INDEX
ELECTRIC SYSTEM TOOLS
STEERING AND SUSPENSION TOOLS
42-53
FUEL INJECTION AND CARBURETION TOOLS 12-15
BRAKE SYSTEM TOOLS
54-57
ENGINE SYSTEM TOOLS
16-31
WHEEL AND CHAIN TOOLS
58-73
CLUTCH AND TRANSMISSION TOOLS
32-41
GENERAL SERVICE TOOLS
74-109
06-11
Item No.
Product
BS0044
HEADLIGHT & BRAKE SPRING HOOK
Page. Item No.
92
BS2462
Product
MAGNETO FLYWHEEL PULLER (M26 X P1.0)
Page.
30
BS0058
CARBURETOR ADJUSTING TOOL SET
13
BS2463
MAGNETO FLYWHEEL PULLER (M30 X P1.5)
30
BS0059
D TYPE SOCKET CARBURETOR ADJUSTING DRIVER (165mm)
13
BS2464
MAGNETO FLYWHEEL PULLER (M30 X P1.0)
30
BS0230
4PC LONG PICK & HOOK SET (152mm)
93
BS2465
MAGNETO FLYWHEEL PULLER (M30 X P1.5)
30
BS0231
PARALLEL TIP SLOT CARBURETOR ADJUSTING SCREWDRIVER (250mm)
13
BS2467
MAGNETO FLYWHEEL PULLER (M33 X P1.5)
30
BS2468
MAGNETO FLYWHEEL PULLER (M35 X P1.5)
30
BS0244
COOLING SYSTEM & RADIATOR PRESSURE TEST SET
23
BS2469
MAGNETO FLYWHEEL PULLER (M35 X P1.5)
30
BS0245
BRAKE FLUID CONDITION TESTER
57
BS2470
MAGNETO FLYWHEEL PULLER (M26 X P1.0)
29
BS02961
THREADED COIL INSERT REPAIRING KIT (METRIC)
102
BS2471
MAGNETO FLYWHEEL PULLER (M28 X P1.5)
29
BS0350
C HOOK WRENCH 19mm~51mm (3/4”~2”)
48
BS2472
MAGNETO FLYWHEEL PULLER (M28 X P1.0)
29
BS0351
C HOOK WRENCH 32mm~76mm (1-1/4”~3”)
48
BS2473
MAGNETO FLYWHEEL PULLER (M30 X P1.5)
29
BS0352
C HOOK WRENCH 51mm~120mm (2”~4-3/4”)
48
BS2474
MAGNETO FLYWHEEL PULLER (M33 X P1.5)
29
BS0353
CHAIN ADJUSTING C HOOK WRENCH
62
BS2475
MAGNETO FLYWHEEL PULLER (M20 X P1.0)
29
BS03531
BENELLI REAR WHEEL AXLE AND CHAIN ADJUSTING TOOL
65
BS2476
MAGNETO FLYWHEEL PULLER (M22 X P1.0)
29
BS1020
2PC BATTERY TERMINAL CLEANING TOOL KIT
9
BS2477
MAGNETO FLYWHEEL PULLER (M22 X P1.5)
29
BS1030
171PC HEAT SHRINK TUBE SET
7
BS2478
MAGNETO FLYWHEEL PULLER (M24 X P1.5)
29
BS1031
106PC WATERPROOF HEAT SHRINK TUBE SET
7
BS2479
MAGNETO FLYWHEEL PULLER (M26 X P1.5)
29
BS1034
WIRE FINGER TOOL
90
BS2483
MAGNETO FLYWHEEL PULLER (M24 X P1.0)
30
BS1040
BATTERY ACID LIQUID FILLER
9
BS2484
MAGNETO FLYWHEEL PULLER (M28 X P1.0)
30
BS1130
3PC DETAIL BRUSH SET
103
BS2485
MAGNETO FLYWHEEL PULLER (M30 X P1.25)
30
BS1164
DRIVE CHAIN TENSION PULLER
61
BS2486
MAGNETO FLYWHEEL PULLER (M32 X P1.5)
30
BS1234
4PC HANDY PICK & HOOK SET (76mm)
93
BS2487
MAGNETO FLYWHEEL PULLER (M35 X P1.0)
30
BS1235
2PC SEAL PICK SET
93
BS2488
MAGNETO FLYWHEEL PULLER (M38 X P1.5)
30
BS12900
SPARK COIL REMOVAL TOOL -BMW R259
10
BS2489
MAGNETO FLYWHEEL PULLER (M42 X P1.5)
30
BS12901
SPARK COIL REMOVAL TOOL -BMW R, F & K SERIES
10
BS2493
STARTER GEAR NUT WRENCH
27
BS1298
6PC SPARK PLUG MAINTENANCE KIT
23
BS2494
MAGNETO FLYWHEEL PULLER (M50 X P1.5)
30
BS1600
T-HANDLE SOCKET WRENCH HANGER
78
BS2501
OIL FILTER & CLUTCH HUB SPANNER
99
BS1601
T-HANDLE SOCKET WRENCH HOLDER
78
BS2551
FLEXIBLE SPOUT FUNNEL
104
BS1660
8PC T-HANDLE SOCKET WRENCH SET (300mm)
78
BS2865
7” RETAINING & SNAP RING PLIERS (INTERNAL STRAIGHT)
97
BS1660A
8PC T-HANDLE SOCKET WRENCH SPEED RING SET (300mm)
79
BS2866
7” RETAINING & SNAP RING PLIERS (INTERNAL 90 ANGLE)
97
BS1700
4PC T-HANDLE SPEED RING SET
79
BS2867
7” RETAINING & SNAP RING PLIERS (EXTERNAL SRTAIGHT)
97
BS1814
WIRE TERMINAL TOOL
8
BS2868
7” RETAINING & SNAP RING PLIERS (EXTERNAL 90 ANGLE)
97
BS1815
WIRE TERMINAL TOOL
8
BS2904
DOUBLE EAR HOSE CLAMP PLIERS
96
BS2008
FLEXIBLE HOSE CLAMP NUT DRIVER
98
BS3000
38
BS2110
VACUUM HOSE REMOVAL PLIERS
95
DOUBLE ENDED COUNTER BALANCER & CLUTCH HUB
SPANNER
BS2201
6PC TAPPET ADJUSTING TOOL SET
19
BS30008
CRANKSHAFT IN TDC POSITION TIMING TOOL FOR DUCATI
39
BS2250
PISTON LOCATION TOOL (M10 X P1.0)
24
BS30009
ALTERNATOR COVER PULLER FOR DUCATI 1199
31
BS2251
PISTON LOCATION TOOL (M12 X P1.0)
24
BS3001
COUNTER BALANCER & CLUTCH HUB SPANNER (IDΦ20.5mm)
38
BS2260
REINFORCED PLASTIC SUPER SCRAPER (15mm)
86
BS30010
CRANK SHAFT TURNING TOOL FOR DUCATI 1199
40
BS2261
REINFORCED PLASTIC SUPER SCRAPER (30mm)
86
BS30011
4PC BELT ROLLER TIMING ALIGNMENT TOOL (M5)
40
BS2262
REINFORCED PLASTIC SUPER SCRAPER (50mm)
86
BS30012
2PC BELT ROLLER TIMING ALIGNMENT TOOL (M6)
41
BS2300
CRANKCASE SEPARATOR TOOL SET
20
BS30013
2PC BELT ROLLER TIMING ALIGNMENT TOOL (M8)
41
BS2302
TIMING PLUG WRENCH
17
BS3002
COUNTER BALANCER & CLUTCH HUB SPANNER (IDΦ17.5mm)
38
BS23021
DUCATI ALTERNATOR COVER PULLER
11
BS3003
COUNTER BALANCER & CLUTCH HUB SPANNER (IDΦ24mm)
38
BS23050
DUCATI CRANK SHAFT TURNING TOOL
11
BS3004
COUNTER BALANCER & CLUTCH HUB SPANNER (IDΦ12.5mm)
38
BS2311
STUD REMOVE & INSTALL TOOL (M6 X P1.0)
17
BS3008
38
BS2312
STUD REMOVE & INSTALL TOOL (M8 X P1.25)
17
DOUBLE ENDED COUNTER BALANCER & CLUTCH HUB
SPANNER
BS2313
STUD REMOVE & INSTALL TOOL (M10 X P1.25)
17
BS3009
COUNTER BALANCER & CLUTCH HUB SPANNER (IDΦ29mm)
38
BS2314
STUD REMOVE & INSTALL TOOL (M10 X P1.5)
17
BS3032
PISTON RING COMPRESSOR SET
18
BS2401
MAGNETO FLYWHEEL PULLER (M14 X P1.5)
28
BS3039
PISTON RING PLIERS
18
BS2402
MAGNETO FLYWHEEL PULLER (M16 X P1.5)
28
BS3074
PISTON LOCATION TOOL (M14 X P1.25)
24
BS2403
MAGNETO FLYWHEEL PULLER (M18 X P1.5)
28
BS3101
STEERING STEM & FRONT FORK CAP WRENCH (46mm X
50mm)
48
BS2404
MAGNETO FLYWHEEL PULLER (M20 X P1.5)
28
BS3102
MAGNETO FLYWHEEL PULLER (M22 X P1.5)
28
STEERING STEM & FRONT FORK CAP WRENCH (49mm X
50mm)
48
BS2405
BS2421
MAGNETO FLYWHEEL PULLER (M18 X P1.5)
28
BS3105
FEELER GAUGE 16 BLADE METRIC/ SAE
19
BS2422
MAGNETO FLYWHEEL PULLER (M18 X P1.5)
28
BS3112
UNIVERSAL PULLEY HOLDER WRENCH SET
39
BS2423
MAGNETO FLYWHEEL PULLER (M20 X P1.5)
28
BS32100
2” FUNCTIONAL TYRE INFLATOR DIAL GAUGE
62
BS2424
MAGNETO FLYWHEEL PULLER (M20 X P1.5)
28
BS3211
3 IN 1 FUNCTIONAL TYRE GAUGE
70
BS2441
MAGNETO FLYWHEEL PULLER (M19 X P1.5)
29
BS3238
DIGITAL TYRE PRESSURE GAUGE
69
BS2442
MAGNETO FLYWHEEL PULLER (M24 X P1.0)
29
BS3356
CLIC-R TYPE HOSE CLAMP PLIERS
95
BS2443
MAGNETO FLYWHEEL PULLER (M27 X P1.0)
29
BS3500
CHAIN EXTRACTOR
60
BS2444
MAGNETO FLYWHEEL PULLER (M27 X P1.25)
29
BS3506
CHAIN LINK PLIERS
61
BS2460
STARTER FLYWHEEL PULLER
27
BS3510
PROFESSIONAL CHAIN REPAIRING MASTER SET
59
BS2461
MAGNETO FLYWHEEL PULLER (M24 X P1.5)
30
BS35101
UNIVERSAL CHAIN REPAIRING MASTER SET
59
INDEX
Item No.
Page.
Item No.
BS3550
CAM CHAIN BREAKER AND RIVETING TOOL KIT
21
BS5612
CURVE TYPE TYRE LEVER
67
BS3699
TYRE VALVE EXTRACTOR BAR
70
BS5630
BRAKE FLUID TESTER
57
BS3701
TYRE BEAD HOLDING TOOL
68
BS5800
BRAKE PISTON DETACHING TOOL
56
BS3913
FLYWHEEL PULLER KIT
33
BS6012
8PC MULTI DRIVER WRENCH SET
88
BS3949
VALVE CORE TORQUE TOOL
69
BS6012A
MULTI DRIVER WRENCHES (6mm)
88
BS4008
SEAL AND BEARING RETAINER TOOL (40mm , 4 PINS)
73
BS6012B
MULTI DRIVER WRENCHES (8mm)
88
BS4009
SEAL AND BEARING RETAINER TOOL (40mm , 4 PINS AND 1
NOTCH)
73
BS6012C
MULTI DRIVER WRENCHES (10mm)
88
BS6012D
MULTI DRIVER WRENCHES (12mm)
88
BS4010
SEAL AND BEARING RETAINER TOOL (44mm , 6 POINT)
73
BS6012E
MULTI DRIVER WRENCHES (13mm)
88
BS4011
SEAL AND BEARING RETAINER TOOL (47mm , 6 POINT)
73
BS6012F
MULTI DRIVER WRENCHES (14mm)
88
BS4012
TOP FRONT FORK HEX NUT WRENCH (35mm)
45
BS6012G
MULTI DRIVER WRENCHES (17mm)
88
BS4013
TOP FRONT FORK HEX NUT WRENCH (36mm)
45
BS6012H
MULTI DRIVER WRENCHES (19mm)
88
BS4014
TOP FRONT FORK HEX NUT WRENCH (39mm)
45
BS6050
HANDY PANEL REMOVAL TOOL
86
BS4017
MECHANICAL BEARING PULLER SET
106
BS6100
PORTABLE WORKING STOOL
108
BS4018
SEAL AND BEARING RETAINER TOOL (36mm , 4 POINT)
73
BS6101
TAILPIPE EXPANDER (29~44mm)
14
BS4019
DUCATI STEERING STEM NUT TOOL
43
BS6103
TAILPIPE EXPANDER (38~64mm)
14
BS4030
OCTAGONAL FRONT FORK CAP TOOL (45mm)
43
BS6105
TAILPIPE EXPANDER (54~89mm)
14
BS4031
OCTAGONAL FRONT FORK CAP TOOL (46mm, FOR SHOWA)
43
BS6300
9PC MAGNETIC TX-STAR KEY SET
85
BS4032
OCTAGONAL FRONT FORK CAP TOOL (49mm)
43
BS6502
PRESSURE ADJUSTING POWER CLAMP
87
BS4033
OCTAGONAL FRONT FORK CAP TOOL (50mm, FOR SHOWA)
43
BS6656
UNIVERSAL 3 LEG OIL FILTER WRENCH (63~99mm)
24
BS4051
KYB TWIN CHAMBER FORK COMPRESSION TOOL (36mm)
44
BS6659
8PC CUP OIL FILTER WRENCH SET
25
BS4052
KYB TWIN CHAMBER FORK COMPRESSION TOOL (32mm)
44
BS6661
CUP OIL FILTER WRENCH (65-14F)
25
BS4100
HYDRAULIC COIL SPRING COMPRESSOR TOOL
50
BS6663
CUP OIL FILTER WRENCH (68mm-14F)
25
BS4107
VACUUM SWITCH SOCKET (22mm)
22
BS6664
CUP OIL FILTER WRENCH (74mm-15F)
25
BS4107A
VACUUM SWITCH SOCKET (11/16”)
22
BS6665
CUP OIL FILTER WRENCH (76mm-8F)
25
BS41500
FORK OIL LEVEL GAUGE TOOL
44
BS6666
CUP OIL FILTER WRENCH (76mm-12F)
25
BS4201
STEERING BEARING OUTER RACE REMOVER TOOL
45
BS6667
CUP OIL FILTER WRENCH (76mm-14F)
25
BS4224
OXYGEN SENSOR SOCKET TOOL (11/16”)
22
BS6669
CUP OIL FILTER WRENCH (80mm-15F)
25
BS4224C
OXYGEN SENSOR SOCKET TOOL (22mm)
22
BS6670
CUP OIL FILTER WRENCH (82mm-15F)
25
BS4326
PORTABLE BEARING PACKER
101
BS6728
HEAVY DUTY PULLEY HOLDER WRENCH (25~160mm)
34
BS4328
STUD SETTER & EXTRACTOR
21
BS67500
HARLEY-DAVIDSON CLUTCH SPRING COMPRESSOR TOOL
103
BS4400
STEERING STEM & FRONT FORK CAP ADJUSTING WRENCH
(30mm X 32mm)
46
BS70002
MOTORCYCLE CHAIN MAINTENANCE SET
60
BS4401
FRONT FORK CAP ADJUSTING WRENCH WITH ADDITION
DRIVER (17mm X 24mm)
46
BS7030
FLEXIBLE MAGNETIC CLAW PICK UP TOOL (700mm)
90
BS7288
1/4” SQUARE DRIVE RATCHET HANDLE
81
FRONT FORK CAP ADJUSTING WRENCH WITH ADDITION
DRIVER (17mm X 27mm)
46
BS7289
3/8” SQUARE DRIVE RATCHET HANDLE
81
BS7291
1/2” SQUARE DRIVE RATCHET HANDLE
81
FRONT FORK CAP ADJUSTING WRENCH WITH ADDITION
DRIVER (19mm X 24mm)
46
BS7352
8PC RATCHET WRENCH SET METRIC - STUBBY FLEX HEAD
89
BS7352A
STUBBY FLEXIBLE RATCHET WRENCH (8mm)
89
FRONT FORK CAP ADJUSTING WRENCH WITH ADDITION
DRIVER (19mm X 27mm)
46
BS7352B
STUBBY FLEXIBLE RATCHET WRENCH (10mm)
89
BS7352C
STUBBY FLEXIBLE RATCHET WRENCH (12mm)
89
BS7352D
STUBBY FLEXIBLE RATCHET WRENCH (13mm)
89
BS7352E
STUBBY FLEXIBLE RATCHET WRENCH (14mm)
89
BS7352F
STUBBY FLEXIBLE RATCHET WRENCH (17mm)
89
BS4402
BS4403
BS4404
BS4405
Product
Product
Page.
