Philips docking entertainment system DC190/05 User manual

Register your product and get support at
Docking Entertainment System
www.philips.com/welcome
DC190
EN User manual
1 Important
Safety
Notice
4
4
4
7 Product information
Specifications
11
11
8 Troubleshooting
12
2 Your Docking Entertainment System 5
Introduction
What’s in the box
Overview of the main unit
3 Get started
Connect power
Set clock
Turn on
Adjust volume
4 Play
Play from iPod
Play from an external device
5 Listen to radio
Tune to a radio station
Program radio stations automatically
Program radio stations manually
Select a preset radio station
6 Other features
Set the alarm timer
Set the sleep timer
Adjust display brightness
5
5
6
7
7
8
8
8
8
8
9
9
9
9
10
10
10
10
11
11
EN
3
English
Contents
1 Important
Safety
Important Safety Instructions
a Read these instructions.
b Keep these instructions.
c Heed all warnings.
d Follow all instructions.
e Do not use this apparatus near water.
f Clean only with dry cloth.
g Do not block any ventilation openings.
Install in accordance with the
manufacturer’s instructions.
h Do not install near any heat sources
such as radiators, heat registers, stoves,
or other apparatus (including amplifiers)
that produce heat.
i Protect the power cord from being
walked on or pinched, particularly at
plugs, convenience receptacles, and
the point where they exit from the
apparatus.
j Only use attachments/accessories
specified by the manufacturer.
k Use only with the cart,
stand, tripod, bracket,
or table specified by the
manufacturer or sold with
the apparatus. When a cart
is used, use caution when
moving the cart/apparatus combination
to avoid injury from tip-over.
l Unplug this apparatus during lightning
storms or when unused for long periods
of time.
m Refer all servicing to qualified service
personnel. Servicing is required when
the apparatus has been damaged in any
4
EN
way, such as power-supply cord or plug
is damaged, liquid has been spilled or
objects have fallen into the apparatus,
the apparatus has been exposed to rain
or moisture, does not operate normally,
or has been dropped.
n Apparatus shall not be exposed to
dripping or splashing.
o Do not place any sources of danger on
the apparatus (e.g. liquid filled objects,
lighted candles).
p This product may contain lead and
mercury. Disposal of these materials
may be regulated due to environmental
considerations. For disposal or recycling
information, please contact your local
authorities or the Electronic Industries
Alliance: www.eiae.org.
q Where the MAINS plug or an appliance
coupler is used as the disconnect device,
the disconnect device shall remain
readily operable.
Warning
• Never remove the casing of this apparatus.
• Never lubricate any part of this apparatus.
• Never place this apparatus on other electrical
equipment.
• Keep this apparatus away from direct sunlight,
naked flames or heat.
• Ensure that you always have easy access to the
power cord, plug or adaptor to disconnect the
apparatus from the power.
Notice
This product complies with the
radio interference requirements
of the European Community.
This product complies with the
requirements of the following directives and
guidelines: 2004/108/EC + 2006/95/EC
Any changes or modifications made to this
device that are not expressly approved by
Philips Consumer Lifestyle may void the user’s
authority to operate the equipment.
Your product is designed and
manufactured with high quality
materials and components, which
can be recycled and reused.
When you see the crossed-out
wheel bin symbol attached to a
product, it means the product
is covered by the European
Directive 2002/96/EC:
Never dispose of your product
with other household waste. Please inform
yourself about the local rules on the separate
collection of electrical and electronic products.
The correct disposal of your old product helps
prevent potentially negative consequences on
the environment and human health.
Environmental information
All unnecessary packaging has been omitted.
We have tried to make the packaging easy to
separate into three materials: cardboard (box),
polystyrene foam (buffer) and polyethylene
(bags, protective foam sheet.)
Your system consists of materials which can
be recycled and reused if disassembled by
a specialized company. Please observe the
local regulations regarding the disposal of
packaging materials, exhausted batteries and
old equipment.
2 Your Docking
Entertainment
System
English
Recycling
Congratulations on your purchase, and
welcome to Philips! To fully benefit from the
support that Philips offers, register your product
at www.philips.com/welcome.
Introduction
With this unit, you can enjoy audio from the
iPod, other audio devices, or the radio.
The radio, iPod, or buzzer can be set as the
alarm timer. You can set two alarm timers to go
off at different times.
What’s in the box
Check and identify the contents of your
package:
• Main unit
• 1 x AC adaptor
• 1 x MP3 link cable
• User manual
• Quick start guide
EN
5
Overview of the main unit
6
EN
b REPEAT ALARM/BRIGHTNESS
CONTROL
• Repeat the alarm.
• Adjust the display brightness.
c
•
e PRESET +/• Select a preset radio station.
