FCC Notice
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide
reasonable protection against harmful interference in residential installation. This
equipment generates, uses and can radiate radio frequency energy and if not installed
and used in accordance with the instructions, may cause harmful interference to radio
communications. However, there is no guarantee that interference will not occur in a
particular installation. If this equipment does cause harmful interference to radio or
television reception, detectable by turning the equipment in question off and on, the
user is encouraged to try to correct the interference by one or more of the following
measures:
• Reorient or relocate the receiving antenna
• Increase the distance between the equipment and the receiver
• Connect the equipment to an outlet on a different circuit than that which the receiver
is connected to
• Or consult the dealer or an experienced radio/TV technician for help.
This device complies with Part 15 of the FCC Rules. Operation is subject to following
two conditions:
1. This device may not cause harmful interference, and
2. This device must accept any interference that may cause undesired operation.
i
Safety instructions
Read all of these instructions before you operate your projector and save for future
reference.
1. Read instructions
All the safety and operating instructions should be read before the appliance is
operated.
2. Notes and warnings
All notes and warnings in the operating instructions should be adhered to.
3. Cleaning
Unplug the projector from the wall socket before cleaning. Use a damp cloth for
cleaning the projector housing. Do not use liquid or aerosol cleaners.
4. Accessories
Do not place this product on an unstable cart, stand, or table. The product may fall,
causing serious damage to the product.
Keep the plastic packing materials (from the projector, accessories and optional
parts) out of the reach of children as these bags may result in death by suffocation.
Be particularly careful around the small children.
5. Ventilation
The projector is equipped with ventilation holes (intake) and ventilation holes
(exhaust).
Do not block or place anything near these slots, or internal heat build-up may
occur, causing picture degradation or damage to the projector.
6. Power sources
Check that the operating voltage of your unit is identical with the voltage of your
local power supply.
7. Servicing
Do not attempt to service this projector yourself. Refer all servicing to qualified
service personnel.
8. Replacement parts
When replacement parts are required, be sure that the replacement parts are
specified by the manufacture. Unauthorized substitutions may result in fire, electric
shock or other hazards.
9. Moisture Condensation
Never operate this projector immediately after moving it from a cold location to a
warm one. When the projector is exposed to such a change in temperature,
moisture may condense on the lens and the crucial internal parts. To prevent the
unit from possible damage, do not use the projector for at least 2 hours when there
is an extreme or sudden change in temperature.
ii
Notes on the AC Power Cord
AC Power Cord must meet the requirement of countries where you use this projector.
Please confirm your AC plug type with the graphics below and ensure that the proper
AC Power Cord is used. If the supplied AC Power Cord does not match your AC outlet, please contact your sales dealer. This projector is equipped with a grounding type
AC line plug. Please ensure that your outlet fits the plug. Do not defeat the safety purpose of this grounding type plug. We highly recommend using a video source device
also equipped with a grounding type AC line plug to prevent signal interference due to
voltage fluctuations.
Ground
Ground
For the U.S.A. and
Canada
For Australia and
Mainland China
Ground
Ground
For Continental Europe
For the U.K.
iii
Table of Contents
Introduction ........................................................................................... 1
Projector Features ................................................................................................................................. 1
Projector Overview ................................................................................................................................. 2
Using the Product ................................................................................. 4
Control Panel ......................................................................................................................................... 4
Connection Ports ................................................................................................................................... 5
Remote Control ...................................................................................................................................... 6
Installing the Batteries ............................................................................................................................ 9
Remote Control Operation ................................................................................................................... 10
Connection .......................................................................................... 11
Connecting a computer or monitor ....................................................................................................... 12
Connecting Video Source Devices ...................................................................................................... 13
Operation ............................................................................................. 14
Powering On/Off the Projector ............................................................................................................. 14
Adjusting the Projector Height ............................................................................................................. 15
Adjusting the Projector Focus and Zoom ............................................................................................. 15
Adjusting Projection Image Size .......................................................................................................... 16
Securing the projector .......................................................................................................................... 19
Setting the presentation timer .............................................................................................................. 20
Menu operation .................................................................................................................................... 21
Maintenance ........................................................................................ 30
Cleaning the Lens ................................................................................................................................ 30
Cleaning the Projector Housing ........................................................................................................... 30
Replacing the Lamp ............................................................................................................................. 31
Specifications ...................................................................................... 33
Dimensions .......................................................................................................................................... 34
Appendix .............................................................................................. 35
LED Indicator Messages ...................................................................................................................... 35
Compatibility Modes ............................................................................................................................. 36
Troubleshooting ................................................................................................................................... 39
RS-232 Protocol ................................................................................................................................... 40
iv
Introduction
Projector Features
The projector integrates high-performance optical engine projection and a user - friendly
design to deliver high reliability and ease of use.
The projector offers the following features:
•
•
•
•
•
DLP® technology
DS262: 800 x 600 SVGA resolution
DX263/DX281-ST: 1024 x 768 XGA resolution
DW265/DW282-ST: 1280 x 800 WXGA resolution
DH268: 1024 x 768 1080P resolution
Compatibility with Macintosh® computers
Compatibility with NTSC, PAL, SECAM and HDTV
D-Sub 15-pin terminal for analog video connectivity
User-friendly, multi-language on-screen display
Advanced electronic keystone correction
RS-232 connector for serial control
Less then 0.5w power consumption in standby mode.
Dynamic ECO starts your dynamic power saving
Quick Cooling, Auto Power Off, Auto Power On functions
Instant Restart function enables to restart the projector immediately within 90
seconds after turning it off.
• 3D Function supported
•
•
•
•
•
•
•
•
•
•
Note
• The information in this manual is subject to change without notices.
• The reproduction, transfer or copy of all or any part of this document is not permitted
without express written consent.
• The apparent brightness of the projected image will vary depending on the ambient
lighting conditions, selected input signal contrast/brightness settings, and the
projection distance.
• The lamp brightness will decline over time and may vary within the lamp manufacturers
specifications. This is normal and expected behavior.
1
Projector Overview
Front View
8
7
9
10
DS262/DX263/DW265/DH268
5
3
6
4
8
10
9
DX281-ST/DW282-ST
5
3
1.
3.
5.
7.
9.
6
4
Quick-release lever
Projection lens
Ventilation holes
Zoom ring
Control panel
2. Front adjuster foot
4. Front IR remote control sensor
6. Rear adjuster foot
8. Focus ring
10. Lamp cover
2
Rear View
2
3
1
1. AC power socket
3. Kensington anti-theft lock slot
2. Connection ports
Bottom View
216.0
84.0
44.0
107.5
2
1
Ceiling mount screws:
M4 x 8 (Max. L = 8 mm)
Unit: mm
1. Tripod socket
2. Ceiling mount holes
Note
• This projector can be used with a ceiling mount for support. The ceiling mount is not
included in the package.
• Contact your dealer for information to mount the projector on a ceiling.
• When installing the unit, incorporate a readily accessible disconnect device in the fixed
wiring, or connect the power plug to an easily accessible socket-outlet near the unit. If a
fault should occur during operation of the unit, operate the disconnect device to switch
the power supply off, or disconnect the power plug.
3
Using the Product
Control Panel
2
1
13
12
11
3
4
5
3
6
4
10
9
8
1.
POWER
Turns the projector on or off
2. SOURCE
Displays the source selection bar
3.
0 Volume
Adjusts volume
0 Keystone
4.
Corrects image-trapezoid (wider top/bottom) effect
5.