FRONT FORK CAP ADJUSTING WRENCH WITH ADDITION
DRIVER (22mm X 27mm)
46
FRONT FORK CAP ADJUSTING WRENCH WITH ADDITION
DRIVER (22mm X 32mm)
46
BS4531
CABLE WIRE LUBRICATION TOOL
101
BS7352G
STUBBY FLEXIBLE RATCHET WRENCH (19mm)
89
BS4532
BELT TENSION GAUGE
33
BS7352H
STUBBY FLEXIBLE RATCHET WRENCH (6mm)
89
BS5000
FRONT FORK & SHOCK VICE
50
BS7356
TORQUE ANGLE GAUGE
99
BS50006
FORK CAP SOCKET FOR OHLINS 50mm FORK
53
BS7407
RATCHET WRENCH
89
BS50007
FORK CAP SOCKET FOR OHLINS MECHATRONICS FORK
53
BS7407A
RATCHET WRENCH (8mm)
89
BS50008
FORK CAP SOCKET FOR MARZOCCHI FORK
53
BS7407B
RATCHET WRENCH (10mm)
89
BS50009
FORK CAP SOCKET FOR SACHS FORK
53
BS7407C
RATCHET WRENCH (12mm)
89
BS5201
U HOOK HANDLE (195mm)
92
BS7407D
RATCHET WRENCH (13mm)
89
BS5420
1/2” DRIVE TELESCOPIC RATCHET
82
BS7407E
RATCHET WRENCH (14mm)
89
BS5421
1/4” SQ. DR. DIGITAL READING TORQUE WRENCH (10-50Nm)
82
BS7407F
RATCHET WRENCH (17mm)
89
BS5422
3/8” SQ. DR. DIGITAL READING TORQUE WRENCH (20-100Nm)
82
BS7407G
RATCHET WRENCH (19mm)
89
BS5423
1/2” SQ. DR. DIGITAL READING TORQUE WRENCH (40-200Nm)
82
BS7407H
RATCHET WRENCH (6mm)
89
BS5501
WHEEL TURNING & BALANCE STAND
71
BS80005
LOCKING PLIER
97
BS5502
22PC SPOKE TORQUE WRENCH SET 4FT/POUND
72
BS8001
CYLINDER COMPRESSION TEST KIT
26
BS5503
22PC SPOKE TORQUE WRENCH SET 4FT/POUND
72
BS80013
DEAD BLOW HAmmER (35mm DIA.)
108
BS5510
MULTI-FUNCTION TYRE VALVE TOOL
62
BS80016
1/2”DR UNIVERSAL JOINT T-HANDLE WRENCH
81
BS5530
FRONT WHEEL SPINDLE REMOVE TOOL
50
BS80017
3/8”DR UNIVERSAL JOINT T-HANDLE WRENCH
81
BS55301
DUCATI FRONT AXLE ALIGNMENT TOOL (SHOWA 25mm)
63
BS80018
1/4”DR UNIVERSAL JOINT T-HANDLE WRENCH
81
BS55302
DUCATI FRONT AXLE ALIGNMENT TOOL (OHLINS 25mm)
63
BS80019
1-7/8” / 47mm RETRACTABLE TIE DOWN
105
BS55303
DUCATI FRONT AXLE ALIGNMENT TOOL (OHLINS 30mm)
63
BS8002
CYLINDER LEAKAGE TESTER KIT
26
BS5531
FRONT WHEEL SPINDLE REMOVAL TOOL (14mm HEX )
64
BS80031
1”/25mm RETRACTABLE RATCHET TIE DOWN SET (L 2.4M)
105
BS5532
FRONT WHEEL SPINDLE REMOVAL TOOL (19mm HEX )
64
BS80032
1”/25mm RETRACTABLE RATCHET TIE DOWN SET (L 1.8M)
105
BS5535
WHEEL BEARING REMOVAL TOOL SET
64
BS80034
1”/25mm RETRACTABLE RATCHET TIE DOWN SET (L 4.5M)
105
BS5550
DUCATI REAR WHEEL NUT SOCKET (41/46mm)
65
BS80054
BEARING MAINTENANCE SET (METRIC)
107
BS5551
DUCATI WHEEL NUT SOCKET (30/55mm)
65
BS80055
BEARING MAINTENANCE SYSTEM (INCH)
107
BS5552
MV AGUSTA WHEEL NUT SOCKET (26/56mm)
65
BS80056
12PC MULTI-FUNCTION RATCHET WRENCH SET
98
BS5553
DUCATI FRONT WHEEL NUT SOCKET ( 28/30mm)
65
BS80057
3 IN 1 VERSATILITY WORKING MAT
108
BS5582
VACUUM PUMP & BRAKE BLEEDER KIT
55
BS8006
4.0L PORTABLE OIL DRAIN CAN
104
BS5603
TYRE LEVER (200mm)
67
BS8008
TYRE CHANGE EXTRUDER TOOL
68
BS5604
TYRE LEVER (400mm)
67
BS8117
CARBURETOR SYCHRONIZER VACUUM GAUGE SET
15
BS5610
TYRE BEAD HOLDING CLAMP
68
BS4406
INDEX
Item No.
Product
Item No.
Product
BS9035
2PC RUBBER LINE CLAMP SET
Page.
94
BS9950
FLYWHEEL PULLER KIT
Page.
34
BS9036
HOSE CLAMP PLIERS (3~12mm)
94
BS9952
3PC RIM PROTECTOR SET
66
BS9037
HOSE CLAMP PLIERS (3.5~18mm)
94
BS9953
TYRE LEVER (280mm)
66
BS9041
HOSE CLAMP PLIERS (4~28mm)
94
BS9960
BIKESERVICE ROTATABLE DISPLAY STAND
109
BS9101
9PC TX-STAR EXTRA-LONG SHAFT KEY SET
84
BSG01685-03
T HANDLE HEX WRENCH (3 X 125mm)
80
BS9102
9PC MAGNETIC BALL POINT HEX KEY SET
85
BSG01685-05
T HANDLE HEX WRENCH (4 X 180mm)
80
BS9103
9PC HEX EXTRA-LONG SHAFT KEY SET
84
BSG01685-07
T HANDLE HEX WRENCH (5 X 180mm)
80
BS9132
EXTRA THIN WALL SPARK PLUG SOCKET (14mm)
10
BSG01685-08
T HANDLE HEX WRENCH (6 X 210mm)
80
BS9133
EXTRA THIN WALL SPARK PLUG SOCKET (16mm)
10
BSG01685-10
T HANDLE HEX WRENCH (8 X 250mm)
80
BS9134
EXTRA THIN WALL SPARK PLUG SOCKET (18mm)
10
BSG01685-11
T HANDLE HEX WRENCH (10 X 300mm)
80
BS9135
EXTRA THIN WALL SPARK PLUG SOCKET (20.8mm)
10
BSG01685-12
T HANDLE HEX WRENCH (12 X 320mm)
80
BS91400
UNIVERSAL BEARING RACE AND SEAL INSTALL TOOL
100
BSG01685-13
T HANDLE HEX WRENCH (14 X 340mm)
80
BS9144
17PC BUSHING DRIVE SET (METRIC)
106
BSG01686-05
T HANDLE TORQUE WRENCH (T25 X 180mm)
80
BS9145
19PC BUSHING DRIVE SET (SAE)
106
BSG01686-06
T HANDLE TORQUE WRENCH (T27 X 180mm)
80
BS9314
STAINLESS CUTTING SCISSORES
96
BSG01686-07
T HANDLE TORQUE WRENCH (T30 X 180mm)
80
BS9404
MAGNETIC STORAGE TRAYS (240X140mm)
83
BSG01686-08
T HANDLE TORQUE WRENCH (T40 X 210mm)
80
BS9434
MAGNETIC STORAGE TRAYS (4”, ROUND)
83
BSG01686-09
T HANDLE TORQUE WRENCH (T45 X 210mm)
80
BS9470
SAFETY WIRE TWIST PLIERS
91
BSG01686-10
T HANDLE TORQUE WRENCH (T50 X 210 mm)
80
BS9484
PROFESSIONAL WIRE STRIPPER
8
BSG02840
6” SAFETY WIRE TWISTING PLIER WITH RESERSIBLE
91
BS9500
WATERPROOF WORKING APRON
109
BS9506
ALLOY WHEEL CLEANING BRUSH
103
BS9621
4PC STUBBY SCREWDRIVER SET
87
BS9651
IMPACT DRIVER SET
88
BS9725
PROFESSIONAL PERSONAL TOOL PACK
102
BS9728
EASY HANDY TOOL PACK
102
BS9730
3PC HEX BIT SOCKETS (H8,H10,H12mm)
51
BS9731
3PC TX-STAR BIT SOCKET (T45,T50,T55)
51
BS9732
3PC SPLINE BIT SOCKET (M8,M10,M12)
51
BS9827A
FRONT FORK DUST SEAL DRIVER (32mm)
47
BS9827B
FRONT FORK DUST SEAL DRIVER (33mm)
47
BS9827C
FRONT FORK DUST SEAL DRIVER (35mm)
47
BS9827D
FRONT FORK DUST SEAL DRIVER (36mm)
47
BS9827E
FRONT FORK DUST SEAL DRIVER (37mm)
47
BS9827F
FRONT FORK DUST SEAL DRIVER (38mm)
47
BS9827G
FRONT FORK DUST SEAL DRIVER (39mm)
47
BS9827H
FRONT FORK DUST SEAL DRIVER (40mm)
47
BS9827J
FRONT FORK DUST SEAL DRIVER (41mm)
47
BS9827K
FRONT FORK DUST SEAL DRIVER (43mm)
47
BS9827L
FRONT FORK DUST SEAL DRIVER (45mm)
47
BS9827M
FRONT FORK DUST SEAL DRIVER (46mm)
47
BS9827N
FRONT FORK DUST SEAL DRIVER (48mm)
47
BS9827P
FRONT FORK DUST SEAL DRIVER (50mm)
47
BS9827Q
FRONT FORK DUST SEAL DRIVER (27mm)
47
BS9827R
FRONT FORK DUST SEAL DRIVER (30mm)
47
BS9827S
FRONT FORK DUST SEAL DRIVER (31mm)
47
BS9827T
FRONT FORK DUST SEAL DRIVER (34mm)
47
BS9827U
FRONT FORK DUST SEAL DRIVER (42mm)
47
BS9827V
FRONT FORK DUST SEAL DRIVER (47mm)
47
BS9827W
FRONT FORK DUST SEAL DRIVER (49mm)
47
BS9828
VALVE SPRING COLLET REMOVER TOOL (Φ18mm X Φ9mm)
20
BS9829
VALVE SPRING COLLET REMOVER TOOL (Φ14.5mm X Φ7mm)
20
BS9835
ACCELERATOR AND CLUTCH CABLE WIRE REPLACEMENT
TOOL
92
BS9836
M5 BRAKE CABLE WIRE REPLACE TOOL
92
BS9838
M6 BRAKE CABLE WIRE REPLACE TOOL
92
BS9839
MASTER MECHANICS TOOL KIT
75
BS9853
DUAL END BI-HEX PULLEY NUT WRENCH (14 & 17mm)
35
BS9854
FLAT TYPE CLUTCH OUTER HOLDING WRENCH
36
BS9855
CLUTCH OUTER HOLDING WRENCH
36
BS9856
PULLEY & CLUTCH 12-POINT LOCKING WRENCH (32mm)
37
BS9857
PULLEY & CLUTCH 6-POINT LOCKING WRENCH (29mm)
37
BS9858
PULLEY & CLUTCH 3-POINT LOCKING WRENCH (26mm)
37
BS9859
PULLEY & CLUTCH LOCKING NUT WRENCH (45mm)
36
BS9861
CLUTCH NUT WRENCH (34 X 59mm)
35
BS9862
CLUTCH NUT WRENCH (39 X 59mm)
35
BS9863
CLUTCH NUT WRENCH (41 X 59mm)
35
BS9864
CLUTCH NUT WRENCH (46 X 72mm)
35
BS9870
DISC PAD BRAKE SPREADER (30mm)
56
BS9871
DISC PAD BRAKE SPREADER (65mm)
56
BS9892
STEERING TUBE BEARING PULLER TOOL SET
49
BS9893
STEERING TUBE BEARING INSTALLER TOOL SET
49
BS98940
STEERING HEAD BEARING INSTALLER TOOL SET
52
BS9947
HEAVY-DUTY VALVE SPRING COMPRESSOR KIT
25
About BIKESERVICE
ONLY MOTORCYCLE REPAIRING SERVICE AND
RELIABLE SERVICE TOOL ONLY
Bikeservice, founded by Apo Tool International Ltd, is the leading
specialty tool company in Taiwan with experience and knowledge
specialized in motorcycle after-service.
