Philips SpeedPro Aqua 无绳立式吸尘器 FC6729/82 Important Information Manual

3000.032.0004.2 29/3/2019
> 75% 循环再造纸
保留备用
1
2
3
4
5
6
1
2
2
2
1
7
8
9
1
1
2
10
>75 % recycled paper
>75 % papier recyclé
English
Important safety information
Read this important information carefully before you use the appliance and
its accessories and save it for future reference. The accessories supplied
may vary for different products.
Danger
-
Never vacuum up water or any other liquid. Never vacuum up flammable
substances and do not vacuum up ashes until they are cold.
Never immerse the appliance or the adapter in water or any other liquid,
nor rinse it under the tap.
Warning
-
-
-
-
-
Check if the voltage indicated on the adapter corresponds to the local
mains voltage before you connect the appliance.
Always check the appliance before you use it. Do not use the appliance
or the adapter if it is damaged. Always replace a damaged part with one
of the original type.
The adapter contains a transformer. Do not cut off the adapter to
replace it with another plug, as this causes a hazardous situation.
This appliance is not intended for use by persons (including children)
with reduced physical, sensory or mental capabilities, or lack of
experience and knowledge, unless they have been given supervision or
instruction concerning use of the appliance by a person responsible for
their safety.
Children should be supervised to ensure that they do not play with the
appliance.
Keep the appliance and its cord out of the reach of children.
The plug must be removed from the socket-outlet before cleaning or
maintaining the appliance.
Unplug the adapter if you are not going to use the appliance for some
time.
Do not let the motorized brush move over the mains cords of other
appliances or other cables as this may cause a hazard.
Keep loose clothing, hair and body parts away from the motorized
brushes.
Do not cover or block the ventilation openings when the appliance is
operating.
To prevent damage, do not use the appliance if the filter is not present in
the dust container.
Do not block the appliance inlet when operating.
To prevent damage, never put ethereal oils or similar substances in the
water tank or let the appliance pick them up.
Do not lift or tilt the nozzle when the water tank is assembled and full, as
water may spray out of the water tank.
This appliance contains a rechargeable battery that can only be replaced
by a skilled person. Do not open the appliance to replace the
rechargeable battery.
The rechargeable battery may only be replaced by qualified service
engineers. Take the appliance to an authorized Philips service center to
have the battery replaced when you can no longer recharge it or when it
runs out of power quickly.
Do not store the appliance at a temperature above 40°C or below 5°C.
Do not use the appliance in a room with a temperature above 40°C.
Do not incinerate, disassemble or expose the appliance to temperatures
above 60°C. The rechargeable battery may explode if overheated.
This vacuum cleaner is designed for household use only. Do not use this
vacuum cleaner to vacuum up building waste, cement dust, ashes, fine
sand, lime and similar substances. Never use the vacuum cleaner without
any of the filters. This could damage the motor and shorten the life of
the vacuum cleaner. Always clean all parts of the vacuum cleaner as
shown in the user manual. Do not clean any parts with water and/or
cleaning agents if this is not specifically shown in the user manual.
Caution
-
-
-
Only charge the appliance with the adapter supplied. Only use 29V
adapter ZD12D290050.
During charging, the adapter becomes warm to the touch. This is normal.
Do not plug in, unplug or operate the appliance with wet hands.
Do not remove the adapter from the wall socket by pulling at the cord
(Fig. 1). Always unplug the appliance by first detaching the magnetic
connector from the magnetic charging disk (Fig. 2).
Always switch off the appliance after use and before you charge it.
Never block the exhaust air openings during vacuuming.
Do not clean the dust container or the dust container lid in the
dishwasher. They are not dishwasher-proof.
Do not clean the filter with scouring pads or abrasive cleaning agents.
Always use the vacuum cleaner with the filter unit assembled.
If you clean the filter with water, make sure that it is completely dry
before you put it back into the filter holder and dust container. Do not
dry the filter in direct sunlight, on the radiator or in the tumble dryer. Do
not clean the filter holder with water. This part is not washable.
Replace the filter if it can no longer be cleaned properly or if it is
damaged (see 'Ordering accessories').
Never use any accessories or parts from other manufacturers or that
Philips does not specifically recommend. If you use such accessories or
parts, your guarantee becomes invalid.
