A-DU9-100-11(1)
Color Camera Module
Technical Manual
FCB-EX995E/P
FCB-EX985E/P
 2010 Sony Corporation
Table of Contents
Features ..................................................................... 3
Precautions ................................................................ 5
Locations of Controls ............................................... 7
Basic Functions ......................................................... 8
Overview of Functions ................................................ 8
Eclipse ...................................................................... 23
Spectral Sensitivity Characteristics .......................... 23
Vibration Specifications ............................................ 23
Key Switch Circuitry ................................................. 24
Key Function Specifications ..................................... 25
Initial Settings, Custom Preset and Backup ............. 28
Mode Condition ........................................................ 30
Command List ......................................................... 33
VISCA/RS-232C Commands ................................... 33
FCB Camera Commands ......................................... 39
Specifications .......................................................... 60
2
Features
Features
FCB-EX995E/P
• The EX-view HADTM CCD features 380,000 (NTSC)
or 440,000 (PAL) effective picture elements and
high-sensitivity shooting. The minimum illumination
required is 0.65 lux (1/60 s (NTSC), 1/50 s (PAL), ICR
OFF).
• A CCD for shooting a wide dynamic range is
employed to perform progressive or interlaced
scanning, and images with a wide dynamic range are
obtained by a newly developed image signal
processor (Wide Dynamic Range function).
Furthermore, it is possible to automatically switch to
this Wide Dynamic Range function, which enables
you to obtain optimal images ranging from the dark
areas of a subject to the light areas.
• Low-noise images can be obtained even in low light
environments using the 3D Noise Reduction (3D NR
+ 2D NR) function.
• A function to output interlaced or progressive images
by digital output (equivalent to ITU-R BT656) is
provided.
• The camera uses a newly developed 28× optical
zoom lens with high durability, high zoom speed, and
F1.35 brightness. (324× with digital zoom)
• A Image Stabilizer function enables stable shooting.
• Supporting external synchronization (V-lock)
• Images with a high resolution (550 TV lines) can be
obtained using a newly developed Image Signal
Processor for improved picture quality.
• An infrared (IR) Cut-Filter can be disengaged from
the image path for increased sensitivity in low light
environments. The ICR will automatically engage
depending on the ambient light, allowing the camera
to be effective in day/night environment.
• VISCA is a communications protocol, which enables
the camera to be controlled remotely from a host
computer/controller.
• Six memory locations are provided to temporally
save and recall up to six sets of camera settings.
• A Privacy Zone Masking function (max. 24 blocks) is
available.
• A mosaic masking function has been added to the
privacy zone masking function.
• A title composed of up to 11 lines can be set for
displaying on the screen. 20 characters can be used
on one line.
• E-FLIP and Mirror Image functions
• Alarm function with adjustable detection zones
• Adjustable AE response speed
FCB-EX985E/P
• The Super HAD IITM CCD features approx.380,000
(NTSC) or approx.440,000 (PAL) effective picture
elements and high-sensitivity shooting. The minimum
illumination required is 0.25 lux (1/60 s (NTSC),
1/50 s (PAL), ICR OFF).
• Low-noise images can be obtained even in low light
environments using the 3D Noise Reduction (3D NR
+ 2D NR) function.
• A function to output interlaced images by digital
output (equivalent to ITU-R BT656) is provided.
• The camera uses a newly developed 28× optical
zoom lens with high durability, high zoom speed, and
F1.35 brightness. (324× with digital zoom)
• A Image Stabilizer function enables stable shooting.
• Supporting external synchronization (V-lock)
• Images with a high resolution (550 TV lines) can be
obtained using a newly developed Image Signal
Processor for improved picture quality.
• An infrared (IR) Cut-Filter can be disengaged from
the image path for increased sensitivity in low light
environments. The ICR will automatically engage
depending on the ambient light, allowing the camera
to be effective in day/night environment.
• VISCA is a communications protocol, which enables
the camera to be controlled remotely from a host
computer/controller.
• Six memory locations are provided to temporally
save and recall up to six sets of camera settings.
• A Privacy Zone Masking function (max. 24 blocks) is
available.
• A mosaic masking function has been added to the
privacy zone masking function.
3
Features
• A title composed of up to 11 lines can be set for
displaying on the screen. 20 characters can be used
on one line.
• E-FLIP and Mirror Image functions
• Alarm function with adjustable detection zones
• Adjustable AE response speed
With consideration given environmental protection,
this module is designed to operate with low power
consumption and also incorporates lead-free and
halogen-free circuit boards.
WB Sodium Vapor
Lamp mode (sodium
vapor lamp white
balance mode)
a
a
Temperature
reading function
a
a
AGC Max Gain
Limit
a
a
Focus tracking
ON/OFF
a
a
Function List
Confirm the model name and verify its available
functions.
Main Functions
FCB-EX995E/P FCB-EX985E/P
Progressive scan
a
−
Wide dynamic range
mode (WD) (progre
ssive mode)
a
−
AF (auto focus)
a
a
AE (auto exposure
mode)
a
a
AWB (auto white
balance)
a
a
Noise reduction /
edge enhancement
(aperture)
a
a
Slow shutter
a
a
Digital zoom
a
a
Image stabilizer
a
a
Freeze
a
a
Privacy zone settings
a
a
Color enhancement
a
a
Motion detection
a
a
StableZoom
a
a
Wide dynamic range
mode (WD) (auto
mode / manual mode)
a
−
Slow AE (auto
exposure mode)
a
a
WB Outdoor Auto
(outdoor white
balance mode)
a
a
4
Features
Precautions
Software
Use of the demonstration software developed by Sony
Corporation or use of the software with customer
developed application software may damage hardware,
the application program or the camera. Sony
Corporation is not liable for any damages under these
conditions.
Operation
Start the camera control software on your computer
after you turn on the camera and the image is
displayed.
Operation and storage locations
Do not shoot images that are extremely bright (e.g.,
light sources, the sun, etc.) for long periods of time. Do
not use or store the camera in the following extreme
conditions:
• Extremely hot or cold places (operating temperature
–5 ˚C to +60 ˚C (41 ˚F to 140 ˚F))
• Close to generators of powerful electromagnetic
radiation such as radio or TV transmitters
• Where it is subject to fluorescent light reflections
• Where it is subject to unstable (flickering, etc.)
lighting conditions
• Where it is subject to strong vibration
• Where it is subject to radiation from laser beams
In case of abnormal operation, contact your authorized
Sony dealer or the store where you purchased the
product.
Phenomena specific to CCD image
sensors
The following phenomena that may appear in images
are specific to CCD (Charge Coupled Device) image
sensors. They do not indicate malfunctions.
White flecks
Although the CCD image sensors are produced with
high-precision technologies, fine white flecks may be
generated on the screen in rare cases, caused by cosmic
rays, etc.
This is related to the principle of CCD image sensors
and is not a malfunction.
The white flecks especially tend to be seen in the
following cases:
• when operating at a high environmental temperature
• when you have raised the master gain (sensitivity)
• when operating in Slow-Shutter mode
Vertical smear
When an extremely bright object, such as a strong
spotlight or flashlight, is being shot, vertical tails may
be produced on the screen, or the image may be
distorted.
Monitor screen
Vertical tails shown on the
image.
Care of the unit
Remove dust or dirt on the surface of the lens with a
blower (commercially available).
Bright object
(e.g. strong spotlight,
strong reflected light,
flashlight, the sun)
Other
Do not apply excessive voltage. (Use only the
specified voltage.) Otherwise, you may get an electric
shock or a fire may occur.
Aliasing
When fine patterns, stripes, or lines are shot, they may
appear jagged or flicker.
5
Precautions
Phenomena Specific to Lenses
Ghosting
If a strong light source (e.g., the sun) exists near the
incidence angle of the lens, bright spots may appear in
the image due to diffuse reflection within the lens.
6
Locations of Controls
Locations of Controls
Front
Top
Back
Bottom
1 Lens
2 CN503 jack
3 CN501 jack
4 CN200 jack (for digital output)
5 TELE button
6 WIDE button
7 CN702 jack (for key SW)
8 Tripod screw hole
When a tripod is used, please use
7 mm (9/32 in.) or less screw to
attach it to the camera. Also,
please be sure to attach the tripod
securely.
7
Basic Functions
Basic Functions
Overview of Functions
VISCA commands are the basis of camera control.
Timing Chart
As VISCA Command processing can only be carried
out one time in a Vertical cycle, it takes the maximum
1V cycle time for an ACK/Completion to be returned.
If the Command ACK/Completion communication
time can be cut shorter than the 1V cycle time, then
every 1V cycle can receive a Command.
General Commands
Within
In general
• Power On/Off
Powers the camera on and off. When the power is off,
the camera is able to accept only the lowest level of
VISCA Commands; the display and other features are
turned off.
• I/F Clear
Clears the Command buffer of the FCB camera.
Clearing the buffer can also be carried out from the
control application software when the power is on.
• Address Set
VISCA is a protocol, which normally supports a
daisy chain of up to seven connected cameras via RS232C interface. In such cases, the address set
command can be used to assign addresses from 1 to 7
to each of the seven cameras, allowing you to control
the seven cameras with the same personal computer.
Although the FCB camera does not support direct
connection of cameras in a daisy chain, be sure to use
the address set command to set the address whenever
a camera is connected for the first time.
• ID Write
Sets the camera ID.
Query Commands
• Mute
Blanks the screen and sends out a synchronizing
signal.
Within
• Lens Initialize
Initializes the zoom and focus of the lens. Even when
power is already on, it initializes the zoom and the
focus.
16 Byte
• Comp Scan
A pixel blemish-masking feature, which can be made
to reevaluate overall CCD pixel blemishes and mask
severely flawed pixels automatically upon receiving
the COMP SCAN command. This feature helps to
mask the flaws found in CCD imagers, even after the
camera has been powered on for some time.
8
Basic Functions
Zoom
Focus
The FCB camera employs a 28× optical zoom lens
combined with a digital zoom function; this camera
allows you to zoom up to 324×.
Focus has the following modes, all of which can be set
using VISCA Commands.
• Optical 28×, f = 3.5 to 98.0 mm (F 1.35 to F 3.7)
The horizontal angle of view is approximately 55.8
degrees (wide end) to 2.1 degrees (tele end).
Digital Zoom enlarges the center of the subject by
expanding each image in both the vertical and
horizontal directions. When 324× zoom is used, the
number of effective picture elements in each direction
reduces to 1/12 and the overall resolution deteriorates.
You can activate the zoom in the following three ways
• By pressing the TELE or WIDE buttons on the
camera itself
• Using a VISCA Command
Using Standard Mode
Using Variable Mode
There are eight levels of zoom speed.
Direct Mode
Setting the zoom position enables quick
movement to the designated position.
Digital Zoom ON/OFF
In these standard and variable Speed Modes, it is necessary
to send Stop Command to stop the zoom operation.
• The Zoom Mode supports a Combined Mode and a
Separate Mode.
Combined Mode
This is the previously existing zoom method.
After the optical zoom has reached its maximum
level, the camera switches to Digital Zoom Mode.
Separate Mode
In this mode, Optical Zoom and Digital Zoom can
be operated separately. You can use digital zoom
magnification at any time from within any level of
optical magnification.
About Continues Zoom position Reply
With ZoomDirect mode, or when zooming
according to a preset, the camera outputs zoom
position data when Continues Zoom position
Reply is set to ON via a command.
Continues Zoom position Reply: y0 07 04 69 0p
0p 0q 0q 0q 0q FF
pp: D-Zoom position
qqqq: Zoom position
• Using an external key switch board connected to
the jack for the key SW.
• Auto Focus Mode
The minimum focus distance is 10 mm at the optical
wide end and 1500 mm at the optical tele end, and is
independent of the digital zoom.
The Auto Focus (AF) function automatically adjusts
the focus position to maximise the high frequency
content of the picture in a center measurement area,
taking into consideration the high luminance and
strong contrast components.
- Normal AF Mode
This is the normal mode for AF operations.
- Interval AF Mode
The mode used for AF movements carried out at
particular intervals. The time intervals for AF
movements and for the timing of the stops can be
set in one-second increments using the Set Time
Command. The initial value for both is set to five
seconds.
- Zoom Trigger Mode
When the zoom is changed with the TELE or the
WIDE buttons, the pre-set value (initially set at 5
seconds) becomes that for AF Mode. Then, it
stops.
AF sensitivity can be set to either Normal or LOW.
- Normal
Reaches the highest focus speed quickly. Use this
when shooting a subject that moves frequently.
Usually, this is the most appropriate mode.
- LOW
Improves the stability of the focus. When the
lighting level is low, the AF function does not take
effect, even though the brightness varies,
contributing to a stable image.
• Manual Focus Mode
Manual Focus has both a Standard Speed Mode and a
Variable Speed Mode. Standard Speed Mode focuses
at a fixed rate of speed. Variable Speed Mode has
eight speed levels that can be set using a VISCA
Command.
In these standard and variable Speed Modes, it is necessary to
send Stop Command to stop the zoom operation.
• One Push Trigger Mode
When a Trigger Command is sent, the lens moves to
adjust the focus for the subject. The focus lens then
holds that position until the next Trigger Command is
input.
• Infinity Mode
The lens is forcibly moved to a position suitable for
an unlimited distance.
• Near Limit Mode
Can be set in a range from 1000 (∞) to C000 (10 mm).
Default setting: 9000h (30 cm)
9
Basic Functions
White Balance
White Balance has the following modes, all of which
can be set using VISCA Commands.
• Auto White Balance
This mode computes the white balance value output
using color information from the entire screen. It
outputs the proper value using the color temperature
radiating from a black subject based on a range of
values from 3000 to 7500K.
This mode is the factory setting.
• ATW
Auto Tracing White balance (2000 to 10000K)
• Indoor
3200K Base Mode
• Outdoor
5800K Base Mode
• One Push WB
The One Push White Balance mode is a fixed white
balance mode that may be automatically readjusted
only at the request of the user (One Push Trigger),
assuming that a white subject, in correct lighting
conditions, and occupying more than 1/2 of the
image, is submitted to the camera.
One Push White Balance data is lost when the power
is turned off. If the power is turned off, reset One
Push White Balance.
• Manual WB
Manual control of R and B gain, 256 steps each
• Outdoor Auto
This is an auto white balance mode specifically for
outdoors. It allows you to capture images with natural
white balance in the morning and evening.
• Shutter Priority 1)
Variable Shutter Speed, Auto Iris and Gain
(1/1 to 1/10,000 sec., 16 high-speed shutter speeds
plus 6 low-speed shutter speeds)
1)Flicker can be eliminated by setting shutter to
t1/100s for NTSC models used in countries with a 50 Hz
power supply frequency
t1/120s for PAL models used in countries with a 60 Hz
power supply frequency
• Iris Priority
Variable Iris (F1.35 to Close, 18 steps), Auto Gain
and Shutter speed
• Manual
Variable Shutter, Iris and Gain
• Bright
Variable Iris and Gain (Close to F1.35, 17 steps at
0 dB: F1.35, 15 steps from 0 to 28 dB)
AE – Shutter priority
The shutter speed can be set freely by the user to a
total of 22 steps – 16 high speeds and 6 low speeds.
When the slow shutter is set, the speed can be 1/30s,
1
/15s, 1/8s, 1/4s, 1/2s, 1/1s. The picture output is read at a
normal rate from the memory. The memory is updated
at a low rate from the CCD. AF capability is low.
In high speed mode, the shutter speed can be set up to
1/10,000s. The iris and gain are set automatically,
according to the brightness of the subject.
Data
NTSC (s)
PAL (s)
15
1/10000
1/10000
14
1/6000
1/6000
13
1/4000
1/3500
12
1/3000
1/2500
11
1/2000
1/1750
10
1/1500
1/1250
0F
1/1000
1/1000
0E
1/725
1/600
0D
1/500
1/425
0C
1/350
1/300
0B
1/250
1/215
0A
1/180
1/150
09
1/125
1/120
08
1/100
1/100
07
1/90
1/75
A variety of AE functions are available for optimal
output of subjects in lighting conditions that range
from low to high.
06
1/60
1/50
05
1/30
1/25
04
1/15
1/12
• Full Auto
Auto Iris and Gain, Fixed Shutter Speed (NTSC: 1/60
sec., PAL: 1/50 sec.)
03
1/8
1/6
02
1/4
1/3
01
1/2
1/2
• Gain Limit Setting
The gain limit can be set in the AE mode. Use this
setting when image signal-to-noise ratio is
particularly important.
00
1/1
1/1
• Sodium Vapor Lamp Auto
This is an auto white balance mode that is compatible
with sodium vapor lamps.
• Sodium Vapor Lamp
This is a fixed white balance mode specifically for
sodium vapor lamps.
Automatic Exposure Mode
10
Basic Functions
AE – Iris priority
The iris can be set freely by the user to 18 steps
between F1.6 and Close.
The gain and shutter speed are set automatically,
according to the brightness of the subject.
Data
Iris
Gain
Data
Iris
Gain
1F
F1.35
28 dB
0F
F2
0 dB
1E
F1.6
26 dB
0E
F2.4
0 dB
1D
F1.6
24 dB
0D
F2.8
0 dB
1C
F1.6
22 dB
0C
F3.4
0 dB
Data
Setting value
Data
Setting value
1B
F1.6
20 dB
0B
F4
0 dB
11
F1.35
08
F6.8
1A
F1.6
18 dB
0A
F4.8
0 dB
10
F1.6
07
F8
19
F1.6
16 dB
09
F5.6
0 dB
0F
F2
06
F9.6
18
F1.6
14 dB
08
F6.8
0 dB
0E
F2.4
05
F11
17
F1.6
12 dB
07
F8
0 dB
0D
F2.8
04
F14
16
F1.6
10 dB
06
F9.6
0 dB
0C
F3.4
03
F16
15
F1.6
8 dB
05
F11
0 dB
0B
F4
02
F19
14
F1.6
6 dB
04
F14
0 dB
0A
F4.8
01
F22
13
F1.6
4 dB
03
F16
0 dB
09
F5.6
00
CLOSE
12
F1.6
2 dB
02
F19
0 dB
11
F1.35
0 dB
01
F22
0 dB
10
F1.6
0 dB
00
CLOSE
0 dB
AE – Manual
The shutter speed (22 steps), iris (18 steps) and gain
(16 steps) can be set freely by the user.
AE – Bright
The bright control function adjusts both gain and iris
using an internal algorithm, according to a brightness
level freely set by the user. Exposure is controlled by
gain when dark, and by iris when bright.
As both gain and iris are fixed, this mode is used when
exposing at a fixed camera sensitivity. When switching
from Full Auto or Shutter Priority Mode to Bright
Mode, the current status will be retained for a short
period of time.
