User’s Manual
Version 1.1
25-0462 - OMM-2500
Multi-format Modular
matrix
32x32 DVI / HDMI / SDI / DisplayPort Matrix
Doc No. : OM-D150512 / Rev1.1
TABLE OF CONTENTS
Chapter 1. Introduction and installation ................................................................................................ 4
1.1
Key features.............................................................................................................................4
1.2
Shipping group.........................................................................................................................5
1.3
Notice of safe usage................................................................................................................6
1.4
Physical description.................................................................................................................6
1.5
Installation................................................................................................................................7
1.5.1 Initialization ......................................................................................................................... 7
1.5.2 Connection for remote control ............................................................................................ 7
1.6
EDID Configuration..................................................................................................................7
Chapter 2. Control setup ....................................................................................................................... 9
2.1
TCP/IP.....................................................................................................................................9
2.1.1 TCP/IP setup of PC ............................................................................................................. 9
2.1.2 Launching Telnet ................................................................................................................ 9
2.2
RS-232..................................................................................................................................10
2.2.1 Launching HyperTerminal ................................................................................................. 10
Chapter 3. Control operation .............................................................................................................. 11
3.1
Home & State........................................................................................................................11
3.2
LINK mode.............................................................................................................................12
3.2.1 All Link............................................................................................................................... 13
3.2.2 All Unlink ........................................................................................................................... 13
3.3
Configuration mode...............................................................................................................14
3.3.1 Channel Name .................................................................................................................. 15
3.3.2 LAN & RS232 .................................................................................................................... 16
3.3.3 Multi Viewer ...................................................................................................................... 17
3.3.4 Video Generator ................................................................................................................ 18
3.3.5 Monitoring Port .................................................................................................................. 19
3.3.6 EDID Management ........................................................................................................... 20
3.3.7 HDCP on/off ...................................................................................................................... 24
3.3.8 Preset ................................................................................................................................ 25
3.3.9 Control Lock ...................................................................................................................... 28
Chapter 4. Control operation (Key button) .......................................................................................... 29
4.1
LINK mode.............................................................................................................................29
4.1.1 All Unlink ........................................................................................................................... 29
4.2
Configuration mode...............................................................................................................30
4.2.1 Channel Name .................................................................................................................. 31
4.2.2 LAN & RS232 .................................................................................................................... 32
4.2.3 Multi Viewer ...................................................................................................................... 32
4.2.4 Video Generator ................................................................................................................ 32
4.2.5 Monitoring Port .................................................................................................................. 32
4.2.6 EDID Management ........................................................................................................... 33
4.2.7 HDCP on/off ...................................................................................................................... 35
4.2.8 Control Lock ...................................................................................................................... 35
Chapter 5. PC program operation....................................................................................................... 36
5.1
PC program file download and Installation............................................................................36
5.2
Connect Info..........................................................................................................................37
2
Chapter 6. Web control panel operation ............................................................................................. 38
Chapter 7. Command input operation................................................................................................. 39
7.1
Command input structure......................................................................................................39
7.2
Examples of command inputs................................................................................................40
7.2.1 Link input and output ......................................................................................................... 40
7.2.2 Input and output status ..................................................................................................... 40
7.2.3 Input and Output Name request and setting ..................................................................... 41
7.2.4 Network setting ................................................................................................................. 41
7.2.5 Video generator setting ..................................................................................................... 42
7.2.6 Monitor output port setting ................................................................................................ 43
7.2.7 EDID control command ..................................................................................................... 44
7.2.8 HDCP On off setting ......................................................................................................... 44
7.2.9 Baud rate setting for RS-232 ............................................................................................ 45
7.2.10 Multi-viewer card (QDVI-O) setting ................................................................................... 45
7.2.11 Slot status request ............................................................................................................ 46
7.2.12 Control lock command ...................................................................................................... 47
7.2.13 Preset Control Commend ................................................................................................. 48
7.2.14 Power State Request ........................................................................................................ 49
7.2.15 Firmware Version Request ............................................................................................... 49
Chapter 8.
Firmware update ............................................................................................................... 50
Chapter 9.
Trouble shooting ............................................................................................................. 533
Chapter 10. Specification .................................................................................................................. 544
10.1 General
Specification.............................................................................................................544
10.2 Power
Specification...............................................................................................................555
10.3 SDI video input and output scailing condition........................................................................55
10.4 Compatibility between Dual link DVI In/Output cards and another
In/Output........................546
10.5 Compatibility between DisplayPort In/Output cards and another
In/Output...........................546
Chapter 11. Warranty Information .................................................................................................... 577
Chapter 12.
Safety Instructions ........................................................................................................ 588
Chapter 13.
Maintenance ................................................................................................................... 59
3
Chapter 1. Introduction and installation
Purpose
The modular matrix, OMM-2500 enables to connect between various video sources and displays and
it offers flexible installation with other video controllers or control software. The input and output cards
are composed of 4 ports, therefore user can easily configures any input and output channels from 4x4
to 32x32 by plugging the cards into OMM-2500 mainframe.
Introduction
The OMM-2500 modular matrix enables to switch up to 32 different DVI, HDMI, SDI, and DisplayPort
sources to 32 different digital displays. It can be configured using 8 input and output cards and each
card has 4 ports of input and output. In case of Dual link DVI card (DDVI-2EI / DDVI-2EO), it is
composed of 2 ports, therefore configuration for input and output channels are from 2x2 to 16x16.
Note) SDI is not a licensed HDCP interface and if the content received from HDMI is protected by
HDCP, there should be no output from the SDI slot.
1.1 Key features
▪ Up to 32 DVI, HDMI, SDI, and DisplayPort inputs and outputs can be configured.
▪ Each card has 4 input or 4 output ports and 8 cards can be fitted into input and output bays.

Dual link DVI supports from 2 x 2 to 16 x16 input and output.
▪ Has Electrical DVI, HDMI, SDI, DisplayPort and Optical DVI input and output cards.
▪ Provides Touch LCD and a user-friendly graphic interface.
▪ Complies with DDC/HDCP (Electrical DVI and HDMI cards only).
▪ Supports up to WUXGA (1920x1200) at 60Hz refresh ratio for Single link DVI, WQXGA
(2560x1600) at 60Hz refresh ratio for Dual link DVI and DisplayPort or 1080p at 60Hz for
HDMI and SDI.
▪ Supports 4 types of EDID management:

Default Mode.

Auto Detect Mode.

Output Copy Mode.

Resolution List Mode.
▪ Supports various control methods:

Touch control operation
4

Key buttons operation

Command input (Such as Hyper terminal by RS-232 and Telnet by TCP/IP)

Web panel control (TCP/IP)

PC program by RS-232 and UDP
▪ Works with OPTICIS DVI, HDMI, SDI, and DisplayPort optical extender for long signal
extension.
▪ Has dual-power supplier for hot-swappable and load-sharing.
▪ Equips multi-viewer card to be used in various monitoring systems.
▪ Provides Preset mode to save and load the current routings.
▪ Provides diagnostic function for quick trouble shooting.
▪ Has video generator output and monitoring output for easy installation.
1.2 Shipping group
▪ OMM-2500, Modular matrix chassis: 1 EA
▪ Input / output cards: Option













SDVI-4EI, 4 ports electrical Single link DVI input card
SDVI-4EO, 4 ports electrical Single link DVI output card
DDVI-2EI, 2 ports electrical Dual link DVI input card
DDVI-2EO, 2 ports electrical Dual link DVI output card
SDVI-1FI, 4 ports 1 fiber optical DVI input card
SDVI-1FO, 4 ports 1 fiber optical DVI output card
HDMI-4EI, 4 ports electrical HDMI input card
HDMI-4EI, 4 ports electrical HDMI output card
SDI-4EI, 4 ports electrical SDI input card
SDI-4EO, 4 ports electrical SDI output card
DP1-4EI, 4 ports electrical DisplayPort input card
DP1-4EO, 4 ports electrical DisplayPort output card
QDVI-O, Multi-viewer card
▪ AC power cord: 1EA
▪ Power supplier: 1 EA (Dual power supplier is an option)
▪ User manual: 1 EA
▪ Firmware download cable: 1 EA (Use only this accessory specified by the manufacturer)
▪ RS-232 cable (Straight type): 1 EA
5
1.3 Notice of safe usage
We recommend you to read following warning, precaution and information before start to
operate the OMM-2500 modular matrix.
