SPOEB10xx-105 - Transition Networks

Transition Networks
SPOEB10xx-105 User Guide
SPOEB10xx-105
User Guide
•
•
•



•
Stand-Alone Media Converter
Power Over Ethernet (15.4W)
10/100Base-TX to 100Base-FX
Auto Negotiation & AutoCross
Link Pass Through & PSE enable / disable
PSE/LPT enable / disable
Far End Fault & Auto Link Restore
Contents
Introduction ......................................................................................................................................... 2
Product Description .............................................................................................................................. 2
Models .......................................................................................................................................................... 2
Optional Accessories .................................................................................................................................... 2
Distances ...................................................................................................................................................... 2
Features ............................................................................................................................................... 3
Application Example - Power over Cat5 to Remote Devices .................................................................... 3
Packing List ........................................................................................................................................... 3
Installation ........................................................................................................................................... 4
Set the Configuration DIP Switch ................................................................................................................. 4
Eight-position Configuration Switch (SW1) .................................................................................................. 4
Additional Features ...................................................................................................................................... 6
Far-End Fault (always enabled) ................................................................................................................ 6
Automatic Link Restoration (always enabled) .......................................................................................... 6
Installing Fiber Cables ................................................................................................................................... 7
Installing the Copper Cable .......................................................................................................................... 7
Connecting Power ........................................................................................................................................ 8
Operation ............................................................................................................................................. 9
Status LEDs ................................................................................................................................................... 9
PoE Status LED Scheme ................................................................................................................................ 9
Cable Specifications ............................................................................................................................ 10
Copper Cable .............................................................................................................................................. 10
Fiber Cable .................................................................................................................................................. 10
Fiber Specifications................................................................................................................................. 10
Technical Specifications ...................................................................................................................... 11
Troubleshooting ................................................................................................................................. 12
Safety Warnings and Cautions.................................................................................................................... 13
Service, Warranty and Tech Support .................................................................................................... 13
Warranty..................................................................................................................................................... 13
Contact Us .................................................................................................................................................. 13
Compliance Certifications .................................................................................................................... 14
Declaration of Conformity .......................................................................................................................... 15
Electrical Safety Warnings .......................................................................................................................... 16
Record of Revisions ............................................................................................................................. 16
33618 Rev. C
https://www.transition.com/
Page 1 of 16
Transition Networks
SPOEB10xx-105 User Guide
Introduction
The Transition Networks SPOEB10xx-105 Power over Ethernet (POE) converter is a two port 10/100Base-TX to
100Base-FX media converter capable of providing power to Data Terminal Equipment (DTE) Power Devices (PD)
via the Media Dependent Interface (MDI) twisted pair cable. The SPOEB10xx-105 emulates Power Sourcing
Equipment (PSE) and provides power via the 10/100Base-TX interface for a remote PD device that complies with
™
the IEEE802.3af standard.
The SPOEB10xx-105 lets enterprises provide power to network devices over the existing CAT5 data connection.
Transition Networks' AC powered PoE media converters combine data received over a fiber optic link with
-48VDC power; providing power to Data Terminal Equipment (DTE) Power Devices (PD) over unshielded twisted
pair (UTP) cable. The PoE converters are Power Sourcing Equipment (PSE) and are fully compatible with
Powered Devices (PDs) that comply with the IEEE802.3af™: 2003 standard. The converters also include PD
signature sensing and power monitoring features per the IEEE 802.3af standard. Other features include OverCurrent Protection, Under-Current Detection, and Fault Protection Input. This feature-enhanced model offers the
ability to enable/disable many of the features as well as force port capabilities. In addition, with the PSE/LPT
switch enabled, a loss of Fiber RX will disable PSE power output on the UTP port for two seconds to allow the
remote device to re-initialize.
The PoE converter is fully compatible with devices that comply with the IEEE802.3af standard. The PoE converter
is capable of inserting power on data pairs of the MDI.
