Van mechelen bvba
Patersstraat 106-108 2300 turnhout
Gasthuisstraat 21 2440 geel
Kempen antwerpen noorderkempen limburg
014/41.12.08 014/42.55.99 014/59.26.95
www.vanmechelen.be
be0415638961 145.638.961
dexia 068-2221350-77
hrt41.156
kantoormachines – kantoormaterialen kassa weegschaal horeca systemen
VLIMMEREN(BEERSE) WECHELDERZANDE
ZOERSEL BRECHT MERKSEM LOENHOUT WUSTWEZEL EKEREN(ANTWERPEN) HERENTALS MORKHOVEN NOORDERWIJK
PULDERBOS PULLE OLEN OEVEL TONGERLO(ANTW) WESTERLO ZOERLE-PARWIJS HERENTHOUT GIERLE LILLE
POEDERLEE WECHELDERZANDE GROBBENDONK VORSELAAR TURNHOUT RIJKEVORSEL HOOGSTRATEN MEER
MINDERHOUT WORTEL MEERLE MERKSPLAS BAARLE-HERTOC BEERSE VLIMMEREN VOSSELAAR OUD—TURNHOUT
ARENDONK RAVELS WEELDE POPPEL BAARLE-HERTOG MALLE OOSTMALLE WESTMALLE POPPEL(RAVELS) MOL
HERENTALS LILLE POEDERLEE(LILLE) HERENTALS(NOORDERWIJK) EINDHOUT LAAKDAL VORST(KEMPEN) LAAKDAL
VARENDONK VEERLE GEEL MEERHOUT GIERLE(LILLE) KASTERLEE ICHTAART TIELEN RETIE DESSEL BALEN
OLMEN KALMTHOUT BRASSCHAAT HOEVENEN STABROEK BRECHT SINT-JOB-IN-’T-GOOR SINT-LENAERTS
HALLE(KEMPEN) HALLE(KEMPEN) ZOERSEL LOENHOUT WUUSTWEZEL OVERPELT NEERPELT SINT-HUIBRECHT-LILLE
LOMMEL ACHEL HAMONT HAMONT-ACHEL HECHTEL EKSEL HAM KWAADMECHELEN OOSTHout BOCHOLT KAULILLE
REPPEL BEEK BREE GERDINGEN OPITTER TONGERLO(LIMB) LEOPOLDSBURC HEPPEN TESSENDERLO CROTE-BROGEL
KLEINE-BROGEL PEER WIJCHMAAL LAAKDAL LAAKDAL
DOT MATRIX PRINTER
MODEL iDP3550/3551
Patersstraat 106-108
2300 Turnhout
Tel:014/42.55.99
Fax: 014/42.32.64
BTW BE 0415.638.961
Rek: 230-0026460-96
info@vanmechelen.be
www.vanmechelen.be
www.vanmechelen.be KANTOORMACHINES – KANTOORMATERIALEN
TURNHOUT - GEEL
iDP3550/3551 User’s Manual
Declaration of Conformity
Manufacturer’s Name :
Manufacturer’s Address
Declare the Product
Product Name
Model Number(s)
Conform to the following Standards
LVD
EMC
: Japan CBM Corporation
: CBM Bldg., 5-68-10, Nakano, Nakano-ku,
Tokyo, 164-0001, Japan
Dot Matrix Printer
iDP3550/3551 Series
(iDP3550/3551 RF/PF, iDP3550/3551 SF/CF, iDP3550/3551 TF/IF)
(S.No. 0090001 ~
)
: EN60950
: EN55022
: EN61000-3-2
: EN61000-3-3
: EN55024
: EN61000-4-2
: EN61000-4-3
: EN61000-4-4
: EN61000-4-5
: EN61000-4-6
: EN61000-4-8
: EN61000-4-11
: A4:1997, A11:1997
: 1998 Class A
: 1995+A1:1998+A2:1998
: 1995
: 1998
: 1995 ±4KV CD, ±8KV AD
: 1996 4.5V/m, 80MHz-1000MHz AM 1KHz 80%
: 1995 ±1.0KV(AC Mains), ±0.5KV(Signal Lines)
: 1995 ±1KV (Normal mode), ±2KV (Common mode)
: 1996 3V, 0.15MHz-80MHz AM 1KHz 80%
: 1993 50Hz, 3A/m
: 1994 0%, 5000ms/ 70%, 500ms/ 0%, 10ms
Supplementary Information
“The product complies with the requirements of the Low Voltage Directive 73/23/EEC, 93/68/EEC and
the EMC Directive 89/336EEC, 92/31/EEC, 93/68EEC”
Place
Tokyo, Japan
Date
September, 2000
Signature
Full Name
Position
: Mikio Moriya
: General Manager
R & D Department
Europe Contact :
Norco Declaration AB
Box 7146 S-250 07 Helsingborg Sweden
Warning : This is a Class A products. In a domestic environment this product may cause radio interference in
which case the user may be required to take adequate measures.
This declaration is applied only for 230V model.
CITIZEN
www.vanmechelen.be KANTOORMACHINES – KANTOORMATERIALEN
TURNHOUT - GEEL
iDP3550/3551 User’s Manual
IMPORTANT SAFETY INSTRUCTIONS
•
•
•
•
•
•
•
•
•
•
•
•
•
Read all of these instructions and save them for future reference.
Follow all warnings and instructions marked on the product.
Unplug this product from the wall outlet before cleaning. Do not use liquid or aerosol cleaners.
Use a damp cloth for cleaning.
Do not use this product near water.
Do not place this product on an unstable cart, stand or table. The product may fall, causing serious
damage to the product.
Slots and openings on the back or bottom of the case are provided for ventilation. To ensure reliable
operation of the product and to protect it from overheating, do not block or cover these openings.
The openings should never be blocked by placing the product on a bed, sofa, rug of other similar
surface. This product should never be placed near or over a radiator or heater. This product should
not be placed in an built-in installation unless proper ventilation is provided.
This product should be operated from the type of power source indicated on the marking label. If
you are not sure of the type of power available, consult your dealer or local power company.
Do not allow anything to rest on the power cord. Do not place this product where the cord will be
walked on.
If an extension cord is used with this product, make sure that the total of the ampere ratings of the
products plugged into the extension cord does not exceed the extension cord ampere rating. Also,
make sure that the total of all products plugged into the wall outlet does not exceed 15 amperes.
Never push objects of any kind into this product through cabinet slots as they may touch dangerous
voltage points or short out parts that could result in a risk of fire or electric shock. Never spill liquid
of any kind on the product.
Except as explained elsewhere in this manual, do not attempt to service this product by yourself.
Opening and removing the covers that are marked “Do Not Remove” may expose you to dangerous
voltage points or other risks. Refer all servicing on those compartments to service personnel.
Unplug this product from the wall outlet and refer servicing to qualified service personnel under the
following conditions:
A. When the power cord or plug is damaged or frayed.
B. If liquid has been spilled into the product.
C. If the product has been exposed to rain or water.
D. If the product does not operate normally when the operating instructions are followed. Adjust
only those controls that are covered by the operating instructions since improper adjustment of other
controls may result in damage and will often require extensive work by a qualified technician to
restore the product to normal operation.
E. If the product has been dropped or the cabinet has been damaged.
F. If the product exhibits a distinct change in performance, indicating a need for s ervice.
Please keep the poly bag which this equipment is packed in away from children or throw it away to
prevent children from putting it on. Putting it on may cause suffocation.
CITIZEN
iDP3550/3551 User’s Manual
WICHTIGE SICHERHEITSANWEISUNGEN
•
•
Lesen Sie die nachfolgenden Anweisungen sorgfältig durch und bewahren Sie sie auf.
Befolgen Sie alle auf dem Drucker vermerkten Hinweise und Anweisungen. Vor dem
Reinigen grundsätzlich Stecker aus der Steckdose ziehen. Keine Flüssigkeiten oder Aerosolreiniger
benutzen. Nut mit einem feuchten Tuch abwischen.
• Der Drucker darf nicht in der Nähe von Wasser aufgestellt werden.
• Drucker nicht auf einem unstabilen Wagen, Stand oder Tisch aufstellen. Der Drucker
könnte herunterfallen und dabel beschädigt werden.
• Schlitze und Öffnungen im Gehäuse, in der Rückwand und im Boden dienen der Belüftung. Sie
dürfen keinesfalls zugedeckt oder blockiert werden, da sich der Drucker sonst überhitzt. Drucker
nicht auf ein Bett, Sofa, Teppich oder dergleichen stellen. Drucker nicht in der Nähe eines
Heizkörpers aufstellen. Drucker darf nicht eingebaut werden, falls nicht für ausreichende Belüftung
gesorgt ist.
• Drucker nur mit der auf dem Typschild angegebenen Spannung betreiben. Wenn Sie sich nicht sicher
sind, fragen Sie ihren Händler oder ihr zuständiges Elektrizitätswerk.
• Nichts auf das Stromanschlußkabel stellen. Kabel muß so verlegt werden, daß man nicht
darauftreten kann.
• Ein etwaiges Verlängerungskabel muß der Stromstärke aller daran angeschlossenen Geräte
entsprechen.
• Keine Gegenstände in die Gehäuseschlitze schieben.
• Drucker darf nur da gewartet werden, wo im Handbuch angegeben, Öffnen und.
Abnehmen von Abdeckungen, die mit “Do not remove” gekennzeichenet sind, könnte gefährliche
spannungführende Stellen oder sonstige Gefahrenpunkte freilegen. Die wartung solcher Stellen darf
grundsätzlich nur von besonders ausgebildetem Fachpersonal vorgenommen werden.
A. Wenn das Stromanschlußkabel oder der Stecker beschädigt oder durch-gescheuert ist.
B. Wenn Flüssigkeit auf dem Drucker verschüttet wurde.
C. Wenn der Drucker im Regen gestanden hat oder Wasser darauf verschüttet wurde.
D. Wenn der Drucker trotz genauer Befolgung der Betriebsvorschriften nicht richtig arbeitet. Nur die
in der Bedienungsanleitung angegebenen Einstellungen vornehmen. Ein Verstellen anderer
Bedienungselemente könnte den Drucker beschädigen und macht umständliche Arbeiten eines
qualifizierten Technikers erforderlich, um den Drucker Wieder auf den normalen Betrieb
einzustellen.
E. Wenn der Drucker heruntergefallen ist oder das Gehäuse beschädigt wurde.
F. Wenn der Drucker in seiner Leistung nachläßt.
• Bitte halten Sie den Kunststoffbeutel, in den die Ware verpackt ist, von Kindern entfernt, oder werfen
Sie ihn weg, damit er nicht in die Hande von Kindern gerät. Das
Überstülpen des Beutels kann zum Ersticken führen.
Lärmemission kleiner 70dBA
CITIZEN
iDP3550/3551 User’s Manual
IMPORTANT: This equipment generates, uses, and can radiate radio frequency energy and if not
installed and used in accordance with the instruction manual, may cause interference to radio
communications.
It has been tested and found to comply with the limits for a Class A computing device
pursuant to Subpart J of Part 15 off FCC Rules, which are designed to provide reasonable protection
against such interference when operated in a commercial environment.
Operation of this equipment in a
residential area is likely to cause interference, in which case the user at his own expense will be required to
take whatever measures may be necessary to correct the interference.
CAUTION: Use shielded cable for this equipment.
Sicherheitshinweis
Die Steckdose zum Anschluß dieses Druckers muß nahe dem Grät angebracht und leicht zugänglich sein.
For Uses in Canada
This digital apparatus does not exceed the class A limits for radio noise emissions from digital, apparatus,
as set out in the radio interference regulations of the Canadian department of communications.
Pour L’utilisateurs Canadiens
Cet appareil numérique ne dépasse pas les limites de carégorie a pour les émissions de bruit radio émanant
d’appareils numériques, tel que prévu dans les réglements sur l’interférence radio du départment Canadien
des communications.
CITIZEN
iDP3550/3551 User’s Manual
<CAUTIONS>
1. Prior to using the equipment, be sure to read this User's Manual thoroughly.
Please keep it handy for reference
whenever it may be needed.
2. The information contained herein may be changed without prior notice.
3. Reproduction of part or all of this User's Manual without permission is strictly prohibited.
4. Never service, disassemble, or repair parts that are not mentioned in this User's Manual.
5. Note that we will not be responsible for damages attributable to a user's incorrect operation/ handling or an
improper operating environment.
6. Operate the equipment only as described in this User's Manual; otherwise accidents or problems may result.
7. Data are basically temporary; they cannot be stored or saved permanently or for a long time.
Please note that
we will not be responsible for damages or losses of profit resulting from losses of the data attributable to
accidents, repairs, tests, and so on.
8. If you have any questions or notice any clerical errors or omissions regarding the information in this manual,
please contact our office.
9. Please note that, notwithstanding Item 8 above, we will not be responsible for any effects resulting from
operation of the equipment.
CITIZEN
iDP3550/3551 User’s Manual
SAFETY PRECAUTIONS ----- BE SURE TO OBSERVE
In order to prevent hazards to an operator or other persons and damage to property, be sure to observe the following
precautions.
• The following describes the degrees of hazard and damages that can occur if the given
instructions are neglected or the equipment is incorrectly operated.
WARNING
Negligence of this precaution may result in death or serious injury.
CAUTION
Negligence of this precaution may result in injury or damage to property.
This is an illustration mark used to alert your attention.
This is an illustration mark used to indicate such information as an instruction or the like.
CITIZEN
iDP3550/3551 User’s Manual
WARNING
• Never handle the equipment in the following manners, as it may break, become out of order, or
overheat causing smoke and resulting in fire or electric shock.
If the equipment is used in an abnormal condition, such as when broken, then problems, smoke
emission, abnormal odor/noise, and fire can result. If an abnormal condition exists, be sure to turn off
the power, disconnect the power plug from a plug socket, and contact our dealer. Never repair the
equipment on your own - it is very dangerous.
• Do not allow the equipment to receive a strong impact or shock, such as kicking, stomping, hitting,
dropping, and the like.
• Install the equipment in a well-ventilated place. Do not use it in such a manner that its ventilation
port will be blocked.
• Do not install the equipment in a place like a laboratory where chemical reactions are expected, or in a
place where salt or gases are contained in the air.
• Do not connect/disconnect a power cord or a data cable, while holding the cable. Do not pull, install,
use, or carry the equipment in such a manner that force will be applied to the cables.
• Do not drop or insert any foreign substances, such as clips or pins, into the equipment.
• Do not spill any liquid or spray any chemical-containing liquid over the equipment. If any liquid is
spilled on it, turn off the power, disconnect the power cable and power cord from the plug socket, and
so on, and contact our dealer.
• Do not disassemble or remodel the equipment. Negligence of this may cause fire or electric shock.
• Should water enter inside the equipment by any chance, unplug it and contact our office. Using it in
that condition may result in fire or electric shock.
• Use the equipment only with the specified commercial power supply. Negligence of this may result
in fire, electric shock, or problems.
• Do not damage, break, alter, excessively twist, pull, or bundle the power cord. Avoid placing heavy
objects on, or heating the power cord, as this may lead to damages to the power supply which may
cause a fire, an electric shock, or a malfunction. Contact our office if the power cord is damaged.
• Do not connect/disconnect the power cord with wet hands. It may result in an electric shock or other
problems.
• Do not overload a single electrical outlet, using a table tap or a curren t tap socket. It may result in fire
or electric shock.
• An equipment packing bag must be discarded or kept away from children. A child can suffocate if
the bag is placed over the head.
CITIZEN
iDP3550/3551 User’s Manual
PRECAUTIONS FOR INSTALLATION
• Do not use or store the equipment in a place exposed to fire, moisture, or direct sunlight, or in a place
near a heater or a thermal device where the prescribed operating temperature and humidity are not met,
or in a place exposed to much oil, iron powder, or dust. The equipment may become out of order,
emit smoke, or catch fire.
• Do not install the equipment in a place like a laboratory where chemical reactions are expected, or in a
place where salt or gases are contained in the air. There is a danger of fire or electric shock.
• Do not put any object on the printer. It may cause trouble.
• Do not use the equipment near a radio or TV receiver. Do not share the power from a plug socket a
radio or TV receiver is connected to. It may cause a reception problem.
• Use the equipment only at the specified voltage and frequency. Otherwise, it may emit smoke and
catch fire or cause other problems.
• Confirm that a plug socket used for connection has sufficient capacity.
• Do not overload a single electrical outlet in connecting the power cable. It may result in the cable
catching fire or a power outage. Also, do not stamp or put any object on the cable.
• Never connect a grounding cable to a gas pipe. There is a danger of explosion. When connecting or
disconnecting the grounding cable, be sure to disconnect the power plug from the plug socket.
• When connecting/disconnecting the cables, be sure to turn off the power first, including the connected
side, and then connect/disconnect them, holding a plug and a connector. Do not pull or carry the
equipment with a load applied to the cable.
• Connect a connector cable securely. If a reverse-polarity connection is made, internal elements may
be broken or a mating device may be adversely affected.
• Use a shielding wire or twisted pair wire for a signal line, in order to minimize noise effect. Avoid
connecting to a device that is likely to generate noise.
• When a drawer kick connector is provided, do not connect any device other than the prescribed
solenoid specifications. Negligence of this could cause trouble.
• Use the equipment in an environment where there is a plug socket near the main body and you can
easily disconnect the power plug from it, to shut off the power.
• When the equipment will not be used for a long period of time, unplug it.
• When transporting the equipment, remove the rolled paper from it.
• Install the equipment on a flat, stable desk in a well-ventilated place free from vibrations. (Do not
block the ventilation port.)
CITIZEN
iDP3550/3551 User’s Manual
PRECAUTIONS FOR HANDLING
Do not handle the equipment in the following manners, because problems may result.
• Do not print when there is no recording paper or ink ribbon set in the equipment.
The print head may
be damaged
• Be careful not to drop foreign substances, such as clips, pins, and screws, into the main body.
• Do not spill any liquid or spray any chemical-containing liquid over the equipment.
• Do not stamp on, drop, hit, or give a strong shock to the equipment.
• Never use a pointed object, such as a pen, to operate the operation panel.
• Do not use Scotch tape to fasten paper together for continuous use.
• Never pull the set paper forcibly.
When opening/closing the printer cover, take care that the paper
will not be caught.
To Prevent Injury and Spreading of Damage
• Do not touch the printing part of the print head.
• When turning on the power, do not touch the moving parts, such as a cutter and gear inside the main
body, or electric parts.
• Be careful to avoid bodily injure or damaging other objects with an edge of sheet metal.
• Should any error occur while operating the equipment, stop it immediately and disconnect the power
plug from the plug socket.
• Should a problem occur, leave solving it to our serviceman.
Do not disassemble the equipment on
your own.
• When opening/closing the cover, and so on, be careful not to catch your hand or finger on the
equipment.
CITIZEN
iDP3550/3551 User’s Manual
DAILY MAINTENANCE
• Prior to starting maintenance work, be sure to turn off the main body.
• Use a dry soft cloth to wipe off stains and dust from the surfaces of the main body case.
soiling, dip the cloth in water and wring it, for wiping off the soil.
For severe
Never use organic solvents, such
as alcohol, thinner, trichlene, benzene, ketone, or chemical dusters.
• If the equipment is contaminated with paper powder, use a soft brush to clean it.