-
-
-
-
-
-
Make sure that the temperature in the room where the appliance is
stored or charged is between 5°C and 40°C.
Make sure that the appliance is installed with the wall fixture mounted to
the wall according to the instructions in the user manual.
Be careful when you drill holes in the wall to attach the wall fixture, to
avoid the risk of electric shock.
If you use the appliance to vacuum fine sand, lime, cement dust and
similar substances, the pores of the filter will become blocked. Clean the
filter regularly.
As this appliance uses water to clean, the floor may remain wet and
slippery for a while (Fig. 3).
To prevent damage, never put wax, oil, floor maintenance products or
liquid floor cleaners that are not water-dilutable in the water tank.
Do not mix different types of liquid floor cleaner. When you have used
one liquid floor cleaner, first empty and rinse the water tank before you
add another liquid floor cleaner to the water in the water tank.
To prevent damage, do not use liquid floor cleaners that are not
transparent or even milky.
Never exceed the maximum quantities mentioned on the bottle when
you use a liquid floor cleaner. Do not add more than a few drops to the
water in the water tank, as this tank has a capacity of 200ml.
Do not clean the metal wetting strip with a sharp object, as this may
damage the strip. Only clean the wetting strip by rinsing it under the tap.
Replace the wetting strip when you can no longer clean it.
Replace the wetting strip only with an original strip. For ordering a new
strip, see chapter 'Ordering accessories'.
Clean the water tank according to the instructions. The water tank is not
dishwasher-proof.
Do not use aggressive cleaning agent or tools to clean the Aqua Boost
pedal.
After mopping the floors, do not store the appliance with the water tank
attached on the wall mount. If you do this, the wet mopping pad will
touch the wall and this may damage the wall. Always remove the water
tank before you store the appliance.
To guarantee good cleaning results and proper functioning of the
appliance and water tank, always use original Philips cleaning pads.
Electromagnetic fields (EMF)
This Philips appliance complies with all applicable standards and
regulations regarding exposure to electromagnetic fields.
Using the appliance
Usage restrictions
-
Only use the water tank on hard floors with a water-resistant top coat
(such as linoleum, enameled tiles and varnished parquet) and stone
floors (such as marble). If your floor has not been treated to make it
water-resistant, check with the manufacturer if you can use water to
clean it. Do not use the water tank on hard floors of which the waterresistant top coat is damaged.
- Only use the water tank on linoleum floors that are properly affixed to
prevent linoleum from being drawn into the mopping nozzle.
- Do not use the water tank to clean carpets.
- Do not move the appliance with water tank assembled sideways, as this
leaves water traces. Only move forwards and backwards.
Note: Runtime duration depends on power level used during cleaning.
Mopping pad and wetting strip
The appliance comes with one wetting strip and two microfiber mopping
pads. With the water tank, wetting strip and microfiber mopping pad
attached to the standard floor nozzle, you can clean hard floors.The aquacolored mopping pad with wide stripes (FC8063) is suitable for mopping
stone and tiled floors.
Using liquid floor cleaner in the water tank
If you want to add a liquid floor cleaner to the water in the water tank, make
sure that you use a low-foaming or non-foaming liquid floor cleaner that
can be diluted in water. As the water tank has a capacity of 200ml, you only
have to add a few drops of liquid floor cleaner to the water.
Cleaning the water tank
To clean the water tank, mix one part vinegar with three parts water. Pour
this mixture into the water tank and close the cap. Shake the water tank and
put the water tank on a water-resistant surface. Leave the water-vinegar
mixture in the water tank overnight. Then empty the water tank, rinse it
thoroughly with fresh water, and use it normally again.
Caution: Water will leak from the water tank during cleaning, with the
wetting strip mounted and without the wetting strip.
To empty the water tank, hold the water tank over a sink, remove the cap
and tilt the water tank to the side of the filling hole. Then turn the water tank
over to let the water pour into the sink. To remove the remaining water from
the water tank, turn the water tank on its long side with the filling hole
pointing towards the sink. Then tilt the water tank forwards to let the
remaining water flow out of the water tank.
Note: Always store the water tank with the cap removed from the filling
hole.
