S/N: 3210 AND ABOVE
GB752
PLEASE CONTACT GAGE BILT FOR
ALL OTHER SERIAL NUMBERS.
INSTALLATION TOOL
GAGE BILT TOOLS ARE AVAILABLE WORLDWIDE
E-MAIL US FOR A DISTRIBUTOR NEAR YOU.
GAGE BILT
MADE IN U.S.A.
S/N: 3210 AND ABOVE
PLEASE CONTACT GAGE BILT FOR ALL OTHER SERIAL NUMBERS.
GAGE BILT Inc.
44766 Centre Court
(586) 226-1500
Clinton Twp. MI 48038 (586) 226-1505 Fax
e-mail:
solutions@gagebilt.com / www.gagebilt.com
REV.11/14
1
TABLE OF CONTENTS
Description
Page
Warnings ..................................................................................................................................................................................... 3
Principle of Operation ................................................................................................................................................................ 4
How to use the GB752 ............................................................................................................................................................... 5
Description, Operation and Maintenance ................................................................................................................................ 6
Filling, Bleeding and Troubleshooting ..................................................................................................................................... 7
Overhaul ..................................................................................................................................................................................... 8
Disassembly and Parts Lists................................................................................................................................................ 9-10
DEXRON® III Oil Safety Data ................................................................................................................................................... 11
Nose Assembly Selection Chart ............................................................................................................................................. 12
EU Conformity and Warranty .................................................................................................................................................. 13
SPECIFICATIONS
Hand Held Weight
Air pressure req'd
Air consumption
Hydraulic oil
-
Setting stroke
Rated pull load
Noise level
Vibration
-
S/N: 3210 AND ABOVE
PLEASE CONTACT GAGE BILT FOR ALL OTHER SERIAL NUMBERS.
4.30 lbs. (1.9 kg)
90-100 p.s.i. (6.2-6.9 bar)
3.9 CFM at 20 Cycles a minute
Automatic Transmission Oil,
Dexron III, or equivalent.
.500" (12.7 mm)
3,800 lbs. (16.9 kN)
81.5 dB (A)
Tested– No Hazards Found
2
REV.11/14
SAFETY WARNINGS
PLEASE READ THIS MANUAL BEFORE
SERVICING OR USING THIS TOOL.
WARNINGS:
CAUTIONS:
MUST BE UNDERSTOOD TO AVOID
SEVERE PERSONAL INJURY
SHOW CONDITIONS THAT WILL
DAMAGE EQUIPMENT OR STRUCTURE
WARNING
Do not operate without Stat-O-Seal (S572) and cap
screws (402482). Pressurized hydraulic oil may
cause severe personal injury.
WARNING
Do not pull fastener unless it is placed in an
assembly, pin will eject forcibly when pintail breaks
off. Severe personal injury may result.
WARNING
Always disconnect tool from power source before
performing any maintenance to any tool or nose
assembly.
WARNING
When operating, repairing or overhauling tool, wear
approved eye protection. Do not look in front of
nose assembly or rear of tool when installing
fastener.
WARNING
Ensure that all connections are properly secured
before connecting to power.
WARNING
Do not operate if deflector, bottle, catcher bag or
vacuum tube is removed or damaged, broken
pintails may eject forcibly from rear of tool. Severe
personal injury may result.
CAUTION
Ensure that nose assembly and tip are properly
matched for the fastener being installed.
CAUTION
Keep Nose Assemblies clean and free of chips and
debris.
WARNING
Be sure there is adequate clearance for tool and
operator's hands before proceeding. Keep fingers
clear of any moving parts. Keep fingers clear from
fasteners and installed materials. Severe personal
injury may result.
CAUTION
Do not use beyond the design intent.
WARNING
It is required to use hearing protection. A test was
carried out in a simulated work environment where
the background level was 73.2 dB (A). In this
condition the max level was 81.5 dB (A). Therefore,
it is required where prolonged use, hearing
protection be used.
WARNING
Tool must be maintained in a safe working
condition at all times and examined on a daily basis
for damage or wear. Any repair should be done by
qualified personnel trained on Gage Bilt
procedures.
WARNING
Where prolonged use is foreseen, it is
recommended a tool balancer be used. Check
suspension device to ensure that it is secure.
WARNING
Risk of crushing exists if nose assembly is not
attached.
WARNING
It is recommended tool be operated 50 out of every
60 minutes, where prolonged use is expected.
WARNING
Do no use tool in explosive atmosphere.
CAUTION
Tool is not to be used as a hammer.
WARNING
Shock:
It is recommended operator wear a suitable glove
during operation where prolonged use is expected.
S/N: 3210 AND ABOVE
PLEASE CONTACT GAGE BILT FOR ALL OTHER SERIAL NUMBERS.
WARNING
Air pressure not to exceed 100 psi (6.9 bar).