/ / / Up/Down/Left/Right keys
Navigates and changes settings in the OSD
6. ECO BLANK
Makes the screen blank
7. AUTO
Auto adjustment phase, h.size, position
8. MENU
Opens the OSD
9. BACK
Goes back to previous OSD menu
10. OK
Changes settings in the OSD
11. LAMP (Lamp LED indicator)
Refers to "LED Indicator Messages”
12. TEMP (Temp LED indicator)
Refers to "LED Indicator Messages”
13. POWER (Power LED indicator)
Refers to “LED Indicator Messages”
4
7
Connection Ports
1 2
3 4
9
8
5
6
7
1. USB MINI-B
This connector is for firmware update.
2. RS-232
When operating the projector via a computer, connect this to the controlling
computer's RS-232C port.
3. PC 1/PC 2
Connect image input signal (analog RGB or component) to this jack.
4. S-VIDEO
Connect S-Video output from video equipment to this jack.
5. HDMI-1/HDMI-2
Connect HDMI output from video equipment or computer to this jack.
6. AUDIO IN
Connect an audio output from video equipment or computer to this jack.
7. AUDIO OUT
Connect to a speaker or other audio input equipment.
8. VIDEO
Connect composite video output from video equipment to this jack.
9. MONITOR OUT
Connect to a computer display, etc.
5
Remote Control
1. IR transmitter
Transmits signal to projector
2. Status LED
Lights when the remote control is used
3. Power
Turns the projector on or off
4. VGA
Displays COMPUTER signal
5. Source
Displays the source selection bar
6.
Keystone
Corrects image-trapezoid (wider top/bottom) effect
Up/Down
Navigates and changes settings in the OSD
7.
Left/Right
Navigates and changes settings in the OSD
8. My Button
No function
9. Menu
Opens the OSD
10. Right mouse
No function
11. Left mouse
No function
6
12. Mouse
No function
13. Lock
No function
14. Pattern
No function
15. Blank
Makes the screen blank
16. Eco
Displays the lamp mode selection bar (Normal/Economic/Dynamic ECO).
17. Auto Sync
Auto adjustment phase, h.size, position
18. Video
Displays VIDEO signal
19. HDMI
Displays HDMI signal
20. Color Mode
Selects the display mode
21. Enter
Changes settings in the OSD
22. Exit
Exits and saves menu settings
23. Page Up
Page up when connected through USB to a PC
24. Page Down
Page down when connected through USB to a PC
25. Magnify
Magnifies the projected picture size
26. Volume
Adjusts volume
27. Freeze
Freeze/unfreeze the on-screen picture
28. Mute
Mutes the built-in speaker
29. Aspect
Selects the display aspect ratio
30. Timer
Activates P-Timer OSD menu
7
Using the remote mouse control
The capability of operating your computer with the remote control gives you more
flexibility when delivering presentations.
1. Connect the projector to your PC or notebook with a USB cable prior to using the
remote control in place of your computer’s mouse. See "Connecting a computer or
monitor" on page 12 for details.
2. Set the input signal to COMPUTER.
3. To operate your display software program (on a connected PC) which responds to
page up/down commands (like Microsoft PowerPoint), press Page Up/Page
Down.
4. If remote paging function doesn't work, check if the USB connection is correctly
made and the mouse driver on your computer is updated to the latest version.
8
Installing the Batteries
1. Open the battery cover in the
direction shown.
2. Install batteries as indicated by the
diagram inside the compartment.
3. Close the battery cover into position.
Caution
• Risk of explosion if battery is replaced by an incorrect type.
• Dispose of used batteries according to the instructions.
• Make sure the plus and minus terminals are correctly aligned when loading a battery.
Note
• Keep the batteries out of the reach of children. There is a danger of death by
accidentally swallowing the batteries.
• Remove batteries from remote control when not using for extended periods.
• Do not dispose of the used batteries along with household waste. Dispose of used
batteries according to local regulations.
• Danger of explosion may happen if batteries are incorrectly replaced. Replce all the
batteries with new ones.
• Batteries should not be in or near to fire or water, keep batteries in a dark, cool and dry
place.
• If suspect battery leakage, wipe out the leakage and then replace new batteries.
• If the leakage adheres to your body or clothes, rinse well with water immediately.
9
Remote Control Operation
Point the remote control at the infrared remote sensor and press a button.
• Operating the projector from the front
15
15
5m
8m
7m
Note
• Do not point the laser directly to the people's eyes (especially small children). There is a
danger of injury to the eyes.
• The remote control may not operate when there is sunlight or other strong light such as
a fluorescent lamp shining on the remote sensor.
• Operate the remote control from a position where the remote sensor is visible.
• Do not drop the remote control or jolt it.
• Keep the remote control out of locations with excessively high temperature or humidity.
• Do not get water on the remote control or place wet objects on it.
• Do not disassemble the remote control.
10
Connection
When connecting a signal source to the projector, be sure to:
1. Turn all equipment off before making any connections.
2. Use the correct signal cables for each source.
3. Ensure the cables are firmly inserted.
1
2
3
1
5
4
6
7
4
5
8
5
1. VGA cable (D-Sub to D-Sub)
3. USB cable (Mini B type to A type)
5. Audio cable
7. S-Video cable
2.
4.
6.
8.
VGA to DVI-A cable
HDMI cable
VGA (D-Sub) to HDTV (RCA) cable
Composite Video cable
Important
• In the connections shown above, some cables may not be included with the projector.
They are commercially available from electronics stores.
• The connection illustrations above are for reference only. The rear connecting jacks
available on the projector vary with each projector model.
11
Connecting a computer or monitor
Connecting a computer
The projector can connect to both IBM® compatibles and Macintosh® computers. A
Mac adapter is needed if you are connecting legacy version Macintosh computers.
To connect the projector to a notebook or desktop computer:
• Using a VGA cable
1. Take a VGA cable and connect one end to the D-Sub output socket of the
computer.
2. Connect the other end of the VGA cable to the PC 1/PC 2 signal input socket on
the projector.
• Using an HDMI cable
1. Take an HDMI cable and connect one end to the HDMI-1/HDMI-2 jack of the computer.
2. Connect the other end of the cable to the HDMI jack on the projector.
Important
• Many notebooks do not turn on their external video ports when connected to a
projector. Usually a key combo like FN + F3 or CRT/LCD key turns the external display
on/off. Locate a function key labeled CRT/LCD or a function key with a monitor symbol
on the notebook. Press FN and the labeled function key simultaneously. Refer to your
notebook's documentation to find your notebook's key combination.
Connecting a monitor
If you want to view your presentation close-up on a monitor as well as on the screen,
you can connect the MONITOR OUT signal output socket on the projector to an
external monitor with a VGA cable following the instructions below:
To connect the projector to a monitor:
1. Connect the projector to a computer as described in "Connecting a computer" on
page 12.
2. Take a suitable VGA cable (only one supplied) and connect one end of the cable
to the D-Sub input socket of the video monitor.
Or if your monitor is equipped with a DVI input socket, take a VGA to DVI-A cable
and connect the DVI end of the cable to the DVI input socket of the video monitor.
3. Connect the other end of the cable to the MONITOR OUT socket on the projector.
Important
• The output signal for MONITOR OUT jack only works when the input signal comes from
PC jack. When the projector is powered on, the output signal from MONITOR OUT jack
varies depending on the input signal from PC jack.
12
Connecting Video Source Devices
• Using an HDMI cable
1. Take an HDMI cable and connect one end to the HDMI-1/HDMI-2 jack of the computer.
2. Connect the other end of the cable to the HDMI jack on the projector.
• Using a VGA (D-Sub) to HDTV (RCA) cable
1. Take a VGA (D-Sub) to HDTV (RCA) cable and connect the end with 3 RCA type
connectors to the Component Video output sockets of the Video source device.
Match the color of the plugs to the color of the sockets; green to green, blue to
blue, and red to red.
2. Connect the other end of the cable (with a D-Sub type connector) to the PC 1/PC
2 socket on the projector.
• Connecting an S-Video/composite source device
1. Take an S-Video/Video cable and connect one end to the S-Video/Video output
jack of the Video source device.
