User Manual / AER2100
11/21/16
AER Series
Router
AER2100
User Manual
©2016 Cradlepoint. All Rights Reserved. | +1.855.813.3385 | cradlepoint.com
1
User Manual / AER2100
11/21/16
TABLE OF CONTENTS
INTRODUCTION4
WHAT’S IN THE BOX
4
KEY FEATURES
4
WAN4
LAN4
WIFI4
MANAGEMENT5
VPN AND ROUTING
5
SECURITY5
CLOUD OPTIMIZED IP COMMUNICATIONS
6
SPECIFICATIONS6
ACCESSORIES7
BUSINESS-GRADE MODEM SPECIFICATIONS
7
HARDWARE10
SUPPORT AND WARRANTY
11
LEDS12
QUICK START
13
BASIC SETUP
13
ACCESSING THE ADMINISTRATION PAGES
15
FIRST TIME SETUP WIZARD
15
USING ENTERPRISE CLOUD MANAGER
16
ADMINISTRATION PAGES
17
QUICK LINKS
17
DASHBOARD17
CONNECTION MANAGER
18
WAN INTERFACE PROFILES & PRIORITY
18
STATUS22
INTERNET22
CLIENT LIST
27
TUNNELS27
FIREWALL28
©2016 Cradlepoint. All Rights Reserved. | +1.855.813.3385 | cradlepoint.com
2
User Manual / AER2100
11/21/16
ROUTING29
ETHERNET29
GPS29
LLDP29
SYSTEM LOGS
30
NETWORKING31
LOCAL NETWORKS
31
VLAN INTERFACES
42
TUNNELS42
ROUTING55
QOS65
DNS SERVERS
68
WIFI AS WAN
70
WAN AFFINITY
72
CLIENT DATA USAGE
74
NHRP74
SECURITY76
IDENTITIES76
ZONE FIREWALL
77
CONTENT FILTERING
82
THREAT MANAGEMENT
85
CERTIFICATE MANAGEMENT
87
SYSTEM90
ADMINISTRATION90
ENTERPRISE CLOUD MANAGER
96
DEVICE ALERTS
96
SERIAL REDIRECTOR
98
SNMP CONFIGURATION
98
SYSTEM CONTROL
100
DIAGNOSTICS102
SETUP WIZARDS
103
APPENDIX106
SAFETY, REGULATORY, AND WARRANTY GUIDE
106
ROUTER COMMUNICATION/DATA USAGE
109
©2016 Cradlepoint. All Rights Reserved. | +1.855.813.3385 | cradlepoint.com
3
User Manual / AER2100
11/21/16
INTRODUCTION
WHAT’S IN THE BOX
•
•
•
•
•
•
•
AER 2100 with integrated MC400 4G LTE modem
External 3G/4G mobile broadband modem antennas (2) (SMA) w/ multiplexing for GPS; finger tighten only
External dual-band high-gain WiFi antennas (3) reverse SMA (5 dBi, 2.4 GHz, 5 dBi 5 GHz, VSWR 2); finger tighten
only
12 V / 3 A AC/DC power adapter
Multipurpose Retaining Tool
Ethernet cable
Quick Start Guide with warranty information
KEY FEATURES
WAN
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
LP6: LTE Advanced LTE/HSPA+ (SIM-based Auto-Carrier Selection for all North American carriers and European
operators)
LP5: Cat 6 LTE Advanced for operators in Asia Pacific (SIM-based Auto-Carrier selection)
LP4 Modems (accessory option only): LTE/DC-HSPA+ for AT&T, Verizon, T-Mobile and Canadian carriers (SIM-based
Auto-Carrier Selection, dual-modem capable)
LPE: 4G LTE/HSPA+/EVDO (multi-carrier, North America)
LP3: 4G LTE/HSPA+ (Europe, EMEA, and Australia/New Zealand)
Dual integrated modem option
Dual SIM slot in each modem
Most models include support for active GPS
WiFi as WAN
Failover/Failback
Load Balancing
Advance Modem Failure Check
WAN Port Speed Control
WAN/LAN Affinity
IP Passthrough
Standby
LAN
•
•
•
•
•
•
•
•
•
VLAN 802.1Q
DHCP Server, Client, Relay
DNS and DNS Proxy
DynDNS
UPnP
DMZ
Multicast/Multicast Proxy
QoS (DSCP and Priority Queuing)
MAC Address Filtering
WIFI
•
Dual-Band Dual-Concurrent (3×3 MIMO)
©2016 Cradlepoint. All Rights Reserved. | +1.855.813.3385 | cradlepoint.com
4
User Manual / AER2100
•
•
•
•
•
11/21/16
802.11x (a, b, g, n, ac)
Up to 256 connected devices (128 per channel – 2.4 GHz and 5 GHz)
WPA2 Enterprise (WiFi)
Hotspot/Captive Portal
SSID-based Priority
MANAGEMENT
•
•
•
•
•
•
•
•
•
•
Cradlepoint Enterprise Cloud Manager²
Web UI, API, CLI
GPS Location
Data Usage Alerts (router and per client)
Advanced Troubleshooting (support)
Auto APN Recovery
Device Alerts
SNMP
SMS control
Serial Redirector
VPN AND ROUTING
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
IPsec Tunnel – up to 20 concurrent sessions
OpenVPN (SSL VPN)¹
L2TP¹
GRE Tunnel
VTI Tunnel support
OSPF/BGP/RIP¹
Route Filters (Access Control Lists, Prefix Filters, Route Maps, Communities for BGP)
Per-Interface Routing
Routing Rules
Policy-based Routing
NAT-less Routing
Virtual Server/Port Forwarding
NEMO/DMNR¹
IPv6
VRRP¹
STP¹
NHRP¹
CP Secure VPN compatible
SECURITY
•
•
•
•
•
•
•
•
•
•
•
RADIUS and TACACS+ support*
802.1x authentication for Ethernet
Zscaler integration¹
Certificate support
ALGs
MAC Address Filtering
Advanced Security Mode (local user management only)
Per-Client Web Filtering
IP Filtering
Content Filtering (basic)
Website Filtering
©2016 Cradlepoint. All Rights Reserved. | +1.855.813.3385 | cradlepoint.com
5
User Manual / AER2100
11/21/16
* - Native support for authentication. Authorization and accounting support through hotspot/captive portal services.
CLOUD OPTIMIZED IP COMMUNICATIONS
•
•
•
•
•
•
•
•
Automated WAN Failover/Failback support
WAN Affinity and QoS allow prioritization of VoIP services
Advanced VPN connectivity options to HQ
SIP ALG and NAT to allow VoIP and UC communications to traverse firewall
MAC Address Filtering
802.1p/q for LAN QoS segmentation and treatment of VoIP on LAN
Private Network support (wired and 4G WAN)
Cloud-based management²
1 – Requires an ECM PRIME subscription or an Extended Enterprise License
2 – Enterprise Cloud Manager requires a subscription
SPECIFICATIONS
WAN:
• Integrated LP6 Category 6 LTE Advanced LTE modem (with DC-HSPA+ failover), LP5 Category 6 LTE Advanced LTE
modem (with DC-HSPA+ failover), LPE 4G LTE modem (with HSPA+/ EVDO/3G and 2G failover), or LP3 4G LTE modem
(with HSPA+ and 2G failover)
• One modem included, dual-modem option
• Five 10/100/1000 Ethernet ports (cable/DSL/T1/satellite/Metro Ethernet; WAN/LAN switchable)
• WiFi (as WAN; Metro WiFi) 3x3 MIMO 2.4 GHz or 5 GHz (802.11 a/b/g/n/ac)
LAN:
• Dual-band dual-concurrent WiFi (802.11 a/b/g/n/ac)
• Five 10/100/1000 Ethernet ports (WAN/LAN switchable)
• Serial console support w/ USB-to-serial adapter
TEMPERATURE:
• 0 °C to 50 °C (32 °F to 122 °F) operating
• -20 °C to 70 °C (-4 °F to 158 °F) storage
HUMIDITY (non-condensing):
• 10% to 85% operating
• 5% to 90% storage
MEMORY: 256 MB DRAM; 16 MB SPI Flash; 256 MB NAND Flash
SIZE:
• 10.25 × 8.5 × 1.75 in (260 × 214 × 45 mm)
WEIGHT: 6 lb
CERTIFICATIONS: FCC, WiFi Alliance, CE, IC, carrier certifications
LAN TO WAN: 940 Mbps
WAN TO LAN: 940 Mbps
STATEFUL THROUGHPUT: 940 Mbps
WIFI POWER (FCC):
• 2.4 GHz band: 24.47 dBm
• Lower 5 GHz band: 16.9 dBm
• Upper 5 GHz band: 27.77 dBm
©2016 Cradlepoint. All Rights Reserved. | +1.855.813.3385 | cradlepoint.com
6
User Manual / AER2100
11/21/16
POWER CONSUMPTION (Typical)
AER2100
• Idle: 8.0 W
• Single Modem: 13.2 W
• Dual Modem: 16.0 W
ACCESSORIES
•
•
•
•
•
•
•
•
•
•
•
•
•
Second integrated 4G LTE modem
• MC400LP6 (North America or EU)
• MC400LP5 (Asia Pacific)
• MC400LP4 (AT&T, Verizon, T-Mobile and Canada)
• MC400LPE-VZ (Verizon)
• MC400LPE-AT (AT&T)
• MC400LPE-SP (Sprint)
• MC400LPE-GN (generic – for use on T-Mobile in the U.S. and Rogers, Bell, & TELUS in Canada)
• MC400LP3-EU (Europe)
Standard rack mount with modem and WiFi cables (Part # 170629-000)
12V 3A wall power adapter (Part # 170623-000)
12V 4A wall power adapter (Part # 170624-000)
700 MHz – 2700 MHz Wide Band Directional Antenna (Yagi/Log- Periodic) Part #: 170588-000
12” Mag-Mount Antenna with SMA Male Connector Part #: 170605-000
4” Mini Mag-Mount Antenna with SMA Male Connector Part #: 170606-000
2.4/5 GHz Dual-band Dual-concurrent WiFi Antenna Part #: 170628-000 (WiFi models only)
Universal 3G/4G/LTE Modem Antenna Part #: 170649-000
GPS Screw-Mount Antenna Part #: 170651-000
GPS Mag-Mount Antenna Part #: 170652-000
Multi-Band Omni-Directional Antenna Part #: 170668-000
Indoor/Outdoor Panel Patch Part #: 170669-000
BUSINESS-GRADE MODEM SPECIFICATIONS
AER2100 LP6 models include an integrated LTE Advanced Category 6 4G LTE modem. The LP6 modems support SIMBased Auto-Carrier selection so there is only one model for all of North America. Simply insert the SIM and wait for
the router to automatically detect the SIM and establish a connection.
The LTE bands certified for each carrier are listed below.
AER2100LP6-NA, AER2100LP6-EU, AER2100LP6-UK
• Technology: LTE Advanced, DC-HSPA+
• Downlink Rates: LTE 300 Mbps, DC-HSPA+ 42.2 Mbps
• Uplink Rates: LTE 50 Mbps, DC-HSPA+ 5.76 Mbps
• Frequency Bands:
• LTE Bands 1–5, 7, 8, 12, 13, 17, 20, 25, 26, 29, 30, 41
©2016 Cradlepoint. All Rights Reserved. | +1.855.813.3385 | cradlepoint.com
7
User Manual / AER2100
•
•
•
•
•
•
•
11/21/16
• Verizon: 2, 4, 5, 13 (XLTE support w/carrier aggregation)
• AT&T: 2, 4, 5, 12/17, 29, 30
• Sprint: 25, 26, 41 (LTE Plus Support)
• T-Mobile: 2, 4, 12 (T-Mobile Wideband LTE Support)
• Generic: all
Carrier Aggregation:
• 1+ 8
• 2+ 2/5/12 (17 w/MFBI)/13/29
• 3+ 7/20
• 4+ 4/5/12 (17 w/MFBI)/13/29
• 5+ 2/4/30
• 7+ 3/7/20
• 8+ 1
• 12 (17 w/MFBI) + 2/4/30
• 13+ 2/4
• 20+ 3/7
• 30+ 5/12 (17 w/MFBI)
• 41+ 41
Fallback: WCDMA/DC-HSPA+ (42/5.76 Mbps): Bands 1, 2, 3, 4, 5, 8
Power: LTE: 23 dBm ± 1; DC-HSPA+: 23 dBm ± 1
Antennas: two SMA male (plug), finger tighten only (maximum torque spec is 7 kgf/cm2)
GPS: active GPS support
SMS: SMS support
Industry Standards & Certs: CE, FCC, GCF-CC, IC, PTCRB, AT&T, Sprint, Verizon
AER2100LP5 models The LP5 modems support SIM-Based Auto-Carrier selection. Simply insert the SIM and wait for
the router to automatically detect the SIM and establish a connection.
AER2100LP5-AU
• Technology: FDD/TDD (Category 6) LTE Avanced, DC-HSPA+
• Downlink Rates: LTE 300 Mbps, DC-HSPA+ 42.2 Mbps
• Uplink Rates: LTE 50 Mbps, DC-HSPA+ 5.76 Mbps
• Frequency Bands:
• LTE Bands: 1, 3, 5, 7, 8, 11, 18, 19, 21, 28, 38, 39, 40, 41
• TD-SCDMA 39
• Carrier Aggregation:
• 1+ (8, 18, 19, 21)
• 3+ (5, 7, 19, 28)
• 7+ (5, 7, 28)
• 19+ 21
• 38+ 38
• 39+ 39
• 40+ 40
• 41+ 41
• Fallback: WCDMA/DC-HSPA+ (42/5.76 Mbps): Bands 1, 5, 6, 8, 9, 19
• Power: LTE: 23 dBm ± 1; DC-HSPA+: 23 dBm ± 1
• Antennas: two SMA male (plug), finger tighten only (maximum torque spec is 7 kgf/cm2)
• GPS: active GPS support
• SMS: SMS support
• Industry Standards & Certs: CE, GCF-CC, RC Australia, others pending
• Modem Part Number: MC400LP5
©2016 Cradlepoint. All Rights Reserved. | +1.855.813.3385 | cradlepoint.com
8
User Manual / AER2100
11/21/16
AER2100 LPE/LP3 models include an integrated 4G LTE modem (MC400); specific model names include a specific
modem (e.g., the AER 2100LPE-VZ includes an MC400LPE-VZ modem for Verizon).
Please note that LPE models are flexible and support bands for multiple cellular providers; however, only the
frequency bands in bold below are supported by the listed provider.
AER 2100LPE-VZ – 4G LTE/HSPA+/EVDO for Verizon
• Technology: LTE, HSPA+, EVDO Rev A
• Downlink Rates: LTE 100 Mbps, HSPA+ 21.1 Mbps, EVDO 3.1 Mbps (theoretical)
• Uplink Rates: LTE 50 Mbps, HSPA+ 5.76 Mbps, EVDO 1.8 Mbps (theoretical)
• Frequency Bands:
• LTE Band 2 (1900 MHz), Band 4 – AWS (1700/2100 MHz), Band 5 (850 MHz), Band 13 (700 MHz), Band 17 (700
MHz), Band 25 (1900 MHz)
• HSPA+/UMTS (850/900/1900/2100 MHz, AWS)
• GSM/GPRS/EDGE (850/900/1800/1900 MHz)
• CDMA EVDO Rev A/1xRTT (800/1900 MHz)
• Power: LTE: 23 dBm ± 1; HSPA+: 23 dBm ± 1; EVDO: 24 dBm +0.5/-1 (typical conducted)
• Antennas: two SMA male (plug), 1 dBi (LTE), 2 dBi (Cellular/PCS) gain; finger tighten only (maximum torque spec is
7 kgf/cm2)
• GPS: active GPS support
• Industry Standards & Certs: FCC, Verizon
• Modem Part Number: MC400LPE
AER 2100LPE-AT – 4G LTE/HSPA+/EVDO for AT&T
• Technology: LTE, HSPA+, EVDO Rev A
• Downlink Rates: LTE 100 Mbps, HSPA+ 21.1 Mbps, EVDO 3.1 Mbps (theoretical)
• Uplink Rates: LTE 50 Mbps, HSPA+ 5.76 Mbps, EVDO 1.8 Mbps (theoretical)
• Frequency Bands:
• LTE Band 2 (1900 MHz), Band 4 – AWS (1700/2100 MHz), Band 5 (850 MHz), Band 13 (700 MHz), Band 17 (700
MHz), Band 25 (1900 MHz)
• HSPA+/UMTS (850/900/1900/2100 MHz, AWS)
• GSM/GPRS/EDGE (850/900/1800/1900 MHz)
• CDMA EVDO Rev A/1xRTT (800/1900 MHz)
• Power: LTE: 23 dBm ± 1; HSPA+: 23 dBm ± 1; EVDO: 24 dBm +0.5/-1 (typical conducted)
• Antennas: two SMA male (plug), 1 dBi (LTE), 2 dBi (Cellular/PCS) gain; finger tighten only (maximum torque spec is
7 kgf/cm2)
• GPS: active GPS support
• Industry Standards & Certs: PTCRB, FCC, IC, AT&T
• Modem Part Number: MC400LPE
AER 2100LPE-SP – 4G LTE/HSPA+/EVDO for Sprint
• Technology: LTE, HSPA+, EVDO Rev A
• Downlink Rates: LTE 100 Mbps, HSPA+ 21.1 Mbps, EVDO 3.1 Mbps (theoretical)
• Uplink Rates: LTE 50 Mbps, HSPA+ 5.76 Mbps, EVDO 1.8 Mbps (theoretical)
• Frequency Bands:
• LTE Band 2 (1900 MHz), Band 4 – AWS (1700/2100 MHz), Band 5 (850 MHz), Band 13 (700 MHz), Band 17 (700
MHz), Band 25 (1900 MHz)
• HSPA+/UMTS (850/900/1900/2100 MHz, AWS)
• GSM/GPRS/EDGE (850/900/1800/1900 MHz)
• CDMA EVDO Rev A/1xRTT (800/1900 MHz)
• Power: LTE: 23 dBm ± 1; HSPA+: 23 dBm ± 1; EVDO: 24 dBm +0.5/-1 (typical conducted)
©2016 Cradlepoint. All Rights Reserved. | +1.855.813.3385 | cradlepoint.com
9
User Manual / AER2100
•
•
•
•
11/21/16
Antennas: two SMA male (plug), 1 dBi (LTE), 2 dBi (Cellular/PCS) gain; finger tighten only (maximum torque spec is
7 kgf/cm2)
GPS: active GPS support
Industry Standards & Certs: FCC, Sprint
Modem Part Number: MC400LPE
AER 2100LP3-EU (2100LP3-UK*) – 4G LTE/HSPA+ for Europe (United Kingdom)
• Technology: LTE, HSPA+
• Downlink Rates: LTE 100 Mbps, HSPA+ 21.1 Mbps (theoretical)
• Uplink Rates: LTE 50 Mbps, HSPA+ 5.76 Mbps (theoretical)
• Frequency Bands:
• LTE Band 1 (2100 MHz), Band 3 (1800 MHz), Band 7 (2600 MHz), Band 8 (900 MHz), Band 20 (800 MHz)
• HSPA+/UMTS (800/850/900/1900/2100 MHz)
• GSM/GPRS/EDGE Quad-Band (850/900/1800/1900 MHz)
• Power: LTE Band 1/3/8/20: 23 dBm ± 1; LTE Band 7–22: dBm ± 1; HSPA+: 23 dBm ± 1 (typical conducted)
• Antennas: two SMA male (plug), 1 dBi (LTE), 2 dBi (Cellular/PCS) gain; finger tighten only (maximum torque spec is
7 kgf/cm2)
• GPS: active GPS support
• Industry Standards & Certs: CE, GCF-CC
• Modem Part Number: MC400LP3
*The 2100LP3-EU and 2100LP3-UK models are equivalent except for the line cord.
AER 2100LPE-GN – 4G LTE/HSPA+/EVDO (generic – for use on T-Mobile and US Cellular in the U.S. and Rogers, Bell, &
TELUS in Canada)
• Technology: LTE, HSPA+, EVDO Rev A
• Downlink Rates: LTE 100 Mbps, HSPA+ 21.1 Mbps, EVDO 3.1 Mbps (theoretical)
• Uplink Rates: LTE 50 Mbps, HSPA+ 5.76 Mbps, EVDO 1.8 Mbps (theoretical)
• Frequency Bands:
• LTE Band 2 (1900 MHz), Band 4 (AWS), Band 5 (850 MHz), Band 13 (700 MHz), Band 17 (700 MHz), Band 25
(1900 MHz)
• HSPA+/UMTS (850/900/1900/2100 MHz, AWS)
• GSM/GPRS/EDGE (850/900/1800/1900 MHz)
• CDMA EVDO Rev A/1xRTT (800/1900 MHz)
• Power: LTE: 23 dBm ± 1; HSPA+: 23 dBm ± 1; EVDO: 24 dBm +0.5/-1 (typical conducted)
• Antennas: two SMA male (plug), 1 dBi (LTE), 2 dBi (Cellular/PCS) gain; finger tighten only (maximum torque spec is
7 kgf/cm2)
• GPS: active GPS support
• Industry Standards & Certs: PTCRB, FCC, IC
• Modem Part Number: MC400LPE
©2016 Cradlepoint. All Rights Reserved. | +1.855.813.3385 | cradlepoint.com
10
User Manual / AER2100
11/21/16
HARDWARE
LEDs
USB 2.0
Port
WiFi Antenna Connector
(Reverse SMA)
WiFi Antenna Connector
(Reverse SMA)
LEDs
Reset Button
10/100/1000
Ethernet Port
(Configurable:
LAN or WAN
Default: WAN)
10/100/1000 Ethernet
Ports (Configurable:
LAN or WAN
Default: LAN)
Power Switch
and Port
USB 2.0
Port
Ground
Screw
Lock
Slot
SUPPORT AND WARRANTY
CradleCare Support available with technical support, software upgrades, and advanced hardware exchange – 1-, 3-, and
5-year options.
One-year limited hardware warranty available in the US and Canada; two-year limited hardware warranty for
integrated EU products when purchased from an authorized EU distributor – extend warranty to 2, 3, or 5 years.
©2016 Cradlepoint. All Rights Reserved. | +1.855.813.3385 | cradlepoint.com
11
User Manual / AER2100
11/21/16
LEDS
POWER The Cradlepoint AER2100 must be powered using an approved 12 V DC power source.
•
•
•
WAN
ETHERNET WAN Indicates information about a data source connected to the Ethernet WAN port.
•
2.4GHz
5GHz
EC
Green = Powered ON.
No Light = Not receiving power. Check the power switch and the power source connection.
Flashing Amber = Attention. Open the administration pages and check the router status.
Blue = Connected to an active Ethernet WAN interface.
WiFi BROADCAST These two LEDs indicate activity on the WiFi broadcast for both the 2.4
GHz and 5 GHz bands.
•
•
2.4 GHz (green) = 2.4 GHz WiFi is on and operating normally.
5 GHz (blue) = 5 GHz WiFi is on and operating normally.
SIGNAL STRENGTH Blue LED bars indicate the active modem’s signal strength.
•
•
4 Solid Bars = Strongest signal.
1 Blinking Bar = Weakest signal. (A blinking bar indicates half of a bar.)
REMOVABLE MODEM Indicates the status of removable modem(s).
EXTERNAL USB MODEM Indicates the status of external USB modem.
Both internal and external USB modems have the following LED indicators:
•
•
•
•
•
Green = Modem has established an active connection.
Blinking Green = Modem is connecting.
Amber = Modem is not active.
Blinking Amber = Data connection error. No modem connection possible.
Blinking Red = Modem is in the process of resetting.
ADDITIONAL LED INDICATIONS
•
•
Several different LEDs flash when the factory reset button is detected.
Two of the modem LEDs blink red in unison for 10 seconds when there is an error during firmware
upgrade.
©2016 Cradlepoint. All Rights Reserved. | +1.855.813.3385 | cradlepoint.com
12
User Manual / AER2100
11/21/16
QUICK START
BASIC SETUP
1. Insert an activated SIM
A wireless broadband data plan must be added to your Cradlepoint AER2100. Wireless broadband data plans are
available from wireless carriers such as Verizon, AT&T, Sprint, EE, and Vodafone. The SIM must be provisioned
with the carrier. Contact your carrier for details about selecting a data plan and about the process for
provisioning your SIM.
Once you have an activated SIM, insert it into the integrated modem. Insert the SIM card into the slot marked
SIM 1 (use the other slot, SIM 2, for a secondary/backup SIM).
Insert the card with the notch-end first and the gold contacts facing down – it will click into place.
Notch-end goes in first
Gold contacts face down
2. Insert the removable modem
Follow these steps to insert the removable modem(s):
1. Remove the left side panel cover from the router. Use a Phillips screwdriver to remove the screws, and use
the Multipurpose Retaining Tool (included in the router package) to remove the cover.
2. Slide the modem into the side of the router (left slot first). The protruding section of the modem fits into
the groove.
3. Reattach the modem cover. If desired, use a Phillips screwdriver to secure modem door screws to bottom
side of the router near the front.
©2016 Cradlepoint. All Rights Reserved. | +1.855.813.3385 | cradlepoint.com
13
User Manual / AER2100
11/21/16
3. Attach the WiFi and modem antennas
Attach the three WiFi antennas (included) and two modem antennas to the connectors. Antennas are jointed,
which enables you to position them for optimal signal. To attach, hold the antenna straight and twist the base
of the antenna to connect, folding the joint if needed. NOTE: Ensure that the router antennas are not near metal
or other RF reflective surfaces.
Examples of suggested antenna orientations:
Desk Mount
Wall Mount
4. Connect the power source
Plug the provided power supply (12V DC wall adapter) into an electrical outlet. Then connect the power supply to
the router.
Ensure power is switched on:
O = OFF
– = ON
Power Switch
Power
Supply Port
When you set the power switch to the ON ( – ) position, watch for the power LED to illuminate.