Product Description
Models
Number
Description
SPOEB1039-105
SPOEB1040-105
10/100Base-TX RJ-45 PoE to 100Base-FX MM LC 2km
10/100Base-TX RJ-45 PoE to 100Base-FX Open SFP Slot
SPOEB1011-105
SPOEB1013-105
10/100Base-TX RJ-45 PoE to 100Base-FX MM ST 2km
10/100Base-TX RJ-45 PoE to 100Base-FX MM SC 2km
Optional Accessories
Part Number
Description
WMBL
Wall Mount Bracket: Length: 4.0 in. (102 mm), fits converter length: 4.7 in. (119mm)
WMBD
WMBV
RMS19-SA4-01
SFP Modules
DIN Rail Mount Bracket; Length: 5.0 in. (127 mm)
Vertical Wall Mount Plate; Length: 5.0 in. (127 mm)
4-Slot Media Converter Shelf
Transition Networks offers a full line of SFP Transceivers.
Distances
Number
Port One - Copper
10/100Base-TX
Port Two - Duplex Fiber-Optic
100Base-FX
SPOEB1039-105 (LC)
RJ-45 PoE; 100 m (328 ft.)*
LC, 1300nm multimode, 2km (1.2 miles)
SPOEB1040-105 (SFP)
RJ-45 PoE; 100 m (328 ft.)*
SFP, open slot
SPOEB1011-105 (ST)
RJ-45 PoE; 100 m (328 ft.)*
ST, 1300 nm multimode; 2 km (1.2 miles)
SPOEB1013-105 (SC)
RJ-45 PoE; 100 m (328 ft.)*
SC, 1300 nm multimode; 2 km (1.2 miles)
* Cable distances are typical maximum distances. Actual distance depends on the physical characteristics of
the network installation.
33618 Rev. C
https://www.transition.com/
Page 2 of 16
Transition Networks
SPOEB10xx-105 User Guide
Features















External AC power supply
IEEE 802.3af Power Over Ethernet compatible
48 VDC PSE output voltage
Applies power on the data pairs (aka Alt A, or Mode A)
PD Detection Signature
Over-Current Protection and Under-Current Detection
Powered Device (PD) Reset
PD Detection Signature
Minimum Load Sensing
Fault Protection Input
Auto-Negotiation (802.3u): allows devices to perform automatic configuration to achieve the best possible
mode of operation over a link.
™
AutoCross : automatically detects and configures the twisted pair port to the correct MDI or MDI-X
configuration.
Link Pass Through (LPT): a troubleshooting feature that lets the media converter monitor both fiber and
copper RX ports for loss of signal.
Far End Fault (FEF): a troubleshooting feature generally used with Link Pass Through to notify both end
devices of a loss of link.
Automatic Link Restoration: lets Transition Networks' converters automatically re-establish link in all
network conditions.
Application Example - Power over Cat5 to Remote Devices
Packing List
Make sure that you have received the following with your SPOEB10xx-105:




One SPOEB10xx-105 Media Converter
One external power supply (25072) and power cord (25071)
Four rubber feet
One printed Documentation Post Card
Please save the packing material for possible future use.
33618 Rev. C
https://www.transition.com/
Page 3 of 16
Transition Networks
SPOEB10xx-105 User Guide
Installation
CAUTION: All installation and service must be performed by qualified service personnel. Read and follow all
warning notices and instructions marked on the product and included in this manual.
Set the Configuration DIP Switch
The configuration switches are located on the side panel of the SPOEB10xx-105 media converter. Use a small,
flat blade screwdriver to set the switches.
Eight-position Configuration Switch (SW1)
1 - TP Autoneg - Up = TP Autoneg Enabled, Down = TP Autoneg Disabled.
2 - TP Speed - Up = TP 100Mbs, Down = TP 10 Mb/s (only when TP Autoneg Disabled).
3 - TP Duplex - Up = TP Full Duplex, Down = TP Half Duplex (only when TP Autoneg disabled).
4 - FBR Duplex - Up = FBR Full Duplex, Down = FBR Half Duplex.
5 - LPT Select – Up = LPT Enabled, Down = LPT Disabled.
6 - PSE Select - Up = PSE Enabled, Down = PSE Disabled.
7 - PSE/LPT power off LPT - Up = Disabled, Down = Enabled.
8 - Reserved.
