closing the
Configuration menu and running the
search again.
Displayed while running Manual search or
Profile.
Displayed when a projector cannot be found
as a result of Manual search or Profile. In
Quick Connection Mode, you can only
select multiple projectors with the same
SSID.
D Projector name
The projector's name is displayed.
E Disable interrupt connection
Check the box to prevent an interrupt connection by other computers while
connected to the selected projector.
F Use multi-display
Check the box to use the Multi-screen display function. When this is selected,
Display layout and Display properties are displayed at the bottom of the screen.
s p.20
G Troubleshooting
If there is a problem and you cannot have a connection, press this button to open
the EasyMP Network Projection Troubleshooting screen.
H Connect
Connect to the projector you selected from the search results list. When a
connection is made with a projector, a toolbar is displayed.
I Set options
You can make general setting options such as the processing method when
starting up EasyMP Network Projection. For details, see Set options. s p.34
J Save in the profile
Saves the results of a network projector search as a Profile. s p.30
Connecting to a Projector on a Network and Projecting
K Clear list
Deletes all search results.
L IP address (Advanced Connection Mode only)
The projector's IP address is displayed.
M Display
Select the number displayed (when Use multi-display is selected). s p.26
Profile
N
You can search for a projector on the network using a Profile saved
using Save in the profile. s p.30
O SSID (Quick Connection Mode only)
The projector's SSID is displayed.
P Signal intensity
This is displayed when the connection is made in Quick Connection Mode. As the
Signal intensity increases, so does the number of lit indicators.
Q Update list (Quick Connection Mode only)
Updates Status and Signal intensity.
15
Using the Toolbar
The toolbar is displayed on the computer screen after EasyMP Network
Projection starts and a connection is made with the projector. You can use
this toolbar to operate and make settings for the projector.
Select target projector
Click to limit the projectors operated from the toolbar when projecting
from multiple projectors using the distribution function or Multiscreen display. The indication below the icon shows the projectors that
can be controlled.
ALL indicates that all of the connected projectors can be controlled.
For example, when "1, 3" is displayed, projectors No. 1 and No. 3 can be
controlled.
Click
to display the following screen.
A Select the projector to be controlled.
B Indicates the No. of an allocated projector. This No. indicates the
No. of the projector that you can control from the toolbar.
C Indicates the status of the projector.
Stop
Connecting to a Projector on a Network and Projecting
Stops projection while connected to the projector. A black screen is
projected while stopped. Audio does not stop. To stop the audio, or to
display a User's Logo while projection is stopped, use the A/V Mute
function.
Show
Releases Stop or Pause.
Pause
Pauses projected images while connecting to the projector. The audio is
not paused.
16
Switch video source
The Source alternates between S-Video and Video
each time you click. S-Video does not switch if the
cable is not connected.
Screen Preview
Displays the multi-screen preview screen.
Click
to display a preview with the settings you have made. Click
each display to enlarge each Screen Preview to full-screen.
Presentation Mode
Each time this is clicked, Presentation Mode switches between enabled/
disabled. s p.19
Projector control
While the projector is connected to the network, the projector's A/V
Mute, Switch PC source and Switch video source functions can be
controlled from both the Remote Control and the projector's Control
panel.
Click
to display the following toolbar.
Set options
Transmission performance during the transfer of computer images can
be adjusted. s p.34
Movie Sending Mode
Not enabled on this projector. The message "The connected projectors
do not support Movie Sending." is displayed.
Disconnect
Disconnects the connection to the projector.
A/V Mute
The same function as the [A/V Mute] button on the
Remote Control.
s User's Guide "Remote Control"
Switch PC source
The Source alternates between Computer1,
Computer2, USB Display, USB, and LAN each time
you click.
Signal intensity
This is displayed when the connection is made in Quick Connection
Mode. As the Signal intensity increases, so does the number of lit
indicators.
Switch toolbar display
Connecting to a Projector on a Network and Projecting
The toolbar display is switched as follows. The toolbar display remains
as is until switched again.
Full
Normal
Simple
17
Functions and Settings for EasyMP Network Projection
This chapter explains the functions that may be useful in a meeting or presentation, such as the Multi-Screen Display which allows you to send images to
multiple projectors from a single computer.
Projecting Only a PowerPoint Slide Show (Presentation Mode)
In Presentation Mode, the images are only displayed when performing a
PowerPoint Slide Show on a computer. When you stop Slide Show, the
projector displays a black screen. This is useful when you only want to
display the Slide Show.
In addition to PowerPoint, Keynote is compatible with Presentation Mode
for Mac OS.
Procedure
A If necessary, select another projector to be controlled.
s p.15
B Click the
button on the toolbar.
Presentation Mode begins.