Never like others, Bikeservice understands that
ONLY MOTORCYCLE SERVICE TOOLS CAN 100%
ACCURATELY REPAIRING MOTORCYCLE,BUT NOT
AUTOMOTIVE TOOLS.
NOT ONLY A MANUFACTURER, BUT A DESIGN HOUSE
With pioneering spirit, Bikeservice starts by big research of
motorcycles and existing tools in the market. We fully understand
the function, strong point, defect, dimension, material of different
tools and establish our own database. All above for Bikeservice is
to design the tness, create new and provide the most accurate
and suitable tools for motorcycle repairing service.
NOT ONLY A DESIGN HOUSE,
BUT AN INVENTOR
Bikeservice believes that the best tool should be
simply understood, easily used and well functional.
We never stop researching, creating and improving
in order to invent tools for all different generation
and for better motorcycle repairing.
Bikeservice, the most reliable connection between
all human being and motorcycle.
BS1030
171PC HEAT SHRINK TUBE SET
Provides superior protec on and insula on of components and wires
Adhesive lined inner wall seals against water and moisture, preven ng
corrosion
Quick and simple to shrink using heat gun
Colour coordinated sizes
Opera ng temperature: -55°C~125°C
Minimum shrink temperature: 70°C
Minimum full recovery temperature: 110°C
Shrink ra o: 2:1. (Meet Sony and ROHS requirements)
ELECTRIC STSTEM SERVICE TOOLS
BS1031
106PC WATERPROOF HEAT SHRINK TUBE SET
Provides superior protec on and insula on of components
and wires
Adhesive double-lined inner wall provides complete
waterproofing, preven ng corrosion
Quick and simple to shrink using heat gun
Ideal for applica ons where exposure to moisture may occur
Opera ng temperature: -45°C~125°C
Minimum shrink temperature: 70°C
Minimum full recovery temperature: 120°C
Shrink ra o: 3:1. (Meet Sony and ROHS requirements)
7
BSA01814
BS1814
BS1815
WIRE TERMINAL TOOL
Designed for easy removal of terminals and wires from electrical
connectors
Reduces risk of damage to wires, terminals and connectors
Rectangular blades for pack-con terminals, flat blade to open connectors, fork for ALDL connector
Prongs depress the “barbs” on conven onal terminals
All metal construc on ensures strength and rigidity on stubborn
connectors
BS9484
PROFESSIONAL WIRE STRIPPER
Tool with plier nose and wire cu er
Designed for stripping and cu翿 ng copper and aluminium wires
Heat treated alloy steel
BS1020
2PC BATTERY TERMINAL CLEANING TOOL KIT
Pick
Stainless Steel
Clean Brush
Scraper
Gapper
5 func ons for ideal ba ery maintenance
Help quickly and easily remove corrosion and dirt from cable
clamps and terminal posts
BATTERY ACID LIQUID FILLER
ELECTRIC STSTEM SERVICE TOOLS
BS1040
Provides a safe and e翿 cient way to fill dry charged batteries
Avoids spilling and damage in confined spaces
Thumb release controls acid flow
Ba ery full indica on
BS12900
BS12901
SPARK COIL REMOVAL TOOL
-BMW R25
SPARK COIL REMOVAL TOOL BMW R, F & K SERIES
Designed to release the spark plug high tension coil
Simple and effec ve tool to eliminate the possibility
of damage to the coil assembly during removal
Made from AL6061-T6
Suits BMW R259 single spark igni on systems (All
R1100 and R1150 models before 2003 model year)
Designed to release the spark plug high tension coil
Simple and effec ve tool to eliminate the possibility of
damage to the coil assembly during removal
Made from AL6061-T6
Suits BMW R1150 twin spark models (2004 and later),
All R1200 models (except R1200 C and CL), All F800
models plus F650 GS Twin, K1200 S, R, R-Sport, K1300
S, R and GT
BS9132
14mm
BS9133
16mm
BS9134
18mm
BS9135
20.8mm
EXTRA THIN WALL SPARK PLUG SOCKET
Hardened chrome vanadium steel with inbuilt rubber
insert to hold plug during installa on
Extra thin wall bi-hex sockets designed to access narrow
spark plug holes
10
BS23021
DUCATI ALTERNATOR COVER PULLER
Twin-pull style puller used to remove the alternator cover from
DUCATI Motorcycles
Eliminates the need for prying or impact tools to remove cover
Ideal tool for general inspec ons or for installing a lightweight
flywheel
Used with 17mm hex driver
Made from AL6061-T6
Suits all modern DUCATI motorcycles
DUCATI CRANK SHAFT TURNING TOOL
Enables rota on of the engine safely during valve clearance
check or ming se翿 ng
Used with 6mm hex key and 17mm hex driver
Made from chrome molybdenum alloy steel for durability
and long service life
Fits all DUCATI’s from 1990-2011
ELECTRIC STSTEM SERVICE TOOLS
BS23050
11
BS0058
CARBURETOR ADJUSTING TOOL SET
Designed for special angled and hard-to-reach carburetor
Available for most mul -cylinder motorcycles
Contents:
1. 90° Angled Slot Blade Adaptor
2. 90°Angled Bit Holder Adaptor
3. 40mm (L) D Type Socket Bit
4. 35mm (L) PH2 Bit
5. 58mm (L) PH2 Bit
6. 35mm (L) Flat 5mm Bit
7. 58mm (L) Flat 5mm Bit
8. 95mm (L) Flat 5mm Bit
9. Auxiliary Handle
BS0231
BS0231
PARALLEL TIP SLOT CARBURETOR ADJUSTING
SCREW DRIVER (250mm)
BS0059
FUEL INJECTION AND CARBURETION TOOLS
BS0059
D TYPE SOCKET CARBURETOR ADJUSTING
DRIVER (165mm)
Finger snap driver handle makes sensi ve carburetor adjusting work easier
13
BS6101
TAILPIPE EXPANDER (29~44mm)
BS6103
TAILPIPE EXPANDER (38~64mm)
BS6105
TAILPIPE EXPANDER (54~89mm)
An internal expanding designed tool operates with wrench for all
tail pipe expanding
Inside hex nut expands out the sides or pushes out the crimps
Extra long hex rod for be er drive delivery
14
BS8117
CARBURETOR SYCHRONIZER VACUUM GAUGE SET
Adjusting Valve
FUEL INJECTION AND CARBURETION TOOLS
This vacuum gauge set contains precision gauges, each with its
own damping control
Gauges are mounted to a portable heavy duty metal base for
bench top use
Suitable for mul carburetor balancing
Contents:
4pc 2” vacuum gauge with fixed plate
4pc rubber hose ( O.D )Φ8 mm x ( I.D )Φ5 mm x ( Length ) 120 cm
Connec ng adaptor
4pcΦ6 mm – 55mm (L)
4pc M5 x P0.8 – 55mm (L)
4pc M6 x P0.75 – 55mm (L)
4pc M6 x P1.0-60mm (L)
Extension tube:
4pc M5xP0.8-100m(L)
4pc M5xP0.8-165mm(L)
Accessories:
2pc Air valve
4pc O-ring
4pc Tube clamp
Tube Clamp and Rings
15
BS2302
TIMING PLUG WRENCH
Designed for removal and replacement of straight slot ming and
inspec on plugs
Suits HONDA, Kawasaki, SUZUKI, YAMAHA etc
Blade sizes 16mm (5/8”), 22mm (7/8”) and 38mm (1-1/2”)
BS2312
M6 X P1.0
M X P1.25
BS2313
BS2314
M10 X P1.25
ENGINE SYSTEM TOOLS
BS2311
M10 X P1.5
STUD REMOVE & INSTALL TOOL
Easily removes and installs studs without damaging threads
Suitable for most popular stud thread sizes
17
BS3032
PISTON RING COMPRESSOR SET
Pliers can be used parallel or perpendicular to the cylinder block,
angles opera on designed pliers
Ratche ng func on handle holds the compressing rings in posion for easy installa on of pis on rings
Installs piston rings from 35mm~111mm ( 1-3/8” ~ 4-3/8” )
Piston Ring Compressing Pliers
Piston Ring Pliers
Compress Working Capacity:
35mm~41mm ( 1-3/8" ~ 1-5/8" ).
41mm~47mm (1-5/8”~1-27/32”).
47mm~53mm (1-27/32"~2-3/32").
53mm~59mm (2-3/32"~2-5/16").
59mm~66mm (2-5/16"~2-5/8").
66mm~73mm (2-5/8"~2-7/8").
73mm~ 79mm (2-7/8"~3-1/8").
79mm~ 86mm (3-1/8"~3-3/8").
86mm~ 92mm (3-3/8"~3-5/8").
92mm~ 98mm (3-5/8"~3-7/8").
98mm~105mm (3-7/8"~4-1/8").
105mm~111mm (4-1/8"~4-3/8").
~
~
BS3039
PISTON RING PLIERS
1
Tapered jaws hold and expand piston ring easily over piston block
Ratche ng func on handle holds piston rings steady for removal
or installa on
BS2201
6PC TAPPET ADJUSTING TOOL SET
Includes 3 size wrenches: 8mm, 9mm, 10mm
Includes 3 adjusters: flat screw type, 3mm and 4mm square type
Replaceable adjusters and wrenches for nine different combinaons
Fits most motorcycles and ATVs tappet adjus ng
BS2201-01 3mm Square
BS2201-02 4mm Square
BS2201-03 8mm Hex
BS2201-04 9mm Hex
BS2201-05 10mm Hex
BS2201-06 Flat Screw
Size Range
SAE
0.002
0.003
0.004
0.006
0.008
0.01
0.012
0.015
ENGINE SYSTEM TOOLS
Metric
0.05
0.08
0.1
0.15
0.2
0.25
0.3
0.38
BS3105
FEELER GAUGE 16 BLADE METRIC/ SAE
16 stainless steel blades
Tapered blade design
Metric and SAE sizing
Metric size range: 0.05mm~0.38mm
SAE size range: 0.002”~0.015”
1
BS9828
BS9829
BS9828
Φ
Φ (Φ 18mm X Φ 9mm)
VALVE SPRING COLLET REMOVER
TOOL
BS9829
VALVE SPRING COLLET REMOVER TOOL
Φ X 7mm, HOLLOW
Φ
(Φ Φ14.5mm
Φ 5mm)
Removes split collets when compressing valve springs on 4 stroke
engines
Holds valve spring collets in posi on during replacement
Suits most 4 stroke motorcycle engines
BS2300
CRANKCASE SEPARATOR TOOL SET
Suits most two and four stroke engines with ver cally split
crankcase
Movable fingers allow mul tude of bolt pa erns
Includes moun ng bolts, centre pulling bolt and three leg
frame
20
BS3550
CAM CHAIN BREAKER AND RIVETING TOOL KIT
Compact tool kit for quick and trouble free cam chain replacement
Provides the ability to break and rivet cam chain master links
Ideal companion during major servicing and engine overhauls
Forged hardened alloy steel body and components
Includes body, handle and push pins
Suits chain plate quan ty: 2x3, 3x4, 4x5
Instruc on manual included
ENGINE SYSTEM TOOLS
BS4328
STUD SETTER & EXTRACTOR
Powerful grip for stubborn or rusted threads, or for se翿 ng
new ones
21
BS4107
VACUUM SWITCH SOCKET (22mm)
BS4107A
VACUUM SWITCH SOCKET (11/16”)
22mm (7/8”) and 11/16” hex flare nut socket for vacuum switch
and oxygen sensor service on computer controlled engines
3/8” Sq. Dr.
BS4224
OXYGEN SENSOR SOCKET TOOL (11/16”)
BS4224C
OXYGEN SENSOR SOCKET TOOL (22mm)
This tool is used to remove or install the 22mm (7/8”) and 11/16”
hex oxygen sensor on all closed loop fuel injected models
3/8” Sq. Dr.
22
BS0244
COOLING SYSTEM & RADIATOR PRESSURE TEST SET
Hand operated pump builds and displays pressure quickly to locate leaks in cooling and radiator systems
Convenient push-bu on valve safely relieves pressure when testing is completed
2.5 Bar (35psi) Pressure Hand Pump
Radiator Cap Test Adaptor For
With Gauge in PSI and bar unit.