CITIZEN
iDP3550/3551 User’s Manual
CONTENTS
1. OUTLINE .............................................................................................................................................................. 1
1.1
Features ......................................................................................................................................................... 1
1.2
Unpacking ..................................................................................................................................................... 1
2. BASIC SPECIFICATIONS.................................................................................................................................. 2
2.1
Model Classifications..................................................................................................................................... 2
2.2
Basic Specifications ....................................................................................................................................... 3
2.3
Paper Specifications....................................................................................................................................... 5
2.3.1
Recommended Paper........................................................................................................................... 5
2.3.2
Printing Position.................................................................................................................................. 6
2.3.3
Cutter Layout ...................................................................................................................................... 6
3. OUTER APPEARANCE AND COMPONENT PARTS.................................................................................... 7
3.1
iDP3550 ........................................................................................................................................................ 7
3.2
iDP3551 ........................................................................................................................................................ 8
4. OPERATION....................................................................................................................................................... 10
4.1
Detaching/Attaching the Printer Cover ..........................................................................................................10
4.2
Connecting the Interface Cable......................................................................................................................10
4.3
Connecting the Drawer Kick-Out Connector..................................................................................................11
4.4
Opening/Closing the Auto Cutter (iDP3551)..................................................................................................11
4.5
Setting the Ribbon Cassette...........................................................................................................................12
4.6
Inserting the Paper ........................................................................................................................................13
4.7
Attaching the Rear Cover ..............................................................................................................................16
4.8
Attaching the Stacker (iDP3550P) .................................................................................................................16
4.9
How to Remove Remaining Paper Roll .........................................................................................................17
4.10
Removing Paper Jam.....................................................................................................................................18
4.11
Unlocking the Cutter (iDP3551) ....................................................................................................................18
4.12
Operation Panel and Display of Error ............................................................................................................19
4.13
Print Duty.....................................................................................................................................................21
5. DIP SWITCH SETTING.................................................................................................................................... 22
5.1
Location of DIP Switch................................................................................................................................ 22
5.2
DIP Switches Setting .................................................................................................................................... 23
CITIZEN
iDP3550/3551 User’s Manual
6. PRESET JUMPER SETTING ........................................................................................................................... 25
6.1
Location of Preset Jumper ............................................................................................................................ 25
6.2
Preset Jumper Table ..................................................................................................................................... 25
7. MODE SETTING METHOD ............................................................................................................................ 26
8. INPUT BUFFER BACKUP FUNCTION ......................................................................................................... 27
8.1
Buffer Size................................................................................................................................................... 27
8.2
Input Buffer Backup..................................................................................................................................... 27
8.3
Clearing the Input Buffer.............................................................................................................................. 27
9. PARALLEL INTERFACE ................................................................................................................................. 28
9.1
Specifications .............................................................................................................................................. 28
9.2
Connector's Pin Configuration...................................................................................................................... 28
9.3
Input and Output Signals.............................................................................................................................. 29
9.3.1
Input and Output Signals ................................................................................................................... 29
9.3.2
Electrical Characteristics ................................................................................................................... 30
9.3.3
Timing Chart..................................................................................................................................... 31
9.3.4
Data Receiving Control ..................................................................................................................... 31
10. SERIAL INTERFACE ...................................................................................................................................... 32
10.1
Specifications .............................................................................................................................................. 32
10.2
Connector's Pin Configuration...................................................................................................................... 33
10.3
Input and Output Signals.............................................................................................................................. 34
10.3.1 Input and Output Signals ................................................................................................................... 34
10.3.2 Data Configuration............................................................................................................................ 36
10.3.3 Error Detection.................................................................................................................................. 37
10.3.4 Data Receiving Control ..................................................................................................................... 37
10.3.5 Buffering........................................................................................................................................... 37
10.3.6 Electrical Characteristics ................................................................................................................... 38
11. DRAWER KICK-OUT CONNECTOR ........................................................................................................... 39
11.1
Specifications of Drawer Kick-Out Connector .............................................................................................. 39
11.2
Connector's Pin Configuration...................................................................................................................... 39
11.3
Drive Circuit................................................................................................................................................ 39
CITIZEN
iDP3550/3551 User’s Manual
12. WINDER CONNECTOR ................................................................................................................................. 40
12.1
Specifications of Winder Connector ............................................................................................................. 40
12.2
Connector's Pin Configuration...................................................................................................................... 40
12.3
Drive Circuit................................................................................................................................................ 40
13. MAINTENANCE AND SERVICE .................................................................................................................. 41
14. PRINT CONTROL FUNCTIONS .................................................................................................................... 42
14.1
14.2
CBM Mode.................................................................................................................................................. 42
14.1.1
Command List .................................................................................................................................. 42
14.1.2
Description of Items.......................................................................................................................... 43
Star Mode.................................................................................................................................................... 63
14.2.1
14.3
Command List .................................................................................................................................. 63
ESC/POS Mode ........................................................................................................................................... 92
14.3.1
Command List .................................................................................................................................. 92
15. CHARACTER CODES TABLE......................................................................................................................114
15.1
CBM (Japanese)..........................................................................................................................................114
15.2
CBM (International)....................................................................................................................................115
15.3
Star (Japanese)............................................................................................................................................116
15.4
Star (International)......................................................................................................................................117
15.5
Codepage PC437 (USA,European Standard)................................................................................................118
15.6
Codepage Katakana (Japanese)....................................................................................................................119
15.7
Codepage PC850 (Multilingual) ................................................................................................................. 120
15.8
Codepage PC860 (Portuguese) ................................................................................................................... 121
15.9
Codepage PC863 (Canadian-French).......................................................................................................... 122
15.10 Codepage PC865 (Nordic).......................................................................................................................... 123
15.11 Codepage PC852 (Eastern Europe)............................................................................................................. 124
15.12 Codepage PC866 (Russian) ........................................................................................................................ 125
15.13 Codepage PC857 (Turkish) ........................................................................................................................ 126
15.14 Windows Codepage ................................................................................................................................... 127
15.15 International Character Codes Table ........................................................................................................... 128
APPENDIX 1.
BLOCK DIAGRAM ................................................................................................................. 129
APPENDIX 2.
OUTLINE DRAWING for iDP3550 ........................................................................................ 130
APPENDIX 3.
OUTLINE DRAWING for iDP3551 ........................................................................................ 131
CITIZEN
iDP3550/3551 User’s Manual
<<< German >>>
4. BETRIEB ........................................................................................................................................................... 139
4.1
Druckerabdeckung Aufsetzen, Entfernen .................................................................................................... 139
4.2
Anschluß des Schnittstellenkabels .............................................................................................................. 139
4.3
Anschluß des Schubladenausschubsteckers................................................................................................. 140
4.4
Öffnen/Schließen des automatischen Schneidemechanismus (iDP3551) ...................................................... 140
4.5
Einlegen der Farbbandkassette ................................................................................................................... 141
4.6
Einlegen des Papiers .................................................................................................................................. 142
4.7
Hintere Abdeckung des Druckers aufsetzen ................................................................................................ 146
4.8
Hintere Abdeckung des Papierhalte r........................................................................................................... 146
4.9
Herausnehmen der Restpapierrolle ............................................................................................................. 147
4.10
Beseitigung von Papierstaus....................................................................................................................... 148
4.11
Initialisierung des Schneidemechanismus (iDP3551) .................................................................................. 148
4.12
Bedienfeld und Fehleranzeigen................................................................................................................... 149
4.13
Druckvorgang ............................................................................................................................................ 152
5. DIP-SCHALTER-EINSTELLUNG................................................................................................................. 153
5.1
Lage der DIP-Schalter................................................................................................................................ 153
5.2
DIP-Schalter-Einstellungen ........................................................................................................................ 154
6. EINSTELLUNG DER VORWAHL-JUMPERSTECKER............................................................................ 155
6.1
Lage der Vorwahl-Jumperstecker................................................................................................................ 155
6.2
Vorwahl-Jumperstecker-Tabelle.................................................................................................................. 155
7. METHODE FÜR MODUSEINSTELLUNG .................................................................................................. 156
12. WARTUNG UND DIENST............................................................................................................................. 157
Note:
CITIZEN, CITIZEN logo are registered trademark of CITIZEN WATCH CO., LTD.
ESC/POS and EPSON are a trademark and registered trademark of SEIKO EPSON CORP ORATION.
Star is a registered trademark of Star Micronics Corporation.
Windows is a registered trademark of Microso ft Corporation.
CITIZEN
iDP3550/3551 User’s Manual
1.
OUTLINE
This is a small-size dot impact printer developed for various data communication terminals, POS terminals,
kitchen-use printers, and so on.
Its abundant built-in features allow you to widely use this printer for different applications.
Prior to using it,
read and understand this manual thoroughly.
1.1
Features
(1) Small size, light weight, and low price
(2) High-speed print (Bi-directional)
(3) Red and black print
(4) Very easy paper loading by the auto loading function
(5) Paper end and paper near end detecting function (iDP3550F / iDP3551)
(6) Built-in auto cutter (AC-134) (iDP3551)
(7) Built-in power supply
1.2
Unpacking
(1) When unpacking the printer, confirm that the following parts are provided.
• Printer body
----- 1 unit
• Cassette ribbon
----- 1 piece
• Sample paper roll
----- 1 roll (Friction type only)
• User's manual
----- 1 copy
CAUTION :
• Install the printer on a flat and stable desk.
• Do not install the printer near a heater or in a place exposed to direct sunlight.
• Do not use the printer in a high-temperature, high-humidity, and contaminated environment.
• Do not allow dew condensation on the printer.
If dew is condensed on it, leave the power
turned off until dew condensation is gone.
BTW BE 0415.638.961
Rek: 230-0026460-96
info@vanmechelen.be
www.vanmechelen.be
Patersstraat 106-108
2300 Turnhout
Tel:014/42.55.99
Fax: 014/42.32.64
1
CITIZEN
iDP3550/3551 User’s Manual
2.
2.1
BASIC SPECIFICATIONS
Model Classifications
The printer model is classified by the following designation method.
iDP3550
-
F
40
R F
120
C
Type
C: Character Type
(DP-650 Printer Mechanism)
(DP-652 Printer Mechanism)
(DP-654 Printer Mechanism)
G: Graphic Type
(DP-657 Printer Mechanism)
Supply Voltage
120: For 120 V AC
230: For 230 V AC
Character Set
F: International
Interface
• CBM Mode
R: Serial (RS-232C)
P: Parallel (CENTRONICS Compliant)
• Star Mode
S: Serial (RS-232C)
C: Parallel (CENTRONICS Compliant)
• ESC/POS Mode
T: Serial (RS-232C)
I: Parallel (CENTRONICS Compliant)
Column Capacity
23: 23 columns / 230 dots (DP-650)
28: 28 columns / 280 dots (DP-652)
40: 40 columns / 360 dots (DP-654)
40: 40 columns / 400 dots (DP-657)
Paper Feed System
F: Friction
P: Pin tractor (Sprocket)
(iDP3550 only)
Model Name
• iDP3550 Standard Model
• iDP3551 With Auto Cutter
2
CITIZEN
iDP3550/3551 User’s Manual
2.2
Basic Specifications
Model
Item
Printer mechanism
Print method
Print width
And Print columns
Print head
Print speed
Character size
Character types
Line spacing
Paper size
Ink ribbon
Interface
Command system
Print function
Input buffer
Buffer backup function
Drawer function
Auto loading function
Paper end detection
Paper near end detection
Auto cutter
iDP3550-F*RF/PF
iDP3551-F*RF/PF
iDP3550-P*RF/PF
iDP3550-F*SF/CF
iDP3551-F*SF/CF
iDP3550-P*SF/CF
iDP3550-F*TF/IF
iDP3551-F*TF/IF
iDP3550-P*TF/IF
Character type
: DP-650 series / DP-652 series / DP-654 series (CITIZEN)
Graphic type
: DP-657series (CITIZEN)
Serial dot impact method (Bidirectional print)
2-pass graphic (Unidirectional print)
DP-650 series: 57.3 mm / 23 columns
DP-652 series: 58.2 mm / 28 columns
DP-654 series: 63.6 mm / 40 columns
DP-657 series: 58.7 mm / 40 columns
9 pins
DP-650 series: Approx. 3.6 lines/second
DP-652 series: Approx. 3.6 lines/second
DP-654 series: Approx. 3.6 lines/second
DP-657 series: Approx. 3 lines/second
DP-650 series:
1.80 mm(W) × 2.4 mm(H) (7 dots)
1.80 mm(W) × 3.1 mm(H) (9 dots)
DP-652 series:
1.50 mm(W) × 2.4 mm(H) (7 dots)
1.50 mm(W) × 3.1 mm(H) (9 dots)
DP-654 series:
1.36 mm(W) × 2.4 mm(H) (7 dots)
1.36 mm(W) × 3.1 mm(H) (9 dots)
DP-657 series:
1.36 mm(W) × 2.4 mm(H) (7 dots)
1.36 mm(W) × 3.1 mm(H) (9 dots)
Alphanumeric, Katakana, International characters, Code pages
PC850, PC860, PC863, PC865, PC852, PC866, PC857, Windows code
DP-650, DP-652, DP-654 series: 4.23 mm (1/6 inch)
DP-657 series: 2.82mm (1/9 inch)
Fan-Fold paper:
Ordinary paper and non-carbon paper:
Width: 3 to 3.5 inches
76 +/- 0.5 mm(W) × φ83 mm(OD)
( 76 to 89 mm)
Special purpose ribbon cartridge:
Red/black or single color (Black or Purple)
Serial(RS-232C), Parallel(CENTRONICS compliant)
CBM mode, Star mode, ESC/POS mode
The user can select the mode with the DIP switch and preset jumpers.
On-line, self-test, and hex. Dump print function
(Provided by operating the p ower, LF, and SEL switches.)
6 KB or 256 bytes (Selectable with the DIP switch)
Within 24 hours (After 10 minutes or more of printer operation)
2-drawer, 1-drawer switch
Automatically feeds the paper by several lines
None
When it is inserted.
Stops printing when the paper has run out.
None
Stops printing when the paper is running out. (Settable
None
with a command)
AC-134 (Capable of
None
None
partial and full cut)
3
CITIZEN
iDP3550/3551 User’s Manual
Model
Item
Winder
Supply voltage
Power consumption
Weight
Outer dimensions
(W) × (D) × (H)
Operating temperature and
humidity
Storage temperature and
humidity
Reliability
EMI standard
Safety standard
iDP3550-F*RF/PF
iDP3551-F*RF/PF
iDP3550-P*RF/PF
iDP3550-F*SF/CF
iDP3551-F*SF/CF
iDP3550-P*SF/CF
iDP3550-F*TF/IF
iDP3551-F*TF/IF
iDP3550-P*TF/IF
Special purpose winder AW-3-E (Option) that will be placed separately.
120 V AC +/- 10 %, 50/60 Hz
230 V AC +/- 10 %, 50/60 Hz
Not printing: Approx. 10 W, Printing: Approx. 30 W
Approx. 2.8 kg
Approx. 3 kg
Approx. 2.8 kg
160 × 212 × 173 mm
160 × 212 × 194 mm
160 × 212 × 173 mm
0 to 40°C, 35 to 85 % RH (No dew condensation)
-20 to 60 °C, 10 to 90 % RH (No dew condensation)
Print head: 80,000,000 characters
Mechanism: MCBF 4,000,000 lines
Auto cutter: 300,000 cuts (iDP3551)
(With single-sheet recommended paper and 25°C temperature)
U.S.A.: FCC Class-A
Europe: EN55022 Class-B CE Marking
U.S.A., Canada: UL, c-UL Europe: TUV, GS
4
CITIZEN
iDP3550/3551 User’s Manual
2.3
Paper Specifications
2.3.1
Recommended Paper
iDP3550F / iDP3551
• Type
: Normal paper roll and non-carbon paper roll
• Paper width
: 76 +/- 0.5 mm
• Paper thickness
: Single-sheet paper --- 45 to 55 kg/1,000 sheets/1,091 × 788 mm
Copying paper ---
Non-carbon paper or 1 original + 1 copy
34 kg for each paper
Total thickness 0.2 mm or less
• Roll diameter
: φ83 mm or less (φ80 mm or less for the copying paper)
• Core
: φ12 mm (Inner Diameter), φ18 mm (Outer Diameter)
iDP3550P
• Type
: Normal Fan-Fold paper and non-carbon Fan-Fold paper
• Paper width
: 76 to 89 mm (3 to 3.5 inches)
• Paper thickness
: Single-sheet paper --- 45 to 55 kg/1,000 sheets/1,091 × 788 mm
Copying paper ---
Non-carbon paper or 1 original + 2 copy
34 kg for each paper
Total thickness 0.2 mm or less
5
CITIZEN
iDP3550/3551 User’s Manual
2.3.2
Printing Position
Mechanism
DP-650
DP-652
DP-654
DP-657
A
57.3
58.2
63.6
58.7
B
9.3
8.9
6.2
8.6
‘
B
15.8
15.4
12.7
15.1
‘
C
C
D
6.35
6.35
or
5.0
12.7
(mm)
2.3.3
Cutter Layout
iDP3550 tear bar position
: Approx. 28 mm
iDP3551 auto cutter cutting position
: Approx. 19 mm
Cutting position
iDP3550
iDP3551
: Approx. 28 mm
: Approx. 19 mm
Center of the first printing line
6
CITIZEN
iDP3550/3551 User’s Manual
3.
3.1
OUTER APPEARANCE AND COMPONENT PARTS
iDP3550
Manual Cutter
(4)SEL/ERROR Lamp
(9)Printer Cover
(3)POWER Lamp
(10)Knob
(iDP3550P only)
Upper Cover
Bottom Cover
(6)SEL Switch
(5)LF Switch
(11)Rear Cover
(iDP3550F / iDP3551)
Paper Holder
(2)Power Switch
(13)Stacker (Option)
(iDP3551P)
(7)Interface Connector
(8)External Output Connecter
(Drawer Kick-Out Connector)
(1)Power Cord Plug
(12)Winder Connector
7
CITIZEN
iDP3550/3551 User’s Manual
3.2
iDP3551
(4)SEL/ERROR Lamp
(9)Printer Cover
(3)POWER Lamp
Upper Cover
(6)SEL Switch
Bottom Cover
(5)LF Switch
Paper Holder
(2)Power Switch
(11)Rear Cover
(1)Power Cord Plug
(7)Interface Connector
(12)Winder Connector
(8)External Output Connecter
(Drawer Kick-Out Connector)
8
CITIZEN
iDP3550/3551 User’s Manual
(1) Power cord plug
Insert it into an AC outlet of the rated voltage.
(2) Power switch
When the power switch is turned on, the electric power is supplied to the printer and the initializing
operation is started.
(3) POWER lamp (Green LED)
Lights when the power switch is turned on and goes out when it i s turned off.
(4) SEL/ERROR lamp(Green LED)
On:
Online
Off:
Offline
Flashing (approx. once every second): Out of paper
Flashing (approx. twice every second):
Mechanical error
(Buzzer sounds once.)
(5) LF switch
Feeds the paper.
(6) SEL switch
Changes between select and deselect status. Also used to cancel the alarm status. (In ESC/POS mode,
only used to cancel the alarm.)
(7) Interface connector
Uses a cables to connect to a personal computer. Check that the computer and printer are turned off
when connecting.
(8) External output connector
Drawer control connector.
(9) Printer cover
Detach when changing the ribbon cassette.
(10)Manual paper feed knob
Use to adjust the paper position (iDP3550P).
(11) Rear cover
Paper roll dust cover. (iDP3550F / iDP3551)
(12) Winder connector
For an optional winder (AW-3).
(13)Stacker (Option)
Basket for Fan-Fold paper. (iDP3550P)
9
CITIZEN
iDP3550/3551 User’s Manual
4.
4.1
OPERATION
Detaching/Attaching the Printer Cover
1. Use both hands to hold the projections on each side of the printer cover and lift the printer cover in the
direction shown by the arrow to detach it.
2. When attaching the printer cover, place the hooked part at the front in the appropriate part of the printer
and lower the printer cover.
Projection
4.2
Connecting the Interface Cable
1. Turn off the power. (Mating side included)
2. Check the top and bottom of the cable terminals, and connect to the interface connector.
3. Secure the cable terminals.
Serial interface
: Tighten screws to secure.
Parallel interface
: Turn clamps to secure.
4. Connect the interface cable to the computer.
Serial Interface Connector
Serial Interface Cable
Parallel Interface Connector
Clamp
Parallel Interface Cable
10
CITIZEN
iDP3550/3551 User’s Manual
4.3
Connecting the Drawer Kick-Out Connector
1. Turn off the power.
2. Check the top and bottom of the drawer kick-out cable connector and connect it to the drawer kick-out
connector located at the lower section of the printer.
3. Screw the grounding cable of the drawer to the grounding terminal located at the lower section of the
printer.
CAUTION: • Connect only the prescribed drawer (Solenoid) to the drawer kick -out connector.
Drawer Kick-Out Connector
Drawer Kick-Out Cable Connector
Earth
Terminal
4.4
Opening/Closing the Auto Cutter (iDP3551)
1. Hold the auto cutter and, while pushing the lock lever, turn the auto cutter over to open it.
2. When closing the auto cutter, be sure that it is securely locked by the lock lever.
CAUTION: • When closing the auto cutter, do so gently not to give a shock.
Auto Cutter
Lock Lever
11
CITIZEN
iDP3550/3551 User’s Manual
4.5
Setting the Ribbon Cassette
1. Be sure that the power switch is turned off.
2. Detach the printer cover.
3. Open the auto cutter. (iDP3551)
4. If the ribbon is slackened, turn the knob in the direction shown by the arrow to give the tension before
placing it in the printer.
5. Push teh locking claws into the holder of the printer as you place the ribbon between the print head and
ribbon guide.
A click sound will be heard.
6. Turn the knob of the ribbon cassette in the direction shown by the arrow to eliminate any slackness of
the ribbon.
7. To remove the ribbon cassette, lift it while tilting the locking claws inwards.
The locking claws are
located at both sides.
8. Close the auto cutter. (iDP3551)
9. Attach the printer cover.
CAUTION: • When closing the auto cutter, do so gently not to give a shock.
:Place the ribbon here.
Print Head
Ribbon Cassette
Ribbon
Knob
Locking Claw
12
CITIZEN
iDP3550/3551 User’s Manual
4.6
Inserting the Paper
4.6.1 Using paper roll (iDP3550F / iDP3551)
1. Cut the end of the paper roll at close to a right angle.
CAUTION :
• Be sure to use the specified paper roll.
• Use of unspecified paper may adversely affect print quality, printer service life, and so on.
• Do not insert a frayed or bent end of paper into the printer.
2. Check the winding direction of the paper roll. (See the figure of the below.)
3. Hold the paper holder open and insert the paper roll so that it is securely supported by the paper holder.
4. Turn on the printer.
5. Insert the end of the paper roll straight into the paper inlet slot (Indicated by the arrow).
6. The paper is automatically fed in and comes out the paper outlet of the printer (Paper outlet of the auto
cutter for the iDP3551).
You can cut the surplus paper using the tear bar.
(iDP3550F)
CAUTION : • If the paper is slack, rewind it, to remove the slack.
• While printing, do not hold the paper.
This can cause a paper jam.
• When closing the auto cutter, do so gently not to give a shock.
Paper Inlet Slot
Paper Holder
13
CITIZEN
iDP3550/3551 User’s Manual
4 .6.2 Using Fan-Fold paper (iDP3550P)
Setting the initial
1. Remove the printer cover.
2. Set the imprint face of the paper downward and put into the paper entrance.
3. If necessary to adjust the sprocket-wheel’s position, free the wheels using the lever
on both sides. Slide them to the appropriate position, and lock them back.
(See the left diagram of the below.)
4. Hook some of the paper’s perforations on the sprockets and forward the paper into
the printer mechanism by pulling and turning the paper -feed knob until the paper ’s
tip reaches the platen. ( See the right diagram of the below.)
General using
1. Set the imprint face of the paper downward and put into the paper entrance.
2. Hook some of the paper's perforations on the sprockets and forward the paper into
the printer mechanism by pulling and turning the paper -feed knob.
Platen
Knob
LOCK
Sprocket
(Pin tractor)
FREE
Knob
14
CITIZEN
iDP3550/3551 User’s Manual
Handling of the fan-fold paper
1. iDP3550P can use the fan-fold paper of the 3 to 3.5 inches.
2. Change the position of the sprocket (pin tractor) as necessary when feeding the paper.
3. After feeding the paper, align it with the mark on the platen.
CAUTION :
• Be sure to use the specified fan-fold paper.
• Use of unspecified paper may adversely affect print quality, printer service life, and so on.
4. The sprocket holes on 3-inch fan-fold paper may be positioned 6.35 mm or 5 mm from the edge of the
paper. Note the following when feeding 3-inch fan-fold paper.
