Installing printer driver for Macintosh

This manual is provided for information purposes only. All information included herein is subject to change without notice. Xerox Corporation is not responsible
for any changes, direct or indirect, arising from or related to use of this manual.
© 2008 by Xerox Corporation. All rights reserved.
• Phaser 3435, and Phaser 3435/DN are trademarks of Xerox Corporation.
• Xerox and Xerox logo are trademarks of Xerox Corporation.
• Centronics is a trademark of Centronics Data Computer Corporation.
• IBM and IBM PC are trademarks of International Business Machines Corporation.
• PCL and PCL 6 are trademarks of Hewlett-Packard company.
• Microsoft, Windows, Windows 2000, Windows NT 4.0, Windows XP, and Windows 2003 are registered trademarks of Microsoft Corporation.
• PostScript 3 is a trademark of Adobe System, Inc.
• UFST® and MicroType™ are registered trademarks of Agfa division of Bayer Corp.
• TrueType, LaserWriter, and Macintosh are trademarks of Apple Computer, Inc.
• All other brand or product names are trademarks of their respective companies or organizations.
CONTENTS
1. Introduction
Special features ......................................................................................................................................................
Printer overview ......................................................................................................................................................
Understanding the Status LED ................................................................................................................................
Finding more information ........................................................................................................................................
1.1
1.2
1.4
1.4
2. System setup
Using control panel menus ......................................................................................................................................
Menu overview ........................................................................................................................................................
Printing a demo page ..............................................................................................................................................
Changing the display language ...............................................................................................................................
Using toner save mode ...........................................................................................................................................
2.1
2.1
2.7
2.7
2.7
3. Software overview
Supplied software .................................................................................................................................................... 3.1
Printer driver features .............................................................................................................................................. 3.2
System requirements .............................................................................................................................................. 3.2
4. Network setup
Introduction .............................................................................................................................................................
Supported operating systems .................................................................................................................................
Configuring TCP/IP .................................................................................................................................................
Configuring EtherTalk .............................................................................................................................................
Setting Ethernet speed ............................................................................................................................................
Restoring the network configuration ........................................................................................................................
Printing a network configuration page .....................................................................................................................
Configuring 802.1x ..................................................................................................................................................
Configuring CentreWare IS .....................................................................................................................................
4.1
4.1
4.2
4.2
4.2
4.2
4.3
4.3
4.3
5. Loading print media
Selecting print media ............................................................................................................................................... 5.1
Loading paper ......................................................................................................................................................... 5.4
Selecting an output location .................................................................................................................................... 5.8
6. Basic printing
Printing a document ................................................................................................................................................ 6.1
Canceling a print job ............................................................................................................................................... 6.1
7. Ordering supplies and accessories
Print cartridges ........................................................................................................................................................ 7.1
Accessories ............................................................................................................................................................. 7.1
How to purchase ..................................................................................................................................................... 7.1
8. Maintenance
Printing information page ........................................................................................................................................
Cleaning the printer .................................................................................................................................................
Maintaining the print cartridge .................................................................................................................................
Maintenance parts ...................................................................................................................................................
8.1
8.1
8.2
8.4
9. Troubleshooting
Clearing paper jams ................................................................................................................................................ 9.1
Troubleshooting checklist ........................................................................................................................................ 9.6
Understanding display messages ........................................................................................................................... 9.6
Print cartridge-related messages ............................................................................................................................ 9.8
Solving general printing problems ........................................................................................................................... 9.9
Solving print quality problems ............................................................................................................................... 9.11
Common Windows problems ................................................................................................................................ 9.13
Common PostScript problems .............................................................................................................................. 9.13
Common Linux problems ...................................................................................................................................... 9.14
Common Macintosh problems .............................................................................................................................. 9.14
10. Installing accessories
Precautions when installing accessories ............................................................................................................... 10.1
Installing a memory DIMM .................................................................................................................................... 10.1
11. Specifications
Printer specifications ............................................................................................................................................. 11.1
Safety
Operational Safety Information
Your Xerox equipment and supplies have been designed and tested
to meet strict safety requirements. These include safety agency
examination, approval, and compliance with established
environmental standards.
Read these safety notes carefully before using this product to
ensure you operate the equipment safely.
Your Xerox product and supplies have been designed and tested to
meet strict safety requirements. These include safety Agency
approval, and compliance to established environmental standards.
Please read the following instructions carefully before operating the
product and refer to them as needed to ensure the continued safe
operation of your product.
To ensure the continued safe operation of your Xerox equipment,
follow these safety guidelines at all times:
Do These:
The safety testing and performance of this product have been
verified using Xerox materials only.
•
Always follow all warnings and instructions that are marked on
or supplied with the equipment.
•
Before cleaning this product, unplug the product from the
electrical outlet. Always use materials specifically designated for
this product, the use of other materials may result in poor
performance and create a hazardous situation.
WARNING: This WARNING mark alerts users to the
possibility of personal injury.
WARNING: This WARNING mark alerts users to
WARNING: Do not use aerosol cleaners. Aerosol
heated surfaces.
cleaners can be explosive or flammable when used
on electromechanical equipment.
CAUTION: This symbol indicates a Laser is being
used in the equipment and alerts the user to refer to
the appropriate safety information.
•
Always exercise care when moving or relocating equipment.
•
Always locate the machine on a solid support surface (not on
plush carpet) that has adequate strength to support the weight
of the machine.
•
Always locate the machine in an area that has adequate
ventilation and room for servicing.
•
Always unplug this equipment from the electrical outlet before
cleaning.
WARNING: This product must be connected to a
protective earth circuit.
Operator Accessible Areas
This equipment has been designed to provide operator access to
safe areas only. Operator access to hazardous areas is restricted
using covers or guards, which require a tool to enable removal.
Never remove these covers or guards.
NOTE: Your Xerox machine is equipped with an energy saving
device to conserve power when the machine is not in use. The
machine may be left on continuously.
Maintenance Information
CAUTION: The metallic surfaces in the fuser area
1. Any operator product maintenance procedures will be
are hot. Please use caution when removing paper
jams from this area and avoid touching any metallic
surfaces.
described in the user documentation supplied with the product.
2. Do not carry out any maintenance on this product which is not
described in the customer documentation
Do Not Do These:
WARNING: Do not use aerosol cleaners. Aerosol
cleaners can be explosive or flammable when used
on electromechanical equipment.
3. Use supplies and cleaning materials only as directed in the
•
Never use a ground adapter plug to connect the equipment to a
power outlet that lacks a ground connection terminal.
•
Never attempt any maintenance function that is not specifically
described in this documentation.
•
Never obstruct ventilation openings. They are provided to
prevent overheating.
Operator section of this manual.
4. Do not remove covers or guards that are fastened with screws.
There are no parts behind these covers that you can maintain
or service.
i
•
Never remove covers or guards that are fastened with screws.
There are no operator serviceable areas within these covers.
Electrical Supply
•
Never locate the machine near a radiator or any other heat
source.
1. This product shall be operated from the type of electrical supply
•
Never push objects of any kind into the ventilation openings.
•
Never override or "cheat" any of the electrical or mechanical
interlock devices.
•
Never place this equipment where people might step on or trip
on the power cord.
•
This equipment should not be placed in a room unless proper
ventilation is provided. Please contact your local Authorized
dealer for further information.
indicted on the product's data plate label. If you are not sure
that your electrical supply meets the requirements, please
consult a licensed electrician for advice.
WARNING: This equipment must be connected to a
protective earth circuit. This equipment is supplied
with a plug that has a protective earth pin. This plug
will only fit into an earthed electrical outlet. This is a
safety feature. If you are unable to insert the plug into
the outlet, contact a licensed electrician to replace
the outlet.
2. Always connect equipment to a correctly grounded power
Electrical Safety Information
outlet. If in doubt, have the outlet checked by a qualified
electrician.
1. The power receptacle for the machine must meet the
requirements stated on the data plate on the rear of the
machine. If you are not sure that your electrical supply meets
the requirements, please consult your local power company or
an electrician for advice.
Disconnect Device
The power cable is the disconnect device for this equipment. It is
attached to the back of the machine as a plug-in device. To remove
all electrical power from the equipment, disconnect the power cable
from the electrical outlet.
2. The socket outlet shall be installed near the equipment and
shall be easily accessible.
3. Use the power cable that is supplied with your machine. Do not
Emergency Power Off
use an extension cord or remove or modify the power cord
plug.
If any of the following conditions occur, turn off the machine
immediately and disconnect the power cable(s) from the electrical
outlet(s). Contact anauthorized Xerox Service Representative to
correct the problem:
4. Plug the power cable directly into a correctly grounded
electrical outlet. If you are not sure whether or not an outlet is
correctly grounded, consult an electrician.
5. Do not use an adapter to connect any Xerox equipment to an
The equipment emits unusual odours or makes unusual noises. The
power cable is damaged or frayed. A wall panel circuit breaker, fuse,
or other safety device has been tripped. Liquid is spilled into the
machine. The machine is exposed to water. Any part of the machine
is damaged.
electrical outlet that lacks a ground connection terminal.
6. Do not place this equipment where people might step or trip on
the power cable.
7. Do not place objects on the power cable.
8. Do not override or disable electrical or mechanical interlock
devices.
9. Do not push objects into slots or openings on the machine.
Electrical shock or fire may result.
10. Do not obstruct ventilation openings. These openings are used
to provide proper cooling to the Xerox machine.
ii
Laser Safety Information
Council Directive 2006/95/EC as amended. Approximation of the
laws of the member states related to low voltage equipment.
CAUTION: Use of controls, adjustments or
December 15, 2004:
performance of procedure other than those specified
herein may result in hazardous light exposure.
Council Directive 2004/108/EC as amended. Approximation of the
laws of the member states related to electromagnetic compatibility.
March 9, 1999:
With specific regard to laser safety, the equipment complies with
performance standards for laser product set by government,
national and international agencies as a Class 1 laser product. It
does not emit hazardous light, as the beam is totally enclosed during
all phases of customer operation and maintenance.
Council Directive 99/5/EC, on radio equipment and
telecommunications terminal equipment and the mutual recognition
of the conformity.
For Consumables
A full declaration of conformity, defining the relevant directives and
referenced standards, can be obtained from your XEROX Limited
representative.
•
NOTE: This equipment has been tested and found to comply with
•
•
•
Store all consumables in accordance with the instructions given
on the package or container.
the limits for a Class B digital device, pursuant to Part 15 of the
FCC Rules. These limits are designed to provide reasonable
protection against harmful interference in a residential installation.
This equipment generates, uses and can radiate radio frequency
energy and, if not installed and used in accordance with the
instructions, may cause harmful interference to radio
communications. However, there is no guarantee that interference
will not occur in a particular installation. If this equipment does
cause harmful interference to radio or television reception, which
can be determined by turning the equipment off and on, the user is
encouraged to try to correct the interference by one or more of the
following measures:
Keep all consumables away from the reach of children.
Never throw print cartridges or toner containers into an open
flame.
Cartridges: When handing cartridges, for example ink, fuser,
etc, avoid skin or eye contact. Eye contact can cause irritation
and inflammation. Do not attempt to disassemble the cartridge.
This can increase the risk of skin or eye contact.
Product Safety Certification
This product is certified by the following Agency using the Safety
standards listed.
Agency
Standard
Underwriters Laboratories Inc.
UL60950-1st Edition (2003) (USA/
Canada)
SEMKO
IEC60950-1st Edition 1 (2001)
This product has been manufactured under a registered ISO 9001
Quality system.
•
Reorient or relocate the receiving antenna.
•
Increase the separation between the equipment and receiver.
•
Connect the equipment into an outlet on a circuit different from
that to which the receiver is connected.
•
Consult the dealer or an experienced radio/TV technician for
help.
WARNING: Changes or modifications to this
equipment not specifically approved by the Xerox
Corporation may void the user’s authority to operate
this equipment.
Regulatory Information
WARNING: Shielded cables must be used with this
equipment to maintain compliance with FCC
regulations.
CE Mark
The CE mark applied to this product, symbolizes XEROX's
declaration of conformity with the following applicable European
Union Directives, as of the dates indicated:
December 12, 2006:
iii
OpenSSL License
ANY WAY OUT OF THE USE OF THIS SOFTWARE, EVEN IF
ADVISED OF THE POSSIBILITY OF SUCH DAMAGE.
Copyright (c) 1998-2001 The OpenSSL Project. All rights
reserved.
This product includes cryptographic software written by Eric
Young(eay@cryptsoft.com). This product includes software written
by Tim Hudson (tjh@cryptsoft.com).
Redistribution and use in source and binary forms, with or without
modification, are permitted provided that the following conditions are
met:
Original SSLeay License
1. Redistributions of source code must retain the above copyright
Copyright (C) 1995-1998 Eric Young (eay@cryptsoft.com) All
rights reserved.
notice, this list of conditions and the following disclaimer.
2. Redistributions in binary form must reproduce the above
This package is an SSL implementation written by Eric Young
(eay@cryptsoft.com). The implementation was written so as to
conform with Netscapes SSL.
copyright notice, this list of conditions and the following
disclaimer in the documentation and/or other materials
provided with the distribution.
This library is free for commercial and non-commercial use as long
as the following conditions are aheared to. The following conditions
apply to all code found in this distribution, be it the RC4, RSA, lhash,
DES, etc., code; not just the SSL code. The SSL documentation
included with this distribution is covered by the same copyright
terms except that the holder is Tim Hudson (tjh@cryptsoft.com).
Copyright remains Eric Young's, and as such any Copyright notices
in the code are not to be removed. If this package is used in a
product, Eric Young should be given attribution as the author of the
parts of the library used. This can be in the form of a textual
message at program startup or in documentation (online or textual)
provided with the package.
3. All advertising materials mentioning features or use of this
software must display the following acknowledgment: "This
product includes software developed by the OpenSSL Project
for use in the OpenSSL Toolkit. (http://www.openssl.org/)"
4. The names "OpenSSL Toolkit" and "OpenSSL Project" must
not be used to endorse or promote products derived from this
software without
5. prior written permission. For written permission, please contact
openssl-core@openssl.org.
6. Products derived from this software may not be called
"OpenSSL" nor may "OpenSSL" appear in their names without
prior written permission of the OpenSSL Project.
Redistribution and use in source and binary forms, with or without
modification, are permitted provided that the following conditions are
met:
7. Redistributions of any form whatsoever must retain the
following acknowledgment: "This product includes software
developed by the OpenSSL Project for use in the OpenSSL
Toolkit (http://www.openssl.org/)"
1. Redistributions of source code must retain the copyright notice,
this list of conditions and the following disclaimer.
2. Redistributions in binary form must reproduce the above
THIS SOFTWARE IS PROVIDED BY THE OpenSSL PROJECT
``AS IS'' AND ANY EXPRESSED OR IMPLIED WARRANTIES,
INCLUDING, BUT NOT LIMITED TO, THE IMPLIED WARRANTIES
OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR
PURPOSE ARE DISCLAIMED. IN NO EVENT SHALL THE
OpenSSL PROJECT OR ITS CONTRIBUTORS BE LIABLE FOR
ANY DIRECT, INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY,
OR CONSEQUENTIAL DAMAGES (INCLUDING, BUT NOT
LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR
SERVICES; LOSS OF USE, DATA, OR PROFITS; OR BUSINESS
INTERRUPTION) HOWEVER CAUSED AND ON ANY THEORY
OF LIABILITY, WHETHER IN CONTRACT, STRICT LIABILITY, OR
TORT (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN
copyright notice, this list of conditions and the following
disclaimer in the documentation and/or other materials
provided with the distribution.
3. All advertising materials mentioning features or use of this
software must display the following acknowledgement: "This
product includes cryptographic software written by Eric Young
(eay@cryptsoft.com)" The word 'cryptographic' can be left out if
the rouines from the library being used are not cryptographic
related.
4. If you include any Windows specific code (or a derivative
thereof) from the apps directory (application code) you must
include an acknowledgement: "This product includes software
written by Tim Hudson (tjh@cryptsoft.com)"
iv
Environmental Compliance
THIS SOFTWARE IS PROVIDED BY ERIC YOUNG ``AS IS'' AND
ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT
NOT LIMITED TO, THE IMPLIED WARRANTIES OF
MERCHANTABILITY AND FITNESS FOR A PARTICULAR
PURPOSE ARE DISCLAIMED. IN NO EVENT SHALL THE
AUTHOR OR CONTRIBUTORS BE LIABLE FOR ANY DIRECT,
INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR
CONSEQUENTIAL DAMAGES (INCLUDING, BUT NOT LIMITED
TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES;
LOSS OF USE, DATA, OR PROFITS; OR BUSINESS
INTERRUPTION) HOWEVER CAUSED AND ON ANY THEORY
OF LIABILITY, WHETHER IN CONTRACT, STRICT LIABILITY, OR
TORT (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN
ANY WAY OUT OF THE USE OF THIS SOFTWARE, EVEN IF
ADVISED OF THE POSSIBILITY OF SUCH DAMAGE.
USA
Energy Star
As an ENERGY STAR® partner, Xerox Corporation
has determined that (the basic configuration of) this
product meets the ENERGY STAR guidelines for
energy efficiency.
The ENERGY STAR and ENERGY STAR MARK
are registered United States trademarks.
The ENERGY STAR Office Equipment Program is
a team effort between U.S., European Union and
Japanese governments and the office equipment
industry to promote energy-efficient copiers,
printers, fax, multifunction machine, personal
computers, and monitors. Reducing product energy
consumption helps combat smog, acid rain and
long-term changes to the climate by decreasing the
emissions that result from generating electricity.
The licence and distribution terms for any publically available
version or derivative of this code cannot be changed. i.e. this code
cannot simply be copied and put under another distribution licence
[including the GNU Public Licence.]
Xerox ENERGY STAR equipment is preset at the
factory. Your machine will be delivered with the
timer for switching to Power Save Mode from the
last copy/print out, set at 30 minutes. A more
detailed description of this feature can be found in
the Machine Setup Section of this guide.
v
Product Recycling and Disposal
If you are managing the disposal of your Xerox product, please note
that the product may contain lead, Perchlorate and other materials
whose disposal may be regulated due to environmental
considerations. The presence of these materials is fully consistent
with global regulations applicable at the time that the product was
placed on the market. For recycling and disposal information,
contact your local authorities. In the United States, you may also
refer to the Electronic Industries Alliance web site: www.eiae.org.
European Union
Domestic/Household Environment
Application of this symbol on your equipment is
confirmation that you should not dispose of the
equipment in the normal household waste stream. In
accordance with European legislation, end of life
electrical and electronic equipment subject to disposal
must be segregated from household waste. Private
households within EU member states may return
used electrical and electronic equipment to
designated collection facilities free of charge. Please
contact your local disposal authority for information. In
some member states, when you purchase new
equipment, your local retailer may be required to take
back your old equipment free of charge. Please ask
you retailer for information.
Perchlorate Material - This product may contain one or more
Perchlorate-containing devices, such as batteries. Special handling
may apply, please see www.dtsc.ca.gov/hazardouswaste/
perchlorate/.
Others Countries
Please contact your local waste authorities and request disposal
guidance.
EH&S Contact Information
For more information on Environment, Health and Safety in relation
to this Xerox product and supplies, please contact the following
customer help lines: USA: 1-800 828-6571 Canada: 1-800 8286571 Europe: +44 1707 353 434.
Prior to disposal, please contact your local dealer or
Xerox representative for end of life takeback
information.
•
Product Safety information for US
www.xerox.com/about-xerox/environment/enus.html
Professional/Business Environment
•
Application of this symbol on your equipment is
confirmation that you must dispose of this equipment
in compliance with agreed national procedures.
Product Safety information for EU
www.xerox.com/about-xerox/environment/eneu.html
In accordance with European legislation, end of life
electrical and electronic equipment subject to disposal
must be managed within agreed procedures.
North America
Xerox operates an equipment takeback and reuse/recycle program.
Contact your Xerox sales representative (1-800-ASK-XEROX) to
determine whether this Xerox product is part of the program. For
more information about Xerox environmental programs, visit
www.xerox.com/environment or for recycling and disposal
information, contact your local authorities. In the United States, you
may also refer to the Electronic Industries Alliance web site:
www.eiae.org.
Xerox operates a worldwide equipment take back and reuse/recycle
program. Contact your Xerox sales representative (1-800-ASKXEROX) to determine whether this Xerox product is part of the
program. For more information about Xerox environmental
programs, visit www.xerox.com/environment.
vi
1 Introduction
Save time and money
Congratulations on the purchase of your printer!
This chapter includes:
•
Special features
•
Printer overview
•
Finding more information
1
2
3
4
• This printer automatically conserves electricity
by substantially reducing power consumption
when not in use.
Expand the printer capacity
Your new printer is equipped with several special features that improve
the print quality. You can:
• The Phaser 3435 series have 64 MB of memory
which can be expanded to 320 MB. See
page 10.1.
Print with excellent quality and high speed
• A Network interface enables network printing.
• You can print up to 1200 x 1200 dpi effective
output. See the Software section.
• A PostScript 3 Emulation* (PS) enables PS
printing.
ppma
• Your printer prints A4-sized paper at up to 33
and letter-sized paper at up to 35 ppm. For duplex
printing, your printer prints A4-sized paper at up to
17 ipmb and letter-sized paper at up to 17.5 ipm.
* Zoran IPS Emulation compatible with PostScript 3
Handle paper flexibly
• © Copyright 1995-2005, Zoran Corporation.
All rights reserved. Zoran, the Zoran logo, IPS/PS3
and OneImage are trademarks of Zoran
Corporation.
