SEARCH
NEXT
COYOTE® Closures & splice cases for OPGW & ADSS: Section
9
Section 9 – COYOTE®
Closures & Splice Cases for OPGW & ADSS
Table of Contents
COYOTE Closures and Splice Cases for OPGW and ADSS ................9-2
COYOTE Closures for OPGW & ADSS
COYOTE PUP for OPGW & ADSS
COYOTE RUNT for OPGW & ADSS
COYOTE Splice Case for OPGW & ADSS .............................................9-4
COYOTE Defender ...................................................................................9-5
PREVIOUS
SECTION CONTENTS
SEARCH
®
COYOTE Closures for OPGW & ADSS
The COYOTE Closure Family features durable high-density
thermoplastic shells that weigh less than their stainless
steel counterparts. For loose tube buffer type fiber, the 6.0"
x 22.0" COYOTE Closure handles up to 144 splices and the
8.5" x 22.0" COYOTE Closure handles up to 288 splices.
The smaller 6.0" x 17.0" COYOTE PUP Closure can manage up to 48 fiber splices. The compact COYOTE RUNT
Closure can manage up to 24 fiber splices.
The COYOTE PUP Closure allows future expansion
or “growth” into a COYOTE Closure with minimal cost or
disruption to the existing fibers.
Features of the COYOTE Closure and COYOTE PUP
Closure:
• For either dielectric or OPGW cables.
• High strength, low weight, low cost, nonmetallic shells.
• Permanent neoprene gasket and LOCK-TAPE™
Sealing System allow re-entry without re-entry
kits/supplies.
• Roomy buffer tube storage system and fiber
management trays allowing large bend radii.
• Fiber management system for loose tube buffer
(see table). Other versions are readily available
(see Section 1).
• End Plate System for butt splicing:
- one Blank End Plate at one end
- one Three-Section End Plate with six premolded
cable entry ports: four ports for up to 7⁄8" OD
dielectric cables (.785" max. OPGW OD) and
two ports for up to ¾" OD dielectric cables
(.660" max. OPGW OD). Drilling not required.
• Optional Three-Section Four Port End Plate is
available for cables up to 1¼" (See next page).
• Optional Future Cable Port Kits allow for adding
cables in the future without disassembling the
End Plate. Kits must be ordered and installed
during initial assembly.
-Future cable port for 7⁄8" ports will accept cables
up to .56"
-Future cable port for 1" ports will accept cables
up to .81"
-Future cable port for 1¼" ports will accept
cables up to 1"
• When adding future OPGW cables, order additional
OPGW Strain Relief Bracket Kits.
• Closures are available that can accommodate other
types of fiber optic cable.
• OPGW Strain Relief Bracket Kit provides brackets,
clamps and moisture sealing tape required for
installing two OPGW cables in End Plate.
• Splice Case Kits are available for OPGW with
stainless steel loose-tube fiber bundles, consult
factory for details.
9-2
COYOTE Closure
• Two size closures available:
- 6.0" x 22.0" (152 mm x 559 mm), accommodates
up to 4 splice trays (up to 144 splices/closure)
- 8.5" x 22.0" (216 mm x 559 mm), accommodates
up to 8 splice trays (up to 288 splices/closure).
• Both size closures have 36 count splice trays with
three 12-count elastomeric splice blocks to retain
mechanical splices or protected fusion splices.
COYOTE PUP Closure
• One small size, 6.0" x 17.0" (152 mm x 432 mm)
• Twelve-count fiber splice tray with elastomeric splice
block to retain mechanical splices or protected fusion
splices.
• Forty-eight fiber splice capacity.
COYOTE RUNT Closure
• One compact size, 8.5"W x 3"H x 14.75"L
(216 mm W x 76 mm H x 375 mm L)
• Twelve-count fiber splice tray with elastomeric
splice block to retain mechanical splices or protected
fusion splices.
• Twenty-four fiber splice capacity.
NEXT
PREVIOUS
SECTION CONTENTS
SEARCH
NEXT
COYOTE® Closures & splice cases for OPGW & ADSS: Section
9
®
COYOTE Closures for OPGW & ADSS
1. Number of fibers required now and in the future.
2. Cable size and type.
3. Structure type for mounting method.
COYOTE Closures and Splice Trays
Catalog
Number
Description (mm)
COYOTE00058
6.0" x 22.0" (152 x 559 ) COYOTE Closure Kit for OPGW. Includes closure with organizer/storage compartment
(Cat. No. 8006560); OPGW Strain Relief Bracket Kit (Cat. No. 8003296); all required supplies; plus one 36-count tray
(Cat. No. 80805514). Will accommodate up to 4 trays per closure (144 maximum splice capacity).
