Scanned Image - JAY Furniture

Page
TWIN LOFT BED
0822
1
of7
ITEM: DLB-D-C-BB
dult assembly required.For ages six and up.
CONGRATULATIONS
PARTS INFORMATION
You've purchased a fine product. All of our easy - toassemble products are designed and carefully tested
to meet the highest quality standards - Yours. We're
included simple step-by-step instructions to help you
recommend that you follow the steps below.
1' Please read the instructions thoroughly
2' Ldentrfy all parts and hardware, and
3' Gather the tool(s) necessary
NOTE: Do not tighten screws until unit is fully assembled.
Only then tighten all screws.
To protect your
parts during assembly
CARE INSTRUCTIONS
To clean surface use only water on a damp
cloth. Do not use window cleaners or cleaning
abrasives as it will scratch the surface and
could damage the protective. coating.
HARDWARE AND TOOLS DIAGRAM
PARTS LIST
REF
PART
QUANTITY
NAME
A1
Barrel Bolts D6
B1
Barrel Nuts
A
Upper Head Boards
2
c1
Barrel Bolts
3
Short Guard Rail
1
D1
Wood
C
Upright Piece of Short Guard Rail
1
5‘
D
Long Guard Rail
E
J1
Nex Key
G1
F
Slat Rolls
1
G
Low Drawer Chest
1
H
Top Panel
1
I
Side Board
3
J
High Drawer Chest
1
K
Top Board (Right)
1
L
Shelf
2
M
Ladder
1
N
Top Board (Left)
1
0
Down Cross Piece
1
P
Up
need a philips
Screwdriver
(not included)
assembly
_
?
A1
G»
D1
@m
G1
Note: You .will need
a flathend screwdriver
to properly orientate
the barrel nuts during
J1
I!
35
ladder
2
Note: You Win also
DB x
11
Side Rails
32
32
H1
F1
1
65
Screws 04.3 x 40
W°°d Screws [343 X 30
Wood Screws 04.3 x 15
Wooden Dowels 012 x 35
Wooden Dowels 08 x 30
-1
Cross Board
x
18
4
32
8
4
2
2
HOOKS
2
B1
@
E1
C1
9)) mm,“
F1
@m @m
H1
'
0822
ASSEMBLY INSTRUCTIONS
TWIN LOFT BED
ITEM DLB D c BB
Page 2 of 7
ASSEMBLY INSTRUCTIONS
0822
TWIN LOFT BED
ITEM: DLB-D-C-BB
the drawers, put
according the drawer.(please
do not mix the sequence, after
J.L.|.N installation, return all
the drawer ).
Pull out all
,
Page 3 of 7
Page4°f7
ASSEMBLY INSTRUCTIONS
TWIN LOFT BED
0822
/‘
ITEM: DLB-D-C-BB
@ x4PCS
’*
w
'
p’
Right Sideboard
of3
-
drChest
©/
..-
9
J
I
O)
'U
L‘s
\L
.
'i\
C (D
We)
1 2:2?‘2312;
/
IX
x
u M.
ASSEMBLY INSTRUCTIONS
0822
TWIN LOFT BED
ITEM: DLB-D-C-BB
.k»
.4\
W P\
@ x 4 PCS
M
®
K/
0
0
J$J
WV
0
W
F
Page5°f7
0822
ASSEMBLY INSTRUCTIONS
TWIN LOFT BED
ITEM DLB D C BB
Page6 of7
0822
ASSEMBLY INSTRUCTIONS
TWIN LOFT BED
ITEM DLB D
”997°”
c BB
6/29
()x32pcs
\
SAFETY WARNING
We put your child’s safety as a Top Priority. Our bunk beds have been tested by an
independent laboratory and are certified to be in compliance with ASTMF-1427, “Standard
Consumer Safety Specification for Bunk Beds" and US. Government specifications 16
Code of Federal Regulations, parts 1213 and 1513.
the information on the warning attached to the upper bunk end structure and on the
carton. Do not remove this label.
Always use the recommended size mattress or mattress support or both to help prevent the
likelihood of entrapment or falls.
Surface of mattress must be at least five inches (127mm) below the upperedge of guardrails.
Do not allow children less than six years of age to use the upper bunk.
Prohibit more than one person on upper bunk.
Periodically check and ensure that the guardrail, ladder and other components are in their
proper position, free from damage, and that all connectors are tight.
Do not allow horseplay on or under the bed and prohibit jumping on the bed.
Always use the ladder for entering and leaving the upper bunk.
Do not use substitute parts. Contact the manufacturer or dealer for replacement parts.
Use of a night light may provide added safety precaution for a child using upper bunk.
if the bunk bed will be placed next to a wall, the guardrail that runs the full length of the bed
should be placed against the wall to prevent entrapment between the bed and the wall.
(This applies only to bunk beds without two full-length guardrails.)
Always use guardrails or both long sides of the upper bunk.
The use of water or sleep flotation mattress is prohibited.
Keep these instructions for future reference.
1. Follow
2.
95.0155.“
AOS°9°N
—l—L
.
.
12.
13.
14.
STRANGULATION HAZARD
Never attach or hang items to any part of the bunk bed that are not designed for use with the
bed for example, but not limited to hooks, belts, and jump ropes.
SIZE OF MATTRESS AND FOUNDATION
Use only mattress which is 74" — 75" long and 37 1/2"-38 1/2" wide on twin upper bunk
or 52 1/2”-53 1/2" wide on full upper benk. The total thickness of mattress and foundation
(slat kit, bunk board, etc.) combined must not exceed 6".
Note There must be at least 5" from mattress sleeping surface to top edge of guardrail.
:
Download PDF
Similar pages