Philips Weather Clock Radio AJ260/05 Quick Start

AJ260
Clock Radio
B/3
B
R
C
QUICK START
DC 7.5V
R
A
3
ENGLISH
Radio
1. Press and hold TIME SET / RCC SYNC or
ALM1 / ALM2 until the time digits flash.
2. Press and hold TUNING +/- to adjust time.
3. Press TIME SET / RCC SYNC or ALM1 /
ALM2 to confirm.
4. Repeat the steps 2~3 to complete all the other
time items setting.
1. Press RADIO ON/OFF once to switch on the
radio.
2. Press AUTO SCAN/DATE to program all
available stations.
3. Press PRESET+/- until the desired preset station
is displayed.
To perform RCC (Radio Controlled Clock)
searching
Press briefly TIME SET / RCC SYNC.
is
displayed.
Weather forecast and Indoor
thermometer
– The RCC time search will stop 10 minutes later if no
time signal is received.
– Refer to the supplied user manual for RCC
information.
Step C
Selecting the Alarm mode
Helpful hints:
– If you have selected RADIO, make sure you have
properly tuned to a station before turning off the set.
1
3 ways to switch off the alarm
Step B
How to set the Clock & Alarm time
In standby mode, slide the RADIO/BUZ to select
desired mode.
AJ260_05-QSG
– Refer to the supplied user manual for more
information about the outdoor sensor.
• Either press briefly: SLEEP/ALARM RESET or
REPEAT ALARM/BRIGHTNESS
CONTROL.
• Press ALM1 or ALM2.
Notes:
Thanks for buying Philips AJ260 clock radio.
Our Quick Start guides you through just some of the features on the set.
Please read our instruction booklet to really rise & shine!
Note:
• Connect the supplied mains adapter to the set’s
7.5V DC jack and the plug into a wall outlet.
Step A
1. Place the sensor in a desired open area. The place
must be within 50 meters away from the main unit.
(Make sure that the sensor is loaded with 2 AA
batteries.)
• For the first time using the outdoor sensor and
the main unit, press RESET located on the sensor
back, and RESET located in the battery
compartment of the main unit. Then, the main unit
will begin to receive transmission from the sensor.
• To update the outdoor temperature from the
sensor any time, press and hold
AUTO SCAN/DATE for 5 seconds.
The unit can auto detect and measure atmospheric
pressure changes to graphically display the weather
forecast in the next 12 to 24 hours, and current
indoor temperature.
Note:
– The weather forecast based on the atmospheric
pressure may vary slightly from the actual weather
situation.
Using the outdoor sensor
The outdoor sensor is supplied to work with the
main unit to measure and display the outdoor
temperature.
8/3/07, 12:00
Printed in China
PDCC-JH-0710
AJ260
Clock Radio
B/3
B
R
C
QUICK START
DC 7.5V
R
A
3
ENGLISH
Radio
1. Press and hold TIME SET / RCC SYNC or
ALM1 / ALM2 until the time digits flash.
2. Press and hold TUNING +/- to adjust time.
3. Press TIME SET / RCC SYNC or ALM1 /
ALM2 to confirm.
4. Repeat the steps 2~3 to complete all the other
time items setting.
1. Press RADIO ON/OFF once to switch on the
radio.
2. Press AUTO SCAN/DATE to program all
available stations.
3. Press PRESET+/- until the desired preset station
is displayed.
To perform RCC (Radio Controlled Clock)
searching
Press briefly TIME SET / RCC SYNC.
is
displayed.
Weather forecast and Indoor
thermometer
– The RCC time search will stop 10 minutes later if no
time signal is received.
– Refer to the supplied user manual for RCC
information.
Step C
Selecting the Alarm mode
Helpful hints:
– If you have selected RADIO, make sure you have
properly tuned to a station before turning off the set.
1
3 ways to switch off the alarm
Step B
How to set the Clock & Alarm time
In standby mode, slide the RADIO/BUZ to select
desired mode.
AJ260_05-QSG
– Refer to the supplied user manual for more
information about the outdoor sensor.