1 - TP Auto-Negotiation
Up - Enables Auto-Negotiation.
Down - Disables Auto-Negotiation.
The Auto-Negotiation feature allows the media converter to bring up the copper links to
the highest speed and mode possible for all the attached network devices.
2 - TP Speed
Up - Forces 100 Mb/s on the copper port.
Down - Forces 10 Mb/s on the copper port.
(Only has effect when Auto-Negotiation is disabled.)
3 - TP Full/Half Duplex
Up - Full-Duplex; the twisted-pair cable distances are constrained by cable requirements.
Down - Half-Duplex; the twisted-pair cable distances are constrained by the 512-Bit Rule.
(Only has effect when Auto-Negotiation is disabled.)
33618 Rev. C
https://www.transition.com/
Page 4 of 16
Transition Networks
SPOEB10xx-105 User Guide
4 - Fiber Full/Half Duplex
Up - The cable distances for the fiber port are constrained by the cable requirements.
Down - The cable distances for the fiber port are constrained by the 512-Bit Rule.
5 - LPT – Link Pass Through
Up - Enables the LPT function.
Down - Disables the LPT function.
The Link Pass-Through allows the media converter to monitor both the fiber and copper
RX (receive) ports for loss of signal. In the event of a loss of an RX signal on one media
port, the media converter will automatically disable the TX (transmit) signal of the other
media port, thus, “passing through” the link loss. The far-end device is automatically
notified of the link loss, which prevents the loss of valuable data unknowingly transmitted
over an invalid link. See diagram below.
6 - PSE Power
Up - Enables PSE power.
Down - Disables PSE power.
The IEEE 802.3af™ standard allows a device to provide power (PSE - Power Sourcing
Equipment) to a remote device and for a remote device (PD - Powered Device) to accept
and use this power over a twisted pair interface.
7 - PSE/LPT (POE power off LPT - OPEN = Disabled)
Up - Disable PSE/LPT.
Down - Enable PSE/LPT.
This feature is used to re-initialize a powered device (PD). If the fiber RX (receive) link
drops with the PSE/LTP switch in the enabled position (down), the PSE power
will turn OFF for two seconds then turn back ON to re-start the remote device.
The power will remain ON to allow the remote PD to re-establish the link with the
media converter. Note that this feature requires DIP switch 5 (LPT) to also be enabled.
8 - Reserved
Reserved for future use.
33618 Rev. C
https://www.transition.com/
Page 5 of 16
Transition Networks
SPOEB10xx-105 User Guide
Additional Features
Far-End Fault (always enabled)
This troubleshooting feature is generally used in conjunction with Link Pass Through to notify both end devices
of a link loss. If the fiber RX signal is lost on the far end converter, the converter will automatically generate a
far-end
fault signal and send it on its TX fiber port to notify the near-end converter of the fiber link loss. Link PassThrough will then disable the copper link on both ends, alerting both end devices of network trouble. See
diagram below.



Both end devices are notified automatically of the link loss
Prevents loss of valuable data transmitted unknowingly over invalid link
Allows quick diagnosis and resolution of network problem
Transition Networks’ media converters that include the FEF feature will work with other network devices that
support Far End Fault per IEEE standards.
Automatic Link Restoration (always enabled)
Transition Networks’ converters will automatically re-establish the link in all network conditions:



Without a device reset, the converters will automatically re-establish the link when connected to
switches after a link loss.
With Auto-Negotiation enabled, automatic link restoration allows using Auto-Negotiation with Link-Loss
Notification.
With Link Pass-Through enabled in both directions, automatic link restoration allows using Link-Loss
Notification in both directions.
33618 Rev. C
https://www.transition.com/
Page 6 of 16
Transition Networks
SPOEB10xx-105 User Guide
CAUTION: Associated Ethernet wiring must be limited to inside the building.
Installing Fiber Cables
1. Locate a 100Base-FX fiber cable with male, two-stranded TX to RX connectors installed at both ends.
2. Connect the fiber cables to the SPOEB10xx-105 media converter as described:
• Connect the male TX cable connector to the female TX port.
• Connect the male RX cable connector to the female RX port.
