PN-H701
LCD MONITOR
USER MANUAL
IMPORTANT:
To aid reporting in case of loss or theft, please record the
product’s model and serial numbers in the space provided.
The numbers are located in the rear of the product.
Model No.:
Serial No.:
U.S.A. ONLY
SAFETY PRECAUTIONS
Electricity is used to perform many useful functions, but it can also cause personal injuries and property damage if improperly
handled. This product has been engineered and manufactured with the highest priority on safety. However, improper use can
result in electric shock and/or fire. In order to prevent potential dange , please observe the following instructions when installing,
operating and cleaning the product. To ensure your safety and prolong the service life of your LCD product, please read the
following precautions carefully before using the product.
1. Read instructions — All operating instructions must be read and understood before the product is operated.
2. Keep
this manual in a safe place — These safety and operating instructions must be kept in a safe place for future
reference.
3. Observe warnings — All warnings on the product and in the instructions must be observed closely.
4. Follow instructions — All operating instructions must be followed.
5. Cleaning — Unplug the power cord from the AC outlet before cleaning the product. Use a dry cloth to clean the product. Do
not use liquid cleaners or aerosol cleaners.
6. Attachments — Do not use attachments not recommended by the manufacturer. Use of inadequate attachments can result
in accidents.
7. Water and moisture — Do not use the product near water. Do not install the product in a place where water may splash onto
it. Be careful of equipment which drains water such as an air-conditioner.
8. Ventilation — The vents and other openings in the cabinet are designed for ventilation.
Do not cover or block these vents and openings since insufficient ventilation can cause overheating and/or shorten the lif
of the product. Do not place the product on a sofa, rug or other similar surface, since they can block ventilation openings.
Do not place the product in an enclosed place such as a bookcase or rack, unless proper ventilation is provided or the
manufacturer’s instructions are followed.
9. Power cord protection — The power cords must be routed properly to prevent people from stepping on them or objects from
resting on them.
10. The LCD panel used in this product is made of glass. Therefore, it can break when the product is dropped or applied with
impact. Be careful not to be injured by broken glass pieces in case the LCD panel breaks.
11. Overloading — Do not overload AC outlets or extension cords. Overloading can cause fire or electric shock
12. Entering of objects and liquids — Never insert an object into the product through vents or openings. High voltage flows i
the product, and inserting an object can cause electric shock and/or short internal parts.
For the same reason, do not spill water or liquid on the product.
13. Servicing — Do not attempt to service the product yourself. Removing covers can expose you to high voltage and other
dangerous conditions. Request a qualified service person to perform servicing
14. Repair — If any of the following conditions occurs, unplug the power cord from the AC outlet, and request a qualified servic
person to perform repairs.
a. When the power cord or plug is damaged.
b. When a liquid was spilled on the product or when objects have fallen into the product.
c. When the product has been exposed to rain or water.
d. When the product does not operate properly as described in the operating instructions.
Do not touch the controls other than those described in the operating instructions. Improper adjustment of controls
not described in the instructions can cause damage, which often requires extensive adjustment work by a qualifie
technician.
e. When the product has been dropped or damaged.
f. When the product displays an abnormal condition. Any noticeable abnormality in the product indicates that the product
needs servicing.
15. Replacement parts — In case the product needs replacement parts, make sure that the service person uses replacement
parts specified by the manufacture , or those with the same characteristics and performance as the original parts. Use of
unauthorized parts can result in fire, electric shock and/or other dange .
16. Safety checks — Upon completion of service or repair work, request the service technician to perform safety checks to
ensure that the product is in proper operating condition.
17. Wall mounting — When mounting the product on a wall, be sure to install the product according to the method
recommended by the manufacturer.
18. Heat sources — Keep the product away from heat sources such as radiators, heaters, stoves and other heat-generating
products (including amplifiers)
19. Batteries — Incorrect use of batteries may cause the batteries to burst or ignite. A leaky battery may corrode the equipment,
dirty your hands or spoil your clothing. In order to avoid these problems, make sure to observe the precautions below:
• Use the specified batteries onl .
• Install the batteries with due attention to the plus (+) and minus (-) sides of the batteries according to the instructions in the
compartment.
• Do not mix old and new batteries.
• Do not mix batteries of different types. Voltage specifications of batteries of the same shape may var .
• Replace an exhausted battery with a new one promptly.
• If you will not use the remote control for a long time, remove the batteries.
• If leaked battery fluid gets on your skin or clothing, rinse immediately and thoroughl . If it gets into your eye, bathe your
eye well rather than rubbing and seek medical treatment immediately. Leaked battery fluid that gets into your eye or you
clothing may cause a skin irritation or damage your eye.
20. Usage of the monitor must not be accompanied by fatal risks or dangers that, could lead directly to death, personal injury,
severe physical damage or other loss, including nuclear reaction control in nuclear facility, medical life support system, and
missile launch control in a weapon system.
SAFETY PRECAUTIONS (Continued)
WARNING:
1) This is a Class A product. In a domestic environment this product may cause radio interference in which case the user may
be required to take adequate measures.
2) Batteries shall not be exposed to excessive heat such as sunshine, fire or the like
3) To prevent injury, this apparatus must be securely attached to the floor/wall in accordance with the installation instructions
4) An apparatus with CLASS I construction shall be connected to a MAIN socket outlet with a protective earthing connection.
To maintain compliance with EMC regulations, use shielded cables to connect to the following terminals: HDMI input terminal
and PC D-sub input terminal.
If a monitor is not positioned in a sufficiently stable location, it can be potentially hazardous due to falling. Many injuries,
particularly to children, can be avoided by taking simple precautions such as:
• Using fixing devices like wall mount brackets recommended by the manufacture .
• Only using furniture that can safely support the monitor.
• Ensuring the monitor is not overhanging the edge of the supporting furniture.
• Not placing the monitor on tall furniture (for example, cupboards or bookcases) without anchoring both the furniture and the
monitor to a suitable support.
• Not standing the monitors on cloth or other materials placed between the monitor and supporting furniture.
• Educating children about the dangers of climbing on furniture to reach the monitor or its controls.
Especially for child safety
- Don’t allow children to climb on or play with the monitor.
- Don’t place the monitor on furniture that can easily be used as steps, such as a chest of drawers.
- Remember that children can become excited while watching a program, especially on a “larger than life” monitor. Care
should be taken to place or install the monitor where it cannot be pushed, pulled over, or knocked down.
- Care should be taken to route all cords and cables connected to the monitor so that they cannot be pulled or grabbed by
curious children.
IMPORTANT SAFETY INSTRUCTIONS
1)
2)
3)
4)
5)
6)
7)
8)
9)
10)
1)
1
12)
3)
1
14)
Read these instructions.
Keep these instructions.
Heed all warnings.
Follow all instructions.
Do not use this apparatus near water.
Clean only with dry cloth.
Do not block any ventilation openings. Install in accordance with the manufacturer’s instructions.
Do not install near any heat sources such as radiators, heat registers, stoves, or other apparatus (including amplifiers) tha
produce heat.
Do not defeat the safety purpose of the polarized or grounding-type plug. A polarized plug has two blades with one wider
than the other. A grounding type plug has two blades and a third grounding prong. The wide blade or the third prong are
provided for your safety. If the provided plug does not fit into your outlet, consult an electrician for replacement of th
obsolete outlet.
Protect the power cord from being walked on or pinched particularly at plugs, convenience receptacles, and the point
where they exit from the apparatus.
Only use attachments/accessories specified by the manufacture .
Use only with the cart, stand, tripod, bracket, or table specified by the manufacture , or sold with the apparatus.
When a cart is used, use caution when moving the cart/apparatus combination to avoid injury from tip-over.
Unplug this apparatus during lightning storms or when unused for long periods of time.
Refer all servicing to qualified service personnel. Servicing is required when the apparatus has been damaged in an
way, such as power-supply cord or plug is damaged, liquid has been spilled or objects have fallen into the apparatus, the
apparatus has been exposed to rain or moisture, does not operate normally, or has been dropped.
ENGLISH
21. Do
not stay in contact with the parts of the product that become hot for long periods of time. Doing so may result in
low-temperature burns.
22. To prevent fire or shock hazard, do not expose this product to dripping or splashing
No objects filled with liquids, such as vases, should be placed on the product
23. This product must only be connected to a 100-240V, 50/60Hz, grounded (3-prong) outlet.
SAFETY INSTRUCTION
-Do not use the monitor where there is a lot of dust, where humidity
is high, or where the monitor may come into contact with oil or
steam. Do not use in an environment where there are corrosive
gases (sulfur dioxide, hydrogen sulfide, nitrogen dioxide, chlo ine,
ammonia, ozone, etc.). As this could lead to fire
-E
nsure that the monitor does not come into contact with water
or other fluids. Ensure that no objects such as paper clips or
pins enter the monitor as this could lead to fire or electric s ock.
- Do not place the monitor on top of unstable objects or in
unsafe places. Do not allow the monitor to receive strong
shocks or to strongly vibrate. Causing the monitor to fall or
topple over may damage it.
- Do not use the monitor near heating equipment or in places
where there is likelihood of high temperature, as this may
lead to generation of excessive heat and outbreak of fire
- Do not use the monitor in places where it may be exposed to
direct sunlight.
- Please be sure to constantly remove dust and garbage that
has attached to the ventilation opening. If dust collects in the
ventilation opening or the inside of the monitor, it may lead to
excessive heat, outbreak of fire, or malfunction
Please request a cleaning of the inside of the monitor from
an authorized SHARP servicing dealer or service center.
- The AC outlet shall be installed near the equipment and shall
be easily accessible.
The Power Cord
- Use only the power cord supplied with the monitor.
- Do not damage the power cord nor place heavy objects on
it, stretch it or over bend it. Also, do not add extension cords.
Damage to the cord may result in fire or electric shock
- Do not use the power cord with a power tap.
Adding an extension cord may lead to fire as a result of
overheating.
- Do not remove or insert the power plug with wet hands.
Doing so could result in electric shock.
- Unplug the power cord if it is not used for a long time.
- Do not attempt to repair the power cord if it is broken
or malfunctioning. Refer the servicing to the service
representative.
MOUNTING PRECAUTIONS
• This product is for use indoors.
• A mounting bracket compliant with VESA specifications i
required.
• Since the monitor is heavy, consult your dealer before
installing, removing or moving the monitor.
• Mounting the monitor on the wall requires special expertise
and the work must be performed by an authorized SHARP
dealer. You should never attempt to perform any of this work
yourself. Our company will bear no responsibility for accidents
or injuries caused by improper mounting or mishandling.
• Use the monitor with the surface perpendicular to a level
surface. If necessary, the monitor may be tilted up to 20
degrees upward or downward.
• This monitor should be used at an ambient temperature
between 32°F (0°C) and 104°F (40°C). Provide enough space
around the monitor to prevent heat from accumulating inside.
For the monitor in landscape orientation
Unit: inch [mm]
7-7/8 [200]
1-3/8 [35]
• Temperature condition may change when using the monitor
together with the optional equipments recommended by
SHARP. In such cases, please check the temperature
condition specified by the optional equipments
• Do not block any ventilation openings. If the temperature
inside the monitor rises, this could lead to a malfunction.
• Do not place the monitor on a device which generates heat.
• Adhere to the following when installing the monitor in its
portrait orientation. Failing to adhere to the following may
cause malfunctions.
- Install the monitor such that the power LED is located on
the bottom side.
- Set the MONITOR on the MONITOR menu to PORTRAIT.
(See OPERATION MANUAL.)
• When installing the monitor in the portrait orientation, and
the internal temperature of the monitor rises excessively,
the brightness of the backlight automatically decreases in
order to prevent a further temperature rise.
• Use the supplied sticker.
For the monitor in landscape orientation
2
[50]
2
[50]
2 [50]
For the monitor in portrait orientation
7-7/8 [200]
Unit: inch [mm]
1-3/8 [35]
Horizontal sticker
(Logo)
For the monitor in portrait orientation
2
[50]
2
[50]
Vertical sticker
(Operation panel)
2 [50]
Power LED
• If it is difficult to provide sufficient space for any reason s h
as the installation of the monitor inside a housing, or if the
ambient temperature may be outside of the range of 32°F
(0°C) to 104°F (40°C), install a fan or take other measures to
keep the ambient temperature within the required range.
Be careful not to cover the remote control sensor or buttons.