Ordering accessories
To buy accessories or spare parts, visit www.philips.com/parts-andaccessories or go to your Philips dealer. You can also contact the Philips
Consumer Care Center in your country (see the international warranty
leaflet for contact details).
Warranty and support
If you need information or support, please visit www.philips.com/support
or read the international warranty leaflet.
Recycling
-
-
-
Do not throw away the product with the normal household waste at the
end of its life, but hand it in at an official collection point for recycling. By
doing this, you help to preserve the environment.
This product contains a built-in rechargeable battery which shall not be
disposed of with normal household waste. Please take your product to
an official collection point or a Philips service center to have a
professional remove the rechargeable battery.
Follow your country’s rules for the separate collection of electrical and
electronic products and rechargeable batteries. Correct disposal helps
prevent negative consequences for the environment and human health.
Removing the rechargeable battery
Only remove the rechargeable battery when you discard the product.
Before you remove the battery, make sure that the product is
disconnected from the wall socket and that the battery is completely
empty.
Take any necessary safety precautions when you handle tools to
open the product and when you dispose of the rechargeable battery.
1 Remove the dust container from the appliance.
2 Pull the display cover from the top of the handgrip (Fig. 4).
3 Undo the screw of the handle cover and pull the handle cover off the
appliance (Fig. 5).
4 Undo the bottom cover screw (1) and then remove the side panels. (Fig.
6)
5 Remove the bottom cover screws on the left and right side (1). Then
remove the bottom cover (2) (Fig. 7).
6 Disconnect the battery connector and the display connector from the
printed circuit board (Fig. 8).
7 Undo the battery frame screws (Fig. 9).
8 Remove the battery from the appliance and dispose of it according to
the rules (Fig. 10).
Troubleshooting
This chapter summarizes the most common problems you could encounter
with the appliance. If you are unable to solve the problem with the
information below, visit www.philips.com/support for a list of frequently
asked questions or contact the Consumer Care Center in your country.
Problem
Possible cause
The appliance does When the battery is
not work when I
empty,the bottom
push the button.
segment of the
display flashes red.
The appliance has
a lower suction
power than usual.
Solution
To charge the battery,
connect the appliance to the
charging base or attach the
handheld vacuum cleaner
directly to the magnet on the
charging base.
You have to push the
slider forward to
switch on the
appliance.
Push the slider forward to
setting 1 to switch on.
Increase the suction power
further by pushing the slider
to setting 2 to clean dirty
surfaces.
The filter and the
cyclone are dirty.
Clean the filter and the
cyclone. Make sure that you
wash the sponge filter at
least once a month if you use
the appliance regularly.
You have not
attached the dust
container lid properly
to the dust container.
You have not
attached the dust
container to the
appliance properly.
In both cases, there
will be a loss of
suction power.
Make sure that you attach
the dust container lid to the
dust container and the dust
container to the appliance
properly.
An object may be
Remove the tube and check
stuck inside the tube. for blockages.
Dust escapes from
the appliance.
The filter is dirty.
Clean the filter.
The filter is not
present in the
appliance.
Make sure that the filter is in
the appliance and assembled
correctly.
Something blocks
the cyclone.
Check the cyclone for objects
stuck in it and remove any
object that blocks the
cyclone.
Problem
Possible cause
Solution
If dust falls out of the Empty the dust container and
dust container, the
attach the dust container lid
dust container lid is
correctly.
probably not
attached properly to
the dust container.
The appliance does You selected a too
not move smoothly high suction power.
across the floor
when cleaning a
carpet.
Reduce the suction power by
choosing setting 1.
The brush does not The brush
Clean the brush with a pair of
turn anymore.
encounters too much scissors or by hand.
resistance.
The brush may stop
Switch off the appliance and
turning when it
then switch it back on again.
encounters too much
resistance from highpile carpet.
You have not
installed the roller
brush in the nozzle
properly after
cleaning.
Follow the instructions in the
cleaning chapter of the user
manual to slide the roller
brush into the nozzle
properly and secure it inside
the nozzle by snapping home
the locking lever.
The LEDs in the
nozzle do not
come on.
You have not
attached the nozzle
to the appliance or
handheld properly.
Attach the nozzle to the
appliance or handheld
properly.
The appliance is
not charging.