3. Connect the fiber cables to the other device (another media converter, hub, etc.) as follows:
• Connect the male TX cable connector to the female RX port.
• Connect the male RX cable connector to the female TX port.
Installing the Copper Cable
1. Locate 100Base-TX copper cables with male, RJ-45 connectors installed at both ends.
2. Connect the RJ-45 connector at one end of the cable to the RJ-45 port on the media converter.
3. Connect the RJ-45 connector at the other end of the cable to the RJ-45 port on the other device (wireless
access point, VoIP phone, network camera, etc.).
33618 Rev. C
https://www.transition.com/
Page 7 of 16
Transition Networks
SPOEB10xx-105 User Guide
Connecting Power
Use only the Power Supply that shipped with the SPOEB.
1. Connect the barrel connector on the power adapter to the power port on the media converter (back panel).
2. Connect the power adapter plug to AC power.
3. Verify that the front panel PWR LED is lit indicating the SPOEB is powered.
External 90 - 250 VAC Power Supply (TN# 25072) US Power Cord (25071) and SPOEB
Power Supply Included: To order the corresponding country specific power supply, add the Country Code
extension to the end of the SKU: -NA = North America, -LA = Latin America, -EU = Europe, -UK = United Kingdom,
-SA = South Africa, -JP = Japan, -OZ = Australia, -BR = Brazil.
33618 Rev. C
https://www.transition.com/
Page 8 of 16
Transition Networks
SPOEB10xx-105 User Guide
Operation
Status LEDs
The SPOEB10xx-105 front panels are shown below.
SPOEB1039-105
SPOEB1040-105
SPOEB1011-105
SPOEB1013-105
The SPOEB10xx-105 front panel LEDs are described below.
LED
Description
PWR
Device Power. Green = Power ON.
LACT (fiber)
Fiber Link Activity. Green: ON = Link, Blinking = activity.
DPX (fiber)
Fiber Duplex mode. Green: ON = Full, OFF = Half.
LACT (TP)
TP Link Activity. Green: ON = Link, Blinking = activity.
SPD (TP)
TP Speed. Green: ON = 100Mb/s, OFF = 10Mb/s.
DPX (TP)
TP Duplex mode. Green: ON = Full, OFF = Half, Blinking = collision.
POE STAT
Power over Ethernet State. Green: ON = Enabled, OFF = Disabled.
LACT = Link Activity. DPX = Duplex. SPD = Speed. TP = Twisted Pair. LTC = PoE controller.
PoE Status LED Scheme
The PoE controller component provides the following LED reporting:
LED Condition
Meaning
LED Off
Non-Powered Device: 0 ohms < RPORT < 200 ohms.
LED Off
Port Open: RPORT > 1M ohms.
LED On
Port On: 25k ohms.
1 Flash
Low Signature Resistance: 300 ohms < RPORT < 15k ohms.
2 Flashes
High Signature Resistance: 33k ohms < RPORT < 500k ohms.
5 Flashes
Port Overload Fault.
9 Flashes
Power Management: Allocation Exceeded.
33618 Rev. C
https://www.transition.com/
Page 9 of 16
Transition Networks
SPOEB10xx-105 User Guide
Cable Specifications
™
The cable’s physical characteristics must meet or exceed IEEE 802.3 specifications.
Copper Cable
Category 5: (Minimum Requirement)
Gauge: 24 to 22 AWG
Attenuation: 22.0 dB /100m @ 100 MHz
• Straight-through OR crossover twisted-pair cable may be used.
• Shielded twisted-pair (STP) OR unshielded Twisted-pair (UTP) may be used.
• Pins 1&2 and 3&6 are the two active pairs in an Ethernet network.
• RJ-45 Pin-out: Pin 1 = TD+, Pin 2 = TD-, Pin 3 = RD+, Pin 6 = RD-.
• Use only dedicated wire pairs for the active pins:
(e.g., blue/white & white/blue, orange/white & white/orange, etc.)
• Do not use flat or silver satin wire.
Fiber Cable
The fiber optic transmitters on this device meet Class I Laser safety requirements per IEC-825/CDRH standards
and comply with 21 CFR1040.10 and 21CFR1040.11.