Supplied Components
 Liquid Crystal Display Monitor: 1
 Remote control unit: 1
 Cable clamp: 4
 Cable clamp (insertion type): 2
 Power cord: 1
 R-6 battery (“AA” size): 2
 CD-ROM (Utility Disk for Windows): 1
 Setup Manual: 1
 Power cord clamp: 1
 Power cord clamp screw: 1
 USB flash drive cover:
 USB flash drive cover screw:
 Horizontal sticker (Logo): 1
 Vertical sticker (Operation panel): 1
 RS-232C conversion cable (Φ3.5 mini-jack): 1
 USB extension cable (about 20 cm): 1
* SHARP Corporation holds authorship rights to the Utility Disk program. Do not reproduce it without permission.
* For environmental protection!
Do not dispose of batteries in household waste. Follow the disposal instructions for your area.
Preparing the Remote Control Unit
1. Press the cover gently and slide it in the direction of the arrow.
2. See the instructions in the compartment and put in the supplied batteries (R-6 (“AA” size) x 2) with their plus (+) and minus (-)
sides oriented correctly.
3. Close the cover.
ENGLISH
If any component should be missing, please contact your dealer.
Connections
Caution
• Be sure to turn off the main power switch and disconnect the plug from the power outlet before connecting/disconnecting
cables. Also, read the manual of the equipment to be connected.
• Be careful not to confuse the input terminal with the output terminal when connecting cables. Accidentally reversing cables
connected to the input and output terminals may cause malfunctions and the other problems.
7
8
9
10
11
12
1.
2.
3.
4.
5.
6.
7.
8.
9.
10.
11.
12.
AC input terminal
PC D-sub input terminal
LAN terminal
Digital audio output (optical) terminal
Audio input terminal
CONTROL terminal
(RS-232C input terminal)
Headphone terminal
USB port
HDMI1 input terminal
HDMI2 input terminal
HDMI3 input terminal
HDMI4 input terminal
1
2
3
4
5
6
Power cord
(Supplied)
For power outlet
TIPS
• Set the audio input terminal used for each input mode in AUDIO SELECT of AUDIO TERMINAL SETTING in the SETUP
menu. The factory settings are shown below.
Input mode
Video
Audio input terminal (Factory setting)
INPUT1
HDMI1 input terminal
HDMI1 input terminal
INPUT2
HDMI2 input terminal
HDMI2 input terminal
INPUT3
HDMI3 input terminal
HDMI3 input terminal/Audio input terminal *1
INPUT4
HDMI4 input terminal
HDMI4 input terminal
INPUT5
PC D-sub input terminal
Audio input terminal *2
MULTIMEDIA
USB port / Internal memory
USB port / Internal memory
*1Select the terminal to be used in HDMI of AUDIO SELECT.
*2Select the terminal to be used in PC D-SUB of AUDIO SELECT.
• The terms HDMI and HDMI High-Definition Multimedia Interface, a d the HDMI Logo are trademarks or registered trademarks
of HDMI Licensing LLC in the United States and other countries.
Turning Power On/Off
Turning power on/off
• Turn on the monitor first before turning on the PC o
playback device.
Press the POWER button or POWER switch to turn the power
ON/OFF.
Turning on the main power
Main power switch
Power switch
Status
Caution
• The main power must be turned on/off with the main power
switch. Do not connect/disconnect the power cord or turn
the breaker on/off while the main power switch is on.
• When switching the main power switch or the POWER
button off and back on, always wait for at least 5 seconds.
• For a complete electrical disconnection, pull out the main
plug.
Power LED
Status of the monitor
Green lit
Power on
Orange lit
Power off (Standby mode)
Accessing the operation panel
ENGLISH
Caution
Specifications
Model
Power requirement
Operating temperature *
Operating humidity
Power consumption
Dimensions (excluding protrusions)
Weight
PN-H701
AC 100 - 240 V, XX A, 50/60 Hz
32°F to 104°F (0°C to 40°C)
20% to 80% (no condensation)
XX W
inch (mm) Approx. 61-3/8 (W) x 2-3/4 (D) x 31-1/4 (H) (1559 x 69 x 794)
lbs. (kg) Approx. 83.8 (38)
* Temperature condition may change when using the monitor together with the optional equipments recommended by SHARP. In such
cases, please check the temperature condition specified by the optional equipments
As a part of our policy of continuous improvement, SHARP reserves the right to make design and specification changes fo product improvement
without prior notice. The performance specification figures indicated are nominal values of production units There may be some deviations from
these values in individual units.
Mounting Precautions (For SHARP dealers and service engineers)
• When installing, removing or moving the monitor, ensure that this is carried out by at least 3 people.
• Be sure to use a wall-mount bracket designed or designated for mounting the monitor.
• This monitor is designed to be installed on a concrete wall or pillar. Reinforced work might be necessary for some materials
such as plaster / thin plastic board / wood before starting installation.
• This monitor and bracket must be installed on a wall which can endure at least 4 times or more the weight of the monitor.
Install by the most suitable method for the material and the structure.
• To attach a VESA-compliant mounting bracket, use M6 screws that are 5/16 inch (8 mm) to 3/8 inch (10 mm) longer than the
thickness of the mounting bracket.
• Do not use an impact driver.
• When moving the monitor, be sure to hold the areas shown in the figure belo . Do not hold the LCD panel. This may cause
product damage, failure, or injury.
• After mounting, please carefully ensure the monitor is secure, and not able to come loose from the wall or mount.
• Do not use any screw holes other than VESA holes for installation.
PN-H701
LCD MONITOR
Additional information
(Compatible Graphics Cards)
Overview
This information describes how to connect PN-H701 with various computer graphics cards.
(This information is as of January 2015).
Digital terminals of PN-H701
・This product is equipped with HDMI® terminals. DisplayPort™ terminals are not included.
・For a 3840 × 2160 (60 Hz) video signal
- HDMI input terminals 1,2 & 3 are compatible with RGB / YCbCr 4:4:4, 4:2:2, and 4:2:0 formats.
- HDMI input terminal 4 is compatible with RGB / YCbCr 4:2:0 format.
Connecting with Graphics Cards
・Recommended Graphics cards that support 4K resolution are as follows. Details are listed below.
Also, refer to the manual of the equipment to be connected.
【4K (3860x2160@60Hz)
-
HDMI2.0 output graphics cards :
【4K (3860x2160@30Hz)
-
-
input】
NVIDIA - GTX980/970
(HDMI2.0 support)
input】
HDMI 1.4a output graphics
cards :
NVIDIA - GTX780/750/650Ti
:
Intel
:
Mac Book Pro2013 and Mac Pro2013
DVI and DisplayPort output graphics cards :
- Haswell HD4400
NVIDIA -Quadro K5000 / K4200 / K2200 / K600 *
* DVI to HDMI adapter or DisplayPort to HDMI adapter (Suggested adapter or similar: DisplayPort™ 1.2 to HDMI
4K Active Type 2 Adaptor ) allows connection to graphics cards supporting 4k 30p.
-If black looks lighter / not true black,
Set(Contrast 39、Black level : -14)in Main menu.
-If gradient banding occurs, Set(Contrast 26、Black level :+16)in Main menu.
®
Table of tested graphics cards
[HDMI output graphics cards]
Video Card /
Vender
PC
GTX980
4K
4K
FHD
(3840x2160)
(3840x2160)
(1920x1080)
@60Hz
@30Hz
@60Hz
HDMI
HDMI
HDMI
HDMI
1~3
4
1~4
1~4
Driver
Output
input
input
input
input
347.09
HDMI
OK
NG *1
OK
OK
Note
*1 Available.
However,
GTX970
NVIDIA
GTX750
Decreases gradation
HDMI
GTX780
347.09
HDMI
NG
NG *1
Haswell
10.18.
HD4400
10.3960
OK
OK
OK
OK
4K
4K
FHD
(3840x2160)
(3840x2160)
(1920x1080)
@60Hz
@30Hz
@60Hz
HDMI
HDMI
HDMI
1~4
1~4
1~4
input
input
input
HDMI
(not adjustable)
NA
MacBook
Mac
OK
HDMI
GTX650Ti
Intel
OK
HDMI
Pro 2013/
(HDMI1.4a)
Mac Pro
[DVI and DisplayPort output graphics cards]
Video Card /
Vender
PC
Driver
Output
Note
Quadro
*2
K5000
DVI-HDMI
Quadro
NVIDIA
K4200
347.09
or
Quadro
DP - HDMI
K2200
adapter*2
Quadro
K600
DVI-HDMI or
DisplayPort-HDMI
NA
OK*3
OK*4
Active type2 adapter
needed.
*3 Driver setting : Full
*4Driver setting: Limited
PN-H701
LCD MONITOR
OPERATION MANUAL
IMPORTANT:
To aid reporting in case of loss or theft, please record the
product’s model and serial numbers in the space provided.
The numbers are located in the rear of the product.
Model No.:
Serial No.:
U.S.A. ONLY
IMPORTANT INFORMATION
WARNING: TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK, DO NOT EXPOSE THIS PRODUCT
TO RAIN OR MOISTURE.
CAUTION
RISK OF ELECTRIC
SHOCK
DO NOT OPEN
CAUTION: TO REDUCE THE RISK OF ELECTRIC
SHOCK, DO NOT REMOVE COVER.
NO USER-SERVICEABLE PARTS
INSIDE.
REFER SERVICING TO QUALIFIED
SERVICE PERSONNEL.
The lightning flash with arrowhead symbol, within
a triangle, is intended to alert the user to the
presence of uninsulated “dangerous voltage”
within the product’s enclosure that may be of
sufficient magnitude to constitute a risk of electric
shock to persons.
The exclamation point within a triangle is
intended to alert the user to the presence of
important operating and maintenance (servicing)
instructions in the literature accompanying the
product.
WARNING:
FCC Regulations state that any unauthorized changes or modifications to this equipment not expressly approved by the
manufacturer could void the user’s authority to operate this equipment.
NOTE:
This equipment has been tested and found to comply with the limits for Class A digital device, pursuant to Part 15 of the
FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment
is operated in a commercial environment. This equipment generates, uses, and can radiate radio frequency energy and, if
not installed and used in accordance with the instruction manual, may cause harmful interference to radio communications.
Operation of this equipment in a residential area is likely to cause harmful interference in which case the user will be required
to correct the interference at his own expense.
U.S.A. ONLY
3
E
DEAR SHARP CUSTOMER
Thank you for your purchase of a SHARP LCD product. To ensure safety and many years of trouble-free operation of your
product, please read the Safety Precautions carefully before using this product.
SAFETY PRECAUTIONS
Electricity is used to perform many useful functions, but it can also cause personal injuries and property damage if improperly
handled. This product has been engineered and manufactured with the highest priority on safety. However, improper use can
result in electric shock and/or fire. In order to prevent potential dange , please observe the following instructions when installing,
operating and cleaning the product. To ensure your safety and prolong the service life of your LCD product, please read the
following precautions carefully before using the product.
1. Read instructions — All operating instructions must be read and understood before the product is operated.
2. Keep
this manual in a safe place — These safety and operating instructions must be kept in a safe place for future
reference.
3. Observe warnings — All warnings on the product and in the instructions must be observed closely.
4. Follow instructions — All operating instructions must be followed.
5. Cleaning — Unplug the power cord from the AC outlet before cleaning the product. Use a dry cloth to clean the product. Do
not use liquid cleaners or aerosol cleaners.
6. Attachments — Do not use attachments not recommended by the manufacturer. Use of inadequate attachments can result
in accidents.
7. Water and moisture — Do not use the product near water. Do not install the product in a place where water may splash onto
it. Be careful of equipment which drains water such as an air-conditioner.
8. Ventilation — The vents and other openings in the cabinet are designed for ventilation.
Do not cover or block these vents and openings since insufficient ventilation can cause overheating and/or shorten the lif
of the product. Do not place the product on a sofa, rug or other similar surface, since they can block ventilation openings.
Do not place the product in an enclosed place such as a bookcase or rack, unless proper ventilation is provided or the
manufacturer’s instructions are followed.
9. Power cord protection — The power cords must be routed properly to prevent people from stepping on them or objects from
resting on them.
10. The LCD panel used in this product is made of glass. Therefore, it can break when the product is dropped or applied with
impact. Be careful not to be injured by broken glass pieces in case the LCD panel breaks.
11. Overloading — Do not overload AC outlets or extension cords. Overloading can cause fire or electric shock
12. Entering of objects and liquids — Never insert an object into the product through vents or openings. High voltage flows i
the product, and inserting an object can cause electric shock and/or short internal parts.
For the same reason, do not spill water or liquid on the product.