The magnetic
connector is not not
connected correctly
to the charging disk
or the adapter is not
inserted into the wall
socket properly.
Make sure that the magnetic
connector is connected
properly to the charging disk
and that the adapter is
inserted into the wall socket
properly.
You have not
connected the
correct adapter and
cord.
Make sure that you use the
correct adapter and cord.
If you have checked the
above and the appliance still
does not charge, take it to a
Philips service center or
contact the Consumer Care
Center via
www.philips.com/support.
FC6729: The mini
turbo brush does
not function
properly.
The roller brush is
blocked.
Remove hairs from the brush
with a pair of scissors (see
user manual).
The roller brush is
blocked by fabric or
surfaces during
cleaning.
Keep the mini turbo brush
aligned with the surface and
do not push the turbo brush
into soft surfaces.
The mini turbo brush
is not fully closed.
Make sure that the top and
bottom parts of the mini
turbo brush are properly
connected and there is no
gap between the two parts.
Check if the locking ring is in
closed position (see user
manual).
Your vacuum cleaner
builds up static
electricity. The lower
the air humidity, the
more static electricity
the appliance builds
up.
Discharge the appliance by
frequently holding the tube
against other metal objects in
the room (for example the
legs of a table or chair, etc.).
You can also raise the air
humidity level in the room.
You vacuumed up
fine sand, lime or a
similar substance.
This also causes
static electricity.
Empty the dust container and
clean the filter according to
the instructions in the user
manual.
The bottom
segment of the
display flashes red.
The battery is empty.
To charge the battery,
connect the appliance to the
charging base or attach the
handheld vacuum cleaner
directly to the magnet on the
charging base.
All segments of the
display flash
quickly.
An error has
occurred.
First try to recharge the
appliance, empty the dust
container and clean the filter.
If this does not help, take the
appliance to a Philips service
center or contact the
Consumer Care Center via
www.philips.com/support.
When I use my
vacuum cleaner I
sometimes feel
static electricity
shocks.
The water flow
The wetting strip is
Remove the wetting strip and
from the water tank blocked by excessive clean it.
is reduced.
residue.
The output of
water is faster and
larger than normal.
The microfiber
mopping pad is not
placed correctly and
blocks the wetting
strip as a result. This
prevents water from
flowing out of the
wetting strip.
Make sure that you place the
mopping pad correctly. Check
the user manual for proper
placement.
The water tank is
empty or nearly
empty.
Refill the water tank.
You use a microfiber
mopping pad that is
not supplied by
Philips.
Only use an original Philips
microfiber mopping pad. You
can buy these mopping pads
in the online Philips shop at
www.philips.com/parts-andaccessories or at your Philips
dealer. You can also contact
the Philips Consumer Care
Center in your country (see
the international warranty
leaflet for contact details).
If the water tank
Check the cap and make sure
produces an
it is fully and properly closed.
uncontrolled and too
large amount of
water, the cap of the
tank is probably not
closed properly.
The strip is not
placed properly in
the bottom of the
water tank.
The floor dries with
stripes when I use
the water tank.
Check the strip and make
sure that it is fitted properly
in the bottom plate of the
water tank.
You added too much Use only a few drops or use a
liquid cleaner to the
cleaner that foams less.
water.