CAUTION :
• 6.35mm
When feeding paper with sprocket holes positioned 6.35 mm from the edge, align the
edges with the paper guides on the printer. Because the edges of the printing area are
close to the sprocket holes, it is important to make sure the paper is positioned correctly.
•
5mm
When feeding paper with sprocket holes positioned 5 mm from the edge, align the pins in
the sprockets with the positions of the paper holes and then turn the knob. Note that in this
case there is a gap between the edges of the paper and the paper guides on the printer.
5. Use fan-fold paper with round sprocket holes.
6. When using multiple page fan-fold paper, the perforated line on the margin should be within 5mm of the
side of the paper.
BTW BE 0415.638.961
Rek: 230-0026460-96
info@vanmechelen.be
www.vanmechelen.be
Patersstraat 106-108
2300 Turnhout
Tel:014/42.55.99
Fax: 014/42.32.64
15
CITIZEN
iDP3550/3551 User’s Manual
4.7
Attaching the Rear Cover (iDP3550F / iDP3551)
Insert the claws of the rear cover into the square holes at the back of the printer, and move the rear cover in
the direction of the arrow to close it.
Square Hole
Rear Cover
4.8
Attaching the Stacker (iDP3550P)
1) Stacker capacity
The stacker can accommodate fan-fold paper with a length of up to 89mm (3.5 inches) and a thickness of
up to 40 mm.
2) Attaching the Stacker
Insert the hooks of the stacker into the square holes at the back of the printer, then lower the stacker in
the direction indicated by the arrow.
Square Hole
Stacker
16
CITIZEN
iDP3550/3551 User’s Manual
4.9
How to Remove Remaining Paper
4.9.1 Paper roll
1. Detach the printer cover.
2. Open the auto cutter. (iDP3551)
3. Remove the paper by pulling it in the direction in which it is normally guided.
4. Close the auto cutter. (iDP3551)
5. Attach the printer cover.
CAUTION : • When removing the paper, do not pull the paper from the paper inlet. (Do not remove the
paper in the reverseed direction.)
• When closing the auto cutter, do so gently not to give a shock.
4.9.2 Fan-Fold paper
1. Detach the printer cover.
2. While turning the knob in the direction indicated by the arrow, pull out the fan-fold paper in the
direction shown in the drawing.
17
CITIZEN
iDP3550/3551 User’s Manual
4.10
Removing Paper Jam
1. Detach the printer cover.
2. Cut off the paper near the paper inlet slot.
3. Remove the paper by pulling it in the direction in which it is normally guided.
4. Eliminate completely the paper remaining in the paper route.
5. Attach the printer cover.
CAUTION : • When removing the paper, do not pull from the paper inlet. (Do not remove the
paper in the
reverse direction.)
• When closing the auto cutter, do so gently not to give a shock.
4.11
Unlocking the Cutter (iDP3551)
1. Detach the printer cover.
2. Press the LF switch.
The auto cutter is initialized to return its blade and clear an alarm.
3. If the paper is jamming, eliminate the jamming paper completely, seeing "4.10 Removing Paper Jam."
4. If the alarm still cannot be cleared, turn off the power and open the a uto cutter.
5. You can see an emergency knob through a small hole in the back of the auto cutter.
screwdriver, etc., turn the knob in the arrow-indicated direction to return the blade.
Using tweezers,
If there is a paper
jam or paper refuse, eliminate it completely.
6. Attach the printer cover.
CAUTION:
• When pulling out the paper(Forward/Reverse direction), be sure to operate the paper free lever.
•
When closing the auto cutter, do so gently not to give a shock.
Auto Cutter
Emergency Knob
18
CITIZEN
iDP3550/3551 User’s Manual
4.12
Operation Panel and Display of Error
1. POWER lamp (Green)
This lamp is illuminated when the power is supplied.
2. ERROR lamp (Green)
This lamp is illuminated or blinks to indicate each error.
Error Indication
Mechanical Error
SEL/ERROR Lamp
Quick blinking
Paper End
Blinks.
(Once a second)
Paper Near End
Blinks.
(Once a second)
Cutter Motor
(iDP3551 only)
Lock
Quick blinking
(Twice a second)
Buzzer
Sounds continuously for
approx. 1 second
Repeats a short 4-time
sound twice at
intervals of 0.5 second.
Repeats a short 4-time
sound twice at
intervals of 0.5 second.
Sounds continuously
for approx. 1 second.
Resetting Method
Reset the Power
switch.
Set a new paper roll.
Set a new paper roll.
Eliminate a paper
jam.
Mechanical Error
: If the printer mechanism has a greater load due to a paper jam, etc., the buzzer
will sound and the SEL/ERROR lamp will blink to stop the printer mechanism.
Paper End
(iDP3550F ,
iDP3551)
: If the printer has run out of paper, the paper sensor in the paper path near the
print head will detect the end of the paper roll, turn on the buzzer, and blink the
SEL/ERROR lamp to stop the printer mechanism. If the paper is inserted
into the paper path, the paper will be loaded. (See 4.6 Inserting the Paper)
Paper Near End
: If the paper is running out, the paper near end sensor will be activated to turn
on the buzzer and make the SEL/ERROR lamp blink. Even after the paper
near end is detected, a command can be used to print by the specified number
of lines. (See a description on the command for setting the number of print
lines after paper near end detection)
(iDP3550F ,
iDP3551)
Cutter Motor Lock
(iDP3551 only)
: If the cutter position detection sensor in the cutter unit is left turned on or off
for approx. 1 second while the cutter motor is running, cutter operation and
printing will be suspended, determining it to be motor lock.
Backup Data Clear
: When the power is turned on, depending on the SEL switch operation, the
backup data in the input buffer will be cleared according to the flowchart on
the next page.
To clear the input buffer, turn on the power while pressing the SEL switch.
The following messages will be printed.
“Clear Data in Buffer”
“Cleared Data in Buffer”
To print the data in the input buffer, simply turn the power on.
message is printed and the data in the input buffer is printed.
The following
“Power Down(Data in Buffer)”
Test Print
When the power is turned on while the LF switch is pressed, a test print is
carried out.
19
CITIZEN
iDP3550/3551 User’s Manual
Dump Mode
When the power is turned on while the LF and SEL switches are pressed, the
printer enters dump mode and prints the following message.
“=== Hexadecimal Dump ===”
Power-on
SEL SW ?
•SEL/ERROR lamp blinks
intervals of 0.25 sec.
•Buzzer sounds for 1 sec.
ON
OFF
Buffer Data
at
The message "Clear Data
in Buffer" is printed in
enlarged red characters.
Then, 5 lines are rapidly
fed.
YES
NO
1 sec. passed
YES
NO
OFF
SEL SW ?
ON
Buffer Data
The input buffer is cleared and
the message “Cleared Input
Buffer” is printed. Then, 5
lines
are
rapidly
fed.
SEL/ERROR lamp lights up.
NO
YES
The message "Power Down (Data
in Buffer)" is printed in red,
followed by the contents of the
After printing, SEL/
buffer.
ERROR lamp lights up.
Waits for data input
20
CITIZEN
iDP3550/3551 User’s Manual
4.13
Print Duty
As the printing head mounted onto this printer is not equipped with a head temperature detection sensor
(Thermistor), the printer protects the printing head against temperature through software.
The printer calculates the number of print dots and prints as follows, depending on whether the number
of printing dots per line is over or within 648.
1)Within 648 dots
Prints in both directions
2)Over 648 dots
Prints in a single direction
21
CITIZEN
iDP3550/3551 User’s Manual
5.
5.1
DIP SWITCH SETTING
Location of DIP Switch
1. Turn off the power.
2. Remove the printer cover.
3. The DIP switch can be found at the location shown in the figure below. (Only DSW2 is available for the
serial interface.)
22
CITIZEN
iDP3550/3551 User’s Manual
5.2
DIP Switches Setting
1) DIP Switch 1
No.
DSW1-1
DSW1-2
DSW1-3
DSW1-4
Function
Auto cutter
International characters
DSW1-5
CBM command
ON
Yes
″
″
OFF
No
Upon Shipment from Factory
ON *1
ON *2
ON *2
ON *2
See the Table below
CBM2 mode
CBM1 mode
(iDP3530
(iDP3540
system)
system)
See the Table below
Graphic
Character
6K bytes
256 bytes
OFF *4
DSW1-6
CR mode
DSW1-7
Mechanism type
DSW1-8
Buffer size
DSW1-9
Operation mode
See the table below
DSW1-10
″
*1, *3 : Depends on the type.
*2
: Depends on the destination.
*4
: Effective only when CBM mode is selected with DSW1-9 and -10.
Mode” in “PRINT CONTROL FUNCTIONS.
*5
: With the Graphic type, the DIP switches maked are set to ON.
(Do not change the shipment setting.)
International Character Selection
No.
Country
DSW1-2
OFF
OFF *5
ON
OFF *3
OFF *3
For details see “CBM
Character Code Selection
DSW1-3
DSW1-4
ESC/POS
mode
U.S.A.
ON
ON
ON
Code 437
France
Germany
U.K.
Denmark
Sweden
Italy
Windows
Code
OFF
ON
OFF
ON
OFF
ON
ON
OFF
OFF
ON
ON
OFF
ON
ON
ON
OFF
OFF
OFF
OFF
OFF
OFF
Code 850
″
″
Code 865
″
Code 850
Windows
Code
CBM mode
Star mode
CBM
(International)
Code 850
″
″
Code 865
″
Code 850
Windows
Code
Star
(International)
Code 850
″
″
Code 865
″
Code 850
Windows
Code
See the “International Character Codes Table and Character Codes Table”.
CR mode(DSW1-6)
Mode
CBM
Star
ESC/POS
OFF
CR+LF
CR+LF
CR+LF
Operation Mode
ON
CR
Ignored
CR
CBM
ESC/POS
Star
Star Auto cut
23
DSW1-9
OFF
ON
OFF
ON
DSW1-10
OFF
OFF
ON
ON
CITIZEN
iDP3550/3551 User’s Manual
2) DIP Switch 2
No.
DSW2-1
DSW2-2
DSW2-3
DSW2-4
DSW2-5
DSW2-6
DSW2-7
DSW2-8
Function
Bit length
Parity
Odd/Even
Communication mode
Baud rate
ON
8 bits
No
Odd
DTR/DSR
″
″
OFF
7 bits
Yes
Even
XON/XOFF
See the table below

Unused

Factory Setting
ON
ON
ON
ON
ON
ON
OFF
OFF
Baud rate
Baud rate
150
300
600
1200
2400
4800
9600
19200
DSW2-5
OFF
OFF
OFF
OFF
ON
ON
ON
ON
DSW2-6
OFF
OFF
ON
ON
OFF
OFF
ON
ON
DSW2-7
OFF
ON
OFF
ON
OFF
ON
OFF
ON
♦ The DIP switch 2 is used only for the serial interface .
24
CITIZEN
iDP3550/3551 User’s Manual
6. PRESET JUMPER SETTING
6.1
Location of Preset Jumper
(1) Turn off the power.
(2) The preset jumper is set at the time of shipment from the factory. If the settings are to be changed, do so by
removing the control board and changing the setting as indicated in the service manual.
The location of the preset jumpers is shown in the figure below.
Serial Interface
6.2
Parallel Interface
Preset Jumper Table
Serial Interface
Mode
Location
SC1-A
SC1-B
SC1-C
SC1-D
SC1-E
SC1-F
SC1-G
SC1-H
CBM
Star
ESC/POS
1-C *
1-C *
1-C
1-C
1-C *
1-C *
1-C *
1-C
2-C
1-C *
2-C
2-C
2-C
2-C
2-C
2-C *
2-C
2-C
*
*
1-C *
1-C *
1-C *
2-C *
CBM
Star
ESC/POS
1-C *
1-C
1-C *
1-C
1-C
1-C
1-C *
1-C
2-C *
2-C
2-C
2-C *
* = Open
1-C * = 1-C or open
2-C * = 2-C or open
Parallel Interface
Mode
Location
SC1-A
SC1-B
SC1-C
SC1-D
* = Open
1-C * = 1-C or open
2-C * = 2-C or open
25
CITIZEN
iDP3550/3551 User’s Manual
7.
MODE SETTING METHOD
This printer has the CBM, Star, and ESC/POS mode.
Any desired mode can be selected and set according
to your need.
(1) Setting method
• See 5 “DIP SWITCH SETTING”.
• Seeing the settings of the DIP switch segments 1-9 and 1-10 and those of the preset jumper, set each
mode.
26
CITIZEN
iDP3550/3551 User’s Manual
8.
8.1
INPUT BUFFER BACKUP FUNCTION
Buffer Size
With the DIP switch, you can set either 6 K bytes or 256 bytes.
DIP switch segment 1-8
ON
→ 6K bytes
OFF → 256 bytes
8.2
Input Buffer Backup
Even if the power is turned off or fails during the printing process, the data in the input buffer will be saved.
If the power is turned on again, the printer will print a power failure mark, "==POWER DOWN==" in red
and reprints the data from the beginning of the line where it left off.
8.3
Clearing the Input Buffer
When you want to clear the data in the input buffer, turn on the power while holding down the SEL switch.
The following messages will be printed to notify that the input buffer is cleared.
“Clear Data in Buffer”
“Cleared Data in Buffer”
If the printer prints the data erroneously at power-on, clear the input buffer as described above, and
then, re-input the data..
27
CITIZEN
iDP3550/3551 User’s Manual
9. PARALLEL INTERFACE
9.1
Specifications
• Data input system
: 8-bit parallel system (DATA1 to DATA8)
• Control signals
: ACK, BUSY, STB, FAULT, SELECT, RESET, COMPULSION
• Applicable connectors
: Printer side
Cable side
9.2
--- 57LE-40360 (Anphenol), or equivalent
--- 57-30360 (Anphenol), or equivalent
Connector's Pin Configuration
Mode
No.
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
CBM
STB
DATA 1
DATA 2
DATA 3
DATA 4
DATA 5
DATA 6
DATA 7
DATA 8
ACK
BUSY
PE(HI-LEVEL)
SELECT
GND
GND
GND
FRAME GND
Vcc
Star
←
←
←
←
←
←
←
←
←
←
←
←
←
←
NC
NC
←
←
Mode
ESC/POS No.
19
←
20
←
21
←
22
←
23
←
24
←
25
←
26
←
27
←
28
←
29
←
30
←
31
←
32
←
33
←
34
←
35
←
36
NC
28
CBM
Star
ESC/POS
TWISTED PAIR GND
↑
↑
↑
↑
↑
↑
↑
↑
↑
↑
↑
RESET
FAULT
NC
COMPULSION
NC
Vcc
←
←
←
←
←
←
←
←
←
←
←
←
←
←
←
←
←
←
←
←
←
←
←
←
←
←
←
←
←
←
←
←
GND
←
Vcc
NC
CITIZEN
iDP3550/3551 User’s Manual
9.3
Input and Output Signals
9.3.1
Input and Output Signals
(1) Input signals to the printer
• DATA
: An 8-bit parallel signal. (Active “High”)
• STB
: A strobe signal to read the 8-bit data. (Active “Low”)
• RESET
: A signal to reset the printer from the outside. (Active “Low”)
(2) Output signals from the printer
• ACK
: An 8-bit data request signal.
A pulse signal output at the end of the BUSY signal.
(Active “Low”)
• BUSY
: A signal to indicate the BUSY status of the printer.
Input new data when at "Low".
(Active “High”)
• FAULT
: A signal turned to "Low" when the printer has an alarm.
At this time, all the
control circuits in the printer stop. (Active “Low”)
• SELECT
: A signal to show whether the printer is selected (On -line) or deselected.
(Active “High”)
• COMPULSION
: A signal to show the status of the drawer switch. ( Active “High”)
• PE
: A signal to show that the paper has run out.
Normal at the "Low" level, but turned
to the "High" level when the paper has run out.
(3) Power related signal
• GND
: Common ground on the circuits
• Vcc
: A +5 V signal.
Connected via a 3.3kΩ resistor. (Factory use only)
29
CITIZEN
iDP3550/3551 User’s Manual
9.3.2
Electrical Characteristics
(1) Input signal level
All the input signals are at the TTL level.
"HIGH" level : 2.0 V at minimum
"LOW" level : 0.8 V at maximum
(2) Output signal level
All the output signals are at the TTL level.
"HIGH" level : 2.4 V at minimum
"LOW" level : 0.4 V at maximum
(3) Input and output conditions
All the input signals are pulled up with a 3.3 k Ω resistor.
[Printer Side]
[Host Side]
Twisted Pair Wire
All the output signals are pulled up with a 3.3kΩ resistor.
[Printer Side]
[Host Side]
Twisted Pair Wire
30
CITIZEN
iDP3550/3551 User’s Manual
9.3.3
Timing Chart
(1) Data input and printing timing
9.3.4
T1, T2, T3
: 0.5 µs MIN
T4
: 270 ns MAX
T5
: 2.3µs TYP
T6
: 500 ms MIN (At power-on)
Data Receiving Control
When the BUSY signal is at "LOW," the printer can receive the data from the host, but when at "HIGH,"
it cannot.
31
CITIZEN
iDP3550/3551 User’s Manual
10. SERIAL INTERFACE
10.1
Specifications
(1) Synchronous system:
Asynchronous
(2) Baud rate: 150, 300, 600, 1200, 2400, 4800, 9600, or 19200 bps (User selectable)
(3) Configuration of one word
• Start bit
: 1 bit
• Data bits
: 7 or 8 bits (User selectable)
• Parity bit
: Odd, even, or none (User selectable)
• Stop bit
: 1 bit or more
(4) Signal polarity
RS-232C
• Mark
= Logic "1" (-3 V to -12 V)
• Space
= Logic "0" (+3 V to +12 V)
(5) Received data (RXD signal)
RS-232C
• Mark
= 1
• Space
= 0
(6) Reception control (DTR signal)
RS-232C
• Mark
: Data transfer disabled
• Space
: Data transfer enabled
32
CITIZEN
iDP3550/3551 User’s Manual
10.2
Connector's Pin Configuration
Mode
No.
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
CBM
Star
ECS/POS
FG
TXD
RXD
←
←
←
←
←
←
←
RTS
DSR
GND
←
PE (HI-LEVEL)
FAULT
RCH
←
GND
FAULT
mTXD
mRXD
←
DTR
←
RESET
Cautions: 1. An RS-232C signal is based on the EIA RS-232C.
2. When the data is not being transferred, the received data should be always maintained as a
mark.
BTW BE 0415.638.961
Rek: 230-0026460-96
info@vanmechelen.be
www.vanmechelen.be
Patersstraat 106-108
2300 Turnhout
Tel:014/42.55.99
Fax: 014/42.32.64
33
CITIZEN
iDP3550/3551 User’s Manual
10.3 Input and Output Signals
10.3.1 Input and Output Signals
(1) RXD
This is a serial received data signal.
When a framing error, overrun error, or parity error occurs,
that data is printed as "?".
(2) DTR
When this signal is Ready, write the data or a command.
error results, ignoring the previous data.
printing.
If written at the time of Busy, an overrun
The data can be written in the input buffer even during
Busy is also issued at the time of power -on, test print, on-line, and reset.
(3) TXD
XON (11H) or XOFF (13H) is sent at XON/XOFF control.
XON (11H) is sent every 3 seconds in
the Star mode.
When a command is received, that requests the printer state and printer status, 1-byte corresponding
data is output.
(4) DSR
When this signal is a space, the data is sent from the printer side.
Note that if this signal is a mark
when a request to send command is executed, the printer will wait until the signal becomes a space.
(5) FAULT
CBM mode
When this signal is Space, a mechanical error has occurred.
Star mode
When this signal is Mark, a mechanical error has occurred.
(6) RESET
A signal to reset the entire printer. (Active Low)
(7) RTS
This signal is turned to Space when the printer is turned on.
34
CITIZEN
iDP3550/3551 User’s Manual
(8) RCH
When the printer is ready to receive, this signal is turned to Space.
This signal line is the same as
DTR.
(9) mTXD
TXD signal for the diode gate.
(10) mRXD
RXD signal for the diode gate.
(11) FG
This is a Frame Ground signal.
(12) GND
This is a common ground on the circuit.
35
CITIZEN
iDP3550/3551 User’s Manual
10.3.2
Data Configuration
t
Mark
b0, b1, b2, • • • •
Space
(1)
(2)
(3)
(1) Start Bit
(2) Data Bit (+ Parity Bit)
(3) Stop Bit (1 or More)
(1) Start bit
After a lapse of 1/2 bit from a mark-to-space fall edge, the state is read again, and if it is a space, it is
recognized as the start bit.
If it is a mark, it is assumed neither the start bit nor an error, and it is
attempted to detect the start bit again.
(2) Data bit + parity bit
The data bit and parity bit are sampled for 1 bit worth of time from the 1/2 start bit.
is assumed the data for the corresponding bit.
The then state
A sequence of the bits are named Bit 0, Bit 1, ...,
parity bit, starting from the one closest to the start bit.
(3) Stop bit
The stop bit is a mark level of 1 bit or more.
If a space is detected in detecting the stop bit, a
framing error results.
36
CITIZEN
iDP3550/3551 User’s Manual
10.3.3
Error Detection
A parity error, framing error, and overrun error are detected.
When an error is detected, that data is
stored in the buffer as "?".
(1) Framing error
This error results when a space is detected in detecting the stop bit.
That data is stored in the buffer
as "?".
(2) Parity error
If a parity check has been specified and an error is detected at the time of parity check, that data is
stored in the buffer as "?".
(3) Overrun error
If an overrun error is detected, that data is stored in the buffer as "?".
10.3.4
Data Receiving Control
When the DTR signal is a space, the data from the host side can be received.
When it is a mark,
however, the data cannot be received.
10.3.5
Buffering
The DTR and TXD signals are available as control signals to transfer the data to the input buffer.
37
CITIZEN
iDP3550/3551 User’s Manual
10.3.6
Electrical Characteristics
(1) RS-232C circuit
Input (RXD, DSR, mRXD)
[Printer Side]
[Host Side]
Mark=(-8V) : Stop bit
RXD
Space=(+8V): Start bit
Equivalent to MAX232
Output (DTR, TXD, mTXD, RCH, RTS, FAULT)
Equivalent to MAX232
Mark=(-8V) : At Busy
Mark=(-8V) : 1
DTR
TXD
Space=(+8V): At Ready
Space=(+8V): 0
(2) Others
• RESET
: A signal to reset the entire printer.