13. Servicing — Do not attempt to service the product yourself. Removing covers can expose you to high voltage and other
dangerous conditions. Request a qualified service person to perform servicing
14. Repair — If any of the following conditions occurs, unplug the power cord from the AC outlet, and request a qualified servic
person to perform repairs.
a. When the power cord or plug is damaged.
b. When a liquid was spilled on the product or when objects have fallen into the product.
c. When the product has been exposed to rain or water.
d. When the product does not operate properly as described in the operating instructions.
Do not touch the controls other than those described in the operating instructions. Improper adjustment of controls
not described in the instructions can cause damage, which often requires extensive adjustment work by a qualifie
technician.
e. When the product has been dropped or damaged.
f. When the product displays an abnormal condition. Any noticeable abnormality in the product indicates that the product
needs servicing.
15. Replacement parts — In case the product needs replacement parts, make sure that the service person uses replacement
parts specified by the manufacture , or those with the same characteristics and performance as the original parts. Use of
unauthorized parts can result in fire, electric shock and/or other dange .
16. Safety checks — Upon completion of service or repair work, request the service technician to perform safety checks to
ensure that the product is in proper operating condition.
17. Wall mounting — When mounting the product on a wall, be sure to install the product according to the method
recommended by the manufacturer.
18. Heat sources — Keep the product away from heat sources such as radiators, heaters, stoves and other heat-generating
products (including amplifiers)
E
4
SAFETY PRECAUTIONS (Continued)
19. Batteries
— Incorrect use of batteries may cause the batteries to burst or ignite. A leaky battery may corrode the equipment,
dirty your hands or spoil your clothing. In order to avoid these problems, make sure to observe the precautions below:
• Use the specified batteries onl .
• Install the batteries with due attention to the plus (+) and minus (-) sides of the batteries according to the instructions in the
compartment.
• Do not mix old and new batteries.
• Do not mix batteries of different types. Voltage specifications of batteries of the same shape may var .
• Replace an exhausted battery with a new one promptly.
• If you will not use the remote control for a long time, remove the batteries.
• If leaked battery fluid gets on your skin or clothing, rinse immediately and thoroughl . If it gets into your eye, bathe your
eye well rather than rubbing and seek medical treatment immediately. Leaked battery fluid that gets into your eye or you
clothing may cause a skin irritation or damage your eye.
20. Usage of the monitor must not be accompanied by fatal risks or dangers that, could lead directly to death, personal injury,
severe physical damage or other loss, including nuclear reaction control in nuclear facility, medical life support system, and
missile launch control in a weapon system.
21. Do not stay in contact with the parts of the product that become hot for long periods of time. Doing so may result in
low-temperature burns. If you need to move the monitor after it has been in use, it may be hot. Turn off the power and make
sure it has cooled sufficiently before moving
22. To prevent fire or shock hazard, do not expose this product to dripping or splashing
No objects filled with liquids, such as vases, should be placed on the product
23. This product must only be connected to a 100-240V, 50/60Hz, grounded (3-prong) outlet.
WARNING:
1) This is a Class A product. In a domestic environment this product may cause radio interference in which case the user may
be required to take adequate measures.
2) Batteries shall not be exposed to excessive heat such as sunshine, fire or the like
3) To prevent injury, this apparatus must be securely attached to the floor/wall in accordance with the installation instructions
4) An apparatus with CLASS I construction shall be connected to a MAIN socket outlet with a protective earthing connection.
To maintain compliance with EMC regulations, use shielded cables to connect to the following terminals: HDMI input terminal
and PC D-sub input terminal.
If a monitor is not positioned in a sufficiently stable location, it can be potentially hazardous due to falling. Many injuries,
particularly to children, can be avoided by taking simple precautions such as:
• Using fixing devices like wall mount brackets recommended by the manufacture .
• Only using furniture that can safely support the monitor.
• Ensuring the monitor is not overhanging the edge of the supporting furniture.
• Not placing the monitor on tall furniture (for example, cupboards or bookcases) without anchoring both the furniture and the
monitor to a suitable support.
• Not standing the monitors on cloth or other materials placed between the monitor and supporting furniture.
• Educating children about the dangers of climbing on furniture to reach the monitor or its controls.
Especially for child safety
- Don’t allow children to climb on or play with the monitor.
- Don’t place the monitor on furniture that can easily be used as steps, such as a chest of drawers.
- Remember that children can become excited while watching a program, especially on a “larger than life” monitor. Care
should be taken to place or install the monitor where it cannot be pushed, pulled over, or knocked down.
- Care should be taken to route all cords and cables connected to the monitor so that they cannot be pulled or grabbed by
curious children.
5
E
IMPORTANT SAFETY INSTRUCTIONS
1)
2)
3)
4)
5)
6)
7)
8)
9)
10)
1)
1
12)
3)
1
14)
E
6
Read these instructions.
Keep these instructions.
Heed all warnings.
Follow all instructions.
Do not use this apparatus near water.
Clean only with dry cloth.
Do not block any ventilation openings. Install in accordance with the manufacturer’s instructions.
Do not install near any heat sources such as radiators, heat registers, stoves, or other apparatus (including amplifiers) tha
produce heat.
Do not defeat the safety purpose of the polarized or grounding-type plug. A polarized plug has two blades with one wider
than the other. A grounding type plug has two blades and a third grounding prong. The wide blade or the third prong are
provided for your safety. If the provided plug does not fit into your outlet, consult an electrician for replacement of th
obsolete outlet.
Protect the power cord from being walked on or pinched particularly at plugs, convenience receptacles, and the point where
they exit from the apparatus.
Only use attachments/accessories specified by the manufacture .
Use only with the cart, stand, tripod, bracket, or table specified by the manufacture , or sold with the apparatus.
When a cart is used, use caution when moving the cart/apparatus combination to avoid injury from tip-over.
Unplug this apparatus during lightning storms or when unused for long periods of time.
Refer all servicing to qualified service personnel. Servicing is required when the apparatus has been damaged in an
way, such as power-supply cord or plug is damaged, liquid has been spilled or objects have fallen into the apparatus, the
apparatus has been exposed to rain or moisture, does not operate normally, or has been dropped.
TIPS AND SAFETY INSTRUCTIONS
-The TFT color LCD panel used in this monitor is made with
the application of high precision technology. However, there
may be minute points on the screen where pixels never light
or are permanently lit. Also, if the screen is viewed from
an acute angle there may be uneven colors or brightness.
Please note that these are not malfunctions but common
phenomena of LCDs and will not affect the performance of
the monitor.
-Do not display a still picture for a long period, as this could
cause a residual image.
- Never rub or tap the monitor with hard objects.
The Power Cord
-Use only the power cord supplied with the monitor.
-Do not damage the power cord nor place heavy objects on
it, stretch it or over bend it. Also, do not add extension cords.
Damage to the cord may result in fire or electric shock
-Do not use the power cord with a power tap.
Adding an extension cord may lead to fire as a result of
overheating.
-Do not remove or insert the power plug with wet hands.
Doing so could result in electric shock.
-Please understand that SHARP CORPORATION bears no
responsibility for errors made during use by the customer or
a third party, nor for any other malfunctions or damage to this
product arising during use, except where indemnity liability is
recognized under law.
-Unplug the power cord if it is not used for a long time.
-This monitor and its accessories may be upgraded without
advance notice.
Manual Scope
-Do not use the monitor where there is a lot of dust, where
humidity is high, or where the monitor may come into contact
with oil or steam. Do not use in an environment where
there are corrosive gases (sulfur dioxide, hydrogen sulfide,
nitrogen dioxide, chlorine, ammonia, ozone, etc.). As this
could lead to fire
-Ensure that the monitor does not come into contact with
water or other fluids. Ensure that no objects such as paper
clips or pins enter the monitor as this could lead to fire or
electric shock.
-Do not place the monitor on top of unstable objects or in
unsafe places. Do not allow the monitor to receive strong
shocks or to strongly vibrate. Causing the monitor to fall or
topple over may damage it.
-Do not use the monitor near heating equipment or in places
where there is likelihood of high temperature, as this may
lead to generation of excessive heat and outbreak of fire
-Do not use the monitor in places where it may be exposed to
direct sunlight.
-Please be sure to constantly remove dust and garbage that
has attached to the ventilation opening. If dust collects in the
ventilation opening or the inside of the monitor, it may lead to
excessive heat, outbreak of fire, or malfunction
Please request a cleaning of the inside of the monitor from
an authorized SHARP servicing dealer or service center.
-Images cannot be rotated on this monitor.
When using in portrait orientation, you will need to prepare
appropriately orientated content in advance.
-The AC outlet shall be installed near the equipment and shall
be easily accessible.
-Do not attempt to repair the power cord if it is broken
or malfunctioning. Refer the servicing to the service
representative.
-Microsoft, Windows and Internet Explorer are registered
trademarks of Microsoft Corporation.
-The terms HDMI and HDMI High-Definition Multimedia
Interface, and the HDMI Logo are trademarks or registered
trademarks of HDMI Licensing LLC in the United States and
other countries.
-Adobe, Acrobat, and Reader are either registered trademarks
or trademarks of Adobe Systems Incorporated in the United
States and/or other countries.
-MHL, the MHL logo, and Mobile High-Definition Link are
trademarks or registered trademarks of MHL, LLC in the
United States and other countries.
-The monitor is manufactured based on a license from Dolby
Laboratories.
-Dolby and Double D Signal are trademarks of Dolby
Laboratories.
-All other brand and product names are trademarks or
registered trademarks of their respective holders.
-Language of OSD menu used in this manual is English by
way of example.
-Illustrations in this manual may not exactly represent the
actual product or display.
-This manual assumes use in landscape orientation, except
where specifically noted
LED Backlight
● The LED backlight in this product has a limited lifetime.
* If the screen gets dark or does not turn on, it may be
necessary to replace the LED backlight.
* This LED backlight is exclusive to this product and must
be replaced by an authorized SHARP servicing dealer
or service center. Please contact an authorized SHARP
servicing dealer or service center for assistance.
7
E
MOUNTING PRECAUTIONS
• This product is for use indoors.
• A mounting bracket compliant with VESA specifications i
required.
• Since the monitor is heavy, consult your dealer before
installing, removing or moving the monitor.
• Mounting the monitor on the wall requires special expertise
and the work must be performed by an authorized SHARP
dealer. You should never attempt to perform any of this
work yourself. Our company will bear no responsibility
for accidents or injuries caused by improper mounting or
mishandling.
• Use the monitor with the surface perpendicular to a level
surface. If necessary, the monitor may be tilted up to 20
degrees upward or downward.
• This monitor should be used at an ambient temperature
between 32°F (0°C) and 104°F (40°C). Provide
enough space around the monitor to prevent heat from
accumulating inside.
For the monitor in landscape orientation
Unit: inch [mm]
7-7/8 [200]
1-7/16 [35]
• Adhere to the following when installing the monitor in its
portrait orientation. Failing to adhere to the following may
cause malfunctions.
- Install the monitor such that the power LED is located on
the bottom side.
- Set the MONITOR on the MONITOR menu to PORTRAIT.
(See page 28.)
• When installing the monitor in the portrait orientation, and
the internal temperature of the monitor rises excessively,
the brightness of the backlight automatically decreases in
order to prevent a further temperature rise.
• Use the supplied sticker.
For the monitor in landscape orientation
Horizontal sticker
(Logo)
For the monitor in portrait orientation
2
[50]
2
[50]
2 [50]
For the monitor in portrait orientation
7-7/8 [200]
Unit: inch [mm]
1-7/16 [35]
Be careful not to cover the remote control sensor or
switches.
2
[50]
2
[50]
2 [50]
Power LED
• If it is difficult to provide sufficient space for any reas
such as the installation of the monitor inside a housing, or
if the ambient temperature may be outside of the range
of 32°F (0°C) to 104°F (40°C), install a fan or take other
measures to keep the ambient temperature within the
required range.
• Temperature condition may change when using the monitor
together with the optional equipments recommended by
SHARP. In such cases, please check the temperature
condition specified by the optional equipments
• Do not block any ventilation openings. If the temperature
inside the monitor rises, this could lead to a malfunction.
• Do not place the monitor on a device which generates heat.
E
8
Vertical sticker
(Operation panel)
Supplied Components
If any component should be missing, please contact your dealer.
 Liquid Crystal Display Monitor: 1
 Remote control unit: 1
 Cable clamp: 4
 Cable clamp (insertion type): 2
 Power cord: 1
 LR-6 battery (“AA” size): 2
 CD-ROM (Utility Disk for Windows): 1
 Setup Manual: 1
 Power cord clamp: 1
 Power cord clamp screw: 1
 USB flash drive cover:
 USB flash drive cover screw:
 Horizontal sticker (Logo): 1
 Vertical sticker (Operation panel): 1
 RS-232C conversion cable (3.5 mm mini jack): 1
 USB extension cable: 1
* SHARP Corporation holds authorship rights to the Utility Disk program. Do not reproduce it without permission.