TRIUMPH, DUCATI, BMW, APRILLI A
Radiator Tank Adaptor For
Radiator Cap Test Adaptor For
TRIUMPH, DUCATI, BMW, APRILLI A
HONDA, Kawasaki, SUZUKI, YAMAHA
Radiator Tank Adaptor For
Air
Pressure input adaptor for cap test
HONDA, Kawasaki, SUZUKI, YAMAHA
DUCATA
ENGINE SYSTEM TOOLS
BS1298
6PC SPARK PLUG MAINTENANCE KIT
Tapered edge sets spark plug gaps from 0.50mm to
2.25mm (0.020” to 0.100”)
Specially designed hole can adjust the gap width of the
spark plug without pressuring the centre electrode
Thin mini files designed for igni on points and electrode
cleaning
23
BS6656
UNIVERSAL 3 LEG OIL FILTER WRENCH (63~mm)
Allows easy removal of cartridge style oil filters even in ght
loca ons
Vinyl dipped legs minimize filter damage
Suits filters 63mm~99mm (2 1/2”~3 7/8”) diameter
3/8” Sq. Dr.
BS2250
M10 X P1.0
BS2251
M12 X P1.25
BS3074
M14 X P1.25
PISTON LOCATION TOOL
Insert the tool un l it touches the top of piston via the spark plug
hole when the piston is at bo om of stroke
Once installed, it holds the cranksha in place at top dead centre
24
BS6659
PC CUP OIL FILTER WRENCH SET
Complete dimension allows easy removal of installa on
Withstands up to 85 /1bs. of torque
Grip socket designed minimizes the possibility of crushing filters
Use 3/8” square driver with 19mm hex driver tools
Coated with electro-black oxide finish for rust-proof
BS6661: 65mm-14 Flute
BS6663: 68mm-14 Flute
BS6664: 74mm-15 Flute
BS6665: 76mm- 8 Flute
BS6666: 76mm-12 Flute
BS6667: 76mm-14 Flute
BS6669: 80mm-15 Flute
BS6670: 82mm-15 Flute
Throat (B)
Min. mm Max. mm
mm
20
135
110
ENGINE SYSTEM TOOLS
Jaw (A)
BS9947
HEAVY-DUTY VALVE SPRING COMPRESSOR KI
Suitable for small and large motorcycles
Durable fixed U-frame features strong ACME threads
Made from: SCM440
Adaptor sizes: 19, 23 and 25mm
25
BS8001
CYLINDER COMPRESSION TEST KIT
Designed specifically for tes ng motorcycle and small engine
compression
Features a specially designed compression gauge and hose assembly, plus three different size hose adaptors
Compression tester and hose lengths are designed for op mal
viewing from side of engine
Covers most popular motorcycle and small engine plug sizes
(16mm, 18mm, 21mm)
Corrosion resistant nickel plated finish
270mm (10-5/8”) flex hose gauge assembly with quick coupler
M10 hose for 16mm (5/8") spark plug.
M12 hose for 18mm spark plug.
M14 hose for 20.6mm (13/16") spark plug.
300 psi ( 20kg/cm 2 ) gauge.
Spare Parts.
BS8002
CYLINDER LEAKAGE TESTER KIT
Designed to check the amount of cylinder leakage in 4-stroke
engines
With an air input of 70-160 PSI
Pressures the cylinder with 60 PSI of air
Register the total percentage of leakage past the rings, head gasket, intake and exhaust valves
Speeds up troubleshoo ng and helps to isolate worn components
Covers plug sizes 16mm, 18mm, 21mm and M18 hose for vacuum
pump
26
Percentage of leakage gauge.
M10 hose for 16mm (5/8") spark plug.
M12 hose for 18mm spark plug .
M14 hose for 20.6mm (13/16") spark plug.
M18 hose for vacuum pump.
Spare O Ring
BS2460
STARTER FLYWHEEL PULLER
Removes the starter flywheel from the engine cranksha firmly
engages the sha
Size: 110mm long with 24mm x 1.00 pitch diameter female thread
Use with 3/8” Sq. Dr. or 19mm hex spanner and 30mm hex spanner
ENGINE SYSTEM TOOLS
BS2493
STARTER GEAR NUT WRENCH
Removes the starter gear from the engine cranksha
The offset opening engages the nut without engaging the sha
28.5mm x 40mm - 4 point x 65mm (depth)
1/2” Sq. Dr
27
1
2
3
4
5
MAGNETO FLYWHEEL PULLER
Thread puller designed for fixed-point type magneto flywheels
Chrome alloy steel ball p on sha to reduce fric on stress during
disassembly
1
BS2401M14 x P1.5
2
BS2402M16 x P1.5
3
BS2403M18 x P1.5
4
BS2404M20 x P1.5
5
BS2405M22 x P1.5
1
2
3
4
MAGNETO FLYWHEEL PULLER
Thread puller designed for fixed-point type magneto flywheels
Chrome alloy steel ball p on sha to reduce fric on stress during
disassembly
2
1
BS2421M18 x P1.5 x Φ12mm (16mm L)
2
BS2422M18 x P1.5 x Φ14mm (32mm L)
3
BS2423M20 x P1.5 x Φ14mm (15mm L)
4
BS2424M20 x P1.5 x Φ14mm (30mm L)
MAGNETO FLYWHEEL PULLER
Thread puller designed for fixed-point type magneto flywheels
Chrome alloy steel ball p on sha to reduce fric on stress during
disassembly
1
2
3
4
5
6
7
8
9
10
11
12
13
14
BS2441M19 x P1.0
BS2475M20 x P1.0
BS2476M22 x P1.0
BS2477M22 x P1.5
BS2442M24 x P1.0
BS2478M24 x P1.5
BS2470M26 x P1.0
BS2479M26 x P1.5
x P1.0
BS2443M27
(Left hand thread)
BS2444M27 x P1.25
BS2472M28 x P1.0
BS2471M28 x P1.5
BS2473M30 x P1.5
BS2474M33 x P1.5
1
2
6
3
7
8
12
5
9
10
ENGINE SYSTEM TOOLS
11
4
13
14
2
MAGNETO FLYWHEEL PULLER
Thread puller designed for fixed-point type magneto flywheels
Chrome alloy steel ball p on sha to reduce fric on stress during disassembly
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
BS2483 M24 x P1.0
BS2461 M24 x P1.5
BS2462 M26 x P1.0
BS2484 M28 x P1.0
BS2464 M30 x P1.0
BS2485 M30 x P1.25
BS2465 M30 x P1.5
BS2486 M32 x P1.5
BS2467 M33 x P1.5
BS2487 M35 x P1.0
BS2468 M35 x P1.5
BS2488 M38 x P1.5
BS2489 M42 x P1.5
BS2494 M50 x P1.5
BS2463 M30 x P1.5
BS2469 M35 x P1.5
1
2
4
5
6
7
9
10
11
13
30
3
14
8
12
15
16
BS30009
ALTERNATOR COVER PULLER FOR DUCATI 11
Removes DUCATI 1199 alternator cover with qualified capacity
Allows you to do this without prying on it with a screw driver
A must have tool for anybody pu翿 ng a lightweight flywheel in
their bike if you fry your alternator wires or if you plan on removing the cover for a general inspec on
Recommend to operate with 14mm hex driver with 27mm wrench
Relevant to DUCATI tool part number 88713.3922
ENGINE SYSTEM TOOLS
31
BS4532
BELT TENSION GAUGE
Compact design with graduated scale for easy reference
Designed to work with all belt drive models
Correct tension is cri cal, easily and accurately tests belt tension
with this gauge
FLYWHEEL PULLER KIT
An ideal tool set helps to remove clutch bodies, flywheel and
primary gears
CLUTCH AND TRANSMISSION TOOLS
BS3913
33
BS9950
FLYWHEEL PULLER KIT
Specially designed for standard AC flywheel wheel ring
6 sizes to fit most magneto flywheel threads
Taper lock flywheel could only be disengaged using this specialist
tool
Use with so face hammer for quick removal from tapered sha s
M14 x 1.5R RH External Thread
M16 x 1.5R RH External Thread
M18 x 1.5R RH External Thread
M27 x 1.0R RH External Thread
M24 x 1.0R RH External Thread
M10 x 1.25R RH External Thread
4
BS6728
HEAVY DUTY PULLEY HOLDER WRENCH (25~160m
Drop forged handle with heavy duty leather strap
The milled foot of the lever grips on the strap
The strap ghtens around the pulley as more effort is applied
Capacity: 25mm~160mm
1
2
3
4
1
BS9861 34 mm
2
BS9862 39 mm
3
BS9863 41 mm
4
BS9864 46 mm
CLUTCH NUT WRENCH
For removing and replacing the clutch nut on motorcycle
6 point
DUAL END BI-HEX PULLEY NUT WRENCH
(14 & 17mm)
T type dual head pulley wrench is clamped to the pulley and
prevents pulley rota on while torquing the pulley nut
Dual head for quick interchange
So grip handle
Use with pulley wrench or clutch holder
Size: 14mm and 17mm bi-hex
12 Point
CLUTCH AND TRANSMISSION TOOLS
BS9853
35
BS9854
FLAT TYPE CLUTCH OUTER HOLDING WRENCH
For clutch holding to inner gear work, using this tool to prevent clutch
rota on while torquing the inner gears or nuts
Applica on : HONDA Monkey, CUB
BS9855
CLUTCH OUTER HOLDING WRENCH
Holds clutch for inner gear work,
Use this tool to prevent clutch rota on while torquing the inner
gears or nuts.
Applica on : HONDA CD90, CR80, CRM50, 80, NSS50F,NSR50, 80,
NS-1, MBX50, TZR50R, XL50, 80, XR100
36
BS9859
PULLEY & CLUTCH LOCKING NUT WRENCH (45m
For removing and replacing the clutch lock nut on motorcycles.
Applica on : PIAGGO, GILERA, PEUGEOT, MRK, YAMAHA roller.
BS9856
PULLEY & CLUTCH 12-POINT LOCKING WRENCH (32mm)
The pulley locking tool is clamped to the pulley and prevents pulley rota on
while torquing the pulley nut.
Comfortable grip handle makes holding the job easier.
32mm, 12-point
Applica on : SUZUKI SCOOTER: Sepia, ZZ, address V125 magic address100
Not applicable : SUZUKI address V100
BS9857
PULLEY & CLUTCH 6-POINT LOCKING WRENCH (29mm)
BS9858
CLUTCH AND TRANSMISSION TOOLS
The pulley locking tool is clamped to the pulley and prevents pulley rota on while torquing the pulley nut.
Comfortable grip handle makes holding the job easier
29mm, 6-point
Applica on : YAMAHA 50cc, 125, AXIS 90, 100, BWS100
PULLEY & CLUTCH 3-POINT LOCKING WRENCH
(26mm)
The pulley locking tool is clamped to the pulley and prevents
pulley rota on while torquing the pulley nut.
Comfortable grip handle makes holding the job easier
26mm, 3-point
Applica on : MRK, YAMAHA
37
1
1
2
2
3
3
4
COUNTER BALANCER & CLUTCH HUB SPANNER
Made of heat-treated steel for balancer clutch hub and special
engine mount nut removal
1
BS3004 ID:Φ12.5mm x 6-Point
2
BS3002 ID:Φ17.5mm x 4-Point
3
BS3001 ID:Φ20.5mm x 4-Point
4
BS3003 ID:Φ24mm x 4-Point
1
2
3
NTER BALANCER & CLUTCH HUB SPANNER
Made of heat-treated steel for balancer clutch hub and special
engine mount nut removal
38
1
BS3009 ID:Φ29mm x 6-Point
2
BS3000 ID:Φ20.5mm and Φ24.5mm x 4-Point
3
BS3008 ID:Φ26.5mm and Φ30mm x 4-Point
Adjustable locking apparatus
Various pins
BS3112
CLUTCH AND TRANSMISSION TOOLS
5 pair pin set for interchange
UNIVERSAL PULLEY HOLDER WRENCH SET
Locking wrench type pulley holder holds clutch hubs, flywheels,
gears, pulley and sprockets
Durable handle and adjustable locking design
5 pairs of different size pins to suit many applica ons
Jaw capacity 140mm
Pin working capacity 22mm~145mm
39
BS30010
CRANK SHAFT TURNING TOOL FOR DUCATI 1199
Rotates DUCATI 1199 engine with crank sha safely
It allows you to safetly rotate the engine while checking the valve
clearances and igni on advance check or se翿 ng the ming
Recommend to operate with 17mm hex driver
Chrome molybdenum alloy steel, effec vely increase the service
life
Fits DUCATI 1199
Relevant to DUCATI tool part number 88713.3824
BS30008
CRANKSHAFT IN TDC POSITION TIMING TOOL FOR
DUCATI
This is a DUCATI engine cranksha locking in TDC posi on ming
tool
Recommend to operate with 6mm hex key and 17mm hex driver
Chrome molybdenum alloy steel, effec vely increase the service
life
Fits all DUCATI’s from 1990-2011
Relevant to DUCATI tool part number 88713.2011
40
BS30011
4PC BELT ROLLER TIMING ALIGNMENT TOOL (M5)
Thread size M5xP0.8
Belt roller ming of two-valve head
Relevant to DUCATI tool part number 88713.2009
BS30012
2PC BELT ROLLER TIMING ALIGNMENT TOOL (M6)
Thread size M6xP1.0
Applica on 3 valve engine alignment belt roller ming
Relevant to DUCATI tool part number 88713.2257
2PC BELT ROLLER TIMING ALIGNMENT TOOL (M8)
Thread size M8xP1.25
Applica on: HYPERMOTARD 1100 (08-12), 796 (10-12)
MONSTER 696 (08-10), 796 (11-14), 1100 (09-13), S2R 1000
(06-08)
MULTISTRADA 1000 (03-06), 1100 (07-09)
SPORTCLASSIC (06-10)
SUPERSPORT (03-06)
twin valve engine applica ons
Relevant to DUCATI tool part number 88713.2282
CLUTCH AND TRANSMISSION TOOLS
BS30013
41
BS4030
BS4031
OCTAGONAL FRONT FORK CAP TOOLOCTAGONAL
(45mm)
FRONT FORK CAP TOOL
Removes octagonal front fork caps
(46mm, FOR SHOWA)
Use with 3/8” Sq. Dr. or 19mm spanner
For SHOWA BPF 43mm front fork tubes, it fits 45mm
octagonal fork cap
BS4032
Removes octagonal front fork caps
Use with 3/8” Sq. Dr. or 19mm spanner
For SHOWA 44 thru 46mm front fork tubes, it fits
46mm octagonal fork cap
For removing the fork caps on late HONDA CRF’s. &
SUZUKI RM’s
Replaces SUZUKI OEM 09941-53620
Applica on: HONDA CRF 250R (2010) SUZUKI RM125 /
250.