3
REV.11/14
PRINCIPLE OF OPERATION
When the actuator lever assy is depressed, the pressurized air inside of the tool is released allowing spring pressure to move the
valve spool assy causing the air to be redirected. The air is directed to the top of the air piston assy, moving it in a downward
direction. The air below the air piston assy is then directed through the valve sleeve and exhausted out of the bottom of the tool.
Simultaneously, the piston rod assy connected to the air piston assy is also moving down, forcing hydraulic oil up and into the front
side of the head cylinder assy, causing the piston to move to the rear of the head cylinder assy. The internal components of the
attached nose assembly are also moving with the piston to start the fastener installation. When the fastener installation is completed,
the actuator lever assy is released. Air pressure is then built up inside of the handle assy causing the valve spool assy to return to its
original position and reversing the sequence directing air pressure to the rear of the head cylinder assy, causing the piston to move to
the forward position.
CYLINDER
HEAD
HEAD
PISTON
AIR
PRESSURE
OIL
PRESSURE
AIR
PRESSURE
PISTON
ROD
AIR
PISTON
AIR
PRESSURE
AIR
PRESSURE
VALVE
SPOOL
AIR
PISTON
AIR
PRESSURE
AIR
PRESSURE
AIR
PRESSURE
EXHAUST
Image may not reflect actual tool
S/N: 3210 AND ABOVE
PLEASE CONTACT GAGE BILT FOR ALL OTHER SERIAL NUMBERS.
4
REV.11/14
HOW TO USE THE GB752
WARNING: Operator MUST read and understand all warnings and cautions.
WARNING: It is required that eye protection and hearing protection be worn during operation.
WARNING: Do not pull rivet in the air. Personal injury from fastener ejecting may occur.
WARNING: Air is exhausted from bottom of the tool. Direct bottom of the tool (exhausted air) away from operator, other
persons working in the vicinity, foreign matter and liquid.
CAUTION: Do not use beyond design intent.
The tool is shipped with a plastic plug in the air inlet connector. The connector has a 1/4-18 female pipe thread to accept end-user air
hose fitting. The tool comes with oil and is ready to use.
1. Remove plastic shipping plug from Swivel (A-249) and screw in your air fitting.
2. Attach Deflector (752122) to rear of head cylinder assy (752119).
WARNING: Rotate deflector away from operator and other persons working in the vicinity.
3. Connect air hose to tool (3/8 minimum diameter air line is mandatory, 90 p.s.i. (6.2 bar) is recommended) and cycle tool ten times
by depressing and releasing the actuator lever assy (704343). (Clean dry air is mandatory).
WARNING: Ensure air hose is securely connected to avoid possible hose whipping.
4. Disconnect air hose from tool.
5. Select proper Nose Assembly, screw collet and anvil onto the tool and attach securely. (See proper data sheet for further
instructions.)
6. Connect air supply.
7. Insert rivet into Nose Assembly and the application then depress actuator lever assy (704343). Upon releasing the actuator lever
assy (704343), the stem will eject to the rear of the tool.
WARNING: Always disconnect air supply when tool is not in use to prevent accidental start-up.
Image may not reflect actual tool
S/N: 3210 AND ABOVE
PLEASE CONTACT GAGE BILT FOR ALL OTHER SERIAL NUMBERS.
5
REV.11/14
DESCRIPTION
WARNING: The balance of the tool is designed for horizontal use and is not suited for any other application. Gage Bilt will
be pleased to advise for your specific application.
The GB752 is a pneumatic-hydraulic tool designed specifically for the efficient installation of a wide range of blind rivets. It weighs
4.30 lbs. (1.9 kg) and can be operated in any position with one hand. It has a .500" (12.7 mm) rivet setting stroke and a rated pull load
of 3800 lbs. (16.9 kN) with 90 psi (6.2 bar) air pressure at the air inlet.
The GB752 riveter is designed to operate on a range of air pressure, with 90 to 100 psi (6.2-6.9 bar) providing the maximum efficiency.
At 90 psi (6.2 bar) air pressure, the GB752 does not exceed 81.5 dB (A) and consumes 3.9 cfm at 20 cycles a minute.
The air inlet is provided with 1/4-18 female pipe threads to accept the users air hose fitting.
NOSE ASSEMBLIES ARE NOT FURNISHED WITH TOOL AND MUST BE ORDERED SEPARATELY. (See page 12 for nose assembly recommendations.)
MAINTENANCE
WARNING: Maintenance personnel MUST read and understand all warnings and cautions.
WARNING: Disconnect tool from its power source before performing maintenance.
WARNING: Excessive contact with hydraulic oil and lubricants should be avoided.
WARNING: Dispose of Hydraulic Oil in accordance with all environmental regulations applicable in your area.
WARNING: Read MSDS documents for all applicable materials.
The performance of any tool depends upon good maintenance practices. Following these minimal requirements for service and care
will extend the life of your tool.