简体中文
重要安全信息
使用本产品及其附件之前，请仔细阅读本重要信息，并妥
善保管以供日后参考。 随附的附件可能因产品而异。
危险
- 切勿吸入水或其他任何液体。 切勿吸入易燃物质，也不
要吸入未冷却的灰烬。
- 切勿将本产品或适配器浸入水或其他任何液体中，也不
要将它们放在水龙头下冲洗。
警告
- 在将本产品连接电源前，务必检查当地的电压是否与电
源适配器所标电压一致。
- 使用前，请务必检查产品。 如果产品或适配器受损，请
停止使用。 请务必用原装型号更换损坏的部件。
- 适配器中包含一个变压器。 请勿剪下适配器更换其他插
头，否则将导致严重后果。
- 产品不建议由有肢体、感官或精神能力缺陷或缺少使用
经验和知识的人（包括儿童）使用，除非有负责他们安
全的人对他们进行与产品使用有关的监督或指导。
- 请照看好儿童，本产品不能用于玩耍。
- 将产品及其线缆放在儿童接触不到的地方。
- 清洁或维护产品之前，必须先从插座拔掉插头。
- 如果在一段时期内不使用本产品，请拔下适配器插头。
- 切勿让电动刷在其它产品的电源线或其它线缆上移动，
否则可能会引发危险。
- 确保宽松的衣服、毛发和身体部位远离电动刷。
- 产品运行时，切勿覆盖或堵塞通风口。
- 为防止受损，请在集尘桶中放置过滤网后再使用本产
品。
- 运行时，切勿堵塞产品的进风口。
- 为防止受损，切勿将香精油或类似物质放入水箱中，也
不要用产品清扫它们。
- 组装水箱及水箱已满时，请勿提起或倾斜吸嘴，否则水
可能会从水箱中喷出。
- 本产品包含充电电池，只能由技术人员更换。 切勿拆开
本产品更换充电电池。
- 只有具备资格的服务工程师才能更换充电电池。 当充电
电池无法继续充电或耗电很快时，请将产品送往授权的
飞利浦服务中心，以更换电池。
- 切勿将产品存放在温度超过 40°C 或低于 5°C 的环境
中。
- 切勿在温度超过 40°C 的房间中使用产品。
- 切勿焚烧、拆卸产品或者将其暴露在温度超过 60°C 的
环境中。 如果过热，充电电池可能会爆炸。
- 根据设计，本吸尘器仅限于家用。 切勿使用本吸尘器清
理建筑垃圾、水泥灰、灰尘、细沙、石灰和类似的物
质。 切勿在没有任何滤网的情况下使用本吸尘器。 这会
损坏马达并缩短吸尘器的使用寿命。 务必按照用户手册
中的说明清洁吸尘器的所有部件。 请勿使用水和/或清洁
剂清洁任何部件（如果用户手册中未特别说明）。
警告
- 只能用随附的适配器为本产品充电。请仅使用 29V 适配
器 ZD12D290050。
- 充电期间，适配器会有微热。 这是正常现象。
- 切勿用湿手插入、拔下或操作产品。
- 切勿以拉拔电源线 (图 1)的方式将适配器从电源插座上
拔下。 拔下产品时，务必先将磁性连接器从磁性充电圆
盘 (图 2)上取下。
- 使用后和充电前，请务必关闭产品。
- 吸尘时切勿阻塞排气口。
- 切勿在洗碗机中清洗集尘桶或集尘桶盖。 这些部件不可
在洗碗机中清洗。
- 请勿使用丝绒型洗刷用具或腐蚀性清洁剂清洁过滤网。
- 使用吸尘器时，请确保装上过滤部件。
- 如果用水清洁过滤网，确保其完全干燥后再放回过滤网
架和集尘盒中。 切勿在直射的阳光下、散热器上或滚筒
式烘干机中干燥过滤网。 切勿用水清洁过滤网架。 该部
件不可水洗。
- 如果无法再洗净过滤网或其已损坏 (请参见 '订购配件
')，请予以更换。
- 切勿使用其他制造商生产的或未经飞利浦特别推荐的任
何配件或部件。 如果您使用了此类配件或部件，本产品
的保修将会失效。
- 请确保产品存放或进行充电的房间温度在 5°C 和
40°C 之间。
- 请确保按照用户手册中的说明，用壁装装置将产品安装
到墙上。
- 请注意，在墙上钻孔安装壁装装置时，请避免触电风
险。
- 如果在使用吸尘器清洁细沙、石灰、水泥灰和类似物
质，滤网孔会被堵塞。 定期清洁过滤网。