BS4033
OCTAGONAL FRONT FORK CAP TOOLOCTAGONAL FRONT FORK CAP TOOL
(49mm)
(50mm, FOR SHOWA)
Removes octagonal front fork caps
Use with 3/8” Sq. Dr. or 19mm spanner
For KYB front fork cap
Applica on: HONDA CRF 450R, YAMAHA YZ125/250,
YZ250F/450F, Kawasaki KX450F
Removes octagonal front fork caps
Use with 3/8” Sq. Dr. or 19mm spanner
For SHOWA front fork cap
Replaces SUZUKI OEM 09941-53630
Applica on: HONDA CRF 250R/450R, CRF 250X/450X,
SUZUKI RM125/250, RMZ 250/450, Kawasaki KL250F
DUCATI STEERING STEM NUT TOOL
Ensures correct torque is achieved to the steering head compression nut
Compa ble with 3/8” Sq. Dr. torque wrench
Suits DUCATI motorcycles 1992 on including all 4V Superbikes,
Mul strada, Hypermotard and other models with the large diameter steering stem nut
Used with 3/8” Sq. Dr. and the rubber cushion design eliminates
damage to the steering stem nut in the removal and installa on
process
Replaces DUCATI tool P/No. 888713.1058
STEERING AND SUSPENSION TOOLS
BS4019
43
BS4051
KYB TWIN CHAMBER FORK COMPRESSION TOOL (36mm)
Removes the compression body from the cartridge on KYB twin
chamber forks
Use with 3/8” Sq. Dr. or 19mm spanner
For YAMAHA YZ series Replaces YAMAHA OEM YM-01500
BS4052
KYB TWIN CHAMBER FORK COMPRESSION TOOL (32mm)
Removes the compression body from the cartridge on KYB twin
chamber forks
Use with 3/8” Sq. Dr. or 19mm spanner
For KYB twin chamber forks and HONDA CRF 250 & 450
BS41500
FORK OIL LEVEL GAUGE TOOL
Simple and effec ve tool for checking and adjus ng the oil level
on conven onal and single chamber cartridge forks
Graduated steel tube with adjustable level se翿 ng ring measures
oil level from 0-300mm in 5mm increments
Can also be used on bicycles equipped with front suspension
Syringe capacity: 60ml
44
BS4201
STEERING BEARING OUTER RACE REMOVER TOOL
Easy outer race removal avoiding tube damage
4 contact points ensure even race removal
Suits tube dia Φ39mm ~ Φ57mm (1-1/2 ~ 2 3/16”)
Length: 320mm (12-1/2”)
Remove plas c protec on ears prior to use
1
3
1
BS4012 35mm Hex
2
BS4013 36mm Hex
3
BS4014 39mm Hex
TOP FRONT FORK HEX NUT WRENCH
STEERING AND SUSPENSION TOOLS
2
Helps to remove or install top fork nut on glide forks
3/8” square drive, allows for torque wrench or ratchet torque
ghtening
Suitable for Harley Davidson Sportsters and Big Twins
6 point
45
BS4400
STEERING STEM & FRONT FORK CAP ADJUSTING
WRENCH (30mm X 32mm)
Dual size wrench for compression fork cap stack adjustment or
removal
Installable for 21mm wrenches or 3/8” sq.Dr. digital reading driver
With addi onal nut driver
Size: 30mm x 32mm with 12-point.
FRONT FORK CAP ADJUSTING WRENCH WITH
ADDITION DRIVER
Wrench for compression fork cap and steering stem adjustment or
removal
Flat shape head is specific to confined areas during motorcycle
service
With addi onal nut driver
46
BS4401
BS4402
BS4403
BS4404
BS4405
BS4406
17mm x 24mm
17mm x 27mm
19mm x 24mm
19mm x 27mm
22mm x 27mm
22mm x 32mm
FRONT FORK DUST SEAL DRIVER
BS9827A (32mm)
BS9827H (40mm)
BS9827Q (27mm)
BS9827B (33mm)
BS9827J (41mm)
BS9827R (30mm)
BS9827C (35mm)
BS9827K (43mm)
BS9827S (31mm)
BS9827D (36mm)
BS9827L (45mm)
BS9827T (34mm)
BS9827E (37mm)
BS9827M (46mm)
BS9827U (42mm)
BS9827F (38mm)
BS9827N (48mm)
BS9827V (47mm)
BS9827G (39mm)
BS9827P (50mm)
BS9827W (49mm)
STEERING AND SUSPENSION TOOLS
Detachable hammer enables front fork oil seals with an inner tube
to be installed easily and accurately
Full range of driver sizes to suit most forks (21 sizes)
Heavy weight with extremely technical smooth surface inside provide proper forced opera on without damage concern
47
3
2
1
1
BS0350 19mm~51mm(3/4”~2”)dia
2
BS0351 32mm~76mm(1-1/4”~3”)dia
BS0352 51mm~120mm(2”~4-3/4”)dia
C HOOK WRENCH
3
Chrome vanadium hardened steel
Tempered C-hook wrenches are specially designed for using with slo ed retaining rings
4mm thin hook allows to access confined areas
in motorcycle steering and suspension
1
2
1
BS3101
46mm x50mm, 8-point box
BS3101
2
BS3102 49mm x50mm, 8-point box
STEERING STEM & FRONT FORK CAP WRENCH
8 point wrench for adjustment or removal of the fork cap (cartridge) on dual chamber
Closed cartridge forks
Can be used for removal of compression fork caps on motorcycles
48
BS9892
STEERING TUBE BEARING PULLER TOOL SET
Use this tool to remove the lower fork stem (separator) tapered
bearing
Tapered fork stem bearing remover features extra thin opening for
slot entry between stem and bearing
Rod extension can be used on mul ple sizes of fork stems
STEERING TUBE BEARING INSTALLER TOOL SET
The P.O.M. adaptor offers safe and appropriate bearing installaon
Simply choose the correct adaptor, slide the se翿 ng driver over
the steering tube and tap the bearing into place with a hammer,
avoiding any risk of damage
Adaptor sizes: 24, 26, 27, 28, 30mm
A
B
C
D
E
F
STEERING AND SUSPENSION TOOLS
BS9893
49
BS4100
HYDRAULIC COIL SPRING COMPRESSOR TOOL
Easy opera on oil pressure pump designed for suspension assembling and disassembling by compressing the coil spring
Special accessory features flat-top to easily interchange to bearing, component assembly
Opera on height: 350mm, width: 20mm~80mm
Pump stroke range: 135mm, withstand 4ton pressure
Easy-operated hydraulic gear
Adjust the gear according to the size of spring coil
BS5000
FRONT FORK & SHOCK VICE
Ideal assists holding round or awkward shaped items including
forks, shocks, pistons etc
Simply bolt vice onto your work area using the pre-drilled mounting holes
Unique V shape jaws are covered with thick rubber pads ensure
items are held in place without damage
Four posi on pin allows wide range opening maximum to 100mm
Made from hardened steel with anodised finish
BS5530
FRONT WHEEL SPINDLE REMOVE TOOL
50
Designed to fit most spindles during front wheel removal
4 sizes in 1 tool which covers sizes 17, 19, 22, 24mm (Hex 6 Point)
3/8” Sq.Dr., for maximum 90 /Ibs torque
BS9730
3PC HEX BIT SOCKETS (H8,H10,H12mm)
Bit sockets with different screw standard for various designs and
sizes of the front shock absorbers
Adjust shock absorbers according to different situa ons and
driving habits
Bit sockets allow a working angle up to 30° and provide improved access to hard-to-reach or hard angle areas
1/2” Sq.Dr
BS9731
3PC TX-STAR BIT SOCKET (T45,T50,T55)
BS9732
3PC SPLINE BIT SOCKET (M8,M10,M12)
Bit sockets with different screw standard for various designs
and sizes of the front shock absorbers
Adjust shock absorbers according to different situa ons and
driving habits
Bit sockets allow a working angle up to 30° and provide improved access to hard-to-reach or hard angle areas
1/2” Sq.Dr
STEERING AND SUSPENSION TOOLS
Bit sockets with different screw standard for various designs and
sizes of the front shock absorbers
Adjust shock absorbers according to different situa ons and driving habits
Bit sockets allow a working angle up to 30° and provide improved
access to hard-to-reach or hard angle areas
1/2” Sq.Dr
51
Patented
BS98940
STEERING HEAD BEARING INSTALLER TOOL SET
Vital tool to correctly install steering head bearings
A hassle free system reducing the possibility of damage
during the bearing installa on process
Heavy duty centre axle used with Polyoxymethylene (POM)
press rings ensure the bearing is installed straight and
smoothly in one mo on
No press, dri or impact tools required
Suits bearing diameter sizes: 41-55mm
Supplied with instruc on manual
Ideal accompanying product to:
BS4201 Steering Bearing Outer Race Remover
BS9892 Steering Tube Bearing Puller
Item
52
A
Part No.
BS98940A02
B
BS98940P13
C
BS98940P14
D
BS98940P15
E
BS98940P16
F
BS98940P17
G
BS98940P18
H
BS98940P19
I
BS98940P20
J
BS98940P21
K
L
M
N
BS98940P06
BS98940A01
BS98940P01
S0008204
Descripion
Press cap
ø41mm POM press ring
HONDA
ø43mm POM press ring
SUZUKI, YAMAHA
ø47mm POM press ring
Kawasaki, SUZUKI, YAMAHA
HONDA, TRIUMPH, MONTESA
ø48mm POM press ring
SUZUKI, YAMAHA, Kawasaki
ø48.6mm POM press ring
HONDA
ø50mm POM press ring
HONDA, KTM, HUSABERG
BUELL, HUSQVAMA, VICTORY
HARLEY
ø51mm POM press ring
HONDA,TM
ø52mm POM press ring
Kawasaki, SUZUKI, YAMAHA
HONDA, TRIUMPH
ø55mm POM press ring
Kawasaki, SUZUKI, YAMAHA
HONDA, TRIUMPH, TM
APRILIA, DUCATI, MOTO GUZZI
Press plate
Central axle
T bar
BS50006
FORK CAP SOCKET FOR OHLINS 50mm FORK
Recommend to operate with 1/2” SQ. and 24mm hex driver
Fork cap wrench suits 50mm Ohlins forks
Measure the top of your forks 50mm or just under 2”
Relevant to DUCATI tool part number 88713.2854
BS50007
BS50008
FORK CAP SOCKET FOR MARZOCCHI FORK
FORK
Recommend to operate with 1/2” SQ. and 24mm hex
driver
Fork cap wrench suits all DUCATI Hypermotard “S”
with marzocchi forks
An ideal way to remove the fork caps without damage
Relevant to DUCATI tool part number 88713.3091
Recommend to operate with 1/2” SQ. and 24mm hex driver
Applica on: 899, 1199 and 1299
Relevant to DUCATI tool part number 88713.4337
BS50009
FORK CAP SOCKET FOR SACHS FORK
STEERING AND SUSPENSION TOOLS
FORK CAP SOCKET FOR OHLINS MECHATRONICS
Recommend to operate with 1/2” SQ. and 24mm hex driver
Applica on: MTS1200, MY13
Relevant to DUCATI tool part number 88713.4303
53
BS5582
VACUUM PUMP & BRAKE BLEEDER KIT
Designed to locate and iden fy faults on motorcycles
Applica ons include fuel, diagnos cs, transmission, emissions and
clutch bleeding
Supplied complete with three connector sizes and various adaptors
Die cast body with gauge and accessory kit
Easily dismantled for cleaning
Supplied in metal case
Contents:
2PC Suc on cup
3PC Bleed nipple adaptor
2PC Gun Fi翿 ngs and Tube adaptor
8PC Hose Fi翿 ngs
BRAKE SYSTEM TOOLS
55
BS5800
BRAKE PISTON DETACHING TOOL
Detaches the piston from the disc caliper
Ratche ng handle allows convenient opera on in compressing the
brake piston
Capacity: 20-54mm
BS9870
DISC PAD BRAKE SPREADER (30mm)
BS9871
DISC PAD BRAKE SPREADER (65mm)
Compresses the brake pistons on most style calipers for easy pad
replacement
Suits all front and some rear motorcycle disc brakes
56
BS5630
BRAKE FLUID TESTER
Quick and accurate tester ensures brake fluid to be in serviceable
condi on
Green LED: Moisture less than 1.5% (Properly)
Yellow LED: Moisture between 1.5% and 3.0% (Marginal)
Red LED: Moisture greater than 3.0% (Failed)
BRAKE SYSTEM TOOLS
BS0245
BRAKE FLUID CONDITION TESTER
Twist down the test probe bar to clean the two electrodes on
the test bar head
Immerse the test bar head into new brake fluid approximately
20mm
Press the test bu on
Use a Phillips screwdriver to adjust the reset screw
Turn un l the green reset indicator (far le ) flashes
57
BS35101
UNIVERSAL CHAIN REPAIRING MASTER SET
Comprehensive tool kit for drive chain replacement and repair
Provides the ability to break, rivet and press drive chain master links
Forged hardened alloy steel body with 3 posi on handle suitable for
le and right handed use
Supplied with press plates, punches and anvils
Features knock spindle, a ming saving tool to fla en and shape pins
Suitable for chain sizes: #415, #420, #428, #520, #525, #530 (#50),
#532, #630 and #632
Instruc on manual included
PROFESSIONAL CHAIN REPAIRING MASTER SET
WHEEL AND CHAIN TOOLS
BS3510
Breaks presses and rivets chain
Forged harden alloy steel body with 3 posi on handle, suitable
for le and right hand use
Supplied with press plates, punches and anvil
Suitable for chain sizes: #415, #420, #428, #520, #525, #530
(#50), #532, #630 and #632
Rivets hollow pin master links
Professional heavy duty
Instruc on manual included
59
BS70002
MOTORCYCLE CHAIN MAINTENANCE SET
Including complete universal chain repairing master set designed
to break chains up to chain size #632 and press the hollow link
pins and plates of the master link on chains up to #632, and light
tools, mul ple choices fulfill the easy opera on of chain repairing
work
Set includes : BS1164, BS3500, BS3506 and BS35101
BS3500
CHAIN EXTRACTOR
Spring loaded clamp
Designed for one-hand chain repair and quick pin release
Applica on size: #4 chain
Grind chain pin heads prior to use
60
BS1164
DRIVE CHAIN TENSION PULLER
Fit tool jaws in chain link ends, ghtening of the forcing screw
pulls the jaws together to tension the chain for easy removal or
installa on of the chain connector or master link
Designed for drive chains found on motorcycles and all-terrain
vehicles (ATVs)
Holds chain together in posi on to leave hands free
Length: 130mm
WHEEL AND CHAIN TOOLS
BS3506
CHAIN LINK PLIERS
Designed to simplify installa on and removal of clip-type
master chain links
Place the shorter notched p on the pin, to push the clip in
and out with the longer p easily
61
BS32100
2” FUNCTIONAL TYRE INFLATOR DIAL GAUGE
550mm rubber hose makes easy access for all kinds of motorcycle
Die cast valve body with corrosion resistant brass valve
2 scale on 2” Dia. dial gauge, easy to read from 0 to 160 PSI or 0 to
11bar
BS0353
CHAIN ADJUSTING C HOOK WRENCH
Chrome vanadium hardened steel
Tempered C-hook wrench is specially designed for use with slo ed
retaining rings, such as motorcycle monoshock suspension and
rear wheel hub’s eccentric axle for chain elas city
Thin and adjustable hook enables access in confined areas (4mm
thickness)
Size range: 118.3-158.8mm (4 1/2”-6 1/4”)
BS5510
MULTI-FUNCTION TYRE VALVE TOOL
62
4 in 1 func on:
1. Valve installer and remover
2. Pressure release
3. Valve core installer
4. Valve thread chaser
BS55301
DUCATI FRONT AXLE ALIGNMENT TOOL (SHOWA 25mm)
BS55302
DUCATI FRONT AXLE ALIGNMENT TOOL (OHLINS 25mm)
DUCATI FRONT AXLE ALIGNMENT TOOL (OHLINS 30mm)
Essen al tool for aligning the front axle on DUCATI motorcycles with
Showa and Ohlins suspension
Alignment of the front axle is cri cal to allow access to the compression
damping screw for suspension adjustment
T-bar handle provides an easy and secure grip when correctly aligning
the axle with the notch on the fork bo om during axle ghtening
Part No.