*Only use an air supply set at 90-100 p.s.i. (6.2-6.9 bar) equipped with a filter-regulator to prevent wear.
*The tool will eventually lose some hydraulic oil. Keep the hydraulic system full (only use Dexron III, or equivalent) and free of air by
using the air bleeder assy (704153) on a weekly basis.
*Proper care by operator is necessary in maintaining full productivity and reducing downtime. Read all applicable tool manuals and
nose assembly data sheets prior to operating tools.
*Keep nose assemblies, especially jaws, clean and free of chips and debris. Lube jaws and collet surfaces that jaws ride on with light
machine oil on a daily basis.
*All Screwed End Caps, Base Covers, Air Fittings, Actuators, Screws and Nose Assemblies are to be examined at the end of each
working shift to check that they are secure.
*Check tool, all hoses and all couplings daily for damage or air/hydraulic leaks. Tighten or replace (if necessary).
*For a complete overhaul, tool kit (GB704TK) is recommended (see page 8).
CLEANING AND LUBRICATING PROCEDURE
Daily cleaning and lubrication of nose assembly will greatly reduce downtime
and increase life of components. Using sewing machine oil, or an equivalent
cleaner/lubricant, follow instructions below.
1. Disconnect tool vacuum line (if equipped).
2. Point nose assembly into oil as shown (Fig. A).
3. Cycle tool 8-10 times and wipe dry.
Fig A
Image may not reflect actual tool
TORQUE SPECIFICATIONS
Button Head Cap Screws (A-928) = 40 inch lbs.
Flexlock Nut (400559) = 40 inch lbs.
Packing Plug (704118) = 45 foot lbs.
End Cap (752313) = 45 foot lbs.
Button Head Cap Screws (402482) = 35-40 inch lbs. (Do NOT over-tighten)
S/N: 3210 AND ABOVE
PLEASE CONTACT GAGE BILT FOR ALL OTHER SERIAL NUMBERS.
6
REV.11/14
FILLING AND BLEEDING TOOL
NOTE: Air bleeder Assy (704153) is required.
WARNING: Do not cycle tool without air bleeder assy (704153), or the button head cap screw (402482) and stat-o-seal (S572),
installed in the head cylinder (752119). Severe personal injury may result.
CAUTION: Before filling handle assy (704132), the air piston assy (704121) should be all the way down.
CAUTION: When forcing piston rod assy (704138) downward with head cylinder assy (752119) removed, hydraulic oil will eject
forcibly from handle assy (704132).
CAUTION: Use CAUTION when removing button head cap screws (402482), stat-o-seals (S572) and air bleeder assy (704153). Hydraulic oil
may be under pressure.
WARNING: Failure to follow these instructions carefully may result in severe personal injury.
To replace a small amount of oil in the tool, attach the air bleeder assy (704153) and connect tool to air line. Cycle ten times. Disconnect air,
remove the air bleeder assy (704153), and reinstall the button head cap screw (402482) and stat-o-seal (S572). on the head cylinder assy
(752119). Torque 35-40 inch lbs. This will ensure the removal of any air from the hydraulic system and its replacement with oil.
* FILLING & BLEEDING VIDEO AVAILABLE AT: www.gagebilt.com/bleeding.wmv
Should it become necessary to completely refill the tool (such as would be required after tool has been dismantled and reassembled),
take the following steps after depressing the actuator lever assy (704343) AND DISCONNECTING THE AIR SUPPLY:
1. Remove head cylinder assy (752119) from handle assy (704132). Slowly push piston (752507) completely forward.
2. Fill handle assy (704132) and the oil passage on top of handle assy (704132) with automatic transmission oil, Dexron III or
equivalent. When looking at the top of the handle assy (704132), the oil passage is the hole that is counterbored for o'ring (S832).
3. Replace head cylinder assy (752119) with care, insuring gasket (704129) and o'ring (S832) are properly installed. Apply Loctite
242 to all four button head cap screws (A-928) and torque uniformly to 40 inch lbs. to prevent leakage around gasket (704129).
4. Remove button head cap screw (402482) and stat-o-seal (S572) from head cylinder assy (752119). Install air bleeder assy (704153)
and connect tool to air line, cycle ten times to fully circulate oil through hydraulic system.
5. DISCONNECT AIR FROM TOOL. Remove air bleeder assy (704153), install button head cap screw (402482) and stat-o-seal (S572)
in the head cylinder assy (752119).
6. Connect air supply. Cycle tool ten times and check stroke of .500 (12.7 mm) (see diagram below). We recommend using a pair of
dial calipers. With the actuator lever assy (704343) released, check dimension (A). With the actuator lever assy (704343)
depressed, check dimension (B). If stroke is not consistent within 1/64" (.0156) repeat bleeding steps 4-6.
'A'
.185 (4.7mm)
'B'
.685 (17.3mm)
TROUBLESHOOTING
Providing all maintenance conditions have been met, follow this systematic approach to diagnosis.