▪ Use of the equipment in a manner not specified by the manufacturer may result in irecoverable damage.
▪ Keep the unit away from liquid, magnetic and combustible substances.
▪ Do not place heavy weight on the unit.
▪ Move away from noisy environment such as vibration or impact.
▪ Do not install the unit vertically. / Do not disassemble the unit.
▪ Carry the unit using the handle in front of the panel with two (2) Users.
1.4 Physical description
The OMM-2500 modular matrix chassis is mountable on a 19” standard rack. Key buttons,
LCD display and power switch are placed on the front panel as shown in Figure 1-1.
Figure 1-1 Front and Rear panel of OMM-2500
All Input and output cards, interface ports and power supplier are placed on the rear panel as
below.
▪ Input bay for 4 input cards (left side)
▪ Output bay for 4 output cards (right side)
▪ RS-232 / F1, Serial communication and Main Firmware port
▪ F2, Input Firmware port
▪ F3, output Firmware port
▪ LAN, RJ-45 receptacle for TCP/IP or UDP control
6
▪ REFERENCE OUTPUT for internal video source for easy installation
▪ MONITORING OUTPUT for internal output port to monitor input signal
▪ Power supplier (Dual-power is an option)
1.5 Installation
1.5.1 Initialization
▪ Put insert the cards into each input or output bay according to user interface.
▪ All input or output cards have the same connection way, and tighten the screws just until
snug against the main frame. Then, please make sure the cards are fully seated.
▪ Connect the provided AC power cord to AC power inlet. Turn on the switches at the bottom
of the AC power inlet and on the front panel step by step. Then, OMM-2500 will start
initialization process.
▪ ‘Loading’ will be shown on LCD display.
▪ After 7~10 sec, Home & State status on LCD display will be shown.
▪ Now, OMM-2500 is ready to receive commands from user.
1.5.2 Connection for remote control
▪ Connect the OMM-2500 to PC with the supplied RS-232 cable.
▪ Connect the OMM-2500 to PC with LAN cable with RJ-45 connector.
[NOTE] Typically, the IP address of PC connected to the network is configured by DHCP
server. But, if the PC is connected directly to the OMM-2500, the network server will
not able to assign the IP address. In this case, network information of PC should be
set manually.
The default IP address of OMM-2500 is 192.168.1.117. Before connecting OMM2500 to your network, please verify the availability of IP address in your network.
The IP address can be reconfigured by key button, PC program or command lines
over RS-232 or TCP/IP.
1.6 EDID Configuration
▪ EDID (Extended Display Identification Data) is an information set that is provided by a
display to describe its capabilities to a graphic source. It enables a graphic source to identify
the connected display.
▪ The information set includes: manufacturer, product type, phosphor or filter type, timings
supported by the display, display size, luminance data and (for digital displays only) pixel
7
mapping data.
▪ Once the graphic source reads the information set (usually during the booting process), the
EDID determines the optimal format for a connected display.
▪ OMM2500 supports storing of EDID information to an EEPROM for each Input.
▪ OMM2500 has four-way EDID settings, 1) Default Mode: default EDID from the factory, 2)
Output Copy Mode: read of EDID from any target display and copy in input port 3) Auto
Detect Mode: analyzing of all EDID from the attached displays and store optimized EDID in
input port to avoid any compliance problems in the field and 4) Resolution List Mode: read
EDID from the selected Resolution List by user and copies it in allocated input.
Displays
OUTPUT 1~32
Sources
INPUT 1~32
WRITE EDID
EEPROM1
EDID
EEPROM2
INTERFACE
CONTROL
EEPROM3
Read/Write
.
.
.
.
.
.
.
.
EEPROM32
Figure 1-2 Concept of EDID setting and working in OMM-2500 modular matrix
As depicted in Figure 1-2, once EDID is configured, each EDID is stored in EEPROM in Input
ports. As a result, the video sources are able to read EDID from the EEPROM during booting
process even though the OMM-2500 and connected displays are not powered on yet.
8
Chapter 2. Control setup
The OMM-2500 modular matrix can be controlled in various ways such as command input (RS-232,
TCP/IP), Web control panel (TCP/IP), supplied PC program (RS-232, UDP) as well as Touch LCD
and key button on the front panel. To do this, PC should be configured properly.
2.1 TCP/IP
2.1.1 TCP/IP setup of PC
TCP/IP, the abbreviation of Transmission Control Protocol (TCP) and the Internet Protocol (IP)
is commonly used protocol to control remote computers.
To control OMM-2500 over TCP/IP, set network properties of PC as below (Explained here is
based on Win 7 OS).
▪ Open Control Panel.
▪ Select Network Status in Network and Internet menu.
▪ Select Adapter setting.
▪ Select Local Area Connection and right click to open property.
▪ Select Internet Protocol Version 4 (TCP/IPv4)
▪ Enter IP, Subnet mask, Gateway and DNS server address, compatible with the current
network setting of OMM-2500.
▪ Click OK to terminate IP setup session.
[Note] If the IP address of OMM-2500 is 192.168.001.117, the PC IP address should be
chosen as 192.168.001.nnn; where ‘nnn’ can range from 000 to 255 except 117.
2.1.2 Launching Telnet
Telnet is a terminal program embedded in Window OS system to access remote computers
using TCP/IP protocol. With the network setting of the PC as above, launch Telnet as below.
▪ Make sure PC and OMM-2500 are connected by Ethernet.
▪ Click Start menu and select Run.
▪ Type CMD to open command window.
▪ Type ‘telnet 192.168.1.117’ (Type current IP address of OMM-2500).
9
▪ Press ENTER then, “==Welcome to OMM-2500==” and “== TELNET control ==”
messages will be shown.
▪ Type command inputs to control OMM-2500. (Refer to Chap. 7)
2.2 RS-232
2.2.1 Launching HyperTerminal
The OMM-2500 modular matrix provides RS-232 serial communication. The simplest way to
control OMM-2500 over RS-232 is using embedded software in Windows OS, HyperTerminal.
To launch Hyper Terminal (Explained here is based on Windows XP OS. Hyper Terminal is
not available on Win 7.):
▪ Connect the PC to OMM-2500 over RS-232 cable.
▪ Select Start > Programs > Accessories > Communications > HyperTerminal.
▪ Enter a name and choose an icon in Connection Description window and click OK.
▪ In Connect To window, ignore the Country, Area Code and Phone Number fields but select
available COM port of PC to be connected to OMM-2500 then, click OK.
▪ In COM Properties window, set the parameters as below:





Bits per second (baud rate): 115200 (115200 is default baud rate of OMM-2500)
Data bits: 8
Parity: None
Stop bits: 1
Flow control: None
[Note] Bit per second of Hyper Terminal should be set as same as baud rate of OMM-2500.
▪ Click OK to save the parameters.
▪ Go Start > Programs > Accessories > Communications > HyperTerminal, then new icon
will be shown. Then select it to launch Hyper Terminal.
▪ Type command inputs to control OMM-2500 (Refer to Chap. 7)
10
Chapter 3. Control operation
3.1 Home & State
▪ It provides a user-friendly graphic interface showing various status, such as input/output card
type, connection, power on/off, firmware version and network information.
▪ If the green LED of output slot number is lit ON as shown above, user can recognize the
resolution of input signal (ex. CH21=800x600) and input/output connection status.
▪ If LED is OFF, input and output signals are not connected and it will be disable as grey color.
▪ Description of Icons
Section
Remark
Section
Remark
Home & State icon
F/W MAIN
Current Firmware
version
Power Status icon
Sub-I
Current Input card
Firmware version
11
Link Mode icon
Sub-II
Current output card
Firmware version
Configuration Mode
icon
RS232,IP
Current Network
Setting status
3.2 LINK mode
▪
It configures input/output connections for cross-switching.