2. Connect the other end of the S-Video/Video cable to the S-VIDEO/ VIDEO jack on
the projector.
Important
• If the selected video image is not displayed after the projector is turned on and the
correct video source has been selected, check that the Video source device is turned on
and operating correctly. Also check that the signal cables have been connected
correctly.
13
Operation
Powering On/Off the Projector
Powering On the Projector:
1. Complete the AC power cord and peripheral signal cable(s) connections.
2. Press
to turn on the projector.
The projector takes a minute or so to warm up.
3. Turn on your source (computer, notebook, DVD, etc.). The projector automatically
detects your source when Auto source setting is ON.
• If the projector doesn't detect a valid signal, the message 'No Signal' will continue to be displayed.
Warning
• Never look into the lens when the lamp is on. This can damage your eyes.
• This focal point concentrates high temperature. Do not place any object near it to avoid
possible fire hazard.
Powering Off the Projector:
1. Press
to turn off the projector lamp. You will see a message "Press
button
again to power off" appear on the screen.
2. Press
again to confirm.
• If you want to turn the projector back on, you must wait until the projector has
completed the cooling cycle and has entered stand-by mode. Once in stand-by
mode, simply press
to restart the projector.
3. Disconnect the AC power cord from the electrical outlet and the projector.
4. Do not turn on the projector right after power off.
14
Adjusting the Projector Height
•
Rear adjuster foot
Rear adjuster foot
Front adjuster foot
The projector is equipped with 1 front adjuster foot and 2 rear adjuster feet.
These adjusters change the image height and projection angle.
1. Pull the quick-release lever and lift the front of the projector. Once the image is
positioned where you want it, release the quick-release lever to lock the foot in
position. You may also screw the front adjuster foot to change the image height.
2. Use the rear adjuster foot to fine tune the horizontal angle.
To retract the foot, screw the adjuster foot in a reverse direction.
Note
• To avoid damaging the projector, make sure that the adjuster feet are fully retracted
before placing the projector in its carrying case.
Adjusting the Projector Focus and Zoom
Focus ring
Zoom ring
1. Focus the image by rotating the focus ring. A still image is recommended for focusing.
2. Adjust the image size by sliding the zoom ring.
15
Adjusting Projection Image Size
Refer to the graphic and table below to determine the screen size and projection
distance.
Diagonal
Diagonal
Screen
Center of lens
H
W Vertical offset
W
Projection distance
DS262/DX263
The screen aspect ratio is 4:3 and the projected picture is 4:3
Screen size
Diagonal
Inch
35
40
50
60
80
100
120
150
200
220
250
300
mm
889
1016
1270
1524
2032
2540
3048
3810
5080
5588
6350
7620
W
(mm)
H
(mm)
711
813
1016
1219
1626
2032
2438
3048
4064
4470
5080
6096
533
610
762
914
1219
1524
1829
2286
3048
3353
3810
4572
Projection distance (mm)
Min
Max
Vertical offset (mm)
Average
distance
distance
(max. zoom)
(min. zoom)
1380
1515
1650
32
1577
1731
1886
37
1971
2164
2357
46
2365
2597
2829
55
3154
3463
3771
73
3942
4328
4714
91
4730
5194
5657
110
5913
6492
7071
137
7884
8656
9428
183
8673
9522
10371
201
9855
10820
11786
229
11826
12984
14143
274
DW265
The screen aspect ratio is 16:10 and the projected picture is 16:10
Screen size
Diagonal
Inch
35
40
50
60
80
100
120
150
200
220
250
300
mm
889
1016
1270
1524
2032
2540
3048
3810
5080
5588
6350
7620
W
(mm)
H
(mm)
754
862
1077
1292
1723
2154
2585
3231
4308
4739
5385
6462
471
538
673
808
1077
1346
1615
2019
2692
2962
3365
4039
Projection distance (mm)
Min
Max
Vertical offset (mm)
Average
distance
distance
(max. zoom)
(min. zoom)
1168
1285
1402
19
1335
1469
1603
22
1669
1836
2003
27
2003
2203
2404
32
2671
2938
3205
43
3339
3672
4006
54
4006
4407
4808
65
5008
5509
6009
81
6677
7345
8013
108
7345
8079
8814
118
8346
9181
10016
135
10016
11017
12019
162
16
DH268
The screen aspect ratio is 16:9 and the projected picture is 16:9
Screen size
Diagonal
Inch
35
40
50
60
80
100
120
150
200
220
250
300
mm
889
1016
1270
1524
2032
2540
3048
3810
5080
5588
6350
7620
W
(mm)
H
(mm)
775
886
1107
1328
1771
2214
2657
3321
4428
4870
5535
6641
436
498
623
747
996
1245
1494
1868
2491
2740
3113
3736
Projection distance (mm)
Min
Max
Vertical offset (mm)
Average
distance
distance
(max. zoom)
(min. zoom)
1037
1149
1262
31
1192
1321
1450
35
1502
1664
1826
44
1813
2008
2202
52
2435
2695
2955
70
3057
3382
3708
87
3678
4069
4460
105
4610
5100
5589
131
6164
6817
7471
174
6785
7504
8223
192
7718
8535
9352
218
9271
10253
11234
262
Diagonal
Screen
Center of lens
H
W
Vertical offset
Projection distance
DX281-ST
The screen aspect ratio is 4:3 and the projected picture is 4:3
Screen size
Diagonal
W
Inch
mm
(mm)
35
889
711
40
1016
813
50
1270
1016
60
1524
1219
80
2032
1626
100
2540
2032
120
3048
2438
150
3810
3048
200
5080
4064
220
5588
4470
250
6350
5080
300
7620
6096
H
(mm)
533
610
762
914
1219
1524
1829
2286
3048
3353
3810
4572
Distance from screen (mm)
Vertical offset (mm)
448
512
640
768
1024
1280
1536
1920
2560
2816
3200
3840
32
37
46
55
73
91
110
137
183
201
229
274
17
DW282-ST
The screen aspect ratio is 16:10 and the projected picture is 16:10
Screen size
Diagonal
W
Inch
mm
(mm)
35
889
754
40
1016
862
50
1270
1077
60
1524
1292
80
2032
1723
100
2540
2154
120
3048
2585
150
3810
3231
200
5080
4308
220
5588
4739
250
6350
5385
300
7620
6462
H
(mm)
471
538
673
808
1077
1346
1615
2019
2692
2962
3365
4039
Distance from screen (mm)
Vertical offset (mm)
362
414
517
620
827
1034
1241
1551
2068
2275
2585
3102
18
20
25
30
41
51
61
76
102
112
127
152
Note
• Position the projector in a horizontal position; other positions can cause heat build-up
and damage to the projector.
• Keep a space of 30 cm or more between the sides of the projector.
•
Do not use the projector in a smoky environment. Smoke residue may buildup on
critical parts and damage the projector or its performance
• Consult with your dealer for special installation such as suspending from a ceiling.
18
Securing the projector
Setting and changing a password
1. Open the OSD menu, go to the SETTINGS 2 > Security Settings menu and
press Enter.
2. Highlight Change Password and press Enter.
3. To set the password:
According to the password you desire to set, press the arrow keys to enter six digits for the password.
4. To change the password:
You will be asked to input current password first and then you can change a new
one.
5. Confirm the new password by re-entering the password.
6. To leave the OSD menu, press Menu/Exit.
Activating the password function
1. Go back to SETTINGS 2 > Security Settings and press Enter.
2. Highlight Change Security and press Enter. You will be asked to input password.
Once the password is set, the OSD menu returns to the Power on Lock. Select
On by pressing / .
