HCD-XB66K
SERVICE MANUAL
E Model
Photo: XB66K
Dolby noise reduction manufactured under license
from Dolby Laboratories Licensing Corporation.
“DOLBY” and the double-D symbol a are trademarks of Dolby Laboratories Licensing Corporation.
CD
Section
Model Name Using Similar Mechanism
HCD290/G330/XB3
CD Mechanism Type
CDM37LH-5BD29AL
Base Unit Name
BU-5BD29AL
Optical Pick-up Name
Tape deck
Model Name Using Similar Mechanism
Section
Tape Transport Mechanism Type
KSS-213D/Q-NP
HCD-H881
TCM-220WR2
SPECIFICATIONS
Amplifier section
The following measured at AC 120/240 V, 50 Hz
DIN power output (Rated)
140 + 140 watts
(8 ohms at 1 kHz, DIN)
Continuous RMS power output (Reference)
170 + 170 watts
(8 ohms at 1 kHz, 10% THD)
Peak music power output (Reference)
3,000 watts
CD player section
System
Laser
Inputs
PHONO IN (phono jacks):
Wavelength
Frequency response
Signal-to-noise ratio
Dynamic range
CD DIGITAL OUT
(square optical connector jack, rear panel)
Wave length:
600 nm
Output level:
–18 dBm
– Continued on next page –
sensitivity 3 mV, impedance
47 kilohms
MIX MIC (phone jack):
sensitivity 1 mV, impedance
10 kilohms
VIDEO/MD (AUDIO) IN (phono jacks):
sensitivity 250 mV, impedance
47 kilohms
Laser output
Compact disc and digital audio system
Semiconductor laser (λ = 780 nm)
Emission
duration: continuous
Max. 44.6 µW*
*This output is the value measured at
a distance of 200 mm from the
objective lens surface on the Optical
Pick-up Block with 7 mm aperture.
780 - 790 nm
2 Hz - 20 kHz (±0.5 dB)
More than 90 dB
More than 90 dB
Outputs
PHONES (stereo phone jack): accepts headphones of 8 ohms or more
VIDEO/MD (AUDIO) OUT (phono jacks):
voltage 250 mV, impedance 1 kilohms
SPEAKER:
accepts impedance of 8 to 16 ohms.
COMPACT DISC DECK RECEIVER
MICROFILM
Tape player section
Recording system
4-track 2-channel stereo
Frequency response (DOLBY NR OFF)
60 - 13,000 Hz (±3 dB),
using a Sony TYPE I cassette
60 - 14,000 Hz (±3 dB),
using a Sony TYPE II cassette
1.
SERVICING NOTES ............................................... 3
2.
GENERAL ................................................................... 4
3.
DISASSEMBLY ......................................................... 7
4.
TEST MODE .............................................................. 15
87.5 - 108.0 MHz (50 kHz step)
FM wire antenna
75 ohm unbalanced
10.7 MHz
5.
MECHANICAL ADJUSTMENTS ........................ 17
6.
ELECTRICAL ADJUSTMENTS
531 - 1,602 kHz
(with the tuning interval set at 9 kHz)
530 - 1,710 kHz (with the tuning
interval set at 10 kHz)
7.
DIAGRAMS
7-1.
7-2.
7-3.
7-4.
7-5.
7-6.
7-7.
7-8.
7-9.
7-10.
7-11.
7-12.
7-13.
7-14.
7-15.
7-16.
7-17.
7-18.
7-19.
7-20.
7-21.
7-22.
7-23.
7-24.
7-25.
7-26.
7-27.
7-28.
7-29.
7-30.
7-31.
IC Pin Function Description ........................................... 22
Block Diagram – CD Section – ..................................... 27
Block Diagram – Tape Deck Section – ......................... 29
Block Diagram – Main Section (1/2) – ......................... 31
Block Diagram – Main Section (2/2) – ......................... 33
Block Diagram – Display/Key Control/
Power Supply Section – .................................................. 35
Circuit Boards ................................................................. 37
Printed Wiring Board – CD Section (1/2) – .................. 39
Schematic Diagram – CD Section (1/2) – ...................... 41
Printed Wiring Boards – CD Section (2/2) – ................ 43
Schematic Diagram – CD Section (2/2) – ...................... 45
Printed Wiring Boards – Tape Deck Section – .............. 47
Schematic Diagram – Tape Deck Section – ................... 49
Printed Wiring Board – Main Section – ........................ 51
Schematic Diagram – Main Section (1/3) – ................... 53
Schematic Diagram – Main Section (2/3) – ................... 55
Schematic Diagram – Main Section (3/3) – ................... 57
Printed Wiring Board – Power Amp Section – ............. 59
Schematic Diagram – Power Amp Section – ................. 61
Printed Wiring Board – Panel Section (1/3) – ............... 63
Schematic Diagram – Panel Section (1/3) –................... 65
Printed Wiring Boards – Panel Section (2/3) – ............. 67
Schematic Diagram – Panel Section (2/3) –................... 69
Printed Wiring Boards – Panel Section (3/3) – ............. 71
Schematic Diagram – Panel Section (3/3) –................... 73
Printed Wiring Board – Power Supply Section – ........... 75
Schematic Diagram – Power Supply Section – .............. 76
Schematic Diagram – Key-Con Section – ...................... 77
Printed Wiriing Board – Key-Con Section – .................. 77
Waveforms ....................................................................... 79
IC Block Diagrams ......................................................... 80
8.
EXPLODED VIEWS ................................................ 83
9.
ELECTRICAL PARTS LIST ............................... 92
Tuner section
FM stereo, FM/AM superheterodyne tuner
FM tuner section
Tuning range
Antenna
Antenna terminals
Intermediate frequency
AM tuner section
Tuning range
(2 band model)
(3 band model )
MW:
LW:
Antenna
Intermediate frequency
TABLE OF CONTENTS
531 -1,602 kHz (with the tuning
interval set at 9 kHz)
153 - 279 kHz (with the tuning
interval set at 3 kHz)
AM loop antenna, External antenna
terminals
450 kHz
General
Power requirements
Mexican model:
120 V AC, 50/60 Hz
Australian and South African models:
220 - 240 V AC, 50/60 Hz
Other models:
110 -120 V or 220 -240 V AC,
50/60 Hz Adjustable with voltage
selector
Power consumption
320 watts
Dimensions (w/h/d)
Approx. 355 × 425 × 435 mm (14 ×
163/ 4 × 17 1/ 4 in) incl. projecting parts
and controls
Mass
Approx. 14.5 kg (31 lb 16 oz.)
Supplied accessories
AM loop antenna (1)
Remote RM-SD70S (1)
Size AA (R6) batteries (2)
FM wire antenna (1)
Speaker cords (2)
Design and specifications are subject to change without notice.
TAPE DECK Section ...................................................... 17
CD Section ...................................................................... 20
–2–
SECTION 1
SERVICING NOTES
NOTES ON HANDLING THE OPTICAL PICK-UP
BLOCK OR BASE UNIT
CAUTION
Use of controls or adjustments or performance of procedures
other than those specified herein may result in hazardous radiation exposure.
This appliance is classified as a CLASS 1 LASER product.
The CLASS 1 LASER PRODUCT MARKING is located on
the rear exterior.
The laser diode in the optical pick-up block may suffer electrostatic break-down because of the potential difference generated
by the charged electrostatic load, etc. on clothing and the human
body.
During repair, pay attention to electrostatic break-down and also
use the procedure in the printed matter which is included in the
repair parts.
The flexible board is easily damaged and should be handled with
care.
NOTES ON LASER DIODE EMISSION CHECK
Laser component in this product is capable of emitting radiation
exceeding the limit for Class 1.
The following caution label is located inside the unit.
CAUTION
:
INVISIBLE LASER RADIATION WHEN
INTERLOCKS DEFEATED. AVOID EXPOSURE TO BEAM.
OPEN
AND
ADVARSEL :
USYNLIG LASERSTRÅLING VED ÅBNING NÅR
SIKKERHEDSAFBRYDERE ER UDE AF FUNKTION. UNDGÅ UDSAETTELSE
FOR STRÅLING.
LASER DIODE AND FOCUS SEARCH OPERATION
CHECK
Carry out the “S curve check” in “CD section adjustment” and
check that the S curve waveforms is output three times.
VORSICHT :
UNSICHTBARE LASERSTRAHLUNG, WENN
ABDECKUNG GEÖFFNET UND SICHEREITSVERRIEGELUNG
ÜBERBRÜCKT. NICHT DEM STRAHL AUSSETZEN.
VARO !
: AVATTAESSA JA SUOJALUKITUS OHITETTAESSA OLET ALTTIINA NÄKYMÄTTÖMÄLLE LASERSÄTEILYLLE. ÄLÄ KATSO SÄTEESEEN.
Notes on chip component replacement
• Never reuse a disconnected chip component.
• Notice that the minus side of a tantalum capacitor may be damaged by heat.
VARNING
: OSYNLING LASERSTRÅLING NÄR DENNA DEL ÄR ÖPPNAD
OCH SPÄRREN ÄR URKOPPLAD. BETRAKTA EJ STRÅLEN.
ADVERSEL :
USYNLIG LASERSTRÅLING NÅR DEKSEL ÅPNES OG
SIKKERHEDSLÅS BRYTES. UNNGÅ EKSPONERING FOR STRÅLEN.
VIGYAZAT ! : A BURKOLAT NYITÁSAKOR LÁTHATATLAN LÉZERSUGÁRVESZÉLY! KERÜLJE A BESUGÁRZÁST!
Flexible Circuit Board Repairing
• Keep the temperature of the soldering iron around 270 ˚C during repairing.
• Do not touch the soldering iron on the same conductor of the
circuit board (within 3 times).
• Be careful not to apply force on the conductor when soldering
or unsoldering.
MODEL IDENTIFICATION
– BACK PANEL –
The laser beam on this model is concentrated so as to be focused
on the disc reflective surface by the objective lens in the optical
pick-up block. Therefore, when checking the laser diode emission, observe from more than 30 cm away from the objective lens.
PART No.
SAFETY-RELATED COMPONENT WARNING!!
MODEL
PART No.
Singapore, Malaysia model
4-996-413-1π
E, Indonesian model
4-996-413-6π
Saudi Arabia model
4-996-413-7π
Thai model
4-996-413-9π
COMPONENTS IDENTIFIED BY MARK ! OR DOTTED
LINE WITH MARK ! ON THE SCHEMATIC DIAGRAMS
AND IN THE PARTS LIST ARE CRITICAL TO SAFE
OPERATION. REPLACE THESE COMPONENTS WITH
SONY PARTS WHOSE PART NUMBERS APPEAR AS
SHOWN IN THIS MANUAL OR IN SUPPLEMENTS PUBLISHED BY SONY.
–3–
SECTION 2
GENERAL
This section is extracted
from instruction manual.
LOCATION OF CONTROLS
– Front Panel –
1
2 3
4
56
7
!§
8
!¶
9
0
!•
!ª
!¡
@º
!™
!£
!¢
@¡
!∞
@™
@§ @¶ @•
@£
@¢
@ª
@∞
#º
#¡
#™
#ª
#£
$º
#¢
$¡
#∞
$™
#§
#¶
$£
#•
$¢ $∞ %º %¡ $§
$¶
$•
$ª
1
2
3
4
5
6
7
8
9
!º
!¡
!™
!£
!¢
!∞
!§
!¶
!•
!ª
@º
@¡
@™
@£
@¢
@∞
I /u (Power) button
DISPLAY/DEMO button
FILE (1-5) indicator
Fluorescent indicator tube
TUNER MEMORY button
TUNING MODE button
TUNER/BAND button and indicator
STEREO/MONO button
FUNCTION button
SUPER WOOFER button and indicator
H SPEED DUB button
CD SYNC button
§ EJECT button (DECK B)
) button (CD)
≠ AMS ± jog dial
t/CLOCK SET button
REC button
PHONES jack
GEQ (4/(/$/9) switch
§ EJECT button (DECK A)
DIRECT PLAY (DISC 1 to DISC 5) button
Cassette holder
CD lid
EFFECT button and indicator
0 button (CD)
@§
@¶
@•
@ª
#º
#¡
#™
#£
#¢
#∞
#§
#¶
#•
#ª
$º
$¡
$™
$£
$¢
$∞
$§
$¶
$•
$ª
%º
%¡
DAILY 1 button
DAILY 2 button
SPECTRUM ANALYZER button
MUSIC/OTHERS/P FILE indicator
ENTER/NEXT button and indicator
TUNING (–) button
TUNING (+) button
GROOVE button and indicator
VOLUME control knob
SUPER W MODE button
6 OPEN button (CD)
· button and indicator (CD)
REPEAT button
SLEEP button
MIC1/MIC2 jack
MIC/ECHO LEVEL control knob
KARAOKE PON/MPX button
NON-STOP button and indicator
LOOP button
FLASH button
ENTER button and indicator
EDIT button
1/ALL DISCS button
PLAY MODE button
KEY CONTROL (˜)
KEY CONTROL (n)
–4–
%º %¡
%™ %£
%¢ %∞
%§
^™
%¶
^£
^¢
%•
^∞
%ª
^§
^º
^¡
^¶ ^•
%º
%¡
%™
%£
%¢
%∞
%§
%¶
%•
%ª
^º
^¡
^™
^£
^¢
^∞
^§
^¶
^•
^ª
&º
WAVE button
SURROUND button
P FILE MEMORY button
GEQ CONTROL button
P button and indicator (DECK B)
p button (DECK B)
ª button and indicator (DECK B)
0 button (DECK B)
· button and indicator (DECK B)
) button (DECK B)
r REC button and indicator (DECK B)
p button (CD)
· button and indicator (DECK A)
0 button (DECK A)
ª button and indicator (DECK A)
p button (DECK A)
DIRECTION button
DOLBY NR button
) button (DECK A)
DISC SKIP button
P button and indicator (CD)
1
2
3
4
5
6
7
8
CD DIGITAL OUT OPTICAL
FM ANTENNA terminal
AM ANTENNA terminal
PHONO IN jack
VIDEO/MD (AUDIO) IN jack
VIDEO/MD (AUDIO) OUT jack
SPEAKER output terminal
VOLTAGE SELECTOR switch
^ª &º
– Rear Panel –
1
2
3
4
5
6
7
8
–5–
–6–
SECTION 3
DISASSEMBLY
• This set can be disassembled in the order shown below.
CASE
(Page 7)
FRONT PANEL
SECTION
(Page 8)
MAIN
SECTION
(Page 9)
CD MECHANISM
DECK SECTION
(Page 9)
BASE UNIT
(Page 12)
BD BOARD
(Page 13)
SLED
MOTOR
(Page 13)
DISC TABLE
(Page 12)
TAPE MECHANISM
DECK SECTION
(Page 10)
AUDIO BOARD
(Page 14)
CAPSTAN MOTOR (M1)
(Page 14)
CASSETTE
LID ASS’Y
(Page 10)
CD LID ASS’Y
SECTION
(Page 11)
PANEL (A)/(B)
SUB ASS’Y
(Page 11)
MAIN/KEY-CON BOARD
(Page 8)
Note: Follow the disassembly procedure in the numerical order given.
3-1. CASE
3 Case
1 Three screws
(case 3 TP2)
1 Three screws
(case 3 TP2)
2 Seven screws
(BATT3 × 6)
–7–
OPTICAL
PICK-UP
(Page 13)
3-2. FRONT PANEL SECTION
1 Wire (flat type) (21 core)
(CN205)
2 Wire (flat type) (11 core)
(CN206)
3 Wire (flat type) (17 core)
(CN102)
5 Front panel section
4 Four screws
(BVTP3 × 8)
3-3. MAIN/KEY-CON BOARD
7 Back panel
5 Eleven screws
(BVTP3 × 8)
6 Power cord
1 Wire (flat type)
(13 core) (CN201)
2 Wire (flat type)
(19 core) (CN202)
!™ KEY-CON board
4 Connector
(CN901)
8 Connector
(CN105)
(Remove soldering)
!¡ MAIN board
IC201
!º Connector
(CN101)
3 Connector
(CN203)
–8–
9 Two screws
(BVTP3 × 8)
3-4. MAIN SECTION
1 Flat wire (CN202)
2 Connector
(CN203)
4 Main section
3 Two screws
(BVTP3 × 8)
3 Screw
(BVTP3 × 8)
3 Two screws
(BVTP3 × 8)
3-5. CD MECHANISM DECK SECTION (CDM37LH-5BD29AL)
3 Five screws
(BVTP3 × 8)
4 CD mechanism
deck section
(CDM37LH-5BD29AL)
2 Flat wire
and lead wire
1 Open the clamp.
–9–
3-6. TAPE MECHANISM DECK SECTION (TCM-220WR2)
5 Three screws
(BVTP2.6 × 8)
5 Three screws
(BVTP2.6 × 8)
4 Wire (flat type)
(21 core) (CN601)
3 Wire (flat type)
(11 core) (CN1001)
6 Remove the tape mechanism deck section
(TCM-220WR2) to direction of the arrow A.
A
2 Open the
cassette lids.
1 Push the
two buttons.
3-7. CASSETTE LID ASS’Y
3 Two bracket
2 Two screws
(BVTP2.6 × 8)
1 Two springs
– 10 –
3-8. CD LID ASS’Y SECTION
6 Four screws
(BVTP2.6 × 8)
5 Connector
(CN671)
7 CD lid ass’y
4 Connector
(CN661)
2 Four screws
(BVTP2.6 × 8)
3 CD-B1 SW board
1 Connector
(CN642)
3-9. PANEL (A) / (B) SUB ASS’Y
1 Connector
(CN612)
3 Two claws
2 Four screws
(BVTP2.6 × 8)
4 Panel (A) sub assy
5 Two claws
6 Panel (B) sub assy
– 11 –
3-10. BASE UNIT
3 Base unit
1 Yoke bracket
2 Boss
3-11. DISC TABLE
Note:
When the disc table is installed, adjust the positions
of roller cam and mark ( as shown in the figure,
then set to the groove of disc table.
A
3 Step screw
1 Screw
(BVTP3 × 8)
2 Bracket (BU)
1 Screw
(BVTP3 × 8)
4 Disc table
A
– 12 –
3-12. BD BOARD
1 Two screws
(PTPWH M2.6 × 8)
1 Two screws
(PTPWH M2.6 × 8)
2 Optical pick-up
section
3 Two springs
3 Two springs
5 Screw
(BVTP2.6 × 8)
4 Wire (flat type)
(16 core) (CN101)
7 BD board
6 Removal
the four solders.
Limit switch
(S101)
3-13. OPTICAL PICK-UP (KSS-213D / Q-NP) , SLED MOTOR (M102) , SPINDLE MOTOR (M101)
3 Optical pick-up (KSS-213D/Q-NP)
6 Spindle motor
(M101)
4 Two screws
(P2 × 3)
2 Sled shaft
5 Sled motor
(M102)
1 Claw
– 13 –
3-14. AUDIO BOARD, CAPSTAN MOTOR (M1)
1 Connector
(CN651)
2 Four screws
(BTP2.6 × 4)
A
3 Removal the AUDIO board
to direction of the arrow A.
5 Two screws
(BTP2.6 × 8)
7 Removal the capstan motor (M1)
to direction of the arrow B.
4 Break the soldering
of motor lead.
B
6 Claw
8 Hang two belts.
– 14 –
SECTION 4
TEST MODE
[MC Cold Reset]
• The cold reset clears all data including preset data stored in the
RAM to initial conditions. Execute this mode when returning
the set to the customer.
Procedure:
1. Press three buttons SPECTRUM ANALYZER , ENTER ,
and
DISC 1 simultaneously.
2. The fluorescent indicator tube becomes blank instantaneously,
and the set is reset.
[CD Delivery Mode]
• This mode moves the pickup to the position durable to vibration. Use this mode when returning the set to the customer after
repair.
Procedure:
1. Press I /u button to turn the set ON.
2. Press PLAY MODE button and I /u button simultaneously.
3. A message “LOCK” is displayed on the fluorescent indicator
tube, and the CD delivery mode is set.
[MC Hot Reset]
• This mode resets the set with the preset data kept stored in the
memory. The hot reset mode functions same as if the power
cord is plugged in and out.
Procedure:
1. Press three buttons SPECTRUM ANALYZER , ENTER ,
and DISC 2 simultaneously.
2. The fluorescent indicator tube becomes blank instantaneously,
and the set is reset.
[Sled Servo Mode]
• This mode can run the CD sled motor freely. Use this mode, for
instance, when cleaning the pickup.
Procedure:
1. Select the function “CD”.
2. Press three buttons SPECTRUM ANALYZER , ENTER ,
and FUNCTION simultaneously.
3. The Sled Servo mode is selected, if “CD” is blanking on the
fluorescent indicator tube.
4. With the CD in stop status, press ) button in CD section
to move the pickup to outside track, or 0 button to inside
track.
5. To exit from this mode, perform as follows:
1) Move the pickup to the most inside track.
2) Press three buttons in the same manner as step 2.
[Change-over of AM Tuner Step between 9kHz and 10kHz]
• A step of AM channels can be changed over between 9kHz and
10kHz.
Procedure:
1. Press I /u button to turn the set ON.
2. Select the function “TUNER”, and press TUNER/BAND
button to select the BAND “AM”.
3. Press I /u button to turn the set OFF.
4. Press ENTER and I /u buttons simultaneously, and the
display of fluorescent indicator tube changes to “AM 9k STEP”
or “AM 10k STEP”, and thus the channel step is changed over.
[LED and Fluorescent Indicator Tube All Lit, Key Check
Mode]
Procedure:
1. Press three buttons SPECTRUM ANALYZER , ENTER ,
and DISC 3 simultaneously.
2. LEDs and fluorescent indicator tube are all turned on.
Press DISC 2 button, and the key check mode is activated.
3. In the key check mode, the fluorescent indicator tube displays
“K 1 J0 V0”. Each time a button is pressed, “K”value increases. However, once a button is pressed, it is no longer taken
into account.
“J” Value increases like 1, 2, 3 ... if rotating ≠ AMS ±
knob in “+” direction, or it decreases like 0, 9, 8 ... if rotating
in “–” direction.
“V” Value increases like 1, 2, 3 ... if rotating VOLUME knob
in “+” direction, or it decreases like 0, 9, 8 ... if rotating in
“–” direction.
4. To exit from this mode, press three buttons in the same manner as step 1, or disconnect the power cord.
Note:
• Always move the pickup to most inside track when exiting from this
mode. Otherwise, a disc will not be unloaded.
• Do not run the sled motor excessively, otherwise the gear can be chipped.
– 15 –
[Aging Mode]
This mode can be used for operation check of CD section and tape
deck section.
• If an error occurred:
The aging operation stops.
• If no error occurs:
The aging operation continues repeatedly.
1. Aging Mode in CD Section
1-1. Operating Method of Aging Mode
1. Set discs in DISC 1 and DISC 3 trays.
2. Select the function “CD”.
3. Press three buttons SPECTRUM ANALYZER , ENTER
, and KARAOKE PON/MPX simultaneously.
4. The aging mode is activated, if a roulette mark on the fluorescent indicator tube is blinking.
5. In the aging mode, the aging is executed in a sequence
given in “1-2. Operation during Aging Mode”.
The aging continues unless an alarm occurred.
6. To exit from the aging mode, press I /u button to turn
the set OFF.
• If a button other than buttons In CD section is pressed during
aging, the aging in the CD section is finished.
• To execute aging to the tape deck section successively, press
· button in the deck A.
“AGING” is displayed on the fluorescent indicator tube. (For
the aging in tape deck, see “2. Aging Mode in Tape Deck Section”.
2-2. Operation during Aging Mode
In the aging mode, the program is executed in the following sequence.
1. A tape on FWD side is played for one minute.
2. PAUSE STOP is made.
3. Recording is made for 3 minutes. (For the deck not having
the record function, the play is executed.)
4. FF is executed up to the end of tape.
5. A tape is reversed, and the tape on REV side is played for
one minute.
6. PAUSE STOP is made.
7. Recording is made for 3 minutes. (For the deck not having the record function, the play is executed.)
8. FF is executed up to the end of tape.
9. Steps 1 through 8 are executed for the other deck.
10. Steps 1 through 9 are repeated unless an alarm occurred.
2-3. Deck Selection Sequence
• During the aging mode, decks are selected in the following sequence:
Deck A (FWD) → Deck A (REV)
↑
↓
Deck B (REV) ← Deck B (FWD)
1-2. Operation during aging Mode
In the aging mode, the program is executed in the following sequence.
1. The disc tray turns to select a disc. (For a disc selection sequence, see Section 1-3.)
2. TOC of disc is read.
3. The pickup accesses to the last track.
4. Steps 1 through 3 are repeated.
1-3. Disc Selection Sequence
• During the aging mode, discs are selected in the following sequence:
Disc 1 → Disc 3
↑
↓
Disc 3 ← Disc 1
2. Aging Mode in Tape Deck Section
2-1. Operating Method of Aging Mode
1. Load a commercially available 10-minute tape into the
decks A and B respectively.
(If a 10-minute tape is not available, another tape may be
used but a cycle time will be longer.)
2. Select the function “TAPE”.
3. Rewind tapes in advance by pressing 0 button respectively on decks A and B.
4. Press three buttons SPECTRUM ANALYZER ,
ENTER , and KARAOKE PON/MPX simultaneously.