• multi-purpose tray supports letterheads, envelopes,
labels, transparencies, custom-sized materials,
postcards, and heavy paper. multi-purpose tray
holds up to 50 sheets of plain paper.
• 250-sheet tray 1 and 250-sheet optional tray 2
support plain paper in various sizes.
* 136 PS3 fonts
• Contains UFST and MicroType from Monotype Imaging Inc.
• Multiple output tray; select either the output tray
(face-down) or the rear cover (face-up) for the
most convenient access.
Print in various environments
• You can print in Windows 2000/XP/Vista/2003.
• Your printer is compatible with Macintosh.
• Straight-through paper path capability from multipurpose tray to the rear cover.
• Your printer comes with both Parallel and USB interfaces.
• You can also use a network interface. The Phaser 3435/DN comes
with a built-in network interface, 10/100 Base TX.
Create professional documents
9
• You can print multiple pages on a single sheet of
paper to save paper (2-Up printing). See the
Software section.
• You can use preprinted forms and letterhead with
plain paper. See the Software section.
Special features
8
• You can print on both sides of the paper to save
paper (Double-sided printing).
• Print Watermarks. You can customize your
documents with words, such as “Confidential”. See
the Software section.
• Print Booklets. This feature enables you to easily
print a document to create a book. Once printed, all
you have to do is fold and staple the pages. See the
Software section.
• Print Posters. The text and pictures of each page
of your document are magnified and printed across
the sheet of paper and can then be taped together
to form a poster. See the Software section.
a. pages per minute
b. images per minute
1.1
<Introduction>
Printer features
Printer overview
The table below lists a general overview of features supported by your
printer.
Front view
(I: Installed, O: Option, NA: Not Available)
Features
Phaser 3435/DN
IEEE 1284 Parallel
I
USB 2.0
I
Network Interface
I
(Ethernet 10/100 Base TX)
PostScript* Emulation
Duplex printing
a
I
I
a. Printing on both sides of paper.
* The figure above shows an Phaser 3435/DN
with all available options.
1.2
1
output tray
7
multi-purpose tray
2
control panel
8
front cover
3
handle
9
output support
4
paper level indicator
10
multi-purpose tray
paper width guides
5
optional tray 2
11
multi-purpose tray
extension
6
tray 1
<Introduction>
Rear view
Control panel overview
/
* The figure above shows an Phaser 3435/DN
with all available options.
1
Start/Stop: Cancels an operation at any time; resumes
printing.
2
Back: Sends you back to the upper menu level.
3
Status: Shows the status of your printer. See page 1.4.
4
Menu: Enters Menu mode and scrolls through the available
menus.
5
LCD: Displays the printer status, error messages and menus
in progress.
1
control board cover
6
duplex unit
2
network port
7
power receptacle
6
scroll: Scrolls through the options available in the selected
menu, and increases or decreases value.
3
USB port
8
power switch
7
OK: Confirms the selection on the display.
4
parallel port
9
rear cover
5
optional tray 2 cable
connector
1.3
<Introduction>
Understanding the Status LED
Status
Off
Finding more information
You can find information for setting up and using your from the following
resources, either printed or onscreen.
Description
• The printer is powerd off.
On
• The printer is on.
• The printer can receive data from the
computer.
Blinking
• When the backlight blinks slowly, the printer
is receiving data from the computer.
• When the backlight blinks quickly, the printer
is printing data.
On
• A paper jam has occurred. To solve the
problem, see page 9.1.
• The front cover is open. Close the front
cover.
• There is no paper in the tray. Load paper in
the tray.
• The print cartridge installed is not a genuine
cartridge, and you selected Stop at the
NonGenuine Toner prompt. See page 9.6.
• The lifespan of the print cartridge is reached,
and you selected Stop at the Toner
Exhausted prompt. See page 9.6.
• The printer has stopped printing due to a
major error.
Blinking
• A minor error is occurring and the printer is
waiting for the error to be cleared. When the
problem is cleared, the printer resumes
printing.
• The print cartridge is totally exhausted.
Remove the old print cartridge and install a
new one. See page 8.3.
• The print cartridge installed is not a genuine
cartridge, and you selected Continue at the
NonGenuine Toner prompt. See page 9.6.
• The lifespan of the print cartridge is reached,
and you selected Continue at the Toner
Exhausted prompt. See page 9.6.
• The print cartridge is low. Order a new print
cartridge. You can temporarily improve print
quality by redistributing the toner. See
page 8.3.
Green
Red
Quick Install
Guide
Provides information on setting up your printer
and, therefore, be sure to follow the
instructions in the guide to get the printer
ready.
Quick Use Guide
Provides information on using your printer or
cleaning jam and, therefore, be sure to follow
the instructions in the guide to use the printer.
Workcentre 3428
Online User’s
Guide
Provides you with step-by-step instructions for
using your printer’s full features, and contains
information for maintaining your printer,
troubleshooting, and installing accessories.
This user’s guide also contains the Software
Section providing you with information on how
to print documents with your printer on various
operating systems, and how to use the
supplied software utilities.
Note
You can access the user’s guides in
other languages from the Manual
folder on the printer driver CD.
1.4
Printer Driver
Help
Provides you with help information on printer
driver properties and instructions for setting up
the properties for printing. To access a printer
driver help screen, click Help from the printer
properties dialog box.
Xerox website
If you have Internet access, you can get help,
support, printer drivers, manuals, and order
information from the Xerox website,
www.xerox.com/office/support.
<Introduction>
Selecting a location
Select a level, stable place with adequate space for air circulation. Allow
extra space for opening covers and trays.
The area should be well-ventilated and away from direct sunlight or
sources of heat, cold, and humidity. Do not set the printer close to the
edge of your desk or table.
Clearance space
Front: 500 mm (enough space
so that trays can be opened or
removed)
Back: 350 mm (enough space
to allow opening of the rear
cover or the duplex unit)
Right: 100 mm (enough space
for ventilation)
Left: 100 mm (enough space
to allow opening of the control
board cover)
1.5
<Introduction>
2 System setup
Menu overview
The control panel menus are used to configure the printer. The control
panel provides access to the following menus:
This chapter provides step by step information on setting up your printer.
This chapter includes:
•
Using control panel menus
•
Menu overview
•
Printing a demo page
•
Changing the display language
Using control panel menus
A number of menus are available to make it easy for you to change the
printer settings. The diagram on the next column shows the menus and
all of the menu items available in each menu. The items in each menu
and the options you can select are described in more detail in the tables
beginning on page 2.2.
Accessing control panel menus
Information
Layout
(See page 2.2.)
Menu Map
Configuraton
Demo Page
PCL Font List
PS3 Font Lista
EPSON Font
(See page 2.2.)
Orientation
Simplex Margin
Duplex
Duplex Margin
Graphic
Paper
(See page 2.4.)
Resolution
Darkness
(See page 2.3.)
Copies
Paper Size
Paper Type
Paper Source
Tray Chaining
System Setup
Emulation
(See page 2.4.)
Language
Power Save
Auto Continue
Altitude Adj.
Auto CR
Job Timeout
Maintenance
Clear Setting
(See page 2.5.)
Emulation Type
Setup
You can control your printer from the printer’s control panel. You can
also set the control panel menus while the printer is in use.
1
Press Menu until the menu you want appears on the bottom line of
the display and press OK.
2
Press the Up/down arrow buttons until the desired menu item
appears and press OK.
3
If the menu item has sub menus, repeat step 2.
4
Press the Up/down arrow buttons to access the desired setting
option or the required value.
5
Press OK to save your selection.
An asterisk (*) appears next to the selection on the display,
indicating that it is now the default.
6
Press Start/Stop to return to Standby mode.
Networka
After 30 seconds of inactivity (no key being pressed), the printer
automatically returns to Standby mode.
(See page 2.6.)
TCP/IP
EtherTalk
Ethernet Speed
Clear Setting
Network Info.
802.1x
CentreWare IS
Note
Print settings made from the printer driver on a connected
computer override the settings on the control panel.
Note
Some menus may not appear in the display depending on
options or models. If so, it is not applicable to your machine.
a. Available when the installed memory is larger than 128 MB.
2.1
<System setup>
Information menu
Layout menu
This menu contains printer information pages that give details about the
printer and its configuration.
Use the Layout menu to define all settings relating to output.
Item
Item
Explanation
Menu Map
The menu map shows the layout and current
settings of the control panel menu items.
Configuraton
The configuration page shows the printer’s
current configuration. See page 8.1.
Demo Page
The demo page allows you to check if your
printer properly performs printing. See
page 2.7.
PCL Font List
PS3 Font List
The font sample list shows all of the fonts
currently available in the selected language.
EPSON Font
The font sample list shows all of the fonts
currently available in the selected language.
Explanation
Orientation
Values: Portrait, Landscape
Choose the default orientation of the print image
on the page.
Landscape
Portrait
Simplex
Margin
Duplex
Set the margin of print materials for one-sided
printing. You can increase or decrease the value in
0.1 mm increments. The margins may differ
according to the paper size and printing
orientation.
• Top Margin: Set the top margin, from 0.0 to
250 mm.
• Left Margin: Set the left margin, from 0.0 to
164 mm.
Values: Off, Long Edge, Short Edge
To print on both sides of paper, choose the binding
edge as follows.
• Long Edge: Flip on the long edge. Prints pages
to read like a book.
• Short Edge: Flip on the short edge. Prints
pages to read by flipping over like a note pad.
2
3
2
5
3
5
Long Edge in the
Portrait orientation
Long Edge in the
Landscape orientation
2
3
2
5
3
5
Short Edge in the
Portrait orientation
Short Edge in the
Landscape orientation
Select Off to print on one side of the paper.
2.2
<System setup>
Item
Duplex
Margin
Paper menu
Explanation
Use the Paper menu to define all settings relating to print material input
and output, as well as the specific print material you are using with your
printer.
In this menu, you can set the margins for doublesided printing. You can increase or decrease the
value in 0.1 mm increments.
• Top Margin: Set the top margin, from 0.0 to 9.9
mm. The default is 5.0 mm.
• Left Margin: Set the left margin, from 0.0 to 9.9
mm. The default is 5.0 mm.
• Short Binding: Set the bottom margin of the
back of the page for short binding, from 0.0 to 22
mm. The default is 0 mm.
• Long Binding: Set the right margin of the back
of the page for long binding, from 0.0 to 22 mm.
The default is 0 mm.
Item
Copies
Explanation
Values: 1 ~ 999
Set the default number of copies by selecting any
number from 1 to 999. The default is 1.
Paper Size
Values: A4, A5, A6, JIS B5, ISO B5, Letter,
Legal, Executive, No.10 Env., Monarch Env., DL
Env., C5 Env., C6 Env., US Folio, Oficio,
Custom Paper
Select the paper size currently loaded in tray.
• Custom Paper: You can configure the size for
your own custom paper. Set the width from 98
mm to 216 mm, and the height from 148 mm to
356 mm.
Paper Type
Values: Plain Paper, Bond, Transparency,
Envelope, Labels, Card Stock, Preprinted,
Color, Cotton Paper, Recycled, Achive, Thick,
Thin
Select the paper type currently loaded in tray.
Paper
Source
Values: , Tray 1, Tray 2, MP Tray,
Manual Tray, Auto
Using this item, you can set which tray you want to
use.
• Auto: The printer can automatically determine
the source.
• Manual Tray: The printer uses MP Tray.
• Tray 2: Available only when optional tray is
installed.
Tray
Chaining
Values: Off, On
When you select any other value except Auto from
Paper Source and the selected tray is empty, the
printer automatically prints from other trays.
If this menu item is set to Off, the Status LED lights
red and the printer doesn’t work until you insert
paper into the specified tray.
2.3
<System setup>
Graphic menu
System Setup menu
Use the Graphic menu to change settings affecting the quality of the
printed characters and images.
Use the System Setup menu to configure a variety of printer features.
Item
Item
Resolution
Explanation
Language
Values: 600dpi-Normal, 1200dpi-Best
Values: English, FRANCAIS, Espanol,
Portugues B., Deutsch, Italiano...
This setting determines the language of the text
that appears on the control panel display and
information printing.
Specify the number of dots printed per inch (dpi).
The higher the setting, the sharper printed
characters and graphics.
Power Save
• If your print jobs are mostly text, select 600dpiNormal for the highest quality printing.
• Select 1200dpi-Best when your job contains
bitmapped images, such as scanned photos or
some graphics, that will benefit from enhanced
line screening.
Darkness
Explanation
Values: [ 5 ] Min, [ 10 ] Min, [ 15 ] Min, [ 20 ]
Min, [ 30 ] Min, [ 60 ] Min, [ 120 ] Min
When the printer does not receive data for an
extended period of time, power consumption is
automatically lowered. You can set how long
the printer waits before going to power save
mode.
Values: Plain, Light, Dark
Auto Continue
You can lighten or darken the print on the page by
changing the toner density setting. The Plain
setting usually produces the best result. Use the
Light toner density setting to save toner.
Values: Off, On
This item determines whether or not the printer
continues printing when it detects the paper is
mismatched with your paper setting.
• Off: If a paper mismatch occurs, the message
will remain on the display and the printer will
remain off-line until you insert the correct
paper.
• On: If a paper mismatch occurs, an error
message will display. The printer will go
offline for 30 seconds, then automatically
clear the message and continue printing.
Altitude Adj.
Values: Plain, High1, High2, High3
You can optimize print quality according to your
altitude.
Auto CR
Values: LF, LF+CR
This item allows you to append the required
carriage return to each line feed.
Refer to the following samples:
2.4
<System setup>
AA
BB
CC
AA
BB
CC
LF
LF+CR
Item
PCL
Explanation
Job Timeout
This menu sets the PCL emulation configuration. You can set the font
type, symbol type, lines per page, and point size.
Values: 0 ~ 1800 sec
You can set the length of time the printer waits
before printing the last page of a print job that
does not end with a command to print the page.
The default is 15 sec.
Maintenance
Item
Typeface
You can select the standard font to be used in PCL
emulation.
This item allows you to maintain your printer.
• PCL 1~PCL 7’s interval between letters is fixed, and
PCL 8~PCL 45’s interval is proportional to the font
type and point size. You can adjust the font size of
PCL 1~PCL 7 using the Pitch item, and
PCL 8~PCL 45 can do using Point Size item.
• PCL 46~PCL 54’s interval and point size are fixed.
Symbol
This menu item allows you to restore the
printer’s factory default settings.
Emulation menu
Explanation
Courier
Values: Auto, PCL, EPSON, PostScript, IBM
Values: Regular, Dark
This item lets you select the version of Courier font to
use.
The printer language defines how the computer
communicates with the printer.
If you select Auto, your printer can change the
printer language automatically.
Setup
Values: 4.00 ~ 999.75 (0.25 unit)
When you select one between PCL 8 and PCL 45 from
the Typeface menu, you can determine the font size
by setting the height of the characters in the font. The
default is 12.00.
Use the Emulation menu to configure printer language emulation.
Emulation
Type
Values: ROMAN8 ~ PCYRIL
This item selects the symbol to be used in PCL
emulation. The symbol is the group of numbers,
marks, and special signs being used when printing
letters. The default is PC8.
Point Size
Item
Values: PCL 1 ~ PCL 54
When a print time-out occurs, the printer prints
the page in the print buffer.
• Clean Drum: Cleans the OPC drum of the
cartridge and produces a cleaning sheet with
toner debris on it.
• Clean Fuser: Cleans the fuser unit inside of
the printer and produces a cleaning sheet
with toner debris on it.
• Supplies Life: This item allows you to check
how many pages have printed and how much
toner is left in the cartridge.
Clear Setting
Explanation
Pitch
Values: 0.44 ~ 99.99 (0.01 unit)
When you select a font between PCL 1 and PCL 7
from the Typeface menu, you can determine the font
size by setting the number of characters that will print
in one horizontal inch of type. The default value, 10 is
the best size.
Values: PCL, PostScript, EPSON
See the tables on page 2.5 to configure the printer
language.
Lines
Values: 5 ~ 128 (1 unit)
This item allows you to set vertical spacing from 5 to
128 lines for the default paper size. The lines may
differ according to the paper size and printing
orientation.
2.5
<System setup>
PostScript
Network menu
This menu provides you with the Print PS Error menu item.
This menu lets you configure the network interface installed in your
printer. You can reset the network interface and print a configuration
page.
Item
Print PS
Error
Explanation
Item
Values: On, Off
TCP/IP
You can select whether or not your printer prints an
error list when a PS error occurs.
• DHCP: The DHCP server assigns the IP address
to you automatically.
• BOOTP: The BOOTP server assigns the IP
address to you automatically.
• Static: You can enter IP address, subnet mask,
and gateway manually.
EPSON
This menu sets the EPSON emulation configuration.
Font
EtherTalk
Explanation
• Off: You can disable the EtherTalk protocol.
• On: You can enable the EtherTalk protocol.
Ethernet
Speed
Values: USA, FRANCE, GERMANY, UK,
DENMARK1, SWEDEN, ITALY, SPAIN1, JAPAN,
NORWAY, DENMARK2, SPAIN2, LATIN
Values: 10, 12, 17.14, 20
Network
Info.
This item prints a page showing the network
parameters you set.
Values: Off, On
This item is for connecting with an authentication
server. If you need to connect this product to an
authentication server, set this item On.
Values: 6, 8
CentreWare
IS
You can set the number of lines printed in one vertical
inch.
Auto
Wrap
This item performs a simple reset and restores the
factory default settings for the network
configuration. This setting will only take effect after
you have reset the printer.
802.1x
You can determine the font size by setting the number
of characters that will print in one horizontal inch of
type.
LPI
Clear
Setting
Values: ITALIC, PC437US, PC850
This item selects the character set.
Pitch
Values: Auto, 10M Half, 10M Full, 100M Half,
100M Full
This item allows you to select the ethernet speed.
This item allows you to select a character set of the
desired language.
Character
Tab.
Values: Off, On
This item lets you select whether or not you use the
EtherTalk protocol.
Values: SANSERIF, ROMAN
You can select the standard font that will be used in
EPSON emulation.
Character
Set
Values: DHCP, BOOTP, Static
This item allows you to manually set the TCP/IP
addresses or receive the addresses from the
network.
• Select On to print PS 3 emulation errors. If an error
occurs, the job stops processing, the error message
prints, and the printer flushes the job.
• If this menu is set to Off, the job is flushed without an
indication of the error.
Item
Explanation
Values: Off, On
This item lets you select whether or not you use the
embeded web server called CentreWare IS. If you
turn this item Off, you cannot connect to the
printer’s embeded web server.
Values: Off, On
This item determines whether or not the printer
automatically performs line feed when the data
overflows the printable area of the print material.
2.6
<System setup>
Printing a demo page
Print a demo page to make sure that the printer is operating correctly.
1
Press Menu and then OK when Information appears.
2
Press the Up/down arrow buttons until Demo Page appears and
press OK.
A demo page prints out.
Changing the display language
To change the language that is displayed on the control panel, follow
these steps:
1
Press Menu until System Setup appears on the bottom line of the
display and press OK.
2
Press OK when Language appears.
3
Press the Up/down arrow buttons to select the language you want
and press OK.
4
Press Start/Stop to return to Standby mode.
Using toner save mode
Toner save mode allows the printer to use less toner on each page.
Activating this mode extends the life of your print cartridge and reduces
your cost per page beyond what one would experience in the normal
mode, but it reduces print quality.
There are two ways to enable this mode:
Using the control panel button
Press Toner Save on the control panel. The printer must be in Standby
mode; the Status LED lights green and Ready is shown on the display.
• If the button backlight is on, the mode is enabled and the printer uses
less toner to print a page.
• If the button backlight is off, the mode is disabled and the printer prints
in normal mode.
From the software application
You can set toner save mode from the printer properties window on your
printer driver. See the Software Section.
2.7
<System setup>
3 Software overview
Supplied software
You must install the printer software using the supplied CD after you
have set up your printer and connected it to your computer.
This chapter gives you an overview of the software that comes with your
printer. Further details about installing and using the software are
explained in the Software Section.
CD provides you with the following software:
This chapter includes:
•
Supplied software
•
Printer driver features
•
System requirements
CD
Printer
software CD
Contents
Windows
• Printer driver: Use this driver to
take full advantage of your printer’s
features.
• Status Monitor: Appears when
printing errors occur.
• Printer Settings Utility: You can
configure print settings.
• PostScript Printer Description
(PPD) file: Use the PostScript
driver to print documents with
complex fonts and graphics in the
PostScript language.
• SetIP: Use this program to set your
printer’s TCP/IP addresses.
• User Guide in PDF.
3.1
<Software overview>
Linux
• Printer driver: Use this driver to
run your machine from a Linux
computer and print documents.
Mac OS
• PostScript Printer Description
(PPD) file: Use this file to run your
printer from a Macintosh computer
and print documents.
Printer driver features
System requirements
Your printer drivers support the following standard features:
• Paper source selection
Before you begin, ensure that your system meets the following
requirements:
• Paper size, orientation and media type
Windows
• Number of copies
Item
In addition, you can use various special printing features. The following
table shows a general overview of features supported by your printer
drivers:
Feature
Windows
Mac OS
PCL 6
PostScript
PostScript
Print quality option
O
O
O
Poster printing
O
X
X
Multiple pages per sheet
(N-up)
O
O
O
Fit to page printing
O
O
O
Scale printing
O
O
O
Different source for first
page
O
X
O
Watermark
O
X
X
Overlay
O
X
X
Requirements
Recommended
Operating
system
Windows 2000/XP/Vista/2003
CPU
Windows 2000
Pentium II
400 MHz or
higher
Pentium III
933 MHz
Windows XP/
2003
Pentium III
933 MHz or
higher
Pentium IV
1 GHz
Windows Vista
Pentium IV
3 GHz or higher
Pentium IV
3 GHz
Windows 2000
64 MB or more
128 MB
Windows XP/
2003
128 MB or more
256 MB
Windows Vista
512 MB or more
1024 MB
Windows 2000
300 MB or more
1 GB
Windows XP/
2003
1 GB or more
5 GB
Windows Vista
15 GB or more
15 GB
RAM
Free disk
space
Internet
Explorer
5.0 or higher
Note
Users who have administrator rights can install the software.