1. MORE THAN ONE PULL IS REQUIRED TO BREAK RIVET.
a) Tool needs to be bled. (See filling and bleeding instructions.)
b) Spring has fatigued, replace.
c) Jaws are stripped or packed with chips. Clean or replace.
2. SLOW OR PARTIAL OPERATION WHEN THE ACTUATOR LEVER ASSY (704343) IS DEPRESSED
a) Polyseal (A-1134) and o’ring (400791) on the piston (752507) could be worn or damaged. Replace.
b) Back-up ring (401102) and o’ring (S945) on the piston rod assy (704138) could be worn or damaged. Replace.
c) Muffler (704146) or filter inside valve spool assy (703142) may be plugged with dirt. Clean thoroughly and back-blow with
compressed air.
d) Hole in metering screw in valve spool assy (703142) may be blocked or damaged. Hole diameter should be .028". Clear
and size or replace.
3. NO OPERATION WHEN ACTUATOR LEVER ASSY (704343) DEPRESSED
a) Tool seized due to mechanical failure or damaged parts.
4. OIL LEAKAGE
a) DO NOT OPERATE WITH OIL LEAKING FROM TOOL. HIGH PRESSURE OIL MAY CAUSE SEVERE PERSONAL INJURY.
b) Any oil leaking externally should be traced to its source. An o'ring or seal that leaks should be replaced.
5. AIR BYPASS FROM VALVE HOUSING
a) If the spring (704141) breaks or dislodges, air will flow freely through the muffler (704146). Replace or reset. Valve spring
installation tool (704162) is recommended.
b) Check o'rings on valve sleeve (703139), valve spool assy (703142), and valve plug (704145). If worn or damaged, replace.
Valve sleeve removal tool (704163) is recommended.
6. FASTENER STEM JAMMED IN NOSE ASSEMBLY
a) Nose assembly components require service. DISCONNECT AIR FROM TOOL, remove the nose from the tool and
disassemble. Replace worn or broken parts. Clean the surface the jaws ride on.
b) Stems lodged side by side in the follower. Disassemble, remove stems, and reassemble.
c) Incorrect follower.
S/N: 3210 AND ABOVE
PLEASE CONTACT GAGE BILT FOR ALL OTHER SERIAL NUMBERS.
7
REV.11/14
OVERHAUL
WARNING: Disconnect tool from its air source before performing overhaul.
WARNING: Tool must be maintained in a safe working condition at all times and examined on a daily basis for damage or
wear. Any repair should be done by qualified personnel trained on Gage Bilt procedures.
WARNING: When operating, repairing or overhauling tool, wear approved eye protection. Do not look in front of tool or rear
of tool when installing fastener.
WARNING: Depress actuator lever assy and disconnect from air, with the piston in the rear position, before overhaul.
Severe personal injury may occur if air hose is not disconnected. USE CAUTION when forcing piston rod assy
downward with head cylinder removed. Hydraulic oil will eject forcibly from handle assy.
The disassembly and re-assembly procedure can be accomplished by utilizing the following instructions and drawings. Use extreme
care during disassembly and re-assembly not to mar or nick any smooth surface that comes in contact with seals. Before installing
seals, always apply a good lubricant, such as Lubriplate®, to the surfaces. It is recommended that tool kit (GB704TK) be used to
facilitate overhaul. A complete overhaul can be achieved by the use of Service Kit (752020) which contains a complete set of o'rings,
back-up rings, screws, washers and gasket. It is recommended that this service kit be kept available for spare parts.
704214
STEM CATCHER BAG
704152
SEAL GUIDE
704151
POWER CYLINDER TOOL
704149
PISTON ROD WRENCH
704150
PACKING PLUG WRENCH
704162
VALVE SPRING
INSTALLATION TOOL
S1178
VALVE EXTRACTOR
704163
VALVE SLEEVE
REMOVAL TOOL
704153
BLEEDER BOTTLE
(704214 CATCHER BAG AS SHOWN ABOVE IS SOLD SEPARATELY.)
GB704TK Service Tool Kit Includes:
Part No.
704149
704150
704151
704152
704153
S1178
704162
704163
Description
Piston Rod Wrench
Packing Plug Wrench
Power Cylinder Tool
Seal Guide
Bleeder Bottle
Valve Extractor
Valve Spring Installation Tool
Valve Sleeve Removal Tool
REMOVING 704130 AIR ACTUATOR ASSY
CAUTION: Air actuator assy can break if not careful.
1.
2.
3.
4.
Remove actuator lever assy (704343) including pin.
With actuator lever assy (704343) removed, insert a 5/8” (15.9 mm) open end
box wrench around air actuator assy (704130).
Loosen the air actuator assy (704130).
Remove wrench. Unthread and remove the air actuator assy (704130) with
fingers from the handle assy (704132).