• Either press briefly: SLEEP/ALARM RESET or
REPEAT ALARM/BRIGHTNESS
CONTROL.
• Press ALM1 or ALM2.
Notes:
Thanks for buying Philips AJ260 clock radio.
Our Quick Start guides you through just some of the features on the set.
Please read our instruction booklet to really rise & shine!
Note:
• Connect the supplied mains adapter to the set’s
7.5V DC jack and the plug into a wall outlet.
Step A
1. Place the sensor in a desired open area. The place
must be within 50 meters away from the main unit.
(Make sure that the sensor is loaded with 2 AA
batteries.)
• For the first time using the outdoor sensor and
the main unit, press RESET located on the sensor
back, and RESET located in the battery
compartment of the main unit. Then, the main unit
will begin to receive transmission from the sensor.
• To update the outdoor temperature from the
sensor any time, press and hold
AUTO SCAN/DATE for 5 seconds.
The unit can auto detect and measure atmospheric
pressure changes to graphically display the weather
forecast in the next 12 to 24 hours, and current
indoor temperature.
Note:
– The weather forecast based on the atmospheric
pressure may vary slightly from the actual weather
situation.
Using the outdoor sensor
The outdoor sensor is supplied to work with the
main unit to measure and display the outdoor
temperature.
8/3/07, 12:00
Printed in China
PDCC-JH-0710
AJ260
Clock Radio
B/3
B
R
C
QUICK START
DC 7.5V
R
A
3
ENGLISH
Radio
1. Press and hold TIME SET / RCC SYNC or
ALM1 / ALM2 until the time digits flash.
2. Press and hold TUNING +/- to adjust time.
3. Press TIME SET / RCC SYNC or ALM1 /
ALM2 to confirm.
4. Repeat the steps 2~3 to complete all the other
time items setting.
1. Press RADIO ON/OFF once to switch on the
radio.
2. Press AUTO SCAN/DATE to program all
available stations.
3. Press PRESET+/- until the desired preset station
is displayed.
To perform RCC (Radio Controlled Clock)
searching
Press briefly TIME SET / RCC SYNC.
is
displayed.
Weather forecast and Indoor
thermometer
– The RCC time search will stop 10 minutes later if no
time signal is received.
– Refer to the supplied user manual for RCC
information.
Step C
Selecting the Alarm mode
Helpful hints:
– If you have selected RADIO, make sure you have
properly tuned to a station before turning off the set.
1
3 ways to switch off the alarm
Step B
How to set the Clock & Alarm time
In standby mode, slide the RADIO/BUZ to select
desired mode.
AJ260_05-QSG
– Refer to the supplied user manual for more
information about the outdoor sensor.
• Either press briefly: SLEEP/ALARM RESET or
REPEAT ALARM/BRIGHTNESS
CONTROL.
• Press ALM1 or ALM2.
Notes:
Thanks for buying Philips AJ260 clock radio.
Our Quick Start guides you through just some of the features on the set.
Please read our instruction booklet to really rise & shine!
Note:
• Connect the supplied mains adapter to the set’s
7.5V DC jack and the plug into a wall outlet.
Step A
1. Place the sensor in a desired open area. The place
must be within 50 meters away from the main unit.
(Make sure that the sensor is loaded with 2 AA
batteries.)
• For the first time using the outdoor sensor and
the main unit, press RESET located on the sensor
back, and RESET located in the battery
compartment of the main unit. Then, the main unit
will begin to receive transmission from the sensor.
• To update the outdoor temperature from the
sensor any time, press and hold
AUTO SCAN/DATE for 5 seconds.
The unit can auto detect and measure atmospheric
pressure changes to graphically display the weather
forecast in the next 12 to 24 hours, and current
indoor temperature.
Note:
– The weather forecast based on the atmospheric
pressure may vary slightly from the actual weather
situation.
Using the outdoor sensor
The outdoor sensor is supplied to work with the
main unit to measure and display the outdoor
temperature.
8/3/07, 12:00
Printed in China
PDCC-JH-0710