3. To disable password protection, select Off in the Power on Lock menu.
19
Setting the presentation timer
The presentation timer can indicate the presentation time on the screen to help you
achieve better time management when giving presentations. Follow these steps to
utilize this function:
1. Press Timer on the remote control to access the Presentation Timer menu or go to
the SETTINGS 1 > Presentation Timer menu and press Enter to display the
Presentation Timer page.
2. Highlight Timer Period and decide the timer period by pressing / .
3. Press to highlight Timer Display and choose if you want the timer to show up
on the screen by pressing / .
Selection
Always
1 Min/2 Min/3 Min
Never
Description
Displays the timer on screen throughout the presentation time.
Displays the timer on screen in the last 1/2/3 minute(s).
Hides the timer throughout the presentation time.
4. Press to highlight Timer Position and set the timer position by pressing / .
Top-Left → Bottom-Left → Top-Right → Bottom-Right
5. Press to highlight Timer Counting Direction and select your desired counting
direction by pressing / .
Selection
Count Up
Count Down
Description
Increases from 0 to the preset time.
Decrease from the preset time to 0.
6. Press to highlight Sound Reminder and decide if you want to activate sound
reminder by pressing / .
7. To activate the presentation timer, highlight Presentation Timer, select On and
select Yes.
8. To cancel the timer, highlight Presentation Timer, select Off and select Yes.
20
Menu operation
The projector has multilingual on-screen display (OSD) menus that allow you to make
image adjustments and change a variety of settings.
How to operate
1. Press Menu to open the OSD menu.
2. When OSD is displayed, use / to select any feature in the main menu.
3. After selecting the desired main menu item, press to enter sub-menu for feature
setting.
4. Use / to select the desired item and adjust the settings with / .
• To enter the next level of OSD menu, press Enter.
5. Press Menu twice* to leave and save the settings.
*The first press leads you back to the main menu and the second press closes the
OSD menu.
21
Menu tree
Note
• Supported on-screen display (OSD) menus vary by different input sources. The unsuported functions will be grayed out.
• *: Only available when Color Mode is selected to User1 or User2.
Main Menu
Sub Menu
Wall Color
DISPLAY
Aspect Ratio
Keystone
Position
Phase
H. Size
Digital Zoom
3D
Color Mode
PICTURE
SOURCE
Reference Mode*
Brightness
Contrast
Color
Tint
Sharpness
Brilliant Color
Color Temperature
Color Temperature
Fine Tuning
Settings
Off / Light Yellow / Pink / Light Green / Blue /
Blackboard
Auto / Real / 4:3 / 16:9 / 16:10
Auto / Top-Bottom / Frame
Sequential / Frame
3D Mode
Packing / Side By Side /
Off
3D Sync Invert
Disable / Invert
3D Settings 1 / 3D Settings
Save 3D Settings
2 /3D Settings 3
3D Settings 1 / 3D Settings
Apply 3D Settings
2 / 3D Settings 3 / Off
Bright / Presentation / sRGB / Movie / (3D) / User
1 / User 2
Bright / Presentation / sRGB / Movie / (3D)
On / Off
Cool / Normal / Warm
R Gain / G Gain / B Gain / R Offset / G Offset / B
Offset
Primary Color
R/G/B/C/M/Y
Hue
Color Management
Saturation
Gain
Reset Color
Current / All / Cancel
Settings
Auto Source
On / Off
22
Timer Period
Timer Display
Presentation Timer
Timer Position
1,2,3,4,5,10 - 240 Min
Always / 3 min / 2 min / 1
min / Never
Top-Left / Bottom-Left /
Top-Right / Bottom-Right
Timer Counting
Count Down / Count Up
Direction
Sound Reminder
On / Off
On / Off
Yes / No
Language
Multi-languages
Front Table / Rear Table / Rear Ceiling / Front
Projection
Ceiling
5 sec / 10 sec / 20 sec / 30
Menu Display Time
sec / Always
Center / Top-Left / TopMenu Settings
Menu Position
Right / Bottom-Right /
SETTINGS 1
Bottom-Left
Reminder Message On / Off
Direct Power On
On / Off
Signal Power On
On / Off
Disable / 3 min / 10 min /
Auto Power Off
15 min / 20 min / 25 min /
30 min
Quick Cooling
On / Off
Operation Settings
Instant Restart
On / Off
Disable / 5 min / 10 min /
Blank Timer
15 min / 20 min / 25 min /
30 min
Disable / 30 min / 1 hr / 2 hr
Sleep Timer
/ 3 hr / 4 hr / 8 hr / 12 hr
Background Color Factory Default / Black / Blue
Splash Screen
Factory Default / Black / Blue
23
High Altitude Mode On / Off
Mute
Audio Volume
Audio Settings
Power On/Off Ring
Tone
Lamp Mode
Lamp Settings
SETTINGS 2
Security Settings
Baud Rate
Test Pattern
Closed Caption
Standby Settings
Reset Settings
Native Resolution
INFORMATI
Current System
ON
Status
Reset lamp timer
Equivalent lamp hour
Change Password
Yes / No
On / Off
On / Off
Normal / Eco / Dynamic
ECO
Reset / Cancel
Power on
On / Off
Lock
2400 / 4800 / 9600 / 14400 / 19200 / 38400 /
57600 / 115200
On / Off
Closed Caption
On / Off
Enable
Caption Version
CC1 / CC2 / CC3 / CC4
Standby Monitor Out On / Off
Off/ Audio In / HDMI1 /
Audio Pass Through
HDMI2
Reset / Cancel
Change Security
Source
Color Mode
Resolution
Lamp Mode
3D Format
Color System
Equivalent lamp hour
Firmware Version
24
DISPLAY
Wall Color
Corrects the projected picture’s color when the projection surface is not white.
Aspect Ratio
There are four options to set the image's aspect ratio depending on your input signal
source.
Keystone
Corrects any keystoning of the image.
Position
Displays the position adjustment page. To move image, use the directional arrow
keys. The values lower position of the page change with every key until they reach
their maximum or minimum.
Phase
Adjusts the clock phase to reduce image distortion.
H. Size
Adjusts the horizontal width of the image.
Digital Zoom
Magnifies or reduces the projected image.
3D
This projector features a 3D function which enables you to enjoy the 3D movies,
videos, and sporting events in a more realistic way by presenting the depth of the
images. You need to wear a pair of 3D glasses to view the 3D images.
• 3D Mode: The default setting is Off. If the projector cannot recognize the 3D format,
choose a 3D Mode.
• 3D Sync Invert: When you discover the inversion of the image depth, enable this
function to correct the problem.
• Apply 3D Settings: The projector will apply saved 3D settings and keep these
settings when you reboot the projector next time.
• Save 3D Settings: The projector will memorize the current 3D settings.
25
PICTURE
Color Mode
Pre-defined display modes are provided so you can optimize your projector image setup to suit your program type.
Reference Mode
Selects a display mode that best suits your need for the image quality and further finetune the image based on the selections listed on the same page below.
Brightness
Adjusts the brightness of the image.
Contrast
Adjusts the degree of difference between dark and light in the image.
Color
Adjusts the color saturation level -- the amount of each color in a video image.
Tint
Adjusts the red and green color tones of the image.
Sharpness
Adjusts the image to make it look sharper or softer.
Brilliant Color
Selecting On enables a greater brightness increase in mid-tone images.
Color Temperature
The options available for color temperature settings vary according to the signal type
selected.
• Cool: Makes images appear bluish white.
• Normal: Maintains normal colorings for white.
• Warm: Makes images appear reddish white.
Color Temperature Fine Tuning
Sets a preferred color temperature.
• R Gain/G Gain/B Gain: Adjusts the contrast levels of Red, Green, and Blue.
• R Offset/G Offset/B Offset: Adjusts the brightness levels of Red, Green, and Blue.
Color Management
The Color Management provides six sets (RGBCMY) of colors to be adjusted. When
you select each color, you can independently adjust its range, hue, saturation and
gain according to your preference.