C In Presentation Mode, click the
Presentation Mode.
button again to exit
19
Using Multi-Screen Display
20
Multi-screen display mode allows you to project different images from multiple projectors that are connected to a single computer.
With Windows, multiple virtual displayg drivers can be set in the computer, and each image can be projected by the projector. Furthermore, this function
cannot be used in Windows Vista and Windows 7 because it is not compatible.
For Mac OS, an external monitor needs to be connected to the computer to enable this function. While the following explanation refers to virtual display, for
Mac OS the operation relates to the screens displayed on the physically connected monitor.
Using Multi-Screen Display
21
Example of Adjusting the Virtual Display
Arrangement example 2
By arranging the virtual displayg allocation, you can project only the image
that you want to show or project different images from left to right in a
presentation.
Arrangement example 1
A
Actual monitor image
B Image of virtual display
PowerPoint file presenter tools
Slide Show using a PowerPoint file
Procedure Before Using the Multi-screen Display
Function
A
Actual monitor image
B Image of virtual display
PowerPoint file
Excel file
1. Setting the Virtual Display s p.22
In a Windows environment, enable the virtual displayg driver as necessary. Also,
for both Windows and Mac OS, set up the virtual display arrangement.
2. Allocating the image to be projected s p.26
Using Multi-Screen Display
Open the file to be projected, and then move the screen to the virtual display
according to the actual projection arrangement.
3. Projecting the allocated images s p.26
Allocate a virtual display number to a projector that is connected through the
network, and then start projection.
22
C Click "OK".
Setting the Virtual Display
This chapter explains the virtual display for arrangement example 1.
s p.21
Enable the virtual display driver (Windows only)
Enable the virtual displayg driver. Those users listed below do not have to
perform this operation. Go to procedure s "Adjusting the Virtual Display"
p.22.
• Those users who have enabled virtual displays installing EasyMP
Network Projection.
• For Mac OS users.
Procedure
A Start Windows on the computer, and then select "Start" -
"Programs" (or "All Programs") - "EPSON Projector" - "EasyMP
Network Projection" - "Add-Remove Virtual Display".
The Add-Remove Virtual Display screen is displayed.
B Select the virtual display you want to use.
Up to four monitors can be added. In this example, a single virtual
display is to be used. When setting multiple virtual displays, select as
many displays as is necessary.
Any one of the displays can be selected.
When you click OK, the drivers for the virtual display are enabled. At
this point, it is normal for the display to flicker. Wait for the AddRemove Virtual Display screen to close.
Adjusting the Virtual Display
After starting EasyMP Network Projection, the procedure for setting up the
virtual displays differs for Windows and Mac OS. The procedures are
explained separately below.
q
Check the following points before starting EasyMP Network Projection
when connecting via Wireless LAN. If the following points are not set
correctly, Multi-screen display cannot be used.
• The SSID for the computer and each projector must be the same.
• The wireless LAN system for the computer and each projector must
be the same.
You can modify the SSID and Wireless LAN system for the
projector from the Network menu in the projector's Configuration
menu. s User's Guide "Wireless LAN Menu"
Using Multi-Screen Display
23
Procedure
For Windows
A Select "Start" - "Programs" (or "All Programs") - "EPSON
Projector" - "EasyMP Network Projection" - "EasyMP Network
Projection V2.XX" to start EasyMP Network Projection.
B Select the "Use multi-display" checkbox.
The Display Properties screen is displayed.
D Click the "Settings" tab.
Display layout and Display properties are added at the bottom of the
screen.
C Click "Display properties".
Using Multi-Screen Display
E Drag the displayed monitor icon and place it where desired.
Here, the actual monitor (1) is placed on the left, while the virtual
monitor (3) is placed on the right.
When the computer has multiple display output terminals, the
numbers assigned to the virtual terminals will be sequential to those
of the physical terminals.
24
q
• When an external monitor is connected as a secondary monitor, the
image for that screen cannot be projected.
• Depending on the hardware, the number of the secondary monitor
may be other than "2". When the monitor icon is displayed on the
screen, click the icon and confirm that the monitor type shown
under "Display" is other than "secondary".
• For the Screen Resolution settings, see the following. s p.37
When the monitor icon is arranged, a virtual display is connected as
the image like below.
Using Multi-Screen Display
25
C Click "Display preferences".
F Click the "OK" button to close the Display Properties screen.
Up to this point, the virtual display layout has been fixed.
Allocate the projecting images next. s p.26
For Mac OS
A Start EasyMP Network Projection. Double-click the Applications
folder of the hard drive volume in which EasyMP Network
Projection is installed, and then double-click the EasyMP
Network Projection icon.
In this example, we select and start in Advanced Connection
Mode.
The display setting screen is displayed.
D Click "Arrangement".
B Select the "Use multi-display" checkbox.