• Adjust time.
f Display panel
• Show current status.
g Dock compartment
h
•
Start or pause iPod play.
/
•
•
q SLEEP
• Set the sleep timer.
3 Get started
Turn on the unit or switch to
standby mode.
d SOURCE
• Select a source: iPod, FM tuner or
MP3 link.
i
p VOL +/• Adjust volume.
• Adjust time.
Skip to the previous/next audio file.
Search within an audio file.
j TUNING +/• Tune to a radio station.
• Adjust time.
k TIME SET/AUTO SCAN
• Set the clock.
• Scan radio stations.
l WAKE TO iPod/RADIO/BUZZ
• Select alarm mode.
m MP3-LINK
• Jack for an external audio device.
n DC IN
• Power supply socket.
o iPod dock
• Load an iPod player.
English
a ALARM 1/ALARM 2
• Set the alarm timer.
• View the alarm time.
• Turn off the alarm tone.
Caution
• Use of controls or adjustments or
performance of procedures other than herein
may result in hazardous radiation exposure or
other unsafe operation.
Always follow the instructions in this chapter in
sequence.
If you contact Philips, you will be asked for the
model and serial number of this apparatus. The
model number and serial number are on the
bottom of the apparatus. Write the numbers
here:
Model No. __________________________
Serial No. ___________________________
Connect power
Caution
• Risk of product damage! Ensure that the power
voltage corresponds to the voltage printed on
the back or underside of the apparatus.
• Risk of electric shock! When you unplug the
AC adaptor, always pull the plug from the
socket. Never pull the cord.
• Before connecting the AC adaptor, ensure you
have completed all other connections.
Note
• The type plate is located on the bottom of the
main unit.
1
Connect one end of the AC adaptor to
the DC IN socket on the main unit.
EN
7
Switch to standby
1
Press again to switch the unit to
standby mode.
» The clock (if set) appears on the
display panel.
Adjust volume
1 During play, press VOL +/- to increase/
2
decrease the volume.
Connect the other end of the AC
adaptor to the wall outlet.
4 Play
Play from iPod
You can enjoy audio from iPod through this unit.
Compatible iPod
Set clock
1 In standby mode, press and hold TIME
SET/AUTO SCAN for 2 seconds.
» The hour digits begin to blink.
2
3
Press TUNING +/- to set the hour.
Press TIME SET/AUTO SCAN.
» The minute digits begin to blink.
4
5
Press TUNING +/- to set the minute.
6
7
Press TUNING +/- to set the week day.
Press TIME SET/AUTO SCAN to
confirm.
» The week day digits begin to blink.
Press TIME SET/AUTO SCAN to
confirm.
Turn on
1 Press .
» The unit switches to the last selected
source.
8
Apple iPod models with a 30-pin dock
connector:
• iPod classic, iPod touch, iPod nano, iPod
5th generation (video), iPod with color
display, iPod mini.
EN
Load the iPod
1
Push to open the dock compartment.
Place the iPod in the dock.
3
Start to play the device (see the device
user manual).
English
2
5 Listen to radio
Note
• Only FM radio reception is available on this
unit.
Tune to a radio station
Remove the iPod
1
Tip
Pull the iPod out of the dock.
• Position the antenna as far as possible from
Listen to the iPod
1
2
TV, VCR or other radiation source.
• For optimal reception, fully extend and adjust
the position of the antenna.
Ensure that the iPod is loaded correctly.
Press SOURCE repeatedly to select iPod
source.
» The connected iPod plays automatically.
•
•
•
To pause/resume play, press
.
To skip to a track, press / .
To search during play, press and
hold / , then release to resume
normal play.
1
Press SOURCE repeatedly to select FM
tuner.
2
Press and hold TUNING +/- for more
than 2 seconds.
» The radio tunes to a station with
strong reception automatically.
3
Repeat step 2 to tune to more stations.
• To tune to a weak station, press
TUNING +/- repeatedly until you
find optimal reception.
Charge the iPod
When the unit is connected to power, the
docked iPod begins to charge.
Play from an external device
You can also listen to an external audio device
through this unit.
1
Press SOURCE repeatedly to select MP3
link source.
2
Connect the supplied MP3 link cable to:
• the MP3-LINK jack (3.5mm) on the
back of the unit.
• the headphone jack on an external
device.
Program radio stations
automatically
You can program a maximum of 20 preset
radio stations.
1
In the tuner mode, press and hold TIME
SET/AUTO SCAN for more than 2
seconds to activate automatic program
mode.
» All available stations are programmed
in the order of waveband reception
strength.
» The first programmed radio station is
broadcast automatically.
EN
9
Program radio stations
manually
You can program a maximum of 20 preset
radio stations.
1
2
Tune to a radio station.