Mac OS
Item
3.2
Requirements
Operating system
Mac OS 10.3 ~ 10.5
CPU
Intel processor PowerPC G4/G5
RAM
Intel-based Mac
512 MB
Power-PC based Mac
128 MB
Free HDD space
1 GB
Connection
USB interface, Network interface
<Software overview>
4 Network setup
Supported operating systems
The following table shows the network environments supported by the
printer:
This chapter gives you step-by-step instructions for setting up your
printer for network connections.
This chapter includes:
Item
•
Introduction
•
Supported operating systems
•
Configuring TCP/IP
•
Configuring EtherTalk
•
Setting Ethernet speed
•
Restoring the network configuration
•
Printing a network configuration page
•
Configuring 802.1x
•
Configuring CentreWare IS
Requirements
Network interface
• 10/100 Base-TX
Network operating
system
• Windows 2000/XP/Vista/2003
• Mac OS 10.3 ~ 10.5
• Various Linux OS
Network protocols
•
•
•
•
Dynamic addressing
server
• DHCP, BOOTP
TCP/IP on Windows
EtherTalk
802.1x
CentreWare IS
• TCP/IP: Transmission Control Protocol / Internet Protocol
• DHCP: Dynamic Host Configuration Protocol
• BOOTP: Bootstrap Protocol
Introduction
Once you have connected your printer to a network with an RJ-45
Ethernet cable, you can share the printer with other network users.
You need to set up the network protocols on the printer to use it as your
network printer.
Via network administration programs
You can configure your printer’s print server settings and manage the
printer via the following programs that came with your printer:
• CentreWare IS: A web server embedded in your network printer,
which allows you to remotely configure the printer settings and
network parameters necessary for the printer to be connected to
various network environments.
• SetIP: A utility program allowing you to select your network printer
and manually configure the printer's TCP/IP addresses.
Via the control panel
You can set up the following basic network parameters through the
printer’s control panel:
• Configure TCP/IP
• Configure EtherTalk, 802.1x, and CentreWare IS
4.1
<Network setup>
Configuring TCP/IP
Configuring EtherTalk
Your printer can be set up with a variety of TCP/IP network information,
such as an IP address, a subnet mask, a gateway, and DNS addresses.
There are several ways in which your printer can be assigned a TCP/IP
address, depending on your network.
EtherTalk is AppleTalk used in an Ethernet network. This protocol is
widely used in Macintosh network environments. To use EtherTalk, take
the following steps:
1
Press Menu until Network appears on the bottom line of the
display and press OK.
2
Press the Up/down arrow buttons until EtherTalk appears and
press OK.
Note
3
Press the Up/down arrow buttons until On appears and press OK.
Before configuring TCP/IP, you need to set the network
protocol to TCP/IP.
4
Press Start/Stop to return to Standby mode.
• Static addressing: A TCP/IP address is assigned manually by the
system administrator.
• Dynamic addressing via BOOTP/DHCP (default): A TCP/IP address
is assigned automatically by the server.
Static addressing
Setting Ethernet speed
To enter a TCP/IP address from your printer’s control panel, take the
following steps:
You can select the communication speed for Ethernet connections.
1
Press Menu until Network appears on the bottom line of the
display and press OK.
1
Press Menu until Network appears on the bottom line of the
display and press OK.
2
Press OK when TCP/IP appears.
2
Press the Up/down arrow buttons until Ethernet Speed appears
and press OK.
3
Press the Up/down arrow buttons until Static appears and press
OK.
3
Press the Up/down arrow buttons until the speed you want
appears and press OK.
4
Press OK when IP Address appears.
4
Press Start/Stop to return to Standby mode.
5
Set the first byte between 0 and 255 using the Up/down arrow
buttons and press OK to move to the next byte.
Restoring the network configuration
Repeat this to complete the address from the 1st byte to the 4th
byte.
6
When you have finished, press OK.
7
Repeat step 5 and 6 to configure the other TCP/IP parameters:
subnet mask and gateway address.
8
Press Start/Stop to return to Standby mode.
You can return the network configuration to its default settings.
Dynamic addressing (BOOTP/DHCP)
To have a TCP/IP address assigned automatically by the server, take the
following step:
1
Press Menu until Network appears on the bottom line of the
display.
2
Press OK when TCP/IP appears.
3
Press the Up/down arrow buttons until DHCP or BOOTP appears
and press OK.
4
Press Start/Stop to return to Standby mode.
4.2
1
Press Menu until Network appears on the bottom line of the
display and press OK.
2
Press the Up/down arrow buttons until Clear Setting appears and
press OK.
3
Press OK when Yes appears to restore the network configuration.
4
Power the printer off and back on.
<Network setup>
Printing a network configuration page
Configuring CentreWare IS
The network configuration page shows how the network interface card
on your printer is configured.
Your printer can use CentreWare IS (Internet Services). To enable
CentreWare IS, take the following steps:
1
Press Menu until Network appears on the bottom line of the
display and press OK.
1
Press Menu until Network appears on the bottom line of the
display and press OK.
2
Press the Up/down arrow buttons until Network Info. appears and
press OK.
2
Press the Up/down arrow buttons until CentreWare IS appears
and press OK.
3
Press OK when Yes appears.
3
Press the Up/down arrow buttons until On appears and press OK.
The network configuration page prints out.
Configuring 802.1x
Your printer has 802.1x protocol on its network. 802.1x is a security
standard for port based network access control. It secures your network
against unauthorized access by requiring authentication before network
access and data transmission are allowed. There are 3 mutually
exclusive options for 802.1x authentication.
To use 802.1x, take the following steps:
1
Press Menu until Network appears on the bottom line of the
display and press OK.
2
Press the Up/down arrow buttons until 802.1x appears and press
OK.
3
Press the Up/down arrow buttons until On appears and press OK.
4
Press the Up/down arrow buttons until the desired authentication
method appears.
• EAP-MD5: EAP-MD5 (Extensible Authentication Protocol
Message Digest algorithm 5) is a message hashing scheme
between client and server to allow the transfer of user data in a
secure fashion.
• EAP-MSCHAPv2: EAP-MSCHAP (Extensible Authentication
Protocol Microsoft version of the Challenge-Handshake
Authentication Protocol). MSCHAP v2 is a one-way encrypted
password, mutual authentication process. MS-CHAPv2 uses
different hashing/encryption algorithms to encode the UserID and
passwords.
• PEAP: PEAP (Protected EAP).
5
Enter user name and passcode using Up/down arrow button.
6
Press OK to save the selection.
7
Press Start/Stop to return to Standby mode.
4.3
<Network setup>
5 Loading print media
Selecting print media
This chapter includes:
You can print on a variety of print media, such as plain paper, envelopes,
labels, and transparencies. Always use print media that meet the
guidelines for use with your printer. Print media that does not meet the
guidelines outlined in this user’s guide may cause the following
problems:
•
Selecting print media
• Poor print quality
•
Loading paper
• Increased paper jams
•
Selecting an output location
• Premature wear on the printer.
This chapter will help you understand types of paper you can use with
your printer and how to properly load paper in the different paper trays
for the best print quality.
Properties, such as weight, composition, grain, and moisture content,
are important factors that affect the printer’s performance and the output
quality. When you choose print materials, consider the following:
• Desired outcome: The print media you choose should be appropriate
for your project.
• Size: You can use any size media that fits easily within the paper
adjusters of the paper tray.
• Weight: Your printer supports print media weights as follows:
- 16 to 24 lb bond (60 to 90 g/m2) for the tray 1 and optional tray 2
- 16 to 43 lb bond (60 to 163 g/m2) for the multi-purpose tray
- 20 to 24 lb (75 to 90 g/m2) for the duplex printing
• Brightness: Some print media are whiter than others and produce
sharper, more vibrant images.
• Surface smoothness: The smoothness of the print media affects how
crisp the printing looks on the paper.
Notes
• Some print media may meet all of the guidelines in this
section and still not produce satisfactory results. This may be
the result of improper handling, unacceptable temperature
and humidity levels, or other variables over which Xerox has
no control.
• Before purchasing large quantities of print media, ensure that
it meets the requirements specified in this user’s guide.
Caution
Using print media that does not meet these specifications may
cause problems, requiring repairs. Such repairs are not
covered by Xerox’s warranty or service agreements.
5.1
<Loading print media>
Supported sizes of paper
Type
Size
Weighta
Dimensions
Capacityb
• 60 to 90 g/m2 (16 to 24 lb
bond ) for the tray
• 60 to 163 g/m2 (16 to 43 lb
bond ) for the multipurpose tray
• 250 sheets of 80 g/m2
(20 lb bond) paper for the
tray
• 50 sheets for the multipurpose tray
75 to 90 g/m2 (20 to 24 lb)
5 sheets of 75 g/m2 (20 lb) in
the multi-purpose tray
Refer to the Plain paper section
138 to 146 g/m2
5 sheets of 75 g/m2 (20 lb) in
the multi-purpose tray
Labels
Letter, Legal, Folio,
Oficio, A4, JIS B5,
ISO B5, Executive,
A5, A6
Refer to the Plain paper section
120 to 150 g/m2 (32 to 40 lb)
5 sheets of 75 g/m2 (20 lb) in
the multi-purpose tray
Card stock
Letter, Legal, Folio,
Oficio, A4, JIS B5,
ISO B5, Executive,
A5, A6
Refer to the Plain paper section
60 to 163 g/m2 (16 to 43 lb)
5 sheets of 75 g/m2 (20 lb) in
the multi-purpose tray
Minimum size (custom)
76 x 127 mm (3 x 5 inches)
Maximum size (custom)
215.9 x 356 mm (8.5 x 14 inches)
60 to 163 g/m2
(16 to 43 lb bond )
5 sheets of 75 g/m2 (20 lb) in
the multi-purpose tray
Letter
215.9 x 279 mm (8.5 x 11 inches)
Legal
215.9 x 355.6 mm (8.5 x 14 inches)
Folio
216 x 330 mm (8.5 x 13 inches)
Oficio
215 x 340 mm (8.5 x 13.5 inches)
A4
210 x 297 mm (8.27 x 11.69 inches)
JIS B5
182 x 257 mm (7.18 x 10.12 inches)
ISO B5
176 x 250 mm (6.93 x 9.84 inches)
Executive
184.2 x 266.7 mm (7.25 x 10.5 inches)
A5
148.5 x 210 mm (5.85 x 8.27 inches)
A6
105 x 148.5 mm (4.13 x 5.85 inches)
Envelope Monarch
98.4 x 190.5 mm (3.88 x 7.5 inches)
Envelope COM-10
105 x 241 mm (4.12 x 9.5 inches)
Envelope DL
110 x 220 mm (4.33 x 8.66 inches)
Envelope C5
162 x 229 mm (6.38 x 9.02 inches)
Envelope C6
114 x 162 mm (4.49 x 6.38 inches)
Transparency
Letter, A4
Plain paper
Envelope
a. If media weight is over 24 lb (90 g/m2), use the multi-purpose tray.
b. Maximum capacity may differ depending on media weight, thickness, and environmental conditions.
Note
For duplex printing, A4, Letter, Oficio, Legal, and Folio sizes are supported.
5.2
<Loading print media>
Guidelines for selecting and storing print media
Guidelines for special print media
When selecting or loading paper, envelopes, or other print materials,
keep these guidelines in mind:
Media type
• Always use print media that conform with the specifications listed on
page 5.3.
• Attempting to print on damp, curled, wrinkled, or torn paper can cause
paper jams and poor print quality.
• For the best print quality, use only high quality copier grade paper
specifically recommended for use in laser printers.
• Avoid using the following media types:
- Paper with embossed lettering, perforations, or a texture that is too
smooth or too rough
- Erasable bond paper
- Multi-paged paper
- Synthetic paper and thermally reactive paper
- Carbonless paper and Tracing paper.
• Use of these types of paper could result in paper jams, chemical
smells, and damage to your printer.
• Store print media in its ream wrapper until you are ready to use it.
Place cartons on pallets or shelves, not on the floor. Do not place
heavy objects on top of the paper, whether it is packaged or
unpackaged. Keep it away from moisture or other conditions that can
cause it to wrinkle or curl.
• Store unused print media at temperatures between 15o C and 30o C
(59o F to 86o F). The relative humidity should be between 10% and
70%.
Envelopes
• Store unused print media in a moisture-proof wrap, such as a plastic
container or bag, to prevent dust and moisture from contaminating
your paper.
Guidelines
• Successful printing on envelopes depends upon
the quality of the envelopes. When selecting
envelopes, consider the following factors:
- Weight: The weight of the envelope paper
should not exceed 90 g/m2 (24 lb) or jamming
may occur.
- Construction: Prior to printing, envelopes
should lie flat with less than 6 mm
(0.25 inches) curl, and should not contain air.
- Condition: Envelopes should not be wrinkled,
nicked, or otherwise damaged.
- Temperature: You should use envelopes that
are compatible with the heat and pressure of
the printer during operation.
• Use only well-constructed envelopes with sharp
and well creased folds.
• Do not use stamped envelopes.
• Do not use envelopes with clasps, snaps,
windows, coated lining, self-adhesive seals, or
other synthetic materials.
• Do not use damaged or poorly made envelopes.
• Be sure the seam at both ends of the envelope
extends all the way to the corner of the
envelope.
Acceptable
• Load special media types one sheet at a time through the multipurpose tray to avoid paper jams.
• To prevent print media, such as transparencies and label sheets, from
sticking together, remove them as they print out.
Unacceptable
• Envelopes with a peel-off adhesive strip or with
more than one flap that folds over to seal must
use adhesives compatible with the printer’s
fusing temperature of 200° C (392° F) for
0.1 second. The extra flaps and strips might
cause wrinkling, creasing, or jams, and may
even damage the fuser.
• For the best print quality, position margins no
closer than 15 mm (0.6 inches) from the edges
of the envelope.
• Avoid printing over the area where the
envelope’s seams meet.
5.3
<Loading print media>
Media type
Guidelines
Transparencies
• To avoid damaging the printer, use only
transparencies designed for use in laser printers.
• Transparencies used in the printer must be able
to withstand 200° C (392° F), the printer’s fusing
temperature.
• Place them on a flat surface after removing them
from the printer.
• Do not leave them in the paper tray for long
periods of time. Dust and dirt may accumulate
on them, resulting in spotty printing.
• To avoid smudging caused by fingerprints,
handle them carefully.
• To avoid fading, do not expose printed
transparencies to prolonged sunlight.
• Ensure that transparencies are not wrinkled,
curled, or have any torn edges.
Labels
• To avoid damaging the printer, use only labels
designed for use in laser printers.
• When selecting labels, consider the following
factors:
- Adhesives: The adhesive material should be
stable at 200° C (392° F), the printer’s fusing
temperature.
- Arrangement: Only use labels with no exposed
backing between them. Labels can peel off
sheets that have spaces between the labels,
causing serious jams.
- Curl: Prior to printing, labels must lie flat with
no more than 13 mm (5 inches) of curl in any
direction.
- Condition: Do not use labels with wrinkles,
bubbles, or other indications of separation.
• Make sure that there is no exposed adhesive
material between labels. Exposed areas can
cause labels to peel off during printing, which
can cause paper jams. Exposed adhesive can
also cause damage to printer components.
• Do not run a sheet of labels through the printer
more than once. The adhesive backing is
designed for only a single pass through the
printer.
• Do not use labels that are separating from the
backing sheet or are wrinkled, bubbled, or
otherwise damaged.
Card stock or
custom-sized
materials
Media type
Preprinted
paper
Guidelines
• Letterhead must be printed with heat-resistant
ink that will not melt, vaporize, or release
hazardous emissions when subjected to the
printer’s fusing temperature of 205° C (400° F)
for 0.1 second.
• Letterhead ink must be non-flammable and
should not adversely affect printer rollers.
• Forms and letterhead should be sealed in a
moisture-proof wrapping to prevent changes
during storage.
• Before you load preprinted paper, such as forms
and letterhead, verify that the ink on the paper is
dry. During the fusing process, wet ink can come
off preprinted paper, reducing print quality.
Loading paper
Load the print media you use for the majority of your print jobs in the tray
1. The tray 1 can hold a maximum of 250 sheets of 20 lb plain paper.
You can purchase an optional tray (tray 2) and attach it below the
standard tray to load an additional 250 sheets of paper. For order
information for an optional tray, see page 7.1.
The paper level indicator on the front of the tray 1 and the optional tray
2 shows the amount of paper currently left in the tray. When the tray is
empty, the indicator bar appears at the bottom.
Full
• Do not print on media smaller than 76 mm
(3 inches) wide or 127 mm (5 inches) long.
• In the software application, set margins at least
6.4 mm (0.25 inches) away from the edges of
the material.
5.4
<Loading print media>
Empty
Using the tray 1 or the optional tray 2
1
Press and hold the guide lock, and slide the paper length guide to
locate it in the correct paper size slot.
2
After inserting paper into the tray, adjust the support guide so that it
lightly touches the paper stack.
3
Squeeze the paper width guides, as shown and slide them to the
stack of paper until it lightly touches the side of the stack.
Use the print material you use for the majority of your print jobs in the
tray 1. The tray 1 can hold a maximum of 250 sheets of 80 g/m2 paper.
You can purchase an optional tray 2 and attach it below the tray 1 to load
an additional 250 sheets of paper.
To load paper, pull open the tray and load paper with the side to be
printed on face down.
You can load letterhead paper with the design side face down. The top
edge of the sheet with the logo should be placed at the front of the tray.
Notes
• If you experience problems with paper feed, place one sheet
at a time in the multi-purpose tray.
• You can load previously printed paper. The printed side
should be facing up with an uncurled edge at the front. If you
experience problems with paper feed, turn the paper around.
Note that the print quality is not guaranteed.
Changing the size of the paper in the tray 1
To load longer sizes of paper, such as Legal-sized paper, you need to
adjust the paper guides to extend the paper tray.
3
1
2
4
1
2
3
4
paper length guide
support guide
guide lock
paper width guides
5.5
<Loading print media>
Notes
3
Load the paper with the side to be printed on facing up.
• Do not push the paper width guide far enough to cause the
material to warp.
• If you do not adjust the paper width guide, it may cause paper
jams.
Using the multi-purpose tray
The multi-purpose tray can hold special sizes and types of print material,
such as transparencies, postcards, note cards, and envelopes. It is
useful for single page printing on letterhead or colored paper.
Depending on the media type you are using, keep the following
loading guidelines:
To load paper in the multi-purpose tray:
1
• Envelopes: Flap side down and with the stamp area on the top left
side. If you need to do the printing job with a wrinkled envelopes,
open the rear cover, (see page 5.8.) Push the pressure lever on
each side down.
Open the multi-purpose tray and unfold the multi-purpose tray
extension, as shown.
1
2
1
If you are using paper, flex or fan the edge of the paper stack to
separate the pages before loading.
pressure lever
• Transparencies: Print side up and the top with the adhesive strip
entering the printer first.
• Labels: Print side up and top short edge entering the printer first.
• Preprinted paper: Design side up with the top edge toward the
printer.
• Card stock: Print side up and the short edge entering the printer
first.
For transparencies, hold them by the edges and avoid touching the
print side. Oils from your fingers can cause print quality problems.
• Previously printed paper: Previously printed side down with an
uncurled edge toward the printer.
Note
Make sure that you have not loaded too much print material.
The print material buckles if you load a stack that is too deep or
if you push it in too far.
5.6
<Loading print media>
Caution
This loading procedure is almost the same as the procedure for loading
in the multi-purpose tray, except you load paper sheet-by-sheet in the
tray, send print data to print the first page, and press OK on the control
panel to print each following page.
When you print on special material like envelopes, labels,
transparencies, or cards, the output location should be the
rear cover. Open the rear cover to use it. See page 5.8.
4
5
Squeeze the multi-purpose tray paper width guides and adjust
them to the width of the paper. Do not force too much, or the paper
will be bent, which will result in a paper jam or skew.
1
Load the paper with the side to be printed on facing up.
2
Squeeze the multi-purpose tray paper width guides and adjust
them to the width of the paper. Do not force too much, or the paper
will be bent, which will result in a paper jam or skew.
3
When you print a document, set the paper source to Manual
Feeder and select the appropriate paper size and type in the
software application. See the Software Section.
4
Print a document.
When you print a document, set the paper source and type in the
software application. See the Software Section.
For information about setting the paper source and type on the
control panel, see page 2.3.
6
After printing, fold the multi-purpose tray extension and close the
multi-purpose tray.
Tips on using the multi-purpose tray
• Load only one size of print media at a time in the multi-purpose tray.
• To prevent paper jams, do not add paper when there is still paper in
the multi-purpose tray. This also applies to other types of print media.
• Print media should be loaded face up with the top edge going into the
multi-purpose tray first and be placed in the center of the tray.
• Always load only the print media specified in page 5.1 to avoid paper
jams and print quality problems.
• Flatten any curl on postcards, envelopes, and labels before loading
them into the multi-purpose tray.
• When you print on 76 mm x 127 mm (3 x 5 inches) sized media on
the multi-purpose tray, open the rear cover for straight paper path to
avoid paper jams.