• Primary Color: selects a color from among Red, Yellow, Green, Cyan, Blue, or
Magenta.
• Hue: Increases in the range will include colors consisted of more proportions of its
two adjacent colors.
• Saturation: Is the amount of that color in a video picture. Lower settings produce
less saturated colors.
• Gain: The contrast level of the primary color you select will be affected.
26
Reset Color Settings
Resets current or all color modes.
• Current: returns current display mode to the factory preset settings.
• All: returns color mode settings to the factory preset settings.
SOURCE
Auto Source
If you want the projector to automatically search for the signals, be sure the Auto
Source function in the SOURCE menu is On (which is the default of this projector).
SETTINGS 1
Presentation Timer
Reminds the presenter to finish the presentation within a certain time frame.
Language
Sets the language for the On-Screen Display (OSD) menus.
Projection
The projector can be installed on a ceiling or behind a screen, or with one or more
mirrors.
Menu Settings
• Menu Display Time: Sets the length of time the OSD will remain active after your
last key press. The range is from 5 to 30 seconds in 5-second increments.
• Menu Position: Sets the On-Screen Display (OSD) menu position.
• Reminder Message: Sets whether to display the reminder message.
Operation Settings
• Direct Power On: Selecting On enables the function.
• Signal Power On: Selecting On the projector will turn on automatically when VGA
signal is detected. Selecting Off the projector has to be turnned on manually (by
keypad or remote).
• Auto Power Off: Allows the projector to turn off automatically if no input signal is
detected after a set period of time.
• Quick Cooling: Selecting On enables the function and the projector cooling time will
be shortened to a few seconds. If you attempt to restart the projector right after the
quick cooling process, it may not be turned on successfully and will rerun its cooling
fans.
• Instant Restart: When instant restart is on, users can restart projector immediately
within 90 secs after turning off projector.
• Blank Timer: Sets the image blank time when the Blank feature is activated, once
elapsed the image will return to the screen.
• Sleep Timer: Sets the auto-shutdown timer. The timer can be set to a value
between 30 minutes and 12 hours.
27
Background Color
Allows you to select which background color will display when no signal is input into
the projector.
Splash Screen
Allows you to select which logo screen will display during projector start-up.
SETTINGS 2
High Altitude Mode
Use this function to allow the fans operates at full speed continuously to achieve
proper high altitude cooling of the projector. If the projector is installed a filter cover,
make aure that High Altitude Mode is set to On.
Audio Settings
• Mute: Sets the mute function.
• Audio Volume: Adjusts the audio volume level.
• Power On/Off Ring Tone: Sets the power on/off ring tone.
Lamp Settings
• Lamp Mode: Using Eco/Dynamic ECO mode will reduces system noise and power
consumption. If the Eco/Dynamic ECO mode is selected, the light output will be
reduced and result in darker projected pictures, the projector protected for longer
working life.
• Reset lamp timer: Resets the light Hour to 0 hours.
• Equivalent lamp hour: Display the lamp’s elapsed operating time (in hours).
Security Settings
• Change Password: You will be asked to enter new password or the current
password before changing to a new one.
• Change Security: You can activate or disable the password protection once the
password is input.
Baud Rate
Selects a baud rate that is identical with your computer’s so that you can connect the
projector using a suitable RS-232 cable and update or download the projector’s
firmware. This function is intended for qualified service personnel.
Test Pattern
Selecting On enables the function and the projector displays the grid test pattern. It
helps you adjust the image size and focus and check that the projected image is free
from distortion.
Closed Caption
• Closed Caption Enable: Activates the function by selecting On when the selected
input signal carries closed captions.
• Caption Version: Selects a preferred closed captioning mode. To view captions,
select CC1, CC2, CC3, or CC4 (CC1 displays captions in the primary language in
your area).
28
Standby Settings
• Standby Monitor Out: Selecting On enables the function. The projector can output a
VGA signal when it is in standby mode and the PC and MONITOR OUT jacks are
correctly connected to devices.
• Audio Pass Through: The projector can play sound when it is in standby mode and
the corresponding jacks are correctly connected to devices.
Reset Settings
Returns all settings to the factory preset values.
Note
• The following settings will not be reset: User 1, User 2, Projector Installation, High
Altitude Mode, Security Settings and Baud Rate.
INFORMATION
Native Resolution
Shows the native resolution of the projector.
Current System Status
•
•
•
•
•
•
•
•
Source: Shows the current signal source.
Color Mode: Shows the selected mode in the PICTURE menu.
Resolution: Shows the native resolution of the input signal.
Lamp Mode: Shows the current lamp mode.
3D Format: Shows the current 3D mode.
Color System: Shows input system format RGB or YUV.
Equivalent lamp hour: Displays the number of hours the lamp has been used.
Firmware Version: Shows firmware version.
29
Maintenance
The projector needs proper maintenance. You should keep the lens clean as dust, dirt
or spots will project on the screen and diminish image quality. If any other parts need
replacing, contact your dealer or qualified service personnel. When cleaning any part
of the projector, always switch off and unplug the projector first.
Warning
• Never open any of the covers on the projector. Dangerous electrical voltages inside the
projector can cause severe injury. Do not attempt to service this product yourself. Refer
all servicing to qualified service personnel.
Cleaning the Lens
Gently wipe the lens with lens cleaning paper. Do not touch the lens with your hands.
Cleaning the Projector Housing
Gently wipe with a soft cloth. If dirt and stains are not easily removed, use a soft cloth
damped with water, or water and neutral detergent, and wipe dry with a soft, dry cloth.
Note
• Turn off the projector and remove the AC power cord from the power outlet before
beginning maintenance work.
• Make sure the lens is cool before cleaning.
• Do not use detergents or chemicals other than those noted above. Do not use benzene
or thinners.
• Do not use chemical sprays.
• Use a soft cloth or lens paper only.
30
Replacing the Lamp
As the projector operates over time, the brightness of the projector lamp gradually
decreases and the lamp becomes more susceptible to breakage. We recommend
replacing the lamp if a warning message is displayed. Do not attempt to replace the
lamp yourself. Contact the qualified service personnel for replacement.
Note
• The lamp is extremely hot right after turning off the projector. If you touch the lamp, you
may scald your finger. When you replace the lamp, wait for at least 45 minutes for the
lamp to cool down.
• Do not touch the lamp glass at any time. The lamp may explode due to improper
handling, including the touching of the lamp glass.
• Lamp lifetime may differ from lamp to lamp and according to the environment of use.
There is no guarantee of the same lifetime for each lamp. Some lamps may fail or
terminate their lifetime in a shorter period of time than other similar lamps.
• A lamp may explode as a result of vibration, shock or degradation as a result of hours of
use as its lifetime draws to an end. Risk of explosion may differ according to the
environment or conditions in which the projector and lamp are being used.
• Wear protective gloves and eyeglasses when fixing or detaching the lamp.
• Faster on-off-cycles will damage the lamp and reduce lamp life. Wait at least for 5
minutes to turn off the projector after powering on.
• Do not operate the lamp in proximity to paper, cloth, or other combustible material nor
cover it with such materials.
• Do not operate the lamp in an atmosphere containing an inflammable substance, such
as thinner.
• Thoroughly ventilate the area or the room when operating the lamp in an oxygen
atmosphere (in the air). If ozone is inhaled, it could cause headaches, nausea, dizziness,
and other symptoms.
• The inorganic mercury is involved in the lamp. If the lamp bursts, the mercury inside the
lamp will be exposed. Leave the area immediately if the lamp shatters while being
operated and ventilate the area for at least 30 minutes in order to avoid the inhalation of
mercury fumes. Otherwise it could be harmful to user’s health.