1) Touch
, the Link Icon.
2) Touch an input channel to be designated among 32 input buttons.
3) Touch single or multiple output channel(s) among 32 output buttons to be connected with
display.
4) Outputs can be initialized by clicking designated output button again.
5) Touch Apply button to save the configuration.
6) Touch the selected input button again to check current input number/channel name and
connected output.
7) To configure next Input / output connection, repeat from step 2 to 4.
12
3.2.1 All Link
▪
It connects an input and all output connection.
1) Touch All Link icon.
2) Touch an input channel button to select desired input.
3) Touch Apply button to save the configuration.
4) Touch selected input channel again to check the connection between the selected input
and connected all output.
3.2.2 All Unlink
▪
It unlinks connected input and output channel(s).
1) Touch All Unlink button.
2) Touch an input channel button to select desired input.
3) Touch Apply button to save the configuration.
4) Touch the selected input channel again to check an unlink state between the selected input
and connected output(s).
13
3.3 Configuration mode
▪
It provides basic configuration of OMM-2500.
▪
Touch









, configuration icon to see all features.
Channel Name
LAN & RS232
Multi-Viewer (It is activated when QDVI-O is in output bay)
Video Generator
Monitoring Port
EDID Management
HDCP on/off
Preset
Control Lock
14
3.3.1 Channel Name
▪ It can be allocated specific names for all inputs and outputs to distinguish them.
▪ Touch Input channel or Output Channel bar right next to Channel Name.
▪ Touch a channel bar to enter channel name.
▪ Then, the keypad window will be popped up.
▪ Touch Shift key to select a letter or number and ‘0’ button to make a space.
▪ Enter a channel name using the keypad.
▪ Touch Enter key, then keypad will be closed.
▪ Touch the Save button to complete the process.
15
3.3.2 LAN & RS232
1)
Baud rate:
▪ It sets RS-232 Baud Rate. OMM-2500 supports 9600, 19200, 38400, 57600 and 115200bps.
▪ Touch
icon to decrease Baud Rate.
▪ Touch
icon to increase Baud Rate.
▪ Touch Apply icon to complete the process.
▪ The default setting is 115200.
2)
Network:
▪ It modifies IP Address, Subnet mask, Gateway, Mac Address and Port to be used for your
network.
▪ Touch one (1) of them to modify the network setting.
▪ LED shows the keypad window.
▪ Touch the number key to enter desired setting.
▪ Touch the Shift icon to move the next row.
16
▪ Touch
the icon to modify the number.
▪ Touch the Enter key.
▪ Touch the Apply icon to save the configuration.
▪ The Network default setting is as below.
- IP Address: 192.168.001.117
- Subnet Mask: 255.255.255.000
- Gateway: 192.168.001.001
- UDP Port: 3000
3.3.3 Multi Viewer
▪ The most outstanding feature of OMM-2500 is embedded multi-viewer card, QDVI-O.
▪ Multi-viewer card, QDVI-O can choose 4 inputs among 32 inputs of OMM-2500 and
configure and output these input signals with 7 different layouts.
▪ Select the SLOT No. by touching
icon. It shows location where the QDVI-O is
inserted among output slots. If only one QDVI-O is inserted the number will be fixed and not
changed.
17
▪ Select the output resolution by touching
icon.
▪ Touch the Full Window or Divided Window icon.
▪ Touch the Apply icon to complete the process.
3.3.4 Video Generator
▪ It changes resolution and pattern of video generator.
▪ Select resolution or pattern and OSD by touching the icons.
▪ Touch Apply icon to complete the process.
18
3.3.5 Monitoring Port
▪ It allocates input to Monitor Output port for monitoring uses.
▪ Connect a display to the Monitoring Output port and any video sources to the DVI input ports
on the real panel.
▪ Touch an input channel to select desired input.
▪ Touch the Apply icon to complete the process.
19
3.3.6 EDID Management
▪ It sets EDID information of display in input port.
▪ OMM-2500 supports four (4) types of EDID setting: Default Mode, Auto detect Mode, Output
Copy Mode and Resolution List Mode for supporting easier installation with various displays
in the field.
1)
Default Mode
▪ It is default EDID from the factory. By selecting it, default EDID will be designated for
allocated input channels.
▪ Check the Default icon by touch.
▪ Touch single or multiple input channel icons to select desired inputs
▪ Touch the Apply icon to complete the process.
▪ Start the Default EDID writing process.
Report shows the progress status. For example, if user select three (3) and four (4) input
channel icons, “Default EDID Write Process Start”, “Input 3: Default EDID Mode” and “Input 4:
20
Default EDID Mode” are shown in Report box.
2)
Auto detect Mode
▪ It analyzes all EDID of attached displays at the output ports of OMM-2500 and get optimized
EDID. By selecting it, user can save optimized one in allocated input.
▪ Touch the Auto detect icon.
▪ Touch single or multiple input channel icons to select desired inputs
▪ Touch the Apply icon to complete the process.
▪ Start the Auto detect EDID writing process.
▪ Report shows the progress status. For example, if user select nine (9) and ten (10) input
channel icons, Report shows;
“AutoMix EDID Write Process Start”, “Input 9: Automix EDID Mode” and “Input 10: Automix
EDID Mode”.
3)
Output Copy Mode
▪ It reads EDID from any target display and copies it in allocated input.
▪ Touch the Output Copy icon.
▪ Select the “OUTPUT 00” combo box right next to the Output Channel to designate output
channel.
21
▪ Then, the keypad window will be shown as above.
▪ Enter the number of desired output channel by select number keys.
▪ Touch Enter and Close.
▪ Then, previous page with 1~32 buttons will be shown.
▪ Touch single or multiple input channel icons to select desired inputs.
▪ Touch the Apply icon to complete the process.
▪ Start Output EDID writing process.
▪ Report shows the progress status. For example, if user select one (1) output channel and
nine (9), ten (10) input channel icons, Report shows step by step as below;
“Output EDID Write Process Start”, “Output 1 Data Read Start”, “Output 1 Data Read
Success!!”, “Input 9: Out 30 Copy EDID Mode” and “Input 10: Out 30 Copy EDID Mode”
22
4)
Resolution List
▪ It reads EDID from the selected Resolution List by user and copies it in allocated input.
▪ Touch the
icon to select the desired resolution. The Resolution List is as below;
SVGA
(800x600)
XGA
(1024x768)
720P
(1280x720)
WXGA
(1366x768)
SXGAp
(1400x1050)
UXGA
(1600x1200)
WSXGAP
(1680x1050)
1080P
(1920x1080)
WUXGA
(1920x1200)
2K
(2048x1080)
▪ Touch single or multiple input channel icons to select desired inputs.
▪ Touch the Apply icon to complete the process.
▪ Start the Resolution List EDID writing process.
▪ Report shows the progress status.
23
WXGAp
(1440x900)
3.3.7 HDCP on/off
▪ User can set HDCP on/off in this menu.
▪ Select (Deselect) single or multiple Input Channel icons by touching.
▪ Touch the Apply icon to complete the process.
[Note] Only the Electrical single link DVI, Dual link DVI and HDMI cards complies with HDCP.
24
3.3.8 Preset
▪ It saves and loads the current routings to up to ten (10) specified preset number.
1)
Preset Save mode
▪ Touch the Save icon.
▪ Touch the
icon to select desired Preset Save number.
25
▪ Touch the Edit icon to modify or enter a Preset name.
▪ Then, key pad will be shown as above.
▪ Touch the Shift key to select a letter or number.
▪ Touch a letter or number key to enter a desired Preset name.
▪ Touch “0” key to make a space and enter next letter. For example, if user want to enter ‘AB’,
touch “A”, “0” and “B” keys in order.
▪ Touch ENTER key to save the name.
▪ Touch an input channel icon to select desired input.
▪ Touch single or multiple output channel icons to select desired outputs.
▪ Outputs can be deselected by touching each output channel icon again.
▪ Touch Save icon to save the configuration.
Touch the selected input channel icon again and it shows current input / output connection
26
2)
Preset Load mode
▪ Touch the Load icon.