The display shows a message prompting you to load paper and
press OK.
5
• Make sure to open the rear cover when you print on transparencies. If
not, they may tear while exiting the printer.
Press Stop.
The printer picks up the print material and prints. After one page is
printed, the message appears again.
Using manual feed mode
Note
If you do not press the button, after a pause the printer will
automatically pick the print material.
You can manually load a sheet of print material in the multi-purpose tray
if you select Manual Feeder in the Source option from the Paper tab
when you change print settings to print a document. See the Software
Section. Manually loading paper can be helpful when you want to check
the print quality after each page is printed.
6
Insert the next sheet into the multi-purpose tray and press Stop.
Repeat this step for every page to be printed.
5.7
<Loading print media>
Printing to the rear cover (Face up)
Selecting an output location
Using the rear cover, paper comes out of the printer face up.
The printer has two output locations; the rear cover (face up) and the
output tray (face down).
Printing from the multi-purpose tray to the rear cover provides a straight
paper path. Using the rear cover might improve the output quality with
special print media.
To use the rear cover, open it by pulling down.
1
2
1
2
rear cover
output tray
The printer sends output to the output tray by default. To use the output
tray, make sure that the rear cover is closed.
Notes
• If paper coming out of the output tray has problems, such as
excessive curl, try printing to the rear cover.
• To avoid paper jams, do not open or close the rear cover while
the printer is printing.
Caution
The fuser area inside the rear cover of your printer becomes
very hot when in use. Take care when you access this area.
Printing to the output tray (Face down)
The output tray collects paper face down, in the order in which the sheets
were printed. The tray should be used for most print jobs.
5.8
<Loading print media>
6 Basic printing
Printing a document
This chapter includes:
This printer allows you to print from various Windows, Mac OS
applications. The exact steps for printing a document may vary
depending on the application you use.
•
Printing a document
For details about printing, see the Software Section.
•
Canceling a print job
This chapter explains common printing tasks.
Canceling a print job
If the print job is waiting in a print queue or print spooler, such as the
printer group in Windows, delete the job as follows:
1
Click the Windows Start button.
2
For Windows 2000, select Settings and then Printers.
For Windows XP/2003, select Printers and Faxes.
For Windows Vista, select Control Panel > Hardware and Sound >
Printers.
3
Double-click the Xerox Phaser 3435 PCL 6 or Xerox Phaser 3435
PS icon.
4
From the Document menu, select Cancel (Windows 2000/XP/
2003).
Note
You can access this window simply by double-clicking the
printer icon at the bottom right corner of the Windows desktop.
You can also cancel the current job by pressing Start/Stop on the control
panel of your printer.
6.1
<Basic printing>
How to purchase
7 Ordering supplies and
To order Xerox-authorized supplies or accessories, contact your local
Xerox dealer or the retailer where you purchased your printer, or visit
www.xeroxsupplies.com.au
accessories
This chapter provides information on purchasing print cartridges and
accessories available for your printer.
•
Print cartridges
•
Accessories
•
How to purchase
Print cartridges
When the toner runs out, you can order the following types of print
cartridges for your printer:
Type
Yielda
Part number
Standard yield
4,000 pages
CWAA0762
High yield
10,000 pages
CWAA0763
a. Declared yield value in accordance with ISO/IEC 19752.
Accessories
You can purchase and install accessories to enhance your printer’s
performance and capacity.
The following accessories are available for your printer:
Accessory
Description
Part number
Optional
tray
If you are experiencing
frequent paper supply
problems, you can attach an
additional 250 sheet tray.
You can print documents on
various sizes and types of
print materials.
EL300651
Memory
DIMM
Extends your printer’s
memory capacity.
•
• EL300654:
128 MB
• EL300655:
256 MB
7.1
<Ordering supplies and accessories>
8 Maintenance
Cleaning the inside of the printer
This chapter provides information for maintaining your printer and the
print cartridge, as well as suggestions for high-quality and economical
printing.
• Clean the inside manually.
This chapter includes:
Cleaning the inside of the printer manually
•
Printing information page
1
•
Cleaning the printer
Turn the printer off and unplug the power cord. Wait for the printer
to cool down.
•
Maintaining the print cartridge
2
•
Maintenance parts
Open the front cover and pull the print cartridge out. Set it on a
clean flat surface.
There are two methods to clean the inside of the printer:
• Print a cleaning sheet, which can be done from the control panel.
Printing information page
From the printer’s control panel, you can print pages that give detailed
information about the printer. They can be help you maintain your printer.
1
Press Menu until Information appears on the bottom line of the
display and press OK.
2
Press the scroll buttons until the information page you want
appears and press OK.
A page prints out.
Cautions
• To prevent damage to the print cartridge, do not expose it to
light for more than a few minutes. Cover it with a piece of
paper, if necessary.
• Do not touch the green surface underside of the print
cartridge. Use the handle on the cartridge to avoid touching
this area.
Cleaning the printer
During the printing process, paper, toner, and dust particles can
accumulate inside the printer. This buildup can cause print quality
problems, such as toner specks or smearing. Your printer has a cleaning
mode that can correct and prevent these types of problems.
3
Cleaning the outside of the printer
With a dry lint-free cloth, wipe away any dust and spilled toner from
the print cartridge area and the print cartridge cavity.
Clean the cabinet of the printer with a soft, lint-free cloth. You can
dampen the cloth slightly with water, but be careful not to let any water
drip onto or into the printer.
Caution
If your machine or its surrounding is contaminated with toner,
we recommend you to use a cloth or tissue dampened with
water to clean it. Toner blown into the air by a vacuum cleaner
maybe harmful.
Caution
Cleaning the cabinet of the printer with cleaning materials
containing large amounts of alcohol, solvents, or other strong
substances can discolor or crack the cabinet.
Caution
While cleaning the inside of the printer, be careful not to touch
the transfer roller, located underneath the print cartridge. Oil
from your fingers can cause print scan quality problems.
8.1
<Maintenance>
4
Locate the long strip of glass (LSU) inside the top of the cartridge
compartment, and gently swab the glass with a cotton swab
checking to see if dirt turns the cotton black.
• To prevent damage to the print cartridge, do not expose it to light for
more than a few minute.
Expected cartridge life
The print cartridge yield depends on the amount of toner that print jobs
require. Average yield for a new print cartridge is either 10,000 or 4000
standard pages in accordance with the ISO/IEC 19752 standard.
(Average yield for the original print cartridge supplied with the machine
is 4,000 standard pages.) The actual number may also be different
depending on the print density of the pages you print on, and the number
of pages may be affected by operating environment, printing interval,
media type, and media size. If you print a lot of graphics, you may need
to change the cartridge more often.
Saving Toner
5
Reinsert the print cartridge and close the front cover.
6
Plug in the power cord and turn the printer on.
To save toner, press Toner Save on the control panel. The button
backlight turns on.
Using this feature extends the life of the print cartridge and reduce your
cost per page, but it also reduces print quality.
Printing a cleaning sheet
Checking the remaining toner
If you are experiencing blurred, faded, or smeared printouts, you can
clear the problem by printing a cleaning sheet, provided by your printer.
You can print:
You can check the level of toner left in the cartridge.
If you are having print quality problems, this can help you determine if
the problem is caused by low toner.
• OPC Cleaning sheet: cleans the OPC drum of the print cartridge.
• Fuser Cleaning sheet: cleans the fuser unit inside the printer.
This process will produce a page with toner debris, which should be
discarded.
1
Make sure that the printer is turned on with paper loaded in the tray.
2
Press Menu until System Setup appears on the bottom line of the
display and press OK.
3
Press the scroll buttons until Maintenance appears and press OK.
4
When Clean Drum appears, press OK.
1
Press Menu until System Setup appears on the bottom line of the
display press OK.
2
Press the scroll buttons until Maintenance appears and press OK.
3
Press the scroll buttons until Supplies Life appears and press OK.
4
Press the scroll buttons to access Toner Remains and press OK.
The display shows the percentage of the remaining toner.
Note
While the following messages are appearing on the display, the
sub-menu(s) under Supplies Life can be changed:
Or, press the scroll buttons until Clean Drum or Clean Fuser
appears and press OK.
- Invalid Toner, NonGenuine Toner, Replace Toner,
Toner Exhausted
Your printer automatically picks up a sheet of paper from the tray
and prints out a cleaning sheet with dust or toner particles on it.
Maintaining the print cartridge
Print cartridge storage
To get the most from the print cartridge, keep the following guidelines in
mind:
• Do not remove the print cartridge from its package until ready for use.
• Do not refill the print cartridge. The printer warranty does not cover
damage caused by using a refilled cartridge.
• Store print cartridge in the same environment as the printer.
8.2
<Maintenance>
Redistributing print cartridge
Note
If toner gets on your clothing, wipe it off with a dry cloth and
wash clothing in cold water. Hot water sets toner into fabric.
When the print cartridge is near the end of its life:
• White streaks or light printing occurs.
• Toner Low appears on the display.
• The Status Monitor program window appears on the computer telling
you that the toner level is low.
4
Hold the print cartridge by the handle and slowly insert the cartridge
into the opening in the printer.
5
Tabs on the sides of the cartridge and corresponding grooves
within the printer will guide the cartridge into the correct position
until it locks into place completely.
6
Close the front cover. Make sure that the cover is securely closed.
• The Status LED blinks red.
If this happens, you can temporarily reestablish print quality by
redistributing the remaining toner in the cartridge. In some cases, white
streaks or light printing will still occur even after you have redistributed
the toner.
1
Open the front cover.
2
Pull the print cartridge out.
Replacing the print cartridge
When the print cartridge is completely empty:
• Toner Low Replace Toner appears on the display.
• The Smart Panel program window appears on the computer telling
you that the print cartridge is empty.
Cautions
• Avoid reaching too far into the printer. The fusing area may
be hot.
• To prevent damage to the print cartridge, do not expose it to
light for more than a few minutes. Cover it with a piece of
paper, if necessary.
• Do not touch the green surface underside of the print
cartridge. Use the handle on the cartridge to avoid touching
this area.
3
• The Status LED blinks red.
At this stage, the print cartridge needs to be replaced. For order
information for print cartridges, see page 7.1.
1
Open the front cover.
2
Pull the print cartridge out.
Thoroughly roll the cartridge 5 or 6 times to distribute the toner
evenly inside the cartridge.
8.3
<Maintenance>
3
Clearing the Toner Low Replace Toner message
Remove the new print cartridge from its bag.
When the Toner Low Replace Toner message appears you can
configure not to see this message again not to disturb you.
Caution
Do not use sharp objects, such as a knife or scissors, to open
the print cartridge package. They might scratch the drum of
the cartridge.
4
Remove the packing tape and roll the cartridge 5 or 6 items to
distribute the toner.
1
Press Menu until System Setup appears on the bottom line of the
display and press OK.
2
Press the scroll buttons until Maintenance appears and press OK.
3
Press the scroll buttons until CLR Empty MSG. appears and press
OK.
4
Select On and press OK.
5
Now the Toner Low Replace Toner message does not appear but
the Replace Toner message will remain for reminding you that the
new cartridge needs to be installed for quality.
Caution
Once you have selected On, this setting will be permanently
written to the memory of the print cartridge, and this menu will
be disappeared from the Maintenance menu.
Maintenance parts
Thoroughly roll the cartridge to assure maximum copies per
cartridge. Save the box and the plastic bag for shipping.
To avoid print quality and paper feed problems resulting from worn parts
and to maintain your printer in top working condition the following items
will need to be replaced at the specified number of pages or when the
life span of each item has expired.
Cautions
• If toner gets on your clothing, wipe it off with a dry cloth and
wash clothing in cold water. Hot water sets toner into fabric.
• To prevent damage to the print cartridge, do not expose it to
light for more than a few minutes. Cover it with a piece of
paper, if necessary.
• Do not touch the green surface underside of the print
cartridge. Use the handle on the cartridge to avoid touching
this area.
5
Hold the print cartridge by the handle and slowly insert the cartridge
into the opening in the printer.
6
Tabs on the sides of the cartridge and corresponding grooves
within the printer will guide the cartridge into the correct position
until it locks into place completely.
7
Close the front cover. Make sure that the cover is securely closed.
Items
Yield (Average)
Transfer roller
70,000 page
Pick-up roller
150,000 page
Fuser unit
80,000 page
Xerox highly recommends that an authorized service provider, dealer or
the retailer where you bought printer performs this maintenance activity.
The warranty does not cover the replacement of the maintenance parts
after their lifespan.
8.4
<Maintenance>
9 Troubleshooting
Clearing paper jams
Note
When removing paper that is jammed in the printer, if possible
always pull the paper in the direction that it normally moves so
as not to damage internal components. Always pull firmly and
evenly; do not jerk the paper. If the paper tears, ensure that all
fragments of paper are removed; otherwise a jam will occur
again.
This chapter provides helpful information for what to do if you encounter
an error while using your printer.
This chapter includes:
•
Clearing paper jams
•
Troubleshooting checklist
•
Understanding display messages
•
Print cartridge-related messages
•
Solving general printing problems
•
Solving print quality problems
•
Common Windows problems
•
Common PostScript problems
•
Common Linux problems
•
Common Macintosh problems
When a paper jam occurs, the Status LED lights red. Open and close the
front cover. The jammed paper automatically exit the printer.
If the paper does not exit, check the display on the control panel. The
message indicating the corresponding location of the paper jam
appears. Refer to the table below to locate the paper jam and to clear it:
Message
Location of Jam
In the paper feed area
(tray 1, optional tray 2, multipurpose tray)
below
Around the print cartridge
page 9.3
Paper Jam 2
Check Inside
In the paper exit area
page 9.3
Duplex Jam 0
Check Inside
In the duplex area
page 9.4
Duplex Jam 1
Open/Close Door
In the duplex area
page 9.5
Paper Jam 0
Open/Close Door
Paper Jam 1
Open/Close Door
In the paper feed area
In the tray 1
1
9.1
Go To
Pull the tray 1 open.
<Troubleshooting>
2
Remove the jammed paper by gently pulling it straight out. Make
sure that all of the paper is properly aligned in the tray 1.
If the paper does not move when you pull, or if you do not see the
paper in this area, check the fuser area around the print cartridge.
See page 9.3.
3
4
Pull the paper straight up and out.
5
Insert the trays back into the printer. Printing automatically
resumes.
In the multi-purpose tray
Insert the tray 1 into the printer until it snaps into place. Printing
automatically resumes.
1
If the paper is not feeding properly, pull the paper out of the printer.
2
Open and close the front cover to resume printing.
In the optional tray 2
1
Pull the optional tray 2 open.
2
Remove the jammed paper from the printer.
If the paper does not move when you pull, or if you do not see the
paper in this area, stop and go to step 3.
3
Pull tray 1 half-way out.
9.2
<Troubleshooting>
Around the print cartridge
1
2
3
In the paper exit area
Note
1
The fuser area is hot. Take care when removing paper from the
printer.
Open and close the front cover. The jammed paper is automatically
ejected from the printer.
2
Gently pull the paper out of the output tray.
Open the front cover and pull the print cartridge out.
If you do not see the jammed paper or if there is any resistance
when you pull, stop and go to the next step.
Remove the jammed paper by gently pulling it straight out.
Replace the print cartridge and close the front cover. Printing
automatically resumes.
3
Open the rear cover.
4
If you see the jammed paper, push the pressure lever on each side
down and remove the paper. Return the pressure lever to its
original position and skip the step 10.
1
1
pressure lever
If you still do not see the paper, go to the next step.
9.3
<Troubleshooting>
5
Release the blue strap, the rear cover stopper, and fully open the
rear cover, as shown.
8
Pull the jammed paper out.
If the jammed paper does not move when you pull, push the
pressure lever on each side down to loose the paper, and then
remove it.
1
1
2
6
1
2
rear cover stopper
rear cover
Unfold the duplex guide fully.
1
9
pressure lever
Return the lever, door, stopper, and guide to their original position.
10 Close the rear cover. Printing automatically resumes.
In the duplex unit area
1
If the duplex unit is not inserted correctly, paper jam may occur. Make
sure that the duplex unit is inserted correctly.
1
Duplex jam 0
duplex guide
1
7
Pull the duplex unit out of the printer.
While pushing the fuser lever to the right, open the fuser door.
1
1
2
1
2
1
fuser lever
fuser door
9.4
<Troubleshooting>
duplex unit
2
Remove the jammed paper from the duplex unit.
3
Pull the jammed paper out.
If the paper does not come out with the duplex unit, remove the
paper from the bottom of the printer.
Tips for avoiding paper jams
By selecting the correct media types, most paper jams can be avoided.
When a paper jam occurs, follow the steps outlined on page 9.1.
• Follow the procedures on page 5.5. Ensure that the adjustable guides
are positioned correctly.
• Do not overload the tray. Ensure that the paper level is below the
paper capacity mark on the inside wall of the tray.
• Do not remove paper from the tray while your printer is printing.
• Flex, fan, and straighten paper before loading.
• Do not use creased, damp, or highly curled paper.
• Do not mix paper types in a tray.
• Use only recommended print media. See page 5.1.
Duplex jam 1
1
Open the rear cover.
2
Unfold the duplex guide fully.
• Ensure that the recommended print side of print media is facing down
in the tray, or facing up in the multi-purpose tray.
• If paper jams occur frequently when you print on A5-sized paper:
Load the paper into the tray with the long edge facing the front of the
tray.
1
1
duplex guide
In the printer properties window, set the page orientation to be rotated
90 degrees. See the Software Section.
9.5
<Troubleshooting>
Troubleshooting checklist
Understanding display messages
If the printer is not working properly, consult the following checklist. If the
printer does not pass a step, follow the corresponding troubleshooting
suggestions.
Messages appear on the Smart Panel program window or the control
panel display to indicate the printer’s status or errors. Refer to the tables
below to understand the messages’ meaning and correct the problem if
necessary. Messages and their meanings are listed in alphabetical
order.
Condition
Suggested solutions
Make sure that the
Status LED on the
control panel lights
green and Ready is
shown on the
display.
• If the Status LED is off, check the power
cord connection. Check the power switch.
Check the power source by plugging the
power cord into another outlet.
• If the Status LED lights red, check the
display message. See page 9.6.
Print a demo page
to verify that the
printer is feeding
paper correctly. See
page 2.7.
• If a demo page does not print, check the
paper supply in the tray.
• If the paper jams in the printer, see
page 9.1.
• If an error message appears on the
display, see page 9.6.
Check the demo
page to see if it
printed correctly.
If there is a print quality problem, see
page 9.11.
Print a short
document from a
software application
to verify that the
computer and
printer are
connected and are
communicating
correctly.
• If the page does not print, check the cable
connection between the printer and the
computer.
• Check the print queue or print spooler to
see if the printer has been paused.
• Check the software application to ensure
that you are using the proper printer driver
and communication port. If the page is
interrupted during printing, see page 9.9.
If completing the
checklist does not
resolve the printer
problem, check the
following
troubleshooting
sections.
• “Understanding display messages” on
page 9.6.
• “Solving general printing problems” on
page 9.9.
• “Common Windows problems” on
page 9.13.
• “Common Macintosh problems” on
page 9.14.
• “Common PostScript problems” on
page 9.13.
• “Common Linux problems” on page 9.14.
Note
When you call for service, it is very convenient to tell the
service representative the display message.
Message
9.6
Meaning
Suggested solutions
Door Open
The front cover or
rear cover is not
securely latched.
Close the cover until
it locks into place.
Duplex Jam 0
Check Inside
Paper has jammed
during duplex
printing.
Clear the jam. See
page 9.4.
Duplex Jam 1
Open/Close Door
Paper has jammed
during duplex
printing.
Clear the jam. See
page 9.5.
Fuser
Door Open
The fuser door is
not securely latched.
Open the rear cover
and close the fuser
door until it locks into
place.
For the location of
the fuser door, see
page 9.4.
IP Conflict
The network IP
address you have
set is being used by
someone else.
Check the IP
address and reset it if
necessary. See
Software section.
Load Manually
Press Stop Key
The multi-purpose
tray is empty in
manual feed mode.
Load a sheet of print
material and press
Stop.
Low Heat Error
Cycle Power
There is a problem
in the fuser unit.
Unplug the power
cord and plug it back
in. If the problem
persists, please call
for service.
LSU Hsync Error
Cycle Power
A problem has
occurred in the LSU
(Laser Scanning
Unit).
Unplug the power
cord and plug it back
inches. If the
problem persists,
please call for
service.
<Troubleshooting>
Message
Meaning
Suggested solutions
A problem has
occurred in the LSU
(Laser Scanning
Unit).
Unplug the power
cord and plug it back
inches. If the
problem persists,
please call for
service.
Main Motor
Locked
There is a problem
in the main motor.
Open and then close
the front cover.
Open Heat Error
Cycle Power
There is a problem
in the fuser unit.
Unplug the power
cord and plug it back
in. If the problem
persists, please call
for service.
Over Heat Error
Cycle Power
There is a problem
in the fuser unit.
Unplug the power
cord and plug it back
in. If the problem
persists, please call
for service.
Paper Jam 0
Open/Close Door
Paper has jammed
in the feeding area
of the tray.
Clear the jam. See
page 9.1 and
page 9.1.
Paper Jam 1
Open/Close Door
Paper has jammed
in the fuser area.
Clear the jam. See
page 9.3.
Paper Jam 2
Check Inside
Paper has jammed
in the paper exit
area.
Clear the jam. See
page 9.3.
Printing...
The printer is
printing jobs using
the displayed
language.
Complete your
printing.
Ready
The printer is on-line
and ready to printer.
Use your printer.