5. Press · button on deck A. (This button triggers the aging mode.)
6. The aging mode is activated if “AGING A” is displayed on
the fluorescent indicator tube.
7. In the aging mode, the aging is executed in a sequence
given in “2-2. Operation during Aging Mode”.
The aging continues unless an alarm occurred.
8. To exit from the aging mode, press I /u button to turn
the set OFF.
– 16 –
SECTION 5
MECHANICAL ADJUSTMENTS
SECTION 6
ELECTRICAL ADJUSTMENTS
PRECAUTION
1. Clean the following parts with a denatured-alcohol-moistened
swab:
record/playback heads
pinch rollers
erase head
rubber belts
capstan
idlers
2. Demagnetize the record/playback head with a head demagnetizer.
3. Do not use a magnetized screwdriver for the adjustments.
4. After the adjustments, apply suitable locking compound to the
parts adjusted.
5. The adjustments should be performed with the rated power
supply voltage unless otherwise noted.
• Torque Measurement
• Tape Tension Measurement
• Torque Measurement
Mode
Forward
Torque Meter
CQ-102C
Meter Reading
36 to 61g•cm
(0.50 – 0.84 oz•inch)
Forward
CQ-102C
Back Tension
Reverse
Reverse
CQ-102RC
Back Tension
FF, REW
CQ-201B
1. Demagnetize the record/playback head with a head demagnetizer. (Do not bring the head demagnetizer close to the erase
head.)
2. Do not use a magnetized screwdriver for the adjustments.
3. After the adjustments, apply suitable locking compound to the
parts adjust.
4. The adjustments should be performed with the rated power
supply voltage unless otherwise noted.
5. The adjustments should be performed in the order given in
this service manual. (As a general rule, playback circuit adjustment should be completed before performing recording
circuit adjustment.)
6. The adjustments should be performed for both L-CH and Rch.
7. Switches and controls should be set as follows unless otherwise specified.
8. Set to test mode. (Press key switch same time
SPECTRUM ANALYZER , ENTER and EFFECT button.)
• Test Tape
36 to 61g•cm
(0.50 – 0.84 oz•inch)
Tape
P-4-A100
Used for
Azimuth Adjustment
2 to 6g•cm
WS-48B
3 kHz, 0 dB
Tape Speed Adjustment
P-4-L300
315 Hz, 0 dB
Level Adjustment
61 to 143g•cm
Record/ Playback Head Azimuth Adjustment
DECK A
• Tape Tension Measurement
Forward
Reverse
Signal
10 kHz, –10 dB
(0.026 – 0.082 oz•inch)
(0.85 – 1.98 oz•inch)
Mode
0 dB=0.775 V
2 to 6g•cm
(0.026 – 0.082 oz•inch)
CQ-102RC
TAPE DECK SECTION
Tension Meter
Meter Reading
CQ-403A
CQ-403R
more than 100 g (3.52 oz)
more than 100 g (3.52 oz)
DECK B
Note: Perform this adjustments for both decks
Procedure:
test tape
P-4-A100
(10 kHz, –10 dB)
main board
CN207
Pin 3 (L-CH)
Pin 1 (R-CH) level meter
set
+
–
main board
CN207
Pin 2
– 17 –
1. Mode: Playback (FWD)
2. Turn the adjustment screw and check output peaks. If the peaks
do not match for L-CH and R-CH, turn the adjustment screw
so that outputs match within 1dB of peak.
within
1dB
output
level
Screw
position
test tape
WS-48B
(3 kHz, 0 dB)
R-CH
peak
L-CH
peak
Screw
position
R-CH
peak
frequency counter
+
–
set
MAIN board
CN207 (Pin 3 : L-CH)
(Pin 1 :R-CH)
3. Mode: Playback (FWD)
test tape
P-4-A100
(10 kHz, –10 dB)
L-CH
main
board
CN207
set
1. Insert the WS-48B into the deck A and the blank tape into the
deck B.
2. Press the REC button and · button on the deck B. Then
the deck B is at recording mode.
3. Set the deck A to playback mode.
4. Keep pressing the H. SPEED DUBB button in playback mode.
Then at HIGH speed mode.
5. Adjust RV652 on the AUDIO board do that frequency counter
reads 6,000 ± 180 Hz.
6. Take off the H. SPEED DUBB button.
Then at NORMAL speed mode.
7. Adjust RV651 on the AUDIO board so that frequency counter
reads 3,000 ± 90 Hz.
8. Frequency difference between deck A and deck B the beginning of the tape should be within ± 1.5%.
Adjustment Location: AUDIO and MAIN boards
oscilloscope
pin 3
pin 2
L
V
H
R
R-CH
pin 1
waveform of oscilloscope
in phase 45 ° 90 ° 135 ° 180 °
good
wrong
4. Repeat steps 1 to 3 in playback (REV) mode.
5. After the adjustments, apply suitable locking compound to the
pats adjusted.
Adjustment Location: Record/Playback Head (Deck A and B)
and MAIN board.
Sample Value of Wow and flutter: 0.3% or less W. RMS
(WS-48B)
Playback level Adjustment
Procedure:
Mode: Playback (FWD)
test tape
P-4-L300
(315 Hz, 0 dB)
reverse
DECK A
DECK B
level meter
set
forward
DECK A
Note: Start the Tape Speed adjustment as below after setting to the test
mode.
In the test mode, the tape speed is high during pressing the
H. SPEED DUBB button.
Procedure:
1. Turn the power switch on.
2. Press the SPECTRUM ANALYZER button, ENTER button
and EFFECT button simultaneously.
To exit from the test mode, press the I /u button.
Mode: Playback (FWD)
within
1dB
L-CH
peak
Tape Speed Adjustment
+
–
main board
CN207 (Pin 3 : L-CH)
(Pin 1 : R-CH)
Deck A is RV311 (L-CH) and RV411 (R-CH), Deck B is RV301
(L-CH) and RV401 (R-CH) so that adjustment within adjustment
level as follows.
Adjustment Level:
CN207 PB level: 301.5 to 338.3 mV (–8.2 to –7.2 dB) level
difference between the channels: within ± 0.5 dB
Adjustment Location: AUDIO and MAIN boards
– 18 –
DECK B
Record bias Current Adjustment
Procedure:
1. Mode: Record
Adjustment Location:
[MAIN BOARD] (Component Side)
Pin 6 (L-CH) of IC1501 on the MAIN board.
Pin #¶ (R-CH) of IC1501 on the MAIN board.
1) 315 Hz 
2) 10 kHz  50 mV (–23.8 dB)

AF OSC
blank tape
CN-123
600 Ω
attenuator
RV1501
CN207
1 3 IC1501
CN205
RV1551
RECORD
LEVEL
set
Pin 2 (GND) of CN207 on the MAIN
board.
2. Mode: Playback
recorded
portion
level meter
+
–
set
[AUDIO BOARD] (Conductor Side)



RECORD
BIAS CURRENT
R L
Confirm playback the signal recorded in step 1 become adjustable
limits as follows.
If these levels do not adjustable limits, adjustment the RV341 (LCH) and RV441 (R-CH) on the AUDIO board to repeat steps 1
and 2.
Adjustable limits: Playback output of 315 Hz to playback output
of 10 kHz: 0 ± 0.5 dB
Adjustment Location: AUDIO and MAIN boards
Record Level Adjustment
Procedure:
1. Mode: Record
DECK B
RV301
RV341

L
 RV441

 PB LEVEL
R
RV401 
– DECK B –
blank tape
CS-123
600 Ω
attenuator
set
Pin 2 (GND) of CN207 on the MAIN board.
2. Mode: Playback
recorded
portion
level meter
set
(NORMAL) (HIGH)
RV651 RV652
 RV311 L
PB

LEVEL  RV411 R
– DECK A –
* As the adjustment parts is mounted on the component side, adjust it through a hole in the AUDIO board form conductor side.
(Except RV431, 441)
Pin 6 (L-CH) of IC1501 on the MAIN board.
Pin #¶ (R-CH) of IC1501 on the MAIN board.
315 Hz, 50 mV (–23.8 dB)
AF OSC
TAPE SPEED









CN207 (Pin 3 : L-CH)
(Pin 1 : R-CH)
+
–
CN207 (Pin 3 : L-CH)
(Pin 1 : R-CH)
Confirm playback the signal recorded in step 1 become adjustable
limits as follows.
If these levels do not adjustable limits, adjustment the RV1501
(L-CH) and RV1551 (R-CH) on the MAIN board to repeat steps 1
and 2.
Adjustable limits:
CN207 PB level: 36.7 to 41.1 mV (–26.5 to –25.5 dB)
Adjustment Location: MAIN board
– 19 –
S Curve Check
CD SECTION
oscilloscope
Note:
1. CD Block is basically designed to operate without adjustment. Therefore, check each item in order given.
2. Use YEDS-18 disc (3-702-101-01) unless otherwise indicated.
3. Use an oscilloscope with more than 10M impedance.
4. Clean the object lens by an applicator with neutral detergent when the
signal level is low than specified value with the following checks.
Focus Bias check
oscilloscope
BD board
TP (FEO)
TP (VC)
+
–
Procedure:
1. Connect oscilloscope to test point TP (RF). (GND terminal:
VC)
2. Turned Power switch on.
3. Put disc (YEDS-18) in and playback.
4. Confirm that the shape “≈” can be clearly distinguished at the
center of the waveform and check the RF signal level.
BD board
TP (FEO)
TP (VC)
+
–
Procedure:
1. Connect oscilloscope to test point TP (FEO).
2. Connect between test point TP (FOK) and GND by lead wire.
3. Turn Power switch on.
4. Put disc (YEDS-18) in and turned Power switch on again and
actuate the focus search. (actuate the focus search when disc
table is moving in and out.)
5. Check the oscilloscope waveform (S-curve) is symmetrical
between A and B. And confirm peak to peak level within
3 ± 1 Vp-p.
S-curve waveform
symmetry
A
within 3 ± 1 Vp-p
B
• RF signal
VOLT/DIV: 200 mV
TIME/DIV: 500 ns
level:
1.3 ± 0.3 Vp-p
6. After check, remove the lead wire connected in step 2.
Note: • Try to measure several times to make sure than the ratio of A : B
or B : A is more than 10 : 7.
• Take sweep time as long as possible and light up the brightness to
obtain best waveform.
RF Level Check
oscilloscope
BD board
TP (RF)
TP (VC)
+
–
Procedure:
1. Connect oscilloscope to test point TP (TEO) on BD board.
2. Turned Power switch on.
3. Put disc (YEDS-18) in to play the number five track.
4. Confirm that oscilloscope waveform is clear and check RF
signal level is correct or not.
• SF signal
VOLT/DIV: 200 mV
TIME/DIV: 500 ns
level:
1.3 ± 0.3 Vp-p
Note: Clear RF signal waveform means that the shape “≈” can be clearly
distinguished at the center of the waveform.
– 20 –
E-F Balance (1 Track Jump) check
(Without remote commander)
Adjustment Location:
[BD BOARD] (Conductor Side)
oscilloscope
RF
BD board
VC
+
–
Procedure:
1. Connect oscilloscope to test point TP (TEO) on BD board.
2. Turned Power switch on.
3. Put disc (YEDS-18) in to play the number five track.
4. Press the “P (Pause)” button. (Becomes the 1 track jump
mode)
5. Check the level B of the oscilloscope’s waveform and the A
(DC voltage) of the center of the Traverse waveform.
Confirm the following:
A–B
2 (A + B)
FOK
CNU101
TP (TEO)
TP (VC)
IC101
TEO
FEO
GND
IC103
× 100 = ±7 (%)
1 track jump waveform
Center of the waveform
B
A (DC voltage)
0V
symmetry
level : 500 mV ± 100 mVp-p
– 21 –
CNU102
IC
I02
SECTION 7
DIAGRAMS
7-1.
IC PIN FUNCTION DESCRIPTION
• MAIN BOARD IC301 µPD780018YGF-028-3BA (SYSTEM CONTROLLER)
Pin No.
Pin Name
I/O
Function
1
TA-MUTE
O
Line muting on/off control signal output terminal “L”: muting on
2
DBFB-H/L
O
DBFB normal/high selection signal output to the M62427FP (IC201)
“L”: DBFB high, “H”: DBFB low
3
427-LAT
O
Serial data latch pulse output to the M62427FP (IC201)
4
K-CON-LAT
O
Serial data latch pulse output terminal Not used (open)
5
K-CON-ON
O
On/off selection signal output of the key control circuit “L”: on Not used (open)
6
F-RELAY
O
Relay drive signal output for the speaker protect “H”: on
7
R-RELAY
O
Relay drive signal output for the speaker protect “H”: on Not used (open)
8
PL-RELAY
O
Relay drive signal output for the speaker protect “H”: on Not used (open)
9
TEST
I
Test terminal
10
X2
O
Main system clock output terminal (5 MHz)
Main system clock input terminal (5 MHz)
Connected to ground
11
X1
I
12
VDD
—
Power supply terminal (+5V)
13
XT2
O
Sub system clock output terminal (32.768 kHz)
14
XT1
I
Sub system clock input terminal (32.768 kHz)
15
RESET
I
System reset signal input from the reset signal generator (IC302) “L”: reset
For several hundreds msec. after the power supply rises, “L” is input, then it changes to “H”
16
(INT/IN)
I
Connected to ground
17
(INT/IN/OUT)
I
Connected to ground
18
SCOR
I
Subcode sync (S0+S1) detection signal input from the CXD2519Q (IC103)
19
SOFT-TEST
O
Output terminal for the software test (open)
20
AC-CUT
I
AC off detection signal input from the reset signal generator (IC302)
21
RDS-INT
I
Serial data reading clock signal input for the radio data system Not used (fixed at “L”)
22
RDS-DATA
I
Serial data input for the radio data system Not used (open)
23
VDD
—
Power supply terminal (+5V)
24
AVDD
—
Power supply terminal (+5V) (for A/D conversion)
25
ADJ
I
Setting terminal for the CD test mode Normally: fixed at “H”
26
A-SHUT
I
Shut off detection signal input from the deck-A side reel pulse detector (Q1001)
27
B-SHUT
I
Shut off detection signal input from the deck-B side reel pulse detector (Q1002)
28
B-HALF
I
Detection input from the deck-B half detect switch (S1006)
29
CLK-CHECK
I
Not used (fixed at “L”)
30
SPEC-IN
I
Setting terminal for the version
31
ADJ2
I
Setting terminal for the CD test mode Normally: “L”
32
DEMO-MODE
I
Setting terminal for the demonstration H/L Fixed at “L”
33
AVSS
—
34
SQ-DATA-IN
I
Sub-code Q data input from the CXD2519Q (IC103)
35
NCO
O
Not used (open)
36
Ground terminal (for A/D conversion)
SQ-CLK
O
Sub-code Q data reading clock signal output to the CXD2519Q (IC103)
37
SW-ON/OFF
O
Super woofer speaker on/off control signal output terminal Not used (open)
38
FUNC1
I
Setting terminal for the function 1 Fixed at “L”
39
FUNC2
I
Setting terminal for the function 2 Fixed at “L”
40
VSS
—
Ground terminal
41
VOL-LAT
O
Serial data latch pulse output terminal Not used (open)
42
PL-LAT
O
Serial data latch pulse output terminal Not used (open)
43
COM-DIN
I
Serial data input terminal Not used (fixed at “L”)
– 22 –
Pin No.
Pin Name
I/O
Function
44
COM-DOUT
O
Serial data output to the M62427FP (IC201)
45
COM-CLK
O
Serial data transfer clock signal output to the M62427FP (IC201)
46
CD-POWER
O
Power on/off control signal output for the CD mechanism deck section
“H”: power on, “L”: standby
47
CD-DATA
O
Serial data output to the CXD2519Q (IC103)
48
CD-CLK
O
Serial data transfer clock signal output to the CXD2519Q (IC103)
49
MSM-CND
O
Command data output terminal Not used (open)
50
MSM-BUSY
I
Busy signal input terminal “L”: busy status Not used (fixed at “L”)
51
MSM-LAT
O
Serial data latch pulse output terminal Not used (open)
52
MSM-NAR
O
NAR signal output terminal Not used (open)
53
MSM-CH
O
Channel select signal output terminal Not used (open)
54
INPUTCHANGE
O
Attenuate control (–5 dB) signal output for the input gain control
“L”: VIDEO, “H”: MD
55
IIC-DATA
I/O
Communication data bus with the fluorescent indicator tube driver (IC601)
56
IIC-CLK
I/O
Communication data reading clock signal input or transfer clock signal output with the fluorescent indicator tube driver (IC601)
57
XRST
O
Reset signal output to the CXA1992AR (IC101), BA5941FP (IC102) and CXD2519Q (IC103) on
the CD mechanism deck section “L”: reset
58
XLT
O
Serial data latch pulse output to the CXD2519Q (IC103)
59
WDCL
O
Word clock signal output terminal Not used (open)
60
TBL-L
O
Motor drive signal output to the disc tray turn motor driver (IC201) *1
61
TBL-R
O
Motor drive signal output to the disc tray turn motor driver (IC201) *1
62
TRAY-LED
O
LED drive signal output for the CD tray LED indicate “H”: LED on
63
LOAD-OUT
O
Motor drive signal output terminal Not used (open)
64
LOAD-IN
O
Motor drive signal output terminal Not used (open)
65
ST-CLK
O
PLL serial data transfer clock signal output to the FM/AM tuner unit
66
ST-DIN
I
PLL serial data input from the FM/AM tuner unit
67
ST-DOUT
O
PLL serial data output to the FM/AM tuner unit
68
ST-CE
O
PLL chip enable signal output to the FM/AM tuner unit
69
TUNED
I
Tuning detection signal input from the FM/AM tuner unit “L”: tuned
70
STEREO
I
FM stereo detection signal input from the FM/AM tuner unit “L”: stereo
71
VSS
—
Ground terminal
72
ST-MUTE
O
Tuner muting control signal output to the FM/AM tuner unit “L”: muting on
73
SENS2
I
Internal status (SENSE) signal input from the CXA1992AR (IC101)
74
SENS
I
Internal status (SENSE) signal input from the CXD2519Q (IC103)
75
DISC-SENS
I
Disc status detection signal input terminal Not used (open)
76
T-SENS
I
Disc tray status detection signal input from the disc tray sensor (IC202)
77
UP SW
I
Detection input from the UP switch (S201)
78
ENC3
I
79
ENC2
I
80
ENC1
I
81
OUT-OPEN
I
Disc tray open/close detect switch input terminal “L”: open, “H”: close Not used (open)
82
CAP-H/N
O
High/normal speed selection signal output of the capstan motor (M1)
“L”: high speed, “H”: normal speed
83
A-TRG
O
Motor drive signal output to the trigger motor driver (IC1502)
84
B-TRG
O
Motor drive signal output to the trigger motor driver (IC1502)
85
TRG-LOW
O
Motor control signal output to the trigger motor driver (IC1502)
Rotary encoder pulse input for the disc tray address detect Not used (open)
– 23 –
Pin No.
Pin Name
I/O
Function
86
CAP-M-ON/OFF
O
Capstan motor (M1) on/off control signal output terminal “L”: capstan motor on
87
PB-A/B
O
Deck-A/B selection signal output to the HA12203NT (IC1501) “L”: deck-A, “H”: deck-B
88
EQ-H/N
O
Normal/high speed selection signal output to the HA12203NT (IC1501)
“L”: normal speed, “H”: high speed
89
BIAS
O
Recording bias on/off selection signal output to the HA12203NT (IC1501)
“L”: bias off, “H”: bias on
90
REC-MUTE
O
Recording muting on/off selection signal output to the HA12203NT (IC1501)
“L”: muting on, “H”: muting off
91
NR-ON/OFF
O
Dolby NR on/off selection signal output to the HA12203NT (IC1501)
“L”: dolby off, “H”: dolby on
92
R/P-PASS
O
Recording/playback/pass selection signal output to the HA12203NT (IC1501)
“L”: recording mode
93
TC-MUTE
O
Line muting on/off selection signal output to the HA12203NT (IC1501)
“L”: muting off, “H”: muting on
94
A-PLAY-SW
I
Detection input from the deck- A play detect switch (S1001) “H”: deck-A play
95
B-PLAY-SW
I
Detection input from the deck- B play detect switch (S1002) “H”: deck-B play
96
RELAY
O
Recording/playback select signal output to the REC/PB switch (IC602)
“L”: playback, “H”: recording
97
A-HALF
I
Detection input from the deck-A cassette detect switch (S1003)
“L”: cassette in, “H”: no cassette
98
POWER
O
Power on/off control signal output for the audio system (+5V) and deck, panel, audio system
(+7V and –7V) “L”: power on, “H”: standby
99
SW-F-CON
O
Super woofer mode control signal output to the M62427FP (IC201) “H”: music, “L”: movie
100
STK-MUTE
O
Power amplifier on/off selection signal output terminal “L”: on, “H”: standby
*1 Disc tray turn motor (M201) control
Mode
Terminal
STOP
COUNTERCLOCKWISE
CLOCKWISE
BRAKE
TBL-L (pin ^º)
“H”
“L”
“H”
“L”
TBL-R (pin ^¡)
“H”
“H”
“L”
“L”
– 24 –
HCD-XB66K
• PANEL BOARD IC601 TMP87CH75F-6659
(FLUORESCENT INDICATOR TUBE DRIVE, LED DRIVE, KEY CONTROL)
Pin No.
Pin Name
I/O
Function
Pin No.
Pin Name
I/O
Function
37
KEY-5
I
Key input terminal (A/D input) (S641 to 647, 661 to 666)
DECK A ·/ª/p/0/), DOLBY NR, DIRECTION, DIRECT PLAY DISC 1/2/3/4/5, DJ
MIX FLASH keys input
1
SEG-35
O
Segment drive signal output to the fluorescent indicator tube (FL601)
2
V-LOAD
—
Power supply terminal (–30V) (for fluorescent indicator tube drive)
3
LED1
O
LED drive signal output terminal (TUNER/BAND)
4
LED2
O
LED drive signal output terminal (ENTER/NEXT, GROOVE)
38
DOOR SW
I
CD door switch (S691 (6 OPEN)) input terminal
5
LED3
O
LED drive signal output terminal (SUPER WOOFER, CD P)
39
SIRCS
I
Remote control signal input from the remote control receiver (IC602)
6
LED4
O
LED drive signal output terminal (CD ·)
40
VOL-B
I
Rotary encoder pulse input from the S701 (VOLUME)
LED drive signal output terminal (DECK B ª)
41
JOG-B
I
Jog dial pulse input from the S711 (≠ AMS ± jog dial)
SPEANA-1
I
Spectrum analyzer drive (for low frequency) signal input terminal
7
LED5
O
8
LED6
O
LED drive signal output terminal (DECK B ·)
42
9
LED7
O
LED drive signal output terminal (TAPE P, r REC)
43
SPEANA-2
I
Spectrum analyzer drive (for low and middle frequency) signal input terminal
10
LED8
O
LED drive signal output terminal (EFFECT, ENTER)
44
SPEANA-3
I
Spectrum analyzer drive (for middle and high frequency) signal input terminal
SPEANA-4
I
Spectrum analyzer drive (for high frequency) signal input terminal
I
Spectrum analyzer drive (for VACS, non-stop signal) signal input terminal
11
VSS
—
Ground terminal
45
12
X-OUT
O
System clock output terminal (8 MHz)
46
L+R
13
X-IN
I
System clock input terminal (8 MHz)
47
LED18
O
LED drive signal output terminal (NON-STOP)
VASS
—
Ground terminal
14
RESET
I
System reset signal input from the reset signal generator (IC302) “L”: reset
For several hundreds msec. after the power supply rises, “L” is input, then it changes to “H”
48
49
VAREF
I
15
LED9
O
LED drive signal output terminal (FILE 1, FILE 2)
50
VDD
—
16
LED10
O
LED drive signal output terminal (FILE 3, FILE 4)
51 to 66
GR-1 to GR-16
O
Grid drive signal output to the fluorescent indicator tube (FL601)
17
TEST
I
Connected to ground
67 to 100 SEG-1 to SEG-34
O
Segment drive signal output to the fluorescent indicator tube (FL601)
18
LED11
O
LED drive signal output terminal (FILE 5, P FILE)
19
LED12
O
LED drive signal output terminal (OTHERS, MUSIC)
20
LED13
O
LED drive signal output terminal Not used (open)
21
LED14
O
LED drive signal output terminal Not used (open)
22
LED15
O
LED drive signal output terminal (DECK A ·)
23
LED16
O
LED drive signal output terminal (DECK A ª)
24
VOL-A
I
Rotary encoder pulse input from the S701 (VOLUME)
25
LED17
O
LED drive signal output terminal Not used in this set
26
JOG-A
I
Jog dial pulse input from the S711 (≠ AMS ± jog dial)
27
CLOCK
I/O
Communication data reading clock signal input or transfer clock signal output with the system
controller (IC301)
28
DATA
I/O
Communication data bus with the system controller (IC301)
29
LED SELECT
O
LED selection signal output terminal
30
VDD
—
Power supply terminal (+5V)
31
VSS
—
Ground terminal
32
MODEL
I
Destination setting terminal
I
Key input terminal (A/D input) (S601 to 607, 609 to 616)
ENTER/NEXT, TUNER MEMORY, TUNING MODE, TUNER/BAND, TUNING +/–,
STEREO/MONO, FUNCTION, GROOVE, GEQ 4/9/(/$, SUPER WOOFER, SUPER W
MODE keys input
33
KEY-1
34
KEY-2
I
Key input terminal (A/D input) (S621 to 625, 651 to 659)
EFFECT, SOUND CONTROL WAVE, KARAOKE PON/MPX, SOUND CONTROL
SURROUND, P FILE MEMORY, DECK B ·/ª/)/0/p/P, r REC, H SPEED DUB,
CD SYNC keys input
35
KEY-3
I
Key input terminal (A/D input) (S619, 620, 676 to 679, 681 to 686)
GEQ CONTROL, ENTER, CD ·/p/P, DISC SKIP, CD ), REPEAT, PLAY MODE,
1/ALL DISCS, EDIT, CD 0 keys input
36
KEY-4
I
Key input terminal (A/D input) (S627 to 634, 667, 668)
SPECTRUM ANALYZER, DISPLAY/DEMO, POWER, t/CLOCK SET, REC, DAILY 1/2,
SLEEP, NON-STOP, DJ MIX LOOP keys input
— 25 —
Reference voltage (+5V) input terminal (for A/D conversion)
Power supply terminal (+5V)
— 26 —
HCD-XB66K
BLOCK DIAGRAM – CD SECTION –
DIGITAL SIGNAL PROCESSOR,
CLV SERVO PROCESSOR,
DIGITAL FILTER, D/A CONVERTER
IC103
TTL
IIL
DEFECT
AMP
IIL
IIL
TTL
OPTICAL PICK-UP
(KSS-213D/Q-NP)
FOCUS
ERROR
AMP
FEO
FE BIAS
1
2
FEI
SENS1
C.OUT
SENS2
FOCUS PHASE
COMPENSATION
FEO
22
20
21
19
23
25
24
26
DATO
15
CLKO
17
XLTO
16
SEIN
13
CNIN
14
6
ERROR
CORRECTOR
DIGITAL CLV
8 7 9 10 12 11 75 76 77 21
89
6
42
F
E
TRACKING TEO
45
ERROR
AMP
I-V
AMP
47
TEI
TRACKING PHASE
COMPENSATION
TAO
CLOCK
GENERATOR
90
S101
(LIMIT)
13
SYSTEM CONTROLLER
IC301 (1/3)
LASER DIODE
ON : When the optical pick-up
is inner position.
