TOGUARD Backup Camera Kit, 7’’ LCD Rear View Monitor Vehicle Backup Camera User Manual

TOGUARD CA711
Rearview Monitor Kit
TFT color monitor
. Channel switch:
. Rotation image left/right/up/down
. MENU
. Decrease button-for adjusting value in menus.
. Increase button-for adjusting value in menus.
. Power: Turn On/Off the monitor.
. IR Window
NO0OBA SON
r LEO REMOTE *
Ces,
IS WN
Se
4. MENU
5. VOL-: decrease level
6. MODE: display select
1. Power: Turn On/Off the device.
2. Video Channel Switch
3. VOL +: Increase level
1. Sun-visor
2. Rotation screw
3. IRLEDS
4. Metal housing
5. bracket
6. Lens
1. INTRODUCING
Thanks for purchasing Toguard backup camera!
With this manual, you will be able to properly install and operate
the unit.
Please read this manual thoroughly before operating the unit,And
keep it for further reference.
If you have any other questions or problems, Please feel free to
contact us at
USA&Canada [email protected]
Europe [email protected]
UK [email protected]
Australia [email protected]
We have professional team at your service, and your satisfaction is
guaranteed.
2. BUTTON AND FUNCTIONS
12345 6 7
3.DEVICE PARAMETER
Monitor
Screen size: 7 inch (16:9)
Resolution: 800x480
System: PAL&NTSC
Video: Two-way video input.
Trigger wire for auto reversing
Power: DC12-24V
Power Consumption: 5W
Operate mode: Button operation / remote control
Work temp.: -10C-+40€
Storage temp.:-25C~+80C
External dimensions: 171Wx113Hx20D(mm)
Camera
Image Sensors: Color CMOS Camera
TV System: PAL / NTSC
Waterproof rate: IP67
Resolution: 480TV lines
Minimum Illumination: 0.2Lux / F1.2 (OLux with IR LEDs ON)
Pin Lens: f=2.5mm
Lens Angle: 120°
IR LEDs: 18pcs
Vertical Sync: Frequency: 50Hz / 60Hz
Video Output: 1.0vp-p, 750hm
Power Supply: DC 12-24V
Current Consumption: <300mA
Electronic Shutter: 1/60 - 1/10,000 Seconds
Gamma Consumption: 0.45
S/N Ratio: Better than 48Db
Scanning System: 2:1Interlace
Operating Temperature:-20*C-70*C ,RH95% MAX
Storage Temperature:-40°C-85°C ,RH95% MA
4.CONNECTION DIAGRAM
' Optional Cigarette
Lighter Power Socket
N == o_o 7
mm == === === == == == == == == == == == == == == == == == == == == == == == == == == == == == == == ==
BLACK: Ground
RED: ACC 12V-32V
GREEN: Reversing Lamp Positive
9.MONITOR AND CAMERA DIMENSION
1.Connect the trigger cable to the monitor.
2.Connect the trigger cable to car power:
RED lead to car ACC power positive.
Black lead to Ground.
Green lead to the reverse light positive lead.
3.Connect the trigger cable to the 15m extension cable.
4.Route the extension cable to the rear end of your car, near the
position to install the rear view camera.
b.Install the rearview camera on your car and connect the extension
cable, then secure the connector with the included rubber cover.
6.Route the excess cable.
7.Now when you put your car in Reverse Gear, the camera and the
monitor automatically turn on and display the rear image.
8.When you are out of Reverse Gear, the camera and the monitor
will automatically turn off.
NOTICE:
* The monitor can also be power with the included cigarette
lighter power adapter, however, if you installed it that way, the
monitor will not be triggered by reversing, need to be manually
turned on or turned off.
Cigarette Lighter Power Socket
* The monitor will automatically turn on when you put your car in
reverse, and turn off when you are not in reverse.
6