Only when the AE mode is set to “Full Auto” or
“Shutter Priority,” can you switch it to “Bright.”
Gain
IRIS AGC
OPEN MAX
IRIS curve
Gain curve
CLOSE MIN
Dark
Bright
Controlled
by gain
When switching from the Shutter Priority mode to the
Bright mode, the shutter speed set in the Shutter
Priority mode is maintained.
Spot Exposure Mode
In Full Auto AE, the level for the entire screen is
computed and the optimum Auto Iris and Gain levels
are determined. In Spot AE, a particular section of the
subject can be designated, and then that portion of the
image can be weighted and a value computed so that
Iris and Gain can be optimized to obtain an image.
For example, in an image with a lot of movement and
with varying levels of brightness, portions without
much change can be designated as such a “spot,” and
changes to the screen can be minimized in that area.
As shown in the diagram below, a range of 16 blocks
vertically and 16 blocks horizontally can be
designated.
In the case where the center is designated (shown in
black), the level is computed along with a weighted
value for the surrounding block (shaded), including the
specified portions; and then the Gain and Iris are set.
The value of the designated portions and the
surrounding areas should be calculated as 100%, the
rest should be set to 20%. The range of the Spot AE
frame is fixed to 5 blocks vertically and 4 blocks
horizontally.
Controlled by IRIS
Horizontal 16
0 1 2 3 4 5 6 7 8 9 A B C D E F
Bright limit which controllable
for this unit
Vertical 16
0
1
2
3
4
5
6
7
8
9
A
B
C
D
E
F
(8,8)
11
Basic Functions
Exposure Compensation
Aperture Control
Exposure compensation is a function which offsets the
internal reference brightness level used in the AE
mode, by steps of 1.5 dB.
Aperture control is a function which adjusts the
enhancement of the edges of objects in the picture.
There are 16 levels of adjustment, starting from “no
enhancement.” When shooting text, this control may
help by making them sharper.
Data
Step
Setting value
0E
+7
+10.5 dB
0D
+6
+9 dB
0C
+5
+7.5 dB
0B
+4
+6 dB
0A
+3
+4.5 dB
09
+2
+3 dB
08
+1
+1.5 dB
07
0
0 dB
06
–1
–1.5 dB
05
–2
–3 dB
04
–3
–4.5 dB
03
–4
–6 dB
02
–5
–7.5 dB
01
–6
–9 dB
00
–7
–10.5 dB
Slow AE (Automatic Exposure)
The slow AE Response (automatic exposure) function
allows you to reduce the exposure response speed.
Usually the camera is set up so that the optimum
exposure can be obtained automatically within about 1
second. However, using the slow AE response function
allows you to lengthen the automatic exposure
response speed from the factory setup speed (01 (hex)
up to approx. two minutes (30 (hex)).
For example, with the normal setting (about 1 second),
if the headlights of a car are caught by the camera, the
camera automatically adjusts the exposure so that it
can shoot a high-intensity subject (in this case, the
headlights). As a result, images around the headlights,
that is, the rest of the subject, except the headlights,
becomes relatively dark, and poorly distinguished.
However, using the slow AE function means the AE
response speed will be slower, and response time will
be longer. As a result, even if the camera catches a
high-intensity subject (e.g., the headlights) for a
moment, you can still easily distinguish the portions of
the image surrounding the headlights.
High Resolution Mode (Default)
Back Light Compensation
When the background of the subject is too bright, or
when the subject is too dark due to shooting in the AE
mode, back light compensation will make the subject
appear clearer.
Wide Dynamic Range Mode (WD)
The Wide Dynamic Range mode is a function for
dividing an image into several blocks and correcting
blocked-up shadows and blown-out highlights in
accordance with the intensity difference. It enables you
to obtain images in which portions ranging from dark
to light can be recognized, even when capturing a
subject with a large intensity difference that is backlit
or includes extremely light portions.
A CCD for shooting a wide dynamic range is
employed, and a newly developed image signal
processor combines a long exposure signal (normal
shutter) and a signal of the high intensity portions
obtained by a short exposure (high-speed shutter) to
achieve images with a wide dynamic range.
Wide Dynamic Range Auto On/Off Mode
The wide dynamic range can be set to be automatically
switched ON/OFF in accordance with the intensity
difference obtained by dividing an image into several
blocks and then averaging the intensity of each block.
Wide Dynamic Range Auto On/Off Mode
Auto On/Off
When the intensity
difference between the
dark portions and light
portions of a subject
becomes large because
of back lighting or the
like, the wide dynamic
range mode is switched
ON.
When the subject
changes and the
intensity difference
between the dark
portions and light
portions becomes
small, the wide dynamic
range mode is switched
OFF.
A newly developed ISP function enables the filtering
of signals. This allows the camera to provide images
with a high resolution (550 TV lines).
12
Basic Functions
The wide dynamic range mode includes the following
operation modes.
• WD Mode
This mode corrects blocked-up shadows and blownout highlights in accordance with the intensity
difference.
• WD Auto ON/OFF Mode
This mode switches WD ON/OFF automatically in
accordance with the intensity difference of the subject.
Configure the sensitivity for when WD is switched
from OFF to ON with the detection sensitivity
parameter.
• Exposure Ratio Mode
This mode fixes the shutter speed of a short exposure.
Configure the shutter speed of a long exposure by
setting the ratio with regards to a short exposure with
the exposure ratio parameter.
Blocked-up shadow correction is not performed in
this mode.
• Histogram Mode
This mode uses a histogram to correct blocked-up
shadows and blown-out highlights. (The operation is
similar to that of FCB-EX1010/P Dver.)
• About WD Set Parameter
(Command: 8x 01 04 2D 0p 0q 0r 0s 0t 0u 00 00
FF)
p: Screen display (0: Combined image, 1: Long/short
division, 2: Long-time, 3: Short-time)
Set the screen display to a WD combination
image, long/short exposure division image,
long exposure image, or short exposure image.
q: Detection sensitivity (0: Low, 1: Mid, 2: Hi)
Select from three levels for detecting the
intensity within the image for when switching
Auto WD from OFF to ON.
r:
Blocked-up shadow correction level can be
set to one of four levels. (0:L 1:M 2:H 3:S)
s:
Blown-out highlight correction level can be
set to one of three levels. (0:L 1:M 2:H)
tu:
Parameter to use in the exposure ratio mode.
Specify the short exposure time by setting
the magnification ratio (×1 to ×150) with
regards to a long exposure time.
Note
When the wide dynamic range mode is ON, solarization may be
observed in the images of some subjects. This phenomenon is
unique to wide dynamic range mode, and is not an indication of a
camera malfunction.
Noise Reduction
The NR (Noise Reduction) function removes noise
(both random and non-random) to provide clearer
images. By combining 2D filtering according to
brightness and image color, and 3D filtering according
to noise caused by motion and time difference, lower-
noise images can be obtained for the corresponding
image brightness of a moving subject.
This function has six steps: levels 1 to 5, plus off.
Level 1 applies to subject motion mainly using 2D
filter effects. With level 5, 2D and 3D filter effects are
maximized, providing the lowest-noise images,
although moving subjects may show trails.
At each level, two filters are set according to noise and
image motion characteristics, so the available level
selections depend on the situation. The default setting
is level 3.
StableZoom™
StableZoom is a function for performing correction
using the Image Stabilizer function in accordance with
the zoom ratio, and smoothly zooming up to
approximately ×31 using a combination of the optical
zoom and digital zoom. The digital zoom can be
further used to zoom up to ×432.
At the wide end, you can obtain images without any
reduction in the angle of view and resolution because
the digital zoom is not switched ON. On the other
hand, at the Tele end, the correction effect by the
Image Stabilizer function is at its maximum so blurring
is reduced.
The StableZoom function can be switched ON/OFF in
the register settings.
Blurring is corrected in this
digital zoom area.
x432
approx.
x40
StableZoom
Digital zoom
x36
Optical zoom
Zoom
ratio
The digital
zoom is not
switched ON
at the wide
end.
Wide
Optical zoom position
Tele
Angle of view and resolution
Color Enhancement
A captured color image is converted to 256 levels of
gray, and the binarization process is performed to
convert all gray levels brighter than the threshold value
to white, and all gray levels darker than the threshold
value to black. (Any value can be set for the threshold
level and hysteresis width.) Furthermore, any color can
be assigned to each of the negative and positive.
13
Basic Functions
Note
ICR (IR Cut-Removable) Mode
Flickering in images during color enhancement is not an indication
of a camera malfunction. It can be reduced with the threshold level,
hysteresis width, and edge enhancement (aperture) settings.
Grayscale image
(256 levels)
Color image
Binarization
process
Assign any
color
Image Stabilizer
Switching ON the Image Stabilizer function reduces
image blurring caused by, for example, vibration,
which allows you to obtain images without much
blurring. A correction effect of approximately 90% is
possible for a vibration frequency of around 10 Hz.
The Image Stabilizer function employs the digital
zoom system, so the angle of view and resolution are
changed, but the sensitivity is maintained.
Hold Function of Image Stabilizer
With the Image Stabilizer function, suddenly stopping
high-speed movement (pan, tilt, etc.) of the camera
produces a blur sensor counteraction that may cause
image movement. In such a case, you can use a
command setting (hold) to maintain the correction of
the Image Stabilizer function. In this case the image
stabilizer is off, but there is no change in the angle of
view.
An infrared (IR) Cut-Filter can be disengaged from the
image path for increased sensitivity in low light
environments. The ICR will automatically engage
depending on the ambient light, allowing the camera to
be effective in day/night environments.
When the auto ICR mode is set to ON, the image
becomes black and white.
Auto ICR Mode
Auto ICR Mode automatically switches the settings
needed for attaching or removing the IR Cut Filter.
With a set level of darkness, the IR Cut Filter is
automatically disabled (ICR ON), and the infrared
sensitivity is increased. With a set level of brightness,
the IR Cut Filter is automatically enabled (ICR OFF).
Also, on systems equipped with an IR light, the
internal data of the camera is used to make the proper
decisions to avoid malfunctions.
Auto ICR Mode operates with the AE Full Auto
setting.
When Auto Slow Shutter is OFF (initial setting)
ICR
AGC
MAX
Shutter 1/60 sec
IRIS
OPEN
GAIN
ICR ON
IRIS
SHUTTER
Dark
Bright
ICR OFF t ON
Temperature Reading Function
When Auto Slow Shutter is ON
The conversion value (hex) of the temperature sensor
built into to the camera can be read by using a query
command. The conversion value has an error of ±3 C,
and because the temperature sensor is inside the
camera, this value is not the ambient temperature. Use
it as a reference value.
Slow shutter – Auto/Manual
When set to “Auto,” ensures that the slow shutter is set
automatically when the brightness drops. Effective
only when the AE mode is set to “Full Auto.”
Set to “Slow Shutter Manual” at shipment.
Note
Note
The Slow Shutter Auto function is not available in WD mode.
When in Auto_ICR_OFF state and WB data is added (default), a
malfunction may occur when the subjects largely consisting of blue
and green colors are taken.
14
Basic Functions
Camera ID
The ID can be set up to 65,536 (0000 to FFFF). As this
will be memorized in the nonvolatile memory inside,
data will be saved regardless of whether it has been
backed up.
Effect
It consists of the following functions.
• Neg. Art: Negative/Positive Reversal
• Black White: Monochrome Image
Others
E-FLIP
This function turns the video output from the camera
upside down.
Mirror Image
This function reverses the video output from the
camera horizontally.
Freeze
This function captures an image in the field memory of
the camera so that this image can be output
continuously.
Because communication inside the camera is based on V
cycle, the captured image is always the one 3V to 4Vs after
the sending of a Command. Thus, you can not specify a time
period after sending EVEN, ODD or a Command.
Memory (Position preset)
Using the position preset function, 6 sets of camera
shooting conditions can be stored and recalled.
This function allows you to achieve the desired status
instantly, even without adjusting the following items
each time.
• Zoom Position
• Digital Zoom On/Off
• Focus Auto/Manual
• Focus Position
• AE Mode
• Shutter control parameters
• Bright Control
• Iris control parameters
• Gain control parameters
• Exposure Compensation On/Off
• Exposure Level
• Backlight Compensation On/Off
• Slow Shutter Auto/Manual
• Slow AE Response speed
• White Balance Mode
• R/B Gain
• Aperture
• ICR Shoot On/Off
• WD On/Off
Custom Preset
As with the position preset function, the camera
shooting conditions can be stored and recalled. The
settings are recalled when the power is turned on.
For setting items, see the “Initial Settings, Custom
Preset and Backup” section on page 28.
User Memory Area
A user area of 16 bytes allows you to write data, such
as an ID for each customer, data for each system, and
so on, freely.
Note
Rewriting of memory is not unlimited. Be careful to avoid using
the memory area for such as unnecessary tasks as rewriting the
contents of the memory for every operation.
Register Setting
The camera’s default settings can be changed by the
register setting command.
Register Setting Command:
8x 01 04 24 mm 0p 0q FF
mm: Register No. (=00 to 7F)
pq: Register Value (=00 to FF)
Register Inquiry Command:
8x 09 04 24 mm FF
mm: Register No.
y0 50 0p 0p FF
pp: Register Value
(returned from the camera)
Example: To set communication speed to 38400 bps
8x 01 04 24 00 00 02 FF
After sending this command, turn power off and
back on (power reset) to resume communication
control at 38400 bps.
Example: Sending to confirm settings
8x 09 04 24 00 FF
y0 50 00 03 FF is returned from the camera
The register setting items and No. are as follows.
Baud Rate: 00
Communication speed can be changed.
OSD Language: 60
OSD Language can be changed.
CCD Scanning Mode: 72
CCD scanning mode can be changed.
Digital Output Mode: 73
The FCB camera supports various output modes.
This register “73” allows changing the output
mode.
For details, see “Register Setting” on page 59.
Zoom Limit: 50 (Wide end), 51 (Tele end)
The Wide and Tele zoom limits can be set.
E-Zoom Max: 52
The maximum digital zoom limit can be specified
(default is ×12).
StableZoom: 53
The StableZoom command can be enabled and
disabled with this command.
15
Basic Functions
FocusTrace: 54
When zoom speed is given priority, using the
ZoomDirect command changes focus at high speed
(although the image may be blurred because focus
is not tracked). For example, the focus transition
time from Wide to Tele ends, which typically takes
2.8 seconds, can be reduced to 2 seconds.
FocusOffset: 55
Placing a dome cover in front of the camera may
cause the focal distance of the camera to change.
Especially at the Tele end, this effect exceeds the
AF range, so focus cannot track, although it
responds to changes in this value.
For details, see “Register Setting” on page 59.
• You can set a title composed of up to 11 lines. One
line can contain up to 20 characters.
• You can set display on/off, the horizontal position of
the first character, blinking state and color for each
line.
• The camera gives priority to lines of a title when the
camera status is displayed on the relevant line. On the
lines where a title is not set, the camera status is
displayed.
Line Number
00 to 0A
H-position
00 to 17
00: Does not blink
Blink
01: Blinks
02
03
00
White
01
Yellow
02
Violet
03
Red
04
Cyan
05
Green
06
Blue
04
05
06
07
B
C
D
E
F
G
H
09
0a
0b
0c
0d
0e
0f
I
J
K
L
M
N
O
P
10
11
12
13
14
15
16
17
Q
R
S
T
U
V
W
X
18
19
1a
1b
1c
1d
1e
1f
?
!
1
2
23
24
25
26
27
Z
&
21
22
8
9
0
28
29
2a
2b
2c
2d
2e
2f
À
È
Ì
Ò
Ù
Á
É
Í
30
31
32
33
34
35
36
37
Ó
Ú
Â
Ê
Ô
Æ
Œ
Ã
38
39
3a
3b
3c
3d
3e
3f
Õ
Ñ
Ç
ß
Ä
Ï
Ö
Ü
40
41
42
43
44
45
46
47
Å
$
F
¥
DM
£
¿
¡
48
49
4a
4b
4c
4d
4e
4f
ø
“
:
‘
.
,
/
-
• External synchronization (V-Lock Synchronization 1))
When a TTL level V-Lock pulse is input, the camera
synchronizes to the input signal (V-lock
synchronization). The frequency of the input signal
synchronizes to within ±1Hz of the external
synchronization.
Also, 360 degree phase adjustment is possible due to
the phase adjustment of the V-lock signal.
When adjusting V-Phase, first make the phase
adjustment with the Line Lock mode, then switch to
Frequency Lock mode and enable external sync. If
not performing phase adjustment, switch to
Frequency Lock mode then enable external sync. See
“Command List” on page 33.
Noise may occur when performing phase adjustment
with the Line Lock mode, although it should
disappear when switching to Frequency Lock mode
for external sync.
A
Y
7
Note
08
20
6
• Internal synchronization
An internal vibrator inside the camera generates a
synchronizing signal as a basic oscillator.
NTSC=59.94 Hz
PAL=50 Hz
Title Display
01
5
Internal and external synchronization are available;
VISCA Commands allow you to switch between them.
Motion detection
For details, see page 21.
00
4
Synchronization methods
Privacy Zone Settings
For details, see page 17.
Color
3
Because V-lock synchronization is a simple synchronization
method, color signals like a VBS “Genlock” signal cannot be
synchronized.
1)In V-lock synchronization, the camera makes a V-lock pulse
(VL-PULSE) which synchronizes to the commercial power
supply and uses it as the external synchronization input signal
of the camera, using the fact that the V cycle (59.97 Hz vertical
synchronization signal) and the frequency of the commercial
power supply (60 Hz). The synchronous signal of the camera
will automatically sychronizes to the VL-PULSE in the
camera.
16
Basic Functions
Privacy Zone Masking Function
Features
Privacy Zone masking protects private objects and
areas such as house windows, entrances, and exits
which are within the camera’s range of vision but not
subject to surveillance.
Privacy zone masking can be masked on the monitor to
protect privacy.
• Mask can be set on up to 24 places according to Pan/
Tilt positions.
• Mask can be displayed on 8 places per screen
simultaneously.
• Privacy Zones are displayed according to priority in
alphabetical order.
• Individual on/off zone masking settings.
• Two colors can be individually set for each of 24
privacy zones.
• Interlocking control with zooming.
• Interlocking control with Pan/Tilt.
• Non-interlocking control with Pan/Tilt.
Timing chart
8x 01 .. .. FF
(Mask Setting Command)
1V
Setting command is reflected
at this timing.
17
Basic Functions
Privacy Zone Setting Command List
Command Set
Command
Command Packet
CAM_PrivacyZone
SetMask
8x 01 04 76 mm nn
0r 0r 0s 0s FF
Setting Mask(Size)
See “mm: Mask setting list”, “nn: Setting”, and
“pp: x, qq:y, rr: w, ss: h” in “Parameters” on
page 19.