Suspension Type Axle Inside Dia. mm
BS55301
Showa
25
BS55302
Ohlins
25
BS55303
WHEEL AND CHAIN TOOLS
BS55303
Ohlins
30
748, 749, 916, 996, 998, 999, ST2,
ST3, ST4, 800SS and 1000SS
Hypermotard 796 and 1100
Panigale 848, 1198 and 1199,
and Diavel
63
BS5531
FRONT WHEEL SPINDLE REMOVAL TOOL (14mm HEX )
14mm internal axle nut hex socket helps to remove front wheels
1/2” Sq. Dr
Maximum torque 150 lbs
For KYB twin chamber forks and HONDA CRF 250 & 450
BS5532
FRONT WHEEL SPINDLE REMOVAL TOOL (19mm HEX )
19mm internal axle nut hex socket helps to remove front wheels
1/2” Sq. Dr
Maximum torque 150 lbs
For YAMAHA YZ series Replaces YAMAHA OEM YM-01500
B
C
D
A
E
F
G
H
K
L
BS5535
M
WHEEL BEARING REMOVAL TOOL SET
Split collet tool set for radial ball bearing removal.
Sliding hammer and adaptors to suit ball bearing inner diameter
sizes from 15mm to 30mm.
Collet sizes: 15mm, 17mm, 20mm, 25mm, 28mm and 30mm.
Hand grip protector prevents hand injuries when opera on
64
A
B
C
D
E
F
Tap rod
Slide hammer
15mm split collet
17mm split collet
20mm split collet
25mm split collet
G
H
K
L
M
28mm split collet
30mm split collet
Tap head
Stepped alignment bush
Hand grip protector
BS5551
BS5550
DUCATI REAR WHEEL NUT SOCKET (41/46mm)
DUCATI WHEEL NUT SOCKET (30/55mm)
Designed maximum torque 280-320Nm to prevent
locknuts and wheel spindle threads damage due to over
ghtening
Designed to break if over ghtened elimina ng damage
to expensive locknuts, spindles or swing arms
Dual-end socket in size:
41mm and 46mm hex
Applica on: DUCATI 748, 916, 996, 998
Superbike 848, Hypermotard 798, 1100, Monster 796,
1100, and fit more 41mm hex and 46mm hex rear wheel
nut
1/2” Sq. Dr.
Designed maximum torque 280-320Nm to prevent locknuts
and wheel spindle threads damage due to over ghtening
Designed to break if over ghtened elimina ng damage to
expensive locknuts, spindles or swing arms
Two-step socket 30mm hex for front lock nut, 55mm Bi-hex
for rear lock
nut
Applica on: DUCATI Superbike 1098, 1198, Mul strada
1200, Stree ighter
and Diavel
1/2” Sq. Dr.
BS5553
BS5552
MV AGUSTA WHEEL NUT SOCKET (26/56mm) DUCATI FRONT WHEEL NUT SOCKET ( 28/30mm)
Designed maximum torque 280-320Nm to prevent locknuts
and wheel spindle threads damage due to over ghtening
Designed to break if over ghtened elimina ng damage to
expensive locknuts, spindles or swing arms
28mm and 30mm hex.
Applica on: DUCATI 748, 916, 996, 998.
Superbike 848, Hypermotard 798, 1100, Monster 696, 796,
1100, and any DUCATI
with a 25mm front axle
1/2” Sq. Dr.
BS03531
BENELLI REAR WHEEL AXLE AND CHAIN ADJUSTING
WHEEL AND CHAIN TOOLS
Designed maximum torque 280-320Nm to prevent
locknuts and wheel spindle threads damage due to over
ghtening
Designed to break if over ghtened elimina ng damage
to expensive locknuts, spindles or swing arms
Two-step socket 26mm Bi-hex for front lock nut, 56mm
Bi-hex for rear lock nut.
Applica on: MV Agusta F4 all model and Brutale all
model
1/2” Sq. Dr.
TOOL
Designed for Benelli motorcycle rear wheel axle
Plas c steel p design and aluminum tool body prevent injury to
motorcycle
Applica on: Benelli TER 1130 K, TNT 899 / TNT 1130 Sport EVO,
Tornado Naked TRE 899 / 1130 / 1130 R, TRE 1130 K Amazoan,
and more Benelli motorcycle
Used 19mm hex driver to adjust the chain tension and se翿 ng
rear wheel
65
BS9952
3PC RIM PROTECTOR SET
Protects wheel rims from damage during tyre removal
Overall length: 150mm
BS9953
TYRE LEVER (280mm)
Drop forged and tempered alloy steel designed for motorcycle
tyre removal
Includes easy holding rubber handle
Length: 280mm (11”)
Width: 25mm (1”)
66
BS5612
CURVE TYPE TYRE LEVER
Drop forged and tempered alloy steel
Designed for motorcycle tyre removal
Length: 350mm
WHEEL AND CHAIN TOOLS
BS5603
TYRE LEVER (200mm)
Drop forged and tempered alloy steel designed for motorcycle
tyre removal
Length: 200mm (8”)
BS5604
TYRE LEVER (400mm)
Drop forged and tempered alloy steel designed for motorcycle
tyre removal
Length: 400mm (15-3/4”)
67
BS3701
TYRE BEAD HOLDING TOOL
Used to push the tyre bead down into the drop center of the rim
on supermoto wheels while using tyre tools to change tyres
Hooks over spoke and pushes bead down on opposite side of tyre
from tyre levers
Simply hooks over your spoke and inside the rim to hold the tyre
down
Holds the bead down while installing tyres
BS8008
TYRE CHANGE EXTRUDER TOOL
Holds the tyre bead down when installing or repairing tyres
Size: 290x150x50mm
BS5610
TYRE BEAD HOLDING CLAMP
Designed to push and hold the bead down into the centre of the
rim during installa on and repair of off road tyres
Assists when using tyre levers to remove tyres
Plas c screw protects rim
68
BS3949
VALVE CORE TORQUE TOOL
Ensures accurate torquing of tyre valves and reduces leaking via
the valve
Torque limit: 45NCM / 4 IN. LB
DIGITAL TYRE PRESSURE GAUGE
Angled nozzle fits all types of motorcycle valves
Calibra on in Bar, kPa and PSI at the push of a bu on for unit
change
One hand opera on and accurate digital LCD reading
Low power consump on
Measuring range 2–100 PSI (0.15–7.00 Bar)
Resolu on 0.5 PSI (0.05 Bar or 5 kPa)
Accuracy +1% +0.5 PSI
Opera ng temperature 10°C–30°C/50°F–86°F
Power 3V Lithium ba ery
WHEEL AND CHAIN TOOLS
BS3238
69
Patented
BS3699
TYRE VALVE EXTRACTOR BAR
Steel bar with movable rubber sleeve offers maximum leverage
during removal of snap-in valves
Prevents damage to alloy wheels
BS3211
3 IN 1 FUNCTIONAL TYRE GAUGE
Func on includes checking and lowering tyre pressure and checking tyre depth
45° head for convenient valve access
Tyre pressure checking range: 0–50 PSI/ 0–350 Kpa
For tyre thread depth 0–10mm / 0–32 unit (1/32”)
70
WHEEL AND CHAIN TOOLS
BS5501
WHEEL TURNING & BALANCE STAND
Adjustable centring coned rods on ball bearings
Stand with adjustable legs and moulded all-round reading level to
ensure extremely accurate and reliable wheel balancing
Capacity 430mm (17”)
Radius width 370mm (14 1/2”)
Complete with dial gauge for accurately checking runout
71
BS5502
Aluminum
&
Steel
Aluminum Head
Prevent Overload Tightening
Steel Head
For Powerful
Tightening & Removing
BS5503
All
Steel
BS5502
Patented
22PC SPOKE TORQUE WRENCH SET 4FT/POUND
BS5503
Patented
22PC SPOKE TORQUE WRENCH SET 4FT/POUND
Dual-head spoke wrench enables ghtening and removing
spokes in one piece
Spoke torque tensioner applies correct and equal tension to
the spokes
Spoke remover releases damaged or rusted spokes easily
Features an o-ring seal in both ends for dustproofing
Simply ghten the spoke un l you hear and feel a click
which indicates correctly adjustment
Takes all the guesswork out of wheel and spoke assembly
and maintenance
Includes 11 x 2 interchangeable heads
Torqueendwrench:
5.0mm, 6.5mm, 5.6mm, 6.7mm, 6.0mm, 6.9mm, 6.2mm,
7.1mm, 6.3mm, 7.4mm, Spline
Fixedendwrench:
5.0mm, 6.5mm, 5.6mm, 6.7mm, 6.0mm, 6.9mm, 6.2mm,
7.1mm, 6.3mm, 7.4mm, Spline
72
1
4
1
BS4018Φ 36mm x 4-Point
2
BS4008Φ 40mm x 4-Pins
3
BS4009Φ 40mm x 4-Pins and 1 Notch
4
BS4010Φ 44mm x 6-Point
5
BS4011 Φ 47mm x 6-Point
5
WHEEL AND CHAIN TOOLS
3
2
SEAL AND BEARING RETAINER TOOL
For rear wheel bearing and seal retainer ring removing and replacing
Allows removal and replacement of the accessory fork cap
Precision design prevents damage to the retainer ring a er peined
stakes have been removed
73
MASTER MECHANICS TOOL KIT
All 114pc tools are made of Alloy Steel with high standard heat
and surface treatment “STRONG & ANTIRUST”
BUCKLE-UP AUTO-LOCK func on for all layers to avoid dropping
during carrying
Portable size (495mm L x 220mm W x240mm H) and weight
(14.3kgs) allows easily carried out
EVA base for protec ng tools from collision damage and easily
reposi oning
Most complete socket kit specially selected for motorcycle
repair job with no excess tools or sizes included
GENERAL SERVICE TOOLS
BS9839
75
MASTER MECHANICS
Quick-Release & Locking rachet wrench,
driver and extension bar provides Fast
Release, Strong Connec on and prevents
TOOL
KIT
socket or bit socket from dropping into
narrow space in motorcycle
6, 8, 10, 12, 14mm fully polish chrome
plated combina on wrenches with 45
degree angle in bi-hex box end provides
high performance in motorcycle maintainance work
Variety of colloca on provides most suitable
opera on for different situa on
BS9211L
BS9212L
BS9213L
6-points Flank Drive Socket can grip
more ghtly and prevent any damage during opera on
TPR & PP surface protects your
motorcycle from collision damage
during opera on
Extra-Thin wall design is specially for
motorcycle narrow working space
Magne zer/Demagne zer allows L-Key
to hold screws steadly while se翿 ng
BS9214L
BS9310L
BS9311L
BS9312L
BS9313L
BS9314L
BS9315L
BS9316L
BS9317L
BS9318L
BS9319L
BS9114
BS9112
BS9110
BS9108
BS9106
BS9205L
BS9206L
BS9207L
BS9208L
BS9209L
BS9314S
BS9210L
BS9313S
BS9315S
BS9204S
BS9205S
BS9206S
BS9432S
6mm
BS9207S
BS9208S
BS9209S
BS9210S
BS9211S
BS9212S
BS9316S
BS9213S
BS9312S
BS9317S
BS9214S
BS9311S
BS9310S
BS9318S
BS9410S
BS9411S
BS9319S
BS9412S
BS9309S
BS9320S
BS9413S
BS9414S
BS9321S
BS9415S
BS9430S
BS9427S
8mm
BS9424S
10mm
BS9422S
BS9421S
BS9419S
BS9418S
BS9417S
12mm
14mm
Sockets:
● 10pc 1/4”Dr. Deep Sockets (long) : 5 , 6 , 7 , 8 , 9 , 10 , 11 , 12 , 13, 14mm
● 11pc 1/4”Dr. Regular Sockets (short) : 4 , 5 , 6 , 7 , 8 , 9 , 10 , 11 , 12 , 13, 14mm
● 10pc 3/8”Dr. Deep Sockets (long) : 10 , 11 , 12 , 13 , 14 , 15 , 16 , 17 , 18 , 19mm
● 14pc 3/8”Dr. Regular Sockets (short) : 8 , 9 , 10 , 11 , 12 , 13 , 14 , 15 , 16 , 17 , 18 , 19 , 20 , 21mm
● 16pc 1/2”Dr. Regular Sockets (short) : 10 , 11 , 12 , 13 , 14 , 15 , 16 , 17 , 18 , 19 , 21 , 22 , 24 , 27 , 30 , 32mm
76
BS9308S
BS9416S
BS9119
BS9118
BS9130
BS9839G
BS9117
BS9129
BS9127
BS9115
BS9128
BS9132
BS9133
BS9134
BS9135
BS9116
BS9126
BS9131
BS9017
BS9006
BS9007
BS9008 BS9009
BS9010
BS9011
BS9012
BS9013
BS9014
BS9015
BS9016
BS9021
BS9022
BS9023
BS9018
BS9019
Extension Bars :
● 6pc Lock Type Extension Bars :
1/4”Dr. x 150mm (6”)
3/8”Dr. x 100mm (4”)
3/8”Dr. x 150mm (6”)
1/2”Dr. x 150mm (6”)
1/2”Dr. x 250mm (10”)
3/8”Dr. x 250mm (10”) With 1/2”Dr. Slide Handle
Bit Sockets :
●12pc 1/4”Dr. Bit Sockets :
Hex : 2.5 , 3 , 4 , 5 , 6mm
TX-Star : T10 , T15 , T20 , T25 , T27 , T30, PH3
Square Drive Adaptors :
● 5pc Square Drive Adaptors :
1/2”F Dr. x 3/8”M Dr.
