Acer Network Card DAC960PJ User manual

DAC960PG™ and DAC960PJ™
Quick Installation Guide
PCI to Ultra SCSI
RAID Controllers
Part Number 775034-02
08P4084
© Copyright 2000 Mylex Corporation.
All Rights Reserved.
All contents of this manual are copyrighted by Mylex
Corporation. The information contained herein is the
exclusive property of Mylex Corporation and shall not be
copied, transferred, photocopied, translated on paper, film,
electronic media, or computer-readable form; or otherwise
reproduced in any way, without the express written
permission of Mylex Corporation.
Greetings
Thank you for purchasing the Mylex DAC960PG™ or DAC960PJ™ controller. This
manual describes the installation of the Mylex DAC960PG/PJ controllers. Requests for
technical information about this and other Mylex Corporation products should be made to
your Mylex authorized reseller or Mylex sales representative.
Please Notice
IBM, Mylex, RAID EzAssist, DAC960PG, and DAC960PJ are trademarks or registered
trademarks of International Business Machines corp. and its subsidiaries. Microsoft,
MS-DOS, and Windows are registered trademarks of Microsoft Corporation. Novell is a
registered trademark of Novell Corporation. LSI and Symbios Logic are registered
trademarks of LSI Logic Corporation. Other names that are trademarks may be used
herein for the purpose of identifying the products or services of their respective owners.
Unless otherwise noted, companies, names, and data used in examples herein are
fictitious.
Our Policy
Although reasonable efforts have been made to assure the accuracy of the information
contained herein, this publication could include technical inaccuracies or typographical
errors. Mylex Corporation expressly disclaims liability for any error in this information,
and for damages, whether direct, indirect, special, exemplary, consequential or otherwise,
that may result from such error, including but not limited to loss of profits resulting from
the use or misuse of the manual or information contained therein (even if Mylex
Corporation has been advised of the possibility of such damages). Any questions or
comments regarding this document or its contents should be addressed to Mylex
Corporation at the address shown on the cover.
The following paragraph does not apply to the United Kingdom or any country where such
provisions are inconsistent with local law:
MYLEX CORPORATION PROVIDES THIS PUBLICATION “AS IS” WITHOUT
WARRANTY OF ANY KIND, EITHER EXPRESS OR IMPLIED, INCLUDING, BUT
NOT LIMITED TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY OR
FITNESS FOR A PARTICULAR PURPOSE.
Some states do not allow disclaimer of express or implied warranties or the limitation or
exclusion of liability for indirect, special, exemplary, incidental or consequential damages
in certain transactions; therefore, this statement may not apply to you. Also, you may have
other rights which vary from jurisdiction to jurisdiction.
Information in this publication is subject to change without notice and does not represent a
commitment on the part of Mylex Corporation. Changes may be made periodically to the
information herein; these changes will be incorporated in new editions of the publication.
Mylex Corporation reserves the right to make improvements and/or changes at any time in
the product(s) and/or program(s) described in this publication.
It is possible that this publication may contain reference to, or information about, Mylex
Corporation products (machines and programs), programming or services that are not
announced in your country. Such references or information must not be construed to mean
that Mylex Corporation intends to announce, provide, or make available such Mylex
products, programming, or services in your jurisdiction.
Regulatory Information
The DAC960PG and DAC960PJ comply with the following regulatory
agencies:
Federal Communications Commission
The FCC information statements are in Appendix E of the DAC960PG and
DAC960PJ Installation Guide.
Community of Europe
The CE information statements are in Appendix E of the DAC960PG and
DAC960PJ Installation Guide.
Underwriters Laboratories
 WARNING
This controller is furnished with a nonvolatile
RAM (NVRAM) chip that uses a sealed lithium
battery/crystal module. Replace the module only
with the same or equivalent type recommended by
the manufacturer. Dispose of the used battery/
crystal module according to the manufacturer's
instructions. Never incinerate a battery as it could
explode and cause serious injury.
Table of Contents
Hardware Installation
Introduction ........................................................................................... 1
Performing an Installation ..................................................................... 1
Connectors, Jumpers ..................................................................... 2
Installing the DAC960 into the System ................................................. 3
What to Do Next .................................................................................... 5
Manual No. 775034
iv
Hardware Installation
Introduction
The DAC960PG and DAC960PJ are versatile PCI to Ultra SCSI RAID
controllers. This quick installation guide assumes that the user is familiar
with controller, disk drive, and RAID terminology.
Performing an Installation
 WARNING
To avoid electrical shock, do not attempt to
perform this hardware installation with power on.
Disconnect the system from the electrical wall
outlet.
Manual No. 775034
1
Connectors and Jumpers
Up to three Ultra SCSI channels are supported on the controller. The SCSI
connector locations are shown in Figure 1.
All the jumpers should normally be set to their default settings. See Table 1
for default jumper settings. Jumper locations are shown in Figure 1.
Figure 1. DAC960PG/PJ with Component Locations
Table 1. Jumper and Connector Descriptions
Jumper
Default Setting
JP4
Header for optional front panel LED
JP5
Serial Port Connector
JP6
maintenance – do not use
J5
2
Description
–
–
Intelligent Battery Backup connector – If an IBBU is
not installed, a loopback plug must be installed in this
socket.
Installed
Installed at
factory
DAC960PG DAC960PJ Quick Installation Guide
Contents
Installing the DAC960PG or DAC960PJ into the
System
1. With the power off, plug the DAC960PG or DAC960PJ controller into
an available PCI slot (see Figure 2).