Display layout and Display preferences are added at the bottom of the
screen.
E Clear the "Mirror Displays" check box.
Using Multi-Screen Display
26
Allocating the Image to be Projected
This section explains the virtual display for arrangement example 1.
s p.21
Procedure
A Open the file to be projected.
Start the PowerPoint and Excel files.
B Drag the window to the desired virtual displayg monitor, and
F Drag the displayed monitor icon and place it where desired.
allocate it where the image is to be projected.
Drag the Excel window to the right until it cannot be seen. As a
result, the PowerPoint window appears on the actual monitor, while
the Excel window appears on the virtual display on the right.
Projecting the Allocated Images
This section explains the virtual display for arrangement example 1.
s p.21
G Close the display setting screen.
Up to this point, the screen layout has been fixed.
Procedure
A Select the number of the virtual displayg to allocate on the
"Display", and set which image to be projected from which
projector.
Using Multi-Screen Display
27
B Click "Connect".
The image allocated to each projector is projected.
In a Windows environment, you cannot view the image being sent to
a virtual display on the computer. To adjust the image on the virtual
display, you must do so while viewing the projected image.
To perform mouse-based operations on the virtual display, move the
mouse pointer in the direction of the virtual display, such that the
pointer appears on the virtual display.
C To terminate multi-screen display, click "Disconnect" on the
toolbar.
Using Multi-Screen Display
q
In a Windows environment, if the virtual display driver has been
enabled such that the mouse pointer can be moved outside the limits
of the screen, there may be occasions when you lose track of the
location of the pointer. If you are not using a virtual display, clear the
virtual display checkbox on the Add-Remove Virtual Display screen so
that the mouse pointer moves back inside the screen's display area. To
subsequently use multi-display again, place a check mark against the
required display under Add-Remove Virtual Display.
To clear a check mark, see the following. s p.22
28
Connecting to a Projector on a Different Subnet
This chapter explains how to connect a computer to a projector on a
different sub-net via a Wired LAN or a wireless LAN access point on an
existing network system.
By default, this application only searches for projectors on the same subnet
as the computer. Therefore, even if you perform a search for projectors on
the network, projectors on a different subnet will not be found.
You can, however, identify and connect to a projector on a different subnet
as follows:
• Specify either an IP address or Projector name and perform a search.
The IP Address can be input directly. Also, provided the Projector name
to be connected has been registered on the DNS server, you can perform
a search simply by inputting that Projector name. s p.29
• Performing a search based on a Profile
Once you have performed a search for a projector on a different subnet
by specifying either an IP Address or a Projector name, you can save the
search as a Profile with an easy-to-remember name, and then use that
Profile whenever you subsequently want to search for a projector on a
different subnet. s p.30
q
• If a search fails to find a projector, the most likely causes are as
follows. Proceed as appropriate, depending on the cause of the
failure.
For both Windows and Mac OS:
If there is no wireless LAN signal or if the signal is weak, check
whether there is anything that could be interfering with the signal.
When the optional Wireless LAN unit is installed in the projector,
and connecting Mac OS to a wireless LAN:
Check whether AirPort is set to On. Or, check whether an
appropriate access point has been selected.
• When you use Manual search in Quick Connection Mode, you can
specify the SSID. When there are a lot of projectors you can narrow
the search field by using SSID.
29
Specifying Either an IP Address or Projector Name
and Performing a Search (Advanced Connection
Mode Only)
In the following explanations, unless otherwise noted, Windows screen
shots are used.
The similar screens are also displayed for Mac OS.
Procedure
A Click "Manual search" on the EasyMP Network Projection
projector selection screen.
B Enter the IP address or the projector name for the projector
you want to connect to, and click "OK".
Connecting to a Projector on a Different Subnet
The search results are displayed on the EasyMP Network Projection
projector selection screen.
Provided the target projector has been identified, select that projector,
and then click Connect to establish a connection.
When you will always be using that projector, save the search as a
Profile, so that you do not have to specify the relevant details every
time you perform a search. s p.30
Performing a Search with a Profile
You can save a search for a frequently used projector as a Profile. A
"profile" is a file containing all of the information pertaining to a given
projector, such as the projector name, its IP address, and SSID. If you
specify that information from the next time you perform a search, there will
be no need to specify the IP address or projector name each time you
perform a search. For example, by creating a group of Profiles for each
place where a projector is setup and managing them with folders, the target
projector can be found quickly.
30
A
B
C
D
Building A
Building B
Building C
E
F
G
Floor 1
Floor 2
Floor 3
Building D
This section explains how to create and edit a Profile.
Making a Profile
Profiles are made by saving search results.
For details on how to edit a previously saved Profile, see the following
section. s p.32
Procedure
A While the projector is displayed on the EasyMP Network
Projection projector selection screen, click "Save in the
profile".