▪ Touch the
icon to select desired Preset Load number.
▪ Touch the Load icon, next to the icon, such as
input / output connection in the Preset Load number
and it shows current
▪ Touch the Apply icon to complete the process.
[Note] Saved input / output connection data in the Preset Save number is also saved in the
Preset Load number at the same time.
27
3.3.9 Control Lock
1)
Lock
▪ It locks and unlocks control items such as Web, Key, RS-232, TCP/IP and UDP.
▪ Select the Lock or Unlock by touching the icon.
▪ Touch the Apply icon to complete the process.
2)
Reset
▪ It resets OMM-2500 by system reboot and default setting. It maintains the latest link
connection and network.
▪ Touch the Reset icon to complete the process.
28
Chapter 4. Control operation (Key button)
4.1 LINK mode
▪
It configures input/output connections for cross-switching.
1) Press LINK key button. Then, the blue led in the both LINK key button and number key
button will be turned on.
2) Press an input channel key button to select desired input. To select an input channel,
please press two (2) digit number such as 01, 02.. 07.
3) Press ENTER key button. Then, the green led in the number key button will be turned on to
select output channel(s).
4) Press single or multiple output channel(s) to select desired outputs.
5) Outputs can be deselected by pressing the each output key button again.
6) Press ENTER key button.
7) To configure next input / output connection, repeat 2 to 6.
8) To save the configuration, Press LINK key button and select Apply icon on the screen.
To cancel the configuration, Press LINK key button and select Cancel icon on the screen.
9) Press ENTER key button to save the configuration.
4.1.1 All Unlink
▪
It unlinks connected input and output channel(s).
1) Press SHIFT and LINK key button step by step.
2) Press an input channel key button to select desired input.
3) To save the configuration, Press LINK key button and select Apply icon on the screen.
To cancel the configuration, Press LINK key button and select Cancel icon on the screen.
4) Press ENTER key button to save the configuration.
29
4.2 Configuration mode
▪
It provides basic configuration of OMM-2500.
▪
Press FUNC key button and select the mode as below.









Channel Name
LAN & RS232
Multi-Viewer (It is activated when QDVI-O is in output bay)
Video Generator
Monitoring Port
EDID Management
HDCP on/off
Preset
Control Lock
4.2.1 Channel Name
▪
It can be allocated specific names for all inputs and outputs to distinguish them..
1) Press FUNC key button to select Channel Name icon.
2) Press ENTER key button.
3) Press an input channel key button to enter desired channel name.
4) Press ENTER key button. Then, the keypad window will be popped up.
5) Enter a channel name using the key button. If you want to enter the number, please press
SHIFT key button.
6) Press ENTER key button.
7) To enter next input channel name, repeat 3 to 6.
8) To save the channel name, Press FUNC key button and select Save icon on the screen.
To cancel the channel name, Press FUNC key button and select Cancel icon on the screen
9) Press ENTER key button to complete the process.
10) Press FUNC key button to move and enter an output channel name.
11) To enter output channel name, repeat 3 to 9 such as input channel name.
12) Press ESC key button, if you want to back to Configuration mode.
30
4.2.2 LAN & RS232
* Baud rate:
▪ It sets R-232 Baud Rate. OMM-2500 supports 9600, 19200, 38400, 57600 and 115200bps.
1) Press FUNC key button to select LAN & RS232 icon.
2) Press ENTER key button.
3) Press number 4 key button to decrease Baud Rate.
4) Press number 6 key button to increase Baud Rate.
▪ The default setting is 115200.
* Network:
▪ It modifies IP Address, Subnet mask, Gateway, Mac Address and Port to be used for your
network.
1) Select the network using FUNC key button.
2) Press ENTER key button. Then, the keypad window will be popped up.
3) Press the number key button to enter the desired number.
4) Press SHIFT key button to move the next row.
5) Press ENTER key button.
6) To save the network, Press FUNC key button and select Apply icon on the screen.
To cancel the network, Press FUNC key button and select Cancel icon on the screen
7) Press ENTER key button to complete the process.
▪ The Network default setting is as below.
- IP Address: 192.168.001.117
- Subnet Mask: 255.255.255.000
- Gateway: 192.168.001.001
- UDP Port: 3000
▪ The section can be moved pressing FUNC key button.
31
4.2.3 Multi Viewer
▪
▪
The most outstanding feature of OMM-2500 is embedded multi-viewer card, QDVI-O.
Multi-viewer card, QDVI-O can choose 4 inputs among 32 inputs of OMM-2500 and configure
and output these input signals with 7 different layouts.
1) Press FUNC key button to select Multi-viewer icon.
2) Press ENTER key button.
3) Select the section using FUNC key button.
4) Press number 4 and 6 key button to select the desired type.
5) To save the type, Press FUNC key button and select Apply icon on the screen.
To cancel the type, Press FUNC key button and select Cancel icon on the screen.
6) Press ENTER key button to complete the process.
4.2.4 Video Generator
▪
It changes resolution and pattern of video generator.
1) Press FUNC key button to select Video generator icon.
2) Press ENTER key button.
3) Select the section using FUNC key button.
4) Press number 4 and 6 key button to select the desired type.
5) To save the type, Press FUNC key button and select Apply icon on the screen.
To cancel the type, Press FUNC key button and select Cancel icon on the screen.
6) Press ENTER key button to complete the process.
4.2.5 Monitoring Port
▪ It allocates input to Monitor Output port for monitoring uses.
▪ Connect a display to the Monitoring Output port and any video sources to the DVI input ports
on the real panel.
1) Press FUNC key button to select Monitoring Port icon.
2) Press ENTER key button.
3) Press an input key button to monitor desired input channel.
4) To save the monitoring port, Press FUNC key button and select Apply icon on the screen.
To cancel the monitoring port, Press FUNC key button and select Cancel icon on the
screen.
5) Press ENTER key button to complete the process.
32
4.2.6 EDID Management
▪ It sets EDID information of display in input port.
▪ OMM-2500 supports four (4) types of EDID setting: Default Mode, Auto detect Mode, Output
Copy Mode and Resolution List Mode for supporting easier installation with various displays
in the field.
▪ The modes can be saved at the same time after selecting each mode.
* Default Mode
▪ It is default EDID from the factory. By selecting it, default EDID will be designated for allocated
input channels.
1) Press FUNC key button to select EDID Management icon.
2) Press ENTER key button.
3) Select the section using FUNC key button.
4) Press single or multiple input channel key buttons to select desired inputs
5) To save the Default Mode, Press FUNC key button and select Apply icon on the screen.
To cancel the Default Mode, Press FUNC key button and select Cancel icon on the screen.
6) Press ENTER key button to complete the process.
7) Start the Default EDID writing process.
Report shows the progress status. For example, if user select three (3) and four (4) input
channel icons, “Default EDID Write Process Start”, “Input 3: Default EDID Mode” and “Input 4:
Default EDID Mode” are shown in Report box.
* Auto detect Mode
▪ It analyzes all EDID of attached displays at the output ports of OMM-2500 and get optimized
EDID. By selecting it, user can save optimized one in allocated input.
1) Select the section using FUNC key button.
2) Press single or multiple input channel key buttons to select desired inputs
3) To save the Auto detect Mode, Press FUNC key button and select Apply icon on the
screen.
To cancel the Auto detect Mode, Press FUNC key button and select Cancel icon on the
screen.
4) Press ENTER key button to complete the process.
5) Start the Default EDID writing process.
.
Report shows the progress status. For example, if user select nine (9) and ten (10) input
channel icons, Report shows;
“AutoMix EDID Write Process Start”, “Input 9: Automix EDID Mode” and “Input 10: Automix
EDID Mode”.
33
* Output Copy Mode
▪ It reads EDID from any target display and copies it in allocated input.
1) Select the section using FUNC key button.
2) Press ENTER key button. Then, the keypad window will be shown.
3) Press output channel key button.
4) Press ENTER key button. Then, the keypad window will be closed.
5) Press single or multiple input channel key buttons to select desired inputs
6) To save the Auto detect Mode, Press FUNC key button and select Apply icon on the
screen.