5. Connect to a computer or other network equipment
Connect wirelessly to the WiFi broadcast or with an Ethernet cable connected to your computer and then
plugged into one of the Ethernet LAN ports (numbered 1–4). The default WiFi network name is “2100-xxx”,
where “xxx” is the last three characters of your router’s MAC address (this is the SSID on the product label). To
connect to the WiFi, you will need to input the DEFAULT PASSWORD when prompted. The DEFAULT PASSWORD is
provided on the product label found on the bottom of your router.
NOTE: The product label below is an example only: your DEFAULT PASSWORD and SSID will be unique.
©2016 Cradlepoint. All Rights Reserved. | +1.855.813.3385 | cradlepoint.com
14
User Manual / AER2100
11/21/16
ACCESSING THE ADMINISTRATION PAGES
Once you are connected, open the Cradlepoint AER2100’s GUI-based administration pages to make configuration
changes to your router.
1. Open a browser window and type “cp/” or “192.168.0.1” in the address bar. Press ENTER/RETURN.
2. When prompted for your password, type the eight character DEFAULT PASSWORD found on the product
label.
It’s possible – and more efficient – to do all your configuration changes through Cradlepoint Enterprise Cloud
Manager (ECM) without logging into the local administration pages. Set up a group of routers and set the
configuration for all of them at once. See below for more information about ECM.
FIRST TIME SETUP WIZARD
When you log in for the first time, you will be automatically directed to the FIRST TIME SETUP WIZARD, which
will walk you through the steps to customize your Cradlepoint AER2100. You have the ability to configure any of
the following:
•
•
•
•
•
•
•
Administrator Password
Time Zone
WiFi Network Name
Security Mode
Access Point Name (APN) for SIM-based modems
Modem Authentication
Failure Check
If you are currently using the router’s WiFi network, you will need to reconnect your devices to the network
using the newly established wireless network name and password.
NOTE: To return to the First Time Setup Wizard after your initial login, select SYSTEM from the navigation bar,
expand Setup Wizard, and select First Time Setup.
©2016 Cradlepoint. All Rights Reserved. | +1.855.813.3385 | cradlepoint.com
15
User Manual / AER2100
11/21/16
USING ENTERPRISE CLOUD MANAGER
Rapidly deploy and dynamically manage networks at geographically distributed stores and branch locations with
Enterprise Cloud Manager, Cradlepoint’s next generation management and application platform. Enterprise Cloud
Manager (ECM) integrates cloud management with your Cradlepoint devices to improve productivity, increase
reliability, reduce costs, and enhance the intelligence of your network and business operations.
Click here to sign up for a free 30-day ECM trial.
Depending on your ordering process, your devices may have already been bulk-loaded into ECM. If so, simply
log in at cradlepointecm.com using your ECM credentials and begin managing your devices seamlessly from the
cloud.
If your device has not yet been loaded into your ECM account, you need to register. Log into the device
administration pages and select Enterprise Cloud Manager from the SYSTEM menu. Enter your ECM username
and password, and click on “Register”.
Once you have registered your device, go to cradlepointecm.com and log in using your ECM credentials.
For more information about how to use Cradlepoint Enterprise Cloud Manager, see the following:
•
•
Getting Started
ECM on the Knowledge Base
©2016 Cradlepoint. All Rights Reserved. | +1.855.813.3385 | cradlepoint.com
16
User Manual / AER2100
11/21/16
ADMINISTRATION PAGES
Quick Links
Dashboard
Connection Manager
Status
Networking
Security
System
QUICK LINKS
Quick Links allows you to bookmark your most commonly-used settings. Simply click on the bookmark icon ( )
to add an item to your Quick Links menu. To remove an item from your Quick Links menu, select the item and
click on the remove bookmark icon ( ).
Quick Links Menu
Add Quick Link
Delete Quick Link
DASHBOARD
The Dashboard is a centralized location for basic
information about the status of your router. The areas
include:
•
•
•
•
•
•
Device Information
Ethernet WAN*
Modems*
WWAN*
Ethernet LAN*
WiFi LAN*
*-To quickly edit settings for any of these areas, click on
the pencil icon ( ) in the top-right of the desired dialog
box.
You may return to the Dashboard at any time by clicking
on DASHBOARD from the left menu or by clicking on the
Cradlepoint logo at the top-left of the screen.
©2016 Cradlepoint. All Rights Reserved. | +1.855.813.3385 | cradlepoint.com
17
User Manual / AER2100
11/21/16
CONNECTION MANAGER
The router can establish an uplink via Ethernet, WiFi as WAN, or 3G/4G modems (removable or external USB). If the
primary WAN connection fails, the router will automatically attempt to bring up a new link on another device: this
feature is called failover. If Load Balance is enabled, multiple WAN devices may establish a link concurrently.
WAN INTERFACE PROFILES & PRIORITY
This is a list of the available interfaces used to access the Internet. You can enable, stop, or start devices from this
section. Drag the priority icon ( ) up or down to set the interface the router uses by default and the order that it
allows failover.
Availability Key
Enable
Load Balance
WAN Verify
Standby
On Demand
Failback
Data Usage
STANDBY
Standby is used to decrease failover time from one WAN interface to another. When Standby is enabled for a WAN
profile or interface, the relevant interfaces are kept in a connected-but-idle (minimal, non-routed traffic) state. When
the current WAN connection is disrupted, the traffic will failover to the next priority WAN. If that interface is on
Standby, the connection is already established and failover will take much less time.
Note that the current connected interface(s) is/are indicated by a green connection state. For interfaces on Standby,
the interface is indicated by a yellow connection state. If the interface is indicated in red, the interface is not currently
connected or in Standby.
Standby is used to enable faster failover times only. If you want to manage traffic to a specific WAN interface, you
will need to use WAN Affinity. If WAN Affinity is enabled for a particular profile or interface, do not enable Standby for
that profile or interface as the failover results may vary and be unexpected.
©2016 Cradlepoint. All Rights Reserved. | +1.855.813.3385 | cradlepoint.com
18
User Manual / AER2100
11/21/16
LOAD BALANCE
To enable Load Balancing, select the check box for each desired device. If this is enabled, the router will use multiple
WAN interfaces to increase the data transfer throughput by using any connected WAN interface consecutively.
Selecting Load Balance will automatically start the WAN interface and add it to the pool of WAN interfaces to use
for data transfer. Turning off Load Balance for an active WAN interface may require the user to restart any current
browsing session.
From WAN Management, select the Load Balance Algorithm from
the following dropdown options:
•
•
•
•
Round-Robin: Evenly distribute each session to the available
WAN connections.
Rate: Distribute load based on the current upload and
download rates. A WAN device’s upload and download
bandwidth values can be set in Internet > Connection
Manager.
Spillover: This was the default algorithm in older (version
3) firmware. Load is always given to devices with the most
available bandwidth. The estimated bandwidth rate is based on a combination of the upload and download
configuration values and the observed capabilities of the device.
Data Usage: This mode works in concert with the Data Usage feature (Internet > Data Usage).
The router will make a best effort to keep data usage between interfaces at a similar percentage of the assigned data
cap in the data usage rule for each interface, rather than distributing sessions based solely on bandwidth. For proper
functioning you need to create data usage rules for each WAN device you will be load balancing. Make certain to select
the “Use with Load Balancing” checkbox in the data usage rule editor.
ON DEMAND
Typically, modem connections are not always on.
When the On Demand mode is selected a connection
to the Internet is made as needed. When On
Demand is not selected a connection to the Internet
is always maintained.
WAN VERIFY
If this is enabled, the router will check that the highest priority active WAN interface can get to the Internet even if
the WAN connection is not actively being used. If the interface goes down, the router will switch to the next highest
priority interface available. If this is not selected, the router will still failover to the next highest priority interface but
only after the user has attempted to get out to the Internet and failed.
Idle Check Interval: The amount of time between each check. (Default: 30 seconds. Range: 10-3600 seconds.)
Monitor while connected: (Default: Off) Select from the following dropdown options:
•
Passive DNS (modem only): The router will take no action until data is detected that is destined for the WAN.
©2016 Cradlepoint. All Rights Reserved. | +1.855.813.3385 | cradlepoint.com
19
User Manual / AER2100
11/21/16
When this data is detected, the data will be
sent and the router will check for received
data for two seconds. If no data is received the
router behaves as described below under Active
DNS.
•
Active DNS (modem only): A DNS request will be
sent to the DNS servers. If no data is received,
the DNS request will be retried four times at
five-second intervals. (The first two requests
will be directed at the Primary DNS server and
the second two requests will be directed at
the Secondary DNS server.) If still no data is
received, the device will be disconnected and
failover will occur.
•
Active Ping: A ping request will be sent to the Ping Target. If no data is received, the ping request will be retried
four times at five-second intervals. If still no data is received, the device will be disconnected and failover will
occur. When “Active Ping” is selected, the next line gives an estimate of data usage in this form: “Active Ping
could use as much as 9.3 MB of data per month.” This amount depends on the Idle Check Interval.
•
Off: Once the link is established the router takes no action to verify that it is still up.
FAILBACK
This is used to configure failback, which is the ability to go back to a higher priority WAN interface if it regains
connection to its network.
Select the Failback Mode from the following
options:
•
•
•
Usage
Time
Disabled
Usage Threshold: Fail back based on the amount
of data passed over time. This is a good setting
for when you have a dual-mode EVDO/WiMAX
modem and you are going in and out of WiMAX
coverage. If the router has failed over to EVDO it
will wait until you have low data usage before bringing down the EVDO connection to check if a WiMAX connection can
be made.
•
•
•
•
High (Rate: 80 KB/s. Time Period: 30 seconds.)
Normal (Rate: 20 KB/s. Time Period: 90 seconds.)
Low (Rate: 10 KB/s. Time Period: 240 seconds.)
Custom (Rate range: 1-100 KB/s. Time Period range: 10-300 seconds.)
Time: Fail back only after a set period of time. (Default: 90 seconds. Range: 10-300 seconds.) This is a good setting if
you have a primary wired WAN connection and only use a modem for failover when your wired connection goes down.
This ensures that the higher priority interface has remained online for a set period of time before it becomes active
(in case the connection is dropping in and out, for example).
©2016 Cradlepoint. All Rights Reserved. | +1.855.813.3385 | cradlepoint.com
20
User Manual / AER2100
11/21/16
Disabled: Deactivate failback mode.
Immediate Mode: Fail back immediately whenever a higher priority interface is plugged in or when there is a priority
change. Immediate failback returns you to the use of your preferred Internet source more quickly which may have
advantages such as reducing the cost of a failover data plan, but it may cause more interruptions in your network than
Usage or Time modes.
DATA USAGE
Data Usage displays upload and download traffic for each
LAN client. Check Monitor Monthly (or Weekly or Daily)
Usage to begin tracking this information. This data is not
retained between router reboots.
For Monthly and Weekly you are able to specify the day to
start each cycle (e.g. the 1st or Tuesday, respectively).
Usage Cap: Enter a Cap amount in Megabytes. 1024
Megabyte is equal to 1 Gigabyte.
Use with Load Balancing: When checked, the Load
Balancing feature is allowed to use the thresholds and
metrics of this rule when making balance decisions. This
causes Load Balancing to spread the data usage between
interfaces according to the assigned usage rather than
bandwidth. This is a best effort to keep all interfaces with
these rules at a similar percentage utilization of data (e.g.
10%, 50%, 90%) as the cycle progresses, rather than quickly
using 100% of a fast 1GB capped interface while using only
a fraction of a slow 10GB capped interface, thus leaving the rest of the cycle with only the slow interface. The Data
Usage algorithm on the WAN Affinity/Load Balancing page must be selected or this checkbox has no effect.
Shutdown on Cap: When checked, the WAN device will shutdown when the assigned usage is reached. A cycle reset or
a rule deletion will re-enable the device.
Alert on Cap: An email alert will be generated and sent when the assigned data cap is reached. NOTE: The SMTP mail
server must be configured in System > Device Alerts.
Custom Alerts: Check to enable custom alerts at specified percentage of
usage cap.
Custom Alert Percentages: Example: “50,80,90,110” (values can exceed
100%) (Triggers alerts when 50, 80, 90, 110% of usage cap is used)
NOTE: To enable data usage, check Data Usage Enabled from WAN
Management.
©2016 Cradlepoint. All Rights Reserved. | +1.855.813.3385 | cradlepoint.com
21
User Manual / AER2100
11/21/16
STATUS
Internet
Client List
Tunnels
Firewall
Routing
Ethernet
GPS
LLDP
System Logs
INTERNET
CONNECTIONS
Select your device to reveal
detailed information about the
following device properties:
•
•
•
•
•
•
Summary
Modem
Cellular Network
General Information
IPv4 Information
Statistics
©2016 Cradlepoint. All Rights Reserved. | +1.855.813.3385 | cradlepoint.com
22
User Manual / AER2100
11/21/16
©2016 Cradlepoint. All Rights Reserved. | +1.855.813.3385 | cradlepoint.com
23
User Manual / AER2100
11/21/16
©2016 Cradlepoint. All Rights Reserved. | +1.855.813.3385 | cradlepoint.com
24
User Manual / AER2100
11/21/16
CLIENT DATA USAGE
Displays the following client information:
•
•
•
•
•
•
Name
IP Address
MAC Address
Data Uploaded
Data Downloaded
Last Traffic
To reset information, click Reset Statistics.
STATISTICS
Statistics can be gathered at variable Sample Rate and Sample Size for the following areas:
•
•
•
Wireless Device
Data Usage
Failover/Failback/Load Balance
©2016 Cradlepoint. All Rights Reserved. | +1.855.813.3385 | cradlepoint.com
25
User Manual / AER2100
11/21/16
QOS
Displays packets and bytes transmitted and
received by your Quality of Service (QoS) queues.
To enable and configure QoS, go to NETWORKING
> QoS.
©2016 Cradlepoint. All Rights Reserved. | +1.855.813.3385 | cradlepoint.com
26
User Manual / AER2100
11/21/16
CLIENT LIST
Displays information about
your Wireless, Wired, and
Hotspot Clients, and allows
you to Kick Wireless Clients,
block MAC addresses of both
Wireless and Wired Clients,
and Revoke Hotspot Clients.
TUNNELS
CP SECURE VPN
Displays status of your CP Secure
VPN Tunnels. To add and configure
CP Secure VPN Tunnels, go to
NETWORKING > Tunnels > CP Secure
VPN.
IPSEC VPN
Displays status of your IPSec VPN
Tunnels. To add and configure IPSec
VPN Tunnels, go to NETWORKING >
Tunnels > IPSec VPN.
©2016 Cradlepoint. All Rights Reserved. | +1.855.813.3385 | cradlepoint.com
27
User Manual / AER2100
11/21/16
OPEN VPN
Displays status of your OpenVPN Tunnels. To add and configure OpenVPN Tunnels, go to NETWORKING > Tunnels
> OpenVPN.
GRE
Displays status of your GRE Tunnels. To add and configure GRE Tunnels, go to NETWORKING > Tunnels > GRE.
FIREWALL
Displays information about your Firewall Connection Tracking States. To configure your firewall, select SECURITY
from the left navigation.
©2016 Cradlepoint. All Rights Reserved. | +1.855.813.3385 | cradlepoint.com
28
User Manual / AER2100
11/21/16
ROUTING
Displays information about your
System, GRE, and NEMO Routes.
To configure these routes, go to
NETWORKING > Tunnels.
ETHERNET
Displays information about your Ethernet ports. To configure
Ethernet ports, go to NETWORKING > Local Networks > Ethernet
Ports.
GPS
Displays GPS location and status. To enable and configure GPS, go to SYSTEM > Administration > GPS.
LLDP
Displays LLDP information. To enable LLDP, go to SYSTEM > Administration > LLDP.
©2016 Cradlepoint. All Rights Reserved. | +1.855.813.3385 | cradlepoint.com
29
User Manual / AER2100
11/21/16
SYSTEM LOGS
Displays System Log information. To configure System Logging, go to SYSTEM > Administration > System
Logging.
©2016 Cradlepoint. All Rights Reserved. | +1.855.813.3385 | cradlepoint.com
30
User Manual / AER2100
11/21/16
NETWORKING
Local Networks
VLAN Interfaces
Tunnels
Routing
QoS
DNS Servers
WiFi as WAN
WAN Affinity
Client Data Usage
NHRP
LOCAL NETWORKS
WIFI RADIO #1 (2.4GHZ)
WIFI RADIO #2 (5GHZ)
To edit your wireless
network, select its name and
click Edit.
WiFi Name (SSID): When users browse for available wireless
networks, this is the name that they will see. This name is
referred to as the SSID (service set identifier). For security
purposes, Cradlepoint highly recommends that you change
this from the pre-configured name.
Hidden: This shows whether the router broadcasts its SSID.
It is somewhat harder for hackers to find and attack a router
that is not broadcasting its SSID, which adds to the wireless
security, but it is also more difficult for friendly users to
attach to a WiFi network with a hidden SSID.
Isolate: Select this to isolate all wireless clients so they
cannot directly communicate with each other on the wireless
network.
WMM: WiFi Multimedia. This is a basic traffic shaping, or
QoS (quality of service), system for the network. WMM
works behind the scenes to set priorities for different types
©2016 Cradlepoint. All Rights Reserved. | +1.855.813.3385 | cradlepoint.com
31
User Manual / AER2100
11/21/16
of traffic on your network. For example, video streams are given higher priority than print jobs, since video
streams need consistent throughput.
Enabled: Whether the network is available.
Security Mode: You have several options for selecting a security mode. The mode you choose depends on the
security features your wireless adapters support.
•
•
•
•
•
•
•
•
WPA2 Personal
WPA / WPA2 Personal
WPA Personal
WPA2 Enterprise
WPA / WPA2 Enterprise
WPA Enterprise
WEP Auto
Open
Select “Open” to create a hotspot: otherwise select the best security that your devices will support
(Cradlepoint recommends WPA2).
Depending on which Security Mode you select, there are different setup options.
•
•
•
•
•
•
“Personal” security modes require passwords.
“Enterprise” security modes are linked to a RADIUS server and require RADIUS authentication: IP, Port, and
Shared Key (Secondary IP and NAS ID optional).
“WPA2” (Personal or Enterprise) forces AES as the WPA Cipher.
“WPA/WPA2” and “WPA” (Personal or Enterprise) allow AES, TKIP/AES, and TKIP.
“WEP Auto” requires a WEP Key.
“Open” has no password or other security measures.
NOTE: If you don’t know whether you should choose
Personal or Enterprise, assume Personal since you
need to know RADIUS authentication for Enterprise.
In order to protect your network from hackers and
unauthorized users, Cradlepoint highly recommends
WPA2/AES for security if your attached devices can
support it. WEP and WPA/TKIP are obsolete and have
been replaced by WPA/AES. Using those security
settings will cause the WiFi to limit to 802.11g modes.
NOTE: If you select one of the security modes and
are unable to connect to the router afterwards, you
can use the reset buttons to reset the router to its
factory default state and try a different security mode
instead.
When you select either WiFi Radio #1 (2.4GHz) or
WiFi Radio #2 (5GHz) from Local Networks, you have
several additional options for configuring your wireless
LANs under the WiFi Settings heading.
Channel Selection Method: This controls how a WiFi
channel is selected.
•
•
User Selection – Manually set the channel
Random Selection – The router randomly sets the
channel
©2016 Cradlepoint. All Rights Reserved. | +1.855.813.3385 | cradlepoint.com
32
User Manual / AER2100
•
11/21/16
Smart Selection (Default) – Scans to determine the lowest interference WiFi channel
Channel Selection Schedule: When using the “Smart” channel selection, this controls whether the router will
periodically rescan for a better channel and change to it. Select from “Once,” “Daily,” “Weekly,” or “Monthly.”
Note that there may be a momentary WiFi disconnection while the channel changes.
Channel: (Shows if User Selection is selected.) The WiFi channel* corresponds to a frequency the router uses to
communicate with other devices. For 2.4 GHz, the range is 1 to 11, and 1, 6, and 11 do not overlap each other.
Select a channel from the dropdown list:
•
•
•
•
•
•
•
•
•
•
•
1 (2412 MHz)
2 (2417 MHz)
3 (2422 MHz)
4 (2427 MHz)
5 (2432 MHz)
6 (2437 MHz)
7 (2442 MHz)
8 (2447 MHz)
9 (2452 MHz)
10 (2457 MHz)
11 (2462 MHz)
For 5.0 GHz, the ranges are 36 to 64 and 149 to 165.
•
•
•
•
•
•
•
•
•
36 (5180 MHz)
40 (5200 MHz)
44 (5220 MHz)
48 (5240 MHz)
149 (5745 MHz)
153 (5765 MHz)
157 (5785 MHz)
161 (5805 MHz)
165 (5825 MHz)
* - Channels listed above represent US/FCC settings. EU users will see different settings.
Client Timeout: If the access point is not able to communicate with the client it will disconnect it after this
timeout (in seconds).
TX Power: Normally the wireless transmitter operates at 100% power. In some circumstances, however, there
might be a need to isolate specific frequencies to a smaller area. By reducing the power of the radio, you can
prevent transmissions from reaching beyond your corporate/home office or designated wireless area.
RTS Threshold: When an excessive number of wireless packet collisions are occurring, wireless performance
can be improved by using the RTS/CTS (Request to Send/Clear to Send) handshake protocol. The wireless
transmitter will begin to send RTS frames (and wait for CTS) when data frame size in bytes is greater than the
RTS Threshold. This setting should remain at its default value.
Fragmentation Threshold: Wireless frames can be divided into smaller units (fragments) to improve
performance in the presence of RF interference and at the limits of RF coverage. Fragmentation will occur
when frame size in bytes is greater than the Fragmentation Threshold. This setting should remain at its default
value. Setting the Fragmentation value too low may result in poor performance.
DTIM: A DTIM is a countdown informing clients of the next window for listening to broadcast and multicast
messages. When the wireless router has buffered broadcast or multicast messages for associated clients, it
sends the next DTIM with a DTIM Interval value. Wireless clients detect the beacons and awaken to receive the
broadcast and multicast messages. The default value is 1. Valid settings are between 1 and 255.
©2016 Cradlepoint. All Rights Reserved. | +1.855.813.3385 | cradlepoint.com
33
User Manual / AER2100
11/21/16
Beacon: Beacons are packets sent by a wireless router to synchronize wireless devices. Specify a Beacon
Period value between 20 and 1000 milliseconds.
Short Slot: Slot Time is the period wireless clients use in determining if the channel is free for transmission.
Enabling this value allows clients that can utilize a shorter time to do so. Disabling this option forces all
clients to use a longer backoff check and thus may reduce network throughput while reducing the number of
transmission collisions.
Wireless Mode: Select the WiFi clients with which the router will be compatible. Greater compatibility is a
tradeoff with better performance. For greatest compatibility with all WiFi devices, select 802.11 a/b/g/n or
802.11 a/b/g/n/ac.
2.4 GHz options
5 GHz options
•
•
•
•
•
•
•
•
•
•
•
•
802.11 b
802.11 b/g
802.11 a/b/g/n
802.11 b/g/n
802.11 n
802.11 a/b/g/n/ac
802.11 g/n/ac
802.11 n/ac
802.11 ac
802.11 n
802.11 g
802.11 b
Protection: In Auto mode the device will use protection to improve performance in mixed mode networks. Turn
protection off to maximize throughput with 802.11n clients.
Airtime Fairness: Airtime Fairness will attempt to balance air time between faster and slower wireless clients
to more fairly distribute bandwidth.
Channel Width: Selects whether the router uses a single 20 MHz channel to send/receive, or uses two adjacent
20 MHz channels to create a 40 MHz channel. Higher performance is possible with the 40 MHz channel.
Selecting Auto is generally best. Enabling WiFi as WAN will force 20 MHz only mode.
Extended Channel: When operating in 40 MHz mode the access point will use an extended channel either below
or above the current channel. Optimal selection will depend on the channels of other networks in the area.
MCS: 802.11n uses multiple Modulation Coding Schemes to enable higher throughput in various environments.
Since clients can dynamically change rates depending on environment, selecting Auto is generally best.
Short GI: Short GI is an optimization for shortening the interval between transmissions. May be incompatible
with older clients.
RADIUS Timeout: (Default: 3600 seconds) When using an Enterprise security mode clients will be forced to reauthenticate with the RADIUS server at this interval in seconds. This allows administrators to revoke access so
when an attached client’s authentication expires, the client must re-authenticate.
RADIUS Retry: (Default: 60 seconds) When using an Enterprise security mode, if a RADIUS query fails to
receive a response from the server it will delay by this interval (in seconds) before attempting another query.
This helps protect the network from floods of authentication requests if the RADIUS server is temporarily
unreachable.
ETHERNET PORTS
Ethernet Port Configuration provides controls for your router’s Ethernet ports. There are 13 total ports:
by default, one WAN port and 12 numbered LAN ports. While default settings will be sufficient in most
circumstances, you have the ability to control: Mode (WAN or LAN) and Link Speed. Additional controls for WAN
ports are available in CONNECTION MANAGER.
©2016 Cradlepoint. All Rights Reserved. | +1.855.813.3385 | cradlepoint.com
34
User Manual / AER2100
11/21/16
Mode: WAN or LAN. By default there are 13 LAN (Local Area Network) ports and one WAN (Wide Area Network)
port.
•
•
Internet (WAN) is used as a possible source of Internet for the router
Local Network (LAN) is for connecting a computer or similar device directly to the router with an Ethernet
cable.
Link Speed: Default setting is Auto. The Auto setting is preferred in most cases.
•
•
•
•
•
•
Auto
10Mbps - Half Duplex
10Mbps - Full Duplex
100Mbps - Half Duplex
100Mbps - Full Duplex
1000Mbps - Full Duplex
HOTSPOT SERVICES
Any of your networks can be enabled as a
hotspot. To enable a hotspot, you need to
select a network and set it as a hotspot in
NETWORKING > Hotspot Services.
NOTE: Although any network can be a hotspot,
the router allows only one hotspot.
Hotspot Mode: Choose from the following
dropdown options:
•
•
Simple: Allows “Terms of Use” page and
timeout settings controlled within the
router
RADIUS/UAM: Allows you to set up external
authentication servers
Local IP Network: A single LAN Group – including both WiFi and Ethernet – can be configured as your hotspot.