INSTALLING 704130 AIR ACTUATOR ASSY
CAUTION: Do not over tighten air actuator assy. Snug tighten only.
1.
2.
3.
4.
Apply Teflon® tape onto threads of air actuator assy (704130) one to two wraps.
Thread the air actuator assy (704130) all the way into handle assy (704132) with fingers.
Insert and turn 5/8” (15.9 mm) open end box wrench and snug tight approximately
1/4-1/2 turn.
Re-attach the actuator lever assy (704343) with pin.
S/N: 3210 AND ABOVE
PLEASE CONTACT GAGE BILT FOR ALL OTHER SERIAL NUMBERS.
8
Image may not reflect actual tool
REV.11/14
HEAD
WARNING: Dispose of hydraulic oil in accordance with all environmental regulations applicable in your area.
Remove nose assembly and adapter from tool before attempting disassembly of head assy.
Remove end cap (752313). Push against threaded end of piston (752507) to slide it out of head cylinder assy (752119). Be careful not
to damage threads or cause burrs on polished piston (752507) surface.
The re-assembly sequence is the opposite of disassembly. (See Filling and Bleeding instructions.) Apply Loctite® #242 and torque
the button head cap screws (A-928) uniformly to 40 inch lbs. to prevent leakage around the gasket (704129).
S/N: 3210 AND ABOVE
PLEASE CONTACT GAGE BILT FOR ALL OTHER SERIAL NUMBERS.
9
REV.11/14
HANDLE
To inspect air cylinder bore, remove base cover (704125). Any further disassembly will require removal of the head cylinder assy
(752119) first. For complete disassembly, start by removing base cover (704125). Next, holding tool upright, remove four button-head
cap screws (A-928). Lift head cylinder assy (752119) from handle assy (704132) and set aside o'ring (S832) and gasket (704129).
Empty all hydraulic oil into an approved container and dispose of in accordance with all environmental regulations applicable in your
area. Place piston rod wrench (704149) down into top of power cylinder (751131) and into the hex of piston rod assy (704138). While
holding this wrench, remove flexlock nut (400559) using a 7/16" socket wrench. Still holding piston rod wrench (704149), remove air
piston assy (704121) using packing plug wrench (704150), by turning counterclockwise. When air piston assy (704121) is completely
free from piston rod assy (704138), tap or push on the piston rod wrench (704149) to eject air piston assy (704121) from bottom of
handle assy (704132). After removal of air piston assy (704121), slide piston rod assy (704138) back up to the end of its travel. Using
packing plug wrench (704150) remove packing plug (704118). With packing plug (704118) removed, power cylinder (751131) can be
removed by pushing on power cylinder tool (704151) when inserted into top of power cylinder (751131).
To reassemble the handle assy (704132), reverse the above procedure, being certain that all o'rings are properly lubricated before
installation. Torque packing plug (704118) to 45 foot lbs. Attach the seal guide (704152) to the piston rod assy (704138) and tap the
piston rod assy (704138) through the packing plug (704118). Attach air piston assy (704121) and flexlock nut (400559). Torque flexlock
nut to 40 inch lbs. Attach air piston assy (704121) to piston rod assy (704138). With the piston rod assy (704138) in the down position,
fill oil passage on top of handle assy (704132) with automatic transmission oil, Dexron III or equivalent. When looking at top of handle
assy (704132), the oil passage is the hole that has a counterbore for o'ring (S832). Replace gasket (704129) and o'ring (S832) just prior
to replacing head cylinder assy (752109). (See Filling & Bleeding instructions.)
AIR VALVE
WARNING: Disconnect tool from its air source before disassembly.
To disassemble, first disconnect tool from its air source. Remove pin (704244) and muffler (704146). Insert valve extractor (S1178)
into end of valve plug (704145) and pull it out. Using the same procedure, pull out valve spool assy (703142). NOTE: It should never
be necessary to remove valve sleeve (703139) unless the ports in the vavle sleeve (703139) are plugged from contaminated air. If
ports are plugged, use needle nose pliers to grasp end of spring (704141), turning clockwise and pulling to dislodge from groove in
casting. NOTE: Valve spring tool (704162) will facilitate the proper installation of the spring (704141), valve sleeve (703139) can be
pulled out using valve sleeve removal tool (704163).
S/N: 3210 AND ABOVE
PLEASE CONTACT GAGE BILT FOR ALL OTHER SERIAL NUMBERS.
10
REV.11/14
DEXRON® III OIL SAFETY DATA
FIRST AID MEASURES
Eye: No specific first aid measures are required. As a precaution, remove contact lenses, if worn, and flush eyes with water.
Skin: No specific first aid measures are required. As a precaution, remove clothing and shoes if contaminated. To remove the material
from skin, use soap and water. Discard contaminated clothing and shoes or thoroughly clean before reuse.