Connecting to a Projector on a Different Subnet
The Save in the profile screen is displayed.
31
For Mac OS
B Enter a Profile name, and then click "Add".
Projector information is registered in the Profile.
If you have previously saved a Profile, you are prompted to confirm
whether or not to overwrite. To save a Profile with a different name,
select Save as. If you have created a folder for a Profile, the following
screens are displayed. After entering the Profile name and selecting
the Save in destination, click Add.
For Windows
q
For details on how to create a folder for a Profile, see the following
section.s p.32
Searching by specifying a Profile
You can search by specifying the Profile you created.
Connecting to a Projector on a Different Subnet
Procedure
A Click "Profile" on the EasyMP Network Projection projector
selection screen.
If no Profile is registered, you cannot select Profile.
32
Managing a Profile
You can change the name and the hierarchical structure of the Profile.
Procedure
A Click "Set options" on the EasyMP Network Projection main
screen.
The Set options screen is displayed.
B Click "Edit profile".
B From the menu that is displayed, select the projector you want
to connect to.
The search results are displayed on the EasyMP Network Projection
projector selection screen.
Provided the target projector has been identified, select that projector,
and then click Connect to establish a connection.
The Edit profile screen is displayed.
C Edit the contents registered in the Profile.
Connecting to a Projector on a Different Subnet
33
Profile
Item
Function
Rename
You can display the Rename dialog box and rename the
folder or the Profile. You can enter up to 32 characters in
the Rename dialog box.
Create folder
You can create a new folder.
Export
Exports a created Profile allowing you to import and use
that Profile.
Import
Used when you want to read and use an exported
Profile.
Information on selected profile
A
: Indicates a folder.
B
: Indicates a Profile.
Function
Projector name,
IP address
You can display the projector information registered in
the Profile.
Delete
You can delete the information for the selected
projector. When all projector information is deleted, the
profile is also deleted.
D Click "OK".
Saves your edits and closes the Edit profile screen.
Profile
Item
Item
Function
Profile
You can display the registered Profile. You can manage
it by creating a folder. You can change the order of the
Profile or the folder by dragging & dropping.
Copy
You can copy the Profile. The copied Profile is saved in
the same folder as the original with the same name.
Delete
You can delete the Profile and the folder.
Using Set options
You can make setting options such as the processing method when EasyMP
Network Projection starts.
Access Set options from the EasyMP Network Projection main screen.
34
General settings tab
Procedure
A Click "Set options" on the EasyMP Network Projection main
screen.
Use full-screen
video transfer
This setting is disabled because the projector does not
support the movie sending function.
Encrypt
communications
Select to encrypt and transmit data. Even if data is
intercepted, it cannot be decrypted.
When using Quick Connection Mode, make sure you
always select this checkbox.
Display Connection
Mode Selection
window on startup
Set whether or not the Quick Connection Mode/Advanced
Connection Mode screen is displayed when EasyMP
Network Projection starts.
Clear this checkbox once you have settled on a regular
startup method.
Search method on
startup
Select from the following projector search methods
executed when EasyMP Network Projection is started.
Automatic search on startup
Specify search method after startup
Search with the last network configuration
The Set options screen is displayed.
B Set each of the items.
Confirm the details of the set items in the next step. When you have
made all the necessary settings, click OK to close the Set options
screen.
Setting Each Item
Set each item from the General settings tab and the Adjust performance
tab.
Using Set options
35
Edit profile
The Edit profile dialog box is displayed. s p.32
Switch LAN
Windows only
The Switch Network Adapter dialog box is displayed. This
is used when it is necessary to switch the network adapter to
be used for a search when a computer has multiple
adapters.
By default, all of the network adapters are used to perform a
search. When a Wired LAN is always used as the
connection method, select a Wired LAN adapter.
Restore Defaults
You can reset all adjustment values for Set options to their
default settings. However, you can retain settings for Edit
profile and Switch LAN in General settings.
Adjust performance tab
Transfer layered
window
Windows only (excluding Windows Vista and
Windows 7)
Set whether or not to transfer a layered window.
The layered window is in use when contents such as
messages displayed on the computer are not projected
by the projector. Select this checkbox to project
contents such as messages that use the layered
window.
Clear this checkbox if you do not want the mouse
pointer to flicker on the screen.
Restore Defaults
You can reset all adjustment values for Set options to
their default settings. However, you can retain settings
for Edit profile and Switch LAN in General settings.
q
When you click
on the toolbar, only the Adjust performance tab
is displayed.
Audio Output tab
Because this projector does not support the audio sending function, settings
on the Audio Output tab are disabled.
Performance
adjustment slider
The performance can be set to Fast, Normal, and
Fine.