If you do not already have a LAN Group configured as a hotspot, click Configure and set the IPv4 Routing Mode
to “Hotspot” for the LAN Group you want to use.
NOTE: Routing Mode is in the Primary LAN Editor under the IPv4 Settings tab. Select a network in
NETWORKING > Local IP Networks and click Edit to open the Primary LAN Editor.
Allow Service on 3G/4G Modems: Allows you to enable or disable hotspot access to the Internet over a modem.
This is often used if the router has a main wired link and a secondary modem for failover (typically with a more
expensive/limited data plan). Select this option if you want the router to allow data traffic over the modem if
the wired connection goes down.
Disable Service if Ethernet Threshold is met: This will block hotspot use of the WAN when the threshold is
met. This can be used if the router is being used as a backup failover connection to another router with a wired
connection. If that other router’s wired connection goes down and it starts using this router for its primary
connection, then disable hotspot use of the WAN connection. Set the limiting Rate (KB/s) and Time Period
(seconds).
Redirect HTTPS Requests: This allows initial requests to HTTPS websites to be redirected appropriately.
Hotspot/UAM Authentication Port: Default: 8000. Type in a different port number, or use the slider to change
the port.
©2016 Cradlepoint. All Rights Reserved. | +1.855.813.3385 | cradlepoint.com
35
User Manual / AER2100
11/21/16
Simple Mode Settings
Display: This section allows you to choose if a “Terms
of Use” page will be given to the user connecting to
the hotspot.
•
•
•
Internal Terms of Use. Fill in your own terms of
use.
External Terms of Use. Specify a URL that has the
Terms of Use page. Users will automatically be
directed to this page.
No Terms of Use. Redirect Only.
Redirection on Successful Authentication: Depending
on your choice for the “Terms of Use” page, your have
further options for where the user will be directed.
After the user accepts the terms, you can either
let him/her continue to the URL they were trying to
reach or you can force the user to go to a specified
URL once before continuing on.
•
•
To the URL the user intended to visit
To an administrator-defined URL
Redirect URL: If you have chosen to send users to an
administrator-defined URL, you will need to specify the address.
Session Timeout: (Default: 60 minutes.) The amount of time the user may use the router before being forced to
authenticate again.
Idle Timeout: (Default: 15 minutes.) If the user is idle for this amount of time, make them re-authenticate.
Bandwidth (upload): (Default: 512 Kbits/sec.) The data rate limit for users uploading data through the hotspot.
Bandwidth (download): (Default: 1024 Kbits/sec.) The data rate limit for users downloading data through the
hotspot.
Allowed Hosts/Domains Prior to Authentication
Adding hostnames to this list will allow access from your
network to any external domain or website prior to being
authenticated. For example, a hotel might allow access to
its own website prior to authentication.
Click Add to enter new hostnames you wish to allow.
Enter the hostname or domain name of the website you
wish to allow, e.g. www.company.com or company.com. To
allow all domain and sub-domain options, use a wildcard, e.g. *.company.com.
Click Update to save your additions.
Authorized MAC Addresses
Add the MAC addresses of trusted machines. This gives them automatic
access through the hotspot portal.
Click Add to enter new MAC Addresses you wish to allow.
Click Update to save your additions.
©2016 Cradlepoint. All Rights Reserved. | +1.855.813.3385 | cradlepoint.com
36
User Manual / AER2100
11/21/16
DHCP SERVER
DHCP stands for Dynamic Host Configuration Protocol. The built-in DHCP server automatically assigns IP
addresses to the computers and other devices on each local area network (LAN). In this section you can view a
list of assigned IP addresses and reserve IP addresses for particular devices.
Active Leases: A list of devices that have
been provided DHCP leases. The DHCP server
automatically assigns these leases. This list
will not include any devices that have static
IP addresses on the network. Select a device
and click Reserve to add the device and its IP
address to the list of Reservations.
Reservations: This is a list of devices with
reserved IP addresses. This reservation is
almost the same as when a device has a static
IP address except that the device must still
request an IP address from the router. The
router will provide the device the same IP
address every time. DHCP reservations are
helpful for server computers on the local network that are hosting applications such as Web and FTP. Servers
on your network should either use a static IP address or a reservation.
While you have the option to manually input the information to reserve an IP address (Hostname, Hardware
Addr, IP Addr), it is much simpler to select a device under the Active Leases section and click “Reserve.” The
selected device’s information will automatically be added under Reservations.
LOCAL IP NETWORKS
Local IP Networks displays the following information for
each network:
•
•
•
•
•
•
•
•
•
•
Network Name, IP address/Netmask, and Enabled/
Disabled (along the top bar)
Multicast Proxy (Enabled/Disabled)
DHCP Server (Enabled/Disabled)
DHCP Relay (Enabled/Disabled)
Schedule (Enabled/Disabled – See the Schedule tab in
the Local Network Editor)
VRRP Failover State (Disabled, Backup, or Master)
IPv4 Routing Mode (NAT, Standard, IP Passthrough,
Hotspot, Disabled)
IPv6 Addressing Mode (SLAAC Only, SLAAC with
DHCP, Disable SLAAC and DHCP)
Access Control (Admin Access, UPnP Gateway, LAN Isolation)
Attached Interfaces (Ethernet ports, WiFi, VLAN)
Click Add to configure a new network, Remove to delete a network, or select an existing network and click Edit
to view configuration options.
General Settings
Enabled: The network can be manually disabled or in some specific situations may be automatically disabled to
work with certain types of modems.
©2016 Cradlepoint. All Rights Reserved. | +1.855.813.3385 | cradlepoint.com
37
User Manual / AER2100
11/21/16
Name: The “name” property primarily helps to identify
this network during other administration tasks.
Hostname: The hostname is the DNS name associated
with the router’s local area network IP address.
IPv4 Settings
IP Address: This is the address used by the router for
local area network communication. Changes to this
parameter may require a restart to computers on this
network.
Netmask: The netmask controls how many IP addresses
can be used in this network. The default value is usually
acceptable for most situations.
IPv4 Routing Mode: Each network can use a unique
routing mode to connect to the Internet. The default of
NAT is desirable in most configurations.
• NAT: Network Address Translation hides private IP addresses behind the router’s IP address.
• Standard: Without NAT exposes the subnet addresses which requires them to be externally routable.
• IP Passthrough: IP Passthrough passes the IP address given by the modem WAN through the router.
Hotspot, VPN, and GRE must be disabled. Any Wireless interfaces must be removed from this network in
order to enable IP Passthrough.
• Hotspot: Provide Hotspot Services on this Network, requiring Terms of Service or RADIUS/UAM
authentication before WAN access will occur on both Wireless and Wired LAN connections.
IPv6 Settings
IPv6 Address Source: The Address source has three settings. The default of Delegated is desirable in most
configurations.
•
•
•
Delegated: The address is provided by a router connected to this router’s WAN.
Static: The address is provided by the router admin.
None: No use of an IPv6 WAN address, IPv6 is disabled on the WAN.
IPv6 Address: An IPv6 Address is a unique numerical label for a computer or device using the Internet Protocol
(IP). IPv6 addresses are typically in the format composed of 8 sets of 4 hexadecimal numbers. Leading zeros
can be ignored and the longest set of continuous zeros can be replaced with ::. For example, the IPv6 address
of 0001:0000:0234:5678:0000:0000:9abc:0def can be expressed as 1:0:234:5678::9abc:def.
Interfaces
Select the network interfaces which will
be attached to this network by either
dragging desired interface or clicking left
or right arrows to move them between
Available Interfaces and Selected
Interfaces.
Access Control
UPnP Gateway: Select the UPnP
(Universal Plug and Play) option if you
want to enable the UPnP Gateway service
for computers on this network.
Admin Access: When enabled users may access these admin pages from this network.
©2016 Cradlepoint. All Rights Reserved. | +1.855.813.3385 | cradlepoint.com
38
User Manual / AER2100
11/21/16
IPv4 DHCP
DHCP Server
• Enable DHCP Server: When the DHCP server is
enabled, users of your network will be able to
automatically connect to the Internet without
any special configuration. It is recommended
that you leave this enabled. Advanced
DHCP server configuration is available at
NETWORKING > Local Networks > DHCP
Server.
• Range Start: The starting IP address in the
DHCP Server range is the beginning of the
reserved pool of IP addresses which will be
given to any DHCP enabled computers on your
network. The default value is almost always sufficient.
• Range End: The ending IP address in the DHCP Server range is the end of the reserved pool of IP
addresses which will be given to any DHCP enabled computers on your network. The default value is
almost always sufficient.
• Lease Time: The lease time specifies how long DHCP enabled computers will wait before requesting a
new DHCP lease. Smaller values are better suited to busy environments.
• Custom Options: Send optional extra options to DHCP clients of this network. This can be used to, for
example, set the boot TFTP server of a network for disk-less clients.
DHCP Relay
• Enable DHCP Relay: DHCP Relay communicates with a DHCP server and acts as a proxy for DHCP
broadcast messages that must be routed to remote segments. This is accomplished by converting
broadcast DHCP messages to unicast messages to communicate between clients and servers.
Multicast Proxy
Multicast Proxy: Enables IGMP proxying to allow Multicast Streams to flow across this network.
Quick Leave Mode: Disable quick leave mode if it’s vital that the daemon should act exactly as a real multicast
client on the upstream interface. However, disabling this function increases the risk of bandwidth saturation.
Altnet: If multicast traffic originates outside the upstream subnet, add address(es) to the “altnet” to define
legal multicast sources.
IPv6 Addressing
Address Configuration Mode: SLAAC stands for Stateless address autoconfiguration. A network can be configured
to use SLAAC only, or it can be configured to also use DHCPv6 to provide ip addresses to clients.
DHCP Range Start: The DHCP Range Start is the beginning of the range that will be used for IPV6 DHCP
addresses. The IPv6 range will always start at 1.
DHCP Range End: The ending IP address in the DHCP Server range is the end of the reserved pool of IP addresses
which will be given to any DHCP enabled computers on your network.
IPv6 DHCP Lease Time: Specifies how long DHCP enabled computers will wait before requesting a new DHCP
lease.
Schedule
Enable Schedule Service: Enable the interface scheduler. A schedule allows an interface to be enabled or disabled
during specific hours of a day.
VRRP
Enable VRRP: Enable or disable VRRP.
©2016 Cradlepoint. All Rights Reserved. | +1.855.813.3385 | cradlepoint.com
39
User Manual / AER2100
11/21/16
Virtual Router IP: IP Address of the Virtual Router.
Virtual Router ID: Identifier of the Virtual Router.
Router Priority: Failover priority of this router. The highest
priority router will take ownership of the Virtual IP.
WAN Fault Priority: This optional value sets the failover priority
of this router when no WAN connection is available. If the value
matches the normal router priority, WAN connection state
will not be considered. If the value is empty (the default), the
router will always give up the Virtual IP and let a new master
take over when no WAN connection is available.
Advertisement Interval: Sets the amount of time (in seconds)
between sending VRRP advertisements.
Initial Value Router State: This controls the initial failover state
of the VRRP instance when it first comes up.
Authentication: VRRP Authentication Method. Note that VRRP
Authentication has been deprecated as of RFC 3768.
Password: VRRP Group Password.
Provide Virtual IP in DHCP leases: Select this to automatically set the DHCP default gateway address and DNS
server address to the Virtual IP in DHCP leases provided on this network.
STP
Enable STP: Enable Spanning Tree Protocol loop detection.
Bridge Priority: Set the priority of the bridge. When determining the root bridge of the spanning tree topology,
the bridge priority is compared first. The bridge with the lowest priority with will win. If you want this router to
be the root bridge, then set it to a value less than the default of 32768. A valid priority value is between 0 and
65535.
Wired 802.1X
Enable 802.1X: Require IEEE 802.1X Authorization.
Reauthentication Period: EAP reauthentication period in
seconds.
Auth Server IP Address: IP address of the connected RADIUS
server.
Auth Server MAC Address: Hardware address of the
connected RADIUS server’s interface. NOTE: If you don’t
know the MAC address for the RADIUS server, enter
00:00:00:00:00:00, and the service will try to find the MAC
address from the given IP address.
Port
Password
Acct Server IP Address: IP address of the connected RADIUS
server.
Acct Server MAC Address: This is the Hardware address
of the connected RADIUS server’s interface. NOTE: If you
don’t know the MAC address for the RADIUS server, enter
00:00:00:00:00:00, and the service will try to find the MAC
address from the given IP address.
Port
Password
©2016 Cradlepoint. All Rights Reserved. | +1.855.813.3385 | cradlepoint.com
40
User Manual / AER2100
11/21/16
MAC FILTER & LOGGING
A MAC (Media Access Control) address is a unique identifier for a computer or other device. This page allows
you to manage clients by MAC address. You can filter clients by MAC addresses and/or keep a log of devices
connected to your router.
Filter Configuration
The MAC Filter allows you to create a list of devices that have either exclusive access (whitelist) or no access
(blacklist) to your local network.
Enabled: Click to allow MAC Filter options.
Whitelist: Select either “Whitelist” or “Blacklist” from
a dropdown menu. In “Whitelist” mode, the router
will restrict LAN access to all computers except those
contained in the “MAC Filter List” panel. In “Blacklist”
mode, listed devices are completely blocked from local
network access.
MAC Filter List (Whitelist or Blacklist)
Add devices to either your whitelist or blacklist simply
by inputting each device’s MAC address.
NOTE: Use caution when using the MAC Filter to avoid
accidentally blocking yourself from accessing the
router.
MAC Logging Configuration
Enable MAC Logging: Enabling MAC Logging will cause the router to
log MAC addresses that are connected to the router. MAC addresses
that you do not want to have logged (addresses that you expect to be
connected) should be added to the “Ignored MAC Addresses” list.
You can configure the router to send an alert if a connected device
has a MAC address that the router doesn’t recognize. Go to SYSTEM >
Device Alerts to set up these email alerts.
Ignored MAC Addresses
This is the list of MAC addresses that will not produce an alert or a log
entry when they are connected to the router. These should be MAC
addresses that you expect to be connected to the router. To add MAC
addresses to this list, simply select devices shown in the MAC Address
Log and click “Ignore.” You can also add addresses manually.
MAC Address Log
This shows the last 64 MAC addresses that have connected to the router, as well as which interface was used
to connect. The time/date that is logged is the time of the first connection. The page may need to be refreshed
to show the most recent log entries.
Double-clicking on entries from this list will add them to the Ignored MAC Addresses list.
©2016 Cradlepoint. All Rights Reserved. | +1.855.813.3385 | cradlepoint.com
41
User Manual / AER2100
11/21/16
VLAN INTERFACES
A virtual local area network, or VLAN, functions as
any other physical LAN, but it enables computers
and other devices to be grouped together even
if they are not physically attached to the same
network switch.
To enable a VLAN, select a VID (virtual LAN ID) and
a group of Ethernet ports through which users
can access the VLAN. Then go back up to the Local
Network Editor to attach your new VLAN to a
network. To use a VLAN, the VID must be shared
with another router or similar device so that
multiple physical networks have access to the one
virtual network.
Click Add to create a new VLAN interface. To edit
an interface, select the check box next to the
desired interface.
TUNNELS
CP SECURE VPN
Configured, deployed, and managed from the cloud, CP Secure VPN delivers a virtual
private data network that minimizes both cost and complexity. Unlike traditional
bulky head-end concentrator hardware solutions, CP Secure VPN allows IT
managers to secure their expanding Edge Networks using architectures that scale
quickly and are easy to maintain. For more information, visit cradlepoint.com.
NOTE: CP Secure VPN requires an ECM Prime subscription. For more information,
visit cradlepoint.com.
©2016 Cradlepoint. All Rights Reserved. | +1.855.813.3385 | cradlepoint.com
42
User Manual / AER2100
11/21/16
IPSEC VPN
VPN (virtual private network) tunnels
are used to establish a secure
connection to a remote network over
a public network. For example, VPN
tunnels can be used across the Internet
by an individual to connect to an office
network while traveling, or by two office
networks to function as one network. The two networks set up a secure connection across the (normally)
unsecure Internet by assigning VPN encryption protocols.
Cradlepoint VPN tunnels use IPsec (Internet Protocol security) to authenticate and encrypt packets exchanged
across the tunnels. To set up a VPN tunnel with a Cradlepoint router on one end, there must be another device
(usually a router) that also supports IPsec on the other end.
IKE (Internet Key Exchange) is the security protocol in IPsec. IKE has two phases, phase 1 and phase 2. The
router has several different security protocol options for each phase, but the default selections will be
sufficient for most users.
The VPN tunnel status page allows you to view the state of the VPN tunnels. If a tunnel fails to connect to the
remote site, check the System Logs for more information. You may double click on a cell to directly edit that
information.
Click Add to configure a new VPN tunnel; click Edit to make changes to an existing tunnel.
Add/Edit Tunnel – General
Tunnel Name: Give the tunnel a name that uniquely
identifies it.
Anonymous Mode: Select to allow remote connections
from any IP address.
Responder Mode: When enabled, the router will not
initiate negotiation with peers.
Local Identity: Specifies the identifier sent to the
remote host during phase 1 negotiation. If left blank it
will default to the IP address of the WAN connection.
Currently we only support identifiers in the form of an
IP address, a user-fully qualified domain name (user@
mydomain.com) or just a fully qualified domain name
(www.mydomain.com). If the remote side of the tunnel
is configured to expect an identifier, then both must
match in order for the negotiation to succeed. If NAT-T is being used, a single word (instead of an address) can
be used if a DynDNS connection is not being used.
Remote Identity: Specifies the identifier we expect to receive from the remote host during phase 1
negotiation. If no identifier is defined then no verification of the remote peer’s identification will be done.
Currently we only support identifiers in the form of an IP address, a user-fully qualified domain name (user@
mydomain.com) or just a fully qualified domain name (www.mydomain.com). If left blank we will default to the
IP address of the WAN connection. If NAT-T is being used, a single word (instead of an address) can be used if a
DynDNS connection is not being used.
Authentication Mode: Select from Pre-Shared Key and Certificate. Pre-Shared Key is used when there is a
single key common to both ends of the VPN. Certificate requires the creation of a set of certificates and a
©2016 Cradlepoint. All Rights Reserved. | +1.855.813.3385 | cradlepoint.com
43
User Manual / AER2100
11/21/16
private key that can be uploaded to the router. Select Enable Certificate Support in the Global VPN Settings
section to upload a single set of certificates for the router to use.
Pre-Shared Key: Create a password or key. The routers on both sides of the tunnel must use this same key.
Mode: Select from Tunnel, Transport or VTI-Tunnel. Tunnel Mode is used for protecting traffic between
different networks, when traffic must pass through an intermediate, untrusted network. Transport Mode is
used for end-to-end communications (for example, for communications between a client and a server). VTI
Tunnel creates a virtual tunnel interface with a specified virtual IP address. This interface can then be added to
the zone firewall.
Initiation Mode: Always On or On Demand. Always On
is used if you want the tunnel to initiate the tunnel
connection whenever the WAN becomes available.
Select On Demand if you want the tunnel to initiate a
connection if and only if there is data traffic bound for
the remote side of the tunnel.
Tunnel Enabled: Enabled or Disabled.
Add/Edit Tunnel – Local Gateway
IP Version: Select IPv4 or IPv6.
WAN Binding: WAN Binding is an optional parameter
used to configure the VPN tunnel to ONLY operate when
the specified WAN device(s) are available and connected.
An example use case is when there is a router with both
a primary and failover WAN device and the tunnel should only be used when the system has failed over to the
backup connection.
Make a selection for “When,” “Condition,” and “Value” to create a WAN Binding. The condition will be in the
form of these examples:
When
Condition
Value
Port
Is
USB Port 1
Type
Is not
WiMax
•
When:
•
•
•
•
•
•
•
•
•
Port – Select by the physical port on the router that you are plugging the modem into (e.g., “USB
Port 2”).
Manufacturer – Select by the modem manufacturer (e.g., “Cradlepoint Inc.”).
Model – Set your rule according to the specific model of modem.
Type – Select by type of Internet source (Ethernet, LTE, Modem, Wireless as WAN, WiMAX).
Serial Number – Select a 3G or LTE modem by the serial number.
MAC Address – Select a WiMAX modem by MAC Address.
Unique ID – Select by ID. This is generated by the router and displayed when the device is connected
to the router.
Condition: Select “is,” “is not,” “starts with,” “contains,” or “ends with” to create your condition’s
statement.
Value: If the correct values are available, select from the dropdown list. You may need to manually input
the value.
Invert Binding: Advanced option that inverts the meaning of WAN Binding to only establish this tunnel when
the specified WAN Binding device(s) are NOT connected.
©2016 Cradlepoint. All Rights Reserved. | +1.855.813.3385 | cradlepoint.com
44
User Manual / AER2100
11/21/16
Add/Edit Tunnel – Local Networks
IP Version: Select IPv4 or IPv6.
The Network Address and the Netmask define what local devices have access to or can be accessed from the
VPN tunnel.
NOTE: the local network IP address MUST be different from the remote network IP address.
Optionally: A Port can be defined that will limit the traffic going through the VPN tunnel to only that port. If
the field is left blank, any port will be accepted by the tunnel.
Add/Edit Tunnel – Remote Gateway
Gateway: This value can be any of the following: an
IPv4 address, an IPv6 address, or a fully qualified
name in the form of “host.domain.com” (DNS names
are case-insensitive, so only lower case letters are
allowed). It is recommended that you use a dynamic
DNS hostname instead of the static IP address – by
using the dynamic DNS hostname, updates of the
remote WAN IP are compensated for while connecting
to a VPN tunnel.
Add/Edit Tunnel – Remote Networks
The Network Address and the Netmask define the
remote network address range that local devices will
have access to via the VPN tunnel.
NOTE: the remote network IP address MUST be
different from the local network IP address.
Optionally: A Port can be defined that will limit the traffic going through the VPN tunnel to only that port. If
the field is left blank, any port will be accepted by the tunnel.
Add/Edit Tunnel – IKE Phase 1
IKE security has two phases, phase 1 and phase 2. You have the ability to distinctly configure each phase, but
the default settings will be sufficient for most users.
To set up a tunnel with a remote site, you need to match your tunnel’s IKE negotiation parameters with
the remote site. By selecting several encryption, hash, and DH group options, you improve your chances
for a successful tunnel negotiation. For greatest
compatibility, select all options; for greatest security,
select only the most secure options that your devices
support.
Exchange Mode: The IKE protocol has two modes
of negotiating phase 1 – Main (also called Identity
Protection) and Aggressive.
•
In Main mode, IKE separates the key information
from the identities, allowing for the identities
of peers to be secure at the expense of extra
packet exchanges.
©2016 Cradlepoint. All Rights Reserved. | +1.855.813.3385 | cradlepoint.com
45
User Manual / AER2100
•
11/21/16
In Aggressive mode, IKE tries to combine as much information into fewer packets while maintaining
security. Aggressive mode is slightly faster but less secure.
Because it has better security, Main mode is recommended for most users.
Key Lifetime: The lifetime of the generated keys of phase 1 of the IPsec negotiation from IKE. After the time
has expired, IKE will renegotiate a new set of phase 1 keys.
Encryption, Hash, and DH Groups
Each IKE exchange uses one encryption algorithm, one hash function, and one DH group to make a secure
exchange.
Encryption: Used to encrypt messages sent and received by IPsec.
•
•
•
•
AES 128
AES 256
DES
3DES
Hash: Used to compare, authenticate, and validate that data across the VPN arrives in its intended form and to
derive keys used by IPSec.
•
•
•
•
•
MD5
SHA1
SHA2 256
SHA2 384
SHA2 512
Note that some Encryption/Hash combinations (e.g., 3DES with SHA2 384/512) are computationally expensive,
impacting WAN performance. AES is as strong an encryption and performs much better than 3DES.
DH Groups: The DH (Diffie-Hellman) Group is a property of IKE and is used to determine the length of prime
numbers associated with key generation. The strength of the key generated is partially determined by the
strength of the DH Group. Group 5, for instance, has greater strength than Group 2.
•
•
•
Group 1: 768-bit key
Group 2: 1024-bit key
Group 5: 1536-bit key
In IKE Phase 1 you can only select one DH group if you are using Aggressive exchange mode.
By default, all the algorithms (encryption, hash, and DH groups) supported by the device are checked, which
means they are allowed for any given exchange. Deselect these options to limit which algorithms will be
accepted. Be sure to check that the router (or similar device) at the other end of the tunnel has matching
algorithms.
The algorithms are listed in order by priority. You can reorder this priority list by clicking and dragging
algorithms up or down. Any selected algorithm may be used for IKE exchange, but the algorithms on the top of
the list are more likely to be used more often.
Add/Edit Tunnel – IKE Phase 2
Perfect Forward Secrecy (PFS): Enabling this feature will require IKE to generate a new set of keys in phase
2 rather than using the same key generated in phase 1. Additionally, with this option enabled the new keys
generated in phase 2 are exchanged in an encrypted session. Enabling this feature affords the policy greater
security.
Key Lifetime: The lifetime of the generated keys of phase 2 of the IPsec negotiation from IKE. After the time
has expired, IKE will renegotiate a new set of phase 2 keys.
©2016 Cradlepoint. All Rights Reserved. | +1.855.813.3385 | cradlepoint.com
46
User Manual / AER2100
11/21/16
Phase 2 has the same selection of Encryption and DH Groups as phase 1, but you are restricted to only one
DH Group. Phase 2 and phase 1 selections do not have to match. For the Hash selection an added value of
SHA 256_128 (128-bit truncation) is avaliable. The original specification and the Cradlepoint default is 96-bit
truncation, but RFC4868 requires 128-bit. A VPN to newer Cisco or Juniper devices will typically require 128-bit.
Add/Edit Tunnel – Dead Peer Detection
Dead Peer Detection (DPD) defines how the router
will detect when one end of the IPsec session loses
connection while a policy is in use.
Connection Idle Time: Configure how long the router
will allow an IPsec session to be idle before beginning
to send Dead Peer Detection (DPD) packets to the
peer machine. (Default: 30 seconds. Range: 10 – 3600
seconds.)