• PE
: A signal to show that the paper has run out.
Normal at the "LOW" level, but turned
to the "HIGH" level when the paper has run out.
• GND
: Signal ground
• FG
: Frame ground
38
CITIZEN
iDP3550/3551 User’s Manual
11. DRAWER KICK-OUT CONNECTOR
11.1
Specifications of Drawer Kick-Out Connector
(1) Drawer kick-out drive signal
Parallel ----- Can be learned at the no. 34 pin of the interface connector
Serial
----- Provided with a command to learn the status in the Star and ESC/POS modes.
(2) Electrical characteristics
1) Drive voltage: 24 V DC
2) Drive current: 0.8 A at maximum (Within 510 ms)
3) Switch signal: Signal level
"L" = 0 to 0.5 V
"H" = 3 to 5 V
11.2
Connector's Pin Configuration
No.
1
2
3
4
5
6
Signal
FG
DRAWER 1
DRSW
VDR
DRAWER 2
GND
Function
Frame Ground
Drawer 1 drive signal
Drawer switch input
Drawer drive power
Drawer 2 drive signal
Common ground on the circuit
Connector used
: 285D-9660J-101(DDK)
Applicable connector
: 285D-1660P-506(DDK) or equivalent
CAUTION : • No output is made while printing.
• The drawers 1 and 2 cannot be driven simultaneously.
• A solenoid used for the drawer should be of 36Ω or more.
An output current should
be kept below 0.8 A. Use beyond this limit cannot be assured.
• This connector cannot be connected to a telephone line.
Do not connect other than
the solenoid.
11.3
Drive Circuit
39
CITIZEN
iDP3550/3551 User’s Manual
12. WINDER CONNECTOR
12.1
Specifications of Winder Connector
(1) Winder drive signal
The winder drive signal is output synchronous with the LF signal.
(2) Electrical characteristics
1) Drive voltage: 24 V DC
2) Drive current: 0.8 A at maximum
12.2
Connector's Pin Configuration
No.
1
2
3
4
Signal
VPX
WD
FG
FG
Function
Winder drive power
Winder drive signal
Frame Ground
Frame Ground
Connector used
: 5045-04A (MOLEX)
Applicable connector
: 5209-04 (MOLEX) or equivalent
CAUTION : • This connector shall be used for Auto Winder AW-3 only.
Do not connect any other device.
12.3
Drive Circuit
40
CITIZEN
iDP3550/3551 User’s Manual
13. MAINTENANCE AND SERVICE
For the information on maintenance and service, please contact our dealer or at the following address.
Northern America
Other Areas
CBM America Corporation
Japan CBM Corporation
Service Center
Information Systems Division
365 Van Ness Way
CBM Bldg., 5-68-10, Nakano
Suit 510
Nakano-ku, Tokyo 164-0001
Torrance, CA 90501, U.S.A
Japan
TEL
+1-310-781-1460
TEL
+81-3-5345-7540
FAX
+1-310-781-9157
FAX
+81-3-5345-7541
41
CITIZEN
iDP3550/3551 User’s Manual
14. PRINT CONTROL FUNCTIONS
14.1 CBM Mode
14.1.1 Command List
1
2
3
Command
FF n
FF
SO (Note)
4
SI (Note)
5
6
7
8
LF
CR
DC 1 (Note)
DC 2 (Note)
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
DC 3 (Note)
CAN
ESC * n1 n2
ESC − n
ESC 1
ESC 2
ESC 3
ESC C n
ESC N n
ESC O
ESC f 1
ESC t n
ESC BEL n1 n2
BEL
FS
SUB
RS
ESC P 0
ESC P 1
ESC R n
ESC & 0 n1 n2
ESC % n
ESC ⁄ n
ESC DC3 n
33
ESC y n
34
ESC DC2 n1 n2
35
36
GS ∗ n1 n2
GS ⁄ m
Function
n-line paper feed (CBM1 mode)
Form feed (CBM2 mode)
Specifying the double width character
(CBM mode)
Canceling the double width character
(CBM mode)
Printing and paper feed
Printing
Initializing the printer (CBM mode)
Specifying/Canceling the Inverted character
(CBM mode)
Specifying the red print (CBM mode)
Canceling the print data
Specifying the bit image mode
Specifying/Canceling the Underline
Specifying 1/9-inch line feed width
Specifying 2/9-inch line feed width
Specifying standard line feed width
Setting the page length
Specifying the perforation skip
Canceling the perforation skip
Form feed (Changing the page)
Selecting the character code table
Setting the external device drive pulse width
Driving command A for Drawer-1
Driving command B for Drawer-1
Driving command for Drawer-2
Buzzer-on
Full cut
Partial cut
Selecting the international character set
Defining the download character set
Specifying/Canceling the download character set
Definition the message
Printing the message
Setting the print lines after paper near end
detection
Deleting the download character, message, bit
image
Defining the download bit image
Printing the download bit image
Code
0CH n
0CH
0EH
0FH
Page
44
44
45
45
0AH
0DH
11H
12H
46
46
46
13H
18H
1BH 2AH n1 n2
1BH 2DH n
1BH 31H
1BH 32H
1BH 33H
1BH 43H n
1BH 4EH n
1BH 4FH
1BH 66H 01H
1BH 74H n
1BH 07H n1 n2
07H
1CH
1AH
1EH
1BH 50H 00H
1BH 50H 01H
1BH 52H n
1BH 26H 00H n1 n2
1BH 25H n
1BH 2FH n
1BH 13H n
48
48
49
49
50
50
50
51
51
51
53
53
54
54
55
55
55
56
56
56
57
58
58
59
1BH 79H n
59
1BH 12H n1 n2
60
1DH 2AH n1 n2
1DH 2FH m
61
62
47
Note: Effective when CBM mode is selected with the DIP switch segments 1-9 and 1-10 and CMB1 (OFF) is
selected with the DIP switch segment 1-5. If CBM2 (ON) is selected with the DIP switch segment 1-5,
the functions of these commands are changed as shown in the table below.
42
CITIZEN
iDP3550/3551 User’s Manual
• CBM2 Mode
Command
Code
SO
0EH
SI
0FH
Command
DC1
DC2
DC3
ESC “C” n
Code
11H
12H
13H
1BH 43H n
14.1.2
8-bit data selected
Specifying the double width
character
Canceling the double width
character
Function
7-bit data selected
Specifying the shift-out side
character
Specifying the shift-in side
character
Function
Page
45
45
Page
47
47
48
52
Selecting the printer
Specifying the red print
Deselecting the printer
Setting the page length
Description of Items
XXXX
ALL
[Function]
Command name
[Code]
A row of command constituent code is represented by a hexadecimal number with < >H,
binary number with < >B, and a decimal number with < >.
[ ]k means a repeat count of
k-times.
[Range]
Describes an argument value (Setting range) for the command.
[Outline]
Describes a command function.
[Caution]
Describes a caution as required.
[Default]
Describes an initial value for the command when accompanied by an argument.
XXX
Shows a command.
43
CITIZEN
iDP3550/3551 User’s Manual
Details
FF n
(CBM1 Mode)
[Function]
n-line paper feed
[Code]
<0C>H n
[Range]
1 ≤ n ≤ 127
[Outline]
This command feeds the paper by n-lines.
You can set n = 1 to 127 lines.
If the print
buffer contains the data, use of this command feeds the paper by n-lines after printing the
data.
Setting n = 0 does not feed the paper.
FF
(CBM2 Mode)
[Function]
Form feed
[Code]
<0C>H
[Outline]
This command searches for the beginning of the next page after printing the data in the print
buffer.
SO
(CBM1 Mode)
[Function]
Specifying the double width character
[Code]
<0E>H
[Outline]
The data following this command is printed doubled in the horizontal direction.
Double
width characters remain valid until the double width character cancel command is entered,
but they are also cancelled after they are printed one line.
Note that the double width
characters take up two ordinary characters worth of width.
44
CITIZEN
iDP3550/3551 User’s Manual
SO
(CBM2 Mode)
[Function]
Specifying the double width character/shift-out side characters
[Code]
<0E>H
[Outline]
The data following this command is printed doubled in the horizontal direction.
Double
width characters remain valid until the double width character cancel command is entered,
but they are also cancelled after they are printed one line.
Note that the double width
characters take up two ordinary characters worth of width.
In the case of a serial interface, if 7-bit data is selected, the shift-out side character is printed.
SI
(CBM1 Mode)
[Function]
Canceling the double width character
[Code]
<0F>H
[Outline]
This command cancels the double width characters set with SO.
The data following this
command are printed in the ordinary character width.
SI
(CBM2 Mode)
[Function]
Canceling the double width character/Specifying the shift-in side characters
[Code]
<0F>H
[Outline]
This command cancels the double width characters set with SO.
The data following this
command are printed in the ordinary character width.
In the case of a serial interface, if 7-bit data is selected, the shift-in side character is printed.
45
CITIZEN
iDP3550/3551 User’s Manual
LF
[Function]
Printing and paper feed
[Code]
<0A>H
[Outline]
If the print buffer contains the data, this command will feed the line after printing.
If not,
the command only feeds the line.
CR
[Function]
Printing
[Code]
<0D>H
[Outline]
This command prints the data.
If the DIP switch segment 1-6 is set to OFF, the printer will
print the data in the print buffer and feed the paper by one line.
If it is set to ON, the print er will print the data in the print buffer and will not feed the paper.
DC1
(CBM1 Mode)
[Function]
Initializing the printer
[Code]
<11>H
[Outline]
This command initializes the printer.
The input buffer is not cleared.
The settings of the DIP switch segments are not re-read.
46
CITIZEN
iDP3550/3551 User’s Manual
DC1
(CBM2 Mode)
[Function]
Selecting the printer
[Code]
<11>H
[Outline]
This command sets the printer in the selecting status.
DC2
(CBM1 Mode)
[Function]
Specifying/Canceling the inverted character
[Code]
<12>H
[Outline]
This command selects/deselects the inverted characters.
beginning of one line.
Otherwise, it is overridden.
Enter this command at the
Erect and inverted characters cannot
be mixed in one line.
DC2
(CBM2 Mode)
[Function]
Specifying the red print
[Code]
<12>H
[Outline]
This command specifies red-color characters.
All the characters in one line are printed in
red by prefixing the print data with this command and sending it to the printer.
When you
want to use red characters, use this command for each line.
47
CITIZEN
iDP3550/3551 User’s Manual
DC3
(CBM1 Mode)
[Function]
Specifying the red print
[Code]
<13>H
[Outline]
This command specifies red-color characters.
All the characters in one line are printed in
red by prefixing the print data with this command and sending it to the printer.
When you
want to use red characters, use this command for each line.
DC3
(CBM2 Mode)
[Function]
Deselecting the printer
[Code]
<13>H
[Outline]
This command sets the printer in the deselecting status in which the printer cannot receive
data.
To set the printer in the selecting status, use DC1.
CAN
[Function]
Canceling the print data
[Code]
<18>H
[Outline]
This command clears the print data in the lines entered prior to this command.
48
CITIZEN
iDP3550/3551 User’s Manual
ESC "∗" n1 n2
[Function]
Specifying the bit image mode
[Code]
<1B>H <2A>H n1 n2
[Range]
1 ≤ n1 + 256 × n2 ≤ 230 (for DP650 mechanism)
1 ≤ n1 + 256 × n2 ≤ 280 (for DP652 mechanism)
1 ≤ n1 + 256 × n2 ≤ 360 (for DP654 mechanism)
1 ≤ n1 + 256 × n2 ≤ 400 (for DP657 mechanism)
[Outline]
This command allows printing in the bit image mode.
Divide the number of dots printed
by 256 and assume its quotient to be n2 and remainder to be n1.
Therefore, the number of
horizontal dots will be n1 + 256 × n2.
If the bit image data is entered beyond the dot positions printable in one line, the surplus
data will be discarded.
Normal data processing is restored after bit image printing.
Printing is done in a single direction.
ESC "−" n
[Function]
Specifying/Canceling the underline
[Code]
<1B>H <2D>H n
[Outline]
This command selects/deselects an underline.
The underline is selected at n = 1 and
deselected at n = 0.
[Default]
n=0
49
CITIZEN
iDP3550/3551 User’s Manual
ESC "1"
(Graphic type)
[Function]
Setting the 1/9-inch line feed width
[Code]
<1B>H <31>H
[Outline]
Only effective for Graphic type.
This command sets the line feed width to 1/9 inch.
ESC "2"
(Graphic type)
[Function]
Setting the 2/9-inch line feed width
[Code]
<1B>H <32>H
[Outline]
Only effective for Graphic type.
This command sets the line feed width to 2/9 inch.
ESC "3"
[Function]
Setting the standard line feed width
[Code]
<1B>H <33>H
[Outline]
This command sets the line feed width as follows.
Character type:
1/6 inch
Graphic type:
2/9 inch
50
CITIZEN
iDP3550/3551 User’s Manual
ESC "C" n
(CBM1 Mode)
[Function]
Setting the page length
[Code]
<1B>H <43>H n
[Range]
1 ≤ n ≤ 127
[Outline]
Sets the 1-page length to n-lines.
ESC "N" n
(CBM1 Mode)
[Function]
Specifying the perforation skip
[Code]
<1B>H <4E>H n
[Range]
1 ≤ n ≤ 126
[Outline]
This command feeds (skips) the lines specified with n without printing.
However, you
cannot specify beyond the length of one page.
ESC "O"
(CBM1 Mode)
[Function]
Canceling the perforation skip
[Code]
<1B>H <4F>H
[Outline]
This command cancels perforation skipping operation.
51
CITIZEN
iDP3550/3551 User’s Manual
ESC "C" n
(CBM2 Mode)
[Function]
Setting the page length
[Code]
<1B>H <43>H n
[Range]
14 ≤ n ≤ 120
[Outline]
Sets the 1-page length to n-lines.
Also it intiates a paging operation, with 3 space lines placed at the beginning and end of a page.
(The first 3-line spacing is initiated when this command isverified.)
[Caution]
If an out-of-range value is specified for “n”, it is set to 66.
The actual number of printable lines is “n-6”.
[Default]
n=66
Patersstraat 106-108
2300 Turnhout
Tel:014/42.55.99
Fax: 014/42.32.64
52
BTW BE 0415.638.961
Rek: 230-0026460-96
info@vanmechelen.be
www.vanmechelen.be
CITIZEN
iDP3550/3551 User’s Manual
ESC "f" 1
[Function]
Form feed (Changing the page)
[Code]
<1B>H <66>H <01>H
[Outline]
This command searches for the beginning of the next page after printing the data in the print
buffer.
ESC "t" n
[Function]
Selecting the character code table
[Code]
<1B>H <74>H n
[Range]
0 ≤ n ≤ 255
[Outline]
This command selects Page-n of Character CodeTable.
[Default]
Depends upon DIP switch setting.
n
0
1
2
3
4
5
Character Code Table
CBM International
CBM Japanese
Code Page 850 (Multilingual)
Code Page 860 (Portuguese)
Code Page 863 (Canadan-French)
Code Page 865 (Nordic)
n
6
7
8
9
255
53
Character Code Table
Code Page 852 (Eastern Europe)
Code Page 866 (Russian)
Code Page 857 (Turkish)
Windows Code
Space Page (For user setting)
CITIZEN
iDP3550/3551 User’s Manual
ESC BEL n1 n2
[Function]
Setting the external device drive pulse width
[Code]
<1B>H <07>H n1 n2
[Range]
1 ≤ n1 ≤ 127
[Outline]
This command sets the power-on time to drive an external device (such as cash drawer).
1 ≤ n2 ≤ 127
Power-on time = n1 × 10 (ms)
Delay time = n2 × 10 (ms)
To actually drive the drawer, use the BEL and FS commands.
[Default]
n1 = n2 = 20
BEL
[Function]
Driving command A for drawer-1
[Code]
<07>H
[Outline]
This command drives the drawer connector No. 2 pin under the condition set with the ESC
BEL n1 n2 command.
This command is executed in order of entry into the input buffer.
54
CITIZEN
iDP3550/3551 User’s Manual
FS
[Function]
Driving command B for drawer-1
[Code]
<1C>H
[Outline]
This command drives the drawer connector No. 2 pin under the condition set with the ESC
BEL n1 n2 command.
SUB
[Function]
Driving command for drawer-2
[Code]
<1A>H
[Outline]
As soon as this command is received, the drawer connector No. 5 pin is driven.
power-on time is 200 ms ON and 200 ms OFF stationary.
The
The drawers 1 and 2 cannot be
driven simultaneously.
RS
[Function]
Buzzer-on
[Code]
<1E>H
[Outline]
This command emits a short warning sound from the printer.
55
CITIZEN
iDP3550/3551 User’s Manual
ESC "P" 0
(iDP3551)
[Function]
Full cut
[Code]
<1B>H<50>H<00>H
[Outline]
This command fully cuts the paper.
ESC "P" 1
(iDP3551)
[Function]
Partial cut
[Code]
<1B>H<50>H<01>H
[Outline]
This command partially cuts the paper.
ESC "R" n
[Function]
Selecting the international character set
[Code]
<1B>H <52>H n
[Range]
0 ≤ n ≤ 10
[Outline]
This command selects the international characters according to the value of n.
n
0
1
2
3
4
5
[Default]
Character Set
U.S.A.
France
Germany
U.K.
Denmark I
Sweden
n
6
7
8
9
10
Character Set
Italy
Spain
Japan
Norway
Denmark II
Depends upon DIP switch setting.
56
CITIZEN
iDP3550/3551 User’s Manual
ESC "&" <0> n1 n2 [m0 m1 ... m5 m6 m7 m8 m9] n2 - n1 + 1
[Function]
Defining the Download character set
[Code]
<1B>H <26>H <00>H n1 n2 [m0 m1 ... m5 m6 m7 m8 m9] n2 - n1 + 1
[Range]
32 ≤ n1 ≤ n2 ≤ 255
[Outline]
This command defines he download characters.
m0 = 0 or m0 = 128
and n2 is to end definition, respectively.
n1 is a character code to start definition
When defining only one character, set n1 = n2.
You can define the ASCII codes ranging from 32 to 255.
Once the download characters
are defined, they remain valid until they are redefined or the download deletion command
(ESC DC2 n1 n2) is executed.
57
CITIZEN
iDP3550/3551 User’s Manual
ESC "%" n
[Function]
Specifying/Canceling the download character set
[Code]
<IB>H <25>H n
[Outline]
This command selects/deselects the download character set.
The download characters
cannot be printed by simply defining them with the above-mentioned ESC & 0 command.
To print them, send this command to the printer.
n
0
30
1
31
Download Character Set
Deselects
Selects
ESC "⁄" n "data" CR or LF
[Function]
Defining the Message
[Code]
<1B>H <2F>H n "data" CR or LF
[Range]
1 ≤ n ≤ 10
[Outline]
This command can define up to a 50-byte message in one line.
If the value of n is
specified beyond the range, the data following n will be treated as the print data.
Once the message is defined, it remains valid until it is redefined.
with CR (0DH) or LF (0AH).
The data should end
If the data exceeds 50 bytes, the subsequent data will be
treated as the print data.
Once the message is defined, it remains valid until it is redefined or the download deletion
command (ESC DC2 n1 n2) is executed.
58
CITIZEN
iDP3550/3551 User’s Manual
ESC DC3 n
[Function]
Printing the message
[Code]
<1B>H <13>H n
[Range]
1 ≤ n ≤ 10
[Function]
This command prints a message.
If the value of n is specified beyond the range, the
message will not be printed.
ESC "y" n
(Friction feed model)
[Function]
Setting the print lines after paper near end detection
[Code]
<1B>H<79>H n
[Range]
0 ≤ n1 ≤ 255
[Outline]
This command sets the number of print lines after paper near end detection.
It stops
printing after printing n × 2 lines since detection of the paper near end, resulting in the paper
near end state (See 4.12 Operation Panel and Display of Error).
The PE signal
(serial/parallel) changes when the paper near end is detected.
[Default]
n=0
59
CITIZEN
iDP3550/3551 User’s Manual
ESC DC2 n1 n2
[Function]
Deleting the download character, message, bit image
[Code]
<1B>H <12>H n1 n2
[Range]
0 ≤ n1 ≤ 3
0 ≤ n2
(Specify 0 at n1 = 0)
(1 ≤ n2 ≤ 10 at n1 = 1)
(32 ≤ n2 ≤ 255 at n1 = 2)
(Specify 0 at n1 = 3)
[Outline]
This command deletes the downloaded characters, message, and bit image.
n1
0
1
2
3
Object Deleted
All(Message, characters, bit image)
Download message
Download characters
Download bit image
With n2, specify which data of the function specified with n1 should be deleted.
n2 = 0
Deletes all the data saved with the download function specified with n1.
n2 ≠ 0
Deletes the data downloaded at the value specified with n2 (Value specified when
saving with each download command), of the download function specified with
n1.
60
CITIZEN
iDP3550/3551 User’s Manual
GS "*" n1 n2 [d] n1 × n2 × 8
(Graphic type)
[Function]
Defining the download bit image
[Code]
<1D>H <2A>H <n1> <n2> [<d>] n1 × n2 × 8
[Range]
1 ≤ n1 ≤ 45
0 ≤ n2 ≤ 24
Note) Take care that the number of data (n1×n2×8) is equal to or smaller than 2,048.
[Outline]
This command defines the download bit image having the dots specified n1 and n2.
The
number of horizontal dots is represented by n1 × 8 and that of vertical dots is represented by
n2 × 8, respectively.
printout.)
d denotes the number to be registered.
d denotes the bit image data.
(See a download bit image
Once the download bit image is defined, it
remains valid until it is redefined or the download deletion command (ESC DC2 n1 n2) is
executed.