COYOTE00059
8.5" x 22.0" (216 x 559 ) COYOTE Closure Kit for OPGW. Includes closure with organizer/storage compartment
(Cat. No. 8006561); OPGW Strain Relief Bracket Kit (Cat. No. 8003296); all required supplies; plus one 36-count tray
(Cat. No. 80805514). Will accommodate up to 8 trays per closure (288 maximum splice capacity).
COYOTE00060
6.0" x 22.0" (152 x 559 ) COYOTE Closure Kit for dielectric cables. Includes closure with organizer/storage
compartment (Cat. No. 8006560); all required supplies plus one 36-count tray (Cat. No. 80805514). Will
accommodate up to 4 trays per closure (144 maximum splice capacity).
COYOTE00061
8.5" x 22.0" (216 x 559 ) COYOTE Closure Kit for dielectric cables. Includes closure with organizer/storage
compartment (Cat. No. 8006561); all required supplies plus one 36-count tray (Cat. No. 80805514). Will
accommodate up to 8 trays per closure (288 maximum splice capacity).
80805514
36-Count Splice Tray with Elastomer Splice Blocks for COYOTE Closure
80805110
36-Count Splice Tray with fixed
8001127
36-Count Low Profile Splice Tray
COYOTE PUP Closures
Catalog
Number
COYOTE® Closures
for OPGW & ADSS
To order, determine:
Description (mm)
8006652
6.0" x 17.0" (152 x 432) COYOTE PUP Closure for
OPGW. Includes OPGW Strain Relief Kit (Cat. No.
8003296) and one 12-count Splice Tray (Cat. No.
80806033)
8006653
6.0" x 17.0" (152 x 432) COYOTE PUP Closure for
ADSS/Buried Cables. Includes one 12-count Splice
Tray (Cat. No. 80806033)
80806033
Twelve-count Splice Tray for COYOTE PUP Closure
80807701
Twelve-count Low Profile Splice Tray
COYOTE RUNT Closures
Catalog
Number
8006695
Description
COYOTE RUNT Closure for OPGW, includes
OPGW Strain Relief Kit (Cat. No. 8003479) and one
12-count Splice Tray (Cat. No. 80806033)
COYOTE Closures and COYOTE PUP Closure Accessories
Catalog
Number
Description (mm)
80805739
Three-Section Four Port End Plate Kit
8003289
Future Cable Port/Cable Installation Kit for 7⁄8" cable ports(0.56" (14) max. cable). Kit includes Future Cable Port
(Cat. No. 8003371) and Future Cable Preparation Kit (Cat. No. 8003291) which can be ordered separately.
8003408
Future Cable Port/Cable Installation Kit for 1" cable ports(0.81" (21) max. cable). Kit includes Future Cable Port
(Cat. No. 8003407) and Future Cable Preparation Kit (Cat. No. 8003291) which can be ordered separately.
8003410
Future Cable Port/Cable Installation Kit for 1¼" cable ports(1.0" (25) max. cable). Kit includes Future Cable Port
(Cat. No. 8003409) and Future Cable Preparation Kit (Cat. No. 8003291) which can be ordered separately.
8003372
Vertical Pole/Structure Mounting Bracket Kit for COYOTE Closure and COYOTE PUP Closure
8003398
Adaptor Bracket for Hughes Brothers Bullet Shield. Bracket mounts to grounding studs on COYOTE Closure End Plate
and fastener holes in the Hughes Brothers hanger provided with the Bullet Shield. Fits COYOTE Closure and COYOTE
PUP Closure
8003092
FIBERLIGN Fusion Splice Protectors. Non-heat shrink protector closes over splice and fits snugly into elastomer splice
blocks in Splice Tray (Cat. No. 80805514) Package of 20
8003296
OPGW Strain Relief Bracket Kit
9-3
PREVIOUS
SECTION CONTENTS
SEARCH
®
COYOTE Splice Case for OPGW & ADSS
The enhanced COYOTE Splice Case with stainless steel
shells now features the convenient COYOTE Fiber Management System found in the COYOTE Closure. The COYOTE
Splice Case maintains the same air and watertight seal of
our FIBERLIGN Stainless Steel Splice Case, but at less cost.