Request Frequency allows you to adjust the delay
between these DPD packets. (Default: 15 seconds.
Range: 2 – 30 seconds.)
Maximum Requests: Specify how many requests to
send at the selected time interval before the tunnel
is considered dead. (Default: 5. Range: 2 – 10.)
Failback Retry Period: If you have VPN tunnel failover/failback enabled (see below), set the time period
between each check on the primary network after failover. (Default: 10 seconds. Range: 5 – 60 seconds.)
Failover Tunnel and Failback Tunnel: Use these settings to create two tunnels – one as the primary tunnel and
one as the backup tunnel. To configure tunnel failover/failback, complete the following steps:
1. Create two tunnels: one for primary and one for backup. Make sure that both tunnels have the same
Remote Network and that both have Dead Peer Detection enabled.
2. Choose one to be the primary tunnel. Open the editor for this tunnel and make sure Tunnel Enabled is
selected. Then go to the Dead Peer Detection page. Under Failover Tunnel select the other tunnel you
have created.
3. Open the editor for the failover tunnel. Make sure Tunnel Enabled is not selected. On the Dead Peer
Detection page, set the Failback Tunnel to your primary tunnel.
Global VPN Settings
These settings apply to all configured VPN tunnels.
Enable VPN Service: Enabling VPN Service will allow you to
load a certificate for VPN to the router.
Certificate Name: Select the Certificate Name.
IKE / ISAKMP Port: Internet Key Exchange / Internet
Security Association and Key Management Protocol port.
(Default: 500. This is a standard VPN port that usually
does not need to be changed.)
IKE / ISAKMP NAT-T Port: Internet Key Exchange / Internet
Security Association and Key Management Protocol
network address translation traversal port. (Default:
4500. This is a standard VPN NAT-T port that usually does not need to be changed.)
©2016 Cradlepoint. All Rights Reserved. | +1.855.813.3385 | cradlepoint.com
47
User Manual / AER2100
11/21/16
NAT-T KeepAlive Interval: Number of seconds between sending NAT-T packets to keep the tunnel alive if no
other traffic is being sent. (Default: 20 seconds. Range: 0-3600 seconds. 20 seconds will be sufficient in almost
all cases.)
Tunnel Connect Retry: Number of seconds between connection attempts. (Default: 30 seconds. Range: 10-255
seconds. 30 seconds will be sufficient in almost all cases.)
OPEN VPN
OpenVPN is an open source software application that implements virtual private network (VPN) techniques
for creating secure point-to-point or site-to-site connections in routed or bridged configurations and remote
access facilities.
NOTE: OpenVPN requires a feature license not included with ECM Prime. Go to SYSTEM > Administration >
Feature Licenses to enable this feature.
Once you have a valid feature license, click Add to
create a new OpenVPN tunnel. Click Edit to make
changes to an existing tunnel.
Add/Edit Tunnel – General
• Tunnel Name – Enter a name to uniquely
identify this tunnel
• Tunnel Mode – Select which mode this tunnel
endpoint is required to be. Choose from the
following:
•
•
•
Device Type - Select between Routed (TUN)
or Bridged (TAP) virtual device.
•
•
•
•
•
•
•
•
•
•
•
•
Client
Server
Routed creates an interface that can
be used in the Zone Firewall and is fully
routable.
Bridged creates a network interface that
can be assigned to a LAN under the Local Networks configuration. This interface is managed through
the assigned LAN device.
Local Endpoint - Enter the IP Address of the LNS (tunnel server) peer
Local Netmask – Enter the Netmask of the LNS (tunnel server) peer
Remote Endpoint – Enter the IP Address of the LNS (tunnel server) peer
Remote Netmask – Enter the Netmask of the LNS (tunnel server) peer
Support IPv6 Tunnels – Allow IPv6 traffic to be forwarded over this tunnel. If you select this option, also
input an IPv6 Tunnel Address and Tunnel Prefix Length for IPv6
Tunnel Protocol – Choose UDP or TCP
Port – Specify the port if desired
Ping – (Displays if the Configuration Mode is Advanced) If no packets have been sent in the amount of
time entered, a ping is sent to the remote endpoint
Ping Restart – (Displays if the Configuration Mode is Advanced) If no pings have been received in the
amount of time entered, OpenVPN restarts the tunnel
Tunnel Enabled – Click to enable/disable this tunnel
©2016 Cradlepoint. All Rights Reserved. | +1.855.813.3385 | cradlepoint.com
48
User Manual / AER2100
11/21/16
Add/Edit Tunnel – Security
•
•
•
•
Cipher – Encrypt packets with the selected algorithm.
The default is BF-CBC, an abbreviation for Blowfish in
Cipher Block Chaining mode. Blowfish has the advantages
of being fast, very secure, and allowing key sizes of up
to 448 bits. Blowfish is designed to be used in situations
where keys are changed infrequently. OpenVPN supports
the CBC, CFB, and OFB cipher modes, however CBC is
recommended and CFB and OFB should be considered
advanced modes.
Auth Algorithm – Authenticate packets with HMAC using
message digest algorithm alg. (The default is SHA1).
HMAC is a commonly used message authentication
algorithm (MAC) that uses a data string, a secure hash
algorithm, and a key, to produce a digital signature.
Verify peer certificate — Verifies that peer certificate
was signed with RFC3280 TLS rules set in key usage and
extended key usage. This helps to prevent specific manin-the-middle attacks.
TLS-Authentication – In client/server mode: adds an additional layer of HMAC authentication on top of the
tls control channel to protect against DoS attacks. In point-to-point mode: encrypts the communication
using a static key. These keys must match on each endpoint.
Add/Edit Tunnel – Remote Servers
Create a list of remote server connections to connect to. OpenVPN will try to connect to each host in the list. If
a disconnect occurs from a given server, the next server will be tried in a round-robin fashion.
•
•
•
Host – IP address of the remote server
Port – Specify the port if desired
Protocol – Select UDP or TCP
Add/Edit Tunnel – Routes
Add or remove the routes that will be used to direct packets through the tunnel.
•
•
Network Address
Netmask
Generate Client Configuration
The Generate Client Configuration button can be used to generate client configurations for OpenVPN tunnels
configured in Server mode. An .ovpn file will be created that can be imported to a variety of OpenVPN client
devices (Android, iOS, Windows). If the private key for the server’s certificate authority is known, a client
certificate can be generated; otherwise one can be selected.
GRE
Generic Routing Encapsulation (GRE) tunnels can be used to create a connection between two private
networks. Most Cradlepoint routers are enabled for both GRE and VPN tunnels. GRE tunnels are simpler to
configure and more flexible for different kinds of packet exchanges, but VPN tunnels are much more secure.
In order to set up a tunnel you must configure the following:
©2016 Cradlepoint. All Rights Reserved. | +1.855.813.3385 | cradlepoint.com
49
User Manual / AER2100
•
•
•
11/21/16
Local Network and Remote Network addresses for the “Glue Network,” the network that is created by
the administrator that serves as the “glue” between the networks of the tunnel. Each address must be a
different IP address from the same private network, and these addresses together form the endpoints of
the tunnel.
Remote Gateway, the public facing WAN IP address that the local gateway is going to connect to.
Routes that allow you to configure what network traffic from local host(s) will be allowed through the
tunnel.
Optionally, you might also want to enable the tunnel Keep Alive feature to monitor the status of a tunnel and
more accurately determine if the tunnel is alive or not.
Click Add to configure a new GRE tunnel; click Edit to make changes to an existing tunnel.
Add/Edit Tunnel – General
Tunnel Name: Give the tunnel a name that uniquely identifies it.
Tunnel Key: Enables an ID key for a GRE
tunnel, which can be used as an identifier
for mGRE (Multipoint GRE).
Local Network: This is the local side of
the “Glue Network,” a network created
by the administrator to form the tunnel.
The user creates the IP address entered
here. It must be different from the IP
addresses of the networks it is gluing
together. Choose any private IP address
from the following three ranges that
doesn’t match either network:
•
•
•
10.0.0.0 - 10.255.255.255
172.16.0.0 - 172.31.255.255
192.168.0.0 - 192.168.255.255
Remote Network: This is the remote side
of the “Glue Network.” Again, the user
must create an IP address that is distinct
from the IP addresses of the networks
that are being glued together.
The Remote Network and Local Network values will be flipped when inputted for the other side of the tunnel
configuration.
Subnet Mask: This is the subnet mask for the Glue Network. The Local and Remote Network addresses must fit
with this mask. 255.255.255.0 is a logical choice for most users.
Remote Gateway: This is the public facing, WAN-side IP address of the network to which the local gateway is
going to connect.
TTL: Set the Time to Live (TTL), or hop limit, for the GRE tunnel.
MTU: Set the maximum transmission unit (MTU) for the GRE tunnel.
WAN Binding: WAN Binding is an optional parameter used to configure the GRE tunnel to ONLY operate when
the specified WAN device(s) are available and connected. An example use case is when there is a router with
both a primary and failover WAN device and the tunnel should only be used when the system has failed over to
the backup connection.
©2016 Cradlepoint. All Rights Reserved. | +1.855.813.3385 | cradlepoint.com
50
User Manual / AER2100
11/21/16
Make a selection for “When,” “Condition,” and “Value” to create a WAN Binding. The condition will be in the
form of these examples:
When
Condition
Value
Port
Is
USB Port 1
Type
Is not
WiMax
•
When:
• Port – Select by the physical port on the router into which you are plugging the modem (e.g., “USB
Port 2”).
• Manufacturer – Select by the modem manufacturer (e.g., “Cradlepoint Inc.”)
• Model – Set your rule according to the specific model of modem
• Type – Select by type of Internet source (Ethernet, LTE, Modem, Wireless as WAN, WiMAX)
• Serial Number – Select a 3G or LTE modem by the serial number
• MAC Address – Select a WiMAX modem by MAC Address
• Unique ID – Select by ID. This is generated by the router and displayed when the device is connected
to the router.
•
Condition: Select “is,” “is not,” “starts with,” “contains,” or “ends with” to create your condition’s
statement.
Value: If the correct values are available, select from the dropdown list. You may need to manually input
the value.
•
Invert WAN Binding: Advanced option that inverts the meaning of WAN Binding to only establish this tunnel
when the specified WAN Binding device(s) are NOT connected.
Tunnel Enabled: Select to activate the tunnel.
Add/Edit Tunnel – Routes
Adding routes allows you to configure what types of network traffic from the local host or hosts will be
allowed through the tunnel.
Click Add Route to configure a new route. You will need to input the following information, defined by the
remote network:
•
•
Network Address – This is the network address that is the destination of the route. This should be set to
the network address at the remote side of the tunnel.
Netmask – This is the corresponding subnet mask of the network being defined (Default: 255.255.255.0).
You can set the tunnel to connect to a range of IP addresses or to a single IP address. For example, you could
input 192.168.0.0 and 255.255.255.0 to connect your tunnel to all the addresses of the remote network in
the 192.168.0.x range. Alternatively, you could select a single address by inputting that address along with a
Netmask of 255.255.255.255.
Add/Edit Tunnel – Keep Alive
GRE keep-alive packets can be enabled to be sent through the tunnel in order to monitor the status of the
tunnel and more accurately determine if the tunnel is alive or not.
GRE keep-alive packets may be sent from both sides of a tunnel, or from just one side.
Enabled: Select to enable GRE Keep Alive to continually send keep-alive packets to the remote peer.
Rate: Choose the length of time in seconds for each check (Default: 10 seconds. Range: 2 – 3600 seconds).
©2016 Cradlepoint. All Rights Reserved. | +1.855.813.3385 | cradlepoint.com
51
User Manual / AER2100
11/21/16
Retry: Select the number of attempts before
the GRE tunnel is considered down or up
(Default: 3. Range: 1 – 255).
Failover Tunnel and Failback Tunnel: Use these
settings to create two tunnels – one as the
primary tunnel and one as the backup tunnel.
To configure tunnel failover/failback, complete
the following steps:
1. Create two tunnels: one for primary and
one for backup. Make sure both tunnels
have Keep Alive enabled.
2. Choose one to be the primary tunnel. Open
the editor for this tunnel and make sure
Tunnel Enabled is selected. Then go to the
Keep Alive page. Under Failover Tunnel
select the other tunnel you have created.
3. Open the editor for the failover tunnel.
Make sure Tunnel Enabled is not selected. On the Keep Alive page, set the Failback Tunnel to your primary
tunnel.
NEMO
Network Mobility (NEMO) is an Internet standards track protocol defined in RFC 5177. The protocol allows
session continuity for every node in a mobile network as the network moves.
NOTE: NEMO requires a feature license not included with ECM Prime. Go to SYSTEM > Administration > Feature
Licenses to enable this feature.
NEMO requires a service provider, e.g. Verizon Wireless Private Network with DMNR (Dynamic Mobile Network
Routing). Your NEMO service provider will define many of the settings for your NEMO configuration.
Once you have a NEMO service provider and a valid feature license, add networks to the Networks Routed by
NEMO section by first clicking Add. In the popup window, input:
•
•
Network Address - This is the network address that is the destination of the route. This should be set to
the network address at the remote side of the tunnel.
Netmask - This is the corresponding subnet mask of the network being defined (Default: 255.255.255.0).
The Network Address and Netmask, or subnet
mask, together define a range of IP addresses
that comprise the local network you want
associated with the NEMO settings.
Network Mobility (NEMO) Settings
Enbable: Enable NEMO.
WAN: Select the WAN(s) to use for the NEMO
connection. An expression such as “Unique ID
is (any)” will allow NEMO to operate on any
WAN, whereas “Type is LTE” will limit NEMO
operation to the WAN(s) provided by any
connected LTE device(s).
©2016 Cradlepoint. All Rights Reserved. | +1.855.813.3385 | cradlepoint.com
52
User Manual / AER2100
11/21/16
With WAN: Register the NEMO connection simultaneous with its specified WAN connection becoming available.
If not checked, will only register the NEMO connection when needed.
Home IP Address and Home Netmask – These may be provided by your NEMO service provider. The IP address
is a placeholder, “dummy” address; any IP address can be used (1.2.3.4 is common).
Home Agent IP Address, Home Agent Password, and Home Agent SPI – Your home agent will be defined by your
NEMO service provider.
Renew Registration – The NEMO network regularly re-registers with the home agent (e.g., every 30 seconds).
Specify the number of seconds between each check-in.
MTU – Override the maximum transmission unit (MTU) of the NEMO tunnel. The TCP MSS (maximum segment
size) is automatically derived from the MTU. Leave blank to rely on Path MTU Discovery.
L2TP
Layer 2 Tunneling Protocol (L2TP) tunnels can be used to create a connection between two private networks.
NOTE: L2TP Tunnels require a feature license not included with ECM Prime. Go to SYSTEM > Administration >
Feature Licenses to enable this feature.
Once you have a valid feature license, click **Add** to create a new L2TP tunnel. Click **Edit** to make changes
to an existing tunnel.
Add/Edit Tunnel – General
•
•
•
•
•
Tunnel Name – Enter a name to uniquely
identify this tunnel
LNS address – Enter the IP Address of the
LNS (tunnel server) peer
MTU – Set the maximum transmission unit
(MTU) for the L2TP tunnel
MRU – Set the maximum receive unit (MRU)
to request from the tunnel peer. The MRU is
very similar to the MTU: MTU is for packets
sent and MRU is for packets received
Tunnel Enabled – Click to enable/disable this
tunnel. Default: Enabled.
Authentication
More authentication options and overrides are
available in the next section.
•
•
Username – Username for user-specific
authorization. Leave blank to disable.
Password – Shared secret (or password) used
to authenticate the associated Local and
Remote names.
Redial
•
Enabled – When this is selected, the tunnel will attempt to reconnect if disconnected.
©2016 Cradlepoint. All Rights Reserved. | +1.855.813.3385 | cradlepoint.com
53
User Manual / AER2100
11/21/16
Add/Edit Tunnel – Authentication
•
•
•
Remote Name – Authorization name specified
by and to the remote system as its identity,
sometimes a username or hostname. Leave
blank to match any.
Local Name – Authorization name specified by
and to the remote system as the local system
identity; sometimes a username or hostname.
Leave blank to match any.
Secret – Shared secret (or password) used to
authenticate the associated Local and Remote
names.
Overrides
Override Authentication methods/parameters.
With methods set to Allow the two ends of
the tunnel can negotiate a common scheme.
Sometimes this negotiation fails, or the
implementation on one end is incompatible with
the other. To solve those authentication issues,
enable the overrides as needed.
•
•
•
•
Authentication – Username for user-specific authorization. Leave blank to disable.
CHAP – Choose from Allowed, Refused, or Required.
PAP – Choose from Allowed, Refused, or Required.
Name – Override names used to authenticate the router. Leave empty to use the default.
Add/Edit Tunnel – Routes
Typically specific routes are unnecessary, but they can be added in this section if needed. You can add or
remove routes to be used to funnel packets through the tunnel.
•
•
Network Address – This is the network address that is the destination of the route. This should be set to
the network address at the remote side of the tunnel.
Netmask – This is the corresponding subnet mask of the network being defined.
©2016 Cradlepoint. All Rights Reserved. | +1.855.813.3385 | cradlepoint.com
54
User Manual / AER2100
11/21/16
ROUTING
STATIC ROUTES
Add a new static route to the IP routing table or edit/remove an existing route.
Static routes are used in networks with more than one layer, such as when there
is a network within a network so that packet destinations are hidden behind an
additional router. Adding a static route is a way of telling the router about an
additional step that packets will need to take to reach their destination.
Click Add to create a new static route.
IP Version: Select IPv4 or IPv6. Depending on your selection, you have different
options for defining the address range.
IP/Network Address or IPv6 Address: The IP address of the target network
or host. The IPv6 address field includes CIDR notation to declare a range of
addresses.
Netmask/Prefix: The Netmask, along with the IPv4 address, defines the network
the computer belongs to and which other IP addresses the computer can see in the same LAN. An IP address
of 192.168.0.1 along with a Netmask of 255.255.255.0 defines a network with 256 available IP addresses from
192.168.0.0 to 192.168.0.255.
Gateway or IPv6 Gateway: Specifies the next hop to be taken if this
route is used. A gateway of 0.0.0.0 implies there is no next hop, and
the IP address matched is directly connected to the router on the
interface specified: LAN or WAN.
Device: Select the network interface from the dropdown menu (e.g.
ethernet-wan). You can use this instead of defining the IP address,
especially in cases when the IP address is changing.
Metric: Set the numerical priority of the route. Lower numbers have
higher priority.
Allow Network Access: (Default: Deselected.) Some static routes
will need an IP Filter Rule via the Firewall to allow packets through
the route without being blocked. Selecting this option automatically
creates this IP Filter Rule. If the IP/Network Address falls outside the
LAN IP range, you probably need to select this option.
Distribute: Allow this static route to be distributed via a routing protocol (BGP, OSPF, RIP, RIPng).
POLICY ROUTING
Policy routing allows for the addition of routes which are only
evaluated when a certain set of conditions match. The evaluation
occurs before the main system routes and can override the primary
route table. If no policy route is matched, the lookup will fall back on
the primary route table instead.
Route Policies: Route Policies define a policy to route table mapping.
Any traffic matched by the policy will be routed according to the
specified route table. If no policy or no route is matched, the lookup
will use the primary route table instead. To add a route policy, click Add.
•
•
IP Version: Select the IP protocol version.
Source IP/Network Address
©2016 Cradlepoint. All Rights Reserved. | +1.855.813.3385 | cradlepoint.com
55
User Manual / AER2100
•
•
•
•
•
11/21/16
Source Netmask/Prefix
Destination IP/Network Address
Destination Netmask/Prefix
Incoming Device: Select the incoming device upon which this
policy will match. (optional)
Table: Select the route table to use for routing when this policy
is matched.
Route Tables: Static route tables to be used in policy route lookups.
In order for route tables defined here to take effect, a corresponding
Route Policy must be created. Note that route tables defined here
are not available for use in dynamic routing protocols. To add a
route, click Add.
•
•
•
•
•
•
•
IP Version: Select the IP protocol version.
IP/Network Address
Netmask/Prefix
Gateway
Device: Select the interface or enter null0 to install a black hole
route.
Metric: Set the route metric.
Allow Network Access: Some static routes will need an IP Filter
Rule added to allow packets to route without being blocked by the firewall. Clicking the check box will
automatically add this rule for you.
ROUTE FILTERS
Common route filters may be used by any of the routing protocols. When shown in selection UI, filter
names are prepended with a label to identify the type, i.e. al:AccessListName, pl:PrefixListName, and
rm:RouteMapName. Filter names must be unique across all filters, common and protocol-specific.
Route filter entries are processed in the order in which they appear in the grid. A match will apply the action
(permit or deny) specified for the entry and processing will stop. If a filter is referenced and no match is found,
the route is denied.
Access List: Allows packet filtering by IP address.
Prefix List: Works the same as an access list with the
addition of filtering by prefix length. If the IP Network
matches, the filter will match if the prefix length is less than
or equal to the ‘le’ value, or greater than or equal to the ‘ge’
value. ‘le’ and ‘ge’ are optional, if both are omitted the prefix
list acts as an access list.
Route Map: Provides a richer set of match conditions for
packet filtering than access or prefix lists, and allows policy
to be applied to a route via set actions.
•
•
•
•
Description: Displayed to help identify the route map.
Permit: Checking Permit will carry out the Set Actions
if the Match Conditions are met, and permit the
route. Clearing Permit will deny the route if the Match
Conditions are met.
Match Conditions: A set of conditions that define a match.
Set Actions: A set of actions that are triggered by a match.
©2016 Cradlepoint. All Rights Reserved. | +1.855.813.3385 | cradlepoint.com
56
User Manual / AER2100
11/21/16
Certain match conditions and set actions are protocolspecific. Referencing a protocol-specific route map from an
incompatible protocol will cause errors during operation that
prevent the routing protocol from starting.
•
•
OSPF-specific: metric-type.
BGP-specific: as-path, weight, comm-list, local-preference,
community, ext community.
A community is identified by a 32-bit value (e.g. 1234567890)
usually expressed as two 16-bit values separated by a colon
(e.g. 18838:722). A received or well-known community can be
referenced by its number (or number pair), while defining a
community list allows naming and refering to it by name.
Note certain well-known communities can be used by name
without definition: no-advertise (never advertise these
routes), no-export (don’t advertise beyond confederation
boundary), local-AS (don’t advertise to external peers),
internet (advertise to everyone), and none (used to clear any
community associated with a route).
BGP route filters are only used by the BGP protocol. Access
lists are prepended with ‘fl:’ when shown in selection UI.
Community lists are prepended with ‘cl:’. Filter names must be
unique across all filters, common and protocol-specific.
Route filter entries are processed in the order in which they
appear in the grid. A match will apply the action (permit or
deny) specified for the entry and processing will stop. If a
filter is referenced and no match is found, the route is denied.
Access List: The ip as-path access-list allows filtering by BGP as-path. The as-path value can be specified as a
regular expression (regex).
Community List: Allows filtering by community. In essence a community is a label which is attached to routes
learned from that community. Then that community or label can be used to select which policy(s) should be
applied to those routes.
©2016 Cradlepoint. All Rights Reserved. | +1.855.813.3385 | cradlepoint.com
57
User Manual / AER2100
11/21/16
BGP
The latest version of BGP (Border Gateway Protocol) is version 4. BGP-4 is one of the Exterior Gateway
Protocols and de facto standard of Inter Domain routing protocol. BGP-4 is described in RFC1771, A Border
Gateway Protocol 4 (BGP-4). BGP is a distance vector
routing protocol, and the AS-Path framework provides
distance vector metric and loop detection to BGP
RFC1930.
BGP Editor
•
Enabled: Click to enable/disable the policy. (Default:
enabled).
•
•
Name: Unique name of the policy.
Router-ID: This sets the router-ID of the BGP
process. The router-ID may be an IP address of the
router, but need not be – it can be any arbitrary 32bit number. However it *MUST* be unique within the
entire BGP domain to the BGP speaker: bad things
will happen if multiple BGP speakers are configured with the same router-ID.
Cluster ID: Specify the cluster ID, used if the BGP cluster has more than one route reflector.
ASN: The AS (Autonomous System) number is one of the essential elements of BGP.
View Name: Specify a view to exchange BGP routing information without adding to the kernel routing
table.
Distance: The Administrative Distance can be specified for each of External (EBGP), Internal (IBGP) and
Local routes, respectively. Defaults of 20, 200 and 200 will apply for any unspecified distance if any
distance is specified.
Maximum Paths: Maximum Paths can be set greater than 1 to allow multipath routing. This setting limits
the number of paths; resources will be allocated to the limit specified whether or not all paths are used.
The first field sets a limit for both EBGP and IBGP. If desired, a different limit can be applied just to IBGP
using the second field.
•
•
•
•
•
©2016 Cradlepoint. All Rights Reserved. | +1.855.813.3385 | cradlepoint.com
58
User Manual / AER2100
•
•
11/21/16
Multipath Relax: Select “relax” to allow multi-path routing to different ASNs.
Timers Keepalive/Hold: Keepalive interval is the time between keepalive messages sent to peers. Hold
time is the timeout after the last keepalive message until the peer is declared dead. The Keepalive interval
must be set in order to set the Hold time. All times are in seconds from 1 to 65535. Set to 0 or empty to
disable (default).
Networks Associated with ASN or IPv6 Networks Associated with ASN: To configure a BGP router, you need
an AS number. An AS number is an identification of autonomous system. BGP protocol uses the AS number for
detecting whether the BGP connection is internal one or external one. Use the IPv4 address and netmask or
IPv6 address with a CIDR notation prefix length to define the address range.
Neighbor Options or IPv6 Neighbor Options: Creates a new neighbor identified by remote ASN and IP address.
•
•
•
•
•
•
•
•
•
•
•
•
Peer Group: Optionally specify a peer group
for this neighbor. You can Bind to an existing
peer group or Define a new one. A neighbor
will inherit the properties from the peer group
to which it is bound. Properties specified in a
neighbor will override inherited properties.
IP Address: The IP address of the neighbor. Not
specified if this is a peer group definition.