To cancel the Auto detect Mode, Press FUNC key button and select Cancel icon on the
screen.
7) Press ENTER key button to complete the process.
8) Start the Output EDID writing process.
.
Report shows the progress status. For example, if user select one (1) output channel and nine
(9), ten (10) input channel icons, Report shows step by step as below;
“Output EDID Write Process Start”, “Output 1 Data Read Start”, “Output 1 Data Read
Success!!”, “Input 9: Out 30 Copy EDID Mode” and “Input 10: Out 30 Copy EDID Mode”
* Resolution List
▪ It reads EDID from the selected Resolution List by user and copies it in allocated input.
1) Select the section using FUNC key button.
2) Press number 4 and 6 key button to select the desired resolution. The Resolution List is as
below;
SVGA
(800x600)
XGA
(1024x768)
720P
(1280x720)
WXGA
(1366x768)
SXGAp
(1400x1050)
UXGA
(1600x1200)
WSXGAP
(1680x1050)
1080P
(1920x1080)
WUXGA
(1920x1200)
2K
(2048x1080)
3)
6)
7)
8)
WXGAp
(1440x900)
Press single or multiple input channel key buttons to select desired inputs
To save the Auto detect Mode, Press FUNC key button and select Apply icon on the
screen.
To cancel the Auto detect Mode, Press FUNC key button and select Cancel icon on the
screen.
Press ENTER key button to complete the process.
Start Resolution List EDID writing process.
Report shows the progress status.
34
4.2.7 HDCP on/off
▪
User can set HDCP on/off in this menu.
1) Press FUNC key button to select HDCP on/off icon.
2) Press ENTER key button.
3) Select (Deselect) single or multiple input channel by pressing number key button.
4) To save HDCP, Press FUNC key button and select Apply icon on the screen.
To cancel HDCP, Press FUNC key button and select Cancel icon on the screen.
5) Press ENTER key button to complete the process.
[Note] Only the Electrical single link DVI, Dual link DVI and HDMI cards complies with HDCP.
4.2.8 Preset
▪
Control operation of key button is not supported Preset mode.
4.2.9 Control Lock
* Lock:
▪ It locks and unlocks control items such as Web, Key, RS-232, TCP/IP and UDP.
1) Press FUNC key button to select Control Lock icon.
2) Press ENTER key button.
3) Select the section using FUNC key button.
4) Press number 4 and 6 key button to select Lock or Unlock
5) To save the Lock, Press FUNC key button and select Apply icon on the screen.
To cancel the Lock, Press FUNC key button and select Cancel icon on the screen.
6) Press ENTER key button to complete the process.
* Reset:
▪ It resets OMM-2500 by system reboot and default setting. It maintains the latest link
connection and network.
1) Select the Reset using FUNC key button.
2) Press number 4 and 6 key button to select Reset.
3) To save the Reset, Press FUNC key button and select Apply icon on the screen.
To cancel the Reset, Press FUNC key button and select Cancel icon on the screen.
4) Press ENTER key button to complete the process.
35
Chapter 5. PC program operation
The PC program with a user-friendly graphic interface is configured same as touch screen on front
panel.
5.1 PC program file download and Installation
▪ Visit our website, www.opticis.com.
▪ Click PRODUCTS bar at the top of the page.
▪ Click Multi-format Matrix Router and OMM-2500 step by step.
▪ Click and download the PC program file.
▪ Run the setup.exe to install OMM-2500 PC program.
The OMM-2500 icon will be shown on the wallpaper. Double click it to launch PC program and will be
shown as below.
Fig 5-1 PC program of OMM-2500
36
5.2 Connect Info
▪
▪
▪
▪
Move the mouse cursor at the top of the black bar.
Click the right mouse button and select “Setting” to set the control.
Select the way of control method between RS-232 and UDP(Ethernet).
In case of RS-232 control, enter available COM port number of your PC and select baud
rate. The baud rate should be same as that OMM-2500. (115200 is default)
▪ In case of Ethernet, enter IP address of OMM-2500 and port number. 3000 is default port
number of OMM-2500.
▪ Click Open button to finish the setting.
▪ If the connection is properly made, current status of OMM-2500 will be shown.
[NOTE] Click the right mouse button at the top of the black bar and select “Refresh” to
update the current status, if it’s necessary.
[NOTE] Click the right mouse button at the top of the black bar and select “Show Log Handler”
to check the current command status, if it’s necessary. Then, the Message window
will be shown.
37
Chapter 6. Web control panel operation
The Web control panel operation provides a user-friendly graphic interface and easy access to control
OMM-2500, if the PC is connected to Ethernet. But the functions are a little bit limited comparing with
other methods.
The OMM-2500 supports standard web browser but Microsoft Explorer is highly recommended to run
OMM-2500 stably. Before running the web browser to control OMM-2500, please confirm that Network
setting of OMM-2500 and Ethernet connection of the PC (Refer to Chap 2 and Chap 3).
Launch the web browser and enter the IP address of current OMM-2500 into the URL address line.
For example, if the IP address of OMM-2500 is set as 192.168.001.117, just type 192.168.1.117.
Fig 6-1 Web control panel
Fig 6-1 shows structure of Web control panel. It controls input / output connection and vide generator
and informs simple input / output status. Please remind that after new input /output connection, user
38
has to click LINK button and SEND button for new generator setting.
Chapter 7. Command input operation
The OMM-2500 modular matrix could be operated with various interfaces such as Touch LCD, key
button inputs, command input through RS-232 and TCP/IP, Web control through TCP/IP and PC
program through RS-232 and UDP. All functions are executed on a basis of a serial command input,
but the graphic interfaces on the Web or the PC program make more efficient way to operate the
OMM-2500 modular matrix. Command input operation is accomplished through RS-232 or TCP/IP.
For setting procedures for those protocols, please refer to Chap 2 and Chap 3.
7.1 Command input structure
The command inputs are composed of a string of ASCII codes and its basic structure is;
Command + Delimiter (‘=’) + Data + Delimiter (‘^’ or ‘,’ or ‘_’) + Data + End (‘!’)
Table 7.1 shows all commands and its brief descriptions
Command
Description
LINK
Input and Output connection
IN
Input signal status request
OUT
Output signal status request
INNAME
Input Channel Name Request and setting
OUTNAME
Output Channel Name Request and setting
NET
Network information request
NETGW
Gateway address setting
NETSN
Subnet mask address setting
NETIP
IP address setting
NETPA
MAC address setting
NETPT
UDP port number setting
VID
Video generator status request
VIDRES
Video generator resolution setting
VIDIMG
Video generator pattern setting
MON
Monitoring port setting and status request
EDID
EDID mode setting
HDCP
HDCP On/Off request and setting
RS232
RS-232 Baud rate request setting
QUAD
Quad-viewer card status request
QUADRES
Quad-viewer card output resolution setting
QUADLAY
Quad-viewer card layout setting
PRE
Preset Load and save
PRENAME
Preset name request and Setting
SLOT
Input output slot status request
LOCK
Lock/Unlock the control type
PWR
SMPS Power On/Off State Request
VER
MAIN In Out Firmware Version Request
39
Table 7.1 Commands set
▪ The command input allows executing only one command. Multiple command inputs require
executing multiple strings having each command per a string.
▪ User can use capital letters and small letters for commands but cannot mix it like ‘Link’, it
must be corrected as ‘link’ or ‘LINK’.
▪ After all input commands, OMM-2500 sends back replies to conform the execution of
commands.
▪ Input and output port number range from 1 to 32 and prefix, ‘0’ can be used such as ‘001’
and ‘010, but in the replies after the command inputs, the digits of port number are two such
as ‘01’ and ‘10’.
7.2 Examples of command inputs
7.2.1 Link input and output
▪ It makes single or multi-connections of inputs and outputs.
▪ It makes disconnection of all inputs when used with ‘0’.
▪ It requests inputs and outputs status of OMM-2500.
Command
LINK=01^10!
LINK =1^03,04^7!
Description and reply
Makes input 1 connected to output 10.
Reply: LINK=01^10!
Makes input 1 connected to output 3 and 4 to 7.