Display
8x 01 04 77 pp pp pp pp FF
Setting Mask Display On/Off
See “pp pp pp pp: Mask bit” in “Parameters”
on page 19.
pp pp pp pp: Mask setting (0: OFF, 1: ON)
SetMaskColor
8x 01 04 78 pp pp pp pp qq rr FF
Setting Color of Mask
See “pp pp pp pp: Mask bit” and “qq, rr: Color
code” in “Parameters” on page 19.
qq: Color setting when setting the Mask bit
to 0
rr: Color setting when setting the Mask bit
to 1
SetPanTiltAngle
8x 01 04 79 0p 0p 0p 0q 0q 0q FF
Setting Pan/Tilt Angle
See “Setting pan/tilt angle” in “Parameters” on
page 19.
ppp: Pan angle, qqq: Tilt angle
SetPTZMask
8x 01 04 7B mm 0p 0p 0p
0q 0q 0q 0r 0r 0r 0r FF
Setting the direct position of PTZ
See “mm: Mask setting list” and “Setting pan/
tilt angle” in “Parameters” on page 19.
ppp: Pan, qqq: Tilt, rrrr: Zoom
Comments
Non_InterlockMask 8x 01 04 6F mm
0p 0p 0q 0q 0r 0r 0s 0s FF
Setting non-interlocking the mask to pan/tilt
See “mm: Mask setting list” and “pp:x, qq:y,
rr:w, ss:h” in “Parameters” on page 19.
Grid On
Setting Grid Display On/Off
8x 01 04 7C 02 FF
Grid Off
8x 01 04 7C 03 FF
CenterLineOn
8x 01 04 7C 04 FF
Setting the center line On
Privacy Zone Inquiry Command List
Inquiry Command Command Packet
Inquiry Packet
CAM_Privacy
DisplayInq
8x 09 04 77 FF
y0 50 pp pp pp pp FF
Inquiry about the status of Setting Mask
Display On/Off
See “pp pp pp pp: Mask bit” in “Parameters”
on page 19.
1:On, 0:Off
CAM_PrivacyPan
TiltInq
8x 09 04 79 FF
y0 50 0p 0p 0p 0q 0q 0q FF
Inquiry about the pan/tilt position currently set
See “Setting pan/tilt angle” in “Parameters” on
page 19.
ppp: Pan, qqq: Tilt
CAM_Privacy
PTZInq
8x 09 04 7B mm FF y0 50 0p 0p 0p 0q 0q 0q 0r 0r
0r 0r FF
CAM_Privacy
MonitorInq
8x 09 04 6F FF
y0 50 pp pp pp pp FF
Comments
Inquiry about pan/tilt/zoom position at the mm
Mask setting
See “mm: Mask setting list” and “Setting pan/
tilt angle” in “Parameters” on page 19.
ppp: Pan Position,
qqq: Tilt Position
rrrr: Zoom Position
Inquiry about the mask currently displayed
See “pp pp pp pp: Mask bit” in “Parameters”
on page 19.
18
Basic Functions
Parameters
mm: Mask setting list
nn:Setting
Mask Name
mm (Hex)
Mask Name
Mask_A
00h
Mask_B
01h
Mask_C
mm (Hex)
nn
Setting
Mask_M
0Ch
00
Mask_N
0Dh
Resetting the zone size (the value of w,h)
for the existing mask.
02h
Mask_O
0Eh
01
Mask_D
03h
Mask_P
0Fh
Setting newly the zone size (the value of
w,h).
Mask_E
04h
Mask_Q
10h
Mask_F
05h
Mask_R
11h
Mask_G
06h
Mask_S
12h
Mask_H
07h
Mask_T
13h
Mask_I
08h
Mask_U
14h
Mask_J
09h
Mask_V
15h
Mask_K
0Ah
Mask_W
16h
Mask_L
0Bh
Mask_X
17h
pp: x, qq: y, rr: w, ss: h
160
3Ch
mask
h w
0 (x,y)
120
Note
B0h
50h
The priority order of the mask display is in the sequence from A
(highest) to X (lowest).
When you set the parameters of masks non-sequentially, it is
recommended that you set the mask whose priority order is higher,
first.
C4h
Effective display area
pp pp pp pp: Mask bit
pp
pp
pp
pp
bit
7 6 5 4 3 2 1 0 7 6 5 4 3 2 1 0 7 6 5 4 3 2 1 0 7 6 5 4 3 2 1 0
Mask
- - X W V U T S - - R Q P O N M - - L K J I H G - - F E D C B A
The “-” must be “0”.
Setting pan/tilt angle
qq, rr: Color code
Mask (Color)
Code (qq, rr)
Semi-transparency (qq, rr)
Black
00h
10h
Gray1
01h
11h
Gray2
02h
12h
-180
-90
800h
C00h
Gray3
03h
13h
Gray4
04h
14h
Gray5
05h
15h
Gray6
06h
16h
White
07h
17h
Red
08h
18h
Green
09h
19h
Blue
0Ah
1Ah
Cyan
0Bh
1Bh
Yellow
0Ch
1Ch
Magenta
0Dh
1Dh
Mosaic
7Fh
–
Angle/Parameter of Angle (ppp, qqq)
0
90
180
400h
800h
Set the angle resolution to 360 (degree)/4096 (1000h).
19
Basic Functions
Details of Setting Commands
Set Mask
Command: 8x 01 04 76 mm nn 0r 0r 0s 0s FF
Parameters:
mm
Setting Mask
See “mm: Mask setting list” in “Parameters” on page 19.
nn
Selects new setting or resetting for the zone.
See “nn: Setting” in “Parameters” on page 19.
rr
Sets the half value “w” of the Mask Width.
ss
Sets the half value “h” of the Mask Height.
See “pp: x, qq: y, rr: w, ss: h” in “Parameters” on page 19.
Comments: To set the mask, first display the object
at the center of the screen. When “nn” is set to 1,
the current Pan/Tilt/Zoom position is recorded in
internal memory.
When “nn” is set to 0, the Pan/Tilt/Zoom position
in memory is not changed.
Notes
• The tilt angle at which you can set the mask is between –70 to
+70 degrees.
• It is recommended that you set the size to at least twice the size
of the object (height and width).
Set Display
Command: 8x 01 04 77 pp pp pp pp FF
Parameter:
Comments: Two different color masks can be
chosen.
The colors can be chosen from among 14 colors
including the possibility for semi-transparency of
each color. Therefore two colors from among the
total of 29 colors including mosaic can be
individually set for each of 24 privacy zones.
If the bit of parameter (pp pp pp pp) is set to “0”,
mask color will be “qq” color (Color code). If the
bit of parameter (pp pp pp pp) is set to “1”, the
mask color will be “rr” color (Color code).
Example: 8x 01 04 78 00 00 00 03 10 07 FF
The mask color of Mask_A and Mask_B is White
(color code 07h), and the mask color of the other
Mask (C to X) is semi-transparent Black (color
code 10h).
Set Pan Tilt Angle
Command: 8x 01 04 79 0p 0p 0p 0q 0q 0q FF
Parameter:
ppp
Pan Angle
qqq
Tilt Angle
See “Setting pan/tilt angle” in “Parameters” on
page 19.
Comments: Pan/Tilt angle settings are hexadecimal
data.
The resolution of Pan/Tilt angle is 0.088 degrees.
Note
pp pp pp pp Each 24 Privacy Zones corresponds to 1 bit.
See “pp pp pp pp: Mask bit” in “Parameters” on
page 19.
Comments: Each of 24 Privacy zones can be
switched on and off individually by a single
VISCA command. If you want to display a
Privacy zone, you must set its bit to 1. If you do
not want to display a Privacy zone, you must set
its bit to 0.
Set Mask Color
Command: 8x 01 04 78 pp pp pp pp qq rr FF
Parameter:
pp pp pp pp Each 24 Privacy Zones correspond with the BIT.
See “pp pp pp pp: Mask bit” in “Parameters” on
page 19.
qq
Set the color code include the semi-transparency
code.
rr
Set the color code include the semi-transparency
code. See “qq, rr: Color code” in “Parameters” on
page 19.
When you set the pan/tilt angle, locate the pan/tilt position at the
center point of the FCB camera’s position.
Set PTZ Mask
Command: 8x 01 04 7B mm 0p 0p 0p 0q 0q 0q 0r 0r
0r 0r FF
Parameter:
mm
Setting Mask
See “mm: Mask setting list” in “Parameters” on page 19.
ppp
Pan Angle (000 to FFF)
See “Setting pan/tilt angle” in “Parameters” on page 19.
qqq
Tilt Angle (000 to FFF)
See “Setting pan/tilt angle” in “Parameters” on page 19.
rrrr
Zoom Position (000 to 4000)
See “Zoom Ratio and Zoom Position (for reference)” on
page 57.
Comments: Mask can be set at the desired position
by setting the pan tilt angle and zoom position
using this command. The set value can be input by
hexadecimal number.
20
Basic Functions
Non Interlock Mask
Command: 8x 01 04 6F mm 0p 0p 0q 0q 0r 0r 0s 0s
FF
Parameters:
mm
Setting Mask
See “mm: Mask setting list” in “Parameters” on page 19.
pp
Sets the center position “x” of the Mask on screen.
qq
Sets the center position “y” of the Mask on screen.
rr
Sets the half value “w” of the Mask Width.
ss
Sets the half value “h” of the Mask Height.
See “pp: x, qq: y, rr: w, ss: h” in “Parameters” on page 19.
Commands: Mask does not interlock with pan/tilt.
The limitations of parameters are as follows.
(hexadecimal representation)
x: ±50h
w: ±50h
y: ±3ch
h: ±3ch
Note
When the Set Mask command and the Non Interlock Mask
command are set to the same mask, the command set later
becomes effective.
Motion Detection Function
This function instructs the camera to detect movement
within the monitoring area and then send an alarm
signal automatically.
The Detect signal goes out through the serial command
(VISCA) communication line.
Features
• You can set a frame for the detection range of 12
(horizontally) × 8 (vertically) blocks.
• You can set up to four frames.
• When the motion is detected in the set frame, the
Alarm Replay VISCA command is sent.
• The threshold level for detection can be set (common
to four frames).
• The interval of alarm detection can be set up to 256
seconds in units of one second.
• You can set on/off for each frame.
• The frame number is also sent with Alarm Replay to
report in which frame the motion has been detected.
Frames
Grid
Use the grid displayed on the screen to set mask
positions (see the figure below).
By executing the Center Line On command, only the x
and y axes of the center are displayed. Grids lines
disappear.
14hex (20(10))
Setting frames
You can set the frame by assigning the starting point
and terminating point vertically and horizontally. You
can set up to four frames.
When motion is detected within the rage
where frames overlap
The alarms are sent for both frames.
14hex (20(10))
Frame 1
Frame 2
Frame 3
Frame 4
At this position, the
alarm for frame 3 is
sent.
Within this overlapped
range, alarms are sent for
both frame 3 and frame 4.
21
Basic Functions
• When multiple motions are detected or motion is
detected in another frame within the set interval
following the original time the alarm was issued,
another alarm command is not issued.
• When motion is detected after the interval time
elapsed, the alarm is issued again.
Sending Alarms
• When motion is detected, the Alarm Replay
command is issued via the serial command (VISCA)
communication line.
Alarm issue
Alarm issue
Interval
Alarm issue
Interval
Alarm issue
Interval
Alarm interval
Motion is Motion is Motion is
Motion is
detected detected detected
detected
in frame 1. in frame 1. in frame 1. in frame 1.
Setting Commands
• MD On/Off
The Display mode is selected by the Function Set
command and frames are set by the Frame Set
command. By sending an MD On command, the
frame is displayed when motion is detected in the set
frame. The Alarm Reply command is set via the
serial command (VISCA) communication line.
8x 01 04 1B 02 FF --- On
8x 01 04 1B 03 FF --- Off
• Function Set
Select the detected frame, and set the Threshold
Level and the Interval Time.
8x 01 04 1C 0m 0n 0p 0q 0r 0s FF
m: Display Mode
on/off (bit0: Frame)
n: Detection Frame set on/off (bit0:Frame0,
bit1:Frame1, bit2:Frame2, bit3:Frame3)
-- (0 to F)
pq: Threshold
-- (00 to FF)
rs: Interval time set
-- (00 to FF)
(When pq and rs are 0, the command is received, but
the setting is disabled.)
Motion is Motion is Motion is
detected
detected
detected
in frame 1. in frame 2. in frame 3.
Motion is
detected
in frame 3.
• Frame Set
You can set up to four frames by assigning the
starting and terminating points.
Note
Set a terminating point higher vertically and
horizontally than the starting point. If you set the
wrong value, the command yields an error.
8x 01 04 1D 0m 0p 0q 0r 0s FF
m: Select Detection Frame (0: Frame0, 1: Frame1, 2:
Frame2, 3: Frame3)
-- (0, 1, 2, 3)
p: Frame set Start Horizontal Position -- (00 to 0B)
q: Frame set Start Vertical Position
-- (00 to 07)
r: Frame set End Horizontal Position
-- (01 to 0C)
s: Frame set End Vertical Position
-- (01 to 08)
• Alarm Reply
When motion is detected in the set frame, the camera
issues this command. This command includes the
information on the number of the detected frame.
y0 07 04 1B 0p FF
p: Frame Number (bit0: Frame0, bit1: Frame1, bit2:
Frame2, bit3: Frame3)
22
Basic Functions
Eclipse
When designing the housing, refer to the dimensional
allowance as shown in the figure below.
Use the graph as a reference value. (We can not
guarantee these values.)
This data is measured when the IR cut filter is removed
and the characteristics of the lens and optical source
characteristics are ignored.
Vibration
Specifications
Test Method (Random vibration)
• Fix the camera at the four fixation points of the base
using M2 screws.
• Perform the random vibration test under the
following conditions in the X, Y and Z directions for
20 minutes in each direction.
• The camera vibration specification is to have no
malfunction after this test.
4.14 m2/s3
Power spectrum density 5 to 50 Hz
50 to 100 Hz –36 dB/oct
Spectral Sensitivity
Characteristics
Effective overall value
14.3 m/s2
Test time
20 minutes
{0.043 G2/Hz}
{1.46 G}
FCB-EX995E/P
FCB-EX985E/P
23
Basic Functions
Key Switch Circuitry
The circuitry shown below is an example. Note that all
switches in the figure do not function in all models.
For more information, refer to the command list, check
functions on the camera, or contact your Sony dealer.
The CN101 is connected to the FCB camera main unit.
24
Basic Functions
Key Function Specifications
Classification
Name
Function
Button operation
Mode display
ZOOM
WIDE FAST
Move ZOOM to WIDE side quickly.
Pressing repeatedly allowed.
ZOOM bar displayed
for 3 s.
WIDE SLOW Move ZOOM to WIDE side slowly.
Pressing repeatedly allowed.
ZOOM bar displayed
for 3 s.
TELE FAST
Move ZOOM to TELE side quickly.
Pressing repeatedly allowed.
ZOOM bar displayed
for 3 s.
TELE SLOW
Move ZOOM to TELE side slowly.
Pressing repeatedly allowed.
ZOOM bar displayed
for 3 s.
AF ON/OFF
Switch between Auto Focus and Manual Focus.
Switch between Auto and
Manual.
Manual F indication
NEAR
Move focus to NEAR side in Manual Focus
mode.
Pressing repeatedly allowed.
Near indication
FAR
Move focus to FAR side in Manual Focus mode. Pressing repeatedly allowed.
Far indication
ONE PUSH
AF
Perform AF operation once in Manual Focus
mode.
Request One Push AF.
Manual F indication
flashes while request
is made.
INFINITY
Move focus forcibly to Infinity resulting in
Manual Focus mode, regardless of the current
focus mode.
Request Infinity.
Far indication
AE AUTO
Switch to AE FULL Auto mode.
Request AE Full Auto.
No display
BRIGHT
Switch to variable brightness mode (BRIGHT),
depending on the conditions for mode shifting.
Request Bright mode.
Pressing Up/Down key
repeatedly allowed.
Bright bar display
SHUTTER
Shutter priority AE mode
Request shutter priority AE
mode.
Pressing Up/Down key
repeatedly allowed.
Shutter code display
IRIS
Iris priority AE mode
Request iris priority AE
mode.
Pressing Up/Down key
repeatedly allowed.
Iris code display
BACK
LIGHT
Switch backlight on/off in AE FULL Auto mode. Switch on/off.
Backlight indication
EXP COMP
ON/OFF
Switch the exposure compensation function ON/ Switch on/off.
OFF.
Exposure
compensation code
display
EXP COMP
UP
Increase the exposure compensation (UP).
(Used during exposure compensation mode. 1.5
dB increments.)
Request UP / pressing
repeatedly allowed.
Exposure
compensation code
display
EXP COMP
DOWN
Decrease the exposure compensation (DOWN).
(Used during exposure compensation mode. 1.5
dB increments.)
Request DOWN / pressing
repeatedly allowed.
Exposure
compensation code
display
WD ON/OFF
Switch the Wide Dynamic Range mode ON/
OFF.
Switch on/off.
WDR character
display
AUTO WD
ON/OFF
Switch the Auto Wide Dynamic Range mode
ON/OFF.
Switch on/off.
WDR character
display when WD is
ON.
FOCUS
AE
WD
25
Basic Functions
Classification
Name
Function
Button operation
Mode display
WB
AUTO WB
Switch to AUTO WB mode.
Request Auto WB mode.
No display
ONE PUSH
WB
Switch to One Push WB mode when pressed
once and capture data when pressed 2nd time.
Request One Push WB mode One Push indication
and trigger.
flashes at 0.8 Hz
before capturing data,
at 3.2 Hz during
capturing, and stays lit
after capturing.
ATW
Switch to ATW mode.
Request ATW mode.
ATW display
INDOOR
Enable WB at 3200K in INDOOR mode.
Request Indoor mode.
Indoor indication
OUTDOOR
Enable WB at 5800K in OUTDOOR mode.
Request Outdoor mode.
Outdoor indication
MANUAL
WB
Switch to Manual WB mode.
Enable R control when pressed once and enable
B control when pressed 2nd time. Switchable
with UP/DOWN key.
Switch between R control
and B control in manual WB
mode. Pressing Up/Down
key repeatedly allowed.
“WB-MAN”
(character display)
FREEZE
Capture still image.
Switch on/off.
CAPTURE indication
LR
REVERSE
Horizontal reversal
Switch on/off.
Horizontal reversal
indication
E-FLIP
Turn upside down
Switch on/off.
Turn upside down mark
BLACK &
WHITE
Black-and-white output
Switch on/off.
B&W display
NEGA ART
Negative art output
Switch on/off.
Neg Art display
MUTE
Muting video output
Switch on/off.