Ingestion: No specific first aid measures are required. Do not induce vomiting. As a precaution, get medical advice.
Inhalation: No specific first aid measures are required. If exposed to excessive levels of material in the air, move the exposed person to
fresh air. Get medical attention if coughing or respiratory discomfort occurs.
Note to Physicians: In an accident involving high-pressure equipment, this product may be injected under the skin. Such an accident
may result in a small, sometimes bloodless, puncture wound. However, because of its driving force, material injected into a fingertip can
be deposited into the palm of the hand. Within 24 hours, there is usually a great deal of swelling, discoloration, and intense throbbing
pain. Immediate treatment at a surgical emergency center is recommended.
FIRE
Leaks/ruptures in high pressure system using materials of this type can create a fire hazard when in the vicinity of ignition sources (eg.
open flame, pilot lights, sparks, or electric arcs).
FLAMMABLE PROPERTIES:
Flashpoint: (Cleveland Open Cup) 178 °C (352 °F) Minimum
EXTINGUISHING MEDIA: Use water fog, foam, dry chemical or carbon dioxide (CO2) to extinguish flames.
PROTECTION OF FIRE FIGHTERS:
Fire Fighting Instructions: This material will burn although it is not easily ignited. See Section 7 for proper handling and storage. For fires
involving this material, do not enter any enclosed or confined fire space without proper protective equipment, including self-contained breathing
apparatus.
Combustion Products: Highly dependent on combustion conditions. A complex mixture of airborne solids, liquids, and gases including
carbon monoxide, carbon dioxide, and unidentified organic compounds will be evolved when this material undergoes combustion.
ACCIDENTAL RELEASE MEASURES
Protective Measures: Eliminate all sources of ignition in vicinity of spilled material.
Spill Management: Stop the source of the release if you can do it without risk. Contain release to prevent further contamination of soil,
surface water or groundwater. Clean up spill as soon as possible. Use appropriate techniques such as applying non-combustible
absorbent materials or pumping. Where feasible and appropriate, remove contaminated soil. Place contaminated materials in disposable
containers and dispose of in a manner consistent with applicable regulations.
ECOLOGICAL INFORMATION
Waste disposal: In accordance with all environmental regulations applicable to your area.
Spillage: Prevent entry into drains, sewers and water course. Soak up with diatomaceous earth or other inert material. Store in
appropriate container for disposal.
Ecotoxocity: This material is expected to be harmful to aquatic organisms and may cause long-term adverse effects in
the aquatic environment. The ecotoxicity hazard is based on an evaluation of data for the components or a similar material.
HANDLING
Precautionary Measures: DO NOT USE IN HIGH PRESSURE SYSTEMS in the vicinity of flames, sparks and hot surfaces. Use only in
well ventilated areas. Keep container closed. Keep out of the reach of children.
General Handling Information: Avoid contaminating soil or releasing this material into sewage and drainage systems and bodies of
water.
Static Hazard: Electrostatic charge may accumulate and create a hazardous condition when handling this material. To minimize this
hazard, bonding and grounding may be necessary but may not, by themselves, be sufficient. Review all operations which have the
potential of generating and accumulating an electrostatic charge and/or a flammable atmosphere (including tank and container filling, splash
filling, tank cleaning, sampling, gauging, switch loading, filtering, mixing, agitation, and vacuum truck operations) and use appropriate
mitigating procedures.
DISPOSAL CONSIDERATIONS
Use material for its intended purpose or recycle if possible. Oil collection services are available for used oil recycling or disposal. Place
contaminated materials in containers and dispose of in a manner consistent with applicable regulations.
S/N: 3210 AND ABOVE
PLEASE CONTACT GAGE BILT FOR ALL OTHER SERIAL NUMBERS.
11
REV.11/14
GB752 - SELECTION CHART
FASTENER
COMMERCIAL LOCKBOLTS
MULTIGRIP LOCKBOLTS
BLIND BOLT (SINGLE ACTION)
WITH OR W/OUT DRIVE WASHER
MS90353S & U / MS90354S & U
MS21140S & U / MS21141S & U
CR7000 SERIES,
BACB30YY, YU, & YT
BLIND BOLT (SINGLE ACTION)
WITH DRIVE WASHER
MS90353S & U / MS90354S & U
MS21140S & U / MS21141S & U
CR7000 SERIES,
BACB30YY, YU, & YT
EN6122 & UAB130-EU
EN6127 & UAB6127-EU
EN6128 & UAB100-EU
EN6129 & UABP-EU
DIA.
