goliath tub filler factory detail floor mount assembly angle, side and

GOLIATH TUB FILLER FACTORY DETAIL
FLOOR MOUNT ASSEMBLY
ANGLE, SIDE AND FRONT VIEWS WITH DIMENSIONS
NON-SWIVEL SPOUT
360°
SWIVEL
25.00”
32.00”
7-1/4”
4.00”
SIDE VIEW
ANGLE VIEW
Bluewater Manufacturing Corporation
Installation Form 025
Phone # 877-890-8006
Page of 5
FRONT VIEW
Fax # 877-373-0649
Revised 11-14-12
GOLIATH TUB FILLER FACTORY DETAIL
FLOOR MOUNT ASSEMBLY
NON-SWIVEL SPOUT
LOWER
UPPER
2 SET
SCREWS
AERATOR
REMOVEABLE
FACTORY
ASSEMBLED
PERMANENTLY
INTO BASE OF
SPOUT
1
FLOOR RISER
2
BRASS SLEEVE
3
BLACK FLAT WASHER
BLACK FLAT WASHER
SLIP COVER
REPLACEABLE
3/4” ROMAN TUB CARTRIDGE
1/4 TURN
2 SET
SCREWS
O-RING
2 O-RINGS
O-RING
FACTORY
SOLDER JOINT
WATERWAY FOR COPPER PIPE
BOLTS
INTO
FLOOR
Bluewater Manufacturing Corporation
Installation Form 025
Phone # 877-890-8006
Page of 5
Fax # 877-373-0649
Revised 11-14-12
GOLIATH TUB FILLER FACTORY DETAIL
FLOOR MOUNT ASSEMBLY
NON-SWIVEL SPOUT
TOP
SLIP COVER
FITS OVER BRASS
MOUNTING BASE
(2) SET SCREWS
NOTE: SET SCREWS
MUST BE INSTALLED
AFTER SLIP COVER IS
SEATED OVER BRASS
MOUNTING BASE
WASHERS
INSIDE BASE
TUBE WATERWAY
TO SEAL
COPPER PIPE
O-RING
BOTTOM
BRASS
MOUNTING
BASE
GLUE JOINT
3/4” x 14 NPT MALE
FITTING
Bluewater Manufacturing Corporation
Installation Form 025
Phone # 877-890-8006
Page of 5
Fax # 877-373-0649
Revised 11-14-12
GOLIATH TUB FILLER FACTORY DETAIL
1/2” FULL-FLOW WITH DUAL EXIT POTENTIAL
EXPLODED VIEW
THERMOSTATIC VALVE
NON-SWIVEL SPOUT
EXPLODED VIEW
PRINT 1
TEMPERATURE
DIAL CAP
CYLINDER RING
SET SCREW
CYLINDER
ESCUTCHEON
ORIGINAL
16PT. STEM
MODIFIED
16PT. STEM
ASSEMBLED VIEW
ORIGINAL
9/16 x 20
ALLTHREAD
SLEEVE
NEW ADAPTER
BUSHING
ORIGINAL
FACTORY
EUROTHERM
LOCKING NUT
NO HEAT
NEW SOLDER JOINT
ONE-PIECE LOCKING NUT
AND BUSHING
EUROTHERM TSV FULL-FLOW
THERMO VALVE.
PLUMBER TO INSTALL
CHECK VALVES UPSTREAM OF
INLET PORTS.
NO TORCH
Bluewater Manufacturing Corporation
Installation Form 025
MODIFIED
9/16 x 20
ALLTHREAD
SLEEVE
Phone # 877-890-8006
Page of 5
Fax # 877-373-0649
Revised 11-14-12
Warranty
VALVE CARE
Your 1/4 turn ceramic valve will provide you a lifetime of service when cared for properly. The most common valve problem is a result of debris in the
water line, such as sand, silt, solder, metal shavings, lime deposits or other foreign particles. Debris can become lodged between the ceramic discs and
result in improper functioning of the open and close action of the valve. Particles can even cause cracks in the ceramic discs and render the cartridge
useless. For further information, please contact Bluewater Manufacturing Corporation @ 877-890-8006 or fax your request to 877-373-0649
BLUE WATER MANUFACTURING CORPORATION
LIMITED PRODUCT WARRANTY
Product/Finish Warranty: Bluewater Manufacturing Corporation warrants that products are free from manufacturing
defects in materials and workmanship for five (5) years from date of invoice. In addition, our Finish Warranty provides limited
LIFETIME coverage for Chrome & PVD finishes, five (5) years for powder coated finishes & Polished Gold. Living finishes are
warranted for workmanship only. If any material proves to be defective after inspection by our company, it will be repaired or
replaced at our discretion at no charge. However, no claims for labor, shipping costs, or consequential damages will be accepted.