No display
DISPLAY
Display
Switch on/off.
Display/no display
TITLE
Title setting
Request setting. t Setting
is started with Exec.
Pressing Up/Down key
repeatedly allowed.
Title setting screen
display
EXEC
Confirm title setting.
Select with Up/Down and
confirm with Exec.
Sets screen selection and
displays it in yellow.
UP
Data UP key (priority for AE mode, Bright,
manual WB, title, and clock)
Request UP.
Selection highlighted.
DOWN
Data DOWN key (priority for AE mode, Bright,
manual WB, title, and clock)
Request DOWN.
Selection highlighted.
POS0
Recall preset position 0.
Request recall.
RECALL POS0
POS1
Recall preset position 1.
Request recall.
RECALL POS1
POS2
Recall preset position 2.
Request recall.
RECALL POS2
POS3
Recall preset position 3.
Request recall.
RECALL POS3
POS4
Recall preset position 4.
Request recall.
RECALL POS4
POS5
Recall preset position 5.
Request recall.
RECALL POS5
CUSTOM
Recall custom preset.
Request recall.
RECALL
FEATURE
DISPLAY
UP/DOWN
PRESET
POS PRESET Write data.
Request setting. Enabled
Enabled when pressed together with POS button. when pressed together with
POS key.
PRESET display
POS RESET
RESET display
Delete data.
Request deletion. Enabled
Enabled when pressed together with POS button. when pressed together with
POS key.
26
Basic Functions
Classification
Name
Function
Button operation
Mode display
Others
APERTURE
UP
Increase aperture (Aperture UP)
Request UP.
Aperture bar displayed
for 3 s.
APERTURE
DOWN
Decrease aperture (Aperture DOWN)
Request DOWN.
Aperture bar displayed
for 3 s.
BRIGHT UP
Raise brightness setting (Bright UP)
Request UP./Pressing
(When not in Bright mode, switching to Bright mode repeatedly allowed.
is made automatically depending on the conditions.)
Bright bar display
BRIGHT
DOWN
Lower brightness setting (Bright DOWN)
Request DOWN./Pressing
(When not in Bright mode, switching to Bright mode repeatedly allowed.
is made automatically depending on the conditions.)
Bright bar display
FUNCTION
AUTO SLOW Switch Auto Slow Shutter on/off.
SHUTTER
Switch on/off.
“ASS” (character
display)
ICR ON/OFF
Switch on/off.
ICR indication
STABILIZER Switch the Image Stabilizer function ON/OFF.
ON/OFF
Switch on/off.
Image Stabilizer
“OFF” mark
POWER ON/
OFF
Switch the POWER (Standby) ON/OFF.
Switch on/off.
–
FUNCTION1
–
–
–
FUNCTION2
–
–
–
FUNCTION3
–
–
–
Switch ICR mode on/off
27
Basic Functions
Initial Settings, Custom Preset and Backup
Initial settings for the various functions of the FCB
camera are indicated in the “Initial settings” column.
The “Custom preset” column indicates whether the
custom preset function can be used to store the
settings. The function enables the stored settings to be
recalled automatically when the camera is turned on.
The “Back up at standby” column indicates whether
the data is preserved even when the camera is powered
OFF.
Mode/Position setting
Zoom Position
Initial settings
Custom
preset
Back up
at standby
Wide end
a
a
On
a
a
Combine
a
a
D-Zoom Position
00h
a
a
Focus Position
—
a
a
Focus Auto/Manual
Auto
a
a
Near Limit Setting
D-Zoom On/Off
D-Zoom Separate/Combine
9000h (30 cm)
a
a
AF Sensitivity
Normal
a
a
AF Mode
Normal
a
a
AF Run Time
5 sec
a
a
AF Interval
5 sec
a
a
WB Mode
Auto
a
a
WB Data (Rgain, Bgain)
—
a
a
One Push WB Data
—
a
a
Full Auto
a
a
AE Response
01
a
a
WD On/Off/Auto
Off
a
a
AE Mode
Manual
a
a
1/60sec (NTSC), 1/50sec (PAL)
a
a
Iris Position
—
a
a
Gain Position
—
a
a
Bright Position
—
a
a
Exposure Compensation On/Off
Off
a
a
Exposure Compensation Amount
±0
a
a
BackLight On/Off
Off
a
a
Spot AE On/Off
Off
a
a
X=8, Y=8
a
a
6
a
a
High Resolution Mode On/Off
On
a
a
LR Reverse On/Off
Off
a
a
Freeze On/Off
Off
×
×
Picture Effect
Off
a
a
ICR On/Off
Off
a
a
Auto ICR On/Off
Off
a
a
Auto ICR Threshold Level
0Ah
a
a
Slow Shutter Mode
Shutter Position
Spot AE Position Setting
Aperture Level
A circle “a” in this column signifies that the data is preserved.
A cross “×” signifies that the data IS NOT preserved.
28
Basic Functions
Custom
Back up
preset
at standby
Same as the initial value setting
a
a
Display On/Off
Off
a
a
Mute On/Off
Off
×
×
WD Alarm On/Off
Off
×
a
Auto ICR Alarm On/Off
Off
a
a
Image Stabilizer On/Off/Hold
Off
a
a
NR Level
3
a
a
Gain Limit
—
a
a
Color Enhancement On/Off
Off
a
a
Title Display On/Off
Off
a
a
Title Setting
—
a
a
Mask Setting
—
a
a
Mask Display On/Off
Off
a
a
Mask Color Setting
—
a
a
Grid/Center Line Display On/Off
Off
a
a
Alarm On/Off
Off
a
a
Alarm Mode
—
a
a
Alarm Detect Level
—
a
a
E-Flip On/Off
Off
a
a
Privacy Zone On/Off
Off
a
a
Privacy Zone Setting
—
a
a
Key Lock On/Off
Off
a
a
Mode/Position setting
Camera Memory
Initial settings
0000h
a
a
Internal
a
a
Vsync edge position
a
a
—
a
a
MD On/Off
Off
a
a
MD Display Setting
Off
a
a
MD Threshold Level
10h
a
a
MD Interval
1 sec
a
a
—
a
a
ZoomPos Continuous Output On/Off
Off
×
a
ZoomPos Continuous Output Interval
3Ch
×
a
Camera ID
External Lock Mode
V-Phase
Alarm DayLight Threshold Level
MD Window Setting
A circle “a” in this column signifies that the data is preserved.
A cross “×” signifies that the data IS NOT preserved.
Note
The number of times written to EEPROM (when Custom Preset is executed) is limited.
29
a
a
Power On/Off
Initializing
×
×
×
×
×
×
Zoom Direct
Zoom Focus Direct
×
×
×
×
Lens Initialize
Comp Scan
* × during recalling from key
×
×
×
×
Camera Memory Set/Reset
Camera Memory Recall
×
×
×
×
AF Mode Norm/Interval/Zoom
×
×
AF Sensitivity Normal/Low
AF Activation Time/Interval Setting
×
×
×
×
Focus Infinity
×
×
×
×
Focus Auto/Manual
One Push AF
Focus Near Limit
×
×
×
×
Focus Far/Near/Stop
Focus Direct
×
×
D-Zoom Direct
×
×
×
×
D-Zoom Tele/Wide/Stop
D-Zoom ×1/Max
×
×
×
×
D-Zoom On/Off
D-Zoom Separate/Combine
Zoom Tele/Wide/Stop
Power Off
Mode
Lens
a
a
a
a
a
a
IF_Clear
Initializing
Power Off
Command Cancel
Address Set
Mode
Condition
Mode Condition
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
Power On
a
a
a
a
Power On
a
a
a
a
×
×
×
×
×
×
×
×
×
×
×
×
×
×
×
×
×
Freeze On
a
a
a
a
Freeze On
×
×
a*
×
×
×
×
×
×
×
×
×
×
×
×
×
×
×
×
×
×
MemRecall
a
a
a
a
MemRecall
×
×
×
×
a
a
a
a
a
a
a
a
a
a
a
a
×
×
×
a
×
×
×
×
×
a
a
a
×
×
×
×
a
×
a
a
a
a
a
×
a
a
×
×
×
×
a
a
a
×
×
×
×
×
×
a
a
a
×
×
a
×
×
Zoom Direct Focus Direct ZmFo Direct
a
a
a
a
a
a
a
a
a
×
a
×
×
a
a
a
a
a
×
a
a
Focus Auto
Basic Functions
30
×
×
×
×
×
×
×
×
×
×
×
×
×
×
Exposure Compensation Setting
BackLight On/Off
SpotAE On/Off
SpotAE Setting
WD On/Off
×
×
×
×
×
×
×
Gain Setting
Bright Setting
×
×
×
×
×
Shutter Setting
Iris Setting
Slow Shutter Auto/Manual
×
×
Bright
Exposure Compensation On/Off
×
×
×
×
Shutter Priority
Iris Priority
×
×
×
×
AE Full Auto
Initializing
AE Manual
Mode
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
Power On
×
×
×
×
a
×
×
×
×
×
×
×
×
×
×
×
×
×
×
×
Freeze On
×
×
×
a
Power On Freeze On MemRecall WB AUTO
Power Off
×
×
BGain Setting
Exposure
×
×
×
×
One Push WB
RGain Setting
×
×
Power Off Initializing
WB Mode Switchover
Mode
White Balance
a
×
×
×
×
×
×
×
×
×
×
×
×
×
×
×
MemRecall
×
×
×
a
Indoor
a
a
a
a
a
a
a
a
×
×
×
×
a
a
a
a
a
a
a
a
×
a
a
a
×
a
a
a
×
a
a
a
×
×
×
a
a
a
a
×
a
a
a
×
×
×
a
a
a
a
a
×
×
×
a
a
a
a
×
a
a
a
×
×
a
×
×
a
a
a
a
Iris Priority
×
×
a
a
Sodium
OnePush
Lamp AUTO
ShutterPri
a
Sodium
Lamp
AE Manual
×
×
×
a
Outdoor
AUTO
AE Full Auto
×
×
×
a
Outdoor
a
a
a
×
a
a
a
a
×
×
×
a
a
a
a
a
Bright
×
×
×
a
ATW
a
×
×
×
×
×
×
a
a
a
a
a
a
a
a
a
WD
a
a
×
a
Manual
Basic Functions
31
×
×
NR Level Setting
×
×
×
V-Phase Up/Down/Stop/Reset
×
×
×
V-Phase Direct
Initializing
Power Off
External Lock Mode
Mode
External Synchronization
×
×
×
×
Register Value Setting
×
×
Memory Save
Color Enhancement On/Off
×
×
×
×
MD Window Setting
ID Write
×
×
×
×
MD On/Off
×
×
Alarm Mode
MD Function Setting
×
×
×
×
Key Lock On/Off
Alarm On/Off
×
×
×
×
Mask On/Off
Mask Setting
×
×
×
×
Mute On/Off
×
×
Display On/Off
Title Setting
×
×
×
×
×
×
×
×
Auto ICR On/Off
Auto ICR Threshold Level Setting
Auto ICR Alarm On/Off
×
×
ICR On/Off
Image Stabilizer On/Off/Hold
×
×
×
×
Freeze On/Off
×
×
×
×
High Resolution Mode On/Off
LR_Reverse On/Off
Picture Effect Setting
×
×
×
×
WD Alarm On/Off
Initializing
Power Off
Aperture Setting
Mode
Others
a
a
a
Power On
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
Power On
a
a
a
Freeze On
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
×
×
a
×
×
×
a
×
a
×
×
Freeze On
a
a
a
MemRecall
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
×
×
a
×
×
×
×
×
a
×
×
MemRecall
Basic Functions
32
Command List
Command List
VISCA1)/RS-232C
Commands
This Manual outlines an RS-232 control protocol and
command list for certain Sony cameras from which
control software can be developed.
THIS CONTROL PROTOCOL AND COMMAND
LIST IS PROVIDED BY SONY ON AN “AS-IS
BASIS” WITHOUT WARRANTY OF ANY KIND.
SONY DOES NOT WARRANT ANY PARTICULAR
RESULT FROM THE USE OF THIS CONTROL
PROTOCOL AND COMMAND LIST AND
DISCLAIMS AND EXCLUDES ALL
WARRANTIES. EXPRESS OR IMPLIED, WITH
RESPECT TO THAT CONTROL PROTOCOL AND
COMMAND LIST, INCLUDING, BUT NOT
LIMITED TO, ANY OR ALL IMPLIED
WARRANTIES OF MERCHANTABILITY OR
FITNESS FOR A PARTICULAR PURPOSE. IN
FACT, SONY SPECIFICALLY ACKNOWLEDGES
THAT SOFTWARE DEVELOPED BASED ON THIS
CONTROL PROTOCOL AND COMMAND LIST
MAY CAUSE MALFUNCTION OR DAMAGE TO
HARDWARE AND SOFTWARE USED WITH IT
(INCLUDING SONY HARDWARE AND
SOFTWARE) AND SPECIFICALLY DISCLAIMS
ANY LIABILITY FOR ANY SUCH
MALFUNCTION OR DAMAGE. THIS CONTROL
PROTOCOL AND COMMAND LIST SHOULD BE
USED WITH CAUTION.
Overview of VISCA
In VISCA, the device outputting commands, for
example, a computer, is called the controller. The
device receiving the commands, an FCB camera is
called the peripheral device. In VISCA, up to seven
peripheral devices like the FCB camera can be
connected to one controller using communication
conforming to the RS-232C standard. The parameters
of RS-232C are as follows.
• Communication speed: 9.6 kbps/19.2 kbps/
38.4 kbps
• Data bits : 8
• Start bit : 1
• Stop bit : 1/2
• Non parity
Flow control using XON/XOFF and RTS/CTS, etc., is
not supported.
................................................................................................................................................................................................................................
1) VISCA is a protocol which controls consumer camcorders developed by Sony. “VISCA” is a trademark of Sony Corporation.
33
Command List
VISCA Communication
Specifications
assigned address 2 is 82H. In the command list, as the
header is 8X, input the address of the camera at X. The
header of the reply packet from the camera assigned
address 1 is 90H. The packet from the camera assigned
address 2 is A0H.
Some of the commands for setting cameras can be sent
to all devices at one time (broadcast). In the case of
broadcast, the header should be hexadecimal 88H.
When the terminator is FFH, it signifies the end of the
packet.
VISCA packet structure
The basic unit of VISCA communication is called a
packet. The first byte of the packet is called the header
and comprises the sender’s and receiver’s addresses.
For example, the header of the packet sent to the FCB
camera assigned address 1 from the controller (address
0) is hexadecimal 81H. The packet sent to the camera
Packet (3 to 16 bytes)
Header
Byte 1
1
Sender’s
address
Terminator
Message (1 to 14 bytes)
0
Byte 2
FF
Byte 3
Receiver’s address
Bit 7 Bit 6 Bit 5 Bit 4 Bit 3 Bit 2 Bit 1 Bit 0
(MSB)
(LSB)
1
1
1
1
1
1
1
1
Bit 7 Bit 6 Bit 5 Bit 4 Bit 3 Bit 2 Bit 1 Bit 0
(MSB)
(LSB)
Command and inquiry
● Command
Sends operational commands to the FCB camera.
● Inquiry
Used for inquiring about the current state of the
FCB camera.
Note
QQ1) = Command/Inquiry,
RR2) = category code
QQ = 01 (Command), 09 (Inquiry)
RR = 00 (Interface), 04 (camera 1), 06 (Pan/Tilter), 07 (camera 2)
Inquiry
1)
2)
Command Packet
8X QQ RR ... FF
X = 1 to 7: FCB camera address
34
Command List
Responses for commands and inquiries
Command execution cancel
● ACK message
Returned by the FCB camera when it receives a
command. No ACK message is returned for
inquiries.
To cancel a command which has already been sent,
send the Cancel command as the next command. To
cancel one of any two commands which have been
sent, use the cancel message.
● Completion message
Returned by the FCB camera when execution of
commands or inquiries is completed. In the case of
inquiry commands, it will contain reply data for the
inquiry after the 3rd byte of the packet. If the ACK
message is omitted, the socket number will contain
0.
Cancel Packet
Note
Cancel
8X 2Y FF
Y = socket number
X = 1 to 7: FCB camera address, Y = socket number
Reply Packet
Ack
X0 4Y FF
Completion (commands) X0 5Y FF
Completion (Inquiries)
X0 5Y ... FF
X = 9 to F: FCB camera address + 8
An error message will be returned for this command,
but this is not a fault. It indicates that the command has
been canceled.
Note
Y = socket number
Y = socket number
Y = socket number
● Error message
When a command or inquiry command could not be
executed or failed, an error message is returned
instead of the completion message.
Error Packet
Description
X0 6Y 01 FF
Message length error (>14 bytes)
X0 6Y 02 FF
Syntax Error
X0 6Y 03 FF
Command buffer full
X0 6Y 04 FF
Command cancelled
X0 6Y 05 FF
No socket (to be cancelled)
X0 6Y 41 FF
Command not executable
X = 9 to F: FCB camera address + 8, Y = socket number
Socket number
When command messages are sent to the FCB camera,
it is normal to send the next command message after
waiting for the completion message or error message
to return. However to deal with advanced uses, the
FCB camera has two buffers (memories) for
commands, so that up to two commands including the
commands currently being executed can be received.
When the FCB camera receives commands, it notifies
the sender which command buffer was used using the
socket number of the ACK message. As the
completion message or error message also has a socket
number, it indicates which command has ended. Even
when two command buffers are being used at any one
time, an FCB camera management command and some
inquiry messages can be executed.
The ACK message is not returned for these commands
and inquiries, and only the completion message of
socket number 0 is returned.
35
Command List
VISCA Device Setting
Command
Before starting control of the FCB camera, be sure to
send the Address command and the IF_Clear
command using the broadcast function.
For VISCA network administration
● Address
Sets an address of a peripheral device. Use when
initializing the network, and receiving the following
network change message.
● Network Change
Sent from the peripheral device to the controller
when a device is removed from or added to the
network. The address must be re-set when this
message is received.
Packet
Address
88 30 01 FF
Network Change
X0 38 FF
X = 9 to F: FCB camera address + 8
Note
Always broadcasted.
VISCA interface command
● IF_Clear
Clears the command buffers in the FCB camera and
cancels the command currently being executed.
Command Packet Reply Packet Note
IF_Clear
8X 01 00 01FF
X0 50 FF
IF_Clear (broadcast) 88 01 00 01 FF
88 01 00 01 FF
X = 1 to 7: FCB camera address (For inquiry packet)
X = 9 to F: FCB camera address +8 (For reply packet)
VISCA interface and inquiry
● CAM_VersionInq
Returns information on the VISCA interface.