Fiber Specifications
SPOEB1011-105 (ST)
SPOEB1013-105 (SC)
SPOEB1039-105 (LC)
1x9, 850nm, ST, MM, 3.3V
Multimode, Dual fiber, Distance = 2km,
Wavelength = 1310 nm
Data rate = 100Mbps
Max Spectral Width = 400.0nm FWHM
1x9, 850nm, SC, MM, 3.3V
Multimode, Dual fiber, Distance = 2km,
Wavelength = 1310nm
Data rate = 100Mbps
Max Spectral Width = 400.0nm FWHM
Min Tx Power=-19.0 dBm
Max Tx Power=-14.0 dBm
Rx Sensitivity=-30.0 dBm
Rx Max In Power=-14.0 dBm
Link Budget=11.0 dB
MN Tx Power = -19.0 dBm
Max Tx Power = -14.0 dBm
Rx Sensitivity = -30.0 dBm
Rx Max In Power = -14.0 dBm
Link Budget = 11.0 dB
Multi Mode
Dual Fiber
Wavelength = 1310 nm
Laser transmitter
TN PN 13300
Spectral Width Max. = 147.0nm FWHM
Min. TX Power = -19.0 dBm
Max. TX Power = -14.0 dBm
RX Sensitivity = -30.0 dBm
RX Max. In Power = -14.0 dBm
Link Budget = 11.0 dB
33618 Rev. C
https://www.transition.com/
Page 10 of 16
Transition Networks
SPOEB10xx-105 User Guide
Technical Specifications
For use with Transition Networks SPOEB10xx-100 or equivalent.
Standards
Data Rate
Max Frame Size
Mac Addresses
Dimensions
Weight
Power Consumption
Power Supply
Environment Tmra
Storage Temp.
Humidity
Altitude
MTBF
IEEE 802.3, IEEE 802.3af
10/100 Mbps
1600 bytes (with or without VLAN tag)
2K
3.25" x 1” x 4.8" (82 mm x 25.4mm x 120mm)
Device: 0.8 lbs. [362 g] approx. Package: 2 lbs. [0.90 kg].
25 Watts
External Isolated Class II 30W Power Supply: 90 – 250 VAC (TN# 25072)
0° to 40°C (32° to 104°F) (Manufacturer’s rated ambient operating temperature)
-25° to +85°C (-13° to +185°F)
5% to 95%, non-condensing
0 to 10,000 feet
49,981 MIL217F2 Hours; 132,144 Bellcore Hours*
Compliance
EN55022:1994+A1:1996+A2:1997 Class A, FCC Part 15 Subpart B, UL 1950
Lifetime
Warranty
Note: The information in this user’s guide is subject to change. For the most up-to-date information on the
SPOEB10xx-100 media converter, view the user’s guide on-line at: https://www.transition.com.
Product is certified by the manufacturer to comply with DHHS Rule 21/CFR, Subchapter J applicable at the date of
manufacture.
WARNING: Visible and invisible laser radiation when open. Do not stare into the beam or view the beam directly with optical
instruments. Failure to observe this warning could result in an eye injury or blindness.
WARNING: Use of controls, adjustments or the performance of procedures other than those specified herein may result in
hazardous radiation exposure.
WARNING: If the media converter is an IEEE802.3-2005 Powered Device (PD) capable of receiving power via the Media
Dependent Interface (MDI) leads, the power source, connector, and cabling attached to the barrel power connector must meet
the isolation requirement specified in IEEE802.3-2005. Failure to observe this warning could result in an electrical shock.
IMPORTANT Copper based media ports, e.g., Twisted Pair (TP) Ethernet, USB, RS232, RS422, RS485, DS1, DS3, Video
Coax, etc., are intended to be connected to intra-building (inside plant) link segments that are not subject to lightening
transients or power faults. Copper based media ports, e.g., Twisted Pair (TP) Ethernet, USB, RS232, RS422, RS485, DS1,
DS3, Video Coax, etc., are NOT to be connected to inter-building (outside plant) link segments that are subject to lightening
transients or power faults. Failure to observe this caution could result in damage to equipment.