Port: Specify port.
Remote ASN: Enter the ASN of the remote AS.
The AS (Autonomous System) number is one of
the essential elements of BGP. BGP is a distance
vector routing protocol, and the AS-Path
framework provides distance vector metric and
loop detection to BGP. RFC1930.
Weight: Assign a weight to a neighbor
connection.
Maximum Prefix: Specify the maximum number
of prefixes that a BGP routing process will
accept from the specified peer.
Password: Enable message digest5 (MD5)
authentication on a TCP connection between
BGP peers. The same password must be used on
both peers.
Update Source: Specify the IPv4 source address
or interface name to use for the BGP session to
this neighbor.
Default Originate: Allow the local router to send
the default route (0.0.0.0) to a neighbor for use
as a default route. Optionally, a route map can
be specified to conditionally inject the default
route.
Don’t Send Community: Unless this option is
selected, any defined communities attributes will be sent to the BGP neighbor.
eBGP Multihop: Accept and attempt BGP connections to external peers residing on networks that are not
directly connected. Mutually exclusive with TTL Security. Optionally specify Time To Live from 1 to 255
hops.
TTL Security: Specify the number of hops to reach eBGP neighbors. Mutually exclusive with eBGP Multihop.
©2016 Cradlepoint. All Rights Reserved. | +1.855.813.3385 | cradlepoint.com
59
User Manual / AER2100
•
•
•
•
•
•
•
•
•
•
•
11/21/16
Next Hop Self: Configure the router as the next hop for a BGP-speaking neighbor or peer group if it is
learned via eBGP. Select All to also apply this setting to routes learned via iBGP.
Local AS Number: Enter the AS Number used locally as this neighbor’s prefix. It is prepended to the
received AS_PATH when receiving routing updates from the peer, and prepended to the outgoing AS_PATH
when transmitting local routes to the peer. Check No Prepend to not prepend the local AS Number to either
the received or outgoing AS_PATH. Check Replace AS to prepend the local AS Number to just the outgoing
AS_PATH.
Distribute-list In/Out: Specify a distribute-list for the peer in either or both directions. Lists are chosen
from the collection of access lists and prefix lists defined in Route Filters, Common tab. Access list and
prefix list names are prepended with ‘al’ and ‘pl’, respectively.
Filter-list In/Out: Filter this neighbor’s incoming and/or outgoing advertisements according to the specified
as-path access list(s). Lists are chosen from the collection of as-path access lists defined in Route Filters,
BGP tab.
Prefix-list In/Out: Filter this neighbor’s incoming and/or outgoing advertisements according to the
specified prefix list(s). Lists are chosen from the collection of prefix lists defined in Route Filters, Common
tab.
Route Map In/Out: Apply a route map to incoming and/or outgoing routes. Maps are chosen from the
collection of route maps defined in Route Filters, Common tab.
Route Reflector Client: Configures the router as a BGP route reflector and configures the neighbor as its
client.
Capability Negotiation: Configure capability negotiation with the remote peer. Select Strict to completely
match capabilities. Select Disable to suppress sending a negotiation message to peers that are not
configured as IPv4 unicast. Select Override to ignore the remote peer’s capability value and use the local
value instead.
Soft Reconfiguration: Configure the router to store updates.
Advertisement Interval: Configure the interval for BGP routing updates, in seconds from 0 to 600.
Timers Keepalive/Hold: Keepalive interval is the time between keepalive messages sent to peers. Hold
time is the timeout after the last keepalive message until the peer is declared dead. The Keepalive interval
must be set in order to set the Hold time. All times are in seconds from 1 to 65535. Set to 0 or empty to
disable (default).
Redistribute Routes: Redistribute routes of the specified protocol or kind into BGP, with the metric type and
metric set if specified, filtering the routes using the given route map if specified. Redistributed routes may
also be filtered with distribute lists.
•
•
•
Type: The type is the source of the route. Select from: Main, Connected, Static, RIP, and OSPF.
Metric: Numerical priority of the route.
Route Map: Route maps provide a means to filter and/or apply actions to routes, allowing policies to be
applied to routes.
OSPF
OSPF (Open Shortest Path First) version 2 is a routing protocol described in RFC2328, OSPF Version 2. OSPF
is an IGP (Interior Gateway Protocol). Compared with RIP, OSPF can provide more scalable network support
and faster convergence times. OSPF is widely used in large networks such as ISP (Internet Service Provider)
backbone and enterprise networks. Click Add to add an OSPF router.
General
•
Enable: Enable and disable the routing protocol policy.
©2016 Cradlepoint. All Rights Reserved. | +1.855.813.3385 | cradlepoint.com
60
User Manual / AER2100
•
•
•
•
•
•
•
•
11/21/16
Router ID: OSPF routers are identified by a
unique ID which must be a dotted quad (like an IP
address). This ID MUST be unique within the entire
OSPF domain - errors will happen if multiple OSPF
speakers are configured with the same router-ID.
ABR Type: The OSPF standard does not allow
an ABR to consider routes through connected
non-backbone areas. Relaxed (default) relaxes
this restriction and will consider routes through
non-backbone areas if the backbone area is down.
Standard respects the OSPF standard regardless
if the backbone area is down. Shortcut will always
route through the best path even if it does not go
through the backbone area. When this is set, shortcut can be enabled/disabled on a per area basis.
Flags: RFC 1583 Compatibility uses the predecessor standard RFC 1583 path preference algorithm. This
typically is NOT set. Opaque capability enables forwarding Opaque LSA extensions described in RFC 5250.
Max Metric: Set this router to broadcast max (infinite-distance) metric. Essentially broadcasting that this
router is unreachable.
Passive Interface Default: By default, any interface that controls a defined OSPF network will send linkstate advertisements. Set Passive Interface Default to allow only interfaces configured under Interfaces to
send link-state advertisements.
Refresh Timer: Sets the OSPF LSA refresh timer. Default is 10 seconds.
Reference Bandwith (Mb/s): Sets the reference bandwidth for cost calculations. Link cost will
automatically scale in reference to this bandwidth unless explicitly overridden. The default is 100 Mb/s
equal to cost of 1. Note: this setting MUST be consistent across routers in the OSPF domain.
SPF Timers: Sets the shortest path first algorithm adaptive timers in milliseconds. Modifying these
values allows you to manage CPU usage when calculating SPF. Delay sets the initial delay. SPF calculations
will always be performed at least this many milliseconds apart. Consecutive SPF calculations will always
be separated by at least the Hold Time up to the Max Hold Time increasing by Max Hold Time for each
consecutive calculation.
Interfaces
•
•
•
•
•
•
Device: Select device interface.
Options: Set interface options. Passive means no
Hellos will be transmitted out this interface. MTU
Ignore disables MTU mismatch detection.
Network Type: Set the network type for this
interface.
Authentication: Set OSPF interface authentication.
Key sets the OSPF authentication key to a
simple password. After setting authentication
key, all OSPF packets are authenticated. The
authentication key has a maximum length of
eight characters if using plain text authentication
and sixteen characters if using message-digest
authentication. Key ID enables message-digest authentication. Leave this blank to enable plain text
authentication. The Key ID identifies the secret key used to create the message digest. This ID is part of
the protocol and must be consistent across routers on a link.
Cost: OSPF metric for this interface.
Transmit Delay: Link state transmit delay.
©2016 Cradlepoint. All Rights Reserved. | +1.855.813.3385 | cradlepoint.com
61
User Manual / AER2100
•
•
•
11/21/16
Priority: The router with the highest priority will be more eligible to become Designated Router. Setting
this to 0 disables this router from participating in DR elections.
Intervals: Set hello intervals. Hello sets the number of seconds for the Hello Interval timer value. Setting
this value, Hello packets will be sent every timer value seconds. This value must be the same for all routers
in the area. The default value is 10 seconds. Dead sets the number of seconds for the Router Dead Interval
timer value used for Wait Timer and Inactivity Timer. This value must be the same for all routers attached
an area. The default value is 40 seconds. Retransmit sets the number of seconds between retransmitting
lost link state advertisements.
Sub-second Hellos: Enable sub-second Hellos and set the number of Hellos per second. When set, Dead
Interval is set to one second.
Areas
•
•
•
•
•
•
•
Area: Areas are identified by a unique ID which
may be a 32-bit unsigned integer or a dotted quad
(like an IP address).
Default Cost: Set the cost of default-summary
LSAs announced to stubby areas.
Options: Set options for this area. Stub indicates
that this area is a stub and no area router will
propagate routes external to OSPF and ASExternal LSAs (Type-5s) or ASBR-Summary LSAs
(Type-4) will be propagated into the area. Only
Network-Summary (Type-3) and default-route summary advertisements will be propagated. Not-So-Stubby
indicates this area is Not-So-Stubby or NSSA. This is similar to a stubby area except external routes are
propagated as Type-7 LSAs. NSSA Type-7 NSSAs can optionally be configured to be translated to Type-5
LSAs with the NSSA Translate option set. No Summary Prevents ABR from injecting inter-area summaries
into the specified stub or Not-So-Stubby area. Default routes will be injected as a type 3 summary LSA.
NSSA Type 7-to-5 Translation: Method of translating Type-7 LSAs to Type-5 when propagating external
routes. Via Election indicates this router is an NSSA Border Router but other border routers exist in the
topology. It will perform Type-7 to Type-5 translation unless another border router has Always set or is set
to Via Election and has a higher router-id. Always indicates this is an NSSA Border Router and must always
perform Type-7 tp Type-5 LSA translations. Never indicates that this router must never perform Type-7 to
Type-5 LSA translations.
Shortcut: Enable or disable shortcuts through non-backbone areas. Default will shortcut only if the
backbone link is down. Requires that ABR Type be set to Shortcut.
Access-List Filter: Filter Type-3 summary LSAs to/from area using access lists. This is only applicable on
ABR.
Prefix-List Filter: Filter Type-3 summary LSAs to/from area using prefix lists. This is only applicable on
ABR.
Redistribute
•
•
Default Originate: Enable
broadcasting default route. Always
will cause the default route
(0.0.0.0/0) to be broadcast even if
it is not in the routing table. Metric
specifies the metric of the default
route. Metric Type is the OSPF metric
type (default Type-2). Route Map specifies an optional route map to filter routes.
Default Metric: Specify the default metric for routes redistributed to OSPF. This can be overridden under
the Redistribute configuration.
©2016 Cradlepoint. All Rights Reserved. | +1.855.813.3385 | cradlepoint.com
62
User Manual / AER2100
•
•
11/21/16
Default Distance: Sets the default administrative distance for intra-area, inter-area and external routes.
Specific distances can be set under Distances. The default is 110.
Distances: Specify administrative distances for intra-area, inter-area, or external routes. This overrides
the value set in Default Distance.
RIP
RIP (Routing Information Protocol) is a widely deployed interior gateway protocol. RIP is a distance-vector
protocol based on the Bellman-Ford algorithms. As a distance-vector protocol, RIP sends updates from
one router to its neighbors periodically, allowing the convergence to a known topology. In each update, the
distance to any given network will be broadcast to its neighboring router. The router supports RIP version 2 as
described in RFC2453 and RIP version 1 as described in RFC1058.
RIP Editor
•
•
•
•
•
•
•
•
•
Name: Unique name of the policy.
Metric: RIP metric is a value for distance for the
network. Usually RIP increments the metric when
the network information is received. The metric
for redistributed routes is set to 1.
Protocol Version: RIP can be configured to send
either version 1 or version 2 packets. The default
is to send RIPv2 while accepting both RIPv1
and RIPv2 (and replying with packets of the
appropriate version for REQUESTS / triggered
updates).
Password: RIPv2 allows packets to be
authenticated via either an insecure plain text
password, included with the packet, or a more
secure MD5 based HMAC (keyed-Hashing for Message AuthentiCation). RIPv1 cannot be authenticated at
all, so when authentication is configured RIP will discard routing updates received via RIPv1 packets.
Plain text password: Select to use a plain text password instead of an MD5 HMAC. WARNING: A plain text
password is insecure.
Enabled: Click to enable/disable the policy. (Default: enabled.)
Timers: Update specifies the period at which the routing table is sent to all neighbors. Default is 30
seconds. Timeout specifies the length of time that the route is valid. Default is 180 seconds. Garbage
specifies the garbage collection timer that triggers removal of the route from the routing table. Default is
120 seconds.
Offset list in: Offset-list adds the specified offset to the incoming and outgoing metric for routes matched
by the specified access-list. If the offset is 0, no action is taken.
Offset list out: Offset-list adds the specified offset to the incoming and outgoing metric for routes
matched by the specified access-list. If the offset is 0, no action is taken.
Networks: Set the RIP-enabled interfaces by
network. RIP is enabled on the interfaces that have
addresses within the network range.
Interfaces: Enable RIP on a specific interface. Useful
if the interface’s IP addresses are dynamic.
•
•
Device: Select network interface device.
Send version: Select the RIP version that will
be sent on this interface, overriding the global
setting. Version can be 1 or 2, or 0 to select both.
©2016 Cradlepoint. All Rights Reserved. | +1.855.813.3385 | cradlepoint.com
63
User Manual / AER2100
•
•
•
•
•
11/21/16
Receive version: Select the RIP version that will be accepted on this interface, overriding the global
setting. Version can be 1 or 2, or 0 to select both.
Passive: Select passive mode for the interface. In passive mode, RIP routing updates are accepted by, but
not sent out of, the interface.
No split horizon: Disable the split horizon mechanism. Enabling prevents RIP from advertising routes over
the interface on which they were learned.
Distribute Access-list In/Out: Specify access-lists that filter the incoming and outgoing distribution of RIP
routes.
Distribute Prefix-list In/Out: Specify prefix-lists that filter the incoming and outgoing distribution of RIP
routes.
Neighbors: When a neighbor doesn’t understand multicast, this command is used to specify neighbors. In some
cases, not all routers will be able to understand multicasting, where packets are sent to a network or a group
of addresses. In a situation where a neighbor cannot process multicast packets, it is necessary to establish a
direct link between routers. The neighbor command allows the network administrator to specify a router as a
RIP neighbor. The no neighbor a.b.c.d command will disable the RIP neighbor. Assign a neighbor by inputting an
IP address.
Redistribute Routes: Redistribute routes of the specified protocol or kind into RIP, with the metric type and
metric set (if specified), filtering the routes using the given route map (if specified). Redistributed routes may
also be filtered with distribute lists.
•
•
•
Type: The type is the source of the route. Select from: Main, Connected, Static, OSPF, BGP.
Metric: RIP metric is a value for distance for the network. Usually RIP increments the metric when the
network information is received. The metric for redistributed routes is set to 1.
Route Map: Route maps provide a means to filter and/or apply actions to routes, allowing policies to be
applied to routes.
RIPng
RIPng (RIP next generation) extends RIPv2 to support IPv6. See RIPng on Wikipedia and RFC 2080 for details.
RIPng Editor
•
•
•
Name: Unique name of the policy.
Metric: RIPng metric is a value for distance for the network. Usually
the RIP service increments the metric when the network information
is received. The metric for redistributed routes is set to 1.
Enabled: Click to enable/disable the policy. (Default: enabled.)
Networks: Set the RIPng-enabled interfaces by network using IPv6
addresses. RIPng is enabled on the interfaces that have addresses within
the network range.
Routes: Set RIPng static routing announcement of specified network
address.
Redistribute Routes: Redistribute routes of the specified protocol or kind
into RIPng, with the metric type and metric set if specified, filtering the routes using the given route-map if
specified.
•
•
Type: The type is the source of the route. Select from: Main, Connected, Static, OSPF, BGP.
Metric: RIPng metric is a value for distance for the network. Usually the RIP service increments the metric
when the network information is received. The metric for redistributed routes is set to 1.
©2016 Cradlepoint. All Rights Reserved. | +1.855.813.3385 | cradlepoint.com
64
User Manual / AER2100
•
11/21/16
Route Map: Route maps provide a means to filter and/or apply actions to routes, allowing policies to be
applied to routes.
QOS
When QoS (Quality of Service, also known as “Traffic Shaping”) is enabled, the router will control the flow of
Internet traffic according to the user-defined rules. In other words, Traffic Shaping improves performance by
allowing the user to prioritize applications.
Enable QoS: Click on this box to open options for controlling Internet traffic. You can assign maximum Upload
Speed and Download Speed values and define your own Traffic Shaping rules.
WAN Profile Speeds
Upload Speed and Download Speed: Setting the Upload
Speed and Download Speed is required to control traffic
flow accurately. Adjust the sliding bar to restrict the
maximum upload and/or download speed for the Internet
source(s) you are using. For example, you might restrict
the upload speed to prioritize available bandwidth for
download or to reduce overall bandwidth use in order to
lower costs. It is recommended that you experiment with
different values for your particular Internet connection
for best results.
NOTE: Upload speed is the speed at which data can be
transferred to your ISP. Download speed is the speed at
which data can be transferred to you from your ISP. You
can test your connection speeds with a service such as
speedtest.net.
Queues
Queues and rules work in conjunction
to prioritize bandwidth for the most
critical operations. Multiple rules can be
associated with one queue. Use rules to
associate your more critical operations
with queues that have higher
bandwidth settings. For example, you
might have two queues, one for “critical” and one for “secondary” with critical having most of the bandwidth
percentage. Use rules to associate your most important bandwidth needs (POS system, VoIP, etc.) with the
critical queue. Restrict the bandwidth available for less important functions with the secondary queue.
Assign percentages of both upload and download bandwidth to each queue. If you assign 80% download
bandwidth to the first queue, the next queue will be forced to be 20% or less.
Click Add to create a new Traffic Shaping/QoS queue.
Queue Name: Choose a name that is meaningful to you.
©2016 Cradlepoint. All Rights Reserved. | +1.855.813.3385 | cradlepoint.com
65
User Manual / AER2100
11/21/16
DSCP (DiffServ) Tag: Differentiated Services
Code Point (DSCP) is the successor to TOS (Type
of Service). Use this field to ‘tag’ the traffic by
putting the value in the DSCP header of each IP
packet that flows through this queue. Use the
value of ‘0’ to clear the existing DSCP value in the
packet header.
DSCP Tagging is sometimes used so that other
networking equipment, upstream or post-NAT,
can do traffic shaping based on the DSCP Tags as
opposed to IP addresses or ports.
This setting is optional.
Upload Bandwidth
Enable Upload QoS: (Default: Enabled.) Deselect
if you want your rule to apply to download
traffic only. Leave this selected to include upload
restrictions with this queue.
Borrow Spare Bandwidth: (Default: Enabled.)
When this is enabled, the interfaces/protocols associated with this rule will borrow unused bandwidth from
other rules. Disabling borrowing will restrict the traffic to the specified bandwidth. Higher priority queues will
be offered excess bandwidth first.
Upload Bandwidth: This is the percentage of the connected WAN upload bandwidth that will be reserved for
the specified traffic. The maximum value is adjusted to the remaining percentage after other rules receive
their share.
Upload Priority: The priority value has two different effects on traffic. Higher priority traffic is handled before
lower priority traffic, which can lead to shorter response times. Also, when spare bandwidth is available it is
offered to higher priority queues first. Move the slider to select from the following options (Default: Normal):
•
•
•
•
•
•
•
•
Lowest
Lower
Below Normal
Normal
Above Normal
High
Higher
Highest
Click Next to continue to the next page.
Download Bandwidth
Enable Download QoS: (Default: Enabled.) Deselect if you want your rule to apply to upload traffic only. Leave
this selected to include download restrictions with this queue.
Borrow Spare Bandwidth: (Default: Enabled.) When this is enabled, the interfaces/protocols associated with
this rule will borrow unused bandwidth from other rules. Disabling borrowing will restrict the traffic to the
specified bandwidth. Higher priority queues will be offered excess bandwidth first.
Download Bandwidth: This is the percentage of the connected WAN upload bandwidth that will be reserved for
the specified traffic. The maximum value is adjusted to the remaining percentage after other queues receive
their share.
©2016 Cradlepoint. All Rights Reserved. | +1.855.813.3385 | cradlepoint.com
66
User Manual / AER2100
11/21/16
Download Priority: The priority value has two different effects on traffic. Higher priority traffic is handled
before lower priority traffic, which can lead to shorter response times. Also, when spare bandwidth is available
it is offered to higher priority queues first. Move the slider to select from the following options (Default:
Normal):
•
•
•
•
•
•
•
•
Lowest
Lower
Below Normal
Normal
Above Normal
High
Higher
Highest
Click Finish to save this queue.
Rules
A traffic shaping rule identifies a specific message flow and assigns that flow to one of the queues created
above.
Click Add to create a new Traffic Shaping rule.
Traffic Shaping / QoS Rule Editor
The first page of the Traffic Shaping / QoS Rule Editor allows you enable/disable the rule, name the rule, specify
a protocol for the rule, and select a queue to associate the rule with.
Rule Enabled: (Default: Enabled.) Deselect
this to disable this rule. This can be useful for
quickly changing configurations. If both upload
QoS and download QoS are disabled then the
rule will disable automatically.
Rule Name: Create a name for the rule that is
meaningful to you.
Protocol: The protocol used by the messages:
TCP/UDP, TCP, UDP, or ICMP. Select “Any” if your
rule does not control a specific type of message
that uses a specific protocol.
Queue Name: Select a queue to associate this
rule with.
Click Next to continue to the next page.
Use ports and/or IP addresses to define the
type(s) of traffic attached to this rule. Leaving
any field blank will match all values; all fields
are optional.
Source Port(s) and/or Destination Port(s): Enter a port number between 1 and 65535. To enter a single port
number, input the number into the left box. To enter a range of ports, fill in both boxes separated by the colon.
For example “80:90” would represent all ports between 80 and 90 including 80 and 90 themselves.
Source IP Address, Source Netmask, Destination IP Address, and Destination Netmask: Specify an IP address or
range of IP addresses by combining an IP address with a netmask for either “source” or “destination” (or both).
©2016 Cradlepoint. All Rights Reserved. | +1.855.813.3385 | cradlepoint.com
67
User Manual / AER2100
11/21/16
Source vs. destination is defined by traffic flow.
Leave these blank to include all IP addresses
(such as if your rule is defined by a particular
port instead).
EXAMPLE: If you want to associate this rule
with your guest LAN, you could input the IP
address and netmask for the guest LAN here
(leaving the last slot “0” to allow for any user
attached to the guest network):
•
•
Source IP Address: 192.168.10.0
Source Netmask: 255.255.255.0
Application Set: Application sets can be
defined in the Application Sets tab of the
Firewall Configuration page. The application
identification might not take place until
multiple packets have already bypassed a rule.
Application sets require an active license to
exist on the device for them to function.
DSCP (DiffServ): Differentiated Services Code Point (DSCP) is the successor to TOS (Type of Service). Use
this field to select traffic based on the DSCP header in each IP packet. This field is sometimes set by latency
sensitive equipment such as VoIP phones. This setting is optional.
DSCP Negate: When checked this rule will match on any packet that does not match the DSCP field.
Click Finish to save this rule.
DNS SERVERS
DNS, or Domain Name System, is a naming system that translates between domain names (www.cradlepoint.
com, for example) and Internet IP addresses (206.207.82.197). A DNS server acts as an Internet phone book,
translating between names that make sense to people and the more complex numerical identifiers. The DNS
page for the device has these distinct functions:
•
•
•
•
DNS Settings: By default your router is set to automatically acquire DNS servers through your Internet
provider (Automatic). DNS Settings allows you to specify DNS servers of your choosing instead (Static).
Split DNS: Enable or disable the redirecting of specified domains to alternate DNS servers.
Dynamic DNS Configuration: Allows you to host a server (Web, FTP, etc.) using a domain name that you
have purchased (www.example.com) with your dynamically assigned IP address.
Known Hosts Configuration: Allows you to map a name (printer, scanner, laptop, etc.) to an IP address of a
device on the network.
DNS Settings
You have the option to choose specific DNS servers for your network instead of using the DNS servers
assigned by your Internet provider. The default DNS servers are usually adequate. You may want to assign DNS
servers if the default DNS servers are performing poorly, if you want WiFi clients to access DNS servers that
you use for customized addressing, or if you have a local DNS server on your network.
Mode: Automatic or Static (default: Automatic). Switching to “Static” enables you to set specific DNS servers in
the Primary DNS and Secondary DNS fields.
©2016 Cradlepoint. All Rights Reserved. | +1.855.813.3385 | cradlepoint.com
68
User Manual / AER2100
11/21/16
Primary DNS and Secondary DNS: If you choose
to specify your DNS servers, then enter the IP
addresses of the servers you want as your primary
and secondary DNS servers in these fields. The DNS
server settings will be pre-populated with public DNS
server IP addresses. You can override the IP address
with any other DNS server IP address of your choice.
For example, Google Public DNS servers have the IP
addresses 8.8.8.8 and 8.8.4.4 while 4.2.2.2 and 4.2.2.3
are servers from Level 3 Communications.
Force All DNS Requests To Router: Enabling this will redirect all DNS requests from LAN clients to the router’s
DNS server. This will allow the router even more control over IP addresses even when clients have their own
DNS servers statically set.
Split DNS
Split DNS allows you create two zones for the same
domain, one to be used by the internal network, the
other used by the external network. Split DNS directs
internal hosts to an internal domain name server for
name resolution and external hosts are directed to an
external domain name server for name resolution.
Primary Split DNS and Secondary Split DNS: If you
choose to specify your DNS servers, then enter the IP
addresses of the servers you want as your primary and secondary DNS servers in these fields. The Secondary
DNS is optional.
Domain: Click Add to add desired domain for Split DNS.
Dynamic DNS Configuration
The Dynamic DNS feature allows you to host a
server (Web, FTP, etc.) using a domain name that
you have purchased (www.yourname.com) with your
dynamically assigned IP address. Most broadband
Internet Service Providers assign dynamic (changing)
IP addresses. When you use a Dynamic DNS service
provider, you can enter your host name to connect to
your server, no matter what your IP address is.
•
•
•
Enable Dynamic DNS: Enable this option only if
you have purchased your own domain name and
registered with a Dynamic DNS service provider.