Inquiry
Inquiry Packet Reply Packet
Description
CAM_VersionInq 8X 09 00 02 FF Y0 50 GG GG HH HH JJ JJ KK FF GGGG = Vender ID
(0020: Sony)
HHHH = Model ID
0452: FCB-EX995E
0453: FCB-EX995EP
0454: FCB-EX985E
0455: FCB-EX985EP
JJJJ = ROM revision
KK = Maximum socket #(02)
X = 1 to 7: FCB camera address (For inquiry packet)
X = 9 to F: FCB camera address +8 (For reply packet)
36
Command List
VISCA Command/ACK Protocol
Command
Command Message
Reply Message
Comments
General Command
81 01 04 38 02 FF
(Example)
90 41 FF (ACK)+90 51 FF
(Completion)
Returns ACK when a command has been accepted, and
Completion when a command has been executed.
81 01 04 38 FF
(Example)
90 60 02 FF (Syntax Error)
Accepted a command which is not supported or a command
lacking parameters.
81 01 04 38 02 FF
90 60 03 FF
(Example)
(Command Buffer Full)
There are two commands currently being executed, and the
command could not be accepted.
81 01 04 08 02 FF
(Example)
90 61 41 FF
(Command Not Executable)
90 42 FF
90 52 FF
Could not execute the command in the current mode.
90 62 41FF
Inquiry Command
81 09 04 38 FF
90 50 02 FF (Completion)
ACK is not returned for the inquiry command.
81 09 05 38 FF
(Example)
90 60 02 FF (Syntax Error)
Accepted an incompatible command.
Address Set
88 30 01 FF
88 30 02 FF
Returned the device address to +1.
IF_Clear(Broadcast)
88 01 00 01 FF
88 01 00 01 FF
Returned the same command.
IF_Clear (For x)
8x 01 00 01 FF
z0 50 FF (Completion)
ACK is not returned for this command.
Command Cancel
8x 2y FF
z0 6y 04 FF
(Command Canceled)
Returned when the command of the socket specified is canceled.
Completion for the command canceled is not returned.
z0 6y 05 FF (No Socket)
Returned when the command of the specified socket has already
been completed or when the socket number specified is wrong.
(Example)
37
Command List
VISCA Camera-Issued Messages
ACK/Completion Messages
ACK
Command Messages
Comments
z0 4y FF
Returned when the command is accepted.
(y:Socket No.)
Completion
z0 5y FF
(y:Socket No.)
Returned when the command has been executed.
z = Device address + 8
Error Messages
Command Messages
Comments
Syntax Error
z0 60 02 FF
Returned when the command format is different or when a command with illegal
command parameters is accepted.
Command Buffer Full
z0 60 03 FF
Indicates that two sockets are already being used (executing two commands) and the
command could not be accepted when received.
Command Canceled
z0 6y 04 FF
(y:Socket No.)
Returned when a command which is being executed in a socket specified by the
cancel command is canceled. The completion message for the command is not
returned.
No Socket
z0 6y 05 FF
(y:Socket No.)
Returned when no command is executed in a socket specified by the cancel
command, or when an invalid socket number is specified.
Command Not Executable
z0 6y 41 FF
(y:Socket No.)
Returned when a command cannot be executed due to current conditions. For
example, when commands controlling the focus manually are received during auto
focus.
Network Change Message
Network Change
Command Message
Comments
z0 38 FF
Issued when power is being routed.
38
Command List
FCB Camera Commands
New Command List (1/1)
Command Set
Command
Command Packet
Comments
CAM_IRCorrection
Standard
8x 01 04 11 00 FF
FOCUS IR compensation data switching
IR Light
8x 01 04 11 01 FF
Outdoor Auto
8x 01 04 35 06 FF
CAM_WB
Outdoor auto
Sodium Lamp Auto
8x 01 04 35 07 FF
Auto including sodium lamp source
Sodium Lamp
8x 01 04 35 08 FF
Sodium lamp source fixed mode
CAM_Gain
Gain Limit
8x 01 04 2C 0p FF
p: Gain Positionf 4 (6 dB) to F (28 dB)
CAM_WD
AutoOnOff
8x 01 04 3D 00 FF
WideD ON/OFF auto switching
On (RatioFix)
8x 01 04 3D 01 FF
WideD ON (fixed exposure ratio mode)
On (Dver Compati)
8x 01 04 3D 04 FF
Wide ON (Dver operation)
Refresh
8x 01 04 10 0D FF
WideD restart
Set Parameter
8x 01 04 2D 0p 0q 0r 0s 0t 0u
p: Screen display
00 00 FF
0: Combined image, 1: Long/short division, 2: Long-time,
3: Short-time
q: Detection sensitivity (0: L 1: M 2: H)
r: Blocked-up shadow correction level (0: L 1: M 2: H 3: S)
s: Blown-out highlight correction level (0: L 1: M 2: H)
tu: Exposure ratio of short exposure (x1 to x150)
CAM_WDAlarmReply
On
8x 01 04 3B 02 FF
WideD auto switching alarm ON/OFF
Off
8x 01 04 3B 03 FF
(Reply)
y0 07 04 3B 02 FF
y0 07 04 3B 03 FF
WideD ON t OFF
–
8x 01 04 53 0p FF
p: NR Setting (0: OFF, level 1 to 5)
CAM
On
8x 01 04 31 02 FF
Auto ICR switching alarm ON/OFF
_AutoICRAlarmReply
Off
8x 01 04 31 03 FF
(Reply)
y0 07 04 31 02 FF
ICR OFF t ON
y0 07 04 31 03 FF
ICR ON t OFF
On
8x 01 04 34 02 FF
Hand shake correction ON/OFF
Off
8x 01 04 34 03 FF
CAM_NR
CAM_Stabilizer
CAM_ExtLock
CAM_ColorEnhance
WideD OFF t ON
Hold
8x 01 04 34 00 FF
Hand shake correction hold
Internal Mode
8x 01 04 55 00 FF
Internal Sync
Line Lock Mode
8x 01 04 55 01 FF
V-Phase Adjustment
Frequency Lock Mode
8x 01 04 55 02 FF
External Sync
Parameter Set
8x 01 04 20 mm nn pp qq rr ss
mm: Threshold level
tt uu FF
nn: Hysteresis width
pp: Fixed color Y of high-intensity side
qq: Fixed color Cr of high-intensity side
rr: Fixed color Cb of high-intensity side
ss: Fixed color Y of low-intensity side
tt: Fixed color Cr of low-intensity side
uu: Fixed color Cb of low-intensity side
* Set 00h to 7Fh for each parameter.
On
8x 01 04 50 02 FF
Off
8x 01 04 50 03 FF
Color Enhancement ON/OFF
39
Command List
Command List (1/6)
Command Set
Command
Command Packet
Comments
AddressSet
Broadcast
88 30 01 FF
Address setting
IF_Clear
Broadcast
88 01 00 01 FF
I/F Clesr
CommandCancel
–
8x 2p FF
p: Socket No. (=1 or 2)
Power ON/OFF
CAM_Power
CAM_Zoom
CAM_DZoom
CAM_Focus
AF Sensitivity
CAM_AFMode
CAM_IRCorrection
On
8x 01 04 00 02 FF
Off
8x 01 04 00 03 FF
Stop
8x 01 04 07 00 FF
Tele(Standard)
8x 01 04 07 02 FF
Wide(Standard)
8x 01 04 07 03 FF
Tele(Variable)
8x 01 04 07 2p FF
Wide(Variable)
8x 01 04 07 3p FF
Direct
8x 01 04 47 0p 0q 0r 0s FF
pqrs: Zoom Position
On
8x 01 04 06 02 FF
Digital zoom ON/OFF
p=0 (Low) to 7 (High)
Off
8x 01 04 06 03 FF
Combine Mode
8x 01 04 36 00 FF
Optical/Digital Zoom Combined
Separate Mode
8x 01 04 36 01 FF
Optical/Digital Zoom Separate
Stop
8x 01 04 06 00 FF
Tele(Variable)
8x 01 04 06 2p FF
Wide(Variable)
8x 01 04 06 3p FF
x1/Max
8x 01 04 06 10 FF
x1/MAX Magnification Switchover
Direct
8x 01 04 46 00 00 0p 0q FF
pq: D-Zoom Position
Stop
8x 01 04 08 00 FF
Far(Standard)
8x 01 04 08 02 FF
Near(Standard)
8x 01 04 08 03 FF
p=0 (Low) to 7 (High)
Far(Variable)
8x 01 04 08 2p FF
Near(Variable)
8x 01 04 08 3p FF
p=0 (Low) to 7 (High)
Direct
8x 01 04 48 0p 0q 0r 0s FF
pqrs: Focus Position
Auto Focus
8x 01 04 38 02 FF
AF ON/OFF
Manual Focus
8x 01 04 38 03 FF
Auto/Manual
8x 01 04 38 10 FF
One Push Trigger
8x 01 04 18 01 FF
One Push AF Trigger
Infinity
8x 01 04 18 02 FF
Forced infinity
Near Limit
8x 01 04 28 0p 0q 0r 0s FF
pqrs: Focus Near Limit Position
Normal
8x 01 04 58 02 FF
AF Sensitivity High/Low
Low
8x 01 04 58 03 FF
Normal AF
8x 01 04 57 00 FF
Interval AF
8x 01 04 57 01 FF
Zoom Trigger AF
8x 01 04 57 02 FF
AF Movement Mode
Active/Interval Time
8x 01 04 27 0p 0q 0r 0s FF
pq: Movement Time, rs: Interval
Standard
8x 01 04 11 00 FF
FOCUS IR compensation data switching
IR Light
8x 01 04 11 01 FF
CAM_ZoomFocus
Direct
8x 01 04 47 0p 0q 0r 0s
pqrs: Zoom Position
0t 0u 0v 0w FF
tuvw: Focus Position
CAM_Initialize
Lens
8x 01 04 19 01 FF
Lens Initialization Start
Comp Scan
8x 01 04 19 02 FF
Correction of CCD pixel blemishes
40
Command List
Command List (2/6)
Command Set
CAM_WB
CAM_RGain
CAM_BGain
CAM_AE
CAM_SlowShutter
CAM_Shutter
CAM_Iris
CAM_Gain
CAM_Bright
CAM_ExpComp
Command
Command Packet
Comments
Auto
8x 01 04 35 00 FF
Normal Auto
Indoor
8x 01 04 35 01 FF
Indoor mode
Outdoor
8x 01 04 35 02 FF
Outdoor mode
One Push WB
8x 01 04 35 03 FF
One Push WB mode
ATW
8x 01 04 35 04 FF
Auto Tracing White Balance
Manual
8x 01 04 35 05 FF
Manual Control mode
One Push Trigger
8x 01 04 10 05 FF
One Push WB Trigger
Outdoor Auto
8x 01 04 35 06 FF
Outdoor auto
Sodium Lamp Auto
8x 01 04 35 07 FF
Auto including sodium lamp source
Sodium Lamp
8x 01 04 35 08 FF
Sodium lamp source fixed mode
Reset
8x 01 04 03 00 FF
Manual Control of R Gain
Up
8x 01 04 03 02 FF
Down
8x 01 04 03 03 FF
Direct
8x 01 04 43 00 00 0p 0q FF
pq: R Gain
Reset
8x 01 04 04 00 FF
Manual Control of B Gain
Up
8x 01 04 04 02 FF
Down
8x 01 04 04 03 FF
Direct
8x 01 04 44 00 00 0p 0q FF
pq: B Gain
Full Auto
8x 01 04 39 00 FF
Automatic Exposure mode
Manual
8x 01 04 39 03 FF
Manual Control mode
Shutter Priority
8x 01 04 39 0A FF
Shutter Priority Automatic Exposure mode
Iris Priority
8x 01 04 39 0B FF
Iris Priority Automatic Exposure mode
Bright
8x 01 04 39 0D FF
Bright Mode (Manual control)
Auto Slow Shutter ON/OFF
Auto
8x 01 04 5A 02 FF
Manual
8x 01 04 5A 03 FF
Reset
8x 01 04 0A 00 FF
Up
8x 01 04 0A 02 FF
Down
8x 01 04 0A 03 FF
Shutter Setting
Direct
8x 01 04 4A 00 00 0p 0q FF
pq: Shutter Position
Reset
8x 01 04 0B 00 FF
Iris Setting
Up
8x 01 04 0B 02 FF
Down
8x 01 04 0B 03 FF
Direct
8x 01 04 4B 00 00 0p 0q FF
pq: Iris Position
Reset
8x 01 04 0C 00 FF
Gain Setting
Up
8x 01 04 0C 02 FF
Down
8x 01 04 0C 03 FF
Direct
8x 01 04 4C 00 00 0p 0q FF
pq: Gain Position
Gain Limit
8x 01 04 2C 0p FF
p: Gain Position
Reset
8x 01 04 0D 00 FF
Bright Setting
Up
8x 01 04 0D 02 FF
Down
8x 01 04 0D 03 FF
Direct
8x 01 04 4D 00 00 0p 0q FF
pq: Bright Position
On
8x 01 04 3E 02 FF
Exposure Compensation ON/OFF
Off
8x 01 04 3E 03 FF
Reset
8x 01 04 0E 00 FF
Up
8x 01 04 0E 02 FF
Down
8x 01 04 0E 03 FF
Direct
8x 01 04 4E 00 00 0p 0q FF
Exposure Compensation Amount Setting
pq: ExpComp Position
41
Command List
Command List (3/6)
Command Set
Command
Command Packet
Comments
CAM_Backlight
On
8x 01 04 33 02 FF
Back Light Compensation ON/OFF
Off
8x 01 04 33 03 FF
On
8x 01 04 59 02 FF
Off
8x 01 04 59 03 FF
CAM_SpotAE
CAM_AE_Response
CAM_WD
Spot Automatic Exposure Setting
Position
8x 01 04 29 0p 0q 0r 0s FF
pq: X (0 to F), rs: Y (0 to F)
DIRECT
8x 01 04 5D pp FF
Automatic Exposure Response Setting (01 to 30)
Wide-D ON/OFF
On
8x 01 04 3D 02 FF
Off
8x 01 04 3D 03 FF
AutoOnOff
8x 01 04 3D 00 FF
Wide dynamic ON/OF auto switching
On(RatioFix)
8x 01 04 3D 01 FF
Wide dynamic ON (Fixed exposure ratio mode)
On(Dver Compati)
8x 01 04 3D 04 FF
Wide dynamic ON (Dver operation)
Refresh
8x 01 04 10 0D FF
Wide dynamic restart
Set Parameter
8x 01 04 2D 0p 0q 0r 0s 0t 0u
p: Screen display
00 00 FF
0: Combined image, 1: Long/short division, 2: Long-time,
3: Short-time
q: Detection sensitivity (0: L 1: M 2: H)
r: Blocked-up shadow correction level (0: L 1: M 2: H 3: S)
s: Blown-out highlight correction level (0: L 1: M 2: H)
tu: Exposure ratio of short exposure (x1 to x150)
CAM_WDAlarmReply
CAM_Aperture
On
8x 01 04 3B 02 FF
Wide dynamic auto switching alarm ON/OFF
Off
8x 01 04 3B 03 FF
(Reply)
y0 07 04 3B 02 FF
Wide dynamic OFF t ON
y0 07 04 3B 03 FF
Wide dynamic ON t OFF
Reset
8x 01 04 02 00 FF
Aperture Control
Up
8x 01 04 02 02 FF
Down
8x 01 04 02 03 FF
Direct
8x 01 04 42 00 00 0p 0q FF
pq: Aperture Gain
CAM_HR
On
8x 01 04 52 02 FF
High-Resolusion Mode ON/OFF
Off
8x 01 04 52 03 FF
CAM_NR
–
8x 01 04 53 0p FF
p: NR Setting (0: OFF, level 1 to 5)
Mirror Image ON/OFF
CAM_LR_Reverse
CAM_Freeze
CAM_PictureEffect
CAM_PictureFlip
CAM_ICR
CAM_AutoICR
On
8x 01 04 61 02 FF
Off
8x 01 04 61 03 FF
On
8x 01 04 62 02 FF
Off
8x 01 04 62 03 FF
Off
8x 01 04 63 00 FF
Neg.Art
8x 01 04 63 02 FF
B&W
8x 01 04 63 04 FF
On
8x 01 04 66 02 FF
Off
8x 01 04 66 03 FF
On
8x 01 04 01 02 FF
Off
8x 01 04 01 03 FF
On
8x 01 04 51 02 FF
Off
8x 01 04 51 03 FF
Threshold
8x 01 04 21 00 00 0p 0q FF
Still Image ON/OFF