* MTBF is estimated using the predictability method. This method is based on MIL-217F at 25°C ambient temperature, typical
enclosure heat rise of 10°C, and nominal operating conditions and parameters. Installation and configuration specific MTBF
estimates are available upon request. Contact Technical Support.
33618 Rev. C
https://www.transition.com/
Page 11 of 16
Transition Networks
SPOEB10xx-105 User Guide
Troubleshooting
If the media converter fails, isolate and correct the fault by determining the answers to the following questions and
then take the indicated action:
1.
Is the media converter PWR LED lit?
NO:
• Is the barrel connector fully inserted into the media converter?
• Is the adapter plugged into an AC outlet; if not, plug it into the outlet.
• Is the AC outlet active? If not, check the outlet’s circuit beaker
• Contact Technical Support; see “Contact Us” below.
YES
• Go to step 2.
2.
Is the POE STAT LED lit?
NO
• Is there an active (connected to another device) RJ-45 cable inserted into the media converter's TX port;
if not, insert the cable accordingly.
• Is power turned on and the power LED lit on the other device? See “Status LEDs” on page 9.
• Contact Technical Support; see “Contact Us” below.
YES
• Go to step 3.
3.
Is the copper TP LACT LED lit?
NO
• Check the twisted pair cables for proper installation in the device at both ends.
• Disconnect and reconnect the twisted pair cable to restart the initialization process.
• Restart the attached device to restart the initialization process.
• Contact Technical Support; see “Contact Us” below.
YES
• Go to step 4.
4.
Is the fiber RX LACT LED lit?
NO
• Check the fiber cables for proper connection.
• Verify that the TX and RX cables on the media converter are connected to the RX and TX ports,
respectively, on the other device.
• Disconnect and reconnect the fiber cable to restart the initialization process.
• Restart the attached device to restart the initialization process.
• Contact Technical Support; see “Contact Us” below.
YES
• Go to step 5.
5.
Is data being passed through the device?
NO
• Ensure the Powered Device (PD) IEEE 802.3af compliant.
• Ensure the load to the Powered Device (PD) is less than 0.4 Amp.
• Is a data source connected; if not, connect a data source to the media converter.
• Is the data source active; if not, start sending data.
• Are the FX LACT and TX LACT LEDs flashing? See “Status LEDs” on page 9.
• Verify the DIP switch settings. See “Set the Configuration DIP Switch” on page 4.
• Check the fiber SPD LED condition. See “Status LEDs” on page 9.
• Check the fiber DPX LED condition. See “Status LEDs” on page 9.
• Contact Technical Support; see “Contact Us” below.
33618 Rev. C
https://www.transition.com/
Page 12 of 16
Transition Networks
SPOEB10xx-105 User Guide
Safety Warnings and Cautions
These products are not intended for use in life support products where failure of a product could reasonably be expected to
result in death or personal injury. Anyone using this product in such an application without express written consent of an
officer of Transition Networks does so at their own risk, and agrees to fully indemnify Transition Networks for any damages
that may result from such use or sale.
Attention: this product, like all electronic products, uses semiconductors that can be damaged by ESD (electrostatic
discharge). Always observe appropriate precautions when handling.
Warning: Potential for damage to equipment or personal injury.
Warning: Risk of Electrical Shock
Service, Warranty and Tech Support
Warranty
Limited Lifetime Warranty
Effective for Products Shipped May 1, 1999 and After. Every Transition Networks labeled product purchased after May 1,
1999, and not covered by a fixed-duration warranty will be free from defects in material and workmanship for its lifetime.
This warranty covers the original user only and is not transferable.
This warranty does not cover damage from accident, acts of God, neglect, contamination, misuse or abnormal conditions of
operation or handling, including over-voltage failures caused by use outside of the product's specified rating, or normal
wear and tear of mechanical components. If the user is unsure about the proper means of installing or using the
equipment, contact Transition Networks’ free technical support services.