57
XRST
PD
LD
AUTOMATIC
POWER CONTROL
Q101
36
LD
LD
AMP
PD
AMP
PD
37
73 SENS2
71
EMPH
72
GFS
61
WFCK
74
GTOP
58
70
AOUT1
84
95
85
94
BUFFER
86
X101
16.9344MHz
40
+5V
41
DOUT
DIGITAL
OUT
TIMING
LOGIC
CPU INTERFACE
26 27 28 29 64
100
16K
RAM
AOUT2
EMPHI
SUB-CODE
PROCESSOR
PWM &
INTEGRATOR
AIN1
6
TTL
DATA
CLK
XLT
LOCK
XRST
73
AIN2
RF AMP,
FOCUS/TRACKING
SERVO
IC101 (1/2)
FOK
LOUT2
MIRR
AMP
IIL DATA REGISTER
10
23
FOCUS OK
AMP
F
E
27
NOISE
SHAPER
LOUT1
FOK
ASYO
OVER
SAMPLING
DIGITAL
FILTER
93
R-CH
CD-L
FOCUS OK
COMPARATOR
2
ASYI
PCMDI
53
SERIAL
BCKI
55
INPUT
LRCKI INTERFACE
51
52
54
50
63
62
49
C4M
47
1
EFM
DEMODULATOR
DIGITAL PLL
PCMD
BCK
LRCK
C2PO
RFCK
WDCK
XTAO
46
ASYMMETRY
CORRECTION
INTERNAL BUS
32
RF
D/A
INTERFACE
FILO
CLTV
PCO
FILI
RFI
PD2
44
XTAI
C
39
33
CKOUT
B
I-V AMP
5
RFO
SQSO
SQCK
SENS
DATA
CLOK
XLAT
SCOR
SBSO
EXCK
SPOD
D
XRST
A
RF
SUMMING
AMP
+
PD2 I-V AMP
LOCK
XROF
DETECTOR
MON
MDP
MDS
38
PD1
SERVO AUTO SEQUENCER
4
FILTER
39 42 38 40
PD1 I-V AMP
A
(Page 31)
SQ-DATA-IN
SQ-CLK
SENS
CD-DATA
CD-CLK
XLT
SCOR
34
36
74
47
48
58
18
OPTICAL
TRANSCEIVER
IC391
IC391
CD DIGITAL
OUT
OPTICAL
S201
(UP)
UPSW 77
9
MUTE
OUT4A
16
OUT4B
15
TRACKING
COIL DRIVE
IN4A
OUT3A
18
OUT3B
17
FOCUS
COIL DRIVE
IN3B
27
26
24
OP
OUT
BUFFER
OP+,
OP–
FOCUS/TRACKING COIL DRIVE,
SPINDLE/SLED MOTOR DRIVE
IC102
16
M102
(SLED)
M
OUT2A
IN2A
SLED
11
6
12 OUT2B MOTOR DRIVE
M101
(SPINDLE)
M
OUT1A
13
IN1B
SPINDLE
OUT1B
3
MOTOR DRIVE
14
DISC TRAY SENSOR
IC202
T-SENS 76
22, 23
(TRACKING)
2-AXIS
DEVICE
(FOCUS)
7-2.
DISC TRAY TURN MOTOR DRIVE
IC201
TBL-L 60
TBL-R 61
16
SLO
SLED
AMP
SLED SERVO
IC101 (2/2)
SLP
IN1
9
IN2
1
MOTOR
DRIVE
OUT1
OUT2
7
3
M
M201
(DISC TRAY TURN)
14
TRAY-LED 62
LED DRIVE
Q201
D201
(DISC No.)
• SIGNAL PATH
: CD PLAY
: DIGITAL OUT
— 27 —
— 28 —
HCD-XB66K
BLOCK DIAGRAM – TAPE DECK SECTION –
DECK PROCESS
DECK A/B SELECT, PB/REC EQ AMP,
DOLBY NR AMP
IC1501
• SIGNAL PATH
: PLAYBACK (DECK A)
DOLBY PASS
HP101
(PLAYBACK)
70
2
4
120
PB LEVEL (L)
(DECK A)
R-CH
PB-A/B
NORM/HIGH
BIAS-ON/OFF
RM-ON/OFF
NR-ON/OFF
REC/PB/PASS
LM-ON/OFF
R-CH
R-CH
RIN (L)
9
6
REC
EQ AMP
EQ OUT
(L)
11
10
27
MSIN
AMS
CIRCUIT
13 15
12 14 16 17 18 19 20
21
RV301
PB LEVEL (L)
(DECK B)
MAOUT
28
A 120/70
B 120/70
PB EQ AMP
(DECK B)
IC601
L-CH
BUFFER
BIAS
CONTROL
CIRCUIT
: RECORD
(Page 31)
REC OUT (L)
L.P.F.
HRPE101 (1/2)
(RECORD/PLAYBACK)
B
+
R-CH
NORM
25
CROM
24
METAL
23
: PLAYBACK (DECK B)
PB-L
8
DOLBY NR
AMP
CIRCUIT
BIN (L)
RV311
R-CH
PB OUT (L)
AIN (L)
EQ IN (L)
PB EQ AMP
(DECK A)
IC611
L-CH
RV1501
REC LEVEL (L)
(DECK B)
MSOUT
REC-L
C
(Page 32)
REC/PB SWITCHING
IC602
S1004
(DECK A 120/70)
1
3
R-CH
R-CH
S1008
(DECK B 120/70)
4
2
C331, L331
BIAS
TRAP
R-CH
RV652
RV651
TAPE SPEED
(HIGH)
TAPE SPEED
(NORMAL)
Q1533
16
27
B-SHUT
82
86
TRG-LOW
B-TRG
A-TRG
SYSTEM CONTROLLER
IC301 (2/3)
CAP-M-ON/OFF
26
CAP-H/N
87 88 89 90 91 92 93
A-SHUT
BIAS OSC
Q621, 622
96
94
95
97
28
85
84 83
S1003
(DECK A HALF)
D+5V
TRIGGER MOTOR DRIVE
IC1502
S1006
(DECK B HALF)
S1005
(DECK A REC)
S1002
S1001
(DECK A PLAY) (DECK B PLAY)
S1009
(DECK B REC)
IN1
5
IN2
6
MOTOR
DRIVE
OUT1
OUT2
VZ
4
D+5V
TRIGGER
MOTOR CONTROL
Q1534, 1535
— 29 —
M1
(CAPSTAN)
CAPSTAN
MOTOR CONTROL
Q1531, 1532
B-HALF
BIAS OSC
T621
+12V (M)
M
A-HALF
HRPE101 (2/2)
(ERASE)
B+
(A+7V)
ROTATION
DETECT SENSOR
(DECK B)
Q1002
PB-A/B
EQ-H/N
BIAS
REC-MUTE
NR-ON/OFF
R/P-PASS
TC-MUTE
REC BIAS
SWITCH
Q623
ROTATION
DETECT SENSOR
(DECK A)
Q1001
B-PLAY-SW
RV341
REC BIAS (L)
(DECK B)
RELAY
RV441
REC BIAS (R)
(DECK B)
CAPSTAN MOTOR
CONTROL SWITCH
Q651
A-PLAY-SW
7-3.
— 30 —
2
10
M
M2
(TRIGGER)
HCD-XB66K
BLOCK DIAGRAM – MAIN SECTION (1/2) –
RV761
ECHO LEVEL
IC761
1
KEY
8
CONTROL
O
P
J761
MIC 1
(Page 35)
(Page 35)
(Page 30)
REC-L
MIC AMP
IC760 (2/2)
MIC AMP
IC760 (1/2)
• SIGNAL PATH
: CD PLAY
C
: TAPE PLAY
RV760
J101 (2/2)
L
MIC LEVEL
: RECORD
VIDEO/MD
(AUDIO) OUT
R-CH
: TUNER (FM/AM)
R
: MIC INPUT
J101 (1/2)
PHONO EQ
AMP
IC101
PHONO IN
R-CH
ATTENUATOR
(–5dB)
Q101
13
INH
A B
6
10 9
71
KEY
IN2
IN-2B
IN-2A
INPUT
SELECT
R-CH
B
F OUT2
45
44
VOL
VOLUME OUT2
43
VOL CONTROL
IN2
42
BB
IN2 BASS BOOST
CONTROL
CIRCUIT
BUF
OUT2
L-CH
38
G
(Page 33)
MUTING
Q204
CPU INTERFACE
CD-L
29 28 30
(Page 30)
GRAPHIC
EQUALIZER
CONTROL
CIRCUIT
R-CH
PORT-B
PORT-A
PORT-C
A
KEY
OUT2
SOUND
CONTROL
CIRCUIT
R-CH
(Page 28)
REC
2B
REC
2A
69
12
14
15
11
61
62
64
FUNCTION SWITCH
IC102
L
R
65
INPUT SELECT SWITCH,
GRAPHIC EQUALIZER CONTROL,
ELECTRICAL VOLUME
IC201
COMMAND
R-CH
BUF IN2
VIDEO/MD
(AUDIO) IN
R-CH
DATA
CLOCK
LATCH
R
BB12,
BB22
L
41, 40
39
33 32 34
PB-L
FEED BACK
SWITCH
Q203
D291
FEED BACK
+
R-CH
H
(Page 33)
SPEANA
MIXING AMP
IC231
DBFB CONTROL
SWITCH
Q202
R-CH
FM/AM TUNER UNIT
R-CH
FM 75Ω
(Page 35)
F
SPEANA
R-CH
(Page 36)
ST-DIN
ST-DOUT
ST-CLK
ST-CE
(Page 36)
MUTING CONTROL
SWITCH
Q231, 232
DATA, CLK
+5V
POWER
K
RESET SIGNAL
GENERATOR
IC302
CD-POWER
L
RESET
E
(Page 35)
RESET
SWITCH
Q301
DATA
CLK
X302
32.768kHz
X301
5MHz
Q
98
55 56
99
2
1
20
AC-CUT
SYSTEM CONTROLLER
IC301 (3/3)
15
RESET
46
F-RELAY
14
STK-MUTE
13
TA-MUTE
X2
16
11
DBFB-H/L
10
SW-F-CON
54 4 5 44 45 3
IIC-DATA
IIC-CLK
68 65 66 67 69 70 72
INPUT-CHANGE
K-CON-LAT
K-CON-ON
COM-DOUT
COM-CLK
427-LAT
(Page 36)
POWER
ST-R
D
CD-POWER
FM ANT
(Page 35)
XT1
ST-L
R-CH
XT2
FM ANT
ATTENUATOR
CONTROL SWITCH
Q102, 103
AM ANT ST-MUTE
STEREO
AM ANT TUNED
AM
SWITCHING
Q201
X1
ANTENNA
ST-CE
ST-CLK
ST-DIN
ST-DOUT
TUNED
STEREO
ST-MUTE
7-4.
100
6
(Page 34)
RELAY
STK-MUTE
J
I
(Page 33)
— 31 —
— 32 —
HCD-XB66K
BLOCK DIAGRAM – MAIN SECTION (2/2) –
J760
PHONES
• SIGNAL PATH
: CD PLAY
G
1
L-CH
POWER AMP
IC801 (1/2)
10
-1
L-CH (+)
(Page 32)
POWER AMP
IC801 (2/2)
-1
L-CH (–)
13
H
+
L
+
–
R
TM131
SPEAKER
IMPEDANCE
USE 8 – 16Ω
FAN MOTOR
DRIVE
Q191, 192
6
FEED BACK
+
–
D191
17
D192
7-5.
OVER LOAD
DETECT
Q801, 851
M
M100
(FAN)
(Page 32)
D811
1
R-CH
17
POWER AMP
IC821 (1/2)
10
R-CH (+)
POWER AMP
IC821 (2/2)
13
R-CH (–)
-2
-2
6
OVER LOAD
DETECT
Q821, 871
RELAY DRIVE
Q141, 142
RELAY
J
(Page 32)
RY141
STANDBY SWITCH
Q283
RY142
D831
2
I
STK-MUTE
PROTECTOR
IC281
OFFSET
DETECT
(Page 32)
OVER LOAD
DETECT SWITCH
Q282
FLIP
FLOP
1
VCC ON
MUTE
RELAY
DRIVE
6
OVER LOAD
DETECT
AC OFF
DETECT
4
RELAY SWITCH
Q281
16
7
AC OFF
M
(Page 36)
— 33 —
— 34 —
HCD-XB66K
BLOCK DIAGRAM – DISPLAY/KEY CONTROL/POWER SUPPLY Section –
FLUORESCENT INDICATOR TUBE DRIVE,
LED DRIVE, KEY CONTROL
IC601
FLUORESCENT
INDICATOR TUBE
FL601
14 RESET
(Page 32)
GR-1 – GR-16
SPEANA-1
SPEANA-2
SPEANA-3
SPEANA-4
46 L+R
D+5V, A+5V
CD MECHANISM DECK
SECTION B+
B+
SWITCH
Q901, 902
AUDIO D+5V
B+
SWITCH
Q905, 906
D+5V
PANEL SECTION B+
SYSTEM CONTROLLER
(IC301) B+
K
(Page 31)
L
(Page 31)
M
(Page 34)
D913
D914
+5V
REGULATOR
IC903
D301, 302
S691
6 OPEN
38 DOOR SW
+7V
(CD M+7V)
LED1 – LED12, LED15 – LED18
26 JOG-A
41 JOG-B
13
D611 – 625, 631, 632,
D635 – 638, 641, 645 – 647
CAPSTAN MOTOR DRIVE CIRCUIT,
TRIGGER MOTOR DRIVE CIRCUIT B+
(page 31)
(page 31)
O
P
+10V
(FM/AM TUNER UNIT B+)
IC502
MULTIPLEXER
5
IC501
KEY CONTROL
X601
8MHz
14 VCC
+5V
RECT
D906, 907
–30V
REGULATOR
Q904
RECT
D908, 909
Thai model
TO
FLUORESCENT INDICATOR TUBE
(FL601)
3
SL-P 15
+12V
REGULATOR
IC904
4
14
22 LPF1 IN
20 HPF IN
+10V
REGULATOR
Q903
–30V
FL DRIVER (IC601)
R-CH
VF1
VF2
AC IN
9
SL-P 9
POWER AMP
(IC801, 821)
SL-P 7
B+
B–
Q501
SWITCH
RECT
D800
VOLTAGE
SELECT SWITCH
S901
S901
VOLTAGE
SELECTOR
Q501
SWITCH
Q
— 35 —
D952
D951
RECT
D902 – 905
–7V
LED DRIVE
Q604 – 611,
Q614 – 619, 621, 622
24 VOL-A
40 VOL-B
12
POWER TRANSFORMER
T901
+7V/–7V
REGULATOR
IC901
Except Thai model
5
16
ROTARY
ENCODER
S701
39 SIRCS
D671 – 674
(BACK LIGHT)
TC, PANEL, AUDIO
4
S701
VOLUME
AC OFF
+7V
45
(JOG DIAL)
ROTARY
ENCODER
S711
LED SELECT 29
X-IN
S711
≠ AMS ±
+7V
REGULATOR
IC902
REGULATOR
CONTROL SWITCH
Q907
Q601
X-OUT
REMOTE CONTROL
RECEIVER
IC602
B+ SWITCH
Q602, 603
D+5V
S601 – 607, 609 – 616, 619 – 625,
S627 – 634, 641 – 647, 651 – 659,
S661 – 668, 676 – 679, 681 – 686
33 – 37
D
(Page 31)
SPEANA
42
43
44
45
BAND-PASS
FILTER CIRCUIT
C621 – 632,
D601 – 607,
R621 – 629,
R631 – 638
CD-POWER
44
E
RESET
POWER
28 DATA
27 CLOCK
67 – 100, 1
(Page 31)
SEG1 – SEG35
DATA
CLK
51 – 66
DATA, CLK
3 – 10, 15, 16, 18, 19, 22, 23, 25, 47
F
KEY-1 – KEY-5
7-6.
(page 32)
— 36 —
HCD-XB66K
7-7.
CIRCUIT BOARDS LOCATION
THIS NOTE IS COMMON FOR PRINTED WIRING BOARDS AND SCHEMATIC DIAGRAMS.
(In addition to this, the necessary note is printed in each block.)
TRANS board
PANEL board
KEY-CON board
Note on Schematic Diagram:
• All capacitors are in µF unless otherwise noted. pF: µµF
50 WV or less are not indicated except for electrolytics
and tantalums.
• All resistors are in Ω and 1/ 4 W or less unless otherwise
specified.
¢
•
: internal component.
• 2 : nonflammable resistor.
• 5 : fusible resistor.
• C : panel designation.
Note: The components identified by mark ! or dotted line
with mark ! are critical for safety.
Replace only with part number specified.
MAIN board
HP/MIC board
Note on Printed Wiring Boards:
• X : parts extracted from the component side.
¢
•
: internal component.
• b : Pattern from the side which enables seeing.
(The other layers' patterns are not indicated.)
Caution:
Pattern face side:
(Side B)
Parts face side:
(Side A)
Parts on the pattern face side seen from
the pattern face are indicated.
Parts on the parts face side seen from
the parts face are indicated.
• Indication of transistor.
C
POWER AMP board
TC-A SW
board
•
•
•
•
•
LED board
•
•
CD-A SW board
TC-B SW board
DOOR SW board
CD-B2 SW board
CD-B1 SW board
•
U : B+ Line.
V : B– Line.
H : adjustment for repair.
Voltages are taken with a VOM (Input impedance 10 MΩ).
Voltage variations may be noted due to normal production tolerances.
Waveforms are taken with a oscilloscope.
Voltage variations may be noted due to normal production tolerances.
Circled numbers refer to waveforms.
Signal path.
F
: TUNER (FM/AM)
E
: PB (DECK A)
d
: PB (DECK B)
G : REC (DECK B)
J
: CD
c : digital out
N : MIC INPUT
Abbreviation
IA
: Indonesian
TH
: Thai
Q
Q
B C
E
These are omitted.
MOTOR board
LEAF SWITCH
board
CD MOTOR board
BD board
AUDIO board
BD LED board
TABLE SENSOR board
— 37 —
These are omitted.
B E
— 38 —
HCD-XB66K
7-8. PRINTED WIRING BOARD – CD SECTION (1/2) –
• See page 37 for Circuit Boards Location. • See page 38 for Note.
• Semiconductor
Location
Ref. No. Location
IC101
IC201
IC501
C-5
B-5
C-6
Q101
C-3
MAIN BOARD
CN202
(Page 51)
16
— 39 —
— 40 —
HCD-XB66K
7-9. SCHEMATIC DIAGRAM – CD SECTION (1/2) –
• See page 38 for Note. • See page 77 for Waveforms. • See page 78 for IC Block Diagrams.
The components identified by mark ! or dotted line
with mark ! are critical for safety.
Replace only with part number specified.
• Voltages and waveforms are dc with respect to ground
under no-signal conditions.
no mark : STOP
(
) : PLAY
— 41 —
— 42 —
HCD-XB66K
7-10. PRINTED WIRING BOARDS – CD SECTION (2/2) –
• See page 37 for Circuit Boards Location. • See page 38 for Note.
1
2
3
4
5
6
7
8
9
10
A
TABLE SENSOR
BOARD
B
CD MOTOR
BOARD
C
(DISC TRAY TURN)
D
E
F
BD LED
BOARD
16
— 43 —
MAIN BOARD
CN203
(PAGE 51)
CD MOTOR
BOARD
— 44 —
HCD-XB66K
7-11. SCHEMATIC DIAGRAM – CD SECTION (2/2) –
• See page 38 for Note. • See page 80 for IC Block Diagrams.
• Voltages and waveforms are dc with respect to ground
under no-signal conditions.
no mark : STOP
— 45 —
— 46 —
HCD-XB66K
7-12. PRINTED WIRING BOARDS – TAPE DECK SECTION –
• See page 37 for Circuit Boards Location. • See page 38 for Note.
1
2
3
4
5
6
7
8
9
10
11
12
13
14
(
A
(
)
)
MAIN BOARD
CN205
(PAGE 51)
MOTOR
BOARD
(
)
B
C
(
AUDIO BOARD
CN651
D
E
F
G
H
(DECK B PLAY)
(DECK A PLAY)
I
16
(DECK A HALF) (DECK A 120/70)
(DECK A REC)
(DECK B HALF)
— 47 —
(DECK B 120/70) (DECK B REC)
MAIN BOARD
CN206
(PAGE 51)
— 48 —
)
HCD-XB66K
7-13. SCHEMATIC DIAGRAM – TAPE DECK SECTION –
• See page 38 for Note. • See page 80 for IC Block Diagrams.
The components identified by mark ! or dotted line
with mark ! are critical for safety.
Replace only with part number specified.
• Voltages and waveforms are dc with respect to ground
under no-signal conditions.
no mark : PLAYBACK
(
) : RECORD
— 49 —
— 50 —
HCD-XB66K
7-14. PRINTED WIRING BOARD – MAIN SECTION –
• See page 37 for Circuit Boards Location. • See page 38 for Note.
• Semiconductor
Location
Ref. No. Location
JW393
JW394
P
KEY-CON BOARD
CN501
(PAGE77)
R312
R311
16
— 51 —
— 52 —
D141
D142
D191
D192
D291
D301
D302
D303
D304
D305
D306
D307
D309
D902
D903
D904
D905
D906
D907
D908
D909
D910
D911
D912
D913
D914
D915
D951
D952
G-11
I-10
F-12
F-12
H-9
E-5
E-5
E-5
E-5
E-5
E-6
F-5
F-5
I-6
I-6
I-6
I-6
I-5
I-4
I-3
I-3
I-4
I-4
F-4
F-3
F-3
H-3
I-6
I-6
IC101
IC102
IC201
IC231
IC281
IC301
IC302
IC391
IC901
IC902
IC903
IC904
IC1501
IC1502
A-11
B-11
D-10
G-7
H-9
D-5
E-5
A-12
G-4
G-5
F-4
H-4
B-2
C-2
Q101
Q102
Q103
Q141
Q142
Q151
Q191
Q192
Q201
Q202
Q203
Q204
Q231
Q232
Q251
Q252
Q253
Q254
Q281
Q282
Q283
Q301
Q901
Q902
Q903
Q904
Q905
Q906
Q907
Q1531
Q1532
Q1533
Q1534
Q1535
B-11
B-11
B-11
I-10
H-10
B-11
F-12
E-12
F-10
F-10
F-10
G-8
G-8
G-8
F-9
F-8
F-8
G-8
I-9
H-8
I-8
E-6
G-3
G-4
I-3
I-3
G-4
G-4
H-4
C-1
C-1
C-1
C-2
C-2
HCD-XB66K
7-15. SCHEMATIC DIAGRAM – MAIN SECTION (1/3) –
• See page 38 for Note. • See page 77 for Waveforms.