Press TIME SET/AUTO SCAN to activate
the program mode.
» The preset number begins to blink.
3
4
Press PRESET +/- to select a number.
5
Repeat the above steps to program other
stations.
5
6
Repeat steps 3-4 to set the minute.
7
Repeat steps 3-4 to set the maximum
alarm volume.
Repeat steps 3-4 to select whether to
ring alarm on weekdays or at weekend.
» “L XX(volume level)” begins to blink.
Set alarm mode
1
Press TIME SET/AUTO SCAN to
confirm.
Adjust the WAKE TO iPod/RADIO/
BUZZ control to select the source for
the alarm.
» When the alarm time comes, the
selected iPod, radio or buzzer turns on.
Tip
Note
• If iPod source is selected but no iPod is loaded,
the buzzer is selected automatically.
• To overwrite a programmed station, store
another station in its place.
Select a preset radio station
1 Press PRESET +/- to select a preset
Activate and deactivate the alarm
timer
1
number.
6 Other features
•
To deactivate the alarm timer, press
ALARM 1 or ALARM 2 repeatedly
until is displayed.
» If the timer is deactivated,
or
disappears.
Set the alarm timer
You can set two alarms which go off at different
time.
1
Ensure that you have set the clock
correctly.
2
Press and hold ALARM 1 or ALARM 2
for 2 seconds.
»
or
and hour digits begin to
blink.
3
Press TUNING +/- repeatedly to set the
hour.
4
Press ALARM 1 or ALARM 2 to confirm.
»
or
and minute digits begin
to blink.
10
EN
Press ALARM 1 or ALARM 2 repeatedly
to activate the timer.
» If the timer is activated,
or
is
displayed.
Repeat alarm
1
When the alarm rings, press REPEAT
ALARM/BRIGHTNESS CONTROL.
» The alarm repeats ringing minutes later.
Tip
• You can press TUNING+/- to adjust interval
to repeat alarm.
1
When the alarm rings, press the
corresponding ALARM 1 or ALARM 2.
» The alarm stops but the alarm settings
remain.
View the alarm settings
1
This unit can switch to standby automatically
after a set period of time.
Press SLEEP repeatedly to select a set
period of time (in minutes).
» When the sleep timer is activated, the
display shows .
To deactivate sleep timer
1
Note
• Product information is subject to change
without prior notice.
Press ALARM 1 or ALARM 2.
Set the sleep timer
1
7 Product
information
English
Stop alarm ring
Press SLEEP repeatedly until [OFF] (off)
is displayed.
» When the sleep timer is deactivated,
disappears on the display.
Note
• When the sleep timer is activated, the volume
will gradually decrease.
Adjust display brightness
1 Press BRIGHTNESS CONTROL
repeatedly to select different levels of
display brightness.
Specifications
Amplifier
Rated Output Power 2X1.5 W RMS
Signal to Noise Ratio >55 dB
MP3 Link
0.6 V RMS 10 kohm
Tuner
FM
Tuning Range
Tuning grid
Sensitivity
- Mono, 26dB S/N Ratio
- Stereo, 46dB S/N Ratio
Search Selectivity
Total Harmonic Distortion
Signal to Noise Ratio
87.5 - 108 MHz
50 KHz
<22 dBu
<45 dBu
<28 dBu
<3%
>45 dB
General information
AC power (power Input: 100-240V~,
adaptor)
50/60Hz, 0.4A; Output:
6.5V 1.3A; Brand
name: Philips; Model
No.: AS090-065-AB130
Operation Power <5W
Consumption
Standby Power
<2W
Consumption
Dimensions
- Main Unit
144 x 144 x 62 mm
(W x H x D)
Weight
- Main Unit
0.44 kg
EN
11
8 Troubleshooting
Warning
• Never remove the casing of this apparatus.
To keep the warranty valid, never try to repair
the system yourself.
If you encounter problems when using this
apparatus, check the following points before
requesting service. If the problem remains
unsolved, go to the Philips web site (www.
philips.com/welcome). When you contact
Philips, ensure that the apparatus is nearby
and the model number and serial number are
available.
No power
•
Ensure that the AC power plug of the
unit is connected properly.
•
Ensure that there is power at the AC
outlet.
No sound
•
Adjust the volume.
No response from the unit
•
Disconnect and reconnect the AC power
plug, then turn on the unit again.
Poor radio reception
•
Increase the distance between the unit
and your TV or VCR.
•
Fully extend the FM antenna.
Timer does not work
•
Set the clock correctly.
•
Switch on the timer.
12
EN
Clock/timer setting erased
•
Power has been interrupted or the power
plug has been disconnected.
•
Reset the clock/timer.
© 2009 Koninklijke Philips Electronics N.V.
All rights reserved.
DC190_05_UM_V1.1