Transition Networks will, at its option:
• Repair the defective product to functional specification at no charge
• Replace the product with an equivalent functional product
• Refund a portion of purchase price based on a depreciated value
Return Authorization
To return a defective product for warranty coverage, contact Transition Networks’ technical support department for a
return authorization number. Transition's technical support department can be reached through any of the following
means:
Contact Us
Technical Support: Technical support is available 24-hours a day
US and Canada: 1-800-260-1312 | International: 00-1-952-941-7600
Main Office
tel: +1.952.941.7600 | toll free: 1.800.526.9267 | fax: 952.941.2322
sales@transition.com | techsupport@transition.com | customerservice@transition.com
Address
Transition Networks | 10900 Red Circle Drive | Minnetonka, MN 55343, U.S.A.
33618 Rev. C
https://www.transition.com/
Page 13 of 16
Transition Networks
SPOEB10xx-105 User Guide
Return Instructions
Send the defective product postage and insurance prepaid to the following address:
Transition Networks, Inc.
10900 Red Circle Drive
Minnetonka, MN 55343 USA
Attn: RETURNS DEPT: CRA/RMA # ___________
Failure to properly protect the product during shipping may void this warranty. The return authorization number must be
written on the outside of the carton to ensure its acceptance. We cannot accept delivery of any equipment that is sent to us
without a CRA or RMA number.
CRA’s are valid for 60 days from the date of issuance. An invoice will be generated for payment on any unit(s) not returned
within 60 days.
Upon completion of a demo/ evaluation test period, units must be returned or purchased within 30 days. An invoice will be
generated for payment on any unit(s) not returned within 30 days after the demo/ evaluation period has expired.
The customer must pay for the non-compliant product(s) return transportation costs to Transition Networks for evaluation
of said product(s) for repair or replacement. Transition Networks will pay for the shipping of the repaired or replaced inwarranty product(s) back to the customer (any and all customs charges, tariffs, or/and taxes are the customer's
responsibility).
Before making any non-warranty repair, Transition Networks requires a $200.00 charge plus actual shipping costs to and
from the customer. If the repair is greater than $200.00, an estimate is issued to the customer for authorization of repair. If
no authorization is obtained, or the product is deemed “not repairable”, Transition Networks will retain the $200.00 service
charge and return the product to the customer not repaired.
Non-warranted products that are repaired by Transition Networks for a fee will carry a 180-day limited warranty. All
warranty claims are subject to the restrictions and conventions set forth by this document.
Transition Networks reserves the right to charge for all testing and shipping incurred, if after testing, a return is classified as
"No Problem Found."
THIS WARRANTY IS YOUR ONLY REMEDY. NO OTHER WARRANTIES, SUCH AS FITNESS FOR A PARTICULAR PURPOSE, ARE
EXPRESSED OR IMPLIED. TRANSITION NETWORKS IS NOT LIABLE FOR ANY SPECIAL, INDIRECT, INCIDENTAL OR
CONSEQUENTIAL DAMAGES OR LOSSES, INCLUDING LOSS OF DATA, ARISING FROM ANY CAUSE OR THEORY. AUTHORIZED
RESELLERS ARE NOT AUTHORIZED TO EXTEND ANY DIFFERENT WARRANTY ON TRANSITION NETWORKS'S BEHALF.
Compliance Certifications
CISPR22/EN55022 Class A
CE Mark
FCC Regulations
This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to part 15 of the
FCC rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is
operated in a commercial environment. This equipment generates, uses, and can radiate radio frequency energy and, if not
installed and used in accordance with the instruction manual, may cause harmful interference to radio communications.
Operation of this equipment in a residential area is likely to cause harmful interference, in which case the user will be
required to correct the interference at the user's own expense.
Canadian Regulations
This digital apparatus does not exceed the Class A limits for radio noise for digital apparatus set out on the radio
interference regulations of the Canadian Department of Communications.
Le présent appareil numérique n'émet pas de bruits radioélectriques dépassant les limites applicables aux appareils
numériques de la Class A prescrites dans le Règlement sur le brouillage radioélectrique édicté par le ministère des
Communications du Canada.
33618 Rev. C
https://www.transition.com/
Page 14 of 16
Transition Networks
SPOEB10xx-105 User Guide
European Regulations
Warning
This is a Class A product. In a domestic environment this product may cause radio interference in which case the user may
be required to take adequate measures.
Achtung !