• Voltages and waveforms are dc with respect to ground
under no-signal (detuned) conditions.
no mark : FM
[
] : CD
— 53 —
(
〈〈
∗
) : VIDEO/MD (AUDIO)
〉〉 : PLAYBACK
: Impossible to measure
— 54 —
HCD-XB66K
7-16. SCHEMATIC DIAGRAM – MAIN SECTION (2/3) –
• See page 38 for Note. • See page 80 for IC Block Diagrams.
The components identified by mark ! or dotted line
with mark ! are critical for safety.
Replace only with part number specified.
— 55 —
• Voltages and waveforms are dc with respect to ground
under no-signal (detuned) conditions.
no mark : FM
[
] : CD
(
) : VIDEO/MD (AUDIO)
〈〈
〉〉 : PLAYBACK
— 56 —
HCD-XB66K
7-17. SCHEMATIC DIAGRAM – MAIN SECTION (3/3) –
• See page 38 for Note. • See page 80 for IC Block Diagrams.
• Voltages and waveforms are dc with respect to ground
under no-signal conditions.
no mark : PLAYBACK
(
) : RECORD
— 57 —
— 58 —
HCD-XB66K
7-18. PRINTED WIRING BOARD – POWER AMP SECTION –
• See page 37 for Circuit Boards Location. • See page 38 for Note.
• Semiconductor
Location
Ref. No. Location
D800
D801
D811
D821
D831
D841
D842
D851
D871
D891
D892
B-2
C-1
C-4
D-4
D-8
C-2
C-2
C-4
C-7
D-4
D-4
IC801
IC821
D-2
D-5
Q801
Q821
Q851
Q871
D-1
D-4
D-3
D-7
except TH
16
— 59 —
— 60 —
HCD-XB66K
7-19. SCHEMATIC DIAGRAM
• See page 38 for Note.
– POWER AMP SECTION –
The components identified by mark ! or dotted line
with mark ! are critical for safety.
Replace only with part number specified.
• Voltages and waveforms are dc with respect to ground
under no-signal (detuned) conditions.
no mark : FM
— 61 —
— 62 —
HCD-XB66K
7-20. PRINTED WIRING BOARD – PANEL SECTION (1/3) –
• See page 37 for Circuit Boards Location. • See page 38 for Note.
• Semiconductor
Location
Ref. No. Location
D601
D602
D603
D604
D605
D606
D607
D611
D612
D613
D614
D615
D616
D617
D618
D619
D620
D621
D622
D623
D624
D625
D-9
D-10
C-9
B-9
B-10
B-9
C-9
A-1
A-1
B-3
D-3
F-1
E-6
G-7
E-11
E-10
E-10
E-9
E-8
E-7
E-7
E-7
IC601
IC602
B-7
B-10
Q601
Q602
Q603
Q604
Q605
Q606
Q607
Q608
Q609
Q610
Q611
Q614
Q615
Q617
Q618
Q619
Q621
Q622
B-2
C-3
D-2
A-2
D-3
D-3
D-4
D-4
D-4
D-4
D-4
G-4
G-4
G-4
G-4
G-3
G-3
G-3
S617
KEY CONTROL
n
S618
KEY CONTROL
˜
16
— 63 —
— 64 —
HCD-XB66K
7-21. SCHEMATIC DIAGRAM
• See page 38 for Note.
– PANEL SECTION (1/3) –
• Voltages and waveforms are dc with respect to ground
under no-signal (detuned) conditions.
no mark : FM
74
— 65 —
— 66 —
HCD-XB66K
7-22. PRINTED WIRING BOARDS – PANEL SECTION (2/3) –
• See page 37 for Circuit Boards Location. • See page 38 for Note.
1
3
2
L
A
PANEL BOARD
NO801
(Page 64)
4
5
6
J760
J762
J761
PHONES
MIC2
MIC1
7
8
HEADPHONE-MIC BOARD
MIC LEVEL
ECHO LEVEL
RV761
B
C787
C782
R771
C781
C780
R772
C779
R773
C777
C789
JW106
C
7
IC761
14
R778
C779
1
R779
1
8
8
D763
R777
C784
R775
R776
C783
L761
D
C788
C786
R774
C791
D762
1
4
8
5
C785
D761
1-664-015-
11
(14)
E
F
G
16
— 67 —
— 68 —
9
10
HCD-XB66K
7-23. SCHEMATIC DIAGRAM
• See page 38 for Note.
– PANEL SECTION (2/3) –
4.7
0.8
• Voltages and waveforms are dc with respect to ground
under no-signal (detuned) conditions.
no mark : FM
— 69 —
— 70 —
HCD-XB66K
7-24. PRINTED WIRING BOARDS – PANEL SECTION (3/3) –
• See page 37 for Circuit Boards Location. • See page 38 for Note.
1
2
3
4
5
6
7
8
9
10
A
B
C
D
E
F
G
H
16
— 71 —
— 72 —
11
12
HCD-XB66K
7-25. SCHEMATIC DIAGRAM
• See page 38 for Note.
– PANEL SECTION (3/3) –
— 73 —
— 74 —
HCD-XB66K
7-26. PRINTED WIRING BOARD – POWER SUPPLY Section –
• See page 37 for Circuit Boards Location. • See page 38 for Note.
1
3
2
7-27. SCHEMATIC DIAGRAM
• See page 38 for Note.
4
– POWER SUPPLY SECTION –
5
EXCEPT TH
A
JW201
B
JW202
TH MODEL
EXCEPT TH
TH MODEL
C
D
The components identified by mark ! or dotted line
with mark ! are critical for safety.
Replace only with part number specified.
E
F
G
16
H
— 75 —
— 76 —
HCD-XB66K
7-28. SCHEMATIC DIAGRAM – KEY CONTROL SECTION –
• See page 38 for Note.
7-29. PRINTED WIRING BOARD – KEY CONTROL SECTION –
• See page 37 for Circuit Boards Location. • See page 38 for Note.
1
3
2
4
KEY-CON BOARD
A
B
A
TO
MAIN BOARD
CN104
(Page 52)
11
1-664-229-
(11)
C
16
— 77 —
— 78 —
HCD-XB66K
7-30.
WAVEFORMS
7-31.
IC BLOCK DIAGRAMS
– MAIN SECTION (1/3) –
– CD SECTION (1/2) –
– BD SECTION –
CP
CB
CC1
CC2
FOK
37
RF_I
38
RF_O
39
RF_M
4.3Vp-p
RFTC
CXA1992AR
LD
IC101
(PLAY MODE)
PD
1 IC301 !¡ (X1)
PD1
5 IC103 ^º (XPCK)
PD2
1 IC101 #£ (RF_O)
36
35
34
33
32
31
30
29
28
27
VEE
200 nsec
PD2 IV
AMP
PD1 IV
AMP
(PLAY MODE)
–
+
VCC
135.5 µsec
LASER POWER CONTROL
F IV AMP
VCC
–
+
–
+
VCC
125 nsec
TEI 47
–
+
ATSC 48
–
+
TZC 49
MIRR
TGFL
FOH
FOL
TGH
TGL
BALH
BALL
ATSC
10Vp-p
59.8 nsec
MIRR
LPC
LDON
+
–
E-F BALANCE
WINDOW COMP.
IIL
↓
TTL
TTL
↓
IIL
FOK
TRK. GAIN
WINDOW COMP.
LPCL
IFB5
IFB6
IFB4
IFB3
IFB2
IFB1
TGFL
BAL3
BAL4
BAL1
BAL2
TOG3
TOG2
TOG1
TOG4
+
–
+
–
+
–
+
–
LPFI 46
23 XRST
VEE
+
–
+
–
VEE
LEVEL S
22 DATA
FO. BIAS
WINDOW
COMP.
–
+
3.6Vp-p
IIL DATA REGISTER
INPUT SHIFT REGISTER
ADDRESS DECODER
SENS SELECTOR
OUTPUT DECODER
19 LOCK
TZC
FZC
DFCTO
IFB1-6
BAL1-4
TOG1-4
–
+
DFCT
FS1-4
TG1-2
TM1-7
PS1-4
ISET
VCC
VCC
TM4
–
+
TM6
15 SL_M
VCC
FOCUS
PHASE COMPENSATION
TM7
FS1
TM5
TM3
+
–
+
–
VEE
DFCT
VEE
FS2
–
+
FZC 52
TG1
VCC
16 SL_O
TRACKING
PHASE COMPENSATION
VEE
VCC
Charge
up
FZC COMP.
FSET
TG2
+
–
FS4
6
FEI
FDFCT
FGD
FLB
FE_O
7
8
9
10
11
12
13
TA_O
5
TA_M
4
FSET
3
TG2
2
TGU
1
FEO
VEE
— 79 —
17 ISET
TM1
TDFCT 50
VC 51
18 VCC
VCC
ATSC
WINDOW
COMP.
TZC COMP.
21 XLT
20 CLK
SRCH
2.4Vp-p
VEE
TEO 45
+
–
7.8 µsec
+
–
+
–
1 IC601 !£ (X-IN)
8 IC103 *ª (XTAI)
VEE
+
–
VEE 44
DFCT
–
+
– PANEL SECTION (1/3) –
24 C. OUT
VEE
+
–
+
–
5.6Vp-p
135.5 µsec
4 IC103 @¶ (MDP)
VCC
FE AMP
E IV AMP
EI 43
25 SENS1
–
+
VCC
–
+
(PLAY MODE)
Approx. 0.2Vp-p
–
+
–
+
E 42
–
+
3 IC101 $¶ (TEI)
–
+
30.4 µsec
7 IC103 &¢ (WFCK)
IIL
↓
TTL
VEE
F 41
CC1
2.4Vp-p
+
–
–
+
APC
5.6Vp-p
26 SENS2
+
–
FE_BIAS 40
Approx. 0.1Vp-p
–
+
2 IC301 !¢ (XT1)
–
+
6 IC103 ^™ (RFCK)
–
+
–
+
2 IC101 2 (FEI)
–
+
RF SUMMING
AMP
DFCT1
7 Vp-p
FE_M
230 nsec
+
–
Approx. 1.3Vp-p
— 80 —
14 SL_P
TM2
OP IN (+)
GND
23
22
21
20
NC
OUT4B
OP IN (–)
24
OUT4A
OP OUT
25
OUT3B
IN3A
26
OUT3A
IN3B
27
VCC
IN4A
28
NC
IN4B
IC102 BA5941FP-E2
19
18
17
16
15
– +
+ –
+ –
+
–
LEVEL SHIFT
+
–
LEVEL SHIFT
+
–
LEVEL SHIFT
+
–
– +
+ –
11
12
13
14
OUT1B
10
+ –
VCC
OUT2B
9
– +
OUT2A
Vcc
MUTE
GND
IN1B
8
7
GND
BIAS IN
6
5
IN2A
VCC
LRCKI
PCMD
PCMDI
BCK
BCKI
VSS
VDD
GTOP
XUGF
XPCK
GFS
RFCK
C2PO
XROF
MNT3
MNT1
MNT0
XTSL
FSTT
C4M
DOUT
EMPH
EMPHI
WFCK
SCOR
SBSO
EXCK
VSS
VDD
CXD2591Q
SYSM
IC103
4
IN2B
3
IN1A
2
MUTE
OUT1A
LEVEL SHIFT
Vcc
1
+ –
+ –
Vcc
80 79 78 77 76 75 74 73 72 71 70 69 68 67 66 65 64 63 62 61 60 59 58 57 56 55 54 53 52 51
50 LRCK
NC 81
AVSS 82
49 WDCK
AVDD 83
48 ASYE
AOUT1 84
47 ASYO
–
+
LOUT1 86
AVSS 87
XVDD 88
XTAI 89
XTAO 90
–
+
XVSS 91
AVSS 92
PWM
–
+
ASYMMETRY
CORRECTOR
3RD-ORDER NOISE SHAPER
–
+
PWM
AIN1 85
45 BIAS
44 RF
ERROR
CORRECTOR
43 AVDD
D/A
INTERFACE
EFM
DEMODURATOR
42 CLTV
DIGITAL
PLL
41 AVSS
40 FILI
39 FILO
DIGITAL OUT
16K RAM
LOUT2 93
38 PCO
AIN2 94
OSC
AOUT2 95
37 VCTL
36 V16M
AVDD 96
SERIAL-IN
INTERFACE
AVSS 97
35 VCKI
SUB CODE
PROCESSOR
OVER SAMPLING
DIGITAL FILTER
CLOCK
GENERATOR
NC 98
34 VPCO1
33 VPCO2
INVERTER
COMPARATER
SW R1 GND
3
4
SW P1 CONT
5
6
GND
VCC
7
8
SW P2 GND
9
SW R2
– 81 –
31 TES0
PWMI
LOCK
MDS
MDP
MON
VSS
FOK
VDD
XLON
SPOC
SPOD
SPOB
CLKO
SPOA
XLTO
CNIN
DATO
SENS
– AUDIO SECTION –
IC602 µPC1330HA
2
DIGITAL CLV
10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30
SEIN
9
XLAT
8
CLOK
7
DATA
6
SQSO
5
SQCK
4
TES2
VSS
3
32 TES1
SERVO
AUTO
SEQUENCER
CPU
INTERFACE
CKOUT
2
LMUT
1
VDD
XRST 100
RMUT
TIMING
LOGIC
NC 99
1
46 ASYI
– CD MOTOR SECTION –
IC201
TA8409S
VREF
BLOCK
STANDBY
BLOCK
HEAT
CUT OFF
BLOCK
2
VCC
1
IN2
3
OUT2
5
GND
4
NC
6
VS
8
VREF
7
OUT1
9
IN1
– MAIN SECTION –
IC281
IC1502
µPC1237HA
LB1641
T.S.D
OVER LOAD DET
O.C.P
MOTOR
DRIVE
VCC ON
MUTE
F/F
OFFSET DET
MOTOR
DRIVE
LATCH/
AUTORESET
FWD/REV/STOP
CONTROL LOGIC
MOTOR
DRIVE
8
10
9
NOISE
FILTER
7
8
VCC 2
6
7
REV.IN
5
6
FWD.IN
4
5
4
NOISE
FILTER
3
MOTOR
DRIVE
2
GND
1
3
CLAMP
2
1
VCC
VCC 1
AC OFF
DET
– KEY-CON SECTION –
IC501
M65847FP-TP
ON/OFF
VREF
~_1.8V
15 MIXOUT
16 MIXIN
17 LPF2OUT
18 LPF2IN
19 HPFOUT
21 LPF1OUT
22 LPF1IN
23 ADINTIN
24 ADINTOUT
25 DAIINTIN
20 HPFIN
HPF
REF
–
LPF2
REF
MIX
REF
CLOCK
GENERATOR
RAM
D/A
–
+
LPF1
REF
OVER HEAT
PROTECT
RESET
ERROR
AMP
–
+
VREF VCC
–
A/D
VREF
+
VCC
START
CIRCUIT
+
VMUTE
ON/OFF
26 DAIINTOUT
CURRENT
LIMITER
27 MODE1
CURRENT
LIMITER
28 MODE2
LA5617
~_140uA
COMPARATER
IC901
REF
LOGIC
GND
NC
CN2
VEE
VO2
5
6
7
8
9
10
11
12
13
14
VCC
EN DISPLAY
4
GND
EN
3
REF
CN1
2
KEY5
VCC
1
KEY4
10
STROBE/KEY3
9
SCK/KEY2
8
SDATA/KEY1
7
CLKO/KEY0
6
KEY UP
5
KEY DOWN
4
DA2CONT
3
DA1CONT
2
ADCONT
1
VO1
ERROR
AMP
– 82 –
SECTION 8
EXPLODED VIEWS
NOTE:
• -XX, -X mean standardized parts, so they may
have some differences from the original one.
• Items marked “*” are not stocked since they
are seldom required for routine service. Some
delay should be anticipated when ordering these
items.
•
•
The mechanical parts with no reference number
in the exploded views are not supplied.
Hardware (# mark) list and accessories and
packing materials are given in the last of this
parts list.
The components identified by mark ! or
dotted line with mark ! are critical for safety.
Replace only with part number specified.
• Abbreviation
IA : Indonesian
TH : Thai
8-1. CASE, REAR PANEL SECTION
2
#2
#2
3
#1
1
#3
#1
#2
#1
1
#1
M100
6
5
#1
Ref. No.
*
*
*
*
1
2
3
3
3
Part No.
Description
3-363-099-01
4-987-052-91
4-996-413-11
4-996-413-61
4-996-413-71
SCREW (CASE 3 TP2)
CASE
PANEL, BACK (SP, MY)
PANEL, BACK (E, IA)
PANEL, BACK (EA)
Remarks
Ref. No.
Part No.
* 3
5
4-996-413-91 PANEL, BACK (TH)
1-233-545-11 ENCAPSULATED COMPONENT
(FM/AM TUNER UNIT)
1-769-974-11 WIRE (FLAT TYPE) (13 CORE)
1-763-072-11 FAN, D.C.
6
M100
— 83 —
Description
Remarks
8-2. FRONT PANEL SECTION-1
58
57
72
59
TCM-220WR2
61
57
57
57
62
60
57
#1
not
supplied
55
77
56
62
78
75
76
57
63
64
54
65
57
66
57
78
53
57
not
supplied
74
69
67
73
supplied
with S711
57
70
52
68
51
71
57
Ref. No.
Part No.
Description
Ref. No.
Part No.
Description
51
52
* 53
54
* 55
4-987-995-01
4-987-001-11
1-664-019-11
X-4949-282-1
1-664-012-11
SPRING (CD EJECT), COMPRESSION
BUTTON (EJECT CD)
CD-A SW BOARD
PANEL (A) SUB ASSY
TC-A SW BOARD
Remarks
65
* 66
* 67
68
69
4-987-000-11
1-664-013-11
1-664-020-11
X-4949-279-1
4-987-037-11
BUTTON (EJECT B)
TC-B SW BOARD
CD-B1 SW BOARD
BUTTON (CD STOP) ASSY
KNOB (JOG)
56
57
58
59
60
4-986-999-12
4-951-620-01
1-773-161-11
1-769-949-11
3-354-963-01
BUTTON (EJECT A)
SCREW (2.6 × 8), +BVTP
WIRE (FLAT TYPE) (21 CORE)
WIRE (FLAT TYPE) (11 CORE)
DAMPER
70
* 71
72
72
73
X-4949-274-1
1-664-021-11
A-4384-916-A
A-4411-134-A
4-987-014-01
PANEL (B) SUB ASSY
CD-B2 SW BOARD
LID ASSY, CD
LID ASSY, CD
INDICATOR (CD)
* 61
62
* 63
* 64
1-664-017-11
4-957-577-01
1-664-016-11
4-987-933-01
LED BOARD
SCREW PTP WH (2.6 × 8) (DIA. 10)
DOOR SW BOARD
BRACKET (TA)
74
75
76
77
78
4-987-002-11
X-4949-685-1
4-987-997-01
4-987-998-01
3-568-749-00
BUTTON (CD.PLAY)
LID ASSY, DISC
SPRING (CD. LID), TORSION
SPRING (LOCK SHAFT), TORSION
CUSHION, ECM
— 84 —
Remarks
8-3. FRONT PANEL SECTION-2
110
109
supplied with
J761
109
not
supplied
supplied with
J762
supplied with
RV760
108
102
supplied with
J760
supplied with
RV761
113
112
109
111
114
115
116
116
not
supplied
supplied with
S701
109
not
supplied
107
101
106
105
Ref. No.
Part No.
Description
101
102
105
106
107
X-4949-293-1
4-973-644-71
4-948-236-21
X-4949-271-1
4-987-036-11
PANEL ASSY
KNOB (ECHO)
CUSHION (107)
LID ASSY, CASSETTE
KNOB (VOL)
108
109
4-973-644-71 KNOB (MIC)
4-951-620-01 SCREW (2.6 × 8), +BVTP
Remarks
Ref. No.
Part No.
Description
* 110
111
112
* 113
* 114
A-4403-916-A
4-986-990-11
4-978-683-01
4-987-041-01
A-4403-858-A
HEADPHONE/MIC BOARD, COMPLETE
BUTTON (CURSOR)
SPRING, COMPRESSION
COVER, CURSOR
PANEL BOARD, COMPLETE
115
116
— 85 —
1-773-051-11 WIRE (FLAT TYPE) (17 CORE)
4-987-996-01 SPRING (TC LID), TENSION
Remarks
8-4. CHASSIS SECTION
#13
151
not supplied
#1
not supplied
T901
#1
#2
153
#1
154
not supplied
152
#4
160
#1
not
supplied
155
CDM37LH-5BD29AL
E, IA, TH
#1
#1
158
#1
CNP901
E,SP,MY
#1
158
156
CNP901
not supplied
157
not supplied
#1
Ref. No.
Part No.
Description
Remarks
151
152
152
152
* 153
1-668-169-11
3-703-244-00
3-703-571-11
4-966-266-01
A-4403-848-A
TRANS BOARD
BUSHING (FBS001), CORD (EA, SP, MY)
BUSHING (S) (4516), CORD (TH)
BUSHING (S) (FBS002), CORD (E, IA)
POWER AMP BOARD, COMPLETE (EXCEPT TH)
* 153
* 154
* 155
A-4414-461-A POWER AMP BOARD, COMPLETE (TH)
4-988-533-01 HOLDER, PWB
A-4403-855-A MAIN BOARD, COMPLETE
Ref. No.
Part No.
Description
! 156
157
! 158
! 158
* 160
1-777-868-11
X-4941-228-1
1-569-007-11
1-569-008-11
A-4403-922-A
WIRE (FLAT TYPE) (19 CORE)
FOOT (F22125H-M)
ADAPTOR, CONVERSION 2P (E, IA, TH)
ADAPTOR, CONVERSION 2P (EA, SP, MY)
KEY-CON BOARD, COMPLETE
! CNP901
! CNP901
! CNP901
! T901
1-558-943-41
1-558-943-51
1-575-651-21
1-431-638-11
CORD, POWER (TH)
CORD, POWER (E, IA)
CORD, POWER (EA, SP, MY)
TRANSFORMER, POWER
— 86 —
Remarks
The components identified by mark ! or dotted
line with mark ! are critical for safety.
Replace only with part number specified.
8-5. TAPE MECHANISM DECK SECTION-1
(TCM-220WR2)
208
201
202
209
206
210
#5
#5
207
#5
206
208
204
not supplied
203
205
#2
Ref. No.
201
202
203
204
205
Part No.
Description
4-959-229-11
X-4947-943-1
X-4947-944-1
4-959-231-11
4-959-232-11
DETENT, CASSETTE
HOLDER (L) ASSY, CASSETTE
HOLDER (R) ASSY, CASSETTE
SPRING (L), TORSION
SPRING (R), TORSION
Remarks
Ref. No.
Part No.
Description
206
* 207
208
209
210
3-354-963-01
4-980-439-01
3-354-957-01
3-354-953-01
3-354-954-01
DAMPER
FULCRUM, HOLDER
JOINT (LOCK LEVER)
LEVER (LOCK LEVER L)
LEVER (LOCK LEVER R)
— 87 —
Remarks
8-6. TAPE MECHANISM DECK SECTION-2
(TCM-220WR2)
#6
270
including rC

rC refer to next page. 
269
273
rA
#6
265
271
264
not supplied
272
HP101
(including rA)
266
262
rB
rA
257
263
269
261
256
265
264
258
272
267
260
259
255
not supplied
268
HRPE101
(including rB)
254
not supplied
253
rB
269
266
not supplied
262
257
263
261
259
256
not supplied
255
252
258
#7
260
251
not supplied
252
Ref. No.
254
#7
251
Part No.
Description
251
252
253
254
255
3-908-560-01
3-919-684-01
X-3373-113-1
3-908-556-01
3-908-558-02
SPRING, AZIMUTH ADJUSTMENT
SCREW, AZIMUTH ADJUSTMENT
SLIDER (HEAD) ASSY
SPRING, HEAD TOGGLE
FITTING BLOCK, HEAD
256
* 257
258
259
260
3-908-557-02
3-908-559-01
3-908-555-01
3-917-143-11
3-388-848-01
ROTARY BLOCK, HEAD
STOPPER, AZIMUTH
SLIDER (REV SLIDER)
SPRING, TENSION
SCREW (P2X6) (B TIGHT)
261
262
253
not supplied
3-939-371-01 SPRING (1), TENSION
X-3369-909-1 PINCH LEVER (REV) ASSY
Remarks
Ref. No.
Part No.
Description
263
264
265
266
267
X-3369-908-1
3-908-613-01
3-917-141-01
X-3371-305-1
3-669-465-01
PINCH LEVER (FWD) ASSY
GEAR (S), REEL
SPRING, COMPRESSION
REEL (T) ASSY
WASHER (1.5), STOPPER
268
269
* 270
271
272
X-3370-173-1
3-939-862-01
A-2007-131-A
3-930-972-01
3-917-142-01
TU ASSY
CLIP
AUDIO BOARD, COMPLETE
DETENT, HALF
SPRING, COMPRESSION
273
3-938-863-01 STOPPER
HP101 1-500-093-11 HEAD, MAGNETIC (PLAYBACK)
HRPE101 1-500-094-11 HEAD, MAGNETIC (REC/PB/ERASE)
— 88 —
Remarks
8-7. TAPE MECHANISM DECK SECTION-3
(TCM-220WR2)
rC: MOTOR board (supplied with AUDIO board)
rC
(refer to front page.)