* For environmental protection!
Do not dispose of batteries in household waste. Follow the disposal instructions for your area.
9
E
Part Names
nFront view
Accessing the operation panel
1
1.
2.
3.
4.
5.
LCD panel
Remote control sensor (See page 16.)
Input switch (See page 18.)
Power switch (See page 17.)
Power LED (See page 17.)
TIPS
• Use a pointed object such as a pen tip to press the
switches.
3
2
4
5
nRear view
1
2
11
12
13
14
15
3
3
4
5
6
E
10
7
8
9
10
16
1.
2.
3.
4.
5.
6.
7.
8.
9.
10.
11.
12.
13.
14.
15.
16.
Vents
USB flash drive cover (See page 15.)
Speakers
Main power switch (See page 17.)
AC input terminal (See page 14.)
PC D-sub input terminal (See page 13.)
LAN terminal (See page 13.)
Digital audio output (optical) terminal
(See page 13.)
Audio input terminal (See page 13.)
CONTROL terminal
(RS-232C input terminal) (See page 13.)
Headphone terminal (See page 13.)
USB port (See page 13.)
HDMI1 input terminal (See page 12.)
HDMI2 input terminal (See page 12.)
HDMI3 input terminal (See page 12.)
HDMI4 input terminal (See page 12.)
Part Names
nRemote control unit
1
1.
2.
3.
4.
2
7
3
8
4
9
10
5
5.
6.
7.
8.
9.
10.
11.
Signal transmitter
POWER button (See page 17.)
MUTE button (See page 18.)
VOL +/- buttons (See page 18.)
Cursor control ( /
/
/ ) buttons
DISPLAY/F1 button (See page 18.)
MODE/F2 button (See page 18.)
INPUT button (See page 18.)
MENU button (See page 18.)
ENTER button (See page 18.)
RETURN button (See page 18.)
SIZE/F3 button (See page 18.)
11
6
11
E
Connecting Peripheral Equipment
8
6
1
2
3
4
5
Caution
• Be sure to turn off the main power switch and disconnect
the plug from the power outlet before connecting/
disconnecting cables. Also, read the manual of the
equipment to be connected.
• Be careful not to confuse the input terminal with the output
terminal when connecting cables. Accidentally reversing
cables connected to the input and output terminals may
cause malfunctions and the other problems.
• Do not use any cable that has a damaged or deformed
terminal. Using such cables may cause malfunctions.
11
1.
2.
3.
4.
•
•
•
•
•
•
E
12
7
10
Connection with a PC or AV equipment
TIPS
• Images may not be displayed properly depending on the
computer (video card) to be connected.
• Perform automatic adjustment using SCREEN POSITION
of INPUT SELECT in the SETUP menu when a PC screen
is displayed using D-SUB, or when the setting of the PC is
changed.
• If the audio output from the playback device is connected
directly to speakers or other devices, the video on the
monitor may appear delayed from the audio portion.
Audio should be played through this monitor by connecting
the playback device to the monitor’s audio input, and
connecting the monitor’s audio output to the speakers or
other devices.
9
HDMI1 input terminal
HDMI2 input terminal
HDMI3 input terminal
HDMI4 input terminal
Connect with a commercially available HDMI certifie
cable. For the following, use a high-speed HDMI cable:
- When connecting a device that is compatible with 4K2K
output.
- When inputting a 1080p video signal
The HDMI1 input terminal is compatible with ARC (Audio
Return Channel).
To connect an ARC-compatible audio device using an
HDMI cable, connect to the HDMI1 input terminal.
When using the audio input terminal with HDMI input,
use the HDMI3 input terminal and set AUDIO SELECT of
INPUT SELECT in the SETUP menu to HDMI + ANALOG.
The HDMI4 input terminal is compatible with MHL (Mobile
High-Definition Link)
An MHL-compatible smartphone can be connected
using a commercially available MHL cable to show video
from the smartphone on the monitor while charging
the smartphone. When a MHL is connect, the input is
automatically switched to HDMI4.
This product supports MHL1.
Compatible copyright protection signals
- HDMI1 - 3 input terminals: HDCP1.4
- HDMI4 input terminal: HDCP2.2
When the connection between HDMI1 to HDMI3 and HDMI4
is switched, it could be necessary to reconfigure the compute .
For a 3840 × 2160 (60 Hz) video signal
- HDMI1 - 3 input terminals are compatible with 4:4:4,
4:2:2, and 4:2:0 formats.
- HDMI4 input terminal is only compatible with 4:2:0 format.
- If input in 4:4:4 format is not necessary, use the HDMI4
input terminal. If an HDMI1 - 3 input terminal is used,
the video or audio may not be output correctly.
Connecting Peripheral Equipment
• Compatible audio signals
- Type: Linear PCM (2 ch), AAC, Dolby Digital
- Sampling frequency: 48kHz / 44.1kHz / 32kHz
• Use an HDMI cable connector with the following dimensions:
9. Digital audio output (optical) terminal
• You can output MPEG2 AAC / Dolby Digital audio format
from the monitor.
• Use the following for the digital audio output (optical)
terminal.
Thickness: 1/2 inch (12 mm)
or less
5. PC D-sub input terminal
• When using the audio input terminal with the PC D-sub
input terminal, set AUDIO SELECT of INPUT SELECT in
the SETUP menu to VIDEO + AUDIO.
• When using the PC D-sub input terminal, space is
required behind the monitor.
6. USB port
• Connect a USB flash drive to the USB port
• Do not connect a USB device other than a USB flas
drive.
• Turn off the power of the monitor when removing a USB
flash drive
Thickness: 1/2 inch (12 mm)
or less
10. CONTROL terminal (RS-232C input terminal)
• The monitor can be connected to a PC using the RS232C conversion cable (supplied) and a commercially
available RS-232 straight cable to control the monitor
from the PC.
11. LAN terminal
• You can control the monitor from a PC on a network by
connecting a commercially available LAN cable between
this terminal and a network.
Supported USB flash drives
File System
Capacity
FAT32
Up to 32 GB
(maximum file size 2 GB
• Do
not use a USB flash drive with a security function o
a write protection function.
• Use a USB flash drive with a shape that can be inserte
in the USB port. Some USB flash drives with specia
shapes cannot be inserted. Do not forcibly insert a USB
flash drive. This may damage the connector and cause
failure.
7. Audio input terminal
• This is used to input analog audio when video is shown
using the HDMI3 input terminal or the PC D-sub input
terminal. Check the setting in AUDIO SELECT of INPUT
SELECT in the SETUP menu.
• Use an audio cable without resistance.
8. Headphone terminal
• Use commercially available headphones (mini stereo
jack).
• The output sound varies depending on the input mode.
• The volume can be adjusted using the volume adjustment.
• When headphones are connected to the headphone
terminal, sound is not output from the monitor speakers.
13
E
Connecting the Power Cord
Caution
• Use only the power cord supplied with the monitor.
1. Turn off the main power switch.
2. Plug the power cord (supplied) into the AC input terminal.
3. Plug the power cord (supplied) into the AC power outlet.
Main power switch
1
AC input terminal
2
Power cord (Supplied)
3 For power
outlet
Binding Cables
The cables connected to the terminals on the rear of the monitor can be fastened with the cable clamp.
Power cord (Supplied)
*1
Power cord clamp screw
*1
Power cord clamp
*2
Caution
*2
*1 *2
*1
*1
*1
*1
*1
• Do not tighten the screw excessively. Excessive
tightening may damage the monitor.
*1
*2
Cable clamp
(insertion type)
Cable
Cable clamp
attachment
Cable clamp
E
14
Cable clamp
attachment
Cable
Setting the USB flash drive cover
1. Insert the USB flash drive into the USB port.
2.Attach the USB flash drive cover and secure with the
provided screw.
USB port
USB flash drive
cover screw
Caution
• Do not tighten the screw excessively. Excessive tightening may damage the monitor.
TIPS
• If the USB flash drive will be ttached, use a USB flash drive with dimensions no greater than 1-15/16 inch (50 mm) (L)
13/16 inch (20 mm) (W) × 1/2 inch (12 mm) (H).
15
E
Preparing the Remote Control Unit
Installing the batteries
1. Press the cover gently and slide it in the direction of the arrow.
2. See the instructions in the compartment and put in the supplied batteries (LR-6 (“AA” size) x 2) with their plus (+) and minus (-)
sides oriented correctly.
3. Close the cover.
TIPS
•
•
•
•
When the batteries become exhausted, replace them with new (commercially available) batteries.
The supplied batteries (LR-6 (“AA” size) x 2) may become exhausted quickly depending on how they are stored.
If you will not be using the remote control for a long time, remove the batteries.
Use manganese or alkaline batteries only.
Remote control operation range
Operation panel in
The remote control can be operated even when the operation panel is stored inside the monitor.
Point the remote control toward the remote control sensor on the bottom of the monitor (or the right side of the monitor if using
portrait orientation).
For the monitor in landscape orientation
For the monitor in portrait orientation
16.4 feet (5m)
16.4 feet (5m)
10º
45º
16.4 feet
(5m)
10º 10º
10º
10º
Remote control sensor
10º
16.4 feet
(5m)
Remote control
sensor
45º
10º
10º
Operation panel out
Point the remote control toward the remote control sensor on the front of the monitor.
For the monitor in landscape orientation
For the monitor in portrait orientation
16.4 feet (5m)
10º
10º
10º
16.4 feet
(5m)
16.4 feet (5m)
10º
Remote control
sensor
Remote
control
sensor
16.4 feet
(5m)
10º 10º
10º 10º
TIPS
•
•
•
•
•
•
•
E
16
Do not expose the remote control unit to shock by dropping or stepping on it. This could lead to a malfunction.
Do not expose the remote control unit to liquids, and do not place it in an area with high humidity.
The remote control unit may not work properly if the remote control sensor is under direct sunlight or strong lighting.
Objects between the remote control unit and the remote control sensor may prevent proper operation.
Replace the batteries when they run low as this may shorten the remote control’s operation range.
If a fluoresce t light is illuminated near the remote control unit, it may interfere with proper operation.
Do not use it with the remote control of other equipment such as air conditioner, stereo components, etc.
Turning Power On/Off
Caution
Turning power on/off
• Turn on the monitor first before turning on the PC o
playback device.
Press the POWER button or POWER switch to turn the power
ON/OFF.
Turning on the main power
Main power switch
Power switch
Status
Caution
• The main power must be turned on/off with the main power
switch. Do not connect/disconnect the power cord or turn
the breaker on/off while the main power switch is on.
• When turning the power off and back on, always wait for at
least 5 seconds.
• For a complete electrical disconnection, pull out the main
plug.
Power LED
Status of the monitor
Green lit
Power on
Orange lit
Power off (Standby mode)
It is possible to check the power LED even when the operation
panel is stored inside the monitor.
Power LED
Caution
• When turning the power off and back on, always wait for at
least 5 seconds. A short interval may result in a malfunction.
TIPS
• When the main power switch is off, the monitor cannot be
turned on.
Disabling power on/off operations
Power on/power off operations can be disabled in order to
protect the monitor from an accidental power off. Set the
POWER BUTTON LOCK in FUNCTION menu. (See page 30.)
17
E
Basic Operation
4. VOL +/- (Volume adjustment)
1
Pressing
or
displays the volume menu when the
menu screen is not displayed.
30
Auto
Volume
2
3
4
Press
or
to adjust the volume of the sound.
* If you do not press any buttons for about 3 seconds, the
volume menu automatically disappears.
5. ENTER
Confirms the setting
5
6
9
7
6. RETURN
Returns to the previous screen.
7. DISPLAY/F1
Displays monitor information (input mode, resolution, etc.).
8
8. MODE/F2 (Picture mode selection)
Each time you press this button, the picture mode changes in
the following order:
1. INPUT (Input mode selection)
The menu is displayed. Press
or
to select the input
ENTER
mode, and press
to enter.
* You can select the input mode that shows SELECTABLE.
* You can select the input mode by pressing the input switch
of the monitor.
Video and audio input terminals for each input mode are
shown below.
Input mode
Video
Audio
HDMI1
HDMI1 input terminal
HDMI1 input terminal
HDMI2
HDMI2 input terminal
HDMI3
HDMI3 input terminal
HDMI4
HDMI4 input terminal
HDMI2 input terminal
HDMI3 input terminal/
Audio input terminal *1
HDMI4 input terminal
D-SUB
PC D-sub input terminal Audio input terminal *2
USB port / Internal
USB port
memory
MULTIMEDIA *3
*1When using the audio input terminal with HDMI3, set
AUDIO SELECT of INPUT SELECT in the SETUP menu to
HDMI + ANALOG. (See page 27.)