Picture Effect Setting
Picture flip ON/OFF
Infrared Mode ON/OFF
Auto dark-field mode On/Off
pq: ICR ON t OFF threshold level
42
Command List
Command List (4/6)
Command Set
Command
Command Packet
Comments
CAM
On
8x 01 04 31 02 FF
Auto ICR switching Alarm ON/OFF
_AutoICRAlarmReply
Off
8x 01 04 31 03 FF
(Reply)
y0 07 04 31 02 FF
ICR OFF t ON
CAM_Stabilizer
CAM_Memory
CAM_Display
y0 07 04 31 03 FF
ICR ON t OFF
On
8x 01 04 34 02 FF
Hand shake correction ON/OFF
Off
8x 01 04 34 03 FF
Hold
8x 01 04 34 00 FF
Hand shake correction hold
p: Memory Number (=0 to 5)
Reset
8x 01 04 3F 00 0p FF
Set
8x 01 04 3F 01 0p FF
Recall
8x 01 04 3F 02 0p FF
On
8x 01 04 15 02 FF
Display ON/OFF
(8x 01 06 06 02 FF)
Off
8x 01 04 15 03 FF
(8x 01 06 06 03 FF)
On/Off
8x 01 04 15 10 FF
(8x 01 06 06 10 FF)
CAM_Title
CAM_MultiLineTitle
CAM_Mute
Title Set1
8x 01 04 73 00 mm nn pp qq 00 00
00 00 00 00 FF
L: Line Number, nn: H-Position
pp: Color, qq: Blink
Title Set2
8x 01 04 73 01 mm nn pp qq rr ss
tt uu vv ww FF
mnpqrstuvw: Display character setting
(1st to 10th character)
Title Set3
8x 01 04 73 02 mm nn pp qq rr ss
mnpqrstuvw: Display character setting
tt uu vv ww FF
(11th to 20th character)
Title Clear
8x 01 04 74 00 FF
Clear title setting
On
8x 01 04 74 02 FF
Title display ON/OFF
Off
8x 01 04 74 03 FF
Title Set1
8x 01 04 73 1L 00 nn pp
L: Line Number, nn: H-position
qq rr 00 00 00 00 00 FF
pp: Color, qq: Blink rr: Opening Title
Title Set2
8x 01 04 73 2L mm nn pp
qq rr ss tt uu vv ww FF
L: Line Number,
mnpqrstuvw: Setting of characters (1 to 10)
Title Set3
8x 01 04 73 3L mm nn pp
qq rr ss tt uu vv ww FF
L: Line Number,
mnpqrstuvw: Setting of characters (11 to 20)
Title Clear
8x 01 04 74 1p FF
Title Setting clear (p: 0 to a, f= all lines)
On
8x 01 04 74 2p FF
Title display On/Off (0 to a, f= all lines)
Off
8x 01 04 74 3p FF
On
8x 01 04 75 02 FF
Off
8x 01 04 75 03 FF
On/Off
8x 01 04 75 10 FF
Muting ON/OFF
43
Command List
Command List (5/6)
Command Set
Command
Command Packet
Comments
CAM_PrivacyZone
SetMask
8x 01 04 76 mm nn
0r 0r 0s 0s FF
mm: Mask Settings
nn 00: Modify, 01: New
rr: W, ss:H
Display
8x 01 04 77 pp pp pp pp FF
Mask Display ON/OFF
pp pp pp pp: Mask Settings (0:OFF, 1:ON)
SetMaskColor
8x 01 04 78 pp pp pp pp
qq rr FF
pp pp pp pp: Mask Color Settings
qq: Color Setting when 0 is selected
rr: Color Setting when 1 is selected
SetPanTiltAngle
SetPTZMask
CAM_KeyLock
8x 01 04 79 0p 0p 0p
Pan/Tilt Angle Settings
0q 0q 0q FF
ppp: Pan
qqq: Tilt
8x 01 04 7B mm 0p 0p 0p
Pan/Tilt/Zoom Settings for Mask
0q 0q 0q 0r 0r 0r 0r FF
ppp: Pan, qqq: Tilt, rrrr: Zoom
Non_InterlockMask
8x 01 04 6F mm
0p 0p 0q 0q 0r 0r 0s 0s FF
mm: Non_Interlock Mask Settings
pp: X, q: Y, rr: W, ss: H
GridOn
8x 01 04 7C 02 FF
Grid Display ON/OFF
GridOff
8x 01 04 7C 03 FF
Grid/Center Line Display Off
CenterLineOn
8x 01 04 7C 04 FF
Center Line Display On
Off
8x 01 04 17 00 FF
Camera Control Enable/Disable
On
8x 01 04 17 02 FF
CAM_IDWrite
–
8x 01 04 22 0p 0q 0r 0s FF
CAM_MemSave
Write
8x 01 04 23 0m 0p 0q 0r 0s FF
pqrs: Camera ID (=0000 to FFFF)
m: Address (=0 to 7)
pqrs: Data (0000 to FFFF)
CAM_ExtLock
CAM_VPhase
CAM_Alarm
Internal Mode
8x 01 04 55 00 FF
Internal Sync
Line Lock Mode
8x 01 04 55 01 FF
V-Phase Adjustment
Frequency Lock Mode
8x 01 04 55 02 FF
External Sync
Stop
8x 01 04 05 00 FF
–
Up
8x 01 04 05 02 FF
Down
8x 01 04 05 03 FF
Up (Step)
8x 01 04 05 2p FF
Down (Step)
8x 01 04 05 3p FF
Reset
8x 01 04 05 40 FF
Restore Factory Settings
Direct
8x 01 04 45 0p 0q 0r 0s FF
pqrs: V-Phase (0000 to)
(NTSC: 0000 to 20Chex, PAL: 0000 to 270hex)
Alarm ON/OFF
On
8x 01 04 6B 02 FF
Off
8x 01 04 6B 03 FF
SetMode
8x 01 04 6C pp FF
p=step (1-7)
pp: Mode setting
00 Focus change detection
(reference value is not updated)
01 Focus change detection (reference value is updated)
02 AE change detection (reference value is not updated)
03 AE change detection (reference value is updated)
:
0C Day/Night judgement
SetDayNighLevel
8x 01 04 6D 0p 0p 0p 0q 0q 0q FF
ppp: Day judgement level setting
qqq: Night judgement level setting
Alarm(Reply)
y0 07 04 6B 01 FF
Detection level “ Low” t “High”
y0 07 04 6B 00 FF
Detection level “ High” t “Low”
44
Command List
Command List (6/6)
Command Set
CAM_MD
Command
Command Packet
Comments
Motion Detection On/Off
On
8x 01 04 1B 02 FF
Off
8x 01 04 1B 03 FF
Function Set
8x 01 04 1C 0m 0n 0p 0q 0r 0s FF
m: Display mode
n: Detection Frame Set (0 to F)
pq: Threshold Level (00 to FF)
rs: Interval Time set (00 to FF)
Window Set
8x 01 04 1D 0m 0p 0q 0r 0s FF
m: Select Detection Frame (0, 1, 2, 3)
p: Start Horizontal Position (00 to 0B)
q: Start Vertical Position (00 to 07)
r: Stop Horizontal Position (01 to 0C)
s: Stop Vertical Position (01 to 08)
Alarm (Reply)
y0 07 04 1B 0p FF
p: Detection Frame Number
CAM_Continuous
On
8x 01 04 69 02 FF
ZoomPosition data Continuous Output On/Off
ZoomPosReply
Off
8x 01 04 69 03 FF
(Reply)
y0 07 04 69 0p 0p 0q 0q 0q 0q FF
pp: D-Zoom Position
* 00: When Zoom Mode is Combine
qqqq: Zoom Position
CAM_
ReplyIntervalTimeSet
–
8x 01 04 6A 00 00 0p 0p FF
pp: Interval Time [Vertical timing]
CAM_RegisterValue
–
8x 01 04 24 mm 0p 0p FF
mm: Register No. (=00-7F)
pp: Register Value (=00-7F)
CAM_ColorEnhance
Parameter Set
8x 01 04 20 mm nn
mm: Threshold level
pp qq rr ss tt uu FF
nn: Hysteresis width
pp: Fixed color Y of high-intensity side
qq: Fixed color Cr of high-intensity side
rr: Fixed color Cb of high-intensity side
ss: Fixed color Y of low-intensity side
tt: Fixed color Cr of low-intensity side
uu: Fixed color Cb of low-intensity side
* Set 00h to 7Fh for each parameter.
On
8x 01 04 50 02 FF
Off
8x 01 04 50 03 FF
Color Enhancement ON/OFF
45
Command List
New Query Command List (1/1)
Inquiry Command
Command Packet
CAM_IRCorrectionInq
8x 09 04 11 FF
CAM_WBModeInq
8x 09 04 35 FF
Inquiry Packet
Comments
y0 50 00 FF
Standard
y0 50 01 FF
IR Light
y0 50 06 FF
Outdoor Auto
y0 50 07 FF
Sodium Lamp Auto
y0 50 08 FF
Sodium Lamp
CAM_GainLimitInq
8x 09 04 2C FF
y0 50 0q FF
p: Gain Limit
CAM_WDModeInq
8x 09 04 3D FF
y0 50 01 FF
On (RatioFix)
y0 50 04 FF
On (Dver operation)
CAM_WDParameterInq
8x 09 04 2D FF
y0 50 00 0p 0q 0r 0s 0t 0u 00 00 FF
p: Screen display
q: Detection sensitivity
r: Blocked-up shadow correction level
s: Blown-out highlight correction level
tu: Exposure ratio of short exposure
CAM_WDAlarmReplyInq
8x 09 04 3B FF
CAM_NRInq
8x 09 04 53 FF
CAM_StabilizerModeInq
8x 09 04 34 FF
CAM_ExtLockInq
CAM_ColorEnhanceInq
8x 09 04 55 FF
8x 09 04 20 FF
y0 50 02 FF
On
y0 50 03 FF
Off
y0 50 0p FF
p: NR level
y0 50 02 FF
On
y0 50 03 FF
Off
y0 50 00 FF
Hold
y0 50 00 FF
Internal Sync
y0 50 01 FF
V-Phase Adjustment
y0 50 02 FF
External Sync
y0 50 mm nn pp qq rr ss tt uu FF
mm: Threshold level
nn: Hysteresis width
pp: Fixed color Y of high-intensity side
qq: Fixed color Cr of high-intensity side
rr: Fixed color Cb of high-intensity side
ss: Fixed color Y of low-intensity side
tt: Fixed color Cr of low-intensity side
uu: Fixed color Cb of low-intensity side
8x 09 04 50 FF
CAM_TempInq
8x 09 04 68 FF
y0 50 02 FF
On
y0 50 03 FF
Off
y0 50 00 00 0p 0p FF
pq: Temperature * Lens temperature
46
Command List
Inquiry Command List (1/4)
Inquiry Command
Command Packet
CAM_PowerInq
8x 09 04 00 FF
Inquiry Packet
Comments
y0 50 02 FF
On
y0 50 03 FF
Off
CAM_ZoomPosInq
8x 09 04 47 FF
y0 50 0p 0q 0r 0s FF
pqrs: Zoom Position
CAM_DZoomModeInq
8x 09 04 06 FF
y0 50 02 FF
D-Zoom On
y0 50 03 FF
D-Zoom Off
y0 50 00 FF
Combine Mode
y0 50 01 FF
Separate Mode
CAM_DZoomC/SModeInq
8x 09 04 36 FF
CAM_DZoomPosInq
8x 09 04 46 FF
y0 50 00 00 0p 0q FF
pq: D-Zoom Position
CAM_FocusModeInq
8x 09 04 38 FF
y0 50 02 FF
Auto Focus
y0 50 03 FF
Manual Focus
CAM_FocusPosInq
8x 09 04 48 FF
y0 50 0p 0q 0r 0s FF
pqrs: Focus Position
CAM_FocusNearLimitInq
8x 09 04 28 FF
y0 50 0p 0q 0r 0s FF
pqrs: Focus Near Limit Position
CAM_AFSensitivityInq
8x 09 04 58 FF
y0 50 02 FF
AF Sensitivity Normal
y0 50 03 FF
AF Sensitivity Low
y0 50 00 FF
Normal AF
y0 50 01 FF
Interval AF
CAM_AFModeInq
8x 09 04 57 FF
y0 50 02 FF
Zoom Trigger AF
CAM_AFTimeSettingInq
8x 09 04 27 FF
y0 50 0p 0q 0r 0s FF
pq: Movement Time, rs: Interval
CAM_IRCorrectionInq
8x 09 04 11 FF
y0 50 00 FF
Standard
CAM_WBModeInq
8x 09 04 35 FF
CAM_RGainInq
8x 09 04 43 FF
y0 50 01 FF
IR Light
y0 50 00 FF
Auto
y0 50 01 FF
In Door
y0 50 02 FF
Out Door
y0 50 03 FF
One Push WB
y0 50 04 FF
ATW
y0 50 05 FF
Manual
y0 50 06 FF
Outdoor Auto
y0 50 07 FF
Sodium Lamp Auto
y0 50 08 FF
Sodium Lamp
y0 50 00 00 0p 0q FF
pq: R Gain
CAM_BGainInq
8x 09 04 44 FF
y0 50 00 00 0p 0q FF
pq: B Gain
CAM_AEModeInq
8x 09 04 39 FF
y0 50 00 FF
Full Auto
y0 50 03 FF
Manual
y0 50 0A FF
Shutter Priority
y0 50 0B FF
Iris Priority
y0 50 0D FF
Bright
y0 50 02 FF
Auto
CAM_SlowShutterModeInq
8x 09 04 5A FF
CAM_ShutterPosInq
8x 09 04 4A FF
y0 50 03 FF
Manual
y0 50 00 00 0p 0q FF
pq: Shutter Position
CAM_IrisPosInq
8x 09 04 4B FF
y0 50 00 00 0p 0q FF
pq: Iris Position
CAM_GainPosInq
8x 09 04 4C FF
y0 50 00 00 0p 0q FF
pq: Gain Position
CAM_GainLimitInq
8x 09 04 2C FF
y0 50 0q FF
p: Gain Limit
CAM_BrightPosInq
8x 09 04 4D FF
y0 50 00 00 0p 0q FF
pq: Bright Position
CAM_ExpCompModeInq
8x 09 04 3E FF
y0 50 02 FF
On
y0 50 03 FF
Off
CAM_ExpCompPosInq
8x 09 04 4E FF
y0 50 00 00 0p 0q FF
pq: ExpComp Position
CAM_BacklightModeInq
8x 09 04 33 FF
y0 50 02 FF
On
y0 50 03 FF
Off
47
Command List
Inquiry Command List (2/4)
Inquiry Command
Command Packet
CAM_SpotAEModeInq
8x 09 04 59 FF
Inquiry Packet
Comments
y0 50 02 FF
On
y0 50 03 FF
Off
CAM_SpotAEPosInq
8x 09 04 29 FF
y0 50 0p 0q 0r 0s FF
pq: X position, rs: Y position
CAM_AE_ResponseInq
8x 09 04 5D FF
y0 50 pp FF
pp: 01 to 20 (hex)
CAM_WDModeInq
8x 09 04 3D FF
y0 50 02 FF
On Wide-D
CAM_WDParameterInq
8x 09 04 2D FF
y0 50 03 FF
Off
y0 50 00 FF
AutoOnOff
y0 50 01 FF
On (RatioFix)
y0 50 04 FF
On (Dver operation)
y0 50 0p 0q 0r 0s 0t 0u 00 00 FF
p: Screen display
q: Detection sensitivity
r: Blocked-up shadow correction level
s: Blown-out highlight correction level
tu: Exposure ratio of short exposure
CAM_WDAlarmReplyInq
8x 09 04 3B FF
y0 50 02 FF
On
y0 50 03 FF
Off
CAM_ApertureInq
8x 09 04 42 FF
y0 50 00 00 0p 0q FF
pq: Aperture Gain
CAM_HRModeInq
8x 09 04 52 FF
y0 50 02 FF
On Hi-Resolution
y0 50 03 FF
Off
CAM_NRInq
8x 09 04 53 FF
y0 50 0p FF
p: NR level
CAM_LR_ReverseModeInq
8x 09 04 61 FF
y0 50 02 FF
On
y0 50 03 FF
Off
CAM_FreezeModeInq
8x 09 04 62 FF
y0 50 02 FF
On
y0 50 03 FF
Off
CAM_PictureEffectModeInq
8x 09 04 63 FF
y0 50 00 FF
Off
y0 50 02 FF
Neg.Art
y0 50 04 FF
B&W
y0 50 02 FF
On
y0 50 03 FF
Off
y0 50 02 FF
On
CAM_PictureFlipModeInq
8x 09 04 66 FF
CAM_ICRModeInq
8x 09 04 01 FF
y0 50 03 FF
Off
CAM_AutoICRModeInq
8x 09 04 51 FF
y0 50 02 FF
On
y0 50 03 FF
Off
CAM_AutoICRThresholdInq
8x 09 04 21 FF
y0 50 00 00 0p 0q FF
pq: ICR ON t OFF Threshold Level
CAM_AutoICRAlarmReplyInq
8x 09 04 31 FF
y0 50 02 FF
On
y0 50 03 FF
Off
CAM_StabilizerModeInq
8x 09 04 34 FF
y0 50 02 FF
On
y0 50 03 FF
Off
y0 50 00 FF
Hold
CAM_DisplayModeInq
8x 09 04 15 FF
y0 50 02 FF
On
(8x 09 06 06 FF)
y0 50 03 FF
Off
CAM_MuteModeInq
8x 09 04 75 FF
y0 50 02 FF
On
y0 50 03 FF
Off
CAM_PrivacyDisplayInq
8x 09 04 77 FF
y0 50 pp pp pp pp FF
pp pp pp pp: Mask Display (0:OFF, 1:ON)
48
Command List
Inquiry Command List (3/4)
Inquiry Command
Command Packet
Inquiry Packet
Comments
CAM_PrivacyPanTiltInq
8x 09 04 79 FF
y0 50 0p 0p 0p 0q 0q 0q FF
ppp: Pan
qqq: Tilt
CAM_PrivacyPTZInq
8x 09 04 7B mm FF
y0 50 0p 0p 0p 0q 0q 0q 0r 0r
0r 0r FF
mm: Mask Settings
ppp: Pan
qqq: Tilt
rrr: Zoom
CAM_PrivacyMonitorInq
8x 09 04 6F FF
y0 50 pp pp pp pp FF
pp pp pp pp: Mask is displayed now.