Dieses ist ein Gerät der Funkstörgrenzwertklasse A. In Wohnbereichen können bei Betrieb dieses Gerätes
Rundfunkstörungen auftreten. In diesem Fäll ist der Benutzer für Gegenmaßnahmen verantwortlich.
Attention !
Ceci est un produit de Classe A. Dans un environment domestique, ce produit risque de créer des interférences
radioélectriques, il appartiendra alors à l'utilsateur de prende les measures spécifiques appropriées.
In accordance with European Union Directive 2002/96/EC of the European Parliament and of the Council of 27
January 2003, Transition Networks will accept post usage returns of this product for proper disposal. The
contact information for this activity can be found in the 'Contact Us' portion of this document.
CAUTION: RJ connectors are NOT INTENDED FOR CONNECTION TO THE PUBLIC TELEPHONE NETWORK. Failure
to observe this caution could result in damage to the public telephone network.
Der Anschluss dieses Gerätes an ein öffentlickes Telekommunikationsnetz in den EGMitgliedstaaten verstösst gegen die
jeweligen einzelstaatlichen Gesetze zur Anwendung der Richtlinie 91/263/EWG zur Angleichung der Rechtsvorschriften der
Mitgliedstaaten über Telekommunikationsendeinrichtungen einschliesslich der gegenseitigen Anerkennung ihrer
Konformität.
Declaration of Conformity
33618 Rev. C
https://www.transition.com/
Page 15 of 16
Transition Networks
SPOEB10xx-105 User Guide
Electrical Safety Warnings
Electrical Safety
IMPORTANT: This equipment must be installed in accordance with safety precautions.
Elektrische Sicherheit
WICHTIG: Für die Installation dieses Gerätes ist die Einhaltung von Sicherheitsvorkehrungen erforderlich.
Elektrisk sikkerhed
VIGTIGT: Dette udstyr skal installers I overensstemmelse med sikkerhedsadvarslerne.
Elektrische veiligheid
BELANGRIJK: Dit apparaat moet in overeenstemming met de veiligheidsvoorschriften worden geïnstalleerd.
Sécurité électrique
IMPORTANT : Cet équipement doit être utilisé conformément aux instructions de sécurité.
Sähköturvallisuus
TÄRKEÄÄ : Tämä laite on asennettava turvaohjeiden mukaisesti.
Sicurezza elettrica
IMPORTANTE: questa apparecchiatura deve essere installata rispettando le norme di sicurezza.
Elektrisk sikkerhet
VIKTIG: Dette utstyret skal enstallers I samsvar med sikkerhetsregler.
Segurança eléctrica
IMPORTANTE: Este equipamento tem que ser instalado segundo as medidas de precaução de segurança.
Seguridad eléctrica
IMPORTANTE: La instalación de este equipo deberá llevarse a cabo cumpliendo con las precauciones de seguridad.
Elsäkerhet
OBS! Alla nödvändiga försiktighetsåtgärder måste vidtas när denna utrustning används.
Record of Revisions
Rev
Date
Description of Changes
A
7/15/15
Release for SPOEB10xx-105. All pages at Rev. A.
B
12/30/15
Add SPOEB1011-105 and SPOEB1013-105. Update DIP switch and Troubleshooting sections.
C
11/29/17
Update DIP switch 8 description and contact information.
Trademark notice: All trademarks and registered trademarks are the property of their respective owners. All other products
or service names used in this publication are for identification purposes only, and may be trademarks or registered
trademarks of their respective companies. All other trademarks or registered trademarks mentioned herein are the
property of their respective holders.
Copyright restrictions: © 2004-2017 Transition Networks, Inc. All rights reserved. No part of this work may be reproduced
or used in any form or by any means (graphic, electronic, or mechanical) without written permission from Transition
Networks.
Address comments on this product or manual to:
Transition Networks Inc.
10900 Red Circle Drive
Telephone: +1-952-941-7600 / Toll Free: 800-526-9267 / Fax: 952-941-2322
E-Mail: customerservice@transition.com / techsupport@transition.com sales@transition.com
33618 Rev. C
https://www.transition.com/
Page 16 of 16
Download PDF
Similar pages