Server Type. Select a dynamic DNS service
provider from the dropdown list:
• DynDNS
• DNS-O-Matic
• ChangeIP
• NO-IP
• Custom Server (DynDNS clone)
Custom Server Address. Only available if you select Custom Server from the Server Address dropdown list.
Enter your custom DynDNS clone server address here. For example: www.mydyndns.org.
©2016 Cradlepoint. All Rights Reserved. | +1.855.813.3385 | cradlepoint.com
69
User Manual / AER2100
•
•
•
•
11/21/16
Use HTTPS: Use the more secure HTTPS
protocol. This is recommended, but can be
disabled if not compatible with the server.
Host name: Enter your host name, fully
qualified. For example: myhost.mydomain.net.
User name: Enter the user name or key
provided by the dynamic DNS service provider.
If the dynamic DNS provider supplies only a
key, enter that key for both the User name and
Password fields.
Password: Enter the password or key provided by the dynamic DNS service provider.
Advanced Dynamic DNS Settings
Update period (hours): (Default: 576) The time between periodic updates to the dynamic DNS, if your dynamic
IP address has not changed. The timeout period is entered in hours so valid values are from 1 to 8760.
Override External IP: The external IP is usually configured automatically during connection. However, in
situations where the unit is within a private network behind a firewall or router, the network’s external IP
address will have to be manually configured in this field.
You may find out what your external IP address is by going to http://myip.dnsomatic.com in a web browser.
Known Hosts Configuration
The Known Hosts Configuration feature allows you to map a name (printer, scanner, laptop, etc.) to an IP
address of a device on the network. This assigns a new hostname that can be used to conveniently identify a
device within the network, such as an office printer.
Click Add to name a device in your network.
Fill in the following fields:
•
•
Hostname: Choose a name that is meaningful to you. No spaces are allowed in this field.
IP address: The address of the device within your network.
EXAMPLE: a personal laptop with IP address 192.168.0.164 could be assigned the name “MyLaptop.”
Since the assigned name is mapped to an IP address, the device’s IP address should not change. To ensure that
the device keeps the same IP address, go to NETWORKING > Local Networks > DHCP Server and reserve the IP
address for the device by selecting the device in the Active Leases list and clicking Reserve.
WIFI AS WAN
WiFi as WAN uses an outside WiFi network as its Internet source. When WiFi as WAN is enabled, the router
will find other WiFi networks that you can select and connect to. Unless a selected WiFi source is on an
unprotected network, you will need to know its password or key.
To enable WiFi as WAN, first select the desired WiFi radio:
•
•
WiFi Radio #1 (2.4 GHz)
WiFi Radio #2 (5 GHz)
All Cradlepoint routers and some other routers use the same default IP address for the primary network:
192.168.0.1. If you attempt to set up WiFi as WAN and there is an “IP conflict,” you need to change the IP
address. The router is attempting to use the same IP address for both WAN and LAN, which is impossible. Go to
©2016 Cradlepoint. All Rights Reserved. | +1.855.813.3385 | cradlepoint.com
70
User Manual / AER2100
11/21/16
Network Settings > WiFi / Local Networks.
Select the network and click Edit. You can
change the IP address under IPv4 Settings.
For example, you might change 192.168.0.1 to
192.168.1.1.
Saved Profiles
This is a list of WiFi networks that have
already been configured as WAN sources.
The router will attempt to connect to any of
these access points using the password you
have configured. If more than one access
point is in range, then the router will connect
with the highest priority network.
Network: The name (SSID, or Service Set
Identifier) that is broadcast by the access
point.
BSSID: The numeric ID of the network (Basic
Service Set Identifier). This parameter is required when trying to connect to a hidden network using WiFi as
WAN. It is optional when connecting to a visible network. If it is set in a profile, both the SSID and BSSID must
match to connect to an access point. If the BSSID is not set in a profile, then the router will connect to any
access point that matches the given SSID.
Auth Mode: The type of encryption that is used by the network.
•
•
•
•
•
•
•
None
WEP Auto
WEP Open
WEP Shared
WPA1 Personal
WPA2 Personal
WPA1 & WPA2 Personal
You have two options for adding network profiles:
•
•
Automatic – Select a WiFi network in Site Survey and click Import
Manual – Click on Add under Saved Profiles and input the required information.
Site Survey
This is a list of WiFi networks that the router
can currently find, along with information
about the network such as its mode and
channel. Click “Refresh” if a WiFi network you
want to connect to is not listed. You can sort
the list based on any of the fields by clicking
on the field name.
If you import a network from Site Survey,
most of the information about the network
will already be completed. You need to input
the password (if there is one) and then click
submit to save the WiFi as WAN profile.
©2016 Cradlepoint. All Rights Reserved. | +1.855.813.3385 | cradlepoint.com
71
User Manual / AER2100
11/21/16
Wireless Scan Settings
Scan Interval: How often WiFi as WAN scans
the environment for updates. (Default: 60
seconds. Range: 5–3600 seconds.)
Scan While Connected: Continue to scan
for WiFi as WAN profile updates when
connected. Each time a scan occurs the
wireless communication of the router will be
temporarily interrupted. Normally this should
be disabled.
WAN AFFINITY
WAN Affinity rules allow you to manage traffic in your network so that particular bandwidth uses are
associated with particular WAN sources. This allows you to prioritize bandwidth.
EXAMPLE: You could specify that your guest LAN is only associated with your Ethernet connection with no
failover. Then if your Ethernet connection goes down and the embedded modem connects for failover for your
primary LAN, your guest LAN will not take bandwidth from your primary LAN, saving you money.
Click Add to open the WAN Affinity Policy Editor
and create a new WAN Affinity rule.
Name: Give a name for your rule that is meaningful
to you.
DSCP (DiffServ): Differentiated Services Code
Point is the successor to TOS (Type of Service).
Use this field to select traffic based on the DSCP
header in each IP packet. This field is sometimes set by latency sensitive equipment such as VoIP phones. If
you know specific DSCP values, you can input one here.
DSCP Negate: When checked this rule will match on any packet that does NOT match the DSCP field.
Protocol: Select from the dropdown list to
specify the protocol for a particular data use.
Otherwise, leave “Any” selected.
•
•
•
•
•
•
•
Any
ICMP
TCP
UDP
GRE
ESP
SCTP
Source IP Address, Source Netmask, Destination
IP Address, and Destination Netmask: Specify
an IP address or range of IP addresses by
combining an IP address with a netmask for
either “source” or “destination” (or both). Source
©2016 Cradlepoint. All Rights Reserved. | +1.855.813.3385 | cradlepoint.com
72
User Manual / AER2100
11/21/16
vs. destination is defined by traffic flow. Leave these blank to include all IP addresses (such as if your rule is
defined by a particular port instead).
EXAMPLE: If you want to associate this rule with your guest LAN, you could input the IP address and netmask
for the guest LAN here (leaving the last slot “0” to allow for any user attached to the guest network):
•
•
Source IP Address: 192.168.10.0
Source Netmask: 255.255.255.0
Failover: (Default: Selected.) When this is selected and traffic from the chosen WAN device for this rule is
interrupted, the router will fail over to another available WAN device. Deselect this option to restrict this
traffic to only the selected WAN interface.
When
Condition
Value
Port
Is
USB Port 1
Type
Is not
WiMax
•
When:
•
•
•
•
•
•
•
•
•
Port – Select by the physical port on the router that you are plugging the modem into (e.g., “USB Port
2”).
Manufacturer – Select by the modem manufacturer (e.g., “Cradlepoint Inc.”).
Model – Set your rule according to the specific model of modem.
Type – Select by type of Internet source (Ethernet, LTE, Modem, Wireless as WAN, WiMAX).
Serial Number – Select a 3G or LTE modem by the serial number.
MAC Address – Select from a dropdown list of attached devices.
Unique ID – Select by ID. This is generated by the router and displayed when the device is connected
to the router.
Condition: Select “is,” “is not,” “starts with,” “contains,” or “ends with” to create your condition’s
statement.
Value: If the correct values are available, select from the dropdown list. You may need to manually input
the value.
Load Balance Algorithm: Select the Load Balance Algorithm for this WAN Affinity rule from the following
dropdown options:
•
•
•
•
Round-Robin: Evenly distribute each session to the available WAN connections.
Rate: Distribute load based on the current upload and download rates. A WAN device’s upload and
download bandwidth values can be set in CONNECTION MANAGER.
Spillover: This was the default algorithm in older (version 3) firmware. Load is always given to devices with
the most available bandwidth. The estimated bandwidth rate is based on a combination of the upload and
download configuration values and the observed capabilities of the device.
Data Usage: This mode works in concert with the Data Usage feature. The router will make a best effort to
keep data usage between interfaces at a similar percentage of the assigned data cap in the data usage rule
for each interface, rather than distributing sessions based solely on bandwidth. For proper functioning you
need to create data usage rules for each WAN device you will be load balancing. Make certain to select the
“Use with Load Balancing” checkbox in the data usage rule editor.
©2016 Cradlepoint. All Rights Reserved. | +1.855.813.3385 | cradlepoint.com
73
User Manual / AER2100
11/21/16
CLIENT DATA USAGE
Client Data Usage displays upload and download
traffic for each LAN client. Click Enable Client Data
Usage Monitoring Service to begin tracking this
information. This data is not retained between
router reboots.
For each client this shows: Name, IP address, MAC
address, amount of data uploaded (MB), amount of
data downloaded (MB), and when traffic was last
sent or received for that client (“Last Traffic”).
The names that are shown are received during a DHCP exchange. If a client disconnects and reconnects with a
new IP address there will be an additional entry in this list.
Pressing Reset Statistics will restart all counters at 0.
NHRP
Next Hop Resolution Protocol is a protocol
used to discover addresses of clients on
Non-Broadcast Multiple Access (NBMA)
networks. It is used to create nextgeneration VPN technologies that allow
shortcutting between spokes. With NHRP,
systems attached to an NBMA network
dynamically learn the NBMA address of
the other systems that are part of that network, allowing these systems to directly communicate without
requiring an intermediate hop.
NOTE: NHRP Configuration requires a feature license not included with ECM Prime. Go to SYSTEM >
Administration > Feature Licenses to enable this feature.
The NHRP Supported Interfaces table displays the following fields for each configured NHRP interface:
•
•
•
•
Name: Name of the GRE tunnel that NHRP will use
Protocol Address/Prefix: GRE tunnel endpoint mapping that NHRP associates with the NBMA server
NBMA Address: NBMA server address the protocol address/prefix is associated with
Flags:
•
•
•
•
SD: Shortcut-Destination
N: Non-Caching
S: Shortcut
R: Redirect
Click Add to create a new NHRP interface.
•
•
•
Enabled: Enable or disable the interface.
Name: Give the interface a unique name that matches the mGRE (multipoint GRE) tunnel. Select from
configured GRE tunnels or input manually.
Peer Authentication: Embeds the secret plaintext password to outgoing NHRP packets. Incoming NHRP
packets on this interface are discarded unless this password is present. Max length: eight characters.
©2016 Cradlepoint. All Rights Reserved. | +1.855.813.3385 | cradlepoint.com
74
User Manual / AER2100
•
•
•
•
•
•
11/21/16
Holding Time: Specifies the holding time for
NHRP registration requests and resolution
replies.
Shortcut-Destination: Reply with
authoritative answers on NHRP resolution
requests destined to addresses in this
interface (instead of forwarding the packets).
Non-Caching: Disables caching of peer
information from forwarded NHRP resolution
reply packets.
Shortcut: Enable creation of shortcut routes.
Redirect: Enable sending of proprietary
enterprise-style NHRP traffic indication
packets.
Multicast: Determines how multicast
packets should be forwarded through NHRP
interfaces.
• NHS: Multicast packets will be forwarded
to each statically configured next hop
server. This is default and is typical for
the configuration of an NHRP spoke.
• Dynamic: Multicast packets will be forwarded to each connected peer. This is typically used for an
NHRP hub.
You also have the option to create static mappings for this interface. Click Add in the table to open the static
mapping editor.
•
•
•
•
•
Protocol Address: Mapped endpoint to from protocol address to NBMA address
Protocol Prefix: Optional prefix for protocol address
NBMA Address: Destination mapped address from protocol address/prefix
Register: This optional parameter specifies that a Registration Request should be sent to this peer on
startup (displays flag R in the static mapping table if selected)
Proprietary OS: This should be enabled if the statically mapped peer is running proprietary OS (displays flag
C in the static mapping table if selected).
©2016 Cradlepoint. All Rights Reserved. | +1.855.813.3385 | cradlepoint.com
75
User Manual / AER2100
SECURITY
11/21/16
IDENTITIES
Identities are reusable groups of items that are added to filter policy rules. A
match on any single item in the group will cause the rule to match. Identities are
referenced in rules by their name. Choosing descriptive names like “NW Sales
Team” or “Engineering” will aid in understanding existing rules and in choosing
identities for new rules.
HOST ADDRESSES
A Host identity can contain IPv4, IPv6, and Fully Qualified Domain Name
addresses. A single identity can contain a combination of IPv4 and IPv6
addresses. IPv4/6 addresses cannot be combined with FQDN addresses in the
same identity.
IP addresses are entered using CIDR notation, e.g. 1.2.3.4/32 and
0123:4567::CDEF/128. FQDN addresses are entered with at least one dot
separating a top-level domain from a root zone, e.g. cradlepoint.com.
To add a Host Address Identity, click Add.
PORTS
A port identity member can be entered as a single Start port number or as a port range by entering both a
Start and End port number.
To add a Port Identity, click Add.
MAC ADDRESSES
MAC addresses are entered in the form aa:bb:cc:dd:ee:ff.
To add a MAC Address Identity, click Add.
REPUTATION
A reputation file contains a list of IPv4 and IPv6 addresses and networks with CIDR notation, one address
or network per line. Reputation identity allows you to upload a file from a reputation service provider (e.g.,
www.spamhaus.org/drop/). It also provides a way to maintain large lists of IPs that need firewall attributes
applied to them. Files should be in the format where each line starts with an IP address or IP network and
prefix length. All other lines are rejected. Currently we support adding 65535 IPs per reputation identity.
To add a Reputation Identity, click Add, then select and upload your file.
APPLICATION SETS
An Application Set is a selection of possible application identifications that can be matched against in Zone
Firewall policies.
To add an Application Set Identity, click Add.
©2016 Cradlepoint. All Rights Reserved. | +1.855.813.3385 | cradlepoint.com
76
User Manual / AER2100
11/21/16
ZONE FIREWALL
ZONE DEFINITION
A Zone is a group of network interfaces. By default all interfaces within
a zone are allowed to initialize network communication with each other,
however any network traffic initialized outside of a zone to the interfaces
within the zone will be denied.
To add a zone, click Add.
FILTER POLICIES
A Filter Policy is a one-way filter applied to initialized network traffic flowing from one zone to another. A
Filter Policy needs to be assigned to a Forwarding for it to take effect. Filter Policies can either be Added,
Edited, or Removed.
•
•
Default Allow All is a preconfigured policy to
allow all traffic initialized from one zone to flow
to another zone. The state of the connection is
tracked to allow responses to traverse the zones
back to the source. LAN to WAN forwardings use
this policy by default. The policy can be removed or
altered to filter the traffic flow.
Default Deny All is a preconfigured policy to deny
all traffic initialized from one zone to be blocked
to another zone. WAN to LAN forwardings use this
policy by default. The policy can be removed or
altered to filter the traffic flow.
Click Add to create a new filter policy, or select an
existing policy and click Edit to open the filter policy
editor.
•
•
•
Name: Create a name meaningful to you.
Action: Choose either Allow or Deny. This is the action taken by the firewall if none of the filter policy rules
match the traffic being filtered.
Log: When checked, every rule in the policy will log matching packets as if the rule’s Log option had been
selected.
Click Add to create a new rule for this filter policy, or select an existing rule and click Edit to open the Rule
Editor.
•
•
•
•
•
Name: Create a rule name meaningful to you.
Action: Choose either Allow or Deny. This is the action taken by the firewall if the rule criteria match the
traffic being filtered.
Log: When checked, each packet matching this filter rule will be logged in the System Log.
IP Version: Select the IP version to match.
Enter match criteria under Source, Destination, Protocols and Application Sets.
©2016 Cradlepoint. All Rights Reserved. | +1.855.813.3385 | cradlepoint.com
77
User Manual / AER2100
•
•
•
•
11/21/16
Source: Select defined identities or enter
individual criteria for the appropriate Host, Port
and MAC address columns to match the source of
the traffic.
• Host: Enter an IP address or select a host
identity.
• Port: Enter a port, port range, or select a port
identity.
• MAC: Enter a MAC address or select a MAC
address identity.
Destination: Select defined identities or enter
individual criteria for the appropriate Host,
Port and MAC address columns to match the
destination of the traffic. See Source for the
column definitions.
Protocols: Select protocols (such as TCP, UDP, GRE, etc) from the defined list or enter a numeric code
for other protocols to match traffic of that protocol.
Application Sets: Select the defined application set or sets to match traffic related to those sets.
ZONE FORWARDING
Forwardings define how Filter Policies affect traffic
flowing between zones in one direction. Simply configure
the Source Zone, Destination Zone, and Filter Policy to
define a Forwarding. Forwardings can be Added, Edited,
Removed, or Toggled. Toggling a Forwarding will either
enable or disable the Forwarding.
Source and Destination zones are chosen from the list of
Zone Definitions. In addition, two special zones can be selected for forwarding endpoints:
•
•
The All zone will match any traffic handled by the router and is used as an endpoint for IP Filter
Rules migrated from previous firmware versions. User editable zones are preferred when adding new
forwardings.
The Router zone will match any traffic initialized from or directed to router services and can be used
to filter router service traffic. An example of traffic initialized by a router service would be the ECM
Management service. An example of traffic destined to a router service would be the SNMP service.
OPTIONS
Firewall Options
•
•
Anti-Spoof: Anti-Spoof checks help protect against malicious users faking the source address in packets
they transmit in order to either hide themselves or to impersonate someone else. Once the user has
spoofed their address they can launch a network attack without revealing the true source of the attack or
attempt to gain access to network services that are restricted to certain addresses.
Log Web Access: Enable this option to create a syslog record of web (IP port 80) access. Each entry will
contain the the IP address of the server and the client. Note that this may create a lot of log entries,
especially on a busy network. Sending the system log to a syslog server is recommended.
Application Gateways
Enabling an application gateway makes pinholes thru the firewall. This may be required for some applications
to function, or for an application to improve functionality or add features.
©2016 Cradlepoint. All Rights Reserved. | +1.855.813.3385 | cradlepoint.com
78
User Manual / AER2100
11/21/16
NOTE: Exercise caution in enabling application gateways as they impact the security of your network.
•
•
•
•
•
PPTP: For virtual private network access using Point to Point Tunneling Protocol.
SIP: For Voice over IP using Session Initiation Protocol.
TFTP: Enables file transfer using Trivial File Transfer Protocol.
FTP: To allow normal mode when using File Transfer Protocol. Not needed for passive mode.
IRC: For Direct Client to Client (DCC) transfer when using Internet Relay Chat. You may wish to forward TCP
port 113 for incoming identd (RFC 1413) requests.
DMZ (Demilitarized Zone)
A DMZ host is effectively not firewalled in the sense that any computer on the Internet may attempt to
remotely access network services at the DMZ IP address. Typical uses involve running a public web server,
supporting older games, or sharing files.
NOTE: As with port forwarding, caution should be used when enabling the DMZ feature as it can threaten the
security of your network.
NETWORK PREFIX TRANSLATION
Network Prefix Translation is used in IPv6 networks to translate one IPv6 prefix to another. IPv6 prefix
translation is an experimental specification (RFC 6296) trying to achieve address independence similar to NAT
in IPv4. Unlike NAT, however, NPT is stateless and preserves the IPv6 principle that each device has a routable
public address. But it still breaks any protocol embedding IPv6 addresses (e.g. IPsec) and is generally not
recommended for use by the IETF. NPT can help to keep internal network ranges consistent across various IPv6
providers, but it cannot be used effectively in all situations.
The primary purpose for Cradlepoint’s NPT implementation is for failover/failback and load balancing setups.
LAN clients can potentially retain the original IPv6 lease information and may experience a more seamless
transition when WAN connectivity changes than if not utilizing NPT.
Mode:
•
•
•
•
None – No translation is performed
Load Balance Only – (Default) Only translate networks when actively load balancing
First – Use the first IPv6 prefix found
Static – Always use a static IPv6 translation (input the prefix here)
Transitioning from short prefix to a longer prefix (such as from /48 to /64) is not without problems, as some of
the LANs may lose IPv6 connectivity.
REMOTE ACCESS RESTRICTION
Add any IPv4 addresses that need access to remote administration to this list. Clicking Add will allow the
addition of IP address and netmask pairs to the administration filter. Edit will allow you to change settings for
the selected address. Remove will remove a selected entry.
PORT FORWARD & PROXY
A port forwarding rule allows traffic from the Internet to reach a computer on the inside of your network. For
example, a port forwarding rule might be used to run a Web server.
NOTE: Exercise caution when adding new rules as they impact the security of your network.
Click Add to create a new port forwarding rule, or select an existing rule and click Edit.
©2016 Cradlepoint. All Rights Reserved. | +1.855.813.3385 | cradlepoint.com
79
User Manual / AER2100
11/21/16
Add/Edit Port Forwarding Rule
•
•
•
•
•
•
•
Name: Name your rule.
Enabled: Toggle whether your rule is
enabled. Selected by default.
Use Port Range: Changes the selection
options to allow you to input a range of
ports (if desired).
Internet Port(s): The port number(s) as
you want it defined on the Internet.
Typically these will be the same as
the local port numbers, but they do
not have to be. These numbers will be
mapped to the local port numbers.
Local Computer: Select the IP address
of an attached device from the dropdown menu, or manually input the IP address of a device.
Local Port(s): The port number(s) that corresponds to the service (Web server, FTP, etc.) on a local
computer or device. For example, you might input “80” in the Local Port(s) field to open a port for a Web
server on a computer within your network. The Internet Port(s) field could then also be 80, or you could
choose another port number that will be used across the Internet to access your Web server. If you choose
a number other than 80 for the Internet
Port, connections to that number will
be mapped to 80 – and therefore the
Web server – within your network.
Protocol: Select from the following
options in the dropdown menu:
•
•
•
TCP
UDP
TCP & UDP
Click Save to save your completed port
forwarding rule.
Port Proxying Rules
A port proxying rule allows traffic from the local LAN to be redirected to a specific computer/IP address on the
Internet.
Click Add to create a new port proxying rule, or select an existing rule and click Edit.
Add/Edit Port Proxying Rule
•
•
•
•
•
Name: Name your rule.
Enabled: Toggle whether your rule is
enabled. Selected by default.
Use Port Range: Check this box
to create a rule which proxies a
contiguous range of ports instead of
a single port. The remote port(s) will
require the same number of contiguous
ports.
Local Port(s): Specify the IP port(s) on
the LAN to proxy to a remote computer.
Remote Computer: Specify the remote
computer to receive proxied traffic.
©2016 Cradlepoint. All Rights Reserved. | +1.855.813.3385 | cradlepoint.com
80
User Manual / AER2100
•
•
11/21/16
Remote Port(s): Specify the IP port (first if a range) on the remote computer to receive proxy traffic.
Protocol: Select the IP protocol traffic to proxy from the following options in the dropdown menu:
•
•
•
TCP
UDP
TCP & UDP
Click Save to save your completed port proxying rule.
NAT
Zone NAT is similar to Port Forwarding and provides that functionality by mapping ports available on interfaces
associated with the Zone to ports available on local clients. Zone NAT also has the ability to map many types
interfaces selectable via a Zone. For example, GRE interfaces can be used to port forward traffic from the GRE
endpoints to local client thereby limiting exposure to the
local LAN while still gaining the benefits of GRE.
Click Add to create a Zone NAT.
•
•
•
•
•
•
Source Zone Name: The Zone created in Zone Firewall.
Select the Zone to NAT.
Original Destination IP: Specify which inbound traffic to
this router will have the destination IP translated to an
internal network.
Inbound Port(s): Specify the IP port(s) on the inbound
traffic to forward to a local computer.
Local Computer: Specify the local computer to receive
forwarded traffic.
Local Port(s): Specify the IP port (first if a range) on the
local computer to receive forwarded traffic.
Protocol: Select the IP protocol traffic to forward.
Dynamic 1:1 NAT
Dynamic NAT allows translating the destination ip of
incoming network traffic to a local network. All ports and
protocols will be forwarded. Netmasks should generally
match. If the local network range is larger than the incoming
destination range then network traffic will begin using
port overloading. One-to-One NAT can be accomplished by
specifying a host address or a /32 cidr address.
Click Add to create a Dynamic 1:1 NAT.
©2016 Cradlepoint. All Rights Reserved. | +1.855.813.3385 | cradlepoint.com
81
User Manual / AER2100
11/21/16
CONTENT FILTERING
WEBFILTER SETTINGS
General Settings
Enbable Webfilter: Selecting “Enable Webfilter” will enable the webfiltering
service. This is used to enable or disable all router-based webfiltering and
forwarding.
Filter HTTPS: Selecting “Filter HTTPS” enables redirection of all port 443
traffic into the proxy. The proxy will then extract the host name from
the SNI (Server Name Indication). If SNI is unavailable then the original
destination IP address is used for filtering. No decoding of the SSL/TLS
session is done.
Upstream Proxy Settings
Enabled: Select whether the use of an Upstream Proxy
server is enabled.
Proxy Address: The Proxy Address is the address the desired
HTTP proxy is hosted at. Addresses can be input as host
names or as ip addresses. If the proxy is unavailable HTTP
traffic will fail to cross the network and a notification page
will be shown.
HTTP Port: The port the HTTP Proxy is listening on.
HTTPS Port (Optional): The port for the proxy to forward
HTTPS traffic to. HTTPS is not transparently intercepted and
must have the LAN clients configured to use the Cradlepoint
router as a proxy for HTTPS to work properly.
MAC WEB FILTER RULES
MAC Address WebFilter Rules allow you to control
access from a specific MAC address to external
domains or websites. To add a rule, click Add.
•
•
•
•
•
MAC Address: Enter MAC Address.