31
1. Turn off the projector.
2. If the projector is installed in a ceiling mount, remove it
3. Unplug the power cord.
4. Use a screwdriver to remove the screw from the cover. (Illustration #1)
Push up and remove the cover. (Illustration #2)
5. Remove the screw from the lamp module. (Illustration #3)
Raise the handle, and lift out the module. (Illustration #4)
2
1
3
4
6. Insert the new lamp module into the projector and tighten the screws.
7. Replace the lamp cover and tighten the screw.
8. Turn on the projector. If the lamp does not turn on after the warm-up period, try
reinstalling the lamp.
9. Reset the lamp hour. Refer to the “SETTINGS 2 > Lamp Settings > Reset lamp
timer” menu.
Note
• Dispose the used lamp according to local regulations.
• Ensure that screws are tightened properly. Screws not tightened fully may result in
injury or accidents.
• Since the lamp is made of glass, do not drop the unit and do not scratch the glass.
• Do not reuse the old lamp. This could cause the lamp to explode.
• Be sure to turn off the projector and unplug the AC power cord before replacing the
lamp.
• Do not use the projector with the lamp cover removed.
32
Specifications
Model name
Display devices
Resolution
Lens
Input
terminal
Output
terminals
F number
Zoom
Focus
HDMI
D-Sub 15-pin
S-Video
Video
Audio (PC
audio jack)
D-Sub 15-pin
Audio (PC
audio jack)
USB (mini- B)
RS-232
DS262
DX263
DW265
DH268
0.55” DLP Chip
0.65” DLP Chip
SVGA
XGA
WXGA
1080P
(800×600)
(1024×768)
(1280x800)
(1920x1080)
F 2.46-2.66
1.2x
f=21.8-25.6
f=19.0-22.65
x2
x2
x1
x1
DX281-ST
DW282-ST
0.55” DLP Chip 0.65” DLP Chip
XGA
WXGA
(1024×768)
(1280x800)
F 2.7
f=7.2
x1
x1
x1
x1
x1
2Wx1
203W
Control
terminals
Speaker
Projection lamp
Operation:
Temperature: 0°C to 40°C
Humidity: 10%-90% (without condensation)
Environmental Requirements
Storage:
Temperature: -20°C to 60°C
Humidity: 10%-90% (without condensation)
Power supply
AC 120-240 V, 50 - 60 Hz, 2.60 A
Power consumption
240 W at Normal Mode
Dimension
332 mm (W) x 243 mm (D) x 107 mm (H)
Weight
2.6 kg (5.7 lbs)
Note: Design and Specifications are subject to change without prior notice.
33
332 mm (W) x 243.6 mm (D) x
107 mm (H)
Dimensions
DS262/DX263/DW265/DH268
332 mm (W) x 243 mm (D) x 107 mm (H)
332.0
243.0
107.0
DX281-ST/DW282-ST
332 mm (W) x 243.6 mm (D) x 107 mm (H)
332.0
243.6
107.0
Ceiling mount installation
216.0
Ceiling mount screws:
M4 x 8 (Max. L = 8mm)
44.0
Unit: mm
84.0
107.5
34
Appendix
LED Indicator Messages
POWER
Light
TEMP
Status & Description
LAMP
System Message
Orange
Green
Flashing
Green
Orange
Flashing
Off
Off
Stand-by mode
Off
Off
Powering up
Off
Off
Normal operation
Off
Off
Normal power-down cooling
Green
Off
Red
Flashing
Red
Green
Green
Off
Green
Off
Green
Red Flashing Red Flashing
Download
CW start fail
Burn-In Messages
Off
Off
Off
Off
Red
Red
Red
Green
Green
Green
Green
Flashing
Orange
Flashing
Red
Red Flashing
Green
Green
Flashing
Burn-in ON
Burn-in OFF
Lamp Error Messages
Red
Lamp1 error in normal operation
Orange
Lamp is not lit up
Flashing
Thermal Error Messages
Fan 1 error (the actual fan speed is outside the desired
Off
speed)
Fan 2 error (the actual fan speed is outside the desired
Off
speed)
Off
Temperature 1 error (over limited temperature)
Off
Thermal Sensor 1 open error
Off
Thermal Sensor 1 short error
Off
Thermal IC #1 I2C Connection error
35
Compatibility Modes
1. VGA Analog
Supported timing for PC input
Resolution
640 x 480
720 x 400
800 x 600
1024 x 768
1152 x 864
1280 x 720
1280 x 768
1280 x 800
1280 x 1024
1280 x 960
1360 x 768
1440 x 900
1400 x 1050
1600 x 1200
1680 x 1050
640 x 480
@67Hz
832 x 624
@75Hz
1024 x 768
@75Hz
1152 x 870
@75Hz
Timing
VGA_60
VGA_72
VGA_75
VGA_85
720 x 400_70
SVGA_60
SVGA_72
SVGA_75
SVGA_85
SVGA_120
(Reduce
Blanking)
XGA_60
XGA_70
XGA_75
XGA_85
XGA_120
(Reduce
Blanking)
1152 x 864_75
1280 x 720_60
1280 x
720_120
1280 x 768_60
WXGA_60
WXGA_75
WXGA_85
WXGA_120
(Reduce
Blanking)
SXGA_60
SXGA_75
SXGA_85
1280 x 960_60
1280 x 960_85
1360 x 768_60
WXGA+_60
SXGA+_60
UXGA
1680 x
1050_60
◎
3D
top
botto
m
◎
3D
side
by
side
◎
◎
◎
◎
◎
◎
◎
◎
◎
◎
◎
◎
◎
◎
◎
◎
◎
◎
◎
◎
◎
◎
◎
◎
◎
◎
Horizontal
Frequency
(KHz)
Vertical
Frequency
(Hz)
Pixel
Frequency
(MHz)
59.94
72.809
75
85.008
70.087
60.317
72.188
75
85.061
31.469
37.861
37.5
43.269
31.469
37.879
48.077
46.875
53.674
25.175
31.500
31.500
36.000
28.3221
40.000
50.000
49.500
56.250
119.854
77.425
83.000
◎
60.004
70.069
75.029
84.997
48.363
56.476
60.023
68.667
65.000
75.000
78.750
94.500
◎
119.989
97.551
115.5
◎
75
60
67.5
45
108
74.250
◎
3D Field
Sequential
120
90.000
148.500
◎
59.87
59.81
74.934
84.88
47.776
49.702
62.795
71.554
79.5
83.500
106.500
122.500
◎
◎
119.909
101.563
146.25
◎
60.02
75.025
85.024
60
85.002
60.015
59.887
59.978
60
63.981
79.976
91.146
60
85.938
47.712
55.935
65.317
75
108.000
135.000
157.500
108.000
148.500
85.5
106.500
121.750
162.000
59.954
65.29
146.25
MAC13
66.667
35
30.240
MAC16
74.546
49.722
57.280
MAC19
75.02
60.241
80.000
MAC21
75.06
68.68
100.000
• The timings showing above may not be supported due to EDID file and VGA graphic card
limitations. It is possible that some timings cannot be chosen.