CAM_KeyLockInq
8x 09 04 17 FF
y0 50 00 FF
Off
y0 50 02 FF
On
pqrs: Camera ID
CAM_IDInq
8x 09 04 22 FF
y0 50 0p 0q 0r 0s FF
CAM_MemSaveInq
8x 09 04 23 0X FF
y0 50 0p 0p 0q 0q FF
X: 00 to 07 (Address)
ppqq: 0x0000 to 0xFFFF (Data)
CAM_ExtLockInq
8x 09 04 55 FF
y0 50 00 FF
Internal Sync
y0 50 01 FF
V-Phase Adjustment
y0 50 02 FF
External Sync
CAM_VPhasePosInq
8x 09 04 45 FF
y0 50 0p 0q 0r 0s FF
pqrs: V-Phase Position
CAM_VersionInq
8x 09 00 02 FF
y0 50 00 20
mnpq: Model Code (04xx)
mn pq rs tu vw FF
rstu: ROM version
vw: Socket Number (=02)
CAM_AlarmInq
8x 09 04 6B FF
y0 50 02 FF
On
y0 50 03 FF
Off
CAM_AlarmModeInq
8x 09 04 6C FF
y0 50 pp FF
pp: Alarm Mode
CAM_AlarmDayNightLevelInq
8x 09 04 6D FF
y0 50 0p 0p 0p
ppp: Day judgement level setting
0q 0q 0q 0r 0r 0r FF
qqq: Night judgement level setting
y0 50 01 FF
Detection level “High”
y0 50 00 FF
Detection level “Low”
y0 50 02 FF
On
rrr: Current Automatic Exposure level setting
CAM_AlarmDetectLevelInq
8x 09 04 6E FF
CAM_MDModeInq
8x 09 04 1B FF
y0 50 03 FF
Off
CAM_MDFunctionInq
8x 09 04 1C FF
y0 50 0m 0n 0p 0q FF
m: Display mode
n: Detection Frame Set (0 to F)
pq: Threshold Level (0 to FF)
rs: Interval Time set (0 to FF)
CAM_MDWindowInq
8x 09 04 1D 0m FF
y0 50 0p 0q 0r 0s FF
m: Select Detection Frame (0, 1, 2, 3)
p: Start Horizontal Position (00 to 0B)
q: Start Vertical Position (00 to 07)
r: Stop Horizontal Position (01 to 0C)
s: Stop Vertical Position (01 to 08)
CAM_ContinuousZoomPos
8x 09 04 69 FF
ReplyModeInq
y0 50 02 FF
On
y0 50 03 FF
Off
CAM_ReplyIntervalTimeInq
8x 09 04 6A FF
y0 50 00 00 0p 0p FF
pp: Interval Time
CAM_RegisterValueInq
8x 09 04 24 mm FF
y0 50 0p 0p ff
mm: Register No. (00 to 7F)
pp: Register Value (00 to FF)
49
Command List
Inquiry Command List (4/4)
Inquiry Command
Command Packet
Inquiry Packet
Comments
CAM_ColorEnhanceInq
8x 09 04 20 FF
y0 50 mm nn pp qq rr ss tt uu FF
mm: Threshold level
nn: Hysteresis width
pp: Fixed color Y of high-intensity side
qq: Fixed color Cr of high-intensity side
rr: Fixed color Cb of high-intensity side
ss: Fixed color Y of low-intensity side
tt: Fixed color Cr of low-intensity side
uu: Fixed color Cb of low-intensity side
8x 09 04 50 FF
CAM_TempInq
8x 09 04 68 FF
y0 50 02 FF
On
y0 50 03 FF
Off
y0 50 00 00 0p 0p FF
pq: Temperature * Lens temperature
50
Command List
Block Inquiry Command List
Lens Control System Inquiry Commands .............. Command Packet 8x 09 7E 7E 00 FF
Byte
Bit
Comments
Bit
Comments
7
7
0
7
0
6
6
0
6
0
5
0
5
0
4
0
4
0
3
0
2
0
1
0
Bit
5
0
Comments
Destination Address
4
6
3
2
1
Byte
2
Source Address
1
1
2
0 Completion Message (50h)
0
0
7
0
1
6
0
6
0
5
0
5
4
1
4
0
3
0
2
0
2
1
0
1
0
0
0
7
0
7
7
0
DZoomMode 0: Combine
1: Separate
4
0: Normal 1: Interval
3
2: Zoom Trigger
2
AF Sensitivity 0: Slow
1: Normal
0
1
Digital Zoom 1:On 0:Off
Focus Mode 0:Manual 1:Auto
3
13
Focus Near Limit (L)
6
0
6
0
0
5
0
5
0
7
0
0
6
0
5
0
4
0
3
8
4
3
2
Zoom Position (HH)
1
Focus Position (HH)
7
0
7
0
6
0
6
0
5
0
5
0
4
0
4
0
3
2
1
14
4
0
3
Low Contrast Detection 1: Yes
0: No
2
Camera Memory Recall
1: Executing 0: Stopped
1
Focus Command 1: Executing
0: Stopped
0
Zoom Command 1: Executing
0: Stopped
7
1 Terminator (FFh)
0
0
9
3
2
Zoom Position (HL)
1
Focus Position (HL)
0
0
6
1
5
1
4
1
7
0
7
0
6
0
6
0
3
1
5
0
5
0
2
1
4
0
4
0
1
1
0
1
3
2
1
10
3
2
Zoom Position (LH)
1
Focus Position (LH)
7
0
7
0
6
0
6
0
5
0
5
0
4
0
4
0
3
2
1
0
15
0
0
5
0
7
5
1
4
Focus Near Limit (H)
6
2
3
12
0
0
7
3
Byte
Zoom Position (LL)
11
3
2
1
Focus Position (LL)
0
51
Command List
Camera Control System Inquiry Commands ......... Command Packet 8x 09 7E 7E 01 FF
Byte
Bit
Comments
Byte
7
6
5
0
4
1
0
6
0
6
0
5
0
5
0
4
0
4
0
12
3
1
Byte
3
2
WB Mode
1
Gain Position
7
7
0
7
0
1
6
0
6
0
0
5
0
0
4
0 Completion Message (50h)
0
5
0
5
4
1
4
3
0
3
2
0
2
1
0
1
0
0
0
7
0
7
0
7
0
6
0
6
0
6
0
5
0
5
0
5
0
4
0
4
4
0
7
8
3
3
2
2
R Gain (H)
13
3
2
Aperture Gain
Bright Position
1
0
14
Exposure Mode
3
2
1
1
0
Exposure Comp. Position
0
0
7
0
7
6
0
6
0
6
1
5
0
5
High-Resolution 1: On 0: Off
5
1
0
4
Wide-D (1: Other than Off,
0: Off)
4
1
3
1
7
4
9
3
15
1 Terminator (FFh)
3
Spot AE 1: On 0: Off
2
1
2
Back Light 1:On 0:Off
1
1
0
1
Exposure Comp. 1:On 0:Off
0
1
7
0
0
Slow Shutter 1:Auto 0:Manual
6
0
7
0
5
0
6
0
0
5
0
2
1
4
R Gain (L)
3
2
1
10
B Gain (H)
4
3
2
Shutter Position
1
0
7
0
0
6
0
7
0
0
6
0
0
5
0
5
5
Comments
7
2
Source Address
0
4
Bit
0
0
1
3
Comments
7
0
6
2
6
3
2
1
Destination Address
Bit
4
3
2
1
0
11
B Gain (L)
4
3
2
Iris Position
1
0
52
Command List
Other Inquiry Commands ........................................ Command Packet 8x 09 7E 7E 02 FF
Byte
Bit
Bit
Comments
Bit
Comments
7
7
0
7
0
6
6
0
6
0
5
0
5
4
0
3
0
2
0
1
0
0
0
5
0
Comments
Byte
Destination Address
4
6
3
2
1
Source Address
0
7
1
2
0
12
Memory 1: Provided 0: Not
provided
3
Clock 1: Provided 0: Not
provided
2
5
0
5
0
4
1
4
0
3
0
3
0
2
0
2
0
1
0
1
0
0
0
0
0
7
0
7
0
6
0
6
0
5
0
5
0
3
4
0
4
0
2
3
Auto ICR Alarm (1: On, 0: Off)
3
2
Auto ICR 1: On 0: Off
2
1
Key Lock 1: On 0: Off
1
0
Power 1:On 0:Off
0
7
8
0
Stabilizer (1: On, 0: Off)
0
6
0
5
0
4
0
ICR 1: On 0: Off
3
Freeze 1:On 0:Off
3
2
LR Reverse 1:On 0:Off
2
9
1
0
1
0
0
0
7
0
7
6
0
0: Unlock)
13
4
External Lock Mode 1: Line
Lock 0: Internal
V-Phase (H)
0
7
0
6
0
5
14
4
3
2
V-Phase (L)
0
1 Terminator (FFh)
1
5
1
6
0
4
1
3
1
2
1
1
1
0
1
Mute 1: On 0: Off
4
0
3
Title Display 1: On 0: Off
3
2
Display 1: On 0: Off
2
Camera ID (LH)
1
0
1
0
0
0
7
0
7
0
6
0
6
0
5
0
5
0
4
0
4
0
3
0
0
0
External Lock status (1: Lock,
0
4
15
3
2
Picture Effect Mode
0
6
0
1
5
7
5
2
System 1:PAL 0:NTSC
6
Camera ID (HL)
Privacy Zone 1: On 0: Off
11
0
1
5
10
Stabilizer (1: Provided, 0: Not
provided)
7
Camera ID (HH)
0
4
1
1
7
ICR 1: Provided 0: Not
provided
6
5
5
0
0: Not provided
1
6
4
7
External Lock 1: Provided
4
6
7
3
0 Completion Message (50h)
Byte
1
Camera ID (LL)
0
53
Command List
Enlargement Function1 Query Command ............. Command Packet 8x 09 7E 7E 03 FF
Byte
Bit
Comments
Byte
7
6
0
0
5
0
4
4
0
4
0
6
3
3
2
2
Source Address
3
AF Interval Time (H)
0
0 Completion Message (50h)
7
0
1
6
0
5
0
5
0
4
1
4
0
3
0
3
2
0
2
1
0
1
0
0
0
7
0
7
0
6
0
6
0
5
0
5
0
4
0
4
0
7
8
3
3
2
2
Digital Zoom Position (H)
1
1
0
0
6
0
6
0
5
0
5
0
4
0
4
0
9
3
3
2
2
Digital Zoom Position (L)
7
6
0
6
0
5
0
5
0
4
0
4
0
3
3
0
2
2
MD (1: On, 0: Off)
1
1
Alarm (1: On, 0: Off)
0
0
Picture flip (1: On, 0: Off)
5
0
4
0
0
5
0
4
3
AE Response
7
0
6
0
5
0
4
0
3
0
NR Level
0
7
0
6
0
5
0
4
0
3
0
0
6
1
14
7
6
0
2
0
10
7
0
SpotAE Position (Y)
1
Picture flip (1: Provided,
0: Not provided)
1
13
0
0
Alarm (1: Provided, 0: Not
2
SpotAE Position (X)
7
7
1
0
12
0
AF Activation Time (H)
Advanced Privacy
(1: Provided, 0: Not provided)
provided)
AF Interval Time (L)
7
0
2
1
0
5
11
6
1
4
0
0
7
3
Comments
7
Byte
5
Destination Address
0
2
Bit
0
6
1
1
Comments
7
5
6
0
Bit
2
0
1
Gain Limit
0
7
15
1 Terminator (FFh)
6
1
5
1
4
1
3
1
2
1
1
1
0
1
3
2
AF Activation Time (L)
1
0
54
Command List
Enlargement Function2 Query Command ............. Command Packet 8x 09 7E 7E 04 FF
Byte
Bit
Comments
Byte
7
6
Destination Address
5
0
4
6
3
Source Address
1
0
1
2
3
0 Completion Message (50h)
6
1
5
0
4
1
3
0
2
0
1
0
0
0
7
Byte
Comments
7
0
6
0
6
0
5
0
5
0
4
0
4
0
11
3
0
2
WideD short exposure
2
0
1
Exposure ratio (L)
1
0
0
0
7
0
7
0
6
0
6
0
5
0
5
0
4
0
4
0
3
0
3
0
2
0
2
0
1
0
1
0
0
0
0
12
7
0
0
6
0
7
0
7
0
5
0
6
0
6
0
4
0
5
0
5
0
3
0
4
0
4
0
8
13
2
WideD mode (0: OFF, 1: ON,
3
0
3
0
1
2: Auto ON/OFF, 3: ON
2
0
2
0
0
(RatioFIx), 4: ON (Dver))
1
0
1
0
7
0
0
0
0
0
6
0
7
0
7
0
5
0
6
0
6
0
4
0
5
0
5
0
4
0
4
0
3
0
3
0
2
0
2
0
1
0
1
0
0
0
0
0
7
0
7
6
0
6
1
5
0
5
1
4
0
4
1
WideD blocked-up shadow
3
0
3
1
correction level 0: L 1: M 2: H
2
0
2
1
3: S
1
0
1
1
1
WideD blown-out highlight
0
0
0
1
0
correction level 0: L 1: M 2: H
3
WideD screen display
2
0: Combined image
9
2: Long-time 3: Short-time
1
WideD detection sensitivity
0
0: L 1: M 2: H
7
0
6
0
5
0
4
0
3
2
5
Bit
0
0
1: Long/short division
4
Comments
7
3
2
7
Bit
7
0
6
0
5
0
4
0
10
14
15
1 Terminator (FFh)
3
2
WideD short exposure
1
Exposure ratio (H)
0
55
Command List
VISCA Command Setting Values
Exposure control (1/2)
Gain
NTSC (s)
Shutter Speed
Iris
PAL (s)
0F
+28 dB
0E
+26 dB
0D
+24 dB
15
1/10000
1/10000
0C
+22 dB
14
1/6000
1/6000
0B
+20 dB
13
1/4000
1/3500
0A
+18 dB
12
1/3000
1/2500
09
+16 dB
11
1/2000
1/1750
08
+14 dB
10
1/1500
1/1250
07
+12 dB
0F
1/1000
1/1000
06
+10 dB
0E
1/725
1/600
05
+8 dB
0D
1/500
1/425
04
+6 dB
0C
1/350
1/300
03
+4 dB
0B
1/250
1/215
02
+2 dB
0A
1/180
1/150
01
0 dB
09
1/125
1/120
00
–3 dB
08
1/100
1/100
0F
+28 dB
07
1/90
1/75
0E
+26 dB
06
1/60
1/50
0D
+24 dB
05
1/30
1/25
0C
+22 dB
04
1/15
1/12
0B
+20 dB
03
1/8
1/6
0A
+18 dB
02
1/4
1/3
09
+16 dB
01
1/2
1/2
08
+14 dB
00
1/1
1/1
07
+12 dB
11
F1.35
06
+10 dB
10
F1.6
05
+8 dB
0F
F2
04
+6 dB
0E
F2.4
0D
F2.8
0C
F3.4
0B
F4
0A
F4.8
09
F5.6
08
F6.8
07
F8
06
F9.6
05
F11
04
F14
03
F16
02
F19
01
F22
00
CLOSE
Gain Limit
56
Command List
Exposure control (2/2)
Zoom Ratio and Zoom Position
(for reference)
IRIS
Bright
Exposure Comp.
GAIN
1F
F1.35
+28 dB
1E
F1.35
+26 dB
Zoom Ratio
×36 Lens
Optical Zoom
Positon Data
1D
F1.35
+24 dB
×1
0000
1C
F1.35
+22 dB
×2
15CA
1B
F1.35
+20 dB
×3
1F65
1A
F1.35
+18 dB
×4
2527
19
F1.35
+16 dB
×5
2921
18
F1.35
+14 dB
×6
2C22
17
F1.35
+12 dB
×7
2E88
16
F1.35
+10 dB
×8
3088
15
F1.35
+8 dB
×9
3242
14
F1.35
+6 dB
×10
33C9
13
F1.35
+4 dB
×11
3529
12
F1.35
+2 dB
×12
366C
11
F1.35
0 dB
×13
3795
10
F1.6
0 dB
×14
38A8
0F
F2
0 dB
×15
39A5
0E
F2.4
0 dB
×16
3A8E
0D
F2.8
0 dB
×17
3B61
0C
F3.4
0 dB
×18
3C1E
0B
F4
0 dB
×19
3CC7
0A
F4.8
0 dB
×20
3D5C
09
F5.6
0 dB
×21
3DDE
08
F6.8
0 dB
×22
3E50
07
F8
0 dB
F9.6
0 dB
×23
3EB3
06
3F09
05
F11
0 dB
×24
F14
0 dB
×25
3F53
04
03
F16
0 dB
02
F19
0 dB
01
F22
0 dB
00
CLOSE
0 dB
0E
+7
+10.5 dB
0D
+6
+9 dB
0C
+5
+7.5 dB
0B
+4
+6 dB
0A
+3
+4.5 dB
09
+2
+3 dB
08
+1
+1.5 dB
07
0
0 dB
06
–1
–1.5 dB
05
–2
–3 dB
04
–3
–4.5 dB
03
–4
–6 dB
02
–5
–7.5 dB
01
–6
–9 dB
00
–7
–10.5 dB
×26
3F94
×27
3FCD
×28
4000
57
Command List
Digital Zoom Combine mode
Title setting
X12-NTSC/PAL
Digital Zoom
Ratio
Digital Zoom
Position Data
×1
4000
Line number
00 to 0A
H-position
00 to 17
00: Dose not blink
Blink
01: Blinks
×2
6000
00
White
×3
6A80
01
Yellow
×4
7000
02
Violet
×5
7300
03
Red
×6
7540
04
Cyan
×7
76C0
05
Green
×8
7800
06
Blue
×9
78C0
Color
×10
7980
×11
7A00
×12
7AC0
Digital Zoom Separate mode
00
01
02
03
04
05
06
07
A
B
C
D
E
F
G
H
08
09
0a
0b
0c
0d
0e
0f
I
J
K
L
M
N
O
P
X12-NTSC/PAL
10
11
12
13
14
15
16
17
Digital Zoom
Ratio
Digital Zoom
Position Data
Q
R
S
T
U
V
W
X
18
19
1a
1b
1c
1d
1e
1f
×1
00
Y
Z
&
?
!
1
2
×2
80
20
21
22
23
24
25
26
27
×3
AA
3
4
5
6
7
8
9
0
×4
C0
28
29
2a
2b
2c
2d
2e
2f
×5
CC
À
È
Ì
Ò
Ù
Á
É
Í
×6
D5
30
31
32
33
34
35
36
37
×7
DB
Ó
Ú
Â
Ê
Ô
Æ
Œ
Ã
×8
E0
38
39
3a
3b
3c
3d
3e
3f
×9
E3
Õ
Ñ
Ç
ß
Ä
Ï
Ö
Ü
×10
E6
40
41
42
43
44
45
46
47
×11
E8
Å
$
F
¥
DM
£
¿
¡
×12
EB
48
49
4a
4b
4c
4d
4e
4f
ø
“
:
‘
.
,
/
-
Lens control
0000
Zoom Position
Focus Position
Wide end
1000
Far end
to
to
4000
to 7AC0
Optical
Tele end
Digital
Tele end
C000
2000: 12 m
3000: 5.6 m
Limit
4000: 4 m
5000: 2.7 m
As the distance on the left
will differ due to temperature
6000: 2 m
characteristics, etc., use as
7000: 1.5 m
approximate values.
8000: 80 cm
9000: 30 cm
Reading Value
pq (hex)
Near end
1000: Over Inf
Focus Near
Temperature Reading Conversion Value
(Reference Value)
* The lower 1 byte is fixed at
00.
Temperature
Conversion
Value (ºC)
00
–3 to 3
0A
7 to 13
14
17 to 23
1E
27 to 33
28
37 to 43
32
47 to 53
3C
57 to 63
A000: 19 cm
B000: 9 cm
C000: 1 cm
58
Command List
Register Setting
Others
The register settings are enabled when the power is
turned off and then back on again. After turning the
power back on again, verify that the mode settings
have been changed.
Register No.
VISCA
Baud Rate
OSD
Language
Value
60
CCD Scanning
Mode
72
Digital Output
Mode
* Enabled when
the CCD
Scanning Mode
is Progressive.
73
E-Zoom Max
to
FF
AF Interval Time
00
to
FF
Spot AE X position
00
to
0F
Spot AE Y position
00
to
0F
R Gain
00
to
FF
B Gain
00
to
FF
01
19200 bps
Aperture Level
00
to
0F
02
38400 bps
NR Level
00
to
05
00
English
03
Chinese
00
Interlaced
01
Progressive
00
60p/50p
(30p/25p × 2)
Clock rate:
56 MHz
01
04
Zoom Limit
00
1)
9600 bps
00
00
AF Active Time1)
V-Phase
00
to
020C (NTSC)
0270 (PAL)
AE Response
01
to
30
AutoICR ON t
OFF Threshold Level
00
to
1C
MD Threshold Level
00
to
FF
00
to
FF
1)
MD Interval Time
MD Set Horizontal Position
00
to
0C
60p/50p
Clock rate:
MD Set Vertical Position
00
to
08
56 MHz
Threshold Level
00
to
7F
30p/25p
Clock rate:
28 MHz
(Stop analog
output)
Color Enhancement
Hysteresis Width
00
to
7F
Color Enhancement
Fixed Color Y
00
to
7F
Color Enhancement
Fixed Color Cr2)
00
to
7F
Color Enhancement
Fixed Color Cb2)
00
to
7F
50
00-FF
Wide Limit
(0: Disabled)
51
00-FF
Tele Limit
(0: Disabled)
52
–
Max. digital
zoom ratio =
256 ÷
Color Enhancement
1)
Unit: One second
2)
40 center
(256-Value)
StableZoom
FocusTrace
53
00
OFF
01
ON
54
00
OFF
55
00-FF
@ZoomDirect
FocusOffset
@DomeCover
01
ON
00: None to
FF: Max.