Reply: LINK =01^03,04^07!
LINK =05!
Makes input 5 connected to all outputs.
Reply: LINK=05!
LINK =00!
Makes all connections disconnected.
Reply: LINK =00!
LINK =00^06!
Link=?!
Makes output 6 disconnected.
Reply: LINK =00^06!
Requests current inputs and outputs connections status.
Reply: LINK =01^01,02^04,~32^13!
Table 7.2 Link command examples
7.2.2 Input and output status
▪ It requests input signal status. If the input is connected, it replies input resolution, but if it is
not connected, it returns ‘Signal Off’.
▪ It requests output status whether it is connected to display or not.
Command
IN=05!
Description and reply
Requests input 5 status.
Reply: IN=[05]1920x1200p! or IN=[05]Signal Off!
40
Requests output 12 status.
Reply: OUT=[12]Un Plugged! or OUT=[12]Plugged!
OUT=12!
Table 7.3 Input and output status command examples
7.2.3 Input and Output Name request and setting
Command
Description and reply
Requests input 5 name
Reply: INNAME=[05]MATRIX_IN05!
INNAME=05!
INNAME=05_DVDPlayer!
Setting input 5 name
Reply: INNAME=[05]DVDPLAYER!
Requests output 12 name
Reply: OUTNAME=[12]MATRIX_OUT12!
OUTNAME=12!
OUTNAME =12_project01!
Setting input 5 name
Reply: OUTNAME =[12]PROJECT01!
Table 7.4 Input and Output Name request and setting command examples
7.2.4 Network setting
▪ It sets IP, Gateway, Subnet mask, MAC address and UDP port number.
▪ It requests current network setting.
Command
Description and reply
NETGW=192.168.1.1!
NETIP=192.168.1.118!
NETSN=255.255.255.0!
Sets Gateway address, each data ranges from 000 to 255.
Reply: NETGW=192.168.001.001!
Sets IP address, each data ranges from 000 to 255.
Reply: NETGW=192.168.001.118!
Sets Subnet mask address, each data ranges from 000 to 255.
Reply: NETSN=255.255.255.000!
NETPA=AA.BB.CC.DD.EE.FF!
Sets MAC address, each data ranges from 00 to FF.
Reply: NETPA= AA.BB.CC.DD.EE.FF!
NETPT=3000!
Sets UDP port number, data ranges from 0 to 65535.
NETPT=3000!
NET=?!
Requests current network setting.
Reply: NETGW=192.168.001.001!
NETIP=192.168.001.118!
NETSN=255.255.255.000!
NETPA=AA.BB.CC.DD.EE.FF!
NETPT=3000!
Table 7.5 Network setting command examples
41
7.2.5 Video generator setting
▪ It changes resolution and pattern of video generator.
▪ It requests current video generator setting.
Table 7.6 describes the resolutions and patterns OMM-2500 supports. By command input
operation, user can change these to be used with on-site source for easy installation
Data #
Resolution
Pattern
1
800x600@60Hz
Vertical Color Bar
2
1024x768@60Hz
Vertical Color Bar scroll (Interval:0.5sec)
3
1280x960@60Hz
Vertical Color Bar scroll (Interval:1.0sec)
4
1280x1024@60Hz
Horizontal Color Bar
5
1600x1200@60Hz
Horizontal Color Bar scroll (Interval:0.5sec)
6
1920x1200@60Hz
Horizontal Color Bar scroll (Interval:1.0sec)
7
1280x720p@60Hz
Full White
8
1920x1080i@60Hz
Full Yellow
9
1920x1080p@60Hz
Full Cyan
10
Full Green
11
Full Magenta
12
Full Red
13
Full Blue
14
Full Gray
15
Cross Hatch 16x16
16
Grayscale bars
Table 7.6 Video generator resolutions and patterns
42
Command
Description and reply
VIDRES=4!
Sets video generator resolution by data #4.
Reply: VIDRES=1280x1024@60HZ!
VIDIMG=3!
Sets video generator pattern by data #3.
Reply: VIDIMG=VCOLORBAR10SMOVE!
VIDOSD=1!
VID=?!
Sets Video generator OSD On.
Reply : VIDOSD=ON!
* OSD Off is ‘0’
Requests current video generator resolution and pattern.
Reply: VID=04_03_01!
(it means data #4 resolution and data #3 pattern and OSD
On)
Table 7.7 Video generator command examples
7.2.6 Monitor output port setting
▪ It makes input to connected to monitor output port.
▪ It requests current input port that connected to monitor output port.
Command
Description and reply
MON=13!
Makes input 13 connected to monitor output ports.
Reply: MON=13!
MON=?!
Requests current input port that connected to monitor output port.
Reply: MON=13!
Table 7.8 Monitor output setting command examples
43
7.2.7 EDID control command
▪ It stores EDID information in input port of OMM-2500.
▪ It requests current EDID setting for all input ports.
Command
Description and reply
Default mode: Saves default EDID in input ports 1, 7 and 15.
Reply: EDID=01DEF.!
EDID=07DEF.!
EDID=15DEF.!
EDID=DE1,7,15!
EDID=AUTO2,8,9!
Auto mix mode: Analyzes all EDID information of connected displays to
makes optimized EDID then save it in input ports 2, 8 and 9.
Reply: EDID=02AUTO!
EDID=08AUTO!
EDID=09AUTO!
EDID=OUT3_5!
Output copy mode: Copies EDID information of output 3 display and
stores it in input port 5.
Reply: EDID=03OUT.!
Resolution EDID Mode : Save Resolution list 3 to input 32
Reply : EDID=32RES.!
EDID=RES03_32!
Requests current EDID setting for all inputs.
Reply: EDID=01OUT.02AUTO03RES.~32DEF.!
EDID=?!
Table 7.9 Monitor output setting command examples
7.2.8 HDCP On off setting
▪ Only the Electrical single link DVI, Dual link DVI and HDMI cards complies with HDCP.
Command
Description and reply
HDCP=32OFF!
HDCP=?!
Sets HDCP OFF Input 32
Reply: HDCP=[32]OFF!
* HDCP ON is ‘ON’
Requests current All Input HDCP State
Reply: HDCP=01ON,02OFF,~31ON,32OFF!
Table 7.10 HDCP ON off setting command examples
44
7.2.9 Baud rate setting for RS-232
▪ It sets RS-232 baud rate. OMM-2500 supports 9600, 19200, 38400, 57600, 115200bps.
▪ It requests current RS-232 baud rate.
Command
Description and reply
RS232=115200!
Sets RS-232 baud rate.
Reply: RS232=115200BPS!
RS232=?!
Requests current baud rate.
Reply: RS232=115200BPS!
Table 7.11 Baud rate setting command examples
7.2.10 Multi-viewer card (QDVI-O) setting
▪ It sets output resolution and layout of QDVI-O.
▪ It requests current status of QDVI-O.
Data #
Resolution
Layout
1
800x600@60Hz
1 input of QDVI-O on a full screen
2
1024x768@60Hz
2 input of QDVI-O on a full screen
3
1280x960@60Hz
3 input of QDVI-O on a full screen
4
1280x1024@60Hz
4 input of QDVI-O on a full screen
5
1600x1200@60Hz
Quad-screen
6
1920x1200@60Hz
1 Large screen (Left side) + 3 Small screen (Right side)
7
1280x720p@60Hz
1 Large screen (Top side) + 3 small screen (Bottom side)
8
-
-
9
1920x1080p@60Hz
-
st
nd
rd
th
Table 7.12 Supporting resolutions and layouts of QDVI-O
45
The first numeric data in command line represents slot number of output bay of OMM-2500
where QDVI-O is inserted.
Command
Description and reply
QUADRES=3_9!
Sets output resolution of QDVI-O at 1920x1080P. In this case,
rd
QDVI-O is inserted in 3 slot of output bay.
Reply: QUADRES=03_09!
QUADLAY=1_5!
Sets layout of QDVI-O as quad-screen. In this case, QDVI-O is
st
inserted in 1 slot of output bay.
Reply: QUADLAY=01_05!
QUAD=?!