*2When using the audio input terminal, set AUDIO SELECT
of INPUT SELECT in the SETUP menu to VIDEO + AUDIO.
(See page 27.)
*3MULTIMEDIA menu is displayed in landscape.
When a USB flash drive is connected, the input mode
automatically changes to MULTIMEDIA.
2. MUTE
Turns off the volume temporarily.
Press the MUTE button again to turn the sound back to the
previous level.
3. MENU
Displays and turns off the menu screen. (See page 24.)
E
18
PC* → PHOTO → sRGB → DYNAMIC →
HIGH RESOLUTION → AV → MOVIE → GAME → PC...
* PC applies to HDMI1 - HDMI4, D-SUB only.
• sRGB is international standard of color representation
specified by IEC (International Electrotechnica
Commission). Color conversion is made in taking account
of liquid crystal’s characteristics and represents color tone
close to its original image.
9. SIZE/F3 (Screen size selection)
The screen size menu is displayed.
Press
or
to select the screen size. (See page 19.)
TIPS
DISPLAY
MODE
SIZE
• 7
(F1), 8
(F2), and 9
(F3) are also used in
MULTIMEDIA and during character entry.
Basic Operation
nSwitching the screen size
Even when the screen size is changed, the display may remain the same depending on the input signal.
NORMAL
Displays image so it fills the screen without changing the aspect ratio of the
input signals.
WIDE
Displays image so it fills the entire screen
DOT BY DOT
Displays the dots of the signals input from the connected PC as the corresponding
dots on the screen. When the image resolution is 1920x1080 pixels or lower, the
image is expanded to twice the height and width of the original.
UNDERSCAN
Displays the image of the input signal without modification
ZOOM
Displays a CinemaScope or 16:9 size video content in full-screen mode.
TIPS
• Using this monitor’s screen-size switching or dual-screen display functions to compress or expand the screen for commercial
or public viewing in establishments like cafes or hotels may infringe on the rights of the creators, as protected by Copyright
Law, so please be careful.
• The appearance of the original video may change if you select a screen size with a different aspect ratio than the original
image (e.g. TV broadcast or video input from external equipment).
• When an ordinary non-wide image (4:3) is viewed with the whole screen using the screen-size switching function of this
monitor, the edge of the image may be lost or appear distorted. If you wish to respect the creator’s intentions, set the screen
size to “NORMAL”.
• When playing commercial software, parts of the image (like subtitles) may be cropped. In this case select the optimal screen
size using the screen-size switching function of this monitor. With some software, there may be noise or distortion at the
edges of the screen. This is due to the characteristics of the software, and is not a malfunction.
• Depending on the original image size, black bands may remain at the edges of the screen.
• Input signals under 4K2K resolution are displayed in 3840 x 2160 resolution level by upscaling. (Except for DOT BY DOT)
19
E
Playing files
You can play photo, music, and video files in a USB flash drive
connected to the monitor, or photo files in internal memor .
For information on USB flash drive, see page 13
n Supported formats
The types of files that can be played are as follows
The operation of formats not indicated in the table is not guaranteed.
Photo files
Extension
Playing files
Play files in a USB flash drive
• You can play photo, music, and video files in a USB fla
drive connected to the monitor.
• You can have photo files play automatically when a US
flash drive is connected or the power is turned on. (See
page 22.)
Display size
*.jpg (*.jpeg, *.jpe)
32 x 32 - 8192 x 8192
• Progressive JPEG files are not supported
• Supported color formats are YUV4:4:4/YUV4:2:2/YUV4:2:0.
Music files
Extension
Audio codec
Play files in internal memory
• You can play photo files in internal memor . The photo fil
must first be copied to internal memor . (See page 21.)
• You can have photo files play automatically when the powe
is turned on. (See page 22.)
n Select the media from which the file will play
*.mp3
MPEG-1 L3
*.wav
WAV (LPCM)
*.wma
WMA
1. Change an input mode to MULTIMEDIA. (See page 18.)
When a USB flash drive is connected, the input mode
automatically changes to MULTIMEDIA.
*.m4a
AAC (MPEG4)
2. Press
DISPLAY
(F1).
3. Select the media with
Video files
Video files up to Full HD can be played
Extension
Video codec
Audio codec
*.m2ts
MPEG2/H.264
AAC, AC-3, MP3, LPCM
*.mp4
H.264
AAC, AC-3, MP3
*.3gp
H.264
AAC
*. mov
H.264
AAC, AC-3, MP3, LPCM
• Both video codec and audio codec need to be supported.
• The recommended frame rate for video 30 fps.
• In some cases it may not be possible to play the above files
• Do not place files other than the above in memory fo
playback.
• When file names or folder names are long, some character
may not appear in the list screen.
• Do not use a file that is over 2 GB
E
20
or
4. When you have finished, press
.
ENTER
.
Playing files
n Playing files
TIPS
For the actions that you can take in each screen, see page 22
to 23.
1. Select the type of file to be played with
ENTER
press
.
or
, and
, and press
ENTER
• To play a file select the fil with
,
,
ENTER
and press
.
Move to the previous fil during display with
to the next fil with
.
• You can play a slideshow.
or
2. Select the folder with
3. Select and play the file.
or
.
Photo files
. Move
MODE
(F2) to show the slideshow photo
(1)Press
selection screen.
(2)Select each fil with
,
,
or
, and press
SIZE
(F3) to check or uncheck the checkbox.
Files with checkmarks are played in the slideshow.
(3)To start the slideshow, press
MODE
(F2).
Music files / Video files
• To play a file select the fil with
or
and press
ENTER
.
• You can select a fil and press SIZE (F3) to check or
uncheck the checkbox.
When playing a checked file checked file are played in
order.
When plyaing an unchecked file only that fil is played.
4. End playback
RETURN
.
Music files
• Press
MODE
n Copy photo files to internal memory
You can copy photo file from a USB flas drive to internal
memory and play the files
1. Insert the USB flash drive into a USB port on the
monitor. (See page 13.)
2. Set the media to USB flash drive. (See page 20.)
ENTER
3. Select PHOTO with
or
and press
.
4. Select the folder that contains the files to be copied
ENTER
with
or
and press
.
DISPLAY
5. Press
(F1), select COPY PHOTO with
and press ENTER.
or
6. Select the file copy method and press ENTER.
• ALL FOLDER
Copy all file in a USB flas drive to the internal memory.
• CURRENT FOLDER
Copy all file in the selected folder to the internal memory.
• SELECTED FILE
Photo files / Video files
• Press
RETURN
• To return to the previous item, press
.
• The slideshow and auto play (see page 22) order is the
same as the order of the file shown in the list. If the fil
order is changed, the play order will also change. (See
page 23.)
• In a portrait installation, a portrait photo may occasionally
appear in landscape orientation. If this occurs, set the EXIF
information (rotation information) in the fil to no rotation
using an image processing program on your computer.
• If you stop a video fil before it is finishe playing and then
press ENTER to play the file the fil will resume from the point
where it was stopped. To play the fil from the beginning,
start playback with MODE (F2).
• The preview view of the video list may take time to appear
with some files Wait until the previews appear before
performing the next step.
(F2).
Playing music files in slide show
When playing a slideshow using photos in a USB flas drive,
you can play multiple music files
ENTER
1. Select PHOTO with
or
and press
.
ENTER
or
and press
.
2. Select the folder with
MODE
(F2) to show the slideshow photo selection
3. Press
screen, and select photos.
DISPLAY
(F1) in the slideshow photo selection
4. Press
screen, select SELECT SLIDE SHOW BGM with
or
ENTER
, and then press
.
ENTER
.
5. Check the media, and press
6. Select the folder that contains the files you want to
play with
or
, and press ENTER.
7. Select files.
SIZE
Select each fil with
or
, and press
(F3) to
check or uncheck the checkbox.
Files with checkmarks are played at the same time as the
RETURN
slideshow. When it is finished press
.
RETURN
8. When you have finished selecting the files, press
to return to the slideshow photo selection screen.
MODE
(F2) to start the slideshow.
9. Press
When playing a slideshow using photos in a USB flas
drive, you can play multiple music files
You can select file to be copied with
,
,
or
,
SIZE
and then press
(F3). When you have finishe selecting
MODE
files press
(F2).
7. Press ENTER.
8. Select the folder where the file will be copied to.
You can select CREATE NEW FOLDER to create a new
folder.
ENTER
9. Select YES with
or
and press
.
File copying starts. To cancel while the fil is being copied,
press
ENTER
(CANCEL).
10.When copying finishes, press
ENTER
.
TIPS
• Files cannot be copied from internal memory to a USB flas
drive.
21
E
Playing files
n Delete multiple photo files from internal memory
n To stop auto play
1. Set the media to INTERNAL MEMORY. (See page 20.)
1. Press
2. Select PHOTO with
or
and press
ENTER
DISPLAY
or
4. Press
(F1), select DELETE PHOTE with
ENTER
and press
, and then delete the file.
Operations during play
n Photo files
Operation is possible using the buttons below.
/
Auto playback
DISPLAY
Photos in a USB flash drive or the internal memory can be
played automatically.
MODE
SIZE
n Preparations
Prepare the photo files
1. Create a folder named “autoplay” in the root folder of
a USB flash drive or the internal memory, and copy the
photo files to be automatically played to the folder.
Select whether EXTERNAL STORAGE or INTERNAL
MEMORY is used for auto play.
MENU
, select OTHERS with
or
2. Select MULTIMEDIA AUTOPLAY with
press ENTER.
3. Select the media that is used with
or
ENTER
.
INTERNAL MEMORY : Internal memory
EXTERNAL STORAGE : USB flash driv
4. Press
MENU
and press
.
n Auto playback of files
Operation depends on the MULTIMEDIA AUTOPLAY setting.
• INTERNAL MEMORY
Turn on the monitor power.
Auto play starts.
• EXTERNAL STORAGE
Connect a USB flash drive (see page 13) and turn on
the monitor power.
Auto play starts.
You can connect a USB flash drive (see page 13) after
turning on the monitor power.
Auto play starts.
• Auto play plays all photo files in the “autoplay” folde . The
files that are played cannot be selected
• The auto play order is the same as the order of the files i
the list. To change the play order, change the order of the
files in the list. (See page 23.
• If the folder or a file format does not meet the abov
conditions for the folder or file format (see page 20), o
if MULTIMEDIA AUTOPLAY is not correctly set in the
OTHERS menu, auto playback will not start.
E
22
:End playback.
n Music files
Operation is possible using the buttons below.
ENTER
:Pause the file that is being played
ENTER
To resume playing the paused file, press
.
/
DISPLAY
MODE
:Adjust the volume of the sound.
(F1) :Show the Function menu. (See page 23.)
(F2) :End playback.
n Video files
Operation is possible using the buttons below.
/
DISPLAY
MODE
:Adjust the volume of the sound.
(F1) :Show the Function menu. (See page 23.)
When the operation panel is displayed, you can
perform the actions below. Select the action with
ENTER
, and execute with
.
Play, stop, rewind, fast-forward, pause, play
previous/next file, rewind about 10 seconds,
fast-forward about 30 seconds.
(F2) :Show/hide guidance.
RETURN
TIPS
(F1) :Show the Function menu. (See page 23.)
(F3) :Rotate the display 90° clockwise. (Single photo
display only)
If you use this function to rotate a photo with
portrait resolution, the image may become
grainier and the rotation setting will not be
saved. When using a portrait photo in a portrait
installation, use a photo that has been rotated in
advance.
RETURN
and
:Show the previous photo file / next photo file
(Single photo display only)
(F2) :Show/hide guidance.
and press
or
.
.
3. Select the folder that contains file you want to delete
ENTER
or
, and press
.
with
1. Press
ENTER
.
RETURN
:End playback.
When a video file is stopped before it finished
ENTER
MODE
to resume the video or press
(F2)
press
to play the video from the beginning.
Playing files
Single photo file is displayed / Playing slideshow
Function menu
DISPLAY
Press
(F1) while each screen is displayed.
ENTER
Select an item with
or
and press
.
Adjust the volume with
or
.
SCREEN SIZE
Changes the screen size. (See page 19.)
TRIMMING trims the top and bottom of a 4:3 video to show it
in full screen mode without changing the aspect ratio.
SLIDE SHOW SETTING (Show the slideshow only)
n Photo files
Photo file is selected
VOLUME SETTING
Adjust the volume with
VOLUME SETTING
or
.