36
Supported timing for Component-YPbPr input
Timing
Resolution
480i
480p
576i
576p
720/50p
720/60p
1080/50i
1080/60i
1080/24P
1080/25P
1080/30P
1080/50P
1080/60P
720 x 480
720 x 480
720 x 576
720 x 576
1280 x 720
1280 x 720
1920 x 1080
1920 x 1080
1920 x 1080
1920 x 1080
1920 x 1080
1920 x 1080
1920 x 1080
Horizontal
Frequency
(KHz)
15.73
31.47
15.63
31.25
37.5
45.00
28.13
33.75
27
28.13
33.75
56.25
67.5
Vertical
Frequency
(Hz)
59.94
59.94
50
50
50
60
50
60
24
25
30
50
60
Pixel Frequency
(MHz)
3D Field
Sequential
13.5
27
13.5
27
74.25
74.25
74.25
74.25
74.25
74.25
74.25
148.5
148.5
◎
◎
◎
2. HDMI Digital
Supported timing for PC input
Resolution
640 x 480
720 x 400
800 x 600
1024 x 768
1152 x 864
1280 x 720
1280 x 768
1280 x 800
1280 x 1024
1280 x 960
1360 x 768
1440 x 900
1400 x 1050
1600 x 1200
1680 x 1050
Timing
VGA_60
VGA_72
VGA_75
VGA_85
720 x 400_70
SVGA_60
SVGA_72
SVGA_75
SVGA_85
SVGA_120
(Reduce
Blanking)
XGA_60
XGA_70
XGA_75
XGA_85
XGA_120
(Reduce
Blanking)
1152 x 864_75
1280 x
720_60
1280 x
768_60
WXGA_60
WXGA_75
WXGA_85
WXGA_120
(Reduce
Blanking)
SXGA_60
SXGA_75
SXGA_85
1280 x
960_60
1280 x
960_85
1360 x
768_60
WXGA+_60
SXGA+_60
UXGA
1680 x
1050_60
◎
3D
top
botto
m
◎
3D
side
by
side
◎
◎
◎
◎
◎
◎
◎
◎
◎
Horizontal
Frequency
(KHz)
Vertical
Frequency
(Hz)
Pixel
Frequency
(MHz)
59.94
72.809
75
85.008
70.087
60.317
72.188
75
85.061
31.469
37.861
37.5
43.269
31.469
37.879
48.077
46.875
53.674
25.175
31.500
31.500
36.000
28.3221
40.000
50.000
49.500
56.250
119.854
77.425
83.000
◎
60.004
70.069
75.029
84.997
48.363
56.476
60.023
68.667
65.000
75.000
78.750
94.500
◎
119.989
97.551
115.5
◎
75
67.5
108
60
45
74.250
3D Field
Sequential
59.87
47.776
79.5
◎
◎
◎
59.81
74.934
84.88
49.702
62.795
71.554
83.500
106.500
122.500
◎
◎
◎
119.909
101.563
146.25
◎
60.02
75.025
85.024
63.981
79.976
91.146
108.000
135.000
157.500
◎
◎
60
60
108.000
◎
◎
85.002
85.938
148.500
60.015
47.712
85.5
◎
◎
59.887
59.978
60
55.935
65.317
75
106.500
121.750
162.000
◎
◎
◎
◎
◎
◎
59.954
65.29
146.25
◎
◎
37
640 x 480
@67Hz
832 x 624
@75Hz
1024 x 768
@75Hz
1152 x 870
@75Hz
1920 x 1080
1920 x 1200
MAC13
66.667
35
30.240
MAC16
74.546
49.722
57.280
MAC19
75.02
60.241
80.000
MAC21
75.06
68.68
100.000
67.5
60
148.5
◎
◎
59.95
74.038
154.000
◎
◎
1920 x
1080_60
1920 x
1200_60
(Reduce
Blanking)
• The timings showing above may not be supported due to EDID file and VGA graphic card
limitations. It is possible that some timings cannot be chosen.
Supported timing for video input
576p
720/50p
720/60p
1080/50i
1080/60i
1080/24P
1080/25P
1080/30P
1080/50P
1080/60P
Pixel
Frequency
(MHz)
15.73
59.94
27
◎
◎
31.47
59.94
27
15.63
50
27
31.25
37.5
45.00
28.13
33.75
27
28.13
33.75
56.25
67.5
50
50
60
50
60
24
25
30
50
60
27
74.25
74.25
74.25
74.25
74.25
74.25
74.25
148.5
148.5
◎
3D Side by Side
576i
Vertical
Frequency
(Hz)
3D Top-Bottom
480p
720 (1440) x
480
720 x 480
720 (1440) x
576
720 x 576
1280 x 720
1280 x 720
1920 x 1080
1920 x 1080
1920 x 1080
1920 x 1080
1920 x 1080
1920 x 1080
1920 x 1080
Horizontal
Frequency
(KHz)
3D Frame Packing
480i
Resolution
3D Field Sequential
Timing
◎
◎
◎
◎
◎
◎
◎
◎
◎
◎
◎
◎
◎
◎
◎
3. Video/S-Video
Supported timing for Video input
Video mode
NTSC
PAL
SECAM
PAL-M
PAL-N
PAL-60
NTSC4.43
Horizontal Frequency
(kHz)
15.73
15.63
15.63
15.73
15.63
15.73
15.73
Vertical Frequency
(Hz)
60
50
50
60
50
60
60
38
Color sub-carrier
Frequency (MHz)
3.58
4.43
4.25 or 4.41
3.58
3.58
4.43
4.43
3D Field Sequential
◎
Troubleshooting
Refer to the symptoms and measures listed below before sending the projector for
repairs. If the problem persists, contact your local reseller or service center. Please
refer to "LED Indicator Messages" as well.
Start-up problems
If no lights turn on:
• Be sure that the power cord is securely connected to the projector and the other end is
plugged into an outlet with power.
• Press the power button again.
• Unplug the power cord and wait for a short while, then plug it in and press the power
button again.
Image problems
If the searching source is displayed:
• Press Source on the remote control to select an active input source.
• Be sure the external source is turned on and connected.
• For a computer connection, ensure your notebook computer’s external video port is
turned on. Refer to the computer manual.
If the image is out of focus:
• While displaying the on-screen menu, adjust the focus ring. (The image size should
not change; if it does, you are adjusting the zoom, not the focus.)
• Check the projection lens to see if it needs cleaning.
If the image is flickering or unstable for a computer connection:
• Press Auto Sync on the remote control.
Remote control problems
If the remote control does not operate:
• Be sure nothing is blocking the remote control receiver on the front of the projector.
Use the remote control within the effective range.
• Aim the remote control at the screen or at the front or back of the projector.
• Move the remote control so it is more directly in front of or behind the projector and
not as far to the side.