61
CITIZEN
iDP3550/3551 User’s Manual
GS "⁄" m
(Graphic type)
[Function]
Printing the download bit image
[Code]
<1D>H <2F>H m
[Range]
0 ≤ m ≤ 255
[Outline]
This command prints the bit image saved in the number specified with m.
[Caution]
If the print buffer contains the data, this command will be ignored.
If the bit image has not
been saved in the specified number, this command will be ignored.
Nothing is printed when m is other than 0,1,2 or 3.
62
CITIZEN
iDP3550/3551 User’s Manual
14.2 Star Mode
14.2.1 Command List
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
Command
ESC R n
ESC 6
ESC 7
ESC M
ESC P
ESC :
SO
DC4
ESC E
ESC F
ESC −
ESC _
ESC 4
ESC 5
SI
DC2
LF
CR
ESC z
ESC 0
ESC a n
FF
ESC C n
ESC C <0> n
VT
ESC B [n]k NUL
ESC N n
ESC O
ESC l n
ESC Q n
HT
ESC D [n]k NUL
ESC 1
ESC A n
ESC 2
ESC J n
ESC K n1 <0>
ESC L n1 n2
ESC h n
ESC & <0> n1 n2
41
ESC % n
Function
Selecting the international character set
NOP
NOP
NOP
NOP
NOP
Specifying the double width character
Canceling the double width character
Specifying the highlight character
Canceling the highlight character
Specifying/Canceling the underline
NOP
Specifying the red print
Canceling the red print
Specifying the inverted character
Canceling the inverted character
Printing and paper feed
Printing
Setting the 1/6-inch line feed
NOP
Setting the n-line paper feed
Form feed (Change the page)
Setting the n-line page length
Setting the n-inch page length
Vertical tab
Setting the vertical tab position
Setting the lower margin
Canceling the lower margin
Setting the left margin
Setting the right margin
Horizontal tab
Setting the horizontal tab position
Setting the 1/9-inch line feed width
NOP
Setting the 2/9-inch line feed width
NOP
Specifying the 8-dot standard density bit image
Specifying the 8-dot double density bit image
Specifying/Canceling the double height character
Defining the download character
Specifying/Canceling the download
character set
63
Code
1BH 52H n
1BH 36H
1BH 37H
1BH 4DH
1BH 50H
1BH 3AH
0EH
14H
1BH 45H
1BH 46H
1BH 2DH n
1BH 5FH n
1BH 34H
1BH 35H
0FH
12H
0AH
0DH
1BH 7AH
1BH 30H
1BH 61H n
0CH
1BH 43H n
1BH 43H 00H n
0BH
1BH 42H [n]k 00H
1BH 4EH n
1BH 4FH
1BH 6CH n
1BH 51H n
09H
1BH 44H [n]k 00H
1BH 31H
1BH 41H n
1BH 32H
1BH 4AH n
1BH 4BH n1 00H
1BH 4CH n1 n2
1BH 68H n
1BH 26H 00H n1 n2
1BH 25H n
Page
65
----------65
66
66
66
67
--67
67
68
68
68
69
69
--70
70
70
70
71
71
72
72
72
73
73
74
75
--75
--76
77
77
78
79
CITIZEN
iDP3550/3551 User’s Manual
42
43
44
45
46
47
48
49
Command
ESC BEL n1 n2
BEL
FS
SUB
RS
CAN
DC3
DC1
50
ESC U n
51 ESC @
52 ENQ
53 STX
54 ETX
ESC d 0
55
ESC d <0>
ESC d 1
56
ESC d <1>
57 ESC t n
58 ESC ⁄ n
59 ESC DC3 n
60
ESC y n
61
ESC DC2 n1 n2
62
63
GS * n1 n2
GS ⁄ m
Function
Setting the external device drive pluse width
Driving command A for drawer-1
Driving command B for drawer-1
Driving command for drawer-2
Buzzer-on
Canceling the print data
Setting the deselect mode
Setting the Select mode
Selecting the unidirectional/bidirectional
Print mode
Initializing the printer
Enquiry
Text start
Text end command
Full cut
Partial cut
Selecting the character code table
Defining the message
Printing the message
Setting the print lines after paper near end
Detection
Deleting the download character, message
bit image
Defining the download bit image
Printing the download bit image
64
Code
1BH 07H n1 n2
07H
1CH
1AH
1EH
18H
13H
11H
Page
80
80
81
81
81
82
82
82
1BH 55H n
83
1BH 40H
05H
02H
03H
1BH 64H 30H
1BH 64H 00H
1BH 64H 31H
1BH 64H 01H
1BH 74H n
1BH 2FH n
1BH 13H n
1BH 79H n
83
84
85
85
1BH 12H n1 n2
1DH 2AH n1 n2
1DH 2FH m
87
87
87
88
88
89
89
90
91
CITIZEN
iDP3550/3551 User’s Manual
Details
ESC "R" n
[Function]
Selecting the international character set
[Code]
<1B>H <52>H n
[Range]
0 ≤ n ≤ 10
[Outline]
This command selects the international characters according to the value of n.
n
0
1
2
3
4
5
Character Set
U.S.A.
France
Germany
U.K.
Denmark I
Sweden
n
6
7
8
9
10
Character Set
Italy
Spain
Japan
Norway
Denmark II
[Default]
Depends upon DIP switch setting.
[Function]
Specifying the double width character
[Code]
<0E>H
[Outline]
The data following this command is printed doubled in the horizontal direction.
SO
Double
width characters remain valid until the double width character cancel command is entered,
but they are also cancelled after they are printed one line.
Note that the double width
characters take up two ordinary characters worth of width.
65
CITIZEN
iDP3550/3551 User’s Manual
DC4
[Function]
Canceling the double width character
[Code]
<14>H
[Outline]
This command deselects the double width characters set with SO.
The data following this
command will be printed in ordinary characters.
ESC "E"
[Function]
Specifying the highlight character
[Code]
<1B>H <45>H
[Outline]
The data following this command is printed in highlight (double) characters.
The highlight
characters remain valid until the highlight character deselection command is entered.
ESC "F"
[Function]
Canceling the highlight character
[Code]
<1B>H <46>H
[Outline]
This command deselects the highlight characters set with ESC "E".
The data following
this command will be printed in ordinary characters.
66
CITIZEN
iDP3550/3551 User’s Manual
ESC "−" n
[Function]
Specifying/Canceling the underline
[Code]
<1B>H <2D>H n
[Outline]
This command selects/deselects an underline.
The underline is selected at n = 1 and
deselected at n = 0.
The space by the horizontal tab is not underlined.
ESC "4"
[Function]
Specifying the red print
[Code]
<1B>H <34>H
[Outline]
This command prints its subsequent data in red.
print deselection command is entered.
This command remains valid until the red
Red and black characters cannot be mixed in one
line.
ESC "5"
[Function]
Canceling the red print
[Code]
<1B>H <35>H
[Outline]
This command deselects red print.
67
CITIZEN
iDP3550/3551 User’s Manual
SI
[Function]
Specifying the inverted character
[Code]
<0F>H
[Outline]
This command selects and prints the inverted characters.
line.
Otherwise, it will be invalid.
Enter it at the beginning of one
Erect and inverted characters cannot be mixed in one
line.
DC2
[Function]
Canceling the Inverted character
[Code]
<12>H
[Outline]
This command deselects the inverted characters.
Enter this command at the beginning of
one line.
LF
[Function]
Printing and paper feed
[Code]
<0A>H
[Outline]
If the print buffer contains the data, this command will feed the line after printing.
If not,
the command only feeds the line.
BTW BE 0415.638.961
Rek: 230-0026460-96
info@vanmechelen.be
www.vanmechelen.be
Patersstraat 106-108
2300 Turnhout
Tel:014/42.55.99
Fax: 014/42.32.64
68
CITIZEN
iDP3550/3551 User’s Manual
CR
[Function]
Printing and paper feed (Same as LF)
[Code]
<0D>H
[Outline]
The function is the same "LF."
However, if the DIP switch segment 1-6 is set to ON, this
command is ignored.
ESC "z"
[Function]
Setting the standard line feed width
[Code]
<1B>H <7A>H
[Outline]
This command sets the line feed width as follows.
For character type: 1/6
For graphic type:
2/9 inch
ESC "a" n
[Function]
Setting the n-line paper feed
[Code]
<1B>H <61>H n
[Range]
1 ≤ n ≤ 127
[Outline]
This command feeds the paper by the number of lines specified with n.
to 127 lines.
You can set n = 1
If the print buffer contains the data, use of this command feeds the paper by
n-lines after printing the data.
69
CITIZEN
iDP3550/3551 User’s Manual
FF
[Function]
Form feed (Changing the page)
[Code]
<0C>H
[Outline]
This command searches for the head of the next page after printing the data in the print
buffer.
ESC "C" n
[Function]
Setting the n-line page length
[Code]
<IB>H <43>H n
[Range]
1 ≤ n ≤ 255
[Outline]
Sets the 1-page length to n-lines.
[Default]
n = 42
ESC "C" <0> n
[Function]
Setting the n-inch page length
[Code]
<1B>H <43>H <0> n
[Range]
1 ≤ n ≤ 127
[Outline]
This command sets the length of one page to n -inches.
70
CITIZEN
iDP3550/3551 User’s Manual
VT
[Function]
Vertical tab
[Code]
<0B> H
[Outline]
This command feeds the paper to the next vertical tab position.
vertical tab position has been set.
It cannot be fed unless the
If the current position is equal to or greater than the
maximum set vertical tab position, it will be fed to the head of the next page.
ESC "B" [n]k NUL
[Function]
Setting the vertical tab position
[Code]
<1B>H <42>H [n]k <00>H
[Range]
1 ≤ n ≤ 255
1 ≤ k ≤ 16
[Outline]
This command cancels the already set vertical tab positions and sets new vertical tab
positions.
can be set.
They are set in the ascending order and ends with <00>.
Up to 16 vertical tabs
If the tab setting position <nk> is equal or smaller than the preceding set
position <nk-1>, it is assumed that setting of the vertical tabs has been completed.
71
CITIZEN
iDP3550/3551 User’s Manual
ESC "N" n
[Function]
Setting the lower margin
[Code]
<1B>H <4E>H n
[Range]
0 ≤ n ≤ 255
[Outline]
This command sets the n-line lower margin.
[Default]
n=0
ESC "O"
[Function]
Canceling the lower margin
[Code]
<1B>H <4F>H
[Outline]
This command deselects the set lower margin.
ESC "l" n
[Function]
Setting the left margin
[Code]
<1B>H <6C>H n
[Range]
0 ≤ n ≤ (Right margin - 2)
[Outline]
This command sets the left margin and printing starts from the column next to the set
margin.
72
CITIZEN
iDP3550/3551 User’s Manual
ESC "Q" n
[Function]
Setting the right margin
[Code]
<1B>H <51>H n
[Range]
2 ≤ n ≤ (Max. print columns)
[Outline]
This command sets the right margin and printing is performed up to n -columns.
HT
[Function]
Horizontal tab
[Code]
<09>H
[Outline]
This command moves a printing position to the preset next horizontal tab position.
This
command will be ignored unless there is the next horizontal tab position.
73
CITIZEN
iDP3550/3551 User’s Manual
ESC "D" [n]k NUL
[Function]
Setting the horizontal tab position
[Code]
<1B>H <44>H [n]k <00>H
[Range]
1 ≤ n ≤ Max. print columns – 1
1 ≤ k ≤ 16
[Outline]
This command sets the horizontal tab positions.
n indicates the number of lines from the
head of the line to the horizontal tab setting position.
k indicates the number of horizontal
tab positions to be set.
The tab position is set at the character width × n from the head of the line.
The character
width at this time includes the right space of the character and will be doubled if the double
width characters are specified.
The data <n>k indicating the set position is entered in the ascending order and ends with
<00>H.
ESC D NUL clears all the set tab positions.
After clearing the tab positions, HT
will be ignored.
[Caution]
If the data <n>k is equal to or smaller than the preceding data <n>k - 1, it is assumed that
horizontal tab setting has been completed.
In that case, the subsequent data will be
processed as regular one.
Up to 16 tab positions can be set.
regular data.
If the data exceeds this limit, it will be processed as
If the data <n>k exceeds the one-line print range, the set column position will
equal the maximum print columns + 1.
If the character width is changed after setting the horizontal tab positions, they will not
change.
74
CITIZEN
iDP3550/3551 User’s Manual
ESC "1"
(G raphic Type)
[Function]
Setting the 1/9-inch line feed width
[Code]
<1B>H <31>H
[Outline]
This command sets the line feed width to 1/9 inch.
ESC "2"
(Graphic Type)
[Function]
Setting the 2/9-inch line feed width
[Code]
<1B>H <32>H
[Outline]
This command sets the line feed width to 2/9 inch.
75
CITIZEN
iDP3550/3551 User’s Manual
ESC "K" n1 <0> m1 m2 ...
(Graphic Type)
[Function]
Specifying the 8-dot standard density bit image
[Code]
<1B>H <4B>H n1 <00>H m1 m2 ...
[Range]
1 ≤ n1 ≤ 115/2 (for DP650 mechanism)
1 ≤ n1 ≤ 140/2 (for DP652 mechanism)
1 ≤ n1 ≤ 180/2 (for DP654 mechanism)
1 ≤ n1 ≤ 200/2 (for DP657 mechanism)
[Outline]
This command prints the bit image by the number of data specified with n1.
be unidirectional.
ignored.
Printing will
The surplus data exceeding the printable quantity in one line will be
The printer will automatically return to the character mode after printing the bit
image.
76
CITIZEN
iDP3550/3551 User’s Manual
ESC "L" n1 n2 m1 m2 ...
(Graphic Type)
[Function]
Specifying the 8-dot double density bit image
[Code]
<1B>H <4C>H n1 n2 m1 m2 ...
[Range]
1 ≤ n1 + 256 × n2 ≤ 230 (for DP650 mechanism)
1 ≤ n1 + 256 × n2 ≤ 280 (for DP652 mechanism)
1 ≤ n1 + 256 × n2 ≤ 360 (for DP654 mechanism)
1 ≤ n1 + 256 × n2 ≤ 400 (for DP657 mechanism)
[Outline]
This command prints the 8-dot double density (half-dot print) bit image.
unidirectional.
ignored.
Printing will be
The surplus data exceeding the printable quantity in one line will be
The printer will automatically return to the character mode after printing the bit
image.
The relations between the printing head pin numbers and the data are the same as the 8-dot
standard density bit image command, <ESC> "K.".
When printing the double density bit
image, the horizontally adjacent dots cannot be printed.
ESC "h" n
(Graphic Type)
[Function]
Specifying/Canceling the double height character
[Code]
<1B>H <68>H n
[Outline]
The data following this command is printed in double height characters, except the bit image
mode <ESC> "K" and <ESC> "L".
In combination with the <SO> command, this
command can print double height, double width characters.
It cannot be combined with the inverted character command, <SI>.
The double height
characters and ordinary characters shall be bottom -justified.
77
CITIZEN
iDP3550/3551 User’s Manual
n
0
30
1
31
Double height character command
Deselects
Selects
ESC "&"<O> n1 n2 [m0 m1 m2 m3 m4 m5 m6 m7 m8 m9] n2- n1 + 1
[Function]
Defining the download character set
[Code]
<1B>H <26>H <00>H n1 n2 [m0 m1 ... m5 m6 m7 m8 m9] n2 - n1 + 1
[Range]
32 ≤ n1≤ n2 ≤ 255,
[Outline]
This command defines the download characters.
m0 = 0 or m0 = 128
and n2 is to end definition, respectively.
n1 is a character code to start definition
When defining only one character, set n1 = n2.
You can define the ASCII codes ranging from 32 to 255.
The horizontally adjacent dots cannot be printed.
Once the download bit image is defined,
it remains valid until it is redefined or the download deletion command(ESC DC2 n1 n2) is
executed.
Horizontal adjacent dots cannot be printed.
78
CITIZEN
iDP3550/3551 User’s Manual
ESC "%" n
[Function]
Specifying/Canceling the download character set
[Code]
<IB>H <25>H n
[Outline]
This command selects/deselects the download character set.
The download characters
cannot be printed by simply defining them with the above-mentioned ESC & 0 command.
To print them, send this command to the printer.
n
0
30
1
31
Download Character Set
Deselects
Selects
79
CITIZEN
iDP3550/3551 User’s Manual
ESC BEL n1 n2
[Function]
Setting the external device drive pulse width
[Code]
<1B>H <07>H n1 n2
[Range]
1 ≤ n1 ≤ 127
1 ≤ n2 ≤ 127
[Outline]
This command sets the power-on time to drive an external device(cash drawer).
Power-on time = n1 × 10 (ms)
Delay time = n2 × 10 (ms)
To actually drive the drawer, use the <BEL> and <FS> commands.
[Default]
n1 = n2 = 20 (200ms)
BEL
[Function]
Driving command A for drawer-1
[Code]
<07>H
[Outline]
This command drives the drawer connector no. 2 pin under the condition set with the
<ESC><BEL> n1 n2 command. This command is executed in order of entry into the input
buffer.
80
CITIZEN
iDP3550/3551 User’s Manual
FS
[Function]
Driving command B for drawer-1
[Code]
<1C>H
[Outline]
This command drives the drawer connector no. 2 pin under the condition set with the
<ESC><BEL> n1 n2 command.
SUB
[Function]
Driving command for drawer-2
[Code]
<1A>H
[Outline]
As soon as this command is received, the drawer connector no. 5 pin is driven.
power-on time is 200 ms ON and 200 ms OFF stationary.
The
The drawers 1 and 2 cannot be
driven simultaneously.
RS
[Function]
Buzzer-on
[Code]
<1E>H
[Outline]
This command emits a short warning sound from the printer.
81
CITIZEN
iDP3550/3551 User’s Manual
CAN
[Function]
Canceling the print data
[Code]
<18>H
[Outline]
This command clears the input buffer and print buffer.
In the STX-EXT mode of the serial
interface printer, the command clears the data in the data buffer and ends the STX-ETX
mode.
DC3
[Function]
Setting the deselect mode
[Code]
<13>H
[Outline]
If the printer receives <DC3>, it will ignore the subsequent data.
The Deselect mode is
cancelled by <DC1>.
DC1
[Function]
Setting the select mode
[Code]
<11H>
[Outline]
If the printer receives this command, it will save the subsequent data in the input buffer.
82
CITIZEN
iDP3550/3551 User’s Manual
ESC "U" n
[Function]
Selecting the Unidirectional/Bidirectional print mode
[Code]
<1B>H <55>H n
[Range]
0 ≤ n ≤ 255
[Outline]
This command selects or deselects unidirectional print.
n0 = 0
n0 = 1
Bidirectional print
Unidirectional print
ESC "@"
[Function]
Initializing the printer
[Code]
<1B>H <40>H
[Outline]
This command cancels various conditions set after power-on to initializes the printer to the
conditions having existed at power-on.
83
However, the input buffer is not initialized.
CITIZEN
iDP3550/3551 User’s Manual
ENQ
[Function]
Enquiry
[Code]
<05>H
[Outline]
This command is valid only for the serial interface.
information.
The printer sends the status
If this command is entered after receiving the text information in the
STX-ETX mode, the printer will send the status information and check byte.
STX
[Function]
Text start
[Code]
<02>H
[Outline]
This command is valid only for the serial i nterface.
84
It effectuates the STX-ETX mode.
CITIZEN
iDP3550/3551 User’s Manual
ETX
[Function]
Text end
[Code]
<03>H
[Outline]
This command is valid only for the serial interface.
It ends the STX-ETX mode and prints
the data.
85
CITIZEN
iDP3550/3551 User’s Manual
*ETX-STX Mode
1
STX/ETX Mode Start
Sends ENQ
Sends ENQ
NO
Receives Status
Receives Status
Receives Check Byte
Data Buffer Empty ?
Status Error ?
YES
YES
NO
Sends STX
Odd Parity Check ?
Check Byte
= Test Byte ?
NO
YES
NO
Sends ETX
Sends CAN
YES
Sets Test Byte To
FFH
(Print)
Sets Test Byte To
00
STX-ETX
Mode End
Exclusive ORs Test Byte
and Sent Data
Test Byte
STX-ETX Mode Data
Block Ready to Send ?
Sends Data to Printer
NO
NO
YES
Last Data in 1 Block ?
RET
YES
1
86
CITIZEN
iDP3550/3551 User’s Manual
ESC "d" "0" or ESC "d" <0>
(iDP3551 Only)
[Function]
Full cut
[Code]
<1B>H<64>H<30>H or <IB>H<64>H<00>H
[Outline]
This command fully cuts the paper.
ESC "d" "1" or ESC "d" <1>
(iDP3551 Only)
[Function]
Partial cut
[Code]
<1B>H<64>H<31>H or <1B>H<64>H<01>H
[Outline]
This command partially cuts the paper.
ESC "t" n
[Function]
Selecting the character code table
[Code]
<1B>H <74>H n
[Range]
0 ≤ n ≤ 255
[Outline]
This command selects Page-n of Character CodeTable.
[Default]
Depends on DIP switch setting.
n
0
1
2
3
4
5
Character Code Table
Star International
Star Japanese
Code Page 850 (Multilingual)
Code Page 860 (Portuguaese)
Code Page 863 (Canadan-French)
Code Page 865 (Nordic)
n
6
7
8
9
255
87
Character Code Table
Code Page 852 (Eastern Europe)
Code Page 866 (Russian)
Code Page 857 (Turkish)
Windows Code
Space Page (For user setting)
CITIZEN
iDP3550/3551 User’s Manual
ESC "⁄" n "data" CR or LF
[Function]
Defining the message
[Code]
<1B>H <2F>H n "data" CR or LF
[Range]
1 ≤ n ≤ 10
[Outline]
This command can define up to a 50-byte message in one line.
If the value of n is
specified beyond the range, the data following n will be treated as the print data.
Once the message is defined, it remains valid until it is redefined.
with CR (0DH) or LF (0AH).
The data should end
If the data exceeds 50 bytes, the subsequent data will be
treated as the print data.
Once the message is defined, it remains valid until it is redefined or the download deletion
command (ESC DC2 n1 n2) is executed.