- 因本产品使用水来清洁，清洁后的一段时间内 (图 3)地
板上会有些湿和打滑。
- 为防止受损，切勿将蜡、油、地板维护产品或非水稀释
性液体地板清洁剂倒入水箱中。
- 切勿混合不同类型的液体地板清洁剂。 使用一种地板清
洁剂后，需要先倒空并冲洗水箱，然后才能在水箱的水
中加入另一种液体地板清洁剂。
- 为防止受损，请不要使用非透明或乳状的液体地板清洁
剂。
- 使用液体地板清洁剂时，切勿超过瓶子上标示的最大
量。 由于水箱的容量为 200 毫升，您只需加入几滴清洁
剂即可。
- 请勿用尖锐物体清洁湿的金属条，否则可能造成损坏。
只能在自来水下清洁湿的金属条。 无法再清洁干净时，
请更换湿的金属条。
- 只能使用原装金属条更换湿的金属条。 要订购新的金属
条，请参阅“订购附件”一章。
- 根据说明清洁水箱。 水箱不可用洗碗机清洗。
- 请勿使用腐蚀性清洁剂或使用工具来清洁 Aqua Boost
踏板。
- 清洁完地板后，请不要将装有水箱的本产品存放于壁挂
上。 否则，湿清洁布将接触墙壁并可能对墙体造成损
坏。 存放本产品之前请务必先卸下水箱。
- 为保证良好的清洁效果及产品和水箱的正常运作，请务
必使用原装飞利浦清洁布。
电磁场 (EMF)
本 Philips 产品符合所有有关暴露于电磁场的适用标准和法
规。
使用本产品
使用限制
- 仅在具有防水表面涂层的硬地板（例如油毯地板、瓷板
和刷漆木地板）和石材地板（例如大理石）上使用水
箱。 如果您的地板未经过处理，且不具有防水作用，请
咨询制造商，了解是否可以用水清洁。 请勿在防水表面
涂层损坏的硬地板上使用水箱。
- 仅在正确贴合的油毯地板上使用水箱，以防止油毯吸入
拖地吸嘴中。
- 请勿使用水箱清洁地毯。
- 请勿侧向移动装有水箱的产品，这样会留下水痕。 只能
前后移动。
注意： 运行时持续时间取决于清洁期间所使用的功率大
小。
清洁布和湿的金属条
本产品随附一个湿的金属条和两块微纤维清洁布。 安装好
水箱后，您可以将湿的金属条和微纤维清洁布安装到标准
地板吸嘴，以便用于清洁硬地板。而湖绿色宽条纹清洁布
(FC8063) 适合清洁石材和瓷砖地板。
在水箱中使用液体地板清洁剂
如果您要在水箱的水中加入液体地板清洁剂，请确保使用
可在水中稀释的低泡沫或无泡沫液体地板清洁剂。 由于水
箱容量为 200 毫升，您只需在水中加入几滴液体地板清洁
剂即可。
清洁水箱
如需清洁水箱，请将一份醋与三份水混合。 将混合液倒入
水箱中，盖上盖子。 摇晃水箱，然后将水箱放在防水表面
上。 将水醋混合液在水箱中存放一夜。 然后，倒空水箱，
用清水彻底冲洗后再正常使用。
警告： 在清洁过程中，不论是否安装湿的金属条，水都会
从水箱中的漏出。
要倒空水箱，请将水箱拿到水槽上方，取下水箱盖，并向
注水孔一侧倾斜水箱。 然后将水箱翻转过来，以便让水流
入水槽。 要将剩余的水从水箱中倒出，请沿水箱的长边翻
转，并将注水孔朝向水槽。 然后向前倾斜水箱，以便让剩
余的水从水箱中流出。
注意： 存储水箱时，务必从注水孔上取下盖子。
订购配件
如需购买附件或备件，请访问 www.philips.com/parts-andaccessories 或联系您的飞利浦经销商。 您还可以联系所
在国家/地区的飞利浦客户服务中心（请参阅国际保修卡了
解详细联系信息）。
保修和支持
如需信息或支持，请访问 www.philips.com/support 或阅读
国际保修卡。
回收
- 弃置本产品时，请不要将其与一般生活垃圾放在一起，
应将其交给政府指定的回收中心。 这样做将有利于环
保。
- 此产品包含内置充电电池；请勿将充电电池与一般生活
垃圾一起弃置。 请您将产品送到官方收集中心或飞利浦
服务中心，请专业人士移除充电电池。
- 遵循您的国家/地区有关分类回收电子电气产品和充电电