Request current status of QDVI-O. If one QDVI-O is inserted in 2
slot and output resolution is 1600x1200@60Hz with layout #6:
Reply: QUAD=01_00_00,02_05_06,03_00_00,04_00_00!
nd
Table 7.13 Multi-viewer card setting command examples
7.2.11 Slot status request
▪ It requests current cards type in input and output bay.
Data
Card type
Data
Card type
02
Single DVI input card, SDVI-4EI
12
SDI input card, SDI-4EI
03
Single DVI output card, SDVI-4EO
13
SDI output card, SDI-4EO
18
1 Fiber DVI input card, SDVI-IFI
0C
DisplayPort input card, DP1-4EI
19
1 Fiber DVI output card, SDVI-1FO
0D
DisplayPort output card, DP1-4EO
21
Multi-viewer card, QDVI-O
1A
Reserved
0A
HDMI input card, HDMI-4EI
1B
Reserved
0B
HDMI output card, HDMI-4EO
-
Table 7.14 Card types and its data
46
The first numeric data in reply represents the order row of slot and second and third data
represents type of input and output cards.
Command
SLOT=?!
Description and reply
Requests current cards type in input and output bay.
OMM-2500 has 8 rows of input and output slots. If the input output
cards are configured as below:
st
1 row: Single DVI input card / 1 Fiber DVI output card
nd
2 row: Single DVI input card / Multi-viewer card
rd
3 row: 1 Fiber DVI input card / Single DVI output card
th
4 row: 1 Fiber DVI input card / NO output card
Reply: SLOT=01_02_19!
SLOT=02_02_21!
SLOT=03_18_03!
SLOT=04_18_00!
Table 7.15 Slot status request command example
7.2.12 Control lock command
▪ It locks and unlocks the controls such as Web, RS-232, TCP/IP and UDP.
▪ It request open status of controls.
ASCII
Description
WL
Web control lock
WUL
Web control unlock
DL
Data control (UDP, TCP/IP, RS-232) lock
DUL
Data control (UDP, TCP/IP, RS-232) unlock
KL
Key control lock
KUL
Key control unlock
Table 7.16 Locking type and its ASCII data
Command
LOCK=DL!
Description and reply
Locks data control.
47
Reply: LOCK=DL!
LOCK=?!
Request current status of control method.
Reply: LOCK=WUL,DUL,KUL!
Table 7.17 Control lock command examples
7.2.13 Preset Control Commend
▪ It saves routings under a preset number
▪ It requests current Preset mode setting.
▪ It changes the name and reads the Preset status.
▪
Command
PRE=SAVE<Preset Number>!
PRE=LOAD<Preset Number>!
PRE=?!
PRENAME=<Preset Number>!
PRENAME=<Preset
Number>_<Preset Name>!
Description and reply
Requests to save the current routings under the preset number selected.
Reply: PRE=SAVE<Preset Number>_<link state>!
Example:
Send: PRE=SAVE01!
Reply: PRE=SAVE01_00^01,00^02,00^03,00^04......00^32!
(04^04 indicates input 4 linked to output 4. Input 00 indicates no link set
for the output)
Requests to load the saved preset number.
Reply: PRE=LOAD<Preset Number>_<link state>!
Example:
Send: PRE=LOAD01!
Reply: PRE=LOAD01_00^01,00^02,00^03,00^04......00^32!
Request Preset Information
Example :
Send : PRE=?!
Reply :
PRE=TAB01_01^01,02^02,~31^31,32^32!
PRE=TAB02_01^01,02^02,~31^31,32^32!
PRE=TAB03_01^01,02^02,~31^31,32^32!
~~
PRE=TAB10_01^01,02^02,~31^31,32^32!
Request Preset Name
Example :
Send : PRENAME=02!
Reply : PRENAME=[02]PRENUMBER02!
Setting Preset Name
Example :
Send : PRENAME=02_MeetRomm!
Reply : PRENAME=[02]MeetRomm!
Table 7.18 Preset control command examples
48
7.2.14 Power State Request
▪ It requests current status of SMPS Power On / Off.
Command
PWR=?!
Description and reply
Request SMPS OnOff State
Reply: PWR=L_ON,R_OFF!
Left SMPS On, Right SMPS Off
Table 7.19 Power State Request command examples
7.2.15 Firmware Version Request
Command
VER=?!
Description and reply
Request Firmware Version
Reply: VER=M_100,I_100,O_100!
Main Version : 1.0.0
Input Version : 1.0.0
Output Version : 1.0.0
Table 7.20 Firmware Version Request command examples
49
Chapter 8. Firmware update
OMM-2500 has three-way Firmware settings, 1) Main Firmware, 2) Input Firmware, 3) Output
Firmware. All Firmware ports are placed on the VGEXT of the rear panel.
▪ RS-232 / F1 port for Main Firmware: Use a supplied download cable, RS-232
▪ F2 port for Input Firmware: Use a supplied download cable, RJ11 to RS-232
▪ F3 port for Output Firmware: Use a supplied download cable, RJ11 to RS-232
1. Please install
[Note]
under Windows XP OS.
Megaboot.exe can’t be installed under Windows 7 and Vista OS.
2. Click ①, Open of ‘File to be programmed in the Flash’ to select directory and file (hex.
Format)
to be uploaded.
50
①
②
③
3. Connect the Firmware Port to be updated in a rear panel of OMM-2500 to RS-232 (Comm
port) in PC using a supplied download cable.
4. Select ②, ‘CommPort’ to select communication port of PC for RS-232 communication with
OMM-2500.
5. To enable CommPort, Click ③ when it shown as ‘Serial Port Enable’.
6. Power-On of OMM-2500.
7. Then the firmware will be uploaded and its status will be shown in the message box shown as
below.
51
8. After 3~4 minutes, Application Code Runing!!! message will be shown. Then the firmware
upload is completed.
52
9. To be uploaded other Firmware files, repeat steps 2 to 8, if it’s necessary.
10. Please close a megabox.exe program and reboot OMM-2500 to run it under new
firmware.
Chapter 9. Trouble shooting
53
Problem
Symptom
Solution
No Power
Power LED Off
Check the connection of power cord to the OMM-2500
and AC power outlet and that make sure that power
switch is in the ON.
Check the Input Output cables are firmly connected to
each port of OMM-2500.
Check the Input and Output connection configuration you
want.
The display is not capable of handling graphic
resolution.
Check the compatibility of EDID in the EEPROM and
attached displays.
No Output
No Output present
When a single Input is routed to multiple outputs,
lower resolution EDID should be selected.
EX> Input 1  Output 1 (UXGA) & Output 2(SXGA)
If EEPROM 1 store the display 1 EDID (UXGA), the
display 2 (SXGA) will not work due to resolution limit.
The source has stopped sending a graphic signal.
Check the Input source status by connecting it to available
monitor without the OMM-2500.
Chapter 10. Specification
54
10.1 General Specification
Section
Video
resolution
HDCP
Basic Spec.
Main VESA resolution & Main vertical
frequency from 640x480 up to WUXGA
(1920x1200), @60Hz
WQXGA (2560x1600),@60Hz (Dual link ,
DisplayPort card only)
Section
Reference video
output
Diagnosis
Configuration
Save & Restore for Current connection & Control
condition by internal memory
Video format conversion without scaling
function
Multi -viewer
With additional output card (QDVI-O),
Quad view & picture in picture (PIP)
EDID management
In/Output
32 x 32 (4 ports in one in/output card)
16 x 16 (2 ports in one in/output card)
Color
Switching
speed
< 1 sec (If No format searching by Display)
Weight
Cooling system
Certifications
Control system
Touch LCD
1)
2)
3)
4)
Default Mode
Auto Detect Mode
Output Copy Mode
Resolution List Mode
Black
Pressure type
In/Output card Spec.