COPY PHOTO
Copy photo files from a USB flash drive to the interna
memory. (See page 21.)
DELETE PHOTO
Delete multiple photo files from the internal memor .
SCREEN SIZE
Set slideshow settings.
PICTURE MODE
Changes the picture mode on the screen. (See page 18.)
n Music files
Include the slideshow BGM selection screen.
VOLUME SETTING
Changes the screen size. (See page 19.)
TRIMMING trims the top and bottom of a 4:3 video to show it
in full screen mode without changing the aspect ratio.
SLIDE SHOW PHOTO SELECT
Adjust the volume with
Show the slideshow photo selection screen. (See page 21.)
SLIDE SHOW SETTING
Cancel all file selections in the selected folde .
SELECT MEDIA
Set slideshow settings.
SORT
or
.
SET ALL AUTO PLAY / SET ALL BGM
Select all files in the selected folde .
RESET ALL AUTO PLAY / RESET ALL BGM
Change the media that is used. (See page 20.)
Sort the files
The slideshow and auto play will play in the sorted order.
SELECT MEDIA
Change the media that is used. (See page 20.)
n Video files
Video file is selected
VOLUME SETTING
Adjust the volume with
Photo file copy / delete screen is displayed
SELECT ALL
Select all files in the selected folde .
CANCEL ALL
Cancel all file selections in the selected folde .
or
.
SET ALL AUTO PLAY
Select all files in the selected folde .
RESET ALL AUTO PLAY
Cancel all file selections in the selected folde .
SELECT MEDIA
Change the media that is used. (See page 20.)
Slideshow photo selection screen is displayed
Playing video file
VOLUME SETTING
Adjust the volume with
or
.
SCREEN SIZE
Changes the screen size. (See page 19.)
TRIMMING trims the top and bottom of a 4:3 video to show it
in full screen mode without changing the aspect ratio.
SLIDE SHOW SETTING
Set slideshow settings.
SELECT SLIDE SHOW BGM
Show the slideshow BGM selection screen. (See page 21.)
SET ALL SLIDE SHOW IMAGE
Select all files in the selected folde .
RESET ALL SLIDE SHOW IMAGE
Cancel all file selections in the selected folde .
VOLUME SETTING
Adjust the volume with
or
.
OPERATION PANEL
Shows the operation panel to let you perform the following
actions. Select the action with
ENTER
and execute
: play, stop, rewind, fast forward, pause, play
with
previous/next file, rewind about 10 seconds, fast forward
about 30 seconds.
PICTURE MODE
Changes the picture mode on the screen. (See page 18.)
WIDE MODE
Changes the screen size. (See page 19.)
23
E
Menu Items
nMenu screen display
Displaying the menu screen
Video and audio adjustment and settings of various functions
are enabled. This section describes how to use the menu
items. See pages 25 to 28 for details of each menu items.
Caution
• Do not turn the main power switch off while the menu items
are being displayed. Doing so may initialize the settings.
nExample of operation
MENU
1 Name of the menu
2 An item being selected (highlighted)
PICTURE
PICTURE MODE
2.Press
or
to select PICTURE, and press
3.Press
or
to select CONTRAST.
[PC]
ENTER
.
MENU
PICTURE
PC
PICTURE MODE
BRIGHT
[ 0] -16
CONTRAST
or
0
[PC]
+16
+40
to adjust the setting.
MENU
PICTURE
PC
PICTURE MODE
BRIGHT
[ 0] -16
CONTRAST
[ +37]
5.Press
MENU
0
to close the menu screen.
TIPS
• The menu will differ depending on the input mode.
E
24
PC
PICTURE MODE
[ +30]
MENU
4.Press
PICTURE
CONTRAST
to display the menu screen.
[ +30]
MENU
BRIGHT
[ 0] -16
(Adjusting CONTRAST in the PICTURE menu)
1.Press
1
[PC]
+16
+40
0
[PC]
+16
+40
2
Menu Items
Menu item details
The menu will differ depending on the input mode and the items that can be set vary depending on the mode.
nPICTURE
PICTURE MODE
Changes the picture mode on the screen. The picture mode on the screen can also be changed using a remote control unit. (See
page 18.)
BRIGHT
Adjusts the backlight brightness.
CONTRAST
Adjusts the difference between the bright and dark portions of the image.
BLACK LEVEL
Adjusts the entire brightness of the video signals.
TINT
Adjusts the hue. Selecting + changes the color towards green, and selecting - changes it towards magenta.
COLORS
Adjusts the color intensity.
SHARPNESS
Adjusts the sharpness of the image.
COLOR ADJUSTMENT
C.M.S.-HUE
Adjusts color tone with 6 colors of R (red), Y (yellow), G (green), C (cyan), B (blue), and M (magenta).
C.M.S.-SATURATION
Adjusts color vividness with 6 colors of R (red), Y (yellow), G (green), C (cyan), B (blue), and M (magenta).
C.M.S.-VALUE
Adjusts color brightness with 6 colors of R (red), Y (yellow), G (green), C (cyan), B (blue), and M (magenta).
WHITE BALANCE
Adjusts from a bluish white (color temperature: 12000K) to a reddish white (color temperature: 3000K). You can also change
the R gain, G gain, and B gain values for each color temperature to perform fine adjustment of the white balance
GAMMA ADJUSTMENT
Adjusts the gradation difference between bright parts and dark parts of video.
25
E
Menu Items
ADVANCED
QUICK SHOOT
ADVANCED(HIGH), ADVANCED(LOW)������������������������� Using interpolation, this shows video that is normally shown at 60
frames/sec at 120 frames/sec for a smoother picture.
However, this may distort the picture of some videos. In this case,
set to STANDARD or OFF.
STANDARD��������������������������������������������������������������������� This makes scenes with fast action clearer and easier to view.
ACTIVE CONTRAST
Automatically adjusts the contrast according to the image.
The adjustment operation may not be smooth depending on the image. In this case select OFF.
RESOLUTION
Adjusts the fineness of the image
MULTI PIXEL DRIVE
Adjusts the gradation to widen the angle of view.
PIXEL DIMMING
Adjusts the contrast of the video.
FILM MODE
Adjusts so the input signal is video at 24 frames per second.
ADVANCED(HIGH), ADVANCED(LOW)���� Play at high-quality for smooth video movement.
STANDARD������������������������������������������������ Play video with each frame shown an equal amount of time.
DIGITAL NR
Reduces block noise caused by digital compression.
MONOCHROME
Sets the video to black & white.
RESET
Resets the values of current picture mode items in PICTURE menu to the factory preset values.
nAUDIO
TREBLE
Adjusts the volume of treble-level sound.
BASS
Adjusts the volume of bass-level sound.
BALANCE
Adjusts the balance of the audio sound between right and left.
BAND EXTENSION
Adjusts so that low range and extended range audio from the speakers can be easily heard.
RESET
Resets the values of the AUDIO menu items to the factory preset values.
E
26
Menu Items
nSETUP
LANGUAGE
Sets the display language for the menu screen.
SLEEP TIMER
When the set time elapses, the monitor automatically enters standby mode. This can be set to up to 23 hours in increments of
one hour.
INPUT SELECT
HDMI SETTING
HDMI CEC LINK�������������������������������������When AUTO is selected, HDMI CEC LINK is enabled and the HDMI input terminal
changes when playback is started on an external device. When OFF is selected,
AUTO POWER ON and AUDIO RETURN CHANNEL cannot be selected.
AUTO POWER ON���������������������������������Sets whether the monitor power turns on when the power of an external device is
turned on.
AUDIO RETURN CHANNEL�������������������When HDMI1 input is used, sets whether the monitor audio is output from
compatible devices via HDMI cable.
POSITION�����������������������������������������������Adjusts the horizontal and vertical position of the image.
HDMI AUTO WIDE
AUTO MODE�������������������������������������Automatically changes the screen size to ZOOM if a black band appears at the top
and bottom of the input video.
HDMI SIGNAL�����������������������������������Sets to ENABLE to have the screen size change automatically according to the screen
size control signal included in the video signal input from the HDMI input terminal.
SCREEN POSITION (D-SUB)
INPUT SIGNAL���������������������������������������When the input signal is 1024 x 768 or 1366 x 768 in PC D-sub, select to match the
resolution.
AUTO SYNC.������������������������������������������When YES is selected, H-POS., V-POS., CLOCK, and PHASE are automatically
adjusted. Use this automatic adjustment when you use the PC D-Sub to display a
PC screen or when you change the setting of the PC. (See page 29.)
SCREEN POSITION�������������������������������Adjusts H-POS. (Position of the longest direction), V-POS. (Position of the shortest
direction), CLOCK, and PHASE. To restore the factory default settings, use RESET.
INPUT SKIP
AUTO������������������������������������������������������Skips when the terminal is not connected.
ON�����������������������������������������������������������Always skips.
OFF���������������������������������������������������������Always enable selection of the input.
Settings in INPUT SKIP are displayed in the input mode selection screen. (SELECTABLE/NOT SELECTABLE)
INPUT LABEL
Changes the display names of input mode.
To enter characters, see page 29.
AUDIO SELECT (HDMI3/D-SUB)
Sets the audio input terminal used when HDMI3 or PC D-sub is input.
HDMI3
HDMI�������������������������������������������������Inputs audio from the HDMI3 input terminal.
HDMI + ANALOG������������������������������Inputs audio from the audio input terminal.
D-SUB
VIDEO�����������������������������������������������Do not use audio.
VIDEO + AUDIO��������������������������������Inputs audio from the audio input terminal.
DIGITAL AUDIO OUTPUT
Sets the audio that is output from the digital audio output (optical) terminal.
When connecting a device that does not support AAC / Dolby Digital to the digital audio output (optical) terminal, set to PCM.
When connecting an AV amplifier or other device that supports AAC / Dolby Digital, set to BIT STREAM.
27
E
Menu Items
COMMUNICATION SETTING
LAN SETUP
Configures the settings to control the monitor from the computer via LAN. (See page 36.
IP CONTROL SETUP
To control the monitor from a computer via LAN, set this to ENABLE and configure the login ID and other settings. (See page 37.
nMONITOR
MONITOR
Selects the installation direction of the monitor.
LANDSCAPE.............Landscape orientation
PORTRAIT................Portrait orientation. MULTIMEDIA (see page 20) always remains in landscape orientation.
* If video is upside down when the monitor is installed in the portrait orientation, you can rotate the video 180 degrees with
PORTRAIT ROTATE (see page 30) in the FUNCTION menu. When this is done, the MONITOR setting cannot be changed.
STANDBY MODE
When STANDARD is selected, startup time from standby mode is reduced. Note, however that, more power will be consumed
in standby mode.
When LOW POWER is selected, current consumption is reduced while the monitor is in standby mode. Note, however, that the
startup time from standby mode becomes longer.
If set to LOW POWER, control via LAN cannot be performed in standby mode.
OFF IF NO OPERATION
Determines whether or not to set the monitor to go into standby mode when there is no operation from the remote control unit,
control commands, or LAN for over 4 hours.
OFF IF NO SIGNAL
Sets whether or not the monitor enters the power standby state when there is no input signal for more than 5 minutes.
nOTHERS
MULTIMEDIA AUTOPLAY
Sets the media used for auto play. (See page 22.)
SOFTWARE VERSION
Shows the software version, etc.
SOFTWARE UPDATE
You can update the software.
SETTING RESET
Resets the settings to the factory default settings.
* Photo files copied to INTERNA MEMORY with MULTIMEDIA will not be erased.
E
28
Menu Items
Character input
Adjustments for PC screen display
For items that require entry of text, press
software keyboard.
Select a character with
enter.
ENTER
to display the
, and press
ENTER
to
• To change the characters entered, select CHAR. SET or
DISPLAY
(F1).
press
• To switch between upper case and lower case, select
ENTER
CAPS and press
.
• To delete characters, select CLEAR or DELETE and press
ENTER
MODE
. You can also perform DELETE by pressing
(F2).
• When you are done entering characters, select DONE and
press ENTER.
SIZE
(F3).
You can also finis by pressing
ENTER
To cancel character entry, select CANCEL and press
.
nAutomatic adjustment
When you use the PC D-sub to display a PC screen, or when
you change the setting of the PC, use the automatic screen
adjustment.
1. Switch the input to D-SUB and display the adjustment
pattern. (See the description below.)
MENU
2. Press
and select AUTO SYNC. of SCREEN POSITION
of INPUT SELECT in the SETUP menu. (See page 27.)
3.Press
ENTER
and select YES.
ENTER
.