What we will do : We will restore any product whose finish proves to be defective back to its original finish at no
charge during the appropriate warranty period stated above. Proof of purchase must be provided. After the warranty
period, Bluewater Manufacturing Corporation will refinish any of its faucets at the prevailing appropriate charge.
W h a t yo u m u s t d o : The fau c ets must be pro per ly inst alled ac c ord ing to our instr u c t ions and s pe c ifi c a tions and are for residential use only. The faucets cannot be altered in any way. You must maintain and clean the
faucets in accordance with the instructions provided with the product. You must use the faucet(s) for residential use only.
How to obtain service: Send your name, address, and telephone number along with a statement describing the nature of the problem and
your paid sales slip or other proof of purchase to:
BLUE WATER MANUFACTURING CORPORATION
3280 Corporate View
Vista, CA 92081
We will then contact you and take appropriate action. Do not send us any part(s) of your faucet(s) or its various connecting hoses unless we have
contacted you and have sent you an approved RGA form. All transportation charges for returned goods must be paid by the customer.
What is not covered: This warranty does not cover the crystal/glass, or porcelain products of any faucet or the drain assembly or aerator on
other than the Chrome or PVD finishes. This warranty also does not cover damage caused by accident, alterations, misuse, abuse, normal wear
and tear, lime deposits, direct exposure to salty air or corrosive materials, or the color change that takes place with the passage of time, or use in
any manner contrary to Bluewater Manufacturing Corporation’s printed instructions. Cartridge warranties vary. Please call factory for
details. In the case of in-the-wall installations, Bluewater Manufacturing Corporation will assume no liability if there is no access. In
no event will we be liable for labor of any kind, incidental or consequential damages. This warranty is extended in lieu of
all other expressed or implied warranties, whether oral or written. Many installation compounds are harmful to brass and metal
finishes. The use of any lead-based or acidic curing adhesive, silicone, mastic, or plumber’s putty on or near our
finished products will void the finish warranty. Use only sealants which are neutral curing and are not reactive
with metal and brass finishes. Bluewater Manufacturing Corporation reserves the right to change, modify or alter its products
as deemed necessary. This warranty supersedes any other American Faucet & Coatings Corporation warranties, whether oral or written.
Unless otherwise contrary to state law governing the purchase, Bluewater Manufacturing Corporation’s liability will
not exceed the wholesale price for the Bluewater Manufacturing Corporation product considered defective. This
warranty gives you specific legal rights, and you may also have other rights which vary from state to state. Some states
do not allow exclusion of incidental or consequential damages, so the above limitation may not apply to you.
LIFETIME WARRANTY ON 1/4 TURN CERAMIC DISC CARTRIDGE
Should the ceramic disc cartridge in your faucet ever fail, Bluewater Manufacturing Corporation will replace the failed part free of charge
to the original purchaser of the product. Your cost will be a $15.95 handling and mailing charge. Labor not included. When ordering replacements,
denote for widespread or centerset lavatory, Roman Tub, or other. Include age of faucet. (This does not include thermostatic, pressure balance,
kitchen or diverter cartridges.)
NOTICE
Bluewater Manufacturing Corporation products are ICC-ES PMG listed and are tested to ASME A112.18.1/CSA B125.1-2011 and
ASSE 1016, and comply with NSF/ANSI 61-2011a and NSF372 - 2010 for basin faucet, bar faucets, and kitchen faucets as required.
Bluewater Manufacturing Corporation
Installation Form 025
Phone # 877-890-8006
Page of 5
Fax # 877-373-0649
Revised 11-14-12
Download PDF
Similar pages