Set to Fast when movie projections are interrupted.
Appendix
Connection Limitations
37
When projecting computer images while running EasyMP Network
Projection, the following restrictions apply. Confirm these points.
Supported Resolutions
Number of Connections
The following computer screen resolutions can be projected. You cannot
connect to a computer with a resolution greater than UXGAg.
•
•
•
•
•
•
•
•
•
•
*
The operational guarantee for multi-screen display is 16-bit and 32-bit
color.
VGA g(640x480)
SVGA g(800x600)*
XGA g(1024x768)*
SXGA g(1280x960)
SXGA (1280x1024)*
SXGA+ (1400x1050)*
WXGA (1280x768)
WXGA (1280x800)
WXGA+ (1440x900)
UXGA (1600x1200)
Supported resolutions when multi-screen display function is on.
When using a computer screen with a unique aspect ratio, depending on
the resolution of the computer and the projector, the resolution is increased
or decreased so as not to impair the image quality.
You can connect up to four projectors to one computer and project
simultaneously.
You cannot connect multiple computers to one projector simultaneously.
Others
• If the transmission speed of the Wireless LAN is low, the network
might be cut off unexpectedly.
• Audio is not transmitted.
• When videos are played back, they do not play back as smoothly as
when displayed on the computer.
• Applications that use part of DirectX functions may not be displayed
correctly. (Windows only)
• Cannot project full screen MS-DOS prompts. (Windows only)
• There are times when the image on the computer screen and the image
projected by the projector may not match exactly.
Depending on the resolution, at times the vertical or horizontal margins
may be projected in black.
When Using Windows Vista or Windows 7
Note the following points when using EasyMP Network Projection on a
computer running Windows Vista or Windows 7.
Display Color
The number of colors for computer screens that can be projected.
Windows
Mac OS
16-bit color
About 32,000 colors (16-bit)
32-bit color
About 16.7 million colors (32-bit)
Limitations when projecting from Windows Photo Gallery
Note the following two limitations when launching Windows Photo Gallery
when EasyMP Network Projection is running.
Connection Limitations
• Slide Show is played back in simple mode when projecting from
Windows Photo Gallery.
Because the toolbar is not displayed, you cannot make changes while
playing a Theme (effects), regardless of the Windows Experience Index
rating.
Once simple mode has started, you cannot change modes while Windows
Photo Gallery is running even if you close EasyMP Network Projection.
Restart Windows Photo Gallery.
38
• A few minutes after you connect a computer to the projector over a
network with EasyMP Network Projection, the following message is
displayed.
It is recommended that you select Keep the current color scheme, and
don't show this message again. This selection is enabled until the
computer is restarted.
• You cannot play movies.
Limitations in Windows Aero
Note the following two limitations when the window design for your
computer is Windows Aero.
• The layered window is projected regardless of Transfer layered window
from Set options in EasyMP Network Projection.
For example, when Transfer layered window for EasyMP Network
Projection toolbar is disabled, it is not projected even if it is displayed on
the computer screen, however the toolbar is projected.
Limitations when projecting from Windows Media Center
You cannot project images in full screen display using Windows Media
Center. Switch to the window display mode to project the images.
Troubleshooting
If any of the following problems occur, refer to the pages given for each
problem.
Problems concerning network functions
"Cannot connect to the projector." s p.40
"When a connection is made using EasyMP Network Projection, the projected
image remains as it is, and a connection cannot be made from another
computer." s p.40
"The projector is not found when EasyMP Network Projection is
started." s p.40
"Cannot connect in Advanced Connection Mode or Wired LAN
connection" s p.41
"The Slide Show cannot be displayed on the desired display when the multi-screen
display function is being executed." s p.42
"Applications are no longer displayed from the computer screen when the multiscreen display function is executed." s p.42
"The mouse cursor is not displayed on the computer screen." s p.42
"When connecting with EasyMP Network Projection the image is not displayed or
the image is slow to appear." s p.42
"When a connection is made using EasyMP Network Projection, a PowerPoint
Slide Show cannot be started." s p.43
"When a connection has been made using EasyMP Network Projection, the screen
will not be refreshed when using an Office application." s p.43
"Error message when starting up EasyMP Network Projection" s p.43
"Network settings are not restored after cutting the connection to the computer
with EasyMP Network Projection." s p.45
39
Troubleshooting
40
Problems Concerning Network Functions
Cannot connect to the projector.
Check the message on the screen and then apply the following countermeasures.
Error Messages
The application version used is not supported. Install the latest
version of the application on your computer.
Remedy
Install the current version of EasyMP Network Projection from the EPSON Projector Software CD-ROM supplied
with the projector.
When a connection is made using EasyMP Network Projection, the projected image remains as it is, and a connection cannot be made
from another computer.