Section
Model name
In/Output port
Single DVI input
SDVI-4EI
4 x DVI-D receptacle
Single DVI output
SDVI-4EO
4 x DVI-D receptacle
Dual DVI input
DDVI-2EI
2 x DVI-D receptacle
Dual DVI output
DDVI-2EO
2 x DVI-D receptacle
4 x HDMI receptacle
4 x HDMI receptacle
4 x SDI receptacle
4 x SDI receptacle
4 x DP receptacle
4 x DP receptacle
440 x 440 x 311mm (WDH), (7U, 19”)
< 15Kg (net weight with dual powers)
Cooling fan (Forced cooling system)
CE / FCC
Front-key, Touch LCD, RS-232, TCP/IP,
Web
Temperature (℃)
Operating
condition
9 output video resolutions with 16 patterns
1) In/Output Link condition
2) source & display Link condition
3) EDID, HDCP information by the remote control
through the Web
Support : Electric DVI, Dual link DVI, HDMI
Non-support : Optical DVI, SDI, DisplayPort
Video format
conversion
Size
Basic Spec.
HDMI input
HDMI-4EI
HDMI output
HDMI-4EO
SDI input
SDI-4EI
SDI output
SDI -4EO
DisplayPort input
DP1-4EI
DisplayPort output
DP1-4EO
Quad output
QDVI-O
1 fiber DVI input
1fiber DVI output
SDVI-1FI
SDVI-1FO
1x DVI-D receptacle
+ 1x SC receptacle
4 x SC receptacle
4 x SC receptacle
Temperature (℃)
-30 ~ +70
Relative humidity (%)
+10~ +95
Atmospheric
Pressure (hPa)
500 ~1060
10 ~ 40
Relative humidity (%)
+30~ +75
Atmospheric
Pressure (hPa)
700 ~ 1060
Transport
And
Storage condition
10.2 Power Specification
55
AC Power
1) Input Voltage : AC100~240V ±10%, 50/60Hz
2) Power consumption : 4.5~1.8A
3) Shall have a power cord that complies with regulatory requirements imposed by the country of
sale.
4) Incorporate a power cord management system for securing a bundled up cord.
External Fuse
1) Input Voltage: AC100~240V ±10%, 50/60Hz
2) Power consumption: 4.5~1.8A
3) F 16 AH250V
10.3 SDI video input and output scaling condition
Input card
Output card
Input resolution
480i
Output resolution
576i
SDI card
SDI card
720p@ 23.98
720p@ 30
720p@ 24
720p@ 50
720p@ 25
720p@ 59.94
720p@ 29.97
720p@ 60
1035i
720p@ 60
1080i, 1080sf
1080p@ 23.98
1080p@ 24
1080p @ 50
1080p@ 25
1080p @ 59.94
SXGA (1280x1024)
576i
HDMI, DVI,
Fiber card
SDI card
1080p@ 60
1080p @ 60
480i
HDMI, DVI,
Fiber card
1080p@ 60
1080p @ 30
1080p@ 29.97
SDI card
720p@ 60
720p@ 23.98
720p@ 30
720p@ 24
720p@ 50
720p@ 25
720p@ 59.94
720p@ 29.97
720p@ 60
720p@ 60
1035i
720p@ 60
1080i, 1080sf
1080p@ 60
1080p@ 23.98
1080p @ 30
1080p@ 24
1080p @ 50
1080p@ 25
1080p @ 59.94
1080p@ 29.97
1080p @ 60
depends on
V display
1080p@ 60
720≤ V display <1080
720p@ 60
V display ≥1080
1080p@ 60
[Note] Both SDI input and output card do not support audio signal.
10.4 Compatibility between Dual link DVI In/Output cards and another
56
In/Output cards
Output
DDVI-2EO
SDVI-4EO
SDVI-1FO
HDMI-4EO
SDI -4EO
Dual
DVI
Pass
N/D
N/D
N/D
N/D
Single
DVI
Pass
Pass
Pass
Pass
Pass
SDVI-4EI
Pass
Pass
Pass
Pass
Pass
SDVI-1FI
Pass
Pass
Pass
Pass
Pass
HDMI-4EI
N/D
Pass
Pass
Pass
Pass
SDI -4EI
N/D
Pass
Pass
Pass
Pass
Input
DDVI-2EI
10.5 Compatibility between DisplayPort In/Output cards and another
In/Output cards
Input card
Output card
Resolution
DP1-4EI
DP1-4EO
Up to WQXGA (2560x1600) at 60Hz
(Not support Deep color)
SDVI-1FO
SDVI-4EO
DP1-4EO
HDMI-4EO
Up to WQXGA (2560x1600) at 60Hz
SDI-4EO
DDVI-2EO
57
Chapter 11. Warranty Information
1 (One) Year Warranty
Opticis warrants this optical DVI extension module to be free from defects in workmanship and
materials, under normal use and service, for a period of one (1) year from the date of purchase from
Opticis or its authorized resellers.
If a product does not work as warranted during the applicable warranty period, Opticis shall, at its
option and expense, repair the defective product or part, deliver to customer an equivalent product or
part to replace the defective item, or refund to customer the purchase price paid for the defective
product.
This product should be serviced such as repair or replace by Opticis and please contact your reseller
or Opticis if you have any problems. All products that are replaced will become the property of Opticis.
Replacement products may be new or reconditioned.
Any replaced or repaired product or part has a ninety (90) day warranty or the reminder of the initial
warranty period, whichever is longer.
Opticis shall not be responsible for any software, firmware, information, or memory data of customer
contained in, stored on, or integrated with any products returned to Opticis for repair under warranty or
not.
Warranty Limitation and Exclusion
Opticis shall have no further obligation under the foregoing limited warranty if the product has been
damaged due to abuse, misuse, neglect, accident, unusual physical or electrical stress, unauthorized
modifications, tampering, alterations, or service other than by Opticis or its authorized agents, causes
other than from ordinary use or failure to properly use the product in the application for which said
product is intended.
Dispose of Old Electrical & Electronic Equipment
(Applicable in the European Union and other European countries with separate systems)
This marking shown the product or its literature, indicates that it should not be
disposed with other household wastes at the end of its working life. To prevent
58
possible harm to the environment or human health from uncontrolled waste disposal,
please separate this from other types of wastes and recycle it responsibly to promote
the sustainable reuse of material resources.
Household users should contact either the retailer where they purchased this product, or their local
government office, for details of where and how they can take this item for environmentally safe
recycling.
Business users should contact their supplier and check the terms and conditions of the purchase
contract. This product should not be mixed with other commercial wastes for disposal
Chapter 12. Safety Instructions
WARNING: Do not touch signal input, signal output of other connectors, and the patient
simultaneously.
WARNING: Do not connect any accessory except provided by Opticis. Any damage caused other
power adapters or accessories will not be taken any responsibility by Opticis.
59
Chapter 13. Maintenance
No special maintenance is required for the matrix and power. Ensure that the matrix and power are
stored or used in a benign environment free from liquid or dirt contamination.
Refer all service and repair issues to Opticis.
▪
For commercial or general product support, contact your reseller. For technical service,
contact Opticis by email techsupp@opticis.com or visit its website at www.opticis.com
Cleaning
▪
Turn off the power.
▪
Remove all of the electrical and optical fiber from the Modular matrix chassis, OMM-2500.
▪
Separate each input / output card from the body.
▪
Put the cards on the safety place and keep it carefully.
▪
Clean with dry cloth inside of the body after each card is separated.
▪
Remove dust on the surface of each card with air gun.
▪
Install each card back to the body
60
Opticis Locations
HQ
7F, 166, Jeongjail-ro
Bundang-gu , Sungnam-si
Gyunggi-do 13558
Rep. of KOREA
Tel: +82 (31) 719-8033
Fax: +82 (31) 719-8032
Factory
#501 Byoksan Technopia, 560,
Dunchon-daero,
Jungwon-gu,
Seongnam-si,Gyeonggi-do, 462-716
Rep. of KOREA
Tel: +82 (31) 737-8033
Fax: +82 (31) 737-8039
For order support, please contact your Distributor or Reseller.
Direktronik AB
Konsul Johnsons väg 15
SE-149 45 Nynäshamn
Sweden
+46 8 524 00 700
info@direktronik.se
www.direktronik.se
For technical support, visit Opticis web site, www.opticis.com or contact techsupp@opticis.com
Or support@direktronik.se
61
Download PDF
Similar pages