STRAIGHT
*RIGHT ANGLE
**OFFSET
1
3/16
1/4
3/16
1/4
LB06-722-20
LB08-722-20
MG06-722-20
MG08-722-20
LB06-722-60
LB08-722-60
MG06-722-60
MG08-722-60
1/8
SB04-752C-20
SB04-752C-45
SB04-751B-54RA
SB04-752A-43OS
5/32
SB05-752C-20
SB05-752C-45
SB05-751B-54RA
SB05-752A-43OS
SB06-752B-45
SB06-751B-54RA
SB06-204D-27OS
SB05-752C-80
3/16
SB06-752B-20
SB06-752B-80
1/8
UBB04-752C-20
UBB04-752C-45
UBB04-751B-54RA
UBB04-752A-43OS
5/32
UBB05-752C-20
UBB05-752C-45
UBB05-751B-54RA
UBB05-752A-43OS
UBB06-752B-45
UBB06-751B-54RA
UBB06-204D-27OS
UBB05-752C-80
3/16
UBB06-752B-20
UBB06-752B-80
5/32
UBB05-752C-20
UBB05-752C-45
UBB05-751B-54RA
UBB05-752A-43OS
3/16
UAB06-752B-20
UAB06-752B-45
UAB06-751B-54RA
UAB06-752A-43OS
1/8
5/32
3/16
1/4
3/32
1/8
5/32
3/16
1/4
SMLS04-752C-20
SMLS05-752C-20
SMLS06-752B-20
SMLS08-713-20
3A-352B-25
4A-752C-20
5A-752C-20
6A-752B-20
SMLS08-713-20
SMLS04-752C-45
SMLS05-752C-45
SMLS06-752B-45
SMLS08-713-45
SMLS04-751B-54RA
SMLS05-751B-54RA
SMLS06-751B-54RA
SMLS04-752A-43OS
SMLS05-752A-43OS
SMLS06-752A-43OS
SMLS08-204D-27OS
4A-752C-45
5A-752C-45
6A-752B-45
3A-751B-54RA
4A-751B-54RA
5A-751B-54RA
6A-751B-54RA
3/32
3NP-751-23
3NP-352-61
3NP-751B-54RA
3NP-751-43OS
1/8
5N-751-23
5N-352-61
45N-751B-54RA
5N-751-43OS
EN6129 & UABP-EU
BLIND RIVET (SINGLE ACTION)
WITH OR W/OUT DRIVE WASHER
NAS1900 S & U SERIES
"A" CODE
NAS1398A & NAS1399A
NUT PLATE RIVETS
CCR244/264/274
BACR15DR
MS20600
CHERRYMAX®,
CHERRYMAX® 'AB',
MBC® LOCK CREATOR
BACR15FR/FP, BACR15GF/GK,
NAS1900 S & U SERIES BLIND
RIVET WITH DRIVE WASHER
4A-752A-43OS
5A-752A-43OS
6A-752A-43OS
SMLS08-204D-27OS
1/8
5/32
2
456MAX-751-23
2
456MAX-751A-61
2 456MAX-751D-54RA
2
456MAX-731-43OS
3/16
1/4
08MAX-752B-20
08MAX-752B-45
13/64
17/64
1/8
5/32
3/16
8/32
10/32
3/32
1/8
5/32
3/16
3/32
1/8
5/32
3/16
3/32
1/8
5/32
3/16
ASP06-752B-20
ASP08-752B-20
MBC04-752C-20
MBC05-752C-20
MBC06-752B-20
GS8-752B-20
GS10-752B-20
3N-751-23
4N-751-23
5N-751-23
6N-751-23
3N-751-23
4CEA-751-23
5CEA-751-23
6CEA-751-23
3N-751-23
4CES-751-23
5CES-751-23
6CES-751-23
ASP06-752B-45
ASP08-752B-45
MBC04-752C-45
MBC05-752C-45
MBC06-752B-45
GS8-752B-45
GS10-752B-45
3N-352-61
4N-352-61
5N-352-61
6N-352-61
3N-352-61
4CEA-352-61
5CEA-352-61
6CEA-352-61
3N-352-61
4CES-352-61
5CES-352-61
6CES-352-61
**08MAX-204D-27OS **08MAX-204D-37OS
ASP®
ASP 2, ASP PF, ASP 4 FF,
ASP 2 F, ASP 2 LC
NAS1719, NAS1720
NAS1721
GROUND STUD,
M83454 & BACS53B 4
OPEN END
NAIL RIVET
CLOSED END
NAIL RIVET
(ALUMINUM MANDREL)
CLOSED END
NAIL RIVET
(STEEL MANDREL)
ASP06-751B-54RA
MBC04-751C-54RA
MBC05-751C-54RA
MBC06-751C-54RA
GS8-751B-54RA
GS10-752A-54RA
3N-751B-54RA
45N-751B-54RA
45N-751B-54RA
6N-751C-54RA
3N-751B-54RA
45CEA-751B-54RA
45CEA-751B-54RA
6CEA-751C-54RA
3N-751B-54RA
45CES-751B-54RA
45CES-751B-54RA
6CES-751C-54RA
ASP06-752A-43OS
ASP08-752A-43OS
MBC04-752A-43OS
MBC05-752A-43OS
MBC06-752A-43OS
GS8-752A-43OS
GS10-752A-43OS
3N-751-43OS
4N-751-43OS
5N-751-43OS
6N-751-43OS
3N-751-43OS
4CEA-751-43OS
5CEA-751-43OS
6CEA-751-43OS
3N-751-43OS
4CES-751-43OS
5CES-751-43OS
6CES-751-43OS
CHERRYM AX®, T RIVET® AND M BC® ARE REGISTERED TRADEM ARKS OF CHERRY AEROSPACE FASTENERS. AVEX®, KLAM P-TITE®, TLR®, HEM LOK® AND M ONOBOLT® ARE REGISTERED
TRADEM ARKS OF AVDEL UK LIM ITED. ASP®, M AGNA-LOK® AND M AGNA-BULB® ARE REGISTERED TRADEM ARKS OF ALCOA INC. BULB-TITE® IS A REGISTERED TRADEM ARK OF GESIPA
FASTENERS USA, INC. ULTRA-GRIP® IS A REGISTERED TRADEM ARK OF EM HART TEKNOLOGIES.