System Board
Plug Controller into
any Available PCI
Slot
Figure 2. Plugging the DAC960PG or DAC960PJ into a PCI Slot
2. Set the SCSI ID on each internal drive to a unique address between
0 and 15, but do not use address 7, as it is reserved for the controller.
See the documentation that comes with your drives for instructions on
how to do this.
 Caution
If internal and external drives are used, be sure that no
drive addresses are duplicated. External SCSI
cabinets usually automatically assign drive addresses
according to where in the cabinet the drives are
located.
3. Disable termination on all drives connected to the controller. See the
documentation that comes with your drives for instructions on how to
do this.
4. Enable termination power on all drives connected to the controller. See
the documentation that comes with your drives for instructions on how
to do this.
Manual No. 775034
3
5. Set the SCSI ID for each external disk drive to a unique address
between 0 and 15, but do not use address 7 (reserved for the controller).
Do not duplicate SCSI IDs used by internal drives designated for the
same channel. For information on how to set SCSI IDs, refer to the disk
drive documentation.
If you are using an external SCSI cabinet, please see the Caution note
above.
6. Connect a wide, high-density, 68-pin SCSI ribbon cable to the internal
SCSI connectors on the DAC960PG or DAC960PJ controller, and
connect the other cable connectors to any internal SCSI drives as
required (see Figure 3).
7. Connect an active terminator to the end of the SCSI ribbon cable at the
end farthest from the controller (see Figure 3).
T
T
DAC960PG/PJ Controller
Figure 3. Connecting Internal and External Drives
8. Connect a wide, round, 68-pin Very High Density Connector Interface
(VHDCI) cable to the external SCSI connector on the DAC960PG or
DAC960PJ controller, and connect the other end of the cable to an
external drive cabinet as required (see Figure 3). External drive
cabinets usually have termination built into the end of the SCSI bus.
Check the documentation that comes with your drive cabinet to be sure
this is the case. If not, use an active terminator at the end of the bus.
4
DAC960PG DAC960PJ Quick Installation Guide
Contents
☛ Note
The DAC960PG or DAC960PJ controller
automatically determines whether or not its own onboard termination is required and automatically
enables or disables on-board termination as necessary.
Figure 4 shows a completed, typical installation of the DAC960PG or
DAC960PJ controller.
T
T
System Board
Figure 4. DAC960PG or DAC960PJ in a Typical Installation
The hardware portion of the installation is complete.
What to Do Next
1. Use RAID EzAssist to create an automatic or a custom RAID
Configuration.
Refer to the RAID EzAssist Configuration Utility Quick Configuration
Guide, or RAID EzAssist Configuration Utility User Reference Guide.
2. Install the DAC960PG or DAC960PJ controller drivers appropriate for
your server’s network operating system.
Refer to the PCI Disk Array Controller Drivers Installation Guide and
User Manual.
Manual No. 775034
5
6
DAC960PG DAC960PJ Quick Installation Guide
WARRANTY REGISTRATION CARD
10. Have you ever purchased Mylex products in the past?
❏ Yes
❏ No
P/N: 772062-00
3-99
Printed in U.S.A.
❏ Monitor______________________________________
❏ Operating System __________________________________________________
7. What add-ons or peripherals are you most considering for future purchase? ______________________________________________________________________
8. What best describes your occupation?
❏ Management/Administration
❏ Sales/Service
❏ Technical-Scientific/Engineering
❏ MIS
❏ Other____________________
9. Do you have any comments or suggestions? _______________________________________________________________________________________________
❏ Data Retrieval
❏ Multi-User
❏ Multi-Tasking
❏ Database
5. Which factor most influenced your purchase?
❏ Company Reputation
❏ Price
❏ Features (List)_____________________________________ ❏ Performance
6. What does your computer system include? (Please specify brand and model)
❏ System Unit___________________________________
❏ Peripherals _______________________________________________________
If yes, which products? _____________________
2. Where will this product be used?
11. Who purchased this product?
❏ Home
❏ Workplace
❏ Individual
❏ Company
3. What other brands, if any, did you consider? _______________________________________________________________________________________________
4. Please indicate the most common uses of your system:
❏ Personal
❏ Business
❏ Graphics (CAD/CAM or Business Graphics)
❏ Accounting
❏ Digital Video
❏ Article Review ❏ Friend
❏ Retailer__________________________________________ ❏ Salesperson
❏ Other
1. How did you first learn about MYLEX products?
❏ Advertisement (Name of Pub)________________________
In order for Mylex to better serve your needs, please complete the following:
STATE: ___________________________________________________ ZIP CODE: __________________________ COUNTRY:__________________________
ADDRESS:________________________________________________________________ CITY: _____________________________________________________
PURCHASED FROM: __________________________________________________________________________________________________________________
DATE PURCHASED: ______________________________ MODEL NO: ______________________________ SERIAL NO: _____________________________
TELEPHONE: _____________________________________ FAX NO: ________________________________ E-MAIL: ________________________________
STATE: ___________________________________________________ ZIP CODE: __________________________ COUNTRY:__________________________
ADDRESS:________________________________________________________________ CITY:______________________________________________________
NAME: ___________________________________________________________________ COMPANY: ________________________________________________
To validate your warranty and receive any future updates concerning your product, you must complete and return this Warranty Registration Card within 10 days of
purchase. (Please Print)
34551 Ardenwood Blvd.
Fremont, CA 94555-3607
Mylex Corporation
Customer Service Dept.
Place
Postage
Here