Check
Remedy
Did the presenter leave the conference room without cutting off the With EasyMP Network Projection, the connection with the computer that was previously connected can be cut off
network connection?
when another computer tries to connect with the projector, and it connects with the computer that is trying to
connect.
Therefore, when a Projector Keyword is not set for the projector, or if you know the Projector Keyword, you can cut
off the current connection and, if you perform a connection operation, you can connect to the projector.
When a Projector Keyword is set for the projector, if you do not know the Projector Keyword, restart the projector and
reconnect.
The projector is not found when EasyMP Network Projection is started.
Check
Is the Wireless LAN unit connected?
Remedy
Check that the optional Wireless LAN unit is securely connected.
For Wireless LAN
Is the Network Configuration screen from the Configuration
menu displayed on the projector?
When the Network Configuration screen is displayed on the projector, network connection for EasyMP Network
Projection is disabled. Close network settings on the projector, and return to the LAN standby screen.
Are the computer's LAN card and the built-in LAN function
available?
Check that LAN is valid by checking Control Panel - System - Hardware in the device manager and so on.
Troubleshooting
41
Check
Is the SSID the same as that of the access point?
Remedy
Set an SSID that is different from that of the access point. s User's Guide "Network Menu"
Quick Connection Mode
Is the DHCP function for Wired LAN turned On?
Set the DHCP setting to Off from Wired LAN in the Configuration Menu. s User's Guide "Network Menu"
Quick Connection Mode
Was the network adapter used selected correctly with EasyMP
Network Projection?
If the computer has multiple LAN environments, it cannot connect unless the network adapter is selected correctly.
When using a computer running Windows, start EasyMP Network Projection and select the network adapter you are
using from Set options - Switch LAN. s p.34
For Wireless LAN connection, is the Wireless LAN setting enabled Enable the Wireless LAN.
when the computer is in power save mode?
Are there any obstacles between the access point and the computer Sometimes the electromagnetic wave situation prevents the projector from being found in a search. Check for any
or projector?
obstacles between the access point and the computer or projector, and change their position to improve the
electromagnetic wave situation.
For Wireless LAN
Is the computer's Wireless LAN electromagnetic wave set to low? Set the electromagnetic wave strength to maximum.
Does the Wireless LAN conform to 802.11g, 802.11b, or 802.11a? It is only compatible with standards 802.11g, 802.11b, and 802.11a, and not with other standards such as 802.11.
Is the firewall turned off, or has the firewall been registered as an
exception?
When you do not wish to turn off the firewall or register the firewall as an exception, make the necessary settings to
open the ports.
The ports used by EasyMP Network Projection are "3620", "3621", and "3629".
Is the network cable connected correctly?
Check that the network cable is connected correctly. Reconnect it if it is not connected or not connected properly.
For Wired LAN
Cannot connect in Advanced Connection Mode or Wired LAN connection
Check
Remedy
Is the SSID setting different.
Set the computer, the access point, and the projector to the same SSID.
s User's Guide "Network Menu"
Is the same WEP key set?
When selecting WEP from Security, set the access point, the computer, and the projector to the same WEP key.
s User's Guide "Network Menu"
Are the connection denial functions, such as MAC Addressg
Set the projector to allow connections from the access point.
restrictions and port restrictions, set correctly at the access point?
Troubleshooting
42
Check
Remedy
Are the IP address, the Subnet Mask, and the Gateway Address for When not using a DHCP, adjust each setting. s User's Guide "Network Menu"
the access point and the projector set correctly?
Are the access point and the projector's subnet different?
Select Manual search from EasyMP Network Projection, specify the IP address, and connect.
s p.29
The Slide Show cannot be displayed on the desired display when the multi-screen display function is being executed.
Check
Are you using PowerPoint 2002 or an earlier version?
For Windows
Remedy
To set and use two or more virtual displaysg, use PowerPoint 2003 or later, or limit the number of virtual displays to
one before displaying the Slide Show.
Applications are no longer displayed from the computer screen when the multi-screen display function is executed.
Check
Is another application running on the virtual displayg?
For Windows
Remedy
When Virtual Display is installed, another application sometimes runs on the virtual display. In this case, set Virtual
Display to "Off" in "Screen properties".
The mouse cursor is not displayed on the computer screen.
Check
Remedy
The mouse cursor was moved onto the virtual displayg. When the virtual display checkbox is cleared on the AddRemove Virtual Display screen, the mouse pointer returns to the screen display area.
Is Virtual Display installed?
For Windows
When connecting with EasyMP Network Projection the image is not displayed or the image is slow to appear.
Check
Remedy
Did you try to play back movies with Media Player or try to operate Depending on the computer, the movie playback screen in Media Player may not be displayed, and the screen saver
the screen saver preview?
preview may not be displayed normally.