3/8”F Dr. x 1/4”M Dr.
1/4” Dr. Universal Joint
3/8” Dr. Universal Joint
1/2” Dr. Universal Joint
Thin Wall Spark Plug Sockets :
●4pc Thin Wall Spark Plug Sockets :
14 , 16 , 18 , 20.8mm
BS9020
●6pc 3/8”Dr. Bit Sockets :
Hex : 7 , 8 , 10mm
TX-Star : T40 , T45 , T50
Allen Key Wrenches :
● 5pc Allen Key Wrenches :
1.5 , 2 , 2.5 , 3 , 4mm
BS9125
BS7289
BS9104
BS9122
BS9123
BS7288
BS9120
BS9124
BS9121
Ratchet Wrenches :
●3pc Bikeservice Ratchet Wrenches :
1/4”Dr.
3/8”Dr.
1/2”Dr.
GENERAL SERVICE TOOLS
BS7291
Screw Drivers :
●4pc Screw Drivers :
PH2 Stubby Type (90mm L)
Flat 6.5mm Stubby Type (90mm L)
PH2 (210mm L)
Flat 6.5mm(210mm L)
1/4”Dr. Lock Type Drive Handle
Miniature Magne zer
Square Drive Adaptors :
●1/4”Dr. x 1/4”Hex
77
BS1660
8PC T-HANDLE SOCKET WRENCH SET (300mm)
Drop forged chrome vanadium steel socket and sha with heat
treated and chrome plated finish
Carbon steel handle
Length: 300mm
Sizes include: 6mm, 8mm, 10mm, 12mm, 13mm, 14mm, 17mm
and 19mm
BS1601
T-HANDLE SOCKET WRENCH HOLDER
Made of steel with sandblas ng and baked pain ng processing
8 different holes allows each T-handles to be either standing or
sliding on shelf firmly
Convenient for T-handle storage and quickly opera on be placing
in flat or hanging on the wall
78
BS1660A
8PC T-HANDLE SOCKET WRENCH SPEED RING SET (300mm)
Drop forged chrome vanadium steel socket and sha with heat
treated and chrome plated finish
Carbon steel handle
Speed ring mounted T-handle provides faster and easier removal
and installa on of bolts and nuts
6 point
Sizes include: 6mm, 8mm, 10mm, 12mm, 13mm, 14mm, 17mm
and 19mm
GENERAL SERVICE TOOLS
Patented
BS1700
4PC T-HANDLE SPEED RING SET
Patented designed helps to remove clutch bodies, flywheel and
primary gears smoothly and e翿 ciently
79
Part No.
T-HANDLE HEX WRENCHES
For the removal and installa on of hex style screws, bolts and
fi翿 ngs
Hex key fi翿 ngs on each point of the tool (3 in total) for quick
and easy opera on
T-Handle design with 3-posi on sliding T-bar handle allowing
greater leverage
Manufactured from heat treated chrome vanadium steel
Sold individually
Part No.
Torx Size mm
Length mm
BSG01686-05
T25
180
BSG01686-06
T27
180
BSG01686-07
T30
180
BSG01686-08
T40
210
BSG01686-09
T45
210
BSG01686-10
T50
210
Hex Size mm Length mm
BSG01685-03
3
125
BSG01685-05
4
180
BSG01685-07
5
180
BSG01685-08
6
210
BSG01685-10
8
250
BSG01685-11
10
300
BSG01685-12
12
320
BSG01685-13
14
340
T-HANDLE TORX WRENCHES
For the removal and installa on of Torx style screws, bolts
and fi翿 ngs
Torx key fi翿 ngs on each point of the tool (3 in total) for quick
and easy opera on
T-Handle design with 3-posi on sliding T-bar handle allowing
greater leverage
Manufactured from heat treated chrome vanadium steel
Sold individually
80
BS80016
1/2”DR UNIVERSAL JOINT T-HANDLE WREN
BS80017
3/8”DR UNIVERSAL JOINT T-HANDLE WREN
BS80018
mm
1/4”DR UNIVERSAL JOINT T-HANDLE WREN
Part No.
Sq. Drive
Length mm
BSG1687-01
1/2”
500
BSG1687-02
3/8”
420
BSG1687-03
1/4”
375
Long reach T-handles with universal joint drive ideal for
accessing confined fasteners
Sliding beam handle can be set in three posi ons for
added leverage
Manufactured from chrome vanadium steel for strength
and durability
Available in 1/4, 3/8 and 1/2” square drive
1/4” SQUARE DRIVE RATCHET HANDLE
BS7289
GENERAL SERVICE TOOLS
BS7288
3/8” SQUARE DRIVE RATCHET HANDLE
BS7291
1/2” SQUARE DRIVE RATCHET HANDLE
Offset designed with quick release and reversible
72 teeth ratchet covered with heavy duty coa ng
Strong and durable handle provides heat insula on features
Designed for specific motorcycle work without damage bike
surfaces
81
BS5420
1/2” DRIVE TELESCOPIC RATCHET
Heavy duty 36 tooth ratchet with robust outer casing
Telescopic handle extends to increase overall length by 150mm
providing addi onal leverage
Ideal for axle nuts or where addi onal leverage is required
Manufactured from chrome vanadium steel for strength and
durability
Overall length: 340mm, extended: 490mm
BS5421
1/4” SQ. DR. DIGITAL READING TORQUE WRENCH
(10-50Nm)
BS5422
3/8” SQ. DR. DIGITAL READING TORQUE WRENCH
(20-100Nm)
BS5423
1/2” SQ. DR. DIGITAL READING TORQUE WRENCH
(40-200Nm)
82
Available in 1/4”, 3/8”, 1/2” Sq. Dr.
72 teeth ratchet
LCD displays in Nm, .Lbs, in.Lbs, kgm, kg-cm
Click sounds as torque achieved
Ba ery operated use CR 2032 (3volt)
Oil resistant impact resistant casing
Automa c power off a er 2 minutes
Calibra on cer ficate supplied
BS9404
MAGNETIC STORAGE TRAYS (240X140mm)
Useful storage trays with strong in-built magnet
Ideal for storing and holding small parts, nuts, bolts and screws
neatly and securely during dismantle and reassembly
Strong magnets a ach to all metal surfaces including hoists, scissor
li s and steel workbenches, even upside down
Great me saver, handy on the spot storage op on
MAGNETIC STORAGE TRAYS (4”, ROUND)
Useful storage trays with strong in-built magnet
Ideal for storing and holding small parts, nuts, bolts and screws
neatly and securely during dismantle and reassembly
Strong magnets a ach to all metal surfaces including hoists, scissor
li s and steel workbenches, even upside down
GENERAL SERVICE TOOLS
BS9434
83
BS9101
9PC TX-STAR EXTRA-LONG SHAFT KEY SET
9 piece key sets featuring extra-long angled key sha s
Supplied with magne ser to assist in the fitment and removal of
fasteners
Ball end allows improved access to applica on and up to 25° working angle for increased speed and ease of entry (Hex set only)
Made from chrome-vanadium steel with polished chrome plated
finish
Supplied in a hinged storage holder with magne ser a ached
Available in Hex and TX-Star/Torx sets
Tx-star sizes: T10, T15, T20, T25, T27, T30, T40, T45, T50
BS9103
9PC HEX EXTRA-LONG SHAFT KEY SET
9 piece key sets featuring extra-long angled key sha s
Supplied with magne ser to assist in the fitment and removal of
fasteners
Ball end allows improved access to applica on and up to 25° working angle for increased speed and ease of entry (Hex set only)
Made from chrome-vanadium steel with polished chrome plated
finish
Supplied in a hinged storage holder with magne ser a ached
Available in Hex and TX-Star/Torx sets
Hex sizes: 1.5, 2, 2.5, 3, 4, 5, 6, 8, 10mm
84
BS6300
9PC MAGNETIC TX-STAR KEY SET
Fully polished chrome plated
TX-Star sizes: T10, T15, T20, T25, T27, T30, T40, T45 and T50
Chrome-vanadium steel made with build-in strong magnet to prevent screws dropping into frame slot when working
Another end of the key is tamper proof func on
GENERAL SERVICE TOOLS
BS9102
9PC MAGNETIC BALL POINT HEX KEY SET
Fully Polished chrome plated
Hex sizes: 1.5, 2, 2.5, 3, 4, 5, 6, 8 and 10mm
Ball end allows for be er access to allen-head bolts up to 25-degree working angle.
Chrome-vanadium steel made with build-in strong magnet to hold
screws in posi on
85
BS2260
REINFORCED PLASTIC SUPER SCRAPER (15mm)
BS2261
REINFORCED PLASTIC SUPER SCRAPER (30mm)
BS2262
REINFORCED PLASTIC SUPER SCRAPER (50mm)
Mul -func on designed for general scraping jobs
Ideal for removing badges, gaskets, stripes, decals etc.
Eliminates damage to the surface of so metals and paintwork
Durable tough handle suitable for hammer use where extra force
is required.