LSU Motor Error
Cycle Power
Self Diagnostic
LSU
The LSU(Laser
Scanning Unit) in
your printer is
checking some
problems detected.
Please wait a few
minutes.
Self Diagnostic
Temperature
The engine in your
printer is checking
some problems
detected.
Please wait a few
minutes.
Sleeping...
The printer is on
power save mode.
Message
Meaning
Suggested solutions
Tray 1
Paper Empty
There is no paper in
the tray 1.
Load paper in the
tray 1. See page 5.5.
Tray 2
Paper Empty
There is no paper in
the optional tray 2.
Load paper in the
optional tray 2. See
page 5.5.
When data is
received, it switches
to on-line
automatically.
9.7
<Troubleshooting>
Print cartridge-related messages
Message
Meaning
Suggested solutions
Install
Toner
The print cartridge is installed
improperly, or not installed.
Reinstall the print cartridge two or three times. If the problem persists, the print cartridge is
not being detected. Please contact the service representatives.
Invalid
Toner
The print cartridge you have
installed is not for your printer.
Install a Xerox-genuine print cartridge, designed for your printer.
Toner Low
The print cartridge is almost
empty.
Take out the print cartridge and thoroughly shake it. By doing this, you can temporarily
reestablish printing operations.
NonGenuine Toner
The print cartridge installed is not
a Xerox-genuine cartridge.
You can select either Stop or Continue. If you do not select any, the printer will work as
Stop is selected.
If you select Stop, you cannot print until the Xerox-genuine cartridge is installed. However,
you can still print any kind of reports.
If you select Continue, you can keep printing but the quality cannot be guaranteed, and the
product support is no longer provided.
If you want to change the selection, turn the printer off and on to have this message appear
again, and then re-select Stop or Continue.
The print cartridge installed is not
a Xerox-genuine cartridge.
This message appears when you selected Stop at the NonGenuine Toner prompt.
The print cartridge installed is not
a Xerox-genuine cartridge.
This message appears when you selected Continue at the NonGenuine Toner prompt.
Replace Toner
Toner Low
Replace Toner
The toner in the cartridge has run
out.
Install a new Xerox-genuine print cartridge.
You can keep printing but the quality cannot be guaranteed, and the product support is no
longer provided.
You can configure not to see the Toner Low Replace Toner message. See page 8.4.
Replace Toner
The toner in the cartridge has run
out.
This message appears when you turned off the Toner Low Replace Toner message. See
page 8.4.
Stop
NonGenuine Toner
Replace Toner1
NonGenuine Toner
Install the Xerox-genuine print cartridge.
Install the Xerox-genuine print cartridge.
Install a new Xerox-genuine print cartridge.
You can keep printing but the quality cannot be guaranteed, and the product support is no
longer provided.
Toner Exhausted
The lifespan of the print cartridge
is reached.
This message appears when the toner is completely empty and your machine stops
printing. Install the Xerox-genuine print cartridge.
9.8
<Troubleshooting>
Solving general printing problems
Condition
For problems with the operation of your printer, refer to the table for
suggested solutions.
Condition
The printer
does not
print.
Possible cause
Suggested solutions
The printer is not
receiving power.
Check the power cord
connections. Check the power
switch and the power source.
The printer is not
selected as the
default printer.
Select Xerox Phaser 3435 as
your default printer.
The printer cover
is not closed.
Close the printer cover.
Paper is jammed.
Clear the paper jam. See
page 9.1.
No paper is
loaded.
Load paper. See page 5.4.
The print
cartridge is not
installed.
Install the print cartridge.
The printer may
be in manual feed
mode and out of
paper.
Check the display message,
add paper to the multi-purpose
tray, and press OK on the
printer’s control panel.
The connection
cable between
the computer and
the printer is not
connected
properly.
Disconnect the printer cable
and reconnect it.
The connection
cable between
the computer and
the printer is
defective.
If possible, attach the cable to
another computer that is
working properly and try to print
a document. You can also try
using a different printer cable.
The port setting is
incorrect.
Check the Windows printer
setting to make sure that the
print job is sent to the correct
port. If the computer has more
than one port, make sure that
the printer is attached to the
correct one.
The printer
does not
print.
(Continued)
Printer
selects print
materials
from the
wrong paper
source.
Paper does
not feed into
the printer.
Possible cause
Suggested solutions
The printer may
be configured
incorrectly.
Check the printer properties to
ensure that all of the print
settings are correct.
The printer driver
may be
incorrectly
installed.
Reinstall the printer driver; See
the Software Section. Try
printing a test page.
The printer is
malfunctioning.
Check the display message on
the control panel to determine if
the printer is indicating a
system error.
The paper source
selection in the
printer properties
may be incorrect.
For many software
applications, the paper source
selection is found under the
Paper tab within the printer
properties. Select the correct
paper source. See the
Software Section.
Paper has not
been loaded
correctly.
Remove paper from the tray
and reload it correctly.
Check that the paper size
guides are set correctly.
There is too much
paper in the tray.
Remove excess paper from the
tray.
The paper is too
thick.
Use only paper that meets
printer specifications.
Reduce the complexity of the
page(s) or try adjusting the
print quality settings.
Print job is
extremely
slow.
The job may be
very complex.
The printer may
have insufficient
random-access
memory (RAM).
9.9
<Troubleshooting>
To adjust the print quality
settings, reduce the resolution.
If you have set the resolution to
1200 dpi (Best), change it to
600 dpi (Normal). See the
Software Section.
Change the port setting to the
USB or network port to improve
print speed.
Your printer prints A4-sized
paper at 33 ppm and lettersized paper at 35 ppm and your
printer prints A4-sized paper at
17 ipm and letter-sized paper at
18 ipm in the duplex printing
mode.
Install more memory in your
printer. See page 10.1.
Condition
Possible cause
The page layout
is too complex.
Half the page
is blank.
The page
orientation setting
may be incorrect.
The paper size
and the paper
size settings do
not match.
There is too much
paper in the tray.
The paper
keeps
jamming.
The printer
prints, but
the text is
wrong,
garbled, or
incomplete.
An incorrect type
of paper is being
used.
Suggested solutions
Condition
Possible cause
Suggested solutions
Simplify the page layout and
remove any unnecessary
graphics from the document.
The wrong printer
driver was
selected.
Check the application’s printer
selection menu to ensure that
your printer is selected.
Install more memory in your
printer. See page 10.1.
The software
application is
malfunctioning.
Try printing a job from another
application.
The printer
prints, but
the text is
wrong,
garbled, or
incomplete.
(Continued)
Change the page orientation in
your application. See the
Software Section.
Ensure that the paper size in
the printer driver settings
matches the paper in the tray.
Or, ensure that the paper size
in the printer driver settings
matches the paper selection in
the software application
settings you use.
Exit Windows and reboot the
computer. Turn the printer off
and then back on again.
Remove excess paper from the
tray.
If printing on special materials,
use the multi-purpose tray.
Pages print,
but are
blank.
Use only paper that meets
printer specifications.
If printing on special materials,
use the multi-purpose tray.
An incorrect
output method is
being used.
Special print materials, such as
thick paper, should not be
printed using the output tray
(face-down). Use the rear
cover (face-up) instead.
There may be
debris inside the
printer.
Open the front cover and
remove the debris.
If you are under
the DOS
environment, the
font setting for
your machine
may be set
incorrectly.
Change the font setting.
See page 2.5.
The printer cable
is loose or
defective.
Disconnect and reconnect the
printer cable. Try a print job that
you have already printed
successfully. If possible, attach
the cable and printer to another
computer and try a print job
that you know works. Finally,
try a new printer cable.
The operating
system is
malfunctioning.
If printing from Windows (any
version), exit to a DOS prompt
and verify functionality with the
following command: At a C:\
prompt, type Dir LPT1, and
press OK. (This assumes you
are connected to LPT1.)
The
illustrations
print
incorrectly in
Adobe
Illustrator.
The printer
does not
print PDF file
correctly.
Some parts
of graphics,
text, or
illustrations
are missing.
9.10
<Troubleshooting>
The print
cartridge is
defective or out of
toner.
Redistribute the print cartridge.
See page 8.3.
The file may have
blank pages.
Check the file to ensure that it
does not contain blank pages.
Some parts, such
as the controller
or the board, may
be defective.
Contact a service
representative.
The setting in the
software
application is
wrong.
Select Download as Bit Image
in the Advanced Options
window of the graphic
properties. Print the document
again.
Incompatibility
between the PDF
file and the
Acrobat products.
Printing the PDF file as an
image may solve this problem.
Turn on Print As Image from
the Acrobat printing options.
Note: it will take longer to print
when you print a PDF file as an
image.
If necessary, replace the print
cartridge. See page 8.3.
Solving print quality problems
Condition
Vertical lines
Dirt inside of the printer or improper paper loading may reduce print
quality. See the table below to troubleshoot problems.
Condition
AaBbCc
AaBbCc
AaBbCc
AaBbCc
AaBbCc
AaBbCc
AaBbCc
AaBbCc
AaBbCc
AaBbCc
Suggested solutions
If a vertical white streak or faded area appears on
the page:
Light or faded
print
AaBbCc
AaBb
Cc
AaBb
Aa
BbCc
Cc
AaBb
Aa
BbCc
Cc
AaBb
Aa
BbCc
Cc
AaBb
Aa
BbCc
Cc
Toner spots
AaBbCc
AaBbCc
AaBbCc
AaBbCc
AaBbCc
• The toner supply is low. You may be able to
temporarily extend the print cartridge life. See
page 8.3. If this does not improve print quality,
install a new print cartridge.
• The paper may not meet paper specifications
(for example, the paper is too moist or too
rough). See page 5.3.
• If the entire page is light, the print resolution
setting is too light or toner save mode is on.
Adjust the print resolution and toner save mode
in the printer properties. See the Software
Section.
• A combination of faded or smeared defects
may indicate that the printer needs cleaning.
See page 8.1.
• The surface of LSU may be dirty. Clean the
LSU. See page 8.1.
Gray
background
AaBbCc
AaBbCc
AaBbCc
AaBbCc
AaBbCc
Toner smear
• The paper may not meet specifications (for
example, the paper is too moist or too rough).
See page 5.3.
• The transfer roller or paper path may be dirty.
See page 8.1.
Vertical
repetitive
defects
If generally rounded, faded areas occur randomly
on the page:
Dropouts
AaBbCc
AaBbCc
AaBbCc
AaBbCc
AaBbCc
Suggested solutions
AaBbCc
AaBbCc
AaBbCc
AaBbCc
AaBbCc
• A single sheet of paper may be defective. Try
reprinting the job.
• The moisture content of the paper is uneven or
the paper has moist spots on its surface. Try a
different brand of paper. See page 5.3.
• The paper lot is bad. The manufacturing
processes can cause some areas to reject
toner. Try a different kind or brand of paper.
• The print cartridge may be defective. See
“Vertical repetitive defects” on the next page.
• If these steps do not correct the problems,
contact a service representative.
9.11
<Troubleshooting>
If black vertical streaks appear on the page:
• The drum inside the print cartridge has
probably been scratched. Install a new print
cartridge.
If the amount of background shading becomes
unacceptable, the procedures below may fix the
problem.
• Change to lighter weight pages. See page 5.3.
• Check the printer’s environment; very dry (low
humidity) or high humidity (higher than 80%
RH) conditions can increase the amount of
background shading.
• Remove the old print cartridge and install a new
one. See page 8.3.
• Clean the inside of the printer. See page 8.1.
• Check the type and quality. See page 5.2.
• Remove the print cartridge and install a new
one. See page 8.3.
If marks repeatedly appear on the printed side of
the page at even intervals:
• The print cartridge may be damaged. If a
repetitive mark occurs on the page, print a
cleaning sheet several times to clean the
cartridge; see page 8.1. After the printout, if
you still have the same problems, install a new
print cartridge. See page 8.3.
• Parts of the printer may have toner on them. If
the defects occur on the back of the page, the
problem will likely correct itself after a few more
pages.
• The fusing assembly may be damaged.
Contact a service representative.
Condition
Background
scatter
A
Misformed
characters
Page skew
AaBbC
AaBbCcc
AaBbC
AaBbCcc
AaBbCc
Curl or wave
Suggested solutions
Condition
Background scatter results from bits of toner
distributed on the printed page.
• The paper may be too damp. Try printing with a
different batch of paper. Do not open packages
of paper until necessary so that the paper does
not absorb too much moisture.
• If background scatter occurs on an envelope,
change the printing layout to avoid printing over
areas that have overlapping seams on the reverse
side. Printing on seams can cause problems.
• If background scatter covers the entire surface
area of a printed page, adjust the print
resolution through your software application or
via the printer properties window.
Back of
printouts are
dirty
• The transfer roller may be dirty. See page 8.1.
• Check for leaking toner. Clean the inside of the
printer.
Solid color or
Black pages
• The print cartridge may not be installed
properly. Remove the cartridge and reinsert.
• The print cartridge may be defective and need
replacing. Install a new print cartridge.
• The printer may require repair. Contact a
service representative.
A
• If characters are improperly formed and
producing hollowed images, the paper stock
may be too slick. Try a different paper. See
page 5.3.
• If characters are improperly formed and
producing a wavy effect, the scanner unit may
need service. Verify that it also occurs on a
demo page (see page 2.7). For service, contact
a service representative.
Loose toner
• Ensure that the paper is loaded properly.
• Check the paper type and quality. See
page 5.2.
• Ensure that the paper or other material is
loaded correctly and the guides are not too
tight or too loose against the paper stack.
Character
Voids
• Ensure that the paper is loaded properly.
• Check the type and quality. Both high
temperature and humidity can cause paper
curl. See page 5.2.
• Turn over the stack of paper in the tray. Also try
rotating the paper 180° in the tray.
• Try printing to the rear cover (face-up).
A
Horizontal
stripes
Wrinkles or
creases
• Ensure that the paper is loaded properly.
• Check the paper type and quality. See
page 5.2.
• Open the rear cover and try printing to the rear
cover (face-up).
• Turn over the stack of paper in the tray. Also try
rotating the paper 180° in the tray.
AaBbCc
AaBbCc
AaBbCc
AaBbCc
AaBbCc
9.12
Suggested solutions
<Troubleshooting>
• Clean the inside of the printer.
• Check the paper type and quality. See
page 5.2.
• Install a new print cartridge. See page 8.3.
• If the problem persists, the printer may require
repair. Contact a service representative.
Character voids are white areas within characters
that should be solid black:
• If you are using transparencies, try another
type of transparency. Because of the
composition of the transparency, some
character voids may be normal.
• You may be printing on the wrong surface on
the paper. Remove the paper and turn it
around.
• The paper may not meet paper specifications.
See page 5.3.
If horizontally aligned black streaks or smears
appear:
• The print cartridge may be installed improperly.
Remove the cartridge and reinsert.
• The print cartridge may be defective. Install a
new print cartridge. See page 8.3.
• If the problem persists, the printer may require
repair. Contact a service representative.
Condition
Common PostScript problems
Suggested solutions
Curl
The following situations are PostScript language specific and may occur
when several printer languages are being used.
If the printed paper is curled or paper does not
feed into the printer:
• Turn over the stack of paper in the tray. Also try
rotating the paper 180° in the tray.
• Try printing to rear cover.
An unknown
image
repetitively
appears on a
next few sheets
or loose toner,
light print, or
contamination
occurs.
Note
To receive a printed or screen displayed message when
PostScript errors occur, open the Print Options window and
click the desired selection next to the PostScript errors section.
Condition
Your printer is probably being used at an altitude
of 1,000 m (3,281 ft) or above.
The high altitude may affect the print quality such
as loose toner or light imaging. You can set this
option through Printer Settings Utility or
Altitude Adj. in System setup menu. See
page 2.4.
Common Windows problems
Condition
Suggested solutions
“File in Use”
message appears
during installation.
Exit all software applications. Remove all
software from the StartUp Group, then restart
Windows. Reinstall the printer driver.
“Error Writing to
LPTx” message
appears.
• Ensure that the cables are connected
correctly, the printer is on.
• If bi-directional communication is not turned
on in the driver, it will also cause this
message.
“General Protection
Fault”, “Exception
OE”, “Spool32”, or
“Illegal Operation”
messages appear.
Close all other applications, reboot Windows
and try printing again.
“Fail To Print,” “A
printer timeout error
occurred,”
messages appear.
These messages may appear during printing.
Just keep waiting until the printer finishes
printing. If the message appears in standby
mode or after printing has been completed,
check the connection and/or whether an error
has occurred.
Possible cause
Suggested solutions
PostScript file
can not be
printed.
The PostScript
driver may not
be installed
correctly.
• Print a configuration page
and verify that the PostScript
version is available for
printing.
• Install the PostScript driver.
• If problem consists, contact a
service representative.
“Limit Check
Error” message
appears.
The print job
was too
complex.
You might need to reduce the
complexity of the page or install
more memory.
A PostScript
error page
prints.
Print job may
not be
PostScript.
Make sure that the print job is a
PostScript job. Check to see
whether the software
application expected a setup or
PostScript header file to be sent
to the printer.
The optional
tray 2 is not
selected in the
driver.
The printer
driver has not
been
configured to
recognize the
optional tray 2.
Note
Refer to Microsoft Windows 2000/XP/2003 User’s Guide that
came with your PC for further information on Windows error
messages.
9.13
<Troubleshooting>
Open the PostScript driver
properties, select the Device
Settings tab, and set the Tray2
option of the Installable
Options section to Installed.
Common Linux problems
Condition
The printer doesn’t
print.
Common Macintosh problems
Suggested solutions
• Check if the printer driver is installed in your
system. Open Unified Driver Configurator
and switch to the Printers tab in Printers
configuration window to look at the list of
available printers. Make sure that your
machine is displayed on the list. If not,
please, invoke Add new printer wizard to set
up your device.
• Check if the printer is started. Open Printers
configuration and select your machine on
the printers list. Look at the description in
the Selected printer pane. If its status
contains “(stopped)” string, please, press
the Start button. After that normal operation
of the printer should be restored. The
"stopped" status might be activated when
some problems in printing occurred.
• Check if your application has special print
option such as “-oraw”. If “-oraw” is
specified in the command line parameter
then remove it to print properly. For Gimp
front-end, select “print” -> “Setup printer”
and edit command line parameter in the
command item.
I encounter error
“Unable to open
MFP port device
file!” when printing
a document.
Please avoid changing print job parameters
(via LPR GUI, for example) while a print job is
in progress. Known versions of CUPS server
break the print job whenever print options are
changed and then try to restart the job from
the beginning. Since Unified Linux Driver
locks port while printing, the abrupt
termination of the driver keeps the port locked
and therefore unavailable for subsequent print
jobs. If this situation occurred, please, try to
release the port.
When printing a
document over the
network in SuSE
9.2, the printer
does not print.
The CUPS (Common Unix Printing System)
version distributed with SuSE Linux 9.2
(cups-1.1.21) has a problem with IPP
(Internet Printing Protocol) printing. Use the
socket printing instead of IPP or install later
version of CUPS (cups-1.1.22 or higher).
Condition
Suggested solutions
The printer does not
print PDF file correctly.
Some parts of graphics,
text, or illustrations are
missing.
Incompatibility between the PDF file and
the Acrobat products:
Printing the PDF file as an image may
solve this problem. Turn on Print As
Image from the Acrobat printing options.
Note: it will take longer to print when you
print a PDF file as an image.
The document has
printed, but the print job
has not disappeared
from the spooler in Mac
OS 10.3.2.
Update your Mac OS to OS 10.3.3 or
higher.
When print a document
in Macintosh with
Acrobat Reader 6.0 or
higher, colors print
incorrectly.
9.14
<Troubleshooting>
The resolution setting in the printer driver
may not be matched with that in Acrobat
Reader.
Make sure that the resolution setting in
your printer driver matches that in
Acrobat Reader.
10 Installing accessories
Installing a memory DIMM
Your printer has a dual in-line memory module (DIMM) slot. Use this
DIMM slot to install additional memory.
Your printer is a full-featured laser printer that has been optimized to
meet most of your printing needs. Recognizing that each user may have
different requirements, however, Xerox makes several accessories
available to enhance the printer’s capabilities.
Phaser 3435/DN has 64 MB of memory which can be expanded to
320 MB.
This chapter includes:
•
Precautions when installing accessories
•
Installing a memory DIMM
For order information for optional memory DIMM’s, see page 7.1.
1
Turn the printer power off and unplug all cables from the printer.
2
Grasp the control board cover and slide toward you to open it.
Precautions when installing accessories
Disconnect the power cord:
Never remove the control board cover while the power is being supplied.
To avoid the possibility of an electrical shock, always disconnect the
power cord when installing or removing ANY internal or external
accessories.
1
Discharge static electricity:
1
The control board and internal accessories (network interface card and
memory DIMM) are sensitive to static electricity. Before installing or
removing an internal accessories, discharge static electricity from your
body by touching something metal, such as the metal back plate on any
device plugged into a grounded power source. If you walk round before
finishing installation, discharge any static electricity once again.
3
control board cover
Completely open the latch on each side of the DIMM slot.
1
1
4
10.1
latch
Take out a new memory DIMM from the plastic bag.
<Installing accessories>
5
Setting the memory in the PostScript printer
properties
Holding the memory DIMM by the edges, align the notches on the
memory DIMM with the grooves on the memory DIMM slot.
After installing the memory DIMM, you need to select it in the printer
properties of the PostScript printer driver so that you can use it.
1
Make sure that the PostScript printer driver is installed in your
computer. To installing the PostScript printer driver, you need to
select Custom and put a check mark on the PostScript printer
driver. See the Software Section.
2
Click the Windows Start menu.
3
For Windows 2000, select Settings and then Printers.