Troubleshooting
43
Check
Remedy
Is WEP encryption effective, or are multiple projectors connected? The display speed decreases when WEP encryption is effective or multiple projectors are connected.
Have you enabled DHCP?
When DHCP is set to On in Advanced Connection Mode, if an available DHCP server is not found, it may take some
time to enter LAN standby status.
Is Wireless LAN 802.11g/b being used in Quick Connection
Mode?
Depending on the electromagnetic wave environment, there are times when the image and sound for movies may
stop. When using the movie sending function, use Advanced Connection Mode or Wireless LAN 802.11a in Quick
Connection Mode.
When a connection is made using EasyMP Network Projection, a PowerPoint Slide Show cannot be started.
Check
Remedy
Was EasyMP Network Projection started while PowerPoint was
running?
When connecting with EasyMP Network Projection, make sure you close PowerPoint first. Slide Show might not run
if connecting while PowerPoint is running.
For Windows
When a connection has been made using EasyMP Network Projection, the screen will not be refreshed when using an Office application.
Check
Is the mouse moved continuously?
Remedy
When you stop moving the mouse cursor, the screen is updated. If the screen does not update quickly, stop moving the
mouse cursor.
Error message when starting up EasyMP Network Projection
Error Messages
Connection to the projector failed.
Remedy
Try to connect again. If it still does not connect, check the network settings on the computer and the network settings
for the projector.
For details on the network settings to be made on the projector, see s User's Guide "Network Menu"
The keyword does not match. Re-enter the keyword displayed on Check the Projector Keyword displayed on the LAN standby screen, and enter the Projector Keyword.
the projector screen.
Troubleshooting
44
Error Messages
Remedy
The selected projector is busy. Do you want to continue the
connection process?
You tried to connect to a projector that is connected to another computer.
When the Yes button is clicked, it connects to the projector. The connection between the projector and the other
computer is cut off.
When No is clicked, it does not connect to the projector. The connection between the projector and the other
computer is maintained.
EasyMP Network Projection initialization failed.
Restart EasyMP Network Projection. If the message still appears, uninstall and then reinstall EasyMP Network
Projection.
s p.6
Connection failed due to keyword mismatch.
When connecting to a projector for which a Projector Keyword has been set, the wrong Projector Keyword is entered.
Check the Projector Keyword that is displayed on the projector's connection standby screen. After the connection is
disconnected and then reconnected, enter the Projector Keyword on the keyword entry screen that is displayed.
s p.12
Network adapter information could not be obtained.
Check the following point.
Is a network adapter installed on the computer?
Is the driver for the network adapter used installed on the computer?
After checking, restart the computer and connect again.
If you still cannot connect, check the following.
Check the network settings on the computer and the network settings on the projector.
For details on the network settings to be made on the projector, see s User's Guide "Network Menu"
One or more connected projectors do not support resolutions
greater than SXGA. Reduce the screen resolution and reconnect.
There is an ELP-735 projector in the connection destination. Change the computer screen resolution to SXGA
(1280x1024) or less.
One or more projectors are not responding.
You cannot connect to multiple projectors simultaneously. Check the network settings on the computer and the
network settings on the projector.
For details on the network settings to be made on the projector, see s User's Guide "Network Menu"
Enter the keyword displayed on the projector screen.
Check the Projector Keyword displayed on the LAN standby screen, and enter the Projector Keyword.
Cannot start this application while USB Display is running.
Close USB Display and then start EasyMP Network Projection.
Install the current version of EasyMP Network Projection from the EPSON Projector Software CD-ROM supplied
Cannot connect to the projector using this version of EasyMP
Network Connection. Install the latest version of EasyMP Network with the projector.
Projection.
Troubleshooting
45
Network settings are not restored after cutting the connection to the computer with EasyMP Network Projection.
Check
Are you manually connecting to a Wireless LAN when the
computer starts up?
Quick Connection Mode
Remedy
Try connecting to the Wireless LAN manually.
Glossary
46
This section briefly explains the difficult terms that are not explained in the text of this guide. For details, refer to other commercially available publications.
Ad hoc
A method of Wireless LAN connection that communicates with wireless LAN clients without using an access point. It is not possible to communicate
with two or more devices simultaneously.
MAC Address
An abbreviation of Media Access Control. The MAC Address is an ID number unique to each network adapter. A unique number is assigned to each
network adapter, and data is transmitted between network adapters based on this identification.
SVGA
A type of video signal with a resolution of 800 (horizontal) ^ 600 (vertical) dots that is used by IBM PC/AT-compatible computers.
SXGA
A type of video signal with a resolution of 1,280 (horizontal) ^ 1,024 (vertical) dots that is used by IBM PC/AT-compatible computers.