M2
318
319
#10
317
320
#11
310
321
#10
302
311
321
309
316
310
#7
325
313
315
308
323
306
307
319
305
312
322
304
307
314
#8
313
303
#9
301
#9
M1
Ref. No.
Part No.
Description
301
302
303
304
305
3-908-597-01
3-908-608-11
X-3372-930-1
X-3370-882-1
3-928-047-01
CAM (A)
SCREW, STEP
ARM (A) ASSY, FR
FLYWHEEL (AR) ASSY
PULLEY, TENSION
306
307
308
309
310
3-908-599-01
3-908-601-01
3-908-603-01
X-3367-108-1
3-908-605-01
LEVER (REV-A)
SPRING (REV LEVER), TORSION
LEVER (TRIGGER A)
FLYWHEEL (BF) ASSY
SPRING (TRIGGER), TORSION
311
312
313
3-908-609-01 GEAR, TRIGGER
3-913-845-11 BELT (A)
3-913-846-11 BELT (FR)
302
not supplied
Remarks
Ref. No.
Part No.
Description
314
315
* 316
317
318
X-3370-171-1
3-908-600-01
1-650-669-11
3-908-598-01
X-3372-931-1
FLYWHEEL (BR) ASSY
LEVER (REV-B)
LEAF SWITCH BOARD
CAM (B)
ARM (B) ASSY, FR
319
320
321
322
323
3-914-111-01
3-908-604-01
3-911-115-01
3-917-176-11
X-3370-172-1
SPRING (FR), TORSION
LEVER (TRIGGER B)
WASHER, STOPPER
BELT (B)
FLYWHEEL (AF) ASSY
325
M1
M2
X-3371-441-1 CHASSIS ASSY, MECHANICAL
X-3371-223-1 MOTOR ASSY, CAPSTAN
A-2004-410-A MOTOR ASSY, DC (TRIGGER)
— 89 —
Remarks
8-8. CD MECHANISM DECK SECTION
(CDM37LH-5BD29AL)
351
351
355
352
351
358
356
#1
353
not supplied
354
359
360
357
#1
361
360
359
359
360
373
375
362
372
374
352
368
368
M201
376
368
367
BU-5BD29AL
369
not
supplied
369
363
365
#1
361
370
#1
#1
#1
366
364
371
Ref. No.
*
*
*
*
Part No.
Description
351
352
353
354
355
4-987-976-01
4-944-490-01
A-4660-978-A
4-978-421-01
4-978-425-01
356
357
358
359
360
361
362
363
364
Remarks
Ref. No.
Part No.
Description
SCREW, STEP
BELT (TIMING)
GEAR (PULLEY) ASSY
GEAR (MID)
ROLLER (CAM)
365
* 366
* 367
368
369
4-978-426-01
1-659-059-13
1-659-058-13
4-985-672-01
4-958-593-01
INDICATOR (NO.)
BD LED BOARD
TABLE SENSOR BOARD
SCREW (+PTPWH M2.6), FLOATING
SPRING (BU), COMPRESSION
4-978-420-01
1-452-925-21
4-978-417-01
4-934-376-01
X-4947-960-1
CAM (HOLDER)
MAGNET ASSY
TABLE, DISC
SHAFT (ROLLER)
ROLLER ASSY
* 370
371
372
373
374
4-978-419-01
4-998-716-01
4-989-493-01
4-989-494-01
4-989-819-02
HOLDER (BU-5)
SCREW, BU FITTING
SLIDER (37)
SCREW (SLIDER), STEP
SPRING, TENSION
4-978-583-01
4-978-418-01
4-980-385-01
A-4673-765-A
BRACKET (BU)
CHASSIS
HOLDER (SW)
CD MOTOR BOARD, COMPLETE
375
376
M201
— 90 —
4-989-491-21 COVER, LENS
4-993-142-11 PULLEY (L), PRESS
A-4660-977-A MOTOR ASSY (TABLE)
Remarks
8-9. BASE UNIT SECTION
(BU-5BD29AL)
401
402
#12
403
405
M101
404
M102
404
406
407
408
Ref. No.
Part No.
Description
! 401
402
403
404
405
8-820-020-01
1-769-069-11
4-917-567-21
4-951-940-01
4-917-565-01
OPTICAL PICK-UP KSS-213D/Q-NP
WIRE (FLAT TYPE) (16 CORE)
GEAR (M)
INSULATOR (BU)
SHAFT, SLED
Remarks
Ref. No.
Part No.
Description
406
* 407
408
M101
M102
4-917-564-01
A-4699-522-A
4-951-620-01
X-4917-504-1
X-4917-523-4
GEAR (P), FLATNESS
BD BOARD, COMPLETE
SCREW (2.6X8), +BVTP
MOTOR ASSY (SPINDLE)
MOTOR ASSY (SLED)
— 91 —
Remarks
The components identified by mark ! or dotted
line with mark ! are critical for safety.
Replace only with part number specified.
SECTION 9
ELECTRICAL PARTS LIST
AUDIO
NOTE:
When indicating parts by reference number,
please include the board name.
The components identified by mark ! or
dotted line with mark ! are critical for safety.
Replace only with part number specified.
•
•
•
• Abbreviation
IA : Indonesian
TH : Thai
•
Due to standardization, replacements in the
parts list may be different from the parts
specified in the diagrams or the components
used on the set.
-XX, -X mean standardized parts, so they may
have some difference from the original one.
Items marked “*” are not stocked since they
are seldom required for routine service. Some
delay should be anticipated when ordering these
items.
CAPACITORS:
uF: µF
Ref. No.
Part No.
*
A-2007-131-A AUDIO BOARD, COMPLETE
**********************
(including MOTOR BOARD)
Description
Remarks
< CAPACITOR >
C301
C302
C303
C304
C305
1-162-289-31
1-126-968-11
1-162-282-31
1-130-483-00
1-107-715-11
CERAMIC
ELECT
CERAMIC
MYLAR
ELECT
390PF
100uF
100PF
0.01uF
22uF
10%
20%
10%
5%
20%
50V
6.3V
50V
50V
16V
C311
C313
C314
C315
C331
1-162-289-31
1-162-282-31
1-130-487-00
1-126-233-11
1-137-427-11
CERAMIC
CERAMIC
MYLAR
ELECT
FILM
390PF
100PF
0.022uF
22uF
120PF
10%
10%
5%
20%
5%
50V
50V
50V
50V
50V
C332
C333
C401
C402
C403
1-162-288-31
1-162-209-31
1-162-289-31
1-126-968-11
1-162-282-31
CERAMIC
CERAMIC
CERAMIC
ELECT
CERAMIC
330PF
27PF
390PF
100uF
100PF
10%
5%
10%
20%
10%
50V
50V
50V
6.3V
50V
C404
C405
C411
C413
C414
1-130-483-00
1-107-715-11
1-162-289-31
1-162-282-31
1-130-487-00
MYLAR
ELECT
CERAMIC
CERAMIC
MYLAR
0.01uF
22uF
390PF
100PF
0.022uF
5%
20%
10%
10%
5%
50V
16V
50V
50V
50V
C415
C431
C432
C433
C601
1-126-233-11
1-137-427-11
1-162-288-31
1-162-209-31
1-104-396-11
ELECT
FILM
CERAMIC
CERAMIC
ELECT
22uF
120PF
330PF
27PF
10uF
20%
5%
10%
5%
20%
50V
50V
50V
50V
16V
C602
C611
C612
C621
C622
1-104-396-11
1-124-907-11
1-124-907-11
1-137-150-11
1-126-961-11
ELECT
ELECT
ELECT
FILM
ELECT
10uF
10uF
10uF
0.01uF
2.2uF
20%
20%
20%
5%
20%
16V
50V
50V
100V
50V
C623
C624
C625
C627
C628
1-136-155-00
1-130-481-00
1-130-481-00
1-124-903-11
1-136-153-00
FILM
MYLAR
MYLAR
ELECT
FILM
0.015uF
0.0068uF
0.0068uF
1uF
0.01uF
5%
5%
5%
20%
5%
50V
50V
50V
50V
50V
C642
C651
1-104-664-11 ELECT
1-161-494-00 CERAMIC
47uF
0.022uF
20%
16V
25V
Ref. No.
Part No.
•
•
•
RESISTORS
All resistors are in ohms.
METAL: metal-film resistor
METAL OXIDE: Metal Oxide-film resistor
F: nonflammable
COILS
uH: µH
SEMICONDUCTORS
In each case, u: µ, for example:
uA...: µA... , uPA... , µPA... ,
uPB... , µPB... , uPC... , µPC... ,
uPD..., µPD...
Description
Remarks
< IC >
IC601 8-759-111-44
IC602 8-759-143-54
IC611 8-759-111-44
IC uPC4570C-1
IC uPC1330HA
IC uPC4570C-1
< COIL >
L331
L431
1-410-780-11 INDUCTOR
1-410-780-11 INDUCTOR
27mH
27mH
< TRANSISTOR >
< CONNECTOR >
CN601 1-695-382-31
CN602 1-564-718-11
* CN651 1-564-521-11
PIN, CONNECTOR (PC BOARD) 21P
PIN, CONNECTOR (SMALL TYPE) 2P
PLUG, CONNECTOR 6P
Q621
Q622
Q623
Q651
8-729-142-46
8-729-142-46
8-729-801-93
8-729-900-65
TRANSISTOR
TRANSISTOR
TRANSISTOR
TRANSISTOR
2SC2001-LK
2SC2001-LK
2SD1387
DTA144ES
< RESISTOR >
R301
R302
R303
R304
R305
1-247-881-00
1-249-409-11
1-249-433-11
1-247-889-00
1-247-858-11
CARBON
CARBON
CARBON
CARBON
CARBON
120K
220
22K
270K
13K
5%
5%
5%
5%
5%
1/4W
1/4W
1/4W
1/4W
1/4W
R311
R312
R314
R315
R331
1-247-881-00
1-247-807-31
1-247-882-11
1-247-850-11
1-249-430-11
CARBON
CARBON
CARBON
CARBON
CARBON
120K
100
130K
6.2K
12K
5%
5%
5%
5%
5%
1/4W
1/4W
1/4W
1/4W
1/4W
R401
R402
R403
R404
R405
1-247-881-00
1-249-409-11
1-249-433-11
1-247-889-00
1-247-858-11
CARBON
CARBON
CARBON
CARBON
CARBON
120K
220
22K
270K
13K
5%
5%
5%
5%
5%
1/4W
1/4W
1/4W
1/4W
1/4W
R411
R412
R414
R415
R431
1-247-881-00
1-247-807-31
1-247-882-11
1-247-850-11
1-249-430-11
CARBON
CARBON
CARBON
CARBON
CARBON
120K
100
130K
6.2K
12K
5%
5%
5%
5%
5%
1/4W
1/4W
1/4W
1/4W
1/4W
R601
R602
R608
R609
R611
1-249-409-11
1-249-409-11
1-249-409-11
1-249-433-11
1-249-409-11
CARBON
CARBON
CARBON
CARBON
CARBON
220
220
220
22K
220
5%
5%
5%
5%
5%
1/4W
1/4W
1/4W
1/4W
1/4W
R612
! R621
! R622
R623
R624
1-249-409-11
1-212-851-00
1-212-851-00
1-249-432-11
1-249-432-11
CARBON
FUSIBLE
FUSIBLE
CARBON
CARBON
220
5.6
5.6
18K
18K
5%
5%
5%
5%
5%
1/4W
1/4W F
1/4W F
1/4W
1/4W
— 92 —
AUDIO
Ref. No.
R625
R651
R652
R653
Part No.
Description
1-249-429-11
1-247-856-00
1-247-856-00
1-249-441-11
CARBON
CARBON
CARBON
CARBON
Remarks
10K
11K
11K
100K
5%
5%
5%
5%
1/4W
1/4W
1/4W
1/4W
< VARIABLE RESISTOR >
RV301
RV311
RV341
RV401
RV411
1-238-598-11
1-238-598-11
1-238-551-11
1-238-598-11
1-238-598-11
RES, ADJ, CARBON 2.2K
RES, ADJ, CARBON 2.2K
RES, ADJ, CARBON 220K
RES, ADJ, CARBON 2.2K
RES, ADJ, CARBON 2.2K
RV441
RV651
RV652
1-238-551-11 RES, ADJ, CARBON 220K
1-238-599-11 RES, ADJ, CARBON 4.7K
1-238-599-11 RES, ADJ, CARBON 4.7K
< TRANSFORMER >
T621
1-423-980-11 TRANSFORMER, BIAS OSCILLATION
************************************************************
A-4699-522-A BD BOARD, COMPLETE
*******************
*
Ref. No.
BD
Part No.
Description
C164
C165
C166
C167
C168
1-163-145-00
1-164-004-11
1-163-137-00
1-163-121-00
1-163-137-00
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
0.0015uF
0.1uF
680PF
150PF
680PF
5%
10%
5%
5%
5%
50V
25V
50V
50V
50V
C169
C170
C171
C173
C174
1-163-121-00
1-163-099-00
1-163-237-11
1-163-038-91
1-163-038-91
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
150PF
18PF
27PF
0.1uF
0.1uF
5%
5%
5%
50V
50V
50V
25V
25V
C175
C176
C177
C178
C179
1-163-038-91
1-163-038-91
1-163-038-91
1-163-038-91
1-163-038-91
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
0.1uF
0.1uF
0.1uF
0.1uF
0.1uF
C181
C182
C183
C185
C188
1-126-205-11
1-126-393-11
1-124-778-00
1-164-232-11
1-163-235-11
ELECT CHIP
ELECT
ELECT CHIP
CERAMIC CHIP
CERAMIC CHIP
47uF
33uF
22uF
0.01uF
22PF
5%
6.3V
10V
6.3V
50V
50V
C189
1-163-235-11 CERAMIC CHIP
22PF
5%
50V
< CAPACITOR >
Remarks
25V
25V
25V
25V
25V
20%
20%
20%
< CONNECTOR >
C101
C102
C103
C105
C106
1-126-607-11
1-163-141-00
1-164-346-11
1-163-038-91
1-164-161-11
ELECT CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
47uF
20%
0.001uF 5%
1uF
0.1uF
0.0022uF 10%
4V
50V
16V
25V
100V
C107
C108
C109
C110
C111
1-164-161-11
1-164-232-11
1-164-232-11
1-163-989-11
1-163-017-00
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
0.0022uF 10%
0.01uF
0.01uF
0.033uF 10%
0.0047uF 5%
100V
50V
50V
25V
50V
C112
C113
C114
C115
C116
1-163-017-00
1-164-161-11
1-164-005-11
1-126-607-11
1-163-016-00
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
ELECT CHIP
CERAMIC CHIP
0.0047uF
0.0022uF
0.47uF
47uF
0.0039uF
50V
100V
25V
4V
50V
C117
C118
C119
C120
C121
1-164-005-11
1-164-004-11
1-163-038-91
1-124-779-00
1-163-038-91
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
ELECT CHIP
CERAMIC CHIP
0.47uF
0.1uF
0.1uF
10uF
0.1uF
C122
C123
C124
C125
C126
1-164-232-11
1-163-038-91
1-126-607-11
1-164-232-11
1-163-038-91
CERAMIC CHIP
CERAMIC CHIP
ELECT CHIP
CERAMIC CHIP
CERAMIC CHIP
0.01uF
0.1uF
47uF
0.01uF
0.1uF
C127
C128
C129
C130
C131
1-164-161-11
1-163-135-00
1-163-038-91
1-164-336-11
1-164-346-11
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
0.0022uF 10%
560PF
5%
0.1uF
0.33uF
1uF
100V
50V
25V
25V
16V
C140
C154
C161
C162
C163
1-110-501-11
1-163-235-11
1-164-005-11
1-164-232-11
1-163-117-00
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
0.33uF
22PF
0.47uF
0.01uF
100PF
16V
50V
25V
50V
50V
5%
10%
20%
10%
10%
20%
25V
25V
25V
16V
25V
CNU101 1-770-014-11 CONNECTOR, FFC/FPC 16P
CNU102 1-778-874-11 CONNECTOR, FFC(LIF(NON-ZIF))19P
< FERRITE BEAD >
FB101
FB103
1-414-234-11 INDUCTOR, FERRITE BEAD
1-414-234-11 INDUCTOR, FERRITE BEAD
< IC >
IC101
IC102
IC103
8-752-080-62 IC CXA1992AR
8-759-429-32 IC BA5941FP-E2
8-752-378-66 IC CXD2519Q
< CHIP CONDUCTOR >
JW101
JW104
1-216-295-91 CONDUCTOR, CHIP (2012)
1-216-295-91 CONDUCTOR, CHIP (2012)
< TRANSISTOR >
Q101
8-729-010-08 TRANSISTOR MSB710-R
< RESISTOR >
20%
10%
5%
5%
50V
25V
4V
50V
25V
R102
R104
R105
R106
R107
1-216-001-00
1-216-093-00
1-216-088-00
1-216-088-00
1-216-088-00
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
10
68K
43K
43K
43K
5%
5%
5%
5%
5%
1/10W
1/10W
1/10W
1/10W
1/10W
R108
R109
R114
R115
R116
1-216-088-00
1-216-093-00
1-216-101-00
1-216-101-00
1-216-061-00
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
43K
68K
150K
150K
3.3K
5%
5%
5%
5%
5%
1/10W
1/10W
1/10W
1/10W
1/10W
R117
R118
R119
R120
R121
1-216-069-00
1-216-063-91
1-216-085-00
1-216-089-91
1-216-114-00
METAL CHIP
METAL GLAZE
METAL CHIP
METAL GLAZE
METAL GLAZE
6.8K
3.9K
33K
47K
510K
5%
5%
5%
5%
5%
1/10W
1/10W
1/10W
1/10W
1/10W
— 93 —
BD
Ref. No.
BD LED
CD MOTOR
CD-A SW
Part No.
Description
Remarks
Ref. No.
Part No.
R122
R123
R124
R125
R126
1-216-097-91
1-216-099-00
1-216-091-00
1-216-069-00
1-216-063-91
METAL GLAZE
METAL CHIP
METAL CHIP
METAL CHIP
METAL GLAZE
100K
120K
56K
6.8K
3.9K
5%
5%
5%
5%
5%
1/10W
1/10W
1/10W
1/10W
1/10W
*
1-659-059-13 BD LED BOARD
*************
Description
*
4-980-385-01 HOLDER (SW)
R127
R128
R129
R130
R131
1-216-089-91
1-216-098-00
1-216-025-91
1-216-079-00
1-216-079-00
METAL GLAZE
METAL CHIP
METAL GLAZE
METAL CHIP
METAL CHIP
47K
110K
100
18K
18K
5%
5%
5%
5%
5%
1/10W
1/10W
1/10W
1/10W
1/10W
R132
R133
R134
R135
R136
1-216-061-00
1-216-061-00
1-216-065-00
1-216-065-00
1-216-073-00
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
3.3K
3.3K
4.7K
4.7K
10K
5%
5%
5%
5%
5%
1/10W
1/10W
1/10W
1/10W
1/10W
R137
R138
R156
R157
R158
1-216-065-00
1-216-025-91
1-216-081-00
1-216-069-00
1-216-001-00
METAL CHIP
METAL GLAZE
METAL CHIP
METAL CHIP
METAL CHIP
4.7K
100
22K
6.8K
10
5%
5%
5%
5%
5%
1/10W
1/10W
1/10W
1/10W
1/10W
R159
R161
R162
R163
R164
1-216-121-91
1-216-097-91
1-216-073-00
1-216-121-91
1-216-061-00
METAL GLAZE
METAL GLAZE
METAL CHIP
METAL GLAZE
METAL CHIP
1M
100K
10K
1M
3.3K
5%
5%
5%
5%
5%
1/10W
1/10W
1/10W
1/10W
1/10W
R165
R166
R167
R168
R169
1-216-049-91
1-216-073-00
1-216-081-00
1-216-073-00
1-216-079-00
METAL GLAZE
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
1K
10K
22K
10K
18K
5%
5%
5%
5%
5%
1/10W
1/10W
1/10W
1/10W
1/10W
R170
R171
R172
R173
R174
1-216-081-00
1-216-073-00
1-216-079-00
1-216-025-91
1-216-033-00
METAL CHIP
METAL CHIP
METAL CHIP
METAL GLAZE
METAL CHIP
22K
10K
18K
100
220
5%
5%
5%
5%
5%
1/10W
1/10W
1/10W
1/10W
1/10W
R175
R176
R177
R178
R179
1-216-025-91
1-216-025-91
1-216-025-91
1-216-025-91
1-216-025-91
METAL GLAZE
METAL GLAZE
METAL GLAZE
METAL GLAZE
METAL GLAZE
100
100
100
100
100
5%
5%
5%
5%
5%
1/10W
1/10W
1/10W
1/10W
1/10W
R180
R181
R188
R190
R191
1-216-025-91
1-216-025-91
1-216-037-00
1-216-097-91
1-216-105-91
METAL GLAZE
METAL GLAZE
METAL CHIP
METAL GLAZE
METAL GLAZE
100
100
330
100K
220K
5%
5%
5%
5%
5%
1/10W
1/10W
1/10W
1/10W
1/10W
Remarks
< DIODE >
D201
8-719-032-98 DIODE SEL5820A (DISC No.)
< TRANSISTOR >
Q201
8-729-119-78 TRANSISTOR 2SC403SP-51
< RESISTOR >
R201
1-247-863-91 CARBON
22K
5%
1/4W
R202
1-249-411-11 CARBON
330
5%
1/4W
R203
1-249-437-11 CARBON
47K
5%
1/4W
************************************************************
A-4673-765-A CD MOTOR BOARD, COMPLETE
*************************
*
< CAPACITOR >
C201
C202
C203
1-124-907-11 ELECT
1-164-159-21 CERAMIC
1-124-907-11 ELECT
10uF
0.1uF
10uF
20%
20%
50V
50V
50V
5%
5%
1/4W
1/4W
< CONNECTOR >
* CN201
1-568-947-11 PIN, CONNECTOR 9P
< IC >
IC201
8-759-365-94 IC TA8409S
< COIL >
L201
1-408-117-00 INDUCTOR 10uH
< RESISTOR >
R205
R206
1-249-427-11 CARBON
1-249-425-11 CARBON
< SWITCH >
S201
1-762-587-11 SWITCH, PUSH (1 KEY) (UP)
************************************************************
1-664-019-11 CD-A SW BOARD
**************
*
< SWITCH >
S101
6.8K
4.7K
< DIODE >
1-572-085-11 SWITCH, LEAF (LIMIT)
D641
8-719-058-04 DIODE SEL5223S-TP15 (NON-STOP)
< VIBRATOR >
< RESISTOR >
X101
1-767-408-21 VIBRATOR, CRYSTAL (16.9344MHz)
************************************************************
R731
R732
R733
R734
R735
1-249-411-11
1-249-413-11
1-249-415-11
1-249-417-11
1-249-419-11
CARBON
CARBON
CARBON
CARBON
CARBON
330
470
680
1K
1.5K
5%
5%
5%
5%
5%
1/4W
1/4W
1/4W
1/4W
1/4W
R736
R737
R741
1-249-421-11 CARBON
1-249-417-11 CARBON
1-247-807-31 CARBON
2.2K
1K
100
5%
5%
5%
1/4W
1/4W
1/4W
— 94 —
CD-A SW
Ref. No.
Part No.
CD-B1 SW
Description
CD-B2 SW
Remarks
< SWITCH >
S661
S662
S663
S664
S665
1-554-303-21
1-554-303-21
1-554-303-21
1-554-303-21
1-554-303-21
DOOR SW
HEADPHONE-MIC
Ref. No.
Part No.