4.Press
Wait until automatic adjustment finishes
5.Press MENU to close the menu screen.
TIPS
• If the screen cannot be adjusted properly with one
automatic adjustment, repeat the automatic adjustment two
or three times. Try manual adjustment if necessary.
• When the input signal is 1024 x 768 or 1366 x 768, the
input resolution must be set manually. Select the resolution
with INPUT SIGNAL in SCREEN POSITION of INPUT
SELECT in the SETUP menu. (See page 27.)
nScreen display for adjustment
Before making adjustments in the SCREEN POSITION menu
or PICTURE menu, display an image to brighten the entire
screen. If you are using a Windows PC, use the adjustment
pattern on the supplied CD-ROM.
Opening the adjustment pattern
The following example is performed in Windows 7.
1. Load the supplied CD-ROM into the computer’s CDROM drive.
2. Open [CD Drive] in [Computer].
3. Double-click [Adj_uty.exe].
The adjustment pattern will appear.
Adjust the screen automatically or manually.
4. When adjustment is finished, press the [Esc] on the
computer’s keyboard to quit the adjustment program.
5. Eject the CD-ROM from the CD-ROM drive.
TIPS
• If the display mode on the computer you are using is
65,000 colors, the color levels in the color pattern may
appear differently or grayscale may appear to be colored.
(This is due to the specification of the input signal and is
not a malfunction.)
29
E
Functional Restriction Setting (FUNCTION)
You can restrict operations.
SIZE
down until “F” appears in the left of the
1.Hold
screen.
,
,
,
in that
2. While “F” appears, press
order.
FUNCTION
POWER BUTTON LOCK
RC LOCK
MONITOR LOCK
MENU LOCK
ON SCREEN DISPLAY
LED
PORTRAIT ROTATE
SELECT
ENTER ENTER
[OFF]
[OFF]
[OFF]
[OFF]
[ON 1]
[ON]
[OFF]
RETURN EXIT
3. Select and set the items.
POWER BUTTON LOCK
You can disable the remote control POWER button or
the monitor POWER switch.
OFF����������������������� Enables operation.
ALL LOCK������������� Disables the power buttons on the
monitor and remote control unit.
MONITOR LOCK��� Disables the power switch on the
monitor.
RC LOCK�������������� Disables the power button on the
remote control unit.
RC LOCK
You can disable the remote control buttons other than
power button.
MONITOR LOCK
You can disable the monitor switches other than power
switch.
MENU LOCK
You can disable use of the remote control with
MENU
.
ON SCREEN DISPLAY
Shows/hides the menu, modes and messages.
The FUNCTION screen cannot be hidden.
ON 1�������������� Shows all menus, modes and messages.
ON 2�������������� Hides messages automatically displayed
by the display. Shows messages during
operation.
OFF��������������� Hides all menus, modes and messages.
LED
Specifies whether to light the power LED
PORTRAIT ROTATE
If video is upside down when the monitor is installed in
portrait orientation, you can rotate the video 180 degrees.
This function is for the portrait installation only. Do not
select this function for the landscape installation.
After changing a setting, turn the main power off and
then on.
Rotate the video
180 degrees
4.Press
E
30
RETURN
to return to the normal screen.
Controlling the Monitor with a PC (RS-232C)
You can control this monitor from a PC via RS-232C (COM
port) on the PC.
TIPS
• You cannot use RS-232C and LAN control simultaneously.
PC connection
Connect the COM port on the PC (RS-232C connector) to the
CONTROL terminal (RS-232C input terminal) on the monitor
using the RS-232C conversion cable (supplied) and an RS232 straight cable (commercially available).
Communication conditions
Set the RS-232C communication settings on the PC to match
the monitor’s communication settings as follows:
Baud rate
9600 bps
Stop bit
1 bit
Data length
8 bits
Flow control
None
Parity bit
None
Communication procedure
nCommand format
When a command is sent from the PC to the monitor, the
monitor operates according to the received command and
sends a response message to the PC.
Return code
CONTROL terminal
(RS-232C input terminal)
C1
C3
C4
Command field
(4 prescribed
alphanumerical characters)
PC
To COM port
RS-232 straight cable
(commercially available)
C2
RS-232C conversion
cable (supplied)
P1
P2
P3
P4
Parameter field
(4 character string comprised of:
0-9, +, -, space, ?)
Example: VOLM0030
VOLM 30
* Be sure to input 4 characters for the parameter. Pad with
spaces (“ ”) if necessary.
(“
” is a return code (0DH or 0AH))
Wrong : VOLM30
Right : VOLM 30
When inputting a negative value, specify a numerical value in
three digits.
Example: BLVL-005
If a command has “R” listed for “DIRECTION” in the
“Control command table” on page 33, the current value can be
returned by using “?” as the parameter.
Example:
VOLM ? ? ? ?
←
From PC to monitor (How much
is current volume setting?).
30
←
From monitor to PC (Current
volume setting: 30).
31
E
Controlling the Monitor with a PC (RS-232C)
nResponse code format
When a command has been executed correctly
O
K
Return code
(0DH, 0AH)
A response is returned after a command is executed.
When a command has not been executed
E
R
R
Return code
(0DH, 0AH)
TIPS
• “ERR” is returned when there is no relevant command or
when the command cannot be used in the current state of
the monitor. “ERR” is also returned when return code only
is sent without any command.
• If communication has not been established for reasons
such as a bad connection between the PC and monitor,
nothing is returned (not even ERR).
• “ERR” may be returned when a command cannot be
received correctly due to interference from the surrounding
environment.
Please ensure that the system or software retries the
command if this occurs.
nCommunication interval
• After OK or ERR is returned, you must send the following
commands.
To set a timeout for the command response, specify 10
seconds or longer.
• Provide an interval of 100 ms or more between the
command response and the transmission of the next
command.
VOLM0020
OK
Interval of 100 ms or more
CONT0001
OK
E
32
Controlling the Monitor with a PC (RS-232C)
Control command table
How to read the command table
Command field (See page 31.)
Command:
W When the “Parameter” is set in the parameter field (see page 31), the command functions as described
Direction:
under “Control/Response Contents”.
R The returned value indicated under “Reply” can be obtained by setting “????” or “?
” in the
parameter field (see page 31)
Parameter:
Parameter field (See page 31.)
Response (Returned value)
Reply:
TIPS
• In the power standby state, the only command that is used is POWER CONTROL.
• When STANDBY MODE is LOW POWER, control via LAN is not possible in standby mode.
Power control/Input mode selection
Command
Direction
POWER CONTROL
Function
POWR
WR
Parameter
Reply
Control/Response contents
INPUT MODE SELECTION
ITGD
W
0
IAVD
WR
1
1 HDMI1
2
2 HDMI2
3
3 HDMI3
4
4 HDMI4
5
5 D-SUB
6
6 MULTIMEDIA (USB port/Internal memory)
0
0 Switches to standby mode.
1
1 Returns from standby mode.
Toggle change for input mode.
PICTURE menu
Function
PICTURE MODE
Command
Direction
AVMD
W
Parameter
Reply
Control/Response contents
0
Toggle change for input mode.
1
AV
2
MOVIE
3
GAME
6
DYNAMIC
7
PC
9
sRGB
11
PHOTO
20
R
HIGH RESOLUTION
1 AV
2 MOVIE
3 GAME
6 DYNAMIC
7 PC
9 sRGB
11 PHOTO
20 HIGH RESOLUTION
BRIGHT
VLMP
WR
-16-16
-16-16
CONTRAST
CONT
WR
0-40
0-40
BLACK LEVEL
BLVL
WR
-30-30
-30-30
TINT
TINT
WR
-30-30
-30-30
COLORS
COLR
WR
-30-30
-30-30
SHARPNESS
SHRP
WR
0-20
0-20
33
E
Controlling the Monitor with a PC (RS-232C)
AUDIO menu
Function
BALANCE
Command
Direction
SBAL
WR
Parameter
Reply
-30-30
Control/Response contents
-30-30 Audio output balance (Left 30 to right 30)
SETUP menu
Function
LANGUAGE
SLEEP TIMER
Command
Direction
LANG
WR
OFTM
Parameter
Reply
14
WR
1
1 DEUTSCH
2
2 FRANÇAIS
3
3 ITALIANO
4
4 ESPAÑOL
5
5 РУССКИЙ
6
6
0
0 Cancel
1-23
positioning
Control/Response contents
14 ENGLISH
1-23 Sets the time in hours before the monitor switches to standby mode.
Position of
the longest
direction
HPOS
WR
-88-90
-88-90 Varies depending on the signal.
Position of
the shortest
direction
VPOS
WR
-26-36
-26-36 Varies depending on the signal.
CLOCK
CLCK
WR
-90-90
-90-90 Varies depending on the signal.
PHASE
PHSE
WR
-20-20
-20-20
MONITOR menu
Command
Direction
OFF IF NO OPERATION
Function
NOPO
WR
Parameter
0-1
Reply
0-1
0: OFF, 1: ON
Control/Response contents
OFF IF NO SIGNAL
NSPO
WR
0-1
0-1
0: OFF, 1: ON
Functional Restriction Setting (FUNCTION) menu
Function
BUTTON CONTROL LOCK
E
34
Command
Direction
ALCK
WR
Parameter
0ABC
Reply
Control/Response contents
0ABC A: POWER BUTTON LOCK
0: OFF, 1: ALL LOCK, 2: MONITOR LOCK, 3: RC LOCK
B: RC LOCK
0: OFF, 1: ON
C: MONITOR LOCK
0: OFF, 1: ON
Controlling the Monitor with a PC (RS-232C)
Others
Command
Direction
SCREEN SIZE
Function
WIDE
W
VOLUME
VOLM
WR
Remote control unit
IRCO
W
Parameter
Reply
R
MUTE
MUTE
W
MODEL
MNRD
W
0:Toggle change, 1: NORMAL, 4: ZOOM, 5: WIDE, 8: UNDERSCAN, 9: DOT BY DOT
1, 4-5, 8-9 1: NORMAL, 4: ZOOM, 5: WIDE, 8: UNDERSCAN, 9: DOT BY DOT
0-100
0-100
113
INPUT
114
VOL +
115
VOL -
117
MUTE
11B
DISPLAY / F1
120
Cursor down
139
MODE / F2
152
ENTER
157
Cursor up
1C4
MENU
1D5
SIZE / F3
1D7
Cursor left
1D8
Cursor right
1E4
RETURN
0-2
R
INFORMATION
Control/Response contents
0-1, 4-5, 8-9
0:Toggle change, 1: ON, 2: OFF
1-2 1: ON, 2: OFF
1
Value
TIPS
• Some menu setting items do not have a command. Set with the remote control during installation.
35
E
Controlling the Monitor with a PC (LAN)
Your monitor can be connected to a LAN allowing you to
control it from a PC on the LAN.
The connection requires a commercially available LAN cable
(UTP cable, Category 5, straight through).
Network (LAN)
Settings to connect to a LAN
Set LAN SETUP and IP CONTROL SETUP in
COMMUNICATION SETTING in the SETUP menu. (See page
28.)
The settings depend on the configuratio of your LAN. Ask
your LAN administrator for details.
nLAN SETUP
1. Display the current LAN information.
Hub
LAN terminal
LAN cable (commercially available, straight)
TIPS
• You must assign an IP address to the monitor by following
the procedures in “Settings to connect to a LAN”. (See the
description on the right.)
• To control the monitor via LAN, set IP CONTROL SETUP to
ENABLE. (See page 37.)
• You cannot use RS-232C and LAN control simultaneously.
• When STANDBY MODE is LOW POWER, control is not
possible in the power standby state.
2. If you need to change the setup, select CHANGE or
ENTER
INITIALIZE with
or
, and press
.
CHANGE: Change the LAN setup. See the step 3.
INITIALIZE:Reset the current settings.
3. Set the IP address.
Select YES or NO with
or
, and press
ENTER
YES
Acquire the IP address automatically.
NO
Enter the IP ADDRESS, NETMASK, and GATEWAY with
the software keyboard. (See page 29.)
When NO is selected, YES (auto acquisition of DNS IP
address) cannot be selected in step 5.
ENTER
4. Select NEXT, and press
.
5. Set the IP address of the DNS server.
ENTER
or
, and press
.
Select YES or NO with
YES
Acquire the IP address of the DNS automatically. (Use the
DHCP server function of your network environment.)
NO
Enter the PRIMARY and SECONDARY IP addresses with
the software keyboard. (See page 29.) For the values to
be entered in each field check the specification of your
network environment.
6. Select NEXT, and press
7. Select TEST with
or
ENTER
.