池的规定。 正确弃置产品有助于避免对环境和人类健康
造成不良后果。
ˌɫǩ؆
໾
(Pb)
мȞġĈҴˀΙĀǩ؆Ӎߒʔ
ĈҴˀΙ
᰽
⬡
ԣ͍Ჱ
(Hg)
(Cd)
(Cr (VI) )
Ġ⅑ԓ᧠ Ġ⅑ȕ᧠⓭
(PBB)
(PBDE)
֦ǗК‫ۃ‬ଠ،
O
O
O
O
O
O
Ǘ۷ҒԜ،
O
O
O
O
O
O
ǕȪϜ֪֙ SJ/T 11364 Ā‫ܪ‬ǭৠ̑뺯
OȪФ˽ĈҴˀΙć˽ˌɫǨĈߴΙࠒնġĀߒʔߴć GB/T 26572 ‫ܪ‬ǭĀՄʔđ̂ŘĪ뺯
XȪФ˽ĈҴˀΙψɺć˽ˌɫĀԚĂߴΙࠒնġĀߒʔɸŜ GB/T 26572 ‫ܪ‬ǭĀՄʔđ̂뺯
拆下充电电池
必须在丢弃本产品前拆下充电电池。 卸下电池之前，请确
保本产品与电源断开连接并且电池电量已耗尽。
当您使用工具打开本产品时以及在您弃置充电电池时，请
采取必要的安全保护措施。
1 从产品上卸下集尘盒。
2 拆下手柄 (图 4)顶部的显示屏盖。
3 拧下手柄盖的螺钉，然后将手柄盖从产品 (图 5)上取
下。
4 拧下底盖螺钉 (1)，然后卸下两侧面板。 (图 6)
5 卸下左侧和右侧的底盖螺钉 (1)。 然后卸下底盖 (2) (图
7)。
6 从印刷电路板 (图 8)上断开电池连接器和显示屏连接
器。
7 拧下电池架螺钉 (图 9)。
8 从产品中取出电池并按照规定 (图 10)处理电池。
故障处理方法
本章归纳了使用本产品时最常见的一些问题。 如果您无法
根据以下信息解决问题，请访问 www.philips.com/support
查阅常见问题列表，或联系您所在国家/地区的客户服务中
心。
问题
可能的原因
解决方法
按下按钮时，
产品不工作。
电池电量耗尽
为电池充电时，请将产
时，显示屏底段 品连接到充电座，或将
呈红色闪烁。
手持式吸尘器直接连接
到充电座的磁体上。
必须向前推动滑 将滑块向前推动到设置
块才能打开产
1 以打开。 将滑块向
品。
前推动到设置 2 以进
一步增加吸力来清洁脏
污表面。
本产品的吸力
比往常要小。
过滤网和旋风滤 清洁过滤网和旋风滤网
网不干净。
。 如果您经常使用本
产品，请确保每月至少
清洗一次海绵滤网。
您未将集尘盒盖
正确安装到集尘
盒上。 您未将
集尘盒正确安装
到产品上。 在
这两种情况下，
吸力将降低。
请确保您将集尘盒盖正
确安装到了集尘盒上，
并将集尘盒正确安装到
了产品上。
管内可能卡有物 取下管件并检查阻塞情
体。
况。
灰尘从产品中
溢出。
过滤网变脏。
清洁过滤网。
滤网未放入产品 确保滤网已放入产品并
中。
正确安装。
污垢堵塞了旋风 检查旋风滤网是否被物
滤网。
体卡住，并清除任何堵
塞旋风滤网的物体。
如果灰尘从集尘 倒空集尘盒，并正确安
盒中掉出，则集 装集尘盒盖。
尘盒盖可能未正
确安装到集尘盒
上。
清洁地毯时，
产品无法在地
板上顺畅移
动。
您选择的吸力太 通过选择设置 1 来降
大。
低吸力。
滚刷不再旋
转。
滚刷遇到的阻力 用剪刀或用手清洁滚
太大。
刷。
滚刷在长毛绒地 关闭产品，然后将其重
毯上遇到太大阻 新打开。
力时，可能会停
止转动。
您没有在清洗滚 请按照本用户手册“清
刷后将其正确安 洁”一章中的说明，将
装到吸嘴上。
滚刷正确滑入吸嘴，并
将锁定杆扣合到位，以
便将滚刷固定到吸嘴
内。
吸嘴中的 LED
指示灯不亮。
您未将吸嘴正确 将吸嘴正确安装到产品
安装到产品上， 上，或采用正确的手持
或未正确手持。 方式。
产品未充电。
磁性连接器未正
确连接到充电圆
盘，或适配器未
正确插入电源插
座。
请确保磁性连接器正确
连接到充电圆盘，且适
配器正确插入电源插
座。
您没有连接正确 请确保使用正确的适配
的适配器和电源 器和电源线。
线。
如果已执行上述检查但
产品依然无法充电，请
将其送至飞利浦维修中
心，或通过
www.philips.