*
1-664-016-11 DOOR SW BOARD
***************
SWITCH, TACTILE (DISC 1)
SWITCH, TACTILE (DISC 2)
SWITCH, TACTILE (DISC 3)
SWITCH, TACTILE (DISC 4)
SWITCH, TACTILE (DISC 5)
Description
Remarks
< CAPACITOR >
C691
1-164-159-21 CERAMIC
0.1uF
50V
< CONNECTOR >
S666
1-554-303-21 SWITCH, TACTILE (FLASH)
S667
1-554-303-21 SWITCH, TACTILE (NON-STOP)
S668
1-554-303-21 SWITCH, TACTILE (LOOP)
************************************************************
1-664-020-11 CD-B1 SW BOARD
***************
*
1-506-481-11 PIN, CONNECTOR 2P
< SWITCH >
S691
1-771-057-11 SWITCH, PUSH (1 KEY)(6 OPEN)
************************************************************
< CONNECTOR >
* CN642
CN661
A-4403-916-A HEADPHONE-MIC BOARD, COMPLETE
*******************************
*
1-568-943-11 PIN, CONNECTOR 5P
< CAPACITOR >
< DIODE >
D645
D646
D647
8-719-057-29 DIODE SML78423C-TP15 (·)
8-719-057-97 DIODE SEL5923A-TP15 (P)
8-719-057-29 DIODE SML78423C-TP15 (·)
C760
C761
C762
C763
C764
1-162-306-11
1-126-961-11
1-162-306-11
1-126-961-11
1-162-294-31
CERAMIC
ELECT
CERAMIC
ELECT
CERAMIC
0.01uF
2.2uF
0.01uF
2.2uF
0.001uF
20%
20%
20%
20%
10%
16V
50V
16V
50V
50V
C765
C766
C767
C768
C769
1-162-215-31
1-162-290-31
1-162-215-31
1-126-961-11
1-162-282-31
CERAMIC
CERAMIC
CERAMIC
ELECT
CERAMIC
47PF
470PF
47PF
2.2uF
100PF
5%
10%
5%
20%
10%
50V
50V
50V
50V
50V
C770
C771
C773
C774
C775
1-126-961-11
1-126-959-11
1-126-964-11
1-126-964-11
1-162-294-31
ELECT
ELECT
ELECT
ELECT
CERAMIC
2.2uF
0.47uF
10uF
10uF
0.001uF
20%
20%
20%
20%
10%
50V
50V
50V
50V
50V
C776
C777
C778
C779
C780
1-162-294-31
1-126-960-11
1-162-305-11
1-162-294-31
1-136-495-11
CERAMIC
ELECT
CERAMIC
CERAMIC
FILM
0.001uF
1uF
0.0068uF
0.001uF
0.068uF
10%
20%
30%
10%
5%
50V
50V
16V
50V
50V
C781
C782
C783
C784
C785
1-126-957-11
1-126-957-11
1-126-967-11
1-136-495-11
1-162-305-11
ELECT
ELECT
ELECT
FILM
CERAMIC
0.22uF
0.22uF
47uF
0.068uF
0.0068uF
20%
20%
20%
5%
30%
50V
50V
10V
50V
16V
C786
C787
C788
C789
C790
1-162-294-31
1-124-250-11
1-126-960-11
1-161-494-00
1-126-967-11
CERAMIC
ELECT
ELECT
CERAMIC
ELECT
0.001uF
0.15uF
1uF
0.022uF
47uF
10%
20%
20%
20%
50V
50V
50V
25V
10V
C791
C794
C795
C797
C798
1-164-159-21
1-164-159-21
1-164-159-21
1-162-302-11
1-164-159-21
CERAMIC
CERAMIC
CERAMIC
CERAMIC
CERAMIC
0.1uF
0.1uF
0.1uF
0.0022uF 20%
0.1uF
50V
50V
50V
16V
50V
C799
1-164-159-21 CERAMIC
0.1uF
50V
< RESISTOR >
R745
R746
R747
R748
R749
1-247-815-91
1-249-411-11
1-249-413-11
1-249-415-11
1-247-807-31
CARBON
CARBON
CARBON
CARBON
CARBON
220
330
470
680
100
5%
5%
5%
5%
5%
1/4W
1/4W
1/4W
1/4W
1/4W
R750
R751
1-247-807-31 CARBON
1-247-807-31 CARBON
100
100
5%
5%
1/4W
1/4W
< SWITCH >
S676
1-554-303-21 SWITCH, TACTILE (·)
S677
1-554-303-21 SWITCH, TACTILE (p)
S678
1-554-303-21 SWITCH, TACTILE (P)
S679
1-554-303-21 SWITCH, TACTILE (DISC SKIP)
************************************************************
1-664-021-11 CD-B2 SW BOARD
***************
*
< RESISTOR >
R752
R753
R754
R755
R756
1-249-417-11
1-249-419-11
1-249-421-11
1-247-843-11
1-249-427-11
CARBON
CARBON
CARBON
CARBON
CARBON
1K
1.5K
2.2K
3.3K
6.8K
5%
5%
5%
5%
5%
1/4W
1/4W
1/4W
1/4W
1/4W
< SWITCH >
S681
S682
S683
S684
S685
1-554-303-21
1-554-303-21
1-554-303-21
1-554-303-21
1-554-303-21
SWITCH, TACTILE ())
SWITCH, TACTILE (REPEAT)
SWITCH, TACTILE (PLAY MODE)
SWITCH, TACTILE (1/ALL DISCS)
SWITCH, TACTILE (EDIT)
S686
1-554-303-21 SWITCH, TACTILE (0)
S711
1-467-968-11 ENCODER, ROTARY (≠ AMS ±)
************************************************************
— 95 —
HEADPHONE-MIC
Ref. No.
Part No.
KEY-CON
Description
Remarks
< CONNECTOR >
* CN701
1-568-935-11 PIN, CONNECTOR 8P
< DIODE >
D761
D762
D763
8-719-200-82 DIODE 11ES2
8-719-200-82 DIODE 11ES2
8-719-200-82 DIODE 11ES2
< IC >
IC760
IC761
8-759-634-51 IC M5218AP
8-759-450-96 IC M65850P
< JACK >
J760
J761
J762
1-770-226-41 JACK (LARGE TYPE) (PHONES)
1-770-226-41 JACK (LARGE TYPE) (MIC 1)
1-770-226-41 JACK (LARGE TYPE) (MIC 2)
< COIL >
L761
1-410-521-11 INDUCTOR
Ref. No.
Part No.
Description
C506
C507
C508
C509
C510
1-162-286-21
1-162-286-21
1-136-495-11
1-136-495-11
1-136-495-11
CERAMIC
CERAMIC
FILM
FILM
FILM
220PF
220PF
0.068uF
0.068uF
0.068uF
10%
10%
5%
5%
5%
Remarks
50V
50V
50V
50V
50V
C511
C512
C513
C514
C515
1-164-159-21
1-162-284-31
1-136-165-00
1-136-165-00
1-162-294-31
CERAMIC
CERAMIC
FILM
FILM
CERAMIC
0.1uF
150PF
0.1uF
0.1uF
0.001uF
10%
5%
5%
10%
50V
50V
50V
50V
50V
C516
C517
C518
C519
C520
1-162-294-31
1-162-294-31
1-162-306-11
1-162-294-31
1-126-964-11
CERAMIC
CERAMIC
CERAMIC
CERAMIC
ELECT
0.001uF
0.001uF
0.01uF
0.001uF
10uF
10%
10%
20%
10%
20%
50V
50V
16V
50V
50V
C521
C522
C523
C524
C525
1-162-291-31
1-162-600-11
1-162-290-31
1-126-964-11
1-126-964-11
CERAMIC
CERAMIC
CERAMIC
ELECT
ELECT
560PF
0.0047uF
470PF
10uF
10uF
10%
30%
10%
20%
20%
50V
16V
50V
50V
50V
C526
C527
C1439
1-126-964-11 ELECT
1-126-964-11 ELECT
1-126-964-11 ELECT
10uF
10uF
10uF
20%
20%
20%
50V
50V
50V
100uH
< RESISTOR >
R760
R761
R762
R763
R764
1-249-429-11
1-249-417-11
1-249-429-11
1-249-417-11
1-249-441-11
CARBON
CARBON
CARBON
CARBON
CARBON
10K
1K
10K
1K
100K
5%
5%
5%
5%
5%
1/4W
1/4W F
1/4W
1/4W F
1/4W
R765
R766
R767
R768
R769
1-249-417-11
1-249-437-11
1-249-429-11
1-249-431-11
1-247-885-00
CARBON
CARBON
CARBON
CARBON
CARBON
1K
47K
10K
15K
180K
5%
5%
5%
5%
5%
1/4W F
1/4W
1/4W
1/4W
1/4W
R770
R771
R772
R773
R774
1-247-807-31
1-247-863-91
1-247-863-91
1-247-863-91
1-247-881-00
CARBON
CARBON
CARBON
CARBON
CARBON
100
22K
22K
22K
120K
5%
5%
5%
5%
5%
1/4W
1/4W
1/4W
1/4W
1/4W
R775
R776
R777
R778
R779
R782
1-247-863-91
1-247-863-91
1-247-863-91
1-249-437-11
1-249-431-11
1-249-429-11
CARBON
CARBON
CARBON
CARBON
CARBON
CARBON
22K
22K
22K
47K
15K
10K
5%
5%
5%
5%
5%
5%
1/4W
1/4W
1/4W
1/4W
1/4W
1/4W
< CONNECTOR >
CN501
1-566-999-11 PIN, CONNECTOR 13P
< IC >
< VARIABLE RESISTOR >
RV760 1-225-366-11 RES, VAR, CARBON 50K (MIC LEVEL)
RV761 1-225-366-11 RES, VAR, CARBON 50K (ECHO LEVEL)
************************************************************
A-4403-922-A KEY-CON BOARD, COMPLETE
************************
< CAPACITOR >
*
C501
C502
C503
C504
C505
1-126-382-11
1-164-159-21
1-126-967-11
1-164-159-21
1-162-600-11
ELECT
CERAMIC
ELECT
CERAMIC
CERAMIC
100uF
20%
0.1uF
47uF
20%
0.1uF
0.0047uF 30%
6.3V
50V
10V
50V
16V
IC501
IC502
8-759-370-84 IC M65847FP-TP
8-759-140-53 IC UPD4053BC
< COIL >
L501
1-410-521-11 INDUCTOR
100uH
< TRANSISTOR >
Q501
Q501
Q502
Q502
8-729-119-78
8-729-620-05
8-729-029-66
8-729-900-80
TRANSISTOR
TRANSISTOR
TRANSISTOR
TRANSISTOR
2SC403SP-51
2SC2603-EF
DTC114ESA
DTC114ES
< RESISTOR >
R501
R502
R503
R504
R505
R506
1-247-807-31
1-249-429-11
1-247-807-31
1-249-425-11
1-247-903-00
1-249-429-11
CARBON
CARBON
CARBON
CARBON
CARBON
CARBON
100
10K
100
4.7K
1M
10K
5%
5%
5%
5%
5%
5%
1/4W
1/4W
1/4W
1/4W F
1/4W
1/4W
R507
R508
R509
R510
R511
1-249-425-11
1-249-429-11
1-249-434-11
1-249-426-11
1-249-424-11
CARBON
CARBON
CARBON
CARBON
CARBON
4.7K
10K
27K
5.6K
3.9K
5%
5%
5%
5%
5%
1/4W F
1/4W
1/4W
1/4W
1/4W F
R512
R513
R514
R515
R516
1-249-431-11
1-249-429-11
1-247-863-91
1-249-429-11
1-249-441-11
CARBON
CARBON
CARBON
CARBON
CARBON
15K
10K
22K
10K
100K
5%
5%
5%
5%
5%
1/4W
1/4W
1/4W
1/4W
1/4W
— 96 —
KEY-CON
Ref. No.
R517
R518
R519
R520
R521
Part No.
Description
1-247-863-91
1-247-863-91
1-249-441-11
1-249-441-11
1-249-429-11
CARBON
CARBON
CARBON
CARBON
CARBON
22K
22K
100K
100K
10K
5%
5%
5%
5%
5%
LED
Remarks
Ref. No.
Part No.
1/4W
1/4W
1/4W
1/4W
1/4W
*
A-4403-855-A MAIN BOARD, COMPLETE
*********************
*
4-870-539-11 PLATE, GROUND
7-685-646-79 SCREW +BVTP 3 × 8 TYPE2 N-S
R522
1-249-425-11 CARBON
4.7K
5%
1/4W F
R523
1-249-425-11 CARBON
4.7K
5%
1/4W F
R524
1-249-429-11 CARBON
10K
5%
1/4W
R525
1-249-417-11 CARBON
1K
5%
1/4W F
************************************************************
1-650-669-11 LEAF SWITCH BOARD
******************
*
LEAF SWITCH
< CONNECTOR >
* CN1001 1-568-854-11 SOCKET, CONNECTOR 11P
Description
MAIN
Remarks
< CAPACITOR >
C100
C102
C103
C104
C105
1-164-159-21
1-162-282-31
1-162-282-31
1-126-961-11
1-162-600-11
CERAMIC
CERAMIC
CERAMIC
ELECT
CERAMIC
0.1uF
100PF
100PF
2.2uF
0.0047uF
10%
10%
20%
30%
50V
50V
50V
50V
16V
C106
C107
C121
C122
C123
1-162-301-11
1-126-956-91
1-162-286-21
1-162-286-21
1-162-306-11
CERAMIC
ELECT
CERAMIC
CERAMIC
CERAMIC
0.0015uF
0.1uF
220PF
220PF
0.01uF
30%
20%
10%
10%
20%
16V
50V
50V
50V
16V
C152
C153
C154
C155
C156
1-162-282-31
1-162-282-31
1-126-961-11
1-162-600-11
1-162-301-11
CERAMIC
CERAMIC
ELECT
CERAMIC
CERAMIC
100PF
100PF
2.2uF
0.0047uF
0.0015uF
10%
10%
20%
30%
30%
50V
50V
50V
16V
16V
C157
C171
C172
C173
C191
1-126-956-91
1-162-286-21
1-162-286-21
1-162-306-11
1-126-963-11
ELECT
CERAMIC
CERAMIC
CERAMIC
ELECT
0.1uF
220PF
220PF
0.01uF
4.7uF
20%
10%
10%
20%
20%
50V
50V
50V
16V
50V
C192
C201
C202
C203
C204
1-164-159-21
1-136-167-00
1-136-167-00
1-130-493-00
1-130-493-00
CERAMIC
FILM
FILM
MYLAR
MYLAR
0.1uF
0.15uF
0.15uF
0.068uF
0.068uF
5%
5%
5%
5%
50V
50V
50V
50V
50V
C205
C206
C207
C208
C209
1-130-486-00
1-130-486-00
1-130-480-00
1-130-479-00
1-130-474-00
MYLAR
MYLAR
MYLAR
MYLAR
MYLAR
0.018uF
0.018uF
0.0056uF
0.0047uF
0.0018uF
10%
10%
5%
5%
5%
50V
50V
50V
50V
50V
C210
C211
C212
C213
C214
1-126-964-11
1-126-964-11
1-130-483-00
1-136-169-00
1-136-169-00
ELECT
ELECT
MYLAR
FILM
FILM
10uF
10uF
0.01uF
0.22uF
0.22uF
20%
20%
5%
5%
5%
50V
50V
50V
50V
50V
C215
C216
C221
C222
C223
1-162-294-31
1-136-167-00
1-126-967-11
1-126-967-11
1-126-964-11
CERAMIC
FILM
ELECT
ELECT
ELECT
0.001uF
0.15uF
47uF
47uF
10uF
10%
5%
20%
20%
20%
50V
50V
10V
10V
50V
C224
C226
C231
C251
C252
1-162-290-31
1-126-964-11
1-109-889-11
1-136-167-00
1-136-167-00
CERAMIC
ELECT
ELECT
FILM
FILM
470PF
10uF
1uF
0.15uF
0.15uF
10%
20%
20%
5%
5%
50V
50V
50V
50V
50V
C253
C254
C255
C256
C257
1-130-493-00
1-130-493-00
1-130-486-00
1-130-486-00
1-130-480-00
MYLAR
MYLAR
MYLAR
MYLAR
MYLAR
0.068uF
0.068uF
0.018uF
0.018uF
0.0056uF
5%
5%
10%
10%
5%
50V
50V
50V
50V
50V
< TRANSISTOR >
Q1001
Q1002
8-749-010-90 TRANSISTOR PHOTO REFLECTOR
NJL5165KA-H
8-749-010-90 TRANSISTOR PHOTO REFLECTOR
NJL5165KA-H
< RESISTOR >
R1001
R1002
R1003
R1004
R1005
1-247-818-11
1-247-820-11
1-249-414-11
1-247-834-11
1-247-818-11
CARBON
CARBON
CARBON
CARBON
CARBON
300
360
560
1.3K
300
5%
5%
5%
5%
5%
1/4W
1/4W
1/4W
1/4W
1/4W
< SWITCH >
S1001
S1002
S1003
S1004
S1005
1-692-832-11
1-692-832-11
1-572-248-11
1-571-281-21
1-571-281-21
SWITCH, PUSH (1 KEY) (DECK A PLAY)
SWITCH, PUSH (1 KEY) (DECK B PLAY)
SWITCH, LEAF (DECK A HALF)
SWITCH, LEAF (DECK A 120/70)
SWITCH, LEAF (DECK A REC)
S1006 1-572-248-11
SWITCH, LEAF (DECK B HALF)
S1008 1-571-281-21
SWITCH, LEAF (DECK B 120/70)
S1009 1-571-281-21
SWITCH, LEAF (DECK B REC)
************************************************************
1-664-017-11 LED BOARD
**********
*
< CONNECTOR >
CN671
1-506-481-11 PIN, CONNECTOR 2P
< DIODE >
D671
D672
D673
D674
8-719-058-03
8-719-058-03
8-719-058-03
8-719-058-03
DIODE
DIODE
DIODE
DIODE
SEL5423E-TP15 (BACK LIGHT)
SEL5423E-TP15 (BACK LIGHT)
SEL5423E-TP15 (BACK LIGHT)
SEL5423E-TP15 (BACK LIGHT)
< RESISTOR >
R791
1-249-412-11 CARBON
390
5%
1/4W
************************************************************
— 97 —
MAIN
Ref. No.
Part No.
Description
Part No.
Description
C258
C259
C260
C261
C262
1-130-479-00
1-130-474-00
1-126-964-11
1-126-964-11
1-130-483-00
MYLAR
MYLAR
ELECT
ELECT
MYLAR
0.0047uF
0.0018uF
10uF
10uF
0.01uF
5%
5%
20%
20%
5%
Remarks
50V
50V
50V
50V
50V
Ref. No.
C1534
C1551
C1552
C1553
C1554
1-126-935-11
1-130-479-00
1-162-290-31
1-164-159-21
1-126-960-11
ELECT
MYLAR
CERAMIC
CERAMIC
ELECT
470uF
0.0047uF
470PF
0.1uF
1uF
20%
5%
10%
20%
16V
50V
50V
50V
50V
Remarks
C263
C264
C276
C281
C282
1-136-169-00
1-136-169-00
1-126-964-11
1-104-665-11
1-126-961-11
FILM
FILM
ELECT
ELECT
ELECT
0.22uF
0.22uF
10uF
100uF
2.2uF
5%
5%
20%
20%
20%
50V
50V
50V
10V
50V
C1555
C1556
C1557
C1558
1-126-964-11
1-126-964-11
1-126-960-11
1-104-665-11
ELECT
ELECT
ELECT
ELECT
10uF
10uF
1uF
100uF
20%
20%
20%
20%
50V
50V
50V
10V
C283
C284
C291
C301
C302
1-104-665-11
1-126-934-11
1-126-959-11
1-126-967-11
1-164-159-21
ELECT
ELECT
ELECT
ELECT
CERAMIC
100uF
220uF
0.47uF
47uF
0.1uF
20%
20%
20%
20%
10V
10V
50V
10V
50V
C303
C304
C305
C309
C310
1-136-173-00
1-126-926-11
1-162-306-11
1-102-514-11
1-102-514-11
FILM
ELECT
CERAMIC
CERAMIC
CERAMIC
0.47uF
1000uF
0.01uF
22PF
22PF
5%
20%
20%
5%
5%
50V
10V
16V
50V
50V
C311
C315
C316
C390
C391
1-164-159-21
1-104-665-11
1-136-165-00
1-104-665-11
1-162-306-11
CERAMIC
ELECT
FILM
ELECT
CERAMIC
0.1uF
100uF
0.1uF
100uF
0.01uF
20%
5%
20%
20%
50V
10V
50V
10V
16V
C392
C393
C394
C396
C398
1-104-665-11
1-126-925-11
1-164-159-21
1-126-961-11
1-126-961-11
ELECT
ELECT
CERAMIC
ELECT
ELECT
100uF
470uF
0.1uF
2.2uF
2.2uF
20%
20%
20%
20%
10V
10V
50V
50V
50V
C903
C904
C906
C909
C910
1-136-165-00
1-126-937-11
1-104-665-11
1-126-964-11
1-104-665-11
FILM
ELECT
ELECT
ELECT
ELECT
0.1uF
4700uF
100uF
10uF
100uF
5%
20%
20%
20%
20%
50V
16V
10V
50V
10V
C911
C912
C913
C914
C915
1-126-964-11
1-126-916-11
1-126-943-11
1-126-767-11
1-126-967-11
ELECT
ELECT
ELECT
ELECT
ELECT
10uF
1000uF
2200uF
1000uF
47uF
20%
20%
20%
20%
20%
50V
6.3V
25V
16V
16V
C916
C917
C918
C919
C920
1-164-159-21
1-126-968-11
1-126-968-11
1-126-964-11
1-126-947-11
CERAMIC
ELECT
ELECT
ELECT
ELECT
0.1uF
100uF
100uF
10uF
47uF
20%
20%
20%
20%
50V
50V
50V
50V
35V
C953
C954
C956
C1501
C1502
1-136-165-00
1-126-768-11
1-104-665-11
1-130-479-00
1-162-290-31
FILM
ELECT
ELECT
MYLAR
CERAMIC
0.1uF
2200uF
100uF
0.0047uF
470PF
5%
20%
20%
5%
10%
50V
16V
10V
50V
50V
C1503
C1504
C1505
C1506
C1507
1-164-159-21
1-126-960-11
1-126-964-11
1-126-964-11
1-126-960-11
CERAMIC
ELECT
ELECT
ELECT
ELECT
0.1uF
1uF
10uF
10uF
1uF
20%
20%
20%
20%
50V
50V
50V
50V
50V
C1508
C1523
C1531
C1532
C1533
1-104-665-11
1-126-933-11
1-164-159-21
1-164-159-21
1-164-159-21
ELECT
ELECT
CERAMIC
CERAMIC
CERAMIC
100uF
100uF
0.1uF
0.1uF
0.1uF
< CONNECTOR >
20%
20%
CN101
* CN102
* CN105
* CN201
CN202
1-778-982-11
1-568-836-11
1-564-518-11
1-568-832-11
1-568-802-11
CONNECTOR, BOARD TO BOARD 13P
SOCKET, CONNECTOR 17P
PLUG, CONNECTOR 3P
SOCKET, CONNECTOR 13P
SOCKET, CONNECTOR 19P
* CN203
CN205
* CN206
* CN207
1-568-936-11
1-568-838-11
1-568-830-11
1-568-449-11
PIN, CONNECTOR 9P
SOCKET, CONNECTOR 21P
SOCKET, CONNECTOR 11P
HOUSING, CONNECTOR (PC BOARD) 3P
< DIODE >
D141
D142
D191
D192
D291
8-719-991-33
8-719-991-33
8-719-991-33
8-719-991-33
8-719-991-33
DIODE
DIODE
DIODE
DIODE
DIODE
1SS133T-77
1SS133T-77
1SS133T-77
1SS133T-77
1SS133T-77
D301
D302
D303
D304
D305
8-719-200-82
8-719-200-82
8-719-991-33
8-719-991-33
8-719-991-33
DIODE
DIODE
DIODE
DIODE
DIODE
11ES2
11ES2
1SS133T-77
1SS133T-77
1SS133T-77
D306
D307
D309
D902
D903
8-719-991-33
8-719-991-33
8-719-991-33
8-719-200-82
8-719-200-82
DIODE
DIODE
DIODE
DIODE
DIODE
1SS133T-77
1SS133T-77
1SS133T-77
11ES2
11ES2
D904
D905
D906
D907
D908
8-719-200-82
8-719-200-82
8-719-200-82
8-719-200-82
8-719-200-82
DIODE
DIODE
DIODE
DIODE
DIODE
11ES2
11ES2
11ES2
11ES2
11ES2
D909
D910
D911
D912
D913
8-719-200-82
8-719-982-27
8-719-109-89
8-719-991-33
8-719-200-82
DIODE
DIODE
DIODE
DIODE
DIODE
11ES2
MTZJ-33C
RD5.6ESB2
1SS133T-77
11ES2
D914
D915
D951
D952
8-719-200-82
8-719-935-69
8-719-991-33
8-719-991-33
DIODE
DIODE
DIODE
DIODE
11ES2
UZL-11M1-TA
1SS133T-77
1SS133T-77
< FERRITE BEAD >
FB302
10V
16V
50V
50V
50V
— 98 —
1-412-473-21 INDUCTOR 0uH
MAIN
Ref. No.
Part No.
Description
Remarks
Ref. No.
Part No.