For further information about the FIBERLIGN Stainless Steel
Splice Case check with our customer service department.
Key features of the COYOTE Splice Case include:
• For either ADSS or OPGW
• Impact and corrosion resistant stainless steel shells.
• LOCKBAR™ Sealing System allows re-entry without
re-entry kits/supplies.
• High cable pull-out strength with LOCK-TAPE™
Sealant System.
• Fiber management system for loose tube buffer
offered below. Other versions are readily available.
• 6.5" x 28" standard size (other sizes available for
up to 648 splices).
• End Plate system available with blank End Plate
at one end and one of the following:
- One blank End Plate, or
- One Three-section End Plate, field-drilled for any
size/configuration.
• Standard size Splice Case accommodates up to four
36-count Splice Trays (144 max. splice capacity).
• Blank Splice Trays with three adhesive backed
12-count Elastomeric Splice Blocks (max. 36 fiber
splices per tray)
• Elastomeric Splice Blocks firmly hold mechanical
or protected fusion splices.
• Standard Splice Case can accommodate other
types of fiber optic cables.
• Splice Case kits are available for OPGW with
stainless steel loose-tube fiber bundles.
Consult PLP for details.
Catalog
Number
9-4
Vertical Mounting
Bracket (p/n 8003472)
COYOTE Splice Case (p/n 8006684)
Fusion Splice
Protector (p/n 8003092)
Splice Tray (p/n 80805514)
Low Profile COYOTE Splice Tray
(p/n 8001127)
Description (mm)
8006654
6.5"x 28" (165 x 711) COYOTE Splice Case for ADSS or OPGW.* Includes Splice Case Kit, Green Sealant Kit (Cat.
No. 8003411), one 36-count Splice Tray (Cat. No. 80805514), one blank End Plate and one Three-Section End Plate
(field drilled for specific cable configurations and ODs) and L-Brackets for strength member tie-off.
80805514
36-count Splice Tray with Elastomeric Splice Blocks
8001127
Low Profile COYOTE Splice Tray for up to 36 fusion splices.
Protected Fusion Splice only.
8003472
Vertical Mounting Bracket for 6.5", 8" and 9.5" (165, 203, and 241) COYOTE Splice Cases. Includes two brackets
and associated hardware (curved or flat surfaces).
8003092
Fusion Splice Protector. Hinged plastic protector closes onto fusion splice area. The protector fits snugly into
elastomer splice blocks (Cat. No. 80805514). Twenty (20) units per package.
80804986
Three-Section End Plate Kit for 6.5" (165) COYOTE Splice Cases. Field drilling required.
8003421
¾" (19) Field-Installed Future Port/Cable Installation Kit [0.80" (20) max. cable]. Kit includes Future Cable Port
(Cat. No. 8003412) and Future Cable Preparation Kit (Cat No. 8003420) which can be ordered separately.
8003422
1.0" (25) Field-Installed Future Port/Cable Installation Kit [1.0" (25) max. cable]. Kit includes Future Cable Port
(Cat. No. 8003413) and Future Cable Preparation Kit (Cat No. 8003420) which can be ordered separately.
* Catalog No. 8006654 is suitable for OPGW cable with plastic loose tube buffer tubes that can be brought into the 36 count spllice trays.
Other metallic non-flexible buffer tubes may require a transition compartment. Contact PLP for more information.
NEXT
PREVIOUS
SECTION CONTENTS
SEARCH
NEXT
COYOTE® Closures & splice cases for OPGW & ADSS: Section
9
COYOTE Defender for ADSS or OPGW Fiber Optic Cable
1.
Vertical
Bracket
Component
Nomenclature:
1. Mounting Frame
2.
2. Hex Head Self Tapping
Screws, 5⁄16"x1" Long
Case & Closure Protection
COYOTE Defender Splice Case & Closure Protection
3. Adjustable Horizontal
Bracket
Hinge Bracket
Component
3.