Filter Action: Select Block or Allow.
Domain/URL/IP: Enter the Domain Name or
URL (address) of the website you wish to
control access for, e.g. www.google.com. To
make sure the full domain is blocked, enter
the most inclusive domain (e.g. google.com
will effectively block www.google.com as
well as maps.google.com and images.google.
com). Alternatively you can use an IP address,
e.g. 8.8.8.8, or address range written in CIDR
notation, e.g. 8.8.8.0/24.
Rule Priority: Higher number rules overrule
lower number rules.
Enabled: A rule can be enabled or disabled by
selecting or deselecting the checkbox.
Use MAC Address WebFilter Defaults together
with MAC Address WebFilter Rules to control website access for specific MAC addresses. By default, each MAC
©2016 Cradlepoint. All Rights Reserved. | +1.855.813.3385 | cradlepoint.com
82
User Manual / AER2100
11/21/16
address is allowed website access. Click Add/Edit
to change this setting for a MAC address.
Input the MAC Address and Default Action you
would like to apply to that MAC address.
Default Action: Select from the following
dropdown options:
•
•
Allow Access (default)
Block Access
When a network is set to Allow Access, it will
allow access to sites not specifically blocked in the
WebFilter Rules. When a network is set to Block
Access, it will block access to sites not specifically allowed in the WebFilter Rules.
NETWORK WEB FILTER RULES
Domain / URL filter rules allow you to control
access from your network to any external domain
or website. Rules are assigned to a specific LAN
network and the highest priority rule will have
precedence when there is a conflict. Addresses can
be added by URL/Domain name or by IP address.
IP address ranges can be filtered by using CIDR
notation, e.g. 4.2.2.2/24.
Exceptions to existing rules can be created by
adding another rule with higher priority. For
example if access to maps.example.com is desired,
but example.com is blocked with a priority of 50.
The addition of an allow rule for maps.example.
com with a priority of 49 or less will allow access.
When creating rules keep in mind that some sites
use multiple domains so each domain may need a
rule added to produce the desired behavior.
To add a Network Web Filter Rule, click Add.
Default Network Filter Settings
When a network is set to Allow (Blacklist) it will
allow access to those sites not blocked in the
Filter Rules. Selecting Block (Whitelist) will only
allow access to websites with an Allow action in
the Filter rules, all other sites will be blocked.
Selecting to Filter URLs by IP Address will cause
the router to perform a DNS lookup on URL entries
and the IP addresses will be appended to the
appropriate block/allow list. This can have side
effect of being very strict and sites that are hosted across many domains may need every domain added the list
for full functionality.
The settings can be changed by selecting a network and clicking the Edit button.
©2016 Cradlepoint. All Rights Reserved. | +1.855.813.3385 | cradlepoint.com
83
User Manual / AER2100
11/21/16
CLOUD-BASED FILTERING
Select a third-party Cloud Provider from the dropdown list.
•
•
•
Umbrella by OpenDNS
Zscaler Secure Web Gateway
Zscaler Internet Security
Umbrella by OpenDNS
Umbrella by OpenDNS is a cloud-based web filtering and security
solution that protects you online by filtering websites. Go to http://
www.opendns.com/business-security for information about Umbrella.
Enter your Umbrella account information in order to use these content
filtering settings.
OpenDNS ISP Filter Bypass Algorithm: It is possible that your Internet
Service Provider (ISP) uses the port that OpenDNS is configured to
access, port 53, which will prevent OpenDNS filtering. If OpenDNS does
not appear to be working correctly, enabling this will attempt to bypass
those ports when using an OpenDNS content filtering level.
Zscaler
Zscaler is a cloud-based web filtering and security provider that offers
several plan options. Depending on your Zscaler implementation, this
could include:
•
•
•
•
•
•
•
•
•
•
•
Global Cloud Platform
Real-Time Reporting
Behavioral Analysis
URL Filtering
Advanced Threat Protection
Inline Anti-Virus & Anti-Spyware
Web 2.0 Control
Data Loss Prevention
Bandwidth Management
Web Access Control
And more…
NOTE: Zscaler requires a feature license. Go to SYSTEM > Feature
Licenses to enable this feature.
Enter your Zscaler account information to enable these settings. Input
local network information (Network Address and Netmask) to assign
your Zscaler implementation to one or more local network(s).
©2016 Cradlepoint. All Rights Reserved. | +1.855.813.3385 | cradlepoint.com
84
User Manual / AER2100
11/21/16
THREAT MANAGEMENT
NOTE: Threat Management is only available for the AER family or Cradlepoint products, and requires a feature
license. Enable this feature through Enterprise Cloud Manager.
Cradlepoint Secure Threat Management leverages Trend Micro’s security experience and expertise in this
one-pass Deep Packet Inspection (DPI) solution. Threat Management includes settings for both IPS (intrusion
prevention system) and IDS (intrusion detection system), as well as application identification logging. Use
Threat Management to identify and prevent a wide variety of network threats.
This Threat Management solution examines network traffic for both signature matches from Trend Micro’s large
signature database of known threats and statistical anomalies to detect previously unknown threats. Trend
Micro regularly adds new signatures to its database: update your signature database version to ensure you’re
defending yourself against the newest threats. You have the option to update manually or schedule regular
updates.
Follow these steps to get started with Threat Management:
1. To purchase a license or to begin a free trial, log into Enterprise Cloud Manager (ECM) and go to the
Applications tab (this is only available to the primary account administrator). Once entitled, the router must
be rebooted for Threat Management to begin working.
2. Set up emailed or logged alerts in the Alerts tab in ECM.
3. Set up regularly scheduled signature updates in the configuration pages, or update manually in ECM via the
Devices or Groups page (click on Commands in the top toolbar and select Update IPS Signatures from the
dropdown options).
NOTE: Updating the signature database version causes a network disruption for a few seconds. You can schedule
these updates to occur during days/times when you expect less traffic on your network.
Status
The Status section shows if Threat Management is enabled.
It shows the current signature database version number, the
timestamp for the most recent update, and the status of the
most recent attempt to update signatures.
Click on the Update button to check for a new signature
database version.
Global Settings
Customize your Threat Management implementation (choose
between IPS and IDS, set up a signature update schedule,
etc.).
Operation Mode: Choose IPS, IDS, or neither.
•
•
•
Disabled
Detect and Prevent (default) – IPS mode
Detect Only – IDS mode
In both Detect and Prevent and Detect Only modes, detected packets are logged to the System Log as well as
sent to your ECM account.
Engine Failure/Error Action: In the unlikely event of an error with the Threat Management engine, you have the
following options:
•
•
Allow Traffic (default)
Deny Traffic
©2016 Cradlepoint. All Rights Reserved. | +1.855.813.3385 | cradlepoint.com
85
User Manual / AER2100
11/21/16
With Allow Traffic selected, the device will act like a typical router without Threat Management enabled and
route traffic as usual. If security is a huge concern, however, you may wish to select Deny Traffic to stop all
traffic when Threat Management isn’t working properly.
Application ID Logging: (Disabled by default.) The DPI engine can identify network traffic applications and send
this information to the system logs. Depending on your network traffic uses, application ID logging may send
huge amounts of data to the system logs. Cradlepoint recommends enabling a syslog server to manage this
information.
To view the logs, go to STATUS > System Logs. For configuration options, including syslog server setup, go to
SYSTEM > Administration > System Logging.
Signature Update Schedule
You can choose to have a different signature update
schedule for modems than for other WANs. This is
intended to protect against overages when data usage
limits for 3G/4G modems are restricted. For both NonModem WANs and Modem WANs, first choose the
Frequency for updates:
•
•
•
•
Never
Daily
Weekly
Monthly
Next, choose the specific day and time. These updates
cause a minor network disruption, so schedule updates for
times with less critical traffic.
Signature Settings
View a list of all signature categories, all signatures, or
signatures within a category.
By default, the Operation Mode is set under Global
Settings. To edit this for a category or a particular
signature, select a line in the table and click Edit. Choose
from the following:
•
•
•
Disabled
Detect and Prevent – IPS mode
Detect Only – IDS mode
©2016 Cradlepoint. All Rights Reserved. | +1.855.813.3385 | cradlepoint.com
86
User Manual / AER2100
11/21/16
CERTIFICATE MANAGEMENT
LOCAL CERTIFICATES
This is a table of local certificates, including certificate details.
• Name: Friendly description of the certificate.
• Location: The certificate issuer’s locality (city, town, etc.)
• Organization Information: The organization to which the certificate issuer
belongs
• Common Name: Name used to match authentication credentials
To add a local certificate, click Add.
Remove a local certificate by selecting the certificate and clicking the
Remove button.
©2016 Cradlepoint. All Rights Reserved. | +1.855.813.3385 | cradlepoint.com
87
User Manual / AER2100
11/21/16
CERTIFICATE SIGNING REQUEST
Request a certificate signature from a remote CA. Using an established, third-party CA increases the likelihood
that your certificate will be trusted by others (see security issues for self-signed certificates for more
information).
Generate a certificate signing request (CSR) by selecting a certificate from the dropdown list (Certificate Name
field) and downloading the CSR. The CSR can then be sent to a remote CA for a signature. Once the certificate
has been signed, import the certificate in PEM or PKCS #12 format.
When you export the CSR, select a Digest, or cryptographic hash function. These are listed in order of increasing
security. More security requires more router resources.
•
•
•
MD5
SHA-128
SHA-256
PEM
PEM is a container format for encoding data – in this case,
X.509 certificates. PEM was originally designed for encoding
email (PEM stands for Privacy-enhanced Electronic Mail), but
it has never been widely used for that purpose. The format is
much more common for encoding digital certificates.
The PEM format uses Base64 and DER (Distinguished Encoding
Rules) encoding.
To import, choose a certificate file in PEM format from your
computer or local device and upload it to the router. Give the
certificate a name that is meaningful to you.
To export, select a local certificate from the dropdown list and
download it to your computer or local device in PEM format.
PKCS12
PKCS #12 is one of the public-key cryptography standards.
PKCS #12 files bundle public and private certificate keys in an
archive file format. The PKCS #12 container format is more
secure than the PEM container format because it is protected
by an encryption key.
To import, choose a certificate file in PKCS #12 format from
your computer or local device and upload it to the router. Give
the certificate a name that is meaningful to you. PKCS #12
files are protected by a passphrase – you must know this key
to import the file.
©2016 Cradlepoint. All Rights Reserved. | +1.855.813.3385 | cradlepoint.com
88
User Manual / AER2100
11/21/16
To export, select a local certificate from the dropdown list and download it to your computer or local device in
PKCS #12 format. When you export this file, you must create a passphrase to protect it. This key is required for
future use of the file.
©2016 Cradlepoint. All Rights Reserved. | +1.855.813.3385 | cradlepoint.com
89
User Manual / AER2100
11/21/16
SYSTEM
ADMINISTRATION
ROUTER SECURITY
When the router is
configured to use the
advanced security mode,
several aspects of the
routers configuration and
networking functionality
will be extended to support
high security environments. This includes support for multiple user accounts,
increased password security and additional network spoofing filters. If you plan to
use your router in a PCI DSS compliant environment this option is mandatory.
REMOTE ADMIN
Remote Management allows a user to enable incoming WAN pings or change settings for the router from the
Internet using the router’s Internet address.
Allow WAN pings – When enabled the functionality allows an external WAN client to ping the router.
Allow Remote Web Administration – When remote administration is enabled it allows access to these
administration web pages from the Internet. With it disabled, you must be a client on the local network to
access the administration website. For security, remote access is usually done via a non-standard http port.
Additionally, encrypted connections can be required for an added level of security.
•
•
•
Require HTTPS Connection – Requiring a secure (https) connection is recommended
HTTP Port: Default – 8080. This option is disabled if you select “Require Secure Connection”
Secure HTTPS Port – Default: 8443.
©2016 Cradlepoint. All Rights Reserved. | +1.855.813.3385 | cradlepoint.com
90
User Manual / AER2100
11/21/16
NOTE: You can restrict remote access to only specified IP
addresses in SECURITY > Zone Firewall > Remote Access
Restriction.
Allow Remote SSH Access – This will enable SSH access
to the router from the Internet. It is only available
when SSH access is enabled in the Local Management
tab. Some carriers block the remote SSH access ports.
If a ping to the router’s WAN port does not work, it is
unlikely that remote SSH access will work.
FEATURE LICENSES
Some Cradlepoint features may require a license. These
features are disabled by default. To obtain a feature
license, contact your Cradlepoint sales representative.
Once you have obtained the feature license file, upload
the file to enable the feature. A reboot is required after
uploading a feature license file.
SYSTEM CLOCK
Enabling NTP will tell the router to get its system time
from a remote server on the Internet. If you do not
enable NTP then the router time will be based on when
the router firmware was built, which is guaranteed to
be wrong. Whenever the Internet connection is reestablished and once a week thereafter the router will
ask the server for the current time so it can correct
itself.
You then have the option of selecting an NTP server and
adjusting the NTP server port. Select the NTP server
from the dropdown list. Any of the given NTP servers
will be sufficient unless, for example, you need to
synchronize your router’s time with other devices in a
network.
•
•
Time Zone – Select from a dropdown list. Setting your Time Zone is required to properly show time in your
router log.
Daylight Savings Time – Select this checkbox if your location observes daylight saving time.
LOCAL MANAGEMENT
•
Enable Internet Bounce Pages – Bounce pages show up in your web browser when the router is not
connected to the Internet. They inform you that you are not connected and try to explain why. If you
©2016 Cradlepoint. All Rights Reserved. | +1.855.813.3385 | cradlepoint.com
91
User Manual / AER2100
•
•
•
•
•
•
•
•
•
•
11/21/16
disable bounce pages then you will just get the usual
browser timeout. In the normal case when the router is
connected to the Internet you don’t see them at all.
Reboot Count – Track number of router reboots.
Enable Login Banner – Add the CLI banner to the router’s
login page.
Local Domain – The local domain is used as the suffix for
DNS entries of local hosts. This is tied to the hostnames
of DHCP clients as DHCP_HOSTNAME.LOCAL_DOMAIN.
System Identifier – This is a customizable identity that
will be used in router reporting and alerting. The default
value is the product name and the last three characters
of the MAC address of the router.
Asset Identifier – This is a customizable string that will
be used in router reporting and alerting.
Require HTTPS Connection – Check this box if you want
to encrypt all router administration communication.
Secure HTTPS Port – Enter the port number you want to
use. The default is 443.
Enable SSH Server – When the router’s SSH server is
enabled you may access the router’s command line
interface (CLI) using the standards-based SSH protocol. Use the username “admin” and the standard system
password to log in.
SSH Server Port – Default: 22.
Automatically Set System Identifier – This will automatically set the system ID to the name of the first
client that gets a DHCP lease. This feature cannot be used with email alerts but alerts can be sent to ECM.
GPS
If you have an attached device with GPS support, you can enable a graphical view of your router’s location,
which appears in STATUS > GPS. SIM-based models with GPS support require that the SIM be inserted. Some
carriers disable GPS support in otherwise supported modems. If you encounter issues with obtaining a fix,
contact your carrier and ensure that GPS is supported.
Enable GPS – Enable support for querying GPS information from capable modems.
Enable GPS Keepalive – Poll the GPS every 10 seconds to keep hardware from sleeping.
Send to Client(s)
•
•
•
•
•
Enable this Server - Enables a local server to which
clients can connect and recieve GPS sentences.
Server Name - Your server’s name should include
only Aa-Zz, numerals, and ‘_’.
Enable GPS server on LAN - Enables a server on the
LAN side of the firewall which will periodically send
GPS sentences to TCP connected clients.
Enable GPS server on WAN - Enables a server on
the WAN side of the firewall which will periodically
send GPS sentences to TCP connected clients.
Port - Choose a port between 1 and 65535.
©2016 Cradlepoint. All Rights Reserved. | +1.855.813.3385 | cradlepoint.com
92
User Manual / AER2100
11/21/16
Send to Server(s)
•
•
•
•
•
•
•
Enable this client - Enables periodic reporting of
GPS sentences to a remote server. The router will
buffer GPS sentences if errors are encountered or
if the Internet connection goes down, and send the
buffered sentences when the connection is restored.
Client name - Your client’s name should include only
Aa-Zz, numerals, and ‘_’.
Server - Remote server hostname or IP.
Port - Remote server port.
Specify Time Interval - Restricts the GPS sentence
reporting to a remote server to a specific time
interval.
Start Time - Reporting start time.
End Time - Reporting end time.
NMEA GGA SENTENCES
The device reports GPS information with the NMEA (National Marine Electronics Association) GGA sentence
format. GGA provides essential fix data. For more examples and information about NMEA GGA, see the following
websites:
•
•
http://aprs.gids.nl/nmea/
http://www.gpsinformation.org/dale/nmea.htm#nmea
GGA
$GPGGA – Essential fix data including 3D location and accuracy information
Example: $GPGGA,1753405,4916.450,N,12311.127,W,2,06,1.5,117.3,M,−26.574,M,6.0,0138*47
Sample Data
Description
1753405
Time of fix – 17:34:05 UTC
4916.450,N
Latitude 49 deg. 16.450 min North
12311.127,W
Longitude 123 deg. 11.127 min West
2
Fix quality: 0 = fix not available; 1 = GPS fix; 2 = Differential GPS fix; 3 = PPS fix; 4 = Real Time Kinematic; 5 =
Float RTK; 6 = estimated (dead reckoning); 7 = Manual input mode; 8 = Simulation mode
06
Number of satellites being tracked
1.5
Horizontal dilution of precision (HDOP) – relative accuracy of horizontal position
117.312,M
Altitude in meters above mean sea level
-26.574,M
Geoidal separation: height of mean sea level above WGS-84 earth ellipsoid (negative value means mean sea level
is below ellipsoid)
6.0
Time in seconds since last update from differential reference stations
0138
Differential reference station ID number
*47
Checksum – used by program to check for transmission errors
©2016 Cradlepoint. All Rights Reserved. | +1.855.813.3385 | cradlepoint.com
93
User Manual / AER2100
11/21/16
SMS
SMS (Short Message Service, or text messaging) requires a cellular modem with an active data plan. SMS is not
designed to be a full remote management feature: SMS allows you to connect to the router for a few simple
queries or commands with a text messaging service (e.g., from your phone). A modem that does not have an
active data connection may still be reachable by
SMS because Internet traffic and SMS traffic operate
on separate channels, so SMS can be used to bring
an offline router back online.
SMS is enabled on the router by default. However,
it only works if SMS is supported and enabled on
the modem. Most modems have SMS enabled by
default, but the carrier may charge a fee for each
text message sent or received. Contact your carrier
to review these fees and/or to enable an SMS plan.
Important notes about SMS:
•
•
•
•
Messages are limited to 160 characters.
SMS is not a guaranteed delivery protocol.
The carriers do not guarantee that the SMS message will be delivered to the modem or that the modem’s
response will be delivered to the sender. This means an administrator might have to send messages multiple
times before the desired action is performed.
SMS is a slow protocol. It can take seconds or up to a few minutes for messages to be delivered.
SMS messages are not encrypted; they are sent in full readable text over the network.
Enable SMS support – SMS support is enabled by default on the router. Deselect this to disable.
Password – By default, the password is the last eight characters of the router’s MAC address (i.e., the Default
Password on the product label). You can change this password to anything between 1 and 16 characters. It
should be long enough to be useful for security but short enough to easily type into your phone (or other
texting client).
White List – This list is blank by default, which means that the router will accept SMS messages from any phone
number. Leaving this blank is unsecure, so Cradlepoint recommends that you add phone numbers to this list.
Once any numbers are listed, only those numbers have the ability to connect to the router via SMS.
SYSTEM LOGGING
Logging Level: Setting the log level controls which messages are
stored or filtered out. A log level of Debug will record the most
information while a log level of Critical will only record the most
urgent messages. Each level includes all messages from all of
the levels below it on the list (e.g. “Warning” includes all “Error”
and “Critical” messages as well).
•
•
•
•
•
Debug
Info
Warning
Error
Critical
Enable Logging to a Syslog Server: Enabling this option will
send log messages to a specified Syslog server. After enabling,
type the Hostname or IP address of the Syslog server (or select from the dropdown menu).
©2016 Cradlepoint. All Rights Reserved. | +1.855.813.3385 | cradlepoint.com
94
User Manual / AER2100
•
•
•
11/21/16
Syslog Server Address: Select the Hostname or IP address from the dropdown menu, or type this in
manually.
Include System ID: This option will include the router’s “System ID” at the beginning of every log message.
This is often useful when a single remote Syslog server is handling logs for several routers.
Include UTF8 Byte Order Mark: The log message is sent using UTF-8 encoding. By default the router will
attach the Unicode Byte Order Mark (BOM) to the Syslog message in compliance with the Syslog protocol,
RFC5424. Some Syslog servers may not fully support RFC5424 and will treat the BOM as ASCII text, which
will appear as garbled characters in the log. If this occurs, disable this option.
Log to attached USB stick: Only enable this option if instructed by a Cradlepoint support agent. This will write a
very verbose log file to the root level of an attached USB stick. Please disable the feature before removing the
USB stick, or you may lose some logging data.
Verbose modem logging: Only enable this option if instructed by a Cradlepoint support agent.
Create support log: This functionality allows for a quick collection of system logging. Create this log file when
instructed by a Cradlepoint support agent.
ROUTER SERVICES
By default, router services (Enterprise Cloud Manager,
NTP, etc.) connect to the router via the WAN. In some
setups it makes sense to use the LAN instead. For
example, if your router is used strictly for 3G/4G failover
behind another router, you may not want to use 3G/4G
data unnecessarily. Select Use LAN Gateway to set your
router services to connect via the LAN.
LAN Gateway Address: Input the IP address of the
LAN side connection. If this is a 3G/4G failover router
operating behind another router, the LAN Gateway
Address is the IP address of that other router.
DNS Server and Secondary DNS Server: The primary and secondary DNS server numbers match the static DNS
values (set at NETWORKING > DNS Servers). You can leave the default values or set them manually here.
(Changing these values also changes the static DNS values.)
LLDP
The Link Layer Discovery Protocol (LLDP) is a standard
method for network devices to share information about
themselves among their neighbors. The router stores the
information it receives from its neighbors, which can be
viewed on the STATUS > LLDP page.
Enable LLDP for Ethernet on the WAN and/or LAN.
©2016 Cradlepoint. All Rights Reserved. | +1.855.813.3385 | cradlepoint.com
95
User Manual / AER2100
11/21/16
ENTERPRISE CLOUD MANAGER
Cradlepoint Enterprise Cloud Manager (ECM) is a cloud-based management service for configuring, monitoring,
and organizing your Cradlepoint routers. Key features include the following:
•
•
•
•
Group based configuration management
Health monitoring of router connectivity and data usage
Remote management and control of routers
Historical record keeping of device logs and status
Registering Your Router – Once you have signed up for ECM, click on the Register Router button to begin
managing the router through ECM. Input your ECM Username and ECM Password and click Register. You have now
registered the device with Enterprise Cloud Manager.
Suspending the ECM Client – Click on the Suspend Client button to stop communication between the device and
ECM. Suspending the client will make it stop any current activity and go dormant. It will not attempt to contact
the server while suspended. This is a temporary setting that will not survive a router reboot; to disable the
client altogether use the Advanced Enterprise Cloud Manager Settings panel (below).
Enterprise Cloud Manager Settings (Advanced)
• Enabled: Enable the ECM client to contact the server. While this box is unchecked, the ECM client will never
attempt to contact the server. (Default: Enabled)
• Server Host:Port: The DNS hostname
and port number for your ECM server.
(Default: stream.cradlepoint.com)
• Session Retry Timer: How long to
wait, in seconds, before starting a new
ECM session following a connection
drop or connectivity failure. Note that
this value is a starting point for an
internal backoff timer that prevents
superfluous retries during connectivity
loss.
• Unmanaged Checkin Timer: How often,
in seconds, the router checks with ECM to see if the router is remotely activated. Note that this value is a
starting point for an internal backoff timer that reduces network usage over time.
• Maximum Alerts Buffer: The maximum number of alerts to buffer when offline.
DEVICE ALERTS
The Device Alerts submenu choice allows you to receive email notifications of specific system events. YOU MUST
ENABLE AN SMTP EMAIL SERVER TO RECEIVE ALERTS.
Alerts can be included for the following:
•
•
Firmware Upgrade Available: A firmware update is available for this device.
System Reboot Occurred: This router has rebooted. This depends on NTP being enabled and available to
report the correct time.
©2016 Cradlepoint. All Rights Reserved. | +1.855.813.3385 | cradlepoint.com
96
User Manual / AER2100
•
•
•
•
•
•
•
•
•
•
•
•
11/21/16
Unrecognized MAC Address: Used with
the MAC monitoring lists. An alert is sent
when a new unrecognized MAC address is
connected to the router.
WAN Device Status Change: An attached
WAN device has changed status. The
possible statuses are plugged, unplugged,
connected, and disconnected.
Configuration Change: A change to the
router configuration.
Login Success: A successful login attempt
has been detected.
Login Failure: A failed login attempt has
been detected.
Account Locked: Account has been locked
due to excessive failed login attempts.
IP Address Banned: An IP address has
been banned.
VPN Tunnel Goes Down: Sends an alert
when a VPN tunnel goes down.
Feature License Expiration: Sends an alert
when a feature license is about to expire.
Router SDK Application: A router SDK Application may send an alert.
Full System Log: The system log has filled. This alert contains the contents of the system log.
Recurring System Log: The system log is sent periodically. This alert contains all of the system events since
the last recurring alert. It can be scheduled for daily, weekly and monthly reports (Frequency). You also
choose the Time you want the alert sent.
SMTP Mail Server
Since your router does not have its own email server, to receive alerts you must enable an SMTP server. This is
possible through most email services (Gmail, Yahoo, etc.)
Each SMTP server will have different specifications for setup, so you have to look those up separately. The
following is an example using Gmail:
•
•
•
•
•
•
•
Server Address: smtp.gmail.com
Server Port: 587 (for TLS, or Transport Layer Security port; the router does not support SSL).
Authentication Required: For Gmail, mark this checkbox.