ESC DC3 n
[Function]
Printing the message
[Code]
<1B>H <13>H n
[Range]
1 ≤ n ≤ 10
[Function]
This command prints a message.
If the value of n is specified beyond the range or if
nothing is specified to n, the message will not be printed.
88
CITIZEN
iDP3550/3551 User’s Manual
ESC "y" n
(Friction feed model)
[Function]
Setting the print lines after paper near end detection
[Code]
<1B>H<79>H n
[Range]
0 ≤ n1 ≤ 255
[Outline]
This command sets the number of print lines after paper near end detection.
It stops
printing after printing n × 2 lines since detection of the paper near end, resulting in the paper
near end state (See 4.12 Operation Panel and Display of Error).
The PE signal (parallel
interface only) changes when the paper near end is detected.
[Default]
n=0
ESC DC2 n1 n2
[Function]
Deleting the download character, message, bit image
[Code]
<1B>H <12>H n1 n2
[Range]
0 ≤ n1≤ 3
0 ≤ n2
(Specify 0 at n1 = 0)
(1 ≤ n2 ≤ 10 at n1 = 1)
(32 ≤ n2 ≤ 224 at n1 = 2)
(Specify 0 at n1 = 3)
[Outline]
This command deletes the downloaded characters, message, and bit image.
n1
0
1
2
3
Object Deleted
All(Message, characters, bit image)
Download message
Download characters
Download bit image
With n2, specify which data of the function specified with n1 s hould be deleted.
n2 = 0
n2 ≠ 0
Deletes all the download function specified with n1.
Deletes the data downloaded at the value specified with n2 (value specified
when saving with each download command), of the download function
specified with n1.
89
CITIZEN
iDP3550/3551 User’s Manual
GS "*" n1 n2 [d] n1 × n2 × 8
(Graphic type)
[Function]
Defining the download, bit image
[Code]
<1D>H <2A>H <n1> <n2> [<d>] n1 × n2 × 8
[Range]
1 ≤ n1 ≤ 45
0 ≤ n2 ≤ 24
Note) Take care that the number of data(n1×n2×8) is equal to or smaller than 2,048.
[Outline]
This command defines the download bit image having the dots specified n1 and n2.
The
number of horizontal dots is represented by n1 × 8 and that of vertical dots is represented by
n2 × 8, respectively.
printout.)
d denotes the number to be registered.
d denotes the bit image data.
(See a download bit image
Once the download bit image is defined, it
remains valid until it is redefined or the download deletion command(ESC DC2 n1 n2) is
executed.
90
CITIZEN
iDP3550/3551 User’s Manual
GS ⁄ m
(Graphic Type)
[Function]
Printing the download bit image
[Code]
<1D>H <2F>H m
[Range]
0 ≤ m ≤ 255
[Outline]
This command prints the bit image saved in the number specified with m.
[Caution]
If the print buffer contains the data, this command will be ignored.
If the bit image has not
been saved in the specified number, this command will be ignored.
Nothing is printed when m is other than 0,1,2 or 3.
91
CITIZEN
iDP3550/3551 User’s Manual
14.3 ESC/POS Mode
14.3.1 Command List
Command
1
2
3
4
5
HT
LF
CR
ESC (Space) n
ESC ! n
6
ESC % n
9
ESC & s n m
[a[p] s × a]
ESC ∗ m n1 n2
[d] n1 + 256 × n2
ESC 2
10
ESC 3 n
11
12
13
14
15
ESC <
ESC @
ESC D [n] k NUL
ESC J n
ESC R n
16
ESC U n
17
ESC c 0 n
18
ESC c 4 n
19
20
21
22
23
24
25
26
27
28
29
30
31
ESC c 5 n
ESC d n
ESC i
ESC m
ESC p m n1 n2
ESC r n
ESC t n
ESC u n
ESC v
ESC { n
GS E n
ESC ⁄ n
ESC DC3 n
32
ESC y n
33
ESC DC2 n1 n2
34
35
GS ∗ n1 n2
GS ⁄ m
7
8
Function
Horizontal tab
Printing and paper feed
Printing
Setting thr character right space
Setting print mode batch
Specifying/Canceling the download
character set
Defining the download character set
Specifying the bit image mode
Setting the 1/6-inch line feed rate
Setting the line feed width in minimum
pitch increments
NOP
Initializing the printer
Setting the Horizontal tab position
NOP
Selecting the international character set
Specifying/Canceling the unidirectional
print mode
NOP
Selecting the paper near end sensor valid
for print stop
Selecting the panel switch enable/disable
Printing and n-line paper feed
Full cut
Partial cut
Specifying the pulse generation
Selecting the printing color
Selecting the character code table
Sending the status for peripheral device
Sending the printer status
Specifying/Canceling the inverted character print
NOP
Defining the message
Printing the message
Setting the print lines after paper near end
detection
Deleting the download character, message, bit
image
Defining the download bit image
Printing the download bit image
92
Code
09H
0AH
0DH
1BH 20H n
1BH 21H n
Page
93
93
94
94
95
1BH 25H n
96
1BH 26H s n m
[a[p]s×a] m-n+1
1BH 2AH m n1 n2
[d] n1 + 256×n2
1BH 32H
97
98
99
1BH 33H n
99
1BH 3CH
1BH 40H
1BH 44H [n] k 00H
1BH 4AH n
1BH 52H n
--99
100
--101
1BH 55H n
102
1BH 63H 30H n
---
1BH 63H 34H n
103
1BH 63H 35H n
1BH 64H n
1BH 69H
1BH 6DH
1BH 70H m n1 n2
1BH 72H n
1BH 74H n
1BH 75H n
1BH 76H
1BH 7BH n
1DH 45H n
1BH 2FH n
1BH 13H n
103
104
104
104
105
106
106
107
108
109
--109
110
1BH 79H n
110
1BH 12H n1 n2
111
1DH 2AH n1 n2
1DH 2FH m
112
113
CITIZEN
iDP3550/3551 User’s Manual
Details
HT
[Function]
Horizontal tab
[Code]
<09>H
[Outline]
This command moves a printing position to the next horizontal tab position.
If the next
horizontal tab position is not set, this command will be ignored.
[Caution]
The horizontal tab position is set by <ESC> D.
Initial setting of the horizontal tab position
is every 8 characters (9th, 17th, 25th culomns, and so on).
LF
[Function]
Printing and paper feed
[Code]
<0A>H
[Outline]
This command prints one line worth of the data saved in the print buffer and feeds the line
based on the set line feed value.
The head of the line is assumed to be the next print start
position.
BTW BE 0415.638.961
Rek: 230-0026460-96
info@vanmechelen.be
www.vanmechelen.be
Patersstraat 106-108
2300 Turnhout
Tel:014/42.55.99
Fax: 014/42.32.64
93
CITIZEN
iDP3550/3551 User’s Manual
CR
[Function]
Printing
[Code]
<0D>H
[Outline]
This command prints the data.
If the DIP switch segment 1-6 is set to OFF, the printer will
print the data in the print buffer and feed the paper by one line.
If it is set to ON, the
printer will print the data in the print buffer and will not feed the paper.
ESC " " n
[Function]
Setting the character right space
[Code]
<1B>H <20>H n
[Range]
0 ≤ n ≤ 32
[Outline]
This command sets the right space of the character.
[Caution]
In the double width mode, the right space will be double the set amount.
Set the space in
increments of half dot.
[Default]
n=0
94
CITIZEN
iDP3550/3551 User’s Manual
ESC "!" n
[Function]
Setting the print mode batch
[Code]
<1B>H <21>H n
[Range]
0 ≤ n ≤ 255
[Outline]
Sets the print mode. "n" (Each bit) has the following meanings.
Bit
[Caution]
Values
Function
0
1
0
1
2
3
Undefined
Undefined
Undefined
High-lighting
−
−
−
−
−
−
Canceled
4
Double height
Canceled
5
6
7
Double width
Undefined
Underline
Canceled
Specified
Specified
(Graphic Type)
Specified
−
−
Canceled
Specified
The entire character print width is underlined, but the portion skipped by HT is not.
double height and double width are selected, the characters will be quadrupled.
If both
If the
double width characters are selected, some dots may not be printed depending on the
preceding one.
Double height is selectable only for graphic type.
[Default]
n=0
95
CITIZEN
iDP3550/3551 User’s Manual
ESC "%" n
[Function]
Specifying/Canceling the download character set
[Code]
<1B>H <25>H n
[Range]
0 ≤ n ≤ 255
[Outline]
This command selects/deselects the download character set.
n is valid only for the least
significant bit.
Setting n0 = 1 selects the download character set.
Setting n0 = 0 deselects the download character set.
[Default]
n=0
96
CITIZEN
iDP3550/3551 User’s Manual
ESC "&" s n m [a[p] s × a]m - n + 1
[Function]
Defining the download character set
[Code]
<1B>H <26>H s n m [a[p] ... <ps × a>] m - n + 1
[Range]
s=2
32 ≤ n ≤ m ≤ 255
0≤a≤9
0 ≤ p1 ... ps × a ≤ 255
[Outline]
This command defines the download alphenumeric or Katakana.
s denotes the number of
bytes in the vertical direction, n the start character code, and m the end character code,
respectively.
When defining only one character, set n = m.
The 224 ASCII code characters, 32 to 255, are definable.
the horizontal direction to be defined.
a specifies the number of dots in
p is the data you want to define and shows the
a-dots worth of pattern in the horizontal direction from the left edge.
pattern on the right side will be a space.
The remaining
Once the download characters are defined, they
remain valid until they are redefined or the download deletion command (ESC DC2 n1 n2)
is executed.
[Default]
Same as the internal character set.
[Caution]
The horizontally adjacent dots cannot be printed.
The 2nd-byte data in the vertical
direction is valid only for the most significant bit.
97
CITIZEN
iDP3550/3551 User’s Manual
ESC "*" m n1 n2 [d] n1 + 256 × n2
[Function]
Specifying the bit image mode
[Code]
<1B>H <2A>H m n1 n2 [d] n1 + 256×2
[Range]
m = 0, 1
0 ≤ n1 ≤ 255
0 ≤ n2 ≤ 3
0 ≤ d ≤ 255
[Outline]
This command specifies the bit image for the mode m as to the number of dots specified
with n1 and n2.
Divide the number of dots printed by 256 and assume its quotient to be n2
and remainder to be n1.
Therefore, the number of horizontal dots will be n1 + 256 × n2.
If the bit image data is entered beyond the dot positions printable in one line, the surplus
data will be discarded.
m
Vertical
Dots
Dot Density
0
1
8
8
Single density
Double density
[Caution]
The following table shows the bit image modes for m.
Horizontal Direction
Total Dots
Adjacent Dot
Setting
DP-650
DP-652
DP-654
Allowed
115
140
180
Disallowed
230
280
360
DP-657
200
400
If the value of m is beyond the conditions, the data subsequent to n1 will be processed as
normal data.
Normal data processing will be restored after completing bit image print.
98
CITIZEN
iDP3550/3551 User’s Manual
ESC "2"
(Character Type)
[Function]
Setting the standard line feed width
[Code]
<1B>H <32>H
[Outline]
This command sets the following line feed width.
For charactor type:
1/6 inch.
For graphic type:
2/9 inche
ESC "3" n
(Graphic Type)
[Function]
Setting the line feed width in minimum pitch increments
[Code]
<1B>H <33>H n
[Outline]
This command is only effective for graphic type. This command sets the line feed width to
n/9 inch.
[Default]
n=2
ESC "@"
[Function]
Initializing the printer
[Code]
<1B>H <40>H
[Outline]
This command cancels various conditions set after power-on to initializes the printer to the
conditions having existed at power-on.
However, the print buffer, input buffer, and
external device drive pulse width are not initialized.
The settings of the DIP switch
segments are not re-read.
99
CITIZEN
iDP3550/3551 User’s Manual
ESC "D" [n]k NUL
[Function]
Setting the Horizontal tab position
[Code]
<1B>H <44>H [n]k <00>H
[Range]
1 ≤ n ≤ 255
0 ≤ k ≤ 32
[Outline]
This command sets the horizontal tab position.
n denotes the number of columns from the
head of the line to the horizontal tab setting.
k denotes the number of horizontal tab
positions to be set.
line.
The tab position is set at the character width × n from the head of the
The character width at this time includes the space to the right of the character; it will
be double the normal character width if the double width characters are selected.
The data <n>k denoting the set position is entered in the ascending order and ends with
<00>H.
[Caution]
ESC D NUL clears all the set tab positions.
HT is ignored after clearing.
If the data <n>k is equal to or smaller than the preceding data <n>k - 1, it is assumed that
horizontal tab setting has been completed.
If this is the case, the subsequent data will be
processed as normal data.
Up to 16 horizontal tabs can be set.
ones.
The data beyond this limit are processed as normal
If the data <n>k exceeds the one-line print range, set the "set column position =
maximum print columns + 1."
Even if the character width is changed after setting the horizontal tab position, the latter will
not change.
[Default]
Every 8 characters (9th, 17th, 25th column, and so on)
100
CITIZEN
iDP3550/3551 User’s Manual
ESC "R" n
[Function]
Selecting the international character set
[Code]
<1B>H <52>H n
[Range]
0 ≤ n ≤ 10
[Outline]
This command selects the international characters according to the value of n.
n
0
1
2
3
4
5
[Default]
Character Set
U.S.A.
France
Germany
U.K.
Denmark I
Sweden
n
6
7
8
9
10
Character Set
Italy
Spain
Japan
Norway
Denmark II
Depends upon DIP switch setting.
101
CITIZEN
iDP3550/3551 User’s Manual
ESC "U" n
[Function]
Specifying/Canceling the Unidirectional print mode
[Code]
<1B>H <55>H n
[Range]
0 ≤ n ≤ 255
[Outline]
This command selects/deselects unidirectional print.
n is valid only for the least significant
bit.
n
0
1
[Caution]
Function
Deselects
Selects
If unidirectional print is selected, the printer will print from the left to the right.
When you
want to prevent horizontal shear in printing at high accuracy, specify unidirectional print
with this command. (For double height print, etc.)
102
CITIZEN
iDP3550/3551 User’s Manual
ESC "c" "4" n
[Function]
Selecting the paper near end sensor valid for print stop
[Code]
<1B>H<63>H<34>H n
[Range]
0 ≤ n ≤ 255
[Outline]
This command selects the no-paper detector state in which printing should be stopped.
[Default]
Value
Bit
Function
0
1
2
3
4
5
6
7
Paper near end
Undefined
Undefined
Undefined
Undefined
Undefined
Undefined
Undefined
0
Disabled
1
Enabled
−
−
−
−
−
−
−
−
−
−
−
−
−
−
n=1
ESC "c" "5" n
[Function]
Selecting the panel switch enable/disable
[Code]
<1B>H <63>H <35>H n
[Range]
0 ≤ n ≤ 255
[Outline]
This command enables/disables the panel switches. n is valid only for the least significant
bit.
Setting n = 1 disables the panel switches.
Setting n = 0 enables the panel switches.
[Caution]
If the panel switches are disabled with this command, the LF switch will be disabled.
Therefore, the paper cannot be fed by the LF switch.
[Default]
n=0
103
CITIZEN
iDP3550/3551 User’s Manual
ESC "d" n
[Function]
Printing and n-line paper feed
[Code]
<1B>H <64>H n
[Range]
0 ≤ n ≤ 255
[Outline]
This command feeds the paper by n-lines after printing the one line worth of data saved in
the print buffer.
ESC i
(iDP3551 Only)
[Function]
Full cut
[Code]
<1B>H<69>H
[Outline]
This command fully cuts the paper.
ESC m
(iDP3551 Only)
[Function]
Partial cut
[Code]
<1B>H<6D>H
[Outline]
This command partially cuts the paper.
104
CITIZEN
iDP3550/3551 User’s Manual
ESC "p" m n1 n2
[Function]
Specifying the pulse generation
[Code]
<1B>H <70>H m n1 n2
[Range]
0≤m≤1
0 ≤ n1 ≤ n2 ≤ 255
[Outline]
This command outputs the signals specified with n1 and n2 to the connector pins.
m
0
1
Connector Pin
Drawer kick connector No. 2 pin
Drawer kick connector No. 5 pin
The ON time is n1×2 mS and the OFF time is n2×2 mS.
[Caution]
The user should consider driving the drawer at the following duty ratio.
ON time ÷ (ON time + OFF time) ≤ 0.2
(It is recommended to make n2 four times higher or more than n1.)
The drawer kick-out solenoid should have a resistance value of 36Ω or more. Do not use a
lower one because an overcurrent will flow.
For the drawer power, be sure to use the
printer power (Drawer kick-out connector No. 4 pin).
105
CITIZEN
iDP3550/3551 User’s Manual
ESC "r" n
[Function]
Selecting the printing color
[Code]
<1B>H <72>H n
[Range]
n = 0, 1
[Outline]
This command selects a print color for each line.
1 selects red.
[Default]
Setting n = 0 selects black.
Setting n =
The command is valid only when it is entered at the head of the line.
n = 0 (Black print)
ESC "t" n
[Function]
Selecting the character code table
[Code]
<1B>H <74>H n
[Range]
0 ≤ n ≤ 255
[Outline]
This command selects Page-n of Character Code Table.
[Default]
Depends on DIP switch setting.
n
0
1
2
3
4
5
Character Code Table
Code Page 437 (U.S.A.)
Katakana
Code Page 850 (Multilingual)
Code Page 860 (Portuguese)
Code Page 863 (Canadan-French)
Code Page 865 (Nordic)
N
6
7
8
9
255
106
Character Code Table
Code Page 852 (Eastern Europe)
Code Page 866 (Russian)
Code Page 857 (Turkish)
Windows Code
Space Page (For user setting)
CITIZEN
iDP3550/3551 User’s Manual
ESC "u" n
[Function]
Sending the status for peripheral device
[Code]
<1B>H <75>H n
[Range]
n=0
[Outline]
This commands sends the status of the connector No. 3 pin.
n
0
Connector Pin
Drawer kick-out connector No. 3 pin
Status Sent
[Caution]
Value
Bit
Function
0
1
2
3
4
5
6
No. 3 pin's level
Undefined
Undefined
Undefined
Undefined
Undefined
Undefined
0
“LOW”
1
“HIGH”
This command is valid only for the serial interface.
connector, the bit 0 will be always "1".
If nothing is connected to the
In case of DTR/DSR control, if the host cannot
receive (DSR signal has the Mark status), the printer will wait until it will be ready to
receive.
In case of XON/XOFF control, only one byte will be sent without confirming the
status of the DSR signal.
Note that it may take time to send the status after receiving the
command.
107
CITIZEN
iDP3550/3551 User’s Manual
ESC "v"
[Function]
Sending the printer status
[Code]
<1B>H <76>H
[Outline]
This command sends the printer status.
[Caution]
This command is valid only for the serial interface. The following table lists the status sent.
In case of DTR/DSR control, only one byte will be sent after confirming that the host is
ready to receive (DSR signal has the Space status).
The status at command processing time is sent after processing the data received prior to this
command.
If the printing is under way when the command is being processed, however,
the then status will be sent after completing print feed of that line.
Therefore, it may take
time to send the status after receiving the command.
Bit
Function
0
1
2
3
4
5
6
Paper near end
Undefined
Paper end
Undefined
Undefined
Undefined
Undefined
Value
108
0
With paper
1
Near end
With paper
End
0 stationary
−
CITIZEN
iDP3550/3551 User’s Manual
ESC
"{ " n
[Function]
Specifying/Canceling the inverted character print
[Code]
<1B>H <7B>H n
[Range]
0 ≤ n ≤ 255
[Outline]
This command selects/deselects inverted print.
n
0
1
n is valid only for the least significant bit.
Type
Deselects the inverted characters.
Selects the inverted characters.
[Caution]
This command is valid only if entered at the head of the line.
[Default]
n=0
<Example>
When Inverted Print
Deselected
Is
When Inverted Print Is
Selected
Print
Direction
ESC "⁄" n "data" CR or LF
[Function]
Defining the message
[Code]
<1B>H <2F>H n “data” CR or LF
[Range]
1 ≤ n ≤ 10
[Outline]
This command defines up to a 50-byte message in one line.
If the value of n is specified
beyond the range, the data following n will be treated as the print data.
Once the message is defined, it remains valid until it is redefined.
with CR (0DH) or LF (0AH).
The data should end
If the data exceeds 50 bytes, the subsequent data will be
treated as the print data.
Once the message is defined, it remains valid until it is redefined or the download deletion
command (ESC DC2 n1 n2) is executed.
109
CITIZEN
iDP3550/3551 User’s Manual
ESC DC3 n
[Function]
Printing the message
[Code]
<1B>H <13>H n
[Range]
1 ≤ n ≤ 10
[Function]
This command prints a message.
If the value of n is specified beyond the range, or if the
message is not registered yet the message will not be printed.
ESC "y" n
(Friction feed model)
[Function]
Setting the print lines after paper near end detection
[Code]
<1B>H<79>H n
[Range]
0 ≤ n ≤ 255
[Outline]
This command sets the number of print lines after paper near end detection.
It stops
printing after printing n × 2 lines since detection of the paper near end, resulting in the paper
near end state (See 4.12 Operation Panel and Display of Error).
The PE signal (parallel
interface only) changes when the paper near end is detected.
[Caution]
This command is only valid if the paper near end is selected with ESC c4 n, the command to
select the paper near end sensor valid for print stop.
[Default]
n=0
110
CITIZEN
iDP3550/3551 User’s Manual
ESC DC2 n1 n2
[Function]
Deleting the download character, message, bit image
[Code]
<1B>H <12>H n1 n2
[Range]
0 ≤ n1 ≤ 3
0 ≤ n2
(Specify 0 at n1 = 0)
(1 ≤ n2 ≤ 10 at n1 = 1)
(32 ≤ n2 ≤ 224 at n1 = 2)
(Specify 0 at n1 = 3)
[Outline]
This command deletes the downloaded characters, message, and bit image.
n1
0
1
2
3
Object Deleted
All(Message, characters, bit image)
Download message
Download characters
Download bit image
With n2, specify which data of the function specified with n1 should be deleted.
n2 = 0
Deletes all the download function specified with n1.
n2 ≠ 0
Deletes the data downloaded at the value specified with n2 (Value specified
when saving with each download command), of the download function
specified with n1.