For Windows XP/2003, select Printers and Faxes.
6
For Windows Vista, select Control Panel -> Hardware and Sound
-> Printers.
Push the DIMM straight into the DIMM slot until it snaps into place.
Make sure the latches fit over the notches located on either side of
the DIMM.
7
Replace the control board cover.
8
Reconnect the power cord and printer cable, and turn the printer
on.
10.2
4
Select the Xerox Phaser 3435 printer.
5
Click the right mouse button on the printer icon and select
Properties.
6
For Windows 2000/XP/2003/Vista, select Device Settings tab.
7
Select the amount of memory you installed from Printer Memory in
the Installable Option section.
8
Click OK.
<Installing accessories>
11 Specifications
Item
This chapter includes:
•
Memory
• 64 MB (Max 320 MB)
• 32, 128, or 256 MB optional memory
available.
• Use only the Xerox-approved DIMM.
Fonts
1 bitmap, 45 scalable, 136 PostScript3 fonts
Interface
• IEEE 1284 Bidirectional Parallel Standard
- Modes supported: Compatible, Nibble, Byte,
ECP
Printer specifications
Printer specifications
Item
Specifications and Description
Model name
Phaser 3435/DN
Printing speeda
33 ppm (A4); 35 ppm (Letter)
Duplex: 17 ipm (A4); 17.5 ipm (Letter)
Resolution
Up to 1200 x 1200 dpi effective output
Warm-up time
Less than 15 seconds
First print out time
Standby mode: 8.5 seconds
Sleep mode: 25 seconds
Power rating
110 - 127 VAC or 220 - 240 VAC
See the Rating label on the machine for the
correct voltage, frequency(hertz) and type of
current for your machine.
Power
consumption
Average: 400 W
Power save mode: Less than 11 W
Noise levelb
Standby mode: Less than 25dBA
Printing mode: Less than 54 dBA
Print cartridge lifec
• Starter Print cartridge: 4,000 pages
• Standard: 4,000 pages
• High yield: 10,000 pages
(Declared yield value in accordance with ISO/
IEC 19752.)
Duty cycle
Monthly: Up to 80,000 pages
Weight
Gross: 15.62 Kg / Net: 12.7 Kg
Package weight
Paper: 1.8 Kg, Plastic: 0.52 Kg
External
dimensions
(W x D x H)
400 x 435 x 314 mm (15.7 x 17.1 x
12.4 inches)
Operating
environment
Temperature: 10 ~ 32° C (50 ~ 90° F)
Humidity: 20 ~ 80% RH
Printer language
PCL 6d, PostScript 3, IBM ProPrinter, EPSON,
SPL
Specifications and Description
• USB Interface Standard
- USB 2.0 compliant
- 480 Mbps 1 port
• Network Interface
- 10/100 Base TX
OS compatibilitye
• Windows 2000/XP/2003./Vista
• Various Linux OS.
• Mac 10.3 ~ 10.5
Options
250-sheet tray
a. Print speed will be affected by operating system used, computing performance, application software, connection method, media type, media size, and
job complexity.
b. Sound pressure Level, ISO7779
c. The number of pages may be affected by operating environment, printing interval, media type, and media size.
d. Compatible with PCL6 Version 2.1
e. Please visit www.xerox.com/office/support to download the latest software version.
11.1
<Specifications>
INDEX
A
L
accessories
installing
memory DIMM 10.1
order information 7.1
Linux problems 9.14
loading paper
multi-purpose tray 5.6
tray 1/optional tray 2 5.5
C
M
cleaning
drum 8.2
inside 8.1
outside 8.1
cleaning sheet, print 8.2
component location 1.2
control panel
menus 2.1
status LED 1.4
Macintosh problems 9.14
manual feed mode 5.7
memory DIMM, install 10.1
multi-purpose tray 5.6
D
demo page, print 2.7
DIMM, install 10.1
display language, change
control panel 2.7
drum, clean 8.2
N
network setup
802.1x 4.3
CentreWare IS 4.3
EtherTalk 4.2
operating systems 4.1
TCP/IP 4.2
O
output location, select 5.8
output tray 5.8
E
error messages 9.6
H
high altitude 9.13
I
installing accessories
memory 10.1
J
jam, clear 9.1
specifications 5.2
paper type
setting 2.3
specifications 5.2
PostScript problems 9.13
print cartridge
checkig remaining toner 8.2
cleaning 8.2
redistributing 8.3
replacing 8.3, 8.4
print quality problems, solve 9.11
printing
demo page 2.7
problem, solve
checklist 9.6
error messages 9.6
Linux 9.14
Macintosh 9.14
paper jams 9.1
printing 9.9
printing quality 9.11
PS errors 9.13
Windows 9.13
Q
quality problems 9.11
R
P
paper guidelines 5.3
paper jam, clear
around the print cartridge 9.3
duplex area 9.4
multi-purpose tray 9.2
optional tray 2 9.2
paper exit area 9.3
tray 1 9.1
paper level indicator 5.4
paper load
multi-purpose tray 5.6
tray 1/optional tray 2 5.5
paper size
setting 2.3
1
rear cover, use 5.8
replacement parts 8.4
replacing, print cartridge 8.3, 8.4
S
special print media, guidelines 5.3
specification, printer 11.1
status LED 1.4
supplies
checking life 8.2
order information 7.1
system requirements
Mac OS 3.2
Windows 3.2
T
toner save mode, use 2.7
W
Windows problems 9.13
2
Software section
Software section
SOFTWARE SECTION
CONTENTS
Chapter 1:
INSTALLING PRINTER SOFTWARE
IN
WINDOWS
Installing Printer Software ........................................................................................................ 4
Installing Software for Local Printing ................................................................................. 4
Installing Software for Network Printing ............................................................................. 7
Reinstalling Printer Software ................................................................................................... 10
Removing Printer Software ..................................................................................................... 10
Chapter 2:
USING SETIP
Installing SetIP ..................................................................................................................... 11
Using SetIP .......................................................................................................................... 11
Chapter 3:
BASIC PRINTING
Printing a Document .............................................................................................................. 12
Printing to a file (PRN) .......................................................................................................... 13
Printer Settings ..................................................................................................................... 13
Layout Tab .................................................................................................................. 14
Paper Tab .................................................................................................................... 14
Graphics Tab ............................................................................................................... 15
Extras Tab ................................................................................................................... 16
Troubleshooting Tab ..................................................................................................... 17
Printer Tab .................................................................................................................. 17
Using a Favorite Setting ................................................................................................ 17
Using Help ................................................................................................................... 17
Chapter 4:
ADVANCED PRINTING
Printing Multiple Pages on One Sheet of Paper (N-Up Printing) ..................................................... 18
Printing Posters ..................................................................................................................... 19
Printing Booklets .................................................................................................................. 19
1
Printing on Both Sides of Paper ............................................................................................... 20
Printing a Reduced or Enlarged Document ................................................................................ 20
Fitting Your Document to a Selected Paper Size ......................................................................... 20
Using Watermarks ................................................................................................................. 21
Using an Existing Watermark ......................................................................................... 21
Creating a Watermark ................................................................................................... 21
Editing a Watermark ..................................................................................................... 21
Deleting a Watermark ................................................................................................... 21
Using Overlays ...................................................................................................................... 22
What is an Overlay? ...................................................................................................... 22
Creating a New Page Overlay ......................................................................................... 22
Using a Page Overlay .................................................................................................... 22
Deleting a Page Overlay ................................................................................................ 22
Chapter 5:
USING WINDOWS POSTSCRIPT DRIVER
Printer Settings ..................................................................................................................... 23
Advanced .................................................................................................................. 23
Using Help ................................................................................................................... 23
Chapter 6:
USING UTILITY APPLICATIONS
Using Printer Settings Utility ................................................................................................... 24
Using Onscreen Help ..................................................................................................... 24
Opening the Troubleshooting Guide ......................................................................................... 24
Changing the Status Monitor Program Settings .......................................................................... 24
Chapter 7:
SHARING
THE
PRINTER LOCALLY
Setting Up a Host Computer ................................................................................................... 25
Setting Up a Client Computer .................................................................................................. 25
2
Chapter 8:
USING YOUR PRINTER
IN
LINUX
Getting Started ..................................................................................................................... 26
Installing the Unified Linux Driver ............................................................................................ 26
Installing the Unified Linux Driver ................................................................................... 26
Uninstalling the Unified Linux Driver ............................................................................... 27
Using the Unified Driver Configurator ....................................................................................... 28
Opening the Unified Driver Configurator .......................................................................... 28
Printers Configuration ................................................................................................... 28
Ports Configuration ....................................................................................................... 29
Configuring Printer Properties ................................................................................................. 29
Printing a Document .............................................................................................................. 30
Printing from Applications .............................................................................................. 30
Printing Files ................................................................................................................ 30
Chapter 9:
USING YOUR PRINTER
WITH A
MACINTOSH
Installing printer driver for Macintosh ....................................................................................... 31
Uninstalling the printer driver .................................................................................................. 31
Setting Up the Printer ............................................................................................................ 32
For a Network-connected Macintosh ................................................................................ 32
For a USB-connected Macintosh ..................................................................................... 32
Installable Options ................................................................................................................. 33
Printing ................................................................................................................................ 33
Printing a Document ..................................................................................................... 33
Changing Printer Settings .............................................................................................. 34
Printing Multiple Pages on One Sheet of Paper .................................................................. 35
Duplex Printing ............................................................................................................ 35
3
1
Typical Installation
Installing Printer
Software in Windows
This is recommended for most users. All components necessary
for printer operations will be installed.
This chapter includes:
• Installing Printer Software
1
Make sure that the printer is connected to your computer
and powered on.
2
Insert the supplied CD-ROM into your CD-ROM drive.
The CD-ROM should automatically run, and an installation
window appears.
• Reinstalling Printer Software
• Removing Printer Software
If the installation window does not appear, click Start and
then Run. Type X:\Setup.exe, replacing “X” with the
letter which represents your drive and click OK.
If you use Windows Vista, click Start → All programs →
Accessories → Run, and type X:\Setup.exe.
Installing Printer Software
If the AutoPlay window appears in Windows Vista, click
Run Setup.exe in Install or run program field, and
click Continue in the User Account Control window.
You can install the printer software for local printing or network
printing. To install the printer software on the computer,
perform the appropriate installation procedure depending on
the printer in use.
A printer driver is software that lets your computer
communicate with your printer. The procedure to install drivers
may differ depending on the operating system you are using.
All applications should be closed on your PC before beginning
installation.
Installing Software for Local Printing
A local printer is a printer directly attached to your computer
using the printer cable supplied with your printer, such as a USB
or parallel cable. If your printer is attached to a network, skip
this step and go to "Installing Software for Network Printing" on
page 7.
You can install the printer software using the typical or custom
method.
3
Click Install Software.
4
Select Typical installation for a local printer. Click
Next.
NOTE: If the “New Hardware Wizard” window appears during
the installation procedure, click
in the upper right corner of
the box to close the window, or click Cancel.
4
Installing Printer Software in Windows
Custom Installation
NOTE: If your printer is not already connected to the
computer, the following window will appear.
You can choose individual components to install.
1
Make sure that the printer is connected to your computer
and powered on.
2
Insert the supplied CD-ROM into your CD-ROM drive.
The CD-ROM should automatically run, and an installation
window appears.
If the installation window does not appear, click Start and
then Run. Type X:\Setup.exe, replacing “X” with the
letter which represents your drive and click OK.
If you use Windows Vista, click Start → All programs →
Accessories → Run, and type X:\Setup.exe.
If the AutoPlay window appears in Windows Vista, click
Run Setup.exe in Install or run program field, and
click Continue in the User Account Control window.
• After connecting the printer, click Next.
• If you don’t want to connect the printer at this time, click
Next, and No on the following screen. Then the installation
will start and a test page will not be printed at the end of the
installation.
• The installation window that appears in this User’s
Guide may differ depending on the printer and
interface in use.
5
After the installation is finished, a window asking you to
print a test page appears. If you choose to print a test
page, select the checkbox and click Next.
Otherwise, just click Next and skip to step 7.
6
If the test page prints out correctly, click Yes.
3
Click Install Software.
7
If not, click No to reprint it.
Click Finish.
4
Select Custom installation. Click Next.
NOTE: After setup is complete, if your printer driver doesn’t
work properly, reinstall the printer driver. See "Reinstalling
Printer Software" on page 10.
5
Installing Printer Software in Windows
5
6
Select your printer and click Next.
Select the components to be installed and click Next.
NOTE: You can change the desired installation folder by
NOTE: If your printer is not already connected to the
computer, the following window will appear.
clicking [Browse].
7
After the installation is finished, a window asking you to
print a test page appears. If you choose to print a test
page, select the checkbox and click Next.
Otherwise, just click Next and skip to step 9.
8
If the test page prints out correctly, click Yes.
9
If not, click No to reprint it.
Click Finish.
• After connecting the printer, click Next.
• If you don’t want to connect the printer at this time, click
Next, and No on the following screen. Then the installation
will start and a test page will not be printed at the end of the
installation.
• The installation window that appears in this User’s
Guide may differ depending on the printer and
interface in use.
6
Installing Printer Software in Windows
Installing Software for Network Printing
4
Select Typical installation for a network printer. Click
Next.
5
The list of printers available on the network appears. Select the
printer you want to install from the list and then click Next.
When you connect your printer to a network, you must first
configure the TCP/IP settings for the printer. After you have
assigned and verified the TCP/IP settings, you are ready to
install the software on each computer on the network.
You can install the printer software using the typical or custom
method.
Typical Installation
This is recommended for most users. All components necessary
for printer operations will be installed.
1
Make sure that the printer is connected to your network
and powered on. For details about connecting to the
network, see the supplied printer’s User’s Guide.
2
Insert the supplied CD-ROM into your CD-ROM drive.
The CD-ROM should automatically run, and an installation
window appears.
If the installation window does not appear, click Start and
then Run. Type X:\Setup.exe, replacing “X” with the
letter which represents your drive and click OK.
If you use Windows Vista, click Start → All programs →
Accessories → Run, and type X:\Setup.exe.
If the AutoPlay window appears in Windows Vista, click
Run Setup.exe in Install or run program field, and
click Continue in the User Account Control window.
• If you do not see your printer on the list, click Update to
refresh the list, or select Add TCP/IP Port to add your
printer to the network. To add the printer to the network,
enter the port name and the IP address for the printer.
To verify your printer’s IP address or the MAC address, print
a Network Configuration page.
• To find a shared network printer (UNC Path), select Shared
Printer [UNC] and enter the shared name manually or find
a shared printer by clicking the Browse button.
3
NOTE: If you cannot find your machine in network, please turn
off the firewall and click Update.
For Windows operating system, click Start → Control Panel
and start windows firewall, and set this option unactivated. For
other operating system, refer to its on-line guide.
Click Install Software.
6
After the installation is finished, a window asking you to
print a test page appears. If you choose to print a test
page, select the checkbox and click Next.
Otherwise, just click Next and skip to step 8.
7
If the test page prints out correctly, click Yes.
8
If not, click No to reprint it.
Click Finish.
7
Installing Printer Software in Windows
4
Select Custom installation. Click Next.
5
The list of printers available on the network appears.
Select the printer you want to install from the list and then
click Next.
NOTE: After setup is complete, if your printer driver doesn’t
work properly, reinstall the printer driver. See "Reinstalling
Printer Software" on page 10.
Custom Installation
You can choose individual components to install and set a
specific IP address.
1
Make sure that the printer is connected to your network
and powered on. For details about connecting to the
network, see the supplied printer’s User’s Guide.
2
Insert the supplied CD-ROM into your CD-ROM drive.
The CD-ROM should automatically run, and an installation
window appears.
If the installation window does not appear, click Start and
then Run. Type X:\Setup.exe, replacing “X” with the
letter which represents your drive and click OK.
If you use Windows Vista, click Start → All programs →
Accessories → Run, and type X:\Setup.exe.
If the AutoPlay window appears in Windows Vista, click
Run Setup.exe in Install or run program field, and
click Continue in the User Account Control window.
• If you do not see your printer on the list, click Update to
refresh the list, or select Add TCP/IP Port to add your
printer to the network. To add the printer to the network,
enter the port name and the IP address for the printer.
To verify your printer’s IP address or the MAC address, print
a Network Configuration page.
3
• To find a shared network printer (UNC Path), select Shared
Printer [UNC] and enter the shared name manually or find
a shared printer by clicking the Browse button.
Click Install Software.
NOTE: If you cannot find your machine in network, please turn
off the firewall and click Update.
For Windows operating system, click Start → Control Panel
and start windows firewall, and set this option unactivated. For
other operating system, refer to its on-line guide.
8
Installing Printer Software in Windows
To install this software on a server, select the Setting up
this printer on a server checkbox.
TIP: If you want to set a specific IP address on a specific
network printer, click the Set IP Address button. The Set IP
Address window appears. Do as follows:
8
After the installation is finished, a window asking you to
print a test page appears. If you choose to print a test
page, select the checkbox and click Next.
Otherwise, just click Next and skip to step 10.
9
If the test page prints out correctly, click Yes.
If not, click No to reprint it.
10 Click Finish.
NOTE: After setup is complete, if your printer driver doesn’t
work properly, reinstall the printer driver. See "Reinstalling
Printer Software" on page 10.
a. Select a printer to be set with a specific IP address from the
list.
b. Configure an IP address, subnet mask, and gateway for the
printer manually and click Configure to set the specific IP
address for the network printer.
c. Click Next.
6
Select the components to be installed and click Next.
7
You can also change the printer name, set the printer to be
shared on the network, set the printer as the default printer,
and change the port name of each printer. Click Next.
9
Installing Printer Software in Windows
• After connecting the printer, click Next.
• If you don’t want to connect the printer at this time, click
Next, and No on the following screen. Then the installation
will start and a test page will not be printed at the end of the
installation.
• The reinstallation window that appears in this User’s
Guide may differ depending on the printer and
interface in use.
Reinstalling Printer Software
You can reinstall the software if installation fails.
1 Start Windows.
2
3
4
From the Start menu select Programs or All Programs
→ your printer driver name → Maintenance.
Select Repair and click Next.
5
The list of printers available on the network appears.
Select the printer you want to install from the list and then
click Next.
Select the components you want to reinstall and click
Next.
If you installed the printer software for local printing
and you select your printer driver name, the window
asking you to print a test page appears. Do as follows:
a. To print a test page, select the check box and click
Next.
b. If the test page prints out correctly, click Yes.
6
If it doesn’t, click No to reprint it.
When the reinstallation is done, click Finish.
Removing Printer Software
• If you do not see your printer on the list, click Update to
refresh the list, or select Add TCP/IP Port to add your
printer to the network. To add the printer to the
network, enter the port name and the IP address for the
printer.
1
2
3
• To find a shared network printer (UNC Path), select
Shared Printer [UNC] and enter the shared name
manually or find a shared printer by clicking the Browse
button.
4
5
You will see a component list so that you can reinstall any
item individually.
NOTE: If your printer is not already connected to the
6
computer, the following window will appear.
Start Windows.
From the Start menu select Programs or All Programs
→ your printer driver name → Maintenance.
Select Remove and click Next.
You will see a component list so that you can remove any
item individually.
Select the components you want to remove and then click
Next.
When your computer asks you to confirm your selection,
click Yes.
The selected driver and all of its components are removed
from your computer.
After the software is removed, click Finish.
10
Installing Printer Software in Windows
2
Using SetIP
5
Click Next.
6
Click Finish.
• Installing SetIP
• Using SetIP
Installing SetIP
1
Make sure that the printer is connected to your computer
and powered on.
2
Insert the supplied CD-ROM into your CD-ROM drive.
The CD-ROM should automatically run, and an installation
window appears.
Using SetIP
If the installation window does not appear, click Start and
then Run. Type X:\Setup.exe, replacing “X” with the
letter which represents your drive and click OK.
1
From the Windows Start menu, select Programs or All
Programs Æ your printer driver name Æ SetIP Æ
SetIP.
The program automatically detects and displays new
and configured print servers on your network.
3
4
Click Install SetIP Utility(Optional).
Click Next.
2 Select the name of your printer and click
cannot find your printer name, click
. If you
to refresh
the list.
NOTES:
• To confirm the MAC address, see the NETWORK PRINTER
CARD TEST PAGE. The NETWORK PRINTER CARD TEST
PAGE will be printed after the Configuration Page.
• The refreshed list doesn’t show your printer, click
enter
your network printer card’s IP address, subnet mask, default
gateway, and then click Apply.
11
Using SetIP
3 Click OK to confirm the settings.
4 Click Exit to close the SetIP program.
3
1
2
Basic Printing
This chapter explains the printing options and common printing
tasks in Windows.
Open the document you want to print.
Select Print from the File menu. The Print window is
displayed. It may look slightly different depending on your
application.
The basic print settings are selected within the Print
window. These settings include the number of copies and
print range.
This chapter includes:
• Printing a Document
• Printer Settings
- Layout Tab
- Paper Tab
Make sure that your
printer is selected.
- Graphics Tab
- Extras Tab
- Troubleshooting Tab
- Printer Information Page
- Using a Favorite Setting
- Using Help
3
Printing a Document
4
NOTES:
• Your printer driver Properties window that appears in this
User’s Guide may differ depending on the printer in use.
However the composition of the printer properties window is
similar.
• Check the Operating System(s) that are compatible
with your printer. Please refer to the OS Compatibility
section of Printer Specifications in your Printer User’s
Guide.
• If you need to know the exact name of your printer, you can
check the supplied CD-ROM.