User Name: Your full email address
Password: Your Gmail password
From Address: Your email address
To Address: Your email address
Once you have filled in the information for the SMTP server, click on the “Verify SMTP Settings” button. You
should receive a test email at your account.
Delivery Options (Advanced)
Email Subject Prefix: This optional string is prefixed to the alert subject. It can be customized to help you
identify alerts from specific routers.
Retry Attempts: The number of attempts made to send an alert to the mail server. After the attempts are
exhausted, the alert is discarded.
Retry Delay: The delay between retry attempts.
©2016 Cradlepoint. All Rights Reserved. | +1.855.813.3385 | cradlepoint.com
97
User Manual / AER2100
11/21/16
SERIAL REDIRECTOR
A single USB Serial device can be used to establish a serial link to a host port on the router. The USB Serial
device can also be accessed by running “serial” from an SSH session.
Telnet to Serial Configuration
• Enabled: Enabling Telnet to Serial will start a Telnet server that
passes its connection to the serial adapter. Enabling this service
is not necessary when accessing serial through SSH.
• LAN: Enable serial redirector for LAN connections.
• Authenticated LAN: Enable serial redirector for Authenticated
LAN connections. You must be logged into the router to use the
redirector.
• WAN: Enable serial redirector for WAN connections.
• Server Port: Enter a port number for the redirector to use. (Default: 7218)
SNMP CONFIGURATION
SNMP, or Simple Network Management Protocol, is an Internet standard protocol for remote management. You
might use this instead of Enterprise Cloud Manager if you want to remotely manage a set of routers that include
both Cradlepoint and non-Cradlepoint products.
SNMP Configuration
•
Enable SNMP: Selecting “Enable
SNMP” will reveal the router’s SNMP
configuration options.
Network Settings
• Enable SNMP on LAN: Enabling SNMP
on LAN will make SNMP services
available on the LAN networks
provided by this router. SNMP
will not be available on guest or
virtual networks that do not have
administrative access.
• LAN port #: Use the LAN port # field
to configure the LAN port number
you wish to access SNMP services on.
(Default: 161)
• Enable SNMP on WAN: Enabling
SNMP on WAN will make SNMP
services available to the WAN
interfaces of the router.
• WAN port #: Use the WAN port # field
to configure which publicly accessible
port you wish to make SNMP services
available on. (Default: 161)
©2016 Cradlepoint. All Rights Reserved. | +1.855.813.3385 | cradlepoint.com
98
User Manual / AER2100
•
11/21/16
SNMP Version
• SNMPv1: SNMP version 1 is the most basic version of SNMP. SNMPv1 will configure the router to
transmit with settings compatible with SNMP version 1 protocols.
• SNMPv2c: SNMP version 2c has the same features as v1 with some additional commands. SNMPv2c will
configure the router to use settings and data formatting compatible with SNMP version 2c.
• SNMPv3: SNMP version 3 includes all prior features with security available. SNMPv3 is the most secure
setting for SNMP. If you wish to configure traps then you must use SNMP version 3.
SNMP v1 & v2c Settings
• Get community string: The “Get community string” is used to read SNMP information from the router. This
string is like a password that is transmitted in regular text with no protection.
• Set community string: The “Set community string” is used when writing SNMP settings to the router. This
string is like a password. It is a good idea to make it different than the “Get community string.”
SNMPv3
If you select SNMPv3, you have several additional configuration options for added security.
•
•
•
•
•
•
•
•
•
•
•
•
•
Authentication type: Select the authentication and encryption type that will be used when connecting to
the router from the following dropdown list. These settings must match the configuration used on any
SNMP clients.
MD5 with no encryption
SHA with no encryption
MD5 with DES encryption
SHA with DES encryption
MD5 with AES encryption
SHA with AES encryption
Username: Enter the Username configured on your SNMP host in the username field.
Password: Enter the Password for your SNMP host in the password and verify password fields. This
password must be at least eight characters long.
Enable SNMP traps: Enabling traps will allow you to configure a destination server, community, and port for
trap notifications. Trap notifications are returned to the server with SNMPv1.
Trap community string: The trap notifications will be returned to the trap server using this SNMPv1 trap
community name.
Address for trap server: Enter the address of the host system that you want trap alerts sent to.
Trap server port #: Enter the port number that the remote host will be listening for trap alerts on. (Default:
162)
General Settings
System information via SNMP is Read-Writable by default. However, if a value is set here, that field will become
Read Only.
•
•
•
System Contact: Input the email address of the system administrator.
System Name: Input the router’s hostname.
System Location: Input the physical location of the router. This is simply a string for your own information.
©2016 Cradlepoint. All Rights Reserved. | +1.855.813.3385 | cradlepoint.com
99
User Manual / AER2100
11/21/16
SYSTEM CONTROL
SYSTEM FIRMWARE
This allows the administrator to load new firmware onto the router to add new
features or fix defects. If you are happy with the operation of the router, you may
not want to upgrade just because a new version is available. Check the firmware
release notes (cradlepoint.com/firmware) for information to decide if you should
upgrade.
Current Firmware Version: Shows the
number of the current firmware and
the date it was updated.
Available Firmware Version: If there
is a new firmware version available,
this will list the version number. Click
“Check Again” to have the router check
for the newest firmware.
Automatic Firmware Check: Automatically check for new firmware
updates once daily.
Manual Firmware Upload: Upload the router firmware from an
attached computer. (Go to cradlepoint.com/firmware to download the
firmware.)
System Config Save/Restore
Download Settings: Click on “Dowload Settings” to save your current
settings to a file on a computer.
Restore Settings: Click on “Restore Settings” to restore your previous
settings from a file on a computer.
Firmware Management
Load new firmware and restore your previous settings from a file on
a computer without rebooting between steps.
MODEM FIRMWARE
This allows the administrator to load new firmware onto Cradlepoint modems attached to the router. Note
that modem firmware is separate from router firmware. New modem firmware may be necessary to update the
module due to carrier updates or defect resolution. If you are happy with the operation of the modem, you may
not want to upgrade just because a new version is available. Please check the modem firmware release notes for
information to decide if you should upgrade or not.
Most Cradlepoint modems contain a single firmware image that can be Checked, Updated or manually updated.
With some modems (such as LPE), you have the ability to change the firmware to support a different carrier
image. With other select modems (such as LP6), more than one modem firmware image may be locally stored
within the device’s memory.
You must first select the Cradlepoint modem you would like to update. Once selected, the appropriate modem
firmware update options will display.
©2016 Cradlepoint. All Rights Reserved. | +1.855.813.3385 | cradlepoint.com
100
User Manual / AER2100
11/21/16
For modems supporting manual
carrier switching (such as LPE), select
File to browse to an appropriate,
different modem firmware package
file to load into the modem’s
memory.
Firmware updates can be performed
on any firmware line item using
the Check/Upgrade or File (manual)
process.
The following actions are available to
be configured:
•
Automatically check for new firmware: Click the checkbox to indicate whether the system is to
automatically check for available modem firmware updates. When enabled, the system checks once a day.
This global setting applies to all modems connected to the router.
•
Select Modem: Select the appropriate modem which you would like to update. Note that dual SIM devices
are listed as a single modem.
In the Installed Firmware grid, you will see the following columns:
•
Active (Multi-firmware modems only): Indicates which carrier package is currently active on the modem.
Note: You cannot select the active image. On multi-firmware modems, the carrier firmware is selected
automatically.
•
Carrier: Displays the carrier supported by the modem firmware. For carriers not otherwise available,
“Generic” will be displayed.
•
Current Package Version: Displays the current firmware package version loaded on the modem.
•
Available Firmware Version: Displays the firmware version available for upgrade or indicates status of the
current firmware. If new firmware is available, the available upgrade version is displayed.
•
Upgrade: Click this button to download the Available Firmware Version file and perform this over-the-air
upgrade. If a connection error occurs, it is possible that HTTPS is blocked for the upgrade check. Enable Allow
HTTP Firmware Check in SYSTEM > System Control >System Firmware to address this issue.
•
Check: Click this button to refresh or update the Available Firmware Version status column.
•
File: Click this button to manually upload a modem firmware file. Type the path/file or click Select Firmware
File to browse to the local file location. Once entered, click Begin Firmware Upgrade. Note: For modems which
support manual carrier switching, find the appropriate modem firmware package file via ECM or the Cradlepoint
portal.
©2016 Cradlepoint. All Rights Reserved. | +1.855.813.3385 | cradlepoint.com
101
User Manual / AER2100
11/21/16
DEVICE OPTIONS
Reboot Options
•
•
•
Reboot the Device: Manually restart the router.
Factory Reset Router: Reset the router to its
original settings. Once reset your SSID and
admin password will match the sticker on the
bottom of the router.
Device Console: Access router’s command line
interface (CLI) console.
Scheduled Reboot
•
•
Scheduled Reboot: Router will restart at userspecified time.
Enable Watchdog Reboot: Router will restart
when it determines an unrecoverable error
condition has occurred.
DIAGNOSTICS
Ping Test
A simple test to check Internet connectivity. Type
the Hostname or IP address of the computer you
want to ping and click the ‘Ping’ button.
Speed Test
• Tests Against Cradlepoint Server - Up to ten
speed tests are permitted against a Cradlepoint
server.
• WAN Device - The WAN Device that is selected
will have the test run on it. If no device is
selected then the highest priority connected
device will be used.
• Custom Server - Type the Hostname or IP
address of the server to which you wish to
perform a test. If left empty the test will be
done to a Cradlepoint server.
• Custom Port (Optional) - The port to which the
test is directed.
• Max Duration - The Max Duration is the
Maximum amount of time for which the test
should be run. The test may finish sooner if
sufficient data is collected.
• Data Limit - The Data Limit is the limit of how much data will be transferred while measuring the connection
speed; this should be limited to reduce the expense of a speed test. Setting the limit to 0 will cause the test
to run until enough data is collected or the duration limit is met.
• Test Type - Select the type of test you would like to run. TCP Upload will test speed going to the server, TCP
Download will test speed coming to the client, and UDP will measure the speed going to the server.
©2016 Cradlepoint. All Rights Reserved. | +1.855.813.3385 | cradlepoint.com
102
User Manual / AER2100
11/21/16
SETUP WIZARDS
ECM REGISTRATION
To register the router with
Cradlepoint ECM you must first
have an account. If you need to
create an account you can signup at
cradlepoint.com.
Once you’ve created an account,
or if you already have one, you
can enter your ECM username and
password to register the router.
FIRST TIME SETUP
Administrator Password and Time Zone
Enter a password for the administrator who will have full
access to the router’s management interface.
You can use the default password on the back of your
product, or you can create a custom Administrator Password.
Configuring Your Wireless Network
• Wireless Network Name - When you are browsing for
available wireless networks, this is the name that
will be broadcast from this router. This name is also
referred to as the SSID. For security purposes, it is highly
recommended you change the pre-configured wireless
network name.
• Enable Guest Network - If the guest network is enabled,
anyone can connect to the special guest network
which allows limited connectivity to the Internet while
preventing access to your local network.
• Security Mode
• Best (WPA2): Select this option if your wireless
adapters support WPA2-only mode. This will
connect to most new devices and is the most
secure, but may not connect to older devices or
some handheld devices such as a PSP.
• Good (WPA1 & WPA2): Select this option if your
wireless adapters support WPA or WPA2. This is the
most compatible with modern devices and PCs.
• Poor (WEP): Select this option if your wireless
adapters only support WEP. This should only be
used if a legacy device that only supports WEP will
be connected to the router. WEP is insecure and
obsolete and is only supported in the router for
©2016 Cradlepoint. All Rights Reserved. | +1.855.813.3385 | cradlepoint.com
103
User Manual / AER2100
•
11/21/16
legacy reasons. The router cannot use 802.11n modes if WEP is enabled; router WiFi performance and
range will be limited.
• None (OPEN): Select this option if you do not want to activate any security features.
WPA Password - The WPA Password must be between 8 and 64 characters long. A combination of upper
and lower case letters along with numbers and special characters is recommended to prevent hackers from
gaining access to your network.
Configuring Your APN and Modem Authentication
If you are using a SIM-based modem (LTE/GSM/HSPA) with
your Cradlepoint router you may need to configure the APN
before it will properly connect to your carrier. Wireless
carriers offer several APNs so check with your carrier to
confirm the appropriate one to use. You can use the default
password on the back of your product, or you can create a
custom Administrator Password.
NOTE: DO NOT USE THIS APN WIZARD if you have already
configured an APN. Any specific modem settings will not
be overwritten by this generic APN setup. Leave this
setting as default and after finishing this Wizard go to
the CONNECTION MANAGER page, select your modem, and
edit the settings. The SIM PIN/APN tab has more available
settings than are provided here.
Some modems require a username and password to be
entered to authenticate with a carrier. Do not fill in the
following fields unless you are sure your modem needs
authentication.
•
•
•
Authentication Protocol
Username
Password
Enable and Configure Failure Check
Failure check will test the connection to verify the WAN
device is connected.
•
•
•
Idle Check Interval: Set the number of seconds the
router will wait between checks to see if the WAN is
still available.
Failure Check:
• Off: Once the link is established the router takes
no action to verify that it is still up.
• On: Modems will be set to use the Passive DNS
failure check type. Ethernet and WiFi as WAN
connections will be set to use Active Ping.
Ping IP Address: This IP address must be an address
that can be reached through your WAN connection
(modem/Ethernet). Some ISPs/Carriers block certain
addresses, so choose an address that all of your WAN
connections can use.
Summary
Review your settings and click Finish to exit or Back to edit.
©2016 Cradlepoint. All Rights Reserved. | +1.855.813.3385 | cradlepoint.com
104
User Manual / AER2100
11/21/16
IP PASSTHROUGH SETUP
IP passthrough takes a 3G/4G WAN
data source (USB, ExpressCard, or
Cradlepoint business-grade modem)
and passes the IP address through to
Ethernet LAN.
Enabling IP passthrough will make
many changes to your router
configuration. Please review this list
and ensure they are compatible with
how the router will be used.
•
•
•
•
•
•
•
All Ethernet ports will be set to
LAN
All network groups except the
primary network group will be
removed
All WAN devices will have Load
Balance disabled and the highest
priority device will be used
All Wireless interfaces will
be removed from the primary
network group
All Router based VPN and GRE
services will be disabled
The Routing Mode will be set to IP
Passthrough
The Subnet Selection Mode will be set to “Automatically Create Subnet” unless overridden via the Subnet
Selection Mode dropdown
Any Ethernet WAN connections should be disconnected before IP passthrough is enabled.
©2016 Cradlepoint. All Rights Reserved. | +1.855.813.3385 | cradlepoint.com
105
User Manual / AER2100
11/21/16
APPENDIX
SAFETY, REGULATORY, AND WARRANTY GUIDE
CRADLEPOINT AER2100
MODEL: S3A340A
This important Product Information and Safety Guide contains safety, handling, disposal, regulatory, trademark, copyright, and software
licensing information. To avoid injury, read all safety information below and operating instructions before using the device.
FEDERAL COMMUNICATION COMMISSION INTERFERENCE STATEMENT
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules.
These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment
generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may
cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular
installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the
equipment off and on, the user is encouraged to try to correct the interference by one of the following measures:
•
•
•
•
Reorient or relocate the receiving antenna
Connect the equipment into an outlet on a circuit different from that to which the receiver is connected
Increase the separation between the equipment and receiver
Consult the dealer or an experienced radio/TV technician for help
FCC CAUTION
Any changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate
this equipment.
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause
harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired
operation.
FCC STATEMENT
For product available in the USA/Canada market, only channel 1-11 can be operated. Selection of other channels is not possible.
This device is restricted for indoor use.
FCC RADIATION EXPOSURE STATEMENT
This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. This equipment should be
installed and operated with minimum distance 20 cm between the radiator and your body.
This device and its antenna(s) must not be co-located or operating in conjunction with any other antenna or transmitter except in
accordance with FCC multi-transmitter product procedures.
To comply with FCC regulations limiting both maximum RF output power and human exposure to RF radiation, the maximum cellular
antenna gain must not exceed 3 dBi.
To comply with FCC regulations limiting both maximum RF output power and human exposure to RF radiation, the maximum WiFi antenna
gain must not exceed 5 dBi.
INDUSTRY CANADA STATEMENT
This device complies with Industry Canada license-exempt RSS standards. Operation is subject to the following two conditions: (1) this
device may not cause interference, and (2) this device must accept any interference, including interference that may cause undesired
operation of the device.
©2016 Cradlepoint. All Rights Reserved. | +1.855.813.3385 | cradlepoint.com
106
User Manual / AER2100
11/21/16
INDUSTRY CANADA RADIATION EXPOSURE STATEMENT
This equipment complies with IC radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed
and operated with a minimum distance of 20 cm between the radiator and your body.
This radio transmitter (IC: 6921A-S4A525A) has been approved by Industry Canada to operate with the antenna types listed below with
the maximum permissible gain and required antenna impedance for each antenna type indicated. Antenna types not included in this list,
having a gain greater than the maximum gain indicated for that type, are strictly prohibited for use with this device.
For product available in the USA/Canada market, only channel 1-11 can be operated. Selection of other channels is not possible.
The device for the band 5150-5250 MHz is only for indoor usage to reduce potential for harmful interference to co-channel mobile
satellite systems.
This device and its antenna(s) must not be co-located or operating in conjunction with any other antenna or transmitter except in
accordance with IC multi-transmitter product procedures.
These devices have been designed to operate with cellular antennas having a maximum gain of 3 dBi. Antennas having a higher gain are
strictly prohibited per regulations of Industry Canada. The required antenna impedance is 50 ohms.
These devices have been designed to operate with WiFi antennas having a maximum gain of 5 dBi. Antennas having a higher gain are
strictly prohibited per regulations of Industry Canada. The required antenna impedance is 50 ohms.
DÉCLARATION D’INDUSTRIE CANADA
Le présent appareil est conforme aux CNR d’Industrie Canada applicables aux appareils radio exempts de licence. L’exploitation est
autorisée aux deux conditions suivantes: (1) l’appareil ne doit pas produire de brouillage, et (2) l’utilisateur de l’appareil doit accepter
tout brouillage radioélectrique subi, même si le brouillage est susceptible d’en compromettre le fonctionnement.
Pour les produits disponibles aux États-Unis/Canada du marché, seul le canal 1 à 11 peuvent être exploités. Sélection d’autres canaux
n’est pas possible.
Les dispositifs fonctionnant dans la bande 5150-5250 MHz sont réservés uniquement pour une utilisation à l’intérieur afin de réduire les
risques de brouillage préjudiciable aux systèmes de satellites mobiles utilisant les mêmes canaux.
NOTE IMPORTANTE (POUR L’UTILISATION DE DISPOSITIFS MOBILES): DÉCLARATION
D’EXPOSITION AUX RADIATIONS
Cet équipement est conforme aux limites d’exposition aux rayonnements IC établies pour un environnement non contrôlé. Cet
équipement doit être installé et utilisé avec un minimum de 45 cm de distance entre la source de rayonnement et votre corps.
Cet appareil et son antenne(s) ne doit pas être co-localisés ou fonctionnement en association avec une autre antenne ou transmetteur.
Le présent émetteur radio (IC: 6921A-S4A525A) a été approuvé par Industrie Canada pour fonctionner avec les types d’antenne énumérés
ci-dessous et ayant un gain admissible maximal et l’impédance requise pour chaque type d’antenne. Les types d’antenne non inclus dans
cette liste, ou dont le gain est supérieur au gain maximal indiqué, sont strictement interdits pour l’exploitation de l’émetteur.
INFORMATION FOR EUROPE, DECLARATION OF COMPLIANCE
Model: S3A340A
AER2100
Cradlepoint, Inc. declares that this device is in compliance with the essential requirements of the R&TTE Directive 1999/5/EC, Energy
Related Products Directive 2009/125/EC, Electromagnetic Compatibility Directive 2004/108/EC, Low Voltage Directive 2006/95/EC, and
RoHS2 Directive 2011/65/EU.
A copy of the original European DoC may be obtained from cradlepoint.com/product-certifications.
RF Exposure Statement: To comply with RF Exposure requirements, this equipment should be installed and operated with a minimum
distance of 20 cm between the radiating device and your body.
RECYCLING AND ENVIRONMENTAL INFORMATION
To find information on Cradlepoint’s commitment to our environment and how to responsibly recycle or recover Cradlepoint products at
the end of their useful life, please visit cradlepoint.com.
©2016 Cradlepoint. All Rights Reserved. | +1.855.813.3385 | cradlepoint.com
107
User Manual / AER2100
11/21/16
SAFETY AND HAZARDS
Under no circumstances should the device be used in any areas:
(a) where blasting is in progress,
(b) where explosive atmospheres may be present, or
(c) that are near (i) medical or life support equipment, or (ii) any equipment which may be susceptible to any form of radio interference.
In such areas, the device MUST BE POWERED OFF AT ALL TIMES (since the device otherwise could transmit signals that might interfere
with such equipment).
In addition, under no circumstances should the device be used in any aircraft, regardless of whether the aircraft is on the ground or in
flight. In any aircraft, the device MUST BE POWERED OFF AT ALL TIMES since the device otherwise could transmit signals that might
interfere with various onboard systems on such aircraft.
Furthermore, under no circumstances should the device be used by the driver or operator of any vehicle. Such use of the device will
detract from the driver’s or operator’s control of that vehicle. In some jurisdictions, use of the device while driving or operating a vehicle
constitutes a civil and/or criminal offense.
Due to the nature of wireless communications, transmission and reception of data by the device can never be guaranteed, and it is
possible that data communicated or transmitted wirelessly may be delayed, corrupted (i.e., contain errors), or totally lost.
The device is not intended for (and Cradlepoint recommends the device not be used in any) critical applications where failure to transmit
or receive data could result in property damage or loss or personal injury of any kind (including death) to the user or to any other party.
Cradlepoint expressly disclaims liability for damages of any kind resulting from:
(a) delays, errors, or losses of any data transmitted or received using the device; or
(b) any failure of the device to transmit or receive such data.
WARNING: This product is only to be installed by qualified personnel.
Purchaser agrees to indemnify Cradlepoint against any liability or damages caused to third parties as a result of Purchaser’s misuse or
misapplication of the Cradlepoint product.
OPEN SOURCE SOFTWARE
This product contains software distributed under one or more of the following open source licenses: GNU General Public License Version
2, BSD License, Net-SNMP License, and PSF License Agreement for Python 3.3. For more information on this software, including licensing
terms and your rights to access source code, contact Cradlepoint at cradlepoint.com/opensource.
WARRANTY INFORMATION
Cradlepoint, Inc. warrants this product against defects in materials and workmanship to the original purchaser (or the first purchaser in
the case of resale by an authorized distributor) for a period of one (1) year from the date of shipment. This warranty is limited to a repair
or replacement of the product, at Cradlepoint’s discretion as purchaser’s sole and exclusive remedy. Cradlepoint does not warrant that
the operation of the device will meet your requirements or be error free.
LIMITATION OF CRADLEPOINT LIABILITY
The information contained in this Safety, Regulatory, and Warranty Guide is subject to change without notice and does not represent
any commitment on the part of Cradlepoint or its affiliates. CRADLEPOINT AND ITS AFFILIATES HEREBY SPECIFICALLY DISCLAIM LIABILITY
FOR ANY AND ALL: (A) DIRECT, INDIRECT, SPECIAL, GENERAL, INCIDENTAL, CONSEQUENTIAL, PUNITIVE OR EXEMPLARY DAMAGES, INCLUDING
WITHOUT LIMITATION FOR LOSS OF PROFITS OR REVENUE OR OF ANTICIPATED PROFITS OR REVENUE ARISING OUT OF THE USE OR INABILITY
TO USE THE DEVICE, EVEN IF CRADLEPOINT AND/OR ITS AFFILIATES HAVE BEEN ADVISED OF THE POSSIBILITY OF SUCH DAMAGES, AND EVEN
IF SUCH DAMAGES ARE FORESEEABLE; OR (B) CLAIMS BY ANY THIRD PARTY. NOTWITHSTANDING THE FOREGOING, IN NO EVENT SHALL THE
AGGREGATE LIABILITY OF CRADLEPOINT AND/OR ITS AFFILIATES ARISING UNDER OR IN CONNECTION WITH THE DEVICE, REGARDLESS OF THE
NUMBER OF EVENTS, OCCURRENCES, OR CLAIMS GIVING RISE TO LIABILITY, EXCEED THE PRICE PAID BY THE ORIGINAL PURCHASER OF THE
DEVICE.
PRIVACY
Cradlepoint collects general data pertaining to the use of Cradlepoint products via the Internet including, by way of example, IP address,
device ID, operating system, browser type and version number, etc. To review Cradlepoint’s privacy policy, please visit cradlepoint.com/
privacy.
©2016 Cradlepoint. All Rights Reserved. | +1.855.813.3385 | cradlepoint.com
108
User Manual / AER2100
11/21/16
OTHER BINDING DOCUMENTS; TRADEMARKS; COPYRIGHT
By activating or using your AER2100 or AER2150 device, you agree to be bound by Cradlepoint’s Terms of Use, User License and other
applicable Legal Policies.
© 2015 Cradlepoint, Inc. All rights reserved. Cradlepoint is not responsible for omissions or errors in typography or photography.
Cradlepoint, AER2100, AER2150, and the Cradlepoint logo are trademarks of Cradlepoint, Inc. in the US and other countries. Other
trademarks are property of their respective owners.
ROUTER COMMUNICATION/DATA USAGE
The factory default configuration of the router is set to communicate with Cradlepoint and other resources at regular intervals to
access the latest firmware and modem updates, clock synchronization (NTP), and Enterprise Cloud Manager (ECM) membership. Such
communication may result in data usage and applicable charges regardless of whether the router uses a wired or wireless Internet
connection. To avoid such data usage and potential charges, consult the following Knowledge Base article:
http://knowledgebase.cradlepoint.com/articles/support/router-communication-data-usage
©2016 Cradlepoint. All Rights Reserved. | +1.855.813.3385 | cradlepoint.com
109
Download PDF
Similar pages