UXGA
A type of video signal with a resolution of 1,600 (horizontal) ^ 1,200 (vertical) dots that is used by IBM PC/AT-compatible computers.
VGA
A type of video signal with a resolution of 640 (horizontal) ^ 480 (vertical) dots that is used by IBM PC/AT-compatible computers.
Virtual Display
The screen for one computer is output to multiple displays. A large virtual screen can be created by using multiple displays.
XGA
A type of video signal with a resolution of 1,024 (horizontal) ^ 768 (vertical) dots that is used by IBM PC/AT-compatible computers.
General Notes
47
All rights reserved. No part of this publication may be reproduced, stored in a retrieval
system, or transmitted in any form or by any means, electronic, mechanical,
photocopying, recording, or otherwise, without the prior written permission of Seiko
Epson Corporation. No patent liability is assumed with respect to the use of the
information contained herein. Neither is any liability assumed for damages resulting
from the use of the information contained herein.
Neither Seiko Epson Corporation nor its affiliates shall be liable to the purchaser of this
product or third parties for damages, losses, costs, or expenses incurred by the
purchaser or third parties as a result of: accident, misuse, or abuse of this product or
unauthorized modifications, repairs, or alterations to this product, or (excluding the
U.S.) failure to strictly comply with Seiko Epson Corporation's operating and
maintenance instructions.
Seiko Epson Corporation shall not be liable against any damages or problems arising
from the use of any options or any consumable products other than those designated as
Original Epson Products or Epson Approved Products by Seiko Epson Corporation.
The contents of this guide may be changed or updated without further notice.
Illustrations in this guide and the actual projector may differ.
About Notations
Microsoft
Microsoft
Microsoft
Microsoft
Microsoft
®
®
®
®
®
®
®
®
®
®
Windows 2000 operating system
Windows XP Professional operating system
Windows XP Home Edition operating system
Windows Vista operating system
Windows 7 operating system
In this guide, the operating systems above are referred to as "Windows
2000," "Windows XP," "Windows Vista," and "Windows 7". Furthermore,
the collective term Windows may be used to refer to Windows 2000,
Windows XP, Windows Vista, and Windows 7, and multiple versions of
Windows may be referred to as, for example, Windows 2000/XP/Vista, with
the Windows notation omitted.
Mac
Mac
Mac
Mac
OS
OS
OS
OS
X
X
X
X
10.3.x
10.4.x
10.5.x
10.6.x
In this guide, the operating systems above are referred to as "Mac OS X
10.3.9," "Mac OS X 10.4.x," "Mac OS X 10.5.x," and "Mac OS X 10.6.x".
Furthermore, the collective term "Mac OS" is used to refer to them.
General Notice:
IBM, DOS/V, and XGA are trademarks or registered trademarks of International
Business Machines Corporation.
Macintosh, Mac, Mac OS, and iMac are trademarks of Apple Inc.
Microsoft, Windows, Windows NT, Windows Vista, PowerPoint, and Windows logo
are trademarks or registered trademarks of Microsoft Corporation in the United States
and/or other countries.
Other product names used herein are also for identification purposes only and may be
trademarks of their respective owners. Epson disclaims any and all rights in those
marks.
Software Copyright:
This product uses free software as well as software to which this company
holds the rights.
ZSEIKO EPSON CORPORATION 2010. All rights reserved.
Index
48
A
P
Adjust performance ..................................... 35
Advanced connection mode .................. 9, 12
Audio output ................................................ 35
Automatic search ......................................... 14
C
V
Presentation mode ......................................... 5
Problems ....................................................... 39
Profile ............................................................ 15
Projector control .......................................... 16
Q
Clear list ........................................................ 15
Copy .............................................................. 33
Create folder ................................................. 33
Quick connection mode ......................... 9, 12
R
Rename .......................................................... 33
D
Disable interrupt connection .....................
Display ...........................................................
Display preferences .....................................
Display properties ........................................
14
15
25
23
S
Save in the profile ........................................ 14
Screen preview ............................................. 16
Select target projector ................................. 15
Set options .............................................. 14, 34
Signal intensity ....................................... 15, 16
SSID ............................................................... 15
Status ............................................................. 14
Switch LAN .................................................. 35
E
Edit profile .............................................. 32, 35
G
General settings ............................................ 34
T
L
Toolbar .......................................................... 15
Transfer layered window ............................ 35
Troubleshooting .......................................... 14
Limitations .................................................... 37
M
Manual search ........................................ 14, 29
Mirror displays ............................................. 25
Movie sending mode ................................... 16
Multi-screen display .............................. 20, 21
U
Update list ..................................................... 15
Use full-screen video transfer .................... 34
Use multi-display ......................................... 14
Virtual display ........................................ 21, 22
Download PDF
Similar pages