5
6
The following procedure describes the general steps required
for printing from various Windows applications. The exact steps
for printing a document may vary depending on the application
program you are using. Refer to the User’s Guide of your
software application for the exact printing procedure.
12
Basic Printing
Select your printer driver from the Name drop-down
list.
To take advantage of the printer features provided by your
printer driver, click Properties or Preferences in the
application’s Print window. For details, see "Printer
Settings" on page 13.
If you see Setup, Printer, or Options in your Print
window, click it instead. Then click Properties on the next
screen.
Click OK to close the printer properties window.
To start the print job, click OK or Print in the Print
window.
Printing to a file (PRN)
Printer Settings
You will sometimes need to save the print data as a file for your
purpose.
You can use the printer properties window, which allows you to
access all of the printer options you need when using your
printer. When the printer properties are displayed, you can
review and change the settings needed for your print job.
To create a file:
1 Check the Print to file box at the Print window.
Your printer properties window may differ, depending on your
operating system. This Software User’s Guide shows the
Properties window for Windows XP.
Your printer driver Properties window that appears in this
User’s Guide may differ depending on the printer in use.
If you access printer properties through the Printers folder, you
can view additional Windows-based tabs (refer to your
Windows User’s Guide) and the Printer tab (see "Printer
Information Page" on page 17).
NOTES:
2
• Most Windows applications will override settings you specify
in the printer driver. Change all print settings available in the
software application first, and change any remaining settings
using the printer driver.
• The settings you change remain in effect only while you are
using the current program. To make your changes
permanent, make them in the Printers folder.
• The following procedure is for Windows XP. For other
Windows OS, refer to the corresponding Windows User's
Guide or online help.
1. Click the Windows Start button.
2. Select Printers and Faxes.
3. Select your printer driver icon.
4. Right-click on the printer driver icon and select
Printing Preferences.
5. Change the settings on each tab, click OK.
Select the folder and assign a name of the file and then
click OK.
13
Basic Printing
Layout Tab
Paper Tab
The Layout tab provides options to adjust how the document
appears on the printed page. The Layout Options includes
Multiple Pages per Side and Poster Printing. See "Printing
a Document" on page 12 for more information on accessing
printer properties.
Use the following options to set the basic paper handling
specifications when you access the printer properties. See
"Printing a Document" on page 12 for more information on
accessing printer properties.
Click the Paper tab to access various paper properties.
1
1
2
2
3
4
5
6
Paper Orientation
1 Copies
Copies allows you to choose the number of copies to be printed.
You can select 1 to 999 copies.
Paper Orientation allows you to select the direction in which
information is printed on a page.
• Portrait prints across the width of the page, letter style.
• Landscape prints across the length of the page, spreadsheet
style.
• Rotate allows you to rotate the page the selected degrees
Portrait
2 Size
Size allows you to set the size of paper you loaded in tray.
If the required size is not listed in the Size box, click Custom.
When the Custom Paper Setting window appears, set the paper
size and click OK. The setting appears in the list so that you can
select it.
Landscape
Layout Options
Layout Options allows you to select advanced printing options.
You can choose Multiple Pages per Side and Poster Printing.
• For details, see "Printing Multiple Pages on One Sheet of Paper
(N-Up Printing)" on page 18.
• For details, see "Printing Posters" on page 19
Double-sided Printing
Double-sided Printing allows you to print on both sides of
paper. If this option does not appear, your printer does
not have this feature.
• For details, see "Printing on Both Sides of Paper" on page 20.
14
Basic Printing
Graphics Tab
3 Source
Make sure that Source is set to the corresponding paper tray.
Use Manual Feeder when printing on special materials like
envelopes and transparencies. You have to load one sheet at a
time into Manual Tray or Multi-Purpose Tray.
If the paper source is set to Auto Selection, the printer
automatically picks up print material in the following tray order:
Manual Tray or Multi-Purpose Tray (Tray1), Tray2, optional Tray n.
Use the following Graphic options to adjust the print quality for
your specific printing needs. See "Printing a Document" on
page 12 for more information on accessing printer properties.
Click the Graphic tab to display the properties shown below.
4 Type
Set Type to correspond to the paper loaded in tray from which
you want to print. This will let you get the best quality printout. If
not, print quality may not be acheived as you want.
Cotton: 20 lb to 24 lb (75~90 g/m2) cotton paper such as Gilbert
25 % and Gilbert 100 %.
Plain Paper: Normal plain paper. Select this type if your printer is
monochrome and printing on the 16 lb (60 g/m2) cotton paper.
Recycled Paper: 20 lb to 24 lb (75~90 g/m2) recycled paper.
Color Paper: 20 lb to 24 lb (75~90 g/m2) color-backgrounded
paper.
5 First Page
This property allows you to print the first page using a different
paper type from the rest of the document. You can select the
paper source for the first page.
For example, load thick stock for the first page into the Multipurpose Tray, and plain paper into Tray n. Then, select Tray n in
the Source option and Multi-Purpose Tray in the First Page
option. If this option does not appear, your printer does
not have this feature.
Resolution
The Resolution options you can select may vary
depending on your printer model. The higher the setting,
the sharper the clarity of printed characters and graphics. The
higher setting also may increase the time it takes to print a
document.
Image Mode
6 Scaling Printing
Scaling Printing allows you to automatically or manually scale
your print job on a page. You can choose from None, Reduce/
Enlarge, and Fit to Page.
• For details, see "Printing a Reduced or Enlarged Document" on
page 20.
• For details, see "Fitting Your Document to a Selected Paper
Size" on page 20.
The available options are Normal and Text Enhance. Some
printers do not support this feature.
• Printer Setting: If you select this option, this feature is
determined by the setting you’ve made on the control panel of
the printer.
• Normal: This setting is for normal documents.
• Text Enhancement: Image Mode allows the user to enhance
printouts.
Toner Save Mode
Selecting this option extends the life of your print cartridge and
reduces your cost per page without a significant reduction in print
quality.
• Printer Setting: If you select this option, this feature is
determined by the setting you’ve made on the control panel of
the printer.
• On: Select this option to allow the printer to use less toner on
each page.
• Off: If you don’t need to save toner when printing a document,
select this option.
15
Basic Printing
Advanced Options
Extras Tab
You can set advanced settings by clicking the Advanced
Options button.
• TrueType Options: This option determines what the driver
tells the printer about how to image the text in your document.
Select the appropriate setting according to the status of your
document.
- Download as Outline: When this option is selected, the
driver will download any TrueType fonts that are used in your
document not already stored (resident) on your printer. If,
after printing a document, you find that the fonts did not print
correctly, choose Download as bit image and resubmit your
print job. The Download as bit image setting is often useful
when printing Adobe. This feature is available only
when you use the PCL printer driver.
- Download as Bitmap: When this option is selected, the
driver will download the font data as bitmap images.
Documents with complicated fonts, such as Korean or
Chinese, or various other fonts, will print faster in this setting.
- Print as Graphics: When this option is selected, the driver
will download any fonts as graphics. When printing documents
with high graphic content and relatively few TrueType fonts,
printing performance (speed) may be enhanced in this
setting.
• Print All Text To Black: When the Print All Text To Black
option is checked, all text in your document prints solid black,
regardless of the color it appears on the screen.
You can select output options for your document. See "Printing
a Document" on page 12 for more information about accessing
the printer properties.
Click the Extras tab to access the following feature:
1
2
3
1 Watermark
You can create a background text image to be printed on each page of
your document. For details, see "Using Watermarks" on page 21.
2 Overlay
Overlays are often used to take the place of preprinted forms and
letterhead paper. For details, see "Using Overlays" on page 22.
3 Output Options
• Print Subset: You can set the sequence in which the pages
print. Select the print order from the drop-down list.
- Normal: Your printer prints all pages from the first page to
the last page.
- Reverse All Pages(3,2,1): Your printer prints all pages from
the last page to the first page.
- Print Odd Pages: Your printer prints only the odd numbered
pages of the document.
- Print Even Pages: Your printer prints only the even
numbered pages of the document.
• Use Printer Fonts: When Use Printer Fonts is checked, the
printer uses the fonts that are stored in its memory (resident
fonts) to print your document, rather than downloading the
fonts used in your document. Because downloading fonts takes
time, selecting this option can speed up your printing time.
When using Printer fonts, the printer will try to match the fonts
used in your document to those stored in its memory. If,
however, you use fonts in your document that are very different
from those resident in the printer, your printed output will
appear very different from what it looks like on the screen.
This feature is available only when you use the PCL
printer driver.
16
Basic Printing
Troubleshooting Tab
Using a Favorite Setting
Click the Troubleshooting tab to access the following feature:
The Favorites option, which is visible on each properties tab,
allows you to save the current properties settings for future use.
To save a Favorites item:
1
1
2
Change the settings as needed on each tab.
3
Click Save.
Enter a name for the item in the Favorites input box.
2
3
When you save Favorites, all current driver settings are
saved.
To use a saved setting, select the item from the Favorites drop
down list. The printer is now set to print according to the
Favorites setting you selected.
1 Printer Information Page
To delete a Favorites item, select it from the list and click
Delete.
To print information pages or to perform diagnostic actions,
select an item from the list below and click Print
You can also restore the printer driver’s default settings by
selecting Printer Default from the list.
2 Web Links
If you have an Internet connection and a browser installed,
click one of the web links to connect to a web page directly from
the driver.
Using Help
Your printer has a help screen that can be activated by clicking
the Help button in the printer properties window. These help
screens give detailed information about the printer features
provided by the printer driver.
3 About
Use the About tab to display the copyright notice and the
version number of the driver.
You can also click
from the upper right corner of the window,
and then click on any setting.
Printer Tab
If you access printer properties through the Printers folder, you
can view the Printer tab. You can set the printer configuration.
The following procedure is for Windows XP. For other Windows OS,
refer to the corresponding Windows User's Guide or online help.
1 Click the Windows Start menu.
2
3
4
5
Select Printers and Faxes.
Select your printer driver icon.
Right-click on the printer driver icon and select
Properties.
Click the Printer tab and set the options.
17
Basic Printing
4
Advanced Printing
Printing Multiple Pages on One
Sheet of Paper (N-Up Printing)
This chapter explains printing options and advanced printing
tasks.
1
2
3
4
NOTES:
• Your printer driver Properties window that appears in this
User’s Guide may differ depending on the printer in use.
However the composition of the printer properties window is
similar.
• If you need to know the exact name of your printer, you can
check the supplied CD-ROM.
You can select the number of pages to print on a single sheet
of paper. To print more than one page per sheet, the pages will
be reduced in size and arranged in the order you specify. You
can print up to 16 pages on one sheet.
1
2
This chapter includes:
3
• Printing Multiple Pages on One Sheet of Paper (N-Up
Printing)
4
• Printing Posters
• Printing Booklets
5
• Printing on Both Sides of Paper
• Printing a Reduced or Enlarged Document
6
• Fitting Your Document to a Selected Paper Size
• Using Watermarks
• Using Overlays
18
Advanced Printing
To change the print settings from your software
application, access printer properties. See "Printing a
Document" on page 12.
From the Layout tab, choose Multiple Pages per Side in
the Layout Type drop-down list.
Select the number of pages you want to print per sheet
(1, 2, 4, 6, 9, or 16) in the Pages per Side drop-down list.
Select the page order from the Pages Order drop-down
list, if necessary.
Check Print Page Border to print a border around each
page on the sheet.
Click the Paper tab, select the paper source, size, and
type.
Click OK and print the document.
Printing Posters
Printing Booklets
This feature allows you to print a single-page document onto 4,
9, or 16 sheets of paper, for the purpose of pasting the sheets
together to form one poster-size document.
1
2
3
8
To change the print settings from your software
application, access printer properties. See "Printing a
Document" on page 12.
Click the Layout tab, select Poster Printing in the
Layout Type drop-down list.
Configure the poster option:
9
NOTE: The Booklet Printing option is not available for all
paper sizes. In order to find out the available paper size for
this feature, select the paper size in the Size option on the
Paper tab, then check if the Booklet Printing in a Layout
Type drop-down list on the Layout tab is activated.
3
4
5
Specify an overlap in millimeters or inches to make it
easier to pasting the sheets together.
0.15 inches
0.15 inches
5
8
This printer feature allows you to print your document on both
sides of the paper and arranges the pages so that the paper can
be folded in half after printing to produce a booklet.
1 To change the print settings from your software
application, access the printer properties. See "Printing a
Document" on page 12.
2 From the Layout tab, choose Booklet Printing from the
Type drop-down list.
You can select the page layout from Poster<2x2>,
Poster<3x3>, Poster<4x4> or Custom. If you select
Poster<2x2>, the output will be automatically stretched
to cover 4 physical pages. If the option is set to Custom,
you can enlarge the original from 150% to 400%.
Depending on the level of the enlargement, the page
layout is automatically adjusted to Poster<2x2>,
Poster<3x3>, Poster<4x4>.
4
9
Click the Paper tab, select the paper source, size, and
type.
Click OK and print the document. You can complete the
poster by pasting the sheets together.
19
Advanced Printing
Click the Paper tab, and select the paper source, size, and
type.
Click OK and print the document.
After printing, fold and staple the pages.
Printing on Both Sides of Paper
Printing a Reduced or Enlarged
Document
You can print on both sides of a sheet of paper. Before printing,
decide how you want your document oriented.
You can change the size of a page’s content to appear larger or
smaller on the printed page.
The options are:
• Printer Setting, if you select this option, this feature is
determined by the setting you’ve made on the control
panel of the printer.
• None
• Long Edge, which is the conventional layout used in
book binding.
• Short Edge, which is the type often used with calendars.
1
2
3
4
5
2
2
To change the print settings from your software
application, access printer properties. See "Printing a
Document" on page 12.
From the Paper tab, select Reduce/Enlarge in the
Printing Type drop-down list.
Enter the scaling rate in the Percentage input box.
You can also click the
or
button.
Select the paper source, size, and type in Paper Options.
Click OK and print the document.
3
3
2
5
5
2
3
5
3
5
s Long Edge
Fitting Your Document to a
Selected Paper Size
s Short Edge
• Reverse Duplex, allows you to select general print
order compare to duplex print order.
NOTE:
A
• Do not print on both sides of labels, transparencies,
envelopes, or thick paper. Paper jamming and damage to the
printer may result.
• To use double-sided printing, you can use only the following
paper sizes: A4, Letter, Legal, Oficio and Folio, with a weight
of 20~24 lbs (75~90 g/m²).
1
2
3
4
5
This printer feature allows you to scale your print job to any
selected paper size regardless of the digital document size. This
can be useful when you want to check fine details on a small
document.
1
2
3
To change the print settings from your software
application, access printer properties. "Printing a
Document" on page 12.
From the Layout tab, select the paper orientation.
4
5
From the Double-sided Printing section, select the
binding option you want.
Click the Paper tab and select the paper source, size, and
type.
Click OK and print the document.
20
Advanced Printing
To change the print settings from your software
application, access printer properties. See "Printing a
Document" on page 12.
From the Paper tab, select Fit to Page in the Printing
Type drop-down list.
Select the correct size from the Output size drop-down
list.
Select the paper source, size, and type in Paper Options.
Click OK and print the document.
Editing a Watermark
Using Watermarks
1
The Watermark option allows you to print text over an existing
document. For example, you may want to have large gray
letters reading “DRAFT” or “CONFIDENTIAL” printed diagonally
across the first page or all pages of a document.
2
There are several predefined watermarks that come with the
printer, and they can be modified, or you can add new ones to
the list.
3
4
5
Using an Existing Watermark
1
2
3
To change the print settings from your software
application, access printer properties. See "Printing a
Document" on page 12.
Click the Extras tab, and select the desired watermark
from the Watermark drop-down list. You will see the
selected watermark in the preview image.
Click OK and start printing.
1
2
3
it is printed.
4
Creating a Watermark
2
3
4
5
6
Click OK until you exit the Print window.
Deleting a Watermark
NOTE: The preview image shows how the page will look when
1
To change the print settings from your software
application, access printer properties. See "Printing a
Document" on page 12.
Click the Extras tab and click the Edit button in the
Watermark section. The Edit Watermark window
appears.
Select the watermark you want to edit from the Current
Watermarks list and change the watermark message and
options.
Click Update to save the changes.
To change the print settings from your software
application, access printer properties. See "Printing a
Document" on page 12.
Click the Extras tab, and click the Edit button in the
Watermark section. The Edit Watermark window
appears.
Enter a text message in the Watermark Message box.
You can enter up to 40 characters. The message displays
in the preview window.
When the First Page Only box is checked, the watermark
prints on the first page only.
Select watermark options.
You can select the font name, style, size, or grayscale level
from the Font Attributes section and set the angle of the
watermark from the Message Angle section.
Click Add to add a new watermark to the list.
When you have finished editing, click OK and start
printing.
To stop printing the watermark, select (No Watermark) from
the Watermark drop-down list.
21
Advanced Printing
To change the print settings from your software
application, access printer properties. See "Printing a
Document" on page 12.
From the Extras tab, click the Edit button in the
Watermark section. The Edit Watermark window
appears.
Select the watermark you want to delete from the Current
Watermarks list and click Delete.
Click OK until you exit the Print window.
Using a Page Overlay
Using Overlays
After an overlay has been created, it is ready to be printed with
your document. To print an overlay with a document:
1
2
What is an Overlay?
Dear ABC
Regards
WORLD BEST
An overlay is text and/or images stored in the computer hard
disk drive (HDD) as a special file format that can be printed on
any document. Overlays are often used to take the place of
preprinted forms and letterhead paper. Rather than using
preprinted letterhead, you can create an overlay containing the
exact same information that is currently on your letterhead. To
print a letter with your company’s letterhead, you do not need
to load preprinted letterhead paper in the printer. You need only
tell the printer to print the letterhead overlay on your
document.
3
4
5
To use a page overlay, you must create a new page overlay
containing your logo or image.
WORLD BEST
2
3
4
5
6
7
To change the print settings from your software
application, access printer properties. See "Printing a
Document" on page 12.
Click the Extras tab.
Select the desired overlay from the Overlay drop-down
list box.
If the overlay file you want does not appear in the
Overlay list, click Edit button and Load Overlay, and
select the overlay file.
If you have stored the overlay file you want to use in an
external source, you can also load the file when you access
the Load Overlay window.
Creating a New Page Overlay
1
Create or open the document you want to print.
6
Create or open a document containing text or an image for
use in a new page overlay. Position the items exactly as
you wish them to appear when printed as an overlay.
To save the document as an overlay, access printer
properties. See "Printing a Document" on page 12.
Click the Extras tab, and click Edit button in the Overlay
section.
In the Edit Overlay window, click Create Overlay.
7
After you select the file, click Open. The file appears in the
Overlay List box and is available for printing. Select the
overlay from the Overlay List box.
If necessary, click Confirm Page Overlay When
Printing. If this box is checked, a message window
appears each time you submit a document for printing,
asking you to confirm your wish to print an overlay on your
document.
If this box is not checked and an overlay has been
selected, the overlay automatically prints with your
document.
Click OK or Yes until printing begins.
In the Create Overlay window, type a name of up to eight
characters in the File name box. Select the destination
path, if necessary. (The default is C:\Formover).
Click Save. The name appears on the Overlay List box.
NOTE: The resolution of the overlay document must be the
Click OK or Yes to finish creating.
same as that of the document you will print with the overlay.
The selected overlay downloads with your print job and
prints on your document.
The file is not printed. Instead it is stored on your
computer hard disk drive.
Deleting a Page Overlay
NOTE: The overlay document size must be the same as the
documents you print with the overlay. Do not create an overlay
with a watermark.
You can delete page overlays that you no longer use.
1
2
3
4
5
6
22
Advanced Printing
In the printer properties window, click the Extras tab.
Click the Edit button in the Overlay section.
Select the overlay you want to delete from the Overlay
List box.
Click Delete Overlay.
When a confirming message window appears, click Yes.
Click OK until you exit the Print window.
5
Advanced
Using Windows PostScript
Driver
You can use advanced settings by clicking the Advanced
button.
If you want to use the PostScript driver provided with your
system CD-ROM to print a document.
PPDs, in combination with the PostScript driver, access printer
features and allow the computer to communicate with the
printer. An installation program for the PPDs is provided on the
supplied software CD-ROM.
This chapter includes:
Printer Settings
You can use the printer properties window, which allows you to
access all of the printer options you need when using your
printer. When the printer properties are displayed, you can
review and change the settings needed for your print job.
Your printer properties window may differ, depending on your
operating system. This Software User’s Guide shows the
Properties window for Windows XP.
• Paper/Output this option allows you to select the size of the
paper loaded in tray.
• Graphic this option allows you to adjust the print quality for
your specific printing needs.
• Document Options this options allow you to set the PostScript
options or printer features.
Your printer driver Properties window that appears in this
User’s Guide may differ depending on the printer in use.
NOTES:
• Most Windows applications will override settings you specify
in the printer driver. Change all print settings available in the
software application first, and change any remaining settings
using the printer driver.
• The settings you change remain in effect only while you are
using the current program. To make your changes
permanent, make them in the Printers folder.
• The following procedure is for Windows XP. For other
Windows OS, refer to the corresponding Windows User's
Guide or online help.
1. Click the Windows Start button.
2. Select Printers and Faxes.
3. Select your printer driver icon.
4. Right-click on the printer driver icon and select
Printing Preferences.
5. Change the settings on each tab, click OK.
Using Help
You can click
from the upper right corner of the window, and
then click on any setting.
23
Using Windows PostScript Driver
6
Using Utility Applications
Opening the Troubleshooting
Guide
If an error occurs while printing, the Status Monitor window
appears, showing the error.
Using the troubleshooting guide, you can view solutions for
error status problems.