4. Hex Head Bolt,
58
⁄ "-11x1.5" Long
5. Door
58
⁄ " Bolt Hole
Band Slot
General Information:
The COYOTE Defender provides added protection for a)
COYOTE Splice Case sizes 6.5", 8", and 9.5" up to 28" long
and b) COYOTE Closure sizes 6.0" and 8.5" - all lengths.The
Mounting Frame comes assembled from the factory. Hinge
Brackets and Ver tical Bracket components are fastened
with 5⁄16"x1" long self tapping screws. The Hinge Brackets
are positioned 19" apart to mount the 28" long COYOTE
Splice Cases. All other Splice Cases and Closures are accommodated with the Adjustable Horizontal Bracket. Two
large doors and the mounting frame surround the closure or
splice case and allow easy access for future maintenance
or expansion. The frame can be installed first, followed by
each door (each door weighs 38#) thus reducing the chore
of lifting a bulky steel unit - this makes the Lineman’s task
manageable and less hazardous.
MOUNTING OPTIONS: The COYOTE Defender can be
mounted with thru bolts, DA bolts, or banding. The frame
will accept standard 5⁄8" thru bolts and DA bolts. Use the
mounting frame as a template to locate positions for drill
through on wood pole structures. Double Arming bolts must
not extend 1.5" beyond the Hinge Bracket surface to avoid
splice case interference. Banding slots are provided in 6
positions along the frame. The band slots will accept up to
1.5" wide banding. For banding applications, 5⁄8" x 1.5" bolts
are used to provide attachment to the mounting frame.
ORDERING INSTRUCTIONS: Two catalog numbers are
available, one for COYOTE Splice Case applications, and the
other for the COYOTE Closure applications. The Defender
kit for the COYOTE SPLICE CASE (#8003491) includes
a Vertical mounting bracket kit to hang the case onto the
mounting frame of the Defender. Likewise, the Defender kit
for the COYOTE Closure (#8003492) includes an adapter
bracket kit to hang the closure onto the mounting frame of
the Defender.
4.
5.
6. Vertical Mounting
Bracket for Splice Cases
7. Adapter Bracket for
COYOTE Closures
6.
Splice Case
w/Vertical
Mounting Brackets
7.
Closure Adapter
Bracket
9-5
COYOTE® Defender Splice
®
PREVIOUS
SECTION CONTENTS
SEARCH
®
COYOTE Defender Splice Case & Closure Protection
The Adjustable Horizontal Bracket is not required for the 28"
long Splice Cases. However this bracket can be positioned
on the mounting frame to adapt the other sizes - these
positions are listed in the FRAME CONFIGURATION column
of the following table.
COYOTE Defender Catalog Numbers And Frame Configuration
Application
Type
Size (mm)
Defender
Catalog No.
6.5" X 22"
(165 X 559)
8003491
6.5" X 28", 8" X 28", 9.5" X 28"
(165 X 711, 203 X
711, 241 X 711)
8003491
6" X 17" COYOTE PUP
(152 X 432)
8003492
6" X 22", 8.5" X 22"
(152 X 559, 216 X 559)
8003492
Frame Configuration
COYOTE
Splice Case
COYOTE
Closure
Accessories:
Vertical Cable Storage Assemblies:
1) Double Arm Configuration: Order 2 ea. Cat. No. 8003493
2) Triple Spool/Single Arm: Order 1 ea. Cat No. 8003493 and 1 ea. Cat. No. 8003503
3) Banded Triple Spool/Single Arm: Order 1 ea. Cat. No. 8003493 and 1 ea. Cat. No. 8003503b1
Note: The Coyote Defender frame accepts the standard cross arm of vertical cable storage assemblies, 5⁄16 x 1 self
tapping screws lock arms into place.
9-6
NEXT
PREVIOUS
SECTION CONTENTS
SEARCH
COYOTE® Closures & splice cases for OPGW & ADSS: Section
9
Accessories:
Vertical Cable Storage Assemblies found earlier in this
section can be used with the COYOTE Defender. Large
rectangular slots at the top and bottom of the mounting
frame accept the Cable Storage Cross Arm. Catalog
Numbers for suggested configurations #1, #2, and #3 are
noted in the table.
Case & Closure Protection
COYOTE Defender Splice Case & Closure Protection
COYOTE Defender with and Without Vertical Cable Storage Accessories
Configuration #1
Configuration #2
Configuration #3
Basic Kit
Kit With Two Cable
Storage Assemblies
Kit With One Cable
Storage Assembly
and One Spool
Splice Case not included
9-7
COYOTE® Defender Splice
®
Download PDF
Similar pages