59
Specifications
Specifications
FCB-EX995E/P
Picture elements FCB-EX995E: Approx. 380K pixels
FCB-EX995EP: Approx. 440K pixels
Horizontal resolution
550 TV lines (WIDE end)
Lens
28× zoom
F= 3.5 mm (WIDE) to 98.0 mm
(TELE), F1.35 to F3.7
Zoom movement speed
(NTSC)
Optical WIDE/Optical TELE
2.5 sec (Focus Tracking ON)
1.7 sec (Focus Tracking OFF)
Optical WIDE/Digital TELE
4.5 sec (Focus Tracking ON)
1.7 sec (Focus Tracking OFF)
Digital WIDE/Digital TELE 2.0 sec
(PAL)
Optical WIDE/Optical TELE
2.5 sec (Focus Tracking ON)
1.7 sec (Focus Tracking OFF)
Optical WIDE/Digital TELE
4.9 sec (Focus Tracking ON)
1.7 sec (Focus Tracking OFF)
Digital WIDE/Digital TELE 2.5 sec
Focus Movement time
∞ to Near
0.7 sec
Digital zoom
12× (324× with optical zoom)
Angle of view (H)
Approx. 55.8 degree (WIDE end) to
Approx. 2.1 degree (TELE end)
Min. working distance
10 mm (WIDE end), 1500 mm
(TELE end)
Sync system
Internal/External (V-Lock)
Min. illumination
(Interlace mode) 0.65 lux (F1.35, 50 IRE) (Typical
value)
0.04 lux/1/4 sec (NTSC), 1/3 sec
(PAL) (Typical value)
ICR-ON Mode
0.005 lux/1/4 sec (NTSC),
1/3 sec (PAL)
Recommended illumination
100 to 100,000 lux
S/N ratio
50 dB (Weight ON)
Back light compensation
ON/OFF
Electronic shutter speed
1/4 to 1/10000 sec. (20 steps)
White balance
AUTO, ATW, Indoor, Outdoor,
One Push WB, Manual WB,
Outdoor Auto, Sodium Vapor
Lamp (Fix/Auto)
Gain
Auto/Manual (–3 dB to +28 dB,
16 steps)
Max. Gain Limit (6 dB to 28 dB,
12 steps)
Wide dynamic range
ON/OFF/AUTO
3D noise reduction
ON/OFF (level 5 to 1 / OFF,
6 steps)
Image Stabilizer ON/OFF/HOLD
Color Enhancement
ON/OFF
Aperture control 16 steps
Preset
6-POSITIONS
Serial interface VISCA protocol (TTL/CMOS)
9.6 Kbps, 19.2 Kbps, 38.4 Kbps,
Stop bit, 1/2 bit
Video Output
VBS: 1.0 Vp-p (Sync negative),
Y/C Output
Digital (ITU-R BT656 equiv.)
Progressive/Interlace
Storage temperature/Humidity
–20 °C to +60 °C (–4 °F to +140 °F)/
20% to 95%
Operating temperature/Humidity
–5 °C to +60 °C (32 °F to +122 °F)/
20% to 80%
60
Specifications
Power requirements/Power consumption
6 to 12 V DC/2.2 W (5.0 W)
Weight
Approx. 268 g (9.4 oz.)
Dimensions
50.0 × 57.5 × 89.8 mm
(2 × 2 3/8 × 3 5/8 in.) (w/h/d)
Design and specifications are subject to change without
notice.
FCB-EX985E/P
Picture elements FCB-EX985E: Approx. 380K pixels
FCB-EX985EP: Approx. 440K pixels
Horizontal resolution
550 TV lines (WIDE end)
Lens
28× zoom
F= 3.5 mm (WIDE) to 98.0 mm
(TELE), F1.35 to F3.7
Zoom movement speed
(NTSC)
Optical WIDE/Optical TELE
2.5 sec (Focus Tracking ON)
1.7 sec (Focus Tracking OFF)
Optical WIDE/Digital TELE
4.5 sec (Focus Tracking ON)
1.7 sec (Focus Tracking OFF)
Digital WIDE/Digital TELE 2.0 sec
(PAL)
Optical WIDE/Optical TELE
2.5 sec (Focus Tracking ON)
1.7 sec (Focus Tracking OFF)
Optical WIDE/Digital TELE
4.9 sec (Focus Tracking ON)
1.7 sec (Focus Tracking OFF)
Digital WIDE/Digital TELE 2.5 sec
Focus Movement time
∞ to Near
0.7 sec
Digital zoom
12× (324× with optical zoom)
Angle of view (H)
Approx. 55.8 degree (WIDE end) to
Approx. 2.1 degree (TELE end)
Min. working distance
10 mm (WIDE end), 1500 mm
(TELE end)
Sync system
Internal/External (V-Lock)
Min. illumination
(Interlace mode) 0.25 lux (F1.35, 50 IRE) (Typical
value)
0.16 lux/1/4 sec (NTSC), 1/3 sec
(PAL) (Typical value)
ICR-ON Mode
0.0015 lux/1/4 sec (NTSC),
1/3 sec (PAL)
Recommended illumination
100 to 100,000 lux
S/N ratio
50 dB (Weight ON)
Back light compensation
ON/OFF
Electronic shutter speed
1/4 to 1/10000 sec. (20 steps)
White balance
AUTO, ATW, Indoor, Outdoor,
One Push WB, Manual WB,
Outdoor Auto, Sodium Vapor
Lamp (Fix/Auto)
Gain
Auto/Manual (–3 dB to +28 dB,
16 steps)
Max. Gain Limit (6 dB to 28 dB,
12 steps)
3D noise reduction
ON/OFF (level 5 to 1 / OFF,
6 steps)
Image Stabilizer ON/OFF/HOLD
Color Enhancement
ON/OFF
Aperture control 16 steps
Preset
6-POSITIONS
Serial interface VISCA protocol (TTL/CMOS)
9.6 Kbps, 19.2 Kbps, 38.4 Kbps,
Stop bit, 1/2 bit
Video Output
VBS: 1.0 Vp-p (Sync negative),
Y/C Output
Digital (ITU-R BT656 equiv.)
Interlace
Storage temperature/Humidity
–20 °C to +60 °C (–4 °F to +140 °F)/
20% to 95%
Operating temperature/Humidity
–5 °C to +60 °C (32 °F to +122 °F)/
20% to 80%
Power requirements/Power consumption
6 to 12 V DC/1.9 W (4.6 W)
Weight
Approx. 268 g (9.4 oz.)
Dimensions
50.0 × 57.5 × 89.8 mm
(2 × 2 3/8 × 3 5/8 in.) (w/h/d)
Design and specifications are subject to change
without notice.
61
Specifications
Digital Output Function
FCB-EX995E/P
Operation Mode
Digital Output (ITU-R BT656 equiv.)
Interlace
FCB-EX995E/P: 60i/50i, clock rate: 28 MHz
Interlace WD
Progressive
FCB-EX995E/P: 60p/50p, clock rate: 56 MHz
FCB-EX995E/P: 60p/50p (30p/25p × 2), clock rate: 56 MHz
FCB-EX995E/P: 30p/25p, clock rate: 28 MHz
FCB-EX995E/P: 60p/50p (30p/25p × 2), clock rate: 56 MHz
Progressive WD
FCB-EX995E/P: 30p/25p, clock rate: 28 MHz
Slow shutter is not available in the Interlace WD or Progressive WD mode.
FCB-EX985E/P
Operation Mode
Digital Output (ITU R BT656 equiv.)
Interlace
FCB-EX985E/P: 60i/50i, clock rate: 28 MHz
Digital Output Characteristics
DC characteristics
ITEM
SIGN
Rating Value
MIN
Output voltage
UNIT
MAX
Digtal Signal out [7] - [0]
Digital Clock
VOH1
2.58
V
MODEL
MODE
ITEM
SIGN
FCB-EX995E (NTSC)
Interlace
VOL1
0.4
V
AC characteristics
Progressive
FCB-EX995EP (PAL)
Interlace
Progressive
Typ
Clock cycle period
tcyc (ns)
35.2
Data output setup time
tsu (ns)
13.5
Data output hold time
thd (ns)
18.5
Clock cycle period
tcyc (ns)
17.6
Data output setup time
tsu (ns)
12.5
Data output hold time
thd (ns)
2.5
Clock cycle period
tcyc (ns)
35.2
Data output setup time
tsu (ns)
14.6
Data output hold time
thd (ns)
18.5
Clock cycle period
tcyc (ns)
17.4
Data output setup time
tsu (ns)
5.5
Data output hold time
thd (ns)
9.5
62
Specifications
FCB Interior – Digital Output
Resistance
Ferrite
Beads
Connector
Ferrite Beads
Product number: BK20104M241-T (Taiyo Yuden)
Impedance Frequency Characteristics (Reference)
63
Specifications
Digital Output Timing [50p mode]
Horizontal
1H = 1816CLK
4CLK
4CLK
SAV
BLK
1504CLK Effective pixel
4CLK
4CLK
304CLK
BLK
EAV
BLK
Y
Cr
Y
Cb
Y
Y
Cr
Cb
Y3
Cr1
Y2
Y1
Cb1
Cr0
Cb0
Data out [0-7]
Y0
CLK [56.75 MHz]
625H
Vertical
582H Effective line
24H
BLK
2H
19H
BLK
BLK
Data out [0-7]
BLK : Black data (Y 10, Cb/Cr 80)
Digital Output Timing [25p mode]
Horizontal
1H = 1816CLK
4CLK
4CLK
SAV
BLK
1504CLK Effective pixel
4CLK
4CLK
BLK
EAV
304CLK
BLK
Y
Cr
Y
Cb
Y
Cr
Y
Cb
Y3
Cr1
Y2
Cb1
Y1
Cr0
Cb0
Data out [0-7]
Y0
CLK [28.375 MHz]
625H
Vertical
24H
BLK
582H Effective line
2H
19H
BLK
BLK
Data out [0-7]
BLK : Black data (Y 10, Cb/Cr 80)
64
Specifications
Digital Output Timing [60p mode]
Horizontal
1H = 1820CLK
4CLK
4CLK
SAV
BLK
1536CLK Effective pixel
4CLK
4CLK
276CLK
BLK
EAV
BLK
Y
Cr
Y
Cb
Y
Y
Cr
Cb
Y3
Cr1
Y2
Y1
Cb1
Cr0
Cb0
Data out [0-7]
Y0
CLK [57.2727 MHz]
525H
Vertical
494H Effective line
20H
BLK
2H
11H
BLK
BLK
Data out [0-7]
BLK : Black data (Y 10, Cb/Cr 80)
Digital Output Timing [30p mode]
Horizontal
1H = 1820CLK
4CLK
4CLK
SAV
BLK
1536CLK Effective pixel
4CLK
4CLK
BLK
EAV
276CLK
BLK
Y
Cr
Y
Cb
Y
Cr
Y
Cb
Y3
Cr1
Y2
Cb1
Y1
Cr0
Cb0
Data out [0-7]
Y0
CLK [28.6363 MHz]
525H
Vertical
20H
BLK
494H Effective line
2H
11H
BLK
BLK
Data out [0-7]
BLK : Black data (Y 10, Cb/Cr 80)
65
Specifications
Digital Output Timing [60i mode]
Horizontal
1H = 1820CLK
4CLK
4CLK
SAV
BLK
1536CLK Effective pixel
4CLK
4CLK
276CLK
BLK
EAV
BLK
Vertical
Y
Cr
Y
Cb
Y
Y
Cr
Cb
Y3
Cr1
Y2
Y1
Cb1
Cr0
Cb0
Data out [0-7]
Y0
CLK [28.6363 MHz]
FLD1 ODD LINE
FLD2
2H
13H
BLK
BLK
FLD2 EVEN LINE
247H Effective line
3H
3H
13H
BLK
BLK
BLK
247H Effective line
3H
2H
BLK
BLK
Data out [0-7]
BLK : Black data (Y 10, Cb/Cr 80)
Digital Output Timing [50i mode]
Horizontal
1H = 1816CLK
4CLK
4CLK
SAV
BLK
1504CLK Effective pixel
4CLK
4CLK
304CLK
BLK
EAV
BLK
Vertical
FLD1 ODD LINE
FLD2
2H
19H
BLK
BLK
291H Effective line
Y
Cr
Y
Cb
Y
Cr
Y
Cb
Y3
Cr1
Y2
Cb1
Y1
Cr0
Cb0
Data out [0-7]
Y0
CLK [28.375 MHz]
FLD2 EVEN LINE
1H
3H
19H
BLK
BLK
BLK
291H Effective line
1H
2H
BLK BLK
Data out [0-7]
BLK : Black data (Y 10, Cb/Cr 80)
66
Specifications
FCB-EX985E
Digital Output Timing [NTSC interlace mode]
Horizontal
1H = 1820CLK
1536CLK Effective pixel
4CLK
4CLK
SAV
Black data
4CLK
4CLK
276CLK
Black data
EAV
BLK
Vertical
Y
Cr
Y
Cb
Y
Cr
Y
Cb
Y3
Cr1
Y2
Cb1
Y1
Y0
Cb0
Data out [0-7]
Cr0
CLK [28.375 MHz]
FLD1 ODD LINE
FLD2
FLD2 EVEN LINE
247H
Effective line
2H
13H
BLK
BLK
3H
Black
data
247H
Effective line
3H
13H
BLK
BLK
2H
3H
Black
data
BLK
Data out [0-7]
BLK : Black data (Y 10, Cb/Cr 80)
FCB-EX985E
Digital Output Timing [PAL interlace mode]
Horizontal
1H = 1816CLK
4CLK
4CLK
SAV
Black data
1504CLK Effective pixel
4CLK
Black data
4CLK
304CLK
EAV
BLK
Vertical
FLD1 ODD LINE
FLD2
2H
19H
BLK
BLK
Y
Cr
Y
Cb
Y
Cr
Y
Cb
Y3
Cr1
Y2
Cb1
Y1
Cr0
Cb0
Data out [0-7]
Y0
CLK [28.375 MHz]
FLD2 EVEN LINE
291H
Effective line
1H
Black
data
3H
19H
BLK
BLK
291H
Effective line
1H
Black
data
2H
BLK
Data out [0-7]
BLK : Black data (Y 10, Cb/Cr 80)
67
Specifications
DIGITAL Image Output Y, Cr, Cb 4:2:2 FORMAT
68
Specifications
Dimensions
Front
Right side
89.8
85.4
(4.4)
50
48.3±0.1
7.5
25
ø3
10
25.4±0.1
21±0.1
(30)
30
57.5
(ø36.1)
(27.5)
6.1
73±0.1
4-M2
Within a depth of 3 mm (1/8 in.)
or less form the side
Top
Left side
2-M2
Within a depth of 3 mm (1/8 in.)
or less form the side
33.9
CN200 12P
Digital output
82.7
(33.9)
14±0.1
5
20±0.1
20±0.1
4.5
20.9
CN702 12P
12.5
20±0.1
9-M2
Within a depth of 3 mm (1/8 in.)
or less form the top surface
28±0.1
Bottom
Back
1/4-20UNC (Tripod screw for camera)
Within a depth of 7 mm (9/32 in.) or
less form the bottom surface
8-M2
64.5
14±0.1
CN501 9P
CN503 4P
Y/C
7.55
9.5
16±0.1
27±0.1
17.5
Within a depth of 3 mm
(1/8 in.) or less form the
bottom surface
33.5
37.7
29±0.1
33±0.1
Unit: mm (inches)
69
Specifications
Frequency: 60 Hz ±1 Hz (FCB-EX995E)
50 Hz ±1 Hz (FCB-EX995EP)
Amplitude: 3 V ±0.5 V square wave (50% duty)
CMOS level
V Phase Adjustment Range: 0° to 360° from V SYNC
falling edge
Pin assignment
Recommended Input Waveform
CN503
J.S.T. Mfg Co. S4B-ZR-SM4A-TF(LF)
Pin No.
Name
1
Y_Out
2
GND (for Y signal)
3
C_Out
4
GND (for C signal)
Level
1.0 Vp-p (75 ohm),
luminance signal
Chrominance signal
CN702
KYOCERA ELCO Co. 086222012101848+
Pin No.
CN501
KYOCERA ELCO Co. 00 6200 509 130 000+
Pin No.
Name
Level
1
RxD
CMOS 5 V (low: max 0.8 V,
high: min 2.0 V) Read Data
2
TxD
CMOS 5 V (low: max 0.1 V,
high: min 4.4 V) Send Data
3
GND (for RxD&TxD)
4
DC IN
5
GND (for DC IN)
6
VBS OUT
7
GND (for VBS OUT)
8
V LOCK PULSE
9
GND (VL PULSE)
Name
1
GND
2
GND
3
KEY AD0
4
KEY AD1
5
KEY AD2
6
KEY AD3
7
KEY AD4
8
KEY AD5
9
KEY AD6
10
KEY AD7
11
NC
12
Strobe
Level
9.0 V±3 V
1.0 V±0.2 V
External VD-Lock Pulse
(EX.FV: Negative, 3 Vp-p
50% duty)
70
Specifications
CN200
KYOCERA ELCO Co. 086222012101848+
Pin No.
Name
Level
1
GND
2
Digital Out 0
0 - 3.3 Vp-p
3
Digital Out 1
0 - 3.3 Vp-p
4
Digital Out 2
0 - 3.3 Vp-p
5
Digital Out 3
0 - 3.3 Vp-p
6
Digital Out 4
0 - 3.3 Vp-p
7
Digital Out 5
0 - 3.3 Vp-p
8
Digital Out 6
0 - 3.3 Vp-p
9
Digital Out 7
0 - 3.3 Vp-p
10
GND
11
CLOCK
12
GND
0 - 3.3 Vp-p
Note
Image noise may occur when using digital output. Take measures
such as attaching a ferrite core to the FFC as needed. The
recommended maximum FFC length is 150 mm.
Strobe signal specifications
71
Download PDF
Similar pages