, and press
ENTER
.
8. Check your settings, select COMPLETE with
ENTER
and press
.
E
36
.
or
,
Controlling the Monitor with a PC (LAN)
nIP CONTROL SETUP
1. Set IP control to ENABLE.
and press
Select IP CONTROL SETUP with
or
ENTER
ENTER
. Select CHANGE and press
. Select ENABLE with
ENTER
and press
.
or
2. Configure advanced security settings.
ENTER
and press
.
Select DETAIL SETTING with
or
ENTER
Select CHANGE with
and press
.
or
3. Set the login information.
Enter the LOGIN ID and PASSWORD with the software
keyboard (see page 29).
ENTER
4. Select NEXT and press
.
5. Set the control port.
Enter the CONTROL PORT with the software keyboard (see
page 29).
ENTER
6. Select NEXT and press
.
,
7. Check your settings, select COMPLETE with
or
ENTER
and press
.
Command-based control
You can control the monitor using control commands
(see page 33) via terminal software and other appropriate
applications.
Read the manual for the terminal software for detailed
instructions.
(1) Connect the PC to the monitor.
Use a commercially available LAN cable to connect a PC
to the monitor. (See page 36.)
(2) Send commands to control the monitor.
• The commands used are the same as those for RS232C. Refer to the communication procedure (see
page 31) for operation.
• Usable commands are provided in the control
command table (see page 33).
37
E
Troubleshooting
If you are experiencing any problem with your display, before
calling for service, please review the following troubleshooting
tips.
There is no picture or sound.
• Is the power cord disconnected? (See page 14.)
• Is the main power switch off? (See page 17.)
• Is the monitor in standby mode (the power LED illuminating
in orange)? (See page 17.)
• Make sure correct input mode is selected. (See page 18.)
• If any external equipment is connected, make sure the
equipment is operating (playing back).
Remote control does not work.
• Are the batteries inserted with polarity (+,-) aligned? (See
page 16.)
• Are the batteries exhausted?
• Point the remote control unit toward the monitor’s remote
control sensor. (See page 16.)
• Is ON SCREEN DISPLAY set to OFF or is operation
disabled? (See page 30.)
Sound is heard from only one side.
• Are audio cables connected properly?
• Check the setting of BALANCE for AUDIO menu. (See
page 26.)
There is a picture but no sound.
• Is the sound muted?
• Make sure the volume is not set to minimum.
• Are audio cables connected properly?
• Is the setting of INPUT SELECT on the SETUP menu
correct? (See page 27.)
Unstable video.
• The signal may be incompatible. (See page 41.)
• Try the automatic screen adjustment when the D-SUB are
used. (See page 29.)
The video from the HDMI input terminal does not appear
properly.
• Is the setting for HDMI SETTING of INPUT SELECT on the
SETUP menu correct? (See page 27.)
• Is the HDMI cable HDMI standard compliant? The monitor
will not work with cables that are not standard compliant.
• Is the input signal compatible with this monitor? (See page
41.)
• To show 4K2K video or 1080p video, use a high-speed
HDMI cable.
• If connected to a HDMI1 - 3 input terminal, connect to
the HDMI4 input terminal. The video and audio of some
connected devices may not output correctly because the
HDMI1 - 3 input terminals support 3840 x 2160 (60Hz)
4:4:4 format. If input in this format is not necessary, use the
HDMI4 input terminal. (See page 12.)
The video from PC D-Sub input terminal does not appear
correctly.
• Is the setting for SCREEN POSITION of INPUT SELECT
on the SETUP menu correct? (See page 27.)
• Is the input signal compatible with this monitor? (See page
41.)
E
38
Control buttons do not work.
There is no picture.
• Load noises from outside may be interfering with normal
operation. Turn off the power and turn it on after waiting at
least 5 seconds, and then check the operation.
Power LED flashes red.
• Hardware has a problem. Turn off the monitor and request
repair from your SHARP dealer.
The monitor makes a cracking sound.
• You may occasionally hear a cracking sound from the
monitor. This happens when the cabinet slightly expands
and contracts according to change in temperature. This
does not affect the monitor’s performance.
The Power LED is flashing in red and green alternately.
• When the internal temperature of the monitor rises
excessively, the brightness of the backlight decreases
automatically in order to prevent high-temperature-related
problems. If the internal temperature rises further, the
monitor automatically enters standby mode and the Power
LED blinks red and green alternately.
• Remove the cause of the excessive temperature rise.
- If the monitor enters standby mode due to a rise in
temperature, to return to normal display, turn the power
switch off and then back on again. The monitor, however,
will enter standby mode again if the cause of the
temperature rise is not eliminated. (See page 8.)
- Check whether the monitor is placed at a location where
a quick rise in temperature is likely. Internal temperature
rises quickly if the vents on the monitor are blocked.
- Internal temperature rises quickly if dust accumulates
inside the monitor or around the vents. Remove dust if
possible. Ask SHARP dealer about removing internal dust.
Specifications
nProduct Specifications
Model
LCD component
Max. resolution
Max. colors
Pixel pitch
Viewing angle
Screen active area
Computer input signal
Sync signal
Plug and play
Input terminals
Video
Output terminals
(pixels)
inch (mm)
Audio
Serial (RS-232C)
USB flash driv
Audio
LAN terminal
Speaker output
Internal memory
Power requirement
Operating temperature *1
Operating humidity
Power consumption (Standby mode *2)
Dimensions (excluding protrusions)
inch (mm)
Weight lbs. (kg)
PN-H701
70" Class [69-1/2 inch (176.6cm) diagonal] TFT LCD
3840 x 2160
Approx. 16.77 million colors
0.401 mm (H) × 0.401 mm (V)
176° right/left/up/down (contrast ratio ≥ 10)
60-9/16 x 34-1/16 (1538.9 x 865.6)
HDMI, Analog RGB (0.7 Vp-p) [75 Ω]
Horizontal/vertical separate (TTL: positive/negative)
VESA DDC2B
HDMI x 4
- HDCP1.4 compatible (HDMI1 - HDMI3)
HDCP2.2 compatible (HDMI4)
- ARC compatible (HDMI1)
- MHL compatible (HDMI4)
Mini D-sub 15 pin, 3 rows x 1
3.5 mm mini stereo jack x 1
3.5 mm mini stereo jack x 1
x1
Digital audio output (optical) x 1
3.5 mm mini stereo jack x 1
10 BASE-T/100 BASE-TX
10 W + 10 W
400 MB
AC 100 - 240 V, 3.2 A, 50/60 Hz
32°F to 104°F (0°C to 40°C)
20% to 80% (no condensation)
270 W (0.5 W)
Approx. 61-3/8 (W) x 2-11/16 (D) x 35-3/16 (H) (1559 x 69 x 894)
Approx. 83.8 (38)
*1 Temperature condition may change when using the monitor together with the optional equipments recommended by SHARP. In such cases,
please check the temperature condition specified by the optional equipments
*2 When STANDBY MODE is set to LOW POWER.
As a part of our policy of continuous improvement, SHARP reserves the right to make design and specification changes fo product improvement
without prior notice. The performance specification figures indicated are nominal values of production units There may be some deviations from
these values in individual units.
39
E
Specifications
nDimensional Drawings
Note that the values shown are approximate values.
VESA holes *
2-11/16
[69]
7-7/8
[200]
61-3/8 [1559]
7-7/8
[200]
Unit: inch [mm]
1/2
[13]
15-3/4 [400]
35-3/16 [894]
Opening height (34-5/16 [871.5])
Opening width(60-5/8 [1540.6])
When mounting the monitor, be sure to use a wall-mount bracket that complies with the VESA-compatible mounting method.
SHARP recommends using M6 screws and tighten the screws.
Note that screw hole depth of the monitor is 3/8 inch (10 mm). Loose mounting may cause the product to fall, resulting in
serious personal injuries as well as damage to the product. The screw and hole should come together with over 5/16 inch
(8 mm) length of thread. Use a bracket which has been approved for UL1678 standard, and which can endure at least 4 times
or more the weight of the monitor.
E
40
Specifications
nDDC (plug and play)
The monitor supports the VESA DDC (Display Data Channel) standard.
DDC is a signal standard for plug and play between monitors and computers. Information about resolution and other parameters
is exchanged between the two. This function can be used if the computer supports DDC and it has been configured to detect
plug-and-play monitors.
There are several types of DDC, depending on the communication method used. This monitor supports DDC2B.
nCompatible signal timing (PC)
Screen resolution
VESA
640 × 480
800 × 600
1024 × 768
1280 × 800
1280 × 1024
1400 × 1050
1366 × 768
1920 × 1080
3840 × 2160
Wide
US TEXT
Mac
720 × 400
1920 × 1080
3840 × 2160
Hsync
Vsync
Dot frequency
Digital (HDMI)
Analog (PC D-Sub)
31.5kHz
37.9kHz
37.5kHz
35.1kHz
37.9kHz
48.1kHz
46.9kHz
48.4kHz
56.5kHz
60.0kHz
49.7kHz
64.0kHz
65.3kHz
47.7kHz
67.5kHz
54.0kHz
56.3kHz
67.5kHz
112.5kHz
135.0kHz
31.5kHz
67.5kHz
67.5kHz
60Hz
72Hz
75Hz
56Hz
60Hz
72Hz
75Hz
60Hz
70Hz
75Hz
60Hz
60Hz
60Hz
60Hz
60Hz
24Hz
25Hz
30Hz
50Hz
60Hz
70Hz
60Hz
30Hz
25.175MHz
31.5MHz
31.5MHz
36.0MHz
40.0MHz
50.0MHz
49.5MHz
65.0MHz
75.0MHz
78.75MHz
83.5MHz
108.0MHz
121.75MHz
85.5MHz
148.5MHz
297.0MHz
297.0MHz
297.0MHz
594.0MHz
594.0MHz
28.3MHz
148.5MHz
297.0MHz
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
-
• Depending on the connected PC, images may not be displayed properly even if the compatible signal described above is input.
nCompatible signal timing (AV)
Screen resolution
3840 × 2160p
1920 × 1080p
1920 × 1080i
1280 × 720p
720 × 576p
640 × 480p
720 × 480p
720(1440) × 480i
Frequency
24Hz
25Hz
30Hz
50Hz
60Hz
24Hz
30Hz
50Hz
60Hz
60Hz
30Hz
50Hz
60Hz
50Hz
60Hz
60Hz
60Hz
HDMI
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
PC D-sub
-
41
E
Specifications
nHDMI input terminal
(HDMITM Connector)
No.
E
42
Function
nPC D-sub input
(Mini D-sub 15 pin)
pins
No.
Function
No.
terminal pins
Function
No.
Function
TMDS clock shield
1
Red video signal input
9
+5V
12
TMDS clock-
2
Green video signal input
10
GND
13
CEC
3
Blue video signal input
11
N.C.
N.C.
4
N.C.
12
DDC data
15
SCL
5
GND
13
Hsync signal input
16
SDA
6
GND for red video signal
14
Vsync signal input
DDC/CEC GND
7
GND for green video signal 15
18
+5V
8
GND for blue video signal
19
Hot-plug detection
1
TMDS data 2+
11
2
TMDS data 2 shield
3
TMDS data 2-
4
TMDS data 1+
14
5
TMDS data 1 shield
6
TMDS data 1-
7
TMDS data 0+
17
8
TMDS data 0 shield
9
TMDS data 0-
10
TMDS clock+
DDC clock
Mounting Precautions
(For SHARP dealers and service engineers)
• When installing, removing or moving the monitor, ensure that this is carried out by at least 2 people.
• Be sure to use a wall-mount bracket designed or designated for mounting the monitor.
• This monitor is designed to be installed on a concrete wall or pillar. Reinforced work might be necessary for some materials
such as plaster / thin plastic board / wood before starting installation.
• This monitor and bracket must be installed on a wall which can endure at least 4 times or more the weight of the monitor.
Install by the most suitable method for the material and the structure.
• To attach a VESA-compliant mounting bracket, use M6 screws that are 5/16 inch (8 mm) to 3/8 inch (10 mm) longer than the
thickness of the mounting bracket.
• Do not use an impact driver.
• When moving the monitor, be sure to hold the areas shown in the figure belo . Do not hold the LCD panel. This may cause
product damage, failure, or injury.
• If you need to move the monitor after it has been in use, it may be hot. Turn off the power and make sure it has cooled
sufficiently before moving
• After mounting, please carefully ensure the monitor is secure, and not able to come loose from the wall or mount.
• Do not use any screw holes other than VESA holes for installation.
Learn more about TV & video we offer on our website.
Download PDF
Similar pages