Length: 280mm (11”)
BS6050
HANDY PANEL REMOVAL TOOL
Specially designed extra slim profile and unique shape for the
delicate task of removing small or fine fascia trim and bezels, etc
Impact resistant high quality nylon prevents scratching to metal
and paint surfaces
Great for removing fairings
86
BS6502
PRESSURE ADJUSTING POWER CLAMP
Help easily to firmly fix the component
Plas c clamp avoids damage to aluminium alloys, plas cs and
lacquered components in the repair process
Working range: 0~53mm (2”)
GENERAL SERVICE TOOLS
BS9621
4PC STUBBY SCREWDRIVER SET
Stubby size allows access in confined spaces
Ideal for motorcycle fairings and cooling hoses
Manufactured from alloy steel with easy grip handle
Contains 2 x Slo ed (5 & 6mm) and Phillips (PH1, PH2)
head styles
87
BS9651
IMPACT DRIVER SET
Loosens rusted or seized nuts and bolts
Reversible for secure ghtening and removal
4 Phillips bits: PH1, PH2, PH3, PH4
3 Flat bits: 8mm, 10mm, 12mm
BS6012
8PC MULTI DRIVER WRENCH SET
88
Fits Metric and SAE 6pt, 12pt, TX-Star, Square, 30% rounded off,
Spline and RIBE nut
6mm: BS6012A
8mm: BS6012B
10mm: BS6012C
12mm: BS6012D
13mm: BS6012E
14mm: BS6012F
17mm: BS6012G
19mm: BS6012H
BS7352
8PC RATCHET WRENCH SET METRIC - STUBBY FLEX HEAD
Flexible head (180°) stubby combina on ring/open end design
Features 72 (5°) tooth ratchet head assembly
Manufactured from tempered forged alloy steel with polished mirror chrome finish
Ideal for confined spaces where working room is limited
Size contents: 6, 8, 10, 12, 13, 14, 17, 19 (mm)
RATCHET WRENCH
GENERAL SERVICE TOOLS
BS7407
Fully polished chrome plated
Patented ratche ring end combina on wrenches
6mm: BS7407H
8mm: BS7407A
10mm: BS7407B
12mm: BS7407C
13mm: BS7407D
14mm: BS7407E
17mm: BS7407F
19mm: BS7407G
89
BS1034
WIRE FINGER TOOL
The stainless steel rope is 450mm in length which allows cables
and lines to be pulled through confined spaces
Firmly holds wires and fasteners during removal and replacement
Net diameter: 20mm
BS7030
FLEXIBLE MAGNETIC CLAW PICK UP TOOL (700mm)
The flexible spring sha allows the tool to reach awkward areas to
grab parts
Press the bu on to extend claw
Magnet loads weight up to 1LB
Length: 700mm
Claw maximum opening: 25mm
90
BS9470
SAFETY WIRE TWIST PLIERS
A versa le tool helps to do reliable safety-wiring rapidly and consistently
Features automa cally spring return and right-hand twist
Made of forged alloy steel
Tapered jaws for easy access to confined areas
Mated cu翿 ng edges to cut safety wire and a long life mechanism
for excellent performance on machinery, motorcycle, vehicles and
aircra
GENERAL SERVICE TOOLS
BSG02840
6” SAFETY WIRE TWISTING PLIER WITH
RESERSIBLE
The more compact short model will lock fasteners beyond the
reach of the standard model
Side cu er stainless and inconel wire dia. 1mm
Slim nose p for op mum manoeuvrability
Securing assemblies sugjected to vibra on
Fast twist wire links
91
BS0044
BS5201
BS0044
HEADLIGHT & BRAKE SPRING HOOK
Made of heat treated alloy steel, specially designed for removing
and installing hard-to-reach headlight adjus ng springs and brake
springs
Length: 150mm (6”), with a 75mm (3”) wide T-handle
BS5201
U HOOK HANDLE (195mm)
Used to remove exhaust pipe springs, seat or tank holding springs
co er pins, side stand springs and other part
BS9835
BS9836
BS9838
BS9835
ACCELERATOR AND CLUTCH CABLE WIRE
REPLACEMENT TOOL
BS9836
M5 BRAKE CABLE WIRE REPLACE TOOL
r
Old brake cable wie
BS9838
M6 BRAKE CABLE WIRE REPLACE TOOL
Replace Tool
92
New brake cable wire
Bullet shape tool connects one end of old cable wire and one end of new
cable enabling ease of cable replacement without damage
BSG09835: Accelerator and Clutch Cable Wire Replace Tool
BSG09836: M5 Brake Cable Wire Replace Tool
BSG09838: M6 Brake Cable Wire Replace Tool
BS1234
4PC HANDY PICK & HOOK SET (76mm)
Designed for easy removal of o-rings, split pins, seals and bushes
in various mechanical applica ons
Made of stainless steel with durable plas c so grip handle
Contains straight awl, hook tool, 45° and 90° bent picks
Sha length: 76mm (3”)
Overall length: 162mm (6 3/8”)
Hook pick
90O angle pick
45O combination pick
Straight pick / Awl
BS0230
Four angles op ons and extra long sha s help to reach o-rings or
seals in deep areas
Made of stainless steel with durable plas c so grip handle
Contains straight awl, hook tool, 45° and 90° bent picks
Sha length: 152mm ( 6” )
Overall length: 241mm (9 1/2”)
GENERAL SERVICE TOOLS
4PC LONG PICK & HOOK SET (152mm)
BS1235
2PC SEAL PICK SET
Quick and easy removal of O-Ring and grease oil seals
Special angle designed head provides an easiy access for
removal
Length: 170mm and 150mm
93
BSG09041
BSG09037
BSG09036
BS9036
HOSE CLAMP PLIERS (3~12mm)
BS9037
HOSE CLAMP PLIERS (3.5~18mm)
BS9041
HOSE CLAMP PLIERS (4~28mm)
Crimps hose during repairs and maintenance
Radius jaws prevent damage to hoses
Lock ring holds hose in sealed posi on
BS9035
2PC RUBBER LINE CLAMP SET
Clamps hoses without damage
Suits fuel, vacuum and brake lines
Jaw capacity maximum 20mm
94
BS3356
CLIC-R TYPE HOSE CLAMP PLIERS
Installs and removes Clic-R hose clamps
Spring loaded gauged steel designed for ease of opera on
PVC coated handles for comfort grip
BS2110
VACUUM HOSE REMOVAL PLIERS
Drop forged chrome vanadium steel socket and sha with heat
treated and chrome plated finish
Carbon-steel handles provide solid opera on
Length: 300mm
BS2904
DOUBLE EAR HOSE CLAMP PLIERS
Crimps double ear hose clamps
Side and top join applica ons
BS9314
STAINLESS CUTTING SCISSORES
Mul -purpose scissors which is able to cut variety of things as
wood s cks, cables, hoses pipes thin metal sheet etc
A special angle designed grounds in one scissor blade to hold
cables or pipes from slipping when cu翿 ng
96
BS2865
BS2866
BS2867
BS2868
7” RETAINING & SNAP RING PLIERS
Helps easily remove and install snap rings
Made with drop forged steel and heat treated, provides durable operaon
BS2865: Internal straight
BS2866: Internal 90 angle
BS2867: External straight
BS2868: External 90 angle
GENERAL SERVICE TOOLS
BS80005
LOCKING PLIER
Heavy-duty and mul -purpose jaws design, ideal for welding,
mechanics, plumbing and DIY, etc
97
BS80056
12PC MULTI-FUNCTION RATCHET WRENCH SET
All-in-one wrench handle designed with offset ergonomic grip and
interchangeable ratchet head mechanism
Features 6 ratchet mechanisms for 1/4”, 3/8” and 1/2” Sq. Drive
and 1/4”, 8mm and 10mm hex bits
Includes 3 universal joints and safety lock extensions in 1/4”, 3/8”
and 1/2” Sq. Drive
Ideal ratchet wrench set for all professional and DIY technicians
Made from durable chrome vanadium steel
Supplied in a sturdy metal case lined with oil resistant foam
BS2008
FLEXIBLE HOSE CLAMP NUT DRIVER
Flexible sha allows access to awkward loca ons for easy removal
and installa on of most hose clamps.
Storage handle contents an rust electroplate bits for convenience
daily opera on
98
BS2501
OIL FILTER & CLUTCH HUB SPANNER
4-prong socket 3/8” Sq.Dr.
Suits oil filter and clutch hub on most HONDA models
Heat treated steel
TORQUE ANGLE GAUGE
GENERAL SERVICE TOOLS
BS7356
Measures angle of rota on a er pre-torque load in torqueangle applica ons taking the guesswork out of ghtening
Features 1/2” male and female square drives for both sockets and wrenches
360 degree scale clearly marked in 2 degree increments and
in intervals of 10 and 30
Easily zero the gauge by turning the housing for the next
applica on
Magne c flexible suppor ng sha holds the gauge to free
your hands during opera on
99
BS91400
Patented
UNIVERSAL BEARING RACE AND SEAL INSTALL TOOL
Knocking to mount posi on of bearing
Model applied:
1. Tapered roller bearings
2. Needle roller bearings
3. Ball bearing
Diameter sizes from 22mm to 89mm
3pc Ø10 x (L) 70mm extension bar
Locked
100
Adjusted
BS4326
PORTABLE BEARING PACKER
Grease stays in the tool cavity instead of your hands
Suits bearings up to 89mm (3 1/2”)
Place the bearing on the piston and press down the cap un l the
old grease is forced out
New grease shows on top of the bearing
CABLE WIRE LUBRICATION TOOL
GENERAL SERVICE TOOLS
BS4531
Injects lubricant into cable housing
Clamps over housing and wire allow aerosol lubricant to be
connected
Once lubricant runs out the far end, the cable is lubricated
Designed to lubricate thro le and clutch cables
101
BS02961
THREADED COIL INSERT REPAIRING KIT (METRIC)
Screw-Coil: M5-0.8 x 1.5D, M6-1.0 x 1.5D, M8-1.25 x 1.5D
M10-1.5 x 1.5D, M12-1.75 x 1.5D
Drill size: 5.2, 6.3, 8.3, 10.5, 12.5mm
BS9725
BS9728
PROFESSIONAL PERSONAL TOOL PACK EASY HANDY TOOL PACK
Convenient tool carrying pack designed to organize and
protect tools
Hanging holes for easy wall installa on or workbench
Designed specifically for metric motorcycles
102
Convenient tool storage pack designed to organize and
protect tools
Pack size: 6 x 18cm
Fits metric and SAE 6 point, 12 point, TX-Star, Square, 30%
round off, Spline and Ribe nuts
1. 1/4” Sq. Dr. Ratchet Handle
2. 7pc Mul Driver Sockets and 1/4” Sq. Dr. x 1/4” Hex
Adaptor (5, 6, 8, 10, 12 and 14mm )
3. 1/4” Sq. Dr. x (L) 70mm Extension Bar
4. 16pc Bits:
Hex Bits: 2, 2.5, 3, 4, 5, 6, 7 and 8mm
Flat Bits: 3, 4, 5.5 and 6.5mm
Phillips Bits: PH0, PH1, PH2, PH3
A
B
C
BS1130
3PC DETAIL BRUSH SET
Compact plas c handle consists of nylon, brass and stainless steel
bristles
Ideal for cleaning dirt, rust peeled paint or detailed parts for all
kind of motorcycles
Length: 180mm (7”)
(A-Nylon brush, B-Brass brush, C-Stainless steel brush)
BS67500
HARLEY-DAVIDSON CLUTCH SPRING COMPRESSOR
TOOL
GENERAL SERVICE TOOLS
Essen al tool used to compress the clutch spring for removal and
installa on of the retainer ring during clutch replacement
5/16” UNF internal thread for all Big Twin (1990-1997)
7/16” UNF external thread for all XL models (1991-2005)
Includes all Buell ® (1991-2003) and Buell ® Blast, except 1125R
OEM reference: 38515
BS9506
ALLOY WHEEL CLEANING BRUSH
So bristle brush suits any contours of wire or alloy wheels
Bendable to reach awkward areas
Length: 240mm (9 1/2”)
103
BS8006
4.0L PORTABLE OIL DRAIN CAN
Durable reinforced PE material stands 50kg impact
Loosening side screws assists oil-changing process
Ensures safe transporta on and storage without spillage
BS2551
FLEXIBLE SPOUT FUNNEL
Aluminium spout funnel for fluid and oil transfer
600mm flexible metal sha allows both holding or hanging easily
104
BS80031
BS80032
BS80034
RETRACTABLE RATCHET TIE DOWNS
BS80019
Part No.
Strap
Width
Strap Length
mm / in
Lashing Cap.
Breaking
Cap.
kgs / lbs
kgs / lbs
BS80031
25/1
2.4 / 8
227 / 500
680 / 1500
BS80032
25/1
1.8 / 6
227 / 500
680 / 1500
BS80034
25/1
4.5 / 15
227 / 500
680 / 1500
BS80019
47 / 1-7/8
1.2 / 4
250 / 550
1360 / 3000
GENERAL SERVICE TOOLS
No more knots, tangles or messy straps
Innova ve retractable mechanism winds up strap a er use for dy
storage
Robust all metal construc on with an -slip ratchet grip provides
superior strength and ensures long service life
Ideal for securing motorcycles, ATVs and jet skis etc. during storage or transporta on
Available in a range of lengths: 1.8 – 4.5 metres
BSG80019 are fixed type which require moun ng to trailer
All sets conform to standard AS/NZS 4380:2001
105
BS9144
17PC BUSHING DRIVE SET (METRIC)
BS4017
Removes and installs bushes on motorcycles,
cars, trucks, tractors, onstruc on equipment,
electric motors and many other applica ons
Includes 3 drive handles in metal storage case
and adapters from 10mm~42mm bushing drivers
for 14 pc
MECHANICAL BEARING PULLER SET
Suits a wide range of bearing extrac ng jobs
Includes 2” and 3” bearing spli er for pulling capacity
from 30mm to 75mm, one forged yoke and 180mm
trust bolt
Main rods extends long reach ability in maximum
170mm and 220mm
106
BS9145
19PC BUSHING DRIVE SET (SAE)
Removes and installs bushes on motorcycles,
cars, trucks, tractors, construc on equipment,
electric motors and many other applica ons
Includes 3 drive handles in metal storage case
and adapters from 3/8~1-3/8” bushing drivers
for 16 pc
BS80055
GENERAL SERVICE TOOLS
BS80054
BEARING MAINTENANCE SET (METRIC)
BEARING MAINTENANCE SYSTEM (INCH)
Suits a wide range of bearing extrac ng jobs
Includes 2” and 3” bearing spli er for pulling capacity from 30mm-75mm, one forged yoke and
180mm trust bolt
Main rods extends long reach ability in maximum
170mm and 220mm
Includes 3 drive handles in metal storage case
and adapters from 10mm-42mm bushing drivers
for 14 pc
Suits a wide range of bearing extrac ng jobs
Includes 2” and 3” bearing spli er for pulling capacity from 30mm-75mm, one forged yoke and
180mm trust bolt
Main rods extends long reach ability in maximum
170mm and 220mm
Includes 3 drive handles in metal storage case
and adapters from 3/8-1-3/8” bushing drivers for
16 pc
107
BS6100
PORTABLE WORKING STOOL
Heavy duty, rota ng wheels rated to carry loads up to 150kg
Ideal for motorcycle work
Durable plas c tray carries and stores tools, parts, nuts, bolts and
screws during motorcycle service work
Eliminates down me searching for lost tools or components
Quick and stable movement reduces the need of bending during
service
Knockdown packed for convenient transporta on and easy to assemble
BS80013
DEAD BLOW HAmmER (35mm DIA.)
90mm Long Blow Hammer
Made from oil and cold resistant SBR material, ideal for heavy and
effec ve blows
Hollow head with steel par cles inside prevents rebound
Sit
Lie down
Kneel
BS80057
3 IN 1 VERSATILITY WORKING MAT
108
Versa le working mat suitable for a wide range of applica ons
including motorcycle and automo ve repair work
Three-in-one adjustability for si翿 ng, kneeling and lying down
Made from durable 30mm thick EVA foam for comfort and support
Provides a temperature, water and oil resistant working surface
Folds for convenient storage
Dimensions: 420 x 200 x 180mm (in ‘Sit’ configura on)
Overall length: 1200mm (in ‘Lie down’ configura on)
BS9500
WATERPROOF WORKING APRON
Heavy duty working apron designed specially designed for motorcycle
repair and detailing
Premium material is waterproof and grease/oil resistant
Double layered with inbuilt s tching – outer layer resists tearing,
inner layer provides waterproofing and grease/oil resistance
Features overall type adjustable shoulder straps elimina ng stress
to neck area
Includes 9 pockets for tools, pens and notes
Ensures clothes stay dry and away from chemicals while you are
working
W : 400mm
D : Φ810mm
BS9960
GENERAL SERVICE TOOLS
H :1650mm
BIKESERVICE ROTATABLE DISPLAY STAND
Rotatable stand for Bikeservice product display perfectly
Smoothly and stably with interval holes, 2 movable shelves and 4
fixed plates, provide more flexibility for display.
Size: 400x400x1800mm
Special bearing design provides safe and smooth 360° rota on
25mm-interval hole board provides more flexibility
Contents:
4” U Hook*60pcs
109
2 movable shelves
Download PDF
Similar pages