39
RS-232 Protocol
RS-232 Setting
Baud rate:
Parity check:
Data bit:
Stop bit:
Flow control:
Function
Power
9600
None
8
1
None
Type
Operation
ASCII
Write
Power On
<CR>$pow=on#<CR>
Write
Power off
<CR>$pow=off#<CR>
Read
Power Status
<CR>$pow=?#<CR>
Write
Write
Source
Selection
COMPUTER/
YPbPr
COMPUTER 2/
YPbPr2
<CR>$sour=RGB#<CR>
<CR>$sour=RGB2#<CR>
Write
HDMI
<CR>$sour=hdmi#<CR>
Write
HDMI2
<CR>$sour=hdmi2#<CR>
Write
Composite
<CR>$sour=vid#<CR>
Write
S-Video
<CR>$sour=svid#<CR>
Read
Current source
<CR>$sour=?#<CR>
Write
Mute On
<CR>$mute=on#<CR>
Write
Mute Off
<CR>$mute=off#<CR>
Read
Mute Status
<CR>$mute=?#<CR>
Write
Volume +
<CR>$vol=+#<CR>
Write
Volume -
<CR>$vol=-#<CR>
Read
Volume Status
<CR>$vol=?#<CR>
Audio Control
40
HEX
0D 24 50 4F 57 3D 4F 4E
23 0D
0D 24 50 4F 57 3D 4F 46
46 23 0D
0D 24 50 4F 57 3D 3F 23
0D
0D 24 53 4F 55 52 3D 52
47 42 23 0D
0D 24 53 4F 55 52 3D 52
47 42 32 23 0D
0D 24 53 4F 55 52 3D 48
44 4D 49 23 0D
0D 24 53 4F 55 52 3D 48
44 4D 49 32 23 0D
0D 24 53 4F 55 52 3D 56
49 44 23 0D
0D 24 53 4F 55 52 3D 53
56 49 44 23 0D
0D 24 53 4F 55 52 3D 3F
23 0D
0D 24 4D 55 54 45 3D 4F
4E 23 0D
0D 24 4D 55 54 45 3D 4F
46 46 23 0D
0D 24 4D 55 54 45 3D 3E
3F 23 0D
0D 24 56 4F 4C 3D 2B 23
0D
0D 24 56 4F 4C 3D 2D 23
0D
0D 24 56 4F 4C 3D 3F 23
0D
Color Mode
Write
Bright
Write
Presentation
Write
sRGB
Write
Movie
Write
Standard
Write
User1
Write
User2
Read
Color Mode
0D 24 41 50 50 4D 4F 44
<CR>$appmod=dynamic#<
3D 44 59 4E 41 4D 49 43
CR>
23 0D
0D 24 41 50 50 4D 4F 44
<CR>$appmod=preset#<C
3D 50 52 45 53 45 54 23
R>
0D
<CR>$appmod=srgb#<CR 0D 24 41 50 50 4D 4F 44
>
3D 53 52 47 42 23 0D
<CR>$appmod=cine#<CR 0D 24 41 50 50 4D 4F 44
>
3D 43 49 4E 45 23 0D
0D 24 41 50 50 4D 4F 44
<CR>$appmod=std#<CR>
3D 53 54 44 23 0D
<CR>$appmod=user1#<C 0D 24 41 50 50 4D 4F 44
R>
3D 55 53 45 52 31 23 0D
<CR>$appmod=user2#<C 0D 24 41 50 50 4D 4F 44
R>
3D 55 53 45 52 32 23 0D
0D 24 41 50 50 4D 4F 44
<CR>$appmod=?#<CR>
3D 3F 23 0D
41
Write
Write
Read
Write
Write
Read
Write
Write
Read
Picture Setting
Write
Write
Read
Write
Write
Write
Write
Write
Write
Write
Write
Write
Write
Write
Baud Rate
Write
Write
Write
0D 24 43 4F 4E 3D 2B 23
0D
0D 24 43 4F 4E 3D 2D 23
Contrast <CR>$con=-#<CR>
0D
0D 24 43 4F 4E 3D 3F 23
Contrast value
<CR>$con=?#<CR>
0D
0D 24 42 52 49 3D 2B 23
Brightness +
<CR>$bri=+#<CR>
0D
0D 24 42 52 49 3D 2D 23
Brightness <CR>$bri=-#<CR>
0D
0D 24 42 52 49 3D 3F 23
Brightness value <CR>$bri=?#<CR>
0D
0D 24 43 4F 4C 4F 52 3D
Color +
<CR>$color=+#<CR>
2B 23 0D
0D 24 43 4F 4C 4F 52 3D
Color <CR>$color=-#<CR>
2D 23 0D
0D 24 43 4F 4C 4F 52 3D
Color value
<CR>$color=?#<CR>
3F 23 0D
0D 24 53 48 41 52 50 3D
Sharpness +
<CR>$sharp=+#<CR>
2B 23 0D
0D 24 53 48 41 52 50 3D
Sharpness <CR>$sharp=-#<CR>
2D 23 0D
0D 24 53 48 41 52 50 3D
Sharpness value <CR>$sharp=?#<CR>
3F 23 0D
0D 24 41 53 50 3D 34 3A
Aspect 4:3
<CR>$asp=4:3#<CR>
33 23 0D
0D 24 41 53 50 3D 31 36
Aspect 16:9
<CR>$asp=16:9#<CR>
3A 39 23 0D
0D 24 41 53 50 3D 31 36
Aspect 16:10
<CR>$asp=16:10#<CR>
3A 31 30 23 0D
0D 24 41 53 50 3D 41 55
Aspect Auto
<CR>$asp=AUTO#<CR>
54 4F 23 0D
0D 24 41 53 50 3D 52 45
Aspect Real
<CR>$asp=REAL#<CR>
41 4C 23 0D
0D 24 5A 4F 4F 4D 49 23
Zoom In
<CR>$zoomI#<CR>
0D
0D 24 5A 4F 4F 4D 4F 23
Zoom out
<CR>$zoomO#<CR>
0D
Auto
<CR>$auto#<CR>
0D 24 41 55 54 4F 23 0D
0D 24 42 41 55 44 3D 32
2400
<CR>$baud=2400#<CR>
34 30 30 23 0D
0D 24 42 41 55 44 3D 34
4800
<CR>$baud=4800#<CR>
38 30 30 23 0D
0D 24 42 41 55 44 3D 39
9600
<CR>$baud=9600#<CR>
36 30 30 23 0D
0D 24 42 41 55 44 3D 31
14400
<CR>$baud=14400#<CR>
34 34 30 30 23 0D
0D 24 42 41 55 44 3D 31
19200
<CR>$baud=19200#<CR>
39 32 30 30 23 0D
0D 24 42 41 55 44 3D 33
38400
<CR>$baud=38400#<CR>
38 34 30 30 23 0D
Contrast +
<CR>$con=+#<CR>
42
Write
57600
Write
115200
Read
Read
Lamp Control
Write
Normal mode
Write
Economic mode
Write
Read
Miscellaneous
Current Baud
Rate
Equivalent lamp
hour
Dynamic Eco
mode
Lamp Mode
Status
Write
Blank On
Write
Blank Off
Read
Blank Status
Write
Freeze On
Write
Freeze Off
Read
Freeze Status
Write
Menu On
Write
Menu Off
Write
Write
Write
Up
Down
Right
Write
Left
Write
Enter
0D 24 42 41 55 44 3D 35
37 36 30 30 23 0D
<CR>$baud=115200#<CR 0D 24 42 41 55 44 3D 31
>
31 35 32 30 30 23 0D
0D 24 42 41 55 44 3D 3F
<CR>$baud=?#<CR>
23 0D
0D 24 4C 54 49 4D 3D 3F
<CR>$ltim=?#<CR>
23 0D
0D 24 4C 41 4D 50 4D
<CR>$lampm=lnor#<CR>
3D 4C 4E 4F 52 23 0D
0D 24 4C 41 4D 50 4D
<CR>$lampm=eco#<CR>
3D 45 43 4F 23 0D
0D 24 4C 41 4D 50 4D
<CR>$lampm=seco#<CR>
3D 73 45 43 4F 23 0D
0D 24 4C 41 4D 50 4D
<CR>$lampm=?#<CR>
3D 3F 23 0D
0D 24 42 4C 41 4E 4B 3D
<CR>$blank=on#<CR>
4F 4E 23 0D
0D 24 42 4C 41 4E 4B 3D
<CR>$blank=off#<CR>
4F 46 46 23 0D
0D 24 42 4C 41 4E 4B 3D
<CR>$blank=?#<CR>
3F 23 0D
0D 24 46 52 45 45 5A 45
<CR>$freeze=on#<CR>
3D 4F 4E 23 0D
0D 24 46 52 45 45 5A 45
<CR>$freeze=off#<CR>
3D 4F 46 46 23 0D
0D 24 46 52 45 45 5A 45
<CR>$freeze=?#<CR>
3D 3F 23 0D
0D 24 4D 45 4E 55 3D 4F
<CR>$menu=on#<CR>
4E 23 0D
0D 24 4D 45 4E 55 3D 4F
<CR>$menu=off#<CR>
46 46 23 0D
<CR>$up#<CR>
0D 24 55 50 23 0D
<CR>$down#<CR>
0D 24 44 4F 57 4E 23 0D
<CR>$right#<CR>
0D 24 4C 45 46 54 23 0D
0D 24 52 49 47 48 54 23
<CR>$left#<CR>
0D
0D 24 45 4E 54 45 52 23
<CR>$enter#<CR>
0D
<CR>$baud=57600#<CR>
43
Download PDF
Similar pages