Description
< IC >
Remarks
< RESISTOR >
IC101
IC102
IC201
IC231
IC281
8-759-634-50
8-759-000-48
8-759-460-02
8-759-634-50
8-759-111-68
IC
IC
IC
IC
IC
M5218AL
MC14052BCP
M62427FP-A
M5218AL
UPC1237HA
R102
R103
R104
R105
R106
1-249-417-11
1-249-437-11
1-249-417-11
1-247-897-11
1-249-437-11
CARBON
CARBON
CARBON
CARBON
CARBON
1K
47K
1K
560K
47K
5%
5%
5%
5%
5%
1/4W
1/4W
1/4W
1/4W
1/4W
IC301
IC302
IC391
IC901
IC902
8-759-531-31
8-759-635-63
8-749-923-04
8-759-288-53
8-759-604-86
IC
IC
IC
IC
IC
uPD780018YGF-028-3BA
M51943BSL
TOTX178 (CD DIGITAL OUT)
LA5617
M5F7807L
R107
R108
R121
R122
R123
1-249-417-11
1-249-441-11
1-249-424-11
1-247-887-00
1-249-426-11
CARBON
CARBON
CARBON
CARBON
CARBON
1K
100K
3.9K
220K
5.6K
5%
5%
5%
5%
5%
1/4W
1/4W
1/4W
1/4W
1/4W
IC903
IC904
IC1501
IC1502
8-759-231-53
8-759-231-58
8-759-363-21
8-759-822-09
IC
IC
IC
IC
TA7805S
TA7812S
HA12203NT
LB1641
R124
R125
R126
R127
R133
1-249-429-11
1-249-441-11
1-249-417-11
1-249-441-11
1-260-091-11
CARBON
CARBON
CARBON
CARBON
CARBON
10K
100K
1K
100K
220
5%
5%
5%
5%
5%
1/4W
1/4W
1/4W
1/4W
1/2W
R134
R140
R141
R142
! R147
1-260-091-11
1-249-429-11
1-249-437-11
1-249-429-11
1-216-456-00
CARBON
CARBON
CARBON
CARBON
METAL OXIDE
220
10K
47K
10K
820
5%
5%
5%
5%
5%
1/2W
1/4W
1/4W
1/4W
2W
F
! R148
R152
R153
R154
R155
1-216-456-00
1-249-417-11
1-249-437-11
1-249-417-11
1-247-897-11
METAL OXIDE
CARBON
CARBON
CARBON
CARBON
820
1K
47K
1K
560K
5%
5%
5%
5%
5%
2W
F
1/4W
1/4W
1/4W
1/4W
R156
R157
R158
R171
R172
1-249-437-11
1-249-417-11
1-249-441-11
1-249-424-11
1-247-887-00
CARBON
CARBON
CARBON
CARBON
CARBON
47K
1K
100K
3.9K
220K
5%
5%
5%
5%
5%
1/4W
1/4W
1/4W
1/4W
1/4W
R173
R174
R176
R177
R183
1-249-426-11
1-249-429-11
1-249-417-11
1-249-441-11
1-260-091-11
CARBON
CARBON
CARBON
CARBON
CARBON
5.6K
10K
1K
100K
220
5%
5%
5%
5%
5%
1/4W
1/4W
1/4W
1/4W
1/2W
R184
R191
R192
R193
R194
1-260-091-11
1-249-425-11
1-249-441-11
1-249-421-11
1-249-437-11
CARBON
CARBON
CARBON
CARBON
CARBON
220
4.7K
100K
2.2K
47K
5%
5%
5%
5%
5%
1/2W
1/4W
1/4W
1/4W
1/4W
R195
R201
R202
R203
R205
1-249-437-11
1-249-429-11
1-247-863-91
1-249-441-11
1-247-863-91
CARBON
CARBON
CARBON
CARBON
CARBON
47K
10K
22K
100K
22K
5%
5%
5%
5%
5%
1/4W
1/4W
1/4W
1/4W
1/4W
R206
R207
R209
R210
R211
1-249-421-11
1-249-431-11
1-249-441-11
1-247-896-11
1-247-891-00
CARBON
CARBON
CARBON
CARBON
CARBON
2.2K
15K
100K
510K
330K
5%
5%
5%
5%
5%
1/4W
1/4W
1/4W
1/4W
1/4W
R212
R213
R214
R215
R216
1-247-826-00
1-249-429-11
1-249-437-11
1-247-903-00
1-249-429-11
CARBON
CARBON
CARBON
CARBON
CARBON
620
10K
47K
1M
10K
5%
5%
5%
5%
5%
1/4W
1/4W
1/4W
1/4W
1/4W
< JACK >
J101
1-784-275-11 JACK, PIN 6P (PHONO, VIDEO/MD (AUDIO))
< COIL >
L301
L393
1-410-509-11 INDUCTOR 10uH
1-410-515-11 INDUCTOR 33uH
< TRANSISTOR >
Q101
Q102
Q103
Q141
Q142
8-729-141-30
8-729-029-40
8-729-029-86
8-729-140-82
8-729-140-84
TRANSISTOR
TRANSISTOR
TRANSISTOR
TRANSISTOR
TRANSISTOR
2SC3623A-LK
DTA124ESA
DTC124ESA
2SA988-PAFAEA
2SC1841-PAFAEA
Q151
Q191
Q192
Q201
Q202
8-729-141-30
8-729-119-76
8-729-111-29
8-729-029-86
8-729-620-05
TRANSISTOR
TRANSISTOR
TRANSISTOR
TRANSISTOR
TRANSISTOR
2SC3623A-LK
2SA1175-HFE
2SD1616A-K
DTC124ESA
2SC2603-EF
Q203
Q204
Q231
Q232
Q251
8-729-620-05
8-729-141-30
8-729-029-40
8-729-029-40
8-729-029-86
TRANSISTOR
TRANSISTOR
TRANSISTOR
TRANSISTOR
TRANSISTOR
2SC2603-EF
2SC3623A-LK
DTA124ESA
DTA124ESA
DTC124ESA
Q252
Q253
Q254
Q281
Q282
8-729-620-05
8-729-620-05
8-729-141-30
8-729-029-86
8-729-029-40
TRANSISTOR
TRANSISTOR
TRANSISTOR
TRANSISTOR
TRANSISTOR
2SC2603-EF
2SC2603-EF
2SC3623A-LK
DTC124ESA
DTA124ESA
Q283
Q301
Q901
Q902
Q903
8-729-029-86
8-729-620-05
8-729-040-20
8-729-029-86
8-729-026-68
TRANSISTOR
TRANSISTOR
TRANSISTOR
TRANSISTOR
TRANSISTOR
DTC124ESA
2SC2603-EF
RT1P137L-TP
DTC124ESA
2SD2525(TP)
Q904
Q905
Q906
Q907
Q1531
8-729-030-19
8-729-040-20
8-729-029-40
8-729-620-05
8-729-801-93
TRANSISTOR
TRANSISTOR
TRANSISTOR
TRANSISTOR
TRANSISTOR
2SB1640
RT1P137L-TP
DTA124ESA
2SC2603-EF
2SD1387
Q1532
Q1533
Q1534
Q1535
8-729-029-66
8-729-029-66
8-729-119-77
8-729-029-66
TRANSISTOR
TRANSISTOR
TRANSISTOR
TRANSISTOR
DTC114ESA
DTC114ESA
2SA1175-FEK
DTC114ESA
— 99 —
The components identified by mark ! or dotted
line with mark ! are critical for safety.
Replace only with part number specified.
MAIN
Ref. No.
Part No.
Description
Part No.
Description
R217
R221
R222
R226
R227
1-249-437-11
1-249-425-11
1-249-425-11
1-249-421-11
1-249-441-11
CARBON
CARBON
CARBON
CARBON
CARBON
47K
4.7K
4.7K
2.2K
100K
5%
5%
5%
5%
5%
1/4W
1/4W
1/4W
1/4W
1/4W
Remarks
Ref. No.
R330
R331
R332
R333
R339
1-247-807-31
1-247-807-31
1-247-807-31
1-247-807-31
1-247-807-31
CARBON
CARBON
CARBON
CARBON
CARBON
100
100
100
100
100
5%
5%
5%
5%
5%
1/4W
1/4W
1/4W
1/4W
1/4W
R228
R231
R232
R234
R235
1-249-429-11
1-249-437-11
1-249-437-11
1-247-886-11
1-249-421-11
CARBON
CARBON
CARBON
CARBON
CARBON
10K
47K
47K
200K
2.2K
5%
5%
5%
5%
5%
1/4W
1/4W
1/4W
1/4W
1/4W
R340
R341
R342
R344
R345
1-247-807-31
1-247-807-31
1-247-807-31
1-247-807-31
1-247-807-31
CARBON
CARBON
CARBON
CARBON
CARBON
100
100
100
100
100
5%
5%
5%
5%
5%
1/4W
1/4W
1/4W
1/4W
1/4W
R236
R238
R239
R253
R257
1-249-441-11
1-249-438-11
1-249-437-11
1-249-441-11
1-249-431-11
CARBON
CARBON
CARBON
CARBON
CARBON
100K
56K
47K
100K
15K
5%
5%
5%
5%
5%
1/4W
1/4W
1/4W
1/4W
1/4W
R346
R349
R350
R351
R352
1-247-807-31
1-247-807-31
1-247-807-31
1-247-807-31
1-247-807-31
CARBON
CARBON
CARBON
CARBON
CARBON
100
100
100
100
100
5%
5%
5%
5%
5%
1/4W
1/4W
1/4W
1/4W
1/4W
R259
R260
R261
R262
R263
1-249-441-11
1-247-896-11
1-247-891-00
1-247-826-00
1-249-429-11
CARBON
CARBON
CARBON
CARBON
CARBON
100K
510K
330K
620
10K
5%
5%
5%
5%
5%
1/4W
1/4W
1/4W
1/4W
1/4W
R353
R354
R355
R356
R357
1-247-807-31
1-247-807-31
1-247-807-31
1-247-807-31
1-247-807-31
CARBON
CARBON
CARBON
CARBON
CARBON
100
100
100
100
100
5%
5%
5%
5%
5%
1/4W
1/4W
1/4W
1/4W
1/4W
R264
R265
R266
R267
R271
1-249-437-11
1-247-903-00
1-249-429-11
1-249-437-11
1-249-425-11
CARBON
CARBON
CARBON
CARBON
CARBON
47K
1M
10K
47K
4.7K
5%
5%
5%
5%
5%
1/4W
1/4W
1/4W
1/4W
1/4W
R359
R360
R366
R367
R368
1-247-807-31
1-247-807-31
1-247-807-31
1-249-429-11
1-247-843-11
CARBON
CARBON
CARBON
CARBON
CARBON
100
100
100
10K
3.3K
5%
5%
5%
5%
5%
1/4W
1/4W
1/4W
1/4W
1/4W
R272
R276
R277
R278
R281
1-249-425-11
1-249-421-11
1-249-441-11
1-249-429-11
1-249-426-11
CARBON
CARBON
CARBON
CARBON
CARBON
4.7K
2.2K
100K
10K
5.6K
5%
5%
5%
5%
5%
1/4W
1/4W
1/4W
1/4W
1/4W
R369
R384
R395
R396
R397
1-249-429-11
1-249-429-11
1-247-807-31
1-249-435-11
1-247-807-31
CARBON
CARBON
CARBON
CARBON
CARBON
10K
10K
100
33K
100
5%
5%
5%
5%
5%
1/4W
1/4W
1/4W
1/4W
1/4W
R282
R283
R284
R285
R286
1-249-426-11
1-249-435-11
1-247-791-91
1-249-441-11
1-249-429-11
CARBON
CARBON
CARBON
CARBON
CARBON
5.6K
33K
22
100K
10K
5%
5%
5%
5%
5%
1/4W
1/4W
1/4W
1/4W
1/4W
R398
R417
R913
R914
R915
1-249-435-11
1-249-441-11
1-247-815-91
1-249-417-11
1-249-425-11
CARBON
CARBON
CARBON
CARBON
CARBON
33K
100K
220
1K
4.7K
5%
5%
5%
5%
5%
1/4W
1/4W
1/4W
1/4W
1/4W
R287
R288
R289
R291
R292
1-249-425-11
1-249-439-11
1-249-440-11
1-247-863-91
1-247-863-91
CARBON
CARBON
CARBON
CARBON
CARBON
4.7K
68K
82K
22K
22K
5%
5%
5%
5%
5%
1/4W
1/4W
1/4W
1/4W
1/4W
R916
R917
R918
R920
R921
1-247-815-91
1-247-815-91
1-249-425-11
1-249-417-11
1-247-895-91
CARBON
CARBON
CARBON
CARBON
CARBON
220
220
4.7K
1K
470K
5%
5%
5%
5%
5%
1/4W
1/4W
1/4W
1/4W
1/4W
R293
R294
R295
R301
R302
1-249-421-11
1-249-441-11
1-247-903-00
1-249-413-11
1-249-425-11
CARBON
CARBON
CARBON
CARBON
CARBON
2.2K
100K
1M
470
4.7K
5%
5%
5%
5%
5%
1/4W
1/4W
1/4W
1/4W
1/4W
R951
R952
R1501
R1502
R1503
1-249-425-11
1-249-425-11
1-249-435-11
1-249-417-11
1-249-426-11
CARBON
CARBON
CARBON
CARBON
CARBON
4.7K
4.7K
33K
1K
5.6K
5%
5%
5%
5%
5%
1/4W
1/4W
1/4W
1/4W
1/4W
R303
R304
R305
R313
R316
1-249-437-11
1-249-437-11
1-249-429-11
1-247-807-31
1-249-429-11
CARBON
CARBON
CARBON
CARBON
CARBON
47K
47K
10K
100
10K
5%
5%
5%
5%
5%
1/4W
1/4W
1/4W
1/4W
1/4W
R1504
R1505
R1506
R1507
R1521
1-247-840-00
1-247-863-91
1-249-421-11
1-249-428-11
1-247-852-11
CARBON
CARBON
CARBON
CARBON
CARBON
2.4K
22K
2.2K
8.2K
7.5K
5%
5%
5%
5%
5%
1/4W
1/4W
1/4W
1/4W
1/4W
R318
R319
R320
R322
R323
1-249-429-11
1-249-429-11
1-249-429-11
1-249-425-11
1-247-807-31
CARBON
CARBON
CARBON
CARBON
CARBON
10K
10K
10K
4.7K
100
5%
5%
5%
5%
5%
1/4W
1/4W
1/4W
1/4W
1/4W
R1522
R1524
R1525
R1526
R1527
1-249-422-11
1-249-429-11
1-249-432-11
1-249-429-11
1-249-429-11
CARBON
CARBON
CARBON
CARBON
CARBON
2.7K
10K
18K
10K
10K
5%
5%
5%
5%
5%
1/4W
1/4W
1/4W
1/4W
1/4W
R324
R325
R326
R327
R328
1-247-891-00
1-249-431-11
1-249-415-11
1-247-807-31
1-247-807-31
CARBON
CARBON
CARBON
CARBON
CARBON
330K
15K
680
100
100
5%
5%
5%
5%
5%
1/4W
1/4W
1/4W
1/4W
1/4W
R1531
R1532
R1533
R1534
R1535
1-247-843-11
1-249-411-11
1-249-427-11
1-249-429-11
1-249-425-11
CARBON
CARBON
CARBON
CARBON
CARBON
3.3K
330
6.8K
10K
4.7K
5%
5%
5%
5%
5%
1/4W
1/4W
1/4W
1/4W
1/4W
— 100 —
Remarks
MAIN
Ref. No.
Remarks
Part No.
Description
Part No.
Description
R1536
R1541
R1542
R1543
R1544
1-249-425-11
1-249-425-11
1-249-425-11
1-249-425-11
1-249-417-11
CARBON
CARBON
CARBON
CARBON
CARBON
4.7K
4.7K
4.7K
4.7K
1K
5%
5%
5%
5%
5%
1/4W
1/4W
1/4W
1/4W
1/4W
C626
C627
C628
C629
C630
1-126-957-11
1-136-159-00
1-162-302-11
1-126-957-11
1-162-293-31
ELECT
FILM
CERAMIC
ELECT
CERAMIC
0.22uF
0.033uF
0.0022uF
0.22uF
820PF
20%
5%
30%
20%
10%
50V
50V
16V
50V
50V
R1545
R1546
R1547
R1548
R1551
1-249-437-11
1-249-437-11
1-249-437-11
1-249-437-11
1-247-863-91
CARBON
CARBON
CARBON
CARBON
CARBON
47K
47K
47K
47K
22K
5%
5%
5%
5%
5%
1/4W
1/4W
1/4W
1/4W
1/4W
C631
C632
C641
C642
C643
1-126-957-11
1-126-957-11
1-162-286-21
1-162-286-21
1-162-286-21
ELECT
ELECT
CERAMIC
CERAMIC
CERAMIC
0.22uF
0.22uF
220PF
220PF
220PF
20%
20%
10%
10%
10%
50V
50V
50V
50V
50V
R1552
R1553
R1554
R1555
R1556
1-249-417-11
1-249-426-11
1-247-840-00
1-247-863-91
1-249-421-11
CARBON
CARBON
CARBON
CARBON
CARBON
1K
5.6K
2.4K
22K
2.2K
5%
5%
5%
5%
5%
1/4W
1/4W
1/4W
1/4W
1/4W
C644
C645
C646
C647
C648
1-162-286-21
1-162-286-21
1-162-286-21
1-162-286-21
1-162-286-21
CERAMIC
CERAMIC
CERAMIC
CERAMIC
CERAMIC
220PF
220PF
220PF
220PF
220PF
10%
10%
10%
10%
10%
50V
50V
50V
50V
50V
R1557
1-249-428-11 CARBON
8.2K
5%
1/4W
C649
C650
C651
C652
C653
1-162-286-21
1-162-286-21
1-162-286-21
1-162-286-21
1-162-286-21
CERAMIC
CERAMIC
CERAMIC
CERAMIC
CERAMIC
220PF
220PF
220PF
220PF
220PF
10%
10%
10%
10%
10%
50V
50V
50V
50V
50V
C654
C655
C656
C695
C696
1-162-286-21
1-162-286-21
1-162-286-21
1-164-159-21
1-164-159-21
CERAMIC
CERAMIC
CERAMIC
CERAMIC
CERAMIC
220PF
220PF
220PF
0.1uF
0.1uF
10%
10%
10%
50V
50V
50V
50V
50V
C697
1-162-294-31 CERAMIC
0.001uF
10%
50V
< VARIABLE RESISTOR >
RV1501 1-238-598-11 RES, ADJ, CARBON 2.2K
RV1551 1-238-598-11 RES, ADJ, CARBON 2.2K
< RELAY >
RY141
RY142
1-755-141-11 RELAY
1-755-141-11 RELAY
< TERMINAL >
TM131
Ref. No.
PANEL
1-537-925-41 TERMINAL BOARD (SPEAKER)
Remarks
< CONNECTOR >
< VIBRATOR >
X301
1-760-489-11 VIBRATOR, CERAMIC (5MHz)
X302
1-567-098-41 VIBRATOR, CRYSTAL (32.768kHz)
************************************************************
* CN601
* CN602
CN603
* CN604
1-568-836-11
1-568-947-11
1-506-486-11
1-568-947-11
SOCKET, CONNECTOR 17P
PIN, CONNECTOR 9P
PIN, CONNECTOR 7P
PIN, CONNECTOR 9P
< DIODE >
A-4403-858-A PANEL BOARD, COMPLETE
**********************
*
4-949-935-81 CUSHION (FL)
4-986-870-01 HOLDER, FL TUBE
*
*
D601
D602
D603
D604
D605
8-719-991-33
8-719-991-33
8-719-991-33
8-719-991-33
8-719-991-33
DIODE
DIODE
DIODE
DIODE
DIODE
1SS133T-77
1SS133T-77
1SS133T-77
1SS133T-77
1SS133T-77
D606
D607
D611
D612
D613
8-719-991-33
8-719-991-33
8-719-057-29
8-719-057-29
8-719-058-04
DIODE
DIODE
DIODE
DIODE
DIODE
1SS133T-77
1SS133T-77
SML78423C-TP15 (TUNER/BAND)
SML78423C-TP15 (TUNER/BAND)
SEL5223S-TP15 (ENTER/NEXT)
D614
D615
D616
D617
D618
8-719-058-04
8-719-058-04
8-719-058-04
8-719-058-04
8-719-058-04
DIODE
DIODE
DIODE
DIODE
DIODE
SEL5223S-TP15 (GROOVE)
SEL5223S-TP15 (SUPER WOOFER)
SEL5223S-TP15 (EFFECT)
SEL5223S-TP15 (ENTER)
SEL5223S-TP15 (FILE 1)
D619
D620
D621
D622
D623
8-719-058-04
8-719-058-04
8-719-058-04
8-719-058-04
8-719-058-04
DIODE
DIODE
DIODE
DIODE
DIODE
SEL5223S-TP15 (FILE 2)
SEL5223S-TP15 (FILE 3)
SEL5223S-TP15 (FILE 4)
SEL5223S-TP15 (FILE 5)
SEL5223S-TP15 (P FILE)
D624
D625
8-719-058-04 DIODE SEL5223S-TP15 (OTHERS)
8-719-058-04 DIODE SEL5223S-TP15 (MUSIC)
< CAPACITOR >
C601
C602
C603
C604
C606
1-126-967-11
1-162-306-11
1-126-963-11
1-126-960-11
1-126-960-11
ELECT
CERAMIC
ELECT
ELECT
ELECT
47uF
0.01uF
4.7uF
1uF
1uF
20%
20%
20%
20%
20%
50V
16V
50V
50V
50V
C608
C610
C611
C612
C613
1-126-382-11
1-162-306-11
1-162-306-11
1-126-967-11
1-164-159-21
ELECT
CERAMIC
CERAMIC
ELECT
CERAMIC
100uF
0.01uF
0.01uF
47uF
0.1uF
20%
20%
20%
20%
6.3V
16V
16V
50V
50V
C621
C622
C623
C624
C625
1-126-960-11
1-136-161-00
1-126-957-11
1-126-957-11
1-162-306-11
ELECT
FILM
ELECT
ELECT
CERAMIC
1uF
0.047uF
0.22uF
0.22uF
0.01uF
20%
5%
20%
20%
20%
50V
50V
50V
50V
16V
— 101 —
PANEL
Ref. No.
Part No.
Description
Remarks
< FERRITE BEAD >
FB601
1-412-473-21 INDUCTOR 0uH
< FLUORESCENT INDICATOR TUBE >
FL601
1-517-617-11 INDICATOR TUBE, FLUORESCENT
< IC >
IC601
IC602
8-759-526-36 IC TMP87CH75F-6659
8-759-459-84 IC NJL56H400
< COIL >
L601
1-410-509-11 INDUCTOR 10uH
Ref. No.
Part No.
Description
R633
R634
R635
R636
R637
1-247-897-11
1-247-897-11
1-247-897-11
1-247-897-11
1-247-895-91
CARBON
CARBON
CARBON
CARBON
CARBON
560K
560K
560K
560K
470K
5%
5%
5%
5%
5%
1/4W
1/4W
1/4W
1/4W
1/4W
Remarks
R638
R641
R642
R643
R644
1-249-435-11
1-249-419-11
1-249-401-11
1-249-403-11
1-247-807-31
CARBON
CARBON
CARBON
CARBON
CARBON
33K
1.5K
47
68
100
5%
5%
5%
5%
5%
1/4W
1/4W
1/4W
1/4W
1/4W
R645
R646
R647
R648
R649
1-249-407-11
1-249-407-11
1-247-815-91
1-249-411-11
1-249-413-11
CARBON
CARBON
CARBON
CARBON
CARBON
150
150
220
330
470
5%
5%
5%
5%
5%
1/4W
1/4W
1/4W
1/4W
1/4W
R650
R651
R652
R653
R654
1-249-415-11
1-249-417-11
1-249-419-11
1-249-421-11
1-247-843-11
CARBON
CARBON
CARBON
CARBON
CARBON
680
1K
1.5K
2.2K
3.3K
5%
5%
5%
5%
5%
1/4W
1/4W
1/4W
1/4W
1/4W
R655
R656
R657
R658
R659
1-249-427-11
1-249-431-11
1-249-419-11
1-249-401-11
1-249-403-11
CARBON
CARBON
CARBON
CARBON
CARBON
6.8K
15K
1.5K
47
68
5%
5%
5%
5%
5%
1/4W
1/4W
1/4W
1/4W
1/4W
R660
R661
R662
R663
R664
1-247-807-31
1-249-407-11
1-249-407-11
1-249-419-11
1-249-401-11
CARBON
CARBON
CARBON
CARBON
CARBON
100
150
150
1.5K
47
5%
5%
5%
5%
5%
1/4W
1/4W
1/4W
1/4W
1/4W
R665
R666
R667
R668
R669
1-249-403-11
1-247-807-31
1-249-407-11
1-249-407-11
1-249-419-11
CARBON
CARBON
CARBON
CARBON
CARBON
68
100
150
150
1.5K
5%
5%
5%
5%
5%
1/4W
1/4W
1/4W
1/4W
1/4W
R670
R671
R672
R673
R674
1-249-401-11
1-249-403-11
1-247-807-31
1-249-407-11
1-249-407-11
CARBON
CARBON
CARBON
CARBON
CARBON
47
68
100
150
150
5%
5%
5%
5%
5%
1/4W
1/4W
1/4W
1/4W
1/4W
R675
R676
R677
R678
R679
1-247-815-91
1-249-411-11
1-249-413-11
1-249-415-11
1-249-419-11
CARBON
CARBON
CARBON
CARBON
CARBON
220
330
470
680
1.5K
5%
5%
5%
5%
5%
1/4W
1/4W
1/4W
1/4W
1/4W
R681
R682
R683
R684
R685
1-249-429-11
1-249-421-11
1-247-887-00
1-249-421-11
1-247-815-91
CARBON
CARBON
CARBON
CARBON
CARBON
10K
2.2K
220K
2.2K
220
5%
5%
5%
5%
5%
1/4W
1/4W
1/4W
1/4W
1/4W
R686
R687
R688
R689
R690
1-247-807-31
1-247-807-31
1-247-807-31
1-247-807-31
1-247-807-31
CARBON
CARBON
CARBON
CARBON
CARBON
100
100
100
100
100
5%
5%
5%
5%
5%
1/4W
1/4W
1/4W
1/4W
1/4W
R691
R692
R693
R694
R695
1-247-807-31
1-247-807-31
1-247-807-31
1-247-807-31
1-247-807-31
CARBON
CARBON
CARBON
CARBON
CARBON
100
100
100
100
100
5%
5%
5%
5%
5%
1/4W
1/4W
1/4W
1/4W
1/4W
< TRANSISTOR >
Q601
Q602
Q603
Q604
Q605
8-729-178-59
8-729-118-00
8-729-118-00
8-729-119-77
8-729-119-77
TRANSISTOR
TRANSISTOR
TRANSISTOR
TRANSISTOR
TRANSISTOR
2SC2785
2SB1116-L
2SB1116-L
2SA1175-FEK
2SA1175-FEK
Q606
Q607
Q608
Q609
Q610
8-729-119-77
8-729-119-77
8-729-119-77
8-729-119-77
8-729-119-77
TRANSISTOR
TRANSISTOR
TRANSISTOR
TRANSISTOR
TRANSISTOR
2SA1175-FEK
2SA1175-FEK
2SA1175-FEK
2SA1175-FEK
2SA1175-FEK
Q611
Q614
Q615
Q617
Q618
8-729-119-77
8-729-119-77
8-729-119-77
8-729-119-77
8-729-119-77
TRANSISTOR
TRANSISTOR
TRANSISTOR
TRANSISTOR
TRANSISTOR
2SA1175-FEK
2SA1175-FEK
2SA1175-FEK
2SA1175-FEK
2SA1175-FEK
Q619
Q621
Q622
8-729-119-77 TRANSISTOR 2SA1175-FEK
8-729-119-77 TRANSISTOR 2SA1175-FEK
8-729-119-77 TRANSISTOR 2SA1175-FEK
< RESISTOR >
R601
R602
R603
R606
R607
1-249-427-11
1-249-435-11
1-247-903-00
1-249-429-11
1-249-429-11
CARBON
CARBON
CARBON
CARBON
CARBON
6.8K
33K
1M
10K
10K
5%
5%
5%
5%
5%
1/4W
1/4W
1/4W
1/4W
1/4W
R608
R609
R610
R611
R612
1-249-429-11
1-249-429-11
1-249-429-11
1-247-843-11
1-247-843-11
CARBON
CARBON
CARBON
CARBON
CARBON
10K
10K
10K
3.3K
3.3K
5%
5%
5%
5%
5%
1/4W
1/4W
1/4W
1/4W
1/4W
R613
R614
R615
R617
R621
1-249-401-11
1-249-429-11
1-249-429-11
1-249-429-11
1-249-421-11
CARBON
CARBON
CARBON
CARBON
CARBON
47
10K
10K
10K
2.2K
5%
5%
5%
5%
5%
1/4W
1/4W
1/4W
1/4W
1/4W
R622
R623
R624
R625
R626
1-249-437-11
1-247-895-91
1-249-421-11
1-249-437-11
1-247-895-91
CARBON
CARBON
CARBON
CARBON
CARBON
47K
470K
2.2K
47K
470K
5%
5%
5%
5%
5%
1/4W
1/4W
1/4W
1/4W
1/4W
R627
R628
R629
R631
R632
1-249-421-11
1-249-437-11
1-247-895-91
1-249-437-11
1-247-895-91
CARBON
CARBON
CARBON
CARBON
CARBON
2.2K
47K
470K
47K
470K
5%
5%
5%
5%
5%
1/4W
1/4W
1/4W
1/4W
1/4W
— 102 —
PANEL
Ref. No.