com/support 联系客户
服务中心。
FC6729： 迷
你涡轮刷无法
正常工作。
滚刷被阻塞。
用剪刀清除刷子上的毛
发（请参见用户手
册）。
清洁过程中，滚 保持迷你涡轮刷与表面
刷被织物或表面 对齐，且请勿将涡轮刷
阻塞。
推入软质表面。
迷你涡轮刷未完 确保迷你涡轮刷的顶部
全关闭。
和底部正确连接，两部
分之间没有间隙。 检
查闭锁环是否处于关闭
位置（请参见用户手
册）。
有时，在使用
吸尘器时会有
触静电的感
觉。
吸尘器会积聚静
电。 空气湿度
越低，产品积聚
的静电就越多。
经常握住硬管使其与房
间中的其它金属物体接
触（例如，桌椅脚
等），对产品进行放
电。 您也可以增加房
间的空气湿度。
问题
可能的原因
解决方法
您使用本产品清 请清空集尘盒，并按照
理细沙、石灰或 用户手册中的说明清洁
类似的物质。
滤网。
这还会引发静
电。
显示屏底段呈
红色闪烁。
电池已耗尽。
为电池充电时，请将产
品连接到充电座，或将
手持式吸尘器直接连接
到充电座的磁体上。
显示屏所有指
示段快速闪
烁。
发生错误。
首先尝试为产品充电，
倒空集尘桶并清洁过滤
网。 如果这不起作
用，可以将产品送至飞
利浦维修中心，或通过
www.philips.
com/support 联系客户
服务中心。
水箱的水流量
减少。
湿的金属条被过 卸下湿的金属条，并进
多的残留物阻
行清洁。
塞。
微纤维清洁布未
正确放置，因此
阻塞了湿的金属
条。 这样可以
防止水从湿的金
属条流出。
请确保您正确放置了清
洁布。 有关如何正确
放置的方法，请参阅本
用户手册。
水箱为空或几乎 为水箱加水。
无水。
您使用了非飞利 仅限于使用原装飞利浦
浦提供的微纤维 微纤维清洁布。 您可
清洁布。
以在飞利浦网上商城
www.philips.
com/parts-andaccessories 或飞利浦
经销商处购买这些清洁
布。 您还可以联系所
在国家/地区的飞利浦
客户服务中心（请参阅
国际保修卡了解详细联
系信息）。
出水速度比通
常更快，量更
大。
如果水箱出水速 检查水箱盖并确保其已
度不可控且水量 完全闭合盖好。
过大，则可能是
水箱盖没盖好。
金属条未正确置 检查金属条并确保其已
于水箱底部。
正确安装在水箱底板
上。
当使用水箱
时，地板出现
干纹。
向水中加入了过 只需使用几滴或使用泡
多液体清洁剂。 沫较少的清洁剂。
̊֩ᴮᮮѱ฿੗઺ஷፗᄱሺա࠭ٛ
‫ڿ‬Եᴮ)&
ᮜ߳ၶԀᴮ9ᵲ9
ᮜ߳ᮓ࿾ᴮ+]
ᮜ߳ၶสᴮ$
ၪ̊ஹణᴮឣᜬ̊֩ࣸ᥽
̊‫ڔ‬ᴮˊ‫ځ‬රᔍᔍࢪ
ᮮѱ฿ᴜˊ‫ځ‬ᴝ੹᠞ఙᬀАԶ
ʰๅࢽ᭕ߪӐ༚ᅶᡬԵ$࣢
Ў‫ځ‬ᮂߺజҟཊጦ
న̊֩ಝ૩‫ځ‬ಉ*%
*%*%Ԗ
*%ѷᤨ
保留备用
发行日期: 29/3/2019