111
CITIZEN
iDP3550/3551 User’s Manual
GS "*" n1 n2 [d] n1 × n2 × 8
(Graphic Type)
[Function]
Defining the download bit image
[Code]
<1D>H <2A>H <n1> <n2> [<d>] n1 × n2 × 8
[Range]
1 ≤ n1 ≤ 45
0 ≤ n2 ≤ 24
Note) Take care that the number of data(n1×n2×8) is equal to or smaller than 2,048.
[Outline]
This command defines the download bit image having the dots specified n1 and n2.
The
number of horizontal dots is represented by n1×8 and that of vertical dots is represented by
n2×8, respectively.
printout.)
d denotes the number to be registered.
d denotes the bit image data.
(See a download bit image
Once the download bit image is defined, it
remains valid until it is redefined or the download deletion command (ESC DC2 n1 n2) is
executed.
112
CITIZEN
iDP3550/3551 User’s Manual
GS ⁄ m
(Graphic Type)
[Function]
Printing the download bit image
[Code]
<1D>H <2F>H m
[Range]
0 ≤ m ≤ 255
[Outline]
This command prints the bit image saved in the number specified with m.
[Caution]
If the print buffer contains the data, this command will be ignored.
If the bit image has not
been saved in the specified number, this command will be ignored.
Nothing is printed when m is other than 0, 1, 2 or 3.
113
CITIZEN
iDP3550/3551 User’s Manual
15. CHARACTER CODES TABLE
15.1
CBM (Japanese)
114
CITIZEN
iDP3550/3551 User’s Manual
15.2
CBM (International)
115
CITIZEN
iDP3550/3551 User’s Manual
15.3
Star (Japanese)
116
CITIZEN
iDP3550/3551 User’s Manual
15.4
Star (International)
117
CITIZEN
iDP3550/3551 User’s Manual
15.5
Codepage PC437 (USA, European Standard)
118
CITIZEN
iDP3550/3551 User’s Manual
15.6
Codepage Katakana (Japanese)
119
CITIZEN
iDP3550/3551 User’s Manual
15.7
Codepage PC850 (Multilingual)
120
CITIZEN
iDP3550/3551 User’s Manual
15.8
Codepage PC860 (Portuguese)
121
CITIZEN
iDP3550/3551 User’s Manual
15.9
Codepage PC863 (Canadian-French)
122
CITIZEN
iDP3550/3551 User’s Manual
15.10 Codepage PC865 (Nordic)
123
CITIZEN
iDP3550/3551 User’s Manual
15.11 Codepage PC852 (Eastern Europe)
124
CITIZEN
iDP3550/3551 User’s Manual
15.12 Codepage PC866 (Russian)
125
CITIZEN
iDP3550/3551 User’s Manual
15.13 Codepage PC857 (Turkish)
126
CITIZEN
iDP3550/3551 User’s Manual
15.14 Windows Codepage
127
CITIZEN
iDP3550/3551 User’s Manual
15.15 International Character Codes Table
128
CITIZEN
iDP3550/3551 User’s Manual
APPENDIX 1. BLOCK DIAGRAM
OSC16MHz
Parallel
(CENTRONICS
Compliant)
Serial
Winder
Control
Interface
(RS-232C Compliant)
(Option)
Cutter
Control
Paper Near
End
Control
CPU
Drawer
Control
Operation
Panel
Auto
Cutter
(iDP3551 only)
Drawer
DIP Switch
Print Head
Driver
Printer
Mechanism
DP-654C
or
DP-657G
Winder
ROM
DC Motor/
LF Solenoid/
CC Solenoid/
Drivers
RAM
Battery
Back-up
Mechanism
Control
Signals/
PE Signal
Reset
Vp
Filter
Vcc
Power
Supply
Power Supply
120 V AC, 50/60 Hz
230 V AC, 50/60 Hz
129
CITIZEN
iDP3550/3551 User’s Manual
APPENDIX 2. OUTLINE DRAWING for iDP3550
Unit: mm
130
CITIZEN
iDP3550/3551 User’s Manual
APPENDIX 3. OUTLINE DRAWING for iDP3551
131
CITIZEN
iDP3550/3551 User’s Manual
<<< German >>>
132
CITIZEN
iDP3550/3551 User’s Manual
<VORSICHT>
1. Bitte lesen Sie die Bedienungsanleitung vor dem Betrieb des Geräts aufmerksam durch und bewahren Sie die
Anleitung anschließend für späteres Nachschlagen an einem sicheren Platz au f.
2. Änderungen des Inhalts dieser Anleitung bleiben ohne Vorankündigung vorbehalten.
3. Die Vervielfältigung dieser Bedienungsanleitung ohne vorherige Genehmigung verstößt, auch auszugsweise,
gegen das Urheberschutzrecht.
4. Niemals versuchen, in dieser Anleitung nicht erwähnte Geräteteile eigenhändig zu warten, zerlegen oder zu
reparieren.
5. Bitte beachten Sie, daß wir keinerlei Haftung für Schäden übernehmen, die auf unsächgemäße Bedienung,
falsche Handhabung oder eine ungeeignete Betriebsumgebung zurückzuführen sind.
6. Zur Vermeidung von Unfällen und sonstigen Problemen
ist das Gerät ausschließlich auf die in der
Bedienungsanleitung beschriebene Weise zu betreiben.
7. Daten sind grundsätzlich temporär, d.h. sie können nicht permanent gesichert oder über längere Zeit gespeichert
werden. Es sei deshalb darauf hingewiesen, daß wir für finanzielle Schäden oder Profitrückgänge als Folge von
Datenverlust, Unfällen, Reparaturen, Tests usw. keinerlei Haftung übernehmen.
8. Bitte wenden Sie sich mit Fragen oder Hinweisen auf Fehler oder Auslassungen im Text dieser Anleitung an
unsere Geschäftsstelle.
9. Beachten Sie jedoch, daß wir, ungeachtet des obigen Punkts 8, keinerlei Haftung für negative
Folgeerscheinungen im Zusammenhang mit dem Betrieb dieses Geräts übernehmen.
Patersstraat 106-108
2300 Turnhout
Tel:014/42.55.99
Fax: 014/42.32.64
BTW BE 0415.638.961
Rek: 230-0026460-96
info@vanmechelen.be
www.vanmechelen.be
133
CITIZEN
iDP3550/3551 User’s Manual
ZU BEACHTENDE SICHERHEITSMASSREGELN
Zur Vermeidung von Gefahren gegenüber dem Bediener und anderen Personen und Sachschäden sind die folgenden
Vorsichtsmaßregeln unbedingt zu beachten.
• Der folgende Text beschreibt das Ausmaß der Gefahren und potentiellen Sachschäden, die durch eine
Mißachtung der Bedienungshinweise oder durch die unsachgemäße Handhabung des Geräts entstehen
können.
WARNUNG
Die Mißachtung dieser Vorsichtsmaßregel kann zu Körperverletzungen mit
möglicher Todesfolge führen.
VORSICHT
Die Mißachtung dieser Vorsichtsmaßregel kann zu Körperverletzungen oder
Sachschäden führen.
Dieses Symbol ruft den Bediener zu erhöhter Wachsamkeit auf.
Dieses Symbol weist auf wichtige Informationen, wie z.B. Bedienungsschritte oder dergleichen, hin.
134
CITIZEN
iDP3550/3551 User’s Manual
WARNUNG
• Beim Betrieb des Geräts sind die nachfolgenden Vorsichtsmaßregeln unbedingt zu beachten. Eine
Mißachtung dieser Hinweise kann zu Schäden, Funktionsstörungen, Rauchentwicklung und Brandgefahr
durch Überhitzen und zu elektrischen Schlägen führen.
Der fortgesetzte Betrieb des Geräts in anormalem Zustand, wie z.B. nach einer Beschädigung, kann
Funktionsstörungen, Rauchentwicklung, fremde Gerüche/Geräusche und Brände verursachen. Bei
anormalem Betriebszustand das Gerät sofort ausschalten und an einen Fachhändler wenden. Niemals
versuchen, das Gerät eigenhändig zu reparieren, um ernsthafte Gefahren zu vermeiden.
• Das Gerät vor starken Stößen und Erschütterungen, wie z.B. Tritte, Stampfen, Schläge, Herunterfallen
usw., schützen.
• Das Gerät an einem gut belüfteten Platz aufstellen, und darauf achten, die Belüftungsöffnung nicht zu
blockieren.
• Bei der Aufstellung des Geräts Plätze vermeiden, an denen chemische Reaktionen auftreten, wie z.B. in
einem Labor, sowie Plätze mit salz- oder gashaltiger Umgebungsluft.
• Netz- und Datenkabel niemals am Kabel haltend anschließen oder abziehen. Bei Betrieb, Verrücken
oder Tragen des Geräts darauf achten, daß die Kabel keiner Gewalteinwirkung ausgesetzt sind.
• Darauf achten, daß keine Fremdköper, wie z.B. Nadeln oder Büroklammern, in das Gerät gelangen.
• Darauf achten, keine Flüssigkeiten auf dem Gerät zu vergießen oder chemische Substanzen enthaltende
Sprays darüber zu versprühen. Bei versehentlichem Naßwerden das Gerät sofort ausschalten, das
Stromanschlußkabel abziehen, das Netzkabel von der Steckdose trennen usw. und an einen Fachhändler
wenden.
• Das Gerät niemals eigenhändig zerlegen oder modifizieren. Eine Mißachtung dieser Vorsichtsmaßregel
kann zu Bränden und elektrischen Schlägen führen.
• Sollte unbeabsichtigt Wasser in das Gerät eindringen, sofort den Netzstecker abziehen und an einen
Fachhändler wenden. Der fortgesetzte Betrieb in diesem Zustand kann zu Bränden und elektrischen
Schlägen führen.
• Das Gerät ausschließlich mit der vorgeschriebenen Netzspannung betreiben. Eine Mißachtung dieser
Vorsichtsmaßregel kann Brände, elektrische Schläge und Funktionsstörungen verursachen.
• Beschädigen Sie das Netzkabel nicht, indem Sie es brechen, verbiegen, verändern, extrem verdrehen,
ziehen oder bündeln. Vermeiden Sie es auch, schwere Gegenstände auf das Netzkabel zu stellen oder es
zu erhitzen. Dadurch kann das Netzkabel beschädigt werden was dann u.U. zu Bränden, elektrischen
Schlägen oder Fehlfunktionen führt. Sollte das Netzkabel beschädigt worden sein, wenden Sie sich an
Ihren Fachhändler.
• Stecken bzw. entfernen Sie das Netzkabel nicht mit nassen Händen in die bzw. von der Steckdose. Es
besteht sonst die Gefahr von elektrischen Schlägen.
• Das Netzteil niemals mit nassen Händen anschließen oder trennen. Hierdurch können Brände,
elektrische Schläge und sonstige Probleme entstehen.
• Verpackungsbeutel sind vorschriftsgemäß zu entsorgen oder ansonsten von Kindern fernzuhalten.
Kleinkinder können durch Überstreifen eines Plastikbeutels ersticken.
135
CITIZEN
iDP3550/3551 User’s Manual
VORSICHTSMASSREGELN FÜR DIE AUFSTELLUNG
• Das Gerät nicht an Plätzen abstellen oder betreiben, an denen es Feuer, Feuchtigkeit oder direkter
Sonnenbestrahlung ausgesetzt ist. Ebenso sind Plätze in der Nähe von Heizkörpern und sonstigen
Wärmenquellen zu vermeiden, an denen Umgebungstemperatur und Luftfeuchtigkeit nicht den
vorgeschriebenen Betriebsbedingungen entsprechen, sowie Plätze, an denen das Gerät Öl, Metallspänen oder
Staub ausgesetzt ist. Andernfalls können Funktionsstörungen sowie Rauch- und Brandentwicklung die Folge
sein.
• Bei der Aufstellung des Geräts Plätze vermeiden, an denen chemische Reaktionen auftreten, wie z.B. in
einem Labor, sowie Plätze mit salz- oder gashaltiger Umgebungsluft. Hierbei besteht die Gefahr von
Bränden und elektrischen Schlägen.
• Keine schweren Gegenstände auf den Drucker stellen, um mögliche Probleme zu vermeiden.
• Das Gerät nicht in der Nähe eines Radios oder Fernsehers verwenden und nicht zusammen mit einem Radio
oder Fernseher an die gleiche Steckdose anschließen. Hierdurch können Empfangsstörungen auftreten.
• Das Gerät ausschließlich mit der vorgeschriebenen Netzspannung und -frequenz betreiben. Eine Mißachtung
dieser Vorsichtsmaßregel kann Brände, elektrische Schläge und Funktionsstörungen verursachen.
• Vergewissern, daß die für den Anschluß des Netzkabels verwendete Steckdose über eine ausreichende
Kapazität verfügt.
• Darauf achten, eine einzelne Steckdose nicht durch den Anschluß des Netzkabels zu überlasten. Andernfalls
können Brände und Stromausfälle die Folge sein. Darüber hinaus nicht fest auf das Netzkabel treten oder
schwere Gegenstände darauf abstellen.
• Erdungskabel niemals an ein Gasrohr anschließen, da hierbei Explosionsgefahr besteht. Vor dem
Anschließen oder Trennen eines Erdungskabels unbedingt zuerst den Netzstecker aus der Steckdose ziehen.
• Beim Anschließen oder Trennen der Kabel zuerst die Netzversorgung ausschalten, einschließlich der
angeschlossenen Seite, und dann an Stecker und Steckdose haltend anschließen bzw. trennen. Bei einem
Transport des Geräts darauf achten, daß das Kabel keinem Zug ausgesetzt ist.
• Steckerkabel sind fest anzuschließen. Durch Anschluß mit umgekehrter Polarität können Innenbauteile oder
Paßflächen beschädigt werden.
• Für Datensignalleitungen abgeschirmte Kabel oder verzwirbelte Doppeladerkabel verwenden, um
Rauschstörungen möglichst gering zu halten. Der Anschluß an ein Rauschstörungen erzeugendes Gerät ist
zu vermeiden.
• Falls ein Geldschubladen-Ausschubmechanismusstecker vorhanden ist, sollten keine anderen Vorrichtungen, die
nicht den vorgeschriebenen Solenoidspezifikationen entsprechen, angeschlossen werden. Eine Mißachtung dieser
Vorsichtsmaßregel kann zu Fehlfunktionen führen.
• Das Gerät an einem Platz in der Nähe einer Steckdose betreiben, wo sich der Netzstecker zum Unterbrechen
der Stromversorgung jederzeit schnell und mühelos abziehen läßt.
• Das Netzkabel aus der Steckdose ziehen, wenn das Gerät längere Zeit lang nicht benutzt werden soll.
• Vor einem Transport die Papierrolle aus dem Gerät herausnehmen.
• Das Gerät auf einer ebenen, stabilen Tischplatte an einem gut belüfteten Platz und frei von Erschütterungen
aufstellen. (Darauf achten, die Belüftungsöffnung nicht zu blockieren.)
136
CITIZEN
iDP3550/3551 User’s Manual
VORSICHTSMASSREGELN FÜR DIE HANDHABUNG
Zur Vermeidung von Problemen sind bei der Handhabung des Geräts die folgenden Vorsichtsmaßregeln zu
beachten.
• Für die Stromversorgung ausschließlich das vorgeschriebene Netzteil verwenden.
• Den Druckbetrieb nicht ohne eingelegtes Papier oder ohne Farbband starten, da hierdurch der
Druckkopf beschädigt werden kann.
• Darauf achten, daß keine Fremdköper, wie z.B. Nadeln, Büroklammern oder Schrauben, in das
Gehäuse gelangen.
• Darauf achten, keine Flüssigkeiten auf dem Gerät zu vergießen oder chemische Substanzen enthaltende
Sprays darüber zu versprühen.
• Das Gerät vor starken Stößen und Erschütterungen bewahren und nicht fallen lassen.
• Niemals mit spitzen Objekten, wie z.B. einem Kugelschreiber, auf das Bedienfeld drücken.
• Papierblätter niemals zum fortlaufenden Drucken mit Klebestreifen zusammenkleben.
• Ein bereits eingezogenes Blatt niemals gewaltsam herausziehen. Beim Öffnen/Schließen der
Druckerabdeckung darauf achten, daß sich das Papier nicht verfängt.
Zur Vermeidung vonVerletzungen und Schäden
• Den druckenden Abschnitt des Druckkopfes nicht berühren.
• Bei Einschalten keine beweglichen Teile, wie z.B. Schneidklinge und Zahnrad im Druckergehäuse,
oder elektrische Teile berühren.
• Darauf achten, körperliche Verletzungen und die Beschädigung anderer Objekte durch scharfe Kanten
zu vermeiden.
• Bei Auftreten jeglicher Störungen während des Betriebs den Drucker sofort ausschalten, und das
Netzkabel aus der Steckdose ziehen.
• Die Beseitigung von Betriebsstörungen ist qualifiziertem Fachpersonal zu überlassen. Niemals
versuchen, das Gerät eigenhändig zu zerlegen.
• Beim Öffnen/Schließen der Druckerabdeckung darauf achten, nicht die Hand oder Finger am Drucker
einzuklemmen.
137
CITIZEN
iDP3550/3551 User’s Manual
TÄGLICHE WARTUNG
• Vor der Wartung zuerst den Drucker ausschalten.
• Schmutz und Staub mit einem trockenen, weichen Tuch vom Druckergehäuse abwischen. Bei starker
Verschmutzung einen Lappen in Wasser anfeuchten, auswringen und damit abwischen. Hierzu niemals
flüchtige organische Lösungsmittel, wie z.B. Alkohol, Terpentin, Trichlorethan, Benzol, Keton oder
chemische Staubentfernungsmittel, verwenden.
• Papierstaub mit einer weichen Bürste vom Gehäuse entfernen.
138
CITIZEN
iDP3550/3551 User’s Manual
4.
4.1
BETRIEB
Druckerabdeckung Aufsetzen, Entfernen
1. Benutzen Sie beide Hände, um die Aussparungen an jeder Seite der Druckerabdeckung anzufassen und
sie anzuheben. Heben Sie die Druckerabdeckung in Pfeilrichtung an, um sie zu entfernen.
2. Wollen Sie die Druckerabdeckung wieder aufsetzen, setzen Sie die Halterung der Druckerabdeckung
vorne in den Drucker ein und senken Sie die Abdeckung auf den Drucker ab.
Aussparung
4.2
Anschluß des Schnittstellenkabels
1. Den Drucker ausschalten. (Einschließlich Kontaktseite)
2. Den Stecker korrekt ausrichten und an die Schnittstellenbuchse anschließen.
3. Den Kabelstecker an der Buchse befestigen.
Serienschnittstelle
: Die Steckerschrauben eindrehen.
Parallelschnittstelle
: Die Klemmen andrücken.
4. Das Schnittstellenkabel an den Computer anschließen.
Serienschnittstellenkabel
Serienschnittstellenbuchse
Parallelschnittstellenbuchse
Steckerklemme
Parallelschnittstellenkabel Schnittstelle
139
CITIZEN
iDP3550/3551 User’s Manual
4.3
Anschluß des Schubladenausschubsteckers
1. Das Gerät ausschalten.
2. Prüfen Sie die Ober- und Unterseite des Anschlusses für den Schubladenausschubstecker und schließen
Sie ihn an den Anschluß des Schubladenausschubsteckers am unterenTeil des Druckers an.
3. Schrauben Sie das Erdungskabel der Schublade an den Erdungsanschluß an, den Sie am unteren Teil des
Druckers sehen.
VORSICHT :
Nur den vorgeschriebenen Lade-(Magneten) an den Laden-Auszugstecker anschließen.
Schubladenausschubbuchse
Schubladenausschubstecker
Erdungsanschluß
4.4
Öffnen/Schließen des automatischen Schneidemechanismus (iDP3551)
1. Halten Sie den automatischen Schneidemechanismus fest, während Sie den Feststellhebel drücken.
Drehen Sie den Schneidemechanismus in die angezeigte Richtung, um ihn zu öffnen.
2. Wenn Sie den automatischen Schneidemechanismus schließen, prüfen Sie, ob der Feststellhebel sicher
eingerastet ist.
VORSICHT:
Den automatischen Schneidemechanismus behutsam schließen, um Stöße zu vermeiden.
Feststellhebel
Automatischer
Schneidemechanismus
140
CITIZEN
iDP3550/3551 User’s Manual
4.5
Einlegen der Farbbandkassette
1. Stellen Sie sicher, daß der Netzschalter des Druckers ausgeschaltet ist.
2. Entfernen Sie die Druckerabdeckung.
3. Öffnen Sie den automatischen Schneidemechanismus. (iDP3551)
4. Sollte sich eine Schlaufe des Farbbandes gebildet haben, drehen Sie den Knopf auf der Farbbandkassette
in Pfeilrichtung, um das Farbband zu straffen, bevor Sie es in den Drucker einsetzen.
5. Legen Sie das Farbband zwischen Druckkopf und Farbbandführung ein. Drücken Sie die Halteklemmen
in die Halter des Druckers. Sie werden ein Klicken hören.
6. Drehen Sie den Knopf der Farbbandkassette in die durch den Pfeil angezeigte Richtung, um eventuelle
Schlaufen des Bandes zu beseitigen.
7. Um die Farbbandkassette zu entfernen, heben Sie sie an, während Sie gleichzeitig die Halteklemmen
nach innen drücken. Die Halteklemmen befinden sich auf beiden Seiten.
8. Schließen Sie den automatischen Schneidemechanismus. (iDP3551)
9. Setzen Sie die Druckerabdeckung wieder auf.
VORSICHT: • Den automatischen Schneidemechanismus vorsichtig schließen.
: Farbband hier einlegen
Druckkopf
Farbbandkassette
Farbband
Knopf
Halteklemme
141
CITIZEN
iDP3550/3551 User’s Manual
4.6
Einlegen des Papiers
4.6.1 Einlegen des Papierrolls (iDP3550F/iDP3551)
1. Das Ende der Papierrolle im rechten Winkel abschneiden.
VORSICHT: • Ausschließlich die vorgeschriebene Papiersorte verwenden.