R696
R697
R698
R699
R700
Part No.
Description
1-247-807-31
1-247-807-31
1-247-807-31
1-247-807-31
1-247-807-31
CARBON
CARBON
CARBON
CARBON
CARBON
Remarks
100
100
100
100
100
5%
5%
5%
5%
5%
1/4W
1/4W
1/4W
1/4W
1/4W
< SWITCH >
S601
S602
S603
S604
S605
1-554-303-21
1-554-303-21
1-554-303-21
1-554-303-21
1-554-303-21
SWITCH, TACTILE (ENTER/NEXT)
SWITCH, TACTILE (TUNER MEMORY)
SWITCH, TACTILE (TUNING MODE)
SWITCH, TACTILE (TUNER/BAND)
SWITCH, TACTILE (TUNING +)
S606
S607
S609
S610
S611
1-554-303-21
1-554-303-21
1-554-303-21
1-554-303-21
1-554-303-21
SWITCH, TACTILE (TUNING -)
SWITCH, TACTILE (STEREO/MONO)
SWITCH, TACTILE (FUNCTION)
SWITCH, TACTILE (GROOVE)
SWITCH, TACTILE (GEQ 4)
S612
S613
S614
S615
S616
1-554-303-21
1-554-303-21
1-554-303-21
1-554-303-21
1-554-303-21
SWITCH, TACTILE (GEQ 9)
SWITCH, TACTILE (GEQ ()
SWITCH, TACTILE (GEQ $)
SWITCH, TACTILE (SUPER WOOFER)
SWITCH, TACTILE (SUPER W MODE)
S619
S620
S621
S622
S623
1-554-303-21
1-554-303-21
1-554-303-21
1-554-303-21
1-554-303-21
SWITCH, TACTILE (GEQ CONTROL)
SWITCH, TACTILE (ENTER)
SWITCH, TACTILE (EFFECT)
SWITCH, TACTILE (WAVE)
SWITCH, TACTILE (KARAOKE PON/MPX)
S624
S625
S627
S628
S629
1-554-303-21
1-554-303-21
1-554-303-21
1-554-303-21
1-554-303-21
SWITCH, TACTILE (SURROUND)
SWITCH, TACTILE (P FILE MEMORY)
SWITCH, TACTILE (SPECTRUM ANALYZER)
SWITCH, TACTILE (DISPLAY/DEMO)
SWITCH, TACTILE (I /u)
S630
S631
S632
S633
S634
1-554-303-21
1-554-303-21
1-554-303-21
1-554-303-21
1-554-303-21
SWITCH, TACTILE (t/CLOCK SET)
SWITCH, TACTILE (REC)
SWITCH, TACTILE (DAILY 1)
SWITCH, TACTILE (DAILY 2)
SWITCH, TACTILE (SLEEP)
S701
1-473-392-11 ENCODER, ROTARY (VOLUME)
Ref. No.
Part No.
Description
C813
C821
C822
C823
C824
1-162-294-31
1-126-963-11
1-162-286-21
1-162-282-31
1-126-967-11
CERAMIC
ELECT
CERAMIC
CERAMIC
ELECT
0.001uF
4.7uF
220PF
100PF
47uF
10%
20%
10%
10%
20%
50V
50V
50V
50V
10V
C826
C827
C829
C830
C831
1-126-967-11
1-126-965-11
1-126-965-11
1-164-159-21
1-130-493-00
ELECT
ELECT
ELECT
CERAMIC
MYLAR
47uF
22uF
22uF
0.1uF
0.068uF
20%
20%
20%
5%
50V
50V
50V
50V
50V
C832
C833
C841
C842
C843
1-130-493-00
1-162-294-31
1-136-165-00
1-126-307-11
1-126-925-11
MYLAR
CERAMIC
FILM
ELECT
ELECT
0.068uF
0.001uF
0.1uF
6800uF
470uF
5%
10%
5%
20%
20%
50V
50V
50V
50V
10V
C851
C852
C853
C854
C856
1-126-963-11
1-162-286-21
1-162-282-31
1-126-967-11
1-126-967-11
ELECT
CERAMIC
CERAMIC
ELECT
ELECT
4.7uF
220PF
100PF
47uF
47uF
20%
10%
10%
20%
20%
50V
50V
50V
10V
50V
C857
C858
C861
C862
C871
1-126-965-11
1-126-963-11
1-130-493-00
1-130-493-00
1-126-963-11
ELECT
ELECT
MYLAR
MYLAR
ELECT
22uF
4.7uF
0.068uF
0.068uF
4.7uF
20%
20%
5%
5%
20%
50V
50V
50V
50V
50V
C872
C873
C874
C876
C877
1-162-286-21
1-162-282-31
1-126-967-11
1-126-967-11
1-126-965-11
CERAMIC
CERAMIC
ELECT
ELECT
ELECT
220PF
100PF
47uF
47uF
22uF
10%
10%
20%
20%
20%
50V
50V
10V
50V
50V
C878
C881
C882
C891
C892
1-126-963-11
1-130-493-00
1-130-493-00
1-136-165-00
1-126-307-11
ELECT
MYLAR
MYLAR
FILM
ELECT
4.7uF
0.068uF
0.068uF
0.1uF
6800uF
20%
5%
5%
5%
20%
50V
50V
50V
50V
50V
C893
1-126-925-11 ELECT
470uF
20%
10V
CN801
1-778-981-11 CONNECTOR, BOARD TO BOARD 13P
X601
1-579-125-11 VIBRATOR, CERAMIC (8MHz)
************************************************************
A-4403-848-A POWER AMP BOARD, COMPLETE (EXCEPT TH)
***************************
A-4414-461-A POWER AMP BOARD, COMPLETE (TH)
***************************
*
7-685-646-79 SCREW +BVTP 3 × 8 TYPE2 N-S
< CAPACITOR >
C801
C802
C803
C804
C806
1-126-963-11
1-162-286-21
1-162-282-31
1-126-967-11
1-126-967-11
ELECT
CERAMIC
CERAMIC
ELECT
ELECT
4.7uF
220PF
100PF
47uF
47uF
20%
10%
10%
20%
20%
50V
50V
50V
10V
50V
C807
C809
C810
C811
C812
1-126-965-11
1-126-965-11
1-164-159-21
1-130-493-00
1-130-493-00
ELECT
ELECT
CERAMIC
MYLAR
MYLAR
22uF
22uF
0.1uF
0.068uF
0.068uF
20%
20%
50V
50V
50V
50V
50V
5%
5%
Remarks
< CONNECTOR >
< VIBRATOR >
*
POWER AMP
< DIODE >
D800
D801
D811
D821
D831
8-719-060-53
8-719-991-33
8-719-991-33
8-719-991-33
8-719-991-33
DIODE
DIODE
DIODE
DIODE
DIODE
RBV-2506
1SS133T-77
1SS133T-77
1SS133T-77
1SS133T-77
D841
D842
D851
D871
D891
8-719-991-33
8-719-991-33
8-719-991-33
8-719-991-33
8-719-991-33
DIODE
DIODE
DIODE
DIODE
DIODE
1SS133T-77
1SS133T-77
1SS133T-77
1SS133T-77
1SS133T-77
D892
8-719-991-33 DIODE 1SS133T-77
< IC >
IC801
IC821
— 103 —
8-749-921-04 IC STK-4211MK-2
8-749-921-04 IC STK-4211MK-2
POWER AMP
Ref. No.
Part No.
TABLE SENSOR
Description
TC-A SW
Remarks
Ref. No.
< TRANSISTOR >
Q801
Q821
Q851
Q871
8-729-140-84
8-729-140-84
8-729-140-84
8-729-140-84
TRANSISTOR
TRANSISTOR
TRANSISTOR
TRANSISTOR
1K
47K
750
R803
1-249-415-11 CARBON
680
R804
1-249-437-11 CARBON
47K
1/4W
1/4W
1/4W
(EXCEPT TH)
5%
1/4W
(TH)
5%
1/4W
R805
R806
! R807
R808
R809
1-260-107-11
1-260-107-11
1-212-881-11
1-217-156-00
1-260-076-11
CARBON
CARBON
FUSIBLE
METAL
CARBON
4.7K
4.7K
100
0.22
10
5%
5%
5%
10%
5%
1/2W
1/2W
1/4W F
5W
1/2W
R811
R812
R813
R814
R816
1-249-417-11
1-249-431-11
1-249-441-11
1-260-105-11
1-260-105-11
CARBON
CARBON
CARBON
CARBON
CARBON
1K
15K
100K
3.3K
3.3K
5%
5%
5%
5%
5%
1/4W
1/4W
1/4W
1/2W
1/2W
! R820
R821
R822
R823
1-202-972-61
1-249-417-11
1-249-437-11
1-247-828-11
FUSIBLE
CARBON
CARBON
CARBON
1
1K
47K
750
5%
5%
5%
5%
1-249-415-11 CARBON
680
R824
R825
R826
! R827
R828
1-249-437-11
1-260-107-11
1-260-107-11
1-212-881-11
1-217-156-00
CARBON
CARBON
CARBON
FUSIBLE
METAL
47K
4.7K
4.7K
100
0.22
5%
5%
5%
5%
10%
1/4W
1/2W
1/2W
1/4W F
5W
R829
R831
R832
R833
R834
1-260-076-11
1-249-417-11
1-249-431-11
1-249-441-11
1-260-105-11
CARBON
CARBON
CARBON
CARBON
CARBON
10
1K
15K
100K
3.3K
5%
5%
5%
5%
5%
1/2W
1/4W
1/4W
1/4W
1/2W
R836
! R840
R841
R842
R843
1-260-105-11
1-202-972-61
1-249-421-11
1-249-429-11
1-247-887-00
CARBON
FUSIBLE
CARBON
CARBON
CARBON
3.3K
1
2.2K
10K
220K
5%
5%
5%
5%
5%
1/2W
1/4W F
1/4W
1/4W
1/4W
R844
R851
R852
R853
1-249-429-11
1-249-417-11
1-249-437-11
1-247-828-11
CARBON
CARBON
CARBON
CARBON
10K
1K
47K
750
5%
5%
5%
5%
R853
1-249-415-11 CARBON
680
1-249-437-11
1-260-107-11
1-260-107-11
1-212-881-11
1-217-156-00
47K
4.7K
4.7K
100
0.22
R823
R871
R872
R873
1K
47K
750
5%
5%
5%
R873
1-249-415-11 CARBON
680
R874
1-249-437-11 CARBON
47K
1/4W
1/4W
1/4W
(EXCEPT TH)
5%
1/4W
(TH)
5%
1/4W
R875
R876
! R877
R878
R879
1-260-107-11
1-260-107-11
1-212-881-11
1-217-156-00
1-260-076-11
CARBON
CARBON
FUSIBLE
METAL
CARBON
4.7K
4.7K
100
0.22
10
5%
5%
5%
10%
5%
1/2W
1/2W
1/4W F
5W
1/2W
R881
R882
R883
R884
R891
1-249-417-11
1-249-431-11
1-249-441-11
1-249-437-11
1-249-421-11
CARBON
CARBON
CARBON
CARBON
CARBON
1K
15K
100K
47K
2.2K
5%
5%
5%
5%
5%
1/4W
1/4W
1/4W
1/4W
1/4W
1-659-058-13 TABLE SENSOR BOARD
*******************
*
< IC >
8-749-924-18 IC PHOTO INTERRUPTER RPI-1391
< RESISTOR >
R207
1-249-416-11 CARBON
820
5%
1/4W
************************************************************
1-664-012-11 TC-A SW BOARD
*************
*
< CONNECTOR >
CN612
CARBON
CARBON
CARBON
FUSIBLE
METAL
1/2W
1/4W
1/4W
1/4W
1/4W
R892
1-249-429-11 CARBON
10K
5%
1/4W
R893
1-247-887-00 CARBON
220K
5%
1/4W
R894
1-249-429-11 CARBON
10K
5%
1/4W
************************************************************
IC202
R854
R855
R856
! R857
R858
Remarks
1-249-417-11 CARBON
1-249-437-11 CARBON
1-247-828-11 CARBON
5%
5%
5%
1/4W F
1/4W
1/4W
1/4W
(EXCEPT TH)
5%
1/4W
(TH)
CARBON
CARBON
CARBON
CARBON
CARBON
5%
5%
5%
5%
5%
< RESISTOR >
1-249-417-11 CARBON
1-249-437-11 CARBON
1-247-828-11 CARBON
Description
1-260-076-11
1-249-437-11
1-249-417-11
1-249-431-11
1-249-441-11
10
47K
1K
15K
100K
2SC1841-PAFAEA
2SC1841-PAFAEA
2SC1841-PAFAEA
2SC1841-PAFAEA
R801
R802
R803
Part No.
R859
R860
R861
R862
R863
1-506-486-11 PIN, CONNECTOR 7P
< DIODE >
D631
D632
8-719-057-29 DIODE SML78423C-TP15 (·)
8-719-057-29 DIODE SML78423C-TP15 (ª)
1/4W
1/4W
1/4W
1/4W
(EXCEPT TH)
5%
1/4W
(TH)
R705
R706
R707
R708
R709
1-249-401-11
1-249-403-11
1-247-807-31
1-249-407-11
1-249-407-11
CARBON
CARBON
CARBON
CARBON
CARBON
47
68
100
150
150
5%
5%
5%
5%
5%
1/4W
1/4W
1/4W
1/4W
1/4W
5%
5%
5%
5%
10%
R710
R711
R712
R713
R714
1-247-815-91
1-247-807-31
1-247-807-31
1-247-807-31
1-247-807-31
CARBON
CARBON
CARBON
CARBON
CARBON
220
100
100
100
100
5%
5%
5%
5%
5%
1/4W
1/4W
1/4W
1/4W
1/4W
1/4W
1/2W
1/2W
1/4W F
5W
< RESISTOR >
— 104 —
The components identified by mark ! or dotted
line with mark ! are critical for safety.
Replace only with part number specified.
TC-A SW
Ref. No.
Part No.
Description
Remarks
Ref. No.
Part No.
1-554-303-21
1-554-303-21
1-554-303-21
1-554-303-21
1-554-303-21
TRANS
Description
< SWITCH >
S641
S642
S643
S644
S645
TC-B SW
Remarks
< FUSE HOLDER >
SWITCH, TACTILE (·)
SWITCH, TACTILE (ª)
SWITCH, TACTILE (p)
SWITCH, TACTILE (0)
SWITCH, TACTILE ())
FH901
FH902
FH951
FH952
1-533-399-11
1-533-399-11
1-533-399-11
1-533-399-11
HOLDER, FUSE
HOLDER, FUSE
HOLDER, FUSE
HOLDER, FUSE
< RESISTOR >
S646
1-554-303-21 SWITCH, TACTILE (DOLBY NR)
S647
1-554-303-21 SWITCH, TACTILE (DIRECTION)
************************************************************
1-664-013-11 TC-B SW BOARD
**************
*
! R901
! R902
! R903
! R904
1-219-119-81
1-219-119-81
1-219-119-81
1-219-119-81
FUSIBLE
FUSIBLE
FUSIBLE
FUSIBLE
0.1
0.1
0.1
0.1
5%
5%
5%
5%
1/4W
1/4W
1/4W
1/4W
F
F
F
F
< SWITCH >
< DIODE >
! S901
D635
D636
D637
D638
8-719-057-29
8-719-057-29
8-719-058-17
8-719-057-09
DIODE
DIODE
DIODE
DIODE
SML78423C-TP15 (ª)
SML78423C-TP15 (·)
LNG401NPYJA (P)
LNJ801LPDJA (r REC)
< TRANSFORMER >
! T901
1-431-638-11 TRANSFORMER, POWER
************************************************************
< RESISTOR >
R715
R716
R717
R718
R719
1-247-815-91
1-249-411-11
1-249-413-11
1-249-415-11
1-249-417-11
CARBON
CARBON
CARBON
CARBON
CARBON
220
330
470
680
1K
5%
5%
5%
5%
5%
1/4W
1/4W
1/4W
1/4W
1/4W
R720
R721
R722
R723
R724
1-249-419-11
1-249-421-11
1-247-843-11
1-247-807-31
1-247-807-31
CARBON
CARBON
CARBON
CARBON
CARBON
1.5K
2.2K
3.3K
100
100
5%
5%
5%
5%
5%
1/4W
1/4W
1/4W
1/4W
1/4W
R725
R726
R727
R728
1-247-807-31
1-247-807-31
1-247-807-31
1-247-807-31
CARBON
CARBON
CARBON
CARBON
100
100
100
100
5%
5%
5%
5%
1/4W
1/4W
1/4W
1/4W
1-554-303-21
1-554-303-21
1-554-303-21
1-554-303-21
1-554-303-21
SWITCH, TACTILE (·)
SWITCH, TACTILE (ª)
SWITCH, TACTILE ())
SWITCH, TACTILE (0)
SWITCH, TACTILE (p)
S656
1-554-303-21 SWITCH, TACTILE (P)
S657
1-554-303-21 SWITCH, TACTILE (r REC)
S658
1-554-303-21 SWITCH, TACTILE (H SPEED DUB)
S659
1-554-303-21 SWITCH, TACTILE (CD SYNC)
************************************************************
*
MISCELLANEOUS
**************
5
6
58
59
115
156
! 158
! 159
! 159
! 159
1-233-545-11 ENCAPSULATED COMPONENT
(FM/AM TUNER UNIT)
1-769-974-11 WIRE (FLAT TYPE) (13 CORE)
1-773-161-11 WIRE (FLAT TYPE) (21 CORE)
1-769-949-11 WIRE (FLAT TYPE) (11 CORE)
1-773-051-11 WIRE (FLAT TYPE) (17 CORE)
1-777-868-11
1-569-008-11
1-558-943-51
1-575-651-21
1-696-845-11
357
1-452-925-21
! 401
8-820-020-01
402
1-769-069-11
HP101 1-500-093-11
HRPE1011-500-094-11
< SWITCH >
S651
S652
S653
S654
S655
1-762-753-11 SWITCH, VOLTAGE SELECTION
(VOLTAGE SELECTOR)(EXCEPT TH)
M1
M2
M100
M101
M102
X-3371-223-1
A-2004-410-A
1-763-072-11
X-4917-504-1
X-4917-523-4
WIRE (FLAT TYPE) (19 CORE)
ADAPTOR, CONVERSION 2P (XB66: AR)
CORD, POWER (XB66: E, MX/XB660)
CORD, POWER (XB66: SAF, AR)
CORD, POWER (XB66: AUS)
MAGNET ASSY
OPTICAL PICK-UP KSS-213D/Q-NP
WIRE (FLAT TYPE) (16 CORE)
HEAD, MAGNETIC (PLAYBACK)
HEAD, MAGNETIC (REC/PB/ERASE)
MOTOR ASSY, CAPSTAN
MOTOR ASSY, DC (TRIGGER)
FAN, D.C.
MOTOR ASSY (SPINDLE)
MOTOR ASSY (SLED)
M201
A-4660-977-A MOTOR ASSY (TABLE)
! T901
1-431-638-11 TRANSFORMER, POWER
************************************************************
1-668-169-11 TRANS BOARD
************
< CONNECTOR >
* CN901
* CN902
CN903
CN903
1-564-522-11
1-564-518-11
1-535-139-00
1-774-108-11
PLUG, CONNECTOR 7P
PLUG, CONNECTOR 3P
BASE POST 14MM (10MM PITCH) 2P (E, IA)
PIN, CONNECTOR (PC BOARD) (EXCEPT E, IA)
< FUSE >
! F901
! F902
1-532-465-31 FUSE, TIME-LAG (3.15A/250V)
1-532-505-31 FUSE, TIME-LAG (5A/250V) (EXCEPT TH)
— 105 —
The components identified by mark ! or dotted
line with mark ! are critical for safety.
Replace only with part number specified.
HCD-XB66K
Ref. No.
Part No.
Description
Remarks
Ref. No.
Part No.
Description
Remarks
**************
HARDWARE LIST
**************
#1
#2
#3
#4
#5
7-685-646-79
7-685-871-01
7-685-872-09
7-685-650-79
7-685-862-09
SCREW +BVTP 3 × 8 TYPE2 N-S
SCREW +BVTT 3 × 6 (S)
SCREW +BVTT 3 × 8 (S)
SCREW +BVTP 3 × 16 TYPE2 IT-3
SCREW +BVTT 2.6 × 6 (S)
#6
#7
#8
#9
#10
7-685-131-19
7-685-533-19
7-621-775-10
7-685-534-19
7-623-921-01
SCREW +BTP 2.6 × 4 TYPE2 N-S
SCREW +BTP 2.6 × 6 TYPE2 N-S
SCREW +B 2.6 × 4
SCREW +BTP 2.6 × 8 TYPE2 N-S
RING, RETAINING, CAPSTAN
#11
7-621-775-00 SCREW +B 2.6 × 3
#12
7-621-255-15 SCREW +P 2 × 3
#13
7-685-881-09 SCREW +BVTT 4 × 8 (S)
************************************************************
ACCESSORIES & PACKING MATERIALS
********************************
1-475-115-31
1-501-374-11
1-501-659-41
3-862-180-11
REMOTE COMMANDER (RM-SD70)
ANTENNA, LOOP
ANTENNA (FM)
MANUAL, INSTRUCTION (ENGLISH)
(EXCEPT TH)
3-862-180-31 MANUAL, INSTRUCTION (FRENCH, SPANISH)
(EXCEPT IA, TH)
3-862-180-41 MANUAL, INSTRUCTION (CHINESE)
(EXCEPT TH)
3-862-180-91 MANUAL, INSTRUCTION (ARABIC) (EA)
3-862-960-11 MANUAL, INSTRUCTION (ENGLISH) (TH)
4-891-151-01 COVER, BATTERY (for RM-SD70)
Sony Corporation
9-922-833-11
Home A&V Products Company
— 106 —
98E167024-1
Printed in Singapore ©1998.5
Published by Quality Assurance Dept.
(Shibaura)
Download PDF
Similar pages