GAGE BILT CERTIFIES THE GB752 WILL INSTALL THE ABOVE FASTENERS
PLEASE NOTE: Due to
**ALL OFFSET 204 SERIES NOSES REQUIRE 751204 ADAPTER.
lever assembly length,
1) RIGHT ANGLE NOSE ASSEMBLY'S MAY REQUIRE MORE THAN ONE PULL.
the GB752SR Tools
2) INSTALLS 1/8, 5/32 & 3/16 DIAMETERS
require -45 min. nose length
3) INSTALLS 5/32 & 3/16 DIAMETERS
for all straight noses.
*ALL RIGHT ANGLE NOSES REQUIRE 752142 STROKE LIMITER.
4) BACS53B -10 ONLY
NOTE: THE LAST 2 DIGITS OF THE NOSE ASSEMBLY REPRESENTS THE LENGTH THE NOSE EXTENDS FROM THE TOOL I.E. -20 = 2.0 INCHES
GB752SR MODELS MUST USE -45 LENGTH OR LONGER ON ALL 752 STYLE NOSES
Rev. 7/15
S/N: 3210 AND ABOVE
PLEASE CONTACT GAGE BILT FOR ALL OTHER SERIAL NUMBERS.
12
REV.11/14
GAGE BILT
DECLARATION OF CONFORMITY
MANUFACTURER: Gage Bilt Inc. 44766 Centre Ct. Clinton Twp. Michigan (586-226-1500)
WE DECLARE THAT THE EQUIPMENT SPECIFIED HEREIN CONFORMS
TO THE FOLLOWING DIRECTIVES AND STANDARDS
Machinery Directive 2006/42/EC
EN12100-1 & EN12100-2
EN792-1:2000+A1
EU REPRESENTATIVE: Edgar Hausmann GmbH Förster-Busch-Str. 10 D-34346 Hann. Münden Germany
EQUIPMENT DESCRIPTION: GB752 FASTENER INSTALLATION TOOL
This product specified above conforms to the above dIrectives and standards.
SIGNATURE:
NAME: BRIAN LEIGH
PRODUCT MANAGER
CLINTON TWP., MI U.S.A.
MAY 2010
(586) 226-1500
WARRANTY
Seller warrants that all goods covered by this catalog will conform
to applicable specifications and will replace or repair, F.O.B. our plant, any
goods providing defective from faulty workmanship, or material, for 6
months from date of shipment.
Said warranty to remain in effect if, and only if, such goods are
used in accordance with all instructions as to maintenance, operation and
use, set forth in manuals and instruction sheets furnished by seller.
Sellers obligation under this warranty shall be limited to the repair
or rework of the goods supplied or replacement thereof, at Seller’s option,
and in no case is to exceed the invoice value of said goods. Under no
circumstances will the seller be liable for incidental or consequential
damages or for damages incurred by the buyer or subsequent user in
repairing or replacing defective goods or if the goods covered by this
warranty are reworked or subjected to any type of additional processing.
This warranty is void if Seller is not notified in writing of any
rejections or defects within 6 months after the receipt of the material by the
customer.
THIS WARRANTY IS MADE IN LIEU OF ALL OTHER WARRANTIES
EXPRESSED OR IMPLIED, INCLUDING MERCHANTABILITY.
DEXRON® IS A REGISTERED TRADEMARK OF GENERAL MOTORS CORPORATION. LUBRIPLATE® IS A REGISTERED TRADEMARK OF FISKE BROTHERS REFINING CO. LOCTITE® IS A REGISTERED
TRADEMARK OF HENKEL CORPORATION.
S/N: 3210 AND ABOVE
PLEASE CONTACT GAGE BILT FOR ALL OTHER SERIAL NUMBERS.
13
REV.11/14
Download PDF
Similar pages