• Die Verwendung anderer Papiersorten kann zu verminderter Druckqualität, verkürzter
Betriebslebensdauer des Druckers u. dergl. führen.
• Das in den Drucker einzuführende Papierende darf nicht geknickt oder eingerissen sein.
2. Prüfen Sie die Wickelrichtung der Papierrolle.
Gut
Schlecht
Schlecht
Schlecht
3. Öffnen Sie den Papierhalter und legen Sie die Papierrolle ein, so daß sie von dem Papierhalter sicher
geführt wird.
4. Den Drucker einschalten.
5. Das Papierrollenende gerade in die
Papiereinzugöffnung (markiert durch einen Pfeil) einführen.
6. Das Papier wird automatisch eingezogen und tritt am Papierauslauf des Druckers aus (Papierauslauf des
automatischen Schneidemechanismus für den iDP3551).
Sie können überschüssiges Papier an der Papierabreißkante abreißen.
VORSICHT: • Lockeres Papier straffwickeln.
• Das Papier während des Druckens nicht festhalten, da hierdurch Papierstaus entstehen
können.
• Den automatischen Schneidemechanismus vorsichtig schließen, um Stöße zu vermeiden.
Papiereinzugsöffnung
Papierhalter
142
CITIZEN
iDP3550/3551 User’s Manual
4.6.2 Verwendung von Endlos-papier (iDP3550P)
Anfangseinstellung
1. Die Druckerabdeckung entfernen.
2. Die Druckseite des Papiers nach unten weisend in die Papierfü hrungeinlegen.
3. Wenn die Position des Stiftrads einzustellen ist, sollte das Rad mit den Hebeln auf beiden Seiten gelö
stwerden. Dann in die entsprechende Position schieben und wieder feststellen. (Siehe die linke
Abbildung unten.)
4. Einige der Perforationslö cherdes Papiers unter die Stifte schieben, das Papier in den
Druckermechanismus schieben und den Papierzufuhrknopf drehen, bis der Papieranfang die
Druckrolle erreicht. (Siehe die rechte Abbildung unten.)
Allgemeine Verwendung
1. Die Druckseite des Papiers nach unten weisend in die Papierfü hrungeinlegen.
2. Einige der Perforationslö cherdes Papiers unter die Stifte schieben, das Papier in den
Druckermechanismus schieben und den Papierzufuhrknopf drehen.
Platte
Knopf
Gesperrt
Zahnrades
(Stiftred)
Frei
Knopf
143
CITIZEN
iDP3550/3551 User’s Manual
Handhabung des Endlos-papiers
1. Mit dem Gerät iDP3550P Kann Endlos-papier mit einer Breite von 3 bis 3.5 Zoll
verwendet werden.
2. Die Position des Zahnrades (Stiftrad) bei Einlegen des Papiers entsprechend auf die Breite
einstellen.
3. Nach dem Einlegen des Papiers sollte es auf die Markierung auf der Druckrolle angeglichen
werden.
VORSICHT: • Sicherstellen, daß das vorgeschriebene Endlos-papier verwendet wird.
• Die Verwendung von anderem als dem vorgeschriebenen Endlos-papier kann die
Druckqualität, die Druckerverwendungsdauer usw. Negativ beeinflussen.
4. Die Stiftradlöcher von Endlos-papier mit einer Breite 3 Zoll können 6.35 mm oder 5 mm von
der Papierkante entfernt sein.
Bitte die folgenden Punkte bein Einlegen des 3 Zoll breiten Endlos -papiers beachten.
VORSICHT: • 6.35 mm Abstand
Wenn Endlos-papier verwendet wird, dessen Stiftradlöcher 6.35 mm von der Papierkante
entfernt sind, sollten die Kanten mit der Papierführung des Druckers angeglichen werden.
Da die Kanten des bedrunkten Bereichs in der Nähe der Stiftradlöcher sind, sollte
sichergestellt werden, daß das Papier richtig eingelegt ist.
• 5 mm Abstand
Wenn Endlos-papier verwendet wird, dessen Stiftradlöcher 5 mm von der Papierkante
entfernt sind, sollten die Stifte des Stiftrads auf die Stiftradlöcher angepaßt und dann der
Knopf gedreht werden. Bitte beachten, daß in diesem Fall eine Lücke zwischen den
Papierkanten und der Papierführung des Druckers vorhanden ist.
5. Endlos-papier mit runden Löchern verwenden.
6. Wenn mehrere Seiten Endlos-papier verwendet werden, sollte die perforierte Linie des
Randes innerhalb von 5 mm der Papierseite liegen.
144
CITIZEN
iDP3550/3551 User’s Manual
4.7
Hintere Abdeckung des Druckers aufsetzen
Setzen Sie die Klammern der hinteren Druckerabdeckung in die rechteckigen Löcher an der Rückseite des
Druckers ein und schließen Sie die hintere Abdeckung in die durch den Pfeil angezeigte Richtung.
Rechteckige Löcher
Hintere Druckerabdeckung
4.8
Anbringen des Papierhalters (iDP3550P)
1) Papierhalterkapazität
Der Papierhalter kann Endlospapier mit einer Breite bis zu 3.5 Zoll und einer Dicke bis zu
40 mm aufnehmen.
2) Anbringen desPapierhaiters
Die Haken des Papierhalters in die rechteckigen …ffnungen auf der Rÿckseite des Druckers
einsetzen und dann den Papierhaiter in Pfeilrichtung nach unten schieben.
Rechteckige
Löcher
Papierhalter
145
CITIZEN
iDP3550/3551 User’s Manual
4.9
Herausnehmen der Restpapierrolle
4.9.1 Restpapierrolle
1. Die Druckerabdeckung öffnen.
2. Den automatischen Schneidemechanismus
(iDP3551) öffnen.
3. Entfernen Sie das Papier, indem Sie es in die Richtung
ziehen, in die es normalerweise
bewegt wird.
4. Den automatischen Schneidemechanismus
(iDP3551) schließen.
5. Setzen Sie die Druckerabdeckung wieder auf.
VORSICHT: • Wenn Sie das Papier entfernen, ziehen Sie es nicht aus der apiereinzugsöffnung.
(Entfernen Sie das Papier nicht in der entgegengesetzten Richtung.)
• Den automatischen Schneidemechanismus behutsam schließen, um Stöße zu vermeiden.
4.9.2 Endlos-papier
1. Die Druckerabdeckung entfernen.
2. Wšhrend der Knopf in Pfeilrichtung gedreht wird, das Endlos-papier wie in der Abbildung
gezeigt in Pfeilruchtung herausziehen.
146
CITIZEN
iDP3550/3551 User’s Manual
4.10
Beseitigung von Papierstaus
1. Die Druckerabdeckung öffnen.
2. Das Papier an der Papiereinzugöffnung abtrennen.
3. Den Papierfreigabehebel in Pfeilrichtung stellen. Die Papiervorschubwalze gibt hierdurch das Papier frei,
so daß der Papierstau beseitigt werden kann.
4. Jegliches im Papierweg aufgestaute Papier beseitigen.
VORSICHT: • Wenn Sie das Papier entfernen, ziehen Sie es nicht aus der Papiereinzugsöffnung.
(Entfernen Sie das Papier nicht in der entgegengesetzten Richtung.)
• Den automatischen Schneidemechanismus behutsam schließen, um Stöße zu vermeiden.
4.11
Initialisierung des Schneidemechanismus (iDP3551)
1. Entfernen Sie die Druckerabdeckung.
2. Die LF-Taste drücken. Hierdurch wird der
automatische
Automatischer
Schneidemechanismus
Notfallknopf
Schneidemechanismus
initialisiert, die Schneidklinge zurückgezogen
und der Alarm gelöscht.
3. Bei Auftreten eines Papierstaus das gestaute
Papier vollständig entfernen. Siehe hierzu 4.10
"Beseitigung von Papierstaus".
4. Falls sich der Alarm hierdurch nicht löschen
läßt, die Netzversorgung ausschalten und den
automatischen Schneidemechanismus öffnen.
5. Durch ein kleines Loch an der Rückseite des automatischen Schneidemechanismus läßt sich ein
Notfallknopf erkennen. Diesen Knopf mit einer Pinzette, einem Schraubendreher o. dergl. in die durch
den Pfeil angezeigte Richtung drehen, um die Schneidklinge zurückzuziehen. Gestautes Papier oder
Papierreste vollständig entfernen, falls vorhanden.
6. Setzen Sie die Druckerabdeckung wieder auf.
VORSICHT: • Beim Herausziehen des Papiers (in Vorwärts- oder Rückwärtsrichtung) unbedingt den
Papierfreigabehebel betätigen.
• Den automatischen Schneidemechanismus behutsam schließen, um Stöße zu vermeiden.
147
CITIZEN
iDP3550/3551 User’s Manual
4.12
Bedienfeld und Fehleranzeigen
1. Netzanzeigelämpchen (POWER) (grün)
Dieses Lämpchen leuchtet bei eingeschalteter Netzversorgung.
2. Fehlerlämpchen (ERROR) (grün)
Dieses Lämpchen leuchtet oder blinkt zur Anzeige eines Fehlers.
Fehleranzeige
ERROR-Lämpchen
Signalgeber
Mechanischer Fehler
Rasches Blinken
Etwa 1 Sekunde anhaltender
Signalton
Papierende
Blinkt (in
Drei kurze Signaltöne, in
Sekun denabständen)
Abstand von 0,6 Sekunden
wiederholt werden
Papierrolle fast leer
Blinkt (in
Drei kurze Signaltöne, in
Sekundenabständen)
Abstand von 0,6 Sekunden
wiederholt werden
Motorsperre des
Rasches Blinken
Etwa 1 Sekunde langer
Schneidemechanismus
(zweimal pro Sekunde) Signalton
(nur iDP3551)
Mechanischer Fehler
Rückstellmethode
Den Netzschalter
rückstellen.
Eine neue Papierrolle
einlegen.
Eine neue Papierrolle
einlegen.
Den Papierstau
beseitigen.
: Wenn der Druckmechanismus aufgrund eines Papierstaus o. dergl. höher als
normal belastet wird, erklint ein Signalton, und das SEL/ERROR-Lämpchen
blinkt, um den Druckmechanismus zu stoppen.
Papierende
(iDP3550F ,
iDP3551)
: Sollte das Ende der Papierrolle erreicht sein, wird das durch den
Papierrestsensor erkannt, der sich in der Nähe des Druckkopfes befindet. Es
wird ein Signalton erzeugt und das Lämpchen SEL/ERROR blinkt, um den
Druckmechanismus zu stoppen. Wird Papier in den Papierpfad eingelegt, wird
die Papierrolle geladen. (Siehe 4.6 Einlegen des Papiers)
Papiervorrat fast leer
(iDP3550F ,
iDP3551)
: Bei aufgebrauchtem Papiervorrat wird der Papierrestsensor zum Einschalten
des Signalgebers und des SEL/ERROR-Lämpchens aktiviert. Selbst nach
Erkennen des zuende gehenden Papiervorrats kann die gewünschte Anzahl von
Zeilen durch Eingegeben eines Befehls gedruckt werden. (Siehe die
Beschreibung des Befehls zum Einstellen der Druckzeilenanzahl nach der
Erkennung des zuende gehenden Papiervorrats.)
Schneidemechanismus-Motorsperre :
(nur iDP3551)
Wenn der Schneidepositionssensor in der Papierschneideeinheit bei laufendem
Schneidemotor länger als 1 Sekunde ein- oder ausgeschaltet ist, wird die
Schneide- und Druckfunktion durch Sperren des Motors ausgeschaltet.
148
CITIZEN
iDP3550/3551 User’s Manual
Pufferdaten löschen
: Ist der Drucker eingeschaltet, werden entsprechend der Funktion des
Schalters SEL, die Pufferdaten im Eingangsspeicher gelöscht, wie Sie das im
Flußdiagramm auf der nächsten Seite sehen.
Um die Pufferdaten im Eingangsspeicher zu löschen, schalten Sie den Drucker
ein, während Sie gleichzeitig den Schalter SEL drücken. Es wird die folgende
Meldung gedruckt.
“Clear Data in Buffer”
“Cleared Data in Buffer”
Um die Pufferdaten im Eingangsspeicher zu drucken, schalten Sie einfach den
Drucker ein. Es wird die folgende Meldung gedruckt und die Daten des
Eingangsspeichers werden gedruckt.
“Power Down(Data in Buffer)”
Testdruck
: Um sich einen Testdruck drucken zu lassen, schalten Sie den Drucker ein,
während Sie gleichzeitig den Schalter LF drücken.
Dumpmodus:
: Um in den Dumpmodus zu schalten, schalten Sie den Drucker ein, während
Sie gleichzeitig den Schalter LF und SEL drücken. Es wird die folgende
Meldung gedruckt.
“=== Hexadecimal Dump ===”
149
CITIZEN
iDP3550/3551 User’s Manual
Einschalten
SEL SW ?
• Das Lämpchen SEL/ERROR blinkt in Abständen
von 0,25 Sekunden.
• Ein Signalton ist 1 Sekunde lang zu hören.
ON
OFF
Pufferdaten
NEIN
JA
Es wird die Meldung „Clear
in
Data in Buffer “
vergrößerten roten Zeichen
gedruckt. Danach erfolgt ein
schneller Zeilenvorschub von
fünf Zeilen.
JA
1 Sek. vergangen
NEIN
OFF
SEL SW ?
ON
NEIN
Pufferdaten
JA
Es werden die Daten im Eingangsspeicher gelöscht
und die Meldung „Cleared Input Buffer“ gedruckt.
Danach erfolgt ein schneller Zeilenvorschub von
fünf Zeilen. Das Lämpchen SEL/ERROR leuchtet.
Es wird die Meldung „Drucker
ausschalten (Data in Buffer) in
roter Farbe gedruckt, gefolgt vom
Inhalt des Puffers. Nach dem
Ausdruck leuchtet das Lämpchen
SEL/ERROR.
Wartet auf Dateneingabe.
150
CITIZEN
iDP3550/3551 User’s Manual
4.13
Druckvorgang
Da der Druckkopf dieses Druckers nicht mit einem Temperatursensor (Thermistor)
ausgestattet ist, wird
er softwaremäßig gegen Erhitzung geschützt.
Der Drucker berechnet hierzu die Anzahl der Druckpunkte und druckt je mach Anzahl pro Zeile wie folft:
1) Bei bis zu 648 Punkten pro Zeile
Drucken in beiden Richtungen
2) Bei über 648 Punkten pro Zeile
Drucken in einer Richtung
151
CITIZEN
iDP3550/3551 User’s Manual
5.
5.1
DIP-SCHALTER-EINSTELLUNG
Lage der DIP-Schalter
1. Das Gerät ausschalten.
2. Entfernen Sie die Druckerabdeckung.
3. Der DIP-Schalter befindet sich an der Stelle, wie in der Abbildung unten gezeigt. (Nur DSW2 steht für
die serielle Schnittstelle zur Verfügung.)
152
CITIZEN
iDP3550/3551 User’s Manual
5.2
DIP-Schalter-Einstellungen
1) DIP-Schalter 1
No.
DSW1-1
DSW1-2
DSW1-3
DSW1-4
Funktion
ON
Ja
Automatische Schneideinheit
OFF
Nein
Bei Auslieferung ab Werk
ON *1
ON *2
ON *2
ON *2
Internationale Zeichen
″
″
DSW1-5
Siehe Tabelle unten
CBM Kommando
CBM2-Modus
CBM1-Modus
(iDP3530
(iDP3540
system)
system)
Siehe Tabelle unten
Graphisch
Schriftzeichen
6K Byte
256 Byte
OFF *4
DSW1-6
CR-Modus
DSW1-7
Mechanismus Typ
DSW1-8
Puffergröße
DSW1-9
Betriebsmodus
Siehe Tabelle unten
DSW1-10
″
*1, *3: Je nach Typ.
*2:
Je nach Bestimmungsort.
*4:
Nur aktiv, wenn der CBM-Modus mit Hilfe der Schalter DSW1-9 und -10
Weitere Einzelheiten siehe 13.1 „CBM-Modus“.
*5:
Beim Graphisch typ sind die DIP-Schalter auf die Position ON eingestellt.
(Diese Einstellungen ab Weak nicht Šndern.)
Internationale Zeichenwahl
eingeschaltet ist.
Zeichencode-Wahl
No. DSW1- DSW1- DSW12
3
4
Land
OFF
OFF *5
ON
OFF *3
OFF *3
ESC/POSModus
U.S.A.
ON
ON
ON
Code 437
Frankreich
Deutschland
Großbritannien
Dänemark
Schweden
Italien
Windows
Codeseite
OFF
ON
OFF
ON
OFF
ON
ON
OFF
OFF
ON
ON
OFF
ON
ON
ON
OFF
OFF
OFF
OFF
OFF
OFF
Code 850
″
″
Code 865
″
Code 850
Windows
Codeseite
CBM-Modus
Star-Modus
CBM
(international)
Code 850
″
″
Code 865
″
Code 850
Windows
Codeseite
Star
(international)
Code 850
″
″
Code 865
″
Code 850
Windows
Codeseite
Siehe internationale Zeichencode-Tabelle und Schriftzeichen-Tabelle
CR-Modus(DSW1-6)
Betriebsmodus
DSW1-9
DSW1-10
Modus
CBM
Star
OFF
CR+LF
CR+LF
ON
CR
Ignoriert
CBM
ESC/POS
Star
OFF
ON
OFF
OFF
OFF
ON
ESC/POS
CR+LF
CR
Star
Auto-Schneidfunkti
on
ON
ON
153
CITIZEN
iDP3550/3551 User’s Manual
2) DIP-Schalter 2
No.
DSW2-1
DSW2-2
DSW2-3
DSW2-4
DSW2-5
DSW2-6
DSW2-7
DSW2-8
Funktion
Bitlänge
Parität
Ungerade/Gerade
Kommunikationsmodus
Baudrate
″
″
ON
8 Bit
Nein
Ungerade
DTR/DSR
OFF
7 Bit
Ja
Gerade
XON/XOFF
Siehe Tabelle unten

Nicht verwendet

Werksseitige Einstellung
ON
ON
ON
ON
ON
ON
OFF
OFF
Baudrate
Baudrate
150
300
600
1200
2400
4800
9600
19200
DSW2-5
OFF
OFF
OFF
OFF
ON
ON
ON
ON
DSW2-6
OFF
OFF
ON
ON
OFF
OFF
ON
ON
DSW2-7
OFF
ON
OFF
ON
OFF
ON
OFF
ON
♦ Der DIP-Schalter 2 wird nur für die serielle Schnittstelle verwendet.
154
CITIZEN
iDP3550/3551 User’s Manual
6. EINSTELLUNG DER VORWAHL-JUMPERSTECKER
6.1
Lage der Vorwahl-Jumperstecker
1. Betriebsstrom ausschalten.
2. Die Vorwahl-Jumperstecker werden ab Werk, vor dem Versand eingestellt. Wollen Sie diese
Einstellungen ändern, entfernen Sie die Steuerplatine und ändern Sie die Einstellungen entsprechend den
Anweisungen des Service-Handbuches.
Die Lage der Vorwahl-Jumperstecker sehen Sie in der folgenden Abbildung.
Serielle Schnittstelle
6.2
Parallele Schnittstelle
Vorwahl-Jumperstecker-Tabelle
Einstellung der
Vorwahl-Jumperstecker
Jumperstecker Seriell
Modus
Lage
SCA
SCB
SCC
SCD
SCE
SCF
SCG
SCH
CBM
Star
ESC/POS
1-C *
1-C *
1-C
1-C
1-C *
1-C *
1-C *
1-C
2-C
1-C *
2-C
2-C
2-C
2-C
2-C
2-C *
2-C
2-C
*
*
1-C *
1-C *
1-C *
2-C *
CBM
Star
ESC/POS
1-C *
1-C
1-C *
1-C
1-C
1-C
1-C *
1-C
2-C *
2-C
2-C
2-C *
* = Offen
1-C* = 1-C oder offen
2-C* = 2-C oder offen
Parallel
Modus
Lage
SCA
SCB
SCC
SCD
1-C Einstellung
Jumperstecker
2-C Einstellung
Jumperstecker
* = Offen
1-C* = 1-C oder offen
2-C* = 2-C oder offen
155
CITIZEN
iDP3550/3551 User’s Manual
7.
METHODE FÜR MODUSEINSTELLUNG
Dieser Drucker hat die Modi CBM, Star, und ESC/POS. Jeder gewünschte Modus kann gewählt und nach
Bedarf eingestellt werden.
(1) Einstellmethode
• Siehe 5. DIP-SCHALTER-EINSTELLUNG
• Unter bezug auf die Einstellungen der DIP-Schalter-Segmente 1-9 und 1-10 und die der
Vorwahl-Jumperstecker jeden Modus einstellen.
156
CITIZEN
iDP3550/3551 User’s Manual
12. WARTUNG UND DIENST
Bitte wenden Sie sich an die folgenden Stellen für weitergehende Informationen.
Nordamerika
Andere Gebiete
CBM America Corporation
Japan CBM Corporation
Service Center
Information Systems Division
365 Van Ness Way
CBM Bldg., 5-68-10, Nakano
Suite 510
Nakano-ku, Tokyo 164-0001
Torrance, CA 90501, USA
Japan
TEL +1-310-781-1460
TEL +81-3-5345-7540
FAX +1-310-781-9157
FAX +81-3-5345-7541
Patersstraat 106-108
2300 Turnhout
Tel:014/42.55.99
Fax: 014/42.32.64
157
BTW BE 0415.638.961
Rek: 230-0026460-96
info@vanmechelen.be
www.vanmechelen.be
CITIZEN
Information Systems Division
CBM Bldg., 5-68-10, Nakano, Nakano-ku, Tokyo 164-0001, Japan
Head Office
Tel: (+81-3) 5345-7540 Fax: (+81-3) 5345-7541
09E-20000401-0092-0176-04.15 Printed in Japan
Download PDF
Similar pages