Double click the Status Monitor icon on the Windows task bar.
Or, from the Start menu, select Programs or All Programs
→ your printer driver name → Troubleshooting Guide.
NOTES:
• To use the this program, you need:
- To check for Operating System(s) that are compatible with
your printer, refer to Printer Specifications in your Printer
User’s Guide.
- Internet Explorer version 5.0 or higher for flash animation
in HTML Help.
• If you need to know the exact name of your printer, you can
check the supplied CD-ROM.
Double click this icon.
Using Printer Settings Utility
Changing the Status Monitor
Program Settings
Using the Printer Settings Utility, you can configure and check
print settings.
Select the Status Monitor icon on the Windows task bar and
right-click on the Status Monitor icon. Select Options.
1
The following window opens.
2
3
from the Start menu, select Programs or All Programs
→ your printer driver name → Printer Settings Utility.
Change the settings.
To send the changes to the printer, click the Apply button.
Using Onscreen Help
For more information about Printer Settings Utility, click
.
• Display when job is finished for network printer shows
the Status Monitor balloon when your job is complete.
(Only for a network supported printer.)
• Display when error occurs during printing shows the
Status Monitor balloon when an error occurs during
printing.
• Schedule an automatic status checking every allows
the computer to update the printer status regularly.
Setting the value close to 1 second causes the computer
to check the printer status more frequently, thereby
allowing a faster response to any printer error.
24
Using Utility Applications
7
Sharing the Printer
Locally
Setting Up a Host Computer
1
2
3
4
5
6
You can connect the printer directly to a selected computer,
which is called “host computer,” on the network.
The following procedure is for Windows XP. For other Windows OS,
refer to the corresponding Windows User's Guide or online help.
Start Windows.
From the Start menu select Printers and Faxes.
Double-click your printer driver icon.
From the Printer menu, select Sharing.
Check the Share this printer box.
Fill in the Shared Name field, and then click OK.
NOTES:
• Check the Operating System(s) that are compatible with
your printer. Please refer to the OS Compatibility section of
Printer Specifications in your Printer User’s Guide.
• If you need to know the exact name of your printer, you can
check the supplied CD-ROM.
Setting Up a Client Computer
1
2
3
4
5
6
25
Sharing the Printer Locally
Right-click the Windows Start button and select Explore.
Select My Network Places and then right-click Search
for Computers.
Fill in the IP address of host computer in Computer name
field, and click Search. (In case host computer requires
User name and Password, fill in User ID and password
of host computer account.)
Double-click Printers and Faxes.
Right-click printer driver icon, select Connect.
Click Yes, if the installation confirm message appears.
8
Using Your Printer in
Linux
Installing the Unified Linux
Driver
You can use your machine in a Linux environment.
Installing the Unified Linux Driver
1
This chapter includes:
• Getting Started
2
• Installing the Unified Linux Driver
Make sure that you connect your machine to your
computer. Turn both the computer and the machine on.
When the Administrator Login window appears, type in
root in the Login field and enter the system password.
• Using the Unified Driver Configurator
NOTE: You must log in as a super user (root) to install the
• Configuring Printer Properties
printer software. If you are not a super user, ask your system
administrator.
• Printing a Document
3
Getting Started
Insert the printer software CD-ROM. The CD-ROM will
automatically run.
If the CD-ROM does not automatically run, click the
icon at the bottom of the desktop. When the Terminal
screen appears, type in:
The supplied CD-ROM provides you with Xerox’s Unified Linux
Driver package for using your machine with a Linux computer.
If the CD-ROM is secondary master and the location to
mount is /mnt/cdrom,
After the driver is installed on your Linux system, the driver
package allows you to monitor a number of machine devices via
fast ECP parallel ports and USB simultaneously.
[root@localhost root]#mount -t iso9660 /dev/hdc /mnt/
cdrom
The Unified Linux Driver package is supplied with a smart and
flexible installation program. You don't need to search for
additional components that might be necessary for the Unified
Linux Driver software: all required packages will be carried onto
your system and installed automatically; this is possible on a
wide set of the most popular Linux clones.
[root@localhost root]#cd /mnt/cdrom/Linux
[root@localhost root]#./install.sh
If you still failed to run the CD-ROM, type the followings
in sequence:
[root@localhost root]#umount/dev/hdc
[root@localhost root]#mount -t iso9660 /dev/hdc /mnt/
cdrom
NOTE: The installation program runs automatically if you
have an autorun software package installed and configured.
4
26
Using Your Printer in Linux
When the welcome screen appears, click Next.
5
Uninstalling the Unified Linux Driver
When the installation is complete, click Finish.
1
When the Administrator Login window appears, type in
root in the Login field and enter the system password.
NOTE: You must log in as a super user (root) to install the
printer software. If you are not a super user, ask your system
administrator.
2
Insert the printer software CD-ROM. The CD-ROM will
automatically run.
If the CD-ROM does not automatically run, click the
icon at the bottom of the desktop. When the Terminal
screen appears, type in:
If the CD-ROM is secondary master and the location to
mount is /mnt/cdrom,
The installation program has added the Unified Driver
Configurator desktop icon and Xerox Unified Driver group
to the system menu for your convenience. If you have
any difficulties, consult the onscreen help that is available
through your system menu or can otherwise be called
from the driver package windows applications, such as
Unified Driver Configurator.
[root@localhost root]#mount -t iso9660 /dev/hdc /mnt/
cdrom
[root@localhost root]#cd /mnt/cdrom/Linux
[root@localhost root]#./uninstall.sh
NOTE: Installing the driver in the text mode:
NOTE: The installation program runs automatically if you
• If you do not use the graphical interface or have failed the
driver installation, you have to use the driver in the text
mode.
• Follow the step 1 to 3, then type [root@localhost Linux]# ./
install.sh, than follow the instruction on the terminal screen.
Then the installation completes.
• When you wan to uninstall the driver, follow the installation
instruction above, but type [root@localhost Linux]# ./
uninstall.sh on the terminal screen.
have an autorun software package installed and configured.
27
Using Your Printer in Linux
3
4
Click Uninstall.
5
Click Finish.
Click Next.
Printers Configuration
Using the Unified Driver
Configurator
Printers configuration has the two tabs: Printers and Classes.
Printers Tab
You can see the current system’s printer configuration by
clicking on the printer icon button on the left side of the Unified
Driver Configurator window.
Unified Linux Driver Configurator is a tool primarily intended for
configuring Printer.
After installing the Unified Linux driver, the Unified Linux Driver
Configurator icon will automatically be created on your desktop.
Switches to Printer
configuration.
Opening the Unified Driver
Configurator
1
2
Shows all of the
installed printer.
Double-click Unified Driver Configurator on the
desktop.
You can also click the Startup Menu icon and select Xerox
Unified Driver and then Unified Driver Configurator.
Press each button on the Modules pane to switch to the
corresponding configuration window.
Shows the status,
model name and
URI of your printer.
Printers Configuration button
You can use the following printer control buttons:
• Refresh: renews the available printers list.
Scanners Configuration button
• Add Printer: allows you to add a new printer.
Ports Configuration button
• Remove Printer: removes the selected printer.
• Set as Default: sets the current printer as a default
printer.
• Stop/Start: stops/starts the printer.
• Test: allows you to print a test page to check if the
machine is working properly.
• Properties: allows you to view and change the printer
properties. For details, see page 29.
3
You can use the onscreen help by clicking Help.
After changing the configurations, click Exit to close the
Unified Driver Configurator.
28
Using Your Printer in Linux
Classes Tab
Configuring Printer Properties
The Classes tab shows a list of available printer classes.
Using the properties window provided by the Printers
configuration, you can change the various properties for your
machine as a printer.
1 Open the Unified Driver Configurator.
Shows all of the
printer classes.
2
3
If necessary, switch to Printers configuration.
Select your machine on the available printers list and click
Properties.
The Printer Properties window opens.
Shows the status of the
class and the number of
printers in the class.
• Refresh : Renews the classes list.
• Add Class... : Allows you to add a new printer class.
• Remove Class : Removes the selected printer class.
Ports Configuration
In this window, you can view the list of available ports, check
the status of each port and release a port that is stalled in busy
state when its owner is terminated for any reason.
Switches to
ports
configuration.
Shows all of the
available ports.
Shows the port type,
device connected to
the port and status
4
• Refresh : Renews the available ports list.
• Release port : Releases the selected port.
29
Using Your Printer in Linux
The following five tabs display at the top of the window:
•General: allows you to change the printer location and
name. The name entered in this tab displays on the
printer list in Printers configuration.
•Connection: allows you to view or select another port. If
you change the printer port from USB to parallel or vice
versa while in use, you must re-configure the printer port
in this tab.
•Driver: allows you to view or select another printer
driver. By clicking Options, you can set the default
device options.
•Jobs: shows the list of print jobs. Click Cancel job to
cancel the selected job and select the Show completed
jobs check box to see previous jobs on the job list.
•Classes: shows the class that your printer is in. Click
Add to Class to add your printer to a specific class or
click Remove from Class to remove the printer from the
selected class.
Click OK to apply the changes and close the Printer
Properties Window.
Printing a Document
Printing from Applications
There are a lot of Linux applications that you are allowed to
print from using Common UNIX Printing System (CUPS). You
can print on your machine from any such application.
1 From the application you are using, select Print from the
File menu.
2 Select Print directly using lpr.
3
5
In the LPR GUI window, select the model name of your
machine from the Printer list and click Properties.
6
7
Click.
The following four tabs display at the top of the window.
•General - allows you to change the paper size, the paper
type, and the orientation of the documents, enables the
duplex feature, adds start and end banners, and changes
the number of pages per sheet.
•Text - allows you to specify the page margins and set the
text options, such as spacing or columns.
•Graphics - allows you to set image options that are used
when printing images/files, such as color options, image
size, or image position.
•Device: allows you to set the print resolution, paper
source, and destination.
Click Apply to apply the changes and close the Properties
window.
Click OK in the LPR GUI window to start printing.
The Printing window appears, allowing you to monitor the
status of your print job.
To abort the current job, click Cancel.
Printing Files
You can print many different types of files on the Xerox machine
device using the standard CUPS way - directly from the
command line interface. The CUPS lpr utility allows you do that.
But the drivers package replaces the standard lpr tool by a
much more user-friendly LPR GUI program.
To print any document file:
1 Type lpr <file_name> from the Linux shell command
line and press Enter. The LPR GUI window appears.
4
Change the printer and print job properties.
2
3
30
Using Your Printer in Linux
When you type only lpr and press Enter, the Select
file(s) to print window appears first. Just select any files
you want to print and click Open.
In the LPR GUI window, select your printer from the list,
and change the printer and print job properties.
For details about the properties window, see page 30.
Click OK to start printing.
9
Using Your Printer with a
Macintosh
Uninstalling the printer driver
1
Your printer supports Macintosh systems with a built-in USB
interface or 10/100 Base-TX network interface card. When you
print a file from a Macintosh computer, you can use the driver by
installing the PPD file.
2
3
4
This chapter includes:
• Installing printer driver for Macintosh
5
6
7
• Setting Up the Printer
• Printing
The PostScript driver CD-ROM that came with your machine
provides you with the PPD file to use the PS driver, Apple
LaserWriter driver, for printing on a Macintosh computer.
2
3
4
5
6
7
Insert the PostScript driver CD-ROM which came with your
machine into the CD-ROM drive.
Double-click CD-ROM icon that appears on your
Macintosh desktop.
Double-click the MAC_Installer folder.
Double-click the MAC_Printer folder.
For Mac OS 10.3 or higher, double-click the Xerox
Phaser 3435_OSX icon.
8 Select Uninstall and then click Uninstall.
9 Click Continue.
10 When the uninstallation is done, click Quit.
Installing printer driver for
Macintosh
1
Connect your machine to the computer using the USB
cable or the Ethernet cable.
Turn on your computer and the machine.
Connect your machine to the computer using the USB
cable or the Ethernet cable.
Turn on your computer and the machine.
Insert the PostScript driver CD-ROM which came with your
machine into the CD-ROM drive.
Double-click CD-ROM icon that appears on your
Macintosh desktop.
Double-click the MAC_Installer folder.
Double-click the MAC_Printer folder.
For Mac OS 10.3 or higher, double-click the Xerox
Phaser 3435_OSX icon.
Enter the password and click OK.
8
9 Click Continue.
10 Select Easy Install and click Install.
11 After the installation is finished, click Quit.
31
Using Your Printer with a Macintosh
For a USB-connected Macintosh
Setting Up the Printer
Mac OS 10.3 or higher
1
Set up for your printer will be different depending on which
cable you use to connect the printer to your computer—the
network cable or the USB cable.
2
For a Network-connected Macintosh
NOTE: Some printers do not support a network interface.
3
Before connecting your printer, make sure that your
printer supports a network interface by referring to Printer
Specifications in your Printer User’s Guide.
Follow the instructions on Installing printer driver for
Macintosh on page 31 to install the PPD file on your
computer.
Open Print Center or Printer Setup Utility from the
Utilities folder.
•For MAC OS 10.5, open System Preferences from the
Applications folder, and click Print & Fax.
Click Add on the Printer List.
•For MAC OS 10.5, press the “+” icon then a display
window will pop up.
4
For MAC OS 10.3, select the USB tab.
Mac OS 10.3 or higher
•For MAC OS 10.4, click Default Browser and find the
USB connection.
1
•For MAC OS 10.5, click Default and find the USB
connection.
2
3
Follow the instructions on Installing printer driver for
Macintosh on page 31 to install the PPD file on your
computer.
Open Print Center or Printer Setup Utility from the
Utilities folder.
5
6
•For MAC OS 10.5, open System Preferences from the
Applications folder, and click Print & Fax.
Click Add on the Printer List.
•For MAC OS 10.5, if Auto Select does not work properly,
select Select a driver to use... and your printer name
in Print Using.
For MAC OS 10.3, select the Rendezvous tab.
•For MAC OS 10.4, click Default Browser and find the
Bonjour.
Your machine appears on the Printer List and is set as the
default printer.
•For MAC OS 10.5, click Default and find the Bonjour.
7
The name of your machine appears on the list. Select
XRX000xxxxxxxxx from the printer box, where the
xxxxxxxxx varies depending on your machine.
5
For MAC OS 10.3, if Auto Select does not work properly,
select Xerox in Printer Model and your printer name in
Model Name.
•For MAC OS 10.4, if Auto Select does not work properly,
select Xerox in Print Using and your printer name in
Model.
•For MAC OS 10.5, if Auto Select does not work properly,
select Select a driver to use... and your printer name
in Print Using.
6
For MAC OS 10.3, if Auto Select does not work properly,
select Xerox in Printer Model and your printer name in
Model Name.
•For MAC OS 10.4, if Auto Select does not work properly,
select Xerox in Print Using and your printer name in
Model.
•For MAC OS 10.5, press the “+” icon then a display
window will pop up.
4
Select your printer name.
Your machine appears on the Printer List and is set as the
default printer.
Click Add.
32
Using Your Printer with a Macintosh
Click Add.
Installable Options
Printing
After setting up for your printer, you can set some more
detailed options.
NOTES:
1
2
3
• The Macintosh printer’s properties window that appears in
this User’s Guide may differ depending on the printer in use.
However the composition of the printer properties window is
similar.
• You can check your printer name in the supplied CD-ROM.
Open Print Center or Printer Setup Utility from the
Utilities folder.
•For MAC OS 10.5, open System Preferences from the
Applications folder, and click Print & Fax.
Select your printer model name.
Click Show Info.
4
•For MAC OS 10.5, click Options & Supplies...
Select Installable Options tab.
5
•For MAC OS 10.5, Select Driver tab.
Configure each items in Installable Options window.
When you print with a Macintosh, you need to check the printer
software setting in each application you use. Follow these steps
to print from a Macintosh.
•Tray n: If the machine have optional tray n, you have to
check the tray name.
1
•Duplex Unit: If the machine has duplex unit, you have t
o check this item.
2
•Printer Memory: If you installed additional printer
memory, you have to configure the size of memory.
Select Apply Change.
3
6
Printing a Document
Open a Macintosh application and select the file you want
to print.
Open the File menu and click Page Setup (Document
Setup in some applications).
Choose your paper size, orientation, scaling, and other
options and click OK.
Make sure that your
printer is selected.
▲ Mac OS 10.4
4
5
6
33
Using Your Printer with a Macintosh
Open the File menu and click Print.
Choose the number of copies you want and indicate which
pages you want to print.
Click Print when you finish setting the options.
Changing Printer Settings
Printer Features
You can use advanced printing features when using your
printer.
This tab provides options for selecting the paper type and
adjusting print quality. Select Printer Features from the dropdown list to access the following features:
From your Macintosh application, select Print from the File
menu. The printer name which appears in the printer properties
window may differ depending on the printer in use. Except for
the name, the composition of the printer properties window is
similar.
NOTES: The setting options may differ depending on printers
▲ Mac OS 10.4
and Macintosh OS version.
•Reverse Duplex Printing: Allows you to select general
print order compare to duplex print order.
Layout
•Fit to Page: This printer feature allows you to scale your
print job to any selected paper size regardless of the
digital document size. This can be useful when you want
to check fine details on a small document.
The Layout tab provides options to adjust how the document
appears on the printed page. You can print multiple pages on
one sheet of paper. Select Layout from the drop-down list to
access the following features. For details, see "Printing Multiple
Pages on One Sheet of Paper" on the next column.
•Paper Type: Set Type to correspond to the paper loaded
in tray from which you want to print. This will let you get
the best quality printout. If you load a different type of
print material, select the corresponding paper type.
•Resolution(Quality): The Resolution options you
can select may vary depending on your printer
model. You can select the printing resolution. The higher
the setting, the sharper the clarity of printed characters
and graphics. The higher setting also may increase the
time it takes to print a document.
•Toner Save Mode: Selecting this option extends the life
of your print cartridge and reduces your cost per page
without a significant reduction in print quality.
▲ Mac OS 10.4
•Pages per Sheet: This feature determines how many
pages printed on one page. For details, seePrinting
Multiple Pages on One Sheet of Paper on page 35.
•Layout Direction: You can select the printing direction
on a page as like the examples on UI.
34
Using Your Printer with a Macintosh
Printing Multiple Pages on One Sheet of
Paper
Duplex Printing
You can print on both sides of the paper. Before printing in the
duplex mode, decide on which edge you will be binding your
finished document. The binding options are:
You can print more than one page on a single sheet of paper.
This feature provides a cost-effective way to print draft pages.
1
2
• Long-Edge Binding: Which is the conventional layout used in
book binding.
From your Macintosh application, select Print from the
File menu.
Select Layout.
• Short-Edge Binding: Which is the type often used with
calendars.
1
2
From your Macintosh application, select Print from the
File menu.
Select the Layout.
▲ Mac OS 10.4
3
4
5
Select the number of pages you want to print on one sheet
of paper on the Pages per Sheet drop-down list.
Select the page order from the Layout Direction option.
▲ Mac OS 10.4
3
To print a border around each page on the sheet, select
the option you want from the Border drop-down list.
Click Print, and the printer prints the selected number of
pages on one side of each page.
4
Select a binding orientation from Two Sided Printing
option.
Click Print and the printer prints on both sides of the
paper.
CAUTION: If you have selected duplex printing and
then try to print multiple copies of a document, the
printer may not print the document in the way you
want. In case of "Collated copy" , if your document has
odd pages, the last page of the first copy and the first
page of the next copy will be printed on the front and
back of one sheet. In case of "Uncollated copy", the
same page will be printed on the front and back of one
sheet. Therefore, if you need multiple copies of a
document and you want those copies on both sides of
the paper, you must print them one at a time, as
separate print jobs.
35
Using Your Printer with a Macintosh
SOFTWARE SECTION
INDEX
A
advanced printing, use 18
B
booklet printing 19
D
Device 30
document, print
Macintosh 33
Windows 12
double-sided printing 20
E
Extras properties, set 16
Macintosh 34
Windows 14
Linux
driver, install 26
printer properties 29
printing 30
M
Macintosh
driver
install 31
printing 33
setting up the printer 32
N
n-up printing
Macintosh 35
Windows 18
F
favorites settings, use 17
G
Graphics 15
Graphics properties, set 15
H
help, use 17, 23
I
install
Linux 26
printer driver
Macintosh 31
Windows 4
L
Layout properties, set
O
orientation, print 30
Windows 14
overlay
create 22
delete 22
print 22
P
Paper properties, set 14
paper size, set 14
print 30
paper source, set 30
Windows 15
paper type, set
Macintosh 34
print 30
poster, print 19
PostScript driver
installing 23
print
36
booklets 19
document 12
double-sided 20
fit to page 20
from Linux 30
from Macintosh 33
from Windows 12
N-up
Macintosh 35
Windows 18
overlay 22
poster 21
PRN 13
scaling 20
watermark 21
Print Features properties
Macintosh 34
printer driver
install
Macintosh 31
printer driver, install
Linux 26
printer properties
Linux 30
printer properties, set
Macintosh 34
Windows 13, 23
printer resolution, set
Macintosh 34
Windows 15
printer software
install
Windows 4, 11
uninstall
Windows 10
S
setting
favorites 17
Print All Text To Black 16
resolution 15
Macintosh 34
Windows 15
toner save mode 15
true-type option 15
software
install
Macintosh 31
Windows 4, 11
reinstall
Windows 10
system requirements
Macintosh 31
uninstall
Macintosh 31
Windows 10
status monitor, use 24
T
toner save, set 15, 34
U
uninstall, software
Linux 27
Macintosh 31
Windows 10
W
watermark
create 21
delete 21
edit 21
print 21
37
Download PDF
Similar pages